Sylvania TV VCR Combo SRC2213E User Manual

OWNER’S

MANUAL

13 INCH COLOR TV/VCR

SRC2213E

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®

is a U.S. registered mark.

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1-800-968-3429

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/VCR to its normal operation.

14.Lightning-For added protection for this TV/VCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/VCR due to lightning and

power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR, ask the service technician to perform routine

safety checks to determine that the TV/VCR is in proper

operating condition.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/VCR.

22.Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

_{Download from Www.Somanuals.c}-_om3_.-_{All Manuals Search And Download.}

9I03

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

ature differences are extreme.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to an

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore if condensation occurs inside the

unit, turn the POWER button on and allow at least 2

hours for the unit to dry out.

3) Connect the equipment to an outlet on a circuit

different from that to which the receiver is con-

nected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer name

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

C TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .5

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C OPERATING CONTROLS AND FUNCTIONS 7

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .18

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .18

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .19

NOISE CANCEL (in the Still mode) . . . . . . . .19

VERTICAL HOLD CONTROL . . . . . . . . . . . .20

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .20

TRACKING ADJUSTMENT . . . . . . . . . . . . . .20

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

ANTENNA/CABLE CONNECTIONS . . . . . . .9

FRONT A/V INPUT . . . . . . . . . . . . . . . . . . . .10

INSTALLING THE BATTERIES . . . . . . . . . . .10

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20

NORMAL RECORDING . . . . . . . . . . . . . . . . .20

OTR (One Touch Recording) . . . . . . . . . . . . . .21

TIMER RECORDING . . . . . . . . . . . . . . . . . . .21

TIMER PROGRAM EXTENSION . . . . . . . . .22

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10

SELECTING THE LANGUAGE . . . . . . . . . . .10

CLOCK SET UP (AUTO / MANUAL) . . . . . .10

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .12

CHANNEL SET UP . . . . . . . . . . . . . . . . . . . .13

DELETING (OR ADDING) CHANNEL . . . . .13

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14

WATCHING A TV PROGRAM . . . . . . . . . . . .14

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14

CLOSED CAPTION SYSTEM . . . . . . . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15

C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25

REAL TIME TAPE COUNTER . . . . . . . . . . . .25

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25

C TROUBLESHOOTING GUIDE . . . . . . . . . . .26

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27

C CABLE CHANNEL DESIGNATIONS . . . . . .27

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

INDICE

CONTROLES DE OPERACIÓN Y

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28

SELECCION DE IDIOMA . . . . . . . . . . . . . . . . .30

AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . .31

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

CONEXIONES DE ANTENA/CABLE . . . . . . . .30

MODO DE ENTRADA EXTERNA . . . . . . . . . . .30

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

_{Download from Www.Somanuals.c}-_om5_.-_{All Manuals Search And Download.}

9I03

FEATURES

Infrared remote control

Trilingual on screen menu display selectable in

English, Spanish, or French

Zero Return–The tape returns to counter of

•

0:00:00 by rewinding or fast forwarding.

Still–“Freeze” the picture at any time, for close

viewing of a particular scene. Only tapes recorded

in SLP mode will show a fairly clear picture.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Lets you set the TV/VCR to advance

the tape by entering the desired playback time you

want to skip.

•

Real time counter–This shows the elapsed record-

ing or playback time in hours, minutes, and sec-

onds. The “–” indication will appear when the tape

is rewound further than the tape counter position

“0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Game mode–Automatically selects front A/V input

mode and allows the TV/VCR display to be suit-

able for use with TV games.

Auto power on and off system–Automatically

turns on the TV/VCR when you insert the cassette,

turns off after auto-rewind, and ejects when the

beginning of the tape is reached.

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

•

OTR (One Touch Recording)–Instant recording in

30 to 480 minutes increments is possible at the

push of the REC/OTR button.

•

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts, and the Weekly timer allows recording to be

made once a week up to the end of the tape.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the record-

ing.

Wake-up/Sleep timer–Allows you to have the

TV/VCR automatically turn on or off at a desired

time.

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

SUPPLIED ACCESSORIES

Remote Control Unit

2 AA Batteries

Rod Antenna

PART NO.

(N0154UD or N0123UD)

PART NO. (0EMN00673 or

0EMN01599 or 0EMN01755)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

- 6 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

- TV/VCR FRONT PANEL -

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

EARPHONE

1 2 3 4 5 6 7 8 910 11 12 1314

- REMOTE CONTROL -

1 VIDEO input jack– Connect to the video output

jack of your video camera, video game or another

VCR.

WAKE-UP

/SLEEP

2 AUDIO input jack– Connect to the audio output

jack of your video camera, video game or another

VCR.

3 POWER button– Press to turn TV/VCR on and off.

Press to activate timer recording.

POWER

EJECT

CHANNEL

RETURN

CHANNEL

VOLUME

VOLUME X / Y buttons– Adjust the volume level.

5 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording.

+100

DISPLAY

MUTE

You may display the main menu on the TV screen

by pressing repeatedly this button on the TV/VCR

until you go below the lowest memorized channel.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback.

6 Remote Sensor Window– Receives the infrared

signals from the remote control.

7 STOP / EJECT button (TV/VCR)– Press to stop the

tape motion. Press in the Stop mode to remove tape

from TV/VCR.

PLAY

REW

F.FWD

STOP

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

TIME SEARCH

COUNTER

RESET

EJECT button (remote control)– Press to remove

tape from TV/VCR.

L button–

Press to select setting modes from the on

screen menu.

•

Press to enter digits when setting program.

(for example: setting clock or timer program)

•

_{Download from Www.Somanuals.c}-_om7_.-_{All Manuals Search And Download.}

9I03

- REAR VIEW -

ANT.

8 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

+100 button– When selecting cable channels which

are higher than 99, press this button first, then press

the last two digits. (To select channel 125, first press

the “+100” button then press “2” and “5”).

s button–

16 MENU button– Press to display the main menu on

the TV screen.

Press to select a mode from a particular menu.

(for example: LANGUAGE or USER’S SET

•

UP)

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 25.)

9 PLAY button– Press to begin playback.

K button–

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

Press to select setting modes from the on

screen menu.

•

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 23.)

Press to enter digits when setting program.

•

(for example: setting clock or timer program)

10 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

COUNTER RESET button– Press to reset counter

to 0:00:00.

20 GAME button– Sets the game mode and selects front

A/V input mode at the same time. (See page 14.)

21 TIME SEARCH button– Press to activate Time

Search mode.

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

23 MUTE button– Mutes the sound. Press it again to

resume sound.

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

25 WAKE-UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See pages 23 and 24.)

26 ANT. terminal– Connect to an antenna or cable

system.

B button–

When setting program (for example: setting

•

clock or timer program), press to determine

your selection and proceed to the next step you

want to input.

Press to determine setting modes from on screen

menu.

Press to select a mode from a particular menu.

(for example: LANGUAGE or USER’S SET

UP)

•

11 REC button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

12 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer Recording.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

27 Power cord– Connect to a standard AC outlet.

(120V/60Hz)

14 Cassette compartment

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

- 8 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

From Cable System

or Satellite Dish

Rod Antenna

(Supplied)

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box

OUT

(Not supplied)

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

ANT.

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied)

Flat twin-lead cable

VHF/UHF COMBINED ANTENNA

VHF/UHF SEPARATE ANTENNAS

The VHF/UHF Rod Antenna (supplied) is detachable. In some areas it will be necessary to use an outdoor

Insert the stem of the antenna into the hole on the

upper-back portion of the TV/VCR. Connect the

VHF/UHF Rod Antenna or VHF/UHF Combination

Antenna to the ANT. terminal of the TV/VCR as

shown in the diagram. For the best reception, fully

extend the VHF/UHF Rod Antenna and make the

necessary adjustments. (Avoid touching the top sec-

tion when adjusting.)

antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR Remote Control to select channels

2) Program one or more unscrambled channels for

Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

NOTE:

Before connecting the Rod antenna into antenna ter-

minal, check that the pin is not bent. If it is bent,

straighten the pin as illustrated, then plug the pin into

antenna terminal.

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

Bent pin

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in the diagram.

Cable Plug

(Straight pin)

(Needs to be straightened)

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

NOTE:

The connection of an Rod antenna may not always

give acceptable TV reception.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

_{Download from Www.Somanuals.c}-_om9_.-_{All Manuals Search And Download.}

9I03

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

INSTALLING THE BATTERIES

1) Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Example: CH3)

2) Select the channel to record from your Cable

Converter Box or Satellite Box.

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

3)Replace the cover.

FRONT A/V INPUT

When using an external input signal (another VCR,

video game or video camera), connect the player’s

audio/video output cables to the AUDIO IN/ VIDEO

IN jacks of your TV/VCR. Then press the CHAN-

NEL K or L button until “AUX” appears on the

screen.

NOTE: “AUX” is found below the

lowest memorized channel.

(Example: CH2)

AUX

SET UP FOR USE

SELECTING THE LANGUAGE

4 Exit the Language mode

Press the MENU button on the remote control to

return to TV mode.

NOTE: If for some reason the menu is in Spanish or

French, press the MENU button on the remote con-

trol, press the PLAY/K button to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then

press the F.FWD/B button, then press the MENU

button on the remote control.

1 Plug in the TV/VCR power cord

Plug the TV/VCR power cord into a

standard AC outlet.

NOTE:

If some digits appear in the corner of

the screen, press the POWER button

without unplugging the power cord.

•

Make sure ...

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

the screen menu and not the audio source.

•

CLOCK SET UP

(AUTO / MANUAL)

The TV/VCR clock must be set correctly before timer

recording is possible. It is suggested that the clock be

set manually when first setting up the TV/VCR. Then,

set to [ON] the auto clock setting which will periodi-

cally correct the setting if necessary.

NOTE: If you cannot receive a station with time

signals, auto clock setting cannot be performed. Use

manual setting only.

– M E N U –

2 Select “LANGUAGE”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

CHANNEL SET UP

USER’S SET UP

remote control.

Press the PLAY/K or STOP/L but-

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SERARCH

ton to point to “LANGUAGE”.

3 Select “ENGLISH”, “ESPAÑOL” or

“FRANÇAIS”

MANUAL CLOCK SETTING

Select “ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the F.FWD/B or

REW/s button.

Make sure ...

The TV/VCR is turned on.

•

- 10 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

In the example below, the clock is to be set to:

DATE May 6th, 2004

8 Start the clock

Press the MENU button on the

remote control.

5:40 PM

SETTING TIME 5:40PM

Although seconds are not dis-

played, they begin counting from

00 when you press the MENU but-

ton on the remote control. Use this

feature to synchronize the clock with the correct

time.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L

button to point to “SETTING

CLOCK”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

NOTE:

Then, press the F.FWD/B button.

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

2 Select “MANUAL CLOCK SET”

Press the PLAY/K or STOP/L

button to point to “MANUAL

CLOCK SET”.

– SETTING CLOCK –

AUTO CLOCK

[ON]

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps [1] and [2].

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

Then, press the F.FWD/B button.

2)Select where you want to change using the

F.FWD/B or REW/s button.

3)Enter correct numbers using the PLAY/K or

STOP/L button.

4)Press the MENU button on the remote control to

start the clock.

– MANUAL CLOCK SET –

MONTH DAY YEAR

3 Select the month

Press the PLAY/K or STOP/L

button until your desired month

appears. (Example: May → 05)

Then, press the F.FWD/B button.

0 5

– – – – – – – – –

HOUR

– –

MINUTE

– – – –

PLEASE NOTE:

4 Select the day

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the F.FWD/B or REW/s button to turn [OFF]

this function. Then you can manually adjust the

clock.

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 6th → 06)

0 5

0 6 – – – – – – –

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

AUTOMATIC CLOCK SETTING

5 Select the year

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2004)

– MANUAL CLOCK SET –

MONTH DAY YEAR

Make sure ...

The TV/VCR is turned on.

Confirm the TV/VCR is receiving a RF (Radio

•

0 5

0 6 THU 2 0 0 4

HOUR

– –

MINUTE

– – – –

Frequency) signal from either an antenna or cable

system connection using the ANT. terminal on the

rear of the TV/VCR.

Then, press the F.FWD/B button.

NOTE:

6 Select the hour

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

– MANUAL CLOCK SET –

MONTH DAY YEAR

If a cable converter box is being used, make sure it

is powered on.

•

0 5

0 6 THU 2 0 0 4

You must use the TV/VCR remote control to per-

form the clock setting procedure.

•

HOUR

0 5

MINUTE

– – PM

Then, press the F.FWD/B button.

If the TV/VCR is connected directly to a cable

•

converter box or satellite box, the local PBS sta-

tion must be selected on the cable box itself, and

the TV/VCR must be set to the output channel of

the cable converter box or satellite box (usually

channel 3 or 4), to be able to set up or correct the

clock automatically.

7 Select the minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: 40)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 THU 2 0 0 4

HOUR

0 5

MINUTE

4 0 PM

- 11 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

5 Turn off the TV/VCR

Once the TV/VCR is turned off , it will periodically

check and set the correct date and time.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B button until

“AUTO CLOCK [ON]” appears.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

First Sunday of April : At 2 AM the clock imme-

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

3 Begin “AUTO CLOCK CH SEARCH”

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

Press the POWER button to turn on the TV/VCR.

•

Press the STOP/L button to select

– SETTING CLOCK –

“AUTO CLOCK CH SEARCH”.

AUTO CLOCK

AUTO CLOCK CH SEARCH

[ON]

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

Press the F.FWD/B button.

The TV/VCR is now searching

[OFF]

•

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

seconds per channel.

“_ _” appears at the lower left of

the screen when the search has

ended.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

– AUTO CLOCK CH SEARCH –

•

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

•

Then, press the F.FWD/B button.

_ _

station(s) in your area. See item 4 below.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on pages 10-11.

•

Press the PLAY/K or STOP/L but-

– SETTING CLOCK –

ton to point to “D.S.T.”.

Then, press the F.FWD/B or

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[ON]

REW/s button until [ON] appears.

Press the MENU button to exit the screen.

NOTE: During Auto Clock CH Search, the picture

may be distorted. This is normal.

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the MENU button on the

remote control.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

Press the STOP/L button to select

“AUTO CLOCK CH”.

Press the F.FWD/B or REW/s

buttons until you locate Auto

Clock Set station number. See item

3 above.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

F.FWD/B or REW/s button.

TIME SEARCH

– SETTING CLOCK –

AUTO CLOCK

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[

45]

[OFF]

Press the MENU button to exit the screen.

- 12 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

DELETING (OR ADDING)

CHANNEL

CHANNEL SET UP

You can program the tuner to scan all the channels

you receive in your area.

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

NOTE: Channel memory programming is NOT

needed when connected to a cable box or satellite

box. Just select the TV/VCR channel selector to the

output channel of the cable box or satellite box (Ex

CH3). Then select the channel to be viewed on the

Cable Box or Satellite Box.

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Make sure ...

Press the POWER button to turn on the TV/VCR.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

•

TIME SEARCH

Then, press the F.FWD/B button.

1 Select “CHANNEL SET UP”

Press the MENU button on the

– M E N U –

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

– CHANNEL SET UP –

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the F.FWD/B button.

Then, press the F.FWD/B button.

3 Enter the desired channel number

Press the PLAY/K or STOP/L but-

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it) (Example:

CH8)

2 Begin auto ch programming

Press the PLAY/K or STOP/L but-

ton to point to “AUTO CH PRO-

GRAMMING”.

Then, press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

ADD / DELETE

When selecting cable channels which are higher

than 99, press the +100 button first, then, press the

last two digits. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

You must proceed single-digit channel numbers

with a zero (Example: 02 ... 09).

•

3 After scanning

The tuner stops on the lowest memorized channel.

•

When AUTO CH PROGRAMMING is activated

•

where there is no TV signal input, “NO TV SIG-

NALS” will appear on the display after the com-

pletion of the channel scanning.

4 Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

The TV/VCR may display TV channels to be

CATV channels caused by poor antenna reception.

In this case, try auto ch programming again.

•

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

again, the channel is memorized again.

•

Added channel: Light blue.

Deleted channel: Light red.

5 Exit the channel setup mode

Press the MENU button on the remote control to

returns to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

- 13 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

3 Adjust sound

Press the VOLUME or button

to adjust the volume.

Press the MENU button on the

– M E N U –

TIMER PROGRAMMING

remote control.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to ”PICTURE CON-

TROL”.

VOLUME 20

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

GAME MODE

This function enables you to decrease the TV screen

contrast and making it suitable for use with a Video

game system.

NOTE: This function CANNOT be set during

recording.

2 Select item you want to adjust

Press the PLAY/K or STOP/L button until desired

control is displayed.

BRIGHT

CONTRAST

BRIGHT

COLOR

Press the GAME button on the

GAME

–

P +

TINT

SHARPNESS

remote control. “GAME” appears

on the screen.

When you press the GAME button;

3 Adjust the picture control

The TV/VCR turns on automatically.

The TV/VCR will select front A/V input mode

•

Press the F.FWD/B or REW/s button to adjust to

your desired level.

automatically.

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

Arrow Button

{

Arrow Button

ton on the remote control.

to decrease

brightness

to increase

brightness

BRIGHT

DEGAUSSING

to increase

contrast

to decrease

contrast

CONTRAST

This television has a degaussing circuit that will clear

up color errors on the TV screen that are caused by

any excess magnetism which happens to get too close

to the TV. This circuit is designed to operate once

when the set is first plugged in. If minor color errors

are seen in some locations on the screen, please

unplug the TV for approximately 15 minutes. When

the TV is plugged back in, the degaussing circuit will

operate once to clear them up. Repeat this procedure

any time the TV screen is accidentally magnetized, or

when the TV is moved or relocated.

to pale

to purple

to soft

to brilliant

to green

COLOR

TINT

to clear

SHAPNESS

If there is a power failure of any kind, the unit will

retain its setting.

•

- 14 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

WHEN THE CLOSED CAPTION MODE

IS ON

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news, pre-recorded tapes with either a dia-

logue caption or text display.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is usually

used for a second language if available.

The On-Screen Display will disappear after 5 sec-

onds.

This is also true when the MUTE button is pressed,

and when the PAUSE/STILL button is pressed

while recording.

•

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

V-CHIP SET UP

Make sure ...

NOTE:

TV/VCR is turned on.

You have the TV/VCR remote control.

•

Not all programs are broadcast with closed captions. Your

TVCR is designed to provide error free closed captions

from high quality antenna, cable and VCR signals.

Conversely, poor quality signals are likely to result in cap-

tion errors or no captions at all. Common signal conditions

which may cause captions errors are listed below:

•

1 Select “V-CHIP SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to select “V-CHIP SET UP”.

Then, press the F.FWD/B button.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Automobile ignition noise

Electric motor noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

•

TIME SEARCH

•

ghosts or airplane flutter.

2 Enter Access code

Use the numbers on the remote

control to enter the access code.

For the first time set-up or in the

event the TV/VCR has lost

ACCESS CODE

Playback of poorly recorded or worn VCR tapes.

If the TV/VCR displays a black box

on the TV screen, this means that the

TV/VCR is set to the TEXT mode.

To clear screen, select [CAPTION1],

[CAPTION2] or [OFF].

•

power, enter the default code of the numbers:

0000.

Make sure ...

– V-CHIP SET UP –

3 Select “TV RATING”

Press the PLAY/K or STOP/L but-

ton to select “TV RATING”.

TV/VCR power must be turned on.

•

TV RATING

MPAA RATING

CHANGE CODE

1 Select “CAPTION”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CAPTION”.

– M E N U –

Then, press the F.FWD/B button.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

4 Blocking TV programs

Press the PLAY/K or STOP/L but-

ton to select “TV rating” that you

wish to block.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

TIME SEARCH

(

)

(

– M E N U –

Select your desired caption menu

When you select the rating catego-

•

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Press the F.FWD/B or REW/s button

ry and turn it [BLOCK], the higher rating will turn

[BLOCK] automatically. Also, the lower rating will

turn [VIEW] automatically.

When you turn “TV-Y” to [VIEW], then all ratings

will turn to [VIEW] automatically.

until your desired caption menu appears.

([CAPTION1], [CAPTION2], [TEXT1]

or [TEXT2])

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

•

3 Exit the caption setting mode

Press the MENU button on the remote control to

return to TV mode.

Selection

TV-Y

TV-Y7

TV-G

TV-PG

TV-14

Rating Category Explanations

Appropriate for all children

Appropriate for children seven and older

General Audience

Parental Guidance suggested.

Unsuitable for children under 14

TO CANCEL THE CLOSED CAPTION SYSTEM

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Press the MENU but-

ton on the remote control to return to TV mode.

TV-MA Mature audience only

- 15 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING V-CHIP BLOCKED PRO-

GRAMMING

Note: To change the rating, the TV/VCR must be

turned to a station that is not protected. If the (PRO-

TECTED) appears on the screen, please change the

channel to a station that is not protected.

1)Follow steps [1] and [2].

2)Press the F.FWD/B button to select "TV RAT-

ING". Select a TV rating to be unblocked by press-

ing the PLAY/K or STOP/L button.

Then press the F.FWD/B button to unblock the

rating.

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to

enter the setting and exit the screen.

V-CHIP SET UP SUB RATINGS

When you select the ratings of TV-Y7,TV-PG,TV-14

or TV-MA you will have the option of selecting sub

rating categories.

– M E N U –

1 Select “V-CHIP SET UP”

TIMER PROGRAMMING

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to select “V-CHIP SET UP”.

Then, press the F.FWD/B button.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

3)Press the MENU button on the remote control to

exit the screen.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

MPAA RATING SET UP

– M E N U –

1 Select “V-CHIP SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

2 Enter Access code

Use the number buttons on the remote

SETTING CLOCK

Press the MENU button on the

ACCESS CODE

CHANNEL SET UP

USER’S SET UP

remote control.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

control to enter the access code

Press the PLAY/K or STOP/L but-

ton to select “V-CHIP SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

Note: Default code is 0000.

– V-CHIP SET UP –

3 Select “TV RATING”

Press the PLAY/K or STOP/L but-

ton to select “TV RATING”.

2 Enter Access code

Use the numbers on the remote

control to enter the access code.

ACCESS CODE

TV RATING

MPAA RATING

CHANGE CODE

Then, press the F.FWD/B button.

4 Selecting Sub-Ratings”

– V-CHIP SET UP –

3 Select “MPAA RATING”

TV RATING

MPAA RATING

CHANGE CODE

Press the STOP/L button to select the sub-rating you

Press the PLAY/K or STOP/L but-

ton to point to “MPAA RATING”.

Then, press the F.FWD/B button.

wish to block. Then, press the F.FWD/B button.

When you select [TV-Y7]:

Press the STOP/L or PLAY/K

button to select “FV” (Fantasy

Violence).

Then, press the F.FWD/B button

to select [BLOCK] or [VIEW].

When you select [TV-PG], [TV-14] or [TV-MA]:

•

TV–Y7

[BLOCK]

4 Select your desired item

Press the PLAY/K or STOP/L but-

ton to point to your desired item.

Then, press the F.FWD/B button to

select [BLOCK] or [VIEW].

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

•

Press the STOP/L or PLAY/K

button to select “D”(Suggestive

Dialog), “L”(Coarse Language),

“S”(Sexual Situation), or

TV–PG

[BLOCK]

Selection

PG-13

Rating Category Explanations

General Audience

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

[BLOCK]

“V”(Violence). Then, press the

F.FWD/B button to select [BLOCK] or [VIEW].

Note: When you select [TV-MA], “D” does not

appear on the TV screen.

The sub-ratings which set to

[BLOCK] appears next to the rat-

ing category in the TV rating

menu.

NC-17

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

[BLOCK]

Mature audience only

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “G” to [VIEW], then all ratings

will turn to [VIEW] automatically.

•

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to

enter the setting and exit the screen.

- 16 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to

enter the setting and exit the screen.

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to exit

the screen.

Note: If you unplug the power code or power failure

occurs, the changed access code will be lost and will

return to default (0000). Change your access code

again as necessary.

CHANGE ACCESS CODE

To change access code, follow the steps.

1 Select “V-CHIP SET UP”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to select “V-

CHIP SET UP”.

Then, press the F.FWD/B button.

2 Enter Access code

ACCESS CODE

Use the number on the remote con-

trol to enter the access code.

Note: The default code is 0000.

– V-CHIP SET UP –

3 Select “CHANGE CODE”

Press the PLAY/K or STOP/L but-

ton to select "CHANGE CODE".

Then, press the F.FWD/B button.

TV RATING

MPAA RATING

CHANGE CODE

4 Enter New code

Use the number buttons to enter

your desired access code in the

NEW CODE space. Then enter

the same code in the CONFIRM

CODE space. V-CHIP SET UP

screen appear on the screen.

NEW CODE

X X X X

CONFIRM CODE

If you enter wrong code, repeat step 4, making

sure you enter the same new code exactly in the

confirm code space.

•

PLAYBACK

This TV/VCR will operate with any cassette that has the

mark. For best results, we

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

INSERTING A CASSETTE

PRECAUTIONS

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR. The

TV/VCR will automatically turn on.

Avoid moisture. Moisture condensation may occur

•

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields from speaker systems.

Window

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

- 17 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CANCEL THE REPEAT PLAY MODE

NORMAL PLAYBACK

Make sure ...

TV/VCR power must be turned on.

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

•

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

PICTURE SEARCH

2 To begin playback

Press the PLAY/K button.

PLAY

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback (in the

SP / LP / SLP modes).

2)Press it again and the TV/VCR will now search in

super high speed (in the LP / SLP modes only).

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY/K button to return to normal

speed.

Note: If any menu is activated on

the screen, the PLAY/K button does

not function. Press the MENU but-

ton to clear the menu, then press the PLAY/K button.

3 To stop playback

Press the STOP/L button when playback is complet-

ed.

AUTO REPEAT PLAYBACK

The TV/VCR has an auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part of more than 10 seconds.

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

1 Select “USER’S SET UP”

– M E N U –

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point from which you want to review.

USER’S SET UP

–

2 Select “ALL” or “BLANK”

Press the PLAY/K or STOP/L but-

ton to point to “REPEAT PLAY”.

Press the F.FWD/B or REW/s

button repeatedly until your desired

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

3 Begin recording or playback

Press the RECORD or PLAY/K button.

Press the STOP/L button when recording or play-

back is completed.

selection [ALL] or [BLANK] appears.

3 Exit the Repeat Play setting

Press the MENU button on the remote control to

return to the TV mode.

4 To activate “ZERO RETURN” mode

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “ZERO RETURN”.

SETTING CLOCK

4 Start playback

Press the PLAY/K button to start the Repeat Play.

”REPEAT PLAY B” appears.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

•

The counter will appear on the TV screen.

The tape will automatically stop when the counter

returns to 0:00:00.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

- 18 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TIME SEARCH

RENTAL PLAYBACK

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply by

entering the exact amount of playback time you want

to skip.

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

NOTES:

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

This function will not operate in recording mode.

In the example below: To watch a program that is 2

hours, 50 minutes from the present tape position, in

either direction.

1 Select “USER’S SET UP”

•

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

remote control.

•

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

1 Insert a tape.

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

TIME SEARCH

2 : 50

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button

(with each push it will increase by

10 minutes).

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

3 Enter your desired time

Press the PLAY/K or STOP/L button until your

desired time appears. (Example: “2:50” stands for 2

hours 50 minutes)

If you wish to cancel the Time Search at this point,

press the MENU button on the remote control.

4 Start playback

Press the PLAY/K button to start playback.

“RENTAL PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR.

•

4 Begin Time Search

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will remember the setting.

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/VCR or the

remote control. This will delete the selected time.

NOISE CANCEL (in the Still mode)

This feature allows you to reposition or reduce the

noise lines of a still picture. Press the PAUSE/STILL

button so that the noise lines change position on the

screen so you can see the picture in its entirety with-

out distracting noise lines.

NOTE: This feature can be activated ONLY when

viewing a tape recorded in the SLP mode. If the tape

was originally recorded in the SP or LP mode, the

still picture may revert to black and white in addition

to the “noise bars”. This is normal.

- 19 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

This is not a fault of the machine, but is a by-

product of the technology involved in producing

a TV/VCR with 2 video heads.

If it is left in the Still mode for more than five

minutes, the TV/VCR will automatically switch to

the Stop mode.

VERTICAL HOLD CONTROL

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

•

NOTE:

If there are video noise lines on the screen, see Tracking

Adjustment section.

TRACKING ADJUSTMENT

STILL PICTURE

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines. Press

the PLAY/K button to return to playback.

NOTES:

Usually there will be video “noise” lines (black

and white streaks or dots) on the screen. This is

normal.

However when playing pre-recorded tapes or tapes

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

•

If the tape was originally recorded in SP or LP

mode, the still picture will be black and white in

addition to the “noise” lines.

RECORDING

Make sure ...

Before recording, make sure:

TV/VCR power is turned on.

•

The desired channel is selected by pressing the num-

ber buttons on the remote control or the CHANNEL

Up/Down button. (If the TV/VCR is connected to a

cable box or satellite box, the TV/VCR must be on

CH3 or CH4, then the channel to be recorded is

selected on the cable box or satellite box. )

There is a tape with its safety tab into the VCR.

The desired recording speed is selected in SP(stan-

dard play) or SLP(super long play) mode by press-

ing the SPEED button on the remote control.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

NOTE: This unit will ONLY record and view the

same channel.

NORMAL RECORDING

1)Begin the recording by pressing the RECORD but-

ton.

To temporarily stop recording or resume it, press

the PAUSE/STILL button. After the TV/VCR has

been in Pause mode for 5 minutes, it will stop

automatically to protect the tape and the video

head.

Tape Speed

Recording/Playback Time

T120 T160

Type of tape T60

SP mode

1 hour

3 hours

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

ERASE PREVENTION

NOTES:

You can prevent acciden-

tal erasing of recording

by breaking off the tab

on the back edge of the

cassette.

If you decide to record

on the tape again, cover

the hole with plastic

tape.

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape

damage.

•

If “CLOSED CAPTION (ON)” is selected, the

On-Screen Display will appear for 5 seconds, then

disappear.

•

2)Stop the recording by pressing the STOP button

when recording is completed.

Tab

Plastic Tape

- 20 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

Avoid overlap of programs ...

There is a chance that a program will not be record-

ed. When programs overlap:

OTR (One Touch Recording)

This function enables you to set the recording length

simply by pressing the REC/OTR button on the

TV/VCR.

The program with the earliest start time will record

first.

•

Once the earliest program finishes recording, the

overlapping programs will record in the order of

the program number.

The illustration below demonstrates the sequence

of recording.

•

1)Begin OTR by pressing the

REC/OTR button on the

TV/VCR repeatedly until the

desired recording length appears.

Recording stops when 0:00 is

OTR(2 : 30)

•

reached.

Recording Sequence

NOTES:

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

This function CANNOT be done from the remote

•

control.

9:30AM-12:00PM

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

•

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, eject the tape and turn itself off.

•

1 Select “TIMER PROGRAMMING”

If you press the power button during OTR, the TV

monitor turns off. But the recording continues until

the selected length is reached.

•

Press the MENU button on the remote control.

– M E N U –

Confirm “TIMER PROGRAM-

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

MING” is pointed to by pressing

the PLAY/K button.

Press the F.FWD/B button.

Push(es) Display

1 push

Recording length

(continuous recording)

30 minutes

ZERO RETURN

TIME SEARCH

If you have not yet set the clock,

•

2 pushes

3 pushes

4 pushes

0:30

1:00

1:30

“MANUAL CLOCK SET” appears. If so, follow

steps [3] to [8] on page 11. Then set the timer

recording.

60 minutes

90 minutes

17 pushes

8:00

480 minutes

2 Select your desired program position (1~8)

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L but-

CH DATE

BEGIN END

ton to select the desired program

position.

Then, press the F.FWD/B button.

TIMER RECORDING

- - -/- - - - - -:- -

-:- - - -

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

In the example below, the timer is being set to record:

July 4th, 2004

SETTING TIME: from 7:30PM to 8:50PM

3 Set the channel number

Press the PLAY/K or STOP/L but-

ton until the desired channel num-

ber appears.

(Example: CH61)

Then, press the F.FWD/B button.

Remember:

If your TV/VCR is connected to a cable or satellite

box, you must set the TV/VCR to channel 3 or 4 to

match the output channel of the box. Then, select

CH61 on the cable or satellite box.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

DATE:

CHANNEL:

TAPE SPEED:

CH61

Make sure ...

If your TV/VCR is connected to a cable or satellite

box, you must set the TV/VCR to channel 3 or 4 to

match the output channel of the box.

Clock is set to the correct time and date before set-

ting the timer.

TV/VCR power is turned on to program it.

To insert a cassette tape with its erase prevention

tab in place. (If necessary, rewind or fast forward

the tape to the point at which you want to begin

recording.)

•

4 Select once, every day or

– TIMER PROGRAMMING –

•

CH DATE

BEGIN END

weekly recording

For once recording :

- - -/- - - - - -:- -

61 7/04 SUN -:- -

- - -/- - - - - -:- -

-:- - - -

Press the PLAY/K (up) button

until the desired date appears.

The channel you want to record is properly set in

advance.

(Example: “7/04” for July 4th). Then, press the

F.FWD/B button.

•

- 21 -

Download from Www.Somanuals.com. All Manuals Search And Download.

9I03

For every day recording : To record a TV program at

the same time on the same channel every day.

(Example: Monday through Sunday)

10 Set the timer

Press the POWER button to set automatic timer

recording. The RECORD indicator lights up.

Press the STOP/L (down) button

until “EVRY DAY” appears.

Then, press the F.FWD/B but-

ton.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

You must turn off the TV/VCR to activate automat-

ic timer recording.

•

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

For weekly recording : To record a TV program at

the same time on the same channel every week.

(Example: every Monday)

– TIMER PROGRAMMING –

Press the STOP/L (down) button

TIMER PROGRAM EXTENSION

CH DATE

BEGIN END

until “EVRY” and your desired

day of the week appear together.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

2)Repeat step [1] on page 21.

– TIMER PROGRAMMING –

CH DATE BEGIN END

3)Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automat-

ically be set to the SLP mode.

5)Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

5 Set beginning hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “ 7, PM” for 7:30PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/04 SUN 7:12^P

- - -/- - - - - -:- -

– TIMER PROGRAMMING –

CH DATE BEGIN END

6 Set beginning minute

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “30” for 7:30PM)

- - -/- - - - - -:- -

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

7 Set end hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

8:30^P

- -

-:- - - -

TO CORRECT A PROGRAM

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

bers using the PLAY/K or STOP/L button.

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “50” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

After setting a program;

1)Press the POWER button.

•

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

2)Repeat steps [1] - [2] on page 21.

3)Press the F.FWD/B button (or press the REW/s

button to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the PLAY/K or STOP/L but-

ton.

– TIMER PROGRAMMING –

CH DATE BEGIN END

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

4)Press the POWER button to set automatic timer

recording.

Then, press the F.FWD/B button.

The program is now completed.

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control

to return to original mode.

•

- 22 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears. Then,

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

After setting a program;

1)Press the POWER button.

•

2)Repeat steps [1] ~ [2] under TIMER RECORD-

ING, page 21, and select a program you want to

cancel.

3)Press the T-PROG. CLEAR button.

4)Press the MENU button on the remote control to

return to TV mode.

press the MENU button on the remote control to

return to TV mode.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/VCR will rewind to the beginning of the recorded

While recording is in progress;

1)Press POWER button.

•

program(s).

NOTE:

2)Press the STOP/EJECT button on the TV/VCR.

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

•

2)Press the MENU button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed

to.

4 Watch the recorded program

Press the PLAY/K button.

4)Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

5)Press the MENU button on the remote control to

return to TV mode.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Then, press the MENU

button on the remote control to return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

HINTS FOR AUTOMATIC

TIMER RECORDING

Make sure the channel you want to record is prop-

erly set in advance.

•

WAKE UP TIMER

It is not necessary to press the RECORD button for

•

timer recording.

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

•

NOTES:

•

Use the remote control for this procedure.

Clock must be set to the correct time before setting

•

the timer.

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, and the tape will be ejected.

•

1 Select “WAKE UP TIMER”

Press the WAKE-UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s

button until [ON] appears.

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

WAKE UP B ON/OFF

[ON]

TIMER

TV/TAPE

TIME

[TV]

[12:00AM]

– M E N U –

1 Select “USER’S SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

- 23 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

SLEEP TIMER

2 Select “TV” or “TAPE”

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

Press the PLAY/K or STOP/L but-

ton until it points to “TV/TAPE”.

Press the F.FWD/B or REW/s

button, and select [TV] or [TAPE].

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

[TV]

NOTE:

[12:00AM]

This function does not operate during Recording

•

mode.

3 Set wake up time

1 Select “SLEEP TIMER”

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

Press the PLAY/K or STOP/L but-

ton until it points to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

WAKE UP

TIMER

ON/OFF

TV/TAPE

B TIME

[ON]

[TV]

[12:00AM]

2 Set sleep time

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

your desired sleep time appears.

Each additional push will increase (or decrease) the

time by 10 minutes.

SLEEP TIMER [2:00]

Each additional push will increase

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

the time by 30 minutes up to 120 minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE WAKE UP TIMER

TO CANCEL THE SLEEP TIMER

Press the WAKE-UP/SLEEP button on the remote

control once, and confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s button until [OFF]

appears.

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer, press the

WAKE-UP/SLEEP button twice, then press the

MENU button on the remote control to exit the sleep

timer setting.

COPYING A VIDEO TAPE

You can make copies of video tapes made by friends

or relatives for your enjoyment.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record into the TV/VCR’s cassette compartment.

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

4)Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

NOTE: “AUX” is found below the lowest numbered

memorized channel. (Example: CH2)

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

VIDEO

AUDIO

[TV/VCR]

5)Press the RECORD button on the TV/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during copying, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

[Ex: Source (playing)

VCR or camcorder]

7)To stop copying, press STOP/EJECT button on the

TV/VCR, then stop the tape on the source VCR or

camcorder.

Audio/Video

patch cord

(not supplied)

AUDIO

OUT

VIDEO

- 24 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

WHEN THE CLOSED CAPTION MODE IS OFF:

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

5:40PM

CH2

Press

once

Press

once

COUNT 0:12:34

Press once

OFF mode

Clock/Counter mode

WHEN THE CLOSED CAPTION MODE IS ON:

The On Screen Display disappears after 5 seconds.

•

STOP

5:40 PM

CH2

This is true even if the MUTE button is pressed, or the

PAUSE/STILL button is pressed while recording.

COUNT 0:12:34

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

•

hours, minutes, and seconds. (The displayed time

will not change on a blank tape or blank portions on

the tape.)The “–” indication will appear when the

tape has rewound further than “0:00:00” on the tape

counter.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

MAINTENANCE

back, the video heads in your TV/VCR may need

to be cleaned.

CABINET CLEANING

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

1.Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-488-1222, to

locate an Authorized Service Center.

NOTES:

Remember to read the instructions included with

the video head cleaner before use.

Clean video heads only when problems occur.

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

•

AUTO HEAD CLEANING

•

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

SERVICING

Should your TV/VCR become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

488-1222, to locate an Authorized Service Center.

Playback picture may become blurred or interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

- 25 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Program TV channels into TV/VCR.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR clock is set correctly.

Make sure the video tape has an erase-prevention tab in place. If the

tab has been removed, please cover the open space with tape.

Adjust tracking control for a better picture using the CHANNEL

or L button on the TV/VCR.

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 25.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

Magnetism from nearby appliances or unshielded stereo speakers or

geomagnetism might affect the color of the TV picture. Refer to

“DEGAUSSING” on page 14.

No power.

•

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

•

Timer recording is not possible.

Cannot go into Record mode.

•

Playback picture is partially noisy.

•

No picture but the audio is OK for

tape playback.

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

•

Different color marks on screen.

•

CLOSED CAPTION PROBLEM

My TV/VCR is showing captions

that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

- 26 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

13 inch in-line gun, 90˚

deflection tube

NTSC-M

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Closed caption system :§15.119/FCC

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary two-head

1/2 inch

OTHER SPECIFICATIONS

Power requirement : AC 120V/60Hz

Power consumption : 60W

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

Dimensions :

H:15-5/16” (389mm)

W:14-7/16” (367mm)

D:14-7/8” (377mm)

23.1 lbs (10.5kg)

#2~#6

#7~#13

#14~#69

Weight :

Designs and specifications are subject to change

without notice and without our legal obligation.

If there is a discrepancy between languages, the

default language will be English.

•

VHF :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Antenna input :

VHF/UHF 75 ohms

unbalanced

Video input :

Audio input :

Earphone :

RCA connector [ 1

1/8” monaural (3.5 mm)

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 27 -

9I03

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

- PANEL DELANTERO -

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

EARPHONE

1 2 3 4 5 6 7 8 910 11 12 1314

4 Botones de volumen (VOLUME X/ Y)–

Ajustan el nivel del volumen.

- CONTROL REMOTO -

5 Botones de canales (CHANNEL K/ L)–

Púlselos para seleccionar los canales deseados para

ver o grabar.

Se puede mostrar el menú principal en la pantalla del

televisor pulsando repetidamente este botón del tele-

visor/videograbadora.

Función de seguimiento– Pulse los botones

para minimizar el ruido de vídeo (líneas o puntos en

la pantalla) durante la reproducción.

6 Ventanilla sensora del mando a distancia–

Recibe las señales infrarrojas procedentes del

mando a distancia.

WAKE-UP

/SLEEP

POWER

EJECT

CHANNEL

RETURN

CHANNEL

VOLUME

+100

DISPLAY

MUTE

7 [ Televisor/videograbadora ]

Botón de parada/expulsión (STOP/EJECT)–

Púlselo para detener la cinta. Púlselo en el modo

de parada para expulsar la cinta del

televisor/videograbadora.

PLAY

REW

F.FWD

STOP

SPEED PAUSE/STILL

RECORD

[ Control remoto ]

T-PROG.

CLEAR

GAME

Botón de explusión (EJECT)– Púlselo para

expulsar la cinta del televisor/videograbadora.

Botón L–

Púlselo para seleccionar los modos de ajuste

•

desde el menúde la pantalla.

TIME SEARCH

COUNTER

RESET

Púlselo para introducir dígitos cuando establez-

ca un programa.

(Por ejemplo: Para ajustar el reloj o establecer un

programa de temporizador)

8 Botón de rebobinado (REW)– Púlselo para

rebobinar la cinta, o para ver la imagen en retroceso

rápido durante el modo de reproducción. (Búsqueda

con rebobinado)

•

1 Toma de entrada de vídeo (VIDEO)–

Conéctela a la toma de salida de vídeo de su

videocámara u otra videograbadora.

2 Toma de entrada de audio (AUDIO)–

Conéctela a la toma de salida de audio de su equipo

de audio, videocámara u otra videograbadora.

3 Botón de la alimentación (POWER)– Púlselo

para encender y apagar el televisor/videograbadora.

Púlselo para activar la grabación con temporizador.

Botón s–

Púlselo para seleccionar un modo desde un menú

particular.

•

(Por ejemplo: IDIOMA o ADJUST DE USER)

- 28 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

- PANEL TRASERO -

ANT.

9 Botón de reproducción (PLAY)– Púlselo para

iniciar la reproducción.

Botón K–

16 Botón de menú (MENU)– Púlselo para visu-

alizar el menúprincipal en la pantalla del televisor.

17 Botón del visualizador (DISPLAY)– Visualiza

el contador o el número del canal actual y la hora

actual en la pantalla del televisor.

Púlselo para seleccionar los modos de ajuste

desde el menú de la pantalla.

•

18 Botón de velocidad de cinta (SPEED)–

Púlselo para elegir la velocidad de grabación desea-

da: SP/SLP.

19 Botón T-PROG. CLEAR– Púlselo para cancelar

un programa de temporizador.

Púlselo para introducir dígitos cuando establezca

un programa.

(Por ejemplo: Para ajustar el reloj o establecer un

programa de temporizador)

•

10 Botón de avance rápido (F.FWD)– Púlselo

para avanzar rápidamente la cinta, o para ver la

imagen en avance rápido durante el modo de repro-

ducción. (Búsqueda con avance rápido)

Botón B–

Botón de reposición del contador

(COUNTER RESET)– Púlselo para reponer el

contador a 0:00:00.

20 Botón de juego (GAME)– Establece el modo del

juego y el modo de entrada externa al mismo tiem-

po.

21 Botón de búsqueda con tiempo (TIME-

SEARCH)– Púlselo para activar el modo de

búsqueda con tiempo.

22 Botón de pausa/imagen fija (PAUSE/STILL)–

Púlselo para detener temporalmente la cinta durante

la grabación o para ver una imagen fija durante la

reproducción.

23 Botón de silenciamiento (MUTE)– Silencia el

sonido. Púlselo de nuevo para recuperar el sonido.

24 Botón de retorno de canal (CHANNEL

RETURN)– Púlselo para volver al canal anterior.

Por ejemplo, pulsando una vez este botón, la visual-

ización del canal cambiará de 3 (canal actual) a 10

(canal anterior), y al pulsarlo por segunda vez, el

canal cambiará del 10 al 3.

Cuando establezca un programa (por ejemplo: para

ajustar el reloj o para establecer un programa de

temporizador), púlselo para determinar su elección

y vaya al paso siguiente que quiera introducir.

Púlselo para determinar los modos de ajuste

desde el menúde la pantalla.

•

Púlselo para seleccionar un modo desde un

menúparticular.

(Por ejemplo: IDIOMA o ADJUST DE USER)

11 Botón de grabación (REC)– Púlselo para ini-

ciar la grabación manual.

Botón de grabación de un toque (OTR)–

Activa la grabación de un toque. (Sólo en el televi-

sor/videograbadora)

12 Indicador de grabación (RECORD)– Parpadea

durante la grabación.

Se enciende en el modo de espera de la grabación

con temporizador.

13 Toma de auriculares (EARPHONE)– Para

conectar los auriculares (no suministrados) y

escuchar en privado. La toma es mono y tiene un

tamaño de 1/8”(3.5 mm).

14 Compartimiento del videocasete

15 Botones numerados– Púlselos para seleccionar

los canales deseados para ver o grabar. Para selec-

cionar canales del 1 al 9, pulse primero el botón 0 y

luego el botón 1 a 9.

25 Botón del temporizador despertador/para

dormir (WAKE-UP/SLEEP)– Ajusta el tempo-

rizador para despertarse/dormir.

26 Terminal de antena (ANT.)– Para conectar una

antena o sistema de televisión por cable.

27 Cordón de alimentación– Conéctelo a la toma

de CA estándar (120V/60Hz).

Botón +100– Cuando seleccione canales de tele-

visión por cable cuyo número sea superior al 99,

pulse primero este botón, y luego pulse los dos últi-

mos dígitos. (Para seleccionar el canal 125, pulse

primero el botón “+100” y luego el “2” y el “5”.)

- 29 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIONES DE ANTENA/CABLE

Desde el cable coaxial o

Antena combinada de

VHF/UHF

(no incluído)

caja de emisiones vía

satélite de 75 ohm del

sistema de Cable

Caja de CATV

o caja de emi-

siones vía satélite

(no incluído)

Antena de varilla UHF/VHF

(incluído)

OUT

Antena VHF

(no incluído)

Antena UHF

(no incluído)

Desde el

sistema de Cable

ANT.

Combinador de

VHF/UHF

(no incluído)

ANT.

Cable coaxial

de 75 ohm (no incluído)

Cable bifilar plano

MODO DE ENTRADA EXTERNA

– M E N U –

2 Seleccione “LANGUAGE”

Pulse el botón MENU en el mando

a distancia.

Pulse el botón PLAY/K o STOP/L

para señalar “LANGUAGE”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los cables

de salida de audio/vídeo del equipo de reproducción a

las tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón

CHANNEL K o L hasta que “AUX” aparezca en la

pantalla.

ZERO RETURN

TIME SEARCH

Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”

Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS” con el botón F.FWD/B y pulse el

botón REW/s en el mando a distancia.

Usted puede programar el temporizador para que explore

todos los canales que puedan recibirse en su zona.

SELECCION DE IDIOMA

4 Salga del modo de idioma

Pulse el botón MENU en el mando a distancia para

volver al modo del televisor.

1 Enchufe el cordón de alimentación

del televisor/videograbadora

Enchufe el cordón de alimentación del

televisor/videograbadora en una toma de

CA estándar.

NOTA: Si, por alguna razón, el menú está en español

o francés, pulse el botón MENU en el mando a dis-

tancia, pulse el botón PLAY/K para señalar el

“IDIOMA (ESPAÑOL)” o “LANGAGE

(FRANÇAIS)”, a continuación, pulse el botón

F.FWD/B y pulse el botón MENU en el mando a

distancia.

NOTA:

Si aparecen algunas cifras en la esquina

de la pantalla, pulse el botón POWER sin desench-

ufar el cordón de alimentación.

•

Asegúrese de que ...

Pulse el botón POWER para encender el televi-

sor/videograbadora.

•

NOTA: Esta función afecta sólo el idioma en el

menú de la pantalla y no la fuente de audio.

- 30 -

0I29

Download from Www.Somanuals.com. All Manuals Search And Download.

AJUSTE DE CANAL

AJUSTE DEL RELOJ

Puede programar el sintonizador para buscar todos

los canales que recibe en su localidad.

Cerciórese...

La alimentación del televisor/videograbadora

deberá estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 6 de mayo de 2004

HORA: 5:40 PM

1)Pulse el botón MENU en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”.

Luego, pulse el botón F.FWD/B.

2)Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”.

•

NOTA: El canal preparado NO es necesario cuando

esté conectado a una caja de cable o caja de satélite.

Sólo tiene que seleccionar con el selector de canal

del televisor/videograbadora al canal de salida de la

caja de cabe o caja de satélite (por ejemplo el canal

CH3). Seleccione el canal a ver en la caja de cable o

caja de satélite.

Asegúrese de que ...

Pulse el botón POWER para encender el televi-

sor/videograbadora.

•

Luego, pulse el botón F.FWD/B.

3)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el mes deseado. (Ejemplo: Mayo - 05)

Luego, pulse el botón F.FWD/B.

4)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el día del mes deseado. (Ejemplo: 6 - 06)

Luego, pulse el botón F.FWD/B.

1 Seleccione “AJUSTE DE CANAL”

Pulse el botón MENU en el mando

– M E N U –

COMO PROGRAMAR

CONTROL DE IMAGEN

AJUSTE RELOJ

AJUSTE DE CANAL

AJUSTE DE USER

AJUSTE DE V-CHIP

IDIOMA [ESPAÑOL]`

TITULO [OFF]

a distancia.

Pulse el botón PLAY/K o el botón

STOP/L para señalar “AJUSTE DE

CANAL”.

RETORNO A CERO

BUSQUEDA DE HORA

A continuación, pulse el botón

F.FWD/B.

5)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el año deseado. (Ejemplo: 2004)

Luego, pulse el botón F.FWD/B.

6)Pulse el botón PLAY/K o STOP/L hasta que

aparezca la hora deseada. (Ejemplo: 5, PM)

Luego, pulse el botón F.FWD/B.

7)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el minuto deseado. (Ejemplo: 40)

8)Pulse el botón MENU en el mando a distancia.

Aunque los segundos no se visualizan, éstos

empiezan a contar desde 00 cuando se pulsa

MENU en el mando a distancia. Utilice esta fun-

ción para sincronizar el reloj con la hora correcta.

2 Empiece el prefijado automático

Pulse el botón PLAY/K o STOP/L

para señalar “AUTOPROGRAMA-

CION DE CA”.

A continuación, pulse el botón

F.FWD/B.

AJUSTE DE CANAL

–

AGREGAR/BORRAR (CATV)

B AUTOPROGRAMACION DE CA.

El sintonizador busca y memoriza todos los canales

activos en su localidad.

3 Después de buscar

El sintonizador se detiene en el canal memorizado

más bajo.

Cuando se activa AUTOPROGRAMACION DE

•

CA, donde no hay entrada de señal del televisor,

aparecerá “NO HAY SEÑAL DE TV” en la pan-

talla después de terminar la búsqueda de canales.

El televisor/videograbadora puede reconocer los

•

canales de TV para que sean canales de TV de

antena de cable con las condiciones de recepción.

En este caso, pruebe nuevamente con el prefijado

automático en las condiciones de recepción fina.

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Get it fixed, at your home or ours!

Your Home

For repair in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME ^R(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com

www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Center.

1-800-488-1222

Call anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.)

1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

Au Canada pour service en français:

1-800-LE-FOYER^MC

1-888-SU-HOGAR^SM

(1-800-533-6937)

www.sears.ca

(1-888-784-6427)

Registered Trademark / ^TMTrademark / ^SMService Mark of Sears, Roebuck and Co.

Marca Registrada / ^TMMarca de Fábrica / ^SMMarca de Servicio de Sears, Roebuck and Co.

^MCMarque de commerce / ^MDMarque déposée de Sears, Roebuck and Co.

LIMITED 90 DAY WARRANTY

If this (product) experiences any failure due to a defect in material or workmanship within 90 days

from the date of purchase, return it to your nearest Sears store, and it will be replaced free of

charge.

This warranty applies only if this (product) is used for private household purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

Sears Roebuck and Co., Dept. 817WA Hoffman Estates, IL 60179

For the location of a Sears Service Center in your area : 1-800-488-1222

Printed in Malaysia

0EMN02520

★★★★★

Download from Www.Somanuals.com. All Manuals Search And Download.

T5508UJ

Sharp Cash Register XE A401 User Manual
Sharp Projector 68 409 01 User Manual
Snapper Camcorder 216518B User Manual
Snapper Snow Blower MS3419 User Manual
Sony Car Stereo System Car Audio User Manual
Sony Cassette Player WM FX221 User Manual
Sony Microcassette Recorder TCM 465 User Manual
Sony Projection Television KDF 55XS955 User Manual
StarTechcom Switch SV231UADVI User Manual
Talk electronic CD Player 22 User Manual