TL-PA2030
AV200 3-port Mini Powerline Adapter
REV1.0.0
1910010848
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
Safety Information
•
When product has power button, the power button is one of the way to shut off the product; when
there is no power button, the only way to completely shut off power is to disconnect the product or
the power adapter from the power source.
•
•
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and
voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
II
Download from Www.Somanuals.com. All Manuals Search And Download.
This product can be used in the following countries:
AT
ES
LT
BG
FI
BY
FR
MT
SK
CA
GB
NL
TR
CZ
GR
NO
UA
DE
HU
PL
DK
IE
EE
IT
LV
SE
PT
RO
RU
III
Download from Www.Somanuals.com. All Manuals Search And Download.
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: AV200 3-port Mini Powerline Adapter
Model No.: TL-PA2030
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical regulations
applicable to the product within the scope of Council Directives:
Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents：
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 50412-2-1:2005
EN60950-1:2006+A11:2009+A1:2010+A12:2011
The product carries the CE Mark
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2013
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan
Rd, Nanshan, Shenzhen, China
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Package Contents ............................................................................................................ 1
Chapter 1 Introduction..................................................................................................... 2
1.1 Conventions ............................................................................................................................ 2
1.2 System Requirement............................................................................................................... 2
1.3 Important Safety Instructions................................................................................................... 2
Chapter 2 Connecting Mechanism.................................................................................. 4
2.1 Introduction ............................................................................................................................. 4
2.2 LED Indicator .......................................................................................................................... 4
2.3 Physical Interface.................................................................................................................... 5
2.4 Connection Instruction............................................................................................................. 6
2.5 Hardware Connection – Computer..........................................................................................6
2.6 Hardware Connection – Internet .............................................................................................7
Chapter 3 Installing Management Utility......................................................................... 8
Chapter 4 Using the Management Utility...................................................................... 12
4.1 Status .................................................................................................................................... 12
4.1.1 Set Local Device’s Network Name..................................................................................13
4.2 Network ................................................................................................................................. 14
4.2.1 Rename the Remote Device/Enter Password ................................................................15
4.2.2 Add Device...................................................................................................................... 15
4.3 System .................................................................................................................................. 16
4.3.1 Upgrade Firmware.......................................................................................................... 16
4.3.2 Reset Device .................................................................................................................. 17
4.3.3 Set All Devices’ Network Name ......................................................................................18
5.1 Pair (Secure with 128 bits-AES)............................................................................................19
5.2 Set Up a Powerline AV Network with the Pair Button............................................................19
Appendix A: Troubleshooting........................................................................................ 21
V
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Package Contents
The AV200 3-port Mini Powerline Adapter package contains the following items:
¾
One AV200 3-port Mini Powerline Adapter (There are two AV200 3-port Mini Powerline Adapters in
Starter Kit)
¾
¾
One RJ45 Ethernet Cable (There are two RJ45 Ethernet Cables in Starter Kit)
One Resource CD
z
z
This Guide
Management Utility
Note:
)
Make sure that the package contains the above items. If any of the above items are damaged or missing,
please contact your dealer immediately.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Chapter 1 Introduction
Congratulations on your purchase of this outstanding Powerline Adapter. This device is an AV200 3-port
Mini Powerline Adapter which transforms your house’s existing electrical wiring into a ubiquitous
networking infrastructure. Simply plug this AV200 3-port Mini Powerline Adapter into an ordinary AC
power outlet which will easily extend your Cable/xDSL broadband connection or existing Ethernet (LAN)
network to any other electrical outlet in any room of a house without the need of any new cabling.
This Powerline Adapter supports up to 200Mbps data rate over the existing household power circuit.
With data rates of 200Mbps, full multimedia application can easily be supported throughout the whole
house in addition to Internet access. This Powerline Adapter uses the existing power lines installed in a
home as a path to transmit digital data, voice, audio and video between devices.
To ensure data communication’s security and multimedia applications, this Powerline Adapter supports
built-in 128-bit AES encryption. With minimum setup, you can install and use this Powerline Adapter
within minutes. The adapter adds two useful functions.
1．Existing connection with a new unassociated device added via the Pair button.
2．Reset to default setting via the Management Utility.
1.1 Conventions
The powerline adapter or AV200 3-port Mini Powerline Adapter mentioned in this guide stands for TL-PA2030
AV200 3-port Mini Powerline Adapter without any explanation.
1.2 System Requirement
a) At least two power outlets (100–240V~) with standard home power wiring
b) A computer with the following:
¾ Operating System with TCP/IP installed
¾ Pentium III compatible processor and above
¾ Ethernet LAN card installed with TCP/IP protocol
¾ 64 MB RAM or more
¾ 50 MB of free disk space (Minimum)
¾ CD-ROM Drive
1.3 Important Safety Instructions
1. Do not open this product or attempt to service it; it may expose you to dangerous high voltage or
other risks.
2. Do not operate this product near water.
3. Do not place or operate this product near a radiator or a heat register.
4. Do not expose this product to dampness, dust or corrosive liquids.
5. Do not connect this product or disconnect it from a wall socket during a lightning or a thunderstorm
6. Do not block the ventilation slots of this product, for insufficient airflow may harm it.
7. Do not put anything on this product.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
8. Plug this product directly into a wall socket (100–240V~). Do not use an extension cord between this
product and the AC power source.
9. When plugging this product into a wall socket, make sure that the electrical socket is not damaged,
and that there is no gas leakage.
10. Place the connecting cables properly so that people won’t stumble or walk on it.
11. This product should be operated from the type of power indicated on the marking label. If you are not
sure of the type of power available, consult the qualified technician.
12. Unplug this product from the mains and refer the product to qualified service personnel for the
following conditions:
¾ If liquid has been spilled on the product
¾ If the product has been exposed to rain or water
13. Unplug this product from the wall socket before cleaning. Use a damp cloth for cleaning. Do not use
liquid cleaners or aerosol cleaners.
14. The specification of the fuse is T2.5AL250V. To avoid damage, please do not change the fuse.
15. The Operating temperature is 0℃~40℃ (32℉~104℉).
16. The Storage temperature is -40℃~70℃ (-40℉~158℉).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Chapter 2 Connecting Mechanism
2.1 Introduction
The Powerline Adapter supports up to 200Mbps data rate. With this high speed connection rate, this
Powerline Adapter allows you to setup a high speed home network by using your home existing
electrical wiring. Simply plug this Powerline Adapter into an ordinary power outlet to extend your
Cable/xDSL broadband connection or existing LAN network to any other electrical outlet in any rooms of
your house.
Note that this Powerline Adapter works in pairs. You need to plug one Powerline Adapter into a power
outlet for each computer (Connect to the computer LAN card) you want to connect (Network access);
you will also need another Powerline Adapter connected to your Cable/xDSL broadband (Ethernet port)
in order to extend your broadband connection or Internet surfing. With clean powerline, the distance
between two Powerline Adapters can reach 300 meters at lease, but the actual distance may vary due
to the environment.
Section below describes the Powerline Adapter’s LED indicators, physical interface and hardware
connection mechanism.
2.2 LED Indicator
The LED indicator displays information about the device’s status.
Item
Status
Indication
On
The adapter is on.
Blinking The adapter is in pairing procedure.
Power LED
Off
On
The adapter is off.
The adapter is connected to a powerline network.
Blinking The adapter is transferring data.
Off The adapter isn’t connected to any powerline network.
Powerline LED
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
At least one Ethernet port is connected, but there is no
data being transferred.
On
Blinking At least one Ethernet port is transferring data.
Off No Ethernet port is connected.
Ethernet LED
2.3 Physical Interface
There are three physical interfaces on this Powerline Adapter.
Power Plug
Pair Button
Ethernet Port
Interface
Ethernet Port
Power Plug*
Description
Three 10/100Mbps Ethernet ports for connecting the adapter to the PC or
the broadband device with a network cable.
A Power Plug for connecting the adapter to a power socket (100–240V~).
Pair button is used to secure a powerline network. To secure your network,
please follow the steps below. Firstly, plug in a new adapter, and press its
pair button for 1 second; then plug in another adapter and press its pair
button for 1 second as well. The two buttons should be pressed within 2
minutes of each other. After that, wait about 60 seconds so that the two
adapters can finish connecting.
Pair Button
* The provided power plug may differ from the picture due to different regional power specifications.
Here we take the EU version of this product as an example.
Note:
)
1. If the pair button is pressed till all the LEDs turn off (about 10 seconds), the Powerline Adapter will
leave the network which it is associated with and its network name assumes a random value. The
Power LED turns off when it disconnects from the Powerline network.
2. For detailed information about the Pair button, please refer to Chapter 5 Advanced Feature: How to
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
2.4 Connection Instruction
To ensure the optimum performance of the Powerline Adapter and significantly improve the transmission
capacity of the network, we recommend that you comply with the following connection rule:
y
Plug the Powerline Adapter directly into a wall socket but not the multiple sockets.
2.5 Hardware Connection – Computer
For those computers you wish to be networked by Powerline Adapter, each of the computers must be
properly connected with a Powerline Adapter through an Ethernet (RJ45) cable.
Following are the steps to properly connect the Powerline Adapter to your computer:
1．Connect one end of the provided Ethernet (RJ45) cable to an Ethernet port of the Powerline Adapter.
2．Connect the other end of the Ethernet (RJ45) cable to you computer’s LAN port.
3．Plug the Powerline Adapter into a wall socket next to the computer.
4．Turn on your computer.
5．Check and confirm that the Power LED
and Ethernet LED
on the Powerline Adapter are
ON.
The hardware connection mechanism is shown below:
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
2.6 Hardware Connection – Internet
This section describes how to connect the Powerline Adapter into your existing ADSL broadband
connection via ADSL Ethernet port. Follow the procedures described below to connect the Powerline
Adapter to your ADSL broadband connection:
1．Connect one end of the provided Ethernet (RJ45) cable to an Ethernet port of the Powerline Adapter.
2．Connect the other end of the Ethernet (RJ45) cable to an available Ethernet port of your ADSL
broadband Router.
3．Plug the Powerline Adapter into a wall socket next to the computer.
4．Turn on your computer.
5．Check and confirm that the Power LED
, Ethernet LED
, and Powerline LED
on the
Powerline Adapter are ON.
The hardware connection mechanism is shown below:
)
Note:
Do not connect the Powerline adapter to an extension lead, power strip, extension cord, or surge
protector as these may degrade the network performance.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Chapter 3 Installing Management Utility
Please verify that no other Powerline Adapter or any Encryption Management Utilities are installed
before installing the provided software. If other Powerline Utilities are installed, uninstall them and
restart your personal computer before installing this provided software.
)
Note:
To install PowerLine Utility, please make sure that WinPcap (version 4.1.2 or higher) has been installed
in your computer. Otherwise, a window will pop up for you to install WinPcap 4.1.3.
Take the following procedures to properly install the provided Management Utility:
Step 1: Insert the Resource CD into your CD-ROM drive, and then the following Setup Wizard will
automatically pop up on your computer’s screen.
Step 2: Select 200Mbps Powerline and click Management Utility, and then the program installation
process will carry out and copy all the necessary files to your system.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Step 3: After the installation, a shortcut to the “Powerline Utility” application icon is provided on the
windows desktop.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Chapter 4 Using the Management Utility
After you’d successfully installed the Powerline Adapter hardware and Management Utility software, you
can set up or configure the devices according to your need.
This Powerline Utility enables the users to identify powerline devices on the powerline network,
measures data rate performance and ensures privacy by setting user defined secure powerline
networks.
Double click on the icon “
” from your windows desktop, the following screen will display. This
Management Utility consists of three property tabs, “Status”, “Network”, and “System”.
4.1 Status
The Status tab shows information of the powerline adapter connected to the current computer where
the Management Utility is running. On this page, you can also set its network name.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
¾
¾
MAC Address: Displays the MAC address of the powerline adapter connected to the current
computer where this management utility is running.
Network Name: Displays the network name of the current network or you can give a name for the
network in which the powerline adapter is. By default, the network name is HomePlugAV.
¾
¾
¾
Use Default (HomePlugAV): Check the box before this item to use the default network name.
Apply: Click the Apply button to make the setting effective.
Password: Displays the password of the current powerline adapter. Every powerline adapter has
its own password by default, which can be also found on the back of the adapter.
¾
¾
Firmware: Displays the current firmware version used by the adapter.
Refresh: Click the Refresh button to update the information.
4.1.1 Set Local Device’s Network Name
To set the local device’s network name, please take the following steps:
(1) Click Status tab to display the Status tab window.
(2) Enter a name for the current network using 4–23 characters. Or you can check the Use Default
(HomePlugAV) to use the default name as the network name. By default, the network name is
HomePlugAV.
(3) Click the Apply button to make the settings take effect.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
4.2 Network
The Network tab window shows information of all the powerline adapters found on the current logical
network. Furthermore, here you can change the Name of the listed powerline adapters as well as add
another device to the current network.
¾
¾
Type: Displays the type of the remote device found in the network.
Name: Displays the name of the remote device found in the network. You can change its name
following two steps: select the desired adapter and click the Modify button.
¾
¾
MAC Address: Displays the MAC address of the remote device found in the network.
Password: Displays the supplied Powerline Adapter’s password (Initially left blank). To set the
Powerline Adapter password (Which is required when creating a private network or managing all
the devices), select the device shown in the figure and click the Modify button. Follow the pop-up
dialog box to complete your password setting.
¾
¾
Rate: Shows the current transmission rate of the Powerline Adapter.
Rescan: Click the “Rescan” button to perform an immediate search of the remote Powerline
Adapter. The Management Utility will automatically perform the scanning process and update the
display every few seconds by default.
¾
Option: Select the device and click the Modify button to display a configuration dialog. There you
can change the corresponding adapter’s name and enter its password for future configuration.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
4.2.1 Rename the Remote Device/Enter Password
AV200 3-port Mini Powerline Adapter
You can change the name of the remote adapter to an easy-to-remember one. Additionally, you can
select the desired adapter and enter its password (Take note of the password format) so as to set the
network name of this device on System configuration homepage. To change the name of the remote
adapter or enter its password, please follow the steps below:
(1) Select the desired device and click the Modify button to display the following dialog.
(2) Enter a new name for the selected adapter and enter its password (Take note of the password
format). The password can be found on the back of adapter.
(3) Click the Save button to make the settings effective.
)
Note:
Password is unnecessary to enter for renaming.
4.2.2 Add Device
You can add a remote Powerline Adapter to your network that is not in the displayed list. You are
suggested to locate the passwords for all Powerline Adapters you wish to manage and add them to the
local logical network by clicking the Add button.
Click the Add button to display the following dialog box. This dialog box allows you to enter both the
selected device’s name and password. Note that the Powerline Adapter must be present on the power
grid in order to activate the set password and be added to the local network.
Enter your Device Name and Password (Take note of the password format) and click the Save button
after setup.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
4.3 System
The System tab window is for some basic settings of the adapter. On this tab window, you can upgrade
the firmware to the latest version, reset the adapter’s settings to the factory defaults and configure all
adapters’ network names.
4.3.1 Upgrade Firmware
Click the Upgrade Firmware button to upgrade the version of the firmware for the adapter and the
following dialog will pop up.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
z
z
NVM: None-volatile memory. It is used for upgrading the firmware.
PIB: Parameter Information Block. It contains configuration values that establish device
network identity, general capabilities and operational modes.
If you want to upgrade the version of firmware for the device, please select appropriate Firmware and
downloaded for free.
)
Note:
The parameter information of PIB will restore to the factory defaults after resetting the PLC.
To upgrade the device's firmware, follow these instructions:
2. Enter the path name or click
corresponding blanks.
to select the downloaded files on the computer into the
3. Click the OK button.
)
Note:
Do not turn off the device while the firmware is being upgraded. The device will reboot after the
Upgrading has been finished.
4.3.2 Reset Device
This Management Utility allows you to reset the Powerline Adapter to its default settings.
z
Reset Local Device: Click this button to reset the settings of the local Powerline Adapter device
only.
z
Reset All Devices: Click this button to reset the settings of all devices that appear on the
Network configuration homepage whose Device Password had been entered for the same
logical network.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
4.3.3 Set All Devices’ Network Name
The Set All Devices’ Network Name function allows you to change the logical network of all devices
that appear on the Network configuration homepage whose Device Password had been entered for the
same logical network. A dialog window will appear to report the success of this operation.
All Powerline devices are shipped using a default logical network (network name), which is normally
“HomePlugAV”.
To set all devices’ network name, please type the name in the field and click the Set Network Name
button to apply the setting.
Note:
)
Every Powerline Adapter on your home network MUST have the same Network Password for
connectivity to be established throughout your home.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Chapter 5 Advanced Feature: How to Use the Pair Button
5.1 Pair (Secure with 128 bits-AES)
The Homeplug AV standard uses 128-bit AES (Advanced Encryption Standard) to safely transmit data
between powerline adapters. For the powerline adapters to communicate with each other they all need
to use the same Network Membership Key (NMK). Otherwise, they cannot unscramble the encrypted
data sent in the powerline network.
The Pair button allows you to set up a secure powerline connection with other HomePlug AV compliant
powerline devices which also support the Pair feature.
5.2 Set Up a Powerline AV Network with the Pair Button
You can connect a number of devices on a powerline network, but you can use the Pair button on only
two devices at a time.
Create a Powerline network using the Pair button：
Step 1. Press and hold the Pair button of Powerline adapter A for 1 second, the Power LED will start
flashing.
Step 2. Press and hold the Pair button of Powerline adapter B for 1 second, the Power LED will start
flashing.
(This must be done within 120 seconds after pressing the Pair button of Powerline adapter A.)
Step 3. Wait for about 60 seconds while your Powerline adapter A and B are connecting. The Power
LED on both adapters will stop flashing and become solid light when the connection is made.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Join an existing Powerline AV Network:
Powerline adapter A and Powerline adapter B form a HomePlugAV Network, Powerline adapter C wants
to join this network.
Step 1. Press and hold the Pair button on Powerline adapter C for 1 second.
Step 2. Within 2 minutes, press and hold the Pair button on Powerline adapter A/B for 1 second.
Step 3. Wait for about 60 seconds while your Powerline adapters are connecting. The Power LEDs on
Powerline adapter A/B and C will stop flashing and become solid light when the connection is
made.
)
Note:
The sequence of Step 1 and Step 2 can be exchanged.
Leave an existing Powerline AV Network:
As the figure above shown, Powerline adapter A, B and C have formed a HomePlugAV Network. The
user wants to remove one device (Powerline adapter A) from this network.
Step 1. Press and hold the Pair button on Powerline adapter A for at least 10 seconds. Powerline
adapter A will reset and restart. (The Power LED of Powerline adapter A will momentarily
extinguish during resetting, flash during restarting, and then illuminate steadily.)
Step 2. Wait for the reset to complete.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-PA2030
AV200 3-port Mini Powerline Adapter
Appendix A: Troubleshooting
The Troubleshooting provides answers to common problems regarding the Powerline Adapter.
1. The Power LED
does not light up.
Ans. Check the following:
1. Make sure that the Powerline Adapter is properly plugged into a power outlet.
2. Make sure the power outlet is active (working) by plugging another electric device into it.
3. Re-plug the Powerline Adapter to the power outlet. If the Power LED is still failed to light up,
contact your local dealer for technical support.
2. The Ethernet LED
Ans. Check the following:
does not light up.
1. Make sure that the Ethernet cable (RJ45) is properly connected to an Ethernet port of the
Powerline Adapter.
2. Make sure that the other end of the Ethernet cable (RJ45) is properly connected to the
computer LAN card or to you Cable/xDSL Ethernet port.
3. Make sure your computer LAN card is properly installed and configured.
4. Make sure your Cable/xDSL broadband access is working and configured correctly.
5. Contact your local dealer for technical support if the Ethernet LED is still failed to light up after
the above procedures.
3. The Powerline LED
does not light up.
Ans. Check the following:
1. Double click to enable the Management Utility and click the “Rescan” button under the
Network configuration homepage. The Management Utility will automatically detect all other
Powerline Adapters on your powerline network.
2. Try to plug a second Powerline Adapter into a nearby power outlet and check whether the
Powerline LED lights up or not.
3. Contact your local dealer for technical support if the Powerline LED is still failed to light up after
the above procedures.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|