D01124920A
DR-V1HD
HD Video / Linear PCM Recorder
®
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
•
•
•
The apparatus draws nominal non-operating power from the AC outlet
with its POWER or STANDBY/ON switch not in the ON position.
The mains plug is used as the disconnect device, the disconnect device
shall remain readily operable.
Caution should be taken when using earphones or headphones with the
product because excessive sound pressure (volume) from earphones or
headphones can cause hearing loss.
If you are experiencing problems with this product, contact TEAC for a
service referral. Do not use the product until it has been repaired.
8
9
•
CAUTION
•
•
Do not expose this apparatus to drips or splashes.
Do not place any objects filled with liquids, such as vases, on the
apparatus.
10 Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
•
•
•
Do not install this apparatus in a confined space such as a book case or
similar unit.
The apparatus should be located close enough to the AC outlet so that
you can easily grasp the power cord plug at any time.
If the product uses batteries (including a battery pack or installed
batteries), they should not be exposed to sunshine, fire or excessive heat.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
WARNING
Products with Class construction are equipped with a power supply cord
that has a grounding plug. The cord of such a product must be plugged into
an AC outlet that has a protective grounding connection.
13 Unplug this apparatus during lightning storms or when unused for long
periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
3
Safety Information
For European Customers
8
Disposal of batteries and/or accumulators
Disposal of electrical and electronic equipment
(a) Waste batteries and/or accumulators should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
(a) All electrical and electronic equipment should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
(b) By disposing of waste batteries and/or accumulators correctly, you will
help save valuable resources and prevent any potential negative effects
on human health and the environment.
(b) By disposing of the electrical and electronic equipment correctly, you will
help save valuable resources and prevent any potential negative effects
on human health and the environment.
(c) Improper disposal of waste batteries and/or accumulators can have
serious effects on the environment and human health as a result of the
presence of hazardous substances in batteries and/or accumulators.
(c) Improper disposal of waste equipment can have serious effects on the
environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment.
(d) The crossed out wheeled dust bin symbol indicates that batteries and/
or accumulators must be collected and disposed of separately from
household waste.
(d) The crossed out wheeled dust bin symbol indicates that electrical and
electronic equipment must be collected and disposed of separately from
household waste.
If the battery or accumulator contains more than the specified values
of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery
Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury
(Hg) and/or cadmium (Cd) will be indicated beneath the crossed out
wheeled dust bin symbol.
(e) The return and collection systems are available to the end users. For
more detailed information about disposal of old electrical and electronic
equipment, please contact your city office, waste disposal service or the
shop where you purchased the equipment.
Pb, Hg, Cd
(e) The return and collection systems are available to the end users. For
more detailed information about disposal of waste batteries and/or
accumulators, please contact your city office, waste disposal service or
the shop where you purchased them.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
4
Safety Information
•
•
•
Do not carry or store batteries together with small metal objects. The
batteries could short, causing leak, rupture or other trouble.
Do not heat or disassemble batteries. Do not put them in fire or water.
Batteries could rupture or leak, causing fire, injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the battery case before
inserting new batteries. If the battery fluid gets in an eye, it could
cause loss of eyesight. If fluid does enter an eye, wash it out thoroughly
with clean water without rubbing the eye and then consult a doctor
immediately. If the fluid gets on a person’s body or clothing, it could cause
skin injuries or burns. If this should happen, wash it off with clean water
and then consult a doctor immediately.
CAUTIONS ABOUT BATTERIES
This product uses batteries. Misuse of batteries could cause a leak, rupture
or other trouble. Always abide by the following precautions when using
batteries.
•
Never recharge non-rechargeable batteries. The batteries could rupture or
leak, causing fire or injury.
•
When installing batteries, pay attention to the polarity indications
(plus/minus (+/–) orientation), and install them correctly in the battery
compartment as indicated. Putting them in backward could make the
batteries rupture or leak, causing fire, injury or stains around them.
•
When you store or dispose batteries, isolate their terminals with insulation
tape or something like that to prevent them from contacting other
batteries or metallic objects.
•
•
The unit power should be off when you install and replace batteries.
Remove the batteries if you do not plan to use the unit for a long time.
Batteries could rupture or leak, causing fire, injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the battery compartment
before inserting new batteries.
Do not disassemble a battery. The acid inside the battery could harm skin
or clothing.
•
•
When throwing used batteries away, follow the disposal instructions
indicated on the batteries and the local disposal laws.
Do not use batteries other than those specified. Do not mix and use new
and old batteries or different types of batteries together. The batteries
could rupture or leak, causing fire, injury or stains around them.
•
For China
8
产品有毒有害物质或元素的名称及含量
机种：DR-V1HD
有毒有害物质或元素
铅
汞
(Hg)
○
镉
六价铬
(Cr(VI))
多溴联苯
多溴二苯醚
(PBDE)
品名
(Pb)
○
(Cd)
○
(PBB)
○
○
1
2
3
4
7
8
CHASSIS部份
PCB Assy部份
线材部份
○
○
○
○
○
○
○
○
○
○
○
○
×
○
○
○
○
○
○
○
附属品部份
SEAL部份
包装部份
×
○
○
○
○
○
○
○
○
○
○
○：表示该有毒有害物质在该部件所有均质材料中的含有量均在 SJ/T11363-2006 标准规定的限量要求以下。
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
（针对现在代替技术困难的电子部品及合金中的铅 )
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
5
Contents
Turning the power ON and OFF ...........................................................................30
Turning the power ON ...................................................................................30
Removing the card.......................................................................................... 33
Using the built-in speaker ......................................................................................34
Conventions used in this manual........................................................................ 10
Beware of condensation......................................................................................... 13
image resolution........................................................................................................36
Connecting an external mic or device ..............................................................40
Recording (video/audio)......................................................................................... 43
Photo mode........................................................................................................23
Menu structure ..........................................................................................................25
Using menus................................................................................................................ 26
Powering the unit...................................................................................................... 29
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
6
Contents
Setting the white balance...................................................................................... 49
Adding files to a playlist................................................................................66
Editing a playlist ..............................................................................................66
Skipping to select files for playback ..................................................................68
Playback.........................................................................................................................68
Looping playback ..................................................................................................... 71
Setting the operation mode .................................................................................54
Setting the image size .............................................................................................54
Set where to save photo files ...............................................................................54
Navigating the BROWSE screen........................................................................... 56
Thumbnail display mode.............................................................................. 57
Folder operations ......................................................................................................60
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
7
Contents
System settings (SETUP screen)........................................................................... 81
Media and formats.................................................................................................... 89
Inputs and outputs .................................................................................................. 89
Digital connections.........................................................................................90
Audio performance...................................................................................................90
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
8
1 – Introduction
Thank you very much for purchasing a TASCAM DR-V1HD HD Video/Linear
PCM Recorder.
Please read this Owner’s Manual carefully in order to maximize your use of all
the unit’s features. We hope that you will enjoy using this recorder for many
years to come. After you have finished reading this manual, please keep it in a
safe place for future reference.
•
File incrementing and auto-recording functions can be used together to
create new files when desired without interrupting recording (audio or
video)
Pre-recording function allows capture of up to 2 seconds of audio or video
before recording is activated manually
Automatic gain control function automatically adjusts input levels to make
recording levels as uniform as possible
Limiter function automatically reduces the input level suitably when it is
too high
•
•
•
You can also download this Owner’s Manual from the TASCAM website (http://
tascam.com/).
•
•
Low cut filter function reduces low-frequency noise
VSA function changes playback speed from 50% to 150% (in 10%
increments) of normal speed without changing pitch
Repeat playback and IN-OUT loop playback functions
Playlist function
Auto power-off function can be set to 3, 5, 10 or 30 minutes, or OFF
Divide function allows files to be split where desired
File name format can be set to use a user-defined word or the date
1/8" input jack for line input and external stereo microphones can provide
plug-in power
1/8" line/headphones output jack
Mini-B type USB 2.0 port
Operates on 3 AA batteries or a TASCAM PS-P520 AC adapter (sold
separately)
Tripod attachment socket built into unit
Features
•
Compact HD video and linear PCM recorder uses microSD/SDHC cards as
recording media
Directional microphones enable high-quality stereo recording
Supports 1280 x 720p HD mode
Camera lens and microphone can be rotated 180 degrees, enabling self-
recording
1x to 4x digital zoom (in 0.1 increments)
Video, audio and photo modes
Can take still pictures as a digital camera
Linear PCM (WAV format) recording possible at 44.1, 48 or 96 kHz and 16
or 24-bit
HD video display on a TV possible using the mini-HDMI PORT (Type C)
2.4-inch 240x320 TFT Color LCD display
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Can show slide shows with 1-10 second intervals between still images
Using the After Rec function, while playing back a recorded video file you
can overwrite the playback sound with the input sound and record it as a
new file
•
•
Built-in 0.6W mono speaker
Allows monitoring througws recording (audio or video) to start
automatically when the set audio input level is detected
•
When the 2GB maximum file size is reached, audio and video recording can
automatically continue in a new file without interruption
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
9
1 – Introduction
Items included with the product
Conventions used in this manual
The DR-V1HD package contains the following items.
The following conventions are used in this manual.
Take care when opening the package not to damage the items. Keep the
package materials for transportation in the future.
•
Names of buttons, controls and other physical parts of this unit and other
devices appear like this: MENU
Please contact TASCAM if any of these items are missing or have been
damaged during transportation.
•
•
Text displayed on the unit’s screen appears like this: ON
The three buttons (F1, F2 and F3) under the display are function buttons.
Functions shown at the bottom of screens will sometimes be shown next
to button names.
•
•
•
•
•
Main unit.............................................................................................. ×1
microSD card (inside unit)............................................................. ×1
AA alkaline batteries ...................................................................... ×3
USB cable (0.8 m).............................................................................. ×1
Owner’s Manual (this document) ............................................... ×1
•
•
•
•
Example: F1(
) button (YES)
“microSD memory card”is sometimes abbreviated as “microSD card”.
Text displayed on a computer monitor appears like this: “OK”
Additional information is introduced under the following headings.
TIP
These are hints and tipse same n about ways to use the DR-V1HD.
NOTE
These provide additional explanations for special situations.
CAUTION
These indicate that a person could be injured, the device could be damaged,
or data (recordings) could be lost if you do not follow the instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
10
1 – Introduction
Trademarks
Any data, including, but not limited to information, described herein are
intended only as illustrations of such data and/or information and not
as the specifications for such data and/or information. TEAC Corporation
disclaims any warranty that any use of such data and/or information
shall be free from infringement of any third party’s intellectual property
rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from
or connected with or related to the use of such data and/or information.
•
•
TASCAM is a trademark of TEAC Corporation, registered in the U.S. and
other countries.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC
in United States and other countries.
•
microSDHC Logo is a trademark of SD-3C, LLC.
This product is designed to help you record and reproduce sound
works to which you own the copyright, or where you have obtained
permission from the copyright holder or the rightful licensor. Unless
you own the copyright, or have obtained the appropriate permission
from the copyright holder or the rightful licensor, your unauthorized
recording, reproduction or distribution thereof may result in severe
criminal penalties under copyright laws and international copyright
treaties. If you are uncertain about your rights, contact your legal advisor.
Under no circumstances will TEAC Corporation be responsible for the
consequences of any illegal copying performed using the recorder.
•
Microsoft, Windows, Windows XP, Windows Vista, and Windows 7 are
either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Apple, Macintosh, iMac, Mac OS and Mac OS X are trademarks of Apple Inc.
Other company names, product names and logos in this document are the
trademarks or registered trademarks of their respective owners.
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
11
1 – Introduction
About microSD cards
Precautions for placement and use
This unit uses microSD cards for recording and playback.
You can use 64 MB–2 GB microSD cards and 4 GB–32 GB microSDHC cards
with this unit.
•
•
The guaranteed operating temperature range is between 0º C and 35º C
Do not install in the following types of places. Doing so could degrade the
sound quality and/or cause malfunctions.
Operation with all microSD cards is not guaranteed.
•
•
•
•
•
•
•
Places with significant vibrations
A list of microSD cards that have been tested with this unit can be found on
the TASCAM website (http://tascam.com/). You can also contact TASCAM
Customer Support.
Near windows or other places exposed to direct sunlight
Near heaters or other extremely hot places
Extremely cold places
Places with bad ventilation or high humidity
Very dusty places
Precautions for use
microSD cards are delicate media. In order to avoid damaging cards or the
card slot, please take the following precautions when handling them.
Places exposed to rainfall or other direct water
•
If this unit is placed near equipment that contains a large transformer,
such as a power amplifier, a humming sound could occur. In such a
case, increase the distance or between the equipment or change their
orientations.
If this unit is operated near a TV or radio, color irregularity might occur on
the TV screen or noise might be generated by the radio. If this occurs, move
this unit away from the other device.
If a cell phone or other wireless equipment is used close to this unit, the
operation of the mobile equipment might cause noise in this unit. In such a
case, keep such devices away from this unit or turn them off.
•
•
•
•
•
Do not leave in extremely hot or cold places.
Do not leave them in extremely humid places.
Do not let them get wet.
Do not put things on top of them or twist them.
Do not subject them to great force.
•
•
•
•
Avoid installing this unit on top of any heat-generating electrical device
such as a power amplifier.
Leaving the lens pointed toward the sun could damage the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
12
1 – Introduction
Beware of condensation
If the unit is moved from a cold to a warm place, or used after a sudden
temperature change, condensation could occur. To prevent this, or if this
occurs, let the unit sit for one or two hours at the new room temperature
before using it. In particular, using the camera lens to record or take still
pictures while condensation remains could degrade the quality of the image.
Cleaning the unit
Use a dry soft cloth to wipe the unit clean. Do not clean the unit with a
chemically treated cloth or substances such as thinner or alcohol. Doing so
could damage the surface or change the color of the unit.
Cleaning the lens
If the lens is dirtied by fingerprints or oil, for example, use a soft cloth or
photographic lens tissues to wipe its surface clean.
User registration
See the end of this manual for details about user registration.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
13
2 – Names and Functions of Parts
3
F1(
) button
Top panel
Press and hold this button to turn the unit’s power ON or OFF.
This button’s function when pressed momentarily changes depending
on what is shown on the display. The current function is shown at the
bottom of the display just above the button. (See “Basic operation”on
page 27.)
4
MENU button
When the Home Screen is open, press this button to open the MENU
Screen.
Press this button to return to the MENUScreen from the various setting
screens.
When the MENUScreen is open, press this button to return to the Home
Screen.
5
6
Zoom control
When in video recording or photo mode, use this when in recording
standby to adjust the digital zoom. Press toward W [m] to zoom out
and toward T [,] to zoom in.
During video or audio playback, press toward W [m] to search
backward, or toward T [,] to search forward.
MODE button
When stopped, press this button to change the operating mode.
Video mode
Audio mode Photo mode
1
2
Built-in stereo microphone
NOTE
This is a cardioid stereo electret condenser microphone. To use this mic
as the input source, set INPUT SELECTto MICon the Input
Settingscreen. When an external microphone or line input is
connected to the MIC/LINE IN jack on the right side panel, however, this
built-in mic is disabled.
Only files supported by the operating mode selected using this button will be
displayed on the BROWSEor PLAYLISTscreen.
The following file formats can be used for recording/playback, according to
the mode.
Video mode:
Audio mode:
Photo mode:
.mov
.wav
.jpg
Display
This 2.4-inch TFT color LCD display has a resolution of 240x320 and
shows video images, still images and a variety of information.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
14
2 – Names and Functions of Parts
7
DISPLAY button
q
w
F3/HOME button
Press this button to hide information on the screen and show only the
image. Press this button again to show the information again.
When the DIMMERitem on the Setupscreen is set to ALL OFF, press
this button to illuminate the display for a few seconds. Indicators will
only light if the normal conditions that cause them to light are met (for
example, the REC indicator appears only during recording).
This button’s function changes depending on what is shown on the
display. The current function is shown at the bottom of the display just
above the button. (See “Basic operation”on page 27.)
When any setting screen is open, press this button to return to the Home
Screen.
RECORD [0] button
8
Pointing Stick
Press when stopped to start recording (video/audio/photo) standby.
Press during recording standby when in video or audio recording mode
to start recording. The REC indicator lights when recording. Press when
recording (video/audio) to pause recording.
Press the center to confirm a selection on a setting screen.
When a setting screen is open, press up (5) to move the cursor up on
the screen.
When the Home Screen is open, press up (5) to raise the output
volume.
When in recording standby in photo mode, press this button to take a
still photo.
When a setting screen is open, press down (b) to move the cursor down
on the screen.
When the Home Screen is open, press down (b) to lower the volume.
When a setting screen is open, press left (g) to move the cursor left on
the screen.
When playing or stopped in the middle of a song/video, press left (g) to
return to the beginning of the song/video.
When stopped at the beginning of a song/video, press left (g) to skip to
the beginning of the previous file.
e
PLAY [t] button
When the Home Screen is open and playback is stopped, press this
button to start playback.
In photo mode, press this button to start a slide show.
When paused, press this button to resume playback from the paused
point.
In photo mode, press this button to start a slide show.
When the unit is stopped, paused or playing back, press and hold this
button to open the BROWSEscreen or a playlist screen, whichever was
open last.
On the BROWSEScreen, press left (g) to move up a level.
When a setting screen is open, press right (t) to move the cursor right
on the screen.
r
STOP/PAUSE [8] button
During playback or when stopped, press right (t) to skip to the next file.
On the BROWSEScreen, press right (t) to open a folder.
Press this button during playback to pause playback.
When playback is paused, press this button to return to the beginning of
the file and stop playback.
Press this button during recording standby (video, audio or photo) to
enable recording standby for the current mode.
Press this button during recording standby (video or audio) to end
recording standby.
9
0
PEAK indicator
This lights red when recording when the audio volume level reaches
-2dB, which is just before it becomes too high and clips).
F2 button
This button’s function changes depending on what is shown on the
display. The current function is shown at the bottom of the display just
above the button. (See “Basic operation”on page 27.)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
15
2 – Names and Functions of Parts
Rear panel
Left side panel
u
microSD card slot
Insert a microSD into this slot. (See “Inserting and removing microSD
cards”on page 32.)
t
Hole for strap
Attach a strap here.
y
Tripod mounting thread (1/4-inch)
Use this to attach the recorder to a tripod.
i
USB port
Use the included USB cable to connect the unit to a computer. (See “9 –
Connecting with a computer”on page 77.)
CAUTION
CAUTION
•
•
•
Tighten the unit securely to the tripod to prevent it from falling off.
Place the tripod on a level surface when using it with this unit.
As some tripods use different types of screw threads, it might not be
possible to attach the unit directly. In such a case, use a commercially
available adaptor.
•
The unit should be connected directly to the computer. Do not use a USB
hub between the unit and the computer.
•
The unit cannot receive bus power from a USB connection, meaning that
the batteries will be used even when you connect the unit to a USB port.
•
If the tripod screw is longer than standard, you might not be able to
attach the unit to the tripod securely. In such a case, use a washer or
other type of spacer between the unit and the tripod mount to attach it
securely.
o
mini-HDMI PORT (Type C)
Use a mini-HDMI PORT (Type C) cable (sold separately) to connect this port
with a television, for example, and output video playback. You can use this
to enjoy higher image and sound quality on an HDMI-compatible TV.
CAUTION
If the audio bit-length of the playback file is 24-bit, the sound will be
converted to 16-bit when output from the HDMI connector.
NOTE
When the unit is set to SD-VGA, icons and information are shown at full size
on the screen, but when set to HD-720p, they are shown smaller at the top left
of the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
16
2 – Names and Functions of Parts
Right side panel
Bottom Panel
p
DC IN 5V jack
Connect a TASCAM PS-P520 AC adaptor (sold separately) here.
a
s
d
INPUT level control
Turn to adjust the input signal levels of the built-in mic and MIC/LINE
IN jack.
/LINE OUT jack
Connect headphones or the line input jack of an amp or other
equipment.
MIC/LINE IN jack
Use this stereo mini-jack (3.5 mm) to connect an external mic or other
external line level device.
This jack supports plug-in power microphones. Use the PLUG IN POWER
item on the Input Settingscreen to enable this.
f
REC indicator
This indicator lights when recording (video and audio). When using the
self-timer, it blinks during the countdown.
g
h
Lens
Mono speaker
Use this built-in speaker to listen to recordings.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
17
2 – Names and Functions of Parts
j
SPEAKER switch
Set this to ON to output sound from the built-in speaker.
Even when ON, no sound will be output in the following situations.
Home Screen
•
•
When recording and in recording standby (video/audio)
When headphones or another device is connected to the /LINE
OUT port
Video and Audio modes
Appearance during playback and when stopped
8
k
HOLD switch
Setting this switch in the direction of the arrow, enables the hold
function that prevents accidental operation. In this state, all other
buttons are disabled.
l
;
Battery compartment cover
Battery compartment
Install batteries (3 AA) in this compartment to power the unit. (See “Using
AA batteries”on page 29.)
1
2
Operating mode
This icon shows the current operating mode.
0030098
Serial No.
: Video mode
: Audio mode
: Photo mode
File format/sampling frequency of current file
This shows the file format and sampling frequency of the currently active
file.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
18
2 – Names and Functions of Parts
3
Image resolution indicator
6
Operation indicator
This shows the image resolution.
This icon shows the operation status
: Stopped
Indicator
None
0.3M
0.9M
SD-VGA
HD-720p
Meaning
Audio mode, no captured still photo
Audio mode with 640x480 captured still photo
Audio mode with 1280x720 captured still photo
Video mode at SD resolution
: Paused
: Playing back
: Searching forward
: Searching backward
Video mode at HD resolution
7
IN-OUT loop playback/repeat playback/divide mode setting
indicator
4
5
Playback speed setting
Shows the current playback speed (0.5–1.5).
Examples : SPEED 0.5
None : No repeat or loop function active
SPEED 1.5
: Repeat playback ON
Selected area is played back repeatedly.
: Single repeat playback ON
Selected file is played back repeatedly.
: IN/OUT loop playback ON
Area between IN (start) and OUT (end) points are played
back repeatedly in a loop.
Power supply status
A battery icon appears when the unit is powered by batteries.
When batteries are being used, the icon shows the amount of power
remaining in bars(
,
,
).
When the icon starts flashing, the batteries are almost dead and the
power will turn off soon. If the icon starts flashing during recording
(audio/video), the unit will end recording and power off.
: Divide mode
Only selected file is played back repeatedly.
When the unit is being powered by a TASCAM PS-P520 AC adaptor (sold
separately),
will be displayed.
NOTE
Sometimes a Battery empty warning appears when recording (audio/video)
or conducting other demanding operations even when some battery power
still remains.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
19
2 – Names and Functions of Parts
8
Elapsed time
r
File information display
This shows the elapsed time (hours: minutes: seconds) of the file being
played.
Shows the name of the currently playing file.
NOTE
9
0
q
Playback position display
This bar shows the current playback position. As playback progresses, the
bar extends from left to right.
File names in Japanese and other languages that use multibyte encodings
cannot be shown correctly.
t
F2 button function
Playback file number/Total number of files
This shows the total number of files in the selected playback area and the
number of the current file.
This shows the function currently assigned to the F2 button.
DELETE : Use to open the FILE DELETEpop-up to confirm file
deletion. (See “Deleting the selected file”on page 73.)
Playback area display
This shows the current playback file area.
y
F3/HOME button function
This shows the function currently assigned to the F3/HOME button.
SPEED : Use to open the SPEED CONTROLpop-up where you can
adjust the playback speed. (See “Setting the playback speed
(method 1)”on page 72.)
ALL
FOLDER : All files in the selected folder (including files in sub-folders)
P.LIST : All files added to the playlist
: All files on the microSD card
w
IN-OUT loop playback points
These icons show the loop playback starting (IN) and ending (OUT)
points.
When the starting point is set, the
icon appears at the corresponding
point beneath the playback position bar.
When the ending point is set, the
icon appears at the corresponding
point beneath the playback position bar.
In divide mode, the loop starting/ icons disappear, and the icon
appears at the current position.
e
F1(
) button function
This shows the function currently assigned to the F1(
(YES).
) button
I/O LOOP : Use to open the I/O LOOP SETTINGpop-up to set
IN/OUT points. (See “Looping playback”on page 71.)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
20
2 – Names and Functions of Parts
3
Image resolution indicator
Appearance during recording (audio/video)
8
None
0.3M
0.9M
Audio mode, no captured still photo
Audio mode with 640x480 captured still photo
Audio mode with 1280x720 captured still photo
The display appears as follows when in recording standby or recording.
SD-VGA Video mode at SD resolution
HD-720p Video mode at HD resolution
4
5
Digital zoom indicator
Shows the current digital zoom level. Nothing is shown when zoom is
not in use.
Example:
: Current digital zoom magnification is 1.2 times normal
White balance setting
The icon shows the current white balance setting. Power supply status
Icon Setting
Description
AUTO (default) Adjusts automatically according to the
situation
Use for white bulb lighting
1
2
Operating mode
This icon shows the current operating mode.
BLUB LIGHT
FL LIGHT
Use for daytime white fluorescent lighting
: Video mode
STAGE LIGHT Use for stage and similar lighting
: Audio mode
SUNLIGHT
CLOUDY
Use outdoors in clear weather
Use outdoors in cloudy weather
File format/sampling frequency used for recording
This shows the file format and sampling frequency used for recording
(video/audio).
6
7
Power supply status
This icon shows the power supply status. See “5 Power supply status”on
page 19 for details.
Level meters/peak indicators
When input monitoring is OFF, these show the playback volume level.
When the file being played or recorded is stereo, two meters are shown
with L (left) and R (right) labels below them. When the file is mono, only
one meter is shown and it is labeled MONO.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
21
2 – Names and Functions of Parts
8
Recorder operation indicator
This icon shows the recorder operation status.
t
y
Elapsed time
Shows the elapsed time (hours: minutes: seconds) of the recording
(video/audio).
: Recording (video/audio) standby
Remaining recording (video/audio) time
Shows the remaining recording time (hours: minutes: seconds) on the
loaded microSD card for the current recording format.
: Recording (video/audio)
9
0
q
w
e
Auto-record function status
NOTE
The
icon appears when auto-recording (video/audio) is ON and
the unit is recording or in recording standby.
The remaining time is an approximate estimate and differs from the actual
available recording (video/audio) time. In particular, since the compression
ratio changes depending on video recording conditions, recorded file sizes
may vary greatly.
Pre-recording function status
The
icon appears when pre-recording (video/audio) is ON and the
unit is recording or in recording standby.
u
F1(
) button function
Peak value in decibels (dB)
Shows the maximum recording input level in decibels at regular
intervals.
This shows the function currently assigned to the F1(
No indicator :
) button.
In recording standby in video mode, the F1(
)
Low cut filter function status
Shows whether or not a low cut filter is in use. A
when the filter is set to 40Hz, 80Hz or 120Hz.
button has no function.
DIVIDE
: Divides the currently recording (video/audio) file. This
appears only when recording.
: Captures a still photo. Saves a JPEG file with the same
name as the audio recording file. This appears only
when in audio mode recording standby.
icon appears
CAPTURE
Self-timer function status
Shows whether or not the self-timer is ON. An icon appears when ON.
No indicator
:
:
:
Self-timer function OFF
i
File information display
Shows the name that will be automatically assigned to a recording file
(video/audio).
Self-timer function ON (set 2 seconds)
Self-timer function ON (set 10 seconds)
NOTE
r
Level control function status
File names in Japanese and other languages that use multibyte encodings
cannot be shown correctly.
Shows whether or not level control or limiter is in use.
No indicator : Auto level control/limiter is OFF
: Auto level control is ON
: Limiter is ON
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
22
2 – Names and Functions of Parts
o
p
F2 button function
Photo mode
This shows the function currently assigned to the F2 button.
INPUT SETTING : Use to open the Input Settingscreen. (See
“Preparing the recording inputs”on page 38.)
Appearance during playback and when stopped (Slide
show)
8
F3/HOME button function
This shows the function currently assigned to the F3/HOME button.
REC SETTING : Use to open the REC OPTIONscreen.
Photos taken by the unit are shown in a slide show.
NOTE
When in recording (video/audio) standby, REC SETTING appears above the
F3/HOME button, but is not possible to change the AUTO REC MODE
and AUTO REC LEVELitems from this screen.
To change these items, end recording (video/audio) standby and open the
Rec Optionscreen.
1
Operating mode
This icon shows the current operating mode.
: Photo mode
2
3
Playback file image resolution
0.3M : 640 x 480
0.9M : 1280 x 720
Playback area display
This shows the current playback area.
ALL
FOLDER : All files in the selected folder (including files in sub-folders)
P.LIST : All files added to the playlist
: All files on the microSD card
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
23
2 – Names and Functions of Parts
4
Playback file number/total number of files
This shows the current file number and the total number of files in the
current playback area.
Appearance when ready to shoot
8
The image that the camera will capture is shown on the screen in real
time.
5
Power supply status
This icon shows the power supply status. See “5 Power supply status”on
page 19 for details.
6
7
Photo mode slide show status
The
icon shows when a slide show is playing.
Self-timer function status
Shows whether or not the self-timer is ON. An icon appears when ON.
No indicator
:
:
:
Self-timer function OFF
Self-timer function ON (set 2 seconds)
Self-timer function ON (set 10 seconds)
8
9
F1(
) button function
1
2
Operating mode
This icon shows the current operating mode.
This shows the function currently assigned to the F1(
SELF TIMER : Cycles through the self-timer settings.
) button.
: Photo mode
2Sec
10Sec
OFF
Still image resolution
File information
Shows the name of the current file shown.
NOTE
0.3M : 640 x 480
0.9M : 1280 x 720
File names in Japanese and other languages that use multibyte encodings
cannot be shown correctly.
0
F2 button function
This shows the function currently assigned to the F2 button.
DELETE : Use to open the FILE DELETEpop-up and confirm file
deletion. (See “Deleting the selected file”on page 73.)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
24
2 – Names and Functions of Parts
3
4
Digital zoom indicator
Shows the current digital zoom level. Nothing is shown when zoom is
not in use.
Example:
Menu structure
Press the MENU button to open the MENUscreen.
: Current digital zoom magnification is 1.2 times normal
White balance setting
The icon shows the current white balance setting.
Icon Setting
Description
AUTO (default) Adjusts automatically according to the situation
BLUB LIGHT
FL LIGHT
Use for white bulb lighting
Use for daytime white fluorescent lighting
Use for stage and similar lighting
Use outdoors in clear weather
Use outdoors in cloudy weather
The menu contains the following items.
STAGE LIGHT
SUNLIGHT
CLOUDY
Menu item
Function
Reference
INPUT
Input settings
Page 38
Recording (video/audio) mode
settings
Playback area, repeat playback and
other settings
Playback speed change and other
special playback
Recording (video/audio) quality
settings
REC OPTION
PLAY
Page 46, 48, 49, 50
Page 62, 69, 70, 75
Page 72, 73
5
6
Power supply status
This icon shows the power supply status. See “5 Power supply status”on
page 19 for details.
PB CONTROL
REC QUALITY
Self-timer function status
Shows whether or not the self-timer is ON. An icon appears when ON.
Page 36
No indicator
:
:
:
Self-timer function OFF
Page 31, 79, 81, 82,
83, 84
Page 61, 65
SETUP
System settings
Self-timer function ON (set 2 seconds)
PLAYLIST
BROWSE
Playlist editing
microSD card file and folder
operations
Self-timer function ON (set 10 seconds)
Page 56
7
F1(
) button function
This shows the function currently assigned to the F1(
SELF TIMER : Cycles through the self-timer settings.
) button.
2Sec
10Sec
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
25
2 – Names and Functions of Parts
Using menus
The following example explains how to change the playback area.
1. Press the MENU button to open the MENUscreen.
PLAY AREAselected on the Play Optionscreen
4. Press t or press the center of the Pointing Stick to open the setting
options pop-up. (The current setting has an orange background.)
2. Use the Pointing Stick to select a menu item and press the center to open
the selected settings screen. (The selected item has an orange frame.)
5. Press 5 and b to change the setting.
PLAY menu selected
3. Press 5 and b to select the item that you want to set. (The selected
item has an orange background.)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
26
2 – Names and Functions of Parts
6. To set another item on the same menu, press the center of the Pointing
Stick to confirm the setting. Then, press 5 and b to move up and
down and select a new item for setting. (The selected item has an orange
background.)
Basic operation
Use the following buttons to operate the various setting screens.
7. Repeat steps 3 to 6 as necessary to set other items.
MENU button
8. When a setting item is selected (orange background), press g or press
the MENU button to return to the MENUscreen.
Opens the MENUscreen.
Press the F3/HOME button to return to the Home Screen.
Operation mode button
Changes the operation mode.
NOTE
•
On the MENUscreen, press the MENU button to return to the Home
F3/HOME button
Screen.
When a setting screen is open, press this button to return to the Home
Screen.
Press this to answer [NO] to a confirmation message.
On the Home Screen, you can use it as the F3/HOME button.
•
The first time the MENUscreen is opened, INPUT is selected (orange
frame). The next time the MENUscreen is opened, however, the last
selected item will still be selected.
•
The first time a setting screen is opened, the top item is selected (orange
background). The next time the setting screen is opened, however, the
last selected item will still be selected.
When a setting selection pop-up is opened, the current value is selected
(orange background).
Pointing Stick
On the MENUscreen, press the center of the Pointing Stick to open the
selected setting screen.
Press the center of the Pointing Stick to confirm the selection of a setting
item.
Press t to move right on a setting screen (current selection is orange)
and to open a folder on the BROWSEscreen.
•
•
When more than 7 items are available,
and/or
appear indicating
that there are hidden items in the direction of the arrow.
Press g to move left on a setting screen (current selection is orange) and
to close a folder on the BROWSEscreen.
On a menu setting item selection screen, press g or the center of the
Pointing Stick to open the setting screen.
On a setting screen, press the center or g to return to the MENUscreen.
Press 5 and b to select an item (highlighted) or adjust a value.
On the Home Screen, press 5 and b to adjust the output level. (Press
5 to raise the volume, and b to lower it.)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
27
2 – Names and Functions of Parts
Function buttons (F1–F3)
Depending on the operating mode, different functions are assigned to
these buttons.
Mode
F1
F2
F3
Stopped
Playback
Recording
standby
Recording
Stopped
Playback
I/O LOOP
DELETE
SPEED
Video
—
DIVIDE
INPUT SETTING REC SETTING
DELETE SPEED
I/O LOOP
CAPTURE /
RECAPTURE*
DIVIDE
Audio
Photo
Recording
standby
INPUT SETTING REC SETTING
INPUT SETTING REC SETTING
Recording
Stopped
Playback
Recording
standby
Recording
I/O LOOP
SETTING
SELF TIMER
DELETE
—
SELF TIMER
—
—
—
—
—
IN
OUT
CLOSE
FILE DELETE YES
—
—
—
NO
NO
NO
Home
Screen
Pop-ups
FORMAT
INITIALIZE
SPEED
YES
YES
ON/OFF
—
CLOSE
HOME
HOME
CONTROL
THUMBNAIL /
FILE
THUMBNAIL /
BROWSE
PLAYLIST
PLAYLIST
BROWSE
Other
screen
FILE
*Capture and recapture are only available in audio mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
28
3 – Preparation
•
Remove batteries from the compartment when not using the unit for
long periods of time. Batteries left in the compartment might discharge
gradually, rupture or leak fluid, which could result in damage to the unit.
Powering the unit
Power supply options
Use three AA batteries or a TASCAM PS-P520 AC adapter (sold separately) to
power the unit.
Using an AC adaptor (sold separately)
Connect a TASCAM PS-P520 AC adapter (sold separately) to the DC IN 5V jack
as shown in the illustration.
Either alkaline or Ni-MH batteries can be used.
Using AA batteries
Open the battery compartment cover on the bottom of the unit. Insert three
AA batteries oriented according to the ¥/^ marks in the compartment, and
close the battery compartment cover.
AC wall socket
TACAM
PS-P520 (sold separately)
DC plug
CAUTION
Never use any AC adapter other than the designated TASCAM PS-520 AC
adapter. Use of a different adaptor could cause malfunction, fire or electric
shock.
When using AA batteries, set the type of battery. This allows the unit to
show the amount of power remaining accurately, and to determine whether
enough power is available for proper operation. (See “Setting the battery
type”on page 81.)
NOTE
When batteries are installed and the AC adaptor is connected, power will be
supplied by the AC adaptor.
CAUTION
•
•
Manganese dry cell batteries (R6) cannot be used with this unit.
This unit cannot recharge Ni-MH batteries. Use a commercially available
recharger.
•
The included alkaline batteries are only for confirming the operation of
the unit. For this reason, they may run out of charge quickly.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
29
3– Preparation
Turning the power ON and OFF
CAUTION
Before turning this unit’s power ON, turn the volume down all the way on any
connected monitoring equipment. If you are wearing connected headphones,
remove them before turning the power ON or OFF. Failure to do the above
could result in noise that damages speakers and harms hearing.
Turning the power ON
Home Screen with file loaded
When the unit is turned OFF, press and hold the F1(
) button until the
If there is no file, a message appears on the display, depending on the mode:
“No Movie File”in video mode, “No Audio File”in audio mode, or “No Photo
File”in photo mode.
PEAK indicator right of the display lights.
“TASCAM DR-V1HD Startup…”appears while the unit starts up, and then the
Home Screen opens.
The settings and the file last used are automatically loaded.
Home Screen without video file
NOTE
•
Start-up screen
The first time the power is turned ON, the Date/Time screen where you
can set the date and time will open before the start-up screen. This also
happens if the unit has been left without power for some time and the
internal clock has reset. (See “Setting the date and time”on page 31.)
•
If the power is turned ON when the remaining battery charge is very
low, the unit might not start up properly and function incorrectly. If
this occurs, install batteries that are new or have a sufficient charge and
restart the recorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
30
3 –Preparation
Turning power off (standby)
To turn the unit off, press and hold the F1(
Setting the date and time
) button until HD VIDEO
LINEAR PCM RECORDER Shutdown… appears and then release the button.
After the shutdown process completes, the unit turns off.
This unit uses its internal clock to make a record of the date and time when a
file (video/audio/photo) is recorded.
1. Press the MENU button to open the MENUscreen.
CAUTION
Always use the F1(
2. Use the Pointing Stick to select SETUPand press the center of the
) button to turn the unit OFF. Do not remove the
Pointing Stick to open the Setupscreen.
batteries or disconnect the TASCAM PS-P520 AC adapter while the unit is
operating. If you do so, all recordings (audio, video and photo), settings and
other data will be lost. Data and settings that are lost cannot be recovered.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
31
3– Preparation
3. Press 5 and b to select DATE/TIME and press t to open the DATE/
Inserting and removing microSD cards
TIME Screen.
Inserting the card
NOTE
A microSD card is already installed when the unit is shipped from the factory.
If you want to use this microSD card to record and play video and audio and
take and view photos, there is no need to reinstall it.
1. Open the microSD slot cover on the left side panel of the unit.
2. Insert the microSD Card into the slot as shown in the following
illustration until it clicks into place.
4. Press g and t to move between units.
Press 5 and b to change the values.
5. Press the F1(
) button (SET) to confirm the changes and return to
the Setupscreen.
Press the F3/HOME button (CANCEL) to cancel the changes and return to
the Setupscreen.
6. When done changing the setting, press the F3/HOME button to return to
the Home Screen.
NOTE
You can set the unit to automatically add this date and time to file names.
(See “Setting the format of file names”on page 82.)
CAUTION
The date and time setting is only retained for a few minutes if the unit is not
powered by batteries or a TASCAM PS-P520 AC adaptor (sold separately).
When using batteries, replace them before they completely lose power.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
32
3 –Preparation
Removing the card
1. Open the microSD slot cover on the right side panel.
Preparing a microSD card for use
In order to use a microSD card with this unit, you must first format it with the
unit.
2. Press the microSD card in gently and then release it to allow it to come
out.
CAUTION
CAUTION
Do not remove the microSD card from the unit when it is connected to a
computer via USB.
Formatting deletes all the data on a card.
1. Confirm that a microSD card is inserted in the unit, and turn the power
ON.
NOTES
2. The following pop-up message appears when a new card or a card
formatted for use with another device is installed in the unit.
•
microSD cards that meet microSD or microSDHC standards can be used
with this unit.
•
A list of microSD cards that have been confirmed to work with this unit
can be found on our website (http://tascam.com/).
3. Press the F1(
) button (Yes) to start formatting the card.
Press the F3/HOME button (No) to cancel formatting. If you cancel
formatting, you will need to remove the card and use a different one.
4. When formatting completes, the Home Screen will open.
CAUTION
When formatting a card, make sure the unit is powered by a TASCAM PS-P520
AC adapter (sold separately) or that the batteries have sufficient remaining
power.
NOTE
You can format a card at any time. (See “Formatting”on page 83.)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
33
3– Preparation
Using the built-in speaker
Connecting monitors and headphones
Set the SPEAKER switch on the bottom panel to ON to listen to playback with
the built-in speaker.
To listen with headphones or an external monitoring system (powered
monitor speakers or an amplifier and speakers), connect them to the /LINE
OUT jack.
Powered monitor speakers
or ampliꢀer and speakers
Headphones
NOTE
When set to ON, sound will usually be output from the built-in speaker. In the
following cases, however, sound will not be output even when set to ON.
•
•
When recording and in recording standby (video/audio)
When headphones or another device is connected to the /LINE OUT
port
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
34
3 –Preparation
Setting the operating mode
Set the operating mode that you want to use for recording or playback.
To change the mode, press the operation mode button when the unit is
stopped.
Audio mode Photo mode
Video mode
Video mode
Use this mode for recording and playing video.
Audio mode
Use this mode for recording and playing audio.
Photo mode
Use this mode to take and view still photos.
NOTE
The unit remembers the selected operating mode and the last used mode will
be active the unit is restarted.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
35
4 – Video/Audio Recording
You can use the built-in camera to record video and the built-in microphone
to record audio. In addition to using the built-in microphone, you can record
using an external microphone or record audio output from a CD player or
other external device.
The MOV format is the only video recording format supported. (Video with
96kHz audio is not supported.). You can set the image resolution to SD (640 x
480) or HD (1024 x 720).
The file format used for audio recording is WAV. You can set the sampling
frequency to 44.1, 48 or 96 kHz and the bit rate to 16 or 24.
In addition, with this recorder, while playing back a recorded video file you
can overwrite the playback sound with the input sound and record it as a new
file (After Rec function).
3. Press 5 and b to select SOUND FORMAT, and then press t or the
center of the Pointing Stick.
Set the audio recording bit rate here.
Press 5 and b to select one of the following.
Options : WAV 16bit (default), WAV 24bit
4. Press the center of the Pointing Stick to confirm the setting change and
return to the setting item list.
Setting the operating mode
Set the operating mode to either video or audio as appropriate. (See “Setting
the operating mode”on page 35.)
Use Video mode to record video (with audio) or Audio mode to record audio
only.
5. Press 5 and b to select SAMPLE RATE, and then press t or the center
of the Pointing Stick.
Setting the audio file recording format, sampling
frequency and video image resolution
Before you start recording (video/audio), select the recording file format.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the REC QUALITYmenu and press
Set the sampling frequency here.
Press 5 and b to select one of the following.
Options : 44.1kHz (default), 48kHz, 96kHz.
the center of the Pointing Stick to open the REC QUALITYscreen.
CAUTION
In video recording mode, is not possible to record when set to 96kHz. An
“Unsupported Sampling Rate!!”pop-up message will appear.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
36
4 – Video/Audio Recording
6. Press the center of the Pointing Stick to confirm the setting change and
return to the setting item list.
7. Press 5 and b to select IMAGE SIZE, and then press t or the
Available recording time indicator
The available recording (video/audio) time differs depending on the microSD
card capacity, bit rate, sampling frequency and recording mode (video/audio).
center of the Pointing Stick.
This shows the estimated recording time remaining on the microSD card.
(See “Recording durations”on page 53.)
Available recording time
on the microSD card
Set the screen resolution here.
Press 5 and b to select one of the following.
Options : HD/0.9M (default) and SD/0.3M.
8. Press the center of the Pointing Stick to confirm the setting change and
return to the setting item list.
Set where to save files
9. When setting is complete, press the F3/HOME button to return to the
Select the folder where recorded files (video/audio) will be stored.
New recording files are stored in the folder set as the current folder. Set the
Home Screen.
current folder on the BROWSEscreen. (See “Folder operations”on page 60.)
The default current folder is “MY_FOLDER”. If you do not change the default
folder, newly recorded files will be saved in “MY_FOLDER”.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
37
4 – Video/Audio Recording
recording live performances and other situations when volume changes
are extreme.
When LIMITER mode is active, the recording level can still be adjusted
manually.
Preparing the recording inputs
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select INPUT, and press the center to button to
LOW CUT:
open the Input Settingscreen.
Set the low cut filter cutoff frequency for microphone input to avoid
recording sounds such as air conditioner rumble, etc.
Options: OFF (default), 40Hz, 80Hz, 120Hz
INPUT SELECT:
Set whether the input source is a microphone (MIC) or line level signal
(LINE). The default setting is MIC.
Regardless of the setting, the built-in microphone automatically
becomes the input source when nothing is connected to the MIC/LINE
IN stereo mini jack.
Set this to MIC to use an external microphone connected to the MIC/
LINE IN stereo mini jack.
Set this to LINE to use a line level external device connected to the MIC/
LINE IN stereo mini jack.
When set to LINE, the PLUG IN POWER item will automatically be
disregarded.
This screen contains the following setting items.
Use the Pointing Stick to set each item.
MIC GAIN:
Set the microphone input sensitivity. When the input level is low, set to
MID or HIGH.
Options: LOW (default), MID, HIGH
LEVEL CONTROL:
When recording through the built-in microphone, you can use one of
two level control functions.
Options: OFF (default), AUTO, LIMITER
When set to AUTO (automatic gain control mode), the unit’s input gain
changes automatically in response to the input level, so loud sounds are
made quieter and soft sounds are made louder, making the recording
level as even as possible. This is useful for recording meetings, for
example.
When AUTO mode is active, the recording level cannot be adjusted
manually.
When set to LIMITER (limiter mode) the unit’s input gain is lowered
automatically to prevent loud sounds from distorting. This is useful for
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
38
4 – Video/Audio Recording
•
When recording a live performance or other situation when extremely
loud signals might be input, set LEVEL CONTROL to LIMITER to prevent
sound distortion due to sudden high levels.
PLUG-IN POWER:
Set this to ON when connecting a microphone that requires plug-in
power. Set this to OFF when using the built-in microphone.
Options: ON, OFF (default)
When the INPUT SELECTitem is set to LINE, plug-in power will be
disabled regardless of the PLUG IN POWER item setting. When set to MIC,
the PLUG IN POWER item setting will be used.
L/R SWAP:
Set to R-L to switch the left (L) and right (R) channels of the built-in
microphone.
Options: L-R (default), R-L
INPUT TYPE:
Set to STEREO or MONO according to the type of mic being used.
Options: STEREO (default), MONO
When set to MONO, both left and right channels receive the same input
signal.
NOTE
When in recording (video/audio) standby, you can also press the F2 button
(INPUT SETTING) to open the Input Settingscreen.
CAUTIONS
•
•
•
If the input signal is too loud, distortion might occur even when the
LIMITER is ON. If this occurs, lower the recording level manually or move
the recorder further from the sound source.
When connecting a dynamic microphone or a microphone with a built-
in battery, set PLUG-IN POWER to OFF. Leaving it ON might damage the
microphone.
Use headphones to monitor when you are recording with a microphone.
If you use speakers to monitor, the sound output from the speakers
might also be recorded, causing a poor recording or feedback.
TIPS
If air-conditioning, wind or other noises are being recorded, setting LOW
CUT to a value other than OFF might reduce the noise.
•
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
39
4 – Video/Audio Recording
NOTE
Placement when recording with the built-in mic
Supported microphone types
•
•
•
Dynamic mics
Mics with built-in batteries
Electret condenser mics that support plug in power
Point the lens at the subject, and place the unit in a stable location where
there is little vibration.
Connecting an external mic or device
Recording with an external microphone (MIC IN)
Connect an external microphone to the MIC/LINE IN jack.
Point the unit’s lens at the subject and the external microphone at the sound
source, and place the unit and the microphone in a stable location where
there is little vibration.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
40
4 – Video/Audio Recording
Recording with an external device (LINE IN)
Use a stereo mini plug cable to connect the output of an external audio
Adjusting the input level
device to the MIC/LINE IN jack.
The following procedures explain how to adjust the input level.
1. Press the RECORD button to put the unit into recording standby (video/
audio). The recording (video/audio) screen appears.
The
icon shows the recording standby status.
2. Use the INPUT volume dial on the right side panel to adjust the input
level.
Audio device /
external audio source
The PEAK indicator to the right of the display lights red just before the
recording volume level becomes too high. Adjust the recording level so
that the PEAK indicator light does not turn red.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
41
4 – Video/Audio Recording
When using the built-in microphone or external microphone as the input
source (INPUT SELECTset to MIC on the Input Setting
screen), if the signal level is still low even when the input level is set to
the maximum, set MIC GAIN on the Input Settingscreen to a
higher value. (See “Preparing the recording inputs”on page 38.)
TIPS
•
In addition to adjusting the INPUT volume dial, try changing the
distance and angle between the microphone and the sound source. The
orientation and distance of the microphone relative to the sound source
will change the character of the recorded sound.
CAUTION
•
You can also use the auto gain control or limiter function to prevent
distortion if the input signal becomes too high during recording. (See
“Preparing the recording inputs”on page 38.)
•
•
Observe the following precautions when recording with a microphone:
If MIC GAIN is set to MID or HIGH on the Input Settingscreen,
the sound being recorded might be distorted even if the PEAK indicator
does not light.
•
•
When adjusting the input level, first set MIC GAIN to LOW on the
Input Settingscreen and then adjust the INPUT volume dial. If a
suitable input level is not achieved even if the INPUT volume dial is set to
the maximum, set MIC GAIN to MID. If you still cannot achieve a suitable
input level, set MIC GAIN to HIGH.
If the input level is too high, the sound being recorded might be
distorted even if the Limiter is ON. If this occurs, lower the INPUT level
manually or move the mic further from the sound source.
NOTE
•
•
To exit recording standby (video/audio), press the STOP/PAUSE button.
When INPUT SELECTis set to LINE on the Input Setting
screen, the GAIN setting is disabled.
•
When in recording standby or during recording (video/audio), no sound
will be output from the speaker even if the SPEAKER switch is set to ON.
If you want to monitor the input while adjusting the level or recording,
connect headphones to the /LINE OUT jack. You can adjust the
monitoring volume by pressing 5 and b when the Home Screen is
open. This does not affect the level of the recorded signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
42
4 – Video/Audio Recording
2. Press the RECORD button again to start ordinary recording (video/
audio).
Recording (video/audio)
When recording starts, the REC indicator lights, and the elapsed
recording time and remaining recording time appear on the screen.
In Video mode, the video that is being recorded also appears on the
screen.
In Audio mode, the captured image (if there is one) appears on the
screen. Otherwise, the image shown below appears on the screen.
The following procedure describes how to set the input level after the input
source is set and the Home Screen is already open.
1. Press the RECORD button to put the unit into recording standby (video/
audio). On the recording (video/audio) screen, various information
including the operation mode, recording file format and sampling
frequency, image resolution and zoom level appear. So, you can check
them before starting to record.
TIPS
•
During recording standby in audio mode, you can take a photo (capture)
that can be used as a background during recording and playback. (See
“Capturing an image for audio file background”on page 50.)
•
You can change the digital zoom magnification when shooting a movie.
(See “Adjusting camera magnification”on page 44.)
3. To end recording, press the STOP/PAUSE button.
To pause recording, press the RECORD button. Press the RECORD button
again to restart recording in the same file.
If you press the STOP/PAUSE button after pausing recording, a file with
the video or audio recorded up to this point will be created.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
43
4 – Video/Audio Recording
Adjusting camera magnification
Overwriting recorded audio with the input signal
(After Rec)
This unit’s digital zoom allows you to zoom in on a subject before recording or
taking a picture and during video recording.
When in recording standby or during recording, the digital zoom level is
shown at the top right of the Home Screen.
You can adjust the zoom from 100%–400% (x1 to x4 in 0.1 increments).
To adjust the zoom, press the Zoom control towards W [m] or T [,].
While playing back a recorded video file you can overwrite the playback
sound with the input sound and record it as a new file (After Rec function).
NOTE
•
•
After recording can only be used in the video recording mode.
When using after recording, you cannot use the auto-recording function
or start a new file manually.
W [m]
Press the zoom control in this direction during recording or recording
standby to decrease the zoom level and widen the field of view (W :
wide).
•
•
•
During after recording, sound will not be output from the built-in
speaker even if the SPEAKER switch is set to ON.
You cannot pause during after recording (the RECORD button is
disabled).
When using after recording, the sampling frequency of the playback file
is used regardless of the current recording sampling frequency setting.
T [,]
Press the zoom control in this direction during recording or recording
standby to increase the zoom level and narrow the field of view (T :
telephoto).
Selecting the file to overwrite
Use g and t or the BROWSEscreen to select the file.
NOTE
See “6 – Working with files and folders on the BROWSE screen”on page 56 for
how to select a file on the BROWSEscreen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
44
4 – Video/Audio Recording
Using the after recording function
1. Select the file that you want to After Record on the BROWSEscreen.
Dividing a recording while continuing to record
You can manually divide a recording, saving the current file and continuing to
record as a new file (video/audio).
2. Press the center of the Pointing Stick to open the pop-up menu and
select After Rec.
Dividing also occurs automatically when the 2GB maximum file size is
reached.
NOTE
If AUTO REC is set to FILE INC, dividing will also occur whenever recording is
restarted. (See “Automatic recording functions (AUTO REC)”on page 46.)
Manually starting a new file while recording
When recording (video/audio), press F1(
) button (DIVIDE) to divide the
recording, saving the current file and continuing recording in a new file.
3. Press the center of the Pointing Stick again to put the recorder into
recording (video/audio) standby.
4. Press the RECORD button to start after recording.
When recording starts, the REC indicator lights, and the elapsed and
remaining recording times appear on the Home Screen along with the
name of the file being played back.
NOTE
When a new file is created, the number added at the end of the file name is
increased by one.
CAUTION
•
•
•
A new file cannot be created if the total number of files and folders
would exceed 9999.
A recording (video/audio) cannot be divided if the recording time of one
of the new files would be shorter than two seconds.
If the name of a newly created file would be the same as that of an
existing file, the number added at the end of the file name is increased
by one.
NOTE
The input monitoring sound will be heard a little after the actual sound.
5. When after recording completes for the selected file, the recorder will
stop. (To play back the file that was created by after recording, you must
select it by browsing.)
CAUTION
•
When the file is divided manually, a little time is required to process it, so
a gap of about 1 second will occur in sound and video recording. If you
want to divide a file without creating gaps, record one continuous file
and then divided it afterwards (see “Dividing a file (DIVIDE)”on page 51.).
If the operation mode is not video recording mode, After Rec will not appear
in the pop-up menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
45
4 – Video/Audio Recording
Automatic recording division at maximum file size
If the maximum file size of 2GB is reached during recording, the recording is
divided automatically, saving the current file and continuing to record as a
new file.
Automatic recording functions (AUTO REC)
You can set the unit to start, pause and divide recording (video/audio)
automatically in response to the input volume level.
CAUTION
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select REC OPTIONand press the center of
•
A new file cannot be created if the total number of files and folders
would exceed 9999. If this happens, a “File Full”pop-up message appears
on the screen and recording is stopped.
the Pointing Stick to open the REC OPTIONscreen.
•
When the file is divided manually, a little time is required to process it, so
a gap of about 1 second will occur in sound and video recording.
TIP
The same file size could have different possible recording times, depending
on the bit length, sampling frequency and resolution settings. If the recording
length is 24 hours or more, it will be shown as 23:59:59.
3. Press 5 and b to select AUTO REC MODE, and then press t or
the center of the Pointing Stick.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
46
4 – Video/Audio Recording
4. Press 5 and b to set the auto-recording mode.
7. Press 5 and b to set the level used to determine when a signal has
been input.
OFF (default) Recording will not start/pause automatically.
OPTIONS : -6dB, -12dB (default), -24dB, -48dB
PAUSE
Recording starts automatically when the AUTO
REC LEVELsetting value is exceeded, and pauses
automatically when the input signal falls below that
level for more than five seconds. If the AUTO REC
LEVELis exceeded again, recording continues in the
same file.
8. When setting is complete, press the F3/HOME button to return to the
Home Screen.
9. Press the RECORD button to put the unit into recording standby (video/
audio). Recording starts automatically when the input signal exceeds the
AUTO REC LEVELsetting.
Recording stops automatically when the input signal drops below the
AUTO REC LEVELfor more than 5 seconds.
Recording restarts automatically when the input signal exceeds the
AUTO REC LEVEL. Recording continues in the same file if the
AUTO REC MODEis set to PAUSE. Recording is made to a new file if
the AUTO REC MODEis set to FILE INC.
FILE INC
Recording starts automatically when the AUTO
REC LEVELsetting value is exceeded, and pauses
automatically when the input signal falls below that
level for more than five seconds. If the AUTO REC
LEVELis exceeded again, recording continues in a
new file.
10. Press the STOP/PAUSE button to stop recording.
5. Press the center of the Pointing Stick to confirm the setting change and
return to the setting item list.
6. Press 5 and b to select AUTO REC LEVEL, and then press t or
NOTE
When in recording (video/audio) standby, REC SETTING appears above the
F3/HOME button, but is not possible to change the AUTO REC MODE
and AUTO REC LEVELitems from this screen.
the center of the Pointing Stick.
To change these items, end recording (video/audio) standby and open the
Rec Optionscreen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
47
4 – Video/Audio Recording
5. When setting is complete, press the F3/HOME button to return to the
Prerecording a few seconds before recording
starts (PRE REC)
Home Screen.
TIP
By using this in combination with the AUTO REC function, you can record
events without losing the beginnings of sounds.
By using the prerecording function, when the unit is in recording standby
(video/audio) you can automatically capture up to two seconds of the signal
input before the recording starts.
NOTE
If the unit has been in record standby for less than two seconds, sound for the
amount of time in standby is recorded.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select REC OPTIONand press the center of
the Pointing Stick to open the REC OPTIONscreen appears.
3. Press 5 and b to select PRE REC, and then press t or the center of the
Pointing Stick.
4. Press 5 and b to select ON (default: OFF).
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
48
4 – Video/Audio Recording
4. Press 5 and b to select one of the following settings.
Icon Setting Description
Setting the white balance
AUTO (default) Adjusts automatically according to the
situation
You can set the white balance to suit the lighting conditions.
1. Press the MENU button to open the MENUscreen.
BLUB LIGHT
Use for white bulb lighting
2. Use the Pointing Stick to select the REC OPTIONmenu item, and
press the center of the Pointing Stick to open the REC Option
screen.
FL LIGHT
Use for daytime white fluorescent lighting
Use for stage and similar lighting
Use outdoors in clear weather
Use outdoors in cloudy weather
STAGE LIGHT
SUNLIGHT
CLOUDY
3. Press 5 and b to select the WHITE BALANCE item, and then press the
center or t.
White balance icon
The icon for the selected white balance setting appears at the top of the
screen.
5. After completing the setting, press the F3/HOME button to open the
Home Screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
49
4 – Video/Audio Recording
Using the self-timer to delay recording
Capturing an image for audio file background
Use the self-timer to start recording a set amount of time after the RECORD
button is pressed.
In audio mode, you can take (capture) a still photo when in recording standby
and use it as a background during recording/playback.
1. Press the MENU button to open the MENUscreen.
1. Press the RECORD button to put the unit into recording standby.
2. Use the Pointing Stick to select (highlight) REC OPTIONand press
the center of the Pointing Stick to open the REC OPTIONscreen.
3. Press 5 and b to select SELF TIMER, and then press t or the center of
the Pointing Stick.
2. Focus the camera so that the image you want to shoot appears on
screen.
3. Press the F1(
) button (CAPTURE) to take the still photo.
The image captured is saved as a JPEG file with the same name of the
next audio file to be recorded, but with a “.jpg”extension.
4. The captured image is set as the Home Screen background.
4. Press 5 and b to change the setting and then press the center of the
Pointing Stick.
Options: OFF (default), 2 sec, 10 sec.
5. You can press the F1(
) button (RECAPTURE) again to capture
5. When done changing the setting, press the F3/HOME button to return to
a different image, if you want. The previously captured image is
overwritten.
the Home Screen.
NOTE
When the BROWSEscreen is in thumbnail display mode, this image is also
used as the thumbnail.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
50
4 – Video/Audio Recording
4. Press 5 and b to select DIVIDE.
Dividing a file (DIVIDE)
A recorded file can be divided into two at a specified position.
NOTE
The SD card must have at least as much open space as the file being divided.
If there is not enough open space, an “Out of Card Space”pop-up message
appears. If this occurs, change the media or delete unnecessary files to
increase the amount of open space.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select BROWSEand press the center of the
5. Press the center of the Pointing Stick to enter divide mode. The
appears on the Home Screen, and the selected file plays back.
icon
Pointing Stick to open the BROWSEscreen.
Press the F1(
) button (DIVIDE) at the position where you want to
3. Press 5 and b to select the file you want to divide.
divide the file, or press the F3/HOME button (CANCEL). The file will play
back repeatedly until you press one of these buttons.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
51
4 – Video/Audio Recording
NOTE
•
6. Press the F1(
) button (DIVIDE) to open a confirmation pop-up.
In Divide mode, you can use the zoom control (W [m] / T [,]), PLAY
and STOP/PAUSE buttons to quickly search for the position where you
want to divide the file.
•
After dividing a file, two new files with _a or _b added to the end of the
original file name are created. After being divided, the original file is not
automatically deleted.
Example:
File name before dividing
DR0000_0000.wav
File names after dividing
DR0000_0000_a.wav (part before division point)
DR0000_0000_b.wav (part after division point)
7. Press the F1(
) button (YES) again to divide the file, or press the F3/
HOME button (NO) to cancel division.
The
icon disappears from the Home Screen.
CAUTION
•
•
•
The card must have at least as much open space as the file that is
divided.
Division is not possible if the file name would become more than 200
characters long.
Division is not possible if an existing file has the same name as the name
that would be given to a new file created by division.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
52
4 – Video/Audio Recording
Recording durations
The table below shows maximum recording times in hours and minutes on microSD/microSDHC cards of different capacities for different recording bit rates and
sampling frequencies.
microSD/microSDHC card capacity
Operating mode
File recording format settings
2GB
1:01
0:58
0:52
0:50
0:28
0:28
0:26
0:25
3:09
2:53
1:26
2:06
1:55
0:57
4GB
2:00
1:57
1:44
1:40
0:56
0:55
0:52
0:51
6:13
5:47
2:53
4:12
3:51
1:55
8GB
4:01
3:55
3:28
3:21
1:53
1:51
1:45
1:43
12:35
11:34
5:47
8:23
7:43
3:51
16GB
8:03
7:50
6:56
6:42
3:46
3:43
3:30
3:27
25:11
23:08
11:34
16:47
15:25
7:43
32GB
16:07
15:40
13:53
13:24
7:33
7:27
7:01
6:54
50:23
46:17
23:08
33:35
30:51
15:25
44.1kHz
16bit SD-VGA (STEREO)
48kHz
44.1kHz
24bit SD-VGA (STEREO)
48kHz
44.1kHz
16bit HD-720p (STEREO)
48kHz
44.1kHz
24bit HD-720p (STEREO)
48kHz
Video mode
44.1kHz
16-bit WAV (STEREO)
24-bit WAV (STEREO)
48kHz
96 kHz
44.1kHz
48kHz
96 kHz
Audio mode
•
•
The recording times shown above are estimates. These values may differ depending on the microSD/microSDHC card used.
The recording times shown above are not continuous recording times, but rather they are the total possible recording times for the microSD/microSDHC card.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
53
5 – Taking still photos
In addition to using the built-in camera to record video and the built-in
microphone to record audio, you can also take still photos with this unit.
The file format used for still images is JPEG, and the resolution can be set to
0.9M (1280 x 720) or 0.3M (640 x 480).
Set where to save photo files
Select the folder where photo files will be stored.
New photo files are stored in the folder set as the current folder. Set the
current folder on the BROWSEscreen. (See “Folder operations”on page 60.)
Setting the operation mode
The default current folder is “MY_FOLDER”. If you do not change the default
folder, newly recorded files will be saved in “MY_FOLDER”. Only first level
folders can be designated.
Set the operation mode to photo mode to take still photos. (See “Setting the
operating mode”on page 35.)
Setting the image size
Set the image size (resolution) before taking still photos.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select REC QUALITYand press the center
of the Pointing Stick to open the REC QUALITYscreen.
3. Press 5 and b to select IMAGE SIZEand press t or the center of
the Pointing Stick.
4. Press 5 and b to select one of the following size options.
Options : HD/0.9M (default), SD/0.3M.
5. When setting is complete, press the F3/HOME button to return to the
Home Screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
54
5 – Taking still photos
Using the zoom in photo mode
Taking photos
This unit’s digital zoom allows you to zoom in on a subject before taking a
picture.
The procedure below assumes that photo mode is active and the Home
Screen is open.
The digital zoom level is shown at the top right of the Home Screen.
You can adjust the zoom from 100%–400% (×1 to ×4 in 0.1 increments).
Press the zoom control towards W [m] to zoom out or T [,] to zoom in.
1. Press the RECORD or STOP/PAUSE button to put the unit into photo
standby.
The image that the camera will capture is shown on the screen in real
time.
In addition to the photo mode status, the image resolution, digital zoom
level (when zoom in use), white balance mode and current power supply
status are shown on screen.
W [m]
Press the zoom control in this direction during recording or recording
standby to decrease the zoom level and widen the field of view (W :
wide).
At this time, you can use the zoom control to adjust the digital zoom.
2. Press the RECORD button to take a still photo.
For 2 seconds after being taken, the photo is shown without any
information indications.
T [,]
Press the zoom control in this direction during recording or recording
standby to increase the zoom level and narrow the field of view (T :
telephoto).
3. Press the STOP/PAUSE button to exit photo standby.
Using the self-timer in photo mode
Use the self-timer to take a photo a set amount of time after pressing the
RECORD button. This function works the same way as the self-timer of an
ordinary film or digital camera.
On the Home Screen, press the F1(
timer settings.
) button to cycle through the self-
None
(”OFF”)
(”2 sec”)
(”10 sec”)
NOTE
You can also set the self-timer with the Self Timer item on the REC
OPTIONscreen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
55
6 – Working with files and folders on the BROWSE screen
Use the BROWSEscreen to view the contents (including video, audio and
photo files) and delete files, create folders and add files to a playlist. (See
“Playlist”on page 65.)
Setting the operation mode before using the
BROWSE screen
TIP
File operations can only be conducted on files that match the current mode
You can also edit the contents of MY_FOLDER, including deleting files, by
(and the folders that contain them). Set the mode for the type of files that you
accessing the microSD card from a computer. Do this by either connecting
want to work with beforehand. (See “Setting the operating mode”on page
the unit to a computer by USB or by loading the microSD card on the
35.)
computer using a card reader other means. You can also edit file names from
a computer.
Navigating the BROWSE screen
NOTE
File names in Japanese and other languages that use multibyte encodings
In addition to the thumbnail mode, the BROWSEscreen has a file list mode
that shows folders and video, audio and photo files in a hierarchical structure
similar to how they would appear on a computer.
cannot be shown correctly.
To open the BROWSEscreen, press the MENU button to open the MENU
screen. Then, use the Pointing Stick to select BROWSEand press the center
of the Pointing Stick. When the BROWSEscreen opens in thumbnail mode,
it appears as follows.
Press the F1(
) button (THUMBNAIL) to switch between FILE and
THUMBNAIL modes. The selected mode is retained and will be used the next
time the BROWSEScreen is opened.
One level of subfolders can be made and used.
On the BROWSEscreen, the file that was selected on the Home Screen
remains selected and the contents of the folder that contains it are shown.
NOTE
Press and hold the PLAY button when stopped, paused or playing back to
return to the last screen — BROWSEor PLAY LIST
.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
56
6 – Working with files and folders on the BROWSE screen
Select the desired audio file on the BROWSEscreen and press the center of
the Pointing Stick to open the pop-up window shown below.
File thumbnails
File thumbnails are shown according to the mode.
•
•
•
Press 5 and b to select the desired file or folder.
When a folder is selected, press t to open the folder and see its contents.
When a file or folder is selected, press g to close the currently open folder
and view the root folder contents.
Video mode
Playable video files (with .mov extension) are shown. The thumbnail is
a still image from 30 seconds after the playback starting point. If a file
is less than 30 seconds, the final image is displayed as the thumbnail.
To maintain a consistent thumbnail size, black bars are displayed at
the tops and bottoms of thumbnails used for HD videos.
Audio mode
•
While a folder or file is selected, press the center of the Pointing Stick to
open a pop-up menu.
Only audio files with the .wav extension are shown. If the CAPTURE
function was used before recording, the JPEG file with the same name
is shown; otherwise, the icon is shown.
BROWSE screen contents
Photo mode
Still image files with the .jpg extension are shown.
The contents of each display mode are explained in the following sections.
Thumbnail display mode
The following items are shown in thumbnail display mode.
Operation mode
The icon at the upper left corner shows the current operation mode.
Recording starting time
The recording date/time of the currently selected file (starting time for
video or audio) is shown in yyyy/mm/dd hh:mm format.
File name
The name of the currently selected file is shown with an icon for the file
type before it.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
57
6 – Working with files and folders on the BROWSE screen
List mode
Icons shown in list view
The icons shown mean the following.
In FILE list mode, file and folder names are shown with icons.
Video file
This icon, which is shown only in video mode, appears before the names
of video files.
Only playable video files that have the .mov extension are shown.
Audio file
This icon, which is shown only in audio mode, appears before the names
of audio files.
Only audio files with .wav extension are shown.
Photo file
Operation mode
This icon, which is shown only in photo mode, appears before the names
of photo files.
The icon at the upper left corner shows the current operation mode.
Only still image files with the .jpg extension are shown.
Folder name
The name of the currently open folder is shown at the top of the list with
a folder icon.
folder
This icon appears next to folders created inside “MY_FOLDER”on the
microSD card.
File name list
The names of the files in the currently open folder are shown in a list. The
currently selected file is shown with an orange background.
The icons next to the file names show the file type.
Open folder
This icon appears before the name of the folder that is open. The
contents of this folder are shown on this screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
58
6 – Working with files and folders on the BROWSE screen
After Rec
File operations
Put the recorder into recording standby so the audio of the selected
video file can be overwritten.
After Rec can only be used with video files.
Select (highlight) the desired file on the BROWSEscreen and press the
center of the Pointing Stick to open a pop-up menu, as shown below.
Delete
Open a pop-up confirmation, and press the F1(
) button (YES) to
delete the selected file or the F3/HOME button (NO) to cancel deletion.
NOTE
If a deleted file had been added to a playlist, it will also be removed from the
playlist.
Press 5 and b to select the desired menu item and press the center of the
Pointing Stick to use that function.
Cancel
Do nothing with the selected file and close the pop-up menu.
Play
Return to the Home Screen and play back the file. If the playback area
is set to FOLDER, the folder that contains this file becomes the playback
area.
Info
Open a pop-up that shows information (name, format, size, time and
date) about the selected file. Press the F3/HOME button (close) to return
to the BROWSEscreen.
Add List
Add the selected file to a playlist. (See “Playlist”on page 65.)
Divide
Enter divide mode in which you can split the selected file into two. (See
“Dividing a file (DIVIDE)”on page 51.)
Photos cannot be divided.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
59
6 – Working with files and folders on the BROWSE screen
Create
Folder operations
A pop-up message appears to confirm the creation of a new folder.
Select the desired folder on the BROWSEscreen and press the center of the
Pointing Stick to open the pop-up window shown below.
Press the F1(
) button (Make Folder) to create a folder, or press the
F3/HOME button (Cancel) to cancel creation.
All Del
Press 5 and b to select the desired menu item and press the center of the
Pointing Stick to use that function.
A pop-up message appears to confirm that you want to delete all the
files in the selected folder. Press the F1( ) button (Delete) to delete
the file, or press the F3/HOME button (Cancel) to cancel deletion.
Cancel
Do nothing with the selected folder and close the pop-up menu.
NOTE
Files that have been locked using a computer, as well as files and subfolders
that this unit cannot recognize cannot be deleted.
Select
Make the selected folder the current folder and return to the Home
Screen. The first file in the folder is selected. Regardless of the previous
playback area setting, this folder becomes the new playback area. New
recording files (video and audio) will also be stored in this folder.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
60
7 – Video and Audio Playback
On the Home Screen, press g or t to select the song (file) you want play
back. The files that you can select are determined by the playback area
setting. Limiting the play-back area makes file selection easier when, for
example, you have numerous files on a card.
On the PLAY AREAscreen, you can select all files (ALL), the current folder
(FOLDER) or a playlist (PLAY LIST) as the play-back area. You can also use the
BROWSEScreen to set a folder as the playback area.
Adjusting playback volume
On the Home Screen, press 5 and b to adjust the output level from the
built-in speaker and /LINE OUT jack.
NOTE
On the BROWSEScreen, regardless of the play-back area setting, you can
select any file on the card.
Setting the operation mode for playback
Only files that correspond to the active operation mode can be played back.
(See “Setting the operating mode”on page 35.)
Use video mode to playback video files or audio mode to playback audio files.
At this time, a volume level pop-up window appears.
The pop-up on the Home Screen closes automatically after a few seconds, but
you can also press the F3/HOME button to close the pop-up immediately.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
61
7– Video andAudioPlayback
4. Press 5 and b to set the playback area.
Setting the playback area
ALL (Default)
Play back all the files in the MY_FOLDER folder on the microSD card.
FOLDER
Use the PLAY AREAitem on the Play Optionscreen to set the
playback area.
Play back all the files in the folder of the currently selected file.
PLAY LIST
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the PLAY menu item and then press the
Play back the files in the playlist. (See “Playlist”on page 65.)
If you select this and there is no playlist, the No PLAYLIST pop-up
appears.
center of the Pointing Stick to open the Play Optionscreen.
5. After you have made the setting, press the F3/HOME button to return to
the Home Screen.
NOTE
The current playback area setting appears at the bottom right of the Home
Screen.
3. Press 5 and b to select PLAY AREAand press t or the center of
the Pointing Stick.
Playback area
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
62
7 – Videoand AudioPlayback
4. Press the center of the Pointing Stick to open the following pop-up
window.
Setting a folder as the playback area on the
BROWSE screen (method 1)
Regardless of the current playback area, if you select a folder on the
BROWSEScreen, the selected folder be-comes the playback area.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the BROWSEmenu item and then press
the center of the Pointing Stick to open the BROWSEscreen.
Press 5 and b to highlight Select and press the center of the Pointing
Stick.
The Home Screen reopens and the first file in the folder is selected.
Regardless of the previous playback area setting, this folder becomes the
new playback area.
3. Press 5 and b to select the folder you want to set as the playback area.
For an explanation of how to use the BROWSEScreen, see “Navigating
the BROWSE screen”on page 56.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
63
7– Video andAudioPlayback
6. Press the center of the Pointing Stick to open the following pop-up
window.
Setting a folder as the playback area on the
BROWSE screen (method 2)
When the playback area is set to FOLDER, if you select a file on the BROWSE
screen, the folder that contains the selected file becomes the playback area.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the BROWSEmenu item and then press
the center of the Pointing Stick to open the BROWSEscreen.
Press 5 and b to select Play and press the center of the Pointing Stick.
The Home Screen reopens and the selected file starts playing. If the
playback area is set to FOLDER, the folder that contains the selected file
becomes the playback area.
3. Press 5 and b to then select the folder that contains a video or audio
file you want to play back.
For an explanation of how to use the BROWSEScreen, see “Navigating
the BROWSE screen”on page 56.
4. Press t.
5. Select a file you want to play back.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
64
7 – Videoand AudioPlayback
List display mode
Playlist
You can make a playlist of files for playback.
Set the PLAY AREAitem to PLAY LISTon the Play Option
screen to play back the songs in a playlist.
There is one playlist for each operation mode, and you can make, edit and use
these independently.
Playlists can be viewed in either of two modes: THUMBNAIL that shows an
image for each file and FILE that shows a list of icons and file names.
Thumbnail display mode (default):
Operation mode
The icon at the upper left corner shows the cur-rent operation mode.
List numerical order
The order of each file in the list is shown in brackets.
File name list
The names of the files in the current playlist are shown in a list. The
currently selected file is shown with an orange background.
Icons that show the file type are shown next to the file names.
NOTE
•
For explanations of the icons shown, see “Icons shown in list view”on
page 58.
Operation mode
•
File names in Japanese and other languages that use multibyte
encodings cannot be shown correctly.
The icon at the upper left corner shows the cur-rent operation mode.
List numerical order
The order of each file in the list is shown in brackets.
File name
The name of the currently selected file is shown with an icon for the
file type before it.
File thumbnails
File thumbnails are shown.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
65
7– Video andAudioPlayback
Adding files to a playlist
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the BROWSEmenu item and then press
Editing a playlist
View the playlist you have made on the PLAYLISTscreen. Use this screen
also to play back files and edit the playlist.
the center of the Pointing Stick to open the BROWSEscreen.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the PLAYLISTmenu item and then
NOTE
press the center of the Pointing Stick to open the PLAYLISTscreen.
For an explanation of how to use the BROWSEScreen, see “6 – Working with
files and folders on the BROWSE screen”on page 56.
3. Press 5 and b to select the file you want to add to a playlist and press
the center of the Pointing Stick to open a pop-up window.
NOTE
For details about how to select the file, see “Navigating the BROWSE screen”
on page 56.
4. Use the Pointing Stick to select Add List.
5. Press the center of the Pointing Stick to add the selected file to the
playlist and close the pop-up window.
6. Repeat steps 3–5 as necessary to add more files to the playlist. The files
are numbered in the order that they are added.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
66
7 – Videoand AudioPlayback
Move
3. Press 5 and b to select the file you want to edit and press the center of
Change the order of files in a playlist. Along with the file name, the
playlist order number will also appear highlighted.
the Pointing Stick to open a pop-up menu.
•
Press 5 and b to move the selected file in the playlist.
4. Press 5 and b to select the desired menu item and press the center of
the Pointing Stick to use that function.
Cancel
In the above illustration, the 2nd file has been moved to the 3rd
place.
Press the center of the Pointing Stick to confirm the change and
end Move mode.
Do nothing with the selected file and close the pop-up menu.
Play
Return to the Home Screen and play back the file.
Info
Open a pop-up that shows information (name, format, size, time and
date) about the selected file. Press the F3/HOME button (Close) to
return to the PLAYLISTscreen.
•
Delete
Remove the selected file from the playlist. The removed file is not
deleted from the microSD card.
All Clr
Open a confirmation message to confirm that you want to remove all
the files from the playlist. Press the F1( ) button (YES) to clear
the playlist, or press the F3/HOME button (NO) to cancel.
For this operation, it does not matter which file you select in step 3.
All the files are removed from the playlist, but they are not deleted
from the microSD card.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
67
7– Video andAudioPlayback
Pausing and stopping playback
Skipping to select files for playback
When the Home Screen is open, press the STOP/PAUSE button to pause
playback at the current position.
Press the STOP/PAUSE button again to stop playback and return to the
beginning of the file.
When playback is paused, press the PLAY button to restart playback from the
current position.
On the Home Screen, use g and t to skip to the file you want to play back.
Press g when in the middle of a file to skip to the beginning of that file. Press
g when at the beginning of a file to skip to the beginning of the previous file.
At the beginning or middle of a file, press t to skip to the beginning of the
next file.
NOTES
•
•
Only files in the playback area can be played.
The track name, file number and other file information for the currently
playing file appear on the display.
•
The
icon appears on the display when playback is stopped at the
beginning of a file, and the icon appears when playback is paused in
the middle of a file.
Playback
When the Home Screen is open, press the PLAY button when playback is
stopped to start playback.
NOTES
•
•
•
Only files of the type that suits the current operation mode in the
playback area can be selected and played.
You can also choose any file of the type that suits the current operation
mode for playback by name on the BROWSEscreen.
This recorder can only play mov files that it created.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
68
7 – Videoand AudioPlayback
Searching backward and forward
On the Home Screen, press the zoom control left or right (W [m] or T
[,]) while a file is playing back, paused or stopped to search backward or
forward.
Search speed adjustment
The search speed can be changed as follows.
Status before searching starts
Stopped/Paused Playing back
No sound is output when rewinding or fast-forwarding.
Press W [m] or T
[,] repeatedly
×10 w ×100 w ×1000 ×5 w ×10 w ×50
Press briefly toward W [m]
Search backward to the beginning of the file where it will stop.
Depends on CUE/
Fixed at ×10
Press W [m] again to change the search speed.
Press and hold
REV SPEED setting
Press briefly toward T [,]
Search forward to the beginning of the next file where it will stop.
Press T [,] again to change the search speed.
Press and held toward W [m]
Search backward for as long as you keep pressing (searching does not
stop at the file beginning). Playback resumes at the point when you stop
pressing.
Press and held toward T [,]
Search forward for as long as you keep pressing (searching does not stop
at the file end). Playback resumes at the point when you stop pressing.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
69
7– Video andAudioPlayback
Setting the search speed
Repeat playback (REPEAT)
Use the CUE/REV SPEEDitem on the Play Optionscreen to set
the backward/forward search speed when the zoom control is pressed and
held during playback.
You can repeatedly play back one file or multiple files within the designated
playback area.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the PLAY menu item and then press the
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the PLAY menu item and then press the
center of the Pointing Stick to open the Play Optionscreen.
center of the Pointing Stick to open the Play Optionscreen.
3. Press 5 and b to select REPEAT and press t or the center of the
Pointing Stick.
4. Press 5 and b to set the repeat mode.
3. Press 5 and b to select CUE/REV SPEEDand press t or the
center of the Pointing Stick.
OFF
All files in the playback area are played in sequence one
(default) time. (This is the ordinary playback mode.)
ON
All songs in the selected playback area are played back
in order repeatedly. The
Screen.
icon appears on the Home
SINGLE
One song is played back repeatedly. The
on the Home Screen.
icon appears
5. When done changing the setting, press the F3/HOME button to return to
the Home Screen.
4. Press 5 and b to change the search speed setting.
Options: ×2 (double speed, default) to ×10 (in increments of 1)
5. When done changing the setting, press the F3/HOME button to return to
the Home Screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
70
7 – Videoand AudioPlayback
4. Press the center of the Pointing Stick to turn I/O LOOP playback ON. The
icon appears on the Home Screen during loop playback.
Looping playback
Using the I/O LOOP function, you can continuously repeat (loop) playback of a
section between IN and OUT points that you set.
1. On the Home Screen, during playback or when playback is stopped
or paused, press the F1(
LOOP SETTINGpop-up.
) button (I/O LOOP) to open the I/O
Press the center of the Pointing Stick again to turn I/O LOOP playback
OFF. The
icon disappears from the Home Screen when OFF.
5. Press the F3/HOME button (CLOSE) to close the loop playback pop-up.
NOTES
•
To cancel I/O LOOP playback, press the F1(
) button (I/O LOOP) to
open the I/O LOOP SETTINGpop-up, and press the center of
If stopped or paused, press PLAY button to start playback.
2. Press the F1( ) button (IN) to set the current point as the starting
the Pointing Stick to turn IN-OUT looped playback OFF. The
disappear.
The IN (starting) and OUT (ending) points cannot be set in different files.
icon will
(IN) point of the section to be played repeatedly.
The mark appears under the playback position bar to show the
location of the start (IN) point.
•
3. Press the F2 button (OUT) to set the current point as the end (OUT) point
of the section to be played repeatedly.
The mark appears under the playback position bar to show the
location of the OUT point.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
71
7– Video andAudioPlayback
NOTES
Using VSA playback
•
•
You can use this function only in video and audio modes.
Using the speed control function of this unit, the speed of audio is always
changed without changing its pitch. You can also set this with the SPEED
item on the PB Control screen.
This recorder includes a Variable Speed Audition (VSA) function that allows
you to change the playback speed without changing the pitch.
You can use the VSA function to make practicing and learning musical phrases
easier.
•
When using a file with 96kHz sampling frequency, the speed control
function is automatically disabled and SPEED does not appear on the
screen.
Setting the playback speed (method 1)
Press the F3/HOME button on the Home Screen to open the SPEED
CONTROLpop-up where you can adjust the speed.
Press g and t to adjust the playback speed.
After adjusting the speed, you can turn the VSA function OFF by pressing the
F1(
) button (SPEED OFF).
When VSA is active, a number appears at the top of the Home Screen.
Playback speed
When the SPEED CONTROLpop-up is open, press the F1(
) button
to turn speed control ON/OFF. This allows you to switch between the set
speed and the normal speed easily.
The speed can be set in a range between 50% (x0.5) and 150% (x1.5) in 10%
(0.1) increments (default: x1.0).
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
72
7 – Videoand AudioPlayback
Setting the playback speed (method 2)
You can set the playback speed control on the PB Controlscreen.
Deleting the selected file
Use the following procedure to delete the current file without opening the
BROWSEscreen.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the PB CONTROLmenu item and
then press the center of the Pointing Stick to open the PB Control
screen.
1. On the Home Screen, use g and t to select the file you want to delete.
2. During playback or when playback is stopped or paused, press the F2
button (DELETE) to open the FILE DELETEconfirmation pop-up.
3. Press t or the center of the Pointing Stick.
3. If you want to delete the file shown, press the F1(
) button (YES) to
delete the file and close the pop-up. The next file in the playback area is
loaded automatically in a stopped state.
Press the F3/HOME button (NO) to cancel deletion and close the pop-up.
NOTE
You can also delete files from the BROWSEscreen. (See “File operations”on
page 59.)
4. Press 5 and b to set the speed.
The speed can be set in a range between x0.5 and x1.5 in x0.1 increments
(default: x1.0).
5. When done changing this setting, press the F3/HOME button to return
to the Home Screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
73
8 – Viewing a slide show of still photos
In addition to the playback of video and audio files, you can view a slide show
of still images on this unit.
4. Press 5 and b to set the amount of time that each photo is shown in
the slide show.
Setting the operation mode
To view a slide show of still images on this unit, first activate photo mode. (See
“Setting the operating mode”on page 35.)
Setting the time each photo is shown
You can set the length from 1 sec to 10 sec in increments of 1 second.
(default: 3 sec)
You can set the amount of time that each still image is shown.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select PLAY and press the center of the Pointing
5. When setting is complete, press the F3/HOME button to return to the
Home Screen.
Stick to open the Play Optionscreen.
3. Press 5 and b to select SLIDE SHOW and press t or the center of the
Pointing Stick.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
75
8– Viewing aslideshow of still photos
Playing the slide show
On the Home Screen, press the PLAY button to start playback.
Stopping the slide show
On the Home Screen, press the STOP/PAUSE button during the slide show to
pause on the current photo.
Press the PLAY button again to resume playback of the slide show from the
same photo.
NOTE
Playback area and playlist settings also affect slide shows. For details, see “7 -
Video and Audio Playback”starting on page 61.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
76
9 – Connecting with a computer
By connecting this unit to a computer using a USB cable, you can transfer
video, photo and audio files between the microSD card in the unit and the
computer.
CAUTIONS
•
USB bus power is not supported. So, batteries will be drained as usual
when you connect the unit to a USB port.
This unit can use files with the following formats.
•
This unit cannot be operated when connected by USB.
When connected, the USB connectedmessage appears on the display
of the unit.
Video
MOV: SD and HD files recorded (video/audio) by a DR-V1HD
Audio
WAV: 16 or 24-bit WAV with 44.1, 48 or 96kHz sampling frequency
Image
JPG: JPEG files with 640x480 or 1280x720 resolution created
by a DR-V1HD
Make sure that the microSD card is inserted properly. If the microSD card is
not loaded properly, a “NO SDCARD”pop-up message appears.
When loaded properly, this unit appears on the computer as an external
volume named “DR-V1HD”.
Mini-B USB plug
Computer
USB
NOTE
Instead of connecting the unit to a computer via USB, you can also conduct
the same operations by removing the microSD card from the unit and loading
it directly (or using a card adapter) on a computer.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
77
9– Connectingwitha computer
CAUTION
Transferring files to a computer
•
File names and folder names in Japanese and other languages that use
multibyte encodings cannot be shown correctly.
1. Click the “DR-V1HD”drive on the computer screen to show the “MY_
FOLDER”and “UTILITY”folders.
•
Do not change the name of the MY_FOLDER folder. If the name of this
folder is changed, this unit will not be able to recognize the files in it.
2. Open “MY_FOLDER”and drag and drop the files that you want to transfer
to where you want them on the computer.
Disconnecting from a computer
CAUTION
•
USB bus power is not supported. So, batteries will be drained as usual
when you connect the unit to a USB port.
To transfer files to a computer, make sure that batteries have sufficient
remaining power or use the TASCAM PS-P520 AC adapter (sold
separately).
Before disconnecting the USB cable, follow the appropriate procedures for
your computer to eject the unit (as an external drive). See the computer’s
operation manual for instructions about how to eject an external drive.
After being ejected, the unit will shut down and power off automatically.
•
Do not change the name of the MY_FOLDER folder. If the name of this
folder is changed, this unit will not be able to recognize the files in it.
Transferring files from a computer
Only video and still image files recorded by this recorder can be loaded.
1. Click the “DR-V1HD”drive on the computer screen to show the “MY_
FOLDER”and “UTILITY”folders.
2. Open “MY_FOLDER”and drag and drop the files on the computer that
you want to transfer into this folder as you like.
TIPS
•
•
You can manage “MY_FOLDER”from the computer.
You can create sub-folders in the “MY_FOLDER”folder, but the unit
only recognizes the first level of sub-folders. The unit will not recognize
subfolders or their contents on the second level or below.
•
•
Since you can set the unit to only play the con-tents of a specific folder,
you can organize files into genres, artists or other categories as you like.
By naming subfolders and songs as you like, you will be able to identify
them by these names on the Home Screen and BROWSEscreen on this
unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
78
10 – Making other settings and viewing information
INFORMATION (FILE) screen
The INFORMATION (FILE)screen shows information about the
Viewing File Information (INFORMATION)
currently loaded file.
Use the INFORMATIONScreen to view various types of information about
the unit.
Follow the procedures below to open the INFORMATIONscreen.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select SETUPand press the center of the
Pointing Stick to open the Setupscreen.
3. Press 5 and b to select INFORMATIONand press t or the center
of the Pointing Stick.
4. Press 5 and b to select the item you want to check and press the
center of the Pointing Stick.
FILE
MOV/WAV/JPG
Information about the currently loaded file
Information, including resolution, frame rate, stereo/mono and sampling
frequency, is shown according to the type of file currently loaded.
CARD
Usage status of the currently inserted microSD card
SYSTEM
TITLE
Information about the unit’s system settings and firmware version
Shows the file name.
5. When done changing the setting, press the F3/HOME button to return to
NOTE
the Home Screen.
File names in Japanese and other languages that use multibyte encodings
cannot be shown correctly.
DATE
Shows the date of file creation.
SIZE
Shows the file size.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
79
10 –Making other settings and viewing information
INFORMATION (CARD) screen
The INFORMATION (CARD)screen shows the usage status of the
INFORMATION (SYSTEM) screen
The INFORMATION (SYSTEM)screen shows the automatic power
currently inserted microSD card.
off and battery type settings as well as the system firmware version.
TOTAL FILE
AUTO OFF
Shows the number of playable files.
Shows the AUTO OFFsetting
TOTAL FOLDER
BATTERY
Shows the number of folders.
Shows the battery type setting
TOTAL SIZE
System Version
Shows the total microSD card capacity.
Shows the system firmware version.
NOTE
REMAIN SIZE
The AUTO OFFand BATTERYsettings cannot be changed on this
screen. For instructions about changing these set-tings, see “Using the AUTO
OFF function”and “Setting the battery type”on page 81.
Shows the remaining open capacity of the microSD card.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
80
10 – Making other settings andviewinginformation
Using the AUTO OFF function
Use the AUTO OFFitem set how long until the power turns off
System settings (SETUP screen)
automatically after the last use or operation.
On the SETUPscreen, you can change various settings to optimize the unit
for your use environment and other requirements. You can also initialize the
unit, and format microSD cards.
Options : OFF, 3min, 5min, 10min, 30min(default)
Follow the procedure below to open the SETUPscreen.
Using the backlight auto off function
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select the SETUPmenu item and then press
Use the BACKLIGHTitem to set the time until the back-light automatically
turns off after the last operation when powered with batteries.
the center of the Pointing Stick to open the Setupscreen.
Options : ON (backlight not automatically turned off), 5sec, 10sec, 15sec,
30sec
Adjusting the backlight brightness
Use the DIMMERitem to adjust the backlight brightness.
Options : HIGH (default), LOW, ALL OFF (backlight off)
Setting the battery type
3. Press 5 and b to select the item that you want to set. (See the
Use the BATTERYitem to set the type of the batteries used in the unit.
This setting is used to show the amount of remaining battery charge and
determine if the unit has enough power for normal operation.
following sections for details about each item on the Setupscreen.)
4. When done changing the setting, press the F3/HOME button to return to
the Home Screen.
Options: ALKAL (default, alkaline), NIMH (nickel-metal hydride)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
81
10 –Making other settings and viewing information
File name format
Set the TYPE item to WORD or DATE.
Setting the format of file names
WORD : (Default) The 6 characters set in the WORD item are used as the
beginning of each file name.
Example : DR0000_0000.mov
DATE : The date is used as the beginning of each file name in a
yymmdd format.
Use the FILE NAMEitem on the Setupscreen to set the format of
names given automatically to recorded files (video, audio and photo).
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select SETUPand press the center of the
Pointing Stick to open the Setupscreen.
3. Press 5 and b to select FILE NAMEand press t or the center of
Example : 090101_0000.mov
NOTE
the Pointing Stick to open the FILE NAMEscreen.
The date is set using the unit’s internal clock. (See “Setting the date and time”
on page 31.)
Setting the WORD item
Select the WORD item, and use g or t to move the cursor. Press 5 and b
to set the characters.
In addition to the English alphabet and numbers, the following characters can
be used:
! # $ % & ’( ) + , - . ; = @ [] ^ _ ` { } .
4. Press g and t to change the selection, and press up and down to set
each item.
5. Press the F1(
) button (SET) to confirm a change and return to the
Setupscreen.
Press the F3/HOME button (INC CLEAR) to restart the automatic numbering
added to incremented file names.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
82
10 – Making other settings andviewinginformation
4. Press the F1(
) button (YES) to start formatting.
Formatting
Press the F3/HOME button if you want to cancel formatting.
When formatting completes, the following pop-up message opens.
Use the SD FORMAT item on the Setupscreen to fully format the microSD
card. Fully formatting a card erases all music files on it and automatically
creates new “MY_FOLDER”and “UTILITY”folders, as well as a “.NVRAM.txt”file.
CAUTION
Although you can access the “.NVRAM.txt”file when the recorder is connected
to a computer if you edit it or otherwise change it, the recorder might stop
functioning properly.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select SETUPand press the center of the
Pointing Stick to open the Setupscreen.
3. Use the Pointing Stick to select the SD FORMAT item and press t or the
CAUTION
When formatting a card, power the unit with a TASCAM PS-P520 AC adapter
(sold separately) or make sure the batteries have sufficient remaining power. If
the power fails during formatting, the formatting may not complete correctly.
center of the Pointing Stick to open the following pop-up confirmation.
5. Press the center of the Pointing Stick to return to the Setupscreen.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
83
10 –Making other settings and viewing information
Restoring the default settings
Use the INITIALIZE item on the Setupscreen to restore the various settings
of this unit to their factory default settings.
1. Press the MENU button to open the MENUscreen.
2. Use the Pointing Stick to select SETUPand press the center of the
Pointing Stick to open the Setupscreen.
3. Use the Pointing Stick to select the INITIALIZE item and press t or the
center of the Pointing Stick to open the following pop-up confirmation.
4. Press the F1(
) button (YES) to start initialization.
Press the F3/HOME button (NO) to cancel initialization.
CAUTION
Initialization when a card is in use does not reset the file numbers added
automatically to filenames.
To reset the file numbers, see the instructions in “Setting the format of file
names”on page 82.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
84
11 – Messages
The following is a list of the pop-up messages that may appear under certain conditions.
Refer to this list if one of these pop-up messages appears and you want to check the meaning or determine a proper response.
Message
Battery Empty
Can’t Divide
Meaning and response
The batteries are out of power. Replace them. Alternatively, use a TASCAM PS-P520 AC adaptor (sold separately).
The position selected for dividing is not suitable (too close to the beginning or end of the file). Divide the file at a suitable
position.
Card Error
The unit could not use the card properly. Replace the card.
Card Full
Dup File Name
The card has no remaining capacity. Erase unnecessary files or move them to a computer to make open space.
The DIVIDE function has caused the file name to be the same as that of an existing file. The DIVIDE function adds “_a”or “_b”to
the end of the original file name. Before dividing, connect the unit to a computer and edit the file name.
The total number of folders and files exceeds 9999. Erase unnecessary items or move them to your computer.
The DIVIDE function has caused the file name to exceed 200 characters. The DIVIDE function adds “_a”or “_b”to the end of the
original file name. Before dividing, connect the unit to a computer and edit the file name to 198 characters or less.
A file added to a playlist cannot be found. Please confirm that the file is in the active folder.
The file is read-only so it cannot be deleted. Use a computer to delete read-only files.
File Full
File Name ERR
File Not Found
File Protected
Format Error
Format CARD
The formatting of the card might be in-correct or the card might be broken. This message also appears if you format a card
using a computer connected by USB or if you insert an unformatted card in the unit. Always use the DR-V1HD to format cards
to be used with it. Change the card, or press the F1(
formatting erases all data on the card.
) button (YES) while this message appears to FAT format the card. FAT
I/O Too Short
Non-Supported
No PLAYLIST
The interval between the IN and OUT points is too short. Set them at least one second apart.
The file is not a supported format. Please see “9 – Connecting with a computer”for file formats that this unit can use.
No files have been added to the playlist. Add a file to the playlist or change the play mode to something other than PLAYLIST.
The SD card does not have enough open space to use the DIVIDE function. At least as much open space as the size of the file
being divided is necessary.
Out Of Card Space
Delete unneeded files from the card. Back up files that you might want later to a computer before deleting them.
The playlist is full. You cannot add more than 99 files to a playlist.
In video recording mode, recording is not possible when the sampling frequency is set to 96kHz.
Set the sampling frequency to 44.1kHz or 48kHz.
Writing to the card timed out. Backup the files on the card to a computer and format the card.
No microSD card is inserted in the recorder. Insert a card properly.
There is no file that can be viewed when browsing.
PLAYLIST Full
Unsupported
Sampling Rate!!
Write Timeout
NO SDCARD
No File
No Movie File
No Audio File
There is no video file (mov) in the playback area.
There is no audio file (wav) in the playback area.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
85
11 –Messages
Message
No Photo File
System Error
Meaning and response
There is no still image file (jpg) in the playback area.
An error has occurred related to the CPU, data transmission or another aspect of the system.
If one of these errors occurs, turn the recorder’s power OFF once and then restart it.
If you are unable to turn the power off, remove the batteries and disconnect the TASCAM PS-P520 AC adaptor.
If system errors occur frequently, please contact a TASCAM service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
86
12 – Troubleshooting
If you are having trouble with the operation of this unit, please try the
following before seeking repair. If these measures do not solve the problem,
please contact the store where you bought the unit or TASCAM Customer
Support.
No sound from the speaker.
e
Are headphones connected?
e
Is the SPEAKER switch set to OFF?
No sound from connected monitoring system.
Power will not turn ON.
e
e
e
Check the connections with the monitoring system.
Is the volume of the monitoring system minimized?
Is the OUTPUT LEVEL setting of the unit minimized?
e
Confirm that the batteries are not dead.
e
Make sure that the batteries are installed with the correct ¥/^
orientations.
e
If using a TASCAM PS-P520 AC adapter (sold separately), confirm that its
plug is inserted securely into an outlet.
Recording (video/audio/photo) is not possible.
e
e
e
e
e
If you are using an external device, check the connections again.
Check the input settings again.
Confirm that the recording level is not too low.
Confirm that the microSD card is not full.
Confirm that the number of files has not reached the maximum that the
unit can handle.
The unit does not function.
e
Confirm that the HOLD switch is not set in the direction of the arrow.
e
Confirm that the unit is not connected by USB to a computer (unit
display shows “USB Connected”).
The microSD card is not recognized.
Input level is low.
e
Confirm that the microSD card is inserted completely.
e
e
e
Confirm that the input level setting is not too low.
Confirm that the gain setting is not too low.
Confirm that the output level of any connected external device is not
too low.
Playback does not work.
e
This recorder can only play mov files that it created.
e
If you are trying to play a WAV file, confirm that the sampling frequency
is supported by this unit.
The sound I am trying to record sounds distorted.
e
Confirm that the INPUT volume setting is not too high.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
87
12 –Troubleshooting
Playback sounds unnatural.
e
Confirm that the playback speed is not being adjusted.
I cannot erase a file.
e
Are you trying to erase a copy of a file that was set to read-only on a
computer?
This unit’s files do not appear on the computer.
e
e
e
Confirm that the unit’s USB port is connected to the computer.
Confirm that you are not using a USB hub.
Confirm that the unit is not recording or in recording standby mode
(audio/video/photo).
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
88
13 – Specifications
Media and formats
Inputs and outputs
Recording media
Analog audio input and output
microSD card (64 MB – 2 GB)
microSDHC card (4 GB – 32 GB)
MIC/LINE IN jack (plug-in power supported)
Connector
: 1/8”(3.5mm) stereo mini jack
Video recording/playback format
INPUT SELECT set to MIC
Input impedance
Nominal input level
MOV
: 25 kΩ
Video compression method
Audio
Resolution
: MPEG4-SP
: WAV 44.1/48kHz, 16/24-bit
: SD 640×480 (30 fps)
GAIN LOW : -32 dBV
GAIN MID : -48 dBV
GAIN HIGH : -64 dBV
HD 1280×720 (30 fps)
Audio recording/playback format
Maximum input level
GAIN LOW : -16 dBV
GAIN MID : -32 dBV
GAIN HIGH : -48 dBV
WAV
: 44.1/48/96kHz, 16/24-bit
Still image format
Size
: 0.3M 640×480
0.9M 1024×720
INPUT SELECT set to LINE
Input impedance
: 22 kΩ
Nominal input level
Minimum input level
Maximum input level : +6 dBV (2.0 V)
: -10 dBV (0.32 V)
: -22 dBV (0.08 V)
Number of channels
Video/photo
Audio
: 1
: 2 (stereo)
/LINE OUT jack
Connector
Output impedance
Nominal output level
Maximum output level
Maximum output
: 1/8”(3.5 mm) stereo mini jack
: 12 Ω
: –14 dBV (10 kΩ load)
: +2 dBV (10 kΩ load)
: 15 mW + 15 mW (32Ω load)
Built-in speaker
0.6 W (monaural)
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
89
13 –Specifications
Built-in microphone
Audio performance
Electret condenser microphone pair (stereo)
Directivity
: Unidirectional
Sensitivity : -37 dB at 1 kHz (0 dB = 1 V/Pa) RL = 2 kΩ, Vcc = 3 V
Impedance : 1.4 kΩ 30% at 1 kHz (RL = 2 kΩ)
Frequency response
20 Hz – 20 kHz +1/–3 dB (LINE IN to LINE OUT, 44.1 kHz, JEITA)
20 Hz – 22 kHz +1/–3 dB (LINE IN to LINE OUT, 48 kHz, JEITA)
20 Hz – 40 kHz +1/-3 dB (LINE IN to LINE OUT, 96 kHz, JEITA)
S/N ratio
: 74 dB typical at 1 kHz (A-Weight)
: 120 dB
Maximum input sound pressure level (SPL)
Built-in camera
Total harmonic distortion
Image sensor
Resolution
Lens
: 1/4-inch CMOS
: 1.0 megapixel (1280 x 800)
Angle of view
Focal length
0.02% or less (LINE IN to LINE OUT, 44.1/48/96 kHz, JEITA)
S/N ratio
: 64º
: 39 cm–∞
90 dB or more (LINE IN to LINE OUT, 44.1/48/96 kHz, JEITA)
Note: JEITA CP-2150 measurement methods used
Digital connections
USB port
Connector
: Mini-B type
Format
: USB 2.0 Hi-Speed mass storage device class
mini-HDMI port
Connector
: Type C
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
90
13 – Specifications
Computer compatibility
Other specifications
Visit the TASCAM website (http://tascam.com/) for updated information about
operating system compatibil-ity.
Power supply
Three AA batteries (Alkaline or Ni-MH)
Windows
TASCAM PS-P520 AC adaptor (sold separately)
Pentium (300 MHz or faster)
128 MB or more memory
USB port (USB 2.0 recommended)
Power consumption
0.9 W (maximum)
Battery operation time (continuous)
Macintosh
•
Alkaline type battery (EVOLTA)
Power PC, iMac, G3, G4 (266 MHz or faster)
64 MB or more memory
USB port (USB 2.0 recommended)
Continuous
operation
time
Operation File format
Note
Recommended USB host controller
(approximate)
Intel chipset
Using built-in
Recording HD-720p video
with 48kHz, 24-bit audio
3.5 hours
4.5 hours
stereo microphone
and headphones
Using built-in
stereo microphone
and headphones
Supported operating systems
Windows: Windows XP, Windows Vista, Windows 7
Macintosh: Mac OS X 10.2 or later
Recording SD-VGA video
with 44.1kHz, 16-bit audio
Video
mode
Playing HD-720p video with
48kHz, 24-bit audio
Playing SD-VGA video with
44.1kHz, 16-bit audio
4.5 hours
5.5 hours
Using headphones
Using headphones
Using built-in
Recording 96kHz, 24-bit
audio
5 hours
6 hours
stereo microphone
and headphones
Using built-in
stereo microphone
and headphones
Audio
mode
Recording 44.1kHz, 16-bit
audio
Playing 96kHz, 24-bit audio 6 hours
Playing 44.1kHz, 16-bit audio 6.5 hours
Using headphones
Using headphones
Note: times for music recording and playback measured using JEITA methods
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
91
13 –Specifications
•
Ni-MH type battery (eneloop)
Operation File format
Recording HD-720p video
Dimensional drawings
Continuous
operation time Note
(approximate)
Using built-in
4.5 hours
stereo microphone
and headphones
Using built-in
stereo microphone
and headphones
with 48kHz, 24-bit audio
Recording SD-VGA video
with 44.1kHz, 16-bit audio
5.5 hours
Video
mode
Playing HD-720p video
with 48kHz, 24-bit audio
Playing SD-VGA video with
44.1kHz, 16-bit audio
5 hours
6 hours
Using headphones
Using headphones
Using built-in
Recording 96kHz, 24-bit
audio
5.5 hours
6.5 hours
stereo microphone
and headphones
Using built-in
stereo microphone
and headphones
Recording 44.1kHz, 16-bit
audio
Audio
mode
Playing 96kHz, 24-bit audio 5 hours
Using headphones
Playing 44.1kHz, 16-bit
audio
6 hours
Using headphones
Note: times for music recording and playback measured using JEITA methods
28mm
70mm
Dimensions
70 × 131 × 28 mm (W × H × D)
•
•
Illustrations in this manual might differ in part from the actual product.
Specifications and external appearance may be changed without
notification in order to improve the product.
Weight
157 g (excluding batteries)
Operating temperature range
0–35º C
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
92
14 – Important notice regarding software
All title and copyrights in and to the SOFTWARE and any copies thereof
are owned by TEAC or its suppliers. All title and intellectual property
rights in and to the content which may be accessed through use of the
Software License Agreement
SOFTWARE is the property of the respective content owner and may be
protected by applicable copyright or other intellectual property laws and
treaties. This Agreement grants you no rights to use such content.
END-USER LICENSE AGREEMENT FOR APPLICATION SOFTWARE ATTACHED TO
TEAC PRODUCTS
IMPORTANT - READ CAREFULLY:
5
6
NO WARRANTY.
This End-User License Agreement is a legal agreement between you (either
an individual or a single entity) and TEAC Corporation ("TEAC") for the
software identified above, which includes computer software and associated
media and printed materials (if any), and may include online or electronic
documentation (hereinafter referred to as SOFTWARE). By installing, copying,
or otherwise using the SOFTWARE, you agree to be bound by the terms of this
Agreement. If you do not agree to the terms of this Agreement, you are not
authorized to use the SOFTWARE.
ANY USE OF THE SOFTWARE IS AT YOUR OWN RISK. THE SOFTWARE IS
PROVIDED FOR USE ONLY FOR TEAC PRODUCTS. TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW, TEAC AND ITS SUPPLIERS
DISCLAIM ALL WARRANTIES AND CONDITIONS, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NONINFRINGEMENT.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES.
The SOFTWARE is protected by copyright laws and international copyright
treaties, as well as other intellectual property laws and treaties. The
SOFTWARE is licensed, not sold.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO
EVENT SHALL TEAC OR ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL
INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS
PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION,
OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF OR
INABILITY TO USE THE SOFTWARE, EVEN IF TEAC HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES AND
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
1
GRANT OF LICENSE.
This Agreement grants you the following rights:
Use and Copy. TEAC grants to you the right to use copies of the
SOFTWARE only for TEAC PRODUCTS you have. You may also make a
copy of the SOFTWARE for backup and archival purposes.
2
3
RESTRICTIONS.
You may not distribute copies of the SOFTWARE to third parties.
You may not rent or lease the SOFTWARE.
7
8
LIMITATION OF LIABILITY.
TERMINATION.
TEAC’S ENTIRE LIABILITY AND YOUR EXCLUSIVE REMEDY UNDER THIS
AGREEMENT SHALL NOT EXCEED THE PRICE YOU PAID FOR TEAC
PRODUCTS.
Your rights under this Agreement terminate upon the disposal of your
TEAC PRODUCTS, or without prejudice to any other rights, TEAC may
terminate this Agreement if you fail to comply with the terms and
conditions of this Agreement. In such event, you must destroy all copies
of the SOFTWARE.
MISCELLANEOUS.
This Agreement is governed by the laws of Japan.
4
COPYRIGHT.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
93
14 –Importantnotice regarding software
Notice regarding software that uses the GNU GPL
About the licensing of software used in this product
The software included in this product is comprised of multiple discrete
software applications, and the copyrights of each of these belong to various
third parties.
NOTICE
The reproduction and use of copyrighted materials such as music, images,
computer programs and databases are limited by the copyright and other
laws or by the license agreement made by and between the copyright
holders and users. Before making a reproduction of such materials,
check their conditions of use and use this product without infringing the
copyrights or other intellectual property rights. TEAC has no responsibility
for copyright infringement as a result of reproductions of copyrighted works
made by users of this product.
This product includes software covered by end-user license agreements
(hereafter, “EULA”) stipulated by third parties.
Among these is the GNU General Public License (hereafter, “GPL”) for free
executable software applications. As a condition for the distribution of
software covered by the GPL, the source code for such software must be
made available. If you wish to obtain the source code for such software, you
may do so by accessing the following URL and filling out a registration form.
http://www.teac.co.jp/support/opensource/index.html
Please understand that we are unable to respond to questions about the
source code contents and similar matters.
Source code will not be provided for software covered by EULAs other than
the GPL.
Software distributed in accordance with the GPL allows customers to use it
without charge, but, to the extent of applicable laws, no explicit or implicit
guarantees are provided for such software.
NOTE
Any data, including, but not limited to information, described herein are
intended only as illustrations of such data and/or information and not as
the specifications for such data and/or information. TEAC CORPORATION
disclaims any warranty that any use of such data and/or information shall
be free from infringement of any third party’s intellectual property rights
or other proprietary rights, and further, assumes no liability of whatsoever
nature in the event of any such infringement, or arising from or connected
with or related to the use of such data and/or information.
With the exceptions of provisions of applicable laws and written agreements,
the copyright holders and those who change and redistribute such software
with the permission described above will bear no responsibility for any loss
caused by the use of or the inability to use such software. Please read the GPL
for details about, for example, conditions for use and provisions that must be
followed regarding such software.
List of packages
(GNU GPL)
Linux-kernel.tar.gz
Advanced Linux Sound Architecture ALSA
busybox
Before using software or software components that are included in this
product and subject to the GPL, please read the following GNU GENERAL
PUBLIC LICENSE carefully. Moreover, since the provisions of this license are set
by a third party, we provide it in its original language (English).
(BSD)
DMAI
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
94
14 – Important notice regarding software
We protect your rights with two steps: (1) copyright the software, and (2) offer
you this license which gives you legal permission to copy, distribute and/or
modify the software.
GNU GENERAL PUBLIC LICENSE Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street,
Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
Also, for each author's protection and ours, we want to make certain that
everyone understands that there is no warranty for this free software. If the
software is modified by someone else and passed on, we want its recipients to
know that what they have is not the original, so that any problems introduced
Preamble
The licenses for most software are designed to take away your freedom to
share and change it. By contrast, the GNU General Public License is intended
to guarantee your freedom to share and change free software--to make sure
the software is free for all its users. This General Public License applies to most
of the Free Software Foundation's software and to any other program whose
authors commit to using it. (Some other Free Software Foundation software is
covered by the GNU Library General Public License instead.) You can apply it
to your programs, too.
by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We
wish to avoid the danger that redistributors of a free program will individually
obtain patent licenses, in effect making the program proprietary. To prevent
this, we have made it clear that any patent must be licensed for everyone's
free use or not licensed at all.
When we speak of free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you have the freedom
to distribute copies of free software (and charge for this service if you wish),
that you receive source code or can get it if you want it, that you can change
the software or use pieces of it in new free programs; and that you know you
can do these things.
The precise terms and conditions for copying, distribution and modification
follow.
GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR
COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a
notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The "Program", below, refers to
any such program or work, and a "work based on the Program" means
either the Program or any derivative work under copyright law: that is to
say, a work containing the Program or a portion of it, either verbatim or
with modifications and/or translated into another language. (Hereinafter,
translation is included without limitation in the term "modification".) Each
licensee is addressed as "you".
To protect your rights, we need to make restrictions that forbid anyone to
deny you these rights or to ask you to surrender the rights. These restrictions
translate to certain responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for
a fee, you must give the recipients all the rights that you have. You must make
sure that they, too, receive or can get the source code. And you must show
them these terms so they know their rights.
Activities other than copying, distribution and modification are not covered
by this License; they are outside its scope. The act of running the Program is
not restricted, and the output from the Program is covered only if its contents
constitute a work based on the Program (independent of having been made
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
95
14 – Important notice regarding software
by running the Program). Whether that is true depends on what the Program
does.
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves, then
this License, and its terms, do not apply to those sections when you distribute
them as separate works. But when you distribute the same sections as part of
a whole which is a work based on the Program, the distribution of the whole
must be on the terms of this License, whose permissions for other licensees
extend to the entire whole, and thus to each and every part regardless of who
wrote it.
1. You may copy and distribute verbatim copies of the Program's source
code as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer to this License and
to the absence of any warranty; and give any other recipients of the Program
a copy of this License along with the Program.
Thus, it is not the intent of this section to claim rights or contest your rights
to work written entirely by you; rather, the intent is to exercise the right
to control the distribution of derivative or collective works based on the
Program.
You may charge a fee for the physical act of transferring a copy, and you may
at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it,
thus forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you
also meet all of these conditions:
In addition, mere aggregation of another work not based on the Program
with the Program (or with a work based on the Program) on a volume of a
storage or distribution medium does not bring the other work under the
scope of this License.
a) You must cause the modified files to carry prominent notices stating
that you changed the files and the date of any change.
3. You may copy and distribute the Program (or a work based on it, under
Section 2) in object code or executable form under the terms of Sections 1
and 2 above provided that you also do one of the following:
b) You must cause any work that you distribute or publish, that in whole
or in part contains or is derived from the Program or any part thereof, to
be licensed as a whole at no charge to all third parties under the terms
of this License.
a) Accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of Sections 1
and 2 above on a medium customarily used for software interchange; or,
c) If the modified program normally reads commands interactively when
run, you must cause it, when started running for such interactive use in
the most ordinary way, to print or display an announcement including an
appropriate copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users may redistribute
the program under these conditions, and telling the user how to view
a copy of this License. (Exception: if the Program itself is interactive but
does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
b) Accompany it with a written offer, valid for at least three years, to
give any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable copy
of the corresponding source code, to be distributed under the terms
of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
96
14 – Important notice regarding software
c) Accompany it with the information you received as to the offer to
distribute corresponding source code. (This alternative is allowed only
for noncommercial distribution and only if you received the program
in object code or executable form with such an offer, in accord with
Subsection b above.)
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these terms and
conditions. You may not impose any further restrictions on the recipients'
exercise of the rights granted herein. You are not responsible for enforcing
compliance by third parties to this License.
The source code for a work means the preferred form of the work for making
modifications to it. For an executable work, complete source code means
all the source code for all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation and installation of
the executable. However, as a special exception, the source code distributed
need not include anything that is normally distributed (in either source or
binary form) with the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that component itself
accompanies the executable.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues), conditions
are imposed on you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do not excuse you
from the conditions of this License. If you cannot distribute so as to satisfy
simultaneously your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the Program at all.
For example, if a patent license would not permit royalty-free redistribution
of the Program by all those who receive copies directly or indirectly through
you, then the only way you could satisfy both it and this License would be to
refrain entirely from distribution of the Program.
If distribution of executable or object code is made by offering access to copy
from a designated place, then offering equivalent access to copy the source
code from the same place counts as distribution of the source code, even
though third parties are not compelled to copy the source along with the
object code.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply and
the section as a whole is intended to apply in other circumstances.
4. You may not copy, modify, sublicense, or distribute the Program except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate
your rights under this License. However, parties who have received copies, or
rights, from you under this License will not have their licenses terminated so
long as such parties remain in full compliance.
It is not the purpose of this section to induce you to infringe any patents
or other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software
distribution system, which is implemented by public license practices. Many
people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of
that system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot impose
that choice.
5. You are not required to accept this License, since you have not signed it.
However, nothing else grants you permission to modify or distribute the
Program or its derivative works. These actions are prohibited by law if you do
not accept this License. Therefore, by modifying or distributing the Program
(or any work based on the Program), you indicate your acceptance of this
License to do so, and all its terms and conditions for copying, distributing or
modifying the Program or works based on it.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
97
14 – Important notice regarding software
This section is intended to make thoroughly clear what is believed to be a
consequence of the rest of this License.
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
8. If the distribution and/or use of the Program is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add an
explicit geographical distribution limitation excluding those countries, so that
distribution is permitted only in or among countries not thus excluded. In
such case, this License incorporates the limitation as if written in the body of
this License.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF
DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED
9. The Free Software Foundation may publish revised and/or new versions
of the General Public License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in detail to address new
problems or concerns.
BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Each version is given a distinguishing version number. If the Program specifies
a version number of this License which applies to it and "any later version",
you have the option of following the terms and conditions either of that
version or of any later version published by the Free Software Foundation.
If the Program does not specify a version number of this License, you may
choose any version ever published by the Free Software Foundation.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible
use to the public, the best way to achieve this is to make it free software
which everyone can redistribute and change under these terms.
10. If you wish to incorporate parts of the Program into other free programs
whose distribution conditions are different, write to the author to ask
for permission. For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we sometimes make
exceptions for this. Our decision will be guided by the two goals of preserving
the free status of all derivatives of our free software and of promoting the
sharing and reuse of software generally.
To do so, attach the following notices to the program. It is safest to attach
them to the start of each source file to most effectively convey the exclusion
of warranty; and each file should have at least the "copyright" line and a
pointer to where the full notice is found.
NO WARRANTY
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE
LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
98
14 – Important notice regarding software
Free Software Foundation; either version 2 of the License, or (at your
option) any later version.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
This General Public License does not permit incorporating your program
into proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the
library.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software Foundation,
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110- 1301 USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it
starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision
comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This
is free software, and you are welcome to redistribute it under certain
conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the
appropriate parts of the General Public License. Of course, the commands you
use may be called something other than `show w' and `show c'; they could
even be mouseclicks or menu items-- whatever suits your program.
You should also get your employer (if you work as a programmer) or your
school, if any, to sign a "copyright disclaimer" for the program, if necessary.
Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
`Gnomovision' (which makes passes at compilers) written by James
Hacker.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
99
14 – Important notice regarding software
Notice regarding software that uses the BSD
BSD
Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
Neither the name of Texas Instruments Incorporated nor the names of its
contributors may be used to endorse or promote products derived from
this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
100
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
TASCAM DR-V1HD
101
User registration
Customers in the USA, please visit the TASCAM
website (http://tascam.com/) to register as a
user online.
DR-V1HD
TEAC CORPORATION
Phone: +81-42-356-9143
http://tascam.jp/
http://tascam.com/
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
7733 Telegraph Road, Montebello, California 90640 USA
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
http://tascam.com/
TEAC MEXICO, S.A. de C.V.
Phone: +52-55-5010-6000
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México
http://www.teacmexico.net/
TEAC UK LIMITED
Phone: +44-8451-302511
http://www.tascam.co.uk/
Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
http//tascam.de/
Printed in China
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Download from Www.Somanuals.com. All Manuals Search And Download.
|