CMS
C E I L I N G M O N I T O R S Y S T E M S
I N S T A L L A T I O N M A N U A L
CMS801 DC BM
CMS801 DC PI
CMS801 sub BM
CMS801 sub PI
CMS801 PI back can
Tannoy has a policy of continuous improvement and this specification sheet provides the latest information at the time of printing.
All specifications may be subject to further change. Please contact the Tannoy website for the latest information.
CMS
CMS801 TEMPLATE HOLE CUTOUT SIZE: 295mm (11.61”)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. PRODUCT FEATURE IDENTIFICATION:
5. ACCESSORIES:
Each product is supplied with the following accessories as standard:
Conduit/Cable Clamp
Euro Type Connector
Mounting Wings
Tuning Port
C-Ring
Tile bridge kit
Screws for
mounting wings
Note: A tile bridge kit
must always be used
when installing into
suspended ceiling tiles
Rotary Switch
Fig 1.1: The blind-mount (BM) models come with a pre-fitted back can
Grille
Cut-out template
Screws for
mounting wings
Tuning Port
Euro Type Connector
Rotary Switch
Paint Mask
Fig 1.2: A pre-install (PI) model shown without optional pre-install back can
Euro Type Plug
Euro Type Connector
Optional accessories:
Conduit Knock-out points
Plaster (Mud)
Ring
60W Transformer
Fig 1.3: Optional pre-install (PI) back can for PI models
NOTE: for use with CMS801 PI
model in distributed lines without
back-cans.
Note that the CMS801 PI model’s transformer is pre-attached to the CMS801 PI back can for easy install.
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 MECHANICAL INSTALLATION GUIDE FOR SUSPENDED CEILINGS
5.2 MECHANICAL INSTALLATION GUIDE FOR SHEET-ROCK (PLASTER BOARD) CEILINGS
Remove the ceiling tile from its frame and place it on a flat surface. Mark the
cut-out area on the ceiling tile by tracing around the template provided.
Mark the cut-out area on the ceiling by tracing around the template provided.
1
1
Cut out the hole in the ceiling using a circular saw or pad saw, then slide the
C-ring into the ceiling, aligning it over the cut-out hole).
Cut out the hole in the ceiling tile using a circular saw or pad saw.
2
2
Place the C-ring and tile-bridge on top of the ceiling panel, aligning the C-ring over the
hole, and screw the C-ring to the tile bridge using the fixings provided.
Go to section 6 for wiring and set-up instructions then return to point 4 below.
3
3
Slide the speaker assembly through the hole and turn the screws to extend the mounting
wings. Tighten the screws until a firm grip is achieved.
4
If using a power driver, Tannoy recommends a torque setting of 1.5Nm.
DO NOT OVERTIGHTEN!
Slide the speaker assembly through the hole and turn the screws on the front of the
4
speaker to extend the mounting wings. Tighten the screws until a firm grip is achieved.
If using a power driver, Tannoy recommends a torque setting of 1.5Nm.
DO NOT OVERTIGHTEN!
Insert grille by pushing it onto the speaker.
5
Slide the tile panel back into the suspended ceiling. The tile bridge ends will catch over
the railings, supporting the weight of the speaker.
5
Go to section 6 for instructions on wiring and set-up instructions.
7
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 MECHANICAL INSTALLATION INSTRUCTIONS FOR OPTIONAL PLASTER RING:
5.4 INSTRUCTIONS FOR OPTIONAL PRE-INSTALLATION BACK CAN (PI MODELS ONLY):
An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly
constructed, non-suspended ceilings.
AN OPTIONAL PRE-INSTALL BACK CAN IS AVAILABLE FOR ALL PI (PRE-INSTALL) MODELS. THIS BACK CAN IS DESIGNED TO
BE PRE-INSTALLED INTO NEWLY CONSTRUCTED, NON-SUSPENDED CEILINGS.
Note that the CMS801 PI model’s transformer is pre-attached to CMS801 PI back can for easy install.
Nail or screw the plaster ring to the joists.
1
Attach the back can to the installed conduit This can be attached in two ways:
1
a. You can use the clamp at the back of the pre-install
Conduit
back can. The product will accept a squeeze connector
Conduit Squeeze
with a thread size of up to 22mm: To remove the cable
Connector
clamp, simply unscrew the threaded washer (under the
wiring cover) which holds the cable clamp in place and
replace it with a conduit squeeze connector.
Lay the speaker wiring to where the speaker will be fitted and complete the
plastering work on the ceiling.
2
b. You can use any of the three knock-out points at the
sides of the PI back can (19mm, 22mm or 28mm diameter):
Cut out the hole in the ceiling using a circular saw or pad saw.
3
Lay the speaker wiring to where the speaker will be fitted and complete the
plastering work on the ceiling.
2
Go to section 6 for instructions on wiring then return to point 5 below.
4
Cut out the hole in the ceiling using a circular saw or pad saw
3
Slide the speaker assembly through the hole and turn the screws to extend the mounting
wings. Tighten the screws until a firm grip is achieved.
5
If using a power driver, Tannoy recommends a torque setting of 1.5Nm.
DO NOT OVERTIGHTEN!
Go to section 6 for instructions on wiring and setting up then return to point 5 below.
4
Slide the speaker assembly through the hole and turn the screws to extend
the mounting wings. Tighten the screws until a firm grip is achieved.
5
Insert grille by pushing it onto the speaker.
6
If using a power driver, Tannoy recommends a torque setting of 1.5Nm.
DO NOT OVERTIGHTEN!
9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. WIRING AND SETTING UP:
7.1 CMS801 DC BM DIMENSIONS:
TEMPLATE HOLE CUTOUT SIZE: 295mm
Open the wiring cover at the back of the speaker can to access the Euro type connector
plug and socket.
1
327.8
[12.90"]
286.4
[11.27"]
310.5
[12.22"]
For connection to an amplifier, use pins 1 and 2:
2
5.0
[0.20"]
325.0
[12.80"]
•
•
Pin 1 is positive
Pin 2 is negative
For connection to additional speakers in a distributed line,
pins 3 and 4 are in parallel where:
7.2 CMS801 DC PI DIMENSIONS:
•
•
Pin 3 is negative
Pin 4 is positive
TEMPLATE HOLE CUTOUT SIZE: 295mm
Close the wiring cover and tighten both screws on the cable clamp. Use the rotary
switch located on the front of the unit to select whether you wish to use the speaker in
a low-impedance or distributed-line application.
3
286.4
[11.27"]
118.7
THE SPEAKER IS SUPPLIED IN LOW IMPEDANCE MODE. NEVER CONNECT THE
SPEAKER TO A 70/100 VOLT AMPLIFIER WHILE IT IS SET FOR LOW IMPEDANCE.
[4.67"]
5.0
[0.20"]
All CMS801 models use a 60W transformer. When using distributed-line systems, the
transformer can be tapped at 60W, 30W and 15W, with an additional 7.5W tapping for
70.7V line systems.
325.0
[12.80"]
7.3 CMS801 sub BM DIMENSIONS:
TEMPLATE HOLE CUTOUT SIZE: 295mm
286.4
[11.27"]
327.8
[12.90"]
310.5
[12.22"]
325.0
[12.80"]
18.5
[0.73"]
11
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7.4 CMS801 sub PI DIMENSIONS:
8.1 TECHNICAL SPECIFICATIONS:
MODEL
System
CMS801 DC
TEMPLATE HOLE CUTOUT SIZE: 295mm
Frequency response (-3dB) (1)
BM back can
47Hz - 30kHz
40Hz - 35kHz
41Hz - 35kHz
Enclosure
Back can
Zinc plated steel
Reflex loaded UL 94V-0 rated ABS
Steel, with weather resistant coating
Baffle
Grille
Frequency range (-10dB) (1)
BM back can
Safety Features
Clamping Design
Safety ring located at rear of enclosure
for load bearing safety bond
Frequency range (-10dB) (1)
PI back can
security toggle clamp
117.5
[4.63"]
System sensitivity (1W @1m) (2)
Nominal coverage angle
Coverage angle (1kHz to 6kHz)
Directivity factor (Q)
92dB (1W = 2.83V for 8 Ohms)
90 degrees concal
286.4
[11.27"]
Backcan Options
Blind Mount (BM)
Pre Install (PI)
Complete with fixed back can
Separate back can for pre installation
18.5
[0.73"]
100 degrees conical
Cable Entry Options
Conduit Knockouts
Cable clamp & squeeze connector for
conduit up to 22mm
5.5 averaged 1kHz to 6kHz
7.2 averaged 1kHz to 6kHz
Directivity index (DI)
3 sets of horizontal positions
19/22/28mm 0.75/0.87/1.1"
325.0
[12.80"]
Rated maximum SPL
With THP60
112dB (average)
118dB (peak)
110 (average)
Connectors
Removable locking connector with screw
UL-1480, UL-2043, CE
295mm (11.61")
Safety agency ratings (pending)
BM hole cutout diameter
PI hole cutout diameter
Dimensions
Power handling
Average
90W
180W
360W
Programme
Peak
295mm (11.61")
Recommended amplifier power
Nominal impedance
180W @ 8 Ohms
8 Ohms
7.3 CMS801 PI BACK CAN DIMENSIONS:
Bezel diameter
325mm (12.80")
TEMPLATE HOLE CUTOUT SIZE: 295mm
Transformer taps (via front rorary switch)
Front of ceiling to
rear of back can (BM)
310.5mm (12.22")
70V
60W/30W/15W/7.5W/OFF
& Low impedance operation
60W/30W/15W/OFF
168.5
[6.63"]
100V
Front of ceiling to
top of safety loop (BM)
327.8mm (12.90")
151.2mm (5.95")
168.5mm (6.63")
123.7mm (4.87")
& Low impedance operation
Distortion
10% full power (8.49V)
250Hz
Back of ceiling surface to
rear of back can (PI)
2nd Harmonic
0.65%
3rd Harmonic
0.39%
1kHz
10kHz
1.36%
0.29%
Back of ceiling surface to
top of safety loop (PI)
1%
0.03%
1% full power (2.68V)
250Hz
1kHz
2nd Harmonic
0.20%
3rd Harmonic
0.43%
Front of ceiling to rear of
bass ports (no back can) PI
0.49%
0.28%
291.4
[11.47"]
397.0
[15.63"]
365.0
[14.37"]
10kHz
0.42%
0.03%
Net Weight (ea)
CMS801 BM
CMS801 PI
6.3kg
3.0kg
4.3kg
Crossover
2kHz - 2nd order LF,
2nd order order HF
PI back can
(with dynamic HF protection)
Shipping Weight
CMS801BM (pair)
CMS801PI (pair)
PI back can (single)
19.0kg
11.2kg
5.7kg
Transducers
Low frequency
200mm (8.00") Dual Concentric™
constant directivity driver with multi
fibre paper pulp cone
8.8
151.2
Included Accessories
C Ring, tile bridge, paint mask,
cutout template, grille
[0.35"]
[5.95"]
High frequency
Notes:
25mm (1.00") titanium dome
with neodymium magnet system
Optional Accessories
Plaster (Mud) Ring, line transformer for PI
product installs without back can
(1) Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber
(2) Unweighted pink noise input, measured at 1m on axis.
(3) Long term power handling capacity as defined in EIA - 426B test
13
12
Download from Www.Somanuals.com. All Manuals Search And Download.
8.2 TECHNICAL SPECIFICATIONS:
9. PAINTING
System
CMS801 sub
Transducer
Physical
If desired, the grille and baffle panel may be painted to match the surrounding décor.
Painting the baffle:
1x 200mm (8.00") long throw woofer with
multi fibre paper pulp cone
Frequency response (-3dB) (1)
Frequency range (-10dB) (1)
System sensitivity (1W @1m) (2)
Crossover
58Hz - 160Hz
42Hz - 300Hz
Carefully mask off the driver assembly using the paint-mask provided to ensure that the paint does not come into
contact with the cone and roll surround.
Apply several thin coats of paint – this will provide a better finish than one overly thick coat.
Enclosure
Back can
Baffle
92dB (1W = 2.45V for 8 Ohms)
Zinc plated steel
Reflex loaded UL 94V-0 rated ABS
Steel, with weather resistant coating
Integral 2nd order passive,
160 Hz
Grille
Painting the grille:
Safety features
Safety ring located at rear of enclosure
for load bearing safety bond
Carefully remove the acoustically transparent foam from the reverse side of the grille.
Paint the grille and then replace the foam - several thin coats of paint will provide a better finish than one
overly thick coat.
Rated maximum SPL (2)
112dB (average)
118dB (peak)
110dB (average)
Clamping design
Security toggle clamp
With THP60
Re-bond the foam to the grille over the entire area using a light spray-adhesive to avoid audible resonances.
Back can options
Blind Mount (BM)
Pre Install (PI)
Power handling (3)
Average
Programme
Peak
Complete with fixed back can
Separate back can for Pre Installation
100W
200W
400W
10. WARRANTY
Cable entry options
Conduit knockouts
Connectors
Cable clamp & squeeze connector for
conduit up to 22mm
No maintenance of the CMS loudspeaker is necessary.
3 Sets of horizontal positions
19 / 22 / 28mm (0.75 / 0.87 / 1.1")
Recommended amplifier power
Nominal Impedance
200W @ 8 Ohms
8 Ohms
All Tannoy professional loudspeaker products are covered by a 5 year warranty from the date of manufacture
subject to the absence of misuse, overload or accidental damage. Claims will not be considered if the serial
number has been altered or removed. Work under warranty should only be carried out by a Tannoy Professional
dealer or service agent. This warranty in no way affects your statutory rights. For further information please
contact your dealer or distributor in your country. If you cannot locate your distributor please contact Customer
Services, Tannoy Ltd at the address given below.
Removable locking connector with screw
terminals with "loop through" facility
Transformer taps
(via front rotary switch)
70V
Safety agency ratings (pending)
BM hole cutout diameter
PI hole cutout diameter
UL-1480, UL-2043, CE
295mm (11.61")
60W / 30W / 15W / 7.5W / OFF
& Low Impedance operation
60W / 30W / 15W / OFF
295mm (11.61")
100V
& Low Impedance operation
Dimensions
Bezel diameter
325mm (12.80")
310.5mm (12.22")
327.8mm (12.90")
151.2mm (5.95")
168.5mm (6.63")
123.7mm (4.87")
Distortion
10% Full Power (7.75V)
70Hz
100Hz
Front of ceiling to
rear of back can (BM)
2nd Harmonic
1.22%
0.38%
3rd Harmonic
1.90%
0.49%
Customer Services
Tannoy Ltd.
Rosehall Industrial Estate
Coatbridge
Strathclyde
ML5 4TF
Front of ceiling to
top of safety loop (BM)
1% Full Power (2.45V)
70Hz
100Hz
2nd Harmonic
0.91%
0.04%
3rd Harmonic
1.28%
0.44%
Back of ceiling surface to
Rear of backcan (PI)
Back of ceiling surface to
top of safety loop (PI)
Front of ceiling to rear of
bass ports (no back can) (PI)
Scotland
Notes
(1) Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber
(2) Unweighted pink noise input, measured in an IEC baffle in an Anechoic Chamber.
Net weight (ea)
CMS801 SUB BM
CMS801 SUB PI
PI Back can
Tel: 01236 420199
(National)
6.3kg (13.89lbs)
3.2kg (7.05lbs)
4.0kg (8.8lbs)
If the loudspeaker is placed in the ceiling near a corner ( / 2) an increase of 6dB
in sensitivity and maximum SPL can be realised.
+44 1236 420199 (International)
(3) Long term power handling capacity as defined in EIA - 426B test
A full range of measurements, performance data, and Ease™ Data can be
Fax: 01236 428230
(National)
+44 1236 428230 (International)
E-mail: [email protected]
Included accessories
C Ring, tile bridge, paint mask,
cutout template, grille
Optional accessories
Plaster (Mud) Ring
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the published
specifications, which Tannoy reserves the right to alter without prior notice. Please
verify the latest specifications when dealing with critical applications
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
Ordering information
Our policy commits us to incorporating improvements to our products through continuous research
and development. Please confirm current specifications for critical applications with your supplier.
PART NUMBER
MODEL NAME
BAFFLE / GRILLE
PACKED
QUANTITY
PACKED WEIGHT
kg (lbs)
COLOUR
8001 4730
8001 4740
CMS801 SUB BM
CMS801 SUB PI
WHITE
WHITE
2
2
19.0 (41.89)
11.5 (23.35)
15
14
Download from Www.Somanuals.com. All Manuals Search And Download.
11. DECLARATION OF CONFORMITY:
NOTES
The following apparatus is manufactured in China for Tannoy
Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF
and conform(s) to the protection requirements of the European
Electromagnetic Compatibility Standards and Directives relevant
to Domestic Electrical Equipment. The apparatus is designed
and constructed such that electromagnetic disturbances generated
do not exceed levels allowing radio and telecommunications
equipment and other apparatus to operate as intended, and, the
apparatus has an adequate level of intrinsic immunity to
electromagnetic disturbance to enable operation as specified
and intended.
Details of the Apparatus:
Model Numbers:
Tannoy Contractor Loudspeaker
CMS801 DC BM
CMS801 DC PI
CMS801 sub BM
CMS801 sub PI
CMS801 PI back-can
Applicable Standards:
EN 50103-1 Emission
EN 50103-1 Immunity
Electrical Safety:
Signed:
EN 60065
Position: Engineering Director - Professional Products
Tannoy Professional
Date: 26/05/2007
For Tannoy Ltd
17
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
NOTES
19
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|