Taylor Refrigerator taylor User Manual
OPERATOR’S  
MANUAL  
Model 150, 152, 162, & 168  
Soft Serve Freezers  
Original Operating Instructions  
028749- M  
8/13/08 (Original Publication)  
Updated 8/6/14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Section 1  
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
1
1
1
2
Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Electrical Hook- Up Installation For  
60 Cycle, 1 Phase, Supplied With Cord and Plug . . . . . . . . . . . . . . . . . . . . . . . . . .  
2
Electrical Connections For  
Models Without Cord and Plug Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
2
3
3
Beater Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Section 2  
To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
4
5
7
Section 3  
Section 4  
Model 150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Model 152 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Model 162 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
7
8
9
Model 168 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Models 150 & 152 Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Models 162 & 168 Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Models 150 and 152 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Models 162 and 168 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Section 5  
Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Feed Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Taylor Quality Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Indicator Light - “Mix Low” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Mix Refrigeration Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Separate Hopper Refrigeration (SHR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Cylinder Temperature Retention (CTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Section 6  
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Models 150, 152, 162, 168  
Table of Contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents - Page 2  
Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Draining Product From the Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Section 7  
Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Section 8  
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Section 9  
Section 10  
Section 11  
Section 12  
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Note: Continuing research results in steady improvements; therefore, information  
in this manual is subject to change without notice.  
Note: Only instructions originating from the factory or its authorized translation  
representative(s) are considered to be the original set of instructions.  
E 2008 Carrier Commercial Refrigeration, Inc. (Original Publication)  
Updated August, 2014  
028749- M  
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work  
may be a violation of Copyright Law of the United States of America and other countries, could result in the  
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further  
civil and criminal penalties.  
All rights reserved.  
Taylor Company  
a division of Carrier Commercial Refrigeration, Inc.  
750 N. Blackhawk Blvd.  
Rockton, IL 61072  
Table of Contents  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 1  
To the Installer  
The following information has been included in the  
manual as safety and regulatory guidelines. For  
complete installation instructions, please see the  
Installation Checklist.  
This unit has many sharp edges that can  
cause severe injuries.  
Installer Safety  
Site Preparation  
In all areas of the world, equipment should be  
installed in accordance with existing local codes.  
Please contact your local authorities if you have any  
questions.  
Review the area the unit is to be installed in before  
uncrating the unit, making sure that all possible  
hazards the user or equipment may come into have  
been addressed.  
Care should be taken to ensure that all basic safety  
practices are followed during the installation and  
servicing activities related to the installation and  
service of Taylor equipment.  
For Indoor Use Only: This unit is designed to operate  
indoors, under normal ambient temperatures of  
70_-75_F (21_-24_C). The unit has successfully  
performed in high ambient temperatures of  
104_(40_C) at reduced capacities.  
S
Only authorized Taylor service personnel  
should perform installation and repairs on the  
equipment.  
S
Authorized service personnel should consult  
OSHA Standard 29CFRI910.147 or the  
applicable code of the local area for the  
This unit must NOT be installed in an area  
where a water jet or hose can be used. NEVER use a  
water jet or hose to rinse or clean the unit. Failure to  
follow this instruction may result in electrocution.  
industry  
standards  
on lockout/tagout  
procedures before beginning any installation  
or repairs.  
Authorized service personnel must ensure  
that the proper PPE is available and worn  
when required during installation and service.  
Authorized service personnel must remove all  
metal jewelry, rings, and watches before  
working on electrical equipment.  
S
S
This unit must be installed on a level surface  
to avoid the hazard of tipping. Extreme care should be  
taken in moving this equipment for any reason. Two or  
more persons are required to safely move this unit.  
Failure to comply may result in personal injury or  
equipment damage.  
The main power supply(s) to the freezer must  
be disconnected prior to performing any repairs.  
Failure to follow this instruction may result in personal  
injury or death from electrical shock or hazardous  
moving parts as well as poor performance or damage  
to the equipment.  
Uncrate the unit and inspect it for damage. Report any  
damage to your Taylor Distributor.  
This piece of equipment is made in the USA and has  
USA sizes of hardware. All metric conversions are  
approximate and vary in size.  
Note: All repairs must be performed by an  
authorized Taylor Service Technician.  
131122  
1
Models 150, 152, 162, 168  
To the Installer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Route incoming permanent wiring through 7/8”  
(22 mm) hole in base pan.  
Air Cooled Units  
5. Connect two power supply leads. Attach ground  
(earth) wire to the grounding lug inside the  
electrical box.  
The models 150 and 152 require a minimum of 6” (152  
mm) of clearance around both sides. Install the skirt  
provided on the right side of the unit and place the back  
of the unit against a wall to prevent recirculation of  
warm air. The model 162 requires 6” (152 mm) on all  
sides and the skirt installed on the rear of the unit. The  
model 168 requires 3” (76 mm) on all sides and the  
skirt installed on the rear of the unit. Minimum air  
clearances must be met to assure adequate air flow for  
optimum performance.  
6. Be sure the unit is properly grounded before  
applying power.  
FOLLOW YOUR LOCAL ELECTRICAL CODES!  
These units are designed for indoor use only.  
Electrical Connections For  
Models Without Cord and Plug Supplied  
DO NOT install the units in an area where a  
water jet could be used. Failure to follow this  
instruction may result in serious electrical shock.  
Each freezer requires one power supply for each data  
label. Check the data label(s) on the freezer for branch  
circuit overcurrent protection or fuse, circuit ampacity,  
and electrical specifications. Refer to the wiring  
diagram provided inside of the control box, for proper  
power connections.  
In the United States, this equipment is intended to be  
installed in accordance with the National Electrical  
Code (NEC), ANSI/NFPA 70- 1987. The purpose of  
the NEC code is the practical safeguarding of persons  
and property from hazards arising from the use of  
electricity. This code contains provisions considered  
necessary for safety. Compliance therewith and  
proper maintenance will result in an installation  
essentially free from hazard! In all other areas of the  
world, equipment should be installed in accordance  
with the existing local codes. Please contact your local  
authorities.  
Electrical Hook- Up Installation For  
60 Cycle, 1 Phase, Supplied With Cord and Plug  
This equipment is supplied with a 3- wire cord and  
grounding type plug for connection to a single phase,  
60 cycle, branch circuit supply. This unit must be  
plugged into a properly grounded receptacle. The cord  
and plug provided for 115/60/1, is 20 amp; therefore  
the wall outlet must also be 20 amp. Check the data  
label, located on the side panel, for electrical  
specifications.  
CAUTION: THIS EQUIPMENT MUST BE  
PROPERLY GROUNDED! FAILURE TO DO SO  
CAN RESULT IN SEVERE PERSONAL INJURY  
FROM ELECTRICAL SHOCK!  
Permanent wiring may be employed if required by local  
codes. Instructions for conversion to permanent wiring  
are as follows:  
1. Be sure the freezer is electrically disconnected.  
This unit is provided with an equipotential  
grounding lug that is to be properly attached to the rear  
of the frame by the authorized installer. The installation  
location is marked by the equipotential bonding  
symbol (5021 of IEC 60417-1) on both the removable  
panel and the equipment’s frame.  
2. Remove the appropriate panel and locate the  
small electrical box at the base of the freezer.  
3. Remove the factory- installed cord and strain  
relief bushing.  
101122  
2
To the Installer  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical connections are made directly to the  
terminal block provided in the splice box, mounted on  
the base pan on each side of the model 168, and  
located in the splice boxes mounted mid- level on the  
frame channel on the sides of the model 162.  
S
S
Stationary appliances which are not equipped  
with a power cord and a plug or another device  
to disconnect the appliance from the power  
source must have an all-pole disconnecting  
device with a contact gap of at least 3 mm  
installed in the external installation.  
Refrigerant  
Appliances that are permanently connected to  
fixed wiring and for which leakage currents  
may exceed 10 mA, particularly when  
disconnected, not used for long periods, or  
during initial installation, shall have protective  
devices such as a GFI to protect against the  
leakage of current, installed by authorized  
personnel to the local codes.  
In consideration of our environment, Taylor  
uses only earth friendly HFC refrigerants. The HFC  
refrigerant used in this unit is R404A. This refrigerant  
is generally considered non-toxic and non-flammable,  
with an Ozone Depleting Potential (ODP) of zero (0).  
S
Supply cords used with this unit shall be  
oil-resistant, sheathed flexible cable, not  
lighter than ordinary polychloroprene or other  
equivalent synthetic elastomer-sheathed cord  
(Code designation 60245 IEC 57) installed  
with the proper cord anchorage to relieve  
conductors from strain, including twisting, at  
the terminals and protect the insulation of the  
conductors from abrasion.  
However, any gas under pressure is potentially  
hazardous and must be handled with caution.  
NEVER fill any refrigerant cylinder completely with  
liquid. Filling the cylinder to approximately 80% will  
allow for normal expansion.  
If the supply cord is damaged, it must be  
replaced by the manufacturer, its service  
agent, or similarly qualified person, in order to  
avoid a hazard.  
Use only R404A refrigerant that conforms to  
the AHRI standard 700 specification. The use of any  
other refrigerant may expose users and operators to  
unexpected safety hazards.  
Refrigerant liquid sprayed onto the skin may  
cause serious damage to tissue. Keep eyes and skin  
protected. If refrigerant burns should occur, flush  
immediately with cold water. If burns are severe, apply  
ice packs and contact a physician immediately.  
Beater Rotation  
Taylor reminds technicians to be cautious of  
government laws regarding refrigerant recovery,  
recycling, and reclaiming systems. If you have any  
questions regarding these laws, please contact the  
factory Service Department.  
Beater rotation must be clockwise as viewed  
looking into the freezing cylinder.  
Note: The following procedures should be  
performed by an authorized service technician.  
WARNING: R404A refrigerant used in  
conjunction with polyolester oils is extremely moisture  
absorbent. When opening a refrigeration system, the  
maximum time the system is open must not exceed 15  
minutes. Cap all open tubing to prevent humid air or  
water from being absorbed by the oil.  
To correct rotation on a three- phase unit, interchange  
any two incoming power supply lines at freezer main  
terminal block only. To correct rotation on a  
single- phase unit, change the leads inside the beater  
motor. (Follow diagram printed on motor.)  
130809  
3
Models 150, 152, 162, 168  
To the Installer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 2  
To the Operator  
The freezer you have purchased has been carefully  
engineered and manufactured to give you dependable  
operation. The Taylor Company models covered in this  
manual consist of the following: 150, 152, 162 and168.  
compliant with the EU Directive as well as other similar  
legislation in effect after August 13, 2005. Therefore,  
it must be collected separately after its use is  
completed, and cannot be disposed as unsorted  
municipal waste.  
These units, when properly operated and cared for, will  
The user is responsible for returning the product to the  
appropriate collection facility, as specified by your local  
code.  
produce  
a
consistent quality product. Like all  
mechanical products, they will require cleaning and  
maintenance. A minimum amount of care and  
attention is necessary if the operating procedures  
outlined in this manual are followed closely.  
For additional information regarding applicable local  
laws, please contact the municipal facility and/or local  
distributor.  
This Operator’s Manual should be read before  
operating or performing any maintenance on your  
equipment.  
Compressor Warranty Disclaimer  
The refrigeration compressor(s) on this unit are  
warranted for the term stated in the Limited Warranty  
section in this manual. However, due to the Montreal  
Protocol and the U.S. Clean Air Act Amendments of  
1990, many new refrigerants are being tested and  
developed, thus seeking their way into the service  
industry. Some of these new refrigerants are being  
advertised as drop- in replacements for numerous  
applications. It should be noted that in the event of  
ordinary service to this unit’s refrigeration system,  
only the refrigerant specified on the affixed data  
label should be used. The unauthorized use of  
alternate refrigerants will void your Taylor compressor  
warranty. It is the unit owner’s responsibility to make  
this fact known to any technician he employs.  
These units will NOT eventually compensate and  
correct for any errors during the set- up or filling  
operations. Thus, the initial assembly and priming  
procedures are of extreme importance. It is strongly  
recommended that personnel responsible for the  
equipment’s operation, both assembly and  
disassembly, go through these procedures together in  
order to be properly trained and to make sure that no  
misunderstandings exist.  
In the event you should require technical assistance,  
please contact your local authorized Taylor Distributor.  
Note: Your Taylor warranty is valid only if the parts are  
authorized Taylor parts, purchased from the local  
authorized Taylor Distributor, and only if all required  
service work is provided by an authorized Taylor  
service technician. Taylor reserves the right to deny  
warranty claims on units or parts if non- Taylor  
approved parts or incorrect refrigerant were installed  
in the unit, system modifications were performed  
beyond factory recommendations, or it is determined  
that the failure was caused by abuse, misuse, neglect,  
or failure to follow all operating instructions. For full  
details of your Taylor Warranty, please see the Limited  
Warranty section in this manual.  
It should also be noted that Taylor does not warrant the  
refrigerant used in its equipment. For example, if the  
refrigerant is lost during the course of ordinary service  
to this unit, Taylor has no obligation to either supply or  
provide its replacement either at billable or unbillable  
terms. Taylor does have the obligation to recommend  
a suitable replacement if the original refrigerant is  
banned, obsoleted, or no longer available during the  
five year warranty of the compressor.  
The Taylor Company will continue to monitor the  
industry and test new alternates as they are being  
developed. Should a new alternate prove, through our  
testing, that it would be accepted as a drop- in  
replacement, then the above disclaimer would  
become null and void. To find out the current status of  
an alternate refrigerant as it relates to your  
compressor warranty, call the local Taylor Distributor  
or the Taylor Factory. Be prepared to provide the  
Model/Serial Number of the unit in question.  
Note: Constant research results in steady  
improvements; therefore, information in this  
manual is subject to change without notice.  
If the crossed out wheeled bin symbol is  
affixed to this product, it signifies that this product is  
131122  
4
To the Operator  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 3  
Safety  
We, at Taylor Company, are concerned about the  
safety of the operator when he or she comes in contact  
with the freezer and its parts. Taylor has gone to  
extreme efforts to design and manufacture built- in  
safety features to protect both you and the service  
technician. As an example, warning labels have been  
attached to the freezer to further point out safety  
precautions to the operator.  
S
S
S
S
S
DO NOT operate the freezer unless it is  
properly grounded.  
DO NOT operate the freezer with larger fuses  
than specified on the freezer data label.  
All repairs must be performed by an  
authorized Taylor service technician.  
The main power supplies to the unit must be  
disconnected prior to performing any repairs.  
IMPORTANT - Failure to adhere to the  
following safety precautions may result in severe  
personal injury or death. Failure to comply with  
these warnings may damage the unit and its  
components. Component damage will result in  
part replacement expense and service repair  
expense.  
For Cord Connected Units: Only Taylor  
authorized service technicians or licensed  
electricians may install a plug or replacement  
cord on these units.  
S
S
Stationary appliances which are not equipped  
with a power cord and a plug or another device  
to disconnect the appliance from the power  
source must have an all-pole disconnecting  
device with a contact gap of at least 3 mm  
installed in the external installation.  
DO NOT operate the freezer without reading  
this Operator Manual. Failure to follow this instruction  
may result in equipment damage, poor freezer  
performance, health hazards, or personal injury.  
Appliances that are permanently connected to  
fixed wiring and for which leakage currents  
may exceed 10 mA, particularly when  
disconnected, not used for long periods, or  
during initial installation, shall have protective  
devices such as a GFI to protect against the  
leakage of current, installed by authorized  
personnel to the local codes.  
This appliance is to be used only by trained  
personnel. It is not intended for use by children or  
people with reduced physical, sensory, or mental  
capabilities, or lack of experience and knowledge,  
unless given supervision or instruction concerning the  
use of the appliance by a person responsible for their  
safety. Children should be supervised to ensure that  
they do not play with the appliance.  
S
Supply cords used with this unit shall be  
oil-resistant, sheathed flexible cable, not  
lighter than ordinary polychloroprene or other  
equivalent synthetic elastomer-sheathed cord  
(Code designation 60245 IEC 57) installed  
with the proper cord anchorage to relieve  
conductors from strain, including twisting, at  
the terminals and protect the insulation of the  
conductors from abrasion.  
This unit is provided with an equipotential  
grounding lug that is to be properly attached to the rear  
of the frame by the authorized installer. The installation  
location is marked by the equipotential bonding  
symbol (5021 of IEC 60417-1) on both the removable  
panel and the equipment’s frame.  
If the supply cord is damaged, it must be  
replaced by the manufacturer, its service  
agent, or similarly qualified person, in order to  
avoid a hazard.  
DO NOT use a water jet to clean or rinse the  
freezer. Failure to follow these instructions may result  
in serious electrical shock.  
Failure to follow these instructions may result in  
electrocution. Contact your local authorized Taylor  
Distributor for service.  
130304  
5
Models 150, 152, 162, 168  
Safety  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning and sanitizing schedules are  
governed by your state or local regulatory agencies  
and must be followed accordingly. Please refer to the  
cleaning section of this manual for the proper  
procedure to clean this unit.  
S
DO NOT allow untrained personnel to operate  
this unit.  
DO NOT put objects or fingers in door spout.  
DO NOT operate the freezer unless all service  
panels and access doors are restrained with  
screws.  
S
S
This unit is designed to maintain product  
temperature under 41_F (5_C). Any product being  
added to this unit must be below 41_F (5_C). Failure  
to follow this instruction may result in health hazards  
and poor freezer performance.  
S
DO NOT remove the freezer door or beater  
assembly unless the control switches are in  
the “OFF” position.  
Failure to follow these instructions may result in severe  
personal injury from hazardous moving parts.  
DO NOT obstruct air intake and discharge openings:  
S
150 and 152: Minimum of 6” (152 mm) of  
clearance around both sides. Install the skirt  
provided on the right side of the unit and place  
the back of the unit against a wall to prevent  
recirculation of warm air.  
162: Minimum of 6” (152 mm) on all sides.  
Install the skirt provided on the rear of the unit.  
This unit has many sharp edges that can  
cause severe injuries.  
S
DO NOT put objects or fingers in the door  
spout. This may contaminate the product and  
cause severe personal injury from blade  
contact.  
S
S
S
USE EXTREME CAUTION when removing  
the beater asssembly. The scraper blades are  
very sharp.  
168: Minimum of 3” (76 mm) on all sides.  
Install the skirt provided on the rear of the unit.  
For Indoor Use Only: This unit is designed to operate  
indoors, under normal ambient temperatures of  
70_-75_F (21_-24_C). The unit has successfully  
performed in high ambient temperatures of  
104_(40_C) at reduced capacities.  
This freezer must be placed on a level  
surface. Failure to comply may result in personal injury  
or equipment damage.  
DO NOT run the unit without product. Failure to follow  
this instruction can result in damage to the unit.  
Access to the service area of the unit is  
restricted to persons having knowledge and practical  
experience with the appliance, in particular as far as  
safety and hygiene are concerned.  
NOISE LEVEL: Airborne noise emission does not  
exceed 78 dB(A) when measured at a distance of 1.0  
meter from the surface of the unit and at a height of 1.6  
meters from the floor.  
130722  
6
Safety  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 4  
Operator Parts Identification  
Model 150  
Figure 1  
Item  
Description  
Part No.  
Item  
Description  
Part No.  
047667  
1
2
Cover A.- Hopper  
X48690  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
Decal- Decorative- Taylor  
Panel- Upper Side Right  
Light- Amber- Round Mix Low  
Caster- 3” Swivel  
Tube- Feed- .166 Hole  
Float A.- Mix Level  
Panel- Back Top  
035819  
030784- SS  
039707  
3
X39690  
4
050429  
012227  
5
Panel- Upper Side Left  
Pan- Drip 11- 5/8 Long  
Panel- Back Bottom  
Panel- Lower Side  
Panel- Insert  
030783- SS  
027503  
Panel A.- Front  
X25036  
025536  
6
Trim- Top Back Panel  
Trim- Middle Back Panel  
Trim- Side & Front  
7
050430  
025537  
8
030792- SS  
025533- SS  
X25518  
025528  
9
Plate- Decorative  
041034- SS  
035866  
10  
11  
12  
Panel A.- Lower Front  
Tray- Drip 10- 7/8 x 4- 7/16  
Holder- Drip Tray  
025062  
Caster- 3” Rigid  
012226  
Shield- Splash 11- 1/4 x 4- 13/16 025063  
7
Models 150, 152, 162, 168  
Operator Parts Identification  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 152  
Figure 2  
Item  
Description  
Part No.  
Item  
Description  
Part No.  
1
2
3
4
5
6
7
8
9
Cover A.- Hopper  
X48690  
035819  
X39690  
051556  
051557  
027503  
024755  
039707  
051558  
10  
11  
12  
13  
14  
15  
16  
17  
Shield- Splash 11- 1/4 x 4- 13/16 025063  
Tube- Feed- .166 Hole  
Float A.- Mix Level  
Panel- Rear  
Tray- Drip 10- 7/8 x 4- 7/16  
Decal- Decorative- Taylor  
Panel A.- Front  
025062  
047667  
X25036  
Panel- Side Left  
Trim- Front  
025862- SS  
025866  
Pan- Drip 11- 5/8 Long  
Leg- Plastic  
Trim- Top Back  
Plate- Decorative  
Holder- Drip Tray  
041034- SS  
035866  
Light- Amber- Round Mix Low  
Panel- Side Right  
8
Operator Parts Identification  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 162  
Figure 3  
Item  
Description  
Part No.  
Item  
Description  
Part No.  
030565  
1
2
Cover A.- Hopper  
X37963- SER  
030797  
11  
12  
13  
14  
15  
16  
17  
18  
19  
Tray- Drip- 16- 7/8 x 4- 3/8  
Panel- Front Right  
Trim- Front  
Tube- Feed- .166 Hole  
Float A.- Mix Level  
Panel- Rear  
035933- SS  
050212- SS  
035932- SS  
013458  
3
X39690  
4
047276- SS  
050213- SS  
035034  
Panel- Front Left  
5
Panel- Side- Left  
Leg- 4.250” (With O- Ring)  
Panel- Side Right  
Trim- Panel- Rear  
Plate- Decorative  
Holder- Drip Tray  
6
Pan- Drip 19- 1/2 Long  
Panel A.- Front  
050214- SS  
035923  
7
X30711  
8
Light- Amber- Round Mix Low  
Decal- Decorative- Taylor  
Shield- Splash  
039707  
039723- SS  
035866  
9
047666  
10  
030789  
9
Models 150, 152, 162, 168  
Operator Parts Identification  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model 168  
Figure 4  
Item  
Description  
Part No.  
Item  
Description  
Part No.  
1
2
Cover A.- Hopper  
X37963- SER  
030797  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
Panel- Upper Side Right  
Insert- Front Panel  
030784- SS  
030773- SS  
X30747  
Tube- Feed- .166 Hole SS  
Float A.- Mix Level  
3
X39690  
Panel A.- Lower Front  
Panel- Bottom Back  
4
Panel- Top Back  
030790- SS  
030783- SS  
027504  
055833  
5
Panel- Upper Side Left  
Pan- Drip 17- 1/4” Long  
Panel A.- Front  
Caster- 3” Rigid (Rear)  
Caster- 3” Swivel (Front)  
Panel- Lower Side- Right/Left  
Trim- Top Back Panel  
Trim- Middle Back Panel  
Plate- Decorative  
012226  
6
012227  
7
X30711  
030792- SS  
030775  
8
Light- Amber- Round Mix Low  
Decal- Decorative- Taylor  
Shield- Splash 17- 5/8 Long  
Tray- Drip 16- 7/8 Long  
039707  
9
047666  
030795  
10  
11  
030789  
039723- SS  
035866  
030565  
Holder- Drip Tray  
10  
Operator Parts Identification  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models 150 & 152 Door Assembly  
Figure 5  
Item  
Description  
Valve- Draw  
Part No.  
024763  
Item  
Description  
Door A.- 1 Spout  
Part No.  
1
2
3
4
5
6
7
8
9
X38959- SER  
014496  
O- Ring- 7/8 OD x .103 W  
O- Ring- 3/4 OD x .103 W  
Handle- Draw  
014402  
015835  
024762  
024761  
034829  
014218  
Bearing- Guide  
O- Ring- 2- 3/4 OD x .139 W  
Bearing- Front  
10  
11  
12  
13  
019998  
023262  
Arm- Valve Lifter  
Beater A.  
X24689  
Nut- Stud  
Seal- U- Cup  
080534  
Cap- Design 1.010” ID - 6 Point  
120501  
11  
Models 150, 152, 162, 168  
Operator Parts Identification  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models 162 & 168 Door Assembly  
Figure 6  
Item  
Description  
Valve- Draw  
Part No.  
024763  
Item  
Description  
Part No.  
014218  
1
2
3
4
8
9
Cap- Design 1.010” ID - 6 Point  
Pin A.- Pivot Long  
Valve- Draw- Center  
Bearing- Guide  
O- Ring- 7/8 OD x .103 W  
Seal- Draw Valve (H- Ring)  
Kit A.- Door 3 Spt 1.5 Qt. Valox  
014402  
X38538  
031164  
014496  
019998  
023262  
X24689  
080534  
030930  
10  
11  
12  
13  
14  
15  
X56906- SER  
056802  
4a Nut- Stud  
O- Ring- 2- 3/4 OD x .139 W  
Bearing- Front  
5
6
7
Pin A.- Pivot Short  
X38539  
016272  
O- Ring- 5/16 OD x .070 W  
Handle- Draw Valve  
Beater A.  
030564  
Seal- U- Cup  
120501  
12  
Operator Parts Identification  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models 150 and 152 Accessories  
Figure 7  
Item  
Description  
Kit A.- Tune Up  
Part No.  
Item  
Description  
Part No.  
1
2
3
4
X25802  
013071  
013072  
013073  
5
6
Brush- Mix Pump Body- 3 x 7 White 023316  
Brush- Rear Bearing 1” x 2”  
Brush- Double- Ended  
Pail- 6 Qt.  
023348  
See Note  
047518  
*7  
8
Sanitizer- Stera Sheen  
Lubricant- Taylor 4 Oz.  
Brush- Draw Valve 1 OD x 2 x 17  
*Note: A sample container of sanitizer is sent with the  
unit. For reorders, order Stera Sheen part no. 055492  
(100 2 oz. packs) or Kay-5 part no. 041082 (200 packs).  
140806  
13  
Models 150, 152, 162, 168  
Operator Parts Identification  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models 162 and 168 Accessories  
Figure 8  
Item  
Description  
Kit A.- Tune Up  
Part No.  
X31167  
Item  
Description  
Part No.  
023316  
1
2
3
4
5
6
Brush- Mix Pump Body- 3” x 7”  
Pail- 6 Qt.  
Brush- Rear Bearing 1” x 2”  
Brush- Double Ended  
013071  
013072  
013073  
023348  
See Note  
047518  
*7  
8
Sanitizer  
Brush- Draw Valve 1” x 2” x 17”  
Lubricant- Taylor 4 Oz.  
*Note: A sample container of sanitizer is sent with the  
unit. For reorders, order Stera Sheen part no. 055492  
(100 2 oz. packs) or Kay-5 part no. 041082 (200 packs).  
110804  
14  
Operator Parts Identification  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 5  
Important: To the Operator  
Figure 9  
The following chart identifies the symbol definitions  
used on the operator switches.  
Item  
Description  
1
2
3
4
5
Reset Button  
Power Switch  
Temperature Control  
Mix Refrigeration Switch  
Indicator Lights - “Mix Low”  
= ON/AUTO key  
= ON key  
= OFF key  
Symbol Definitions  
= WASH key  
To better communicate in the International arena, the  
words on many of our operator switches and buttons  
have symbols to indicate their functions. Your Taylor  
equipment is designed with these International  
symbols.  
= STANDBY key  
15  
Models 150, 152, 162, 168  
Important: To the Operator  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reset Button  
Taylor Quality Control  
If an overload condition occurs, the freezer will  
automatically stop operating. To properly reset the  
freezer, place the toggle switch in the “OFF” position.  
Wait two or three minutes; then press the reset button.  
Place the power switch in the “WASH” position and  
observe the freezer’s performance; place the power  
switch in the “AUTO” position.  
These units use a solid state control called the T.Q.C.  
The purpose of this solid state control is to sense the  
viscosity (thickness) of the product in the freezing  
cylinder. With the power switch in the “AUTO” position,  
the T.Q.C. will automatically keep the mix in the  
freezing cylinder at the proper viscosity and ready for  
serving.  
Note: If the freezer is unplugged from the wall  
receptacle, it will be necessary to press the reset  
button for the freezer to operate once power is  
re- established.  
Indicator Light - “Mix Low”  
A mix level indicating light is located at the front of the  
unit. When the light is on, it indicates that the mix  
hopper has a low supply of mix and should be refilled  
as soon as possible. Always maintain at least 2” (5.1  
cm) of mix in the hopper. If you neglect to add mix, a  
freeze- up may occur. This will cause eventual  
damage to the beater assembly and to the freezer  
door.  
Power Switch  
The center position is “OFF”. The left position is  
“WASH” which activates the beater motor only. The  
right position is “AUTO”, which activates the beater  
motor and the refrigeration system.  
Mix Refrigeration Switch  
Feed Tube  
The mix refrigeration switch is located under the  
control channel and is used for several purposes:  
The models 150, 152, 162 and 168 are called upon to  
handle a large variety of products (i.e., soft serve,  
yogurts, Italian ices, sherbets, etc.). Thus, the  
consistency of the mix you use will vary. The feed tube  
meters a combination of mix and air into the freezing  
cylinder. If not enough mix enters the freezing cylinder,  
a freeze- up may occur, which will cause eventual  
damage to the beater. Depending upon the product  
being run, you may wish to contact your local  
authorized Taylor Distributor to make a slight  
adjustment in the feed tube.  
1. For the unit to operate in the “AUTO” mode, the  
mix refrigeration switch must be “ON”.  
2. For the separate hopper refrigeration system to  
operate, the mix refrigeration switch must be in  
the “ON” or the “STANDBY” position.  
3. For the cylinder temperature retention system to  
operate, the power switch must be in the “AUTO”  
position and the mix refrigeration switch must be  
in the “STANDBY” position.  
Separate Hopper Refrigeration  
(SHR)  
This feature incorporates the use of a separate small  
refrigeration system to chill (on a limited basis) and to  
maintain the mix in the hopper to under 40_F (4.4_C)  
and assures bacterial control. To activate this system,  
place the power switch in the “AUTO” position and the  
mix refrigeration switch in the “ON” position. To oper-  
ate this system in the “STANDBY” mode, place the  
power switch in the “AUTO” position and the mix refri-  
geration switch in the “STANDBY” position.  
Figure 10  
Note: During “AUTO” operation, the orifice end of the  
tube should be inserted in the hole in the hopper.  
090526  
16  
Important: To the Operator  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To operate the “STANDBY” mode of operation:  
Cylinder Temperature Retention  
(CTR)  
Place the power switch in the “AUTO” position and the  
mix refrigeration switch in the “STANDBY” position.  
With sanitized hands, remove the feed tube. Turn it  
over and place the end without the hole into the mix  
inlet hole.  
To maintain a good quality product during long “No  
Sale” periods, it will be necessary to warm the product  
in the freezing cylinder to approximately 35_ to 40_F  
(1.7_ to 4.4_C). This will prevent overbeating and  
product breakdown. The CTR is used in conjunction  
with the SHR to insure that the mix in the freezing  
cylinder is refrigerated during the “STANDBY” mode of  
operation.  
To resume normal operation:  
Leave the power switch in the “AUTO” position and  
place the mix refrigeration switch in the “AUTO”  
position. When the unit cycles off, the product in the  
freezing cylinder will be the correct viscosity. With  
sanitized hands, remove the feed tube. Turn it over  
and place the end with the hole into the mix inlet hole.  
17  
Models 150, 152, 162, 168  
Important: To the Operator  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 6  
Operating Procedures  
The Model 150 has been selected to illustrate the  
pictured step- by- step operating procedures. All  
models in this manual are similar. They each have a  
1.5 quart (1.4 liter) capacity freezing cylinder. The mix  
flows by gravity from the hopper to the freezing  
cylinder through an feed tube.  
The Model 150 is a console model with a single spout  
door.  
The Model 152 is a counter model with a single spout  
door.  
The Model 162 is a counter model and the Model 168  
is a console model. Both have three spout doors. Two  
individual flavors are available from the end spouts,  
and an equal combination of both is dispensed through  
the center spout to create a twist effect.  
Figure 12  
For the Models 162 and 168, duplicate the procedures  
where they apply for the second freezing cylinder.  
We begin our instructions at the point where we enter  
the store in the morning and find the parts  
disassembled and laid out to air dry from the previous  
night’s cleaning.  
These opening procedures will show you how to  
assemble these parts into the freezer, sanitize them,  
and prime the freezer with fresh mix in preparation to  
serve your first portion.  
Figure 13  
Figure 14  
If you are disassembling the machine for the first time  
or need information to get to the starting point in our  
instructions, turn to page 26, “Disassembly”, and start  
there.  
Figure 11  
120501  
18  
Operating Procedures  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 3  
Assembly  
Place the large o- ring(s) into the groove(s) on the back  
of the freezer door and lubricate with Taylor Lube.  
Note: When lubricating parts, use an approved food  
grade lubricant (example: Taylor Lube).  
Step 1  
Lubricate the groove on the beater drive shaft. Withthe  
opening of the cup seal facing away from the hex end,  
slide the seal into the groove. Apply an even coat of  
lubricant to the seal and the shaft. Do not  
lubricate the hex end of the beater drive shaft.  
Figure 17  
Step 4  
Slide the front bearing(s) over the baffle rod(s) so the  
flanged edge is against the door. Place the white  
plastic guide bearing(s) on the end of the baffle rod(s).  
Do not lubricate the front bearing(s) or the guide  
bearing(s).  
Figure 15  
Step 2  
Insert the beater assembly through the rear shell  
bearing at the back of the freezing cylinder and engage  
the hex end firmly into the female socket. When  
properly seated, the beater will not protrude beyond  
the front of the freezing cylinder.  
Figure 18  
Step 5  
Slide the slotted portion of the handscrews into the  
slots in the freezer door.  
Step 6  
Figure 16  
With both hands, hold the sides of the freezer door and  
insert the baffle rod(s) into the center of the beater  
assembly(ies). The white guide bearing(s) must fit  
securely in the hole(s) of the drive shaft(s).  
Repeat this step for the second freezing cylinder on  
Models 162/168.  
120501  
19  
Models 150, 152, 162, 168  
Operating Procedures  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 7  
Step 9  
Finger- tighten the handscrews, making sure they are  
tightened equally and that the door is snug. Do not  
over- tighten the handscrews.  
Lubricate the inside of the freezer door spout(s) from  
the bottom. Insert the draw valve(s) into the freezer  
door from the bottom.  
IMPORTANT! Handscrew and door damage can  
result if the handscrews are over- tightened or if  
one handscrew is tightened more than the other.  
Step 8  
Slide the two o- rings into the grooves on the draw  
valve(s) and lubricate with Taylor Lube.  
Figure 21  
Note: The draw valve is installed correctly when the  
slotted opening in the draw valve is visible through the  
“window” of the freezer door.  
Figure 19  
Note: For the Models 162/168, install the valve seal  
in the grooves on the center draw valve and lubricate  
with Taylor Lube. This special seal will prevent mix  
from one freezing cylinder from traveling into the  
second cylinder.  
Figure 20  
Figure 22  
120501  
20  
Operating Procedures  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 10  
Step 12  
Insert the valve lifter arm through the slotted opening  
in the draw valve and align the other end with the cross  
holes of the freezer door.  
Insert the draw valve handle through the opposite  
cross hole and into the opening of the valve lifter arm.  
Hint: The draw valve handle can be assembled at  
varied vertical positions. Choose an angle which is  
comfortable for you. The draw valve must be raised  
completely when the draw valve handle is down.  
Hint: The valve lifter arm may be aligned with the left  
or right cross hole. The draw valve handle will be  
placed through the opposite cross hole of the valve  
lifter arm.  
Figure 23  
Figure 25  
Step 11  
Note: For Models 162/168, slide the o- ring onto each  
pivot pin and lubricate with Taylor Lube.  
Slide the o- ring into the groove on the draw valve  
handle and lubricate with Taylor Lube.  
Figure 24  
Figure 26  
21  
Models 150, 152, 162, 168  
Operating Procedures  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note: Models 162/168 have three draw handles.  
Slide the tip of the draw handle into the slot of the draw  
valve, starting from the right. Slide the short pivot pin  
through the far right draw handle. Slide the long pivot  
pin through the far left and middle draw handles.  
Sanitizing  
Step 1  
Prepare an approved 100 PPM sanitizing solution (ex-  
amples: Kay- 5R or Stera- SheenR). USE WARM  
WATER AND FOLLOW THE MANUFACTURER’S  
SPECIFICATIONS.  
Step 2  
Pour one gallon (3.8 liters) of the sanitizing solution  
into the hopper and allow it to flow into the freezing  
cylinder.  
Step 3  
While the solution is flowing into the freezing cylinder,  
brush- clean the mix hopper, mix level float stem, mix  
level float, mix inlet hole, and feed tube.  
Figure 27  
Step 13  
Snap the design cap(s) over the bottom of the freezer  
door spout(s).  
Figure 29  
Figure 28  
Step 14  
Lay the feed tube(s) in the bottom of the mix hopper(s).  
Figure 30  
22  
Operating Procedures  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 6  
Place an empty pail beneath the door spout and raise  
the draw valve. Draw off all of the sanitizing solution.  
When the sanitizer stops flowing from the door spout,  
lower the draw valve and place the power switch in the  
“OFF” position.  
Figure 31  
Step 4  
Press the reset button.  
Figure 34  
Note: On Models 162/168, momentarily pull down the  
center draw handle to sanitize the center door spout.  
Step 7  
With sanitized hands, stand the feed tube in the corner  
of the mix hopper. Place the mix level float on the mix  
level float stem.  
Figure 32  
Step 5  
Place the power switch in the “WASH” position. This  
will cause the sanitizing solution in the freezing  
cylinder to be agitated. Allow it to agitate for five  
minutes.  
Figure 35  
Repeat Steps 1 through 7 for the second freezing  
cylinder on Models 162/168.  
Figure 33  
23  
Models 150, 152, 162, 168  
Operating Procedures  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 3  
Priming  
Momentarily raise the draw switch paddle to activate  
the refrigeration cycle. Place the power switch in the  
“AUTO” position. When the unit cycles off, the product  
will be ready to serve.  
Prime the machine as close as possible to the time of  
first product draw.  
Step 1  
With a pail beneath the door spout, raise the draw  
valve. Fill the mix hopper with fresh mix. (Maximum  
hopper capacity is 8 quarts [7.6 liters].) Allow the mix  
to flow into the freezing cylinder. This will force out any  
remaining sanitizing solution. When full strength mix is  
flowing from the door spout, lower the draw valve.  
Note: Use only FRESH mix when priming the  
freezer.  
Figure 38  
Step 4  
Place the mix hopper cover in position.  
Repeat Steps 1 through 4 for the second freezing  
cylinder on Models 162/168.  
Figure 36  
Step 5  
Step 2  
Install the front drip tray and splash shield under the  
freezer door.  
When the mix has stopped bubbling down into the  
freezing cylinder, install the feed tube in the mix inlet  
hole. Make sure the small hole in the feed tube is down.  
Figure 37  
Figure 39  
24  
Operating Procedures  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 6  
Note: If local health codes DO NOT permit the use  
of rerun, the product must be discarded. Follow the  
instructions in the previous step, except drain the  
product into a pail and properly discard the mix.  
Slide the rear drip pan into the hole in the side panel.  
ALWAYS FOLLOW LOCAL HEALTH CODES.  
Repeat Steps 1 through 3 for the second freezing  
cylinder on Models 162/168.  
Rinsing  
Step 1  
Figure 40  
Pour one gallon (3.8 liters) of cool, clean water into the  
mix hopper. With the brushes provided, scrub the mix  
hopper, the mix level float stem and the mix inlet hole.  
Closing Procedure  
Step 2  
With a pail beneath the door spout, place the power  
switch in the “WASH” position and raise the draw  
valve. Drain all the rinse water from the freezing  
cylinder. When the rinse water stops flowing from the  
door spout, lower the draw valve and place the power  
switch in the “OFF” position.  
To disassemble the Models 150/152/162/168, the  
following items will be needed:  
S
S
S
S
S
Two cleaning pails  
Sanitized stainless steel rerun can with lid  
Necessary brushes (provided with freezer)  
Cleaner  
Repeat this procedure until the rinse water being  
drawn from the freezing cylinder is clear.  
Single service towels  
Repeat Steps 1 and 2 for the second freezing cylinder  
on Models 162/168.  
Draining Product From the  
Freezing Cylinder  
Cleaning  
Step 1  
Step 1  
Place the power switch in the “OFF” position as far  
ahead of cleaning time as possible. This will allow  
frozen product to soften for easier cleaning.  
Prepare an approved cleaning solution (examples:  
Kay- 5R or Stera- SheenR). USE WARM WATER  
AND FOLLOW THE MANUFACTURER’S SPECIFIC-  
ATIONS.  
Step 2  
Lift the hopper cover. Remove the feed tube and mix  
level float. Take them to the sink for cleaning.  
Step 2  
Pour one gallon (3.8 liters) of the cleaning solution into  
the mix hopper and allow it to flow into the freezing  
cylinder.  
Step 3  
If local health codes permit the use of rerun, place  
a sanitized, NSF approved stainless steel rerun  
container beneath the door spout. Place the power  
switch in the “WASH” position and raise the draw  
valve. When all the product stops flowing from the door  
spout, lower the draw valve and place the power switch  
in the “OFF” position. Place a sanitized lid on the rerun  
container and place it in the walk- in cooler.  
(Note: For additional information regarding the proper  
use of rerun, see item 5 on page 27.)  
Step 3  
While the solution is flowing into the freezing cylinder,  
brush- clean the mix hopper, mix level float stem and  
mix inlet hole.  
Step 4  
Place the power switch in the “WASH” position. This  
will cause the cleaning solution in the freezing cylinder  
to agitate.  
140721  
25  
Models 150, 152, 162, 168  
Operating Procedures  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step 5  
Note: To remove the o- rings, use a single service  
towel to grasp the o- ring. Apply pressure in an upward  
direction until the o- ring pops out of its groove. With  
the other hand, push the top of the o- ring forward, and  
it will roll out of the groove and can be easily removed.  
If there is more than one o- ring to be removed, always  
remove the rear o- ring first. This will allow the o- ring  
to slide over the forward rings without falling into the  
open grooves.  
Place an empty pail beneath the door spout and raise  
the draw valve. Draw off all the cleaning solution.  
When the solution stops flowing from the door spout,  
lower the draw valve and place the power switch in the  
“OFF” position.  
Repeat Steps 1 through 5 for the other side of the  
freezer on Models 162/168.  
Models 162/168: From the freezer door, remove  
design caps, pivot pins, draw handles, draw valves,  
and the center draw valve. Remove all o- rings.  
Disassembly  
Step 4  
Remove the front bearing(s), and guide bearing(s)  
from the back of the freezer door.  
Step 1  
Step 5  
Make sure the power switch is in the OFF  
position. Failure to follow this instruction may result  
in severe personal injury from hazardous moving  
parts.  
Return to the freezer with a small amount of cleaning  
solution. With the black bristle brush, brush clean the  
rear shell bearing(s) at the back of the freezing  
cylinder(s).  
Step 2  
Remove the handscrews and the freezer door.  
Remove the beater assembly(ies) from the freezing  
cylinder(s) and take these parts to the sink for  
cleaning.  
Step 3  
Remove the front drip tray and the splash shield from  
the freezer. Take them to the sink for cleaning.  
Brush Cleaning  
Figure 41  
Step 1  
Step 6  
Prepare a sink with an approved cleaning solution.  
USE WARM WATER AND FOLLOW THE MANUFAC-  
TURER’S SPECIFICATIONS.  
Remove the rear drip pan from the side panel and take  
it to the sink for cleaning.  
Note: If the drip pan is filled with an excessive amount  
of mix, this is an indication that the drive shaft cup seal  
of the beater assembly should be replaced or properly  
lubricated.  
IMPORTANT:  
Follow label directions, as too  
STRONG of a solution can cause parts damage, while  
too MILD of a solution will not provide adequate  
cleaning.) Make sure all brushes provided with the  
freezer are available for brush cleaning.  
Step 7  
Thoroughly brush clean all disassembled parts in the  
cleaning solution. Make sure all lubricant and mix film  
is removed. Take particular care to brush clean the  
draw valve core(s) in the freezer door. Place all the  
cleaned parts on a clean, dry surface to air dry  
overnight.  
Step 2  
Remove the cup seal(s) from the drive shaft(s) of the  
beater assembly(ies).  
Step 3  
From the freezer door, remove the design cap, draw  
valve handle, valve lifter arm, and draw valve. Remove  
all o- rings.  
Step 8  
Wipe clean all exterior surfaces of the freezer.  
120529  
26  
Operating Procedures  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 7  
Important: Operator Checklist  
j 5. IF LOCAL HEALTH CODES PERMIT THE  
During Cleaning and Sanitizing  
USE OF RERUN, make sure the mix rerun is  
stored in a sanitized, covered stainless steel  
container and is used the following day. DO  
NOT prime the machine with rerun. When using  
rerun, skim off the foam and discard. Mix the  
rerun with fresh mix in a ratio of 50/50 during the  
day’s operation.  
ALWAYS FOLLOW LOCAL HEALTH CODES.  
Cleaning and sanitizing schedules are governed  
by federal, state, or local regulatory agencies, and  
must be followed accordingly. If the unit has a  
“Standby mode”, it must not be used in lieu of  
proper cleaning and sanitizing procedures and  
frequencies set forth by the ruling health  
authority. The following check points should be  
stressed during the cleaning and sanitizing  
operations.  
j 6. On a designated day of the week, run the mix as  
low as feasible and discard after closing. This  
will break the rerun cycle and reduce the  
possibility of high bacteria and coliform counts.  
j 7. Properly prepare the cleaning and sanitizing  
solutions. Read and follow label directions  
carefully. Too strong of a solution may damage  
the parts and too weak of a solution will not do  
an adequate job of cleaning or sanitizing.  
j 8. The temperature of the mix in the mix hopper  
and walk- in cooler should be below 40_F.  
(4.4_C.).  
CLEANING AND SANITIZING MUST BE  
PERFORMED DAILY.  
Troubleshooting Bacterial Count  
Regular Maintenance Checks  
j 1. Thoroughly clean and sanitize the machine  
regularly, including complete disassembly and  
brush cleaning.  
j 1. Check the rear shell bearing for signs of wear  
(excessive mix leakage in rear drip pan) and be  
certain it is properly cleaned.  
j 2. Use all brushes supplied for thorough cleaning.  
The brushes are specially designed to reach all  
mix passageways.  
j 2. Using a screwdriver and cloth towel, keep the  
rear shell bearing and the female hex drive  
socket clean and free of lubricant and mix  
deposits.  
j 3. Use the smaller, white bristle brush to clean the  
mix inlet hole which extends from the mix  
hopper down to the rear of the freezing cylinder.  
j 3. Dispose of o- rings or seals if they are worn,  
torn, or fit too loosely, and replace with new  
ones.  
j 4. Use the black bristle brush to thoroughly clean  
the rear shell bearing located at the rear of the  
freezing cylinder. Be sure to have a generous  
amount of cleaning solution on the brush.  
j 4. Follow all lubricating procedures as outlined in  
“Assembly”.  
27  
Models 150, 152, 162, 168  
Important: Operator Checklist  
Download from Www.Somanuals.com. All Manuals Search And Download.  
j 5. If your machine is air cooled, check the  
condenser for an accumulation of dirt and lint.  
A dirty condenser will reduce the efficiency and  
capacity of the machine. Condensers should be  
cleaned monthly with a soft brush. Never use  
screwdrivers or other metal probes to clean  
between the fins. Failure to comply may result  
in electrocution.  
Winter Storage  
If the place of business is to be closed during the winter  
months, it is important to protect the freezer by  
following certain precautions, particularly if the  
building is subject to freezing conditions.  
Disconnect the freezer from the main power source to  
prevent possible electrical damage.  
Note: For machines equipped with an air filter,  
it will be necessary to vacuum clean the filters  
on a monthly schedule.  
Your local Taylor distributor can perform this servicefor  
you.  
j 6. On the auxiliary refrigeration system, check the  
condenser for accumulation of dirt and lint. A  
dirty condenser will reduce the refrigeration  
capacity of the mix hopper. Condensers must  
be cleaned monthly with a soft brush. Never  
use screwdrivers or other metal probes to clean  
between the fins. Failure to comply may result  
in electrocution.  
Wrap detachable parts of the freezer such as the  
beater assembly and freezer door, and place them in  
a protected dry place. Rubber trim parts and gaskets  
can be protected by wrapping them with  
moisture- proof paper. All parts should be thoroughly  
cleaned of dried mix or lubrication accumulations  
which attract mice and other vermin.  
28  
Important: Operator Checklist  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 8  
Troubleshooting Guide  
PROBLEM  
PROBABLE CAUSE  
REMEDY  
PAGE  
REF.  
24  
1. No product being  
dispensed.  
a. The power switch is in the  
“OFF” position.  
a. Place the power switch in  
the “AUTO” position.  
24  
b. The mix level is  
inadequate in the mix  
hopper.  
b. Fill the mix hopper with  
mix.  
16  
16  
16  
c. The beater motor  
overloaded.  
c. Reset the freezer.  
d. The unit is unplugged at  
the wall receptacle.  
d. Plug in the power cord.  
Press the reset button.  
e. The circuit breaker is  
tripped or the fuse is  
blown.  
e. Place the circuit breaker in  
the “ON” position, or  
replace the fuse. Press  
the reset button.  
19  
- - -  
16  
f. The freezer door is  
incorrectly assembled.  
f. See “Operating  
Procedures” for proper  
installation.  
g. Product is being drawn off  
in excess of the freezer’s  
capacity.  
g. Stop drawing product and  
allow the unit to recover.  
2. The machine will not  
operate in the “AUTO”  
mode.  
a. The unit is unplugged.  
a. Plug in the power cord;  
press the reset button.  
24  
b. The refrigeration system is b. On T.Q.C. units,  
momentarily raise the  
draw switch to activate the  
refrigeration system.  
not activated.  
16  
16  
c. The circuit breaker is  
tripped, or the fuse is  
blown.  
c. Place the circuit breaker in  
the “ON” position, or  
replace the fuse. Press  
the reset button.  
d. The beater motor  
overloaded, causing a loss  
of power to the power  
switch.  
d. Reset the freezer.  
16  
3. The product is too stiff.  
a. The temperature control  
or the T.Q.C. is set too  
cold.  
a. Adjust the temperature  
control. Do not set the  
temperature colder than  
18_F (- 8_C). If T.Q.C.,  
contact service technician.  
29  
Models 150, 152, 162, 168  
Troubleshooting Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM  
PROBABLE CAUSE  
REMEDY  
PAGE  
REF.  
16  
4. The product is too soft.  
a. The temperature control  
or the T.Q.C. is set too  
warm.  
a. Adjust the temperature  
control. If T.Q.C., contact  
service technician.  
24  
b. The feed tube is not  
installed.  
b. Install the feed tube in the  
mix inlet hole at the  
bottom of the mix hopper.  
- - -  
19  
c. Out- drawing the freezer’s  
capacity.  
c. Two 4 oz. (113.4 gram)  
servings in one minute.  
5. The freezing cylinder walls a. Operating freezer without  
a. Install the front bearing on  
the freezer door.  
are scored.  
the front bearing on the  
freezer door.  
- - -  
32  
b. The gear unit or the direct  
drive is out of alignment.  
b. Contact service  
technician.  
6. Excessive leakage in rear  
drip pan.  
a. A worn or defective o- ring  
is on the beater drive  
shaft.  
a. Replace o- rings every 3  
months.  
- - -  
19  
b. The rear shell bearing is  
worn.  
b. Contact service  
technician.  
c. Incorrect lubricant was  
used.  
c. Use food grade lubricant  
(example: Taylor Lube).  
19  
d. Inadequate lubrication of  
beater drive shaft.  
d. Lubricate the beater drive  
shaft properly.  
20  
7. The draw valve is leaking.  
a. Incorrect lubricant was  
used.  
a. Use food grade lubricant  
(example: Taylor Lube).  
32  
b. Worn or defective o- rings  
are on the draw valve.  
b. Replace o- rings every 3  
months.  
20  
c. Inadequate lubrication of  
draw valve.  
c. Lubricate the draw valve  
properly.  
24  
8. Product is not feeding into  
the freezing cylinder.  
a. The mix level is  
inadequate in the mix  
hopper.  
a. Fill the mix hopper with  
mix.  
16  
b. The mix inlet hole is  
frozen.  
b. Contact service  
technician.  
30  
Troubleshooting Guide  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM  
PROBABLE CAUSE  
REMEDY  
PAGE  
REF.  
- - -  
9. The unit goes out on  
overload excessively.  
a. There are too many  
appliances plugged into  
the circuit.  
a. A separate 20 amp.  
circuit is needed for the  
freezer to operate  
properly.  
- - -  
b. An extension cord has  
been placed between the  
power cord and the wall  
receptacle.  
b. If the extension cord is  
used, it must match the  
power cord in size of  
circuit ampacity.  
20 / 32  
10. Models 162 and 168:  
Mix from one freezing  
cylinder bleeds over to the  
second cylinder.  
a. The center draw valve  
seal is worn, or is  
a. Lubricate properly and  
replace seal every 3  
months.  
improperly lubricated.  
31  
Models 150, 152, 162, 168  
Troubleshooting Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 9  
Parts Replacement Schedule  
PART DESCRIPTION  
EVERY 3  
MONTHS  
EVERY 6  
MONTHS  
ANNUALLY  
QTY.  
150/152 162/168  
Beater Drive Shaft Cup Seal  
Freezer Door O- Ring  
X
X
X
X
X
X
X
X
1
1
1
1
2
1
-
2
2
2
2
4
-
Freezer Door Front Bearing  
Freezer Door Guide Bearing  
Draw Valve O- Ring  
Draw Valve Handle O- Ring  
Center Draw Valve Seal  
Pivot Pin O- Ring  
1
2
1
-
Black Bristle Brush, 1” x 2”  
Inspect & Replace  
if Necessary  
Minimum  
Minimum  
Minimum  
Minimum  
1
Double Ended Brush  
Inspect & Replace  
if Necessary  
1
1
1
1
1
1
White Bristle Brush, 1” x 2”  
White Bristle Brush, 3” x 7”  
Inspect & Replace  
if Necessary  
Inspect & Replace  
if Necessary  
120501  
32  
Parts Replacement Schedule  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 10 Limited Warranty on Equipment  
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS  
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited  
warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)  
to the original purchaser only.  
LIMITED WARRANTY  
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and  
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to  
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,  
will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for  
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for  
a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed  
below and on the reverse (if any) of this document.  
Product  
Soft Serve  
Part  
Limited Warranty Period  
Five (5) years  
Insulated shell assembly  
Frozen Yogurt  
Shakes  
Refrigeration compressor  
(except service valve)  
Five (5) years  
Beater motors  
Two (2) years  
Two (2) years  
Two (2) years  
Smoothies  
Frozen Beverage  
Batch Desserts  
Beater drive gear  
Printed circuit boards and  
Softech controls beginning  
with serial number H8024200  
Parts not otherwise listed in  
this table or excluded below  
One (1) year  
LIMITED WARRANTY CONDITIONS  
1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins  
ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of  
purchase may be required at time of service.  
2. This limited warranty is valid only if the Product is installed and all required service work on the Product is  
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are  
used.  
3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in  
the Taylor Operator’s Manual.  
4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.  
5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.  
LIMITED WARRANTY EXCEPTIONS  
This limited warranty does not cover:  
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of  
defective parts, replacement parts, or new Products.  
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning  
of condensers.  
131122  
33  
Models 150, 152, 162, 168  
Limited Warranty on Equipment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.  
4. External hoses, electrical power supplies, and machine grounding.  
5. Parts not supplied or designated by Taylor, or damages resulting from their use.  
6. Return trips or waiting time required because a service technician is prevented from beginning warranty  
service work promptly upon arrival.  
7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,  
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including  
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning  
supplies.  
8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake  
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,  
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or  
water supply specification of the Product; or components repaired or altered in any way so as, in the  
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.  
9. Any Product purchased over the Internet.  
10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the  
inadequacy or interruption of electrical service.  
11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.  
12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will  
void this limited warranty.  
13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.  
14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY  
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential  
damages, so this limitation may not apply to you.  
This limited warranty gives you specific legal rights, and you may also have other rights which vary from  
jurisdiction to jurisdiction.  
LIMITATION OF WARRANTY  
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS  
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE  
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE  
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL  
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,  
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS  
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED  
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.  
LEGAL REMEDIES  
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or  
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other  
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or  
remedies.  
Taylor Company  
a division of Carrier Commercial Refrigeration, Inc.  
750 N. Blackhawk Blvd.  
Rockton, IL 61072, U.S.A.  
34  
Limited Warranty on Equipment  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 11  
Limited Warranty on Parts  
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS  
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited  
warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally  
(the “Parts”) to the original purchaser only.  
LIMITED WARRANTY  
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service  
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails  
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service  
agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no  
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited  
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions  
listed below and on the reverse (if any) of this document.  
Part’s Warranty Class Code or Part  
Class 103 Parts¹  
Limited Warranty Period  
Three (3) months  
Class 212 Parts²  
Twelve (12) months  
Twelve (12) months  
No warranty  
Class 512 Parts  
Class 000 Parts  
Taylor Part #072454 (Motor- 24VDC *C832/C842*)  
Four (4) years  
LIMITED WARRANTY CONDITIONS  
1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required  
at time of service.  
2. This limited warranty is valid only if the Part is installed and all required service work in connection with the  
Part is performed by an authorized Taylor distributor or service agency.  
3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation  
location in the unit of original installation.  
4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in  
the Taylor Operator’s Manual.  
5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.  
6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate  
Taylor Limited Warranty on freezer or grill equipment.  
7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this  
limited warranty.  
1, 2  
Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1  
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor  
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.  
131122  
35  
Models 150, 152, 162, 168  
Limited Warranty on Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY EXCEPTIONS  
This limited warranty does not cover:  
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of  
defective Parts, replacement Parts, or new Parts.  
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning  
of condensers or carbon and grease buildup.  
3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including  
the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper  
assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but  
not limited to the platen and plate, sides of the shroud or top of the shroud.  
4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or  
in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or  
other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials  
or cleaning processes not approved for use by Taylor.  
5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any  
release sheets and clips for the Product’s upper platen assembly.  
6. External hoses, electrical power supplies, and machine grounding.  
7. Parts not supplied or designated by Taylor, or damages resulting from their use.  
8. Return trips or waiting time required because a service technician is prevented from beginning warranty  
service work promptly upon arrival.  
9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,  
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including  
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning  
supplies.  
10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake  
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,  
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or  
water supply specification of the unit in which a part is installed; or Parts or the units in which they are  
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or  
normal wear or deterioration.  
11. Any Part purchased over the Internet.  
12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the  
inadequacy or interruption of electrical service.  
13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.  
14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is  
installed will void this limited warranty.  
15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.  
16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY  
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential  
damages, so this limitation may not apply to you.  
This limited warranty gives you specific legal rights, and you may also have other rights which vary from  
jurisdiction to jurisdiction.  
36  
Limited Warranty on Parts  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITATION OF WARRANTY  
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS  
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE  
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE  
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR  
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,  
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS  
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED  
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.  
LEGAL REMEDIES  
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or  
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other  
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.  
Taylor Company  
a division of Carrier Commercial Refrigeration, Inc.  
750 N. Blackhawk Blvd.  
Rockton, IL 61072, U.S.A.  
37  
Models 150, 152, 162, 168  
Limited Warranty on Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 12  
Parts List  
+ Available Separately  
120501  
38  
Parts List  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
Models 150, 152, 162, 168  
Parts List  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
110517  
40  
Parts List  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
120501  
Models 150, 152, 162, 168  
Parts List  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
42  
Parts List  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
110804  
Models 150, 152, 162, 168  
Parts List  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
44  
Parts List  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
Models 150, 152, 162, 168  
Parts List  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
+ Available Separately  
46  
Parts List  
Models 150, 152, 162, 168  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BLK  
BLK  
BLK  
BLK  
BLK  
BRN  
RED/WHT  
BLACK  
BRN/WHT  
BRN  
WHT  
WHT  
WHT  
150/152  
050416-12  
11/12/13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BLK  
BLK  
WHT/BLK  
BLK  
BLK  
BLK  
BRN  
RED/WHT  
BLK  
BLK  
BLK  
BRN  
BLU  
WHT  
WHT  
WHT  
150/152  
050416-27  
11/12/13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BRN  
BLK  
BLK  
WHT/BLK  
BLK  
BLK  
BLK  
BLK  
BRN  
RED/WHT  
BLACK  
WHT  
WHT  
WHT  
GRN/YEL  
GRN/YEL  
GRN/YEL  
150/152  
050416-40  
11/12/13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
L1  
N
LEFT  
POWER SUPPLY  
WHT  
WHT  
WHT  
BLK  
WHT  
WHT  
L1  
T1  
BLK  
T2  
L2  
M
LEFT MAIN  
COMPRESSOR  
CONTACTOR  
LEFT MAIN  
COMPRESSOR  
(FIG. 3)  
LEFT MAIN  
COMPRESSOR  
CONTACTOR  
WHT  
BLK CORD  
BLK CORD  
M
MAIN CONDENSER FAN  
(ONE (1) FAN MOTOR ONLY FOR MODEL 168. RUN CAPACITOR APPLIES TO MODEL 168 ONLY.)  
BLK  
WHT/ORN  
WHT/ORN  
13  
14  
LEFT MAIN  
COMPRESSOR  
CONTACTOR  
BRN  
WHT  
WHT  
WHT/GRA  
13  
14  
BLK/WHT (M168)  
BLACK CORD (M162)  
WHT (M168)  
BLK CORD (M162)  
M
RIGHT MAIN  
COMPRESSOR  
CONTACTOR  
MAIN CONDENSER FAN  
BLK  
YEL  
WHT  
WHT  
YEL  
MIX LOW TRANSFORMER  
(FIG. 1, FIG. 2)  
LEFT COMPRESSOR  
CYCLE TIMER  
DOM - 14 MIN.  
BLK  
RED  
BLK  
PUR/WHT  
RED  
INPUT  
LOAD  
3
BLU  
10K  
5
LEFT MIX LOW  
SWITCH  
LEFT MIX  
LOW LIGHT  
GRA/WHT  
1
A
B
LEFT  
VARISTOR  
NC  
NO  
GRA/WHT  
PUR  
COMPRESSOR  
ENABLE  
RELAY  
4
5
6
1
2
3
BLK  
RED  
BLK  
VISCOSITY CONTROL  
(FIG. 5)  
BLK/WHT  
C
YEL  
4
6
RIGHT MIX LOW  
SWITCH  
NC RIGHT MIX  
LOW LIGHT  
2
1
LEFT DRAW SWITCH  
L3 T3  
C
C
AUTO  
OFF  
COMPRESSOR  
5
6
1
ENABLE  
RELAY  
NO  
NC  
GRA/WHT  
GRA/WHT  
YEL  
3
2
2
5
WASH  
LEFT MAIN COMPRESSOR CONTACTOR  
3
4
AUTO  
1
AUTO  
OFF  
OFF  
RED  
2
NO BLU  
BLU  
STANDBY  
ORN/WHT  
BLK  
CORD  
BLK  
4
3
4
CORD  
WASH  
BLK/WHT  
6
AUTO  
LEFT LATCHING RELAY  
WHT/GRA  
LEFT CONTROL SWITCH  
LEFT HPCO SWITCH  
OFF  
LEFT STIR CYCLE TIMER  
5 SEC. ON-120 SEC. OFF  
WHT/GRA  
YEL  
WHT/GRA  
5
8
STANDBY  
LEFT STANDBY  
TEMPERATURE CONTROL SWITCH  
6
7
1
2
3
7
AUTO  
AUTO  
OFF  
8
OFF  
LEFT COMPRESSOR  
START TIME DELAY  
DOM - 2 SEC.  
INPUT  
1
WHT  
STANDBY  
9
BRN/WHT  
9
WASH  
ORN  
WHT  
LEFT STIR CYCLE RELAY  
STANDBY/SHR  
SWITCH  
A
B
LOAD  
3
NC  
1
AUTO  
OFF  
12 STBY  
C
7
10  
BLK/WHT  
WHT  
BLK/WHT  
NO  
4
11  
M
SHR  
COMPRESSOR  
(FIG. 4)  
NC  
2
C
8
WHT/BLK  
SHR TEMPERATURE  
CONTROL SWITCH  
NO  
5
BRN  
BLK/WHT  
WHT  
M
NC  
SHR  
GRA/WHT  
3
C
9
CONDENSER FAN  
NO  
6
WHITE  
LEFT LIQUID LINE SOLENOID  
WHT  
WHT  
BRN/WHT  
LEFT STIR  
CYCLE RELAY  
GRN/YEL  
RED/BLK  
WHT/RED  
A1  
A2  
LEFT MAIN COMPRESSOR CONTACTOR  
WHITE/RED  
WHT/BLK  
A
B
LEFT LATCHING RELAY  
PUSH BUTTON SWITCH  
LEFT LATCHING RELAY  
LEFT BEATER MOTOR  
(FIG. 6)  
LEFT COMPRESSOR "ON" LIGHT  
(OPTION)  
L1  
N
RIGHT  
POWER SUPPLY  
WHT  
WHT  
WHT  
WHT  
BLK  
BLK  
L1  
T1  
WHT  
T2  
L2  
M
GRN/YEL  
RIGHT MAIN  
COMPRESSOR  
CONTACTOR  
RIGHT MAIN  
COMPRESSOR  
(FIG. 3)  
RIGHT MAIN  
COMPRESSOR  
CONTACTOR  
WHITE  
WHT  
BLUE  
RIGHT  
VISCOSITY CONTROL  
(FIG. 5)  
4
5
6
1
2
3
PUR/WHT  
3
RIGHT COMPRESSOR  
5
CYCLE TIMER  
DOM - 14 MIN.  
1
INPUT  
LOAD  
4
6
2
10K  
NC  
GRA/WHT  
1
A
B
C
C
AUTO  
OFF  
VARISTOR  
5
6
1
NC  
NO  
GRA/WHT  
PUR  
COMPRESSOR  
ENABLE  
RELAY  
NO  
NC  
COMPRESSOR  
ENABLE  
RELAY  
3
2
2
5
C
YEL  
WASH  
3
4
AUTO  
OFF  
RIGHT DRAW SWITCH  
L3 T3  
NO  
BLU  
BLUE  
BLK  
CORD  
BLK  
CORD  
4
GRA/WHT  
WASH  
6
RIGHT LATCHING RELAY  
RIGHT MAIN COMPRESSOR CONTACTOR  
ORN/WHT  
RIGHT HPCO SWITCH  
BRN/WHT  
RIGHT CONTROL SWITCH  
RIGHT COMPRESSOR  
START TIME DELAY  
DOM - 2 SEC.  
INPUT  
1
RIGHT STIR CYCLE TIMER  
5 SEC. ON-120 SEC. OFF  
NC  
LOAD  
3
1
C
7
RIGHT STANDBY  
1
2
3
NO  
4
TEMPERATURE CONTROL SWITCH  
NC  
2
ORN/WHT  
WHT  
C
8
WHT/BLK  
BRN  
NO  
5
ORN  
WHT  
A
B
NC  
RIGHT STIR  
CYCLE RELAY  
3
C
9
NO  
6
WHT  
WHT  
BRN/WHT  
GRN/YEL  
RIGHT STIR  
CYCLE RELAY  
RIGHT LIQUID LINE SOLENOID  
WHT/RED  
RED/BLK  
A1  
A2  
RIGHT BEATER MOTOR  
(FIG. 6)  
RIGHT MAIN COMPRESSOR CONTACTOR  
WHT/RED  
WHT/BLK  
WHT  
A
B
RIGHT LATCHING RELAY  
RIGHT LATCHING RELAY  
PUSH BUTTON SWITCH  
BLACK  
BLACK  
YELLOW  
RIGHT COMPRESSOR "ON" LIGHT (OPTION)  
NOTES:  
WHT  
1
1. L1 SUPPLY VOLTAGE  
2. NC CONTACT  
YELLOW  
WHITE  
1
WHT  
L1  
3. NC CONTACT  
4. L2 SUPPLY VOLTAGE  
5. LINE - BEATER MOTOR CURRENT  
6. LOAD - BEATER MOTOR CURRENT  
MIX LOW TRANSFORMER  
1) FOR CCW ROTATION OF A.O. SMITH  
GRN/YEL  
BEATER MOTOR CONNECT INTERNAL  
RED TO TERMINAL 4 & INTERNAL  
BLACK TO TERMINAL 2.  
BLACK  
BLACK  
WHT/RED  
WHITE/RED  
5
MIX LOW PCB A.  
W/CHIME/SNOOZE  
2
T8  
WHT/RED  
VISCOSITY CONTROL TERMINALS  
4
RED  
FIG. 5  
(INTERNAL)  
2) FOR "CCW" ROTATION OF GE/RBC  
BEATER MOTOR CONNECT  
INTERNAL BLUE TO TERMINAL 5 &  
INTERNAL YELLOW TO TERMINAL 2.  
T5  
BLACK  
(INTERNAL)  
BROWN  
2
L2  
PURPLE  
RED  
4
BRN  
2
BRN  
SILENCE PUSH  
BUTTON SWITCH  
LEESON BEATER MOTOR  
"CCW" ROTATION  
BLACK  
BLACK  
GE/RBC  
A. O. SMITH  
.5 HP BEATER MOTOR  
(024839-27  
BEATER MOTOR  
"CCW" ROTATION  
(SEE NOTE #2)  
RED  
YELLOW  
YELLOW  
FIG. 6  
BLACK  
BLACK  
YEL  
(SEE NOTE #1)  
MIX LOW TRANSFORMER  
LEFT MIX  
OUT SWITCH  
LEFT MIX  
OUT LIGHT  
PTC  
MAIN WINDING  
START  
WINDING  
BLACK  
GREEN  
BLACK  
BLACK  
BLACK  
BLACK  
YEL  
MIX LOW PCB A.  
W/CHIME  
LINE  
WHITE  
C
RED  
LEFT MIX  
LOW SWITCH  
LEFT MIX  
LOW LIGHT  
INTERNAL  
OVERLOAD  
BROWN  
BLACK  
RED  
2
S
YEL  
5
BLACK  
L
N
RIGHT MIX  
OUT SWITCH  
BLACK  
BLACK  
RELAY  
4
RED  
LEFT MIX  
RIGHT MIX  
OUT LIGHT  
C
RUN  
CAPACITOR  
1
LEFT MIX  
LOW LIGHT  
INTERNAL  
BLACK  
BLACK  
YEL  
LOW SWITCH  
R
BLUE  
162/168  
050205-12  
11/12/13  
BLACK  
BLACK  
RED  
RIGHT MIX  
LOW SWITCH  
RIGHT MIX  
LOW LIGHT  
BLACK  
L1  
COMPRESSOR WIRING  
N
RIGHT MIX  
LOW SWITCH  
WINDING  
PROTECTOR  
(INTERNAL)  
RIGHT MIX  
LOW LIGHT  
START  
CAPACITOR  
MODELS WITH MIX OUT LIGHT,  
MIX LOW LIGHT, W/AUDIBLE MIX  
BLEED RESISTOR  
OUT CHIME AND PUSH BUTTON SILENCE  
MODELS WITH CHIME OPTION  
TECUMSEH COMPRESSOR WIRING  
(MODEL TL2A <OR> TL2.5F W/LST)  
FIG. 1  
FIG. 2  
FIG. 3  
FIG. 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES:  
1. ONE (1) FAN ONLY ON MODEL  
168. RUN CAPACITOR APPLIES  
TO MODEL 168 ONLY.  
FIG. 1  
START RELAY  
(047702-27)  
START CAPACITOR  
(047703)  
11  
L1  
10  
13  
12  
14  
L2  
STANDBY  
TEMP  
START WINDING  
CONTROL  
(L)  
MAIN WINDING  
3PDT  
SHR SW.  
WINDING PROTECTOR  
(INTERNAL)  
BLACK/WHITE STRIPE  
WHITE/BLK STR  
STANDBY  
9
7
6
4
3
1
COMPRESSOR WIRING  
(MODEL TL3G W/HST)  
8
5
2
BROWN/WHT STR  
AUTO  
COMP.  
(SEE FIG. 1)  
STANDBY  
WHITE/GRAY STR  
TEMP.  
M
CONTROL  
AUTO  
BLACK/WHT STR  
WHITE  
STANDBY  
STANDBY  
TEMP  
M
AUTO  
CONTROL  
(R)  
FAN  
PURPLE/WHT STR  
WHITE  
1
BLACK  
BLACK  
T8  
T5  
WHT./RED STR.  
SEE DETAIL "A"  
FOR MODELS W/"CHIME"  
OPTION  
2
TOGGLE SW.  
WASH  
BROWN  
BLACK  
YELLOW  
BLACK  
4
YELLOW  
BROWN  
AUTO  
WASH  
LEESON BEATER MOTOR  
CONNECTIONS  
YEL.  
YEL.  
DRAW SWITCH  
REF  
VISCOSITY  
CONTROL  
MIX LOW  
MIX LOW  
LIGHT (L)  
NC  
C
SW (L)  
AUTO  
BLUE  
NO  
WHITE  
4
5
6
1
2
MIX LOW  
SW (R)  
MIX LOW  
LIGHT (R)  
BLACK/WHT  
NC  
C
BLACK  
BLK/WHT  
BLACK  
RED  
NO  
PURPLE/WHITE STR  
TIMER  
BLUE  
CONTACTOR  
BROWN/WHT STR  
MIX  
LOW  
SW  
MIX  
LOW  
SW  
ORANGE  
GREEN  
13  
14  
BLACK  
PURPLE  
GREEN/YELLOW STR  
L3  
T3  
WHITE/ORANGE STR  
BLACK  
WHITE  
MIX  
LOW  
LIGHT  
MIX  
LOW  
LIGHT  
M
L2  
L1  
T2  
T1  
FAN  
BLACK  
BLACK  
BLACK  
GREEN/YELLOW STR  
M
DETAIL "A"  
BLACK  
FAN  
MODELS W/"CHIME"  
OPTION  
(NOTE 1)  
H.P.  
SWITCH  
C
INTERNAL  
OVERLOAD  
COMPRESSOR  
R
S
BLACK  
4
2
3
1
PUSH  
BUTTON  
BLACK  
BLACK  
BLACK  
6
BLACK  
BLACK  
COMP. "ON"  
LIGHT LEFT  
OPTIONAL  
RELAY  
YELLOW  
RED  
BROWN  
5
6
4
2
1
5
BLUE  
MIX  
OUT  
SW  
MIX  
LOW  
SW  
MIX  
OUT  
SW  
MIX  
LOW  
SW  
EQUIPMENT  
GROUND  
ORANGE  
PURPLE  
BROWN  
A
B
M
BLACK  
RUN  
CAP.  
START  
CAP.  
WHITE/BLACK STR  
BEATER  
MIX  
OUT  
LIGHT  
MIX  
LOW  
LIGHT  
MIX  
OUT  
LIGHT  
MIX  
LOW  
LIGHT  
BLACK  
RELAY  
DPDT  
WHITE  
SOL.  
WHITE  
BLACK  
BLACK  
MIX LOW AND MIX OUT LIGHT OPTION  
W/AUDIBLE MIX OUT ALARM AND PUSH  
BUTTON SILENCE  
BLACK  
TOGGLE SW.  
WASH  
WHT/ORANGE STR  
DRAW SWITCH  
BROWN  
AUTO  
WASH  
BROWN/WHT STR  
BLUE/WHT STR  
PURPLE/WHT STR  
NC  
C
L2  
L1  
REF  
AUTO  
BLUE  
VISCOSITY  
CONTROL  
NO  
EQUIPMENT  
GROUND  
LEFT SIDE  
POWER  
WHITE  
4
5
6
1
2
3
BLACK/WHT  
VISCOSITY CONTROL  
NC  
C
BLACK/WHT  
1. L1  
NO  
2. N.C. CONTACT  
3. N.C. CONTACT  
4. L2  
5. LINE  
6. LOAD  
PURPLE/WHITE STR  
CONTACTOR  
BROWN/WHT STR  
13  
14  
PURPLE  
L3  
T3  
TIMER  
L2  
L1  
T2  
T1  
BLACK  
BLACK  
BLACK  
GREEN/YELLOW STR  
BLACK  
BLACK  
H.P.  
SWITCH  
C
INTERNAL  
OVERLOAD  
COMPRESSOR  
R
S
BLACK  
4
2
3
1
BLK  
BLACK  
BLACK  
PUSH  
6
BUTTON  
COMP. "ON"  
LIGHT RIGHT  
OPTIONAL  
RELAY  
BROWN  
5
6
4
2
5
1
BROWN  
A
B
M
RUN  
CAP.  
START  
CAP.  
WHITE/BLACK STR  
BEATER  
BLACK  
RELAY  
DPDT  
WHITE  
WHITE  
SOL.  
162/168  
050205-27  
11/12/13  
EQUIPMENT  
GROUND  
RIGHT SIDE  
POWER  
L2  
L1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
L1  
N
POWER SUPPLY  
GRN/YEL  
GRN/YEL  
WHT  
GRN/YEL  
WHT  
WHT  
BLK  
BLK  
BLK  
L1  
T1  
BLK  
T2  
L2  
M
GRN/YEL  
WHT  
LEFT MAIN  
COMPRESSOR  
CONTACTOR  
LEFT MAIN  
COMPRESSOR  
(FIG. 3)  
LEFT MAIN  
COMPRESSOR  
CONTACTOR  
BLK CORD  
BLK CORD  
M
GRN/YEL  
MAIN CONDENSER FAN  
(ONE (1) FAN MOTOR ONLY FOR MODEL 168. RUN CAPACITOR APPLIES TO MODEL 168 ONLY.)  
BRN  
WHT  
LEFT COMPRESSOR "ON" LIGHT  
(OPTION)  
BLK/WHT (M168)  
BLK CORD (M162)  
WHT (M168)  
BLK CORD (M162)  
WHT  
WHT/ORN  
13  
14  
M
GRN/YEL  
LEFT MAIN  
COMPRESSOR  
CONTACTOR  
MAIN CONDENSER FAN  
WHT  
WHT  
PRP/WHT  
BRN  
WHT/GRA  
13  
14  
LEFT COMPRESSOR  
CYCLE TIMER  
DOM - 14 MIN.  
RIGHT MAIN  
COMPRESSOR  
CONTACTOR  
NC  
INPUT  
LOAD  
YEL  
YEL  
YEL  
C
C
BLU  
RED/BLK  
LEFT  
NO  
NC  
PRP/WHT  
VARISTOR  
PRP/WHT  
PRP  
4
5
6
1
2
3
BLK/WHT  
NO  
NC  
1
LEFT DRAW SWITCH  
L3 T3  
C
C
AUTO  
OFF  
5
6
1
NO  
NC  
PRP/WHT  
3
2
2
5
VISCOSITY CONTROL  
(FIG. 5)  
WASH  
LEFT MAIN COMPRESSOR CONTACTOR  
3
4
AUTO  
1
OFF  
2
AUTO  
OFF  
RED  
BLU  
ORN/WHT  
NO  
STANDBY  
BLK  
CORD  
BLK  
CORD  
4
3
WASH  
6
AUTO  
LEFT LATCHING RELAY  
WHT/GRA  
4
LEFT CONTROL SWITCH  
LEFT HPCO SWITCH  
OFF  
LEFT STIR CYCLE TIMER  
5 SEC. ON-120 SEC. OFF  
WHT/GRA  
WHT/GRA  
5
8
STANDBY  
LEFT STANDBY  
TEMPERATURE CONTROL SWITCH  
6
7
1
2
3
AUTO  
OFF  
WHT  
STANDBY  
9
ORN  
WHT  
LEFT STIR CYCLE RELAY  
BRN/WHT  
STANDBY/SHR  
SWITCH}  
A
B
NC  
1
WHT  
BLK/WHT  
C
7
M
GRN/YEL  
NO  
4
SHR  
COMPRESSOR  
(FIG. 4)  
NC  
2
SHR TEMPERATURE  
CONTROL SWITCH  
C
8
WHT/BLK  
BLK/WHT  
WHT  
M
NO  
5
BRN  
GRN/YEL  
SHR  
NC  
CONDENSER FAN  
3
C
9
NO  
6
WHT  
GRN/YEL  
BRN/WHT  
WHT  
LEFT STIR  
CYCLE RELAY  
LEFT LIQUID LINE SOLENOID  
WHT/RED  
GRN/YEL  
WHT  
RED/BLK  
A1  
A2  
LEFT MAIN COMPRESSOR CONTACTOR  
WHT/RED  
WHT/BLK  
A
B
LEFT LATCHING RELAY  
PUSH BUTTON SWITCH  
LEFT LATCHING RELAY  
LEFT BEATER MOTOR  
(FIG. 6)  
BLK  
BLK  
BLK  
L1  
T1  
BLK  
T2  
L2  
M
GRN/YEL  
RIGHT MAIN  
COMPRESSOR  
CONTACTOR  
RIGHT MAIN  
COMPRESSOR  
(FIG. 3)  
RIGHT MAIN  
COMPRESSOR  
CONTACTOR  
RIGHT COMPRESSOR "ON" LIGHT (OPTION)  
BLU  
BLK  
WHT  
WHT  
YEL  
BLK  
FUSE 1A  
RED  
YEL  
MIX LOW TRANSFORMER  
(FIG. 1, FIG. 2)  
4
5
6
1
2
3
BLK  
RED/BLK  
RIGHT  
RED  
BLK  
BLK/WHT  
PRP/WHT  
LEFT MIX LOW  
SWITCH  
LEFT MIX LOW LIGHT  
BRN  
RIGHT COMPRESSOR  
CYCLE TIMER  
DOM - 14 MIN.  
VISCOSITY CONTROL  
(FIG. 5)  
BLK  
RED  
BLK  
NC  
INPUT  
LOAD  
C
YEL  
YEL  
YEL  
RIGHT MIX LOW  
SWITCH  
RIGHT MIX LOW LIGHT  
NC  
NO  
NC  
PRP/WHT  
VARISTOR  
PRP/WHT  
PRP  
1
C
C
AUTO  
OFF  
C
5
6
1
NO  
NC  
NO  
3
2
2
5
WASH  
3
4
RIGHT DRAW SWITCH  
L3 T3  
AUTO  
OFF  
PRP/WHT  
NO  
BLU  
BLU  
BLK  
CORD  
BLK  
CORD  
4
RIGHT MAIN COMPRESSOR CONTACTOR  
ORN/WHT  
WASH  
6
RIGHT LATCHING RELAY  
RIGHT HPCO SWITCH  
BRN/WHT  
RIGHT CONTROL SWITCH  
RIGHT STIR CYCLE TIMER  
5 SEC. ON-120 SEC. OFF  
RIGHT STANDBY  
TEMPERATURE CONTROL SWITCH  
1
2
3
NC  
1
C
7
NO  
4
ORN/WHT  
WHT  
NC  
ORN  
2
WHT  
A
B
C
8
WHT/BLK  
NO  
5
BRN  
RIGHT STIR  
CYCLE RELAY  
NC  
3
C
9
NO  
6
WHT  
BRN/WHT  
WHT  
GRN/YEL  
RIGHT STIR  
CYCLE RELAY  
RIGHT LIQUID LINE SOLENOID  
WHT/RED  
RED/BLK  
RIGHT BEATER MOTOR  
(FIG. 6)  
A1  
A2  
RIGHT MAIN COMPRESSOR CONTACTOR  
WHT/RED  
WHT/BLK  
WHT  
A
B
RIGHT LATCHING RELAY  
PUSH BUTTON SWITCH  
RIGHT LATCHING RELAY  
GRN/YEL  
CONTROL  
ENCLOSURE(S)  
GRN/YEL  
NOTE:  
1) FOR CCW ROTATION OF A.O. SMITH  
BEATER MOTOR CONNECT INTERNAL  
RED TO TERMINAL 4 & INTERNAL  
BLACK TO TERMINAL 2.  
BLK  
YEL  
BLK  
WHT  
1
1. L1 SUPPLY VOLTAGE  
2. NC CONTACT  
3. NC CONTACT  
4. L2 SUPPLY VOLTAGE  
5. LINE - BEATER MOTOR CURRENT  
6. LOAD - BEATER MOTOR CURRENT  
YEL BLK  
RED  
WHT  
WHT  
L1  
1
FUSE 1A  
GRN/YEL  
MIX LOW TRANSFORMER  
BLK  
BLK  
PRP  
WHT/RED  
WHT/RED  
5
2
WHT/RED  
MIX LOW PCB A.  
W/CHIME/SNOOZE  
4
4
2) FOR "CCW" ROTATION OF GE/RBC  
BEATER MOTOR CONNECT  
INTERNAL BLUE TO TERMINAL 5 &  
INTERNAL YELLOW TO TERMINAL 2.  
T8  
VISCOSITY CONTROL TERMINALS  
RED  
(INTERNAL)  
BLK  
(INTERNAL)  
FIG. 5  
2
T5  
BRN  
4
RED  
BRN  
2
BRN  
L2  
LEESON BEATER MOTOR  
"CCW" ROTATION  
SILENCE PUSH  
BUTTON SWITCH  
BLK  
BLK  
GE/RBC  
A. O. SMITH  
.5 HP BEATER MOTOR  
(SEE NOTE #1)  
BEATER MOTOR  
"CCW" ROTATION  
(SEE NOTE #2)  
YEL BLK  
RED  
RED  
YEL  
FIG. 6  
BLK  
BLK  
YEL  
FUSE 1A  
MIX LOW TRANSFORMER  
START  
RELAY  
(047702-27)  
LEFT MIX  
OUT SWITCH  
LEFT MIX  
OUT LIGHT  
BLK  
BLK  
LINE  
MIX LOW PCB A.  
W/CHIME  
BLK  
BLK  
BLK  
BLK  
WHT  
INTERNAL  
YEL  
L1  
C
11  
START  
CAPACITOR  
(047703)  
GRN  
RED  
10  
LEFT MIX  
LOW SWITCH  
LEFT MIX  
LOW LIGHT  
OVERLOAD  
BRN  
5
2
S
BLK  
RED  
YEL  
13  
12  
BLK  
14  
RELAY  
4
BLK  
BLK  
BLK  
RED  
RIGHT MIX  
OUT SWITCH  
RIGHT MIX  
OUT LIGHT  
RUN  
CAPACITOR  
1
LEFT MIX  
LOW SWITCH  
LEFT MIX  
LOW LIGHT  
L2  
BLK  
YEL  
R
BLU  
BLK  
BLK  
RED  
162/168  
050205-40s  
11/12/13  
RIGHT MIX  
LOW SWITCH  
RIGHT MIX  
LOW LIGHT  
WINDING  
PROTECTOR  
(INTERNAL)  
START  
WINDING  
MAIN  
WINDING  
START  
CAPACITOR  
RIGHT MIX  
LOW SWITCH  
RIGHT MIX  
LOW LIGHT  
BLEED RESISTOR  
MODELS WITH MIX OUT LIGHT,  
MIX LOW LIGHT, W/AUDIBLE MIX  
OUT CHIME AND PUSH BUTTON SILENCE  
COMPRESSOR WIRING  
(MODEL TL3G W/HST)  
TECUMSEH COMPRESSOR WIRING  
MODELS WITH CHIME OPTION  
FIG. 3  
FIG. 1  
FIG. 2  
FIG. 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technicolor Thomson Camcorder CAMERA TTV 1707 User Manual
Technics Speaker SB AS500 User Manual
Technika Car Stereo System MP 112 User Manual
TechniSat DVD Player TechniBox VIACAM User Manual
Tektronix Network Card Spectrum Analyzer User Manual
Toshiba Computer Drive MK4026GAX HDD2193 User Manual
Toshiba Digital Camera CS3950DIF User Manual
Vulcan Hart Fryer GRD35F ML 126732 User Manual
Waves Network Card Trans X User Manual
Wayne Water Pump SYLT30 User Manual