D01092420A
BB-1000CD
Portable CD/SD Recorder
BB-800
Portable SD Recorder
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
Do not expose this apparatus to drips or splashes.
•
•
Do not place any objects filled with liquids, such
as vases, on the apparatus.
Do not install this apparatus in a confined space
such as a book case or similar unit.
•
•
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
The apparatus draws nominal non-operating
power from the AC outlet with its POWER or
STANDBY/ON switch not in the ON position.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
The apparatus should be located close enough
to the AC outlet so that you can easily grasp the
power cord plug at any time.
•
•
•
•
8 Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
The main plug is used as the disconnect device,
the disconnect device shall remain readily
operable.
9 Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong. The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
If the product uses batteries (including a battery
pack or installed batteries), they should not be
exposed to sunshine, fire or excessive heat.
CAUTION for products that use replaceable lithium
batteries: there is danger of explosion if a battery
is replaced with an incorrect type of battery.
Replace only with the same or equivalent type.
Caution should be taken when using earphones or
headphones with the product because excessive
sound pressure (volume) from earphones or head-
phones can cause hearing loss.
•
10 Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by
the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
TASCAM BB-1000CD/BB-800
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY PRECAUTIONS
CAUTIONS ABOUT LASER RADIATION
CAUTIONS ABOUT BATTERIES
ª
ª
This product has been designed and manufactured
according to FDA regulations “title 21, CFR, chapter
1, subchapter J, based on the Radiation Control for
Health and Safety Act of 1968”, and is classified as
a class 1 laser product. There is no hazardous invis-
ible laser radiation during operation because invisible
laser radiation emitted inside of this product is com-
pletely confined in the protective housings.
This product uses batteries. Misuse of batteries could
cause a leak, rupture or other trouble. Always abide
by the following precautions when using batteries.
Never recharge non-rechargeable batteries. The
•
batteries could rupture or leak, causing fire or inju-
ry.
When installing batteries, pay attention to the
polarity indications (plus/minus (+/–) orientation),
and install them correctly in the battery compart-
ment as indicated. Putting them in backward could
make the batteries rupture or leak, causing fire,
injury or stains around them.
•
The label required in this regulation is shown at
.
1
When throwing used batteries away, follow the
disposal instructions indicated on the batter-
ies and the local disposal laws. When you store
or dispose batteries, isorate their terminals with
insulation tape or something like that to prevent them
from contacting other batteries or metalic objects.
•
•
Do not use batteries other than those specified.
Do not mix and use new and old batteries or differ-
ent types of batteries together. The batteries could
rupture or leak, causing fire, injury or stains around
them.
Do not carry or store batteries together with small
metal objects. The batteries could short, causing
leak, rupture or other trouble.
•
•
•
Do not heat or disassemble batteries. Do not put
them in fire or water. Batteries could rupture or
leak, causing fire, injury or stains around them.
CAUTION
If the battery fluid leaks, wipe away any fluid on
the battery case before inserting new batteries. If
the battery fluid gets in an eye, it could cause loss
of eyesight. If fluid does enter an eye, wash it out
thoroughly with clean water without rubbing the
eye and then consult a doctor immediately. If the
fluid gets on a person’s body or clothing, it could
cause skin injuries or burns. If this should happen,
wash it off with clean water and then consult a
doctor immediately.
• DO NOT REMOVE THE PROTECTIVE HOUSING
USING A SCREWDRIVER.
• USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
• IF THIS PRODUCT DEVELOPS TROUBLE,
CONTACTYOURNEARESTQUALIFIEDSERVICE
PERSONNEL, AND DO NOT USE THE PRODUCT
IN ITS DAMAGED STATE.
The unit power should be off when you install and
replace batteries.
•
•
• CLASS 1M INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS DEFEATED.
DO NOT VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS.
Remove the batteries if you do not plan to use the
unit for a long time. Batteries could rupture or
leak, causing fire, injury or stains around them. If
the battery fluid leaks, wipe away any fluid on the
battery compartment before inserting new batter-
ies.
Optical pickup
Type
: HOP-6201TC
• Small children may mistakenly swallow a lithium
coin battery and it is very dangerous. Keep the
battery and the remote control out of the reach of
small children. In the event a battery is swallowed,
immediately consult a physician.
Manufacturer
Laser output
Wavelength
: Hitachi Media Electronics Co,Ltd.
: Lessthan75mWontheobjectivelens(record)
: 777 to 787 nm
TASCAM BB-1000CD/BB-800
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
TASCAM BB-1000CD/BB-800
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1 – Introduction
Thank you very much for purchasing the TASCAM
BB-1000CD/BB-800 Portable CD/SD Recorder. Please read
this Owner’s Manual carefully in order to maximize your
use of all the unit’s features. We hope that you will enjoy
using this recorder for many years to come. After you have
finished reading this manual, keep it in a safe place.
selection keys, as well as a CD eject key. In addition to
recording to CDs, the BB-1000CD can also copy files
between CDs and SD cards, including allowing the dupli-
cation of CDs for backup.
Included items
The items included with the product are listed below.
Take care when opening the package to avoid damaging the
items. Keep the packaging materials for transportation in
the future.
Please contact the store where you purchased this unit if
any of these items are missing or have been damaged dur-
ing transportation.
Main features
Portable CD/SD recorder (BB-1000CD)
•
•
•
•
Portable SD recorder (BB-800)
Built-in speakers and microphones
Recording directly to an SD (SDHC) card possible (WAV
or MP3 format)
• Main unit........................................................................ 1
• PS-1225LAC adaptor ..................................................... 1
• RC-BB1000 Wireless remote control............................. 1
• Coin battery (CR2025) for remote................................. 1
• Warranty card................................................................. 1
• Owner's manual (this document) ................................... 1
Long duration recording possible (MP3 format)
•
•
Recording directly to a CD-R/RW (CD-DA format)
possible (BB-1000CD only)
Easy operation with knobs and keys
•
•
Changing playback speed without changing pitch
possible
Changing playback pitch without changing speed
possible
Note about this manual
This manual uses the following conventions.
•
Instrument tuner functions
Metronome functions
•
•
•
•
“SD memory cards” are called “SD cards.”
•
•
Keys and connectors on the unit and external devices and
messages on the display are written like this: MENU.
5 W + 5 W digital amplifier
The CD-DA format is also called the "audio CD" format.
In addition, a disc on which tracks are recorded in the
audio CD format is called an "audio CD."
Two pairs of stereo microphones on the front and back
allow 360-degree recording
•
•
Mix and record input sounds with playback
(overdubbing)
•
•
•
Additional information is introduced as needed in the
following categories.
Copying from audio CDs to SD cards (WAV or MP3
format) possible (BB-1000CD only)
TIP
Copying files from SD cards to audio CDs possible
(BB-1000CD only)
This is a useful hint about ways to use the unit.
Duplicating audio CDs possible (BB-1000CD only)
Power with included AC adaptor or 8 AA batteries
Remote control unit (RC-BB1000) included
NOTE
•
•
•
•
A note explains actions in special situations and supple-
mental information.
2 XLR mic input jacks can provide 48V phantom power
for condenser microphones
CAUTION
These instructions should be followed to avoid injury,
damage to the unit or other equipment, or loss of
recording data.
Stereo pair of RCA line input jacks for connecting
external devices
•
•
•
Stereo pair of RCA line output jacks for connecting
external devices
Intellectual property rights
TASCAM is a registered trademark of TEAC
Sound from connected external microphones can be
output through speakers
•
Corporation.
Differences between BB-1000CD and
BB-800 models
The BB-1000CD has all the features of the BB-800 and
adds CD recording functions. In order to utilize these
features, the BB-1000CD has additional CD and SD
SDHC Logo is a trademark.
•
•
Supply of this product does not convey a license nor
imply any right to distribute MPEG Layer-3 compliant
content created with this product in revenue-generating
TASCAM BB-1000CD/BB-800
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1 – Introduction
broadcast systems (terrestrial, satellite, cable and/or
other distribution channels), streaming applications (via
Internet, intranets and/or other networks), other content
distribution systems (pay-audio or audio-on-demand
applications and the like) or on physical media (compact
discs, digital versatile discs, semiconductor chips, hard
drives, memory cards and the like). An independent
license for such use is required. For details, please visit
Extremely cold places
Places with bad ventilation or high humidity
•
•
Humming noises could occur when using the unit near
a power amplifier or other device that has a large trans-
former. Increase the distance between the devices and
change their orientations if humming occurs.
•
Using the unit near a TV or radio may cause picture
deterioration or noise. Increase the distance from such
devices
•
•
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
•
•
Using wireless equipment, such as cellular phones,
near the unit may cause noise, especially when calls are
incoming and outgoing and being made with a phone.
Increase the distance from such devices or turn them off.
Other company names, product names and logos in this
document are the trademarks or registered trademarks of
their respective owners.
Do not use the unit upside down or lying on its side.
Doing so could cause CD recording and playback to
malfunction. Place it with its operation panel up.
•
Any data, including, but not limited to information,
described herein are intended only as illustrations of
such data and/or information and not as the specifica-
tions for such data and/or information. TEAC CORPO-
RATION disclaims any warranty that any use of such
data and/or information shall be free from infringement
of any third party’s intellectual property rights or other
proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement,
or arising from or connected with or related to the use of
such data and/or information.
Beware of condensation
Condensation could occur if the unit is moved from a cold
to a warm place or used after a sudden temperature change.
If this occurs, let the unit sit for one or two hours at the new
room temperature before using it.
Cleaning the unit
To clean the unit, wipe it gently with a soft dry cloth. Do not
use benzene, paint thinner, ethyl alcohol or other chemical
agents to clean the unit as they could damage the surface or
cause fading.
This product is designed to help you record and
reproduce sound works to which you own the copyright,
or where you have obtained permission from the
copyright holder or the rightful licensor. Unless you
own the copyright, or have obtained the appropriate
permission from the copyright holder or the rightful
licensor, your unauthorized recording, reproduction
or distribution thereof may result in severe criminal
penalties under copyright laws and international
copyright treaties. If you are uncertain about your rights,
contact your legal advisor. Under no circumstances will
TEAC Corporation be responsible for the consequences
of any illegal copying performed using the recorder.
About SD cards
This unit uses SD cards for recording and playback. You
can use 64 MB – 2 GB SD cards and 4 GB – 32 GB SDHC
cards with this unit. A list of SD cards that have been tested
with this unit can be found on the TASCAM web site (www.
tascam.com).
Precautions for use
SD cards are delicate media. In order to avoid damaging
a card or the card slot, please take the following precau-
tions when handling them.
•
Cautions on installation
Do not leave them in extremely hot or cold places.
Do not leave them in extremely humid places.
Do not let them get wet.
•
•
•
•
•
The unit’s nominal operating temperature is between 5˚
and 35° C (41° – 95° F).
•
Do not install in the following types of places. Doing
so could degrade the sound quality and/or cause
malfunctions.
•
Do not put things on top of them or twist them.
Do not strike them.
Places with significant vibrations or that are other-
wise unstable
Near windows or other places exposed to direct
sunlight
•
•
•
About Compact Discs
The built-in CD drive in BB-1000CD units can record and
play audio in the CD-DA format on CD-R and CD-RW
discs.
Near heaters or other extremely hot places
TASCAM BB-1000CD/BB-800
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1 – Introduction
Copy-protected discs and other discs which do not
conform to the CD standard may not play back correctly
in this player. If you use such discs in this unit, TEAC
Corporation and its subsidiaries cannot be respon-
sible for any consequences or guarantee the quality of
reproduction. If you experience problems with such
non-standard discs, you should contact the producers of
the disc.
•
Precaution for CD use
Use only CD, CD-R and CD-RW discs that bear the
following logos.
•
CD-R
About CD-R and CD-RW discs
CD-RW
CD-R discs can be recorded only once, and recorded tracks
cannot be erased. However, if the disc has not been finalized
and sufficient space is available on the disc, additional
material can be recorded. After finishing recording, final-
izing a CD-R makes it playable in most ordinary CD players
(some CD players might not be able to play these discs).
In contrast, if a CD-RW disc becomes full, tracks on it can
be erased, and the space on the disc can be reused for new
recordings. However, only the last recorded track or all
recorded tracks can be deleted. Selectively deleting tracks
recorded earlier is not possible. Even after being finalized,
CD-RW discs can only be played in players that specifically
support their playback.
Always insert the disc into the slot with the label side
toward you.
•
•
To remove a disc from its storage case, press down on
the center of the case and lift the disc out, holding it
carefully by the edges.
Avoid touching the signal recording side (the side
without the label). Fingerprints and oil on the disc,
for example, could cause errors during recording and
playback.
•
•
Inserting a disc into the slot-loading
drive
Should fingerprints or dust get on the signal recording
side, wipe the surface from the center hole outward
towards the outer edge with a soft, dry cloth. Discs
should always be cleaned before storage to remove grime
that could cause reduced sound quality.
Never clean discs with record sprays, antistatic sprays
or fluids, benzene, thinner or other chemicals. Such
chemicals can do irreparable damage to the disc’s plastic
surface and make playback impossible.
•
•
1 Insert the disc partway into the slot by holding
the disc by the edge with the label side forward as
illustrated.
Do not affix any labels or stickers to the label side of a
disc. Do not insert discs that have adhesive remaining
from tape or stickers that have been removed. Doing
so could cause the disc to become stuck in the unit or
otherwise make it malfunction.
2 Push the disc further until the disc is almost com-
pletely hidden and it will be automatically pulled into
the slot.
If a disc does not loaded properly
Never use a stabilizer. Using a commercially-available
CD stabilizer with this unit could prevent playback or
cause malfunction.
•
If a disc does not load properly, pull out the disc and press
the EJECT (ø) key, and then try to load it again. (Do not
force the disc in, because this could damage the unit and the
disc.)
Do not use cracked discs.
•
•
Do not use CDs with irregular shapes, including
octagonal, heart-shaped and business card-sized CDs,
because they could cause the unit to malfunction.
TASCAM BB-1000CD/BB-800
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2 – Part Names and Functions
Top panel
BB-1000CD
ª
BB-800
ª
3 VOLUME knob
1 FRONT MIC/EXT MIC knob and overload indicator
Use this knob to adjust the input level of the front
built-in microphones (FRONT MIC) or external micro-
phones (EXT MIC). The indicator on the upper left lights
when the input level is too high.
Use this knob to adjust the speaker volume and the
output level of headphones and line out signals.
4 Display
This shows variety information.
2 REAR MIC/LINE knob knob and overload indicator
Use this knob to adjust the input level of the rear built-in
microphones (REAR MIC) or the signal from the LINE
IN jacks.
5 ENTER key
Use this key to confirm selections when using a settings
screen.
6 DATA wheel
The indicator on the upper left lights when the input
level is too high.
When a setting screen is open, use the wheel to select
items and change setting values.
TASCAM BB-1000CD/BB-800
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 – Part Names and Functions
o HOME key
When the Home screen is open, use the wheel to adjust
the playback position in a song.
When one of the setting screens is open, press this key
to return to the Home screen.
7 METRONOME key
p MENU key
This opens the METRONOME screen.
When the METRONOME screen is open, press this
key to return to the Home screen. (See “Using the
metronome” on page 36.)
When the Home screen is open, press this key to open
the menu list (MENU screen).
When a setting screen is open, press this key to return to
the MENU screen.
8 SPEED knob
a F2 Key
Use this to adjust the playback speed. (See “Practicing
with a CD or SD card” on page 37.)
The function of this key depends on the current
operation. The current function is shown on the bottom
right of the display and could be confirmation of a
selection or moving to the next step.
9 KEY knob
Use this to adjust the pitch of playback in semitones.
(See “Practicing with a CD or SD card” on page 36.)
s CURSOR [§/¶/˙/¥] keys
0 FINE PITCH knob
Use these keys to move the cursor (highlighted area) on
setting screens.
Use this to adjust the pitch of playback in cents. (See
“Practicing with a CD or SD card” on page 36.)
d STOP key
q ø EJECT key (BB-1000CD only)
Press this key to stop playback and return to the
beginning of the stopped track.
Press this to eject a CD.
w CD key and indicator (BB-1000CD only)
When the Home screen is open, press this key to change
the recording/playback media to CD.
f Â/Ô key
Press this key within 1 second from the beginning of a
track to skip to the beginning of the previous track.
Press it more than 1 second after the beginning of a
track to skip to the beginning of the current track.
Press and hold this key to search backward.
Press this key during loop playback to move the
end point of the loop to the current start point, while
maintaining the length of the loop.
The indicator lights when CD is selected.
e SD key and indicator (BB-1000CD only)
When the Home screen is open, press this key to change
the recording/playback media to SD card.
The indicator lights when SD card is selected.
r INPUT key
Press this to open the INPUT screen.
When the INPUT screen is open, press this key to return
to the Home screen.
g ¯/ key
Press this key to skip to the next track.
Press and hold this key to search forward.
Press this key during loop playback to move the start
point of the loop forward to the current end point, while
maintaining the length of the loop.
t BALANCE key
Press this to open the BALANCE screen where you can
adjust the input balance.
When the BALANCE screen is open, press this key to
return to the Home screen.
h PLAY/READY [Á/π] key
When the Home screen is open and playback is stopped,
press this key to start playback.
y OVERDUB key [ ]
º
During playback, press this key to pause it at the current
point in the track.
Press this key when playing a track on a CD or an SD
card to record the playback track mixed with input
signals.
j FLASH BACK key
Press this key to put the unit into overdub recording
standby. The OVERDUB key lights and the REC/READY
key flashes.
Press this key to skip a few seconds back in a track
during playback. You can adjust the flash back time on
the SETUP screen. (See “Going back a few seconds
(FLASH BACK)” on page 46.)
u REC/READY [ ] key
º
Press this when the unit is stopped to put the unit into
recording standby. The key flashes when in standby.
Press this when in recording standby to start recording.
This key lights during recording.
k TUNER key
Press this to open the TUNER screen, which can be used
to help tune instruments. (See “Tuning instruments” on
page 35.)
Press this during recording to put the unit into recording
standby again.
When the TUNER screen is open, press this key to
return to the Home screen.
i F1 key
l LOOP key
The function of this key depends on the current
operation. The current function is shown on the bottom
left of the display and could be confirmation of a
selection or returning to the previous step.
Use this to turn the loop playback and repeat playback
functions on and off.
When start and end points are set, this turns loop
playback on and off. (See “Repeating playback of a set
interval (loop playback)” on page 34.)
TASCAM BB-1000CD/BB-800
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2 – Part Names and Functions
z OUT key
When start and end points are not set, this turns repeat
playback on and off. (See “Repeating playback of a
track” on page 34.)
Use this key to set the end point for loop playback of a
desired interval.
Press the IN/OUT/MARK key while pressing and
holding this key to clear the corresponding start/end/
marker point.
Press this key while pressing and holding the LOOP key
to clear the end point. (See “Repeating playback of a set
interval (loop playback)” on page 34.)
; IN key
x
MARK key
Use this key to set the start point for loop playback of a
desired interval.
Press this key while pressing and holding the LOOP key
to clear the start point. (See “Repeating playback of a
set interval (loop playback)” on page 34.)
Press this to set a marker point at the desired position
in a track. Press this key while pressing and holding the
LOOP key to clear the marker point currently shown
on the Home screen. (See “Setting marker points where
desired in tracks” on page 34.)
Front Panel
c FRONT MIC L/R
When using the chromatic tuner function, the LEDs
indicate the difference between the detected and desired
pitches.
This is a built-in stereo pair of microphones.
The left microphone is also used when tuning.
v Power indicator
n Remote sensor
This indicator lights when the power is ON.
This receives signals from the included remote control
unit (RC-BB1000). Point the tip of the remote control at
the sensor when operating the unit with it.
b Volume/playback/recording indicator
When adjusting the volume, the number of green LEDs
lit shows the volume.
The center LED lights green during playback.
The center LED lights red during recording.
When using the metronome function, the green light
moves left to right along with the tempo.
TASCAM BB-1000CD/BB-800
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2 – Part Names and Functions
Rear Panel
Inside of the battery
compartment
m REAR MIC L/R
, Battery compartment
This is a built-in stereo pair of microphones.
The compartment holds 8 AA batteries.
Left side panel
@ PHONES jack
Use this to connect headphones.
# DC IN 12V jack
Connect the included AC adaptor (TASCAM PS-1225L)
here.
$ Power cord holder
This holds the power cord to prevent unexpected discon-
nection of the cord.
% AUTO/LIMITER
Use this to activate and deactivate the automatic gain
control and limiter functions.
^ LINE IN jacks
Connect the line out jacks of an electronic instrument,
CD player or other external audio device.
& PHANTOM switch
Turn this on to supply phantom power (+48 V) to
condenser mics connected to the EXT MIC jacks.
CAUTION
Do not connect or disconnect microphones when the
PHANTOM switch is ON.
* EXT MIC A (L)/EXT MIC B (R) jacks
Connect microphones to these XLR jacks. (1: GND 2:
HOT 3: COLD)
. POWER switch
Use this switch to turn the power on and off.
/ LINE OUT jacks
Use these to connect electronic instruments with built-in
speakers, powered speakers and other audio equipment.
! SPEAKER switch
Use this switch to turn the built-in speakers ON and
OFF.
TASCAM BB-1000CD/BB-800
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2 – Part Names and Functions
( SD card slot
Right side panel
Insert SD cards into this slot.
) Force disc ejection hole (BB-1000CD only)
Use this to eject a disc if the CD drive malfunctions and
does not eject the disc
BB-1000CD
ª
(See “Forcing disc ejection” on page 19.)
Q CD slot (BB-1000CD only)
Insert CDs into this slot
Remote control unit (RC-BB1000)
Ô
Â
STOP
˚
¯
1
4
5
PLAY/READY
¥/π
ª
RECORD
º
2
3
＋
VOLUME
ー
6
‰
RC-BB1000
BB-800
ª
1 Ô/Â key
Press this key within 1 second from the beginning of a
track to skip to the beginning of the previous track.
Press it more than 1 second after the beginning of a
track to skip to the beginning of the current track.
Press and hold this key to search backward.
Press this key during loop playback to move the
end point of the loop to the current start point, while
maintaining the length of the loop.
2 STOP [ª] key
Press this key to stop playback and return to the
beginning of a stopped track.
3 RECORD [º] key
Press this when the unit is stopped to put the unit into
recording standby.
Press this when in recording standby to start recording.
4 /¯ key
Press this key to skip to the next track.
Press and hold this key to search forward.
Press this key during loop playback to move the start
point of the loop forward to the current end point, while
maintaining the length of the loop.
5 PLAY/READY [Á/π] key
When the Home screen is open and playback is stopped,
press this key to start playback.
During playback, press this key to pause it at that point.
6 VOLUME [+/–] keys
Use these to adjust the volume.
TASCAM BB-1000CD/BB-800
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2 – Part Names and Functions
q Playback position display bar
Home screen
This bar shows the current playback position, darkening
from the left as playback proceeds.
w F1 key function
This shows the function currently assigned to the F1
key. On the Home screen, pressing it skips playback to
the nearest previous marker position.
e Status of loop IN and OUT points
These show the status of the IN and OUT point settings
for loop playback.
If an IN point is set, the icon appears at its location
under the playback position display bar.
If an OUT point is set, the icon appears at its location
under the playback position display bar.
1 Current operation status icon
¥
Track playing
π
File stopped in progress (paused)
File stopped at its beginning
Searching forward
r F2 key function
·
This shows the function currently assigned to the F2
key. On the Home screen, pressing it skips playback to
the next marker position.
˚
∆
≤
µ
Searching backward
Skipping to the beginning of the next track
Skipping to the beginning of the current or
previous track
:
File dividing mode
2 Loop/repeat status icon
The following icons appear depending on the current
loop/repeat setting.
Repeat playback
Loop playback
3 Level meter
During playback, the signal levels of the playing track
are indicated.
The right end of a meter stays lit for a while if the signal
level on that channel becomes too high.
4 File number
The number of the file currently playing is shown.
5 Marker name
The name of the marker nearest to and before the current
playback position is shown.
6 Speaker output status
The speaker output status is shown.
:
:
:
Built-in speakers ON
Built-in speakers OFF
Headphones connected
7 Power status
When batteries are being used, the battery icon shows
the amount of power remaining with bars (
,
,
).
If the icon has no bars ( ), the batteries are almost dead
and the power will soon turn OFF. When using the AC
adaptor,
is shown.
8 Elapsed time
Shows the elapsed time (hours: minutes: seconds) of the
currently playing track.
9 Remaining time
Shows the remaining playback time of the current track
(hours: minutes: seconds).
0 Marker positions
The positions of markers are indicated with
above the playback position display bar.
icons
TASCAM BB-1000CD/BB-800
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3 – Preparation
Installing batteries
Remove the battery compartment cover and install 8
commercially-available AA batteries following the polarity
indications on the case.
Powering the unit
You can power the unit with the included AC adaptor or
commercially-available AA batteries.
CAUTION
You cannot record on a CD when operating on battery
power. Use the AC adaptor.
Connecting the AC adaptor
Connect the AC adaptor to the unit, the power cord to the
AC adaptor, and the power cord to an AC outlet.
TASCAM PS-1225L
DC plug
NOTE
Batteries are not supplied with this product. . We recom-
mended using Ni-MH or alkaline batteries.
Power cord
holder
AC outlet
Preparing the remote control
Installing the battery
1 Pull the battery holder out of the remote control.
The left side panel of the unit has a power cord holder
indentation for fastening the cable of the AC adaptor. Insert
the cord into the holder to prevent accidental disconnection
of the cord.
2 Put a lithium coin battery (CR2025) into the holder
with the + side up.
CAUTION
Do not force the power cord into the holder. Doing
so could damage the cord.
•
3 Put the battery holder into the remote control.
Uninstall the batteries when using the included AC
adaptor to prevent battery consumption.
•
Battery replacement
Replace the battery when the operation range decreases
or the unit does not respond to keys pushed on the remote
control unit.
Use a lithium coin battery (CR2025) for replacement.
TASCAM BB-1000CD/BB-800
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3 – Preparation
based on this setting.
Precautions about using the remote control
Remove the batteries if you do not plan to use the remote
control for a long time (longer than a month).
1 Press the HOME key to open the Home screen.
•
Using this remote control while other equipment that
can be controlled with infrared rays is operating nearby
might cause that equipment to function improperly.
•
2 Press the MENU key to open the MENU screen.
Aim the remote control unit at the remote sensor.
Obstacles could interfere with operation by the remote
control.
•
Remote sensor
3 Use the DATA wheel or CURSOR [§/¶] keys to select
SETUP, and press the ENTER key.
Ô
Â
STOP
˚
¯
The SETUP screen appears.
PLAY/READY
¥/π
4 Use the CURSOR [§/¶] keys to select the DATE/TIME
ª
RECORD
º
item, and press the ENTER key.
Operating distance
Head-on to the sensor: 7 m
15° left/right from the sensor: 4 m
Turning the power on and off
Turning the power ON
Slide the POWER switch on the left side of the unit to ON.
The Home screen opens after the startup screen disappears.
The DATE/TIME screen appears.
5 Use the DATA wheel to adjust the value. Use the
CURSOR [§/¶/˙/¥] keys to move the cursor.
Turning the power OFF
Slide the POWER switch to OFF.
CAUTION
Do not turn the power OFF when a media indicator (CD
or SD) is flashing because the unit is writing data.
6 After making the setting, press the F1 key to to return
to the SETUP screen and start the clock.
Setting the date and time
Set the current date and time of the built-in clock. The time
information of files recorded by this unit to an SD card is
TASCAM BB-1000CD/BB-800
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3 – Preparation
Connecting microphones
Powered speakers
or audio system
To record with external mics or use the unit as an amplifier,
connect microphones to the EXT MIC A (L) and EXT MIC
B (R) jacks (XLR jacks) on the left side panel. Use micro-
phones with XLR connectors.
Microphones
Headphones
Connecting external audio devices to the unit’s
input
Connect the outputs of external audio equipment to the
LINE IN jacks (RCA) on the left side panel using RCA
cables.
CAUTION
Do not connect or disconnect microphones when the
PHANTOM switch is ON.
•
•
Some microphones might be damaged if phantom
power is turned ON when they are connected. Refer
to the microphone manuals and other documentation
for details.
Turn the PHANTOM switch ON after connecting
condenser microphones and other microphones that
require power from the unit.
•
•
Turn the switch OFF when using dynamic microphones
and other types that do not require power.
Audio device or
external sound
source
Connecting external audio devices
Connecting headphones, amplifiers and
powered speakers
You can connect headphones to the PHONES jack (stereo
mini jack) and powered speakers, audio systems and other
monitoring systems to the LINE OUT jacks (RCA) using
commercially-available RCA cables.
Using SD cards
SD card write protection
SD cards have write protection switches that prevent new
data from being written. If you try to record to a protected
card, a “Protected Card” error message appears.
TASCAM BB-1000CD/BB-800
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3 – Preparation
• When formatting, use the AC adaptor or batteries that
have sufficient remaining charge. If the power turns OFF
during formatting, formatting could fail.
1
2
Insert the SD card.
Press the HOME key to open the Home screen.
NOTE
3
Press the SD key (BB-1000CD only). The indicator
above and to the left of the SD key lights.
In addition to during recording, this unit also writes
information to the SD card when editing and setting
marks, for example. When the write protection is
engaged, this information cannot be written. Disengage
the write-protect switch to enable these functions.
Inserting and removing SD cards
4
5
Press the MENU key to open the MENU screen.
Inserting SD cards
ª
Push an SD card in until it clicks fully into place.
Use the DATA wheel or CURSOR [§/¶] keys to select
MEDIA, and press the ENTER key.
Removing SD cards
ª
The MEDIA SD screen opens.
Press the inserted card in slightly to make it eject.
6
Use the DATA wheel or CURSOR [§/¶] keys to select
FORMAT, and press the ENTER key.
NOTE
Do not remove the SD card during recording or
playback, or while the SD indicator is flashing (writing
data).
Formatting an SD card
To use a new SD card or a card that has been formatted for
another device or by a computer, we recommend that you
format the card with this unit. Using an SD card formatted
on another device or a computer could cause recording
errors.
7
The following confirmation screen appears. Press
the F1 key to start formatting. When formatting
completes, the MEDIA SD screen reopens.
CAUTION
• Beware that formatting erases all the data on an SD
card, including data written by other equipment.
TASCAM BB-1000CD/BB-800
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3 – Preparation
Ejecting a disc
Press the EJECT [ø] key. After the disc is ejected halfway,
pull it out by holding its edge.
NOTE
You cannot eject a disc when the unit is turned OFF.
•
•
A disc can only be ejected when the Home screen is
open.
A disc cannot be ejected when an SD card file is being
played.
•
•
USING CDS (BB-1000CD only)
A finalization confirmation message appears before
ejecting a disc that has not yet been finalized. (See
“Finalizing a CD-R/RW so that it can be played in
other CD players (BB-1000CD only)” on page 29.)
Inserting a disc
1
Insert the disc halfway with the label facing forward
as shown in the following illustration.
Forcing disc ejection
If pressing the EJECT [ø] key does not eject the disc
because the CD drive is malfunctioning, for example, you
can force a disc to eject by using the force disc ejection
hole.
To force a disc to eject, turn the unit’s power OFF and
follow the procedures below
1
Prepare a long pin such as a stretched paper clip.
2
Insert the pin into the force disc ejection hole and
push it in several times.
3
Pull the disc out by hand after it is ejected halfway.
CAUTION
Never try to force a disc to eject using the force disc
ejection hole when the unit’s power is ON.
2
Push the disc in further until it is pulled in automat-
ically when almost hidden.
CAUTION
You cannot insert a disc when the unit is turned OFF.
•
•
If a disc sticks, for example becoming difficult to push,
pull out the disc and press the EJECT [ø] key, and then
try to load it again. Do not force the disc in. Doing so
could damage the unit or the disc.
If a disc other than an audio CD is inserted, or a disc
is inserted backwards, it will be automatically ejected
when CD is selected.
•
TASCAM BB-1000CD/BB-800
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
4
Raise the levels of both the FRONT MIC/EXT MIC
and REAR MIC/LINE knobs to record sound in 360°
around the unit.
Selecting whether to record to an SD
card or a CD (BB-1000CD only)
1
Press the STOP key to stop the recorder.
2
3
Press the HOME key to open the Home screen.
NOTE
When using the built-in microphones no sound is output
from the unit’s speakers.
To record to an SD card, press the SD key. The indi-
cator above and to the left of the SD key lights.
Recording with external microphones
To record to a CD, press the CD key. The indicator
above and to the left of the CD key lights.
1
Press the INPUT key to open the INPUT screen.
CAUTION
2
Use the CURSOR [§/¶] keys to select the SOURCE
item.
When operating on battery power, the unit cannot
record to a CD. To record to a CD, use the AC adaptor.
Selecting the input
Recording with built-in microphones
1
Press the INPUT key to open the INPUT screen.
3
Use the DATA wheel to select EXT/REAR or EXT/
LINE.
When EXT/REAR is selected, external microphones and
the unit’s rear microphones can be input and recorded
simultaneously.
When EXT/LINE is selected, external microphones and
external devices connected to the LINE IN jacks can be
used simultaneously.
2
Use the CURSOR [§/¶] keys to select the SOURCE
item.
4
Use the FRONT MIC/EXT MIC knob to adjust the
external microphone input levels.
3
Use the DATA wheel to select FRNT/REAR.
To record signals input through the rear micro-
phones or the line inputs at the same time, use the
REAR MIC/LINE knob to adjust the rear microphone
or line input levels. Turn the REAR MIC/LINE knob
all the way to the left (MIN) to record sound only
from the external microphones.
TASCAM BB-1000CD/BB-800
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
5
Use the CURSOR [§/¶] keys to select the EXT > SP
item.
4
Use the REAR MIC/LINE knob to adjust the line input
recording level.
To record signals input through the front micro-
phones or external microphones at the same time,
use the FRONT MIC/EXT MIC knob to adjust the
front microphone or external microphone record-
ing level. Turn the FRONT MIC/EXT MIC knob all the
way to the left (MIN) to record sounds only from the
line inputs.
6
Set it to ON to output the external microphone
sounds from the speakers. Set it to OFF to disable
the speakers.
TIP
When the speakers are set to output sounds input from
the external microphones, feedback could occur. When
recording with external microphones, we recommend
that you disable the speakers and use headphones to
monitor the input from external microphones.
Setting the recording file format
Recording to an SD card
Recording with line inputs
The four recording file formats that can be selected are MP3
(low), MP3 (normal), MP3 (high) and WAV, with the sound
quality increasing in that order. As sound quality increases,
however, so does file size, reducing the amount of time that
can be recorded. (See the following section for details.)
1
Press the INPUT key to open the INPUT screen.
1
2
3
Press the STOP key to stop the unit.
2
Use the CURSOR [§/¶] keys to select the SOURCE
item.
Press the HOME key to open the Home screen.
Press the MENU key to open the MENU screen.
3
Use the DATA wheel to select FRNT/LINE or EXT/
LINE.
When set to FRNT/LINE, the line inputs and the
unit’s front microphones can be used simultane-
ously.
4
Use the DATA wheel or CURSOR [§/¶] keys to select
REC SETTING, and press the ENTER key.
When set to EXT/LINE, signals from the line inputs
and external microphones can be used simultane-
ously.
TASCAM BB-1000CD/BB-800
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
5
Use the CURSOR [§/¶] keys to select the FILE
TYPE item.
6
Use the DATA wheel to set the file type.
7
Press the HOME key to return to the Home screen.
About recording time
The following tables show the recording times for each recording format and medium capacity.
CD-R/CD-RW (BB-1000CD only)
Recording format
CD/capacity
650MB
700MB
CD-DA 16 Bit, 44.1 kHz
SD/SDHC card
1 hour 14 minutes
1hour 20 minutes
Recording format
SD/SDHC card capacity
4GB
FILE TYPE
(
）
1GB
2GB
8GB
16GB
1 hour 39 minutes
3 hours 18 minutes
6 hours 36 minutes
13 hours 12 minutes
26 hours 24 minutes
WAV 16 Bit 44.1 kHz
,
MP3
Low
35 hours 50 minutes 71 hours 40 minutes 143 hours 20 minutes 286 hours 40 minutes
17 hours 55 minutes 35 hours 50 minutes 71 hours 40 minutes 143 hours 20 minutes
11 hours57 minutes 23 hours 54 minutes 47 hours 48 minutes 95 hours 36 minutes
573 hours 20 minutes
286 hours 40 minutes
191 hours 12 minutes
(44.1 kHz, 64 kbps)
Normal
(44.1 kHz, 128 kbps)
High
(44.1 kHz, 192 kbps)
The recording times in the table above are approximate. Actual recording times could vary depending on the SD/SDHC
card used.
•
TASCAM BB-1000CD/BB-800
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
The recording times in the table above show total
recordable times on SD/SDHC cards, not maximum
continuous recording times.
•
•
•
•
You cannot continuously record for more than 23
hours and 59 minutes. The maximum size of a single
recording file is also 2 GB.
Record a WAV file if you want to divide a file after
recording it to an SD card. The DIVIDE function on
the EDIT screen cannot be used on MP3 files.
When recording to a CD, the sampling frequency
is 44.1 kHz and the quantization bit rate is 16-bit
(BB-1000CD only).
The BROWSE screen opens.
7
Use the DATA wheel or CURSOR [§/¶] keys to move
the cursor to where you want to create a new folder.
Creating new SD card folders
1
Press the STOP key to stop the unit.
2
3
Press the HOME key to open the Home screen.
To create a folder on the first level of the SD card,
select ROOT. To create a folder on the second level,
select the folder that you want the new folder to be
in.
Press the SD key (BB-1000 CD only). The indicator
above and to the left of the SD key lights.
To select a folder on the level above, press the
CURSOR [˙] key. To open the selected folder press
the CURSOR [¥] key.
NOTE
This unit can only make folders on two levels. It can also
only play back files in the first two folder levels.
4
Press the MENU key to open the MENU screen.
8
Press the ENTER key to open a pop-up window.
5
Use the DATA wheel or CURSOR [§/¶] keys to select
MEDIA, and press the ENTER key.
9
Use the DATA wheel or CURSOR [§/¶] keys to select
CREATE, and press the ENTER key.
The MEDIA SD screen opens.
6
Use the DATA wheel or CURSOR [§/¶] keys to select
BROWSE, and press the ENTER key.
TASCAM BB-1000CD/BB-800
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
10 The following screen opens. Press the F1 key to cre-
ate a new folder. Press the F2 key to cancel the oper-
ation.
3
Use the FRONT MIC/EXT MIC knob and the REAR
MIC/LINE knob to adjust the recording levels. Adjust
the levels so that the meters on the display do not
peak at their right ends.
11 Use the DATA wheel or CURSOR [§/¶] keys to select
the newly created folder, and press the ENTER key to
open a pop-up window.
4
5
After setting the levels, press the REC/READY [º]
key to start recording. During recording the REC/
READY [º] key lights.
12 Use the DATA wheel or CURSOR [§/¶] keys to
Press the REC/READY [º] key during recording to
put the unit into recording standby again. The REC/
READY [º] key flashes when the unit is in standby.
choose SELECT, and press the ENTER key.
During recording or when in recording standby,
press the STOP key to stop recording. The REC/
READY [º] key becomes unlit.
NOTE
NOTE
A maximum of 99 tracks can be recorded on a CD.
When folders are created by this unit, folder names
are automatically assigned with incremental suffixes
in a range from “BB_001” to “BB_999”.
•
•
•
A maximum of 99 files can be recorded in each SD
card folder.
The unit can recognize a maximum of 999 total files
and folders.
•
A maximum combined total of 999 files and folders
can be created on one SD card.
•
Each folder can have a maximum of 99 files.
•
•
If a folder is selected and SELECT is chosen on the
BROWSE screen pop-up window, press the enter key
to set that folder for recording and as the playback
area and return to the Home screen. Choose CANCEL
to cancel the operation related to the selected folder.
Recording Screen
Making a recording
1
Press the HOME key to open the Home screen.
Recorder operation
11
This icon shows the current recorder operation.
Recording
ºπ Recording standby
Stopped
2
Press the REC/READY [º] key to put the unit into
recording standby. The REC/READY [º] key flashes.
º
ª
TASCAM BB-1000CD/BB-800
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
Recording level meters
21
2
Use the CURSOR [§/¶] keys to select the MIC L/R
The input signal levels of the selected inputs appear as
separate left (L) and right (R) channels. The right end
of a meter stays lit for a while if the signal level is too
high.
item.
File number
31
The number of the file currently being recorded is
shown.
Elapsed recording time
The elapsed time of the track being recorded opens in
hours: minutes: seconds.
41
3
Use the DATA wheel to adjust the microphone bal-
ance.
The range is L50 – C (center) – R50.
Remaining recording time
51
The remaining time available for recording on the
medium is shown in hours: minutes: seconds.
Current function of the F1 key
61
The current function of the F1 key is shown. On the
Recording screen, pressing this key divides the file
during recording.
NOTE
This setting affects both the built-in microphones and
the external microphones.
•
•
Creating new tracks while continuing to
record
Press the F1 key to restore the balance to the center.
Press the F1 key during recording to create a new track at
that instant and continue recording without pause.
Recording in monaural
You can mix the left and right input signals and record in
monaural (mono).
Turn this function ON when, for example, you are only
using one external microphone.
CAUTION
You cannot divide a track during recording in the
following circumstances.
1
Press the INPUT key to open the INPUT screen.
If the remaining recordable time is four seconds or
less
•
•
•
If only four seconds or less have passed since starting
recording
If only four seconds or less have passed since dividing
the track previously
If 99 tracks have already been recorded to the CD
•
•
2
Use the CURSOR [§/¶] keys to select the MONO
MIX item.
If 99 tracks have already been recorded in the
selected folder on the SD card
When recording to an SD card, if the total number of
files and folders on the SD card is already 999
•
Various recording settings
Adjusting the balance of microphones
3
Use the DATA wheel to set it to ON.
1
Press the BALANCE key to open the BALANCE
screen.
TASCAM BB-1000CD/BB-800
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
4
Press the HOME key to return to the Home screen.
5
Press the HOME key to return to the Home screen.
NOTE
When recording in monaural, the same signal is recorded
to both left and right channels as a stereo file.
Using the automatic recording function
From recording standby, the unit can start and stop
recording automatically in response to input signal levels.
Using the limiter function
1
2
3
Press the STOP key to stop the unit.
During a live performance, for example, loud noises could
be input unexpectedly. By using the limiter function, audio
clipping can be avoided and recordings made without
distortion.
Press the HOME key to open the Home screen.
Press the MENU key to open the MENU screen.
1
Set the AUTO/LIMITER switch on the left side panel
to ON.
2
Press the INPUT key to open the INPUT screen.
4
Use the DATA wheel or CURSOR [§/¶] keys to select
REC SETTING, and press the ENTER key.
3
Use the CURSOR [§/¶] keys to select the LIMITER
item.
4
Use the DATA wheel to choose one of the following
options.
The REC SETTING screen opens.
• LIMITER
The input gain changes automatically according to the
input signal level to prevent distortion caused by exces-
sively loud sounds.
5
Make settings for the following four items. Use the
CURSOR [§/¶] keys to select the items, and use the
DATA wheel to make settings.
• AGC HIGH/AGC LOW
The input gain changes automatically according to the
input signal level to make both loud and quiet sounds
the same level. This is useful when recording people
speaking, such as during meetings.
Select AGC HIGH when the input level is low and AGC
LOW when it is high.
AUTO LEVEL
Set the signal level at which recording starts and stops
automatically. Choose -48 dB, -24 dB, -12 dB or -6 dB.
Lower numbers make recording start at smaller input
volumes. In other words, -48 dB is the most sensitive
setting, which will start recording at the lowest input
volume.
CAUTION
When using AGC, the FRONT MIC/EXT MIC and REAR
MIC/LINE knobs cannot be used to adjust input levels.
TASCAM BB-1000CD/BB-800
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
START
1
2
3
Press the STOP key to stop the unit.
If set to ON, recording automatically starts if the unit is
in recording standby and detects an input signal with a
level higher than that set in the AUTO LEVEL item.
STOP
Press the HOME key to open the Home screen.
Set the time from detecting that the input signal level is
lower than the AUTO LEVEL setting until the unit stops
recording and resumes standby. Choose OFF (default
setting), 5, 10, 15, 20, 25 or 30 seconds.
Press the MENU key to open the MENU screen.
DIV
When set to ON, the recording file is divided when
the input signal level becomes higher than the AUTO
LEVEL setting again after 2 or more seconds below that
setting level.
6
Press the HOME key to return to the Home screen.
4
Use the DATA wheel or CURSOR [§/¶] keys to select
REC SETTING, and press the ENTER key.
When the automatic recording function is ON, the
level set in the AUTO LEVEL item is shown, as in the
following illustrations, on the display meters when in
recording standby (left) or recording (right).
5
Use the CURSOR [§/¶] keys to select FILE TYPE.
TIP
You can automatically skip unnecessary silent moments
during recording by using START and STOP. If you want
to divide recording files at each silence but do not want
to skip silence, activate DIVIDE only. Using the combi-
nation of START, STOP and DIVIDE, you can set the
unit to record while only skipping silences longer than
5 seconds (time set in STOP) or dividing files at each
silence, for example.
6
Use the DATA wheel to select WAV.
Adding performances to an existing
recording (OVERDUB)
While playing back a track from a CD (BB-1000CD only)
or an SD card, you can mix new sounds in and record them
together (overdubbing) on an SD card. For example, you
can record new layers of sound or record playing or singing
along with a karaoke track.
In the following procedures, the playback and perfor-
mance sounds are recorded together by the built-in
microphones.
7
8
Press the HOME key to open the Home screen.
Press the CD or SD key to select the playback medi-
um (BB-1000CD only).
NOTE
An SD card must be inserted in the unit to use the
overdubbing function.
•
•
When the overdubbing function is used to record,
WAV files a created.
TASCAM BB-1000CD/BB-800
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
9
Use the  and ¯ keys to select the track for play-
back.
15 Use the DATA wheel to adjust the unit’s playback vol-
ume. Set the playback volume between 10 and 100,
with 100 being the maximum.
10 Press the PLAY/READY [Á/π] key to start playback.
Perform along with the playback to check and adjust
the volume balance between the playback and live
signals as necessary.
NOTE
Press the F2 key to set the MIX BALANCE to 100. Doing
this, however, could cause the volume to increase
suddenly, so stop playback or turn the output volume
down beforehand.
16 Press the REC/READY [º] key to simultaneously
start recording and playback. The REC/READY [º]
key lights during recording.
11 Set the SPEAKER switch to ON. If any headphones
are connected to the PHONES jack disconnect them.
12 Press the OVERDUB [º] key to start recording
standby. You can also start overdubbing while a
track is playing.
17 During recording, press the REC/READY [º] key
to put the unit into recording standby. The REC/
READY [º] key flashes when in recording standby.
When recording or in recording standby, press the
STOP key to stop recording. The REC/READY [º]
key becomes unlit.
NOTE
When overdubbing, the playback file number is
shown instead of the recording file number and the
recording file number is shown instead of the marker
name on the Recording screen.
•
•
NOTE
When using external microphones, we recommend that
you position them at equal distances from the unit and
the sources of the sounds being input.
Press the PLAY/READY [Á/π] key during recording
standby to start playback without starting recording.
You can also search backward and forward by
pressing and holding the Â/¯ keys.
CAUTION
13 If necessary, adjust the balance by adjusting the vol-
ume of the playback signal. Press the BALANCE key
to open the BALANCE screen.
When using external microphones, do not point the
external microphones toward the speakers. Doing so
could cause feedback.
•
•
Turning up the FRONT MIC/EXT MIC and VOLUME
knobs increases the probability of feedback.
14 Use the CURSOR CURSOR [§/¶] keys to select the
MIX BALANCE item.
TASCAM BB-1000CD/BB-800
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
Overdubbing with higher sound quality
(DIRECT MIX)
In the DIRECT MIX mode, the playback sound and mic
input sounds are mixed in the unit when recording, allowing
overdubbing at higher quality.
Headphones should be used for monitoring to prevent the
microphones from picking up the playback sound.
The DIRECT MIX mode is automatically activated when
headphones are connected. You can also follow the steps
below to activate the DIRECT MIX mode manually to
overdub sounds in higher quality without using headphones
for monitoring. Do this when you overdub the sound of an
electric instrument through the LINE IN jacks, for example.
4
Press the MENU key to open the MENU screen.
5
Use the DATA wheel or CURSOR [§/¶] keys to select
MEDIA, and press the ENTER key.
1
Press the OVERDUB [º] key to start recording
standby.
2
Press the F1 key to activate DIRECT MIX mode.
The MEDIA CD screen opens.
6
Use the CURSOR [§/¶] keys to select FINALIZE,
and press the ENTER key.
After this, follow the same procedures as for ordinary
overdubbing (OVERDUB).
Finalizing a CD-R/RW so that it can be
played in other CD players (BB-1000CD
only)
To play a CD-R/RW disc that was recorded with this unit on
other devices, you must finalize the CD-R/RW disc. Once a
disc has been finalized, new recordings cannot be added to
it unless it is later unfinalized (see below).
The following explanation assumes that CD is selected as
the playback and recording medium and that an unfinalized
CD-R/RW is in the unit.
7
The following confirmation screen opens. Press the
F1 key to start finalizing the disc. When finalization
completes, the MEDIA CD screen reopens.
1
2
Confirm that the unit is stopped.
Press the HOME key to open the Home screen.
3
Press the CD key. The indicator above and to the left
of the CD key lights.
TASCAM BB-1000CD/BB-800
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
NOTE
If you try to eject a CD-R/RW disc that has not yet been
finalized, a finalization confirmation message opens.
Press the F1 key to finalize it, or press the F2 key to eject
it without finalizing.
7
The following confirmation screen opens. Press the
F1 key to start unfinalization. When unfinalization
completes, the MEDIA CD screen reopens.
Preparing a CD-RW so that additional
recordings can be made (BB-1000CD
only)
You can unfinalize a CD-RW that has been finalized to
record additional files.
1
2
Load the CD-RW that you want to unfinalize and
confirm that the unit is stopped.
Deleting tracks from a CD-RW
(BB-1000CD only)
You can erase all the tracks or the last track recorded on a
CD-RW. If the disk has been finalized, you must unfinalize
it first. (See “Preparing a CD-RW so that additional
recordings can be made” above).
Press the HOME key to open the Home screen.
3
Press the CD key. The indicator above and to the left
of the CD key lights.
1
2
Load the CD-RW that you want to delete files from
and confirm that the unit is stopped.
Press the HOME key to open the Home screen.
3
Press the CD key. The indicator above and to the left
of the CD key lights.
4
Press the MENU key to open the MENU screen.
4
Press the MENU key to open the MENU screen.
5
Use the DATA wheel or CURSOR [§/¶] keys to select
MEDIA, and press the ENTER key.
6
The MEDIA CD screen opens. Use the CURSOR
[§/¶] keys to select UNFINALIZE, and press the
ENTER key.
TASCAM BB-1000CD/BB-800
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4 – Recording
5
Use the DATA wheel or CURSOR [§/¶] keys to select
MEDIA, and press the ENTER key.
6
The MEDIA CD screen opens. Use the CURSOR
[§/¶] keys to select ERASE, and press the ENTER
key.
7
Use the DATA wheel to select LAST TRACK (last
track added to the disc) or ALL TRACK (all tracks
on the disc). Press the F1 key to erase the last track
or all tracks. Press the F2 key to cancel the opera-
tion.
TASCAM BB-1000CD/BB-800
31
Download from Www.Somanuals.com. All Manuals Search And Download.
5 – Playback
The audio file formats that this unit can play back from SD
cards are MP3 (32–320 kbps, 44.1 kHz) and WAV (44.1
kHz, 16 bit).
5
Press the MENU key to open the MENU screen.
Discs must be in the audio CD format to be played back on
this unit (BB-1000CD only).
CAUTION
If a disc other than an audio CD is inserted, or a disc
is inserted backwards, it will be automatically ejected
when CD is selected.
6
Use the the DATA wheel or CURSOR [§/¶] keys to
select MEDIA, and press the ENTER key.
Selecting SD card or CD playback
(BB-1000CD only)
1
Confirm that the unit is stopped.
2
Press the HOME key to open the Home screen.
3
Press the SD key to play a file on the SD card. The
indicator above and to the left of the SD key lights.
The MEDIA SD screen opens.
Press the CD key to play a file on the CD. The indi-
cator above and to the left of the CD key lights.
7
Use the DATA wheel or CURSOR [§/¶] keys to select
BROWSE, and press the ENTER key.
Selecting the SD card folder for
playback
Use the BROWSE screen to view folders and audio files on
the SD card, and select the playback folder.
The contents of the folder that contains the currently
selected file are shown.
8
Use the DATA wheel or CURSOR [§/¶] keys to select
a file or folder.
1
2
3
Confirm that the unit is stopped.
Insert an SD card.
Press the HOME key to open the Home screen.
4
Press the SD key (BB-1000CD only). The indicator
above and to the left of the SD key lights.
When a folder is selected, press the CURSOR [¥] key to
show the contents of the folder.
•
•
When a file or folder is selected, press the CURSOR [˙]
key to close the currently opened folder and show the
higher level that contains the folder.
NOTE
Before changing the recording and playback
medium, stop playback or recording. The recording
and playback medium cannot be changed during
•
TASCAM BB-1000CD/BB-800
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5 – Playback
playback or recording, or when the unit is in standby
(BB-1000CD only).
Pausing playback
During playback, press the PLAY/READY [Á/π] key to
pause playback at that point in the track.
When using an SD card, the folder that contains the
currently playing track is the playback area. When
you want to play tracks in another folder, select that
folder from the BROWSE screen.
•
Stopping playback
The unit can recognize a maximum of 999 files and
folders total. Each folder can have a maximum of 99
files.
•
•
During playback, press the STOP key to stop playback and
return to the beginning of the track.
The order that files are shown on the BROWSE screen
is different from the playback order. Open the EDIT
screen to check the playback order. (See “7–Editing
functions and file operations” on page 38.)
Selecting a track
During playback or when the unit is stopped, use the Â
and ¯ keys to select a track.
During playback or when paused in the middle of the track,
press the  key to return to the beginning of the current
track.
Press the  key within 1 second from the beginning of a
track to skip to the beginning of the previous track.
Press the ¯ key to skip to the beginning of the next track.
You can change the playback order using the MOVE
function. (See “7–Editing functions and file opera-
tions” on page 38.)
•
Icons on the BROWSE screen
NOTE
The ª icon appears on the display when playback is
stopped at the beginning of a track, and the π icon
appears when playback is paused in the middle of a
track.
ROOT folder
When the root level is open on the BROWSE screen, the
ROOT folder appears as the top level.
Searching backward and forward
Press and hold the  or ¯ key to search backward or
forward through a track.
Audio file (WAV or MP3 files)
The names of audio files appear after these icons.
Changing playback position with the DATA
wheel
Turn the DATA wheel to adjust the playback position. This
Plus folder
These folders contain subfolders.
movement is reflected in the playback position display bar.
Plain folder
These folders do not contain subfolders.
NOTE
If you turn the DATA wheel during playback, playback
restarts again at the new position when you stop
turning the wheel.
Open folder
The contents of this folder are currently shown on the
screen.
Going back a few seconds (FLASH BACK)
Press the FLASH BACK key during playback or when the
unit is in standby to go back in the track by a preset number
of seconds. The default setting is 2 seconds, but this setting
can be changed to between 1 and 5 seconds using the
FLASH BACK item on the SETUP screen. (See “Operation
settings (SETUP screen settings)” on page 46.)
Playing tracks
Press the HOME key to open the Home screen.
When the unit is stopped, press the PLAY/READY [Á/π]
key to start playback.
TASCAM BB-1000CD/BB-800
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5 – Playback
If only the OUT point is set, the part from the
beginning of the track to the OUT point is played
back repeatedly.
•
•
Repeating playback of a track
You can repeat the playback of a single track (single track
repeat).
When neither the IN point nor the OUT point is set,
the whole track is played back repeatedly.
Press the LOOP key start repeat playback. The
icon
appears on the screen, and the currently playing track plays
repeatedly.
Press the LOOP key again to stop playback.
Setting marker points where desired in
tracks
You can set marker points where desired in tracks and start
playback from these points.
1
During playback or when paused, press the MARK
key at the position you want to mark.
Repeating playback of a set interval
(loop playback)
You can repeat the playback of a selected interval within a
track (loop playback).
2
Press the F1 key to go to the next earlier marker in
the track. Press it again to go back further.
Press the F2 key to go to the next marker in the
track.
1
2
During playback or when paused, press the IN key
to set the point when you want to start loop play-
back. The current position is set as the IN point.
Press the OUT key at the point when you want the
loop to end. The current position is set as the OUT
point, and loop playback begins between the IN and
OUT points.
You can use up to 26 markers (from A to Z) in one track.
•
•
The positions of markers are shown by icons that
appear above the playback position display bar on the
Home screen. In addition, the name of the previous
nearest marker is indicated to the right of the track
number.
Press the
MARK key while pressing and holding the
•
LOOP key to delete the marker that is currently indicated.
The current positions of the IN and OUT points are
shown by the and icons that appear below the
playback position display bar on the Home screen.
•
•
During loop playback, the
indicator also appears.
Press the ¯ key during loop playback to move the start
point of the loop forward to the current end point, while
maintaining the length of the loop.
Press the  key during loop playback to move the
end point of the loop to the current start point, while
maintaining the length of the loop.
Press the IN key or the OUT key while pressing and
holding the LOOP key to clear the start point or the end
point.
•
3
To cancel loop playback, press the LOOP key. The
IN and OUT points remain and loop playback of the
section can be restarted by pressing the LOOP key
again.
NOTE
If only the IN point is set, the part from the IN point
to the end of the track is played back repeatedly.
•
TASCAM BB-1000CD/BB-800
34
Download from Www.Somanuals.com. All Manuals Search And Download.
6 – Practicing with musical instruments
Chromatic tuner mode
Tuning instruments
This unit has a built-in tuner. By using a mic to input the
sound of an instrument, you can use the tuning meter on
the display to tune that instrument accurately. You can also
output tuning pitches.
CAUTION
Playback pauses if you press the TUNER key during
playback of a CD or an SD.
Use the tuning meter on the screen to tune an instrument.
The tuning meter and input signal pitch appear on the
screen. (When no sound is input or the input sound cannot
be measured, "– – –" appears.)
Setting the standard frequency (calibration)
1
Play the instrument to be tuned into the left micro-
phone on the front panel. The nearest pitch name
appears on the screen
1
Press the TUNER key.
2
Tune the instrument until the desired pitch is shown
and the center of the meter lights. A bar appears to
the left if the tuning is too low and a bar appears to
the right if it is too high. The longer the bar is the
more out of tune the instrument is.
The chromatic tuner mode screen opens.
TIP
When tuning you can also check the indicators on the
front panel. The center indicator lights up in green when
in tune with the note. When out of tune, the center
indicator lights up in red and the green indicators to
one side show the degree that the pitch is out of tune.
2
Use the DATA wheel to set the CALIB item (standard
frequency of A) between 435 and 445 Hz.
Oscillator mode
Press the F1 key when in chromatic tuner mode to activate
the unit’s oscillator function and output a standard pitch.
The output page can be set in a three-octave range between
C3 and B5.
The set value also appears in the lower right part of the
screen. This setting affects both tuner modes.
In addition to the CALIB item described above, you can
change the output pitch with NOTE.
Changing the tuning mode
1
Press the TUNER key.
1
Use the CURSOR [§/¶] keys to select the NOTE
2
Press the F1 key to select a tuner mode. Each time
you press F1, the mode changes between chromatic
and oscillator modes.
item.
Set to oscillator mode
Set to chromatic mode
TASCAM BB-1000CD/BB-800
35
Download from Www.Somanuals.com. All Manuals Search And Download.
6 – Practicing with musical instruments
2
Use the DATA wheel to set the accent frequency (time
signature) from 0-9. The accent occurs on the 1.
When set to 0, there is no accent. For example, set it
to 4 for a 4/4 time signature.
2
Use the DATA wheel to select the output pitch
(C3–B5).
Press the F2 key to turn the oscillator sound ON and
OFF.
Starting and stopping the metronome
On the METRONOME screen, press the F1 to start the
metronome and the F2 key to stop it.
Using the metronome
This unit has a built-in metronome function. The volume/
playback/recording indicators on the front panel light in
time with the metronome.
To use the metronome, press the METRONOME key to open
the METRONOME screen.
NOTE
The indicators on the front panel light in time with
the metronome when it is operating
•
•
When using the metronome, you cannot return to
the Home screen. To return to the Home screen, press
the F2 key to stop the metronome and then press the
HOME key.
CAUTION
Playback pauses if you start the metronome during
playback of a CD or an SD.
Changing the speed (TEMPO)
1
Use the CURSOR [§/¶] keys to select the TEMPO
item.
Practicing with CD or SD card playback
You can change the playback tempo of a track without
changing the pitch and change the playback pitch of a track
without changing the tempo.
Furthermore, you can also reduce the sound of a voice
or solo instrument in a track. You can use these special
playback functions to practice and learn parts effectively.
2
Use the DATA wheel to set the tempo in a range
between 20–250 beats per minute.
Changing the playback pitch
Use the KEY and FINE PITCH knobs to change that pitch of
playback without changing the speed.
Use the KEY knob to adjust the pitch up or down by
semitones (â6–#6).
Use the FINE PITCH knob to adjust the pitch by cents
(1/100 of a semitone) in a range of –50 to +50.
Setting the rhythm (BEAT)
1
Use the CURSOR [§/¶] keys to select the BEAT
item.
TASCAM BB-1000CD/BB-800
36
Download from Www.Somanuals.com. All Manuals Search And Download.
6 – Practicing with musical instruments
Changing the playback speed
Use the SPEED knob to adjust the playback speed without
changing the pitch.
The speed adjustment range is –50% to +16% (in 1% incre-
ments), so the slowest speed setting is half the original
speed.
CANCEL (default setting is OFF)
Set to ON to activate the part cancel function.
PART (default setting is C)
Set this to the stereo position of the sound that you want
to reduce. The setting range is L10 (far left) – C (center)
– R10 (far right).
Reducing the sound at a certain stereo position
(PART CANCEL)
Practicing a certain phrase repeatedly
You can select a certain stereo position and reduce the
volume of the sound from that position. For example,
selecting C (center) on commercially-available audio CDs
reduces the vocal sound.
You can continuously repeat the playback of a selected
interval (loop playback). (See “Repeating playback of a set
interval (loop playback)” on page 34.)
Recording while playing along with a CD or SD
card
You can mix and record the playback track with the sounds
input by microphones and the LINE IN jacks. (See “Adding
performances to an existing recording (OVERDUB)” on
page 27).
CAUTION
Depending on the stereo position of the sound and the
use of reverb (echo), the part cancel function might not
be effective or might be less effective than expected.
1
2
Confirm that the unit is stopped.
Press the HOME key to open the Home screen.
3
Press the MENU key to open the MENU screen.
4
Use the DATA wheel or CURSOR [§/¶] keys to select
PART CANCEL, and press the ENTER key.
5
Adjust the following settings as necessary. Use the
CURSOR [§/¶] keys to select items. Use the DATA
wheel to make settings.
TASCAM BB-1000CD/BB-800
37
Download from Www.Somanuals.com. All Manuals Search And Download.
7 – Editing functions and file operations
From the EDIT screen, you can edit files on an SD card.
The following procedures assume that an SD card is
inserted and that it has been selected as the recording and
playback medium. The files shown on the EDIT screen are
the files in the currently selected folder. Select the folder
that contains the file that you want to edit beforehand using
the BROWSE screen.
5
Use the DATA wheel or the CURSOR [§/¶] keys to
select EDIT, and press the ENTER key.
NOTE
These editing functions and other file and folder
operations cannot be used with CDs.
•
•
When the unit is playing or in standby, press the
ENTER key to open the EDIT screen directly. The
playing or paused file becomes the file subject to
editing.
6
The contents of the folder that contains the currently
selected file are shown.
Use the CURSOR [§/¶] keys to select the file that
you want to divide, and press the ENTER key.
If you select PLAY from the pop-up window on the
EDIT screen, the Home screen opens and that file
begins to play. If you select CANCEL, no operation is
conducted on the selected file.
•
•
If you select PLAY from the pop-up window on the
BROWSE screen when a file is selected, the Home
screen opens and that file begins to play. If you select
CANCEL, no operation is conducted on the selected
file.
Dividing files (DIVIDE)
You can divide files that have been recorded in WAV
format.
The following pop-up window opens.
NOTE
MP3 files cannot be divided.
1
2
Confirm that the unit is stopped.
Press the HOME key to open the Home screen.
7
Use the DATA wheel or the CURSOR [§/¶] keys to
select DIVIDE, and press the ENTER key.
3
Press the SD key (BB-1000CD only). The indicator
above and to the left of the SD key lights.
8
The Home screen reopens and playback starts. The
4
Press the MENU key to open the MENU screen.
operation status icon shown is
.
TASCAM BB-1000CD/BB-800
38
Download from Www.Somanuals.com. All Manuals Search And Download.
7 – Editing functions and file operations
9
Press the ENTER key at the point where you want to
5
Use the DATA wheel or the CURSOR [§/¶] keys to
divide the file.
select EDIT, and press the ENTER key.
The following confirmation screen opens, and the track
plays back for two seconds from the point when you
pressed the ENTER key.
10 Press the F1 key to divide the file. Press the F2 key
6
The folder that contains the currently selected file
opens. Use the CURSOR [§/¶] keys to select the file
that you want to move, and press the ENTER key.
to cancel the operation.
NOTE
If you press the ENTER key when the unit is playing or in
standby, the playing or paused file remains selected. If
you select DIVIDE, a confirmation screen opens and the
track plays for two seconds from the point when you
pressed the ENTER key when the track was playing or
paused
If you want to stop dividing a file, select NO by
pressing the F2 key, then press the MENU key. The
EDIT screen reopens.
The following pop-up window opens.
Changing the order of track playback
(MOVE)
1
Confirm that the unit is stopped.
7
Use the DATA wheel or the CURSOR [§/¶]] keys to
2
Press the HOME key to open the Home screen.
select MOVE, and press the ENTER key.
3
Press the SD key (BB-1000CD only). The indicator
above and to the left of the SD key lights.
8
Use the DATA wheel or the CURSOR [§/¶] keys to
move the selected file.
4
Press the MENU key to open the MENU screen.
TASCAM BB-1000CD/BB-800
39
Download from Www.Somanuals.com. All Manuals Search And Download.
7 – Editing functions and file operations
9
Press the ENTER key when the file is at the desired
6
Use the CURSOR [§/¶] keys to select the file that
position.
you want to delete, and press the ENTER key.
Deleting unneeded files (DELETE)
1
Confirm that the unit is stopped.
The following pop-up window opens.
2
Press the HOME key to open the Home screen.
3
Press the SD key (BB-1000CD only). The indicator
above and to the left of the SD key lights.
7
Use the DATA wheel or the CURSOR [§/¶] keys to
select DELETE, and press the ENTER key.
4
Press the MENU key to open the MENU screen.
8
The FILE DELETE confirmation message opens.
Press the F1 key to delete the file, or press the F2 key
to cancel the operation.
5
Use the DATA wheel or the CURSOR [§/¶] keys to
select EDIT, and press the ENTER key.
You can also delete unwanted files from the BROWSE
screen.
1
2
Confirm that the unit is stopped.
Press the HOME key to open the Home screen.
The contents of the folder that contains the currently
selected file are shown.
3
Press the SD key (BB-1000CD only). The indicator
above and to the left of the SD key lights.
TASCAM BB-1000CD/BB-800
40
Download from Www.Somanuals.com. All Manuals Search And Download.
7 – Editing functions and file operations
4
Press the MENU key to open the MENU.
8
Use the DATA wheel or the CURSOR [§/¶] keys to
select DELETE, and press the ENTER key.
5
Use the DATA wheel or the CURSOR [§/¶] keys to
select MEDIA, and press the ENTER key.
9
The FILE DELETE confirmation message opens.
Press the F1 key delete the file, or press the F2 key to
cancel the operation.
6
Use the DATA wheel or the CURSOR [§/¶] keys to
select BROWSE, and press the ENTER key.
The contents of the folder that contains the currently
selected file are shown.
Press the CURSOR [¥] key when a folder is selected to
open that folder and show its contents.
•
•
Press the CURSOR [˙] key when a file or folder is
selected to close the currently open folder and show the
contents of the next higher level.
7
Use the DATA wheel or CURSOR [§/¶] keys, to select
the audio file that you want to delete, and press the
ENTER key. The following pop-up window opens.
TASCAM BB-1000CD/BB-800
41
Download from Www.Somanuals.com. All Manuals Search And Download.
8 – Other useful functions
CAUTION
Outputting external microphone signals
from the speakers
You can connect external microphones to this unit and use it
as an amplifier.
When EXT > SP is set to ON, do not point external
microphones toward the speakers. Doing so could
cause feedback.
•
•
Turning up the FRONT MIC/EXT MIC and VOLUME
knobs increases the probability of feedback. Please
use care when adjusting these.
1
Press the INPUT key to open the INPUT screen.
Copying CD tracks to an SD card
(BB-1000CD only)
You can copy tracks from a CD to an SD card. The tracks
from the CD are copied to the currently open folder on the
SD card. To change the destination folder select the folder
on the BROWSE screen in advance.
2
Use the CURSOR [§/¶] keys to select the SOURCE
item.
1
2
Confirm that the unit is stopped.
Press the HOME key to open the Home screen.
3
Press the MENU key to open the MENU screen.
3
Use the DATA wheel to select EXT/REAR or EXT/
LINE.
4
Use the DATA wheel or CURSOR [§/¶] keys to select
COPY, and press the ENTER key.
4
Use the CURSOR [§/¶] keys to select the EXT > SP
item.
5
Use the DATA wheel or CURSOR [§/¶] keys to select
CD > SD, and press the ENTER key.
5
Use the DATA wheel to set it to ON, allowing the
sounds input from the external microphones to be
output through the speakers.
NOTE
This function is for outputting the sound input by
external microphones. Sound input from the built-in
microphones cannot be output through the speakers.
•
•
When using only one microphone, set MONO MIX to
ON to output the sound through both the left and
right speakers.
TASCAM BB-1000CD/BB-800
42
Download from Www.Somanuals.com. All Manuals Search And Download.
8 – Other useful functions
6
Use the DATA wheel to set the format for the files
saved on the SD card, and press the F2 key.
Creating a CD from files on an SD card
(BB-1000CD only)
You can make an audio CD from files on an SD card.
Choose tracks to be copied to the CD from those contained
in the SD card folder that is currently being used. Select
the folder that contains the files that you want to put on the
audio CD beforehand using the BROWSE screen.
NOTE
MP3 files can be copied to a CD, but they will automati-
cally be converted into WAV format to create an audio
CD.
NOTE
1
2
Confirm that the unit is stopped.
The four recording file formats that can be selected are
MP3 (low), MP3 (normal), MP3 (high) and WAV, with
the sound quality increasing in that order. As sound
quality increases, however, so does file size, reducing the
amount of time that can be recorded.
Press the HOME key to open the Home screen.
3
Press the MENU key to open the MENU screen.
7
Use the DATA wheel or CURSOR [§/¶] keys to select
a track that you want to copy to the SD card, and
press the ENTER key. A check mark appears next to
the selected track.
4
Use the DATA wheel or CURSOR [§/¶] keys to select
COPY, and press the ENTER key.
NOTE
If you choose an already checked track, you can remove
the check mark by pressing the ENTER key.
8
Repeat the previous step to mark other files to be
copied to the card, and press the F2 key. A confirma-
tion screen opens.
5
Use the DATA wheel or CURSOR [§/¶] keys to select
SD > CD, and press the ENTER key.
9
Press the F2 key again to start copying the tracks.
When complete, the COPY screen reopens.
The TRACK LIST screen opens, showing the files in the
selected folder on the SD card.
To cancel the operation, press the F1 key to reopen the
COPY screen without copying any files.
6
Use the DATA wheel or CURSOR [§/¶] keys to select
a file that you want to put on the CD-R/RW disc,
and press the ENTER key. A check mark appears
next to the selected track.
TASCAM BB-1000CD/BB-800
43
Download from Www.Somanuals.com. All Manuals Search And Download.
8 – Other useful functions
11 Insert a blank CD-R/RW, and press the F2 key to
start writing the selected files to the CD-R/RW.
After the disc has been written completely if you
want to make another copy of the same CD, follow
the instructions on the screen, and insert a blank
disc and press the F2 key.
Press the F1 key to end the operation and reopen the
COPY screen.
NOTE
If you choose an already checked track, you can remove
the check mark by pressing the ENTER key.
Backing up an audio CD (BB-1000CD
only)
You can use an SD card to make a backup copy of an audio
CD.
7
Repeat the previous step to mark all the other files
to be put on the CD, and press the F2 key.
1
2
Confirm that the unit is stopped.
The TRACK ORDER screen opens.
Press the HOME key to open the Home screen.
8
You can change the order of the tracks if desired.
Use the DATA wheel or CURSOR [§/¶] keys to select
the file that you want to move, and press the ENTER
key.
3
Press the MENU key to open the MENU screen.
4
Use the DATA wheel or CURSOR [§/¶] keys to select
COPY, and press the ENTER key.
9
Use the DATA wheel or CURSOR [§/¶] key to change
the order, and press the ENTER key.
5
Use the DATA wheel or CURSOR [§/¶] keys to select
CD BACKUP, and press the ENTER key.
10 Repeat the previous two steps as necessary to put the
tracks in the order that you want them on the CD,
and press the F2 key. The following confirmation
screen opens.
6
Insert an SD card and the CD that you want to
backup, and press the F2 key to start making a tem-
porary copy on the SD card.
TASCAM BB-1000CD/BB-800
44
Download from Www.Somanuals.com. All Manuals Search And Download.
8 – Other useful functions
NOTE
The following warning appears if the SD card does not
have enough open capacity.
7
Insert an SD card that has enough capacity, and
press the F2 key to start making the backup.
When the contents of the CD have been completely backed
up on the SD card, the CD is automatically ejected. A
message asking you to insert a new CD-R/RW disc appears.
8
Insert a blank CD-R/RW, and press the F2 key to
start creation of a backup on the CD-R/RW. After
the backup is completed, the disc is automatically
ejected.
If you want to make another backup of the same
disc, insert a new CD-R/RW, and press the F2 key.
Press the F1 key to end the operation and reopen the
COPY screen.
TASCAM BB-1000CD/BB-800
45
Download from Www.Somanuals.com. All Manuals Search And Download.
9 – Operation settings (SETUP screen settings)
Make settings according to your use needs on the SETUP
screen.
Set date and time (DATE/TIME)
Use this item to set the unit’s internal clock. (See “Setting
1
2
Confirm that the unit is stopped.
the date and time” on page 46.)
Press the HOME key to open the Home screen.
3
Press the MENU key to open the MENU screen.
4
Use the CURSOR [§/¶] keys to select SETUP, and
press the ENTER key.
5
Settings for the items below can be made on the
SETUP screen. Use the CURSOR [§/¶] keys to select
an item, and use the DATA wheel to change its set-
tings.
Set automatic backlight OFF time (BACKLIGHT)
Use this item to set how long after the last operation until
the backlight turns off when operating on battery power.
Select OFF (backlight always on), 5 sec (default setting), 10
sec, 15 sec, or 30 sec.
Adjust display contrast (CONTRAST)
Use this to adjust the display contrast.
Set the value between 1 and 20 (default setting: 8).
Set flash back time (FLASH BACK)
Use this to set the number of seconds that the flashback
function goes back in a track.
Set the value from 1–5 sec (default setting: 2 sec).
TASCAM BB-1000CD/BB-800
46
Download from Www.Somanuals.com. All Manuals Search And Download.
10 – Messages
The table below is a list of pop-up messages. Under certain circumstances, the unit may show one of these messages. Please
check this table if you want to know the meaning and how you should respond.
Message
Meaning and response
File not found
The audio file cannot be found or is corrupted. Check the audio file that caused this message.
The audio file is not a supported format. Check the file format.
Non-Supported
The battery is almost out of power. Turn off the power and replace the batteries or supply power using
the dedicated TASCAM PS-1225L AC adaptor.
Battery Empty
I/O Too Short
Write Timeout
When trying to start loop playback using the IN or OUT key, the IN and OUT points are too close
together. Reset the IN and OUT points and try again.
Writing to the SD card timed out. Backup files on the card to your computer, and format the card using
the unit. (See “Formatting an SD card” on page 18.)
The SD card does not have any more open space. Erase unnecessary files or move them to your
computer to make open space.
Media Full
Max File Size
File Full
The size of a file exceeds 2 GB or recording has continued for 24 hours or more.
The total number of files in a folder is already 99 or the combined total number of folders and files on
the SD card is already 999. Erase unnecessary files or move them to your computer
No Card
No SD card was found when trying to record to an SD card. Insert a recordable SD card and try again.
The SD card that you tried to record on or write other data to is protected. Eject the SD card, disengage
its protect switch and insert it again.
Protected Card
This appears if you try to record when the battery power is low. Replace the batteries or supply power
using the dedicated TASCAM PS-1225L AC adapter.
Battery Low
No CD
When you tried to record, no CD was loaded. Insert a recordable CD-R/CD-RW and try again.
When you tried to record, the inserted CD was not an audio CD. Insert a recordable CD-R/CD-RW and
try again.
Not Audio CD
When you tried to record, the inserted CD was a finalized disc. If the disc is a finalized CD-RW,
unfinalize it to make recording on it possible. (See “Preparing a CD-RW so that additional recordings
can be made (BB-1000CD only)” on page 30) and try again. Otherwise, replace the inserted disc with a
recordable CD-R/CD-RW.
CD is CLOSED
You tried to overdub a recording, but the recording format was set to MP3. Set the FILE TYPE under
the REC SETTING menu to "WAV." (See “Setting the recording file format” on page 21.)
Format is MP3
No PB File
You tried to overdub a recording, but no playback track was found. If the playback media is set to CD,
insert an audio CD that is not blank and try again. If the playback media is an SD card, add an audio file
that can be played back to it and try again.
Layer too Deep
File Protected
You cannot make a folder at the current level. Make it at the level above.
This appears when trying to delete or divide a read-only file. You cannot delete or divide such a file
with the unit.
Recording to an SD card is stopped because the unit tried to make a new recording file automatically,
but 99 recording files have already been made.
File Num Full
When copying files from an SD card to a disc, if the total time of the selected files is more than 74
minutes, this message appears. Use a disc with 80-minute capacity or deselect some files.
Over 74 minutes
When copying files from an SD card to a disc, if the total time of the selected files is more than 80
minutes, this message appears. You cannot copy all the selected files even on an 80-minute disc.
Deselect some files.
Over 80 minutes
Over track
More than 99 tracks have been selected on the screen for selecting tracks to copy. You cannot select
more tracks. Deselect some tracks.
Execution of some operations are not possible under the following circumstances:
You cannot ERASE a disc other than an audio CD-RW.
You cannot FINALIZE a disc other than an audio CD-R/RW.
You cannot UNFINALIZE a disc other than an audio CD-RW.
•
•
•
Cannot Execute
TASCAM BB-1000CD/BB-800
47
Download from Www.Somanuals.com. All Manuals Search And Download.
10 – Messages
Messages
Meaning and response
Finalized Disc
Not Finalized
You tried to execute FINALIZE with a disc that is already finalized. You do not need to finalize it.
You tried to execute UNFINALIZE with an unfinalized disc. You do not need to unfinalize it.
The unit failed to execute a FINALIZE, UNFINALIZE or ERASE operation for some reason. Check
for scratches or dirt on the media.
Execute Failed
Cannot DIVIDE
less than 2sec
You selected DIVIDE for a WAV file that is less than 2 seconds long, but you cannot divide a file that is
2 seconds or less.
The SD card is not formatted properly or the formatting is broken. When “Are you Sure?” appears,
press the ENTER key to format the entire SD card in FAT format. All data on the file is erased during
formatting.
MBR Error
Init CARD
Format Error
Format CARD
The FAT formatting of the SD card is abnormal or broken.
Invalid Card
Change Card
This appears when an SD card error occurs when the unit is turned on.
There was some sort of error with the SD card. Turn the power off once and replace the card with a
working card.
Card Error
Disc Error
The unit failed when writing data on a disc. Check scratches or dirt on the disc.
CD Drive Error
Not Continued
File Error
Player Error
Device Error
Writing Failed
Sys Rom Err
System Err 50
System Err 1
System Err 2
System Err 3
System Err 4
System Err 5
System Err 6
System Err 7
System Err 8
System Err 9
If any of these errors occur, turn the unit's power off once and restart the unit. Disconnect the AC
adaptor and remove the batteries if you cannot turn the power off. If the error message continues to
appear, contact a TASCAM Service Center
TASCAM BB-1000CD/BB-800
48
Download from Www.Somanuals.com. All Manuals Search And Download.
11 – Troubleshooting
If the unit does not function properly, please review the
following troubleshooting tips before requesting service.
If you are still unable to resolve the problem, contact the
store where you purchased the unit or a TASCAM Service
Center.
No power
ª
Is the power plug fully connected to the power outlet?
•
Are the batteries installed with the proper +/–
orientation?
•
Remote control does not work.
ª
Is a battery in the remote control and does it have suffi-
cient charge?
•
No sound
ª
Are headphones plugged in?
Is the SPEAKER switch OFF?
Is the monitoring system properly connected?
Is the VOLUME knob set to MIN?
•
•
•
•
Sound is distorted when recording
ª
Are the FRONT MIC/EXT MIC or REAR MIC/LINE
knobs on the top panel turned up too high?
•
Are the levels of the input signals too high?
•
I hear noise
ª
Are the cables connected and working properly?
•
A CD does not play
ª
Is the disc scratched or dirty?
•
Input levels cannot be adjusted with their
knobs.
ª
Is the automatic gain control (AGC) function on?
•
A CD recorded on this unit cannot be
played on other CD players.
ª
Has the CD been finalized?
•
The playback sounds strange.
Is the part cancel function on?
ª
•
•
•
Have you adjusted the playback pitch?
Have you adjusted the playback speed?
TASCAM BB-1000CD/BB-800
49
Download from Www.Somanuals.com. All Manuals Search And Download.
12 – Specifications
Ratings
Audio performance
Frequency response
Recording media
ª
20-20 kHz (±1 dB)
SD card (64 MB - 2 GB), and SDHC card (4 GB - 32 GB)
CD-R, CD-RW, CD-R-DA, CD-RW-DA (high speed
CD-RW is supported) (BB-1000CD only)
Distortion (THD+N)
0.05% (1 kHz LPF 20 kHz)
Signal to noise ratio
Playback media
ª
85 dB (1 kHz, LPF 20 kHz A-Weighted)
SD card (64 MB - 2 GB), and SDHC card (4 GB - 32 GB)
CD-DA, CD-R, CD-RW, CD-R-DA, CD-RW-DA (high
speed CD-RW is supported) (BB-1000CD only)
General
Recording/Playback format
ª
Power: AC adaptor or 8 AA batteries
ª
WAV (when SD/SDHC card is used)
Sampling frequency: 44.1 kHz
Quantization bit rate: 16 bit
MP3 (when SD/SDHC card is used)
Sampling frequency: 44.1 kHz
Bit rate: 64 kbps, 128 kbps, 192 kbps
AC adapter
AC adaptor input: AC100 - 240V, 50 - 60 Hz
AC adaptor output: 12V DC
AC adaptor output current: 2.5 A
Battery life (Continuous operation):
ª
About 1.5 hours (JEITA CD playback, Speaker output
mode, BB-1000CD only)
Audio input and output ratings
About 2.5 hours (JEITA SD record/playback, Speaker
output mode)
About 4.5 hours (SD record/playback, headphone output
mode)
LINE INPUT (L/R) [UNBALANCED]
ª
Connector: RCA pin jack
Nominal input level: -10 dBV
Maximum input level: +6 dBV
Minimum input level: –22 dBV
Input impedance: 20 kΩ
Power consumption:
ª
30 W (when playing back SD, Line In: +6 dBV input,
Maximum speaker output)
EXT MIC A/B (L/R) [BALANCED]
ª
Dimensions (W x H x D):
380 x 204.7 x 107 mm/14.96 x 8.06 x 4.21 in.
Weight:
Connector: XLR-3-32 (1: GND 2: HOT 3: COLD)
Nominal input level: –13 dBu
Maximum input level: +3 dBu
Minimum input level: –55 dBu
Input impedance: 2.4 kΩ
ª
ª
BB-1000CD: 3.4 kg/7.50 lb
BB-800: 3.2 kg/7.06 lb
Build-in microphone
ª
Controllable range of the remote control:
ª
Front: Omnidirectional L/R
Rear: Omnidirectional L/R
Head-on to the sensor: 7 m
15° left/right from the sensor: 4 m
LINE OUTPUT (L/R) [UNBALANCED]
ª
Operating temperature:
ª
Connector: RCA pin jack
5 to 35°C
Nominal output level: –10 dBV
Maximum output level: +6 dBV
Output impedance: 200Ω
PHONES
ª
Connector: Stereo mini jack (3.5 mm dia.)
Output: more than 30 mW + 30 mW
(THD+N less than 1.0%, 32Ω load)
SPEAKERS
ª
3 inch x 2
AMPLIFIERS
ª
5 W + 5 W
TASCAM BB-1000CD/BB-800
50
Download from Www.Somanuals.com. All Manuals Search And Download.
12 – Specifications
Dimensional drawings
107 mm
380 mm
Illustrations may differ slightly from production models.
•
•
Design and specifications are subject to change without notice.
TASCAM BB-1000CD/BB-800
51
Download from Www.Somanuals.com. All Manuals Search And Download.
BB-1000CD
BB-800
TEAC CORPORATION
Phone: +81-42-356-9143
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
7733 Telegraph Road, Montebello, California 90640 U.S.A.
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. de C.V.
Phone: +52-55-5010-6000
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México
TEAC UK LIMITED
Phone: +44-8451-302511
Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|
