OPERATOR’S
MANUAL
Model 432
Shake/Slush Freezer
Original Operating Instructions
053081-M
10/98 (Original Publication)
(Updated 8/14/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 1
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
2
2
3
4
Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beater Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 2
To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 3
Section 4
5
7
7
8
Model 432 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beater Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 5
Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Control Switch (Item 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Push- Button Switch (Item 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Display Light Switch (Item 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Indicator Light - “Mix Out” (Item 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Indicator Light - “Add Mix” (Item 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Viscosity Adjustment (Item 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Section 6
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Draining Product From The Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table of Contents
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents - Page 2
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Section 7
Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
During Cleaning and Sanitizing: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting Bacterial Count: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Regular Maintenance Checks: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Section 8
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Section 9
Section 10
Section 11
Section 12
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
E 1998 Carrier Commercial Refrigeration, Inc. (Original Publication)
(Updated August, 2014)
053081- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work
may be a violation of Copyright Law of the United States of America and other countries, could result in the
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further
civil and criminal penalties.
All rights reserved.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
To the Installer
The following information has been included in the
manual as safety and regulatory guidelines. For
complete installation instructions, please see the
Installation Checklist.
This unit has many sharp edges that can
cause severe injuries.
Site Preparation
Installer Safety
Review the area where the unit will be installed before
uncrating the unit. Make sure that all possible hazards
to the user and the equipment have been addressed.
In all areas of the world, equipment should be
installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of
70_-75_F (21_-24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.
This unit must NOT be installed in an area
where a water jet or hose can be used. NEVER use a
water jet or hose to rinse or clean the unit. Failure to
follow this instruction may result in electrocution.
S
Only authorized Taylor service personnel
should perform installation and repairs on
the equipment.
S
Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.
This unit must be installed on a level surface
to avoid the hazard of tipping. Extreme care should be
taken in moving this equipment for any reason. Two or
more persons are required to safely move this unit.
Failure to comply may result in personal injury or
equipment damage.
S
S
Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.
Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.
Uncrate the unit and inspect it for damage. Report any
damage to your Taylor Distributor.
This piece of equipment is made in the USA and has
USA sizes of hardware. All metric conversions are
approximate and vary in size.
The main power supply(s) to the freezer must
be disconnected prior to performing any repairs.
Failure to follow this instruction may result in personal
injury or death from electrical shock or hazardous
moving parts as well as poor performance or damage
to the equipment.
Air Cooled Units
DO NOT obstruct air intake and discharge openings:
A minimum of 6” (152 mm) on both sides and 0” on the
back is required. Failure to follow this instruction may
cause poor freezer performance and damage to the
machine.
Note: All repairs must be performed by an
authorized Taylor Service Technician.
131202
1
To the Installer
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
This unit must be plugged into a properly grounded
receptacle. The cord and plug must be sized for 20
Amp usage. The voltage specifications are
208- 230/60/1. Follow specifications listed on your
data plate.
S
S
Stationary appliances which are not
equipped with a power cord and a plug or
another device to disconnect the appliance
from the power source must have an all-pole
disconnecting device with a contact gap of
at least 3 mm installed in the external
installation.
Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer-sheathed cord (Code designation
60245 IEC 57) installed with the proper cord
anchorage to relieve conductors from strain,
including twisting, at the terminals and
protect the insulation of the conductors from
abrasion.
FOLLOW YOUR LOCAL ELECTRICAL CODES!
In the United States, this equipment is intended to be
installed in accordance with the National Electrical
Code (NEC), ANSI/NFPA 70- 1987. The purpose of
the NEC code is the practical safeguarding of persons
and property from hazards arising from the use of
electricity. This code contains provisions considered
necessary for safety. Compliance therewith and
proper maintenance will result in an installation
essentially free from hazard!
S
In all other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.
Each unit requires one power supply for each data
label on the unit. Check the data label(s) on the freezer
for branch circuit overcurrent protection or fuse, circuit
ampacity, and other electrical specifications. Refer to
the wiring diagram provided inside of the electrical box
for proper power connections.
If the supply cord is damaged, it must be
replaced by an authorized Taylor service
technician in order to avoid a hazard.
Beater Rotation
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
Beater rotation must be clockwise as viewed
looking into the freezing cylinder.
Note: The following procedures must be
performed by an authorized Taylor service
technician.
This unit is provided with an equipotential
grounding lug that is to be properly attached to the rear
of the frame by the authorized installer. The installation
location is marked by the equipotential bonding
symbol (5021 of IEC 60417-1) on both the removable
panel and the equipments frame.
To correct rotation on a single- phase unit, change the
leads inside the beater motor. (Follow the diagram
printed on motor.)
131202
To the Installer
Model 432
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Refrigerant
In consideration of our environment, Taylor
Taylor reminds technicians to be aware of and
in compliance with local government laws regarding
refrigerant recovery, recycling, and reclaiming
systems. For information regarding applicable local
laws, please contact your local authorized Taylor
distributor.
uses only HFC refrigerants. The HFC refrigerant used
in this unit is R404A. This refrigerant is generally
considered non-toxic and non-flammable, with an
Ozone Depleting Potential (ODP) of zero (0).
However, any gas under pressure is potentially
hazardous and must be handled with caution.
NEVER fill any refrigerant cylinder completely with
liquid. Filling the cylinder to approximately 80% will
allow for normal expansion.
WARNING: R404A refrigerants used in
conjunction with polyolester oils are extremely
moisture absorbent. When opening a refrigeration
system, the maximum time the system is open must
not exceed 15 minutes. Cap all open tubing to prevent
humid air or water from being absorbed by the oil.
Use only R404A refrigerant that conforms to
the AHRI standard 700 specification. The use of any
other refrigerant may expose users and operators to
unexpected safety hazards.
Refrigerant liquid sprayed onto the skin may
cause serious damage to tissue. Keep eyes and skin
protected. If refrigerant burns should occur, flush
immediately with cold water. If burns are severe, apply
ice packs and contact a physician immediately.
131202
3
To the Installer
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
To the Operator
The freezer you have purchased has been carefully
engineered and manufactured to give you dependable
operation. The Taylor Model 432, when properly
operated and cared for, will produce a consistent
quality product. Like all mechanical products, they will
require cleaning and maintenance. A minimum
amount of care and attention is necessary if the
operating procedures outlined in this manual are
followed closely.
municipal waste. The user is responsible for returning
the product to the appropriate collection facility, as
specified by your local code.
For additional information regarding applicable local
laws, please contact the municipal facility and/or local
distributor.
Compressor Warranty Disclaimer
The refrigeration compressor(s) on this unit are
warranted for the term stated in the Limited Warranty
section in this manual. However, due to the Montreal
Protocol and the U.S. Clean Air Act Amendments of
1990, many new refrigerants are being tested and
developed, thus seeking their way into the service
industry. Some of these new refrigerants are being
advertised as drop- in replacements for numerous
applications. It should be noted that in the event of
ordinary service to this unit’s refrigeration system,
only the refrigerant specified on the affixed data
label should be used. The unauthorized use of
alternate refrigerants will void your Taylor compressor
warranty. It is the unit owner’s responsibility to make
this fact known to any technician he employs.
This Operator’s Manual should be read before
operating or performing any maintenance on your
equipment.
Your Taylor freezer will NOT eventually compensate
for and correct any errors during the set- up or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that personnel responsible for the
equipment’s operation, both assembly and
disassembly, sit down together and go through these
procedures in order to be properly trained and to make
sure that no misunderstandings exist.
In the event you should require technical assistance,
please contact your local authorized Taylor Distributor.
It should also be noted that Taylor does not warrant
the refrigerant used in its equipment. For example, if
the refrigerant is lost during the course of ordinary
service to this unit, Taylor has no obligation to either
supply or provide replacement refrigerant either at
billable or unbillable terms. Taylor will recommend a
suitable replacement if the original refrigerant is
banned, obsoleted, or no longer available during the
five (5) year Taylor warranty of the compressor.
Your Taylor warranty is valid only if the parts are
authorized Taylor parts, purchased from the local
authorized Taylor Distributor, and only if all required
service work is provided by an authorized Taylor
service technician. Taylor reserves the right to deny
warranty claims on units or parts if non- Taylor
approved parts or incorrect refrigerant were installed
in the unit, system modifications were performed
beyond factory recommendations, or it is determined
that the failure was caused by abuse, misuse, neglect,
or failure to follow all operating instructions. For full
details of your Taylor Warranty, please see the Limited
Warranty section in this manual.
From time- to- time Taylor may test new refrigerant
alternates. Should a new refrigerant alternate prove,
through Taylor’s testing, that it would be accepted as
a drop- in replacement for this unit, then the disclaimer
in this “Compressor Warranty Disclaimer” section will
not apply to the use of the alternate refrigerant
approved by Taylor.
Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.
To find out the current status of an alternate refrigerant
as it relates to your compressor warranty, call Taylor or
your local authorized Taylor distributor. Be prepared to
provide the Model/Serial Number of the unit in
question.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other similar
legislation in effect after August 13, 2005. Therefore,
it must be collected separately after its use is
completed, and cannot be disposed as unsorted
Note: Continuing research results in steady
improvements; therefore, information in this
Operator Manual is subject to change without
notice.
131202
To the Operator
Model 432
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
Safety
We, at Taylor Company, are concerned about the
safety of the operator at all times when they are
coming in contact with the unit and its parts. Taylor
makes every effort to design and manufacture
built- in safety features to protect both operators and
service technicians.
S
S
All repairs should be performed by an
authorized Taylor service technician.
The main power supplies to the unit must be
disconnected prior to performing installation,
repairs, or maintenance.
Installing and servicing refrigeration equipment can
be hazardous due to system pressure and electrical
components. Only trained and qualified service
personnel should install, repair, or service
refrigeration equipment. When working on
refrigeration equipment, observe precautions noted
in the literature, tags and labels attached to the unit,
and other safety precautions that may apply. Follow
all safety code requirements. Wear safety glasses
and work gloves.
S
S
S
DO NOT operate the unit unless it is
properly grounded.
DO NOT operate the unit with larger fuses
than specified on the unit’s data label.
Units that are permanently connected to
fixed wiring and for which leakage currents
may exceed 10 mA, particularly when
disconnected or not used for long periods,
or during initial installation, shall have
protective devices such as a GFI, to protect
against the leakage of current, installed by
the authorized personnel to the local codes.
IMPORTANT - Failure to adhere to the
following safety precautions may result in
severe personal injury or death. Failure to
comply with these warnings may also damage
the unit and/or its components. Such damage
may result in component replacement and
service repair expenses.
S
S
Stationary units which are not equipped with
a power cord and a plug or another device
to disconnect the appliance from the power
source must have an all-pole disconnecting
device with a contact gap of at least 3 mm
installed in the external installation.
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer-sheathed cord (Code designation
60245 IEC 57) installed with the proper cord
anchorage to relieve conductors from strain,
including twisting, at the terminals and
protect the insulation of the conductors from
abrasion.
DO NOT operate the unit without reading
this entire Operator Manual first. Failure to follow all
of these operating instructions may result in damage
to the unit, poor performance, health hazards,
personal injury, or death.
This unit is to be used only by trained
personnel. It is not intended for use by children or
people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge.
Where limited equipment operation is allowed for
public use, such as a self- serve application,
supervision or instruction concerning the use of the
appliance by a person responsible for their safety is
required. Children should be supervised to ensure
that they do not play with the appliance.
If the supply cord is damaged, it must be
replaced by an authorized Taylor service
technician in order to avoid a hazard.
Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
Distributor for service.
131202
5
Safety
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
An equipotential grounding lug is provided with this
unit. Some countries require the grounding lug be
properly attached to the rear of the frame by the
authorized installer. The installation location is marked
by the equipotential bonding symbol (5021 of IEC
60417-1) on both the removable panel and the unit’s
frame.
Access to the service area of the unit must be
restricted to persons having knowledge and practical
experience with the unit, in particular as far as safety
and hygiene are concerned.
Cleaning and sanitizing schedules are
governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to the
cleaning section of this Operator Manual for the proper
procedure to clean this unit.
DO NOT use a water jet to clean or rinse the
unit. Failure to follow these instructions may result in
serious electrical shock.
S
S
DO NOT allow untrained personnel to
operate this machine.
DO NOT operate the freezer unless all
service panels and access doors are
restrained with screws.
This unit is designed to maintain product
temperature under 41_F (5_C). Any product being
added to this unit must be below 41_F (5_C). Failure
to follow this instruction may result in health hazards
and poor freezer performance.
S
DO NOT remove any internal operating
parts (examples: freezer door, beater,
scraper blades, etc.) unless all control
switches are in the OFF position.
DO NOT obstruct air intake and discharge openings:
Failure to follow these instructions may result in severe
personal injury to fingers or hands from hazardous
moving parts.
A minimum of 6” (152 mm) on both sides and 0” on the
back is required. Failure to follow this instruction may
cause poor freezer performance and damage to the
machine.
This unit has many sharp edges that can
cause severe injuries.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of 70_ -
75_F (21_ - 24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
S
DO NOT put objects or fingers in the door
spout. This may contaminate the product
and cause severe personal injury from blade
contact.
S
USE EXTREME CAUTION when removing
the beater asssembly. The scraper blades
are very sharp.
DO NOT run the unit without product. Failure to follow
this instruction can result in damage to the unit.
This unit must be placed on a level surface.
NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of 1.0
meter from the surface of the machine and at a height
of 1.6 meters from the floor.
Extreme care should be taken when moving the unit
for any reason. Two or more persons are required to
safely move this unit. Failure to comply may result in
personal injury or damage to the unit.
131202
Safety
Model 432
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Operator Parts Identification
Model 432
Figure 1
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
STUD-NOSE CONE
PANEL-FRONT-UPPER
PART NO.
1
2
3
4
5
6
7
8
COVER A.-HOPPER
PANEL-REAR
X52452
052363
052527
052361
052377
X46848
046851
027504
9
013496
052360
052617
045445
052243
052359
052362
052065
10
PANEL-SIDE-RIGHT-LOUVERED
PANEL-FRONT-LOWER
GASKET-BASE PAN
TRAY A.-DRIP
*10a GASKET-INSULATOR
11
12
13
14
15
BULB-LIGHT-FLORESCENT
BRACKET-LIGHT
LENS-DECORATIVE PLATE
PANEL-SIDE-LEFT
SHIELD-SPLASH
PAN-DRIP 17-1/4” LONG
SHELF-DRIP TRAY
*NOT SHOWN
7
Operator Parts Identification
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Beater Door Assembly
Figure 2
120730
Operator Parts Identification
Model 432
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Beater Door Assembly Parts Identification
ITEM
DESCRIPTION
DOOR A. - PARTIAL
PART NO.
ITEM
DESCRIPTION
BEARING - GUIDE
PART NO.
1
2
3
4
5
6
X39248
X47384
029880
047735
032504
047734
11
12
13
14
014496
046238
046237
014030
HANDLE A. DRAW
NUT-STUD
CLIP - SCRAPER BLADE
BLADE - SCRAPER PLASTIC
BUSTER - ICE
GASKET - DOOR 5.109" ID X
5.630
O-RING - 1" OD X .139 W
15
16
17
18
19
BEARING - FRONT
013116
X49490
035418
032560
025307
VALVE DRAW - SLUSH - ICE
BUSTER
BEATER A. - 4 QT. 1 PIN
SHAFT - BEATER
7
8
VALVE A. - HANDLE PIN
O-RING - .291 OD X .080 W
ARM - TORQUE
X25929
018550
052450
X50382
SEAL - DRIVE SHAFT
O-RING 7/8 OD X .139 W
9
10
TORQUE ASSEMBLY
120730
9
Operator Parts Identification
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Figure 3
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
2
3
4
5
KIT A.- TUNE UP
X39969
023316
013163
013072
013071
6
7
BRUSH- DRAW VALVE 1- 1/2X3
LUBRICANT- TAYLOR
014753
047518
041082
X52521
BRUSH- MIX PUMP 3” X 7”
PAIL- 10 QT.
8
SANITIZER- KAY- 5 (125 PKTS)
PANEL A.- AIR GUIDE
BRUSH- DOUBLE ENDED
BRUSH- REAR BEARING 1 X 2
*9
*PRIOR TO S/N J8070000.
(NOTE: OPTIONAL FIELD KIT X52633 J8070000/UP)
140814
Operator Parts Identification
Model 432
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
Important: To the Operator
Figure 4
Control Switch (Item 1)
Item
Description
The center position is “OFF”. The left position is
“WASH”, which activates only the beater motor. The
right position is “AUTO”, which activates the beater
1
2
3
4
5
6
Switch- Toggle - 3 PDT
Switch- Push Button - SPST
motor and the refrigeration system.
Switch- Toggle- SPST - 3/4 HP/250 V
Light- Amber- Rect. - 12 VDC - MIX OUT
Light- Amber- Rect. - 12 VDC - ADD MIX
Viscosity Adjustment
Push- Button Switch (Item 2)
If an overload condition occurs, the freezer will
automatically stop operating. To properly reset the
freezer, place the toggle switch in the “OFF” position.
Wait two or three minutes; then press the push- button
switch. Place the power switch in the “WASH” position
and observe the freezer’s performance. Place the
power switch in the “AUTO” position.
The following chart identifies the symbol definitions
used on the operator switches.
Note: If the freezer is unplugged from the wall
receptacle, it will be necessary to press the
push- button switch for the freezer to operate once
power is re- established.
= The “ON/AUTO” button.
= The “OFF” button.
Display Light Switch (Item 3)
The display light switch is located under the control
channel. The left position is “OFF”. The right position
is “ON”, and activates the display light.
= The “WASH” button.
11
Important: To the Operator
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicator Light - “Mix Out” (Item 4)
Viscosity Adjustment (Item 6)
A mix out indicating light is located on the front of the
machine. When the light is flashing, it indicates that the
hopper is empty and the mix supply needs
replenishing. To prevent damage to the unit,
refrigeration discontinues automatically when the mix
out indicator lights illuminates. Refrigeration willrestart
30 seconds after the mix supply is replenished.
The viscosity (thickness) of the slush can be adjusted
by turning the viscosity adjustment screw located
under the control channel. Turn the viscosity
adjustment screw clockwise for a thicker product, or
counterclockwise for a thinner product. After making
an adjustment, allow the refrigeration system to cycle
2 or 3 times to accurately evaluate the viscosity.
Indicator Light - “Add Mix” (Item 5)
A mix level indicating light is located on the front of the
machine. When the light is flashing, it indicates that the
mix hopper has a low supply of product and should be
refilled as soon as possible.
Important: To the Operator
Model 432
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6
Operating Procedures
The Model 432 freezer is designed to produce shake
or slush product at the desired thickness. This unit has
a 4 quart freezing cylinder.
Note: Do not install the boot seal inside out.
Install the drive shaft. Insert the beater drive shaft into
the rear shell bearing and engage the square end
firmly into the female socket of the drive unit. Be
certain that the drive shaft fits into the drive coupling
without binding.
We begin our instructions at the point where we enter
the store in the morning and find the parts
disassembled and laid out to air dry from the previous
night’s brush cleaning. These opening procedures will
show you how to assemble these parts into thefreezer,
sanitize them, and prime the freezer with fresh mix in
preparation to serve your first portion. If you are
disassembling the machine for the first time or need
information to get to this point in our instructions, turn
to page 19, “Disassembly”, and start there.
Assembly
Note: When lubricating parts, use an approved food
grade lubricant (example: Taylor Lube).
MAKE SURE THE POWER SWITCH IS IN
THE “OFF” POSITION! Failure to follow this
instruction may result in severe personal injury from
hazardous moving parts.
Figure 6
Step 1
Step 2
Lubricate the groove on the drive shaft and slide the
o- ring in place. Lubricate the o- ring and shaft portion
that comes in contact with the bearing. DO NOT
lubricate the square end of the drive shaft. Lubricate
the boot seal groove and slide the boot seal over the
shaft and groove until it snaps into place. Fill the inside
portion of the seal with 1/4” more lubricant and evenly
lubricate the end of the seal that fits onto the rear shell
bearing.
Install the beater assembly. First check the scraper
blade for any nicks or signs of wear. If any nicks are
present, replace the blade. If the blade is in good
condition, place the clip over the blade and install the
blade and clip on the beater assembly. Be sure the
holes in the blade and the clip are securely positioned
over the beater pin.
Figure 5
Figure 7
13
Operating Procedures
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Holding the beater securely, slide the beater into the
freezing cylinder and align the hole at the rear of the
beater with the flats on the end of the drive shaft.
Slide the beater the remainder of the way into the
freezing cylinder and over the end of the drive shaft.
The beater assembly will not protrude beyond the front
of the freezing cylinder.
Figure 10
Step 5
Assemble the freezer door with the “Ice Buster” (door
spout clearing device). To assemble the door with the
ice buster, install the o- rings on the draw valve and
lubricate.
Figure 8
Step 3
Install the white plastic guide bearing on the short end
of the torque rotor. Slide the o- ring into the groove on
the long end of the torque rotor and lubricate the
o- ring. Do not lubricate the guide bearing.
Figure 11
Insert the draw valve into the door, leaving
approximately half of the valve sticking out the top of
the door.
Figure 9
Step 4
Insert the torque rotor end with the guide bearing into
the pilot hole in the center of the drive shaft. The hole
in the torque rotor shaft should be rotated to the 12
o’clock position.
Figure 12
Operating Procedures
Model 432
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotate the draw valve so the flats on the top of thedraw
valve are perpendicular to the door face.
Place the large rubber gasket into the groove on the
back side of the freezer door. Slide the white, plastic
front bearing onto the bearing hub, making certain that
the flanged end of the bearing is resting against the
freezer door. DO NOT lubricate the door gasket or
front bearing.
Figure 13
Insert the ice buster through the door spout and into
the slot located just above the lower o- ring.
Figure 16
Step 6
Install the door on the four studs on the front of the
freezing cylinder. Install the four handscrews on the
door, and tighten them equally in a criss- cross
manner.
Figure 14
With the ice buster in place, rotate the draw valve to
allow installation of the draw handle. This will lock the
ice buster in place. Install the draw handle pin, and
close the draw valve by moving the handle to the left.
Figure 15
Figure 17
15
Operating Procedures
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7
Step 9
Position the torque arm by inserting it through the slot
in the torque switch arm and down into the hole in the
torque rotor which protrudes from the door. Verify
proper installation by moving the torque rotor back and
forth to be sure it moves freely and easily.
Install the front drip tray and splash shield beneath the
door spouts.
Figure 20
Step 10
Figure 18
Lay the air/mix feed tube (optional) in the bottom of the
mix hopper.
Step 8
Install the front drip pans. Slide the long drip pans into
the holes in the front panel.
Figure 21
Figure 19
Repeat these steps for the other side of the unit.
Operating Procedures
Model 432
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5
Sanitizing
Place an empty pail beneath the door spout and move
the draw handle to the right. Draw off all the sanitizing
solution. When the sanitizer stops flowing from the
door spout, move the draw handle to the left and place
the control switch in the “OFF” position.
Step 1
Prepare an approved 100 PPM sanitizing solution
(examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2
gal. [7.6 liters] of Stera- SheenR). USE WARM
WATER AND FOLLOW THE MANUFACTURER’S
SPECIFICATIONS.
Step 2
Pour the sanitizing solution into the hopper and allow
it to flow into the freezing cylinder.
Figure 24
Figure 22
Step 6
Step 3
Stand the air/mix feed tube (optional) in the corner of
the hopper.
While the solution is flowing into the freezing cylinder,
brush clean the mix hopper, air/mix feed tube
(optional) and mix inlet hole.
Step 4
Place the power switch in the “WASH” position. This
will agitate the sanitizing solution in the freezing
cylinder. Allow the solution to agitate for five minutes.
Figure 25
Figure 23
Repeat these steps for the other side of the unit.
140814
17
Operating Procedures
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: To identify the viscosity adjustment screw, see
illustration on page 11.
Priming
Step 1
Step 4
With a pail beneath the door spout, move the draw
handle to the right. Pour two gallons (7.6 liters) of
FRESH mix into the hopper and allow it to flow into the
freezing cylinder. This will force out any remaining
sanitizing solution. When full strength mix is flowing
from the door spout, move the draw handle to the left.
Place the mix hopper cover in position. Periodically,
during the day’s operation, check to be sure there is a
sufficient amount of mix in the hopper.
Step 2
When the mix has stopped bubbling down into the
freezing cylinder, install the air/mix feed tube (optional)
in the mix inlet hole with the hole side down.
Figure 28
Repeat these steps for the other side of the unit.
Figure 26
Step 3
Closing Procedure
Place the power switch in the “AUTO” position. When
the unit cycles off, the product will be at serving
viscosity. The viscosity (thickness) of the slush can be
adjusted by turning the viscosity adjustment screw
located under the control channel. Turn the viscosity
adjustment screw clockwise for a thicker product, or
counterclockwise for a thinner product. After making
an adjustment, allow the refrigeration system to cycle
2 or 3 times to accurately evaluate the viscosity.
To disassemble this unit, the following items will be
needed:
S
S
S
S
Two cleaning pails
Necessary brushes (provided with freezer)
Cleaner
Single service towels
Draining Product From The
Freezing Cylinder
Step 1
Place the power switch in the “OFF” position as far
ahead of cleaning time as possible to allow frozen
product to soften for easier cleaning.
Step 2
Raise the hopper cover. If the unit is equipped with an
air/mix feed tube, take it to the sink for cleaning.
Figure 27
Operating Procedures
Model 432
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
Cleaning
If local health codes permit the use of rerun, place
a sanitized, NSF approved stainless steel rerun
container beneath the door spout. Place the power
switch in the “WASH” position and move the draw
handle to the right. When all the product stops flowing
from the door spout, move the draw handle to the left
and place the power switch in the “OFF” position.
Place the sanitized lid on the rerun container and place
it in the walk- in cooler.
Step 1
Prepare an approved 100 PPM cleaning solution
(examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2
gal. [7.6 liters] of Stera- SheenR). USE WARM
WATER AND FOLLOW THE MANUFACTURER’S
SPECIFICATIONS.
Step 2
Pour the cleaning solution into the hopper and allow it
to flow into the freezing cylinder.
Note: If local health codes DO NOT permit the use
of rerun, the product must be discarded. Follow the
instructions in the previous step, except drain the
product into a pail and properly discard the mix.
Step 3
While the solution is flowing into the freezing cylinder,
brush- clean the mix hopper and mix inlet hole.
ALWAYS FOLLOW LOCAL HEALTH CODES.
Step 4
Place the power switch in the “WASH” position. This
will agitate the cleaning solution in the freezing
cylinder.
Repeat these steps for the other side of the unit.
Step 5
Rinsing
Place an empty pail beneath the door spout and move
the draw handle to the right. Draw off all the cleaning
solution. When the solution stops flowing from the door
spout, move the draw handle to the left, and place the
power switch in the “OFF” position.
Step 1
Pour two gallons (7.6 liters) of cool, cleanwater intothe
mix hopper. With the brushes provided, scrub the mix
hopper and the mix inlet hole.
Repeat these steps for the other side of the unit.
Disassembly
Step 1
BE SURE THE CONTROL SWITCH IS IN THE
“OFF” POSITION.
Step 2
Remove the handscrews, freezer door, beater
assembly, torque rotor, scraper blade and drive shaft
from the freezing cylinder. Take these parts to the sink
for cleaning.
Figure 29
Step 2
Step 3
With a pail beneath the door spout, place the power
switch in the “WASH” position and move the draw
handle to the right. Drain all the rinse water from the
freezing cylinder. When the rinse water stops flowing
from the door spout, move the draw handle to the left
and place the control switch in the “OFF” position.
Remove the front drip tray and the splash shield. Take
these parts to the sink for cleaning.
Step 4
Remove the rear drip pans from the front panel. Note:
If the drip pans are filled with an excessive amount of
mix, it is an indication the drive shaft seals should be
replaced or properly lubricated.
Repeat this procedure until the rinse water being
drawn from the freezing cylinder is clear.
Repeat these steps for the other side of the unit.
Repeat these steps for the other side of the unit.
140814
19
Operating Procedures
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4
Brush Cleaning
Thoroughly brush- clean all disassembled parts in the
cleaning solution, making sure all lubricant and mix film
is removed. Place all the cleaned parts on a clean, dry
surface to air dry.
Step 1
Prepare a sink with a cleaning solution (examples:
Kay- 5R or Stera- SheenR). USE WARM WATER
AND FOLLOW THE MANUFACTURER’S SPECIFIC-
ATIONS. (If another approved cleaner is used, dilute
according to label instructions. IMPORTANT: Follow
the label directions. Too STRONG of a solution can
cause parts damage, while too MILD of a solution will
not provide adequate cleaning.) Make sure all brushes
provided with the freezer are available for brush
cleaning.
Step 5
Return to the freezer with a small amount of cleaning
solution. Brush- clean the rear shell bearing at the
back of the freezing cylinder with the black bristle
brush.
Step 2
Remove the o- ring and seal from the drive shaft.
Remove the o- ring and the bearing from the torque
rotor.
Step 3
Remove the draw valve, ice buster, front bearing, and
gasket from the freezer door. Remove all o- rings.
Figure 30
Note: To remove the o- ring, use a single service
towel to grasp the o- ring. Apply pressure in an upward
direction until the o- ring pops out of its groove. With
the other hand, push the top of the o- ring forward until
it rolls out of the groove and can be removed easily.
Step 6
Wipe clean all exterior surfaces of the freezer.
Repeat these steps for the other side of the unit.
Operating Procedures
Model 432
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
Important: Operator Checklist
the rerun with fresh mix in a ratio of 50/50 during
the day’s operation.
During Cleaning and Sanitizing:
j 6. On a designated day of the week, run the mix as
low as feasible and discard after closing. This
will break the rerun cycle and reduce the
possibility of high bacteria and coliform counts.
ALWAYS FOLLOW LOCAL HEALTH CODES.
Cleaning and sanitizing schedules are governed
by federal, state, or local regulatory agencies, and
must be followed accordingly. If the unit has a
“Standby mode”, it must not be used in lieu of
proper cleaning and sanitizing procedures and
frequencies set forth by the ruling health
authority. The following check points should be
stressed during the cleaning and sanitizing
operations.
j 7. Properly prepare the cleaning and sanitizing
solutions. Read and follow label directions
carefully. Too strong of a solution may damage
the parts and too weak of a solution will not do
an adequate job of cleaning or sanitizing.
j 8. Temperature of mix in mix hopper and walk- in
cooler should be below 40_F. (4.4_C.).
Regular Maintenance Checks:
j 1. Replace scraper blades that are nicked,
damaged or worn down. Before installing
beater, be certain the scraper blade is properly
attached.
CLEANING AND SANITIZING MUST BE
PERFORMED DAILY.
Troubleshooting Bacterial Count:
j 1. Thoroughly clean and sanitize machine
regularly, including complete disassembly and
brush cleaning.
j 2. Check rear shell bearing for signs of wear
(excessive mix leakage in drip pan) and be
certain it is properly cleaned.
j 3. Using a screwdriver and cloth towel, keep the
rear shell bearing and the female square drive
socket clean and free of lubricant and mix
deposits.
j 2. Use all brushes supplied for thorough cleaning.
The brushes are specially designed to reach all
mix passageways.
j 3. Use the white bristle brush to clean the mix feed
tube, which extends from the hopper down to
the rear of the freezing cylinder.
j 4. Dispose of o- rings and seals if they are worn,
torn, or fit too loosely, and replace with new.
j 5. Follow all lubricating procedures as outlined in
j 4. Use the black bristle brush to thoroughly clean
the rear shell bearing located at the rear of the
freezing cylinder. Be sure to have a generous
amount of cleaning solution on the brush.
“Assembly”.
j 6. Check the condenser(s) for accumulation of dirt
and lint. Dirty condensers will reduce the
efficiency and capacity of the machine.
Condensers should be cleaned monthly with a
soft brush. Never use screwdrivers or other
metal probes to clean between the fins.
j 5. IF LOCAL HEALTH CODES PERMIT THE
USE OF RERUN, make sure the mix rerun is
stored in a sanitized, covered stainless steel
container and used the following day. DO NOT
prime the machine with rerun. When using
rerun, skim off the foam and discard, then mix
Note: For machines equipped with an air filter,
it will be necessary to vacuum clean the filters
on a monthly schedule.
080118
21
Important: Operator Checklist
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Winter Storage
If the place of business is to be closed during the winter
months, it is important to protect the freezer by
following certain precautions, particularly if the
building is to be left unheated and subject to freezing
conditions.
Wrap detachable parts of the freezer such as beater,
blades, drive shaft, and freezer door, and place in a
protected dry place. Rubber trim parts and gaskets
can be protected by wrapping with moisture- proof
paper. All parts should be thoroughly cleaned of dried
mix or lubrication accumulations which attract mice
and other vermin.
Disconnect the freezer from the main power source to
prevent possible electrical damage. Your local Taylor
Distributor can perform this service for you.
Important: Operator Checklist
Model 432
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8
Troubleshooting Guide
PROBLEM
PROBABLE CAUSE
REMEDY
PAGE
REF.
18
1. No product being
dispensed.
a. Control switch is in the
“OFF” position.
a. Place control switch in the
“AUTO” position.
- - -
b. Improper mixing of
product.
b. Carefully follow directions
for mixing product.
18
11
c. Inadequate mix in hopper.
c. Fill hopper with mix.
d. Product frozen-up in
freezing cylinder.
d. Adjust viscosity
adjustment accordingly.
11
e. Unit out on reset.
e. Place control switch in the
“OFF” position. Press the
push-button switch.
Return control switch to
“AUTO”.
1
f. Beater assembly is
rotating counterclockwise.
Control switch is not in
“AUTO”.
f. If the beater is rotating
counterclockwise, call a
service technician to
correct the rotation.
- - -
- - -
- - -
- - -
11
g. Unit unplugged at wall
receptacle.
g. Plug in power cord.
h. Tripped circuit breaker or
blown fuse.
h. Reset circuit breaker or
replace fuse.
2. Unit will not operate in the
“AUTO” or “WASH” mode.
a. Unit unplugged at wall
receptacle.
a. Plug in power cord.
b. Tripped circuit breaker or
blown fuse.
b. Reset circuit breaker or
replace fuse.
c. Unit out on reset.
c. Place the control switch in
the “OFF” position. Press
the push-button switch.
Return control switch to
“AUTO”.
11
21
3. No compressor operation
in the “AUTO” mode.
a. Beater motor is out on
overload.
a. Place control switch in
“OFF” position. Press the
push-button switch.
Return control switch to
“AUTO”.
b. Condenser dirty A/C.
b. Clean condenser monthly.
23
Troubleshooting Guide
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSE
REMEDY
PAGE
REF.
18
4. Product too thick.
a. Inadequate mix in hopper.
a. Fill hopper with mix.
- - -
b. Improper mixing of
product.
b. Carefully follow directions
for mixing product.
11
16
13
c. The viscosity adjustment
is set incorrectly.
c. Adjust the viscosity
control.
d. The torque arm is not
installed.
d. Install the torque arm.
5. Product too thin.
a. Missing, incorrectly
installed, or bad scraper
blade.
a. Install or replace scraper
blade.
- - -
11
b. Improper mixing of
product.
b. Carefully follow directions
for mixing product.
c. The viscosity adjustment
is set incorrectly.
c. Adjust accordingly.
- - -
d. Incorrect beater rotation.
(Rotation must be
clockwise.)
d. Contact service
technician.
21
e. Dirty condensers.
e. Clean regularly.
- - -
6. Scored walls of freezing
cylinder.
a. Broken pin on beater
assembly.
a. Repair or replace beater
assembly.
14
13
b. Front bearing worn or
missing.
b. Replace or install front
bearing.
7. Excessive leakage into
rear drip pan.
a. Improper or inadequate
lubrication of drive shaft
seal.
a. Use correct lubricant
(Taylor Lube) and follow
lubrication procedures.
25
- - -
13
b. Bad or missing seal on
drive shaft.
b. Replace seal every 3
months.
c. Worn rear shell bearing.
c. Contact service technician
for replacement.
8. Excessive leakage from
door spout.
a. Improper or inadequate
lubrication of draw valve
o-rings.
a. Use correct lubricant
(Taylor Lube) and follow
lubrication procedures.
25
13
b. Bad or missing o-rings on
draw valve.
b. Replace o-rings every 3
months.
9. Unable to remove drive
shaft.
a. Lubrication on square end
of drive shaft.
a. Do not lubricate square
end. Contact service
technician for
replacement.
- - -
b. Rounded corners of drive
shaft, drive coupling, or
both.
b. Contact service technician
to replace drive shaft,
drive coupling, or both.
Troubleshooting Guide
Model 432
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 9
Parts Replacement Schedule
PART DESCRIPTION
EVERY 3
MONTHS
EVERY 4
MONTHS
EVERY 6
MONTHS
ANNUALLY
QUANTITIES
TO BE
REPLACED
Drive Shaft Seal
X
X
2
2
2
2
2
2
2
4
1
Drive Shaft O-Ring
Scraper Blade
X
Freezer Door Gasket
Front Bearing
X
X
X
X
X
Guide Bearing
Torque Rotor O-Ring
Draw Valve O-Rings
Black Bristle Brush - 1” x 2”
Inspect &
Replace if
Necessary
Maximum
Maximum
Maximum
White Bristle Brush -
1-1/2” x 2”
Inspect &
Replace if
Necessary
1
1
White Bristle Brush - 3” x 7”
Inspect &
Replace if
Necessary
25
Parts Replacement Schedule
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 10 Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)
to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,
will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for
a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed
below and on the reverse (if any) of this document.
Product
Soft Serve
Part
Limited Warranty Period
Five (5) years
Insulated shell assembly
Frozen Yogurt
Shakes
Refrigeration compressor
(except service valve)
Five (5) years
Beater motors
Two (2) years
Two (2) years
Two (2) years
Smoothies
Frozen Beverage
Batch Desserts
Beater drive gear
Printed circuit boards and
Softech controls beginning
with serial number H8024200
Parts not otherwise listed in
this table or excluded below
One (1) year
LIMITED WARRANTY CONDITIONS
1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins
ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of
purchase may be required at time of service.
2. This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are
used.
3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.
5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective parts, replacement parts, or new Products.
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers.
131202
Limited Warranty on Equipment
Model 432
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.
4. External hoses, electrical power supplies, and machine grounding.
5. Parts not supplied or designated by Taylor, or damages resulting from their use.
6. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or
water supply specification of the Product; or components repaired or altered in any way so as, in the
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.
9. Any Product purchased over the Internet.
10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will
void this limited warranty.
13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or
remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
27
Limited Warranty on Equipment
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 11
Limited Warranty on Parts
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally
(the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service
agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions
listed below and on the reverse (if any) of this document.
Part’s Warranty Class Code or Part
Class 103 Parts¹
Limited Warranty Period
Three (3) months
Class 212 Parts²
Twelve (12) months
Twelve (12) months
No warranty
Class 512 Parts
Class 000 Parts
Taylor Part #072454 (Motor- 24VDC *C832/C842*)
Four (4) years
LIMITED WARRANTY CONDITIONS
1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required
at time of service.
2. This limited warranty is valid only if the Part is installed and all required service work in connection with the
Part is performed by an authorized Taylor distributor or service agency.
3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.
4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.
6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate
Taylor Limited Warranty on freezer or grill equipment.
7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this
limited warranty.
1, 2
Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.
131202
Limited Warranty on Parts
Model 432
28
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective Parts, replacement Parts, or new Parts.
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers or carbon and grease buildup.
3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including
the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper
assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but
not limited to the platen and plate, sides of the shroud or top of the shroud.
4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or
in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or
other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials
or cleaning processes not approved for use by Taylor.
5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any
release sheets and clips for the Product’s upper platen assembly.
6. External hoses, electrical power supplies, and machine grounding.
7. Parts not supplied or designated by Taylor, or damages resulting from their use.
8. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or
water supply specification of the unit in which a part is installed; or Parts or the units in which they are
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or
normal wear or deterioration.
11. Any Part purchased over the Internet.
12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is
installed will void this limited warranty.
15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
29
Limited Warranty on Parts
Model 432
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Limited Warranty on Parts
Model 432
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 12
Parts List
+ Available Separately
080619
Model 432
Parts List
31
Download from Www.Somanuals.com. All Manuals Search And Download.
+ Available Separately
Parts List
Model 432
32
Download from Www.Somanuals.com. All Manuals Search And Download.
+ Available Separately
140814
Model 432
Parts List
33
Download from Www.Somanuals.com. All Manuals Search And Download.
+ Available Separately
Parts List
Model 432
34
Download from Www.Somanuals.com. All Manuals Search And Download.
+ Available Separately
Model 432
Parts List
35
Download from Www.Somanuals.com. All Manuals Search And Download.
L1
L2
BLK
BLACK
WHITE/BLACK STRIPE
A
B
LEFT
POWER
SWITCH
LEFT PUSHBUTTON
SWITCH
5
6
3
4
BLK/WHT
OFF
WHT
AUTO
WASH
AUTO
WASH
AUTO
WASH
CORCOM
FILTER
BLK
BLU
COMPRESSOR
HIGH PRESSURE
SWITCH
LEFT BEATER
OVERLOAD
RELAY
OFF
OFF
ORANGE
RED/WHT
A
B
LEFT BEATER
RELAY COIL
WHT
A
B
LEFT COMPRESSOR
RELAY COIL
BLK/WHT
B T R
C O M P L 1
L 2
YELLOW
LEFT
PCB A.
SET SWITCH
TO 240V
BROWN
WHITE/BLACK
RED/WHT
BRN/WHT
WHT
WHT/RED
BLU/WHT
WHT/BLU
GRA/BLK
4
BLK
YEL
WHT
2
1
4
3
LEFT BEATER RELAY
LEFT
BEATER MOTOR
FIG.1
BLK
BLK
ORN/WHT
WHT
LEFT SUCTION SOLENOID
5
3
LEFT COMPRESSOR RELAY
LEFT LIQUID SOLENOID
PURPLE/WHITE
6
4
WHT
LEFT COMPRESSOR RELAY
A1
A2
COMPRESSOR CONTACTOR COIL
6
4
RIGHT COMPRESSOR RELAY
BLACK
BLK
WHITE/BLK STRIPE
A
B
RIGHT
POWER
SWITCH
RIGHT PUSHBUTTON
SWITCH
5
6
3
4
WHT
BRN/WHT
AUTO
WASH
AUTO
WASH
AUTO
WASH
CORCOM
FILTER
BLU
OFF
OFF
OFF
RIGHT BEATER
OVERLOAD
RELAY
ORN
A
B
RED/WHT
RIGHT BEATER
RELAY COIL
WHT
A
B
RIGHT COMPRESSOR
RELAY COIL
BLK/WHT
B T R
C O M P L 1
L 2
YEL
RIGHT
PCB A.
SET SWITCH
TO 240V
BRN
WHT/BLK
RED/WHT
BRN/WHT
WHT
WHT/RED
WHT/BLU
BLU/WHT
GRA/BLK
4
BLK
WHT
YEL
2
1
4
3
S T A R T
M A I N
RIGHT BEATER RELAY
RIGHT
BEATER MOTOR
FIG.1
BLK
WHT
WHT
ORN/WHT
RIGHT SUCTION SOLENOID
5
3
RIGHT COMPRESSOR RELAY
RIGHT LIQUID SOLENOID
WHT
BLK
BLK
COMP
FIG.2
L1
T1
T2
L2
COMPRESSOR
CONTACTOR
COMPRESSOR
CONTACTOR
BLK
BLK
FAN
MTR
BLK
BLK/WHT
WHT
BALLAST
432
052145-27
11/18/13
LIGHT SWITCH
RED
RED
L
BLUE
BLUE
Download from Www.Somanuals.com. All Manuals Search And Download.
L3
L1
L2
BLACK
BLACK
BLACK
WHITE/BLACK STRIPE
A
B
LEFT
POWER
SWITCH
LEFT PUSHBUTTON
SWITCH
5
6
3
4
BLK/WHT
OFF
WHITE
AUTO
WASH
AUTO
WASH
AUTO
WASH
CORCOM
FILTER
BLACK
BLUE
COMPRESSOR
HIGH PRESSURE
SWITCH
LEFT BEATER
OVERLOAD
RELAY
OFF
OFF
ORANGE
RED/WHT
A
B
LEFT BEATER
RELAY COIL
WHITE
A
B
LEFT COMPRESSOR
RELAY COIL
BLACK/WHITE
B T R
C O M P L 1
L 2
YELLOW
LEFT
PCB A.
SET SWITCH
TO 240V
BROWN
WHITE/BLACK
RED/WHITE
BROWN/WHITE
WHITE
WHITE/RED
BLUE/WHITE
WHITE/BLUE
GRAY/BLACK
4
BLACK
YELLOW
WHITE
2
1
4
3
LEFT BEATER RELAY
LEFT
BEATER MOTOR
(SEE FIG 1)
BLACK
BLACK
ORANGE/WHITE
WHITE
WHITE
5
3
LEFT SUCTION SOLENOID
LEFT COMPRESSOR RELAY
LEFT LIQUID SOLENOID
PURPLE/WHITE
6
4
LEFT COMPRESSOR RELAY
A1
A2
COMPRESSOR CONTACTOR COIL
6
4
RIGHT COMPRESSOR RELAY
BLACK
BLACK
WHITE/BLACK STRIPE
A
B
RIGHT
POWER
SWITCH
RIGHT PUSHBUTTON
SWITCH
5
6
3
4
WHITE
BLK/WHT
AUTO
WASH
AUTO
WASH
AUTO
WASH
CORCOM
FILTER
BLUE
OFF
OFF
OFF
RIGHT BEATER
OVERLOAD
RELAY
ORANGE
RED/WHT
A
B
RIGHT BEATER
RELAY COIL
WHITE
A
B
RIGHT COMPRESSOR
RELAY COIL
BLACK/WHITE
B T R
C O M P L 1
L 2
YELLOW
RIGHT
PCB A.
SET SWITCH
TO 240V
BROWN
WHITE/BLACK
RED/WHITE
BROWN/WHITE
WHITE
WHITE/RED
WHITE/BLUE
BLUE/WHITE
GRAY/BLACK
4
BLACK
WHITE
YELLOW
2
1
4
3
RIGHT BEATER RELAY
RIGHT
BEATER MOTOR
(SEE FIG 1)
BLACK
WHITE
BLACK
ORANGE/WHITE
RIGHT SUCTION SOLENOID
RIGHT LIQUID SOLENOID
5
3
RIGHT COMPRESSOR RELAY
BLACK
T3
L3
COMPRESSOR
CONTACTOR
BLACK
BLACK
BLACK
BLACK
COMP
L1
T1
T2
L2
COMPRESSOR
CONTACTOR
COMPRESSOR
CONTACTOR
BLACK
BLACK
FAN
MTR
S T A R T
M A I N
BLACK
432
052145-33
11/18/13
BLACK/WHITE
WHITE
BALLAST
LIGHT SWITCH
RED
RED
L
BLUE
BLUE
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER TERMINAL BLOCK
L1
N
BLK
BLK
LEFT PUSHBUTTON
BLK
WHT/BLK
A
B
LEFT
POWER
SWITCH
SWITCH
5
6
3
4
BLK/WHT
OFF
WHT
AUTO
WASH
AUTO
WASH
AUTO
WASH
CORCOM
FILTER
BLK
BLU
COMPRESSOR
HIGH PRESSURE
SWITCH
LEFT BEATER
OVERLOAD
RELAY
GRN/YEL
ELECTRICAL
ENCLOSURE(S)
OFF
OFF
ORN
A
B
RED/WHT
LEFT BEATER
RELAY COIL
WHT
A
B
LEFT COMPRESSOR
RELAY COIL
BLK/WHT
B T R
C O M P L 1
L 2
YEL
LEFT
PCB A.
SET SWITCH
TO 240V
BRN
WHT/BLK
RED/WHT
BRN/WHT
WHT
WHT/RED
GRN/YEL
BLU/WHT
WHT/BLU
GRA/BLK
4
BLK
YEL
WHT
2
1
4
3
LEFT BEATER RELAY
GRN/YEL
LEFT
BEATER MOTOR
FIG.1
GRN/YEL
WHT
BLK
BLK
ORN/WHT
LEFT SUCTION SOLENOID
LEFT LIQUID SOLENOID
5
3
LEFT COMPRESSOR RELAY
GRN/YEL
6
4
PRP/WHT
WHT/BLK
WHT
LEFT COMPRESSOR RELAY
A1
A2
COMPRESSOR CONTACTOR COIL
6
4
RIGHT COMPRESSOR RELAY
BLK
BLK
A
B
RIGHT
POWER
SWITCH
RIGHT PUSHBUTTON
SWITCH
5
6
3
4
WHT
BLK/WHT
AUTO
WASH
AUTO
WASH
AUTO
WASH
CORCOM
FILTER
BLU
OFF
OFF
OFF
RIGHT BEATER
OVERLOAD
RELAY
ORN
A
B
RED/WHT
RIGHT BEATER
RELAY COIL
WHT
A
B
RIGHT COMPRESSOR
RELAY COIL
BLK/WHT
B T R
C O M P L 1
L 2
YEL
RIGHT
PCB A.
SET SWITCH
TO 240V
BRN
WHT/BLK
RED/WHT
BRN/WHT
WHT
WHT/RED
WHT/BLU
GRN/YEL
BLU/WHT
GRA/BLK
4
BLK
WHT
YEL
2
1
4
3
RIGHT BEATER RELAY
GRN/YEL
WHT
RIGHT
BEATER MOTOR,FIG1
GRN/YEL
BLK
ORN/WHT
RIGHT SUCTION SOLENOID
5
3
RIGHT COMPRESSOR RELAY
GRN/YEL
RIGHT LIQUID SOLENOID
WHT
BLK
WHT
BLK
COMP
FIG.2
L1
T1
T2
L2
S T A R T
M A I N
COMPRESSOR
CONTACTOR
COMPRESSOR
CONTACTOR
GRN/YEL
BLK
BLK
FAN
MTR
GRN/YEL
BLK
BLK/WHT
WHT
432
052145-40
11/18/13
LIGHT SWITCH
YEL BLK CORD
YEL BLK CORD
LED BOX
24 VAC
GRN/YEL
LIGHTING (OPTIONAL-DELETE)
Download from Www.Somanuals.com. All Manuals Search And Download.
|