D01055620A
DR-07
Portable Digital
Recorder
This device has a serial
number located on the
bottom panel. Please record it
and retain it for your records.
Serial number:
__________________
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Excessive sound pressure from earphones and headphones
an eye, wash it out thoroughly with clean water without
rubbing the eye and then consult a doctor immediately. If the
fluid gets on a person’s body or clothing, it could cause skin
injuries or burns. If this should happen, wash it off with clean
water and then consult a doctor immediately.
•
can cause hearing loss.
Warnings and Cautions about Batteries
This product uses batteries. Misuse of batteries could cause
a leak, rupture or other trouble. Always abide by the following
precautions when using batteries.
The unit power should be off when you install and replace
batteries.
•
•
Remove the batteries if you do not plan to use the unit for a
long time. Batteries could rupture or leak, causing fire, injury
or stains around them. If the battery fluid leaks, wipe away
any fluid on the battery compartment before inserting new
batteries.
Never recharge non-rechargeable batteries. The batteries
could rupture or leak, causing fire or injury.
•
•
When installing batteries, pay attention to the polarity indica-
tions (plus/minus (+/–) orientation), and install them correctly
in the battery compartment as indicated. Putting them in
backward could make the batteries rupture or leak, causing
fire, injury or stains around them.
When throwing used batteries away, follow the disposal
instructions indicated on the batteries and the local disposal
laws.
Do not use batteries other than those specified. Do not mix
and use new and old batteries or different types of batteries
together. The batteries could rupture or leak, causing fire,
injury or stains around them.
Declaration of Conformity
•
•
Model Number
: DR-07
Trade Name: TASCAM
Responsible party
: TEAC AMERICA, INC.
Address
: 7733 Telegraph Road, Montebello,
California, U.S. A.
Telephone number
: 1-323-726-0303
Do not carry or store batteries together with small metal
objects. The batteries could short, causing leak, rupture or
other trouble.
Do not heat or disassemble batteries. Do not put them in fire
or water. Batteries could rupture or leak, causing fire, injury
or stains around them.
If the battery fluid leaks, wipe away any fluid on the battery
case before inserting new batteries. If the battery fluid gets
in an eye, it could cause loss of eyesight. If fluid does enter
•
•
•
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference recieved,
including interference that may cause undesired
operation.
TASCAM DR-07 3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Information for Users on Collection and
Disposal of Old Equipment and used
FOR U.S.A.
TO THE USER
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and
receiver.
c) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
d) Consult the dealer or an experienced radio/TV
technician for help.
Batteries
These symbols on the products, packaging, and/or accompanying
documents mean that used electrical and electronic products and
batteries should not be mixed with general household waste. For
proper treatment, recovery and recycling of old products and
used batteries, please take them to applicable collection points,
in accordance with your national legislation and the Directives
2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will
help to save valuable resources and prevent any potential negative
effects on human health and the environment which could
otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old
products and batteries, please contact your local municipality,
your waste disposal service or the point of sale where you
purchased the items.
CAUTION
Changes or modifications to this equipment not expressly
approved by TEAC CORPORATION for compliance could
void the user's authority to operate this equipment.
Information on Disposal in other Countries
outside the European Union
These symbols are only valid in the European Union. If you wish
to discard these items, please contact your local authorities or
dealer and ask for the correct method of disposal.
4
TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Note for the battery symbol (bottom right
two symbol examples)
This symbol might be used in combination with a chemical
symbol. In this case it complies with the requirement set by the
Directive for the chemical involved.
Pb
TASCAM DR-07 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
6
TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Using QUICK FORMAT 78
TASCAM DR-07 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
8
TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
ing playback speed without changing pitch
and changing pitch without changing playback
speed.
Thank you very much for purchasing the TASCAM
DR-07 Portable Recorder. Please read this Owner’s
Manual carefully in order to maximize your use of
all the unit’s features. We hope that you will enjoy
using this recorder for many years to come. Please
make copies of this manual and keep them in safe
places for future reference.
Copy audio files from a computer to this unit’s
SD card by USB connection
•
About this manual
This manual is provided both as a printed
document and as an electronic file stored on the
included SD card.
Main functions
Portable recorder
Use SD cards as the recording media
•
•
To access the Owner’s Manual on the included
SD card, install the SD card in the unit if it has
not been installed already, and use the included
USB cable to connect the unit to a computer (see
“Connecting with a computer” on page 41 for how
to make the connection).
Record with the built-in microphone, or by
connecting a microphone or the line output of a
CD player, instrument or other audio device
Choose MP3 (32 kbps–320 kbps, 44.1 kHz or
48 kHz) or WAV (16-bit or 24-bit, 44.1 kHz or
48 kHz) audio file types for recording
•
The Owner’s Manual file is in the Manual folder
inside the DR-07 folder. In order to open the file,
Adobe Reader (or other software that can open
pdf files) must be installed on your computer.
TASCAM DR-07 9
Other features
Special playback functions include decreas-
•
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
Adobe Reader can be downloaded for free from the
Internet.
CAUTION
In this manual, we usually use the word “track”
when we are describing the playback of a song, for
example, just as we would if talking about songs
on a CD or a portable music player. However,
when we talk about their data properties, such as
sampling frequencies and ID3 tags, we often refer
to the same “tracks” as “files” because they can be
manipulated in ways similar to files on a computer.
• We recommend that you make a backup
copy of the Owner’s Manual file on your
computer hard disk, a CD-R or other
media.
• If you accidentally erase the Owner’s
Manual file, you can download it again
com).
TIP
We give hints and tips on using the DR-07
when you see this icon.
A note provides additional explanations
for special situations.
NOTE
Font use conventions
Controls, keys and other parts on the DR-07
•
•
•
A caution shows that you may
CAUTION
are written like this: MENU.
lose data (recordings) if you do not follow the
instructions.
Messages shown on the display are written like
this: Are you sure?
We use the term “key” to describe the push-
button controls on the DR-07.
Tracks and files are the same
Tracks are files, and files are tracks.
10 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
Microsoft, Windows, Windows XP, and Windows
Vista are either registered trademarks or trade-
marks of Microsoft Corporation in the United
States and/or other countries.
Supplied accessories
SD card (in the unit) . . . . . . . . . . . . . . . . . . . 1
USB cable . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA battery. . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Owner’s Manual or Quick Start Guide . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . 1
•
•
•
•
•
•
Macintosh, Mac OS and Mac OS X are trademarks
of Apple Inc., registered in the U.S. and other
countries.
Other company names, product names and logos
in this document are the trademarks or registered
trademarks of their respective owners.
Please contact the store where you purchased this
unit if any of these accessories are missing or have
been damaged during transportation.
This product is designed to help you record and
reproduce sound works to which you own the
copyright, or where you have obtained permission
from the copyright holder or the rightful licensor.
Unless you own the copyright, or have obtained the
appropriate permission from the copyright holder or
the rightful licensor, your unauthorized recording,
reproduction or distribution thereof may result in
severe criminal penalties under copyright laws and
international copyright treaties. If you are uncertain
Trademarks
SD Logo is a trademark.
SDHC Logo is a trademark.
TASCAM DR-07 11
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
about your rights, contact your legal advisor. Under
no circumstances will TEAC Corporation be respon-
sible for the consequences of any illegal copying
performed using the DR-07.
About SD cards
Since this unit uses an SD card for recording and
playback, you must insert an SD card into the unit
before use. You can use 64 MB–2 GB SD cards
and 4 GB–32 GB SDHC cards with this unit.
MPEG Layer-3 audio coding technology licensed
from Fraunhofer IIS and Thomson.
Please see the TASCAM web site (www.tascam.
com) for information about cards that have been
tested with the DR-07.
Supply of this product does not convey a license
nor imply any right to distribute MPEG Layer-3
compliant content created with this product in
revenue-generating broadcast systems (terrestrial,
satellite, cable and/or other distribution channels),
streaming applications (via Internet, intranets
and/or other networks), other content distribution
systems (pay-audio or audio-on-demand applica-
tions and the like) or on physical media (compact
discs, digital versatile discs, semiconductor chips,
hard drives, memory cards and the like). An
independent license for such use is required. For
NOTE
When new, this unit comes with an SD card
inserted. This card can be used for recording
and playback as is. There is no need to reinsert
or format it.
12 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
Precautions for use
SD cards are delicate media. In order to avoid
damaging a card or the card slot, please take the
following precautions when handling them.
Do not leave them in extremely hot or cold
•
places.
Do not leave them in extremely humid places.
Do not let them get wet.
Do not put things on top of them or twist them.
Do not hit them.
•
•
•
•
Cleaning the unit
To clean the unit, wipe gently with a soft dry
cloth. Do not use any benzene, paint thinner, ethyl
alcohol or other chemical agents to clean the unit
as they could damage the surface.
TASCAM DR-07 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Preparation
Inserting the SD card
An SD card is used as recording media for
recording and playback.
Cards that comply with SD and SDHC stan-
dards can be used.
•
A list of SD cards that have been tested with
this unit can be found on the TASCAM web
•
The SD card slot and the USB connector are under
the cover on the left side of the unit. The SD card
is to be inserted in here.
NOTE
An SD card is pre-installed when the unit is new.
There is no need to reset this SD card before
using it to record or play files.
If you try to force the SD card in the wrong way,
the slot and the card could be damaged, so please
use caution.
1. Press the cover down in the direction of the
arrow to open it.
2. Insert the SD card in the SD card slot and
push it until it clicks fully into place.
3. Close the cover after inserting the card.
14 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Preparation
Removing the SD card
Inserting a new card
The following pop-up screen appears if you insert
a new card in the unit.
1. Make sure the unit power is off.
2. Press the inserted SD card in gently and it
will disengage from the unit so that you can
pull it out completely.
Press the ¥/π key to format the card so that it can
be used with this unit.
When formatting finishes, the Home Screen appears.
Other cases that require formatting
CAUTION
• The above “FORMAT ERROR” screen also
appears if you install an SD card that was for-
matted by a device other than the DR-07. Reformat
the card to use it with this unit.
Do not remove the SD card during recording or
playback, or when the unit is connected to the
computer by USB. Be sure to turn off the unit’s
power before removing the card.
TASCAM DR-07 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Preparation
Write-protected cards
CAUTION
Formatting an SD card erases all files that are
on it. Make certain that you have copied any
files that you want to save from the card before
formatting it.
SD cards have write-protect (lock) switches.
• The following pop-up screen appears if a system
file or other crucial file was accidentally erased
from the SD card when used with a computer
Unprotected
Protected
Files cannot be recorded or edited on a card if you
slide its switch down.
Slide the switch down if you want to prevent the
contents of the card from being changed or erased.
In either case, press ¥/π to reformat the card.
If a protected SD card is inserted, playback is
possible, but you will not be able to record or edit
files.
TIP
Always make backup copies of important files as
soon as you can.
16 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Preparation
Powering the unit
The DR-07 can be operated using two AA batteries
or an optional AC adapter (PS-P520). This unit can
use alkaline or Ni-MH batteries.
NOTE
When using batteries to power the unit, use the
BATTERY TYPE item on the SETUP screen to set
the type of batteries you are using (see “Select
the type of batteries” on page 77).
Installing the batteries
Slide the battery compartment cover on the back of
the unit to open it, and insert the two AA batteries
(supplied) observing the battery polarity (+ and –)
marked in the battery compartment.
NOTE
The included alkaline batteries are for confirm-
ing operation of the unit and might not last very
long.
TASCAM DR-07 17
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Preparation
Using an AC adapter (purchased
separately)
CAUTION
Use only the PS-P520 AC adapter. Using an
AC adapter other than the specified can
cause a malfunction, fire, or electric shock.
To use the PS-P520 AC adapter (sold separately),
connect the adapter to the unit and the adapter to
the power cord before plugging it into an outlet.
Turning the power on and off
To turn the power ON, press and hold the POWER
key on the left side panel until “TASCAM
DR-07” appears on the display.
The Home Screen appears when the unit starts up.
NOTE
When both batteries are installed and the AC
adapter is connected, power will be supplied
from the AC adapter.
Start-up screen
18 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Preparation
The power turns off after the unit completes its
shut down process.
CAUTION
Do not remove the batteries or disconnect
the power cable accidently while the unit
is operating. If you do so, the unit cannot
shut down properly and all unsaved data
will be lost. Lost data cannot be restored.
We recommend that you also save the data
manually often.
Home Screen
To turn off:
To turn the power OFF, press and hold the
POWER key until “PORTABLE DIGITAL
RECORDER” appears on the display.
Setting the date and time
Follow these procedures to set the date and time
of the built-in clock. When you create an audio
file, date and time information is included in the
file data.
1 Press the MENU key to open the Menu
Screen.
2 Use the wheel to select DATE/TIME
and press the ¥/π key to open the
TASCAM DR-07 19
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Preparation
Date/Time Screen.
NOTE
•
The contents of date and time settings last
only several minutes if the power is not
supplied by batteries or an AC adapter. We
recommend that you replace the batteries
before they deplete completely when you
power the unit only by the batteries.
•
•
We also recommend that you install batter-
ies even you are using an AC adapter. The
setting can be retained by this even the AC
adapter is disconnected.
If the setting is reset, make the setting again.
The clock stops while this screen is displayed.
3 Use the µ and ≤ keys to move the
cursor (the part highlighted in inverse)
and use the wheel to set the values.
4 After making the setting, press the ¥/π
key to restart the clock from the newly
set value.
The display returns to the Menu Screen.
20 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Part Names and Functions
Top panel
1 Built-in stereo microphone
To use this stereo electret condenser
microphone as the input source, select “MIC”
on the Input Setting screen. If you connect an
external microphone to the MIC IN jack on the
rear panel, the built-in microphone becomes
inactive.
2 Display
In addition to the Home Screen, this shows
the recording screen, various setting screens,
and other operation information. (See “Screen
Overview” on page 29.)
3 I/O LOOP key
Use this key to set the IN (start) and OUT
(end) points, and playback the interval (loop
playback). Also, use this key to cancel the
loop playback. (See “Loop playback” on page
73.)
22 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Part Names and Functions
When a setting screen is open, press to return
to the Home Screen.
4 µ key
Press this key to return to the beginning of a
track that is playing or stopped in the middle.
On a setting screen, use this key to respond
“NO” to a confirmation message.
If you press this key when a track is stopped
at its beginning, the unit will skip to the
beginning of the previous track.
7 PB CONT key
Press and hold this key to open the Playback
Control (PB CONTROL) Screen. When the
Playback Control Screen is open, press and
hold this key to return to the Home Screen.
(See “Special playback control functions” on
page 71.)
Press and hold this key to search backwards.
On the setting screens, use this key to move
the cursor left. On the Browse Screen, press
this key to move up a level.
5 MENU key
Briefly press this key to turn the speed control
that is set on the Playback Control Screen
(VSA and/or SPEED) ON and OFF. When
When the Home Screen is displayed, press
this key to open the Menu Screen.
Press this key to return to the Menu Screen
from the various setting screens.
ON, the
icon appears at the top of
the Home Screen as light letters on a dark
background.
When the Menu Screen is displayed, press this
key to return to the Home Screen.
6 STOP/HOME key
8 ≤ key
Press this key during playback or when
playback is stopped to skip to beginning of the
next track.
Press this key to stop recording and playback
or to end recording standby.
Press and hold this key to search forward.
TASCAM DR-07 23
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Part Names and Functions
On the setting screens, use this key to move
the cursor right.
0 PEAK indicator
This lights when the selected input signal
exceeds the maximum level.
On the Browse Screen, press this key to move
down a level.
q Wheel
NOTE
When a setting screen is open, use the Wheel
to change the setting of the selected item.
Keys 6 and 7 may not work for all VBR
(Variable Bit Rate) MP3 files. For some VBR MP3
files, operating these keys may cause the sound
to be not synchronized with the elapsed time
shown on the display and the end parts of the
file being played back may be repeated at the
end of the track. In this case, stop playback to
return to normal operation.
When the Home Screen is open, use the wheel
to adjust the file playback position.
w ¥/π key
When the Home Screen is displayed and
playback is stopped, press this key to start
playback. During playback, press this key to
stop playback at the current position.
9 RECORD key
When playback is stopped, press this key to
put the unit into recording standby. When in
standby, this key flashes.
When using a setting screen, use this key,
for example, to confirm a selection, advance
a level in a menu and answer “YES” to a
confirmation message
When in recording standby, press this key
to start recording. The key lights while
recording.
When recording, press this key to pause
recording.
24 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Part Names and Functions
y
/LINE OUT jack
Right side panel
Use this to connect with headphones or the
line input jack of an amp or other equipment.
During recording or recording standby, this
outputs the input signals and in other cases,
this outputs the playback signal.
e LINE IN jack
Use this stereo mini-jack for line input.
r OUTPUT LEVEL (+, –) keys
Use these keys to adjust the signal level output
from the /LINE OUT jack. The volume level
appears on the display during adjustment.
t REC LEVEL volume
Use this to adjust the input signal level of the
built-in microphone, the MIC IN jack and the
LINE IN jack.
TASCAM DR-07 25
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Part Names and Functions
Left side panel
[When the card slot cover opened]
a SD card slot
u DC
IN 5V jack
Connect a TASCAM PS-P520 AC adapter
(purchased separately) to this jack. Do not
connect other adapters.
Insert an SD card into this slot. (See “About
SD cards” on page 12.)
s USB port
i SD card slot lid
Use the included USB cable to connect with a
computer USB port. (See “Connecting with a
computer” on page 41.)
o POWER key
Press and hold this key to turn the unit’s
power ON and OFF.
CAUTION
p HOLD switch
Please connect the unit directly to a
computer without using a USB hub.
Slide this to the left to turn the hold function
ON. All keys are inoperative when hold is ON.
26 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Part Names and Functions
Rear Panel
Bottom panel
d MIC IN jack
Use this input jack to connect a stereo
mini-jack microphone. This jack provides
plug-in power when set to do so on the
Input Setting Screen.
NOTE
•
•
We call this the Rear Panel because this is the
end that faces away from the operator of the
unit when placed on a table with the built-in
mic (this end) facing the sound source.
Connecting a mic to the MIC IN connector
disables the built-in mics.
f Battery compartment cover
TASCAM DR-07 27
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Part Names and Functions
g Tripod screw socket (1/4 inch)
This unit can be attached to a tripod or a mic
stand.
CAUTION
•
•
Always tighten all the screws on the tripod
or the mic stand to avoid the risk of the unit
falling and being damaged.
When using this unit while attached to a
tripod or a mic stand, place the tripod or mic
stand on a flat surface.
h Battery compartment
This holds two AA batteries.
[When the battery compartment cover removed]
28 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
The display of the unit shows various screens.
Home Screen
When the unit is ordinarily playing or stopped,
the Home Screen appears on the display.
The Record Screen appears when the unit is
recording or in recording standby.
Setting screens appear when making various
settings.
•
•
•
The items that appear on the Home Screen
are explained below. See the explanations later
in this chapter for the setting screens and the
Record Screen.
The following sections provide an overview of the
appearance and operation of the Home Screen and
the record screen, as well as an overview of the
screens for various settings.
1 Status of playback control function settings
These show whether the various playback
control functions (speed control and key
change) are currently active. When they are
active, their icons appear as light letters on a
TASCAM DR-07 29
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
dark background (
,
). (See “Special
When using the AC adapter (sold separately)
appears.
Playback Control Functions” on page 71.)
2 Loop/repeat setting status
4 Unit status
The following icons appear depending on the
current loop/repeat setting.
The following icons appear to show the
current operation status.
¥
Track playing
Single playback
π
File stopped in progress (paused)
File stopped at its beginning
Fast forwarding
Repeat playback of 1 track
·
Repeat playback of all tracks
in the play area
˚
∆
Loop repeat active
Fast rewinding
3 Power status display
≤ Skipping to the beginning of the
When batteries are being used a battery icon
appears. The icon blinks when it is necessary
to change the batteries. The icon shows the
approximate amount of remaining battery
next track
µ Skipping to the beginning of the
current or previous track
5 Level meter
power (
,
,
) with more bars indicating
more power.
This shows the level of the selected input
signal during recording and recording pause,
and the level of the playback signal in other
cases.
When the battery power is almost gone, the
icon blinks, warning that the power is
about to turn OFF.
If the input level exceeds the maximum
30 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
Shows the elapsed time (hours: minutes:
seconds) of the currently playing track.
allowable level, a dot is lit at the right end
of the level meter.
6 File information
9 Remaining time
The tag information or file name of the
currently playing track is shown. If an MP3
file has ID3 tag information, the ID3 tag
information is given priority. The file name is
shown for WAV files and for MP3 files that do
not have ID3 tag information.
Shows the remaining playback time of the
current track (hours: minutes: seconds).
0 dB display
Shows the value of the maximum level in dB
during each time interval.
q Status of loop IN and OUT points
This shows the status of the IN and OUT
point settings for loop playback.
NOTE
ID3 tag information includes the title, artist
name and other information that can be saved
in an MP3 file.
If an IN point is set, the icon appears under
the display bar at the position equivalent to the
playback location.
7 Selected playback area
If an OUT point is set, the icon appears
under the display bar at the position equivalent
to the playback location.
Shows the currently selected playback area.
ALL
All files in the Music Folder
w Playback file number/total number of files
FOLDER
All files in the selected sub-
folder of the Music Folder
The total number of files in the selected
playback area and the number of the current
file are shown.
P.LIST
Files added to the playlist
8 Elapsed time
TASCAM DR-07 31
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
e Playback position display bar
Record Screen
This bar shows the current playback position.
The bar darkens from the left as playback
proceeds.
This screen opens when you press the RECORD
key to start recording standby mode and stays open
when you press the RECORD key again to start
recording.
This status of the power and the effect use appears
the same as on the Home Screen. This screen also
shows the following.
32 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
1 MIC input setting status
7 Elapsed recording time
Shows the status of settings related to the
built-in microphone and MIC IN jack on the
rear panel (stereo recording, plug-in power,
low cut filter and level control).
The elapsed recording time of the track
appears as hours: minutes: seconds.
During recording standby, the maximum
remaining recording time appears.
2 Pre-recording setting status
PREappears when pre-recording is set.
3 Recorder operation
8 Remaining recording time
The remaining recording time appears in
hours: minutes: seconds.
9 dB display
º
π
ª
Recording
Shows the value of the maximum level in dB
during each time interval.
Recording paused
Recording stopped
0 Record mode
4 Record level meter
Shows the recording file type and sampling
frequency.
The input signal level of the selected input
appears as separate L and R channels.
5 File name
Shows the file name that is automatically
assigned to the file being recorded.
6 Input selection
Shows the input source.
TASCAM DR-07 33
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
Setting Screens
Use this unit’s various setting screens to make
various settings, conduct operations and show
information.
NOTE
Although the various setting screens are
also used to execute functions and display
information, for example, in addition to
making settings, we call them “setting screens”
in this manual.
Setting screen structure
Most of the setting screens are accessed by first
pressing the MENU button to open the Menu
Screen, but some screens can also be accessed
directly using dedicated keys.
The following table provides an overview of the
setting screens.
34 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
Screen
Overview
Access method
View file information, system setting information,
and system information
INFORMATION
View music files and sub-folders in the Music
Folder, play and erase files, add files to the playlist,
create and select folders
BROWSE
PLAYLIST
Edit the playlist (erase and move tracks in it)
Set playback mode
Set single or repeat mode
PLAY MODE
Press the MENU key to open
the Menu Screen and select
the desired setting screen
Select input source, make built-in microphone and
MIC IN settings
Make settings related to recording
(file type, sampling frequency, maximum file size)
Turn pre-recording and recording delay functions
ON and OFF
INPUT SETTING
REC SETTING
DIVIDE
SETUP
Divide files
Make various system settings
Initialize and format the SD card
Set the date and time of the built-in clock
Set playback control function settings
DATE/TIME
PLAYBACK
CONTROL
Press and hold the PB CONT
key
TASCAM DR-07 35
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
Operation basics
When the Menu Screen is open, press this
key to return to the Home Screen. When the
Record Screen is open, press this key to open
the menu of the Input Setting screen.
Use the MENU, STOP/HOME, ¥/π, µ and ≤
keys and the wheel to conduct most operations on
the various setting screens.
You can also make settings for items other
than INPUTon the Input Setting screen.
The keys have the following functions.
Wheel
Use the wheel to change the value of the
selected item.
¥/π key
Press this key to make an item selection and
to answer “YES” to a confirmation message.
(This functions like the “ENTER” key on a
computer).
µ key
When a setting screen is open, moves the
cursor (part highlighted in inverse) to the left
within the screen. Use this after setting the
value of an item to return to item selection,
for example.
MENU key
Press this key to open the Menu Screen
(except when the Menu Screen is already
open or the Record screen is open).
36 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
≤ key
When a setting screen is open, moves the
Operation example
cursor (part highlighted in inverse) to the right
within the screen. In many cases, the ¥/π
key can also be used this way.
In this example, we will use the CUE/REV
SPEEDitem in the Setup Screen to change the
forward/reverse search speed.
STOP/HOME key:
1 When the Home Screen is displayed, press
When a setting screen is open, press to return
to the Home Screen. Press this key to answer
“NO” to a confirmation message.
the MENU key to open the Menu Screen.
TIP
You can also use menus during playback
2 Turn the wheel to select SETUP(highlighted
in inverse), and press the ¥/π key to open
the Setup Screen.
3 Turn the wheel to select the CUE/REV
SPEEDitem, and press the ¥/π key to
TASCAM DR-07 37
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Screen Overview
show the current setting value (the factory
setting is “X8”) highlighted in inverse.
NOTE
•
•
When the ¶ icon appears in the lower right
part of the screen, as shown in the preceding
image, there is additional information for the
current screen below what is shown on the
display.
4 Turn the wheel to select the desired setting.
The setting is changed immediately, so there
is no need to press the ¥/π key again to
confirm it.
When the § icon appears, there is additional
information for the current screen above
what is shown on the display.
5 Press STOP/HOME to return to the Home
Screen.
•
•
You can also use the ≤ key instead of the
¥/π key in these steps.
When the § icon appears to the right of a
setting value, you can change that value by
turning the wheel to the right. When the ¶
icon appears to the right of a setting value,
you can change that value by turning the
wheel to the left.
38 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Making Connections
Connecting to the MIC IN jack
Connecting mics and other
audio devices
You can connect a one-point stereo electret con-
denser microphone, for example, to the MIC IN
This unit has a built-in stereo microphone that
you can use to practice or record your singing, for
example, but you can also use an external mic or
other device as an input. You can connect external
sound sources to the line input jack or the micro-
phone input jacks. The following sections explain
how to use the jacks to connect external devices.
(See “Selecting the input source” on page 49 for
more about making settings related to connections
and input level setting.)
jack (stereo mini-jack) on the rear panel. Use the
Input Setting Screen to adjust the level control, the
low cut filter and other settings. (See “Selecting the
input source” on page 49.)
TASCAM DR-07 39
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Making Connections
Connecting to the LINE IN jack
Connecting monitors
You can connect the line output of an audio device,
for example, to the LINE IN jack (stereo mini-jack)
on the right side panel.
Connect headphones, speakers with built-in
amplifiers, an amp and speaker system or other
monitoring system to the DR-07 /LINE OUT jack.
NOTE
The auto gain function and stereo/mono switch-
ing cannot be applied to a signal input through
the LINE IN.
40 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Making Connections
Connecting with a computer
CAUTION
The unit cannot be used when connected
with a computer by USB.
By connecting this unit with a computer, you can
copy WAV or MP3 music files from the computer
to this unit. From the computer you can also erase
files on this unit and manipulate folders.
When connected, “USB connected” appears
on the DR-07 screen.
To connect to a computer, opent the lid on the
left side of the unit, use the included USB cable
to connect the USB port of the DR-07 and the
computer.
The recorder appears on the computer screen as an
external drive named “DR-07.”
NOTE
When shipped from the factory the “DR-07”
drive contains the “MUSIC” and “UTILITY”
folders, as well as the “MANUAL” folder, which
contains a PDF copy of this Owner’s Manual.
TASCAM DR-07 41
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Making Connections
Disconnecting from a computer
To end the USB connection, first follow the
procedures for your computer to disconnect the
DR-07 and then remove the USB cable. The
DR-07 automatically restarts.
See the computer manual for how to close the
connection on the computer.
42 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
6–Copying Tracks from a Computer
You can transfer audio files from a computer by
USB to this unit for playback.
Copying audio files from a
computer
This unit can handle MP3 (32–320 kbps, 44.1/48
kHz) and WAV (44.1/48 kHz, 16/24-bit) audio
file types.
1 Connect the DR-07 to a computer (See
“Connecting with a computer” on page 35).
2 Click the DR-07 drive on your computer
to see its contents, including the UTILITY,
MUSIC and MANUAL folders.
Preparing audio files on a computer
Use the abilities of your computer OS or a software
application to copy tracks from a CD or other
source to your computer.
3 Drag-and-drop audio files from your
computer to the Music Folder to copy them
to the SD Card in the DR-07.
When copying files to you computer, choose file
types that the DR-07 can handle (the types of
MP3s and WAV files listed above).
4 After you finish copying files and ending the
connection with the DR-07 on the computer,
disconnect the USB cable (or remove the
SD card if it is connected directly to the
computer).
TIP
You can also prepare your own tracks using
digital audio software, or use tracks you previ-
ously recorded with the DR-07 or another
device.
See the computer manual for how to close
the connection on the computer.
The DR-07 automatically restarts after it
has been disconnected.
TASCAM DR-07 43
Download from Www.Somanuals.com. All Manuals Search And Download.
6–Copying Tracks from a Computer
NOTE
Managing the Music Folder from a
computer
Instead of using USB to connect the DR-07 and
a computer, you can also conduct the same
operations by removing the SD card from the
DR-07 and connecting it directly to a computer
that has a built-in SD card slot or by using a card
reader.
You can manage the contents of the Music Folder
on an SD Card in the DR-07 from a computer.
You can create up two levels of sub-folders inside
the Music Folder. The DR-07 does not recognize
folders and audio files at or below the third sub-
level.
TIP
You can use more than one SD card with the
DR-07. Make certain that you format additional
cards by inserting them in the DR-07 and
following the instructions about formatting
(see Formatting the SD card on page 75.) before
you copy files from your computer.
Since you can set the DR-07 to only play the
contents of a specific folder, you can organize
tracks into genres, artists or other categories as you
like. (See “Folder operations” on page 62.)
Since all storage media, including SD cards, can
fail, it is a good idea to make back-up copies of
your recordings on your computer hard drive,
CD-Rs or other media.
• If you name the sub-folders and music tracks,
these names will appear on the screen of this unit.
44 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
7–Playback
When the Home Screen is displayed, use the
¥/π, µ and ≤ keys to operate the DR-07
as you would with an ordinary CD player or
other audio device.
Stop playback
During playback, press the STOP/HOME or
¥/π key to stop (or pause) it at the current
position.
Use the wheel to change the playback position.
NOTE
Selecting tracks
•
•
When the Home Screen is not displayed,
these keys and the wheel have different
functions.
Use the µ and ≤ keys to select tracks both
during playing and when playback is stopped.
SD Cards formatted by a TASCAM DR-1 or
GT-R1 can also be used.
During playback or when a track is stopped in
the middle, press the µ key to return to the
beginning of the current track.
Starting and stopping playback
When stopped at the beginning of a track, press the
µ key to skip to the beginning of the previous
track, or press the ≤ key to skip to the beginning
of the next track.
Play a track
When playback is stopped, press the ¥/π key
to start playback.
NOTE
•
Only files in the playback area that is
currently set can be selected for playback.
(See “Setting the playback area” on page 54.)
TASCAM DR-07 45
Download from Www.Somanuals.com. All Manuals Search And Download.
7–Playback
•
The track name, file number and other file
information for the currently playing track
appear on the display.
Using the wheel to change the
playback position
•
The ·icon appears on the display when
playback is stopped at the beginning of a
track, and the π icon appears when playback
is stopped in the middle of a track (paused).
You can use the wheel to adjust the playback
position within a track. When you turn the wheel,
the position in the playback position display bar
changes, so you can visually confirm that the
playback position has been moved.
Moreover, the faster the wheel is turned the more
the position is changed.
Search forward and backward
Press and hold the µ key to search backwards
or the ≤ key to search forwards.
NOTE
Use the CUE/REV SPEEDitem on the
Setup Screen to change the search speed.
(See “Making system settings” on page 74.)
NOTE
No sound is output while you turn the wheel.
46 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
In addition to using the built-in microphone, you
can record using an external microphone or record
the output signal from a mixer or other audio
source. You can select among MP3 (44.1/48 kHz,
32–320 kbps) and WAV (44.1/48 kHz, 16/24-bit)
audio recording formats.
Selecting the file type and sampling
frequency
3 Use the FORMATitem to select the file type
from the following options: WAV at 16-bit
(factory setting) or 24-bit, or MP3 at 32
kbps, 64 kbps, 96 kbps, 128 kbps, 192 kbps,
256 kbps, or 320 kbps.
Select the audio file type that you want to record
before you start recording.
1 Press the MENU key to open the Menu
4 Use the SAMPLEitem to select a sampling
frequency of 44.1 kHz (factory setting) or
48 kHz.
Screen.
2 Select the REC SETTINGitem to open the
NOTE
Recording Settings Screen.
For other special recording functions, see
"Special functions during recording" on page
55.
48 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
TIP
Selecting the input source
•
WAV files do not use data compression and
are truer to the character of the sound, but
they use much memory. Since MP3 files use
data compression, they do not use nearly as
much memory. For example, ordinary audio
CD tracks are 16-bit, 44.1 kHz WAV files. A
3.5–minute CD track uses about 35 MB of
space when copied to a hard drive. The same
track converted to a 128 kbps MP3 file uses
only about 3.2 MB.
Follow these procedures to select the input source.
1 Press the MENU key and select INPUT
SETTINGitem, then press the ¥/π key to
open the Input Setting Screen.
•
If you are making a recording that you intend
to use in the production of a CD, it is a good
idea to record WAV files. If you have enough
space, 24-bit recording gives you extra head
room, allowing you to capture a greater
dynamic range. When recording rehearsals,
lectures and songwriting ideas, for example,
and higher quality audio is not as important
as smaller file size, MP3 may be a better
choice. There are many excellent books (and
resources on the Internet) about digital
recording if you want to learn more about
these formats.
2 Use the INPUTitem to select one of the
following input sources.
TASCAM DR-07 49
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
MIC
NOTE
The input source is the recording source when
recording.
Sets the input source as the built-in microphone
when no microphone cable is connected to the MIC
IN jack (stereo mini-jack). When a microphone
cable is connected to the MIC IN jack, the input
microphone signal becomes the input source.
Setting the MIC input functions
If you select MIC, you should also set the
input functions. (See “Setting the MIC input func-
tions” below.)
After selecting MICas the INPUTitem, press the
µ key to highlight INPUT, then turn the wheel
right to open the MICInput Setting screen.
LINE
Sets the source as the line level signal input to the
right side panel LINE IN jack (stereo mini-jack).
CAUTION
Use headphones to monitor when you are
recording with a microphone. If you use
speakers to monitor, the sound output from
the speakers may also be recorded, causing a
poor recording and even feedback.
This screen has the following settings. Among
these, POWER, is only effective to MIC IN. All the
50 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
plug-in power may damage such microphones.
other items affect both the built-in microphone and
MIC IN.
LOW CUT
GAIN
The factory default setting of the low cut filter is
Set the input sensitivity as HIGH, MID, or LOW
.
OFF, but you can also select 40HZ, 80Hzor
The factory default setting is MID. Change it to
120Hzas the cut-off frequency for a low cut filter.
HIGHif the input level is too low.
TIP
Try using one of the low cut filter settings when
recording outdoors or another place where the
unwanted sound of wind is being recorded.
TYPE
Select STEREOor MONOaccording to the type
of connected microphone. The factory setting is
STEREO. If you select MONO, a mixed signal of
the left and right input signals is provided to the
left and right channels respectively.
LEVEL CTRL
Use this to set the level control function.
Set it to AUTOto have the DR-07 automatically
adjust the input gain according to the input level.
Loud sounds and quiet sounds are both adjusted
to the same level.
POWER
When connecting an external microphone that
requires plug-in power set this to ON. The factory
default is OFF
Set it to LMTto have the DR-07 automatically
limit the input gain so that input level of loud
sounds are reduced to prevent distortion.
.
CAUTION
Set this to OFFwhen using the built-in mic or
connecting a dynamic microphone or micro-
phone with a built-in battery. If set to ON, the
The factory default setting is OFF
.
TASCAM DR-07 51
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
ST
NOTE
When recording live performances and in other
situations where unexpected loud sounds might
occur, set this function to LMTto prevent input
clipping and allow recording without distortion.
When TYPEis set to STEREO, the
appears as light letters on a dark background.
icon
PWR
When POWERis ON, the
icon appears as
light letters on a dark background.
Display of input functions on the
Record Screen
LCF
When LOW CUTis set to 40Hz, 80Hzor
Icons appear on the Record Screen to show the
status of the TYPE, POWER, LOW CUTand
LEVEL CTRLsettings.
120Hz, the
icon appears as light letters
on a dark background.
LMT
When LEVEL CTRLis set to AUTOor LMT
,
the
icon appears as light letters on a dark
background.
Adjusting the input recording levels
You can adjust the recording level.
52 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
The following procedures explain how to use the
Record Screen to set the levels.
1 Press the RECORD key to begin recording
standby. The key flashes red and the Record
Screen appears. The input signal is output
from the
/
LINE OUT
jack.
The L/R meter shows the input level. If the input is
too high, a line remains at the right end of the level
meter and the PEAK indicator to the left of the
RECORD key lights.
Set the level as high as possible without causing
the PEAK indicator to light when the loudest
sounds occur.
2 Use the REC LEVEL volume control on the
right side of the unit to adjust the input
level.
• When you have selected MICas the input source
and are using the built-in microphone or MIC IN
jack, if you find the level to be too low even when
the REC LEVEL volume is at maximum, use the
MIC Input Setting Screen to set the GAINitem to
TASCAM DR-07 53
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
MIDor HIGH. (See “Setting the MIC input func-
tions” on page 50.)
Recording
Before starting the following operation procedures,
input selection and level adjustment should be
completed, and the Home Screen should be open.
TIP
•
•
•
In addition to adjusting the REC LEVEL
volume, try changing the distance and angle
between the microphone and the sound
source.
1 Press RECORD to begin recording standby.
To record the sound of a source most effec-
tively and accurately, point the front of the
DR-07’s built-in mics toward the sound source
with the LCD facing up.
An easy way to set the input level is to raise
it until the PEAK indicator lights while
inputting as loud a noise as you expect to
record. When the PEAK indicator lights,
lower the input level until it no longer lights.
NOTE
The screen shows the recording file name,
the input source, the recording audio
file type and sampling frequency. Please
confirm that these are as desired before
starting recording.
Press STOP/HOME to end recording standby.
54 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
audio file up to the moment that you paused
recording is created.
2 To start recording, press the RECORD key
again.
Special functions during recording
Track incrementing
Incrementing the track number manually
During recording, you can create a new file that
has a number at the end of its file name that is one
higher (incremented) and continue recording.
When recording starts, the RECORD
key lights continuously, and the display
shows the elapsed recording time and the
remaining recording time.
1 Press the ≤ key during recording to
create a new file with the number at the end
of the file name incremented (increased)
and continue recording in this file from its
beginning (00:00:00).
3 Press the STOP/HOME key to end recording
and create the audio file.
•
To pause recording, press the RECORD
key. Press the RECORD key again to restart
recording in the same track. If you press the
STOP/HOME key after pausing, a recorded
You can increment even when paused.
TASCAM DR-07 55
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
CAUTION
• You cannot increment if the total
number of files would exceed 999.
• You cannot increment when the current
file is only two seconds or shorter.
• When incrementing, if a file already
exists with the incremented file name,
the number will be increased again to
create a new unique file name.
2 Use the SIZE item to select the file size for
automatic incrementing.
Options: 64M, 128M, 256M, 512M, 1G, 2GB
(default setting)
Automatic track incrementing according to
file size
When a file reaches a designated size during
recording, you can set the unit to automatically
create a new file with an incremented file name and
continue recording.
CAUTION
You cannot increment if the total number
of files would exceed 999.
NOTE
1 Press the MENU key to open the menu list
screen. Select REC SETTINGand press the
≤ key to open the Rec Setting screen.
The recording time differs for the same file
size depending on the file format. Moreover,
23:59:59 appears if the recording time is 24
hours or more.
56 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
Pre-recording
CAUTION
• If the unit has been in recording
standby for less than two seconds, only
the amount of time that the unit has
been in standby will be included
When the unit is in recording standby, the unit can
record the two seconds before the start of recording
and include it in the recording.
Use the following procedures to set pre-recording.
• Pre-recording is not possible if the
remaining space on the SD card is three
seconds or less.
1. Press the MENU key to open the menu list
screen. Select REC SETTINGand press
the Á/π key to open the REC SETTING
screen.
Recording delay
This function allows the start of recording from the
time of pressing the RECORD key to be delayed 10
ms (this time is fixed).
This is convenient if you want to avoid recording
the sound of the RECORD key being pushed.
1 Press the MENU key to open the menu list
screen. Select REC SETTINGand press
the Á/π key to open the REC SETTING
screen.
2 Use the PRE RECitem to turn pre-record-
ing ON or OFF.
Options: ON, OFF (default setting)
TASCAM DR-07 57
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
2 Use the DELAY item to turn recording delay
ON or OFF.
2 Use the wheel to locate the point where you
want to divide the file.
Options: ON, OFF(default setting)
NOTE
•
•
You can press the PLAY key and select the
point where you want to divide the file
during playback.
File divide function
You can also press the REW key to move
the location towards the beginning of the
recording or the FWD key to move the loca-
tion towards the end of the recording. You
cannot divide a track at its beginning or end.
You can divide one file into two at the time of your
choice. For example, you can divide a large file or
multiple songs into several consecutive files or use
this function to erase unnecessary recordings.
1 Press the MENU key to open the menu list
screen. Select DIVIDEand press the Á/π
key to open the DIVIDE screen
58 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Recording
This function cannot be used if the remaining
space on the SD card is low.
Press the RECORD key to open a confir-
mation screen and press the Á/π key to
confirm.
•
CAUTION
• You cannot divide a file if the resulting
file names would be 200 or more char-
acters long.
• You cannot divide a file if a resulting file
name would be the same as the name of
an already existing file.
The file is divided and the Home Screen
reopens.
NOTE
•
When a file is divided, the two files that are
created are given the same file name with
the suffixes “_a” and “_b” at the ends of
their names. If you further divide a file that
already has an “_a” at the end of its file
name, the split files will have the suffixes
“_a_a” and “_a_b”.
TASCAM DR-07 59
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Playback Area and Playlist
On the Home Screen, you can use the µ and
Setting the playback area
≤ keys to select the playback track. The files
that you can select are determined by the playback
area setting.
Use the following procedures to select the
playback area on the Play Mode Screen.
1 Press the MENU key to open the Menu
Screen and select PLAY MODE. Press the
¥/π key to open the Play Mode Screen.
Limiting the playback area makes track selection
easier when you have numerous recorded and
copied tracks on the SD card.
On the Play Mode Screen, you can select all files,
the current folder or the playlist as the playback
area. You can also use the Browse Screen to set a
folder as the playback area.
TIP
On the Browse Screen, regardless of the
playback area setting, you can select any file
on the card that you want.
2 Select the AREAitem and press ¥/π.
3 Set the playback area to one of the following
options.
60 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Playback Area and Playlist
If there is no playlist defined, a “No PLAYLIST”
pop-up appears.
NOTE
The current playback area setting appears in
the lower left of the Home Screen.
Selecting a folder for the playback
area
Regardless of the current playback area, if you
select a folder on the Browse Screen, the playback
area changes to the selected folder.
1. Press the MENU key to open the Menu
Screen, and select the BROWSEitem. Press
the ¥/π key to open the Browse Screen.
ALL
Set the playback area as all files in the Music
Folder on the SD card.
FOLDER
Set the playback area as all the files in the currently
selected folder.
PLAYLIST
Set the playback area as the tracks in the playlist.
(See “Playlist” on page 63.)
TASCAM DR-07 61
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Playback Area and Playlist
2 Select the desired folder.
Selecting a file to set the playback
area
For an explanation of how to use the Browse
Screen, see “Screen navigation” on page 67.
When the playback area is set to FOLDER, if you
select a file on the Browse Screen, the folder that
contains the selected file becomes the playback
area.
3 Press the ¥/π key to open the following
pop-up window.
1 Press the MENU key to open the Menu
Screen and select the BROWSEitem. Press
the ¥/π key to open the Browse Screen.
4 Select the SELECTitem and press ¥/π.
The display returns to the Home Screen, and
the first file in the folder is selected. This
folder becomes the playback area regardless
of the previous playback area setting.
62 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Playback Area and Playlist
2 Select the file you want.
Playlist
For an explanation of how to use the Browse
You can make a list of tracks for playback
(playlist). On the Play Mode Screen if you select
PLAYLISTfor the AREAitem, you can set
playback to just the tracks in your playlist.
Screen, see “Screen navigation” on page 67.
3 Press the ¥/π key to open the following
pop-up window.
Adding tracks to the playlist
1 Press the MENU key to open the Menu
Screen. Select the BROWSEitem and press
the ¥/π key to open the Browse Screen.
4 Select the PLAYitem and press ¥/π.
The display returns to the Home Screen,
and the selected track starts playing. In
addition, the folder that contains this track
becomes the playback area regardless of the
playback area folder set previously.
TASCAM DR-07 63
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Playback Area and Playlist
2 Select a track that you want to add to the
Screen and how to select tracks, see “Screen
navigation” on page 67.
playlist and press the ¥/π key.
A pop-up window appears.
Editing the playlist
You can view and edit the playlist you have made
on the Playlist Screen.
You can also use this screen to play tracks and to
edit the playlist.
1 Press the MENU key to open the Menu
Screen. Select PLAYLISTand press the
¥/π key to open the Playlist Screen.
3 Select ADD LISTand press the ¥/π key.
The track is added to the playlist and the
popup window closes.
4 Repeat steps 2 and 3 as necessary to add
more tracks to the playlist. The tracks are
numbered in the order that they are added.
NOTE
For an explanation of how to use the Browse
64 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Playback Area and Playlist
2 Select the file that you want to edit and press
For this operation, it does not matter which track
you select in step 2. All the files are removed
from the playlist, but they are not erased from
the SD card.
the ¥/π key to open a pop-up window.
DELETE
Remove the selected track from the playlist.
The file is removed from the playlist, but it is not
erased from the SD card.
Use the wheel to select the item you want
and press the ¥/π key. Their functions are
as shown below.
MOVE
Select this to change the order of tracks in the
playlist.
PLAY
In addition to the file name, the track number also
Play the file and return to the Home Screen.
appears highlighted in inverse.
In step 2, use the wheel to move the track to a
different position in the playlist.
ALL CLR
A confirmation message appears to confirm that
you want to remove all the files from the playlist.
Press the ¥/π key to remove all the files or the
STOP/HOME key to cancel this operation.
TASCAM DR-07 65
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Playback Area and Playlist
In the above example, the 4th track has been
moved to the 3rd track position.
3 Press the ¥/π key to complete the move and
return to the ordinary Playlist Screen.
66 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Browse Screen
TIP
If you connect the DR-07 with a computer by
USB, or mount the SD card on a computer using
a card reader or other input, you can change
the folder structure within the Music Folder and
erase files from the computer as you would the
contents of a hard drive. Furthermore, you can
change file names from the computer.
On the Browse Screen, you can view the contents
of the Music Folder, which contains the audio files
on the SD card that you can use with the DR-07.
On this screen, you can also play and erase selected
audio files, create folders, add tracks to the playlist
and so on. (See “Playlist” on page 63.)
To open the Browse Screen, press the MENU key
to open the Menu Screen. Select BROWSEand
press the ¥/π key.
Screen navigation
On the Browse Screen, folders and music files
appear in a hierarchical structure much like they
would appear on a computer. On the DR-07,
folders can only be used to two levels.
Use the wheel to select files and folders.
When a folder is selected, press the ≤ key to
show the contents of that folder.
•
•
When a file or folder is selected, press the µ
•
The contents of the folder that contains the file
that was selected on the Home Screen before the
Browse Screen was opened appears on the display.
key to exit the currently open folder and go to a
higher level in the folder structure.
TASCAM DR-07 67
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Browse Screen
Icons on the BROWSE screen
File operations
The meanings of icons that appear on the Browse
Screen are as follows.
Select the desired audio file on the Browse Screen
and press the ¥/π key to open the pop-up window
that is shown below.
Root Music Folder
The Music Folder is the highest (root) level folder
in the hierarchy shown on the Browse Screen.
Audio file
This icon appears before the names of music files.
Plus folder
This icon shows folders that contain subfolders.
Plain folder
Use the wheel to select the item you want from the
following list and press ¥/π to execute it.
This icon shows folders that do not contain
subfolders.
PLAY
Open folder
Plays the file. The display returns to the Home
Screen. If the playback area is set to FOLDER, the
playback area becomes the folder that contains the
playing file.
The contents of the folder marked with this icon
currently appear on this screen.
68 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Browse Screen
INFO
NOTE
When the BROWSE screen is open and an audio
file is selected, pressing the µ key causes the
folder that contains the file to be selected (go
up a level).
Displays the information of the selected file.
ADD LIST
Adds the selected file to the playlist. (See
“Playlist” on page 63.)
DELETE
A message appears to confirm that you want to
delete the file. Press the ¥/π key to erase the
file and the STOP/HOME key to cancel the
deletion operation.
CANCEL
No operation is conducted and the selected file is
left as is.
Use the wheel to select the item you want from the
following list and press ¥/π to execute it.
SELECT
Folder operations
Returns to the Home Screen and selects the first
file in the folder. This folder becomes the new
playback area regardless of the previous playback
Select the desired folder on the Browse Screen and
press the ¥/π key to open the pop-up window
that is shown below.
TASCAM DR-07 69
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Browse Screen
area setting. When recording, files are created in
this folder.
CREATE
A pop-up appears to confirm that you want to
create a new folder. Press the ¥/π key to create a
new folder, or press the STOP/HOME key to cancel
the operation.
However, if you try to create a new folder inside
a second level subfolder the message, “Layer
too deep” appears and the folder is not made.
ALLDEL
All files in the selected folder are deleted but sub-
folders are not deleted. Also, read-only files are not
deleted. Furthermore, files which are not recog-
nized by the DR-07 are left as they are.
CANCEL
No operation is conducted and the selected folder
is left as is.
70 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
11–Special Playback Control Functions
Not only can you use the DR-07 to change the
tempo of track playback, you can even do this
without changing the pitch. You can also change
Setting the playback control
functions
the playback pitch of a track without changing
the tempo.
Use the Playback Control Screen to set the play-
back control functions. When the Home Screen
is displayed, press and hold the PB CONT key to
open the Playback Control Screen.
You can use these playback control functions
effectively to practice and learn parts.
After you finish making settings on this screen,
press the STOP/HOME key (or press and hold the
PB CONT key) to return to the Home Screen.
In the upper part of the Home Screen, the icons for
the playback control functions that are currently
active appear highlighted in inverse.
TASCAM DR-07 71
Download from Www.Somanuals.com. All Manuals Search And Download.
11–Special Playback Control Functions
Control Screen from anything other than the
factory default results in the function being
turned ON all the time.
Changing the speed
Use the SPEEDitem to set the speed of playback.
However, setting the speed does not automatically
make the speed control function active. After
Change speed without changing
setting it, briefly press the PB CONT key to turn
pitch
the speed control ON, making it active. When ON,
the
icon appears as light letters on a dark
Turn the Variable Speed Audition (VSA) function
ON to keep the pitch the same when changing the
tempo. Use the VSAitem to turn the VSA function
ON and OFF (the factory setting is ON).
background in the upper part of the Home Screen.
You can turn the speed control ON and OFF by
briefly pressing the PB CONT key, so you can
easily switch between the set speed and the normal
speed.
Since the speed adjustment range is –50% to +16%
(in 1% increments), the slowest speed setting is
half the original speed.
NOTE
Briefly pressing the PB CONT key to turn the
speed setting function ON and OFF is unique
to this function. For all other playback control
functions, changing the setting on the Playback
72 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
11–Special Playback Control Functions
Changing the pitch without
changing the speed
Use the KEYitem to change the pitch in semitones
without changing the tempo.
Use the KEYitem to adjust the pitch up or down
by 1–6 semitones (Ã6–â6) (the factory setting is 0).
If you change the key to any value besides 0, the
key change function turns ON and the
icon
appears on the Home Screen as light letters on a
dark background.
Use the FINE TUNEitem to adjust the pitch up
or down in cents (100 cents = 1 semitone).
NOTE
Even if you use the FINE TUNEitem to adjust
the key, as long as the KEYitem setting is 0
the icon will not appear as light letters on a
dark background on the Home Screen.
,
TASCAM DR-07 73
Download from Www.Somanuals.com. All Manuals Search And Download.
12–Loop, Repeat and Single Playback
In ordinary playback mode, once playback starts,
it will stop when the end of the last track in the
current playback area is reached (or you press the
STOP/HOME key). By following the instructions
in this chapter, however, you can also make the
DR-07 loop a section of a track that you choose,
repeat the entire sequence of tracks in the current
playback area, play a single track repeatedly or
play a single track once and stop.
playback begins between the IN and OUT
points.
The current positions of the IN and OUT points are
shown by the and icons that appear below the
playback position display bar in the lower part of
the Home Screen. During loop playback the
indicator also appears.
To stop loop playback, press the I/O LOOP key.
The loop playback area setting is also cleared at the
same time.
Loop playback
NOTE
Accurate assignment of IN and OUT points is
not always possible for variable bit rate (VBR)
MP3 files.
With this function, you can continuously repeat
(loop) the playback of a selection that you make.
1 Press the I/O LOOP key during playback to
set the point when you want to start loop
playback. The current position is set as
the IN point.
2 Press the I/O LOOP key at the point when
you want loop playback to stop. The current
position is set as the OUT point, and loop
74 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
12–Loop, Repeat and Single Playback
• OFF:
Repeat and single track
All tracks in the playback area are played in
sequence one time. (This setting is the ordinary
playback mode.)
playback modes
You can set the DR-07 to repeatedly play the
current track or all tracks in the playback area, as
well as play just a single track once.
• SINGLE:
The selected track is played once without
repeating. The
Home Screen.
1 Press the MENU key to open the Menu
Screen. Select PLAY MODEand press
the ¥/π key. The Play Mode screen
icon appears on the
appears.
• 1 REPEAT:
The current track is played repeatedly. The
icon appears on the Home Screen.
• ALL REPEAT:
All tracks in the selected playback area are played
back repeatedly.
The
icon appears on the Home Screen.
NOTE
If you start loop playback, the REPEATitem
automatically switches to OFFif it is in a
different mode.
2 Select the REPEAT item to set the playback
mode to one of the following options.
TASCAM DR-07 75
Download from Www.Somanuals.com. All Manuals Search And Download.
13–System Settings and Formatting
From the Setup Screen, you can change various
settings to optimize the device for your use envi-
Making System Settings
ronment and other requirements. You can
also initialize and format the SD card.
Setting the search speed
Use the CUE/REV SPEEDitem to set the speed
of forward and backward searching when pressing
To open the Setup Screen, press the MENU key.
Select SETUPfrom the Menu Screen and press
and holding the ≤ and µ keys.
the ¥/π key.
Options: x2, x4, x8(factory setting), x10
The following settings can be made for the items
on the Setup Screen.
Turning the unit power OFF automatically
Use the AUTO OFFitem to set the time before
the unit power automatically turns OFF after
the last activity or use when powered by the
internal batteries.
Options: OFF(factory setting—the unit does not
automatically turn OFF), 3 min, 5 min, 10
min, 30 min
Backlight Auto OFF setting
Use BACKLIGHTto set the time until the
backlight automatically turns OFF after the last
operation when powered by the internal batteries.
76 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
13–System Settings and Formatting
Options: OFF(backlight always on), 5 sec
to highlight “Exec.”
(factory setting), 10 sec, 15 sec, 30 sec
2 Press the ¥/π key again to open a
confirmation pop-up window.
Adjust the display contrast
Use CONTRASTto adjust the display contrast.
Options: 1–20 (factory setting: 10)
3 Press the ¥/π key to initialize the unit.
Press STOP/HOME to cancel initialization.
Select the type of batteries
Use BATTERY TYPEto select the type of
batteries. This setting is used to distinguish the
remaining minimum power required for the normal
operation or to display the batteries’ remaining
power.
Formatting the SD card
Using QUICK FORMATor FULL FORMAT
erases all music files on the card and automatically
creates new “MUSIC” and “UTILITY” folders as
well as the “dr-1.sys” file that is necessary to use
the SD card with the DR-07.
Options: ALKAL(alkaline battery (factory
setting)), Ni-MH(nickel-metal hydride)
CAUTION
When the unit is shipped new from the factory,
its SD card also has a “MANUAL” folder that
contains a PDF copy of this Owner’s Manual file.
These are erased and not restored when the
card is formatted.
Restoring the factory settings
Use the INITIALIZEitem to restore the various
settings of this unit to their factory settings.
1 Select INITIALIZEand press the ¥/π key
TASCAM DR-07 77
Download from Www.Somanuals.com. All Manuals Search And Download.
13–System Settings and Formatting
NOTE
Using QUICK FORMAT
Full formatting of a 2GB SD card takes about 20
minutes or more depending on the type of SD
card.
Use the QUICK FORMATitem to quickly format
the SD card.
1 Select the FULL FORMATitem and press
1 Select the QUICK FORMATitem and press
the ¥/π key to highlight “Exec.”
the ¥/π key to highlight “Exec.”
2 Press ¥/π to open a pop-up confirmation
2 Press ¥/π to open a pop-up confirmation
window.
window.
3 Press the ¥/π key to execute the full
formatting, or press the STOP/HOME key
to cancel formatting.
3 Press the ¥/π key to execute the quick
formatting, or press the STOP/HOME key
to cancel formatting.
CAUTION
• When using FULL FORMAT, use the AC
adapter (sold separately) or confirm that
the batteries’ power remains enough.
If the power fails during formatting, the
formatting may not occur correctly.
Using FULL FORMAT
Use the FULL FORMATitem to completely
format the SD card.
• Depending on the size of the SD
card, FULL FORMAT could take an
hour or more. Please be patient and
do not disconnect the power during
formatting.
Full formatting checks the memory for errors
while formatting, so it takes more time than quick
formatting and you might have to wait a while.
78 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
14–Viewing File Information
Use the Information Screen to view various types
of information about your DR-07.
File information page
The FILEpage shows information about the
currently selected file.
To open the Information Screen, first press the
MENU key to open the Menu Screen. Select
“INFORMATION” and press the ¥/π key.
Use the wheel to switch between the following
three information pages.
File information page (FILE)
Shows information about the currently playing file.
Card information page (CARD
)
Shows the use status of the currently inserted
SD card
WAV or MP3
Shows the audio file type.
System information page (SYSTEM)
For WAV files, bit length, stereo/mono, and
sampling frequency (Hz) also appear.
Shows the unit’s system setting information and
firmware version
For MP3 files, the bit rate (kbps), CBR (constant
bit rate) or VBR (variable bit rate) type, and
sampling frequency (Hz) also appear.
TASCAM DR-07 79
Download from Www.Somanuals.com. All Manuals Search And Download.
14–Viewing File Information
TITLE
Card information page
Shows the file name. If an MP3 file has ID3 tag
title information, that information appears.
The CARDpage shows the status of the currently
inserted SD card.
DATE
The date of the file appears..
SIZE
The size of the file appears.
TOTAL MUSIC
Shows the number of playable files contained by
the Music Folder.
TOTAL FOLDER
Shows the total number of folders in the Music Folder.
TOTAL SIZE
Shows the total SD card memory capacity.
REMAIN SIZE
Shows the amount of unused memory on the SD card.
80 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
14–Viewing File Information
System information page
The SYSTEMpage shows information about the
DR-07’s system settings and firmware version.
CUE/REV SPD
Shows the speed of forward and backward searching.
AUTO OFF
Shows the automatic power OFF setting.
BACKLIGHT
Shows the automatic backlight OFF setting.
System Ver.
Shows the system firmware version.
TASCAM DR-07 81
Download from Www.Somanuals.com. All Manuals Search And Download.
15–LCD Menu List
Setting/
Operation Item
Menu Item
Page
Descriptions
File information display
FILE (1/3)
CARD (2/3)
SYSTEM (3/3)
SD card information display
System information display
File operation in SD card
Edit the playlist
INFORMATION
BROWSE
PLAYLIST
AREA
Set the repeat area
PLAY MODE
REPEAT
Set repeat mode
82 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
15–LCD Menu List
Setting/
Operation Item
Menu Item
Page
Descriptions
INPUT
GAIN
TYPE
Set the input source (MIC/LINE)
Set the GAIN of the MIC input
Set the stereo/mono of the MIC input
Set the On/Off of the phantom power to the MIC
input
INPUT SETTING
POWER
MIC
Set the Low Cut Filter (OFF/40 Hz/80 Hz/120
Hz)
Set the control function of the MIC input level
(OFF/AUTO/Limiter)
LOW CUT
LEVEL CTRL
FORMAT
SAMPLE
SIZE
Set the format of music files
Set the sampling frequency
Set the maximum file size
Set the On/Off of the pre-recording
Set the On/Off of the recording delay
Divide files
REC SETTING
DIVIDE
PRE REC
DELAY
TASCAM DR-07 83
Download from Www.Somanuals.com. All Manuals Search And Download.
15–LCD Menu List
Setting/
Operation Item
Menu Item
Page
Descriptions
CUE/REV SPEED
Set the fast forward/rewind speed (x2/x4/x8/x10)
Set the auto shut down time when operated by
batteries (Off/3 min/5 min/10 min/30 min)
Set the auto backlight turn off time (Off/5 sec/10
sec/15 sec/30 sec)
AUTO OFF
BACKLIGHT
CONTRAST
Set the LCD contrast
Set the battery type
SETUP
BATTERY TYPE
INITIALIZE
Execute the initialization
Execute the quick format
Execute the full format
Set the date and time
QUICK FORMAT
FULL FORMAT
DATE/TIME
84 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
16–Messages
Refer to this list if one of these popup messages
appears and you want to check the meaning or
determine a proper response.
The following is a list of the popup messages
that might appear on the DR-07 under certain
conditions.
Message
Meaning and response
File Name
The length of the file name is longer than 200 characters when the Divide is
used.
ERR
Dup File
Name
The same file name already exists when a new file is created when the Divide is
used.
File not
found
The audio file cannot be found or is corrupted. Check the file (using a
computer).
Non-
The audio file is not a supported format. Check the file format (using a
computer).
Supported
Battery
Empty
The batteries are almost out of power. Replace the batteries or use an AC
adapter (sold separately).
I/O Too
Short
When using the I/O LOOP key, the IN and OUT points are too close together
to start loop playback. Set the interval to at least one second. Reset the IN and
OUT points and try again.
TASCAM DR-07 85
Download from Www.Somanuals.com. All Manuals Search And Download.
16–Messages
Message
Meaning and response
File Not
The file in the Playlist cannot be found. Please confirm that the file is still in the
Music Folder.
Found
PLAYLIST
No PLAYLIST
No files are in the Playlist. This appears when the PLAY MODEis set to
PLAYLIST, but no files have been added to the Playlist. Add a file to the
Playlist. See “Adding tracks to the playlist” on page 63.
PLAYLIST
FULL
You cannot add more than 99 tracks to the Playlist. Erase an unneeded file from
the Playlist and then add the new file. See “Editing the playlist” on page 64.
MBR Error
Init CARD
There is a problem with the Master Boot Record. The card is not formatted
properly or the formatting is broken. When “Are you Sure?” appears,
press the ¥/π key to format the entire card in FAT format.
CAUTION
Execution of FAT formatting erases all data currently on the card.
86 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
16–Messages
Message
Meaning and response
Format
Error
The FAT formatting of the card is abnormal or broken. This message also
appears if you FAT formatted the card using a computer connected by USB (or
by card reader). This message also appears when a new card is inserted in the
unit. Always use the DR-07 to conduct FAT formatting of cards to be used with
it.
Format CARD
When “Are you Sure?” appears, press ¥/π to FAT format the entire
card.
CAUTION
Execution of FAT formatting erases all data currently on the card.
File Not
Found
The system file is missing. This unit requires a system file for operation. When
“Are you Sure?” appears, press ¥/π to automatically create a system
file.
Make Sys
File
Invalid
SysFile
Make Sys
File
The system file is invalid. The system file required to operate this unit has
become abnormal or broken. When “Are you Sure?” appears, press the
¥/π key to automatically create a valid system file.
Invalid
Card
This appears when there is some type of error with the card.
Change Card
TASCAM DR-07 87
Download from Www.Somanuals.com. All Manuals Search And Download.
16–Messages
Message
Meaning and response
Protected
This appears when the card in the unit during startup is a protected card without
the necessary Music Folder and other folders and files.
Card
Change Card
Write
Writing to the card timed out.
Timeout
Backup files on the card to your computer, and format the card using the DR-07.
Erase unnecessary files or move them to your computer to make open space.
Card Full
Layer too
Deep
A folder cannot be created below this level.
Can't
The position set for division is not suitable (song beginning or end).
Divide
Max File
Size
The file is larger than the designated size or the recording time exceeds 24
hours.
File Full
The total number of folders and files is already 999. Erase unnecessary files or
move them to your computer.
Card Error
There was some sort of error with the card. Turn off the power and replace the
card with a working card.
88 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
16–Messages
Message
Meaning and response
Not
Continued
File Error
Can't Save
Data
Player Error
Device Error
Writing Failed
Sys Rom Err
If any of these errors occur, turn the DR-07 power OFF and restart the unit.
If the error message continues to appear, contact a TEAC Repair Center.
System Err 50
System Error
1
TASCAM DR-07 89
Download from Www.Somanuals.com. All Manuals Search And Download.
16–Messages
Message
Meaning and response
System Error
2
System Error
3
System Error
4
System Error
If any of these errors occur, turn the DR-07 power OFF and restart the unit.
If the error message continues to appear, contact a TEAC Repair Center.
5
System Error
6
System Error
7
System Error
8
System Error
9
90 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
17–Specifications
Audio Input and Output
MIC IN input
Jack
3.5-mm stereo phone (with plug-in power)
30 kΩ
Input impedance
Nominal input level
-64 dBV (GAIN set to HIGH)
-48 dBV (GAIN set to MID)
-32 dBV (GAIN set to LOW)
-48 dBV (GAIN set to HIGH)
-32 dBV (GAIN set to MID)
-16 dBV (GAIN set to LOW)
Maximum input level
LINE IN input
Jack
Input impedance
Nominal input level
3.5-mm phone (stereo)
23 kΩ
-10 dBV
Maximum input level
+6 dBV
/LINE OUT output
Jack
3.5-mm phone (stereo)
-14 dBV
Nominal line output
Maximum line output
+2 dBV
Maximum headphones output
15 mW + 15 mW (with 32 Ω impedance headphones)
TASCAM DR-07 91
Download from Www.Somanuals.com. All Manuals Search And Download.
17–Specifications
Audio performance
20 Hz–20 kHz, +1/-3 dB
0.015% or less (at 1 kHz, +6 dBV input)
87 dB or more
Frequency response (LINE IN > /LINE OUT)
Distortion (LINE IN > /LINE OUT)
S/N ratio (LINE IN > /LINE OUT)
Other specifications
Audio file compatibility
MP3 files
32–320 kbps
44.1/48 kHz sampling frequency
VBR (playback only)
ID3 tag support up to Ver 2.4
44.1/48 kHz sampling frequency
16/24-bit rate
WAV files
Recording medium
SD card (64 MB–2 GB) or SD HC card (4–32 GB)
FAT16/32
File system
Physical
Battery life (continuous operation)
About 7.5 hours when recording
About 8.5 hours when playing
(using alkaline batteries, no back light, MP3 128 kbps,
varies with operating conditions)
5 to 35°C
Operating temperature
Power consumption
0.7 W (during MP3 playback)
92 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
17–Specifications
Dimensions
(not including protrusions)
Weight
55 (W) x137 (H) x 27 (D) (mm)
2.2 (W) x 5.4 (H) x 1.1 (D) (inches)
130 g (without batteries)
Computer requirements
Windows
Macintosh
Pentium 300 MHz or faster
128 MB or more memory
USB port (USB 2.0 recommended)
Power PC, iMac, G3, G4 266 MHz or faster
64 MB or more memory
USB port (USB 2.0 recommended)
Recomended USB host controller
Supported OS
Intel chipset
Windows 2000 SP4 or later, Windows XP and Windows
Vista
Mac OS X 10.2 or later
Accessories available for purchase
AC adapter (PS-P520)
TASCAM DR-07 93
Download from Www.Somanuals.com. All Manuals Search And Download.
17–Specifications
Dimensions
Specifications and external appearance may be changed without notification to improve the product.
Illustrations and other depictions in the owner’s manual may differ in part from the actual product as a result of
product improvements.
•
•
94 TASCAM DR-07
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
DR-07
TEAC CORPORATION
Phone: +81-42-356-9143
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
7733 Telegraph Road, Montebello, California 90640, U.S.A.
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. de C.V.
Phone: +52-55-5010-6000
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México
TEAC UK LIMITED
Phone: +44-8451-302511
Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|