9A10001300
Z
CR-H250
CD/Receiver Micro-System
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Compact Disc
Discs which can be played on this unit:
< Discs should be returned to their cases after use to
avoid dust and scratches that could cause the laser
pickup to ‘skip’.
• Conventional audio CDs bearing the CD-DA logo
on the label:
< Do not expose discs to direct sunlight or high
humidity and temperature for extended periods.
Long exposure to high temperatures will warp the
disc.
• Properly finalized CD-R and CD-RW discs
< Do not play any disc that is warped, deformed or
damaged. Playing such discs may cause irreparable
harm to the playing mechanisms.
Note:
< Depending on the quality of the disc and/or the
condition of the recording, some CD-R/CD-RW
discs may not be playable.
< CD-R and CD-RW discs are more sensitive to the
effects of heat and ultraviolet rays than ordinary
CDs. It is important that they are not stored in a
location where direct sunlight will fall on them, and
which is away from sources of heat such as
radiators or heat-generating electrical devices.
< Copy-protected discs and other discs which do not
conform to the CD standard may not play back
correctly in this player. If you use such discs in this
unit, TEAC Corporation and its subsidiaries cannot
be responsible for any consequences or guarantee
the quality of reproduction. If you experience
problems with such non-standard discs, you should
contact the producers of the disc.
< Printable CD-R and CD-RW discs aren’t
recommended, as the label side might be sticky and
damage the unit.
< Do not stick papers or protective sheets on the
discs and do not use any protective coating spray.
< Always place the disc on the disc tray with the label
side uppermost. (Compact discs can be played or
recorded only on one side.)
< Use a soft oil-based felt-tipped pen to write the
information on the label side. Never use a ball-point
or hard-tipped pen, as this may cause damage to
the recorded side.
< To remove a disc from its storage case, press down
on the center of the case and lift the disc out,
holding it carefully by the edges.
< Never use a stabilizer. Using commercially available
CD stabilizers with this unit will damage the
mechanisms and cause them to malfunction.
< Do not use irregular shape CDs (octagonal, heart
shaped, business card size, etc.). CDs of this sort
can damage the unit:
How to remove the disc
How to hold the disc
< Should the disc become dirty, wipe the surface
radially (from the center hole outward towards the
outer edge) with a soft, dry cloth:
< If you are in any doubt as to the care and handling
of a CD-R/CD-RW disc, read the precautions
supplied with the disc, or contact the disc
manufacturer directly.
< Never use such chemicals as record sprays,
antistatic sprays or fluid, benzine or thinner to clean
the discs. Such chemicals will do irreparable
damage to the disc’s plastic surface.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
A
Speaker Connections
Caution:
< To avoid damaging the speakers by inputting a
sudden high-level signal, be sure to switch the
power off before connecting the speakers.
< Check the impedance of your speakers. Connect
speaker with an impedance of 6 ohms or more.
< The amplifier’s red speaker terminals are the +
(positive) terminals and the black terminals are the
_ (negative) terminals.
The + side of the speaker cable is marked to
make it distinguishable from the negative side of
the cable. Connect this marked side to the red +
terminal and the unmarked side to the black _
terminal.
B
A
< Prepare the speaker cords for connection by
stripping off approximately 10 mm or less (no
more as this could cause a short-circuit) of the
outer insulation. Twist the wires tightly together
to avoid tangles:
SPEAKER
LINE
IN
How to connect
1.Turn the terminal cap counterclockwise to loosen
it. The speaker terminal caps cannot be fully
removed from the base.
SUBWOOFER
2.Insert the wire into the terminal fully and turn the
terminal cap clockwise to securely connect it:
CAUTION
< Turn off the power of all the equipment before
making connections.
< Read instructions of each component you intend
to use with this unit.
< Be sure to insert each plug securely. To prevent
hum and noise, do not bundle the connection
cords with the power cord or speaker cord.
3.Make sure it is fastened firm by pulling the cable
lightly.
B
SUBWOOFER OUT jack
Connect a commercially available powered
subwoofer.
< Subwoofer output will not be cut off, when the
headphone jack is inserted.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR, DVD, etc.
MD, CD-R, etc.
Cassette Deck (R-H300mk@)
DIGITAL IN LINE
(OPTICAL) OUT
REMOTE
LINE
OUT
LINE
IN
LINE
OUT
LINE
IN
CONTROL
R
L
L
R
L
R
L
R
L
R
E
C
D
F
C
E
F
TAPE/AUX jacks
Make sure to connect:
AC Power Cord
Plug this AC power cord into an AC wall socket.
white plug q white jack (L: left channel)
red plug q red jack (R: right channel)
REMOTE CONTROL jack
< Be sure to insert each plug securely. To prevent
hum and noise, do not bundle the connection
cords with the power cord or speaker cord.
< You can use the system remote control unit RC-
956 (provided with this unit) to operate TEAC R-
H300mk@.
Connect the REMOTE CONTROL jack (A or B) to
the REMOTE CONTROL jack (A or B) of R-
H300mk@ with the remote control connection
cord.
D
DIGITAL OUT terminal
Connect the component with an optical cable.
DIGITAL OUT w DIGITAL IN (MD, etc.)
< When inserting the plug of the optical cable, the
protective shutter of the terminal will open and
you should hear it click into position when fully
inserted. Be careful that you do not force the
plug, because this could result in damage to the
protective shutter, the cable, or the unit itself.
Note:
The remote control connection cord is not
provided with this unit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas (AM/FM)
AM Indoor Loop Antenna
FM Indoor Antenna
The high-performance AM loop antenna provided
with this unit is sufficient for good reception in
most areas.
To stand the loop antenna on a surface, fix the
claw to the slot in the antenna base.
Connect the lead-type FM antenna to the FM 75Ω
socket, extend the lead and tune the tuner to your
favorite station (see page 28). Adjust the antenna
in a suitable location like a window frame or wall
until the reception is best and then affix the
antenna in that position using thumb tacks, push
pins or any other suitable means.
Connect the loop antenna’s wires to the AM
antenna terminals.
Place the antenna on a shelf or hang it on a
window frame, etc., in the direction which gives
the best reception. Keep all other wires such as
power cords, speaker wires or interconnect wires as
far away as possible from the antenna.
AM Outdoor
Antenna
FM Outdoor Antenna
In an area where FM signals are weak, it will be
necessary to use an outdoor FM antenna.
Generally, a 3-element antenna will be sufficient; if
you live in an area where the FM signals are
particularly weak, it may be necessary to use one
with 5 or more elements.
Make sure to connect
the black wire to the
GND terminal.
< Disconnect the FM indoor antenna when using an
outdoor antenna.
< If the AM loop antenna provided does not deliver
sufficient reception (often due to being too far
from the transmitter or in a concrete building, etc.),
it may be necessary to use an outdoor AM antenna.
Use either a high quality commercial AM antenna
or, if not available, an insulated wire more than 5
m long, strip one end, and connect this to the
terminal as shown.
The antenna wire should be strung outdoors or
indoors near a window. For better reception,
connect the GND terminal to a reliable ground.
Note:
Even when using an outdoor AM antenna, do not
disconnect the AM loop antenna.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas (DAB)
DAB Indoor Antenna
DAB Outdoor Antenna
Connect the T-type DAB antenna to the DAB
socket, extend the lead vertically and attach it to a
window frame or wall with thumbtacks, or the like,
where reception is best.
In an area where DAB signals are weak, it will be
necessary to use an outdoor DAB antenna. There
are two main types available.
Dipole:
For use in marginal signal areas. This type of
antenna is omnidirectional and should increase the
strength of all DAB stations being received.
Multi-element antenna:
Also for use in marginal or poor signal areas. This
type of antenna is directional and has high gain.
This antenna needs to be pointed at the transmitter
you want to listen to.
Multi-element
Dipole
< You can check the antenna adjustment or
positioning for the best reception by viewing the
signal strength on the display.
The signal strength is displayed as a bar graph by
pressing the ENTER button once.
< It is possible to use a TV or FM antenna with your
DAB tuner as this is normally mounted externally.
This may give a stronger signal than a simple
internal antenna, however it would not be tuned
specifically for DAB reception.
You would need to change the plug on your TV/FM
antenna to an F type, and it may also be necessary
to use a signal booster to enhance the signal.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Each Control 1
A
B
C
D
E
Q
P
O
N
M
L
K
J
I
H
G
F
A
F
Remote Sensor
SKIP (.
/
/), TUNING, PRESET, TIME
m ,
When operating the remote control unit, point it
towards the remote sensor.
In CD mode, use these buttons to skip tracks.
In TUNER mode, use these buttons to tune in
stations or select the preset stations.
While setting the clock or the timer, use these
buttons to adjust the time.
B
C
D
Display
Disc tray
G
STOP (H), INFO, RDS MODE, CLEAR
In CD mode, use this button to stop playback.
In DAB mode, this button is used to change the
text content on the second line of the display, to
show DLS (Dynamic Label Segment, info text
supplied by each radio station), Programme type
(classification given by the radio station ie: Pop
music or Rock), Multiplex name (name of multiplex
broadcaster), Time & date, Bitrate, or Channel and
frequency.
In FM mode, this button is used to select the RDS
mode.
Also use this button to cancel the entering or
modes.
OPEN/CLOSE (L), AUTO TUNING
In CD mode, use this button to open and close the
disc tray.
In DAB mode, press this button to activate auto
location of all available DAB services. Press once for
UK services or, hold for longer than 2 seconds to
activate international search.
E
VOLUME, SELECT
Turn this knob to adjust the volume.
Turn this knob to adjust the tone, balance and
dimmer together with the TONE/BAL/DIMMER
button.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
H
POWER
PAUSE (J), FUNCTION, FM MODE
Press this button to turn the unit on or standby.
The standby indicator lights when the unit is in the
standby mode. When the unit is turned on, it goes
off.
In CD mode, use this button to pause playback.
In DAB mode, activates features such as station
order, manual tune, DRC value, SW version
indication, signal error rate. It is also possible to
‘tidy’ the station list to remove stations which are in
the memory but have no service provided.
In FM mode, use this button to select stereo or
monaural.
The equipment draws nominal non-operating
power from the AC outlet with its POWER switch
in the STANDBY position.
If the R-H300mk
with a remote control cord, you can switch
ON/standby both the CR-H250 and the R-H300mk
by pressing the POWER button of the CR-H250.
@
is connected to the CR-H250
I
PLAY (y), BAND
In CD mode, use this button to start playback.
In TUNER mode, use this button to select FM, AM
or DAB.
@
J
TUNING MODE, ENTER/SET
In FM or AM mode, use this button to select the
tuning mode.
In DAB mode, use this button to enter the
selection.
While setting the timer or the clock, use this button
to set the time.
K
PROGRAM, MEMORY
In CD mode, use this button to enter the program
mode. In program mode, use this button to enter
the selection.
In TUNER mode, use this button to memory the
station manually.
L
TIMER
Use this button to turn on or off the timer function.
M
N
TIME MODE
Use this button to adjust clock and to set timer.
TONE, BAL, DIMMER
Use this button to adjust the tone, balance and
dimmer together with the VOLUME/SELECT knob.
O
P
Input selector
Use these buttons to select a source.
PHONES
For private listening, insert the headphones plug
into this jack, and adjust the volume by turning the
VOLUME/SELECT knob.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Each Control 2
d
INFO, RDS
In DAB mode, this button is used to change the
text content on the second line of the display, to
show DLS (Dynamic Label Segment, info text
supplied by each radio station), Programme type
(classification given by the radio station ie: Pop
music or Rock), Multiplex name (name of multiplex
broadcaster), Time & date, Bitrate, or Channel and
frequency.
a
k
l
m
b
c
n
r
o
p
d
g
In FM mode, this button is used to select the RDS
mode.
e
f
q
s
e
SEARCH
(
/
)
m ,
During playback of CD, use these buttons to search
the part you want to listen to.
t
u
h
i
f
SHUFFLE
v
In CD mode, use this button to enter the shuffle
playback mode.
w
y
x
z
g
STOP
j
In CD mode, use this button to stop playback.
h
i
DIMMER
Use this button to dim the display.
MUTING
Use this button to mute the sound.
j
TIME
In CD mode, use this button to change the time
display.
a
b
POWER ON
Press this button to turn the unit on.
k
l
STANDBY
AUTO TUNE
Press this button to turn the unit to stanby mode.
In DAB mode, press this button to activate auto
location of all available DAB services. Press once for
UK services or, hold for longer than 2 seconds to
activate international search.
Buttons for the operation of TEAC R-H300mk
@
(TAPE).
c
m
FUNCTION, FM MODE
PRESET CALL
In DAB mode, activates features such as station
order, manual tune, DRC value, SW version
indication, signal error rate. It is also possible to
‘tidy’ the station list to remove stations which are in
the memory but have no service provided.
In FM mode, use this button to select stereo or
monaural.
In TUNER mode, use these buttons to select the
preset stations.
n
ENTER
In DAB mode, use this button to enter the
selection.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Unit
o
BAND
The provided Remote Control Unit allows the unit
to be operated from a distance.
When operating the remote control unit, point it
towards the REMOTE SENSOR on the front panel of
the unit.
In TUNER mode, use this button to select FM, AM
or DAB.
p
q
SKIP (.//)
In CD mode, use these buttons to skip tracks.
< Even if the remote control unit is operated within
the effective range, remote control operation may
be impossible if there are any obstacles between
the unit and the remote control.
PLAY (y)
In CD mode, use this button to start playback.
r
s
PAUSE (J)
< If the remote control unit is operated near other
appliances which generate infrared rays, or if other
remote control devices using infrared rays are used
near the unit, it may operate incorrectly.
Conversely, the other appliances may operate
incorrectly.
In CD mode, use this button to pause playback
Input selector
Use these buttons to select a sauce.
t
SLEEP
Battery Installation
Use this button to set the sleep timer.
1. Remove the battery compartment cover.
2. Insert two ‘AAA’ dry batteries. Make sure that the
batteries are inserted with their positive ‘+’ and
negative ‘_’ poles positioned correctly.
3. Close the cover.
u
v
VOLUME
Use these buttons to adjust the volume.
Numeric buttons
Use these buttons to select a track number or a
preset channel.
Press the CD or TUNER button to select the mode,
and then press the numeric buttons.
Battery Replacement
For instance, to select track number 35, first press
the CD button, and then press ‘3’ and ‘5’.
To select numbers less than 10, press ‘0’ and then
the number. As an example, to select number 5,
press ‘0’ and ‘5’. (Optionally, you may press just
the number ‘5’ and then wait a few seconds.)
If the distance required between the remote control
unit and main unit decreases, the batteries are
exhausted. In this case replace the batteries with
new ones.
Precautions concerning batteries
< Be sure to insert the batteries with correct positive
‘+’ and negative ‘_’ polarities.
< Use batteries of the same type. Never use different
types of batteries together.
w
PROGRAM
In CD mode, use this button to enter the program
mode. In program mode, use this button to enter
the selection.
< Rechargeable and non-rechargeable batteries can
be used. Refer to the precautions on their labels.
< When the remote control unit is not to be used for
a long time (more than a month), remove the
batteries from the remote control unit to prevent
them from leaking. If they leak, wipe away the
liquid inside the battery compartment and replace
the batteries with new ones.
x
y
CLEAR
Use this button to cancel the entering or modes.
REPEAT A-B
Use this button to set the point for A-B repeat.
z
REPEAT 1/ALL
< Do not heat or disassemble batteries and never
dispose of old batteries by throwing them in a fire.
Use this button to select the repeat mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
D
Muting
C
To cut the sound temporarily, press the MUTING
button. Press any button to restore the sound.
A B
A
How to select CD/TAPE
Every time the CD/TAPE button is pressed, the
mode is changed as follows:
E
Dimmer (remote control)
Press the DIMMER button to dim the display.
Press the button again to cancel the dimmer
function.
CD
TAPE
B
How to select TUNER/AUX 1/2
Every time the TUNER/AUX 1/2 button is pressed,
the mode is changed as follows:
< This function will be cancelled when the unit is
turned off.
< If the R-H300mk@ is connected to this unit with a
remote control cord, the display of both will be
dimmed.
TUNER AUX 1
AUX 2
F
Listening through headphones
Or press the CD, TAPE, AUX 1/2 or TUNER button
on the remote control unit to select the source
directly.
Insert the headphone plug into the PHONES jack,
and adjust the volume. The sound from speakers
will be cut off.
C
Adjust the volume
To protect speakers from a sudden high-level
signal, gradually turn up the volume to the required
level with the VOLUME knob.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2
1
Bass control
How to adjust TONE/BALANCE/DIMMER
This control is used for adjusting the level of the
low frequency sound range.
1
Press the TONE/BAL button.
Each time the TONE/BAL button is pressed, the
mode is changed as follows:
Treble control
This control is used for adjusting the level of the
high frequency sound range.
BASS
TREBLE
BALANCE
DIMMER
(normal display)
Balance control
This control is used for adjusting balance of the
volume level between the left and right channels.
2
Within 3 seconds, turn the VOLUME/SELECT
knob to change the setting.
Dimmer control
This control can be used to dim the display panel
or to return it to normal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to CDs
2
4
1
3
5
1
Press the CD/TAPE button to select ‘CD’.
4
Press the OPEN/CLOSE button (L) to close the
tray.
‘No Disc’ will be displayed if no disc is set.
The total number of the tracks and total play time
of the disc is displayed.
2
Press the OPEN/CLOSE button (L).
5
Press the G(PLAY) button.
Playback starts from the first track.
3
Place a disc on a tray with the printed surface
up.
< When a disc is set on the disc tray, pressing the
CD button will start playback.
< If the source is set to ‘CD’, the unit will
automatically start playback when you turn on
the unit next time.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
C
D
B A
A
D
Search for a part of a track
To stop playback
Press the H (STOP) button to stop playback.
During playback, hold down the . m or
,/ button and release it when the part you
want to listen to is found.
On the remote control use them or , button.
B
To suspend playback temporarily (pause
mode)
Press the J (PAUSE) button. Playback stops at the
current position.
E
Direct Playback
To resume playback, press the G(PLAY) button or
J (PAUSE) button.
While in stop or playback mode, you can use the
numeric buttons of the remote control unit to
select a track.
Press the numeric buttons to select a track.
Playback starts from the selected track.
C
To skip to the next or a previous track
Press the .mor,/ button several times
until the desired track is found. The selected track
will be played from the beginning.
On the remote control press the .or/ (SKIP)
button.
< When the .m button is pressed once during
playback, the track being played will be played
from the beginning.
To return to the beginning of the previous track,
press the .m button twice.
For instance, to select track number 35, press ‘3’
and ‘5’.
To select numbers less than 10, press ‘0’ and then
the number. As an example, to select number 5,
press ‘0’ and ‘5’. (Optionally, you may press just the
number ‘5’ and then wait a few seconds.)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmed Playback
.m/,/
PROGRAM/
MEMORY
CLEAR
3
< This function allows you to program up to 32 tracks
Press the
y
(PLAY) button to start
for playback in any desired order.
programmed playback.
1
Press the PROGRAM/MEMORY button in the
stop mode.
< The programmed contents are not lost even if the
unit is turned off, but they are lost when the disc
tray is opened.
< The unit will stop automatically when the playback
of all the programmed tracks is finished, and the
program contents disappears from the display, but
they are not lost.
< To start program playback again, press the
PROGRAM/MEMORY button and the PLAY button.
2
Select the desired track by pressing the .
or/ (SKIP) button and press the PROGRAM/
MEMORY button to enter.
To check the programmed order
Press the PROGRAM/MEMORY button repeatedly in
the stop mode. The track number and program
number will be shown on the display.
Repeat this step to store other tracks.
< If you attempt to program more than 32 tracks,
‘FULL’ is displayed and no more can be
programmed.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Shuffle Playback
To delete a track from the program
In the stop mode, press the PROGRAM button
repeatedly until the program number to be deleted
appears on the display, then press the CLEAR
button. The selected track is deleted from the
program.
Press the SHUFFLE button in the stop or play
mode.
The tracks will be played randomly.
To clear the program
1. In the stop mode, press the PROGRAM/MEMORY
< If you press the SKIP button (/) during shuffle
playback, next track will be randomly selected and
played. If you press the SKIP button (.), the
currently played track will be played from the
beginning. A track cannot be replayed during
shuffle playback.
button.
2. Hold down the CLEAR button for more than 2
seconds.
< To stop shuffle playback, press the SHUFFLE or STOP
(H) button.
< If the OPEN/CLOSE button is pressed, the
programmed contents will also be cleared.
To add a track to the program
In the stop mode, press the PROGRAM/MEMORY
button repeatedly until the program number you
want to insert a track appears on the display. If you
want to add a track to the end of the program,
press the PROGRAM button repeatedly until ‘P-
END’ briefly appears on the display.
Then select a track number pressing the .
or/ (SKIP) buttonsand press the PROGRAM/
MEMORY button to enter. The track is added to
the program.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Playback
Every time the REPEAT 1/ALL button is pressed,
the mode is changed as follows:
Repeat A-B
This function allows repeat playback of any desired
portion of the disc.
Repeat one track
1. Designate the point at which repeat playback
should start by pressing the A-B button.
‘Rs’ blinks.
2. When the point at which repeat playback should
end is reached, press the A-B button again.
‘Rs’ lights up.
Repeat All
Repeat off
3. The designated point with A-B button will be
played back repeatedly.
< To return to normal play, press A-B button until ‘Rs’
disappears from the display.
Repeat one track [R1]
The track being played will be played repeatedly. If
you select another track in R1 mode, the track you
selected will be played repeatedly.
Repeat All [Ra]
All the tracks of the selected disc will be played
repeatedly.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Display
Listening to the External Sources
Each time the TIME button is pressed during
playback,the display changes as follows:.
You can connect external sources such as VCR deck or
TV to the AUX input jacks.
elapsed time of the current track
Press the TUNER/AUX 1/2 button to select ‘AUX
1’ or ‘AUX 2’.
remaining time of the current track
remaining time of the disc
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your DAB Tuner
Auto Tuning
The first time you listen to the DAB radio, it will scan
for DAB channels and build a channel list.
If you move the unit to a new area or you want to
check to see if there are new channels available in
your area, you can scan to find new channels
automatically.
To enter the DAB mode, turn the unit on, and
select DAB by pressing theTUNER/AUX 1/2
button and the BAND button.
Press the AUTO TUNING button.
The following screen will display for 2 seconds.
The unit will scan for any new channels and add the
channels found to the channel list.
< Press and hold the AUTO TUNING button for longer
than 2 seconds to activate international search.
The unit will scan for broadcast services in the local
area and add them to the channel list as they are
found. The scan should take about 10 seconds.
As channels are added to the channel list the number
of channels found is displayed.
After broadcast services have been found the channels
are listed in alphanumeric order.
< If no broadcast services are found, please check
that the antenna is correctly connected to the unit.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Channel List
3 1
2
Follow the steps below to tune in and listen to the
channels found by the unit.
1
Select DAB by pressing the BAND button.
v
< To display the signal strength of a channel, press
the ENTER button again. The signal strength is
displayed. Press the ENTER button once again to
cancel the signal strength display.
2
Press the TUNING/PRESET/TIME button to find
the channel in the channel list.
< Channels are displayed in alphanumeric order in
the channel list, with numbers coming first. So,
stations such as 6 Music from the BBC will be listed
early in the list.
The current channel is displayed on the first line
and the changing list is displayed on the second
line.
< If a channel is no longer broadcasting or the unit is
moved out of the area of a broadcast channel, the
unit will no longer be able to tune in the channel. If
the channel cannot be tuned in a question mark (?)
is displayed in front of the channel name. If you
select this channel to tune in by pressing the ENTER
button, ‘No stations Available’ is displayed.
3
When you have found a channel that you
want to listen to, press the ENTER button
once.
< You can remove a channel that is no longer
available from the channel list. See Tidy station,
page 23.
The channel is tuned in and channel information is
displayed.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Function Control 1
VOLUME/SELECT
Station order
Use station order to set the order in which stations are
listed. There are four orders: Favourite, Alphanumeric,
Active and Tidy.
1
While listening to a DAB broadcast press the
FUNCTION/FM MODE button.
ENTER
FUNCTION/
FM MODE
In DAB mode, use Function Control to set system
options. There are 6 options in the function control.
2
Press the TUNING/PRESET/TIME button until
‘Station order’ is displayed in the second line
of the display.
Station order
Signal error rate
Preset tune
Software version
DRC value
Manual tune
3
Press the ENTER button.
The current option is displayed in the first line of
the display.
4
Press the TUNING/PRESET/TIME button until
the desired option is displayed in the second
line of the display.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press the ENTER button.
Sig error rate (Signal error rate)
This option shows the digital bit error rate (0-99) of
the currently tuned channel. This is for information
only and no adjustment is available. The lower the
figure the better the quality of the received broadcast.
1
While listening to a DAB broadcast press the
FUNCTION/FM MODE button.
Fav Station (Favourite station)
As you tune in stations and listen to them the unit
will memorize the top ten stations you listen to and
list them at the top of the channel list. A Favourite
station in the channel list has ‘ ’ displayed after
the station name on the first line of the display.
Alphanumeric
2
Press the TUNING/PRESET/TIME button until
‘Sig error rate’ is displayed in the second line
of the display.
This is the default order. Channels are listed by
name with numbers first and then alphabetically by
letters in the channel name.
Active station
This option will list active stations at the top of the
channel list and channels that are in the list but
have no service in your area to be listed last in the
channel list.
Tidy station
This option will list active stations and remove any
channels that are in the list but have no service in
your area from the channel list.
3
Press the ENTER button.
q preset
The digital bit error rate of the current tuned
channel is displayed.
This option takes your top ten Favourite channels
and assigns them to preset numbers 1 - 10.
This option is only available after ‘Fav Station’
option has been turned on. See above.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Function Control 2
5
Preset tune
Use this option to select the DAB preset station.
Press the ENTER button to select the preset
station.
1
While listening to a DAB broadcast press the
FUNCTION/FM MODE button.
2
Press the TUNING/PRESET/TIME button until
‘Preset tune’ is displayed in the second line of
the display.
Sw version (Software version)
This option shows the version number of the installed
software. This is for information only and no
adjustment is available.
3
Press the ENTER button.
1
While listening to a DAB broadcast press the
FUNCTION/FM MODE button.
The currently tuned station is displayed.
2
Press the TUNING/PRESET/TIME button until
‘Sw version’ is displayed in the second line of
the display.
4
Press the TUNING/PRESET/TIME button until
the desired preset station is displayed.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press the TUNING/PRESET/TIME button until
the desired level of DRC is displayed in the
second line of the display.
DRC value
This option sets the Dynamic Range Control (DRC)
value to be applied to received broadcasts. DRC is
used to reduce the range between high and low
volumes of audio and is sometimes applied at the
broadcast source. Pop music may have a high value of
DRC applied, appropriate for constantly high listening
levels, while classical music broadcasts may have no
DRC applied to allow the listener to hear the full
dynamic range of the source volume.
There are three values of DRC you can apply.
0
: None
1/2 : Medium
: Maximum
1
5
Press the ENTER button.
1
While listening to a DAB broadcast press the
FUNCTION/FM MODE button.
2
Press the TUNING/PRESET/TIME button until
‘DRC value’ is displayed in the second line of
the display
3
Press the ENTER button.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Function Control 3
5
Press the ENTER button when the channel you
wish to tune in is displayed in the second line
of the display.
Manual tune
This option allows you to manually tune in a channel
and view a continuously updated display of the
strength of the signal. This may be useful when
adjusting or positioning an antenna for better
reception.
The signal strength indicator is displayed.
1
While listening to a DAB broadcast press the
FUNCTION/FM MODE button.
2
6
7
Press the TUNING/PRESET/TIME button until
‘Manual tune’ is displayed in the second line
of the display.
While viewing the indicator, adjust or
reposition the antenna until the best reception
is indicated.
Press the ENTER button to cancel Manual tune
and resume normal reception.
3
Press the ENTER button.
‘Manual tune’ is displayed on the first line of the
display.
4
Press the TUNING/PRESET/TIME button to find
the channel.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Display Settings
You can choose the type of information displayed in
Multiplex name
the second line of the display while listening to a DAB
channel.
This displays the name of the Mulitplex that is
broadcasting the programme.
Each time the INFO/RDS MODE button is pressed,
the information is displayed as follows.
Date and time
This displays the current date and time, which is
supplied by the radio station and should always be
accurate.
< The clock setting will be automatically adjusted
according to the clock time data.
DLS
If you tune in a DAB station broadcasting incorrect
clock time data, the clock might be wrongly
adjusted, and that may eventually affect the timer
operation.
Programme type
Multiplex name
Date and time
Bitrate mode
No matter which DAB mode is selected, the
unit receives clock time data and adjusts the
clock.
Channel and frequency
Bitrate mode
DLS
This displays the bitrate of the current playing
broadcast.
The Dynamic Label Segment (DLS) is the scrolling text
label supplied by the radio station. It may be
information on music titles or details regarding the
programme or station.
Channel and frequency
This displays the channel and frequency of the current
playing broadcast.
Programme type
This is a description of the type of broadcast supplied
by the radio station such as Pop, Rock or Classical
music.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to FM/AM
Selecting stations which cannot be tuned
automatically (Manual tune)
3
Select ‘Manual tune’ in step
.
Repeatedly press the TUNING/PRESET/TIME button
until the station you want to listen to is found. Or
hold down the TUNING/PRESET/TIME button until
the station you want to listen to is found and
release the button.
1
3 2
4
FM: 50 kHz steps, AM: 9 kHz steps
1
2
3
Press the TUNER/AUX 1/2 button to select
‘TUNER’.
< ‘STEREO’ is displayed when a stereo broadcast is
tuned in.
< ‘TUNED’ is displayed when a broadcast is correctly
tuned in.
Press the BAND button to select FM or AM.
Press the TUNING MODE button to select the
‘Auto tune’ mode.
FM MODE Button
Pressing this button alternates between Stereo
mode and Mono mode.
Stereo
Each time the TUNING MODE button is pressed, the
mode is changed as follows.
FM stereo broadcasts are received in stereo and the
STEREO indicator lights in the display.
Manual tune
Auto tune
Mono
To compensate for weak FM stereo reception,
select this mode. Reception will now be forced
monaural, reducing unwanted noise.
Preset tune
4
Select the station you want to listen to (auto
selection).
When a station is tuned in, the tuning process will
stop automatically.
If you want to stop the tuning process, press the
TUNING/PRESET/TIME button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Tuning 1
You can also use the numeric buttons of the
TUNING/PRESET/TIME
remote control unit.
MEMORY
BAND
For instance, to select preset number 25, first press
the TUNER button, and then press ‘2’ and ‘5’.
You can store up to 30 FM, 30 AM and 10 DAB
stations.
To select numbers less than 10, press ‘0’ and then
the number. As an example, to select number 5,
press ‘0’ and ‘5’. (Optionally, you may press just
the number ‘5’ and then wait a few seconds.)
Preset Manually (FM/AM/DAB)
1
Select DAB, AM or FM by pressing the BAND
button.
5
Within 4 seconds, press the PROGRAM/
MEMORY button.
2
3
Tune the station you would like to store.
< If you don’t press the PROGRAM/MEMORY button
within 4 seconds after selecting the channel, the
selection will be canceled.
Press the PROGRAM/MEMORY button briefly.
1
5
To store more stations, repeat steps to
.
FM or AM
DAB
Preset Automatically (FM/AM only)
1
Select AM or FM by pressing the BAND button.
‘CH01’ or ‘01’ blinks on the display.
2
Press the MEMORY button for more than 3
seconds.
4
Within 4 seconds, select the preset you would
like to use for this station using the
TUNING/PRESET/TIME buttons.
Up to 30 of the best received stations in your area
will be stored automatically.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Tuning 2
2 1
3
< Preset channels can also be selected by the PRESET
CALL buttons or the numeric buttons of the remote
control unit.
How to select DAB preset stations
See ‘Preset tune’ of page 24.
< When using the remote control unit, you can skip
2
step
.
How to select FM/AM preset stations
1
2
3
Select AM or FM by pressing the BAND button.
Select ‘Preset tune’ by pressing the TUNING
MODE button.
Select a preset channel.
Press the TUNING/PRESET/TIME button repeatedly
until the desired preset station is found.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
RDS
The Radio Data System(RDS) is a broadcasting service
RDS RADIO TEXT
which allows stations to send additional information
along with the regular radio programme signal.
When you select RDS RADIO TEXT, ‘RDS RADIO
TEXT’ will blink for about 3 seconds and then the
news of stations composed of up to 64 symbols
will be displayed.
RDS works on the FM waveband in Europe only.
If there is no radio text data, RDS mode will be
automatically switched to PROGRAM SERVICE
mode.
1
2
1
3
Tune in an FM station (see steps
page 28).
to
of
TRAFFIC ANNOUNCE
Press the RDS MODE button.
When you select TRAFFIC ANNOUNCE, ‘TRAFFIC
ANNOUNCE’ will blink for 3 seconds and then the
unit searches for a traffic announcement.
< When a traffic programme is found, the TRAFFIC
ANNOUNCE mode is switched to PROGRAM
SERVICE mode.
If the station currently selected is transmitting a
traffic program signal, the RDS mode will be
switched to PROGRAM SERVICE mode without
searching for a traffic program.
Each time the RDS MODE button is pressed briefly,
the RDS mode is changed as follows:
PROGRAM SERVICE
When you select PROGRAM SERVICE, ‘PROGRAM
SERVICE’ will blink for about 3 seconds and then
the programme service name or a station’s name
will be displayed. If there is no programme service
data, the frequency will be displayed.
RDS CLOCK TIME
displays the information about times provided
from the station.
When you select RDS CLOCK TIME, ‘RDS CLOCK
TIME’ will blink for about 3 seconds and then the
clock time will be displayed.
If there is no time data, ‘NO CT’ will be displayed.
RDS PROGRAM TYPE
When you select RDS PROGRAM TYPE, ‘RDS
PROGRAM TYPE’ will blink for about 3 seconds
and then the programme type will be displayed.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
PTY Search
2
4 1
3
5
5
You can search for stations by programme type.
Press the TUNING/PRESET/TIME button.
1
Select FM by pressing the BAND button.
Search starts.
< When the programme that you have selected is
found, searching stops and the programme type
will be displayed.
2
Press the INFO/RDS MODEbutton for more
than 3 second.
< If the same programme type is not found during
PTY Search, it will stop at the beginning frequency.
< If you want to stop searching, press the INFO/RDS
MODE button.
3
Select the desired PTY programme using the
TUNING/PRESET/TIME buttons.
Select your desired one from among 31 kinds of
PTY programmes. The programme type will blink.
4
Press the ENTER/SET button.
The programme type stops blinking.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
About DAB
NEWS
: brief announcements, events, public
opinion, reports, actual situations.
With this unit you can receive and listen to Digital
Audio Broadcast (DAB) programmes. DAB uses digital,
not analogue signals, resulting in near CD-quality
audio with virtually interference-free reception. Along
with superior quality audio, DAB can also deliver
additional audio channels and text. In the future,
computer data and images are also possible.
AFFAIRS
: a kind of suggestion including practical
announcements other than news,
documents, discussion, analysis and so on.
: daily information or reference such as
weather forecast, consumer guide, medical
assistance and so on.
INFO
SPORT
: sports related programs.
Digital radio is broadcast as groups of data called
ensembles or multiplexes. Each multiplex can contain a
number of stations (services) and each station contains
a primary service and can contain secondary services
as illustrated in the following diagram.
EDUCATE : educational and cultural information.
DRAMA : all kinds of radio concert and serial drama.
CULTURE : all aspects of national or local culture
including religious events, philosophy, social
science, language, theatre, and so on.
SCIENCE
: programs on natural science and
technology
DAB SIGNAL
VARIED
: popular programs such as quiz,
entertainment, private interview, comedy,
satire and so on.
POP M
: program on commercial, practical and
popular songs, and sale volume of discs,
etc.
BBC
National
DAB
MULTIPLEX
1
2
ROCK M
EASY M
LIGHT M
: practical modern music generally composed
and played by young musicians.
: popular music usually lasting for less than 5
minutes.
PRIMARY
SERVICES
BBC Radio 4
Parliament
1
3+
: classical music, instrumental music, chorus,
and light music favored by non-
professionals.
SECONDARY
SERVICES
1
4+
2
3
CLASSICS : orchestra including great operas,
symphony, chamber music and so on.
OTHER M : other music styles(Rhythm & Blues, Reggae,
etc.)
Each multiplex is transmitted in a set frequency range
and received by this unit for decoding. You can receive
multiplexes broadcast in the 174-240 MHz frequency
band and store the services in each multiplex for you
to access. The number of multiplexes you receive
depend on your location. Channels used in the UK are
in the range 10A to 12D.
WEATHER : weather reports, forecast
FINANCE : financial reports, commerce, trading
CHILDREN : children’s programs
SOCIAL
: social affairs
RELIGION : religious programs
PHONE IN : program in which the public expresses its
view by phone.
Multiplexes and stations have labels (names) that are
used to identify them. Instead of needing to know the
particular frequency of your favourite broadcast, you
can simply select the station name. Secondary services
and additional data such as text or multiplex info are
also available.
TRAVEL
LEISURE
JAZZ
: travel reports
: programs concerning recreational activities
: jazz music
COUNTRY : country music
NATION M: national music
OLDIES
: music from the so-called golden of popular
music
FOLK M
: folk music
DOCUMENT: documentaries
TEST
ALARM
: a program notifying an emergency or a
natural disaster.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock
TUNING/PRESET/TIME
ENTER/SET
TIME
MODE
1
3
Press the TIME MODE button.
Press the ENTER/SET button.
Every time the TIME MODE button is pressed, the
mode is changed as follows.
The ‘minute’ value blinks.
Current time
On time
4
Press the TUNING/PRESET/TIME buttons to set
the current minute.
Off time
Source select
< The unit uses the 24 hour ‘military’ clock.
< When no action is taken for 1 minute, the time
adjust mode will be cancelled.
5
Press the ENTER/SET button.
2
Press the TUNING/PRESET/TIME buttons to set
the current hour.
The clock starts from 00 second.
< Press the STOP button to cancel the time setting.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Timer
4
2
3
Repeat step and to set the Off time.
TUNING/PRESET/TIME
‘Source select’ appears on the display.
5
Press the TUNING/PRESET/TIME buttons to
select the source, and press the ENTER/SET
button.
ENTER/SET
TIME
MODE
< Adjust the clock before setting the timer.
< When no action is taken for 1 minute, the timer
setting mode will be cancelled.
Now the timer setting is stored in memory.
1
2
3
Press the TIME MODE button repeatedly until
‘On time’ is displayed.
6
Press the TIMER button.
‘On time’ appears on the display, and the ‘hour’
value blinks.
The timer indicator ‘ ’ lights on the display.
7
Prepare for timer operation.
Press the TUNING/PRESET/TIME buttons to set
the hour value, and press the ENTER/SET
button.
Adjust the volume, tune in a station, set CD, etc.
All the units connected by remote control cords will
turn on and off at the specified time every day.
When you don’t use timer, press the TIMER button
to turn it off. (The timer indicator ‘ ’ disappears
from the display.)
Press the TIMER button again to turn it on.
The ‘minute’ value blinks.
Press the TUNING/PRESET/TIME buttons to set
the minute value, and press the ENTER/SET
button.
8
Press the STANDBY/ON button to turn the unit
standby.
‘Off time’ appears on the display, and the ‘hour’
value blinks.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Reset the Settings
to the Factory Defaults
Sleep Timer
If the power supply is interrupted for 14 days or
longer, all the settings kept in memory (such as preset
stations and timer settings) will be erased.
It will take more than 3 days after plugging the power
cord into the outlet to charge enough electricity for
the memory backup function.
If you want to manually initialize the settings,
hold down the FUNCTION/FM MODE button for
more than 4 seconds in stanby mode.
The power can be switched off after a specified
amount of time.
Press the SLEEP button repeatedly until desired time
appears on the display.
SLEEP-90 (80, 70 ... 10)
The power will be switched off 90 (80, 70 ... 10)
minutes later.
(normal display)
The sleep timer is off.
< The display is dimmed when you set the sleep
timer.
< If you want to check the remaining time, press the
SLEEP button once. The remaining time will be
displayed for 3 seconds, and return to the normal
display.
The unit will be turned on, and all the settings are
reset to the default settings.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
AMPLIFIER Section
GENERAL
Output Power . . . . .25 W/ch (6 ohms, 0.5 %,1 kHz)
Input Sensitivity . . . . . . . . . . . . . 300 mV/47k ohms
Frequency Response . 20 Hz to 60,000 Hz (+1/-3dB)
Power Requirements . . . . . . . . . . 230 V AC, 50 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . 75 W
(standby) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 W
Dimension (W x H x D) . . . . . .215 x 110 x 359 mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.4 kg
TUNER Section
FM Section
Tuning Range . . . . . . . . 87.50 MHz to 108.00 MHz
(50 kHz steps)
Signal-to-Noise Ratio . . . . . . . . . . . . . 65dB (Mono)
60dB (Stereo)
Standard Accessories
Remote Control Unit (RC-956) x 1
Batteries (AAA) x 2
AM Loop Antenna x 1
FM Lead-type Antenna x 1
DAB Antenna x 1
Owner’s Manual x 1
Warranty Card x 1
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
AM Section
Tuning Range . . . . . . . . . . . . 522 kHz to 1629 kHz
(9kHz steps)
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . 35 dB
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
• Design and specifications are subject to change
without notice.
• Weight and dimensions are approximate.
• Illustrations may differ slightly from production
models.
DAB Section
Tuning range . . . . . . . . . Band 3, 174MHz-240MHz
Input . . . . . . . . . . . . . . . . . . . . . 50 ohms, nominal
Max signal . . . . . . . . . . . . . . . . . . . . . . . –3dBm typ
Sensitivity . . . . . . . . . . . . . . . . . . . . . . –96dBm typ
Adjacent Channel Rejection . . . . . . . . . . . 35dB typ
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Audio output . . . . . . . . . . . . . . . . .Stereo, 2.5V P-P
Digital output . . . . . . . . . . 24 bit/48 kHz resolution
CD PLAYER Section
Frequency Response . . . 20 Hz to 20,000 Hz ( 2dB)
Signal-to-Noise Ratio . . . . . . . . . . . more than 85dB
Wow and Flutter . . . . . . . . . . . . . . . Unmeasurable
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
In case of trouble with the unit, please take the time to look through this chart and see if you can solve the
problem yourself before you call your dealer or TEAC service center.
Amplifier
DAB tuner
No power
No sound.
e Check the connection to the AC power supply.
e Ensure that the CR-H250 has been able to locate
DAB stations.
No sound from speakers.
e Check the connection to the speakers.
e Adjust the volume.
e Select proper source.
‘NO stations Available’ appears on the display.
e Check that antenna is connected (see page 7).
e Ensure that DAB coverage exists in your area.
e Pull out the headphone plug from PHONES jack.
e If muting is on, press the MUTING button.
Cannot access secondary services.
e At the time of publishing not many secondary
services are available, this will increase as more
DAB stations start broadcasting. If a secondary
service station is available, the secondary indicator
>> will be displayed next to the station name.
The sound is noisy.
e The unit is too close to a TV set or similar
appliances. Install the unit apart from them, or
turn them off.
Display goes out or displayed ‘service off air’.
e This may occur if a broadcaster changes the label
of a service or removes a label whilst you are
listening to it. The CR-H250 will try to retune to
this station, or alternatively follow the procedure
for auto tune on page 26.
Remote Control Unit
Remote control doesn’t work.
e If the batteries are exhausted, change the
batteries.
e Use remote control unit within the range (5m)
and point at the front panel.
e Clear obstacles between the remote control unit
and the main unit.
e If a fluorescent light is near the unit, turn it off.
Cannot listen to the selected station.
e Ensure you have pressed the ENTER button when
you want to listen to your selection. The station
you are currently listening to will be displayed on
the first line of the display, as you scroll through
the station order list the second line will show
other station options. Press the ENTER button to
activate your selection.
Tuner (FM/AM)
Cannot listen to any station, or signal is too
weak.
A burbling sound is heard on some stations.
e DAB like other digital media is good at producing
quality audio from a low level signal, however if
this signal level is too low a ‘burbling’ sound can
sometimes be heard. To reduce this, try
repositioning your antenna to gain maximum
signal strength.
e Tune in the station properly.
e If a TV is near the unit, turn it off.
e Install the antenna again after locating the best
reception position.
e An external antenna is recommended.
Though the broadcast is stereo, it sounds
monaural.
e Press the FM MODE button.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CD Player
Maintenance
Cannot play.
If the surface of the unit gets dirty, wipe with a soft
cloth or use diluted neutral cleaning liquid. Be sure to
remove any fluid completely. Do not use thinner,
benzine or alcohol as they may damage the surface of
the unit.
e Load a disc with label side up.
e If the disc is dirty, clean the surface of the disc.
e A blank disc has been loaded. Load a prerecorded
disc.
e Unfinalized CD-R/CD-RW disc is not playable.
Finalize the disc properly.
Beware of condensation
Sound skips.
When the unit (or a disc) is moved from a cold to a
warm place, or used after a sudden temperature
change, there is a danger of condensation; vapor in
the air could condense on the internal mechanism,
making correct operation impossible. To prevent this,
or if this occurs, leave the unit for one or two hours
with the power turned on. The unit will stabilize at the
temperature of its surroundings.
e Place the unit on a stable place to avoid vibration
and shock.
e If the disc is dirty, clean the surface of the disc.
e Don’t use scratched, damaged or warped discs.
No program playback.
e In the stop mode press PROGRAM button to
enter the program mode, and press play button
to start playing.
If normal operation cannot be recovered, unplug
the power cord from the outlet and plug it again.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Z
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan Phone: (0422) 52-5081
TEAC CORPORATION
TEAC AMERICA, INC.
TEAC CANADA LTD.
7733 Telegraph Road, Montebello, California 90640 Phone: (323) 726-0303
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Phone: (905) 890-8008
TEAC MEXICO, S.A. De C.V Campesinos N°184, Colonia Granjas Esmeralda, Delegacion Iztapalapa, CP 09810, México DF Phone: (525) 581-5500
TEAC UK LIMITED
5 Marlin House, Croxley Business Park, Watford, Hertfordshire, WD18 8TE, U.K. Phone: 01923-819699
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany Phone: 0611-71580
TEAC EUROPE GmbH
TEAC FRANCE S.A.
TEAC ITALIANA S.p.A.
17, Rue Alexis-de-Tocqueville, CE 005 92182 Antony Cedex, France Phone: (1) 42.37.01.02
Via C. Cantù 11, 20092 Cinisello Balsamo, Milano, Italy Phone: 02-66010500
TEAC AUSTRALIA PTY., LTD. 280 William Street, Melbourne VIC 3000, Australia Phone: (03) 9672-2400
A.B.N. 80 005 408 462
This appliance has a serial number located on the rear panel. Please record
the model number and serial number and retain them for your records.
.
Model number
Serial number
0704 MA-0906A
Download from Www.Somanuals.com. All Manuals Search And Download.
|