T0436-TV36 Revise-OM.qxp 11/11/03 03:53 AM Page 1
TV36 HDTV ANTENNA PRO
Owner’s Manual
Limited Warranty
TERK Technologies Corp. (TERK) warrants this product against
defects in materials or workmanship for one (1) year from the date of
purchase. During this warranty period, this product will be replaced
without charge. This warranty does not cover any damage due to acts
of nature, commercial use, accident, misuse, abuse or negligence.
This warranty is only valid in the USA. Replacement as provided
under this warranty is the exclusive remedy of the consumer. TERK
shall not be liable for any incidental or consequential damages for
breach of any express or implied warranty on this product, except to
the extent that limitations of this sort are prohibited by applicable
law. THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURCHASE EXCEPT TO THE EXTENT
THAT IMPLIED WARRANTIES OF EITHER SORT ARE REQUIRED BY
APPLICABLE LAW, AND IN SUCH CASE, EACH WARRANTY IS LIMITED
IN DURATION TO ONE YEAR.
Performance Specifications
Type:
HDTV/UHF/VHF/FM
Active Elements:
Antenna Selector:
Dimensions:
Height:
33
Blue
1
2
25 / "
Width:
Length:
111"
103 / "
1
4
Turning Radius:
69”
TERK and TERK Technologies are trademarks of TERK Technologies Corp.
Commack, NY ©2003 TERK Technologies Corp. Made in USA.
For additional information: call 1.800.942.TERK (8375) or visit
113P006A
1450190
Medium Directional
UHF/VHF/FM Antenna
TERK is a registered trademark. The TERK logo is a trademark of the TERK Technologies Corp.
Download from Www.Somanuals.com. All Manuals Search And Download.
T0436-TV36 Revise-OM.qxp 11/11/03 03:53 AM Page 3
Antenna Assembly
Antenna Assembly
(continued)
1. Unfold the elements on the two reflector booms until they lock
into place. Make sure that they are straight and perpendicular to
the boom.
2. Attach the two reflector booms using the attached nut and bolt so
that they are perpendicular to the smaller boom. (See figure 1.)
Large Boom
Small Boom
Fig. 1
Reflector Booms
3. Unfold the reflector booms until they lock into place.
(See figure 2.)
Mast
Fig. 2
4. Unfold all the other elements on the antenna until they lock into
place ensuring that they are flat and parallel to each other. (See
figure 3.)
Fig. 3
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
T0436-TV36 Revise-OM.qxp 11/11/03 03:53 AM Page 5
Antenna Assembly
(continued)
Antenna Assembly
(continued)
7. Loosen the nuts on the downlead connections. Attach the transformer
ends to the studs, between the washers, and tighten the nuts securely.
(See figure 6.) Attach the coax downlead to the transformer.
5. Find the large antenna section and remove the nut and bolt.
Slide the narrow boom into the larger section. Tap lightly with
a rubber mallet on the end of the small boom aligning the bolt
holes. (See figure 4.) Re-install the bolt and nut; be sure to
tighten it securely.
NOTE: Make sure that the side of the small boom with the phasing lines
line up with the nuts on the large boom.
Fig. 6
Fig. 4
Transformer
6. Remove the nuts and washers from the first element holder
studs of the large section on the bottom of the antenna. (See
figure 5.) Place the phasing lines from the front section over
the studs, and re-attach the washers and hex nuts. Tighten
them securely.
Phasing Lines
Downlead
Connections
Fig. 5
5
6
Underside View of Antenna
Download from Www.Somanuals.com. All Manuals Search And Download.
T0436-TV36 Revise-OM.qxp 11/11/03 03:53 AM Page 7
General Installation Instructions
for Mast Mounted Antennas
Antenna Assembly
(continued)
8. Loosen the U-bolt nuts, slide the TV36 antenna over the mast and
lightly tighten the mast clamp. (See figure 7.)
1. Assemble your antenna on the ground at the installation site
per the instructions.
2. On the ground, attach the antenna to the mast. Pull enough
coax downlead and connect to the antenna per its instructions.
3. To insure that the mast does not fall, a durable nonconductive
rope should be attached to each ten foot section as it is raised.
4. Install the selected mounting bracket.
NOTE: The top side of the antenna is the side with the black plastic pieces
on top of the large boom.
5. If you are using guy wire installation (not included) instead of
a mounting bracket:
Fig. 7
• Install guy anchor bolts.
• Estimate length of guy wire and cut.
• Attach to mast using a guy ring.
6. Carefully take the antenna and mast assembly to the mounting
bracket and insert. Tighten the clamp bolts. In case of a guyed
installation, it will be necessary to have at least a second
person hold the mast upright while the guy wires are attached
and tightened to the anchor bolts.
9. Connect the coax downlead to your TV. Rotate the TV36 antenna
until you receive the best picture. You will probably need a helper to
view the TV set while you are rotating the antenna. See “Pointing the
Antenna Towards the Broadcast Tower”
Antenna Removal
Removal of the antenna should be exactly the reverse of the
installation instructions. Please, for your own safety, follow
the instructions for installing the antenna starting with the last
step first.
Point this end
towards the
broadcast tower
NOTE: Point the small end of the antenna towards the station
broadcast tower.
10. Tighten the mast clamp securely.
11. Secure the coaxial downlead to the mast (using cable ties) to prevent
it from whipping by the wind.
12. Ground the antenna and mast per the accompanying grounding
instructions. (See page 14.)
Pointing the Antenna Towards the Broadcast Tower
2. Enter your home address and then “Submit.”
3. Click “View Street Level Map” to see in which direction you
should face your antenna.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
T0436-TV36 Revise-OM.qxp 11/11/03 03:53 AM Page 9
Types of Support Structures
and Mounting
Where To Install Your Antenna
Before attempting to install your antenna, decide on the
best location to install your antenna for both safety and
performance. To determine a safe distance from wires, power
lines and trees:
Chimney Mount - Mounts on a chimney only
1. Measure the length of your antenna and multiply by 2.
2. Add this measurement to the length of your tower/mast.
If you are unable to maintain this safe distance, STOP! Get
professional help. Most antennas are supported by tripod
masts or pipe masts attached to the chimney, roof, or to the
side of the house. Generally, the higher the antenna, the better
it performs. Good practice is to install your antenna about 5
to10 feet above the roof line and away from power lines and
other obstructions.
NOTES:
• Remember when doing any installation, keep the
mast plumb.
• For mast support, use only 1-1/4” O.D. pipe or larger antenna
mast sections. Lengths over 10 feet should be guyed at least
every 10 foot section.
Suggested height limitation: 10 feet above chimney top.
The chimney is often an easy and convenient mounting place,
but the chimney must be strong enough to support the
antenna in high winds. Do not use a chimney that has loose
bricks or mortar. A good chimney mount consists of a 5 or 10
foot 1-1/4” diameter steel mast and two heavy duty strap
clamp-type brackets.
• Not all mounting methods are shown here.
Read and follow the mount manufacturer’s instructions
carefully.
House Construction Obstacles:
For homes made of stucco, clad with aluminum siding or that have
internal foil paper insulation, the antenna must be installed on the
side of the house that faces the broadcasting tower. These
materials may prevent signals from going through it.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
T0436-TV36 Revise-OM.qxp 11/11/03 03:53 AM Page 11
Types of Support Structures
and Mounting
Types of Support Structures
and Mounting
(continued)
(continued)
1. Insert the threaded end of the strap hook, (the one secured to
the strap) through the end portion of the “Z” mount (hole A).
Take one of the loose strap hooks and insert into hole B.
Universal Mount - For attic installations
NOTE: It is important to thread the nut only 1/4” onto the hook, so
that it may later be tightened to take out the slack and make the
strap secure to the chimney.
2. Go around the chimney with the strap; slip the strap clip onto
the strap, and then secure the other end of the strap by inserting
the strap into the strap hook that is in hole B. The strap clip is
used as follows: (See figure 8.)
a. Slide the strap through the loop section of the clip and bend it
around through the upright section of clip.
b. Bend the upright sections of the clip down with pliers,
pinching the strap firmly.
3. At this time, remove any slack in the strap by tightening the nuts
at holes A and B.
4. Repeat the above steps to secure the lower mount to chimney.
(It is recommended that the mounts be a minimum of 18” apart.)
An attic installation is the easiest, fastest and most convenient type
of antenna installation, especially if you do not have easy or secure
access to an outdoor area. Attic installations work best in areas
where strong signals are present. Roofing materials, aluminum
foil on insulation, aluminum or steel siding, metal gutters at the
attic level, and metal lath under old plaster walls all can interfere
with reception. Use the universal mount to secure the mast and
antenna to a rafter.
NOTE: Install the upper bracket just below the top course of
bricks, and the lower bracket two or three feet below the upper
bracket. For maximum strength, space the brackets as far apart
as possible.
5. Place the mast against the mount and secure it in place using
the mast support clamps and nuts.
1. Screw the universal mount into a supported rafter
or beam.
2. Using the U-bolt, bracket and nuts, secure the mast to the
universal mount.
3. After you align the mast perpendicular to the floor, tighten
the nuts securely.
B
A
Fig. 8
B
A
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
T0436-TV36 Revise-OM.qxp 11/11/03 03:53 AM Page 13
Types of Support Structures
and Mounting
Example of Antenna
Grounding
(continued)
NOTE: Grounding the antenna and mast provides lightning protection for
the antenna and your TV set.
Wall Mount
All outdoor antenna installations should be properly grounded. To
effectively protect the installation, the coaxial cable(s) should be grounded
before they enter the house. The grounding of the coaxial cable is made
using a “ground block” and copper wire (not supplied). For information and
the materials needed to ground your antenna installation, visit your local
electronics store.
If you are not sure how to install the grounding block and rod, please
consult your local retailer or TERK’S Technical Support Department at
1-800-942-8375.
Suggested height limitation: 10 feet above the rooftop.
An outside wall of your home is also an easy and convenient
mounting place, but the wall and fasteners that you use must be
strong enough to support the antenna in high winds. Ensure that
the brackets are securely fastened to a solid part of your wall.
Antenna Lead
in Wire
Ground
Clamp
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
1. Space the mounting brackets on an exterior wall – be sure
to clear roof eaves or any other obstacles.
2. Secure the brackets to the wall using the 4 lag screws.
3. Insert the mast between the saddles and secure with the
nuts and bolts.
Grounding Wire Conductors
(NEC Section 810-21)
Electric
Service
Equipment
Antenna
Discharge Unit
(NEC Section 810-20)
Tripod Mount (not included) - Used on peaked and flat roofs
Suggested height limitation: 10 feet above the rooftop.
Installation involving a tripod mount and a mast should be guyed if
the mast is ten feet or more. The tripod mount must be securely
anchored to the roof as should the guy wires. Apply roofing
compound around the base of the brackets, screws and eyebolts to
weather proof the holes in the roof. Try to lag bolt the legs to the
roof rafters. If not, install wood plates in the attic and install bolts
to secure the mount.
Power Service Grounding
Rain Drip Loop On
Lead-in To TV
Electrode System
Ground
Clamps
(NEC Art 250, Part H)
NEC - National Electrical Code
1. Mount the 75 ohm grounding block or discharge unit as close as possible
to where the downlead enters the house.
2. The ground wires for both the mast and the downlead should be copper
or aluminum wire, number eight (8) or larger.
3. The downlead wire from the antenna to the antenna grounding block or
discharge unit and the mast ground wire should be secured to the house
with stand-off insulators, spaced from four (4) to six (6) feet apart.
Telescopic Mast (not included)
The minimum safe diameter of the mast is 1-1/4 inches for this
type of mount. Guy wires should be equally spaced in at least three
directions. Use at least three guy wires for each ten foot section
of mast. Make sure guy wires are spaced evenly apart.
NOTE: In the case of a “ground up” antenna installation, it may not be
necessary to ground the mast if the mast extends four or more feet into the
ground. Consult a TV serviceman for the proper depth in your location.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|