D00964620A
»
CD-RW900SL
CD Rewritable Recorder
Professional
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
• Do not expose this apparatus to drips or splashes.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
• Do not place any objects filled with liquids, such as
vases, on the apparatus.
• Do not install this apparatus in a confined space such
as a book case or similar unit.
4 Follow all instructions.
• The apparatus draws nominal non-operating power
from the AC outlet with its STANDBY/ON in the
Standby position.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
• The apparatus should be located close enough to the
AC outlet so that you can easily grasp the power cord
plug at any time.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
• An apparatus with Class I construction shall be
connected to an AC outlet with a protective grounding
connection.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
• Batteries (battery pack or batteries installed) should
not be exposed to excessive heat such as sunshine,
fire or the like.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
• Excessive sound pressure from earphones and head-
phones can cause hearing loss.
10 Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
TASCAM CD-RW900SL
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
This product has been designed and manufactured
according to FDA regulations "title 21, CFR, chapter
1, subchapter J, based on the Radiation Control for
Health and Safety Act of 1968", and is classified as
a class 1 laser product. There is no hazardous invis-
ible laser radiation during operation because invis-
ible laser radiation emitted inside of this product is
completely confined in the protective housings.
CAUTION
• DO NOT REMOVE THE PROTECTIVE HOUSING
USING A SCREWDRIVER.
• USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
• IF THIS PRODUCT DEVELOPS TROUBLE,
CONTACT YOUR NEAREST QUALIFIED SERVICE
PERSONNEL, AND DO NOT USE THE PRODUCT
IN ITS DAMAGED STATE.
The label required in this regulation is shown at 1.
1
For USA
• CLASS 1M INVISIBLE LASER RADIATION WHEN
OPEN AND INTERLOCKS DEFEATED. DO NOT
VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
Optical pickup:
Type
: HOP-6201T
Manufacturer : Hitachi Media Electronics Co,Ltd.
Laser output : Less than 75 mW on the objective
lens (record)
Wavelength : 777 to 787 nm
For China
ꢂ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
TASCAM CD-RW900SL
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
1IM−PIOnRtrToAdNuTctSiAoFnETY PRECAUTIONS
own the copyright, or have obtained the appropriate
Thank you for your purchase of the TASCAM
CD-RW900SL CD rewritable recorder.
permission from the copyright holder or the rightful
licensor, your unauthorized recording, reproduction
or distribution thereof may result in severe criminal
penalties under copyright laws and international
copyright treaties. If you are uncertain about your
rights, contact your legal advisor. Under no circum-
stances will TEAC Corporation be responsible for the
consequences of any illegal copying performed using
the CD-RW900SL.
Before connecting and using the unit, please take time to
read this manual thoroughly to ensure you understand how
to properly set up and connect the CD-RW900SL, as well
as the operation of its many useful and convenient func-
tions. After you have finished reading this manual, please
keep it in a safe place for future reference.
NOTE
This product is designed to help you record and repro-
duce sound works to which you own the copyright,
or where you have obtained permission from the
copyright holder or the rightful licensor. Unless you
Supplied accessories
In addition to this manual, the CD-RW900SL has been
packed with the following:
Contact your TASCAM supplier if any of these items are
missing.
NOTE
• RC-RW900SL remote control unit............................1
• AC power cable.........................................................1
• A rack-mounting screw kit (screws and washers).....1
• A warranty card ........................................................1
• AAA batteries for the remote control unit................2
The batteries are not supplied for Taiwan.
Rack-mounting the unit
If you are mounting the unit in a rack, leave 1U of space
above it and 4 inch (10 cm) or more of space at the rear.
Use the rack-mounting kit to mount the unit in a standard
19-inch equipment rack, as shown in this section. Remove
the feet of the unit before mounting.
About this manual
In this manual, we use the following conventions:
• The names of keys and controls are given in the follow-
ing typeface: ERASE.
• When the alphanumeric portion of the display shows
a message, this is shown in the following typeface:
Complete.
• If a preset indicator in the display (i.e. one which cannot
change, but is either on or off) is shown, this is shown as
follows: RANDOM.
• Selectable value (i.e. values of dB) or ON and OFF
selection (i.e. SRC>XXX) is shown in the following
typface: XXX.
ꢄ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY1 −INISnTtRroUdCuTIcOtiNoSn
About CD-R and CD-RW discs
CD-R discs can be recorded once only. Once they
have been used for recording, they cannot be erased or
re-recorded. However, if space is available on the disc,
additional material can be recorded. The pack-aging of
CD-R discs will include one of the following logos:
• CD-R and CD-RW discs are sensitive to the effects of
heat and ultraviolet rays. It is important that they are not
stored in a location where direct sunlight will fall on
them, and which is away from sources of heat such as
radiators or heat-generating electrical devices.
• Always store CD-R and CD-RW discs in their cases to
avoid dirt and dust accumulating on their surfaces.
• When labeling CD-R and CD-RW discs, always use a
soft oil-based felt-tipped pen to write the information.
Never use a ball-point or hard-tipped pen, as this may
cause damage to the recorded side.
• Always keep the recording sides of the discs away from
grime and dust to avoid a reduction in sound quality.
To clean a disc, wipe gently with a soft dry cloth from
the center towards the outside edge. Do not use thinner,
gasoline, benzene or LP cleaning fluid, as these will
damage the disc and cause the disc unplayable.
By contrast, a CD-RW disc can be used in much the same
way as a CD-R disc, but the last track or tracks recorded
can be erased before the disc has been “finalized”, and the
space on the disc can be re- used for other recordings. The
packaging of CD-RW discs will include the logo one of the
following logos:
• Do not put labels or protective sheets on the discs and
do not use any protective coating spray.
• If you are in any doubt as to the care and handling of a
CD-R and CD-RW discs, read the precautions supplied
with the disc, or contact the disc manufacturer directly.
However, you should note that an audio CD created
using a CD-RW disc may not play back satisfactorily on
every audio CD player. It will, naturally, be playable on
the CD-RW900SL. This is in no way a limitation of the
CD-RW900SL itself, but of the difference between the
different types of media and the methods used to read them.
There are precautions that you should take when handling
CD-R and CD-RW discs.
• Avoid touching the recording (non-label) side of a disc on
which you will be recording. Recording on a disc requires
a cleaner surface than playing back, and fingerprints,
grease, etc. can cause errors in the recording process.
About finalizing
Although audio data may be written on a CD-R or CD-RW
disc, a standard CD player will not be able to read the data
(i.e. play back the audio) until a final *TOC has been writ-
ten at the start of the disc.
be written to the disc. See “Finalizing” on page 28 for
details. In the case of a CD-RW disc which has been final-
ized, the whole of the disc may be erased, or the disc may
be “refreshed”, and the disc re-used.
*TOC:Table of contents
Information of recorded data, which contains titles, starting
and ending addresses, and etc..
In addition, a CD-RW disc that has been finalized may be
“unfinalized”, i.e. only the TOC is removed. This allows
further tracks to be recorded to the disc, provided that
there is space on the disc.
The process of writing this table of contents is known as
“finalizing”. Once this has been done, no further data can
Recordable discs
In this manual, we use the term “recordable” disc to
describe a CD-R or CD-RW disc that has not been final-
ized, i.e. further recording is possible on the disc.
TASCAM CD-RW900SL
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
1IM−PIOnRtrToAdNuTctSiAoFnETY PRECAUTIONS
Environmental considerations
The CD-RW900SL may be used in most areas, but to
maintain top performance, and prolong operating life,
observe the following environmental conditions:
• Avoid installing this unit on top of any heat-generating
electrical device such as a power amplifier.
• Make sure that the unit is mounted in a level position for
correct operation.
• The nominal temperature should be between 5°C and
35°C (41°F and 95°F).
NOTE
The voltage supplied to the unit should match the
voltage as printed on the rear panel. If you are in any
doubt regarding this matter, consult an electrician.
• Relative humidity should be 30 to 90 percent.
• As the unit may become hot during operation, always
leave sufficient space above the unit for ventilation. Do
not install this unit in a confined space such as a book-
case, and do not put anything on top of the unit.
Handling of compact discs
The CD-RW900SL has been designed for the playback
of CD-DA (standard audio) format discs and MP3 files
recorded on the discs using the ISO9660 format: In addi
tion to ordinary 5-inch and 3-inch CDs, it can also play
properly recorded CD-R and CD-RW discs.
•
•
Discs should be returned to their cases after use to avoid
serious scratches that could cause the laser pickup to “skip.”
Keep discs away from direct sunlight, and places of
high heat and humidity. If left in such places, warping
could result.
-
•
•
Do not affix any labels or stickers to the label side of the
disc. Do not write on the disc with a ballpoint pen.
Do not insert discs that have adhesive remaining from
tape or stickers that have been removed. If they are
inserted into the player, they could stick to the internal
mechanism, requiring removal by a technician.
Do not use cracked discs.
•
•
Always insert the compact discs into the unit with their
label facing upward.
To remove a disc from its case, press down on the center
of the disc holder, then lift the disc out, holding it care
fully by the edges.
-
•
•
Only use circular compact discs. Avoid using non-circu
lar promotional, etc. discs.
-
•
Avoid getting fingerprints on the signal side (the
non-label side). Grime and dust may cause skipping, so
keep discs clean and store them in their cases when not
being played. To clean the signal side of a disc, wipe
gently with a soft dry cloth from the center towards the
outside edge.
•
Music discs with copy control, a copy-protection
system, have been released from several record compa
-
nies in an attempt to protect the copyright. Since some
of these discs do not comply with the CD specifications,
they may not be playable on the CD-RW900SL.
•
Do not use any record spray, anti-static solutions,
benzene, paint thinner or other chemical agents to clean
CDs as they could damage the delicate playing surface.
It may cause CDs to become unplayable.
Never use a stabilizer or printable discs
Using commercially available CD stabilizers or printable
recordable discs with this player will damage the mecha-
nism and cause it to malfunction.
NOTE
Never use a disc that has had a stabilizer mounted to
it. The residual adhesive may cause the disc to stick
to the turntable of the CD-RW900SL. If it sticks to the
turntable, you will need a technician to get it out.
ꢆ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY1 −INISnTtRroUdCuTIcOtiNoSn
Beware of condensation
If the unit (or a compact disc) is moved from a cold to a
warm place, or used after a sudden temperature change,
there is a danger of condensation; vapor in the air could
condense on the internal mechanism, making correct oper-
ation impossible. To prevent this, or if this occurs, let the
player sit for one or two hours at the new room temperature
before using.
Use of the remote control unit
• Do not expose the infra-red receiver (light receptive
area on the front panel) to direct sunlight or intense light
for extended periods of time. Long exposure to this light
may result in failure of the remote control sensor.
• When the remote control will not be used over one
month, please remove the batteries to prevent the possi-
bility of battery acid leakage which could damage the
unit. Should leakage occur, remove and discard the
batteries, and wipe the battery case thoroughly with a
cloth. Avoid getting the battery liquid on the skin. After
cleaning, replace with new batteries.
• The remote control functions by using an infrared light
signal. When using the unit to control the CD-RW900SL,
other devices that are turned on could be operated by its
signal.
• If the range of remote operation becomes smaller, or
commands do not always function properly, the batter-
ies have become weak and should be replaced. Always
replace both batteries with new batteries of the same type.
• Point the remote control to the remote sensor on the
main unit. Do not obstruct the path between the remote
control and the remote sensor.
Batteries
If batteries are used improperly, or if leakage or breakage
occurs, the unit will not function.
ª
Inserting batteries
1. Open the lid.
Please observe the cautions indicated on the batteries and
their packaging to ensure proper usage.
2. Confirm +/- polarity, and insert two AAA batteries.
3. Close the lid.
• Confirm + and – polarity and follow the indications
when inserting new batteries into the remote control.
• Do not use old and new batteries together.
• Even if the battery is the same size, the voltage may differ.
Do not use batteries of different specifications together.
• Do not attempt to recharge batteries that are
non-rechargeable.
• Do not open or disassemble batteries, throw them into a
fire or put them in water.
Connections
The following should be noted when you connect the unit
to other equipment.
Audio signals output from the unit are output from
the analog ANALOG OUT jacks, as well as from the
DIGITAL COAXIAL OUT jack and DIGITAL OPTICAL
OUT connector simultaneously (but not from the digital
outputs in stop mode).
It is possible to connect the unit’s DIGITAL
COAXIAL IN, DIGITAL OPTICAL IN and ANALOG
UNBALANCED INs (L, R) to other equipment at the
same time. However, the unit can receive signals from only
one digital input at a time.
Currently selected input jack is shown on the display.
TASCAM CD-RW900SL
ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
2IM−PFOeRaTtAuNreTsSoAfFtEhTeYCPDR-ERCWAU90TI0OSNLS
Front panel
1
2
3
4 5 6 789
0
q w
e
r t y u i o p a s d f g
1
2
q
w
e
POWER switch The power switch is used to switch
the unit on and off.
TIMER switch (PLAY, OFF) Using this key switches
Timer play on and off. See “Timer playback” on page
19 for details.
Disc slot Discs should be inserted label side upwards
into the unit’s slot.
INPUT (L,R) controls Use these concentric controls to
adjust the level of the analog audio signals received at
the ANALOG IN jacks.
Gently slide in a disc until the unit pulls the disc in.
Note that if the unit does not pull the disc in, press the
EJECT key to cancel the action. Do not force the disc
in further to avoid damage to the unit.
PHONES jack and the level control Use a standard
pair of stereo headphones, equipped with a 1/4-inch
plug, with this jack.
Adjust the volume from the jack with the level control
(turn clockwise for higher volume).
r
t
y
MULTI JOG dial Use this dial to select tracks for play-
back, to set parameter values.
When a disc is inserted into the unit, the display shows
TOCReadingfor a short period while the unit deter-
mines the contents of the disc.
In addition, pushing the dial acts like an ENTER key, i.e.
the currently-displayed value or setting is confirmed.
3
4
5
6
7
MENU key Use this key to call up the menu options
(see “Operation basics” on page 15).
FINALIZE/INS key Use this key to finalize recordable
discs (see “Finalizing” on page 28).
EJECT key Use this key to eject the currently loaded
disc. The display shows DiscEject.
It also acts like a space key when entering TEXT data
(see “Title input operation” on page 30).
REPEAT key Use this key to set the repeat playback
mode on and off.
ERASE/DEL key Use this key (with CD-RW discs
only) to erase tracks, or a whole disc, or to refresh
a “bad” disc, or to unfinalize a finalized disc (see
“Erasing” on page 29 for details).
ESCAPE key When in a menu mode, this key cancels
the menu item selected.
DISPLAY key Use this key to see the current disc title
when the disc is stopped. When the disc is playing or in
ready mode, press this key to see the current track title.
It also acts like a delete key when entering TEXT data
(see “Title input operation” on page 30).
u ∆ ˙
/
key Use this key to operate review playback
8
9
0
REMOTE SENSOR This is the sensor for the remote
control unit. Make sure that there is a clear path from
the remote control unit to the sensor.
(search) while in playback or ready modes.
When Directory search is on, and when stopped, using
this key selects the directory.
TIME key Use this key to cycle through the time
modes shown on the display (see “Time display switch-
ing” on page 19).
This key also moves the cursor in the left direction
when entering TEXT data.
Display The display is used to show the current status
of the unit, as well as the current menu settings.
i ˚ ¥
key Use this key to operate cue playback
/
(search) while in playback or ready modes.
10
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IM2PO−RFTeAaNtuTrSeAsFoEfTtYheINCSDTR-RUWCT9I0O0NSSL
When Directory search is on, and when stopped, using
this key selects the directory.
f
INPUT SELECT Use this key to select the different
audio inputs and the input combinations (see “Input
selection” on page 23 for full details).
This key also moves the cursor in the right direction
when entering TEXT data.
g
KEYBOARD jack An IBM PC-compatible keyboard
with PS/2 interface can be connected to this terminal to
enable certain operations of the CD-RW900SL with the
keyboard. Title input operations, in particular, can be
performed with greater efficiency.
o
p
STOP key Use this key to stop playback or recording.
PLAY key Use this key to start or resume playback
or recording.
a
s
READY key Use this key to standby for playback
or recording.
RECORD key Use this key to enter record ready mode
(see “Basic recording” on page 24 for details) and also
to enter manual track divisions (see “Manually divide
track” on page 26).
d
SYNC REC key Use this key to turn synchronized
recording on and off before starting to record (see
“Synchronized recording” on page 25 for details).
Rear panel
h ANALOG IN (UNBALANCED) (L, R) These RCA
jacks accept analog audio signals from suitably-
at –
equipped units ( 10 dBV).
j ANALOG OUT (UNBALANCED) (L, R) These RCA
jacks output analog audio signals (at –10 dBV levels) to
suitably-equipped units.
k DIGITAL COAXIAL (IN, OUT) These two RCA jacks
accept and output digital audio in standard consumer
format (SPDIF).
l DIGITAL OPTICAL (IN, OUT) These two TOSLINK
optical connectors accept and output digital audio using
optical fiber connectors.
;
AC IN jack Connects the power cable supplied.
TASCAM CD-RW900SL
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2IM−PFOeRaTtAuNreTsSoAfFtEhTeYCPDR-ERCWAU90TI0OSNLS
Display
This display shows various types of operation information,
including CD disc information, deck operation modes, and
menu status.
% OPTICAL The OPTICAL indicator lights when the input
source is set to optical.
^ COAXIAL The COAXIAL indicator lights when the input
source is set to coaxial.
z TOC The TOC indicator lights up red when a loaded disc
contains TOC (Table of Contents) data.
& ANALOG The ANALOG indicator lights up when the
input source is set to analog.
x Track number display During playback or selection,
the track number is displayed.
* SINGLE The SINGLE indicator lights when Single
Playback mode is set.
When Incremental playback is on, and when in play-
back or playback ready mode, the TRACK indicator blinks.
( RANDOM This RANDOM indicator lights when Random
Playback mode is set.
c MP3 The MP3 indicator lights when a MP3 disc is in
the deck.
) PROGRAM The PROGRAM indicator lights when
Program Playback mode is set.
v Counter display Depending on the time display mode,
TOTAL or REMAIN are lit. The counter display indication
are in minutes (three digits) and seconds (two digits).
Q ¥ This lights during playback, and also blinks during
Auto Cue point search.
b KEY The KEY indicator lights when Key Control is on.
n PITCH The PITCH indicator lights when Pitch Control is on.
m A.CUE The A.CUE indicator lights when Auto Cue is on.
W π This lights during playback or recording standby mode.
E DISC, GROUP, TRACK display The DISC indicator
lights up when a disc loaded and is stopped.
The GROUP indicator lights up when MP3 Directory
playback mode is on.
, A.READY The A.READY indicator lights when Auto
Ready is on.
The TRACK indicator lights up during playback or record-
ing , also during playback or recording standby mode.
. A. TRACK The A.TRACK indicator lights when the Auto
Track is on.
R Character display Disc information, track informa-
tion, menu, message, time, and operation status are
displayed here.
/ Meter This displays the playback level, as well as the
input level of the source device.
! A-B The A-B indicator lights when the A-B repeat func-
tion is on.
T
This lights when the Timer Play function is on.
Also, this flashes until a “B-point” is entered.
Y CAPS The CAPS indicator lights during title input to
indicate CAPS mode is on. In lower case letter mode,
there is no indication.
@ REPEAT The REPEAT indicator lights when the Repeat
function is on.
# SYNC The SYNC indicator lights up when SYNC is on.
$ REC When the SRC function is on, this lights during
recording, or in recording standby mode.
When the SRC function is off, this flashes during
recording, or in recording standby mode.
1ꢀ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IM2PO−RFTeAaNtuTrSeAsFoEfTtYheINCSDTR-RUWCT9I0O0NSSL
RC-RW900SL Remote control unit
q
w
READY key Use this key to standby for playback
or recording.
SYNC REC key Use this key to turn synchronized
recording on and off (see “Synchronized recording” on
page 25 for details).
1
2
e
r
EJECT key Ejects the loaded disc from the unit.
e
r
t
y
u
i
Number keys (0 through 9) Use these keys for direct
entry of track numbers when playing back, or making a
programmed play list.
3
t
CLEAR key Clears a mistaken entry made with the
number keys.
4
5
6
7
8
In the program mode, pressing this key cancels the
program entered at the last.
o
p
a
s
d
It also acts like the ESCAPE key in the Menu mode.
y
ENTER key Pressing this key is equivalent to pressing
the MULTI JOG dial to confirm an entry.
9
0
q
u
i
MENU key Switches the menu mode on or off.
PLAY MODE key Use this key to choose between the
different playback modes (single play, continue play, etc.).
w
o
ERASE key Erases tracks (CD-RW discs only), or a
whole disc, or to refresh a “bad” disc, or to unfinalize a
finalized disc (see “Erasing” on page 29 for details).
p
a
FINALIZE key Finalizes recordable discs. See
“Finalizing” on page 28 for details.
REC MUTE key Use this key when recording, to mute
the input signal for about four seconds and then to enter
record ready mode (see “Rec mute function” on page 27).
1
2
TIME key Press this key to cycle through the time
display modes.
DISPLAY key Press this key to see the current disc
title when the disc is stopped, or the current track title
while in playback or ready mode.
s
d
SKIP (Â/¯) keys Use these keys to move
between tracks when playing back (equivalent to rotat-
ing the MULTI JOG dial).
When entering TEXT data, using this key switches the
text characters.
PLAY key Use this key to start playback, or enter
record mode from record ready mode.
3
REPEAT key Changes between the various repeat
modes when playing back (see “Repeat playback” on
page 19).
4
5
A-B key Sets the A to B repeat points and playback
mode (see “A to B repeat playback” on page 20).
DIRECTORY key Use this key to switch MP3 file
directory playback on and off.
6
7
PITCH key Switches pitch control on and off.
FADER key Use this key to start fade-in recordings or
to start a fade-out when recording (see “Fade-in and
fade-out recording” on page 25 for details).
8
9
RECORD key Use this key to enter record ready mode.
∆ ˚
SEARCH keys ( ) Use these keys to move the
/
playback position inside a track.
0
STOP key Use this key to stop playback or recording.
TASCAM CD-RW900SL
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
3IM−PMOReTnAuNoTpSeAraFtEiToYnPRECAUTIONS
The various settings and editing operations possible with
the CD-RW900SL are performed through menu options
shown on the display. Among the many menu setting
options, some may be made directly using the keys on the
remote control.
Menu configuration
The menus are configured as shown below. Please see the reference page for more details of each menu.
Menu option Sub-Menu option
Function
Reference page
PLAY
PLAY MODE
Playback mode settings
Pitch control mode on/off
Pitch control setting
P18 (“Playback modes”)
PITCH
P20 (“Pitch control function”)
P20 (“Pitch control function”)
P20 (“Pitch control function”)
P21 (“Key control function”)
P21 (“Key control function”)
P21 (“Playing back MP3 files”)
P22 (“MP3 action settings“)
P16 (“Simple playback operations“)
P20 (“Auto Ready function“)
P20 (“Auto Cue function”)
PITCH CONT
PITCH STEP
KEY
Pitch control variable pitch setting
Key control mode on/off
Key control level setting
MP3 disc directory mode on/off
MP3 disc playback error setting
data reading speed setting
Auto ready on/off
KEY LEVEL
DIRECTORY
MP3 ACTION
READ SPEED
A_READY
A_CUE
Auto cue on/off
A_CUE LEVEL
VOLUME
Auto Cue level setting
Input level setting
P20 (“Auto Cue function”)
REC
P23 (“Input selection”)
FADE IN
Fade-in time setting
P25 (“Fade-in and fade-out recording”)
P25 (“Fade-in and fade-out recording”)
P23 (“Frequency conversion”)
P25 (“Sync recording”)
FADE OUT
SRC
Fade-out time setting
Sampling rate converter on/off
Sync recording operating level
Auto track on/off
SYNC LEVEL
A_TRK
P26 (“Automatic track division”)
P26 (“Automatic track division”)
P30 (“Title input operation”)
P31 (“Keyboard type setting”)
P16 (“Simple playback operations”)
P24 (“Basic recording”)
A_TRK LEVEL
TEXT EDIT
KEYBOARD
PLAY TIME
REC TIME
IR REMOTE
F_PRESET
Auto track operating level
Text setting
TEXT
SYSTEM
setting for keyboard type
Display total playing time
Display total recording time
Remote control setting
Reset to the factory setting
P15 (“Operation basics”)
P15 (“Operation basics”)
1ꢂ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SA3FE−TYMIeNnSuTRoUpCeTraIOtiNoSn
Operation basics
1. Select the desired menu option.
3. Setting the desired menu item or value.
Press the MENU key on the front panel or remote
control to call up the desired menu. The menu
option PLAY will be shown on the display at first.
Front panel operation: Use the MULTI JOG dial to
select the desired menu item or value. Pushing the
dial enters and exits menu mode.
Remote control operation: Use the SKIP key.
Pressing the ENTER key confirms and exits menu
mode.
NOTE
Front panel operation: Rotate the MULTI JOG dial
to select the desired menu option, then push the dial
to confirm.
Some menu options exist for confirmation purposes
only, and the setting cannot be changed.
Remote control operation: Use the SKIP key to
cycle through the different menu options, then
press the ENTER key to confirm.
4. How to exit menu mode after setting (or confirma-
tion), during menu option display.
Front panel operation: As well as pushing the
MULTI JOG dial, you can use the MENU key to exit
menu mode.
The sub-menu option screen of the selected menu
will be displayed.
If the PLAY menu option is selected, the sub-menu
option shows up like this:
Remote control operation: Press the ENTER key
to exit menu mode.
NOTE
The selected menu mode remains after power is
turned off, except the TEXT menu.
NOTE
Return to the menu option selection screen, press the
ESCAPE key on the front panel or the CLEAR key on
the remote control.
To reset all the settings and return to the factory setting,
use the F_PRESET sub-menu in the SYSTEM menu
option. It should only be used when a disc is not loaded.
When IR REMOTE is set to Disable, some functions can
not be operated using the remote control. On the other
hand, set to Enable allows any operation using the
remote control.
2. Select the desired sub-menu.
Front panel operation: Rotate the MULTI JOG dial
to select the desired sub-menu, then push the dial to
enter the selection.
Remote control operation: Use the SKIP key to
select, then press the ENTER key.
The menu item screen of the selected sub-menu will
appear. If the sub-menu PLAY MODE is selected,
the menu item shows up like this:
NOTE
To return to the sub-menu option selection screen,
press the ESCAPE key on the front panel or the CLEAR
key on the remote control.
TASCAM CD-RW900SL
1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
4IM−PPOlaRyTAbaNcTkSoApFeErTaYtiPoRnEsCAUTIONS
The CD-RW900SL can be used to play back CDs (includ-
ing CD-R and CD-RW discs that have been recorded and
finalized on other types of recorder), as well as CD-R discs
and CD-RW discs that have been recorded on the unit.
Audio files in MP3 format on CD-ROM, CD-R and
CD-RW are also playable on the unit.
Discs for playback
The CD discs in the CD-RW900SL can play back the types
of discs listed below.
• MP3 files recorded in ISO9660 level 1 and level 2
format on CD-R and CD-RW discs, and properly final-
ized. MP3 files that are recorded to a disc with Joliet
format extensions are also playable.
• Commercial pre-recorded CDs recorded in CD-DA
format.
• CD-R and CD-RW discs that have been recorded in
CD-DA format and finalized properly.
Simple playback operations
The CD-RW900SL also shows one of the following:
WARNING
If you are monitoring using headphones, first adjust
the level control to low on the unit, then connect
to the PHONES jack before playing back. This will
prevent any possible damage to your hearing.
TOC A disc finalized
MP3 A disc contains MP3 files
3. Press the PLAY key to start playback.
NOTE
Adjust the connected monitor system, or the level
control for the PHONES on the unit to set the listen-
ing level you desire.
The explanation in this manual will assume the user is
starting from the normal Continuous mode.
NOTE
1. Press the POWER switch to turn on the unit.
If a disc has scratch or grime, it could cause the laser
pickup to “skip.” In this case, set the READ SPEED
sub-menu in the PLAY menu option to “High“ (see
“Operation basics” on page 15). This may resolve the
problem, however, the unit’s running sound may
become louder.
2. Insert a disc into the unit with the label side up.
The display shows DiscLoading. Then TOC
Readingwill appear with the period flashing.
When the TOC has been read, the display shows the
number of tracks and total running time of the disc.
Disc type
4. To stop playback, press the STOP key.
To temporarily stop playback and enter playback
standby mode, press the READY key. To resume
playback, press the PLAY key again.
NOTE
Total number of tracks Total running time
To confirm the total playing time, use the PLAY TIME
option in the SYSTEM sub-menu (see “Operation
basics” on page 15)
Track selection
Using the skip function
Skipping track numbers backward or forward.
2. Press the PLAY key to start playback.
1. Select desired tracks for playback with the MULTI
JOG dial on the front panel. Turning clockwise
skips the track number backward and counter-
clockwise skips forward.
Or, press the READY key to cue the track and enter
playback standby mode after moving to the head
of the selected track. To start playback, press the
PLAY key.
Or, press the SKIP key on the remote control.
Pressing
key skips the track number back-
Â
ward and
key skips forward.
¯
1ꢄ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT4S−APFlEaTyYbaINckSToRpUeCraTItOioNnSs
Selecting by track number
Using the number keys on the remote control, the number
of the desired track can be entered directory. Even numbers
with two or three digits can be entered easily. For example:
After input, press the PLAY key to start playback. Or, the
READY key to cue the track at its head position and enter
playback standby mode.
Track 9: press ‘9’ and 009 will be displayed.
You can also enter the track number and start playback by
Track 12: press ‘1’ and ‘2’ and 012 will be displayed.
Track 103: press ‘1’ and ‘0’ and ‘3’ and 103 will be displayed.
pushing the MULTI JOG dial or using the ENTER key.
NOTE
This function cannot be used in Program or Random mode.
Track search
Normal search
Press the ∆/˚ search key continuously on the front
panel, or the SEARCH ∆/˚ key on the remote control.
To stop the search function, simply release the ∆/˚ or
the SEARCH key.
NOTE
The search function does not operate with MP3 discs.
Direct search
For MP3 discs, time cannot be specified within a track.
However, if you input the three-digit track number,
playback will begin from the start of that track.
By specifying time from the start of a certain track, you can
start playback from a specified point of a specified track.
ª
Basic operation
During stop, play or playback standby modes, use the
number keys on the remote control to input the three-digit
track number (such as 002 for track 2), then the desired
elapsed time (***min **sec) from the start of that track.
Operation variations
Even if the final “seconds” time value is not input, play-
back will begin from the selected “minutes” time after
pressing the ENTER or PLAY key. Or, if you press the
READY key, the unit will enter the playback standby mode
at the selected point.
Example: To specify 1 min 30 sec from the start of track 2,
input “002 001 30”.
During input, the counter in the display will flash.
ª
Specifying a track number only
After inputting the track number, press the ENTER or
PLAY key to begin playback of that track, or the READY
key to cue the track and enter playback standby mode.
NOTE
Instead of inputting the three-digit track number, you
can input only the desired track number.
NOTE
Example: To specify track 3, input only “3”.
Regardless of the time display mode (see “Time
display switching on page 19), the time from the start
of the specified track is displayed.
ª
Specifying to the minute
After inputting the three-digit track number and the number
of minutes after the start of the track, press the ENTER or
PLAY key to begin playback of that track, or the READY key
to cue the track and enter playback standby mode.
Pressing the CLEAR key cancels the input at any stage
during input.
During stop or playback modes, when the final digit is
entered, the desired position is automatically located and
playback will begin from the desired point. During play-
back standby mode, at the desired point the unit will enter
playback standby mode.
Example: To specify 1 min 00 sec from the start of track 2,
input “002 001”
NOTE
Following the above example, if “0021” is input, the
same position will be located.
NOTE
If a point which does not exist is entered, Direct
Search time entry mode will be cancelled.
The direct search function cannot be used in program
or random mode.
TASCAM CD-RW900SL
1ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
4IM−PPOlaRyTAbaNcTkSoApFeErTaYtiPoRnEsCAUTIONS
Playback modes
There are four different playback modes. The selected
mode will be indicated on the left of the display.
wise changes the playback mode shown on the display in
the following order:
• Continuous playback mode (default setting): no indica-
tion lamp
• Single playback mode: SINGLE is lit
• Program playback mode: PROGRAM red lamp is lit
• Random playback mode: RANDOM red lamp is lit
Mode>Cont Mode>Single Mode>Program Mode>Random
®
®
®
Pressing the MENU key or pushing the MULTI JOG dial
returns to normal mode from the menu mode.
While the mode can be changed from any playback mode,
the explanation in this manual will assume the user is
starting from the Continuous mode.
The playback mode can be selected using the PLAY MODE
key on the remote control unit. Pressing the key changes
the playback mode on the display in the following order:
NOTE
The selected playback mode remains after power is
turned off. However, the program playback mode will
be cleared to “Continuous” mode when the power is
turned off.
Continue Single Program Random
®
®
®
You can also select the playback mode using the PLAY
MODE option in the PLAY sub-menu (see “Operation
basics” on page 15). Turning the MULTI JOG dial clock-
Continuous playback
Programing is cancelled, and playback continues in the
normal order.
2. Press the PLAY key to begin playback in order of
the track number.
1. When stopped, set the mode to display Continue or
Mode>Cont.
Single-track playback
This function enables playback of just a single track.
remote control to select the desired track. The
MULTI JOG dial can be used to select the track also.
1. When stopped, set the mode to display Single or
Mode>Single.
3. Press the PLAY key to begin playback.
2. Use the SKIP key or the number keys (0~9) on the
After the selected track finishes, playback stops.
Random playback
In this mode, the unit will play back all the tracks on the
disc in completely random order, regardless of track number.
NOTE
Even when the power is turned off, the unit will
remain in Random mode.
When stopped, set the mode to display Program or
Mode>Random. Press the PLAY key and random playback
will begin.
Program playback
This function enables playback of selected tracks in
any desired order. Up to 99 tracks can be selected for
program playback.
Repeat the above step 2 until the desired program is complet-
ed. As the program is being created, the program number and
total program playing time is revised on the display.
1. When stopped, set the mode to display Program or
NOTE
Mode>Program.
If the CLEAR key is pressed, the programmed track
will be deleted from the last.
2. Use the number keys (0~9) on the remote control
unit to select each desired track for program play-
back, then press the ENTER key.
3. When program setting is completed, press the
PLAY key to begin playback of the tracks in the
programmed order.
You can also rotate the MULTI JOG dial to select the
track number and push to enter.
NOTE
If the STOP key is pressed without first pressing the
PLAY key, all the program data will be erased.
The track number will be entered into the program.
1ꢆ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT4S−APFlEaTyYbaINckSToRpUeCraTItOioNnSs
When stopped, if the playback mode is switched to
another, all the program data will be erased.
If an attempt is made to enter more than 100 program
steps, the message PGM Full! appears on the display.
The programmed play order is not memorized when
power is turned off.
If the total program playing time exceeds 999 min 59
sec, --- : -- appears on the display.
In this mode, if there are no tracks programed, the
CD-RW900SL will not start playback.
Time display switching
When the TIME key on the front panel or the remote
control is pressed, the time display will switch through
several modes on the display.
NOTE
In program mode, pressing the TIME key displays the
elapsed and the remaining time of the whole program.
• Elapsed track time (no display light indication)
• Remaining track time (REMAIN is lit in the display)
• Elapsed disc time (TOTAL is lit in the display)
• Remaining disc time (TOTAL and REMAIN are lit in the
display)
When playing an MP3 disc, elapsed track time is
always displayed, and the TIME key cannot be used.
For details on time display during recording, please
refer to “Time display while recording” on page 24.
Even when power is turned off, the time display mode
setting is retained.
When stopped, the total recording time is shown, regard-
less of the status of the TOTAL and REMAIN indicators.
Timer playback
By using an external timer, you can set the CD-RW900SL
to play the loaded disc automatically when the unit is
turned on by the timer.
4. Set the timer to the desired time. Consult the timer’
s operation manual for details. At the set time, the
power to the CD-RW900SL will be turned on, and
playback will automatically begin.
1. First, plug the power cord of the CD-RW900SL into
the power outlet of the timer.
2. Load a disc into the unit.
3. Switch the TIMER switch on PLAY to enable timer
function on for the desired deck.
When Timer playback has been turned on, the
timer icon lights up in the display.
Timer indicator
NOTE
The indicator flashes when a disc is not loaded into
the unit.
Repeat playback
1. Press the REPEAT key to turn on the repeat mode.
2. Press the REPEAT key again to turn off repeat
mode. Repeat OFF appears then the REPEAT indicator
turns off.
In this mode, all the tracks on the disc are played
continuously. The display shows Repeat ON and the
indicator lights up REPEAT.
NOTE
Combining the repeat mode with the program,
Single-track playback and Random playback functions
will enable Program repeat, Single-track repeat and
Random repeat operations, respectively.
During playback, if the repeat mode is turned on,
playback continues as before, and when the last track
finishes, playback resumes from the first track.
If the repeat mode is turned on when the deck is
Settings for the repeat playback mode remain after
power is turned off, except the specified A-B section
(see “A to B repeat playback” on page 20).
stopped, press the PLAY key to begin operation.
TASCAM CD-RW900SL
1ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
4IM−PPOlaRyTAbaNcTkSoApFeErTaYtiPoRnEsCAUTIONS
A to B repeat playback
If a specific portion between two points on the disc is spec-
ified, that portion can be played back repeatedly.
NOTE
You can also operate this function during playback standby.
1. During playback, press the A-B key on the remote
control at the beginning of the desired portion on
the disc.
3. To cancel the A-B repeat mode and resume normal
playback, press the A-B key once again.
The REPEAT and A-B indicators will turn off.
The REPEAT indicator lights up in the display and the
A- indicator will flash.
NOTE
A-B repeat cannot be used when the specified A-B
section spans more than one track, and cannot be
used with MP3 discs.
2. At the end of the desired portion on the disc, press
the A-B key again.
Then, the REPEAT and A-B indicators light up in the
display, and the desired A-B section will be played
back repeatedly.
When the STOP key is pressed, the specified A-B
section is cancelled.
Auto Cue function
Using the auto cue function, you can select a cue point
where sound begins (not where a track begins) within a
track.
Then, select a track and press the PLAY key. The unit
enters playback ready mode.
When the PLAY key is pressed again, playback begins at
Turn the auto cue function on and use the A_CUE LEVEL
sub-menu option (see “Operation basics” on page 15) to set
the sound detection level (-24, -30, -36, -42, -48, -54, -60,
-66 and -72 dB).
exactly the cue point.
While the auto function is on, the A.CUE indicator lights up
on the display.
Auto Ready function
This function allows the playing back a single track, and
the automatic cuing of the next track ready for playback.
Combined with Auto Cue function, the unit enters play-
back ready mode at the point where the sound detection
level is set in A_CUE LEVEL sub-menu option of the next
track.
Use the A_READY sub-menu option to turn the function
on or off. When on, the A.READY indicator lights up on the
display.
Pitch control function
increments (default: 0.1%).
When playing back an audio CD, the pitch (or speed) of the
playback can be varied. Pitch can be varied +/- 16%.
3. Press the MENU key or push the MULTI JOG dial to
1. When stopped, press the PITCH key on the remote
enter and return to normal mode.
control to turn on the Pitch control function.
During playback, the pitch control playback can
be disabled temporarily. Press the PITCH key on
the remote control or use the PITCH option in the
PLAY sub-menu to turn the function off.
Or, use the PITCH option in the PLAY sub-menu
(refer to “Operation basics” on page 15).
The current pitch value appears on the display for
seconds and the PITCH indicator will light up.
Pitch>OFFappears on the display and the pitch
control playback will be off temporarily, until the
function is re-set again.
2. Press the MENU key and select the PITCH CONT
option in the PLAY sub-menu to set the desired
value and push the MULTI JOG dial to enter.
To resume the pitch control playback, press the
PITCH key again or use the PITCH option.
Pitch>XXXwill appear on the display.
NOTE
Then, rotate the MULTI JOG dial to set the desired value.
When turning the pitch control on and off during
playback, sound output is cut for a short instant.
NOTE
Use the PITCH STEP option in the PLAY sub-menu to
adjust the pitch value steps from 0.1% to 1.0% in 0.1%
Pitch control cannot be used with MP3 discs.
ꢀ0
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT4S−APFlEaTyYbaINckSToRpUeCraTItOioNnSs
Key control function
The key of the music can be changed during stop, playback
or playback standby modes. However, please note that this
feature does not work with MP3 discs.
NOTE
In this condition, when a CD is played back, the key
of the music is changed while the speed of the music
remains the same.
1. Press the MENU key to select the KEY option in the
PLAY sub-menu (see “Operation basics” on page
15) to enter the function.
Even when the power is turned off, the key change
setting is retained.
Or, press the KEY key on the remote control to set
the function on.
When the Key control function is on, even if the Pitch
control function is used to change the playback speed,
the key of playback will remain fixed at the preset key
{even if the key level is 0 (zero)}, the Key control func-
tion can be turned on.
The KEY indicator will light up.
2. Use the KEY LEVEL option in the PLAY sub-menu
to adjust the playback key level.
When using the key control function, the volume of
the playback sound may occasionally sound like it is
vibrating. This is a result of the key control algorithm
working on the CD playback sound and is normal.
The playback key can be raised or lowered 1/2
octave in half-tone increments. Selection values: 0
(no change), â1 to â6, ã1 to ã6.
3. Rotate the MULTI JOG dial to select the desired key
level and push to enter.
Playing back MP3 files
MP3 files recorded onto a CD are handled the same way as
files are handled in an ordinary PC, with some MP3 files
held within a directory. In addition, several directories can
be combined into one directory. This results in multiple
layers of directories and files.
MP3 files are played in the following order
Disc
Directory
A
When the Directory mode is on, only those files within a
selected directory are available for playback.
Directory
MP3 files
B
When the directory mode is off, the directory configura-
tion is ignored, and all MP3 files recorded on the disc are
available for playback. Please note that Program playback
and Repeat playback only function within directories.
mp3. 1
mp3. 2
mp3. 3
mp3. 4
mp3. 5
NOTE
Each MP3 file is handled as a track.
Directories that do not contain MP3 files directly
under them cannot be selected for playback. For
example, in the diagram below, under directory A are
directory B and directory C. If there are MP3 files in
both directories B and C, directory A cannot be select-
ed for playback, but directory B and C can be selected
for playback.
Directory
C
mp3. 6
mp3. 7
mp3. 8
mp3. 9
Directory
D
The CD-RW900SL can play back MP3 files recorded in
formats that conform to ISO9660 level 1, level 2, and the
Joliet extensions. Discs recorded in multiple sessions may
also be played back.
CDs containing MP3s to be played by the CD-RW900SL,
have their contents must be within the following maximum
limits:
In this manner, playback proceeds from the top level
directories.
Number of directories: 255
Number of hierarchical structures: 8
Number of MP3 files: 999
Title size of MP3 files and directories: 255
TASCAM CD-RW900SL
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
4IM−PPOlaRyTAbaNcTkSoApFeErTaYtiPoRnEsCAUTIONS
About MP3 track data
During playback, titles are displayed in the following order
of priority:
ID3v2 > ID3v1 > file title
When stopped, the file title is displayed.
Directory playback setting
1. Press the DIRECTORY key on the remote control.
3. Press the PLAY key to start playback in the directory.
Or, use the DIRECTORY option in the PLAY
sub-menu to turn this mode on or off (see
“Operation basics” on page 15).
Program or Repeat playback can be operated in the
selected directory also.
NOTE
Pressing the MENU key or pushing the MULTI JOG
dial exits to normal mode.
MP3 file formatted at 44,1 kHz sampling rate and 128
kbps or higher are required, otherwise, that MP3 file
cannot be played back.
NOTE
All MP3 files in a disc can be played back when direc-
tory playback mode is off. The indicator MP3 lights up
and only the total number of track will be shown.
Total number of tracks
2. When stopped, use the MULTI JOG dial or SKIP key
to select desired directory for playback.
MP3 action setting
You can choose whether the unit continues playback or
stop when MP3 playback fails (DecodeErr!).
Select “MP3 ACTION?” sub-menu on the PLAY option.
Select “Skip” or “Stop.”
Skip
When MP3 playback fails, the unit skips the current track
and advances to the next track. Playback will stop if the
current track is the last track (i.e., if the repeat function is
off and the current track is the last track on the disc or in
the program). The display shows DecodeErr!.
Stop
When MP3 playback fails, the unit stops playback. The
display shows DecodeErr!.
ꢀꢀ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY IN5S−TRRUecCoTrIOdiNnSg
Before you start recording using the CD-RW900SL, make
sure that you understand the following key points:
• You can add tracks to an unfinalized recordable disc.
Once finalized, a CD-R disc is “fixed” and behaves in
the same way as a pre-recorded disc. Finalized CD-RW
discs, however, can be erased, refreshed and re-recorded.
• Once you have recorded on a CD-R disc, the data
cannot be erased from it.
Input selection
To select the input to be recorded, press the INPUT
Digital recording level:
SELECT key on the main unit.
The level of the digital signal may be controlled using the
digital volume menu, as described below.
Repeated presses of the key cycle through the following
options:
1. Call up the VOLUME option in the REC sub-menu
(see “Operation basics” on page 15).
ANALOG
OPTICAL
COAXIAL
Analog
Push the MULTI JOG dial to enter the function on.
Optical digital in
Coaxial digital in
2. Rotate the MULTI JOG dial to adjust the input
volume between -54dB and +18 dB (relative to the
original input level).
In the case of either the coaxial or optical inputs being
selected, the indicator COAXIAL or OPTICAL lights up.
There is also a -‹setting which represents a complete
signal cut. The display shows Vol> ---dBfor
the -‹setting.
If the analog signal is selected, the ANALOG indicator lights
on the right of the screen.
3. Press the MENU key or push the MULTI JOG dial to
Analog recording level:
enter the setting and return to normal mode.
The level of the analog signals received at the ANALOG IN
jacks are controlled with the INPUT controls.
When recording analog signals, set the digital volume to
0 dB.
Input monitoring
When the unit is in record ready, or record mode, the input
signal is output from the OUT jacks (digital and analog),
allowing you to hear the input signal.
The word Monitor appears on the display to show that the
output signal is an echo of the input signal(s).
Exit the monitor mode by using the STOP key.
Press the RECORD key on the front panel or the remote
control when a recordable disc is not inserted.
Frequency conversion
The sampling frequency for CDs is 44.1 kHz. The
CD-RW900SL will always record (and play back) CDs at
this frequency.
NOTE
When the SRC function is off, and a digital signal is
received, the display shows the REC indicator flashing
while recording or when in recording standby mode.
However, if recording through a digital connection (coaxial
or optical) and the source has been recorded at a frequency
other than 44.1 kHz, or is being played back at a non-stan-
dard speed using a varispeed unit (more than 1% away
from the standard), the CD-RW900SL’s internal frequency
converter: SRC (Sampling Rate Convertor) will automati-
cally convert the incoming frequency to 44.1 kHz.
The digital signals other than 44.1kHz cannot be
recorded when SRC is off. The error message Not
Fs44.1k!will appear on the display.
To enable the SRC
Press the MENU key and select the SRC? option in the
REC sub-menu (see “Operation basics” on page 15). Rotate
the MULTI JOG dial to select ON. Press the MENU key or
push the MULTI JOG dial to enter.
TASCAM CD-RW900SL
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
5IM−PROeRcToArNdiTnSgAFETY PRECAUTIONS
Basic recording
1. Load a recordable disc into the unit. As the disc
loaded, the display shows TOCReading, with the
period flashing.
4. Press the PLAY key to start recording.
Pressing the READY key stands by recording
temporarily. To restart recording, press the READY
key or PLAY key again.
2. Press the INPUT SELECT key to select a recording
source (see “Input selection” on page 23).
5. Press the STOP key to stop recording.
If a digital source is selected, and the connection
or the signal are improper, the error message
D-IN UNLOCK!will appear on the display.
When recording stops, the display shows
PMAWriting(Program Memory Area) flashing
for a few seconds as the unit writes to the disc.
3. Press the RECORD key. The unit enters record
ready mode, as shown by the REC and READY indica-
tors on the display.
NOTE
When PMA Writing is shown on the display, all keys
are ignored.
NOTE
To confirm the total recording time, use the REC TIME
option in the SYSTEM sub-menu (see “Operation
basics” on page 15).
As the unit enters record ready mode, the display
shows NowOPC(Optimum Power Control) occasion-
ally, as the unit prepares to record on the disc.
To adjust the level of the source, following the
guidelines in “Input selection” on page 23.
NOTE
Do not vibrate the unit or turn off the power when the
unit writes to the disc, otherwise, recording will fail.
NOTE
The red “OVER” indicators on the meters should never
light. Unlike analog equipment, digital audio units
pro-duce extremely unpleasant sounds when distort-
ed, and there is no “headroom” after the 0 mark. If
recording digitally from a commercially-produced
CD, the volume set in the menu should be 0 dB. This
will maintain all the dynamic range of the source CD
without clipping. Only boost the signal if the source is
exceptionally quiet.
An analog signal input at nominal level, with no cut
or boost from the volume controls, is equivalent to a
reading of −16 dB on the meters.
Time display while recording
When in record or record ready mode, repeated presses of
the TIME key cycle through four different time modes:
• Elapsed track time (no display light indication)
• Remaining track time (REMAIN is lit in the display)
• Elapsed disc time (TOTAL is lit in the display)
• Remaining disc time (TOTAL and REMAIN are lit in the
display)
Full disc
If the disc becomes full during recording, the unit will
automatically insert a fade-out. For example: When record-
ing a long program, just before the end of the disc is
reached, the unit starts a fade-out over four seconds and
the display will show Fade Out.
If the disc is a CD-RW, the final track can be erased, if
required (see “Erasing” on page 29) and the disc then
finalized. If the disc is a CD-R, it must be finalized prior
to use (see “Finalizing” on page 28).
When the fade-out has finished, the display shows
Disc Full!. Press the STOP key to exit.
ꢀꢂ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY IN5S−TRRUecCoTrIOdiNnSg
Advanced recording
Fade-in and fade-out recording
At the beginning and end of recording, fade-in and fade-
out effects can be performed.
2. In recording standby mode, press the FADER key
on the remote control.
1. When stopped or when in recording standby mode,
set the operation using the following menu options
on the REC sub-menu (see “Operation basics” on
page 15).
Recording begins and the sound fades in. After the
preset fade-in time, the sound is at normal level.
3. During recording, press the FADER key on the
remote control when you wish to fade-out the sound.
FADE IN?
Fade-out begins with Fade Out flashing on the
display then the unit enters recording standby mode.
The length of the fade in to the normal level can be
set between 1 and 30 seconds in 1-second increments
(default setting: 3 seconds).
4. Press the STOP key and the PMA writing will begin.
FADE OUT?
NOTE
The length of the fade out into complete silence can be
set between 1 and 30 seconds in 1-second incre-ments
(default setting: 3 seconds).
Fade-in or fade-out function can be operated only by
pressing the FADER key on the remote control unit.
The display shows FadeOut>XXsor FadeIn>XXs.
Synchronized recording
Synchronized recording basically means that recording
will begin automatically when a signal is received, and will
stop when the signal ends.
Starting playback of the source automatically starts record-
ing on the CD-RW900SL if Sync function is on (see “Sync
recording” below) and manual record start is disabled.
The SYNC indicator appears on the display.
Sync recording
recording automatically. Otherwise, the unit does not
begin recording even if it is detecting a signal.
1. While recording standby mode, press the SYNC
REC key.
2. Set the signal detection threshold level. Use the
SYNC LEVEL option in the REC sub-menu (see
“Operation basics” on page 15).
When audio signal is not detected for more than five
seconds, the CD-RW900SL automatically will stop record-
ing and enter record standby mode.
Rotate the MULTI JOG dial to adjust the level. The
level can be set from -72 dB to -24 dB in 6 dB incre-
ments. The default setting is -54 dB.
level
REC ready
Five seconds
Press the MENU key or push the MULTI JOG dial to
enter and return to recording standby mode.
S_LVL
3. Input the source signal.
time
Recording begins automatically when the source
signal is detected. The source signal should be high-
er than the adjusted threshold level.
NOTE
When the input level drops below the adjusted thresh-
old level for more than five seconds, recording stops
automatically and enters in recording ready mode.
level
Start of recording
3. To cancel the Sync recording mode, press the
SYNC REC key. Recording returns to normal and
continues till you press the STOP key or the source
signal stops.
S_LVL
Noise level
time
Pressing the STOP key stops recording.
NOTE
The setting remains when the function is set on again.
After SYNC is set, over one second of silence which is
under the adjusted threshold level is required to start
TASCAM CD-RW900SL
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
5IM−PROeRcToArNdiTnSgAFETY PRECAUTIONS
Also remember that when recording from an analog
NOTE
source, the threshold should be set so that it is higher
than the“ noise floor”. If the“ noise floor” is higher
than the threshold, a false start will occur:
If you set the value so that only high-level signals
trigger recording, remember that the start of a piece
may not be record as in the diagram.
Recordsing starts
level
level
Start of track is not registered
This part of the
track may not be
recorded
S_LVL
S_LVL
Noise is higher
than threshold
time
time
Automatic track division
The trigger level can also be used to divide tracks if the
A_TRACK (auto track) function is enabled.
Level
When the sound level has dropped below the threshold
for more than two seconds, and sound has re-started, the
track will be divided.
When this function is enabled, the unit automatically
inserts a track division in the recorded material.
Use A_TRK LEVEL option in the REC sub-menu. The
trigger level is set to -24dB to -72 dB.
At least
ª
To enable or disable automatic track division:
1. Use A_TRK option in the REC sub-menu to set the
mode on. The A.TRACK indicator at the top right of
the display lights.
2 seconds
Track increment
level
2. Rotate and push the MULTI JOG dial to select and
enter the modes following:
A_LVL
DD (digital direct)
time
When recording digitally from MD, CD or DAT, this
mode detects a track boundary and divides the track.
However, when the DD mode is on, and if the analog
source or non-DAT/CD/MD digital connections are
detected, the track number will be incremented using
level detection, as set with the A_TRK LEVEL setting
as described here.
Manually divide track
While recording is taking place, press the RECORD key.
The current track number is incremented by one.
For details of automatic track division while recording, see
“Automatic track division” on page 26.
NOTE
According to the “Red Book” (the specification for
audio CDs), a track cannot be less than four seconds
in length, and there can be a maximum of 99 tracks
on an audio CD. Bear these limitations in mind when
adding track divisions.
This operation can not be applied while recording
track 99.
ꢀꢄ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY IN5S−TRRUecCoTrIOdiNnSg
Rec mute function
The Rec mute function allows instant cut-off of the input
signal, and records four seconds of silence on the disc.
While recording is in progress, press the REC MUTE key
on the remote control.
The display shows the Rec Mute flashing, the meters stop
displaying the current level and the monitored sound is cut.
After about four seconds, the unit enters record ready mode.
NOTE
This function is only available from the remote
control unit.
Restricting the number of tracks
When making a recording, it is possible to restrict the
number of tracks that nay be recorded at one time.
At any time within record or record ready mode, turn
the MULTI JOG dial to display the track numbers you
want to record.
The maximum number that can be entered is 99 tracks.
TASCAM CD-RW900SL
ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
6IM−PAOfRtTeArNreTcSoArdFEinTgY PRECAUTIONS
This section deals with the actions taken after record-ing:
finalizing for CD-R and CD-RW discs, and erase opera-
tions for CD-RW discs.
recorded on them. Even if the disc is full, tracks can be
erased following the unfinalize process, and new material
can be recorded.
Once finalized, CD-R discs are truly final—no more can
be recorded on them. By contrast, CD-RW discs can be
“unfinalized” using the CD-RW900SL, i.e. their TOC can
be deleted, and if there is space, further material can be
Finalizing
As has been explained earlier (“About Finalizing” on page
7), in order for a disc to become a standard CD, it must
have a Table of Contents (TOC) written to it. This process
is known as finalizing.
3. When finalization has been chosen, the display
shows the TOC flashing and the remaining time.
The unit starts counting down from a time shown
on the display.
An unfinalized disc can always be distinguished on the
CD-RW900SL by the TOC indicator under the disc type on
the display being unlit when the disc is inserted.
4. When finalization has been finished successfully,
Completeappears and the TOC will be lit on
the display.
NOTE
To finalize a disc:
During the finalizing process, all key presses are ignored.
1. Load the unfinalized disc, and with the unit in stop
mode, press the FINALIZE key.
The display shows FINALIZE?
If you do not want to proceed with the finalizing
process, press the FINALIZE/INS key on the front
panel or the FINALIZE key on the remote control.
2. To start the finalizing process, push the MULTI JOG
dial or press the ENTER key on the remote control.
The display shows Sure?
If you do not want to proceed with the finalizing
process, press the STOP key.
Unfinalizing CD-RW discs
If a CD-RW disc has been finalized, it is possible to erase
the Table of Contents in the following way:
3. To start the unfinalizing process, press the MULTI
JOG dial or the ENTER key again.
1. With the finalized disc loaded and the unit in stop
mode, press the ERASE/DEL key on the front panel
or the ERASE key on the remote control.
When unfinalization has been chosen, the display
shows Eraseflashing and the remaining time.
The unit starts counting down from a time shown
on the display.
Rotate the MULTI JOG dial or press the SKIP key
on the remote control to select UNFINALIZE?.
Push the MULTI JOG dial or press the ENTER key
to confirm.
4. When finalization has been finished successfully,
Completeappears on the display, and the TOC indi-
cator will go off.
If you do not want to proceed with the unfinaliz-
ing process, press the ERASE/DEL key on the front
panel or the SKIP key on the remote control.
2. The display shows Sure?
If you do not want to proceed with the unfinalizing
process, press the STOP key.
ꢀꢆ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAF6ET−YAIfNteSTrRrUecCoTrIOdiNnSg
Erasing
Erasing tracks
This operation erases the specified track and all sub-sequent
tracks from a recorded CD-RW disc.
the first track and last track to be erased).
Rotate the MULTI JOG dial or press the SKIP key to
change the track numbers you desire to erase.
NOTE
Once this operation has started, the STOP key cannot
be used to cancel it. Please check the track range to be
deleted first.
To cancel the operation at this point, press the
ERASE/DEL or the ERASE key again.
3. Push the MULTI JOG dial or press the ENTER key to
Erasing track is operated only when unit is in continu-
os playback.
operate the function.
The display shows Sure?
1. While stopped, press the ERASE/DEL key on
the front panel or the ERASE key on the remote
control. Select the ERASE TRACK?rotating
the MULTI JOG dial or pressing the SKIP key on the
remote control.
To cancel the operation at this point, press the
STOP key.
4. Push the MULTI JOG dial or press the ENTER key
again to proceed the operation.
To cancel the operation at this point, press the
ERASE/DEL or the ERASE key again.
The display shows Erase flashing and the remaining
time. The unit starts counting down from a time
shown on the display.
2. Push the MULTI JOG dial or press the ENTER key
to enter the function.
5. When the tracks have been erased, Completewill
appears on the display.
The display shows EraseXX-XX(the number of
Erasing a whole disc
When you want to erase a whole disc (all the tracks on a
disc), follow the procedure below:
2. Push the MULTI JOG dial or press the ENTER key
to enter the function. The display shows Sure?
To cancel the operation at this point, press the
NOTE
STOP key.
Once the operation is proceeded, the STOP key
cannot function. Please confirm before the operation.
3. Push the MULTI JOG dial or press the ENTER key
again to proceed the operation.
1. While stopped, press the ERASE/DEL key on the
front panel or the ERASE key on the remote control.
Select the ERASEDISC?by rotating the MULTI
JOG dial or pressing the SKIP key on the remote
control.
The display shows Erase flashing and the remaining
time. The unit starts counting down from a time
shown on the display.
4. When the disc has been erased, Completeappears
then BlankDiscwill appear on the display.
To cancel the operation at this point, press the
ERASE/DEL or the ERASE key again.
Refreshing a disc
Refreshing the disc makes a disc usable again. This opera-
tion destroys all data on the disc.
To cancel the operation at this point, press the
STOP key.
1. Load the disc, and the unit in stop mode, press the
ERASE/DEL key on the front panel or the ERASE
key on the remote control. Select the REFRESH?
rotating the MULTI JOG dial or pressing the SKIP
key on the remote control.
3. Push the MULTI JOG dial or press the ENTER key
again to proceed the operation.
The display shows Erase flashing and the remaining
time. The unit starts counting down from a time
shown on the display.
To cancel the operation at this point, press the
ERASE/DEL or the ERASE key again.
4. Whenthedischasbeenrefreshed, Completeappears
thenBlank Discwillappearonthedisplay.
2. Push the MULTI JOG dial or press the ENTER key
on the remote control to enter the function. The
display shows Sure?
TASCAM CD-RW900SL
ꢀꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
7IM−PTOitRlTinAgNT SAFETY PRECAUTIONS
the titles will not have be added. You must finalize
the disc to save the titles.
Titles can be given to the disc and the tracks on the disc,
using the TEXT EDIT option on the TEXT sub-menu.
NOTE
After a new title is selected and entered on the disc,
TOC will light up on the display. If the power is turned
off, the TOC has not been recorded on the disc and
Title input operation
Follow the guidelines below to input titles on the screen.
Operate them when in the text edit mode.
To insert characters
Move the cursor to the location where you wish to insert
a character, and press the FINALIZE/INS key on the
front panel or the FINALIZE key on the remote control.
It is more efficient to connect a keyboard for title input ( see
“Title input by keyboard” on page 31).
To change a character
Place the cursor on the character to be changed, then
input the desired character.
Select the type of character for input
Press the DISPLAY key on the unit or the remote control
to select from two different types of characters.
Lower case letters/code: no indication
Capital letters/code: CAPS
NOTE
As with the TEXT menu, if you attempt to eject the
disc without writing the TOC to the disc, the display
will show Sure?Text!. If you want to eject the disc
without performing a TOC write, press the EJECT key
while “Sure Text!” is shown on the display. The text
that have been edited or entered will be abandoned.
Input procedure
Rotate the MULTI JOG dial or the SKIP key on the remote
control to get the desired characters on the display.
Push the MULTI JOG dial or press the ENTER key on
the remote control to enter.
To move the cursor position
Use the ∆/˙ key and the ˚/¥ key on the front
panel, or the SEARCH key on the remote control.
The disc or track title on a finalized disc cannot be
edited. Unfinalizing (CD-RW only) is needed in this
case to use the title input function.
To delete characters
Place the cursor on the character, then press the
ERASE/DEL key on the front panel, or the ERASE key
on the remote control.
Disc title input
1. While stopped, select the TEXT EDIT option in the
TEXT sub-menu (see “Operation basic” on page
15). Text>Discwill appear.
3. Press the MENU key to enter.
If you want to cancel, press the STOP key.
2. Press the MULTI JOG dial or the ENTER key on the
remote control.
Now, you can input or edit the disc title following
the guidelines above.
Track title input
1. While stopped, select the TEXT EDIT option in the
TEXT sub-menu (see “Operation basic” on page 15).
4. Press the MENU key to enter.
If you want to cancel, press the STOP key.
2. Rotate the MULTI JOG dial or repeatedly press the
SKIP keys on the remote control to select the track
number you wish to title.
3. Push the MULTI JOG dial or press the ENTER key
on the remote control.
Now, you can input or edit the track title following
the guidelines above.
ꢁ0
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTR7U−CTTiItOliNnSg
Using a keyboard with the CD-RW900SL
A computer keyboard can be connected to the IBM PC
compatible PS/2 interface on the front panel to operate
certain functions of the CD-RW900SL. It is particularly
efficient for title input.
Keyboard type setting
The CD-RW900SL must be set for the type of keyboard
being connected.
Set the type using the sub-menu KEYBOARD option on the
SYSTEM sub-menu. Select US for an English-language
keyboard, or JP for a Japanese-language keyboard.
Title input by keyboard
Titles can be input just like typing on a PC.
To delete characters
Delete key: deletes the character in the cursor position
To enter the Title Edit menu
Back space key: deletes the character before the cursor
position
Press SHIFT + F8 to enter the Disc/Track Title Edit Menu.
To select the type of characters for input
Press CAPS to select or cancel upper case letters
To insert a character
Use the Insert key.
To input characters
Character input is performed directly with the letter and
number keys.
To change a character
Put the cursor on its position and input the desired character.
To move the cursor
Use the cursor arrow keys
Other keyboard operations
The keyboard can be used not only for title input, but also
to control the deck transports, perform editing functions
and other operations. The list below shows the keys that
perform various operations.
Keyboard key
F1
Operation
Keyboard key
SHIFT + F11
SHIFT + F12
CTRL + F1
CTRL + F2
CTRL + F3
CTRL + F4
CTRL + F5
CTRL + F6
CTRL + F7
CTRL + F8
CTRL + F9
CTRL + F10
CTRL + F11
CTRL + F12
CAPS
Operation
same as pressing the µ key
same as pressing the ≤ key
same as pressing the Key key
same as pressing the STOP key
same as pressing the PLAY key
same as pressing the READY key
set the Auto Cue on or off
direct to “UNFINALIZE?”
F2
direct to “FINALIZE?”
F3
Direct track search TRACK 1
Direct track search TRACK 2
Direct track search TRACK 3
Direct track search TRACK 4
Direct track search TRACK 5
Direct track search TRACK 6
Direct track search TRACK 7
Direct track search TRACK 8
Direct track search TRACK 9
Direct track search TRACK 10
Direct track search TRACK 11
Direct track search TRACK 12
select or cancel upper case letters
to move the cursor
F4
F5
F6
F7
F8
same as pressing the RECORD key
set the Auto Ready on or off
same as pressing the REPEAT key
same as pressing the P.MODE key
same as pressing the PITCH key
direct to “ERASETRACK?”
direct to “ERASEDISC?”
F9
F10
F11
F12
SHIFT + F1
SHIFT + F2
SHIFT + F3
SHIFT + F4
SHIFT + F5
SHIFT + F6
SHIFT + F7
SHIFT + F8
SHIFT + F9
SHIFT + 10
direct to “REFRESH?”
å/œ
Delete
same as the DEL or CLEAR key
deletes the character before the cursor
same as the FINALIZE/INS key
Back space
Insert
direct to “TEXTEDIT?”
ESC
cancel edit or title edit and finis Menu
mode
Enter
same as the ENTER key
TASCAM CD-RW900SL
ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
8IM−PROeRfTeAreNnTcSeAaFnEdTYspPeRcEiCfiAcaUtTiIoOnNsS
Error messages
Message
Details / response
Can’t Rec!
Cannot record. Either erase the contents of the disc (for a CD-RW), or use a
different recordable disc.
Disc Error!
Disc Full!
Text Full!
The disc has malfunctioned. Please replace with a new disc.
No recording time remaining, or no recordable track is left on the disc.
No space to input the letters.
Sure? Text!
The text data is not written on the disc yet. Eject the disc to cancel the text
you entered or perform the finalize operation to write the data to the disc.
Drive Error!
There is a problem in the drive.
D-IN UNLOCK!
The digital input is not connected. Turn on the power of the equipment
connected to DIGITAL IN.
Not Audio!
Erase Error!
Not Fs44.1k!
There is no audio signal from DIGITAL IN.
An error occurred while erasing.
The sampling frequency of the digital input is not 44.1 kHz. Please turn the
SRC on.
PGM Empty!
PGM Full!
Can’t Edit!
Can’t Sel!
Rec Error!
OPC Error!
No DIR!
There is no program.
No new programs can be created.
Editing cannot be performed due to operational restrictions.
Menu selection cannot be performed due to selection restrictions.
There was an error during recording. Please re-record.
There was an error during OPC. Please re-record.
There is no directory that contains a file.
Decode Err!
Format Err!
IR Disable!
The MP3 file cannot be played back.
The disc is in a format that the CD-RW900SL cannot read.
Remote control operation is not allowed.
Messages during operations
Message
Blank Disc
Complete
Statement
A blank recordable disc has been inserted.
An operation such as finalize or erase has been successfully completed.
Calibration is being performed to operate recording properly.
Now OPC*
Disc Repair
The disc is being repaired, and this operation will take a long time. Please do not turn off the power
of the CD-RW900SL until it finishes.
PMA Writing*
TOC Reading
The recorded content is being written to the disc.
The table of contents data is being read.
*OPC=Optimum power Control
*PMA=Program memory Area
ꢁꢀ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IM8P−ORRTeAfeNrTeSnAceFEaTnYdINspSeTcRiUfiCcaTItOioNnSs
Troublshooting
Symptom
Possible cause and remedy
There is no power to the unit.
“Disc Error!”, or “OPC Error!” is displayed.
Playback is not possible.
Please check the power cord is properly plugged in.
The disc may be dirty. Please replace the disc.
This may be due to condensation. In this case, remove the disc, turn the
power on and wait a few hours, then try again.
No sound is output.
• Confirm the connections with the audio system.
• Check the volume level, and proper amplifier operation.
Recording is not possible.
• Confirm the connections with the audio system.
• Adjust the recording level.
• The disc may be for playback only. Please replace with a recordable disc.
Noise or static can be heard.
Please re-position the unit away from strong source of magnetism such
as a television.
The unit does not retain settings.
While settings are retained each time they are made, in some case they
will not be retained when the power is turned off too soon. To prevent
this from happening, do not turn off the power right after making a seting.
Can’t insert a disc.
Take the disc out and press the EJECT key to reset. Then try again.
Never use force to insert the disc into the slot.
TASCAM CD-RW900SL
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
8IM−PROeRfTeAreNnTcSeAaFnEdTYspPeRcEiCfiAcaUtTiIoOnNsS
Specifications
Recordable discs
CD-R, CD-R-DA, CD-RW, CD-RW-DA (High speed CD-RW is supported)
Quantization bit depth
Sampling frequency
Frequency response
16 bit
44.1 kHz
20 Hz~20 KHz
0.8 dB (playback)
1.0 dB (recording)
S/N
95 dB (playback)
90 dB (recording)
Dynamic range
Distortion
95 dB (playback)
90 dB (recording)
0.006 % (playback)
0.008 % (recording)
Channel separation
90 dB (playback)
80 dB (recording)
Wow and flutter
Analog inputs
< 0.001 % (unmeasurable)
Unbalanced RCA pin
Level -10 dBV 2 dB (Full Scale -16 dB)
Minimum input level -19 dBV (adjustable level at Full Scale -16 dB)
Input impedance 22 KØ 10% (unbalanced)
Analog outputs
Phones output
Unbalanced RCA pin
Level -10 dBV 2 dB (Full Scale -16 dB)
Maximum output level +6 dBV 2 dB
Output impedance 600 Ø 10% (unbalanced)
Stereo (6.3 ø)
20 mW
32 Ø
Digital input
Coaxial RCA pin jack (IEC-60958 Consumer use)
Optical TOSLINK (IEC-60958 Consumer use)
Digital output
Coaxial RCA pin jack (IEC-60958 Consumer use)
Optical TOSLINK (IEC-60958 Consumer use)
Keyboard
Power
Mini DIN 6 pin
U.S.A./Canada 120 VAC, 60Hz
U.K./Europe
Australia
230 VAC, 50Hz
240 VAC, 50Hz
Power consumption
16 W (U.S.A./Canada)
18 W (U.K./Europe/Australia)
Dimensions (d x w x h)
Weight
307.6 x 482.6 x 94 (mm) / 12.1 x 19.0 x 3.7 (in)
4.5 kg (10 lb)
ꢁꢂ
TASCAM CD-RW900SL
Download from Www.Somanuals.com. All Manuals Search And Download.
IM8P−ORRTeAfeNrTeSnAceFEaTnYdINspSeTcRiUfiCcaTItOioNnSs
Dimensional drawing
482.6mm(19.0")
465.6mm(18.3")
435.0mm(17.1")
307.6mm(12.1")
284.6mm(11.2")
16.6mm(6.5")
6.4mm(0.3")
TASCAM CD-RW900SL
ꢁꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
»
CD-RW900SL
TEAC CORPORATION
Phone: +81-422-52-5082
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
Printed in China
7733 Telegraph Road, Montebello, California 90640
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. De C.V
Phone: +52-555-581-5500
Campesinos No. 184, Colonia Granjes Esmeralda, Delegacion Iztapalapa CP 09810, Mexico DF
TEAC UK LIMITED
Phone: +44-8451-302511
Unit 19 & 20, The Courtyards Hatters Lane, Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Download from Www.Somanuals.com. All Manuals Search And Download.
|
