VXP SERIES
Professionalloudspeakers
Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking and Visual Checks
AC Power Requirements
Every Tannoy VXP product is carefully tested and inspected before
being packaged and leaving the factory. After unpacking your
loudspeaker, please inspect for any exterior physical damage,
and save the carton and any relevant packaging materials in case
the loudspeaker again requires packing and shipping. In the event
that damage has been sustained in transit, please notify your
dealer immediately.
VXP products are equipped with Neutrik powerCON mains
connectors which mate with the Neutrik NAC3FCA Cable
connector, providing quick lock with a securing lever at power-in.
This AC mains connector is supplied with each VXP product.
The IDEAA™ module in VXP loudspeakers has a universal power
supply. It will operate on any AC mains supply from 70 V to 265 V
(+/- 10%) at 50 or 60 Hz, although with reduced power output
capability at the low voltage extremes. This allows continued
operation even when using long, thin power cables, or when
powered from portable generators that are unable to maintain full
nominal voltage.
Rear Interface Panel
XLR FEMALE AUDIO INPUT - This is a lockable XLR line input
socket for connection to the audio source. Fully balanced: pin 2 hot
(+), pin 3 cold (+), & pin 1 ground.
Auto and Manual Power Modes
XLR MALE AUDIO LINK - This is a lockable XLR line output socket
to link additional speakers. Fully balanced: pin 2 hot (+), pin 3 cold
(+), & pin 1 ground.
VXP loudspeakers offer two modes for power on/off.
POWER MODE SWITCH (top) – Selects AUTO or MANUAL power
on/off mode.
AUTO mode – This is the default mode as delivered. AUTO engages
the auto-power-down (APD) feature which puts the IDEAA™ module
in STANDBY if no input signal is detected for a period of 20 minutes.
The auto-power-on (APO) turns the module on in less than 2
seconds after a signal is present at the input.
HPF MODE SWITCH – Inserts or removes 90 Hz high pass filter.
LEVEL CONTROL – Recessed potentiometer for adjustment of
speaker volume.
MANUAL mode – The power mode may be switched to MANUAL
to disable the auto-power-down and auto-power-on functions. This
allows use of an external power sequencer or manual control.
LED INDICATORS – Top to bottom:
Limit protect indicates activity of built-in speaker protection limiter.
Signal indicates when audio signal is present at the input.
Power state indicates that AC line power is present at the AC mains
connector, and that the power switch is turned on.
Cooling
ROCKER POWER SWITCH - Supplies AC power on to the unit
(100V - 240V)
Do not install this equipment in an enclosed space. Do not limit free
ventilation and movement of air around the back panel. Ensure that
there is at least 100mm (4”) of space around all sides of the product for
ventilation. VXP products do not have cooling fans; the highly efficient
switch mode power supply and proprietary Class D output stage have
low current draw and therefore require only the convection cooling
provided by the rear panel heat sink.
AC MAINS CONNECTOR - Neutrik powerCON mains connector
(mating connector supplied)
System Configuration
All loudspeakers in the VXP range are integrated designs which include
system specific EQ and protection circuitry, without the need for external
amplification. For room equalization, delay and other commissioning or
setup functions, we recommend you use a Vnet SC1 or TDX1 Digital
Controller. Please refer to the full VXP Series manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Functions
Gain Structure and Limiting
Limit LED - When illuminated this indicates that the system is
approaching clipping. An occasional flicker of the red LED on the
loudest peaks is acceptable. If this LED remains red for more than
the duration of brief dynamic peaks, or lights continuously then the
system is being overdriven. If the red LED illuminates excessively:
The VXP gain structure is designed to allow a low-level source device
to drive the loudspeaker to full output. Maximum specified SPL will
be achieved with a 4 dBu input signal. There is sufficient headroom
in the signal path to accommodate input levels of 10 or even 20 dBu,
with high quality compression engaged as needed to maintain sonic
integrity without clipping.
• Reduce the input level (see interface panel)
• Reduce the output level of the mixer, or other source to the
speaker.
Equalisation
Signal LED – The Green LED indicates that a useable signal is
present at the input.
The VXP loudspeaker requires no equalisation or correction to
overcome system limitations; equalisation is necessary only to
compensate for difficult acoustic environments.
Power LED – When AC mains is connected to the speaker and the
power switch is turned on, the blue lower LED will illuminate.
Audio Connections
Rigging and Safety Procedures
The signal input & link connectors are fully balanced. When
connecting a balanced signal be sure to wire to the following
standard:
The installation of Tannoy Professional loudspeakers using the
dedicated hardware should carried out only by fully qualified
installers, in accordance with all the required safety codes and
standards that are applied at the place of installation.
SIGNAL
Hot (+)
Cold (-)
XLR CONNECTOR
Pin 2
Pin 3
Pin 1
WARNING: As the legal requirements for flying change from country
to country, please consult your local safety standards office before
installing any product. We also recommend that you thoroughly
check any laws and bylaws prior to installation. For more detailed
information on rigging hardware and safety procedures, please
consult the full VX Series and VXP Series Hardware Manual available
Shield (GND)
In a standard balanced interconnection there are two signal
conductors and a shield. The shield is normally referenced to
ground at one or both ends. Many times the shield is lifted at one
end, usually at the input to eliminate “ground loops” or noise. This
should be done only as a last resort; although it will reduce hum,
the shields can act as radio antennas and pick up radio frequency
interference from the environment.
Multiple enclosures may be driven from a single audio source; simply
plug the signal source output into the first XLR input socket, and
patch that speaker’s XLR link to the next speaker’s XLR input socket.
Tannoy (Direct UK)
TCGI (ROW sales)
TCGA (Americas sales)
Tannoy Middle East
T: +44 (0) 1236 420199
T: +46 8742 7000
T: +1 (519) 745 1158
T: +97 1 (04) 4401208
E: enquiries@tannoy.com
E: enquiries@tannoy.com
tannoy.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|