INSTALLATION MANUAL
OUTDOOR COMBINATION CAMERA
C-CC714 NT
C-CC714 PL
C-CC764 NT
C-CC764 PL
Thank you for purchasing TOA’s Outdoor Combination Camera. Please carefully follow the instructions in
this manual to ensure long, trouble-free use of your equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
Do not leave the unit upside-down where it could be exposed to the
rain or elements. Water in the unit may cause shorts that could result
in fire or electrical shock.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
WARNING
When Installing the Unit
• Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is specified
may result in fire or electric shock.
• Do not cut, kink, otherwise damage nor modify the power supply cord. In addition, avoid using the power
cord in close proximity to heaters, and never place heavy objects (including the unit itself) on the power cord,
as doing so may result in fire or electric shock.
• Avoid installing the unit in unstable locations, such as on a rickety or slanted surface. Failure to do so may
result in the unit falling and possibly causing personal injury.
• Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.
• Only use the unit's dedicated mounting hardware. The use of mounting hardware not designated could result
in the unit falling and possibly causing personal injury.
• Do not install the unit in the following locations to avoid a traffic accident or personal injury.
Locations which block the driving of the car.
Locations where the traffic signal or road sign is hard to be seen.
• To prevent lightning strikes, install the unit at least five meters away from a lightning rod, and yet within the
protective range (angle of 45°) of the lightning conductor. Lightning strikes may cause a fire, electric shock
or personal injury.
• When installing the unit in the snowy area, take appropriate measures to prevent snow from lying on the
unit. If the snow lies on the unit, the unit may fall, causing personal injuries.
• Be sure that at least two persons are available to install the unit. Failure to do so could result in personal
injury.
• Do not use any methods other than specified to mount the bracket. Extreme force is applied to the unit and
the unit could fall off, possibly resulting in personal injuries.
• Attach the safety wire to the unit. If not attached, the unit could fall off, resulting in personal injury.
• Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so
may cause the unit to fall, resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
When Installing the Unit
• Avoid installing the unit in locations exposed to sea breeze or corrosive gas. Mounts may become corroded,
eventually causing the unit to fall off, which could result in personal injury.
• Do not mount the unit in locations exposed to constant vibration. The mounting screws and/or bolts may be
loosened by excessive vibration, potentially causing the unit to fall, which could result in personal injury.
• Avoid installing the unit at heights exceeding 16 meters above the ground since the unit could be exposed to
unexpected strong winds that might cause it to fall or result in other accidents.
When the Unit is in Use
• If any of the following irregularities occurs, immediately unplug the power plug from the AC outlet and inform
the shop from where the unit was purchased. Further using the unit may result in fire or electric shock.
· If you detect smoke or a strange smell coming from the unit.
· If water or any metallic object gets into the unit
· If the unit falls, or the unit case breaks
· If the power supply cord is damaged (exposure of the core, disconnection, etc.)
· If no camera images are displayed on the monitor TV when the temperature of the camera unit is 0°C or
more.
• To prevent a fire or electric shock, never open nor remove the unit case as there are high voltage
components inside the unit. Refer all servicing to your nearest TOA dealer.
• Do not insert nor drop metallic objects or flammable materials in the ventilation slots of the unit’s cover, as
this may result in fire or electric shock.
• Do not touch a power cable during thunder and lightning, as this may result in electric shock.
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
When Installing the Unit
• To avoid electric shocks, be sure to switch off the power before power supply wiring work. Failure to do so
may result in electrical shock.
• Leave the installation of the unit to your TOA dealer because the installation requires expert experience and
skills. If the unit falls, this could cause personal injures.
When the Unit is in Use
• Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
• Switch off the power, and unplug the power supply plug form the AC outlet for safety purposes when
cleaning or leaving the unit unused for 10 days or more.
• Doing otherwise may cause a fire or electric shock.
• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in
corrosion or damage to the unit or its mounting brackets that could cause the unit to fall, possibly causing
personal injury.
• Contact your TOA dealer as to the cleaning. If dust is allowed to accumulate in the unit over a long period of
time, a fire or damage to the unit may result.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. GENERAL DESCRIPTION
TOA’s dome-type color cameras combine with a high-speed camera drive that permits one 360-degree
horizontal rotation per second and a 22 times (C-CC714) or a 23 times (C-CC764) optical zoom lens. Up to
255 arbitrary positions can be preset and such preset positions can be instantaneously repeated. The systems
also feature a 12 times electronic zoom, timer, and tracing, while the C-CC764 offer additional functions that
include a motion detector, auto flip, black & white mode, and privacy masking. Because all these cameras are
integrated with a weather-resistant outdoor-use housing and a built-in fan heater, they can be freely used
outdoors as well.
3. FEATURES
• Digital signal processing realizes high resolution and high picture quality. The unit also features the video
memory that increases the electronic sensitivity up to 32 times and enables electronic zooming.
• One coaxial cable used for connection between the Combination Camera and the System Controller permits
manual operations of the zoom lens, pan/tilt head, and preset camera positions, and the setting of the
camera functions. Also it can correspond to the control using a communications line of RS-485.
• Up to 255 camera positions can be preset.
• Built-in fan heater automatically turns on to keep the camera operable when temperatures decrease.
• Featuring IP66 (IEC60529) compliant dustproof and waterproof.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. HANDLING PRECAUTIONS
• Noise may appear on the monitor or preset camera positions may deviate with prolonged camera use. In
such cases, use the camera’s refresh function to automatically refresh settings and reestablish the home
position once a day or week, thus allowing any position deviation to be corrected. When correcting manually,
initialize the camera from the remote controller.
• The AC line is equipped with a surge protector to protect the camera against lightning strikes and other
power surges. Therefore, remove the surge grounding terminal’s connector when conducting withstand
voltage tests, and be sure to replace it after the test is completed.
• It is recommended that the unit be installed in locations where the temperature is under +40°C, as the
longevity of the unit may reduce with prolonged unit use under high temperature and high humidity.
• Because the dome camera uses sealed construction, moisture can accumulate inside the camera, possibly
causing the inside of the dome to fog. Take care to install the camera when humidity conditions are low.
• Camera images may not immediately be displayed if the power is switched on when the temperature of the
camera unit is below 0°C. In such cases, wait for a while with the power switched on. When the temperature
inside the enclosure reaches 0°C or higher, normal operation becomes possible after initialization. Note that
it could take an hour or two before operation becomes possible when the ambient temperature is –40°C or
below.
• Even in locations where the temperature is higher than –40°C, if exposed to strong winds and snow, the
snow or ice on the transparent camera dome might not defrost. In such cases, it might be best to leave the
power to the camera on at all times.
• Do not direct the camera lens to the sun or strong lighting or light reflection.
• Do not install the unit in locations exposed to constant vibration. The units are not designed for vehicle use.
Do not install the unit in a vehicle nor ship.
• Mount the unit to a concrete wall or robustly constructed wall surface that can sufficiently withstand the
weight of the units. When mounting the units to a pole, pay special attention to the sway and strength of the
pole, and mount it securely at an appropriate height that will not cause the pole to sway and possibly
weaken it. Moreover, avoid mounting the units to a pole on which other objects susceptible to wind are also
mounted.
• Bolts and nuts used to install the unit to a ceiling, or on a wall or pole are not supplied with the unit. Be sure
to prepare bolts and nuts keeping the ceiling’s or wall’s structure and material, gross weight, etc in mind.
• Do not give vibration or shock to the unit, as doing so may cause unit breakdown, damage or be leakage.
Giving vibration or shock may cause damage or leakage to the unit.
• Avoid installing the units on sea or shore, or in locations exposed to corrosive gas, herbicides or other
sprayed liquid chemicals, or extraordinary combustible conditions.
• To prevent the unit falls off, be sure to hang the safety wire first when installing the unit.
• The dome camera is designed solely for suspended installations. The camera or dome must be suspended
vertically with its dome facing downward. Use special care not to suspend it at a tilted angle.
• The dome camera is not equipped with a power switch. Perform power construction work so that the camera
power can be turned on and off remotely.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• The dome camera features built-in heat generating circuitry. Take care not to touch the internal parts marked
“Caution! High Temperature” when working inside the camera during dome cleaning or maintenance .
• Avoid directly touching the dome surface, since camera picture quality could deteriorate if the dome cover
becomes smudged and dirty.
• To clean, be sure to first unplug the power plug from the AC outlet, then wipe with a dry cloth. When the unit
gets very dirty, use a cloth dampened in a neutral detergent. Never use benzene, thinner or chemically
processed towel as the unit's plastic or other parts may be deformed or discolored.
• When cleaning the dome cover, wipe lightly with a soft cloth. In this event, the cover could be scratched and
damaged if the dome is covered in dust or sand. When the cover is extremely dirty, it is highly recommended
that the cover be removed and that its outside surface be washed lightly with water. Since alcohol-based
detergents can turn the dome cover whitish, avoid using them, as camera picture quality could be severely
affected.
• When dust has settled on the unit's lens, lightly clean using a commercial camera blower or cleaning paper.
NTSC version complies with Part 15 of the FCC Rules.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Modifications
Any modifications made to this device that are not approved by TOA Corporation may void the authority
granted to the user by the FCC to operate this equipment.
Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the security aspects
of this product. UL has only tested for fire, shock or casualties as outlined in UL's Standard(s) for
Safety. UL Certification does not cover the performance or reliability of the security hardware and
security operating software. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY
SECURITY RELATED FUNCTIONS OF THIS PRODUCT.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. NOMENCLATURE
[ Appearance ]
[ Camera Unit Appearance ]
1
3
2
4
6
5
[ Camera Unit Bottom ]
[ Housing Appearance ]
15
14
13
7
9
9
8
[ Camera Unit Top ]
[ Housing Bottom ]
11
19
9
9
16
10
17
9
9
18
11
19
20
12
8
Download from Www.Somanuals.com. All Manuals Search And Download.
[ C-BC711W Wall Mounting Bracket (optional) ]
[ C-BC711P Suspension Bracket (optional) ]
23
21
22
22
[ C-BC711PM Pole Mounting Bracket (optional) ]
24
(1) Top cover
(14) COM LED*
(2) Safety wire for housing
(3) Housing adaptor
(4) Safety screw
(15) COM PORT*
(16) DIP switch (SW1)
(17) DIP switch (SW2)
(5) Dome cover
(18) DIP switch (SW3)
(6) Decorative frame
(7) Sunshade (Outside)
(8) Case (Inside)
(19) Camera unit mounting hole
(20) Safety wire for camera unit
(21) Wall mounting bracket
(22) Hook to connect safety wire for housing
(23) Suspension bracket
(24) Pole mounting bracket
(9) Hexagon sleeve
(10) Safety wire for dome cover
(11) Camera unit fixing screw
(12) Surge protector GND
(13) COM SW*
* For handling of (13), (14) and (15), refer to the “Camera Controller Software Operation Manual” of the
enclosed CD-R.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. CONNECTIONS
Power cable
Connects to the power supply. (24V AC 50/60 Hz)
Alarm input/output terminal (No. 1 - 5)
Connects to the sensor of no-voltage make contact or the external equipment
that can be controlled using the auxiliary output.
Camera control terminal (No. 6 - 8)
Connects to cables from the Remote Controller or other camera when
controlling the camera using the RS-485 communications line.
Wire color Dot color Terminal name
1
2
3
4
5
6
7
8
Orange
Orange
Yellow
Yellow
Green
Green
Gray
Black
Red
GND
Alarm input 3 (AL3)
Alarm input 2 (AL2)
Alarm input 1 (AL1)
Auxiliary output (AUX)
GND
Black
Red
Black
Red
Black
Red
RS485 (–)
Gray
RS485 (+)
Video output cable
When controlling with use of the RS-485 communications line,
connect this output cable to the video input terminal of the multi-switcher
or monitor.
Note: The length of power cable, video output cable and multi wick cable is about 1.8 m.
6.1. Precautions When Installing the Camera
• Insulate the joint of the camera video output cable and the coaxial cable from other equipment by wrapping
the (vinyl) insulating tape around it. Also, install such cables taking care that they do not contact metal stuff
close to them.
Insulate with vinyl tape.
System controller,
Multi switcher, Monitor
• Avoid install the camera cable in close proximity to other cables of electric products, such as fluorescent
lamps. Failure to do this could downgrade the picture quality.
• Installing the camera near the strong electric or magnetic field produced by television transmitting antennas,
motors or transformers could distort or shake the monitor screen. In such cases, install the cables in the
sheet steel cable piping.
• Before applying the power to the camera, be sure to complete all connections between the camera and
related equipment.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2. Camera Control Connector Connection (RS-485)
• Connect terminals (+) and (–) of the C-RM500 Remote Controller or the C-IF500 Interface Unit to the
camera's terminals (+) (terminal No. 8) and (–) (terminal No. 7), respectively.
• Connect the camera's terminals (+) and (–) to the next camera's terminals (+) and (–) in order.
Notes
• The maximum number of units connectable to a pair of RS-485 lines (from termination to termination) is 32
units including the Remote Controller. The maximum cable length connecting each terminal is 1.2 km in
total.
• The camera may not operate correctly if 32 or more units are connected or the total cable distance exceeds
1.2 km. In such cases, split or extend wiring using the C-IF500 Interface Unit.
• Indoor-use and outdoor-use combination cameras can be wired in free combinations.
Shield twisted pair cable
Connect to the next
cameraʼs terminal
Connect to remote controllerʼs
camera control terminal
GND
GND
Camera control
cable
Camera control
cable
7. CAMERA SETTINGS
7.1. About AUX Output
Open collector output,
Rated: withstand voltage: 30 V DC,
Permissible current:
under 100 mA
7.2. About Alarm Input
No-voltage make contact input,
Rated: open voltage: 18 V DC,
Short-circuit current: under 2 mA
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7.3. Dip Switch Settings
DIP SW1
DIP SW2
DIP SW3
DIP SW1
DIP SW2
DIP SW3
Communication speed setting
switch 1
No.1
No.2
No.3
No.4
Camera address setting switch 1
Camera address setting switch 2
Camera address setting switch 3
Camera address setting switch 4
Firmware update switch 1
Communication speed setting
switch 2
Firmware update switch 2
Firmware update switch 3
OSD switch
Unused
Unused
Unused
No.5 Camera address setting switch 5
No.6
Unused
Communication method selector
switch
Camera address setting switch 6
Unused
Memory clear switch
No.7 Camera address setting switch 7
No.8 Camera address setting switch 8
Unused
Termination switch
Unused
Note
Set the unused DIP switches to the "OFF" position.
If the DIP switches are not set correctly, the camera does not operate correctly.
7.3.1. Camera Address Setting Switch (DIP Switch 1: No. 1 – 8)
Used to set camera address when using the camera in connection with the C-RM500 Remote Controller. Set
the DIP switch so that the address is equal to the connected switcher's channel number. The relationship
between switch settings and camera addresses are shown on page 14. (Factory setting: Only No.1 is “ON”.)
Note
If the address switch number does not match with the connected switcher's channel number or if set to the
same number as that of other camera connected to the same system, the system does not operate correctly.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
7.3.2. Communication Speed Setting Switch (DIP switch 2: No. 1 – 2)
Check to be sure that the communication speed set here is the same as that of the Remote Controller. When
changing the speed, change settings of all cameras and Remote Controller within the system. (Factory
setting: 38,400 bps.)
No.2
No.1
bps
OFF OFF 38400
O N OFF 19200
OFF O N
O N O N
9600
4800
7.3.3. OSD Switch (DIP switch 2: No. 3)
When this switch is set to the OFF position, the initial screen does not disappear until communications with
other equipment are established following initial operation after the power has been switched ON. (Factory
setting: OFF)
7.3.4. Communication Method Selector Switch (DIP switch 2: No. 6)
Chooses the RS-485 communication method from Type A (used with the C-RM500 Remote Controller) and
Type B. Set the switch to the OFF position to choose Type A, and to the ON position to choose Type B.
(Factory setting: OFF)
7.3.5. Termination Switch (DIP switch 2: No. 8)
Set the switch of the camera last connected to the RS-485 communications line to ON. (Factory setting: OFF)
7.3.6. Firmware Update Switch (DIP switch 2: No. 1 – 3)
No.1: Used to update Master CPU firmware.
No.2: used to update Slave CPU firmware.
No.3: Temporarily pauses the initial operation.
More particularly, refer to the “Camera Controller Software Operation Manual” of the enclosed CD-R.
7.3.7. Memory Clear Switch (DIP switch 3: No. 7)
Switching on the power with this switch set to the ON position returns all camera settings to the initial setting.
The indication “Memory Clear” is displayed on the screen while clearing memory. After the indication has
disappeared, turn off the power and set the switch to the OFF position.
Note: Clock information and backup data are not erased.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
[ Camera address setting switch: 1 - 64 ]
DIP switch 1
DIP switch 1
DIP switch 1
DIP switch 1
No.
No.
No.
33
No.
49
ON
ON
ON
ON
1
17
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
ON
ON
ON
ON
2
3
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
4
1
1
1
1
ON
ON
ON
ON
5
1
1
1
1
ON
ON
ON
ON
6
1
1
1
1
ON
ON
ON
ON
7
1
1
1
1
ON
ON
ON
ON
8
1
1
1
1
ON
ON
ON
ON
9
1
1
1
1
ON
ON
ON
ON
10
11
12
13
14
15
16
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
14
Download from Www.Somanuals.com. All Manuals Search And Download.
[ Camera address setting switch: 65 - 128 ]
DIP switch 1
DIP switch 1
DIP switch 1
DIP switch 1
No.
No.
No.
97
No.
113
ON
ON
ON
ON
65
81
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
ON
ON
ON
ON
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
98
99
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
100
101
102
103
104
105
106
107
108
109
110
111
112
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
15
Download from Www.Somanuals.com. All Manuals Search And Download.
[ Camera address setting switch: 129 - 192 ]
DIP switch 1
DIP switch 1
DIP switch 1
DIP switch 1
No.
No.
No.
161
No.
177
ON
ON
ON
ON
129
145
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
ON
ON
ON
ON
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
[ Camera address setting switch: 193 - 255 ]
DIP switch 1
DIP switch 1
DIP switch 1
DIP switch 1
No.
No.
No.
225
No.
241
ON
ON
ON
ON
193
209
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
ON
ON
ON
ON
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
242
243
244
245
246
247
248
249
250
251
252
253
254
255
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
ON
1
1
1
1
ON
ON
ON
1
1
1
17
Download from Www.Somanuals.com. All Manuals Search And Download.
8. INSTALLATION
The Combination Camera weight 4.4 kg. Select the heavy-duty
mounting surface that can structurally support the weight of the
camera. Doing otherwise may result in the unit falling and possibly
causing personal injury.
WARNING
8.1. About Installation
• Mount the camera to a heavy-duty wall surface using the optional C-BC711W Wall Mounting Bracket.
• When installing the camera on a pole, use the optional C-BC711W Wall Mounting Bracket, C-BC711PM
Pole Mounting Bracket and 2 YS-60B Mounting Bands in combination.
• Mount the camera to a heavy-duty ceiling surface using the optional C-BC711P Suspension Bracket.
Note
Perform presetting beforehand when controlling the camera using the RS-485.
(refer to p.11 “Camera Settings”.)
8.2. Installation Method
The camera can be mounted on a wall, a pole or be suspended from a ceiling.
More particularly, refer to each related pages.
[ Wall mounting view ]
[ Pole mounting view ]
[ Suspension view ]
Refer to p.19
Refer to p.27
Refer to p.28
18
Download from Www.Somanuals.com. All Manuals Search And Download.
8.3. Wall Mounting Bracket Installation
Use the optional C-BC711W Wall Mounting Bracket.
Notes
• Check to be sure that wall surface can structurally support the weight of the camera and mounting bracket
• Bolts, nuts and washers are not supplied with the bracket. Use bolts, nuts and washers that are appropriate
for the wall's structure and composition.
• Be sure to hang the safety wire first when installing the unit.
1. Make a cable entry hole of ø 50 – 100mm on a wall.
Wall surface
C-BC711W
(optional)
ø50 – 100 mm
2. Run the cables to be connected to the camera through the wall mounting bracket, then fix the bracket on a
wall.
Nut
Spring washer
Plain Washer
ll surface
a
W
Cable entry hole
Anchor bolt (M8, M10 or W3/8)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
8.4. Attaching Housing and Camera Unit to Wall Mounting Bracket
1. Loosen 2 safety screws.
Safety screw
Safety wire
Safety screw
Housing
2. Run the safety wire through the top cover, then hang the hook to the mounting bracket.
3. Run the top cover through the pipe, then connect cables.
Wall surface
Top cover
Safety wire
Insulate the terminals by
wrapping the (vinyl) insulating
tape around it.
Housing
Refer to p.10 “Precautions
when installing the camera”.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4. After confirming the housing direction, push the housing up, then tighten 2 safety screws.
Safety screw
Top cover
Align the
hole positions.
Safety screw
Housing
5. Using the 3 supplied camera mounting screws M5 x 12, attach the housing unit to pipe.
Tighten 3 screws equally and ensure that no parts rattle.
Note: In this event, tighten screws while pressing the housing against the pipe.
Figure viewed from the top.
Camera mounting screw
Safety screw
Camera
mounting screw
Camera mounting screw
M5 x 12 (with washer and spring washer)
(supplied with the C-BC711W)
Camera
Safety screw
mounting screw
Housing
21
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using the supplied 3 hexagon socket screws, attach the top cover 1 to the housing.
Hexagon socket screw
M4 x 8 (supplied with)
Hexagon socket screw
M4 x 8 (supplied with)
7. Connect the safety wire to the housing projection, then attach the camera unit.
Note: Align
mark of the camera unit with that of the housing when attaching the camera unit to the housing.
Aligning the positioning marks
at the time of camera unit fixation
Camera unit
Hang the safety wire.
mark
Safety wire
Duct
Black screw
When attaching the camera unit, align the arrow
on the label with the black screw on the duct.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Insert the camera unit in an oblique direction in the order of 1 to 2 keeping away from the duct of the housing.
1
2
mark
Duct
8. Make the camera unit in horizontal position and push it straight up closely to the housing.
Cross sectional view
of the housing
Camera unit
Push the camera unit
straight up closely
to the housing.
Screw section inside of the housing
is to be inserted into the oval hole
in the camera unit.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Do not allow the safety wire to protrude from the compartment of the camera unit. Damage may be caused to
the wire if it protrudes.
Safety wire protrudes
from the compartment.
Safety wire does not protrude
from the compartment.
Note
When mounting the camera unit to the housing, mount it straight till it is attached to the housing correctly.
Mounting it at an angle may cause damage to the camera unit.
Cross sectional view
Cross sectional view
of the housing
of the housing
Camera unit
Camera unit
Mount straight
24
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Rotate the camera unit until it locks into place.
10. Tighten 2 camera unit mounting screws to attach the camera unit to the base unit.
Camera unit
mounting screw
Camera unit
mounting screw
11. Attach the dome cover.
Slide down the dome cover’s screw head through the housing suspension fitting’s slot.
Hang
25
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Align the dome cover’s 4 screws with the hexagon head sleeves inside the housing.
Note
Be sure to attach the dome cover after sliding down its screw head through the housing suspension fitting’s
slot so that the dome cover can be attached securely to the housing.
Hexagon head
sleeve
Hexagon head
sleeve
Rib
Rib
Dome cover
13. Tighten 4 screws equally to attach the dome cover to the housing and ensure that the dome cover does
not rattle.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
8.5. Pole Mounting Bracket Installation
The optional C-BC711PM Pole Mounting Bracket, C-BC711W Wall Mounting Bracket and YS-60B Mounting
Band are required to mount the camera on a pole.
Note
Those mounting brackets and band can be installed on a pole having a mounting pipe diameter of 90 - 340
mm. Be sure to use 2 mounting bands. If mounting band is too long, cut it.
1. Insert the optional mounting bands into the pole mounting bracket’s slots, then attach the band to a pole.
YS-60B Mounting Band
(optional)
C-BC711PM
(optional)
Hexagon head bolt
(M8, M10 or W 3/8)
2. Attach the wall mounting bracket to the pole mounting bracket.
Note: Bolts, nuts and washers for fixing are not supplied with the bracket.
Nut
Spring washer
Plain washer
C-CB711W
Wall Mounting Bracket
(optional)
YS-60B
Mounting Band
(optional)
Hexagon head bolt
(M8, M10 or W 3/8)
3. For installation procedures of the housing, camera unit and the dome cover, refer to p.20 as the procedures
are the same as that of wall mounting.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
8.6. Suspension Bracket Installation
The C-BC711P Suspension Bracket is required to suspend the camera from a ceiling.
Note
Mount the bracket to a concrete wall or robustly constructed wall surface that can sufficiently withstand the
weight of the units.
1. Make a cable entry hole of ø 50 – 100mm on a ceiling.
Hole diameter: ø 50 – 100mm
C-BC711P
(optional)
2. Attach the suspension bracket to a ceiling.
Note: Bolts, etc. are not supplied with the bracket.
Ceiling surface
Anchor bolt
M8, M10 or W 3/8
Plain washer
Spring washer
Nut
3. For installation procedures of the housing, camera unit and the dome cover, refer to p.20 as the procedures
are the same as that of wall mounting.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
9. SYSTEM EXAMPLES
[ RS-485 Communications line control ]
Combination camera
Monitor TV
Multi-switcher
Outdoor combination camera
Dedicated Remote controller
Note
Combination cameras and outdoor combination cameras can be used in free combinations. When a camera
(fixed installation*1 ) is used in combinations, the corresponding camera screens can be controlled by the
switcher only.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
10. SPECIFICATIONS
Model
Power Source
Power Consumption
Control system
Video Output
C-CC764 NT
24 V AC, 50/ 60 Hz (2P loose end)
10 W (normal operation), 80 W max.
RS-485 communications system (new protocol compatible)
VBS 1.0 V(p-p), 75 Ω, BNC-R jack
C-CC764 PL
Camera Control Terminal
Alarm Input
RS-485 camera control connector, multi-pair cable 8P loose end (3P out of 8P)
3-channels, no-voltage make contact input, open voltage: 18 V DC,
short-circuit current: under 2 mA(settable alarm action), multi-pair cable 8P
loose end (3P out of 8P)*1
Auxiliary Contact Output 1 channel, open collector output, withstand voltage: 30 V DC,
permissible current: under 100 mA, multi-cable 8P loose end (3P out of 8P)*1
Synchronization
Internal synchronization/ power synchronization (phase adjustable when in
power synchronization mode)*2
each 8 alphanumeric character,
ID
camera/ position/ trace/ auto-panning/ tour/ home/ sector/ AUX
255 positions *1
Auto-panning, Preset Sequence, Trace (2 patterns (60 sec.) possible to
memorize), Tour (possible to memorize 16 patterns)
Refresh: Start at the preset time every day or every week by timer settings
Program: Settable 16 actions
No. of Preset Positions
Automatic operation
Timer
Camera
Image Device
Resolution Horizontal
S/N Ratio
1/4 type CCD
Horizontal: 480 lines (at center)
50 dB
High-sensitivity function OFF: 3 lx (50IRE), 1 lx (20IRE)
High-sensitivity function ON: 0.03 lx (50IRE), 0.01 lx (20IRE)
Minimum Illumination
Backlight Compensation wide dynamic/ pattern 1/ pattern 2/ pattern 3/ OFF
Dynamic range
46 dB (Backlight compensation: when wide dynamic ON)
High-Sensitivity Function B/W mode, Slow shutter mode (32 times max.)
White Balance
Flicker Reduction
Electronic Zooming
Auto-Focus
ATW/ AWB
Automatic correction
12 x zooming
One push/ stop AF/ continuous
Lens
Zooming
Effective Focal Length
23 x
f = 3.6 – 82.8 mm (23 times)
Effective Horizontal Horizontal: 54° (W) – 2.5° (T), Vertical: 41.6° (W) – 1.9° (T)
View Angle
Maximum Aperture
Zooming Speed
F 1.6 (W) – 3.7 (T)
WIDE end to TELE end
Approx. 1.5 s (preset operation), Approx. 2.9 s (manual operation)
Pan/Tilt Head
Rotating Range
Rotating Speed
Other Functions
Panning: endless 360° rotation, Tilting: +5° to –185°
Panning/ Tilting: 360°/s max. (preset operation), 360°/s max. (manual operation)
Auto-flip, Freeze preset, Manual limit, Privacy masking (up to 8), Motion detect
(each 8 presets at each 4 positions)
Operating Temperature
Operating Humidity
Applicable Place
–40 to 50°C
Under 90% (no due condensation produced)
Indoors/ outdoors (avoid installing the unit on shore, in industrial area or in
locations exposed to corrosive gas, fine particles or unexpected strong wind.)
IP66
Dustproof/Waterproof
Capability
Finish
Case/ Top cover/ Decorative frame: PC resin, light gray
Sunshade: Aluminum, light gray, paint
Dome cover: PC resin (transparent)
Camera section external diameter: ø230 x 330.5 (H) mm
Dome external diameter: ø150 mm
4.4 kg
Dimensions
Weight
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
C-CC714 NT
24 V AC, 50/ 60 Hz (2P loose end)
10 W (normal operation), 80 W max.
RS-485 communications system (new protocol compatible)
VBS 1.0 V(p-p), 75 Ω, BNC-R jack
C-CC714 PL
Power Source
Power Consumption
Control system
Video Output
Camera Control Terminal
Alarm Input
RS-485 camera control connector, multi-pair cable 8P loose end (3P out of 8P)
3-channels, no-voltage make contact input, open voltage: 18 V DC,
short-circuit current: under 2 mA(settable alarm action), multi-pair cable 8P
loose end (3P out of 8P)*1
Auxiliary Contact Output
Synchronization
ID
1 channel, open collector output, withstand voltage: 30 V DC,
permissible current: under 100 mA, multi-cable 8P loose end (3P out of 8P)
Internal synchronization/ power synchronization (phase adjustable when in
power synchronization mode)*2
each 8 alphanumeric character,
camera/ position/ trace/ auto-panning/ tour/ home/ sector/ AUX
255 positions
Auto-panning, Preset Sequence, Trace (2 patterns (60 sec.) possible to
memorize), Tour (possible to memorize 16 patterns)
Refresh: Start at the preset time every day or every week by timer settings
Program: Settable 16 actions
No. of Preset Positions
Automatic operation
Timer
Camera
Image Device
Resolution Horizontal
S/N Ratio
1/4 type CCD
Horizontal: 480 lines (at center)
50 dB
Minimum Illumination
High-sensitivity function OFF: 1 lx (50IRE), 0.3 lx (20IRE)
High-sensitivity function ON: 0.03 lx (50IRE), 0.01 lx (20IRE)
pattern 1/ pattern 2/ pattern 3/ OFF
Slow shutter mode (32 times max.)
ATW/ AWB
Backlight Compensation
High-Sensitivity Function
White Balance
Flicker Reduction
Electronic Zooming
Auto-Focus
Automatic correction
12 x zooming
One push/stop AF/continuous
Lens
Zooming
22 x
f = 4.0 – 88 mm (22 times)
Horizontal: 47.3° (W) – 2.2° (T), Vertical: 36.5° (W) – 1.7° (T)
Effective Focal Length
Effective Horizontal
View Angle
Maximum Aperture
Zooming Speed
F 1.6 (W) – 3.8 (T)
WIDE end to TELE end
Approx. 1.3 s (preset operation), Approx. 2.4 s (manual operation)
Pan/Tilt Head
Rotating Range
Rotating Speed
Panning: endless 360° rotation, Tilting: +5° to –90°
Panning/ Tilting: 360°/s max. (preset operation), 360°/s max. (manual operation)
Other Functions
Operating Temperature
Operating Humidity
Applicable Place
Manual limit
–40 to 50°C
Under 90% (no due condensation produced)
Indoors/ outdoors (avoid installing the unit on shore, in industrial area or in
locations exposed to corrosive gas, fine particles or unexpected strong wind.)
IP66
Dustproof/Waterproof
Capability
Finish
Case/ Top cover/ Decorative frame: PC resin, light gray
Sunshade: Aluminum, light gray, paint
Dome cover: PC resin (transparent)
Camera section external diameter: ø230 x 330.5 (H) mm
Dome external diameter: ø150 mm
4.4 kg
Dimensions
Weight
*1 Either internal synchronization or power synchronization is selected when operated by the RS-485
communications control.
Note: The design and specifications are subject to change without notice for improvement.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
• Accessories
CD-R (CAMARA CONTROLLER Software, installation manual) ...... 1
Hexagon socket screw M4 x 8 ............................................................ 3
• Optional Products
Wall Mounting Bracket:
Suspension Bracket:
Pole Mounting Bracket:
Mounting Band:
C-BC711W
C-BC711P
C-BC711PM
YS-60B
Smoked dome cover:
C-A711DM
Printed in Japan
133-05-379-30
Download from Www.Somanuals.com. All Manuals Search And Download.
|