OWNER'S MANUAL
IMPORTANT!
WARRANTY INFORMATION INSIDE. PLEASE READ
FOR INQUIRIES CALL
1800 656 700
OR
WWW.TEAC.COM.AU
EU2845ST&2845W-MAV-1541-ENG-STEREO-1AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Keep this warranty information and your purchase receipt
Your proof of purchase (receipts) will enable fast and efficient service in the event of repair.
WARRANTY PROCEDURES
Please keep this information for your own records.
Please refer to the owner's manual to ensure that you have followed the correct installation and operating proce-
dures.
1. Read owner's manual carefully
2. If you require Warranty Service, please contact the TEAC Service Centre
3. Please have your purchase receipt as your proof of purchase and the following details completed for a valid
Warranty.
Owner's Name
Owner's Address
Postcode
Model Name/No.
Dealer's Name
Serial No.
Dealer's Address
Postcode
4. Please ensure that your product is packed appropriately upon return to the service centre.
If you have any other queries regarding service or warranty please contact the TEAC Service below:
TEAC Total Care Ph: 1800 656 700
EU2845ST&2845W-MAV-1541-ENG-STEREO-3AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Remote Control.............................................. 5 Teletext ......................................................... 18
1) To operate Teletext .......................................... 18
2) To select a page of Teletext ............................. 18
Control Panel Buttons and Rear Panel ....... 6
Safety and Precautions ................................. 7
Attention: .............................................................. 7
3) To Select Index Page ...................................... 18
4) To Select Teletext with a TV Programme ......... 18
5) Searching for a page while watching TV .......... 18
6) To Select Double Height Text .......................... 18
7) To Reveal “concealed” Information ................... 18
8) To StopAutomatic Page Change ..................... 18
9) To Select a Subcode Page .............................. 18
10 To exit Teletext ............................................... 19
11) To Display the Time ....................................... 19
12) Fastext ......................................................... 19
Preparation..................................................... 8
Features ............................................................... 8
Before Switching on your TV ....................... 8
Power connection.................................................. 8
Connections to the RF input socket ...................... 8
How to connect other devices................................ 8
Inserting batteries in the remote control handset ... 8
Switching the TV ON/OFF ............................. 9
To switch the TV on............................................... 9
To switch the TV off ............................................... 9
Connect Peripheral Equipment.................. 19
1) Via the Euroconnector..................................... 19
2) YCbCr Mode ................................................... 19
3) Via Ant Input ................................................... 19
4) Decoder .......................................................... 19
5) TV and Video Recorder ................................... 19
6) Playback NTSC.............................................. 20
7) Copy Facility ................................................... 20
8) Search for and store the test signal of the video
recorder............................................................... 20
9) Camera and Camcorder .................................. 20
10) Connect the decoder to the video recorder..... 20
11) Connecting Headphones ................................ 20
Operating the TV ........................................... 9
A.P.S. (Automatic Programming System) ............. 9
Operating with the buttons on the TV set .............. 9
Operating with Remote Control.............................. 9
Menu System ................................................ 10
Sound Menu........................................................ 10
Picture Menu ...................................................... 12
Feature Menu...................................................... 14
Installation Menu ................................................. 14
Program Menu .................................................... 15
Antenna Connections .................................. 21
Tips................................................................ 22
Care of the Screen .............................................. 22
Poor Picture ........................................................ 22
No Picture ........................................................... 22
Sound ................................................................. 22
Remote Control ................................................... 22
No solution.......................................................... 22
Other Features............................................. 16
1) TV Status ........................................................ 16
2) Programme Swap (P<P) ................................. 16
3) Double-digit (- -) .............................................. 17
4) Personal Preferences (PP) .............................. 17
5) Sound Indicator ............................................... 17
6) Picture Mode .................................................. 17
7) Blue Background During No-Signal.................. 17
8) Mute Indicator ................................................. 17
9) Volume Bar ..................................................... 17
10) AV Modes ..................................................... 17
Specifications............................................... 22
ENGLISH - 4 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-4AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
= Stand By
= Cursor Up
= Cursor Right
OK = No function
= Info (Program Menu)
0 - 9 = Direct Program
-/-- = Double Digit
P<P =Previous Programme
P/CH + = Programme Up
+ = Volume +
= TV / Quit Menu
= External Source
(EXT-1, RGB, YCbCr and F-AV)
Yellow (FEATURE) = Feature Menu
Blue (INSTALL) = Installation Menu
= Hold
= Update / Picture Mode Change ***
= Index Page
= Reveal
= Expand
= Mix
= Teletext
= Time
Red (SOUND) = Sound Menu
Green (PICTURE) = Picture Menu
= Mute
I-II = Mono/Stereo - Dual I-II
-
= Volume -
- P/CH = Programme Down
PP = Personal Preference
M = Menu
ꢀꢁ
ꢀꢂ
= Cursor Down
= Cursor Left
ꢀꢁ
= Picture Mode Change *** (AUTO, 4:3, 16:9, CINEMA, SUBTITLE, ZOOM)
ENGLISH - 5 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-5AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel Buttons and Rear Panel
FRONT PANEL
REAR PANEL
Speakers (left + right)
= Power On / Off
VIDEO (
)= VCR
H-PHONE ( ) = Headphone 3,6 mm Ø
ANT = Antenna (75 W)
-
+ = Volume -/+
- P/CH + = Program -/+
MENU = Menu
EXT.1 = Scart Socket 1 (RGB)
EXT.2 = Scart Socket 2 (YCbCr)
Power Cable
AUDIO L ( ) = Audio left
AUDIO R ( ) = Audio right
ENGLISH - 6 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-6AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Precautions
To ensure safe and reliable operation of the TV set,
please observe the following precautions in installa-
tion, operation and maintenance.
Safety:
1. Do not remove the back of housing by yourself, as
high voltages inside the unit are dangerous. If it is
necessary to open the back, ask a technician with
specialized service experience.
Attention:
1. Pay attention to the power supply cord before in-
stalling the TV set. Do not hang anything on the
cord, and avoid treading on the cord.
2. Remove the power supply plug from its socket in
case of the following conditions, and consult with
service personnel.
2. The slots on the housing back are designed for ven-
tilation to ensure reliable operation of the TV set
and prevent overheating. They must never be cov-
ered or blocked. The TV set must not be placed
near a heat source or it might be damaged.
(1) The power cord or plug are damaged or shows
cracking.
(2) Any object has fallen into or liquid flown into the
TV set.
(3) The performance of TV set has deteriorated sig-
nificantly or there is damage on the housing.
3. The outdoor antenna must not be erected close to
HV lines or other power supply lines. Use extreme
care when erecting the antenna and not to touch liv-
ing wires or injury may occur.
(4) The TV set will not operate normally according to
the instructions.
4. This TV set can only use the supply voltage and fre-
quency indicated on the back of the housing. If your
power supply does not comply with them, please
consult with the service personnel.
3. Please remove the power supply plug from its
socket when the TV set will not be used for a long
period of time.
Instructions for waste disposal:
5. Do not let any object fall into the ventilation open-
ings of the TV set housing, nor let any liquid flow
into the machine via the openings.
• Packaging and packaging aids are recyclable and
should principally be recycled. Packaging materials,
such as foil bag, must be kept away from children.
6. Do not subject the TV set to rain, or use it in a
damp environment. When cleaning dust, be sure to
remove the power supply plug from its socket first.
Do not clean the housing directly with liquid deter-
gent, use a damp cloth. Be sure to remove the
power supply plug from its socket and remove the
antenna plug during a thunderstorm or when it will
not be used for long time, to avoid components be-
ing damaged by lightning.
• Batteries, including those which are heavy metal-
free, should not be disposed of with household
waste. Please dispose of used batteries in an envi-
ronmentally sound manner. Find out about the legal
regulations which apply in your area.
“DO NOT LEAVE YOUR TV AT STAND-BY OR
OPERATING WHEN YOU LEAVE YOUR HOUSE”
7. If you use an indoor antenna, do not let it touch any
electrical appliance, or normal reception of TV pro-
grams may be affected.
ENGLISH - 7 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-7AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Dear Customer:
Thank you for purchasing our latest TV set.
Before Switching on your TV
Power connection
Please read this instruction manual carefully first be-
fore operation so that you can use it in a safe and reli-
able manner and bring all its functions into full play.
Please also keep it properly for future reference.
IMPORTANT: The TV set is designed to operate on
240V AC, 50 Hz.
• After unpacking, allow the TV set to reach the ambi-
ent room temperature before you connect the set to
the mains.
Preparation
For ventilation, leave a space of at least 10 cm free all
around the set. To prevent any fault and unsafe situa-
tions, please do not place any objects on top of the
set.
Connections to the RF input socket
• Connect the aerial or cable TV plug to the RF input
socket located at the back of the TV and connect the
cable plug coming out from the TV out socket lo-
cated at the devices (VCR, DVB etc.) to this socket
as well.
Use this apparatus in tropical and/or moderate cli-
mates.
Features
• It is a remote controlled colour television.
• 100 programmes from VHF, UHF bands or cable
channels can be preset.
How to connect other devices
• It can tune cable channels.
IMPORTANT: Switch off the TV before connecting any
external device.
• Controlling the TV is very easy by its menu driven
system.
Sockets for external connections are at the back and
front of the TV. For connection of other devices via Eu-
roconnector refer to the manuals of the related devic-
es.
• It has three Euroconnector socket for external de-
vices (such as computer, video, video games, audio
set, etc.)
• Optional mono or stereo sound systems (German +
Nicam) are available.
Inserting batteries in the remote control
handset
• Full function Teletext (Fastext).
• It is possible to connect headphone.
• Direct channel access.
• Place the batteries in the right directions as seen be-
low.
• A.P.S. (Automatic Programming System).
• All programmes can be named.
• Remove the battery cover located on the back of the
handset by gently pulling upwards from the indicated
part.
• Programme swapping between last watched two pro-
grammes.
• Insert two AAA (R03) or equivalent type batteries in-
side.
• Forward or backward automatic tuning.
• Sleep timer.
• Replace the battery cover.
• Child Lock.
• Automatic sound mute when no transmission.
• When no valid signal is detected, after 5 minutes the
TV switches itself automatically to stand-by mode.
• WSS (Wide Screen Signaling).
• NTSC Playback.
• YCbCr Mode.
• Front AV in.
• Headphone.
ENGLISH - 8 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-8AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Remove batteries from remote control handset • If you do not want to start A.P.S., you can cancel it
when it is not to be used for a long period. Otherwise it
can be damaged due to any leakage of batteries.
by pressing the “
” button on your remote control.
• When you start A.P.S. the below menu will appear
on the screen.
Switching the TV ON/OFF
To switch the TV on
Your TV will switch on in two steps:
Operating with the buttons on the TV set
1- Press the power button located on the front of the
TV. Then the TV switches itself to standby mode
and the RED LED located below the TV turns on.
Volume setting and programme selection can be made
using the buttons on the front of the TV.
2- To switch on the TV from stand-by mode either:
Volume Setting
Press a digit button on the remote control so that a
programme number is selected,
• Press “-
” button to decrease volume or “
+”
button to increase volume, so a volume level scale
(slider) will be displayed in the lower middle side of
the screen.
or,
Press Programme Up or Down buttons on the front of
the TV or on the remote control, so that last switched
off programme is selected.
Programme Selecting
• Press “P/CH+” button to select the next programme
or “-P/CH” button to select the previous programme.
By either ways the TV will switch on and the RED LED
will turn GREEN.
Entering MENU
To switch the TV off
• Press “MENU” button to enter the MENU. In the
MENU select sub-menu using “-P/CH” or “P/CH+”
• Press the stand-by button on the remote control, so
the TV will switch to stand-by mode and the GREEN
LED will become RED,
button and enter the sub-menu using “-
” or
“
+” button. To learn the usage of the menus, refer
or,
to the Menu System section.
Press the power button located on the front of the TV,
Operating with Remote Control
so the TV will switch off and the GREEN LED will turn
off.
The remote control handset of your TV is designed to
control all the functions of the model you selected.
The functions will be described in accordance with the
Operating the TV
You can operate your TV both using the remote menu system of your TV.
control handset and onset buttons.
Functions of the menu system are described in Menu
System section.
A.P.S. (Automatic Programming System)
Volume Setting
The A.P.S. menu will appear when you first switch on
your TV for the first time.
Press “
+” button to increase volume. Press
“- ” button to decrease volume. A volume level scale
(slider) will be displayed at the middle of the bottom on
the screen.
A.P.S. automatically programmes your TV, according
to the transmission of programme systems in your
area.
• By pressing the “ ” or “ ” buttons, come to the
Language item and select the language in which the
menus of the TV will appear. You can see the avail-
able languages by pressing “ ” or “ ” button. As
soon as you change the language, the menu items
will be displayed in the selected language.
Programme Selecting (Previous or next
programme)
• If you want to start A.P.S., by pressing the “ ” or
• Press “-P/CH” button to select the previous pro-
“
” buttons, come to the Start item and by pressing
gramme.
“ ” or “ ” button start the A.P.S..
• Press “P/CH+” button to select the next programme.
ENGLISH - 9 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-9AK45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme Selecting (direct access)
MENU
Press digit buttons on the remote control handset to
select programmes between 0 and 9. TV will switch to
the selected programme. To select programmes be-
tween 10 - 99, you must use the double digit button
"- / - -".
The menu system is described below.
The short way in order to enter the menus, press :
“M” Button,
Menu.
Red Button,
Green Button,
Yellow Button,
Blue Button,
“Info” Button,
Sound Menu.
Picture Menu.
Feature Menu.
Install Menu.
Program Menu.
Menu button has two functions; first is opening or
closing the “M”, and the second is closing the sub-
menu and then opening its parent menu.
Sound Menu
this OSD is displayed at the left hand upper
on the screen.
To change sound settings
• Enter the Sound Menu directly, pressing the Red
button or,
After then, press the digit buttons consecutively which
programme you want to select (eg. for programme 27,
first press 2 and then 7). When it is late to press any
digit button this function will be ignored and the dis-
play will be erased. In the same way it must not be
late to press any digit button after entering the first
digit. The limit of the delay time is 3 seconds.
• As you enter the MENU, sound will be the first se-
lected option. In the MENU, select SOUND using
“
” or “ ” button, then enter the sound menu press-
ing “ ” or “ ” button.
Setting Volume
Press directly the programme number to reselect sin-
gle digit programmes.
As you enter the sound menu, Volume will be the first
selected option.
Programme Swapping
• Press “ ” button to increase volume.
• Press "P<P" (programme swap) button to select the
last selected programme. This button provides swap-
ping between last two selected programmes. For ex-
ample, select programme 8, then select programme
2. Now, if you press "P<P" button, programme 8 will
be selected. If you press the same button again, pro-
gramme 2 will be selected and so on.
• Press “ ” button to decrease volume.
Or you can directly change the volume settings using
“
+” (to increase) or “-
” (to decrease) button.
Menu System
Your TV has been designed with a menu system, to
provide an easy manipulation of a multi-function sys-
tem. The TV is controlled by choosing the commands,
which are displayed on the screen.
Setting Balance
It allows adjusting the distribution between the left and
right speakers.
Press the “M” button. The MENU will be displayed in
the middle on the screen.
• Using “ ” or “ ” button select Balance.
• Press “ ” button to change balance rightward.
• Press “ ” button to change balance leftward.
All the selected items in this menu system is indicat-
ed with HIGHLIGHTED characters and with an arrow
on the leftside of items.
When balance control is in mid position, the cursor is
displayed with the two reciprocal arrows.
To select a sub-menu use “ ” or “ ” button, and press
“ ” or “ ” button. Each option can also be selected
with the coloured button and "
mote control.
" button on the re-
ENGLISH - 10 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A0K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Sound Mode
Pressing “ ” or “ ” button will change the current
sound mode. (e.g.: If the current sound mode is ste-
reo, it will be stereo or visa versa).
• Using “ ” or “ ” button select Mode.
• Press “ ” or “ ” button to change Mode.
In case of bilingual broadcast, you can select original
or dubbed language again using mode menu. So when
somebody listens to the original language from the
loudspeakers, somebody else can listen to the
dubbed language from headphone.
You can select MONO, STEREO, DUAL-I or DUAL-II
mode, only if the selected channel supports that
mode.
You can also change sound mode directly pressing “I-
II” button on your remote control.
To Store the Headphone Settings
• Using “ ” or “ ” button select Store. Press “ ” or
“ ” button to store current headphone volume and
balance. The stored values will be valid for all the pro-
grammes.
Equalizer
Setting Effect
To enter Equalizer sub-menu, select Equalizer using
You can use this feature to switch ON and OFF sound
effect. Pressing “ ” or “ ” button will turn on or off
this feature. If the current sound system is Mono and
the sound effect is set ON, then the sound will be
heard as if it is Stereo. If the current sound system is
Stereo, switching this effect on will make the sound
deeper. Switching it off will make no change in Mono
and Stereo.
“
” or “ ” button, then enter Equalizer menu press-
ing “ ” or “ ” button.
In case of bilingual broadcast (Dual Sound), you can
select original or dubbed language using mode option.
In Mode item there are four predefined and one user
defined options. These are PERSONAL, MUSIC,
SPEECH, JAZZ and FLAT. The predefined options can
not be changed by the user. The Personal option may
be adjusted by the user.
To Change Headphone Sound Settings
Pressing “ ” or “ ” button on Headphone, enter the
Headphone menu. This is a sub-menu of Sound menu,
and all options in this menu are working as the same
in the Sound menu.
The 5 items below the Mode are available to adjust
the sound settings in 5 frequency values: 120 Hz, 500
Hz, 1.5 kHz, 5 kHz and 10 kHz. To change the values
of 5 frequency options, select one of the options by
“
” or “ ” button, and then press “ ” to increase the
value, or “ ” to decrease the value.
To store the Equalizer settings, press “ ” or “ ” but-
ton on “Store” option.
Setting Headphone Volume
Setting Avl
• As you enter the Headphone sound menu, Volume
will be the first selected option.
Automatic Volume Limiting (AVL) function normalizes
sound to obtain fixed output level between programs,
having different sound levels. Pressing “ ” or “ ” but-
ton will turn ON and OFF this feature.
• Press “ ” button to increase volume.
• Press “ ” button to decrease volume.
Setting Headphone Sound Mode
• Using “ ” or “ ” button select Mode.
ENGLISH - 11 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A1K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
• Using “ ” or “ ” button select Colour.
• Press “ ” button to increase colour level.
• Press “ ” button to decrease colour level.
To Store the Settings
• Press “ ” or “ ” button on “STORE” option to store
Sound menu settings.
Setting Sharpness
Picture Menu
• Using “ ” or “ ” button select Sharpness.
• Press “ ” button to increase peaking level.
• Press “ ” button to decrease peaking level.
• To enter the Picture menu directly, press the
“GREEN” button, or
• Press “M” button, now you are in MENU. In the
MENU, select “PICTURE” using “ ” or “ ” button,
then enter the Picture menu pressing “ ” or “ ” but-
ton.
Setting Tilt
• Using “ ” or “ ” button select Tilt.
• Press “ ” button to increase tilt level.
• Press “ ” button to decrease tilt level.
Note: When Picture Mode is not “MANUAL”, BRIGHT-
NESS, CONTRAST and COLOUR options can not be
reached by “ ” or “ ” buttons.
Setting Brightness
You can change Brightness only when Picture Mode
is selected MANUAL.
• As you enter the picture menu, Brightness will be the
first selected option.
Setting Hue
• Press “ ” button to increase brightness.
• Press “ ” button to decrease brightness.
(During Playback NTSC system, this will appear in AV
mode only when NTSC video source is applied. Other-
wise, HUE option is invisible in Picture menu.):
• Using “ ” or “ ” button select Hue.
• Press “ ” button to increase hue level.
• Press “ ” button to decrease hue level.
Center value is indicated with the two reciprocal ar-
rows.
Setting Contrast
You can change Contrast only when Picture Mode is
selected MANUAL.
• Using “ ” or “ ” button select Contrast.
• Press “ ” button to increase contrast level.
• Press “ ” button to decrease contrast level.
Setting VCR Mode
• Using “ ” or “ ” button select VCR Mode.
• When you watch a picture from your VCR and the
picture is unstable, you may improve it by changing
the "VCR MODE" setting from "ON" to "OFF".
Setting Colour
You can change Colour only when Picture Mode is
selected MANUAL.
ENGLISH - 12 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A2K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
16:9
This mode restores the correct proportions of pictures
transmitted in 16:9 using full screen display.
Setting Picture Mode
This item is used to change the picture mode. By
Note: If you display a 4:3 picture in thid mode, it will
pressing “ ” or “ ” button you may select one of be enlarged horizontally.
these options: BRIGHT, STANDARD, SOFT, MANU-
AL.
CINEMA
The picture is enlarged to CINEMA format, a thin black
band remains on both sides of the picture.The “ ” or
” buttons allow you to compress and move the im-
age vertically to view the top or bottom of the picture
(subtitles).
“
Setting Colour Temp
This item is used to change the Colour Temperature.
By pressing “ ” or “ ” button you may select one of
these options: COOL, WARM, NORMAL.
Note: Colour Temperatures transitions are become
slowly.
SUBTITLE
This mode is used to display 4:3 pictures using the full
surface of the screen leaving the sub-titles visible. Use
the “ ” or “ ” buttons to increase or decrease the
compression at the bottom of the screen.
Setting Zoom
You can change the screen size according to the pic-
ture aspect ratio. Select the optimum one from the fol-
lowing ZOOM modes.
ZOOM
AUTO:
The picture is enlarged to 16:9 format.This mode is
recommended when displaying pictures which have
black bands at the top and bottom (letterbox format).
When a WSS (Wide Screen Signalling) signal,
which shows the aspect ratio of the picture, is includ-
ed in the broadcast signal or the signal from an exter-
nal device, the TV automatically changes the ZOOM
mode to 16:9 mode or 4:3 mode according to the
WSS signal.
Use the “ ” or “ ” buttons if you wish to compress
and move the image vertically to view the top or bot-
tom of the picture.
• When the AUTO mode does not function correctly
due to poor WSS signal quality or when you want to
change the ZOOM mode, change to another ZOOM
mode manually.
Using the different screen formats
Select the ZOOM mode:
Press the “ ” or “ ” button to select the different
modes: 4:3, 16:9, CINEMA, SUBTITLE and ZOOM.
Press the “ ” or “ ” button to select a ZOOM mode.
You can also access these settings with “ ” button.
4:3
The picture is reproduced in 4:3 format and a black
band is displayed on either side of the picture.The pic-
ture may be progressively enlarged using the “ ” or
“
” buttons.
ENGLISH - 13 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A3K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the visible area of the picture:
Child Lock
If subtitles or the top (or bottom) of the picture are cut
off, you can adjust the visible area of the picture manu-
ally.
You can use this feature to prevent children turning on
TV or changing programs or adjustments etc. without
remote control.
1. Press “ ” button once.
The Child Lock feature can be set by “ ” or “ ” but-
ton to either ON or OFF. When OFF is selected, there
will be no difference in the operation of your TV. When
ON is selected, the TV can only be controlled by the
remote control handset. In this case, the front panel
buttons (except the Power On/Off button) will not
work.
The ZOOM mode indicator appears. The ZOOM
mode will not be changed.
2. While it is displayed, press “ ” or “ ” buttons to
change the position of the picture.
• You can not adjust the visible area in 4:3 or 16:9
mode.
If Child Lock is ON, when one of the front panel but-
tons (except power button) is pressed, “CHILD LOCK”
OSD is seen on the screen.
Selecting Menu Language
Menu language can be selected by pressing “ ” or
“ ” button on Language item.
To Store the Settings
• Press “ ” or “ ” button on STORE option to store
Picture menu settings.
EXT-2 Output
From EXT-2 Output, either TV, EXT-1 or F-AV can be
given. TV, EXT-1 or F-AV can be selected by pressing
“ ” or “ ” button on “EXT-2 OUTPUT”.
Feature Menu
• To enter the Feature menu directly, press the “YEL-
LOW” button, or
• Press "M" button, now you are in MENU. In the
MENU, select Feature using “ ” or “ ” button.
To Store Settings
Then enter the Feature menu pressing “ ” or “ ”
button.
In Feature menu all settings are stored automatically.
Installation Menu
• To enter the Install menu directly, press the BLUE
button, or
• Press “M” button, now you are in MENU. In the
MENU, select “Install” using “ ” or “ ” button. Then
enter the Install menu pressing “ ” or “ ” button.
Sleep Timer
As you enter the Feature menu, Sleep Timer will be
the first selected option. Use “ ” or “ ” button to
change the Sleep Timer values between OFF, 10, 20,
30, ......, 110 and 120.
If sleep timer is activated, at the end of the selected
the time, the TV goes automatically to stand-by mode.
ENGLISH - 14 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A4K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
1.Selecting Programme
6.Selecting Search
To select programme number, you can use “ ” or “ ” To start the search process, press “ ” button for for-
button, Digit Buttons or The Double Digit button with
digit buttons.
ward search or “ ” button for backward search.
Search item bar blinks during search process, up to
the process is stopped or signal is found. To stop the
search process “ ” or “ ” button must be pressed
again.
7.To Store Settings
Press “ ” or “ ” button on STORE option to store In-
stall menu settings.
2.Selecting Band
BAND, can be selected either,
Program Menu
• “C” or “S” by “ ” or “ ” button.
For band C,
• To enter Program menu directly, press the "
ton, or
" but-
01 - 83, WEST EUROPE.
01 - 12, 21 - 69, EAST EUROPE .
01 - 17, 21 - 73, UK.
• Press “M” button, now you are in MENU. In the
MENU, select “Program” using “ ” or “ ” button.
Then enter the Program menu pressing “ ” or “ ”
button.
01 - 76, FRANCE.
04 - 09, FRANCE 2.
For band S,
01 - 41, for all channel tables.
3.Standard
Moving cursor to four direction you can reach 30 pro-
grammes in the same page. By scrolling the pages up
or down by pressing the navigation buttons you can
select all the programmes in TV mode (except the AV
mode).
The “STANDARD” setting is fixed to “B/G”. You cannot
change this item's setting.
4.Selecting Colour System
This item is used to change the colour system. If the
picture is not clear or no colour appears, select the
correct colour system to display the picture normally.
In menus, “ ” or “ ” buttons are working like "Direc-
tion Up" and "Direction Down".
By cursor action, programme selection is done auto-
matically. Selected programme is displayed with
“HIGHLIGHTED” characters.
When the TV is in TV mode; by pressing “ ” or “ ”
button you may select one of these options: PAL, SE-
CAM. When the TV is in AV mode; you may select
one of these options: AUTO, PAL, SECAM, NTSC
3.58, NTSC 4.43.
Programme Number is between 00 and 99. Pro-
gramme Name has a name string with 4 characters.
After autostore process the Programme Names are
set to:
• Channel search "C01" or "S01" (band and channel
number), as default.
At the bottom of the menu there is a programme sort
functions section. Each function is activated by color
button. NAME allows changing the programme name.
By DELETE you can delete programmes that you de-
cided. INSERT section is for inserting programmes
into another programme spaces. By selecting AUTO-
STORE section, Autostore menu will be available.
5.Selecting Fine Tuning
You can use the Fine Tuning process for fine adjust-
ment (after coarse adjustment), if you are not happy
about the image on the screen.
Use “ ” or “ ” button on FINE TUNING item, until
getting the best image on the screen.
To change the name of a decided programme, that
programme is selected and pressed to the RED button
(NAME). First letter of the selected NAME is displayed
with HIGHLIGHTED character. To change that letter
In Channel option, normally the Fine Tuning cursor is
placed at the middle on the slider, and this is indicated
with the two reciprocal arrows.
“
” or “ ” button can be used, and to select the oth-
er letters, “ ” or “ ” button can be used. If the cursor
is at the last letter of the Programme Name, pressing
“ ” button moves the cursor at the beginning. On the
ENGLISH - 15 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A5K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
contrary, if the cursor is at the beginning of the Pro- If you want to make A.P.S. any other time:
gramme Name, pressing “ ” button moves the cursor
at the end.
• Press “M” button, now you are in MENU.
• Select “Program” menu using “ ” or “ ” button.
• Press “ ” or “ ” button to enter the “Program”
menu.
• In the “Program” menu enter AUTOSTORE menu
by pressing BLUE button. Here you can run A.P.S. (
Automatic Programming System). A.P.S. automati-
cally programmes your TV , according to the trans-
mission of programme systems in your area.
A warning message will appear on the screen as be-
low :
After changing the name by pressing the RED button
(STORE) it is stored. After activating the name pro-
cess the “INSERT”, “DELETE” and “AUTOSTORE”
processes will be inactive and "CANCEL" and
“STORE” options are invalid. "CANCEL" option can-
cels the name process, if the new name do not want
to be stored.
• If you want to Continue, by pressing “ ” or “ ” but-
ton start the A.P.S..
When it is pressed to GREEN button (INSERT),
"NAME", "AUTOSTORE" and "DELETE" functions are
erased, the selected programme (A) is displayed with
green characters. From now on, the automatic selec-
tion is canceled. Cursors moves are indicated with
“HIGHLIGHTED” characters. With navigation buttons,
the decided program space (B) can be selected and
by pressing the green button again inserting is oc-
curred to that space (B).
• When you start A.P.S. the below menu will appear
on the screen.
After A.P.S. is finalized, a rank list will appear on the
screen. In the rank list you will see the programme
numbers and names, assigned to the programmes.
First the programme with programme number 1 will be
It should be thought that Prog-00 is the lowest pro-
gramme (like Prog-100). If any programme is inserted
to Prog-00, the programmes under that programme
space shift one up, and Prog-99 is adjusted to the first
frequency value of VHF1 (40 MHz).
displayed with “HIGHLIGHTED” characters. Using “
”
or “ ” or “ ” or “ ” buttons you can move the high-
lighted number and then display the programme corre-
sponding to the highlighted number.
If Prog-00 is inserted to any programme space, all the
programmes under that space shift one down and
Prog-99 is erased, and Prog-00 is adjusted to the first
frequency value of VHF1 (40 MHz).
If you do not accept the correspondence between pro-
gramme numbers and names and want to change
them, press “M” button and then BLUE button, so that
you enter the Installation menu.
"CANCEL" function cancels the activated "INSERT"
process.
Other Features
For "DELETE" process it is pressed to yellow button,
(“NAME”, “INSERT” and “AUTOSTORE” functions are
inactive). The selected programme is displayed with
yellow characters. Pressing yellow button again eras-
es the selected programme from the programme list,
and the programmes below shift one up. Prog-00 is
adjusted to the first frequency value of VHF1 (40
MHz). Pressing blue button cancels the activated “DE-
LETE” process.
1) TV Status
Programme Number, Programme Name (or AV)
and Sound Indicator are displayed on the upper left
of the screen. They are displayed after programme
change during 3 seconds.
Programme Number
3ꢀꢁꢂ
Programme Name (4 characters)
35ꢀꢁ
To enter Autostore menu, press to the blue button. To
learn the features of this function see "AUTOSTORE"
below.
These OSD’s are displayed when a new programme is
entered by digit button, by pressing “P<P” button, or
by “ ” or “ ” button, or by “
” button.
Autostore
2) Programme Swap (P<P)
(A.P.S. (Automatic Programming System))
This button is used to reenter to the preceding entered
programme again. Pressing “P<P” consecutively al-
lows to swap into two last entered programmes.
A.P.S. automatically programmes your TV, according
to the transmission of programme systems in your
area.
ENGLISH - 16 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A6K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Double-digit (- -)
7) Blue Background During No-Signal
This OSD is displayed when the "Double-Digit" button In case, no valid signal is detected (in TV or AV mode)
pressed in place of the programme number indicator.
Blue Background is activated. During search process
Blue Background is not active. But instead of it there
is another feature given; the semi-transparent menu
background is made blue.
After then, in order to enter a programme it must be
pressed to two digit consecutively. When it is late to
press any digit button this function will be ignored and
the display will be erased. In the same way it must not
be late to press any digit button after entering the first
digit. The limit of the delay time is 3 seconds.
8) Mute Indicator
It is placed in the upper middle of the screen when en-
abled, and it stays there until it is disabled.
To cancel mute, there is two alternative; the first one is
pressing to " " button, thus volume is set to the pre-
ceding value, and the second one is increasing the vol-
ume level, thus it starts at the minimum level to in-
crease. By decreasing the volume level in mute state,
mute will not be ignored, only the volume level will de-
crease. If mute canceled after decreasing the volume
level, the volume will valid with the decreased level.
4) Personal Preferences (PP)
9) Volume Bar
All the preset values will be restored, when pressing
"PP".
It is displayed in the lower middle of the screen. When
a volume command is received (pressing “-
” or
“
+” by Remote Control or Front panel) and no
5) Sound Indicator
menu is active, it stays on the screen for 3 seconds,
after the last volume command or until another com-
mand is received in between.
This is a stereo option. The alternatives of the indicator
are Mono, Stereo, Dual-I and Dual-II. This indicator is
displayed under the programme number indicator on
the screen. "I-II" button is used to select Mono, Ste-
reo, Dual-I or Dual-II.
10) AV Modes
In Mono broadcast or in forced-mono (for stereo broad-
cast).
By pressing the “
“ button you can switch your TV
to AV modes (except being in Teletext). Pressing this
button will switch the TV in one of the optional AV
modes: EXT-1, RGB, YCbCr and F-AV (Front AV).
EXT-1 supports the RGB mode.
In Stereo broadcast.
If dual broadcast detected. Dual-I is selected in default
and also can be selected after Dual-II by Remote Con-
trol.
In order to quit the AV mode press the “ ”, digit but-
tons or “-P/CH” or “P/CH+”.
'8$/ꢀ,
If Dual-II selected by Remote Control.
6) Picture Mode
The picture mode OSD is displayed below the sound
indicator, by TV Status OSD’s. According to the WSS
data, inside of the OSD box “4:3” , “16:9”, “CINEMA”,
“SUBTITLE”, “ZOOM” or “AUTO” is written.
By pressing “ ” (TXT_UPDATE) button (if Teletext is
not active) the picture mode can be switched into 4:3,
16:9, CINEMA, SUBTITLE, ZOOM or AUTO Mode.
ENGLISH - 17 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A7K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
5) Searching for a page while watching TV
Teletext
• While Teletext Mode is on, pressing “ ” will change
the mode to TV, one more press to “ ” will change
the mode from TV to the latest Teletext page we left.
In the TV mode enter a page number using digit
keys. As you enter digits first line of teletext page will
appear on top screen and will remain there until the
requested page is found. Then teletext line will be re-
placed by page number to indicate that page has
been found. Now you can display this teletext page
pressing “ ” button.
Teletext is an information system that displays text on
your TV screen. Using the Teletext information system
you can view a page of information on a subject that is
available in the list of contents (index).
On screen display is not available in text mode.
Contrast, brightness or colour control is not available,
but volume control is available in text mode.
1) To operate Teletext
• Select a TV station on which Teletext is being trans-
mitted.
6) To Select Double Height Text
• Press (TELETEXT) “ ” button. Usually the list of
contents (index) is displayed on the screen.
• Press “ ” button for the upper half of the informa-
tion page to be displayed in double height text.
• Press “ ” button again for the lower half of the infor-
mation page to be displayed in double height text.
• Press “ ” button once more for the full page of nor-
mal height text.
7) To Reveal “concealed” Information
• Pressing “ ” button once will reveal answers on a
quiz or games page.
• Pressing “ ” button again will conceal the revealed
answers.
2) To select a page of Teletext
• Press the appropriate digit buttons for the required
Teletext page number.
8) To Stop Automatic Page Change
The teletext page you have selected may contain
more information than what is on the screen; the rest
of the information will be displayed after a period of
time.
The selected page number is displayed at the top left
corner of the screen. The Teletext page counter
searches until the selected page number is located,
so that the desired page is displayed on the screen.
• Press “ ” button to stop the automatic page chan-
ge.
• Press “ ” button to move the Teletext screen for-
ward one page at a time.
• Press “ ” button again to allow the next page to be
displayed.
• Press “ ” button to move the Teletext screen back-
ward one page at a time.
9) To Select a Subcode Page
3) To Select Index Page
Subcode pages are subsections of long Teletext pag-
es that can only be displayed on the screen one sec-
tion at a time.
• To select the page number of the index (generally
page 100), press “ ” button.
• Select the required Teletext page.
• Press “ ” button.
4) To Select Teletext with a TV Programme
• Press “ ” button. The text is now superimposed
over the programme on the screen.
• Select the required subcode page number by press-
ing four digit buttons (e.g. 0001).
• Press “ ” button again to return to the Teletext
page.
ENGLISH - 18 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A8K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
• If the selected subcode page is not displayed in a
short time, press “ ” button. TV programme will be
displayed on the screen.
Connect Peripheral Equipment
There is a wide range of audio and video equipment
that can be connected to your TV.
• Teletext page number will be displayed on the upper
left corner of the screen when the selected page is
found.
The following connection diagrams show you where
the different equipment should be connected at the
back or the front side of the TV.
• Press “ ” button to display the selected Teletext
page.
1) Via the Euroconnector
Your TV set has two Euroconnector sockets. If you
want to connect peripherals (e.g. video, decoder, etc.)
which have Euroconnectors to your TV, use optional
EXT.1 or EXT.2 inputs.
10 To exit Teletext
• Press “ ” button. The screen will switch to TV
mode.
If an external device is connected via EXT.1 Eurocon-
nector socket TV is switched to AV mode automatical-
ly. If the signal is RGB then the RGB OSD indicator is
displayed on the screen.
11) To Display the Time
• While watching a TV programme with Teletext trans-
mission press “ ” button. The current time informa-
tion, captured from Teletext will be displayed at the
upper right of the screen.
2) YCbCr Mode
• If the programme being watched does not have Tele-
text transmission, no iformation will be displayed.
This mode is only used for the equipment which have
YCbCr signal at their output. You can watch only YCb-
Cr signal at this mode. RGB, Y/C or CVBS signals
can not be watched.
12) Fastext
Your CTV supports the 7 page Teletext system. When
the page number of any of the 7 pages in memory is
entered, the system will not search for the requested
page; instead it will display the page automatically.
3) Via Ant Input
If you want to connect to your TV, peripherals like vid-
eo recorders or decoders, but the device you want to
connect does not have Euroconnector, you should
connect it to the ANT input of your TV set.
• Press “ ” button to move the Teletext screen for-
ward one page at a time.
If the VCR is connected via antenna input it is sug-
gested to use the Programme 0.
• Press “ ” button to move the Teletext screen back-
ward one page at a time.
4) Decoder
For Fastext
Cable TV offers you a wide choice of programs. Most
of them are free, others are to be paid for by the view-
er. This means that you will need to subscribe to the
broadcasting organisation whose programmes you
wish to receive. This organisation will supply you a
corresponding decoder unit to allow the programmes
to be unscrambled.
The subject-heading for the information may have a
particular colour.
• Press an appropriate RED, GREEN, YELLOW or
BLUE button in order to reach the relevant page
quickly.
For further information ask your dealer. See also the
booklet supplied with your decoder.
a) Connect a decoder with an aerial socket
to the TV
• Connect the aerial cable.
b) Connect a decoder without an aerial
socket to the TV
• Connect the decoder to your TV with a eurocable to
EXT.1. When your decoder has a Euroconnector you
can obtain better picture quality if you connect a
eurocable to EXTERNAL.
5) TV and Video Recorder
• Connect the aerial cables.
Better picture quality can be obtained if you also con-
nect a eurocable to EXTERNAL sockets.
ENGLISH - 19 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-1A9K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
6) Playback NTSC
11) Connecting Headphones
Connect NTSC VCR player to Euroconnector at the Use the stereo headphone socket on the lower right
back of the TV.
side of your TV, to connect headphones.
Connect NTSC VCR player to RCA Jack at the front of
the TV.
Then, press “
“ button to select (EXT-1, RGB, YCb-
Cr and F-AV).
7) Copy Facility
Source selection for VCR recording.
• Select Features Menu in the MENU.
• Select EXT-2 OUTPUT source pressing “ ” or “ ”
button.
8) Search for and store the test signal of the
video recorder
• Unplug the aerial cable from the aerial socket “ANT”
of your video recorder.
• Switch on your TV and put the video recorder on the
test signal. (See the handbook for your video re-
corder.)
• Enter the Tuning menu via the Install menu.
• Search for the test signal of your video recorder in
the same way as you searched for and stored the TV
signals. See Tuning, Search and Store TV channels.
Store the test signal under programme number 0.
• Replace the aerial cable in the aerial socket “ANT” of
your video recorder once you have stored the test
signal.
9) Camera and Camcorder
To connect to Front-AV input (F-AV):
Connect your camera or camcorder at the front side of
your TV.
• Connect your equipment to the TV via VIDEO (yel-
low), AUDIO R (red) and AUDIO L (white) inputs. You
should connect the jacks to the input in the same
colour.
10) Connect the decoder to the video
recorder
Some video recorders have a special euroconnector for
decoder.
• Connect a eurocable to the euroconnector of your
decoder and to the special euroconnector of your
video recorder. See also the handbook of your video
recorder.
• To connect your video recorder to the TV, see TV and
Video Recorder section.
If you want to connect more equipment to your TV,
consult your dealer.
ENGLISH - 20 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-2A0K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect Peripheral Equipment
CAMERA
AUDIO
HEADPHONE
VIDEO
DECODER
FOR SATELLITE RECEIVER
Antenna Connections
2XWGRRUꢀ$QWHQQDꢀ&RQQHFWLRQV
ENGLISH - 21 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-2A1K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Tips
Care of the Screen
TV BROADCASTING
Clean the screen with a slightly damp, soft cloth. Do
not use abrasive solvents as they may damage the TV
screen coating layer.
PAL B/G
RECEIVING CHANNELS
VHF (BANDI/III)
Poor Picture
Have you selected the correct TV system? Is your TV
set or house aerial located too close to the loudspeak-
ers, non-earthed audio equipment or neon lights, etc.?
UHF (BAND U)
Hyperband
CABLE-TV (S1-S20 / S21-41)
Mountains or high buildings can cause double pictures
or ghost images. Sometimes you can improve the pic-
ture quality by changing the direction of the aerial.
NUMBER OF PRESET CHANNELS
Is the picture or Teletext unrecognizable? Check if you 100
have entered the correct frequency.
The picture quality may degrade when two peripherals
are connected to the TV at the same time. In such a
case, disconnect one of the peripherals.
CHANNEL INDICATOR
OSD (ON SCREEN DISPLAY)
No Picture
RF AERIAL INPUT
Is the aerial connected properly? Are the plugs con-
nected tightly to the aerial socket? Is the aerial cable
damaged? Are suitable plugs used to connect the aeri-
al? If you are in doubt, consult your dealer.
75 Ohm Unbalanced
OPERATING VOLTAGE
240V AC, 50 Hz.
No Picture means that your TV is not receiving any
transmission. Have you pressed the correct buttons
on the remote control? Try once more.
POWER CONSUMPTION (W) (max)
140 Watt
Sound
You can not hear any sound. Did you perhaps interrupt
AUDIO OUTPUT
the sound, pressing “ ” button? Are external speakers
connected to the TV?
German + Nicam Stereo
Sound is coming from only one of the speakers. Is the
balance set to one direction extreme? See SOUND
menu.
PICTURE TUBE
28” 16:9
Remote Control
DIMENSIONS (DxLxH) (mm)
Your TV no longer responds to the remote control.
Press the “
” button on the remote control once
',0(16,216
more. Perhaps the batteries are exhausted. If so you
can still use the local buttons at the front of your TV.
'
/
+
: HLJKWꢀꢁNJꢂ
ꢀꢁꢁ
ꢂꢃꢄ
ꢅꢂꢀ
ꢆꢇ
Have you selected the wrong menu? Press “ ” but-
ton to return to TV mode or press “M” button to return
to the previous menu.
No solution
Switch your TV set off and on. If this does not work,
call the service personnel; never attempt to repair it
yourself.
ENGLISH - 22 -
EU2845ST&2845W-MAV-1541-ENG-STEREO-2A2K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
EU2845ST&2845W-MAV-1541-ENG-STEREO-2A3K45.p65
09.09.2003, 10:54
Download from Www.Somanuals.com. All Manuals Search And Download.
|