OWNER’S
MANUAL
SYMPHONIC
COLOR TV/DVD
RSMSD520FE
(20 inch)
SUPPLIED ACCESSORIES
Remote Control Unit
Batteries
Owner’s Manual
Owner's Manual
INSTRUCCIONES
EN ESPAÑOL INCLUIDAS.
NE224UD
2 AA Batteries
0EMN02493
As an ENERGY STAR®
Partner, our company has
determined that this product meets
the ENERGY STAR® guidelines for
energy efficiency. ENERGY STAR®
If you need additional assistance for set-up or operating after
reading owner’s manual, please call TOLL FREE :
1-800-242-7158
is a U.S. registered mark.
Please read before using this equipment
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying par-
ticular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
19.Damage Requiring Service-Unplug this TV/DVD from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/DVD.
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/DVD, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
c. If the TV/DVD has been exposed to rain or water.
d. If the TV/DVD does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the TV/DVD to its normal operation.
e. If the TV/DVD has been dropped or damaged in any way.
f. When the TV/DVD exhibits a distinct change in perfor-
mance-this indicates a need for service.
14.Lightning-For added protection for this TV/DVD receiver
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the TV/DVD due to lightning and
power-line surges.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
21.Safety Check-Upon completion of any service or repairs to
this TV/DVD, ask the service technician to perform routine
safety checks to determine that the TV/DVD is in proper
operating condition.
22.Heat-This TV/DVD product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/DVD through openings as they may touch dan-
gerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on
the TV/DVD.
18.Servicing-Do not attempt to service this TV/DVD yourself
as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to qualified
service personnel.
EN
–
–
3
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
LASER SAFETY
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public perfor-
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to ser-
vice this device, due to possible eye injury.
mance and lending of discs are prohibited.
This product incorporates copyright protection tech-
nology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing
uses only unless otherwise authorized by
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est con-
forme à la norme NMB-003 du Canada.
RADIO-TV INTERFERENCE
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable
and can be reused. Please dispose of any materials
in accordance with your local recycling regula-
tions.
Batteries should never be thrown away or inciner-
ated but disposed of in accordance with your local
regulations concerning chemical wastes.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial
number as yours. You should record the number and other vital information here and retain this book as a per-
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
EN
–
–
4
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION
For safe operation and satisfactory performance of
your TV/DVD, keep the following in mind when
selecting a place for its installation:
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some head-
ings and notes in this manual, with the following
meanings
Shield it from direct sunlight and keep it away from
sources of intense heat.
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top or bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
TV
•
: Description refers to TV operation (in the TV mode).
•
•
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
CD
: Description refers to playback of audio CDs
(in the DVD mode).
•
MP3
•
: Description refers to playback of MP3 discs
(in the DVD mode).
Do not place the TV/DVD near strong magnetic fields.
Avoid moving TV/DVD to locations where temper-
ature differences are extreme.
•
•
QUICK
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
•
•
If by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
•
Do not put your fingers or objects into the
TV/DVD disc loading tray.
•
Do not place anything directly on top of the unit.
•
WARNING
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a TV/DVD
which has moisture, it may damage the DVD and
TV/DVD. Therefore when the condensation occurs
inside the unit, turn POWER on and allow at least 2
hours for the unit to dry out.
EN
–
–
5
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2
C SEARCH FUNCTION . . . . . . . . . . . . . . . . . .22
TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . .22
TITLE / CHAPTER SEARCH . . . . . . . . . . . . .22
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .22
MARKER SETUP SCREEN . . . . . . . . . . . . . .22
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF ELECTRICAL
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .5
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS MANUAL . . . . . . .5
C SPECIAL PLAYBACK FUNCTION . . . . . . . .23
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .23
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .23
C TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
C PLAYING A MP3 DISC . . . . . . . . . . . . . . . . . .24
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . .24
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .24
RANDOM PLAYBACK . . . . . . . . . . . . . . . . .24
C
OPERATING CONTROLS AND FUNCTIONS . . .8
INSTALLING THE BATTERIES . . . . . . . . . . .9
C PREPARATION FOR USE . . . . . . . . . . . . . . .10
ANTENNA/CABLE CONNECTIONS . . . . . . .10
CONNECTING TO EXTERNAL INPUT JACKS .11
C CHANGING THE SETTINGS . . . . . . . . . . . .25
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . .25
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . .25
STEREO SOUND MODE . . . . . . . . . . . . . . . .25
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . .25
BLACK LEVEL SETTING . . . . . . . . . . . . . . .25
VIRTUAL SURROUND . . . . . . . . . . . . . . . . .25
CONNECTING TO AN AMPLIFIER
EQUIPPED WITH DIGITAL INPUT JACKS,
MD DECK OR DAT DECK (for DVD only) . .11
CONNECTING TO A DOLBY DIGITAL
DECODER (for DVD) . . . . . . . . . . . . . . . . . . .12
TV SECTION
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .13
SELECTING THE LANGUAGE . . . . . . . . . . .13
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . .13
DELETING (OR ADDING) CHANNEL(S) . . .14
C THE ON-SCREEN INFORMATION . . . . . . .26
C CHANGING THE DVD SETUP ITEMS . . . .27
LANGUAGE SETTING . . . . . . . . . . . . . . . . .27
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . .28
AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .28
PARENTAL CONTROL . . . . . . . . . . . . . . . . .29
INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . .29
C TROUBLESHOOTING GUIDE . . . . . . . . . . .30
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15
WATCHING A TV PROGRAM . . . . . . . . . . . .15
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .16
CLOSED CAPTION SYSTEM . . . . . . . . . . . .16
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .17
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .32
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .32
DVD SECTION
C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .19
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .33
C ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .19
DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .19
C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .20
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . .20
GENERAL FEATURES . . . . . . . . . . . . . . . . . .20
DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . .20
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . .20
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
STEP BY STEP PLAYBACK . . . . . . . . . . . . .21
FAST FORWARD/REVERSE SEARCH . . . . .21
SLOW FORWARD / SLOW REVERSE . . . . .21
EN
–
–
6
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
TV Mode
DVD Mode
¡Dolby Digital sound
181 channel capability PLL frequency synthesiz-
er tuner with direct station call
(A converter may be necessary to view scrambled cable
channels.)
•
This TV/DVD can handle Dolby Digital surround sound
having 5.1 channels when connected to a Dolby Digital
decoder.
¡Still/fast/slow/step playback
Various playback modes are available including still pic-
tures, fast forward/reverse, slow motion and step frames.
Infrared remote control
Trilingual on screen menu display selectable in
English, Spanish, or French
•
•
¡Random playback for audio CD and MP3
This TV/DVD can shuffle the order of tracks to play them
in random order.
¡Sleep Timer
The Sleep Timer function enables you to shut off the power
without pressing POWER after a desired time period.
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in any
desired order.
¡Closed Caption Decoder
You may view specially labeled (cc) TV programs,
movies, news, etc. with either a dialogue caption or text
display added to the program.
¡DVD menus in a desired language
You can display DVD menus in a desired language, if
available on a DVD.
¡Auto Shut Off Function
If there is no air signal input from the antenna terminal and
no operation for 15 minutes, the TV/DVD will turn itself
off automatically.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input
from the TV/DVD for five minutes in the stop mode.
When the screen saver program is activated for 15 min-
utes, the power is automatically turned off.
¡V-CHIP
Enables parents to prevent their children from watching
inappropriate material on TV.
¡Subtitles in a desired language
You can select a desired language for the display subtitles,
if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc contains
sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound mode,
if different languages and modes are available on a disc.
¡Parental lock
You can set the control level to limit playback of discs
which may not be suitable for children.
¡Automatic detection of discs
This TV/DVD automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡On-screen display
Information about the current operation can be displayed
on a TV screen, allowing you to confirm the currently
active functions (such as program playback), on the TV
screen using the remote control.
¡Search
Chapter search / Title search / Track search / Time search
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which the
play was stopped.
¡Virtual Surround
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
EN
–
–
7
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING CONTROLS AND FUNCTIONS
[Fig. 1]
TV/DVD FRONT PANEL
VIDEO
AUDIO
POWER
VOLUME
CHANNEL
STOP
PREV
PLAY
NEXT PAUSE OPEN/CLOSE HEADPHONE
L
R
–SEARCH–
1
2
3
4
5
6
7 8 9 10111213 14
7. Remote Sensor Window
[Fig. 2]
REMOTE CONTROL
8. STOP Button [page 20]
Stops operation of the disc.
9.PREV (SKIP) H Button [page 21]
Plays back from the beginning of the current
chapter or track.
SEARCH (REV) E Button (Front Panel)
[page 21]
During playback or in the pause mode, press and
hold button down for a few seconds to change
reverse playback speed.
OPEN/
CLOSE
POWER PICTURE SELECT
4
13
34
36
1
4
2
5
8
0
3
6
CH.
6
16
7
SLEEP
9
+100
10. PLAY Button [page 20]
VOL.
5
Starts playback of the disc contents.
Press to change to DVD mode when TV mode.
+10
17
SKIP
V.SURR
MUTE
9
11
10
35
19
18
11. NEXT (SKIP) G Button [page 21]
Plays back from the beginning of the next chapter
or track.
PLAY
STOP
REV
FWD
SEARCH (FWD) D Button (Front Panel)
[page 21]
8
DISC
PAUSE SLOW
DISPLAY
MENU
12
23
33
During playback or in the pause mode, press and
hold button down for a few seconds to change for-
ward playback speed.
32
31
30
ENTER
SETUP
TITLE
RETURN
20
21
22
12. PAUSE Button [page 21]
CLEAR SEARCH MODE REPEAT
A-B
Pauses the current disc operation.
29
13. OPEN/CLOSE Button [page 20]
Press to insert discs into or remove them from the
tray.
14. HEADPHONE Jack
To connect headphone (not supplied) for personal
listening.
15. MODE Button [pages 23-25]
Activates program playback or random playback
mode when playing CDs or MP3.
AUDIO SUBTITLE ANGLE
MODE
15
24
25
28
27
26
1. Disc loading tray
2. VIDEO input Jack [page 11]
Connect to the video output jack of a video camera
or VCR.
16. Number Buttons
3. AUDIO L/R input Jacks [page 11]
TV Mode: [page 15]
Connect to the audio output jacks of a video camera
or VCR.
Press two digits to directly access the desired channel.
Remember to press 0 before a single digit channel.
+100 Button
4. POWER Button [page 13]
Press to turn the power on and off.
Press to select cable channels which are higher than 99.
DVD Mode: [page 22]
5. VOLUME K/L (VOL.
m/n) Buttons
Press to control the volume level for the DVD and TV.
Press to enter the desired number.
+10 Button
6. CHANNEL K/L (CH. K/L) Buttons [page 14]
Press to select memorized channel.
Press to change to TV mode when DVD mode.
Press to enter the desired numbers which are greater
than 9.
EN
–
–
8
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
[Fig. 3]
TV/DVD REAR VIEW
ANT.
COAXIAL
37
38 39
32. Arrow Buttons
17. SLEEP Button [page 16]
TV Mode: [page 13]
Press SLEEP to display the sleep timer and start the
function. The shut off time can be determined by the
number of times you press this button. (0, 30, 60, 90
or 120 minutes)
Press to select a setting mode from the menu on the
TV screen.
Press to select or adjust from a particular menu.
DVD Mode: [page 20]
18. REV h Button [page 21]
Use when making settings while watching the dis-
play on a TV screen.
Press to view the DVD picture in fast reverse
motion. Press PAUSE, then press this button to begin
slow motion playback. Press this button repeatedly
to change the reverse speed of slow motion.
33. DISC MENU Button [page 20]
Displays the menus in the DVD.
FWD g Button [page 21]
34. SELECT Button [page 20]
Press to change to TV mode, external input mode or
DVD mode.
Press to fast forward the Disc. Press PAUSE, then
press this button to begin slow motion playback.
Press this button repeatedly to change the forward
speed of slow motion.
NOTE: When you select the DVD mode by this
button, press PLAY or OPEN/CLOSE first.
Otherwise, the DVD features are not operated.
19. V.SURR (VIRTUAL SURROUND) Button
[page 25]
Press to set virtual surround on/off.
35. MUTE Button
20. SETUP Button [pages 13,27-29]
Press to enter or exit the TV menu or DVD setup
mode.
Press MUTE to turn off the sound portion of the TV
program. (Volume level display turns LIGHT RED
from LIGHT BLUE.) Press MUTE again or press
21. TITLE Button [page 20]
VOL.
m
or
n
to restore sound.
Displays the title menu.
36. PICTURE Button [page 15]
22. CLEAR Button [pages 22-24]
Press to enter picture adjustment mode.
Resets a setting.
37. Power cord
23. DISPLAY Button
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect to
a standard AC outlet.
TV Mode:
Press to display the channel number on the screen.
If you press it again, the channel number will disap-
pear.
38. COAXIAL digital audio out Jack
(DVD Audio Only) [pages 11, 12]
Connect to the digital input of an external amplifier
or decoder.
DVD Mode: [page 26]
Displays the current status on the TV screen for
checking purposes.
24. SEARCH MODE Button [page 22]
39. ANT. in Jack
Press to locate a desired point.
Connect to an antenna, cable system or satellite sys-
tem.
25. AUDIO Button [page 25]
Press to select a desired audio language or sound
mode.
26. SUBTITLE Button [page 25]
Press to select a desired subtitle language.
INSTALLING THE BATTERIES
27. REPEAT Button [page 23]
Repeats playback of the current disc, title, chapter,
group or track.
1)Open the battery compartment cover by pressing the
cover on the remote unit in the direction of the arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
28. ANGLE Button [page 25]
Press to change the camera angle to see the sequence
being played back from a different angle.
29. REPEAT A-B Button [page 23]
Repeats playback of a selected section.
3)Replace the cover.
30. RETURN Button [page 25]
Returns to the previous operation in the DVD setup
mode.
NOTES
31. ENTER Button [pages 13, 20]
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
Press to accept a setting.
EN
–
–
9
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
From Cable System or
Satellite Box or
Cable Box
(Not supplied)
VHF/UHF Antenna
(Not supplied)
OUT
IN
Satellite Dish
VHF Antenna
(Not supplied)
UHF Antenna
(Not supplied)
From
Cable System
ANT.
COAXIAL
VHF/UHF
Combiner
(Not supplied)
or
or
ANT.
or
75-ohm Coaxial
Cable (Not supplied)
Flat twin-lead cable
[Fig. 4]
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
Bent pin
NOTE:
Before plugging the antenna into the ANT. IN jack of the TV/DVD, check that
the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin
into the ANT. IN jack of the TV/DVD.
Cable
Plug
(Needs to be straightened)(Straight pin)
VHF/UHF COMBINED ANTENNA
A VHF UHF 75 ohm combination antenna can be
connected to ANT terminal.
CABLE WITH CONVERTER/DESCRAM-
BLER BOX OR SATELLITE BOX
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown here.
Channel selection must be made with the converter
box or satellite box. This means that channels cannot
be changed using the TV/ DVD Remote Control.
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your TV/DVD without a converter box.
Use the TV/ DVD Remote Control to select channels.
TO VIEW A SCRAMBLED/UNSCRAMBLED
CHANNEL
1.Set the TV/DVD channel selector to the output
channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to view on your Cable Converter
Box or Satellite Box.
EN
–
–
10
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO EXTERNAL INPUT JACKS
When you watch a program recorded on an another
[Front of the TV/DVD]
source (VCR or video camera), use the audio/video
input jacks on the front of the TV/DVD.
Connect the audio/video output
VIDEO
AUDIO
POWER
L
R
To the
[Another source]
audio out-
put jacks
jacks of another source to the
AUDIO L/R and VIDEO jacks of
this TV/DVD. Then press SELECT
until "AUX" appears on the screen.
NOTE:
AUX
VIDEO
AUDIO
Audio/Video
cables
(not supplied)
L
R
When you connect a monaural VCR (another
•
source) to this TV/DVD, connect the Audio output
jack of the monaural VCR (another source) to the
AUDIO L jack of this TV/DVD. The audio will
output in both L and R channel equally.
etc.
To the video
output jack
[Fig. 5]
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL
INPUT JACKS, MD DECK OR DAT DECK (for DVD only)
Use an audio coaxial digital cable available at retail for the audio connections.
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
ANT.
COAXIAL
To COAXIAL DIGITAL
AUDIO INPUT jack
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 6]
NOTES:
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.
Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect set-
tings may generate noise distortion and may also damage the speakers. (See page 28 to set DOLBY
DIGITAL to OFF.)
•
•
•
EN
–
–
11
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this TV/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the TV/DVD out-
puts a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the TV/DVD up
to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-qual-
ity surround sound as enjoyed in movie theaters.
Use audio coaxial digital cables available at retail for the audio connections.
Center
speaker
ANT.
COAXIAL
Front speaker
(left)
Front speaker
(right)
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
Dolby Digital decoder
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
[Fig. 7]
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
(See page 28 to set DOLBY DIGITAL to ON.)
•
•
•
Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup
mode. Playing a TV/DVD using incorrect settings may generate noise distortion and may also damage the
speakers.
•
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
EN
–
–
12
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SECTION
SET UP FOR USE
SELECTING THE LANGUAGE
CHANNEL SET UP
TV
TV
You can program the tuner to scan all the channels
you receive in your area.
1 Plug in the TV/DVD power cord
Plug the TV/DVD power cord into a
standard AC outlet.
NOTE: Channel memory programming is NOT
needed when connected to a cable box or satellite
box. Just select the TV/DVD channel selector to the
output channel of the cable box or satellite box (Ex
CH3), then select the channel to be viewed on the
Cable Box or Satellite Box.
NOTE:
If any digits appear in the corner of
the screen, press POWER without
unplugging the power cord.
•
Make sure ...
Make sure ...
Press POWER to turn on the TV/DVD.
NOTE: This function effects only the language on
•
Press POWER to turn on the TV/DVD.
•
the screen menu and not the audio source.
1 Select “CHANNEL SET UP”
Press SETUP on the remote control.
Press Arrow (K/L) to point to
“CHANNEL SET UP”.
- TV SETUP -
- TV SETUP -
2 Select “LANGUAGE”
B
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Press SETUP on the remote control.
B
Press Arrow (K/L) to point to
Then press ENTER.
“LANGUAGE”.
2 Begin auto ch programming
Press Arrow (K/L) to point to
“AUTO CH PROGRAMMING”.
Then press ENTER.
3 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”
Select “ENGLISH”, “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using ENTER.
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
B
The tuner scans and memorizes all
the active channels in your area.
4 Exit the Language mode
Press SETUP to return to TV mode.
NOTE: If for some reason the menu is in Spanish or
French, press SETUP, press Arrow (K/L) to point to
“IDIOMA [ESPAÑOL]” or “LANGAGE
[FRANÇAIS]”, then press ENTER, then press
SETUP on the remote control.
3 After scanning
The tuner stops on the lowest memorized channel.
•
When AUTO CH PROGRAMMING is activated
where there is no TV signal input, “NO TV SIG-
NALS” will appear on the display after the com-
pletion of the channel scanning.
The TV/DVD may recognize TV channels to be
•
CATV channels by the receiving conditions. In this
case, try auto ch programming again in the fine
receiving conditions.
EN
–
–
13
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
DELETING (OR ADDING)
CHANNEL(S)
TV
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
1 Select “CHANNEL SET UP”
Press SETUP on the remote control.
- TV SETUP -
Press Arrow (K/L) to point to
“CHANNEL SET UP”.
B
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Then press ENTER.
– CHANNEL SET UP –
2 Select “ADD/DELETE CH”
Press Arrow (K/L) to point to
“ADD/DELETE CH”.
B
ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
Press ENTER.
3 Enter the desired channel number
Press Arrow (K/L) until your
desired channel number appears.
(You can also use the number but-
tons or CHANNEL(CH.) K/L to
enter it) (Example: CH8)
08
ADD / DELETE
You must precede single-digit
•
channel numbers with a zero (Example: 02 ... 09).
When selecting cable channels which are higher
than 99, press +100 first, then press the last two
digits. (Example: to select channel 125, first press
+100, then press 2 and 5).
•
4 Delete (or add) it from (into) memory
Press ENTER. The channel number changes to light
red. The channel is deleted from memory.
To delete another channel, repeat steps [3] and [4].
If you press ENTER again, the channel is memo-
rized again.
•
•
Added channel: Light blue.
Deleted channel: Light red.
5 Exit the channel setup mode
Press SETUP to return to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press CHANNEL(CH.) K/L.
EN
–
–
14
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
TV OPERATION
WATCHING A TV PROGRAM
PICTURE CONTROL
TV
TV
1 Turn on the TV/DVD
The TV/DVD’s picture controls – BRIGHT, CON-
TRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a more natural looking image.
Press POWER to turn on the TV/DVD.
2 Select the channel number
Press CHANNEL(CH.) K/L to select your desired
channel number or press the number buttons.
Notes for using the number buttons on the remote
control:
Make sure ...
TV/DVD power must be turned on.
•
You must precede single-digit channel numbers
with a zero (Example: 02 ... 09).
When selecting cable channels which are higher
than 99, press +100 first, then press the last two
digits. (Example: to select channel 125, first press
+100, then press 2 and 5).
•
1 Select “PICTURE CONTROL”
Press PICTURE on the remote control.
•
2 Select item you want to adjust
Press Arrow (K/L) until desired control is displayed.
Remember:
¡If the TV/DVD is connected to a cable box or
satellite box, the TV/DVD must be on CH3 or
CH4, then the channel to be viewed must be select-
ed on the cable box or satellite box.
BRIGHT
CONTRAST
COLOR
BRIGHT
TINT
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
SHARPNESS
3 Adjust sound
Press VOLUME(VOL.) X/Y to
3 Adjust the picture control
Press Arrow (s / B) to adjust to your desired level
adjust the volume.
VOLUME 20
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
within 5 seconds.
NOTE:
NOTE:
If you press CHANNEL(CH.) K/L in the DVD
mode, you can change the TV channels.
•
At step [3], the picture adjustment display will dis-
appear from the TV screen after about 5 seconds
unless you press any buttons, even though you may
not be finished. In this case, repeat from step [1].
•
Even if you turn off the TV/DVD in the DVD
mode, when you turn it on again, it will go into the
TV mode.
Arrow Button
{
Arrow Button
B
to decrease
brightness
to increase
brightness
BRIGHT
DEGAUSSING
Magnetism from nearby appliances and speakers
might affect the color of the TV picture.
to increase
contrast
to decrease
contrast
CONTRAST
If this happens, move this unit away from the appli-
ance. If the color is still not correct, disconnect power
cord from AC outlet then reconnect it after 30 minutes.
to pale
to purple
to soft
to brilliant
to green
COLOR
TINT
to clear
SHAPNESS
If there is a power failure of any kind, the unit will
retain its memory for this feature.
•
EN
–
–
15
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
SLEEP TIMER
If the TV/DVD displays a black
box on the TV screen, this means
that the TV/DVD is set to the
TEXT mode. To clear screen, select
[CAPTION1], [CAPTION2] or
[OFF].
TV
T
he Sleep Timer function enables you to shut off the power
without pressing POWER after a desired time period.
1 Set “SLEEP TIMER”
Make sure ...
Press SLEEP on the remote control.
You may change the sleep time
with pressing SLEEP repeatedly.
TV/DVD power must be turned on.
•
The timer is set up to 120 minutes,
30 minutes each time SLEEP is
pressed.
- TV SETUP -
1 Select “CAPTION”
SLEEP 120 MINUTE
Press SETUP on the remote control.
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Press K or L to point to “CAP-
B
TION”.
To cancel the sleep timer:
Press SLEEP repeatedly until “SLEEP 0 MINUTE”
is displayed.
2 Select your desired caption menu
NOTES:
- TV SETUP -
Press ENTER until your desired
When you disconnect the unit from the AC outlet,
•
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION 1]
caption menu appears.
or if you have a power failure, the sleep time will
be lost.
B
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
To view the time left for sleep timer press SLEEP
once when SLEEP display disappears. After 10
seconds, display will disappear again.
•
3 Exit the caption setting mode
Press SETUP to return to TV mode.
CLOSED CAPTION SYSTEM
TV
You can view specially labeled (cc) TV programs,
movies, news, etc. with either a dialogue caption or
text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using ENTER.
Press SETUP on the remote control to return to TV
mode.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 sec-
onds.
This is also true when MUTE is pressed.
If there is a power failure of any kind, the unit will
retain its memory for this feature.
NOTE:
•
•
Not all programs are broadcast with closed captions.
Your television is designed to provide error free
closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions
errors are listed below:
Automobile ignition noise
Electric motor brush noise
Weak snowy reception on TV screen
Multiplex signal reception displaying picture
•
•
•
•
ghosts or airplane flutter.
EN
–
–
16
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
V-CHIP SET UP
When you select a rating category and turn it
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “TV-Y” to [VIEW], all ratings will
turn to [VIEW] automatically.
•
•
TV
V-CHIP enables parents to prevent their children
from watching inappropriate material on TV.
V-CHIP reads the ratings for programming (except
for news and sports programs, unedited movies on
premium cable channels, and Emergency Broadcast
System signals), then denies access to programming
if the program’s rating meets the limitations you
select. In this case, “PROTECTED PROGRAM by
...” message appears on the TV screen.
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
TV-Y7
TV-G
Appropriate for children seven and older
General Audience
TV-PG
TV-14
Parental Guidance suggested.
Unsuitable for children under 14
To block ratings, follow the steps below.
TV-MA Mature audience only
Programming may be rated by the Motion Picture
•
Association of America (MPAA) or according to
the Television Parental Guidelines. In order to
block any inappropriate programming, set your
limits in both places (MPAA RATING and TV
RATING).
When you select TV-Y7, TV-PG, TV-14 or TV-MA
and you press ENTER, the sub-ratings will appear
on the TV screen.
If you select the rating category (example: TV-PG)
and turn it [BLOCK] or [VIEW], the sub-ratings
(example: V for Violence) will turn [BLOCK] or
[VIEW] automatically.
TV RATING SET UP
You can set the sub-ratings to [BLOCK] or [VIEW]
individually when the rating category is set to
[BLOCK].
Make sure ...
TV/DVD power must be turned on.
•
To set the sub-ratings individually, follow the steps
below.
- TV SETUP -
1 Select “V-CHIP SET UP”
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Press SETUP on the remote control.
B
When you select [TV-Y7]:
•
Press Arrow (K/L) to point to “V-
CHIP SET UP”.
Then press ENTER.
TV–Y7
FV
[BLOCK]
[BLOCK]
Press Arrow (K/L) to select
“FV” (Fantasy Violence).
Then press ENTER to select
[BLOCK] or [VIEW].
B
2 Input Access code
Press the number buttons to enter 4-
digit access code. The default code
is 0000.
ACCESS CODE
When you select [TV-PG], [TV-14] or [TV-MA]:
Press Arrow (K/L) to select
•
•
_
_
_
_
“D”(Suggestive Dialog),
TV–PG
[BLOCK]
B
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
“L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then press
ENTER to select [BLOCK] or [VIEW].
NOTE: When you select [TV-MA], “D” does not
appear on the TV screen.
3 Select “TV RATING”
Press Arrow (K/L) to point to “TV
RATING”.
– V-CHIP SET UP –
B
TV RATING
MPAA RATING
CHANGE CODE
The sub-ratings which set to
B
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
(
)
[VIEW]
Then press ENTER.
[VIEW]
[BLOCK] appears next to the rat-
ing category in the TV RATING
menu.
[BLOCK]
[BLOCK]
[BLOCK]
4 Select your desired item
Press Arrow (K/L) to point to your
desired item.
Then press ENTER to select
[BLOCK] or [VIEW].
B
TV–Y
TV–Y7
TV–G
TV–PG (
TV–14
TV–MA(
[VIEW]
(
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
5 Exit the V-Chip setting mode
Press SETUP on the remote control to return to orig-
inal mode.
)
)
)
(
EN
–
–
17
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
MPAA RATING SET UP
CHANGE ACCESS CODE
Make sure ...
To change access code, follow the steps.
TV/DVD power must be turned on.
•
1 Select “V-CHIP SET UP”
- TV SETUP -
1 Select “V-CHIP SET UP”
Press SETUP on the remote con-
- TV SETUP -
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
trol.
Press SETUP on the remote control.
B
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B
Press Arrow (K/L) to point to “V-
CHIP SET UP”.
Press Arrow (K/L) to point to “V-
CHIP SET UP”.
Then press ENTER.
Then press ENTER.
ACCESS CODE
2 Enter 4-digit access code
Press the number buttons. The
default code is 0000.
2 Enter 4-digit access code
Press the number buttons. The
default code is 0000.
ACCESS CODE
_
_
_
_
_
_
_
_
– V-CHIP SET UP –
3 Select “CHANGE CODE”
Press Arrow (K/L) to point to
“CHANGE CODE".
– V-CHIP SET UP –
3 Select “MPAA RATING”
Press Arrow (K/L) to point to
“MPAA RATING”.
TV RATING
MPAA RATING
CHANGE CODE
TV RATING
MPAA RATING
CHANGE CODE
B
B
Then press ENTER.
Then press ENTER.
4 Enter 4-digit access code
Press the number buttons to enter
your desired access code in the
NEW CODE space. Then enter the
same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
4 Select your desired item
Press Arrow (K/L) to point to your
desired item.
Then press ENTER to select
[BLOCK] or [VIEW].
NEW CODE
_
_
_
_
_
G
[VIEW]
PG
[VIEW]
CONFIRM CODE
PG–13
R
NC–17
X
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
_
_
_
Selection
G
Rating Category Explanations
General Audience
If you enter wrong code, repeat step 4, making
sure you enter the same new code exactly in the
confirm code space.
•
PG
PG-13
R
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompa-
nying parent or adult guardian
No one under 17 admitted
5 Exit the V-Chip setting mode
Press SETUP on the remote control to return to orig-
inal mode.
NC-17
X
Mature audience only
NOTE:
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “G” to [VIEW], all ratings will turn
to [VIEW] automatically.
•
•
If you unplug the power cord or power failure
•
occurs, the changed access code will be lost and
will return to default (0000). Change your access
code again as necessary.
5 Exit the V-Chip setting mode
Press SETUP on the remote control to return to origi-
nal mode.
EN
–
–
18
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this TV/DVD.
[
]
DVD
Data on a DVD is divided into sections called "titles" and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs and these playback con-
ditions take priority over user operations on this
TV/DVD. If a function you selected does not run as
desired, refer to the manual accompanying the disc.
¡
¡
¡
¡
¡
¡
DVD video
DVD+R/RW*
CD-R/RW*
DVD-R/RW*
Audio CD
MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
• Some DVD-R/RW, DVD+R/RW or CD-R/RW discs
made on personal computers or on DVD recorders may
not be played back properly due to the factors such as
scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played
back properly due to the different environment or the
settings of the application you use. We recommend
always to use the standardized, rightly formatted discs.
(Please contact the sales agency for more detail).
Example
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
This TV/DVD conforms to the NTSC color system. You
cannot play discs recorded in other color systems such as
PAL or SECAM.
[
]
AUDIO CD
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
¡Some discs include region codes as shown below.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on TV/DVD with the same
region code.
The following discs cannot be played back on this
TV/DVD.
[
]
MP3
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
¡
DVD with region codes other than 1 or ALL
¡
¡
DVD-ROM
Example
DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
Group 1
Group 2
¡
¡
¡
¡
¡
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
CD-ROM
VSD
CDV (Only plays back the audio part.)
CD-G (Only plays back the sound.)
CD-I (Never play back, otherwise malfunction
may result.)
¡
¡
SACD
Photo CD (Never play back, otherwise malfunc-
tion may result.)
¡
¡
Video CD (Never play back, otherwise malfunc-
tion may result.)
DTS-CD
Any other discs without compatibility indications.
EN
–
–
19
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A DISC
BASIC PLAYBACK
GENERAL FEATURES
DVD-V
CD
MP3
DVD-V
DVD may contain menus to navigate the disc and
access special features. Press appropriate numerical key
or use Arrow (K/L/s/B) to highlight your selection in
the DVD main menu and press ENTER to confirm.
NOTES
¡Select DVD mode by pressing SELECT on the
remote control. Then press PLAY or OPEN/CLOSE
before you operate the DVD functions.
Getting started
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1
Press POWER.
¡The power will turn on.
2
3
Press OPEN/CLOSE to open disc loading
tray.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
Place the chosen disc in the tray, with the
label facing up.
DISC MENU
DVD-V
1
Press DISC MENU on the remote control.
¡The DVD main menu will appear.
4
Press PLAY.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
¡The tray will close automatically and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
PLAY.
If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selec-
tion.
¡When you playback a DVD which features a title
menu, it may appear on the screen. In this case, refer
to “TITLE MENU”.
4
Press Arrow (K/L/s/B) to select an item
and ENTER to confirm selection.
5
Press STOP to stop playback.
TITLE MENU
NOTES
¡When the DVD mode has been switched to the TV
mode, the DVD mode shuts down first and then TV
picture and sound appears in about 4 seconds.
Similarly, when POWER is pressed to turn off in the
DVD mode, this mode shuts down first and then the
TV/DVD’s power is turned off.
¡A “prohibited icon” may appear at
the top-right on the TV screen dur-
ing operation, warning that a pro-
hibited operation has been encoun-
DVD-V
1
Press TITLE on the remote control.
¡The title menu will appear.
2
3
If the feature is not available,
may appear on the TV screen.
symbol
Press Arrow (K/L/s/B) to select an item
and ENTER to confirm selection.
tered by the DVD or the disc.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
CALLING UP A MENU SCREEN
DURING PLAYBACK
¡Press DISC MENU to call up the DVD menu.
¡Press TITLE to call up the title menu.
NOTE
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
EN
–
–
20
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
FAST FORWARD/REVERSE
SEARCH
RESUME
DVD-V
CD
MP3
DVD-V
CD
MP3
1
During playback, press STOP.
¡Resume message will appear on the TV screen.
1
During playback, press FWD g or
REV h .
¡“ g 1” or “h 1” appears on the screen.
To select another speed, repeat step1 until
your required speed appears on the screen.
¡For DVDs, fast forward/reverse search speed is dif-
ferent depending on the disc. Approximate speed is
1(×2), 2(×8), 3(×50) and 4(×100).
2
Press PLAY, playback will resume from the
point at which playback was stopped.
2
¡To cancel resume, press STOP twice.
¡If TV/DVD is turned off, resume function will be
cancelled.
¡For MP3, playback will resume from the beginning
of the track at which playback was stopped.
¡For audio CDs, approximate speed is ×16.
¡For MP3, approximate speed is ×8
¡When you use buttons on the TV/DVD front panel,
press and hold NEXT G / SEARCH g or
PREV H / SEARCH h for a few seconds.
PAUSE
DVD-V
CD
MP3
3
To return to normal playback, press PLAY.
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
SLOW FORWARD /
SLOW REVERSE
2
To continue playback, press PLAY.
DVD-V
STEP BY STEP PLAYBACK
1
2
During playback, press PAUSE.
Press FWD g or REV h .
DVD-V
¡“
1” or “
1” appears on the screen.
1
During playback, press PAUSE.
¡Playback will pause and sound will be muted.
3
To select another speed, repeat step2 until
your required speed appears on the screen.
¡Slow forward or reverse speed varies with the disc.
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).
¡When you use buttons on the TV/DVD front panel,
press and hold NEXT G / SEARCH g or
PREV H / SEARCH h for a few seconds.
2
3
The disc goes forward by one frame each
time PAUSE is pressed.
To exit step by step playback, press PLAY.
4
To return to normal playback, press PLAY .
EN
–
–
21
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
MP3
DVD-V
CD
There are three ways to begin playback on an Audio
CD and MP3 at a specific track.
1
2
During playback, press SEARCH MODE
three times (CD: twice) to display the Time
Search on the TV screen.
Using the number buttons on the remote control
Within 30 seconds, enter a desired disc
time using the number buttons.
1
Press the number buttons to enter the
desired track number.
¡Playback will start at the specified time.
¡Press CLEAR to erase the incorrect input.
¡When there is no need to enter a number, “0”
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
appears automatically. For example, “ 0 : 0
:
”
-
- -
appears in the Time Search display if the total time
of the disc is less than 10 minutes.
¡To play track 26, press +10, 2, 6.
Using SEARCH MODE
1
Press SEARCH MODE.
MARKER SETUP SCREEN
¡The Track search display appears.
DVD-V
CD
2
Within 30 seconds, select a desired track
number using the number buttons.
Use markers to memorize your favorite places on a disc.
¡For single digits press 0 first, if the total track of the
disc is more than 10 tracks.
¡Playback will start at the selected track.
1
Press SEARCH MODE four times (CD: three
times) during playback.
¡The display screen and Markers will appear on the
TV screen.
Using PREV/NEXT
H
G
During playback, press NEXT G to move the next
track. Press it repeatedly to skip subsequent tracks.
Press PREV H to go back to beginning of the current
track. Press it repeatedly to go to the previous tracks.
¡If SKIP is pressed while the playback is paused, the
playback will be paused again after skipping to the
next track.
2
Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,
7, 8, 9, or 10 and ensure that “
appears in the display.
:
:
”
- - - - - - - -
3
When you reach the desired point, press
ENTER.
¡The title or track and elapsed playing time will appear
in the TV screen.
NOTE
¡PREV/NEXT
H
G are not available when play-
back is stopped.
4
To return to the Marker later, press SEARCH
MODE four times (CD: three times) during
playback and Arrow (s /B) to choose the
desired marker, then press ENTER.
TITLE / CHAPTER SEARCH
NOTES
DVD-V
¡Opening the disc tray or turning off the power or
selecting AC at step 2 and pressing ENTER will
erase all Markers.
¡To clear a marker, using Arrow (s /B), position the
cursor on to the marker number to be cleared and
press CLEAR.
1
Press SEARCH MODE once for the Chapter
search, twice for the Title search during
playback.
_/2
¡You can mark up to 10 points.
2
Enter the desired chapter/title number using
the number buttons.
5
Press SEARCH MODE or RETURN to exit.
¡Playback will start at the selected chapter or title.
¡Press CLEAR to erase the incorrect input.
¡For single digits press 0 first, if the total chapter or
title of the disc is more than 10.
EN
–
–
22
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
REPEAT is available only during playback.
CD
REPEAT TITLE / CHAPTER
You may determine the order in which tracks will play.
DVD-V
1
In stop mode, press MODE.
¡The PROGRAM screen will appear.
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
2
Press Arrow (▲/▼) to select a track, then
press ENTER.
TOTAL
CHAPTER
(current chapter repeat) (current title repeat)
TITLE
OFF
(repeat off)
¡Press CLEAR to erase the most
recently entered program.
NOTES
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
3
4
Repeat step 2 until you have selected all the
tracks you want to play in the program.
Press PLAY to play the programmed tracks.
NOTES
REPEAT TRACK
CD
¡While the program is being played back, the STOP
works as follows.
¡Press STOP once and then PLAY again, playback
will restart from the point where STOP was pressed.
(Program continued)
¡Press STOP twice and then PLAY again, playback will
restart from the track in the usual way. (Program cleared)
¡Up to 99 programs can be entered.
¡To erase all programs at once, select ALL CLEAR at
the bottom of the list at Step2.
¡If you like to repeat the current track in the program,
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
TRACK
(current track repeat)
ALL
OFF
(repeat off)
(entire disc repeat)
press REPEAT repeatedly until
TRACK appears
NOTES
during playback. If you like to repeat the entire pro-
¡Repeat setting will be cleared when moving to other
gram press REPEAT repeatedly until
appears during playback.
ALL
track.
¡Repeat playback does not function during repeat A-
RANDOM PLAYBACK
B playback.
REPEAT A-B
CD
DVD-V CD
This shuffles the playing order of tracks instead of
playback in the sequence.
1
2
Press REPEAT A-B at your chosen starting
point.
A- appears briefly on the TV screen.
¡
¡
1
In stop mode, press MODE twice.
¡RANDOM screen appears.
RANDOM
Press REPEAT A-B again at your chosen
end point.
A-B appears briefly on the TV screen and the
CD-DA
TOTAL 0:45:55
RANDOM PROGRAM
- - no indication - -
repeat sequence begins.
PLAY
3
To exit the sequence, press REPEAT A-B.
NOTES
2
Press PLAY to start random playback.
NOTE
¡The repeat A-B section can only be set within the cur-
rent title (for DVDs) or current track (for audio CDs).
¡Repeat A-B is not available with some scenes in DVD.
¡To cancel the A point which was set, press CLEAR.
¡Repeat A-B playback does not function during title,
chapter, track or all repeat playback.
¡If you like to repeat the current track in the random
selection, press REPEAT repeatedly until
TRACK appears during playback. If you like to
repeat the entire random selection press REPEAT
repeatedly until
ALL appears during playback.
EN
–
–
23
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A MP3 DISC
MP3 PLAYBACK
PROGRAM
MP3
MP3
When a CD with MP3 files is in the TV/DVD, press This feature allows you to program an MP3 disc to
DISC MENU to call up the MP3 menu on the TV play in a desired sequence.
screen.
1
In stop mode, press MODE.
¡The PROGRAM screen will appear.
1
In stop mode, press Arrow (K/L) to select
the desired group or
2
Select a desired track using Arrow
(K/L/s/B). Then press ENTER.
track.
folder name 1
¡If a group is selected, press
B
folder name 2
folder name 3
folder name 4
file name 1
or ENTER to go on to the
track selection screen. Press
Arrow (K /L ) to choose a
track, then press ENTER.
¡If a track is selected, press ENTER to start playing
tracks. Starting from the one you’ve just chosen the
subsequent tracks will be played.
¡Press B when you want to go to the next hierarchy.
¡Press s when you want to go back to the previous
hierarchy.
¡Press CLEAR to erase the most recently entered pro-
gram.
file name 2
file name 3
folder name 1
3
Repeat step 2 until you have selected all the
tracks you want to play in the program.
¡Press TITLE to return to the first item.
4
Press PLAY to start programmed playback.
NOTES
2
Press STOP to stop playback.
¡While the program is being played back, the STOP
works as follows.
¡Press STOP once and then PLAY again, playback
will restart from the point where STOP was pressed.
(Program continued)
¡Press STOP twice and then PLAY again, playback will
restart from the track in the usual way. (Program cleared)
¡To erase all programs at once, select ALL CLEAR at
the bottom of the list at Step2.
NOTES
¡Folders are known as Groups; files are known as
Tracks.
3
¡MP3 files are accompanied by
icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 512 files can be recognized.
¡Up to 8 hierarchies can be created.
This TV/DVD recommends the use of files recorded at
the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
RANDOM PLAYBACK
MP3
1
In stop mode, press MODE twice.
¡RANDOM screen appears.
REPEAT
MP3
2
Press PLAY to start random playback.
REPEAT is available only during playback.
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
GROUP
(current group
repeat)
ALL
(entire disc
repeat)
OFF
(repeat off)
TRACK
(current track
repeat)
NOTE
¡Repeat setting will be cleared when moving to other
track.
EN
–
–
24
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
CAMERA ANGLE
DVD-V
DVD-V
The TV/DVD allows you to select a language for sub- Some DVD discs contain scenes which have been shot
titles during DVD disc (if available) playback. simultaneously from various angles. You can change
the camera angle when the (
screen.
) icon appears on the
1
2
Press SUBTITLE during playback.
Press SUBTITLE repeatedly to select your
desired subtitle language.
1
Press ANGLE during playback.
¡The selected angle will be displayed on the display
¡The subtitle language will be displayed on the dis-
play bar at the top of the screen.
bar at the top of the screen.
2
Press ANGLE repeatedly to select your
desired angle.
3
To turn off subtitles, press SUBTITLE
repeatedly until OFF appears.
NOTES
BLACK LEVEL SETTING
¡
Some discs allow audio language setting/subtitle language
setting on the disc menu. (Operation varies between discs,
so refer to the manual accompanying the disc.)
DVD-V
¡If the desired language is not shown after pressing
SUBTITLE several times, the disc does not have
subtitles in that language.
Adjust the Black Level Settings to make the black
parts of the picture brighter.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 27.)
1
Press MODE during playback.
OFF
2
Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter.
AUDIO LANGUAGE
OFF: Shows the original picture as recorded.
DVD-V
3
Press MODE twice or RETURN to exit.
NOTE
The TV/DVD allows you to select a language during
DVD disc (if multi languages are available) playback.
¡The setting will be saved even if the TV/DVD is
turned off.
1
2
Press AUDIO during playback.
VIRTUAL SURROUND
Press AUDIO repeatedly to select your
desired language.
DVD-V
CD
MP3
NOTE
¡Pressing AUDIO may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
You can enjoy surround-sound effect over two speak-
ers on this TV/DVD.
1
Press V.SURR once or MODE twice
(CD/MP3: once) during playback.
STEREO SOUND MODE
CD
OFF
1
Press AUDIO repeatedly during playback to
select between STEREO, L-CH or R-CH.
2
3
Press ENTER to set it 1 (Natural effect) or 2
(Emphasized effect) or OFF.
¡STEREO - both right and left channels are active
(stereo)
L-CH - only left channel is active
R-CH - only right channel is active
NOTE
¡If the Virtual Surround setting is ON, the sound
mode will be fixed to STEREO and can not be
Press V.SURR or MODE or RETURN to exit.
NOTE (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
EN
–
–
25
changed.
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
THE ON-SCREEN INFORMATION
DVD-V
CD
MP3
You can check the information about the current disc by pressing DISPLAY on the remote control.
For DVD-Vs
For audio CDs
1
Press DISPLAY during playback to show
current Chapter.
1
Press DISPLAY during playback to show the
current Track.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
9/49
0:00:00 -0:03:30
2
Press DISPLAY again to show current Total
Track.
2
Press DISPLAY again to show current Title.
¡The elapsed and remaining playing time of the cur-
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
rent title will be displayed.
3
Press DISPLAY again.
¡The BIT RATE and the current repeat setting will be
displayed.
3
Press DISPLAY again to exit the display.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
For MP3
1
Press DISPLAY during playback.
¡The name of the file currently in play will be dis-
4
Press DISPLAY again to exit the display.
played.
2
Press DISPLAY again to show the track
number, the elapsed time, the repeat status
and the playback status at the top of the
screen.
¡
will be displayed when repeat play has been
selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3
Press DISPLAY again to exit the display.
EN
–
–
26
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE DVD SETUP ITEMS
LANGUAGE SETTING
Language
Code Language
Code
DVD-V
A-B
L-N
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
4748 Laothian
4747 Latin
4752 Latvian;Lettish
6563 Lingala
4759 Lithuanian
4764 Macedonian
5471 Malagasy
4765 Malay
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Language options are not available with some discs.
1
Press SETUP twice in STOP mode so that
the DVD SETUP menu appears.
¡If the menu does not appear, press PLAY, STOP,
4771 Malayalam
4772 Maltese
4847 Maori
then SETUP twice.
5167 Marathi
SETUP
4860 Moldavian
5072 Mongolian
4854 Nauru
QUICK
CUSTOM
INITIALIZE
4855 Nepali
4864 Norwegian [NOR]
4853
5971 Occitan
4851 Oriya
Oromo(Afan)
5759 Panjabi
4947 Pashto;Pushto
7254 Persian
4961 Polish
5464 Portuguese [POR]
4965 Quechua
5047 Rhaeto-Romance
6058 Romanian [RUM]
5160 Russian [RUS]
5161
5166 Samoan
Sangho
5261 Sanskrit
5256 Scots Gaelic
5255 Serbian
Bulgarian
Burmese
Byelorussian
O-R
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
2
Press Arrow L to select “CUSTOM”, then
C-E
press ENTER.
Cambodian
Catalan
¡CUSTOM mode will appear.
Chinese [CHI]
Corsican
Croatian
3
Press Arrow (K/L) to select “LANGUAGE”,
Czech
then press ENTER to confirm.
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
SETUP
CUSTOM
S
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
LANGUAGE
DISPLAY
AUDIO
F-H
Faroese
Fiji
PARENTAL
Finnish [FIN]
French [FRE]
Frisian
5264 Serbo-Croatian
5271 Sesotho
5358 Setswana
5747 Shona
4
Press Arrow (K/L) to select the next items,
Galician
then press ENTER.
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
5051 Sindhi
AUDIO: Sets the audio language.
5158 Singhalese
5758 Siswat
5360 Slovak
SUBTITLE: Sets the subtitle language.
DISC MENU: Sets the language for DVD menu.
Gujarati
Hausa
Hebrew
5367 Slovenian
5447 Somali
5569 Spanish [SPA]
5455 Sundanese
5467 Swahili
5
Press Arrow (K/L) to select a setting, then
press ENTER.
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Swedish [SWE]
¡If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list.)
¡Only the languages supported by the disc can be
selected.
5565
5560 Tagalog
5547 Tajik
5551 Tamil
5557 Tatar
5347 Telugu
5566 Thai
T
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
5647 Tibetan
5669 Tigrinya
5760 Tonga
5765 Tsonga
5757 Turkish [TUR]
6469 Turkmen
5771 Twi
6
Press SETUP to exit.
Kazakh
NOTE
Kinyarwanda
Kirghiz
Kirundi
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the AUDIO and the
SUBTITLE button. Details are on page 25.
6460
U-Z
Korean [KOR]
Kurdish
5761 Ukrainian
5767 Urdu
Uzbek
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
TO CHANGE THE ON-SCREEN MENUS
You can access the TV SETUP menu by pressing
SETUP from the DVD mode. Refer to “Selecting the
Language” on page 13 to changing the on-screen
menus.
Yoruba
Zulu
If you choose a Language that has a 3 letter language
code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 25. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
EN
–
–
27
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY SETTING
AUDIO SETTINGS
DVD-V
DVD-V
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
Choose the appropriate Audio settings for your equip-
ment as it only affects during the playback of DVD
discs.
1
Press SETUP twice in STOP mode so that
the DVD SETUP menu appears.
1
Press SETUP twice in STOP mode so that
the DVD SETUP menu appears.
¡If the menu does not appear, press PLAY, STOP,
then SETUP twice.
¡If the menu does not appear, press PLAY, STOP,
then SETUP twice.
SETUP
SETUP
QUICK
CUSTOM
INITIALIZE
QUICK
CUSTOM
INITIALIZE
2
Press Arrow L to select “CUSTOM”, then
press ENTER.
2
Press Arrow L to select “CUSTOM”, then
press ENTER.
¡CUSTOM mode will appear.
¡CUSTOM mode will appear.
3
Press Arrow (K/L) to select “DISPLAY”,
then press ENTER to confirm.
3
Press Arrow (K/L) to select “AUDIO”, then
press ENTER to confirm.
SETUP
CUSTOM
LANGUAGE
DISPLAY
AUDIO
SETUP
CUSTOM
PARENTAL
LANGUAGE
DISPLAY
AUDIO
4
Press Arrow (K/L) to select the below
items, then press ENTER.
PARENTAL
TV MODE:
QUICK
4
Press Arrow (K/L) to select the below
items, then press ENTER.
¡Press Arrow (K/L) for an item selection, then press
ENTER.
¡Select 4:3 LETTER BOX for black bars to appear on
top and bottom of the screen.
DRC (Dynamic Range Control):
¡To compress the range of sound volume.
¡The default setting is ON.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
¡The default setting is 4:3 LETTER BOX.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be acti-
vated and sound will be down sampled at 48kHz.
STILL MODE:
¡Press Arrow (K/L) for an item selection, then press
ENTER.
¡Select “AUTO” usually.
¡If you select “FIELD”, the picture in the still mode
will be stabilized.
¡If you select “FRAME”, the picture in the still mode
will be highly defined.
DOLBY DIGITAL:
Set to On when the unit is connected to a Dolby Digital
Decoder.
(ON: Output by Dolby Digital)
(OFF: Convert the Dolby Digital to PCM (2 channel
stereo))
QUICK
ANGLE ICON:
¡Press ENTER repeatedly to turn Angle icon ON or
OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡The default setting is ON.
¡Press ENTER repeatedly to turn Auto Power off ON
or OFF.
5
Press SETUP to exit.
¡
The default setting is ON and the screen saver program
starts when there is no input form the TV/DVD for 5
minutes is the stop mode. When the screen saver pro-
gram is activated for 15 minutes, the power automati-
cally turns off.
5
Press SETUP to exit.
EN
–
–
28
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL LEVELS
PARENTAL CONTROL
¡
ALL
All parental lock is cancelled.
DVD-V
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
¡
Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
¡
Level 1
PARENTAL LEVEL
Only DVD software intended for children can be
played back, with those intended for adult and
general use is prohibited.
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
1
Press SETUP twice in STOP mode so that
the QUICK SETUP menu appears.
IF YOU FORGET THE PASSWORD
¡If the menu does not appear, press PLAY, STOP,
1
Press 4, 7, 3, 7 at step 4. Then enter your
new password.
then SETUP twice.
¡Password will be cleared and parental level will be
SETUP
set to ALL.
QUICK
CUSTOM
INITIALIZE
2
Follow Steps [5]-[7] again.
2
3
Press Arrow L to select “CUSTOM”, then
press ENTER.
INITIALIZE
This allows you to return all selections of SETUP
(except for PARENTAL) to their default settings.
Press Arrow (K/L) to select “PARENTAL”,
then press ENTER.
1
2
3
Press SETUP twice in STOP mode so that
the INITIALIZE menu appears.
SETUP
CUSTOM
LANGUAGE
DISPLAY
AUDIO
Press Arrow (K/L) to select “INITIALIZE”,
then press ENTER.
PARENTAL
Select “YES”, then press ENTER twice. All
the settings (except for “PARENTAL”) will be
cleared.
4
5
6
7
Enter your four-digit password then press
ENTER.
¡To cancel the initialization, select “NO”.
Press Arrow (K/L) to select PARENTAL
LEVEL, then press ENTER.
4
Press SETUP to exit.
Press Arrow (K/L) to select the desired
level, then press ENTER.
Press SETUP to exit
NOTES
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password from the second time onward.
¡To change the password, press Arrow (K/L) to
select CHANGE at step 5, then press ENTER. Enter
the four-digit password, then press ENTER.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
EN
–
–
29
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the
TV/DVD, consulting the following checklist.
Problem
Corrective Action
Make sure the power plug is connected to an AC outlet.
Make sure the power is turned on.
Check if the power plug is connected to an AC outlet.
Check the batteries in the remote control.
Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote.
You have to be within 23 feet of the TV/DVD.
No power
•
•
•
•
•
The TV/DVD does not respond to
the remote control.
•
•
Check if the correct mode is selected. If not switch the mode by
pressing SELECT on the remote control,whichever you need.
TV Mode
Problem
Corrective Action
No Picture or Sound
Try a new channel, if OK, then possible station trouble.
Make sure the power is turned on.
Press SELECT on the remote control to select TV mode. Then try
other TV feature.
•
•
•
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust COLOR control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust CONTRAST & BRIGHT control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Bars On Screen
Picture Distorted or Blurred
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
Adjust CONTRAST & BRIGHT control.
Try a new channel, if OK, then possible station trouble.
Check for local interference.
Magnetism from nearby appliances and geomagnetism might affect
the color of the TV picture. Move the TV/DVD away from the appli-
ances, the TV/DVD can repair itself automatically. If you want to
repair immediately, unplug the TV/DVD power cord, then plug it in
again 30 minutes or so later.
Picture OK, Sound Poor
Different color marks on screen
EN
–
–
30
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed Caption Problem
My TV/DVD is showing captions
that are misspelled.
Possible Remedy
• You are watching a live broadcast and spelling errors made by the
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/DVD will not show the text • Captions that are delayed a few seconds behind the actual dialogue
in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies
what is being said.
• can display a dialogue to a maximum of 220 words per minute. If a
• dialogue exceeds that rate, selective editing is used to insure that the
• captions remain up-to-date with the current TV screen dialogue.
• Interference caused by building, power lines, thunderstorms, etc.
• may cause scrambled or incomplete captions to appear.
My captions are scrambled with
white boxes on the TV screen.
My program guide listed a TV show • Broadcasters may at times use a time compression process to the
as being closed captioned but none • actual program so that additional advertising time can be given.
of the captions were displayed.
• Since the decoder cannot read the compressed information,
• captions will be lost.
My TV/DVD screen shows a black • You are in the TEXT mode. Select CAPTION mode or CAPTION
box on certain channels.
• [OFF].
DVD Mode
Problem
Corrective Action
No picture
• Insert a correct video disc that plays on this TV/DVD.
• Press SELECT on the remote control to select DVD mode. Next,
press PLAY or OPEN/CLOSE. Then, try other DVD feature.
• Insert the disc.
Disc cannot be played
No sound
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This TV/DVD does not support DTS audio. This is not a malfunction.
• There are some cases where pictures may be slightly distorted, which
are not a sign of a malfunction.
No DTS audio is output
Distorted picture
• Although pictures may stop for a moment, this is not a malfunction.
• The selected language is not available for audio or subtitles on the
DVD.
Audio or subtitle language
does not match the set up
This is not a malfunction
The camera angle cannot be
changed
• The DVD does not contain sequences recorded from different camera
angles. This is not a malfunction
Audio or subtitle language cannot
be changed
• The DVD does not contain audio source or subtitles in the selected
language. This is not a malfunction.
“Prohibited icon” appears on the
screen, prohibiting an operation
CD sound dropout
• That operation is prohibited by the TV/DVD or the disc.
This is not a malfunction.
• Scratched disc. Replace the disc with an unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
NOTES:
Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
•
EN
–
–
31
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CABINET CLEANING
SERVICING
Wipe the front panel and other exterior surfaces of
the TV/DVD with a soft cloth immersed in luke-
warm water and wrung dry.
Never use a solvent or alcohol. Do not spray insec-
ticide liquid near the TV/DVD. Such chemicals
may cause damage and discoloration to the
exposed surfaces.
Should your TV/DVD become inoperative, do not
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord and please call our help line at 1-800-
605-8610, to locate an Authorized Service Center.
•
•
•
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
If the TV/DVD still does not perform properly when it is operated while referring to the relevant sections and
to "TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty.
•
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup
unit.
DISC HANDLING
Use discs which have the following logos on them.
(Optical audio digital discs.)
•
To clean-off, use a soft cloth.
Do not use a hard cloth since this will mar the disc.
Wipe the disc in a straight line from center to edge.
Never wipe with a circular motion.
•
•
•
•
•
ReWritable
Recordable
Do not use detergent or abrasive cleaning agents.
Handle the discs so that fingerprints and dust do
not adhere to the surfaces of the discs.
•
Always store the disc in its protective case when it
is not used.
•
EN
–
–
32
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
TV
CRT :
20 inch in-line gun,
90˚ deflection tube
NTSC-M
OTHER SPECIFICATIONS
Terminals
Television system:
Antenna input:
VHF/UHF/CATV
TV Standard
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
Closed caption system: §15.119/FCC
Channel coverage:
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output
(only DVD):
VHF:
UHF:
CATV:
2 ~ 13
14 ~ 69
2 ~13, A ~ W,
W+1 ~ W+84,
A-5 ~ A-1, 5A
181 channel
1/8” stereo (3.5 mm)
One pin jack,
500m Vpp (75 ohm)
Digital encoded
Tuning System:
Channel access:
Remote control:
frequency synthesized
tuning system
Direct access keyboard,
programmable
scan and up/down
infrared light system
Operating
temperature:
5°C to 40°C
(41°F~104°F)
Power requirements: AC 120V, 60Hz
Power consumption
(Maximum) :
Dimensions :
80W
H:20-3/16”(514mm)
W:20-3/16”(512mm)
D:19-13/16”(503mm)
49.6lbs(21.0kg)
DVD
Weight :
Discs:
DVD video, Audio CD
Output signal format: NTSC color
Designs and specifications are subject to change without notice.
If there is a discrepancy between languages, the default language will be English.
•
•
EN
–
–
33
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Botón PREV (SKIP)
H
INDICE
Reproduce desde el inicio del capítulo o canción actual.
Botón SEARCH (REV) h (panel delantero)
Durante la reproducción o en el modo de pausa,
mantenga presionado el botón durante unos segundos
para cambiar la velocidad de reproducción hacia atrás.
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 34
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 34
MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 34
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 35
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 35
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 35
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 36
CONEXIÓN A UN AMPLIFICADOR EQUIPADO
10. Botón PLAY
Inicia la reproducción del contenido del disco.
Púlselo para cambiar a un modo de DVD cuando esta
en el modo de televisor.
11. Botón NEXT (SKIP)
G
CON TOMAS DE ENTRADA DIGITAL, PLATINA
MD O PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . 36
CONEXCIONA UN DECODIFICADOR DOLBY
Reproduce desde el inicio del siguiente capítulo o
canción.
Botón SEARCH (FWD) g (panel delantero)
Durante la reproducción o en el modo de pausa,
mantenga presionado el botón durante unos segundos
para cambiar la velocidad de reproducción en avance.
DIGITAL (Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
TV SECTION
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 37
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 37
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12. Botón PAUSE
Hace una pausa en la operación del disco.
13. Botón OPEN/CLOSE
Púlselo para insertar discos en la bandeja o retirarlos
de ella.
DVD SECTION
■ REPRODUCCIÓN DE UN DVD DE VÍDEO O UN
CD DE AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
REPRODUCCION BASICA . . . . . . . . . . . . . . . . . . . . . . 38
14.Toma HEADPHONE
Para conectar auriculares (no suministrados) y
escuchar en privado.
CONTROLES DE
15. Botón MODE
Activa el modo de reproducción programada o el
modo de reproducción aleatoria cuand se reproducen
CDs o MP3.
OPERACIÓN Y FUNCIONES
PANEL FRONTAL DEL
TELEVISOR/DVD
16. Botones de números
Modo del televisor:
Pulse dos dígitos para tener acceso directamente al
canal deseado.
Consulte la figura 1 de la página 8
Recuerde pulsar "0" antes de elegir un canal de un
solo dígito.
MANDO A DISTANCIA
Botón +100
Púlselo para seleccionar canales de televisión por
cable cuyo número sea igual o superior al 100.
Modo DVD:
Consulte la figura 2 de la página 8
VISTA POSTERIOR
Púlselo para introducir el número deseado.
Botón +10
Púlselo para introducir los números deseados cuyo
número sea igual o superior al 10.
Consulte la figura 3 de la página 9
1. Bandeja de carga del disco
17. Botón SLEEP
2.Toma de entrada VIDEO
Pulse el botón SLEEP para visualizar el temporizador
para dormir y activar la función. La hora de apagado
puede determinarse por el número de veces que usted
pulsa el botón. (0, 30, 60, 90 o 120 minutos)
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
3.Tomas de entrada AUDIO L/R
18. Botón REV
h
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
Presione para ver la imagena en DVD en retroceso
rápido. Presione PAUSE y presione este botón para
empezar la reproducción en cámara lenta. Presione
repetidamente este botón para cambiar la velocidad en
avance de la cámara lenta.
4. Botón POWER
Púlselo para conectar y desconectar la alimentación.
5. Botones VOLUME K/L(VOL.
m/n)
Púlselos para controlar el nivel del volumen para el
DVD y el televisor.
Botón FWD
g
Presione para avanzar rápidamente en el disco.
Presione PAUSE y presione este botón para empezar
la reproducción en cámara lenta. Presione
repetidamente este botón para cambiar la velocidad
de avance de la cámara lenta.
6. Botones CHANNEL K/L(CH.K/L)
Púlselo para seleccionar el canal memorizado.
Púlselo para cambiar a un modo de televisor cuando
esta en el modo de DVD.
7. Ventanilla del sensor del mando a distancia
19. Botón V.SURR
8. Botón STOP
Púlselo para activar/desactivar el envolvente virtual.
Detiene la operación del disco.
20. Botón SETUP
Púlselo para activar o salir del modo de menús de
televisor o preparación de DVD.
ES
–
–
34
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Botón TITLE
37. Cable de alimentaciónConéctelo a una toma de
CA convencional (120 V/60 Hz).
Visualiza el menú de títulos.
NOTA: Retire el cable de alimentación del gancho
para evitar romperlo antes de conectarlo a una
toma de CA convencional.
22. Botón CLEAR
Repone un ajuste.
23. Botón DISPLAY
38.Toma de salida de audio digital COAXIAL
(DVD Audio solamente)
Modo del televisor:
Púlselo para visualizar el número del canal en la
pantalla. Si lo pulsa de nuevo, el número del canal
desaparecerá.
Conéctela a la entrada digital de un amplificador o
decodificador externo.
Modo de DVD:
Visualiza el estado actual en la pantalla del televisor
con fines de comprobación.
39.Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por
cable o sistema de satélite.
24. Botón SEARCH MODE
Púlselo para localizar un punto deseado.
PARA INSERTAR LAS PILAS
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a distancia en el
sentido de la flecha.
2) Inserte 2 pilas "AA" en el compartimiento de las
pilas, en el sentido indicado por las marcas de
polaridad (+/-).
25. Botón AUDIO
Púlselo para seleccionar un idioma de audio o un
modo de sonido deseado.
26. Botón SUBTITLE
Púlselo para seleccionar un idioma de subtítulos
deseado.
27. Botón REPEAT
Repite la reproducción del disco, título, capítulo,
grupo o pista actual.
3) Vuelva a poner la cubierta.
28. Botón ANGLE
NOTAS:
Púlselo para cambiar el ángulo de la cámara y ver,
desde un ángulo diferente, la secuencia que está
siendo reproducida.
No mezcle pilas alcalinas y de manganeso.
•
No mezcle pilas viejas y nuevas.
•
29. Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
30. Botón RETURN
PREPARACIÓN PARA LA
UTILIZACIÓN
Vuelve a la operación anterior en el modo de
instalación del DVD.
31. Botón ENTER
Púlselo para establecer un ajuste.
CONEXIONES DE
ANTENA/CABLE
32. Botones de flechas
Modo de televisor:
Púlselo para seleccionar un modo de ajuste desde el
menú que aparece en la pantalla del televisor.
Púlselo para seleccionar o ajustar desde un menú
particular.
Consulte la figura 4 de la página 10
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención del
instalador de sistemas CATV para que tenga en
cuenta el Artículo 820-40 del NEC, el cual
proporciona consejos para hacer una conexión a
tierra apropiada y, en particular, especifica que la
tierra del cable deberá estar conectada al sistema de
puesta a tierra del edificio, tan cerca del punto de
entrada del cable como sea posible.
Modo de DVD:
Se utiliza cuando se hacen ajustes mientras se
observa la visualización en una pantalla de televisor.
33. Botón DISC MENU
Visualiza menús en el DVD.
34. Botón SELECT
Púlselo para cambiar a un modo de televisor, modo
de entrada externa o modo de DVD.
NOTA: Cuando seleccione el modo DVD con
este botón, pulse primero PLAY u
NOTA:
Antes de enchufar la antena a la toma ANT.IN del
televisor/DVD, compruebe que la clavija no esté
doblada. Si esta doblada, póngala derecha como se
muestra en la ilustración, y luego conéctela en la
toma ANT.IN del televisor/DVD.
Clavija doblada
OPEN/CLOSE. De lo contrario, las funciones del
DVD no se activarán.
35. Botón MUTE
Pulse el botón MUTE para apagar el sonido de un
programa de TV. (La visualización del nivel del
sonido cambia de ROJO CLARO a AZUL CLARO.)
Pulse de nuevo el botón MUTE o el botón VOL m o
n para restaurar el sonido.
Cable
Clavija
(Necesita enderezarse)
(Clavija derecha)
36. Botón PICTURE
Presione para entrar en el modo de ajuste de imagen.
ANTENA COMBINADA DE VHF/UHF
La antena combinada de VHF/UHF de 75 ohmios
puede conectarse al terminal ANT.
ES
–
–
35
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTA:
Cuando conecte una videograbadora monofónica
(otra fuente) a este televisor/DVD, conecte la toma
de salida de audio de la videograbadora
ANTENA SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena
exterior.
•
TELEVICION POR CABLE SIN CAJA
DE CONVERTIDOR / DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su televisor/DVD sin
una caja de convertidor. Utilice el mando a distancia
del televisor/DVD para seleccionar los canales.
monofónica (otra fuente) a la toma AUDIO L de
este televisor/DVD. El audio saldrá igualmente por
los canales izquierdo y derecho.
Consulte la figura 5 de la página 11
CONEXIÓN A UN
TELEVICION POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATRLITE
AMPLIFICADOR EQUIPADO
CON TOMAS DE ENTRADA
DIGITAL, PLATINA MD O
PLATINA DAT (Para DVD)
Si su compañía de televisión por cable le suministra
una caja de convertidor, o si usted utiliza un sistema
de satélite, usted podrá utilizar la conexión básica
mostrada aquí.
Utilice un cable digital coaxial de audio de venta en
el comercio especializado para hacer las conexiones
de audio.
La selección de los canales deberá hacerse con la caja
de convertidor o con la caja de satélite. Esto significa
que los canales no se podrán cambiar utilizando el
mando a distancia del televisor/DVD.
Consulte la figura 6 de la página 11
NOTAS:
PARA VER UN CANAL
CODIFICADO/DECODIFICADO
1) Ponga el selector de canales del televisor/DVD
en la posición del canal de salida de la caja de
convertidor de televisión por cable o de la caja de
satélite. (Ej., CH3)
2) Seleccione el canal que va a ver en su caja de
convertidor de televisión por cable o caja de
satélite.
La fuente de audio de un disco en un formato de
•
sonido ambiental Dolby Digital de 5,1 canales no
se puede grabar como sonido digital mediante una
platina MD o DAT.
Asegúrese de desconectar la alimentación de todos
los componentes antes de conectar otro
componente.
•
Consulte los manuales del propietario de los
componentes que va a conectar al televisor/DVD.
•
Ponga DOLBY DIGITAL en OFF para la salida de
•
CONEXIÓN A TOMAS DE
ENTRADA EXTERNA
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de
entrada de audio/vídeo de la parte delantera del
televisor/DVD.
audio en el modo de preparación. La reproducción
en un televisor/DVD utilizando ajustes incorrectos
puede causar distorsión de ruido, y también se
pueden dañar los altavoces. (Consulte la página 28
para poner DOLBY DIGITAL en OFF.)
Conecte las tomas de salida de audio/vídeo de otra
fuente a las tomas AUDIO L/R y VIDEO de este
televisor/DVD. Luego pulse SELECT hasta que
aparezca "AUX" en la pantalla.
ES
–
–
36
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
CONEXCIONA UN
DECODIFICADOR DOLBY
DIGITAL (Para DVD)
TV SECTION
PREPARACIÓN PARA LA
UTILIZACIÓN
Si utiliza este televisor/DVD para reproducir un disco
DVD en un formato de sonido ambiental Dolby
Digital de 5,1 canales, el televisor/DVD dará salida a
un flujo de datos DOLBY DIGITAL desde su toma
de salida de audio digital COAXIAL. Conectando el
reproductor a un decodificador Dolby Digital, usted
podrá disfrutar de un ambiente más convincente y
real, con un sonido ambiental potente y de alta
calidad similar al de los cines.
SELECCIÓN DE IDIOMA
TV
1 Enchufe el cordón de alimentación
del televisor/DVD
Enchufe el cordón de alimentación del
televisor/DVD en una toma de CA están-
dar.
Utilice cables digitales coaxiales de audio disponibles
en el comercio especializado para hacer las
conexiones de audio.
NOTA:
Si aparecen algunas cifras en la esquina de la pan-
talla, pulse el botón POWER sin desenchufar el
cordón de alimentación.
•
Consulte la figura 7 de la página 12
NOTAS:
Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conector a
otro componente.
•
Asegúrese de que ...
Pulse el botón POWER para encender el televi-
sor/DVD.
NOTA: Esta función afecta sólo el idioma en el menú
de la pantalla y no la fuente de audio.
•
Consulte los manuales del propietario de los
componentes que vaya a conectar al televisor/DVD.
Si conecta un decodificador Dolby Digital, ponga
DOLBY DIGITAL en ON para la salida de audio
en el modo de preparación. (Consulte la página 28
para poner DOLBY DIGITAL en ON.)
•
•
- TV SETUP -
2 Seleccione “LANGUAGE”
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Pulse el botón SETUP en el mando
A menos que se haga la conexión a un
•
B
a distancia.
decodificador Dolby Digital , ponga DOLBY
DIGITAL en OFF para la salida de audio en el
modo de preparación. La reproducción en el
televisor/DVD utilizando ajustes incorrectos puede
generar distorsión de ruido, y también puede
estropear los altavoces.
Pulse el botón K o L para señalar
“LANGUAGE”.
3
Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”
Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS” con el botón ENTER.
4 Salga del modo de idioma
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D
doble son marcas de fábrica de Dolby
Laboratories.
Pulse el botón SETUP en el mando a distancia para
volver al modo del televisor.
NOTA: Si, por alguna razón, el menú está en español
o francés, pulse el botón SETUP en el mando a dis-
tancia, pulse el botón K o L para señalar el
“IDIOMA (ESPAÑOL)” o “LANGAGE
(FRANÇAIS)”, a continuación, pulse el botón
ENTER y pulse el botón SETUP en el mando a dis-
tancia.
ES
–
–
37
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
AJUSTE DE CANAL
DVD SECTION
TV
REPRODUCCIÓN DE UN
DVD DE VÍDEO O UN CD
DE AUDIO
Puede programar el sintonizador para buscar todos
los canales que recibe en su localidad.
NOTA: El canal preparado NO es necesario cuando
esté conectado a una caja de cable o caja de satélite.
Sólo tiene que seleccionar con el selector de canal del
televisor/videograbadora al canal de salida de la caja
de cabe o caja de satélite (por ejemplo el canal CH3).
Seleccione el canal a ver en la caja de cable o caja de
satélite.
REPRODUCCION BASICA
DVD-V
CD
MP3
Para empezar
¡Conecte el interruptor del amplificador y otros
equipos, si fuera necesario.
Asegúrese de que ...
1 Pulse el boton POWER.
¡La alimentación se conectará.
Pulse el botón POWER para encender el televi-
sor/DVD.
•
1 Seleccione “AJUSTE DE CANAL”
Pulse el botón SETUP en el mando
a distancia.
– M E N U –
2 Pulse el botón OPEN/CLOSE.
B
AJUSTE DE CANAL
AJUSTE DE V-CHIP
IDIOMA [ESPAÑOL]`
TITULO [OFF]
¡La bandeja de carga del disco se abrirá.
Pulse el botón K o L para señalar
“AJUSTE DE CANAL”.
A continuación, pulse el botón
ENTER.
3 Ponga el dlsco en la bandeja con el lado
de la eliguta hacia arriba.
2 Empiece el prefijado automático
Pulse el botón K o L para señalar
“AUTOPROGRAMACION DE
AJUSTE DE CANAL
–
–
4 Pulse el botón PLAY.
AGREGAR/BORRAR (CATV)
B AUTOPROGRAMACION DE CA.
CA”.
¡La bandeja se cerrará automáticamente y la
reproducción empezará luego desde el primer
capítulo o pista del disco. Si la reproducción no
empieza automáticamente, pulse PLAY.
A continuación, pulse el botón
ENTER.
El sintonizador busca y memoriza
todos los canales activos en su localidad.
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú aparecerá en la pantalla.
3 Después de buscar
El sintonizador se detiene en el canal memorizado
más bajo.
5
Pulse el botón STOP para detener la repro-
ducción.
Cuando se activa AUTOPROGRAMACION DE
•
CA, donde no hay entrada de señal del televisor,
aparecerá “NO HAY SEÑAL DE TV” en la pan-
talla después de terminar la búsqueda de canales.
El televisor/DVD puede reconocer los canales de
•
TV para que sean canales de TV de antena de cable
con las condiciones de recepción. En este caso,
pruebe nuevamente con el prefijado automático en
las condiciones de recepción fina.
ES
–
–
38
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
ES
–
–
39
0C28
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPHONIC
LIMITED WARRANTY
FUNAI CORP. will repair this MAGNAVOX product, free of charge in the USA in the event of defect in materials
or workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This MAGNAVOX Limited warranty does not apply
to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP. or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE
UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest Funai Authorized Service Center or for general service procedure, please
call 1-800-605-8610 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Telephone: 1-800-242-7158
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0EMN02493
T9008UJ ★★★★★
Download from Www.Somanuals.com. All Manuals Search And Download.
|