D01128520B
LR-10
Instrumental
Trainer/Recorder
This device has a serial number
located on the bottom panel. Please
record it and retain it for your
records.
Serial number:
__________________
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1
2
3
4
5
6
7
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•
•
•
Do not expose this apparatus to drips or splashes.
Do not place any objects filled with liquids, such as vases, on the apparatus.
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Do not install this apparatus in a confined space such as a book case or
similar unit.
8
9
Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
10 Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the manufacturer.
1 2 Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
•
•
•
•
•
The apparatus draws nominal non-operating power from the AC outlet with
its POWER or STANDBY/ON switch not in the ON position.
The apparatus should be located close enough to the AC outlet so that you
can easily grasp the power cord plug at any time.
The mains plug is used as the disconnect device, the disconnect device shall
remain readily operable.
If the product uses batteries (including a battery pack or installed batteries),
they should not be exposed to sunshine, fire or excessive heat.
CAUTION for products that use replaceable lithium batteries: there is danger
of explosion if a battery is replaced with an incorrect type of battery. Replace
only with the same or equivalent type.
•
Caution should be taken when using earphones or headphones with the
product because excessive sound pressure (volume) from earphones or
headphones can cause hearing loss.
13 Unplug this apparatus during lightning storms or when unused for long
periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord
TASCAM LR-10 3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
•
Remove the batteries if you do not plan to use the unit for a long time.
ª Cautions about Batteries
This product uses batteries. Misuse of batteries could cause a leak, rupture or
other trouble. Always abide by the following precautions when using batteries.
Batteries could rupture or leak, causing fire, injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the battery compartment
before inserting new batteries.
•
Never recharge non-rechargeable batteries. The batteries could rupture or
leak, causing fire or injury.
ª For European Customers
•
When installing batteries, pay attention to the polarity indications
(plus/minus (+/–) orientation), and install them correctly in the battery
compartment as indicated. Putting them in backward could make the
batteries rupture or leak, causing fire, injury or stains around them.
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
•
•
When throwing used batteries away, follow the disposal instructions
indicated on the batteries and the local disposal laws. When you store or
dispose of batteries, isolate their terminals with insulation tape or something
like that to prevent them from contacting other batteries or metallic objects.
(b) By disposing of the electrical and electronic equipment correctly, you will
help save valuable resources and prevent any potential negative effects on
human health and the environment.
(c) Improper disposal of waste equipment can have serious effects on the
environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment.
Do not use batteries other than those specified. Do not mix and use new
and old batteries or different types of batteries together. The batteries could
rupture or leak, causing fire, injury or stains around them.
(d) The crossed out wheeled dust bin symbol indicates that electrical and
electronic equipment must be collected and disposed of separately from
household waste.
•
•
•
Do not carry or store batteries together with small metal objects. The
batteries could short, causing leak, rupture or other trouble.
Do not heat or disassemble batteries. Do not put them in fire or water.
Batteries could rupture or leak, causing fire, injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the battery case before
inserting new batteries. If the battery fluid gets in an eye, it could cause loss
of eyesight. If fluid does enter an eye, wash it out thoroughly with clean
water without rubbing the eye and then consult a doctor immediately. If the
fluid gets on a person’s body or clothing, it could cause skin injuries or burns.
If this should happen, wash it off with clean water and then consult a doctor
immediately.
(e) The return and collection systems are available to the end users. For
more detailed information about disposal of old electrical and electronic
•
The unit power should be off when you install and replace batteries.
4 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
equipment, please contact your city office, waste disposal service or the
shop where you purchased the equipment.
Disposal of batteries and/or accumulators
(a) Waste batteries and/or accumulators should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
Pb, Hg, Cd
(b) By disposing of waste batteries and/or accumulators correctly, you will
help save valuable resources and prevent any potential negative effects on
human health and the environment.
If the battery or accumulator contains more than the specified values
of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery
Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury
(Hg) and/or cadmium (Cd) will be indicated beneath the crossed out
wheeled dust bin symbol.
(c) Improper disposal of waste batteries and/or accumulators can have serious
effects on the environment and human health as a result of the presence of
hazardous substances in batteries and/or accumulators.
(e) The return and collection systems are available to the end users. For more
detailed information about disposal of waste batteries and/or accumulators,
please contact your city office, waste disposal service or the shop where you
purchased them.
(d) The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from household
waste.
TASCAM LR-10 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS .........................2 2–Names and Functions of Parts..............................24
Top panel........................................................................................... 24
Left side panel.................................................................................. 30
6 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
File operations ................................................................................. 58
5–Recording...............................................................48 7–Playback .................................................................61
signals................................................................................................. 63
TASCAM LR-10 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
8 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Input ratings..................................................................................... 97
TASCAM LR-10 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
ª Preparing the power
Step 1: Prepare the SD card and
power
Using AA batteries
Insert AA batteries into the battery compartment, which you
opened when installing the SD card. This unit can use either
alkaline or nickel-metal hydride (Ni-MH) batteries. It cannot
recharge batteries.
ª Install the SD card
Insert the SD card into the SD card slot, which is inside the
battery compartment on the bottom of the unit.
Formatting is necessary if you insert a new SD card.
(Formatting will erase all the data on the card.)
For details, see “Inserting and removing SD cards”on page 39.
10 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
Using USB bus power
Using an AC adaptor (sold separately)
Connect the unit with a computer using the included USB
cable.
Connect a TASCAM PS-P520 AC adaptor (sold separately),
which is designed for the specifications of this unit, to the DC
IN 5V jack.
Computer
USB
AC outlet
TACAM
PS-P520
(sold separately)
The USB SELECTscreen appears, allowing you to set whether
DC plug
to use USB bus power or to connect the unit’s storage to the
computer. Select BUS POWER
.
ª Turn the power on
Press and hold the
opens.
[ª] button until the startup screen
For details about power preparations, see “Powering the unit”
on page 42.
TASCAM LR-10 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
Be sure to use file formats that this unit can play back. These
formats include MP3 (32–320 kbps, 44.1 kHz) and WAV (44.1
kHz, 16/24-bit).
ª Setting the date and time
Use the DATE/TIMEitem from the MENUto set the internal
clock to the current time.
ª Connect the computer
Use the included USB cable to connect the unit to the
computer.
ª Transfer files from the computer
Copy audio files to the MUSIC folder on the LR-10 drive that
appears on the computer.
The unit uses its internal clock to include the date and time of
the recording in its file.
ª Disconnect from the computer
The unit will function properly even if you do not make this
setting. When you first put batteries into the unit, however,
the clock will begin advancing from the default value of
2000-01-01/00:00:00 and this incorrect date and time will be
added to recording files. (See “Setting the date and time”on
page 45.)
After using the correct procedures to dismount the LR-10
drive from your computer, disconnect the USB cable. The unit
should automatically turn off.
For details, see Chapter 11 “Transferring songs to and from a
computer”on page 76.
Step 2: Copy audio files from a
computer
Step 3: Select the input
Set INPUTto MICto use the built-in microphone to practice
singing or playing a wind instrument, for example.
ª Prepare the audio files
Create audio files using the functions of the computer
operating system or other computer software applications.
Set INPUTto LINEto use the LINE IN jack to practice playing
a synthesizer or electronic piano.
12 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
ª Connect headphones or speakers
Connect headphones or a monitoring system (such as
powered speakers or an amplifier and speakers) to this unit’s
/LINE OUT jack.
For details, see “Connecting monitoring equipment”on page
46.
For details, see “Setting the input functions”on page 48.
CAUTION
Step 4: Connect an instrument and
headphones
Before connecting headphones, use the OUTPUT (–) button
to minimize the volume. Failure to do so could cause the
sudden output of loud sounds, which might lead to hearing
damage or other harm.
ª Connect an instrument
Connect the headphones/stereo line output jack of the
keyboard or other instrument to the LINE IN jack of this unit
using a 3.5-mm miniplug cable.
Step 5: Tune the instrument
For details, see “Connecting an instrument”on page 47.
Use the unit’s tuning function to tune an instrument using the
LINE IN jack or built-in microphones.
CAUTION
Press the TUNER button to open the TUNERscreen.
To record the sound from the LINE IN jack or hear it through
headphones, line input must be ON (
activated, set the INPUTitem in the INPUT SETTINGmenu
to LINE. If the line input is OFF ( ), press the ¶/MIC
button to turn it ON ( ).
). If mic input is
For details, see Chapter 13 “Using the tuner”on page 80.
TASCAM LR-10 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
Step 6: Use the effects
Step 7: Adjust the input and output
levels
This unit has built-in effects. You can use these effects on the
input signal and on the playback signal.
ª Adjust the headphones volume
Use the OUTPUT (+/–) buttons to adjust the headphones
volume.
Press the EFFECT button briefly to enable the effects. The
last effect setting used is activated and the FXicon appears
highlighted (light letters on a dark background).
When adjusting the volume, the current level appears in a
pop-up at the bottom of the display.
Press this button again to disable the effects. The FXicon
appears as dark letters on a light background.
For details, see “Adjusting the playback volume”on page 62.
Press and hold the EFFECT button to open the EFFECTscreen
where you can make detailed settings.
ª Adjusting the microphone and line input level
Use the INPUT level dial on the right side panel to adjust the
built-in microphones and LINE IN input level.
For details, see Chapter 12 “Using the built in effects”on page
78.
14 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
For details, see “Adjusting the input level”on page 49.
Step 8: Play along with the music
ª Adjusting the mix
This unit will output the sound input through the mic or the
LINE IN jack even when recording is not enabled. This allows
you to select a song and play along after pressing the Á
button.
Press the BALANCE button to adjust the volume of the
file that is playing. Use this function to adjust the balance
between the playback sound and the sound of the input from
the built-in microphones or the LINE IN jack. Press the Á
button to start playback of the song. Adjust the volume of the
playback sound using the VALUE (+/–) buttons. While playing
the instrument, adjust the balance between the playing song
and the instruments.
This unit also has the following functions, which you can use
as you like to make practicing your instrument even easier.
ª Use repeat playback
You can use two types of repeat playback. You can either play
a loop between two set points or play an entire song and the
entire playback area repeatedly.
Use the LOOP button for loop playback, which is useful for
practicing a phrase repeatedly.
NOTE
During playback (or when paused), press the LOOP button
briefly at the point where you want to start loop playback to
set the IN point. Then, press the LOOP button briefly again
at the point where you want to stop loop playback to set the
OUT point and start loop playback of the interval between the
points.
The BALANCEsetting only affects the volume when MIC or
LINE is ON (
), changing the BALANCEvalue has no effect on the
volume.
or
). When MIC or LINE is OFF (
or
TASCAM LR-10 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
For details about repeat playback, see “Repeat and single track
playback”on page 75.
ª Change the key
You can change the playback pitch (key) in semitones. Press
the KEY button to show the key setting at the bottom of the
display.
Press and hold the LOOP button to open the LOOP SET
pop-up screen where you can make fine adjustments to the
IN and OUT points. Other loop playback functions include, for
example, the possibility of setting up to five loops for each file
when the playback area is the playlist.
For details about loop playback see “Using loop playback
(standard mode)”on page 72 and “Using loop playback with
the playlist”on page 73.
Use the VALUE (+/–) buttons to change the setting value.
For details, see “Changing the key”on page 70.
For repeat playback of a single file or the entire playback area,
press the MENU button to open the MENUscreen, select PLAY
MODEand press the Áor ¯button. Use the VALUE (+/–)
ª Changing the speed
You can also change the playback speed without changing
the pitch.
buttons to select 1REPEATor ALLREPEAT
.
You can, for example, reduce the speed to practice a song and
gradually increase it as you become more proficient.
Press the SPEED button to show the speed setting at the
bottom of the display.
After making the setting, press the HOME button to return to
the Home Screen.
16 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
Step 10: Record over a song
(overdub)
You can also record your performance together with the
music that is playing back.
Use the VALUE (+/–) buttons to change the setting value.
Use the Âand ¯buttons to select the song. Press
the Ábutton while pressing and holding the RECORD [–]
button to begin overdubbing.
For details, see “Changing the speed”on page 70.
Press the
[ª] button to stop recording.
Step 9: Record your performance
For details, see “Recording the input sound with the playback
sound (overdubbing)”on page 51.
You can record the sound input through the built-in
microphones or the LINE IN jack. Press the RECORD [–]
button to start recording (except when the auto-record
function is on and the input level is below the set value). Press
and hold the RECORD [–] button to enable the pre-record
function and put the unit into recording standby. Press the
RECORD [–] button to start recording, capturing sound up
CAUTION
If you press and hold the record button, the unit will be put in
recording standby with the pre-record function enabled, and
overdubbing will not be possible.
to 2 seconds before pressing the button. Press the
button to stop recording.
[ª]
For details, see “Recording”on page 50.
TASCAM LR-10 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide
Step 11: Use other functions
This unit has other functions, including a convenient playlist
and the ability to divide files, which you can use as you like.
One such function is the metronome, which can be accessed
easily by pressing the METRONOME button.
For details, see chapter 14 “Using the Metronome”on page 82.
Step 12: Turn off the power
To turn the power off (put the unit in standby), press the
[ª] button and hold it until the shutdown screen appears.
18 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
Thank you very much for purchasing the TASCAM LR-10
Instrumental Trainer/Recorder. Please read this Owner’s
Manual carefully in order to maximize your use of all the
unit’s features. We hope that you will enjoy using this trainer/
recorder for many years to come. Please keep a copy of this
manual in a safe place for future reference.
Built-in effects can be applied to the input signal and the
playback signal
•
Tuner functions
•
•
Auto recording function can detect the sound input level
to start recording automatically
Recording continues automatically in a new file without
pause when the maximum file size is reached during
recording
•
You can also download a digital version of this manual from
the TASCAM website (http://www.tascam.com/).
Track incrementation function allows the creation of a new
file when desired during recording without pause
•
•
•
•
•
•
Main functions and features
Pre-recording (PRE REC) function allows the unit to record
the 2 seconds of sound before recording is activated
Portable trainer/recorder for acoustic instruments players
Uses SD cards as recording media
•
•
•
Auto gain control function automatically make the micro-
phone input level as even as possible
Record using the built-in microphones or a connected
external device
Limiter function automatically reduces the level suitably
when the microphone input level is too high
Recording 44.1 kHz, 16-bit linear PCM (WAV format)
possible
•
•
•
•
Low cut filter for microphone input conveniently reduces
low-frequency noise
Overdubbing the input signal with the audio playing back
possible
VSA function allows adjustment of the playback speed in
a range from 50% to 150% (in 10% increments) without
changing the playback pitch
Playback of 44.1 kHz, 16/24-bit linear WAV files and 44.1
kHz, 32–320 kbps MP3 files possible
Key adjustment function allows the pitch to be adjusted by
6 semitones (in semitone increments)
Metronome functions
•
TASCAM LR-10 19
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
Rec delay function can be used to avoid recording the
sound of pushing the RECORD [º] button
Take care when opening the package not to damage the
items. Keep the package materials for transportation in the
future.
•
Repeat playback and IN-OUT loop playback functions
Playlist function
•
•
•
Please contact the store where you purchased this unit if any
of these items are missing or have been damaged during
transportation.
In playlist mode, up to five IN-OUT loop playback settings
can be made for each file
Main unit ...............................................................................................1
SD memory card (in the unit) .........................................................1
AA alkaline battery .............................................................................2
USB cable (0.8 m) ................................................................................1
A warranty card....................................................................................1
Owner’s manual (this manual)........................................................1
•
Divide function allows files to be split where desired
•
•
•
•
File name format can be set to use a user-defined word or
the date
•
1/8”external stereo line input jack
1/8”line output/headphones output jack
128 × 64 pixel dot matrix LCD
Mini-B type USB 2.0 port
•
•
•
•
•
•
•
Can be powered by two AA batteries, USB bus power or a
TASCAM PS-P520 AC adaptor (sold separately)
About this manual
In this manual, we use the following conventions:
Files saved on a computer can be transferred (copied) to
the SD card in this unit via USB
•
“SD memory card”is sometimes abbreviated as “SD card.”
•
•
The names of keys and controls are given in the following
bold typeface: MENU
Included items
Messages shown on the unit’s display are written like this:
ON
•
The included items are listed below.
20 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
Characters that appear on a computer display are given in
the following light typeface: OK
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
•
•
•
•
Additional information is introduced in the styles below
when needed:
Microsoft, Windows, Windows XP, Windows Vista, and
Windows 7 are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other
countries.
TIP
Useful hints when using the unit.
Apple, Macintosh, iMac, Mac OS and Mac OS X are trade-
marks of Apple Inc.
•
•
NOTE
Explanation of actions in special situation and supplement.
Other company names, product names and logos in this
document are the trademarks or registered trademarks of
their respective owners.
CAUTION
Instructions that should be followed to avoid injury, damage
to the unit or other equipment, and loss of data.
Any data, including, but not limited to information,
described herein are intended only as illustrations of such
data and/or information and not as the specifications for
such data and/or information. TEAC Corporation disclaims
any warranty that any use of such data and/or information
shall be free from infringement of any third party’s
intellectual property rights or other proprietary rights,
and further, assumes no liability of whatsoever nature
in the event of any such infringement, or arising from or
connected with or related to the use of such data and/or
information.
Intellectual property rights
TASCAM is a trademark of TEAC Corporation, registered in
the U.S. and other countries.
•
•
SDHC Logo is a trademark of SD-3C, LLC.
TASCAM LR-10 21
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
About SD cards
This product is designed to help you record and
reproduce sound works to which you own the copyright,
or where you have obtained permission from the
copyright holder or the rightful licensor. Unless you
own the copyright, or have obtained the appropriate
permission from the copyright holder or the rightful
licensor, your unauthorized recording, reproduction or
distribution thereof may result in severe criminal penalties
under copyright laws and international copyright treaties.
If you are uncertain about your rights, contact your legal
advisor. Under no circumstances will TEAC Corporation be
responsible for the consequences of any illegal copying
performed using the recorder.
This unit uses SD cards for recording and playback.
You can use 64 MB–2 GB SD cards and 4 GB–32 GB SDHC cards
with this unit.
A list of SD cards that have been tested with this unit can be
found on the TASCAM web site (www.tascam.com/).
Use of cards that have not been verified for use with this unit
could result in the unit not functioning properly.
Precautions for use
SD cards are delicate media. In order to avoid damaging a
card or the card slot, please take the following precautions
when handling them.
Do not leave in extremely hot or cold places.
Do not leave them in extremely humid places.
Do not let them get wet.
•
•
•
•
•
Do not put things on top of them or twist them.
Do not hit them.
22 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1–Introduction
Beware of condensation
Precautions for placement and use
The operating temperature should be between 0°C and
40°C (32°F and 104°F).
If the unit is moved from a cold to a warm place, or used
after a sudden temperature change, there is a danger of
condensation; vapor in the air could condense on the internal
mechanism, making correct operation impossible. To prevent
this, or if this occurs, let the unit sit for one or two hours at the
new room temperature before using.
•
•
Do not install in the following types of places. Doing
so could degrade the sound quality and/or cause
malfunctions.
Places with significant vibrations or that are otherwise
unstable
•
Cleaning the unit
Near windows or other places exposed to direct sunlight
Near heaters or other extremely hot places
Extremely cold places
•
•
•
•
•
Use a dry soft cloth to wipe the unit clean. Do not clean the
unit with a chemically treated cloth or substances such as
benzene, thinner and alcohol because they might cause
damage to the surface of the unit.
Places with bad ventilation or high humidity
Very dusty locations
Avoid installing this unit on top of any heat-generating
electrical device such as a power amplifier.
•
TASCAM LR-10 23
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
3 Cursor control
Top panel
Press up to use the §/BROWSE button, down to use the
¶/MIC button, left to use the Âbutton and right to
use the ¯button.
§/BROWSE button (UP/BROWSE)
When the Home Screen is open, press this button to
open the BROWSEscreen.
When one of the setting screens is open, this moves
the cursor up on the screen.
When the Home Screen is open, press and hold this
button to open the QUICK DELETEpop-up menu.
¶/MIC button (DOWN/MIC INPUT)
When the Home Screen is open, press this button to
turn input from the built-in microphone or LINE IN
jack ON/OFF.
When one of the setting screens is open, this moves
the cursor down on the screen.
1 Display
This shows a variety of information.
Âbutton (PREVIOUS)
2 PEAK indicator
During playback or when stopped, press this button to
return to skip to the beginning of the previous file.
This lights if the input signal level is too high.
When one of the setting screens is open, this moves
the cursor to the left on the screen.
On the BROWSEscreen, press this button to return to
the higher folder level.
24 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
¯button (NEXT)
5 button (F FWD)
During playback or when stopped, press this button to
skip to the beginning of the next file.
Press this button to search forward.
Press briefly to search forward to the end of the current
file. Each time you press this button, the search speed
increases.
When one of the setting screens is open, this moves
the cursor to the right on the screen.
On the BROWSEscreen, press this to enter the lower
folder level.
Press and hold to search forward continuously for as long
as the button is pressed. When the end of the current file
is reached, searching stops there.
Press during recording to start recording to a new file
without interruption (track incrementation).
6
[ª] button (POWER, STOP)
Use to stop recording and playback, as well as to end
recording standby.
4 Ôbutton (REW)
Press this button to search backward.
Press during playback to pause playback. Press again
when paused to stop playback.
Press briefly to search backward to the beginning of the
current file. Each time you press this button, the search
speed increases.
Use also to respond “NO”to a confirmation pop-up
message that appears during the operation of a setting
screen.
Press and hold to search backward continuously for as
long as the button is pressed. When the beginning of the
current file is reached, searching stops there.
Use to return from the FILE INFORMATIONpop-up
message when using the browse function.
Press and hold to turn the power ON or put the unit into
standby.
TASCAM LR-10 25
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
recording standby to start recording. When recording, the
indicator lights.
7 Ábutton (PLAY)
When the Home Screen is open, press when stopped to
start playback.
Press the Ábutton while pressing and holding this
button to start overdubbing. (See “Recording the input
sound with the playback sound (overdubbing)”on page
51.)
Press during playback to return to a specific time and
restart playback (flashback function). (See “Jump back a
set amount and continue playback (flashback)”on page
71.)
On the DIVIDEscreen, use to execute the division of a file.
When the METRONOMEscreen is open, press to start and
stop the metronome.
9 VALUE (+/–) buttons
Use these to change setting values. Press + to increase the
value or – to decrease the value.
Use during operation of a setting screen to confirm the
selection of an item and to respond “YES”to confirmation
pop-up messages.
Press + and - buttons at the same time to set it to the
default value.
Press this button while pressing and holding the RECORD
[º] button to start overdubbing. (See “Recording the
input sound with the playback sound (overdubbing)”on
page 51.)
0 OUTPUT (+/–) buttons
Use these to adjust the volume level of the output from
the built-in speaker or the /LINE OUT jack. When using
these buttons, the volume level is shown in a pop-up at
the bottom of the display.
8 RECORD [º] button/indicator
Press briefly when stopped to start recording. When
recording, the indicator lights. When the auto record
function is ON, press briefly to start recording standby.
When in recording standby, the indicator blinks.
Press + to increase the volume or – to decrease the
volume.
q HOME button
Press to return to the Home Screen from one of the setting
screens.
Press and hold when stopped to enable prerecording (2
seconds maximum) and start recording standby. When
in recording standby, the indicator blinks. Press during
26 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
w Trainer buttons
r KEY button
In addition to the MENU button, which opens the MENU
screen, this section has seven buttons that allow direct
access to various training functions. By using them, you
can change their settings without having to return to the
Home Screen each time.
Press to change the pitch of the playback. Press to cycle
between the two modes. Use the VALUE (+/–) buttons to
increase/decrease the pitch.
Adjust the pitch in semitones using the KEYmode.
Adjust the pitch in cents using the FINETUNEmode.
For details, see “Changing the key”on page 70.
e SPEED button
Press to change the playback speed.
t TUNER button
Press to tune the instrument.
Use the VALUE (+/–) buttons to increase/decrease the
playback speed. For details, see “Changing the speed”on
page 70.
TASCAM LR-10 27
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
First, set the tuner mode to AUTOor OSCusing the
[ª]button (AUTO) and Ábutton (OSC). Then, press the
TUNER button again and change the setting for the mode
using the VALUE (+/–) button or Á button.
The cursor starts on the last used item.
Press this button when one of the setting screens is open
to return to the MENUscreen.
Press this button when the MENUscreen is open to return
to the Home Screen.
For details, see Chapter 13 “Using the tuner”on page 80.
y EFFECT button
For details, see “Using the menu”on page 37.
Press briefly to turn the effects ON/OFF. When ON, the FX
icon appears with light letters on a dark background.
i BALANCE button
Press to change the volume level of the playback sound
and balance playback and input signals.
Press and hold to open the EFFECTscreen where you can
make detailed settings.
Use the VALUE (+/–) buttons to increase/decrease the
playback volume.
For details, see Chapter 12 “Using the built in effects”on
page 78.
For details, see “Adjusting the balance between playback
and input signals”on page 63.
u MENU button
When the Home Screen is open, press this button to open
the MENUscreen.
NOTE
The BALANCEsetting only affects the volume when MIC or
LINE is ON (
), changing the BALANCEvalue has no effect on the
volume.
or
). When MIC or LINE is OFF (
or
28 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
When the playback area is set to playlist, press this button
briefly to show the currently selected loop number.
o METRONOME button
Press to use the metronome.
If the loop range has been set, the “ ”and “ ”icons will
appear under the playback position bar.
Press this button to cycle through the TEMPO, BEATand
LEVELsettings in order.
Use the VALUE (+/–) buttons to change the selected loop
number (LOOP 1– LOOP 5).
Use the VALUE (+/–) buttons to change the value of each
setting.
When the playback area is set to playlist, press and hold
this button to show the loop screen.
For details, see Chapter 14 “Using the Metronome”on
page 82.
p LOOP button
When the playback area is not set to playlist, press this
button briefly to set the IN point (loop playback starting
point) at the current location. Press briefly again to set the
OUT point (loop playback ending point) and start loop
playback.
Press the Âbutton designate the IN point, and press
the ¯button to designate the OUT point. You can press
the Â/¯button again to change the IN/OUT point.
Use the Áand Ô/buttons to find the location in
the track where you want to set each point.
Press briefly again to turn the loop playback function OFF.
TASCAM LR-10 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
For details, see “Using loop playback (standard mode)”on
page 72 and “Using loop playback with the playlist”on
page 73.
Right side panel
Left side panel
d
/LINE OUT jack
Connect headphones here or connect a stereo mini-jack
cable from here to the line input jack of another audio
device.
f INPUT volume
a USB port
Use to adjust the input level of the built-in microphones
or LINE IN jack signal.
Use this port to connect the unit to a computer using the
included USB cable. (See “Connecting with a computer”on
page 46.)
g LINE IN jack
Use this stereo 3.5-mm (1/8”) mini jack to connect another
audio device.
s REMOTE jack
Connect a TASCAM RC-3F foot switch (sold separately),
which is designed for use with this unit, to this 2.5-mm
TRS jack.
30 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
Front panel
Rear panel
h DC IN 5V jack
j Built-in stereo microphone (L/R)
Connect a TASCAM PS-P520 AC adaptor (sold separately),
which is designed for the power requirements of this unit.
This is an electret condenser stereo microphone. To use
this microphone as the input source, set INPUTto MICon
the INPUT SETTINGscreen.
k Built-in mono speaker
Use this built-in speaker for monitoring.
This speaker is disabled when headphones are connected,
when recording and when in recording standby.
TASCAM LR-10 31
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
Install batteries (2 AA) in this compartment to power the
unit. (See “Using AA batteries”on page 42.)
Bottom panel
z SD card slot
Use to insert and remove SD cards. (See “Inserting and
removing SD cards”on page 39.)
l Battery compartment cover
; Battery compartment
32 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
: Loop playback
Home Screen
3 Key adjustment status
This shows whether key adjustment is ON or OFF.
: Key adjustment OFF
The following information appears on the display when the
Home Screen is open.
: Key adjustment ON
4 Effect ON/OFF status
This shows whether the effects are ON or OFF.
: Built-in effects OFF
: Built-in effects ON
5 MIC/LINE input ON/OFF status
These icons show whether the built-in mic and LINE IN
jack inputs are ON or OFF.
1 Playback speed status
: Built-in microphones OFF
: Built-in microphones ON
: Line input OFF
Depending on the playback speed setting, the icon
appears as follows.
Normal playback
speed
110–150% speed
50–90% speed
: Line input ON
6 Power supply status
When the unit is being operated on battery power, a
battery (
The amount of remaining battery charge is shown by the
number of bars in the icon ( ).
) icon is shown.
2 Loop playback/repeat playback setting status
Depending on the setting, the icon appears as follows.
,
,
: Single playback
: Repeat playback of one song
: Repeat playback of all songs
TASCAM LR-10 33
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
When almost no battery charge is remaining, the empty
9 Playback interval
battery (
) icon blinks. When this happens, the unit will
This shows the loop playback IN point (starting point) and
OUT point (ending point) settings.
soon switch to standby.
When using a TASCAM PS-P520 AC adaptor (sold
When a starting point is set, the “ ”icon appears at the
corresponding position beneath the playback position
bar.
separately) or USB bus power, the AC (
) icon is shown.
NOTE
When an ending point is set, the “ ”icon appears at the
corresponding position beneath the playback position
bar.
Even when some battery charge is remaining, a “Battery
Low”pop-up message might appear if you try to start
recording or another operation that requires a lot of power.
0 File information
7 Recorder operation status
This shows the name of the file being played back. If
an MP3 file has ID3 tag information, that information is
shown instead.
Depending on the recorder operation status, one of the
following icons appears.
ª
Stopped
Paused
NOTE
π
Á
Playing back
Searching forward
Searching backward
Skipping to the beginning of the next file
Skipping to the beginning of the previous file
ID3 tag information is title and artist name information that
can be stored in an MP3 file.
Ô
¯
Â
q Playback area
This shows the currently selected playback area.
ALL
All files in the MUSIC folder
8 Playback position
FOLDER All files in the selected folder
This bar shows the current playback position. As playback
proceeds, the darkened bar extends from the left.
P.LIST All files added to the playlist
34 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
w Elapsed time
Recording screen
This shows the elapsed time of the currently playing file
(hours: minutes: seconds).
When recording or when in recording standby, the screen
appears as follows.
e Remaining time
This shows the remaining time of the currently playing file
(hours: minutes: seconds).
r Playback file number/total number of files
This shows the total number of files in the playback area
and the current file number.
t Level meter
When MIC or LINE is ON (
or
), this shows the
volume level of the input signals.
1 Playback speed status
If the input level becomes too high, an indicator appears
briefly at the right end of the meter.
Depending on the playback speed setting, the icon
appears as follows. The recording speed, however, cannot
be changed.
When MIC or LINE input is OFF (
appears here.
or
), OFF
Normal playback speed
110–150% speed
50–90% speed
2 Prerecord or auto record function status
When prerecording is enabled and the unit is in recording
standby, “PRE”(
When the auto record function is enabled and the unit is
recording, “A.REC”( )appears here.
) appears here.
TASCAM LR-10 35
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
3 Key adjustment status
9 Level meter
This shows whether key adjustment is ON or OFF. Key
adjustment is disabled during recording
When MIC or LINE is ON (
volume level of the input signals.
or
), this shows the
: Key adjustment OFF
When MIC or LINE is OFF (
here.
or
), OFFappears
4 Recorder operation status
Depending on the recorder operation status, one of the
following icons appears.
Menu structure
ª
π
º
Recording standby
Paused
Press the MENU button to open the MENUscreen. The menu
contains the following items
Recording
Menu item
INFORMATION
PLAYLIST
Function
Pages
5 Recording capacity
View information about files, See on page 88.
the SD card and the system.
Edit the playlist.
Make playback interval and
repeat playback settings.
Make input settings
This shows the amount of the current SD card’s total
capacity that is used. As the amount of remaining capacity
decreases, the darkened bar extends from the left.
See on page 67.
See on page 64.
PLAYMODE
6 File name
See on page 48.
See on page 53.
INPUT SETTING
AUTO REC
This shows the name of the file that is being recorded.
Make automatic recording
function settings.
7 Elapsed recording time
This shows the elapsed time of the file being recorded
(hours: minutes: seconds).
Divide a file.
Make file name settings.
Make settings related to us-
ing a foot switch as a remote
control.
See on page 55.
See on page 85.
See on page 87.
DIVIDE
FILE NAME
8 Remaining recording time
FOOT SW
This shows the remaining amount of recording time
available (hours: minutes: seconds) on the current SD card
Make various unit settings.
See on page 83.
SETUP
Make date and time settings See on page 45.
DATE/TIME
36 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
Using the menu
This example shows how to use the menu to change the
repeat function.
1. Press the MENU button to open the MENUscreen.
4. Use the VALUE (+/–) buttons to change the setting.
2. Use the §/BROWSE and ¶/MIC buttons to select the
desired menu item, and press the Ábutton or ¯
button to open that setting screen.
5. Repeat steps 3 and 4 as necessary for the other items.
6. Press the MENU button to return to the MENUscreen.
Press the HOME button to return to the Home Screen.
3. Use the §/BROWSE and ¶/MIC buttons to select the
desired setting item. (When selected, the “:” becomes
“∑” and the setting value appears as light letters on a
dark background.)
TASCAM LR-10 37
Download from Www.Somanuals.com. All Manuals Search And Download.
2–Names and Functions of Parts
VALUE (+/-) buttons
Basic operations
Use to change value of the selected item.
Use the following buttons to use the setting screens.
RECORD [º] button
On the DIVIDEscreen, use to execute the division of a file.
MENU button
Press to open the MENUscreen. Press when the MENU
screen is open to return to the Home Screen.
Ábutton
Use this button to move from the MENUscreen to
the selected setting screen, and to select “YES”on a
confirmation pop-up message.
HOME button
When any of the setting screens is open, press the HOME
button to return to the Home Screen.
[ª] Button
Use to respond “NO”to a pop-up confirmation message.
§/BROWSE and ¶/MIC buttons
Use this button to move the cursor (change the
highlighted item) and to change the value of the selected
item.
Use this also to return from the FILEINFORMATIONpop-
up message when using the browse function.
¯button
Use this button to move from the MENUscreen to the
selected setting screen, to move the cursor (change the
highlighted item) right on a setting screen and to open a
folder on the BROWSEscreen.
Âbutton
Use this button to move the cursor (change the
highlighted item) left on a setting screen and to close the
open folder on the BROWSEscreen.
38 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Preparation
2. Insert the SD card into the SD card slot in the back of
the battery compartment in the direction shown in the
illustration until it clicks into the place.
Inserting and removing SD cards
Inserting an SD card
The SD card slot is inside the battery compartment on the
bottom of the case. Insert the SD card here.
NOTE
An SD card is already in the unit when it is purchased. You can
use this SD card as is for recording and playback. There is no
need to reinsert it.
1. Remove the battery compartment cover. If there are
batteries in the compartment, confirm that the unit
power is OFF and then remove them.
3. Insert the card and close the cover.
If you are using batteries, insert them first before closing
the cover
TASCAM LR-10 39
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Preparation
Removing an SD card
Press the inserted SD card in slightly to eject it.
Preparing an SD card for use
To use an SD card with this unit, you must format it by using
this unit first.
1. Confirm that an SD card is inserted, and press and hold
the
[ª] button on the top panel of the unit to turn
the power ON.
2. If a new card or a card that was formatted by a different
device has been inserted in the unit, the following pop-
up message appears.
CAUTION
Do not remove the SD card from the unit when it is
connected to a computer by USB.
•
•
•
SD cards that meet SD/SDHC standards can be used with
this unit.
A list of SD cards that have been verified to work with this
unit is posted on the TASCAM website (http://www.tascam.
com/).
3. Press the Ábutton to start formatting.
Remove the SD card if you do not wish to format it.
CAUTION
Formatting will erase all the data on the card.
4. After formatting completes, the Home Screen opens.
You can also reformat a card with this unit at any time.
40 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Preparation
Card write protection
SD cards have write-protection switches that prevent new
data from being written to them.
CAUTION
When formatting, use a TASCAM PS-P520 AC adaptor (sold
separately), USB bus power or confirm that the batteries have
sufficient remaining power.
Special cases
If you insert an SD card that has been formatted by a device
other than another LR-10, the FORMAT ERRORscreen will
appear. In this case, format the card to use it with this unit.
SD cards that have been formatted by a TASCAM DR series
device, however, are compatible with this model.
•
•
Unprotected
Protected
If you slide the protect switch to the “LOCK”position, file
recording and editing will not be possible. Move the switch to
the unlocked position in order to record, erase and otherwise
edit data on the card.
If the system file or another important file has been
accidentally erased from the SD card when accessing it
from a computer, the following pop-up screen appears.
In this case, press the Ábutton to format the card again.
TASCAM LR-10 41
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Preparation
When using AA batteries, set the type of battery in order
to allow the unit to accurately show the amount of power
remaining and determine whether enough power is available
for proper operation. (See “Setting the battery type”on page
83.)
Powering the unit
This unit can be powered by two AA batteries, USB bus power
or a TASCAM PS-P520 AC adaptor (sold separately).
This unit can use either alkaline or nickel-metal hydride
(NiMH) batteries.
CAUTION
Manganese batteries cannot be used with this unit.
•
•
Using AA batteries
This unit cannot recharge Ni-MH batteries. Use a commer-
cially-available recharger.
As described in the “Inserting and removing SD cards”section
above, this unit has a battery compartment in the bottom.
Insert 2 AA batteries into this compartment, aligning them
correctly with the plus/minus indications inside, and then
close the compartment cover.
The included alkaline batteries are provided for confirming
the operation of the unit and might not last very long.
•
Using USB bus power
Connect the unit with a computer using the included USB
cable as shown in the illustration below.
computer
USB
The USBSELECTscreen appears if the power is ON when you
make the USB connection or if you turn the power ON after
making the USB connection. This screen allows you to set
42 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Preparation
whether to use USB bus power (BUS POWER) or to connect
the unit’s storage to the computer (STORAGE).
Using an AC adaptor (sold separately)
Connect a TASCAM PS-P520 AC adaptor (sold separately),
which is designed for the power requirements of this unit, to
the DC IN 5V jack as shown in the illustration.
Use the §/BROWSE button or ¶/MIC button to select BUS
POWERand press the Ábutton to provide power from the
computer USB port and open the Home Screen.
TACAM
AC outlet
PS-P520
(sold separately)
DC plug
CAUTION
Connect this unit and the computer directly. Operation using
a USB hub cannot be assured.
NOTE
If you connect to a computer by USB, power will be supplied
from the USB bus even if batteries are also in the unit.
CAUTION
Never use any adaptor other than the TASCAM PS-P520 AC
adaptor (sold separately), because it is designed for the power
requirements of this unit. Use of a different adaptor could
cause malfunction, fire or electric shock.
NOTE
If batteries are installed and the AC adaptor is connected,
power will be supplied from the AC adaptor.
TASCAM LR-10 43
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Preparation
Startup and shutdown
®
CAUTION
Turn the volume of any monitoring system that is connected
to this unit down completely before turning the unit’s
power ON or putting it into standby. Do not wear connected
headphones when turning the unit’s power ON or putting it
into standby. Failure to follow these precautions could cause
noise, which might damage speakers or harm your hearing.
Startup Screen
Home Screen
Setting the power to standby
When the power is ON, press and hold the
until the INSTRUMENTAL TRAINER/RECORDERscreen
[ª] button
appears.
Turning the power on
When the unit is in standby mode, press and hold the
[ª]
button until the TASCAM LR-10startup screen opens.
The Home Screen opens after the unit completes startup.
44 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
3–Preparation
USB bus power or an AC adaptor. When using batteries, we
recommend that you replace or recharge them before they
completely lose power.
Setting the date and time
Using its internal clock, this unit remembers the date and time
when a file is recorded.
1
Press the MENU key to open the MENUScreen.
2
Use the §/BROWSE and ¶/MIC buttons to select
DATE/TIME, and press the Áor ¯button.
3
4
Use the Â/¯buttons to move the cursor, and use
the VALUE (+/–) buttons to change values.
Press the Ábutton to confirm the change and return
to the MENU screen.
NOTE
You can set the unit to automatically add the date and time to
file names. (See “Setting the file name format”on page 85.)
CAUTION
The date and time setting can only be maintained for a
few minutes when the unit is not powered by batteries,
TASCAM LR-10 45
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Connecting
Connecting monitoring equipment
Connecting with a computer
By connecting this unit with a computer, you can transfer
(copy) audio files (WAV or MP3 format) on the computer to
the SD card in the unit, as well as erase files and work with
folders on the card from the computer.
Headphones
Use the included USB cable to connect the USB port of this
unit to a USB port on the computer.
computer
USB
Powered monitor speakers or
amplifier and speakers
Connect headphones or a monitoring system (such as
powered speakers or an amplifier and speakers) to this unit’s
/LINE OUT jack.
When connected, the USB SELECTpop-up screen appears
on the unit.
CAUTION
Before connecting headphones, use the OUTPUT (–) button
to minimize the volume. Failure to do so could cause the
sudden output of loud sounds, which might lead to hearing
damage or other harm.
To exchange data with the computer, use the §/BROWSE or
¶/MIC button to select STORAGEand press the Ábutton.
USB connectedpop-up screen appears on the screen.
(Select BUS POWERto power the unit from the computer USB
bus.)
46 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
4–Connecting
Connecting an instrument
This unit appears on the computer screen as an external drive
named LR-10.
In addition to the built-in microphone, this unit has a line in
jack (stereo mini-jack) on its right side panel to which you can
connect the outputs of keyboards and other instruments, as
well as audio devices.
Keyboard
The LR-10 drive contains MUSIC and UTILITY folders.
Disconnecting from a computer
After using the correct procedures to dismount the LR-10
drive from your computer, disconnect the USB cable. The unit
should automatically turn off.
Please refer to the operation manual for your computer
system for instructions about the correct procedures for
dismounting an external drive.
NOTE
You can apply the built-in effects to sound input by the
connected instrument and play along to a song playing
back on the unit or its metronome.
•
•
To use an electric guitar or bass with this unit, connect the
instrument first to an effect pedal or other device that has
a headphones/line level output.
TASCAM LR-10 47
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
This unit can record a performance through the built-in mic or
from a keyboard or similar instrument that is connected to the
LINE IN jack. The audio file format used for recording is always
44.1 kHz, 16-bit WAV.
In addition, this unit can also mix the input signal and an
audio file that is playing back and record both together
(overdubbing).
This screen has the following setting items.
Use the §/BROWSE and ¶/MIC buttons to select the
desired item. (When selected, the “:”becomes “∑”
and the setting value appears as light letters on a dark
background.) Use the VALUE (+/–) buttons to change the
setting value.
Setting the location where recorded
files are saved
The GAIN, TYPE, LOW CUTand LEVEL CTRLitems only
You can set the location where recorded files are saved. (See
“Folder operations”on page 59.)
function when INPUTis set to MIC
.
INPUT:
If you do not set a destination, files will be saved directly in
the MUSIC folder.
Set the input source to microphone (MIC) or line (LINE).
The default setting is MIC
.
When MICis selected, sets the input source as the built-in
microphones.
Setting the input functions
When LINEis selected, sets the source as the line level
signal input to the right side panel LINE IN jack (stereo
mini-jack).
1
2
Press the MENU button to open the MENUScreen.
Use the §/BROWSE and ¶/MIC buttons to select
INPUT SETTING, and press the Áor ¯button to
open the INPUT SETTINGscreen.
GAIN:
Set the built-in microphones input sensitivity as HIGH
,
MID, or LOW
.
48 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
The factory default setting is MID
.
NOTE
Change it to HIGHif the input level is too low and to LOWif
the input level is too high.
Try using one of the low cut filter settings when recording
outdoors or another place where the unwanted sound of
wind is being recorded.
•
•
TYPE:
When recording live performances and in other situa-
tions where unexpected loud sounds might occur, set
this function to LMTto prevent input clipping and allow
recording without distortion.
Set the built-in microphones to STEREOor MONO. The
factory setting is STEREO
.
If you select MONO, the left and right channels are
combined into the same signal.
Use the LR-10’s built-in effects as necessary on the input
source signal. (See “Using the built-in effects”on page 78.)
•
LOW CUT:
The factory default setting of the low cut filter is OFF, but
you can also select 40Hz, 80Hzor 120Hzas the cut-off
frequency for a low cut filter.
Adjusting the input level
LEVEL CTRL:
Use this to set the level control function.
You can adjust the level of the mic/line input.
Use the INPUT volume control on the right side panel to
adjust the input level of the built-in microphones or the LINE
IN jack.
Set it to AUTOto have the LR-10 automatically adjust the
input gain according to the input level. Loud sounds and
quiet sounds are both adjusted to the same level.
Set it to LMTto have the LR-10 automatically limit the
input gain so that input level of loud sounds is reduced to
prevent distortion.
The factory default setting is OFF
.
3
Press the HOME button to return to the Home Screen.
TASCAM LR-10 49
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
The PEAK indicator to the right of the display lights red
just before the recording level begins to distort. Play the
instrument or start playback on the connected device, and
input the loudest volume you intend to record. Set the INPUT
level as high as possible without making the PEAK indicator
light red, and set the INPUT level as high as possible without
making the PEAK indicator light red.
When recording starts, the RECORD [º] button indicator
lights and the display shows the elapsed and remaining
recording times.
CAUTION
Press and hold the RECORD [º] button to enable the
pre-record function and put the unit into recording
standby. The RECORD [º] button indicator blinks when in
recording standby. (See “Recording a few seconds before
pushing the record button (pre-recording)”on page 51.)
In order to hear through headphones the sound that you are
recording from the built-in microphones or the line in jack,
the mic/line input must be ON (
or
). If the input is
off ( or ), press the ¶/MIC button to turn it ON (
or
).
2. Press the
[ª] button to stop recording.
The input can be turned ON/OFF during recording.
To pause recording, press the RECORD [º] button. To
resume recording to the same file, press the RECORD [º]
button again.
Recording
Press the
[ª] button after pausing to complete the
Before following these procedures, adjust the input level and
open the Home Screen.
creation of an audio file with the music recorded up to the
moment that recording was paused.
1. Press the RECORD [º] button briefly to start ordinary
recording.
50 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
TIP
Recording a few seconds before
pushing the record button (pre-
recording)
Use this function in combination with the auto-recording
function to record without missing the beginning of a
performance.
The unit can capture up to 2 seconds of input signal during
recording standby, allowing recording to start before the
RECORD [º] button is pushed.
NOTE
If the unit was put into recording standby less than 2 seconds
before this function is used, recording will start from the time
when recording standby was enabled.
1. Press and hold the RECORD [º] button briefly to start
recording standby. The RECORD [º] button indicator
blinks, and the PRE (
) icon appears on the display.
Recording the input sound with the
playback sound (overdubbing)
2. Press the RECORD [º] button again briefly to start
recording. Input signal is recorded starting up to 2
seconds before the button was pushed.
You can combine the input signal with the signal from an
already recorded file being played back to record a new file.
For example, you could record a new instrument part over an
existing track.
The RECORD [º] button indicator lights when recording.
3. Press the
[ª] button to stop recording.
To pause recording, press the RECORD [º] button. To
resume recording to the same file, press the RECORD [º]
button again.
NOTE
When overdubbing, You cannot use the auto-record or
manual file incrementation functions.
•
Press the
[ª] button after pausing to complete the
You cannot pause during overdubbing. (The RECORD [º]
button does not respond if pushed.)
creation of an audio file with the music recorded up to the
moment that recording was paused.
•
TASCAM LR-10 51
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
4. Press the Ábutton while pressing and holding the
TIP
RECORD [º] button to begin overdubbing.
Using the overdubbing function, you can record over the
same file multiple times, allowing you to use this unit as a
simple multitrack recorder.
CAUTION
If you press and hold the RECORD [º] button long , the unit
will be put in recording standby with the pre-record function
enabled, and overdubbing will not be possible.
Overdubbing
1. Use the Âbutton, ¯ button or the BROWSEscreen
to select the file that you want to overdub.
5. When overdubbing starts, the RECORD [º] button
indicator lights, and the elapsed and remaining
recording times are shown on the recording screen.
In addition, the name of the file being played back is
shown next to the play icon and above the name of the
file being recorded.
2. Press the Ábutton to start playback and begin playing
the instrument. Check the balance between the levels
of the playback and instrument sounds.
3. Use the INPUT volume to adjust the input volume
level so that the PEAK indicator does not light. Press
the BALANCE button to show the BALANCE item, and
use the VALUE (+/–) buttons to adjust the level of the
playback sound. The range is from “0” (minimum) to
“20” (maximum), and the default value is “20”.
If no file that can be played back has been selected, the
following pop-up message appears.
NOTE
The BALANCEsetting only affects the volume when MIC or
LINE is ON (
), changing the BALANCEvalue has no effect on the
volume.
or
). When MIC or LINE is OFF (
or
52 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
6. Press the
[ª] button to stop recording.
Starting and pausing recording
automatically (AUTO REC)
5. Press the §/BROWSE or ¶/MIC button to select the
STARTLEVELitem.
This unit can be set to automatically start and pause recording
in response to the level of the input signal.
6. Use the VALUE (+/–) buttons to set the input signal
1. Press the MENU button to open the MENU screen.
detection level to -6dB, -12dB(default value), -24dBor
-48dB
.
2. Use the §/BROWSE and ¶/MIC buttons to select the
AUTO REC menu item, and press the Áor ¯ button
to open the AUTO RECscreen.
7. After completing the setting, press the HOME button to
return to the Home Screen.
3. Use the §/BROWSE and ¶/MIC buttons to select the
8. Press the RECORD [º] button to start recording standby
MODEitem.
and RECORD [º] button indicator blinks.
4. Use the VALUE (+/-) buttons to set it to ON
.
Press and hold the RECORD [º] button to enable the
pre-record function and put the unit into recording
standby.
TASCAM LR-10 53
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
Recording starts automatically when the input signal level
exceeds the detection level set using the STARTLEVEL
item.
Track incrementation
You can start recording to a new file without interruption
manually. If a file reaches the maximum size (2GB), the unit
will also automatically start recording to a new file. In both
cases, the original file is saved and no gap occurs in the
recording.
Recording stops automatically and the unit returns to
recording standby when the input signal level stays below
the detection level set using the STARTLEVELitem for five
or more seconds and RECORD [º] indicator blinks.
TIP
Manual track incrementation during
recording
Use this function in combination with the pre-recording
function to record without missing the beginning of a
performance.
At any time during recording, you can manually start a new
file and continue recording easily.
NOTE
1. Press the ¯button during recording.
When AUTORECis ON, unlike usual, pressing the RECORD [º]
button briefly does not start recording, but does put the unit
into recording standby.
CAUTION
A new file cannot be created if the total number of files and
folders would exceed 5000.
•
9. You can press the
[ª] button if you want to stop a
recording that has started automatically.
Files shorter than two seconds cannot be created.
•
•
If the name of a newly created file would be the same as
that of an existing file, the number at the end of the name
is increased to give the new file a unique name.
CAUTION
When overdubbing, the auto-recording function cannot be
used.
When overdubbing, the track incrementation function
cannot be used.
•
54 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
3. Use the §/BROWSE and ¶/ MIC buttons to select the
DIVIDEmenu item, and press the Ábutton or ¯
button to open the DIVIDEscreen.
NOTE
When a new file is created, the number at the end of the name
is increased.
Automatic track incrementation by file size
If a file reaches the maximum size (2 GB) during recording,
the unit will automatically start recording to a new file. The
original file is saved and no gap occurs in the recording.
4. Use the Ôand button to determine where the
CAUTION
file will be divided, and press the RECORD [º] button.
A new file cannot be created if the total number of files and
folders would exceed 5000.
The following pop-up message appears.
NOTE
If the recording time is 24 hours or more, it will be displayed
as 23:59:59.
5. Press the Ábutton to divide the file.
Dividing files (DIVIDE)
Press the
[ª] button to cancel division and return to
You can split a recorded file into two files at any position you
like.
the DIVIDEscreen.
1. Use the Âbutton, ¯button, or BROWSEscreen to
select the file that you want to divide.
2. Press the MENU button to open the MENUscreen.
TASCAM LR-10 55
Download from Www.Somanuals.com. All Manuals Search And Download.
5–Recording
NOTE
Recording duration
The table below shows the approximate amount of recording
time possible on SD/SDHC cards of different capacities.
When the DIVIDEscreen is open, you can press the Á
button and set the divide position while playing the track.
•
•
After dividing a file, two new files with “_a”and “_b”
added to the end of the original file name are created. For
example if the original filename is “LR0000_0000.wav”then
the new files will be named “LR0000_0000_a.wav”(the
recording before the division point) and “LR0000_0000_
b.wav”(the recording after the division point).
SD/SDHC card capacity
1 GB
2 GB
4 GB
8 GB
Approximate
recording time
(hours: minutes)
1: 41
3 : 22
6 : 44
13 : 28
The recording times shown above are estimates. They
might differ depending on the SD/SDHC card being used.
•
•
CAUTION
MP3 files cannot be divided.
•
•
The recording times shown above are not continuous
recording times, but rather they are the total possible
recording times for the SD/SDHC card.
Division is not possible if the SD card has insufficient open
space.
Division is not possible if the file name would become
more than 200 characters long.
•
•
This unit only records in 44.1 kHz, 16-bit WAV format.
•
Division is not possible if a file that already exists has the
same name as the name that would be given to a new file
created by division.
56 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
6–Working with Files and Folders (BROWSE screen)
On the Browse Screen, you can view the contents of the
MUSIC Folder, which contains the audio files on the SD card.
BROWSE screen navigation
On this screen, you can also play and erase selected audio
files, create folders, add tracks to the playlist and so on. (See
“Playlist”on page 67.)
On the BROWSEscreen, folders and music files appear in
a hierarchical structure much like they would appear on a
computer. Folders can only be used to two levels.
TIP
Use the §/BROWSE and ¶/MIC buttons to select files and
folders.
•
•
•
If you connect this unit with a computer by USB or connect
the SD card directly with a computer, you can change the
folder structure within the MUSIC Folder and erase files in it
using the computer. Furthermore, you can change file names
from the computer.
When a folder is selected, press the ¯button to show
the contents of that folder.
When a file or folder is selected, press the Âkey to exit
the currently open folder and go to a higher level in the
folder structure.
To open the BROWSEscreen, from the Home Screen, press the
§/BROWSE button.
When a file or folder is selected, press the Ákey to open
the pop-up window.
•
Icons on the BROWSE screen
When you open the BROWSEscreen, the contents of the folder
that contains the file that was selected on the Home Screen
are shown.
The icons that appear on the BROWSEScreen have the
following meanings.
MUSIC folder (
)
The MUSIC Folder is the highest (root) level folder in the
hierarchy shown on the BROWSEScreen.
TASCAM LR-10 57
Download from Www.Somanuals.com. All Manuals Search And Download.
6–Working with Files and Folders (BROWSE screen)
PLAY
Play the file and reopen the Home Screen. If the playback
Audio file (
)
This icon appears before the names of audio files.
area is set to “FOLDER”, the playback area becomes the
folder that contains that file.
Folder (
)
This icon shows folders that contain subfolders.
INFO
Show information (date, time and size) about the selected
Folder (
)
This icon shows folders that do not contain subfolders.
file. Press the Ábutton again or press the
[ª] button
to return to the BROWSEscreen.
Open folder (
)
The contents of the folder marked with this icon are
currently shown on the screen.
File operations
ADD LIST
Select the desired audio file on the BROWSEscreen, and press
the Ábutton to open the following pop-up menu.
Add the selected file to the playlist. (See “Playlist”on page
67.)
DELETE
A message appears to confirm that you want to delete the
selected file. Press the Ábutton to delete the file and the
[ª] button to cancel deletion.
Use the §/BROWSE and ¶/MIC buttons to select the desired
item, and press the Ábutton to execute one of the following
operations.
58 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
6–Working with Files and Folders (BROWSE screen)
CANCEL
No operation is conducted on the selected file and the
pop-up menu closes.
SELECT
Return to the Home Screen and select the first file in
the folder. This folder becomes the new playback area
regardless of the previous playback area setting.
When recording, files are created in the folder selected
Folder operations
using this operation.
CREATE
Select the desired folder on the BROWSEscreen, and press the
A pop-up appears to confirm that you want to create a
new folder.
Ábutton to open the following pop-up menu.
Use the §/BROWSE and ¶/MIC buttons to select the desired
item, and press the Ábutton to execute one of the following
operations.
Press the Ábutton to create a new folder, or press the
[ª] button to cancel the operation.
However, if you try to create a new folder inside a second
level subfolder the Layer too Deepmessage appears
and the folder is not made.
TASCAM LR-10 59
Download from Www.Somanuals.com. All Manuals Search And Download.
6–Working with Files and Folders (BROWSE screen)
ALL DEL
Delete the selected playback file
(QUICK DELETE)
A pop-up message appears to confirm that you want to
delete all the files in the selected folder at once.
Use the following procedure to conveniently delete the
currently selected playback file.
1. On the Home Screen, press and hold the §/BROWSE
button to open the QUICK DELETEscreen.
Press the Ábutton to erase the files, or press the
button to cancel the operation.
[ª]
2. Press the Ábutton again to confirm deletion, or press
the
[ª] button to cancel.
NOTE
You cannot erase read-only files or files that are not
recognized by this unit.
CANCEL
No operation is conducted and the selected folder is left
as is.
60 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
7–Playback
When the Home Screen is open , use Á, Â, ¯and other
buttons to operate the unit in the same way you would use a
CD player or other audio playback device.
Stopping playback
When the Home Screen is open and a track is playing back,
press the [ª] button to stop playback at the current
position (pause).
When the Home Screen is not open, however, these buttons
have different functions.
Before using the following procedures, insert an SD card that
has been formatted by this unit and that contains audio files
that the unit can playback.
Press the
the file.
[ª] button again to return to the beginning of
NOTE
Selecting a file
SD cards that have been formatted by a TASCAM DR series
device can also be used with this unit.
During playback or when stopped, use the Âand ¯
buttons to select a file.
Press the Âbutton to skip to the previous file.
Playback
Press the ¯ button to skip to the next file.
When the unit is stopped, press the Á button to start
playback.
Only files in the playback area can be played. (See “Using the
PLAY MODE screen to set the playback area”on page 6.)
The song name, file number and other information for the
currently playing file are shown on the display.
NOTE
Only files in the playback area can be played.
•
•
The ªicon appears on the display when playback is stopped
at the beginning of a track, and the πicon appears when
playback is stopped in the middle of a track (paused).
You can also choose files for playback by name on the
BROWSEscreen.
TASCAM LR-10 61
Download from Www.Somanuals.com. All Manuals Search And Download.
7–Playback
Searching forward and backward
Adjusting the playback volume
During playback or when stopped (or paused), press and hold
the Ô/button to search backward/forward. Release
the button to return to the previous state.
Use the OUTPUT (+/–) buttons to adjust the volume level
output from the built-in speaker or the /LINE OUT jack.
While being adjusted, the volume level is shown in a pop-up
at the bottom of the display.
Use the CUE/REVSPEEDitem on the SETUPscreen to set the
search speed. (See “System settings (SETUP)”on page 83.)
Press the Ô/ button briefly to search backward/
forward to the beginning/end of the file.
Press the same button again briefly to change the search
speed. The speed options are: x2, x5, x10, x20, x40 and x120.
NOTE
If you turn the MIC/LINE input off, the playback level returns
to its original level.
NOTE
Searching backward/forward continues only until the
beginning/end of the current file. Searching will not continue
into the previous or next file even if you continue to hold the
button.
If the MIC/LINE input is on, and you have used the BALANCE
button to lower the volume of the playback (BALANCE
)
to overdub an audio file, when you play back that file, the
playback monitoring level will be lower than it was when
recording. In this case, use the BALANCE button to set
BALANCEto its maximum.
62 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
7–Playback
Disabling the MIC/LINE input
Adjusting the balance between
playback and input signals
When you want to listen to just the playback signal, you can
disable the MIC/LINE input to prevent any unwanted noise.
You can adjust the balance between the input sound of an
instrument being played and the playback sound of a file.
If you want to disable the MIC/LINE input (built-in
microphones or LINE IN jack), press the¶/MIC button when
the Home Screen is open so that the MIC or LINE icon appears
Use the INPUT volume to adjust the level of the input signal,
and press the BALANCE button to open the BALANCEitem
and adjust the level of the playback signal.
as dark letters on a light background (
or
).
Press the ¶/MIC button again to enable the MIC/LINE input.
The MIC/LINEicon appears as light letters on a dark
background (
or
) when input is enabled.
NOTE
If you turn the MIC/LINE input off (
in the level meter area.
or
), OFFappears
Adjust the volume of the playback sound using the VALUE
(+/–) buttons. The range is from “0”(minimum) to “20
”
(maximum), and the default value is “20”.
NOTE
The BALANCEsetting only affects the volume when MIC or
LINE is ON (
), changing the BALANCEvalue has no effect on the
volume.
or
). When MIC or LINE is OFF (
or
When the MIC/LINE input is off (
or
), the BALANCE
setting is canceled and the playback level returns to its
original setting.
TASCAM LR-10 63
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Playback Area and Playlist
On the Home Screen, use the Âor ¯ button to select
a file from the current “playback area”to play. You can set the
playback area that includes the files that can be selected. If
the card contains a large number of files, for example, setting
a limited playback area can make file selection easier. On the
PLAY MODEscreen, you can set the playback area to all files,
the current folder or the playlist. You can also use the BROWSE
screen to set the desired folder as the playback area.
3. Select the AREAitem so that its setting value appears as
light letters on a dark background.
4. Use the VALUE (+/–) buttons to select one of the
following playback areas.
NOTE
On the BROWSEscreen, you can also choose any file on the
card for playback regardless of the playback area setting.
ALL FILES
Allow playback of all the files in the MUSIC folder on the SD
card.
Using the PLAY MODE screen to set
the playback area
FOLDER
Allow playback of all the files in the folder that contains the
currently selected file.
Follow these procedures to set the playback area on the PLAY
MODEscreen.
PLAYLIST
Allow playback of the files in the playlist. (See “Playlist”on
page 67.)
1. Press the MENU button to open the MENUscreen.
If you select this, but there is no playlist defined, a No
PLAYLISTpop-up appears.
2. Use the §/BROWSE and ¶/MIC button to select PLAY
MODEand press the Ábutton or ¯button to open
the PLAYMODEscreen.
64 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Playback Area and Playlist
Selecting a folder for the playback
area (1)
Regardless of the current playback area, if you select a folder
on the BROWSEScreen, the playback area changes to the
selected folder.
Even if there is no playlist, you can still set the playback
area to PLAYLIST. Doing so, however, will cause the No
PLAYLISTpop-up to appear every time you press the
Âor ¯ button because you cannot change to
another file.
1. On the Home Screen, press the §/BROWSE button to
open the BROWSE screen.
2. Use the §/BROWSE and ¶/MIC buttons to select the
NOTE
desired folder (light on dark).
The current playback area setting (ALL, FOLDERor P.LIST) is
shown at the bottom left of the Home Screen.
For instructions about using the BROWSEscreen, see
“BROWSE screen navigation”on page 57.
3. Press the Ábutton to open the pop-up menu shown
below.
Playback area indication
TASCAM LR-10 65
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Playback Area and Playlist
3. Press the ¯button to show the contents of that
Use the §/BROWSE and ¶/MIC buttons to choose the
SELECT, and to press the Ábutton.
folder.
4. The Home Screen automatically reopens and the first
file in that folder is selected. This folder becomes the
playback area regardless of the previous playback area
setting.
4. Use the §/BROWSE and ¶/MIC buttons to select the
Selecting a folder for the playback
area (2)
desired file (light on dark).
For instructions about using the BROWSEscreen, see
“BROWSE screen navigation”on page 57.
If the playback area is set to FOLDERand you select a file on
the BROWSEscreen, the folder that contains the selected file
becomes the playback area.
5. Press the Ábutton to open the pop-up menu shown
below.
1. On the Home Screen, press the §/BROWSE button to
open the BROWSEscreen.
6. Use the §/BROWSE and ¶/MIC buttons to choose the
PLAY(light on dark), and to press the Ábutton.
2. Use the §/BROWSE and ¶/MIC buttons to select the
The Home Screen automatically reopens and that file starts
playing back. Moreover, the folder that contains that file
becomes the playback area regardless of the previous
playback area setting.
desired folder (light on dark).
66 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Playback Area and Playlist
Playlist
You can make a playlist, which is a set of tracks for playback.
You can play just the tracks in your playlist by setting the
AREAitem to PLAYLISTon the PLAY MODEScreen.
For more information about selecting files, see “BROWSE
screen navigation”on page 57.
In addition, when the playback area is set to PLAYLIST, loop
playback has additional functions. (See “Using loop playback
with the playlist”on page 73.)
3. Select ADDLIST, and press the Á button to add that
file to the playlist. The pop-up menu closes.
Adding files to the playlist
4. Repeat steps 2 and 3 as necessary.
1. On the Home Screen, press the §/BROWSE button to
Numbers are assigned to the files in the order that they are
added to the list.
open the BROWSEscreen.
Editing the playlist
You can view the playlist you have made on the PLAYLIST
Screen. On this screen, you can also play files and edit the
playlist
NOTE
1. Press the MENU button to open the MENUscreen.
For more information about the BROWSEscreen, see Chapter 6
“Working with Files and Folders (BROWSE screen)”on page 57.
2. Use the §/BROWSE and ¶/MIC buttons to select the
PLAYLISTmenu item, and press the Ábutton to open
the PLAYLISTscreen.
2. Select the file that you want to add to the playlist and
press the Ábutton to open the following pop-up
menu.
TASCAM LR-10 67
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Playback Area and Playlist
For this operation, it does not matter which track you
select in step 3. All the files are removed from the playlist,
but they are not erased from the SD card.
3. Use the §/BROWSE and ¶/MIC buttons to select the
file that you want to edit, and press the Ábutton to
open the pop-up menu.
DELETE
Remove the selected track from the playlist.
The file is removed from the playlist, but it is not erased
from the SD card.
CAUTION
4. Use the §/BROWSE and ¶/MIC buttons to select the
desired item, and press the Ábutton to execute the
operation.
No confirmation pop-up message appears before this
operation.
PLAY
Play the file and return to the Home Screen.
ALL CLR
A confirmation message appears to confirm that you want
to remove all the files from the playlist. Press the Ábutton
to remove all the files or the
operation.
[ª] button to cancel this
68 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
8–Playback Area and Playlist
MOVE
Select this to change the order of files in the playlist.
CANCEL
No operation is conducted on the selected file, and the
pop-up menu closes.
In addition to the file name, the file number also appears
light on dark.
1. Use the §/BROWSE and ¶/MIC buttons to move the
file to a different position in the playlist.
In the above example, the file in the 4th position has
been moved to the 3rd position.
2. Press the Ábutton to complete the movement and
return to the ordinary PLAYLISTscreen. (The file
number no longer appears light on dark.)
TASCAM LR-10 69
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Special Playback (playback control function)
Using this unit’s playback control functions, you can change
the speed of playback without changing the pitch and vice
versa. You can use these playback control functions for
effective practice and learning new parts.
Changing the speed
Changing the key
You can use the SPEED function to set the playback speed.
You can use the KEY function to change the pitch of playback
in semitone intervals (and the FINE TUNE function to change it
in cents) without changing the speed.
This unit has a Variable Speed Audition (VSA) function, so
even when playback speed is changed the pitch stays the
same.
Press the KEY button to show the KEYsetting area at the
bottom of the Home Screen on the display. Press the KEY
button again to show the FINETUNEsetting area.
Press the SPEED button to show the SPEED setting area at the
bottom of the Home Screen.
Use the VALUE (+/–) buttons to set the playback speed.
KEY can be set in a range of 6 semitones (â6–ã6). (The
default value is 0.)
The speed can be set in a range between 50% (x0.5) and
150% (x1.5) of the original speed in 10% increments (default
value: x1.0).
If you change the key to any value besides 0, the key change
function turns ON and the KEY icon (
) appears on the
When the SPEEDis set from x0.5–x0.9, the
shown, and when it is set from x1.1–x1.5, the
shown.
icon is
icon is
Home Screen as light letters on a dark background.
70 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
9–Special Playback (playback control function)
Set the amount of time to go back using the FLASHitem.
1. Press the MENU button to open the MENUscreen.
2. Use the §/BROWSE and ¶/MIC buttons to select the
PLAY MODEmenu item.
Use the FINE TUNEfunction to adjust the pitch by small
amounts.
3. Press the Ábutton or ¯button to open the PLAY
MODEscreen.
4. Use the §/BROWSE and ¶/MIC buttons to select
FLASH(setting value appears light on dark).
Use this to adjust the pitch up or down in cents (100 cents = 1
semitone) in a range of 50. (The default value is 0.)
NOTE
5. Use the VALUE (+/–) buttons to set the flashback time
in a range from 1–10 seconds, in one-second intervals.
(Default value: 2seconds)
Even if you use the FINE TUNE function to adjust the key, as
long as the KEY item setting is 0, the
as light letters on a dark background on the Home Screen.
icon will not appear
6. After completing the setting, press the HOME button to
return to the Home Screen.
Jump back a set amount and
continue playback (flashback)
During playback, press the Ábutton to use the flashback
function. This jumps back a few seconds and continues
playback.
TASCAM LR-10 71
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Loop Playback/Repeat Playback/Single Track Playback
In ordinary playback mode, unless you do something to stop
it, once playback starts, it will stop only when the end of the
last file in the current playback area is reached. By making
the settings and conducting the operations described in this
chapter, however, you can also make the unit loop a section
of a file that you choose, repeat all the files in the current
playback area, play a single track repeatedly or play a single
track once and stop.
The current position is set as the OUT (ending) point, and
loop playback between the IN (starting) and OUT (ending)
points begins.
The current positions of the IN (starting) and OUT (ending)
points are shown by the and icons that appear below
the playback position display bar on the Home Screen.
•
•
NOTE
Accurate assignment of IN (starting) and OUT (ending) points
is not always possible for variable bit rate (VBR) MP3 files.
During loop playback the
icon also appears.
To stop loop playback, press the LOOP button. This also
clears the loop interval setting.
Using loop playback (standard
mode)
3. Press and hold the LOOP button to open the LOOPSET
pop-up.
Use this function to continuously repeat playback (loop) part
of a file that you select.
1. During playback (or when paused), press the LOOP
button to set the point where you want to start loop
playback.
4. Use the Á, Ô, and
[ª] buttons to move the
The current position is set as the IN (starting) point.
IN (starting) point to the desired position. Press the
Âbutton to save the IN (starting) point.
2. Press the LOOP button at the point when you want loop
playback to stop.
72 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Loop Playback/Repeat Playback/Single Track Playback
6. Press the LOOP button briefly to start loop playback.
NOTE
When the LOOP SETpop-up window is open, press the Á
•
•
•
button to playback, press
Ôor button briefly to search the file.
[ª]button to, and press the
Press and hold the Ôor button to move the IN
(starting) or OUT (ending) point. (This is not possible when
there is no IN (starting) and OUT (ending) point.)
Press the
[ª] button during playback to pause, and
Using loop playback with the playlist
press the HOME button when paused to returned to the
Home Screen.
When the playback area is set to playlist, up to 5 loops with
distinct IN (starting) and OUT (ending) points can be set per
file.
5. Next, use the same buttons to move the OUT (ending)
point to the desired position, and press the ¯
button to save the OUT (ending) point.
Follow the procedures below to set and play back loops of
desired intervals in a file.
Loop settings for a file are saved until it is removed from the
playlist.
1. Press the LOOP button to show the LOOP setting area
at the bottom of the display. The word LOOPis followed
by a number. Use the VALUE (+/–) buttons to set the
NOTE
Use the Âand ¯buttons to switch between IN
(starting) and OUT (ending) points.
•
number to 1
–
5.
TASCAM LR-10 73
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Loop Playback/Repeat Playback/Single Track Playback
Press the
[ª] button during playback to pause, and
•
press the HOME button when paused to returned to the
Home Screen.
4. Next, use the same buttons to move the OUT (ending)
point to the desired position, and press the ¯button
to save the OUT (ending) point.
2. Press and hold the LOOP button to open the LOOPSET
pop-up.
NOTE
3. Use the Á, Ô, and
[ª] buttons to move the
Use the Âand ¯buttons to switch between IN
(starting) and OUT (ending) points.
IN (starting) point to the desired position. Press the
Âbutton to save the IN (starting) point.
5. Press the LOOP button briefly to start loop playback.
NOTE
When the LOOP SETpop-up window is open, press the Á
•
•
button to playback, press
[ª]button to, and press the
Ôor button briefly to search the file.
Press and hold the Ôor button to move the IN
(starting) or OUT (ending) point. (This is not possible when
there is no IN (starting) and OUT (ending) point.)
Turning loop playback on and off
Press the LOOP button briefly to turn loop playback ON or
OFF.
74 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
10–Loop Playback/Repeat Playback/Single Track Playback
When you want to restart loop playback, press the LOOP
button briefly to start loop playback of the last used loop.
3. Use the §/BROWSE and ¶/MIC buttons to select the
REPEATitem, and use the VALUE (+/–) buttons to set the
playback mode.
In the LOOP setting area shown at the bottom of the display,
the word LOOPis followed by a number, which shows the
current loop. Use the VALUE (+/–) buttons to change the loop
number. During loop playback, you can change this number
to start loop playback of a different loop if the loop assigned
to that number has IN (starting) and OUT (ending) points set.
OFF (default)
Play all tracks in the playback area in sequence. (This is the
ordinary playback mode.)
SINGLE
Play one file without repeating.
The
icon appears on the Home Screen.
Repeat and single track playback
1 REPEAT
You can repeatedly play back the current file (one file) or
multiple files within the designated playback area. You can
also play just one file.
Play the currently playing file repeatedly.
The icon appears on the Home Screen.
ALL REPEAT
1. Press the MENU button to open the MENUscreen.
Play all the files in the selected playback area repeatedly.
2. Use the §/BROWSE and ¶/MIC buttons to select PLAY
The
icon appears on the Home Screen.
MODEand press the Ábutton or ¯button.
NOTE
If you start loop playback, the REPEATitem automatically
switches to OFFif it is in a different mode.
TASCAM LR-10 75
Download from Www.Somanuals.com. All Manuals Search And Download.
11–Transferring songs to and from a computer
You can transfer audio files from a computer by USB, and play
them back for practice, to learn new parts and to overdub.
Copying audio files from a computer
Moreover, this unit can play back MP3 (32–320 kbps, 44.1 kHz)
and WAV (44.1 kHz, 16/24-bit) audio file formats.
1. Connect the unit to the computer. (See “Connecting
with a computer” on page 46.)
NOTE
2. Click the LR-10 drive that appears on the computer to
Instead of using USB to connect this unit and a computer, you
can also conduct the same operations by removing the SD
card from this unit and connecting it directly to a computer
that has a built-in SD card slot or by using a card reader.
open it, revealing UTILITY and MUSIC folders.
3. Drag-and-drop the desired audio files from the
computer to the MUSIC folder to copy those files to the
SD card.
Preparing audio files on a computer
Use the abilities of your computer OS or a software
application to copy music files from a CD or other source to
your computer.
When copying files to your computer, choose file types that
this unit can handle (the MP3 and WAV files types listed
above).
76 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
11–Transferring songs to and from a computer
4. After you finish copying files and closing the connection
Transferring audio files to a
computer
with the unit SD card from the computer, disconnect
the USB cable. (Please refer to the operation manual
for your computer system for instructions about the
correct procedures for dismounting an external drive.)
The unit will automatically turns off.
1. Click the LR-10 drive that appears on the computer to
open it, revealing UTILITY and MUSIC folders.
2. Open the MUSIC folder, and drag and drop the files
that you want to copy to the desired location on the
computer.
TIP
You can also manage the contents of the MUSIC folder on an
SD Card from a computer.
You can create up two levels of sub-folders inside the MUSIC
folder. Since you can set the unit to only play the contents of
a specific folder, you can conveniently organize tracks into
musical categories and artists. (See “Folder operations”on
page 59.)
Name the sub-folders and music files as you like, and these
names will appear on the unit’s display.
TASCAM LR-10 77
Download from Www.Somanuals.com. All Manuals Search And Download.
12–Using the built-in effects
This unit has built-in effects that can be applied to the input
signal during both practice and recording.
Use the Â/¯buttons to select the desired item. (When
selected, the setting value appears as light letters on a dark
background.) Use the VALUE (+/–) buttons to change the
setting value.
Turning the effects ON and OFF
REVERB
Select the type of reverb to use.
Press the EFFECT button briefly to turn the effects ON or OFF.
When ON, the effect last set on the EFFECTScreen becomes
LEVEL knob
active, and the FX icon (
dark background.
) appears as light letters on a
Use the REVERB item to adjust the output level of the selected
reverb type.
TIME knob
Use the PRESETitem to adjust the reverb time of the selected
reverb type. The reverb time range is set optimally for each
type of reverb. For this reason, the length of the reverb might
differ between reverb types even with the same setting value.
SOURCE
Setting the effect
Use this to set whether the effect is applied to the input signal
(INPUT) or the playback signal (PLAY).
Press and hold the EFFECT button to open the EFFECT
screen.
The default setting is PLAY
.
78 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
12–Using the built-in effects
Reverb List
Reverb type
Effects
This is a bright reverb modeled after a large hall-
like space.
HALL 1
This is a warm reverb modeled after a large hall-
like space.
HALL 2
ROOM
This reverb is modeled on a small indoor space.
This reverb is modeled on a studio-like space
This is a bright plate reverb.
STUDIO
PLATE 1
PLATE 2
This is a warm plate reverb.
TASCAM LR-10 79
Download from Www.Somanuals.com. All Manuals Search And Download.
13–Using the tuner
This unit has a built-in tuner. By inputting the sound of an
instrument, you can use the tuning meter on the display to
tune that instrument accurately. In addition, you can output a
tone for tuning from the built-in speaker or the /LINE OUT
jack, which is convenient for tuning multiple instruments
simultaneously, for example.
3. The first item shown for each mode is CALIB. Use this to
set the frequency of A between 435 Hz and 445 Hz.
The setting value is shown on the right side of the screen.
This setting is the same for both tuner modes.
Use of each tuner mode is explained below.
Preparation
1. Press the TUNER button to open the TUNER screen.
NOTE
The signal input through the left MIC/LINE input channel is
used for tuning. When using the built-in microphones to tune
acoustic guitars and other instruments that have rapid sound
decay, in particular, tune the instrument as close to the left
built-in microphone as possible.
2. The MODEitem is shown. Use the
Ábutton to select the tuner mode. The options are
AUTO ( [ª] : chromatic tuner mode) and OSC. (Á :
[ª] button and
oscillator mode).
After selecting the mode, press the TUNER button again to
make settings for that mode.
80 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
13–Using the tuner
Chromatic tuner mode (AUTO)
Oscillator mode
This is the default mode. Watch the tuning meter on the unit’s
screen as you tune your instrument. AUTOappears in the
upper right. The tuning meter and input signal pitch name
appear on the screen. (---appears when there is no input).
The built-in oscillator can output a tone for tuning through
the built-in speaker or the /LINE OUT jack. The tuning pitch
can be set in a three-octave range (C3–B5). OSC.appears in
the upper right.
1. Input the signal of the instrument that you want to
tune. The name of the closest pitch appears in the
upper part of the meter.
2. Tune the instrument until the desired pitch is shown
and the center of the meter is highlighted.
In addition to the CALIBitem described above, the oscillator
mode has the three other setting items that follow. Press the
TUNER button to cycle through the setting items.
A bar appears to the left if the tuning is too low and a bar
appears to the right if it is too high. The longer the bar is
the more out of tune the instrument is.
OSC NOTE
Set the pitch of the tuning tone (C3–B5).
OSC LEVEL
Set the output level of the tone between 0 and 10 (default
value 7).
TASCAM LR-10 81
Download from Www.Somanuals.com. All Manuals Search And Download.
14–Using the Metronome
This unit has a metronome function that is convenient for
practicing an instrument.
LEVEL
Set the metronome volume between 0and 10. The default
value is 5
.
Setting the metronome
Starting and stopping the
metronome
1. Press the METRONOME button to open the METRONOME
screen.
When the METRONOMEscreen is open, press the Ábutton to
start or stop the metronome.
NOTE
When the METRONOMEscreen is open, press the HOME button
to stop the metronome and return to the Home Screen.
Set the following items on this screen.
Press the METRONOME button again to change the item.
Use the VALUE (+/–) buttons to change the setting value.
TEMPO
Set the speed to a value between 20and 250beats per
minute (BPM). The default value is 120
BEAT
Set the accent frequency between 0and 9. There is no
.
accent when set to 0. The default value is 4
.
82 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
15–System settings
Setting the forward/backward search
speed
Use the CUE/REV SPEEDitem to set the speed of forward/
backward searching when pressing and holding the
Ô/button during audio file playback.
System settings (SETUP)
On the SETUPScreen, you can change various settings
according to your use environment and other requirements.
You can also initialize and format the SD card.
To access the SETUPscreen, press the MENU button to open
the menu list, select the SETUPitem using the §/BROWSE
and ¶/MIC buttons and press the Á button or ¯button.
Options: x2, x4, x8(Default value), x10
Setting the automatic power off time
Use the AUTO OFFitem to set the time before the unit power
automatically turns OFF after the last activity or operation
when powered by the internal battery.
Options: OFF(Default value), 3min, 5min, 10min, 30min
You can make the following settings on the SETUPscreen.
Adjusting the display contrast
Use the §/ BROWSE and ¶/MIC buttons to select the desired
item. (When selected, the “:”becomes “∑”and the setting
value appears as light letters on a dark background.) Use the
VALUE (+/–) buttons to change the setting value.
Use the CONTRASTitem to adjust the display contrast.
Range: 1–20(Default value: 5
)
Setting the battery type
Use the BATTERY TYPEitem to set the kind of batteries
used in the unit. This setting is used to show the amount of
remaining battery charge and to determine if the unit has
enough power for normal operation.
Options: ALKAL(alkaline batteries, default value), Ni-MH
(nickel-metal hydride batteries)
TASCAM LR-10 83
Download from Www.Somanuals.com. All Manuals Search And Download.
15–System settings
2. Press the Ábutton to open a confirmation pop-up
Restoring the default values (factory
settings)
Use the INITIALIZEitem to restore the various settings of
window.
this unit to their factory default values.
1. Use the §/BROWSE and ¶/MIC buttons to select
INITIALIZE(Execappears light on dark).
2. Press the Ábutton to open a confirmation pop-up
3. Press the Ábutton to execute quick formatting.
window.
Press the
[ª] button to cancel quick formatting.
Using FULL FORMAT
Use the FULL FORMATitem to completely format an SD card.
Using the FULL FORMATitem deletes all music files on the
card, and automatically creates MUSIC and UTILITY folders and
a dr-1.sys file.
3. Press the Ábutton to initialize the settings.
Press the
[ª] button to cancel initialization.
If you use the FULL FORMATitem, the unit checks the
memory for errors before formatting the card. For this reason
it takes a long time compared to the QUICK FORMAToption.
Using QUICK FORMAT
Use the QUICK FORMATitem to format an SD card quickly.
1. Use the §/BROWSE and ¶/MIC buttons to select FULL
Using the QUICK FORMATitem deletes all music files on the
card, and automatically creates MUSIC and UTILITY folders and
a dr-1.sys file.
FORMAT(Execappears light on dark).
1. Use the §/BROWSE and ¶/MIC buttons to select the
QUICK FORMATitem (Execappears light on dark).
84 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
15–System settings
2. Press the Ábutton to open a confirmation pop-up
window.
Use the §/BROWSE and ¶/MIC buttons to select each item,
(when selected, the “:”becomes an “∑”and the setting value
is highlighted or the cursor is shown.
3. Press the Ábutton to execute full formatting.
You can make the following settings for the items on the
screen.
Press the
[ª] button to cancel full formatting.
CAUTION
File name format
When formatting a card, use a TASCAM PS-P520 AC adapter
(sold separately), USB bus power or confirm that the batteries
are sufficiently charged. If the power fails during formatting,
the formatting might not occur correctly.
Use the VALUE (+/–) buttons to set the TYPEitem to WORDor
DATE
.
Options: WORD( default value), DATE
WORD: The six characters set in the WORDitem are used to
name files.
Setting the file name format
Example: LR0000_0000.wav
DATE: The date is used to name files (yymmdd).
Example: 090101_0000.wav
You can set the format of the names given to files recorded by
the unit.
1. Press the MENU button to open the MENUscreen.
NOTE
2. Use the §/BROWSE and ¶/MIC buttons to select the
FILE NAMEmenu item, and press the Ábutton or ¯
button to open the FILE NAMEscreen.
The date is set according to the unit’s internal clock. (See
“Setting the date and time”on page 45.)
TASCAM LR-10 85
Download from Www.Somanuals.com. All Manuals Search And Download.
15–System settings
Setting the characters in the WORD item
When the WORDitem is selected, use the Âand ¯
buttons to move the cursor, and use the VALUE(+/–) buttons
to change each character.
NOTE
In addition to the alphabet and numbers, the following
characters can be used: ! # $ % & ’( ) + , - . ; = @ [ ] ^ _ ` { } ~
The default name prefix is “LR0000”.
86 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
16–Using the footswitch
This unit has a REMOTE jack to which you can connect
a TASCAM RC-3F footswitch-type remote control (sold
separately) that can be used to operate the unit.
4. Use the VALUE (+/–) buttons to change the MODEitem.
FOOT SW
MODE
L
C
R
PLAY
TRAINER
REW
FLASH
PLAY/STOP
PLAY/STOP SPEED CHANGE
FWD
Setting footswitch operation
RECORD OVERDUB REC/PAUSE
MINUTES REW PLAY
STOP
FWD
Use the FOOT SWsetting screen to make footswitch settings.
5. After completing the setting, press the HOME button to
return to the Home Screen.
1. Press the MENU button to open the MENUscreen.
2. Use the §/BROWSE and ¶/MIC buttons to select the
FOOT SWmenu item, and press the Ábutton or ¯
button to open the FOOT SWscreen.
Using the footswitch
Press a pedal on the footswitch to operate the unit. The
function of each pedal corresponds to the assignment shown
on the FOOT SWscreen.
3. The MODEitem and the three footswitch pedal
assignments are shown.
TASCAM LR-10 87
Download from Www.Somanuals.com. All Manuals Search And Download.
17–Viewing File Information
Use the INFORMATIONScreen to view various types of
information about the unit.
File information page
To open the INFORMATIONscreen, press the MENU button
to open the MENUscreen, select the INFORMATIONitem and
press the Á button or ¯button.
The INFORMATIONscreen has the following three pages.
Use the VALUE (+/–) buttons to switch between the pages.
The FILEpage shows information about the currently playing
file.
File information page (FILE
)
•
•
•
Shows information about the currently playing file.
Card information page (CARD
Shows the use status of the currently inserted SD card.
System information page (SYSTEM
WAV or MP3
Shows the audio file format.
)
For WAV files, bit length, stereo/mono and sampling
frequency (Hz) are shown.
)
Shows information about the unit’s system settings and
firmware version.
For MP3 files, bit rate (kbps), CBR (constant bit rate) or VBR
(variable bit rate) type and sampling frequency (Hz) are
shown.
When you are done, press the HOME button to return to the
Home Screen, or press the MENU button to open the MENU
screen.
TITLE
Shows the file name.
If an MP3 file has ID3 tag title information that information
appears instead.
DATE
Shows the date and time that the file was created.
88 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
17–Viewing File Information
SIZE
NOTE
Use the ¯button to switch between display of REMAIN
Shows the file size.
SIZEand USEDSIZE
.
Card information page
The CARD page shows the use status of the currently inserted
SD card.
TOTAL MUSIC
Shows the number of playable files in the MUSIC Folder.
TOTAL FOLDER
Shows the number of folders in the MUSIC Folder.
TOTAL SIZE
Shows the total SD card memory capacity.
REMAIN SIZE
Shows the amount of unused memory on the SD card.
USED SIZE
Shows the amount of used memory on the SD card.
TASCAM LR-10 89
Download from Www.Somanuals.com. All Manuals Search And Download.
17–Viewing File Information
System information page
The SYSTEMpage shows information about the unit’s system
settings and firmware version.
CUE/REV SPD
Shows the speed of forward and backward searching.
AUTO OFF
Shows the automatic power OFF setting.
BATTERY
This shows the battery setting.
System Ver.
Shows the system firmware version.
90 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
18–Messages
The following is a list of the popup messages that might appear on the LR-10 under certain conditions. Refer to this list if one of
these popup messages appears and you want to check the meaning or determine a proper response.
Message
Meaning and response
The DIVIDE function would cause the file name to exceed 200 characters. The DIVIDE function adds "_a”or “_b
to the end of the file name. Before choosing the DIVIDE function, connect the unit to a computer and edit the
file name to less than 198 characters.
”
File Name ERR
The DIVIDE function would cause the file name to be the same as that of an existing file. The DIVIDE function
adds "_a”or “_b”to the end of the file name. Before choosing the DIVIDE function, connect the unit to a com-
puter and edit the file name.
Dup File Name
The file added to the playlist cannot be found or a file could be damaged. Please check the file in question.
File Not Found
Non-Supported
The audio file is not a supported format. Please see "11-Transferring songs to and from a computer" for file
formats that this unit can use.
The battery is almost out of power. Replace the AA batteries.
Battery Empty
I/O Too Short
The IN (starting) and OUT (ending) points are too close together. Reset the IN (starting) and OUT (ending)
points with at least 1 second between them.
The file in the Playlist cannot be found. Please confirm that the file is still in the Music Folder.
File Not Found
PLAYLIST
No files have been added to the Playlist. Add a file to the Playlist or change the play mode to something be-
No PLAYLIST
sides PLAYLIST
.
The playlist is full. You cannot add more than 99 tracks to the Playlist.
PLAYLIST Full
The card is not formatted properly or the formatting is broken. Change the card or press the Á button when
this message appears to format the card in FAT format.
CAUTION: Execution of FAT formatting erases all data currently on the card.
MBR Error Init
CARD
TASCAM LR-10 91
Download from Www.Somanuals.com. All Manuals Search And Download.
18–Messages
Message
Meaning and response
The FAT formatting of the card is abnormal or broken. This message also appears if you FAT formatted the card
using a computer connected by USB and if a new card is inserted in the unit. Always use the LR-10 to conduct
FAT formatting of cards to be used with it. Change the card or press the Á button when this message appears
Format Error
Format CARD
to format the card in FAT format.
CAUTION: Execution of FAT formatting erases all data currently on the card.
The system file is missing. This unit requires a system file for operation. When this message appears, press Á
button to automatically create a system file.
File Not Found
Make Sys File
The system file required to operate this unit is invalid. When this message appears, press Á button to auto-
matically create a system file.
Invalid Sys File
Make Sys File
Something might be wrong with the card. Change the card.
Invalid Card
Change Card
This appears when the card is protected and lacks the necessary Music Folder and other folders and files. Un-
lock the write protect switch, restart the power and format the card.
Protected Card
Change Card
Writing to the card timed out.
Write Timeout
Backup files on the card to your computer, and format the card.
The card has no remaining capacity. Erase unnecessary files or move them to your computer to make open
space.
Card Full
Folders can be created down to two layers. You cannot create a new folder inside the current folder.
The position selected for divide is not suitable (too close to the beginning or end of a track).
The file is larger than the designated size or the recording time exceeded 24 hours.
The total number of folders and files exceeds 5000. Erase unnecessary files or move them to your computer.
The card could not be handled properly. Replace the card.
Layer too Deep
Can't Divide
Max File Size
File Full
Card Error
MP3 files cannot be divided.
Current File MP3
92 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
18–Messages
Message
File Protected
No Card
Meaning and response
The file is read only and cannot be erased.
No card is in the unit, so recording is not possible.
There is no file that can be played back. The file might be damaged.
There is no playback file, so DIVIDE and OVERDUB cannot be executed.
No PB File
No MUSIC File
Not Continued
File Error
Can't Save Data
Player Error
Device Error
Writing Failed
Sys Rom Err
If any of these errors occur, turn the unit power OFF and restart it. If the power cannot be turned OFF, remove
the batteries and disconnect the AC adaptor (if connected). If the error message continues to appear, please
contact a TEAC Repair Center.
Remote Cmd
Remote Rx
System Err 50
System Error 1
System Error 2
System Error 3
System Error 4
TASCAM LR-10 93
Download from Www.Somanuals.com. All Manuals Search And Download.
18–Messages
Message
Meaning and response
System Error 5
System Error 6
System Error 7
System Error 8
System Error 9
If any of these errors occur, turn the unit power OFF and restart it. If the power cannot be turned OFF, remove
the batteries and disconnect the AC adaptor (if connected). If the error message continues to appear, please
contact a TEAC Repair Center.
94 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
19–Troubleshooting
If you are having trouble with the operation of this unit,
please try the following before seeking repair. If these
measures do not solve the problem, please contact the store
where you bought the unit or a TASCAM Service Center.
ª Playback does not work.
If you are trying to play a WAV file, confirm that the
sampling frequency is supported by this unit.
•
If you are trying to play an MP3 file, confirm that the bit
rate is supported by this unit.
•
ª Power will not turn ON.
Confirm that the batteries are not dead.
•
•
ª No sound is output.
Confirm that the batteries are installed with the correct +/–
orientation.
Are headphones connected?
•
•
•
•
Check the connections with the monitoring system.
Is the volume of the monitoring system minimized?
Is the OUTPUT setting of the unit minimized?
Confirm that the power plug of the AC adaptor (TASCAM
PS-P520: sold separately) is securely inserted.
•
ª The foot switch does not function.
ª Recording does not work.
Confirm that a battery is installed in the foot switch and
that it is not dead.
•
If you are using an external device, check the connection
again.
•
ª The unit does not function.
Check the input settings again.
•
•
•
Is the unit connected to a computer by USB (USB
connected) ?.
•
Confirm that the recording level is not too low.
Has MIC/LINE input been disabled (MIC or LINE icon (
ª The SD card is not recognized.
or
)not shown light on dark)?
Confirm that the SD card is inserted completely.
•
Confirm that the SD card is not full.
•
•
Confirm that the number of files has not reached the
maximum that the unit can handle.
TASCAM LR-10 95
Download from Www.Somanuals.com. All Manuals Search And Download.
19–Troubleshooting
ª The recording level is low.
ª This unit’s files do not appear on the computer.
Confirm that the input level setting is not too low.
Confirm that the unit is connected to the computer using
its USB port.
•
•
•
•
Confirm that the GAINsetting is not too low.
Are you using a USB hub?
•
•
Confirm that the output level of a connected external
device is not too low.
Confirm that the unit is not recording or in recording
standby mode.
ª The sound I am trying to record sounds distorted.
Is the INPUT LEVELsetting low and the input gain setting
high?
•
ª The playback sounds unnatural.
Confirm that the playback pitch is not being adjusted.
•
•
Confirm that the playback speed is not being adjusted.
ª I cannot erase a file.
Is the SD card write-protect switch engaged?
•
96 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
20–Specifications
Maximum input level : +6 dBV (2.0 V) , (INPUT volume at 7)
Ratings
Minimum input level : –22 dBV (0.08 V) , (INPUT volume at 10)
Recording media
Built-in microphone
SD card (64 MB - 2 GB)
Omni directional, Stereo
SDHC card (4 GB - 32 GB)
Recording format
WAV: 44.1kHz, 16-bit
Output ratings
Playback format
WAV: 44.1 kHz, 16/24-bit
Analog output ratings
/LINE OUT
MP3: 44.1/48 kHz, 32/64/96/128/192/256/320 kbps
Connector
: 1/8”(3.5 mm) stereo mini
: 23Ω
Number of input channels
Output impedance
2 channels (stereo)
Nominal output level : –14 dBV (10 kΩ load)
Maximum output level : +2 dBV (10 kΩ load)
Input ratings
Maximum output
: 15 mW + 15 mW (32Ω load)
Built-in speaker
0.4 W (monaural)
Analog audio input
LINE IN jack
Connector
Control input/output ratings
USB jack
Connector : Mini-B type
: 1/8”(3.5 mm) stereo
: 23 kΩ
Input impedance
Nominal input level : –10 dBV (0.32V) , (INPUT volume at 7)
Format
: USB 2.0 HIGH SPEED, mass storage class
TASCAM LR-10 97
Download from Www.Somanuals.com. All Manuals Search And Download.
20–Specifications
REMOTE jack
64 MB or more memory
Connector : 2.5mm TRS
USB port (USB 2.0 recommended)
Recommended USB host controller
Intel chipset
Audio performance
Supported OS
Windows : Windows XP , Windows Vista , Windows 7
Frequency response
20 Hz - 20 kHz +1/–3 dB
Macintosh : Mac OS X 10.2 or later
(LINE IN to LINE OUT , Fs=44.1 kHz)
Total harmonic distortion
0.03% (LINE IN to LINE OUT, Fs=44.1 kHz)
Other specifications
S/N ratio
Power
90 dB (LINE IN to LINE OUT, Fs=44.1 kHz)
Two AA batteries (Alkaline or Ni-MH)
AC adaptor (TASCAM PS-P520, sold separately)
USB bus power
Computer compatibility
Power consumption
0.4 W (during MP3 playback)
Windows
Pentium 300 MHz or faster
Battery operation time (continuous operation)
Alkaline type battery ( EVOLTA )
128 MB or more memory
USB port (USB 2.0 recommended)
About 13 hours (WAV, recording time when using the built-
in microphones input)
Macintosh
Power PC, iMac, G3, G4 266 MHz or faster
98 TASCAM LR-10
Download from Www.Somanuals.com. All Manuals Search And Download.
20–Specifications
Dimensional drawings
About 13 hours (WAV, MP3, music playback time when
using headphones)
About 8 hours (WAV, MP3, music playback time when using
the built-in speaker)
Ni-MH type battery ( eneloop )
About 11 hours (WAV, recording time when using the built-
in microphones input)
30 mm
158 mm
About 11 hours (WAV, MP3, music playback time when
using headphones)
About 7.5 hours (WAV, MP3, music playback time when
using the built-in speaker)
Dimensions (W x H x D)
158 x 30 x 70 mm
6.220 x 1.181 x 2.756 in.
• Illustrations and other depictions may differ in part from
the actual product.
Weight
• Specifications and external appearance may be changed
without notification to improve the product.
170 g /5.996 oz (not including batteries)
Operating temperature range
0 - 40°C/32°F - 104°F
TASCAM LR-10 99
Download from Www.Somanuals.com. All Manuals Search And Download.
LR-10
TEAC CORPORATION
Phone: +81-42-356-9143
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
7733 Telegraph Road, Montebello, California 90640 USA
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. de C.V.
Phone: +52-55-5010-6000
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México
TEAC UK LIMITED
Phone: +44-8451-302511
Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|