Sylvania TV VCR Combo SRC2213B User Manual

OWNER’S

MANUAL

COLOR TV/VCR

SRC2213B

SRC2319

13” MODEL ILLUSTRATED

This Owner’s Manual is made of

recycled paper.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1-800-968-3429.

energy efficiency. ENERGY STAR^®is

a U.S. registered mark.

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/VCR to its normal operation.

14.Lightning-For added protection for this TV/VCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/VCR due to lightning and

power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR, ask the service technician to perform routine

safety checks to determine that the TV/VCR is in proper

operating condition.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/VCR.

22.Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

- 3 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

ature differences are extreme.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

•

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore when the condensation occurs

inside the unit, turn the POWER button on and allow

at least 2 hours for the unit to dry out.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

_{Download from Www.Somanuals.c}-_om4_.-_{All Manuals Search And Download.}

1K09

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .17

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .19

PICTURE CONTROLS . . . . . . . . . . . . . . . . . .19

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C OPERATING CONTROLS AND FUNCTIONS 7

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20

NORMAL RECORDING . . . . . . . . . . . . . . . . .20

SKIPPING UNWANTED SCENES DURING

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20

OTR (One Touch Recording) . . . . . . . . . . . . . .20

TIMER RECORDING . . . . . . . . . . . . . . . . . . .21

TIMER PROGRAM EXTENSION . . . . . . . . .22

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

ANTENNA/CABLE CONNECTIONS . . . . . . .9

INSTALLING THE BATTERIES . . . . . . . . . . .10

EXTERNAL INPUT MODE . . . . . . . . . . . . . .10

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10

CHANNEL SET UP FOR THE FIRST TIME .10

CLOCK SET UP (AUTO / MANUAL) . . . . . .11

CHANNEL SET UP AGAIN . . . . . . . . . . . . . .12

DELETING (OR ADDING) CHANNEL . . . . .12

SELECTING THE LANGUAGE . . . . . . . . . . .13

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24

C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25

REAL TIME TAPE COUNTER . . . . . . . . . . . .25

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14

WATCHING A TV PROGRAM . . . . . . . . . . . .14

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14

CLOSED CAPTION SYSTEM . . . . . . . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25

C TROUBLESHOOTING GUIDE . . . . . . . . . . .26

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27

C CABLE CHANNEL DESIGNATIONS . . . . . .27

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

INDICE

CONTROLES DE OPERACIÓN Y

INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28

PREPARACIÓN DE CANALES POR

CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31

MODO DE ENTRADA EXTERNA . . . . . . . . . . .30 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

- 5 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

Infrared remote control

Bilingual on screen menu display selectable in

English or Spanish

Zero Return–The tape returns to counter of

•

0:00:00 by rewinding or fast forwarding.

Still–“Freeze” the picture at any time, for close

viewing of a particular scene. Only tapes recorded

in SLP mode will show a fairly clear picture.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Let you set the TV/VCR to advance

the tape by entering the desired playback time you

want to skip.

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts, and the Weekly timer allows recording to be

made once a week up to the end of the tape.

Real time counter–This shows the elapsed record-

ing or playback time in hours, minutes, and sec-

onds. The “–” indication will appear when the tape

is rewound further than the tape counter position

“0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

function from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Game mode–Automatically sets external input

mode and allows TV/VCR display to be suitable

for use with TV games.

Auto power on and off system–Automatically

turns on the TV/VCR when you insert the cassette,

turns off after auto-rewind, and ejects when the

beginning of the tape is reached.

•

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the record-

ing.

Wake up/Sleep timer–Allows you to have the

TV/VCR automatically turn on or off at a desired

time.

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

SUPPLIED ACCESSORIES

Remote Control Unit

2 AA Batteries

Rod Antenna

(13” model only)

PART NO. (0EMN00673 or

PART NO. (N0154UD)

0EMN01599 or

0EMN01755)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

_{Download from Www.Somanuals.c}-_om6_.-_{All Manuals Search And Download.}

1K09

OPERATING CONTROLS AND FUNCTIONS

This manual covers 13 and 19 . The operation of the two models are exactly the same except

the appearance. 13 model is illustrated in this manual.

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

- TV/VCR FRONT PANEL - [Fig.1]

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

EARPHONE

1 2 3 4 5 6 7 8 910 11 12 1314

1 VIDEO input jack– Connect to the video output

- REMOTE CONTROL - [Fig.2]

jack of your video camera or another VCR.

2 AUDIO input jack– Connect to the audio output

jack of your audio equipment, video camera or

another VCR.

WAKE-UP

/SLEEP

POWER

EJECT

3 POWER button– Press to turn TV/VCR on and

off. Press to activate timer recording.

X Y

CHANNEL

RETURN

4 VOLUME

level.

buttons– Adjust the volume

5 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording.

You may display the main menu on the TV screen

by pressing repeatedly this button on the

TV/VCR.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback

mode. (See page 19.)

6 Remote Sensor Window– Receives the infrared

signals from the remote control.

7 STOP / EJECT button (TV/VCR)– Press to stop

the tape motion. Press in the Stop mode to remove

tape from TV/VCR.

CHANNEL

VOLUME

+100

DISPLAY

MUTE

PLAY

REW

F.FWD

STOP

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

TIME SEARCH

STOP button (remote control)– Press to stop the

tape motion.

EJECT button (remote control)– Press to remove

tape from TV/VCR.

COUNTER

RESET

L button–

Press to select setting modes from the on screen

menu.

•

Press to enter digits when setting program.

(for example: setting clock or timer program)

•

- 7 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

- REAR VIEW - [Fig.3]

ANT.

+100 button– When selecting cable channels

which are higher than 99, press this button first,

then press the last two digits. (To select channel

125, first press the “+100” button then press “2”

and “5”).

8 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

s button–

Press to select a mode from a particular menu.

•

16 MENU button– Press to display the main menu on

the TV screen.

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 25.)

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 23.)

COUNTER RESET button– Press to reset counter

to 0:00:00.

20 GAME button– Set the game mode and external

input mode at the same time. (See page 14.)

21 TIME SEARCH button– Press to activate Time

Search mode.

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

23 MUTE button– Mutes the sound. Press it again to

resume sound.

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

25 WAKE UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See page 23.)

26 Power cord– Connect to a standard AC outlet

(120V/60Hz).

(for example: LANGUAGE or USER’S SET UP)

9 PLAY button– Press to begin playback.

K button–

Press to select setting modes from the on screen

menu.

•

Press to enter digits when setting program.

•

(for example: setting clock or timer program)

10 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

B button–

When setting program (for example: setting clock

•

or timer program), press to determine your selec-

tion and proceed to the next step you want to

input.

Press to determine setting modes from on screen

menu.

•

Press to select a mode from a particular menu.

•

(for example: LANGUAGE or USER’S SET UP)

11 REC button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

12 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer

Recording.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

14 Cassette compartment

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

27 ANT. terminal– Connect to an antenna or cable

system.

_{Download from Www.Somanuals.c}-_om8_.-_{All Manuals Search And Download.}

1K09

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

From Cable System or

Satellite Dish

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box

(Not supplied)

Rod Antenna

(Supplied with 13” model only)

OUT

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

ANT.

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied)

Flat twin-lead cable

VHF/UHF COMBINED ANTENNA

VHF/UHF SEPARATE ANTENNAS

The VHF/UHF Rod Antenna (supplied with 13”

In some areas it will be necessary to use an outdoor

model only) is detachable. Insert the stem of the anten- antenna.

na into the hole on the upper-back portion of the

CABLE WITHOUT CONVERTER/

TV/VCR. Connect the VHF/UHF Rod Antenna or

VHF/UHF Combination Antenna to the ANT. terminal

of the TV/VCR as shown in the diagram above. For

the best reception, fully extend the VHF/UHF Rod

Antenna and make the necessary adjustments. (Avoid

touching the top section when adjusting.)

NOTE:

Before plugging the Rod antenna into antenna termi-

nal, check that the pin is not bent. If it is bent,

straighten the pin as illustrated, then plug the pin into

antenna terminal.

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

Bent pin

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown here.

Cable Plug

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

(Straight pin)

(Needs to be straightened)

NOTE:

The connection of an indoor antenna may not always

give acceptable TV reception.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

- 9 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

INSTALLING THE BATTERIES

1. Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

3)Replace the cover.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO IN/ VIDEO IN jacks of

your TV/VCR. Then press the CHANNEL K or

button until “AUX” appears on the screen.

NOTE: “AUX” is found below the

lowest memorized channel.

AUX

(Example: CH2)

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just

select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then

select the channel to be viewed on the Cable Box or Satellite Box.

The tuner scans and memorizes all active channels in

your area.

NOTES:

CHANNEL SET UP FOR THE

FIRST TIME

The TV/VCR distinguishes between standard TV

channels and cable channels.

•

1 Plug in the TV/VCR power cord

Plug the TV/VCR power cord into a

standard AC outlet.

If you want to play or record a video tape

BEFORE presetting the tuner, you must press the

MENU button on the remote control. To preset the

tuner again, see “CHANNEL SET UP AGAIN” on

page 12.

The TV/VCR may memorize TV channels as

CATV channels if reception conditions are poor. If

this happens, try the AUTO MEMO action again

when reception conditions are better.

•

NOTE:

If some digits appear in the corner of

the screen, press the POWER button

without unplugging the power cord.

•

2 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR

5 After scanning

3 Select “ENGLISH” or “ESPAÑOL”

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with the remote

control number buttons or CHANNEL K or L.

– SET UP –

Select “ENGLISH” or

LANGUAGE

“ESPAÑOL”=Spanish using the

F.FWD/B or REW/s button. “[ ]”

indicate the selected language.

[ENGLISH] ESPAÑOL

AUTO PRESET

4 Begin auto preset

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then press the F.FWD/B button.

– SET UP –

LANGUAGE

[ENGLISH] ESPAÑOL

AUTO PRESET

- 10 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

TO SELECT A DESIRED CHANNEL

4 Select the day

You can select the desired channel by using the

CHANNEL K or L button on or directly pressing

the number buttons on the remote control.

Note for using the number buttons:

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 6th → 06)

0 5

0 6 – – – – – – –

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

When selecting cable channels which are higher

•

than 99, press the +100 button first, then, press the

last two digits. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

– MANUAL CLOCK SET –

MONTH DAY YEAR

5 Select the year

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2003)

You must proceed single-digit channel numbers

with a zero (Example: 02 ... 09).

•

0 5

0 6 TUE 2 0 0 3

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

CLOCK SET UP

(AUTO / MANUAL)

6 Select the hour

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

– MANUAL CLOCK SET –

MONTH DAY YEAR

The TV/VCR clock must be set correctly before

VCR timer recording is possible. It is suggested that

the clock be set manually when first setting up the

TV/VCR. Then, set to [on] the auto clock setting

which will periodically correct the setting if neces-

sary.

NOTE: If you cannot receive a station with time

signals, auto clock setting cannot be performed. Use

manual setting only.

0 5

0 6 TUE 2 0 0 3

HOUR

0 5

MINUTE

– – PM

Then, press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: 40)

0 5

0 6 TUE 2 0 0 3

HOUR

0 5

MINUTE

4 0 PM

MANUAL CLOCK SETTING

Make sure ...

8 Start the clock

5:40 PM

The TV/VCR is turned on.

In the example below, the clock is to be set to:

•

Press the MENU button on the

remote control.

DATE

May 6th, 2003

Although seconds are not dis-

played, they begin counting from

SETTING TIME 5:40PM

00 when you press the MENU button on the remote

control. Use this feature to synchronize the clock

with the correct time.

– M E N U –

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L

button to point to “SETTING

CLOCK”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

NOTE:

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps [1] and [2].

2)Select where you want to change using the

F.FWD/B or REW/s button.

3)Enter correct numbers using the PLAY/K or

STOP/L button.

– SETTING CLOCK –

2 Select “MANUAL CLOCK

SET”

Press the PLAY/K or STOP/L

button to point to “MANUAL

CLOCK SET”.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

Then, press the F.FWD/B button.

4)Press the MENU button on the remote control to

start the clock.

– MANUAL CLOCK SET –

MONTH DAY YEAR

3 Select the month

PLEASE NOTE:

Press the PLAY/K or STOP/L

button until your desired month

appears. (Example: May → 05)

Then, press the F.FWD/B button.

0 5

– – – – – – – – –

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the F.FWD/B or REW/s button to turn [OFF]

this function. Then you can manually adjust the

clock.

HOUR

– –

MINUTE

– – – –

- 11 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTOMATIC CLOCK SETTING

Make sure ...

NOTE: During Auto Clock CH Search, the picture

may be distorted. This is normal.

The TV/VCR is turned on.

Confirm the TV/VCR is receiving a RF (Radio

Frequency) signal from either an antenna or cable

system connection using the ANT IN jack on the

rear of the TV/VCR.

•

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L

button to select “SETTING

CLOCK”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

NOTE:

If a cable converter box is being used, make sure it

is powered on.

•

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

You must use the TV/VCR remote control to per-

form the clock setting procedure.

If the TV/VCR is connected directly to a cable

converter box or satellite box, the local PBS station

must be selected on the cable box itself, and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically

•

Press the F.FWD/B button to

select setting clock.

Press the STOP/L button to select

“AUTO CLOCK CH”.

Press the F.FWD/B or REW/s

buttons until you locate Auto

Clock Set station number. See item

3 above.

– SETTING CLOCK –

AUTO CLOCK

[ON]

•

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[

45]

[OFF]

Press the MENU button to exit the screen.

1 Select “SETTING CLOCK”

5 Turn off the TV/VCR

Press the MENU button on the

Once the TV/VCR is turned off , it will periodically

check and set the correct date and time.

– M E N U –

remote control.

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

CHANNEL SET UP AGAIN

TIME SEARCH

Make sure ...

Press the POWER button to turn on the TV/VCR.

– SETTING CLOCK –

•

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B button until

AUTO CLOCK [ON] appears.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

1 Select “CHANNEL SET UP”

[OFF]

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

3 Begin “AUTO CLOCK CH SEARCH”

Press the STOP/L button to select “AUTO CLOCK

TIME SEARCH

Then, press the F.FWD/B button.

CH SEARCH”.

Press the F.FWD/B button.

– SETTING CLOCK –

The TV/VCR is now searching

•

AUTO CLOCK

[ON]

2 Begin auto preset

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

– CHANNEL SET UP –

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

seconds per channel.

“_ _” appears at the lower left of

the screen when the search has

ended.

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then, press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

[OFF]

ADD / DELETE CH (TV)

AUTO PRESET

•

– AUTO CLOCK CH SEARCH –

3 After scanning

Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See item

4 below.

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 11.

•

The tuner stops on the lowest memorized channel.

_ _

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

•

Press the MENU button to exit the screen.

- 12 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

2 Select “ENGLISH” or “ESPAÑOL”

Select “ENGLISH” or “ESPAÑOL”= Spanish using

the F.FWD/B or REW/s button.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

3 Exit the Language mode

Press the MENU button on the remote control to

return to TV mode.

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

NOTE: If for some reason the menu is in Spanish,

press the MENU button on the remote control, press

the PLAY/K button to point to “IDIOMA

[ESPAÑOL]”, then press the F.FWD/B button, then

press the MENU button on the remote control.

– CHANNEL SET UP –

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

ADD / DELETE CH (TV)

AUTO PRESET

Press the F.FWD/B button.

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

First Sunday of April : At 2 AM the clock imme-

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

3 Enter the desired channel number

Press the PLAY/K or STOP/L but-

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it) (Example:

CH8)

ADD / DELETE

•

4 Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

•

Make sure ...

Press the POWER button to turn on the TV/VCR.

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

again, the channel is memorized again.

•

1 Select “SETTING CLOCK”

Added channel: Light blue.

Deleted channel: Light red.

Press the MENU button on the

– M E N U –

remote control.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

5 Exit the channel setup mode

Press the MENU button on the remote control to

returns to TV mode.

TIME SEARCH

Then, press the F.FWD/B button.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the PLAY/K or STOP/L but-

– SETTING CLOCK –

ton to point to “D.S.T.”.

Then, press the F.FWD/B or

REW/s button until [ON] appears.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

SELECTING THE LANGUAGE

Make sure ...

[ON]

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

the screen menu and not the audio source.

•

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

1 Select “LANGUAGE”

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

Press the MENU button on the

remote control.

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to “LANGUAGE”.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

F.FWD/B or REW/s button.

- 13 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

3 Adjust sound

Press the VOLUME X or Y button

to adjust the volume.

Press the MENU button on the

– M E N U –

remote control.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to ”PICTURE CON-

TROL”.

VOLUME 20

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

GAME MODE

2 Select item you want to adjust

Press the PLAY/K or STOP/L button until desired

This function enables you to decrease the TV screen

contrast and making it suitable for use with a TV

GAME.

control is displayed.

BRIGHT

CONTRAST

NOTE: This function can not be set during recording.

BRIGHT

COLOR

–

P +

TINT

Press the GAME button on the

GAME

remote control. “GAME” appears

on the screen.

SHARPNESS

3 Adjust the picture control

When you press the GAME button;

Press the F.FWD/B or REW/s button to adjust to

The TV/VCR comes on automatically if it is off.

The TV/VCR will be in external input mode auto-

•

your desired level.

matically.

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

BRIGHT

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

ton on the remote control.

CONTRAST

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

DEGAUSSING

Magnetism from nearby appliances might affect the

color of the TV picture.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect

power cord from AC outlet then reconnect it after 30

minutes.

to purple

to green

to clear

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 14 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

F.FWD/B or REW/s button. Press the MENU but-

ton on the remote control to return to TV mode.

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news, pre-recorded tapes with either a dia-

logue caption or text display.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

NOTE:

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

WHEN THE CLOSED CAPTION MODE IS ON

The On-Screen Display will disappear after 5 seconds.

This is also true when the MUTE button is pressed,

and when the PAUSE/STILL button is pressed

while recording.

•

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

V-CHIP SET UP

Make sure ...

TV/VCR is turned on.

You have the TV/VCR remote control.

•

1 Select “V-CHIP SET UP”

– M E N U –

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to select “V-CHIP SET UP”.

Then, press the F.FWD/B button.

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture ghosts

•

INDEX SEARCH

•

2 Enter Access code

Use the numbers on the remote

control to enter the access code.

ACCESS CODE

or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

If the TV/VCR displays a black

box on the TV screen, this means

that the TV/VCR is set to the

TEXT mode. To clear screen,

select [CAPTION1], [CAPTION2]

or [OFF].

•

For the first time set-up or in the

event the TV/VCR has lost power,

•

enter the default code of the numbers: 0000.

– V-CHIP SET UP –

3 Select “TV RATING”

Press the PLAY/K or STOP/L but-

ton to select “TV RATING”.

Then, press the F.FWD/B button.

TV RATING

MPAA RATING

CHANGE CODE

Make sure ...

TV/VCR is turned on.

•

– M E N U –

1 Select “CAPTION”

TIMER PROGRAMMING

4 Blocking TV programs

Press the PLAY/K or STOP/L but-

ton to select “TV rating” that you

wish to block.

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

CHANNEL SET UP

TV–Y

[VIEW]

TV–Y7

TV–G

(

)

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CAPTION”.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

TV–PG (

)

TV–14

(

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

TV–MA(

When you select the rating catego-

•

ry and turn it [BLOCK], the higher rating will turn

[BLOCK] automatically. Also, the lower rating will

turn [VIEW] automatically.

2 Select your desired caption

Press the F.FWD/B or REW/s but-

ton until your desired caption menu

appears. ([CAPTION1], [CAP-

TION2], [TEXT1] or [TEXT2])

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

When you turn “TV-Y” to [VIEW], then all ratings

•

will turn to [VIEW] automatically.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TV-Y7

TV-G

TV-PG

TV-14

Appropriate for children seven and older

General Audience

Parental Guidance suggested.

Unsuitable for children under 14

3 Exit the caption setting mode

Press the MENU button on the remote control to

return to TV mode.

TO CANCEL THE CLOSED CAPTION SYSTEM

Repeat steps [1] and [2], select [OFF] using the

TV-MA Mature audience only

- 15 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

a station that is not protected. If the (PROTECTED)

appears on the screen, please change the channel to a

station that is not protected.

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to

enter the setting and exit the screen.

1)Follow steps [1] and [2].

2)Press the F.FWD/B button to select "TV RAT-

ING". Select a TV rating to be unblocked by press-

ing the PLAY/K or STOP/L button.

Then press the F.FWD/B button to unblock the

rating.

V-CHIP SET UP SUB RATINGS

When you select the ratings of TV-Y7,TV-PG,TV-14

or TV-MA you will have the option of selecting sub

rating categories.

3)Press the MENU button on the remote control to

exit the screen.

1 Select “V-CHIP SET UP”

– M E N U –

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

remote control.

USER’S SET UP

MPAA RATING SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to select “V-CHIP SET UP”.

Then, press the F.FWD/B button.

– M E N U –

1 Select “V-CHIP SET UP”

TIMER PROGRAMMING

INDEX SEARCH

PICTURE CONTROL

SETTING CLOCK

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to select “V-CHIP SET UP”.

Then, press the F.FWD/B button.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

2 Enter Access code

Use the numbers on the remote con-

trol to enter the access code.

(Default code is 0000.)

ACCESS CODE

INDEX SEARCH

2 Enter Access code

Use the numbers on the remote con-

trol to enter the access code.

ACCESS CODE

– V-CHIP SET UP –

3 Select “TV RATING”

Press the PLAY/K or STOP/L but-

ton to select “TV RATING”.

Then, press the F.FWD/B button.

TV RATING

MPAA RATING

CHANGE CODE

– V-CHIP SET UP –

3 Select “MPAA RATING”

Press the PLAY/K or STOP/L but-

ton to point to “MPAA RATING”.

Then, press the F.FWD/B button.

TV RATING

MPAA RATING

CHANGE CODE

4 Selecting Sub-Ratings”

Press the STOP/L button to select

the sub-rating you wish to block.

Then, press the F.FWD/B button.

TV–Y7

[BLOCK]

When you select [TV-Y7]:

Press the STOP/L or PLAY/K button to select

“FV” (Fantasy Violence).

Then, press the F.FWD/B button to select

[BLOCK] or [VIEW].

When you select [TV-PG], [TV-14] or [TV-MA]:

Press the STOP/L or PLAY/K

•

4 Select your desired item

Press the PLAY/K or STOP/L but-

ton to point to your desired item.

Then, press the F.FWD/B button to

select [BLOCK] or [VIEW].

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

•

Selection

Rating Category Explanations

General Audience

button to select “D”(Suggestive

TV–PG

[BLOCK]

Dialog), “L”(Coarse Language),

“S”(Sexual Situation), or

“V”(Violence). Then, press the

F.FWD/B button to select

[BLOCK] or [VIEW].

Note: When you select [TV-MA],

“D” does not appear on the TV

screen.

PG-13

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

NC-17

(

)

[VIEW]

[BLOCK]

Mature audience only

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “G” to [VIEW], then all ratings

will turn to [VIEW] automatically.

•

The sub-ratings which set to [BLOCK] appears

next to the rating category in the TV rating menu.

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to

enter the setting and exit the screen.

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to

enter the setting and exit the screen.

CHANGING V-CHIP BLOCKED PRO-

GRAMMING

Note: To change the rating, the TV must be turned to

- 16 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGE ACCESS CODE

4 Enter New code

Use the number buttons to enter

your desired access code in the

NEW CODE space. Then enter the

same code in the CONFIRM

CODE space. V-CHIP SET UP

screen appear on the screen.

To change access code, follow the steps.

NEW CODE

X X X X

CONFIRM CODE

1 Select “V-CHIP SET UP”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to select “V-

CHIP SET UP”.

If you enter wrong code, repeat step 4, making sure

you enter the same new code exactly in the confirm

code space.

•

Then, press the F.FWD/B button.

ACCESS CODE

2 Enter Access code

Use the number on the remote con-

trol to enter the access code.

The default code is 0000.

5 Exit the V-Chip setting mode

Press the MENU button on the remote control to exit

the screen.

Note: If you unplug the power code or power failure

occurs, the changed access code will be lost and will

return to default (0000). Change your access code

again as necessary.

– V-CHIP SET UP –

3 Select “CHANGE CODE”

Press the PLAY/K or STOP/L but-

ton to select "CHANGE CODE".

Then, press the F.FWD/B button.

TV RATING

MPAA RATING

CHANGE CODE

PLAYBACK

This TV/VCR will operate with any cassette that has the

mark. For best results, we

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

•

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR. The

TV/VCR will automatically turn on.

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

Window

Avoid extreme heat, high humidity and magnetic

fields.

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

•

NORMAL PLAYBACK

AUTO REPEAT PLAYBACK

Make sure ...

The TV/VCR has the auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

TV/VCR power must be turned on.

•

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

2 To begin playback

PLAY

Press the PLAY button.

Note: If any menu is activated on

the screen, the PLAY button does

not function. Press the MENU but-

ton to clear the menu. then, press

the PLAY button.

1 Select “USER’S SET UP”

– M E N U –

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

remote control.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

STOP

3 To stop playback

Press the STOP button when play-

back is completed.

Download from Www.Somanuals.com. All Manuals Search And Download.

- 17 -

1K09

USER’S SET UP

–

2 Select “ALL” or “BLANK”

Press the PLAY/K or STOP/L but-

ton to point to “REPEAT PLAY”.

Press the F.FWD/B or REW/s

button repeatedly until your

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

desired selection [ALL] or [BLANK] appears.

3 Exit the Repeat Play setting

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback

is completed.

Press the MENU button on the remote control to

return to the TV mode.

4 Start playback

Press the PLAY button to start the Repeat Play.

”REPEAT PLAY B” appears.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

4 To activate “ZERO RETURN” mode

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to point to

“ZERO RETURN”.

•

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

Then, press the F.FWD/B button.

The counter will appear on the TV

screen.

LANGUAGE [ENGLISH]

The tape will automatically stop

CAPTION [OFF]

when the counter returns to

0:00:00.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

TO CANCEL THE REPEAT PLAY MODE

V-CHIP SET UP

ZERO RETURN

TIME SEARCH

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

TIME SEARCH

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

PICTURE SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback. (in the

SP / LP / SLP modes)

NOTES:

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

•

This function will not operate in recording mode.

•

In the example below: To watch a program after 2

hour 50 minutes from the present position, in either

direction.

2)Press it again and the TV/VCR will now search in

super high speed. (in the LP / SLP modes only)

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

1 Insert a tape.

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button (with each push it

will increase by 10 minutes).

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

3 Enter your desired time

Press the PLAY/K or STOP/L but-

TIME SEARCH

2 : 50

ton until your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

If you wish to cancel the Time

Search at this point, press the

MENU button on the remote control.

NOTE:

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

- 18 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE CONTROLS

TRACKING ADJUSTMENT

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

4 Begin Time Search

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

•

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

TO CANCEL THE TIME SEARCH at

this point

Press the STOP/EJECT button on the TV/VCR or

the remote control. This will delete the selected

time.

However when playing pre-recorded tapes or tapes

•

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

RENTAL PLAYBACK

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

STILL PICTURE

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines.Press

the PLAY button to return to playback.

NOTES:

Usually there will be video “noise” lines (black

and white streaks or dots) on the screen. This is

normal.

1 Select “USER’S SET UP”

Press the MENU button on the

remote control.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

•

TIME SEARCH

If the tape was originally recorded in SP or LP

mode, the still picture will be black and white in

addition to the “noise” lines.

This is not a fault of the machine, but is a limi-

tation of a TV/VCR with 2 video heads.

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

If it is left in the Pause mode for more than five

•

minutes, the TV/VCR will automatically switch to

the Stop mode.

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

NOISE CANCEL (in the Still mode)

4 Start playback

This feature allows you to reposition or reduce the

noise lines of a still picture. Press the PAUSE/STILL

button so that the noise lines change position on the

screen so you can see the picture in its entirety with-

out distracting noise lines.

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR.

•

NOTE: This feature can be activated ONLY when

viewing a tape recorded in the SLP mode. If the tape

was originally recorded in the SP or LP mode, the

still picture may revert to black and white in addition

to the “noise bars”. This is normal.

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

VERTICAL HOLD CONTROL

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

NOTE:

If there are video noise lines on the screen, reposition

or reduce them. Refer to “NOISE CANCEL”.

- 19 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

TWO DIFFERENT TAPE SPEEDS

ERASE PREVENTION

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

Tape Speed

Type of tape

SP mode

Recording/Playback Time

If you decide to record on

the tape again, cover the

hole with plastic tape.

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

Note: You can play back a tape recorded in LP mode

(Long Play).

Make sure ...

Transparent Tape

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTE: This unit will ONLY record and view the same channel.

SKIPPING UNWANTED

NORMAL RECORDING

You can ONLY watch the same TV program that is

being recorded.

SCENES DURING RECORDING

Press the PAUSE/STILL button to

PAUSE

temporarily stop recording.

Press the PAUSE/STILL or

RECORD button to resume record-

ing.

NOTES:

1 Select the channel to be recorded

Press the number buttons on the

CH 10

remote control or the CHANNEL

K or L button.

Remember: If the TV/VCR is con-

nected to a cable box or satellite

box, the TV/VCR must be on CH3 or CH4, then the

channel to be recorded must be selected on the cable

box or satellite box.

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape damage.

•

If “CLOSED CAPTION (ON)” is selected, the On-

Screen Display will appear for 5 seconds, then dis-

appear.

•

OTR (One Touch Recording)

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/VCR.

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

Make sure ...

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

•

3 Begin recording

Press the RECORD button.

REC

tape to the point at which you want to begin

recording.)

NOTES:

This function CANNOT be done from the remote

control.

•

4 Stop recording

Press the STOP button when recording is completed.

Recording starts immediately when the REC/OTR

button is pressed.

•

When the REC/OTR button is pressed 18 times, the

TV/VCR returns to the Normal Recording mode.

•

- 20 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

DATE:

July 4th, 2003

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

To show the remaining time, press the DISPLAY

button on the remote control so that “OTR”

appears on the TV screen. (It will show up

momentarily then disappear.)

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum

recording time, assuming the tape is started at the

beginning, is 8 hours using T-160 (or 6 hours using

T-120).

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, ejects the tape and turns itself off.

If you press the power button during OTR, the

TV/VCR continues recording until the selected

length is reached.

•

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL:

TAPE SPEED:

Make sure ...

If a cable box or satellite box is connected with

the TV/VCR you will be limited to record only

one channel. And the channel selector on the

TV/VCR must be selected to the output channel of

the boxes CH 3 or CH 4 and then the actual chan-

nel to be recorded must be selected on the boxes.

Clock must be set to the correct time and date

before setting the timer.

TV/VCR power must be turn on to program it.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

CH61

•

The channel you want to record is properly set in

advance.

•

1 Select the channel to be recorded

Press the number buttons on the remote control or

the CHANNEL K or L button.

Avoid over lap of programs ...

There is a chance that a program will not be record-

ed when programs overlap;

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

•

programs will begin recording in sequence.

The illustration below demonstrates the sequence

of recordings.

•

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

Recording Sequence

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

3 Begin OTR

OTR(2 : 30)

Press the REC/OTR button on the

TV/VCR as many times as needed.

The recording length will be deter-

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

mined by the number of times you

press the REC/OTR button. Each

additional push will increase the recording time by

30 minutes. It is set up to 8 hours.

1 Select “TIMER PROGRAMMING”

Press the MENU button on the

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Push(es) Display

1 push

Recording length

(normal recording)

remote control.

Confirm “TIMER PROGRAM-

MING” is pointed by pressing the

PLAY/K button.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

ZERO RETURN

TIME SEARCH

And press the F.FWD/B button.

If you have not yet set the clock, “MANUAL

CLOCK SET” appears. If so, follow stops [3] to

[8] on page 11. Then set the timer recording.

•

17 pushes

8:00

480 minutes

TIMER RECORDING

2 Select your desired program position (1~8)

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L but-

ton to select the desired program

position.

CH DATE

BEGIN END

- - -/- - - - - -:- -

-:- - - -

Then, press the F.FWD/B button.

In the following example, the timer is being set to record:

- 21 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Set the channel number

Press the PLAY/K or STOP/L but-

ton until the desired channel num-

ber appears.

(Example: CH61)

Then, press the F.FWD/B button.

8 Set end minute

– TIMER PROGRAMMING –

CH DATE BEGIN END

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: “50” for

8:50PM)

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

61 7/04 FRI 7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

– TIMER PROGRAMMING –

CH DATE BEGIN END

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

61 7/04 FRI 7:30^P

- - -/- - - - - -:- -

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

Press the PLAY/K (up) button

10 Finish setting the program

CH DATE

BEGIN END

until the desired date appears.

(Example: “7/04” for July 4th).

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 7/04 FRI -:- -

- - -/- - - - - -:- -

-:- - - -

Press the F.FWD/B or REW/s button. The program

is now completed.

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control to

return to original mode.

•

For every day recording : To record a TV program at

the same time on the same channel every day.

(Example: Monday through Sunday) :

11 Set the timer

Press the POWER button to set automatic timer

recording. The RECORD indicator lights up.

– TIMER PROGRAMMING –

Press the STOP/L (down) button

CH DATE

BEGIN END

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

until “EVRY DAY” appears.

Then, press the F.FWD/B but-

ton.

You must turn off the TV/VCR to activate automat-

ic timer recording.

•

For weekly recording : To record a

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

TV program at the same time on the same channel

every week. (Example: every Monday) :

– TIMER PROGRAMMING –

Press the STOP/L (down) button

CH DATE

BEGIN END

until “EVRY” and your desired

day of the week appear together.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

TIMER PROGRAM EXTENSION

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

5 Set beginning hour

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “ 7, PM” for 7:30PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

2)Repeat step [1] on page 21.

61 7/04 FRI 7:12^P

- - -/- - - - - -:- -

3)Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automat-

ically be set to the SLP mode.

6 Set beginning minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: “30” for

7:30PM)

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

61 7/04 FRI 7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

7 Set end hour

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the F.FWD/B button.

5)Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

- - -/- - - - - -:- -

-:- - - -

8:30^PM - -

-:- - - -

61 7/04 FRI 7:30^P

- - -/- - - - - -:- -

- 22 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CORRECT A PROGRAM

AUTO RETURN

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

bers using the PLAY/K or STOP/L button.

After setting a program;

1)Press the POWER button.

•

1 Select “USER’S SET UP”

– M E N U –

2)Repeat steps [1] - [2] on page 21.

3)Press the F.FWD/B button (or press the

REW/s button to go back one step) until the

part you want to correct begins flashing, then

make the changes pressing the PLAY/K or

STOP/L button.

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

remote control.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

4)Press the POWER button to set automatic timer

recording.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

After setting a program;

1)Press the POWER button.

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

•

2)Repeat steps [1] ~ [2] on page 21 and select a

program you want to cancel.

3)Press the T-PROG. CLEAR button.

4)Press the MENU button on the remote control to

return to TV mode.

While recording is in progress;

1)Press POWER button.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/VCR will rewind to the beginning of the recorded

program(s).

NOTE:

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

•

2)Press the STOP/EJECT button on the TV/VCR.

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

2)Press the MENU button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

5)Press the MENU button on the remote control to

return to TV mode.

4 Watch the recorded program

Press the PLAY button.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

WAKE UP TIMER

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

HINTS FOR AUTOMATIC

TIMER RECORDING

Make sure the channel you want to record is prop-

erly set in advance.

It is not necessary to press the RECORD button for

timer recording.

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

•

NOTES:

•

Use the remote control for this procedure.

Clock must be set to the correct time before setting

•

the timer.

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

not operate the unit manually.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

•

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, and the tape will be ejected.

1 Select “WAKE UP TIMER”

Press the WAKE UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s

button until [ON] appears.

•

WAKE UP B ON/OFF

[ON]

•

TIMER

TV/TAPE

TIME

[TV]

[12:00AM]

- 23 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

SLEEP TIMER

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

2 Select “TV” or “TAPE”

Press the PLAY/K or STOP/L but-

ton until to point to “TV/TAPE”.

Press the F.FWD/B or REW/s

button, and select [TV] or [TAPE].

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

[TV]

[12:00AM]

NOTE:

This function does not operate during Recording

•

mode.

3 Set wake up time

1 Select “SLEEP TIMER”

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

Press the PLAY/K or STOP/L but-

ton until to point to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

WAKE UP

TIMER

ON/OFF

TV/TAPE

B TIME

[ON]

[TV]

[12:00AM]

2 Set sleep time

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

Each additional push will increase (or decrease) the

time by 10 minutes.

your desired sleep time appears.

SLEEP TIMER [2:00]

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

Each additional push will increase

the time by 30 minutes up to 120 minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE WAKE UP TIMER

Repeat step [1] but select [OFF].

TO CANCEL THE SLEEP TIMER

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer press the WAKE

UP/SLEEP button twice, then press the MENU but-

ton on the remote control to exit the sleep timer set-

ting.

COPYING A VIDEO TAPE

You can make copies of video tapes made by friends

or relatives for your enjoyment.

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record onto into the TV/VCR’s cassette compart-

ment. This will become the copy.

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

[Fig.8]

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

[The TV/VCR]

VIDEO

AUDIO

4)Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

NOTE: “AUX” is found below the lowest memo-

rized channel. (Example: CH2)

5)Press the RECORD button on the TV/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

[Ex: Source (playing)

VCR or camcorder]

NOTE: For best results during dubbing, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

AUDIO

Audio/Video

adapter cable

(not supplied)

OUT

VIDEO

- 24 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

WHEN THE CLOSED CAPTION MODE IS OFF:

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

5:40PM

CH2

Press

once

Press

once

COUNT 0:12:34

Press once

ON:

OFF mode

Clock/Counter mode

WHEN THE CLOSED CAPTION MODE IS

The On Screen Display disappear after 5 seconds.

•

STOP

5:40 PM

CH2

This is true even if the MUTE button is pressed, or the

PAUSE/STILL button is pressed while recording.

•

COUNT 0:12:34

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time

will not change on a blank tape or blank portions on

the tape.)The “–” indication will appear when the

tape has rewound further than “0:00:00” on the tape

counter.

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

MAINTENANCE

back, the video heads in your TV/VCR may need

to be cleaned.

CABINET CLEANING

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

1.Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-488-1222, to

locate an Authorized Service Center.

NOTES:

Remember to read the instructions included with

the video head cleaner before use.

Clean video heads only when problems occur.

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

•

AUTO HEAD CLEANING

•

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

SERVICING

Should your TV/VCR become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

488-1222, to locate an Authorized Service Center.

Playback picture may become blurred of interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

- 25 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Program TV channels into TV/VCR.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

Adjust tracking control for a better picture using the CHANNEL

or L button on the TV/VCR.

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 25.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

Magnetism from nearby appliances or unshielded stereo speaker or

geomagnetism might affect the color of the TV picture. Move the

TV/VCR away from the appliances, the TV/VCR can repair itself

automatically. If you want to repair immediately, unplug the

TV/VCR power cord, then plug it in again 30 minutes or so later.

No power.

•

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

•

Timer recording is not possible.

Cannot go into Record mode.

•

Playback picture is partially noisy.

•

No picture but the audio is OK in

playback.

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

•

Different color marks on screen.

•

CLOSED CAPTION PROBLEM

My TV/VCR is showing captions

that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

- 26 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

13 or 19 inch in-line gun, 90˚

deflection tube

NTSC-M

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Closed caption system :§15.119/FCC

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary two-head

1/2 inch

OTHER SPECIFICATIONS

[ 13 inch model ]

Power requirement : AC 120V/60Hz

Power consumption : 65W

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

Dimensions :

H:15-3/8” (389mm)

W:14-1/2” (367mm)

D:14-7/8” (377mm)

23.1 lbs (10.5kg)

#2~#6

#7~#13

#14~#69

Weight :

[ 19 inch model ]

Power requirement : AC 120V/60Hz

Power consumption : 80W

VHF :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Dimensions :

H:19-1/2” (493mm)

W:19-3/8” (491mm)

D:18-3/4” (475mm)

43.0 lbs (19.5kg)

Weight :

Antenna input :

VHF/UHF 75 ohms

unbalanced

Video input :

Audio input :

Earphone :

RCA connector [ 1

1/8” monaural (3.5 mm)

Designs and specifications are subject to change

without notice and without our legal obligation.

If there is a discrepancy between languages, the

default language will be English.

•

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 27 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-

tamente la misma. En este manual se muestra el modelo de 13".

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

EARPHONE

1 2 3 4 5 6 7 8 910 11 12 1314

)–

4 Botones de volumen (VOLUME

Ajustan el nivel del volumen.

5 Botones de canales (CHANNEL K/ L)–

Púlselos para seleccionar los canales deseados

para ver o grabar.

WAKE-UP

/SLEEP

POWER

EJECT

CHANNEL

RETURN

Se puede mostrar el menú principal en la pantalla

del televisor pulsando repetidamente este botón del

televisor/videograbadora.

Función de seguimiento– Pulse los botones

para minimizar el ruido de vídeo (líneas o puntos

en la pantalla) durante la reproducción.

6 Ventanilla sensora del mando a distancia–

Recibe las señales infrarrojas procedentes del

mando a distancia.

CHANNEL

VOLUME

+100

DISPLAY

MUTE

7 Botón L–

Púlselo para seleccionar los modos de ajuste

desde el menúde la pantalla.

•

PLAY

REW

F.FWD

Púlselo para introducir dígitos cuando establezca

un programa.

•

STOP

SPEED PAUSE/STILL

RECORD

(Por ejemplo: Para ajustar el reloj o establecer un

programa de temporizador)

[ Televisor/videograbadora ]

Botón de parada/expulsión (STOP/EJECT)–

Púlselo para detener la cinta. Púlselo en el modo

de parada para expulsar la cinta del

televisor/videograbadora.

T-PROG.

CLEAR

GAME

TIME SEARCH

COUNTER

RESET

[ Control remoto ]

Botón de parada (STOP)– Púlselo para deten-

1 Toma de entrada de vídeo (VIDEO)–

er la cinta.

Conéctela a la toma de salida de vídeo de su

videocámara u otra videograbadora.

Botón de expulsión (EJECT)–Púlselo para

expulsar la cinta del televisor/videograbadora.

2 Toma de entrada de audio (AUDIO)–

Conéctela a la toma de salida de audio de su equipo

de audio, videocámara u otra videograbadora.

3 Botón de la alimentación (POWER)–

Púlselo para encender y apagar el

8 Botón de rebobinado (REW)– Púlselo para

rebobinar la cinta, o para ver la imagen en retro-

ceso rápido durante el modo de reproducción.

(Búsqueda con rebobinado)

Botón s–

televisor/videograbadora. Púlselo para activar la

grabación con temporizador.

Púlselo para seleccionar un modo desde un menú

•

particular.

- 28 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

ANT.

(Por ejemplo: IDIOMA o ADJUST DE USER)

9 Botón de reproducción (PLAY)– Púlselo

para iniciar la reproducción.

99, pulse primero este botón, y luego pulse los

dos últimos dígitos. (Para seleccionar el canal

125, pulse primero el botón “+100” y luego el

“2” y el “5”.)

Botón K–

16 Botón de menú (MENU)– Púlselo para visu-

alizar el menú principal en la pantalla del televi-

sor.

17 Botón del visualizador (DISPLAY)–

Visualiza el contador o el número del canal actu-

al y la hora actual en la pantalla del televisor.

18 Botón de velocidad de cinta (SPEED)–

Púlselo para elegir la velocidad de grabación

deseada: SP/SLP.

Púlselo para seleccionar los modos de ajuste

•

desde el menú de la pantalla.

Púlselo para introducir dígitos cuando establezca

un programa.

(Por ejemplo: Para ajustar el reloj o establecer un

programa de temporizador)

10 Botón de avance rápido (F.FWD)– Púlselo

para avanzar rápidamente la cinta, o para ver la

imagen en avance rápido durante el modo de

reproducción. (Búsqueda con avance rápido)

Botón B–

19 Botón T-PROG. CLEAR– Púlselo para cance-

lar un programa de temporizador.

Botón de reposición del contador

(COUNTER RESET)– Púlselo para reponer el

contador a 0:00:00.

Cuando establezca un programa (por ejemplo:

para ajustar el reloj o para establecer un progra-

ma de temporizador), púlselo para determinar su

elección y vaya al paso siguiente que quiera

introducir.

•

20 Botón de juego (GAME)– Establece el modo

del juego y el modo de entrada externa al mismo

tiempo.

21 Botón de búsqueda con tiempo (TIME

SEARCH)– Púlselo para activar el modo de

búsqueda con tiempo.

Púlselo para determinar los modos de ajuste

desde el menúde la pantalla.

Púlselo para seleccionar un modo desde un

menúparticular.

•

22 Botón de pausa/imagen fija

(Por ejemplo: IDIOMA o ADJUST DE USER)

(PAUSE/STILL)– Púlselo para detener tempo-

ralmente la cinta durante la grabación o para ver

una imagen fija durante la reproducción.

23 Botón de silenciamiento (MUTE)– Silencia

el sonido. Púlselo de nuevo para recuperar el

sonido.

11 Botón de grabación (REC)– Púlselo para ini-

ciar la grabación manual.

Botón de grabación de un toque (OTR)–

Activa la grabación de un toque. (Sólo en el tele-

visor/videograbadora)

12 Indicador de grabación (RECORD)–

24 Botón de retorno de canal (CHANNEL

RETURN)– Púlselo para volver al canal anterior.

Por ejemplo, pulsando una vez este botón, la

visualización del canal cambiará de 3 (canal actu-

al) a10 (canal anterior), y al pulsarlo por segunda

vez, el canal cambiará del 10 al 3.

25 Botón del temporizador despertador/para

dormir (WAKE UP/SLEEP)– Ajusta el tempo-

rizador para despertarse/dormir.

Parpadea durante la grabación.

Se enciende en el modo de espera de la grabación

con temporizador.

13 Toma de auriculares (EARPHONE)– Para

conectar los auriculares (no suministrados) y

escuchar en privado. La toma es mono y tiene un

tamaño de 1/8”(3.5 mm).

14 Compartimiento del videocasete

15 Botones numerados– Púlselos para selec-

cionar los canales deseados para ver o grabar.

Para seleccionar canales del 1 al 9, pulse primero

el botón 0 y luego el botón 1 a 9.

26 Cordón de alimentación– Conéctelo a la

toma de CA estándar (120V/60Hz).

27 Terminal de antena (ANT.)– Para conectar

una antena o sistema de televisión por cable.

Botón +100– Cuando seleccione canales de

televisión por cable cuyo número sea superior al

- 29 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIONES DE ANTENA/CABLE

Desde el cable coaxil o

caja de emisiones vía

satélite de 75 ohm del

sistema de Cable

Caja de CATV

o caja de emi-

siones vía satélite

(no incluído)

Antena combinada de

VHF/UHF

(no incluído)

Antena de varilla UHF/VHF

(incluído para solamente 13”)

OUT

Antena VHF

(no incluído)

Desde el

sistema de Cable

Antena UHF

(no incluído)

ANT.

Combinador de

VHF/UHF

(no incluído)

ANT.

Cable coaxil

de 75 ohm (no incluído)

Cable bifilar plano

de los canales deberá hacerse con el convertidor de tele-

visión por cable con el convertidor de emisiones vía

satélite. Esto significa que los canales no podrán ser

cambiados con el mando a distancia del

televisor/videograbadora. La grabación inatendida se

limita a un canal cada vez.

PARA GRABAR UN CANAL

CODIFICADO/DESCODIFICADO

1. Ajuste el selector de canales del

ANTENA COMBINADA DE VHF/UHF

La antena de varilla de VHF/UHF (incluído para sola-

mente 13”) es desmontable. Inserte el vástago de la

antena en el agujero de la parte trasera superior del tele-

visor/videograbadora.

Conecte la varilla de antena de VHF/UHF o la antena

combinada de VHF/UHF al terminal ANT. del televi-

sor/videograbadora.

televisor/videograbadora al canal de salida del con-

vertidor de televisión por cable o del convertidor de

emisiones vía satélite. (Ej.: CA3)

2. Seleccione el canal que desee grabar de su conver-

tidor de televisión por cable o del convertidor de emi-

siones vía satélite.

ANTENAS SEPARADAS DE VHF/UHF

En algunos lugares será necesario utilizar una antena

exterior.

CABLE SIN CONVERTIDOR/DESCODIFI-

CADOR

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su

MODO DE ENTRADA EXTERNA

televisor/videograbadora sin convertidor.Utilizando esta

conexión usted podrá:

1)Utilizar el mando a distancia del

televisor/videograbadora para seleccionar canales.

2)Programar uno o más canales sin codificar para

realizar la grabación automática con temporizador.

NOTA: Con esta unidad SÓLO se podrá grabar y ver

un mismo canal al mismo tiempo.

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los cables

de salida de audio/vídeo del equipo de reproducción a las

tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón CHAN-

NEL K o L hasta que “AUX” aparezca en la pantalla.

Usted puede programar el temporizador para que explore

todos los canales que puedan recibirse en su zona.

CABLE CON CONVERTIDOR/DESCODIFI-

CADOR O CONVERTIDOR DE EMISIONES VÍA

SATÉLITE

Si su servicio de televisión por cable le suministra un

convertidor, o si usted utiliza un sistema de emisiones

vía satélite, usted podrá utilizar las conexiones básicas

mostradas aquí.

INSTALACIÓN DE LAS PILAS

1)Abra la tapa del compartimiento de las pilas del mando

a distancia presionándola en el sentido de la flecha.

2)Inserte 2 pilas tamaño “AA” en el compartimiento de las

pilas, en el sentido indicado por las marcas de polaridad

(+/-).

Utilizando estas conexiones, usted también podrá

grabar canales codificados. Sin embargo, la selección

3)Vuelva a poner la tapa.

- 30 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARACIÓN DE CANALES POR

PRIMERA VEZ

1)Enchufe el cable de alimentación del

televisor/videograbadora en una toma de CA están-

dar.

NOTA: Si aparezcan algunos digitos en el rincón de

la pantalla, pulse el botón POWER sin desenchufar

el cable de alimentación.

2)Pulse el botón POWER para encender el televi-

sor/videograbadora.

3)Seleccione “ENGLISH” o “ESPAÑOL” utilizando

el botón F.FWD/B o REW/s. “[ ]” indica el

idioma seleccionado.

4)Pulse el botón PLAY/K o STOP/L para señalar

“AUTOPRESELECCION”.

AJUSTE DEL RELOJ

Cerciórese...

La alimentación del televisor/videograbadora

deberá estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 6 de mayo de 2003

HORA: 5:40 PM

1)Pulse el botón MENU en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”.

Luego, pulse el botón F.FWD/B.

2)Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”.

•

Luego, pulse el botón F.FWD/B.

3)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el mes deseado. (Ejemplo: Mayo - 05)

Luego, pulse el botón F.FWD/B.

Luego pulse el botón F.FWD/B. El sintonizador

explorará y memorizará todos los canales activos

de su área.

NOTAS:

4)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el día del mes deseado. (Ejemplo: 6 - 06)

Luego, pulse el botón F.FWD/B.

5)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el año deseado. (Ejemplo: 2003)

Luego, pulse el botón F.FWD/B.

6)Pulse el botón PLAY/K o STOP/L hasta que

aparezca la hora deseada. (Ejemplo: 5, PM)

Luego, pulse el botón F.FWD/B.

7)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el minuto deseado. (Ejemplo: 40)

8)Pulse el botón MENU en el mando a distancia.

Aunque los segundos no se visualizan, éstos

empiezan a contar desde 00 cuando se pulsa

MENU en el mando a distancia. Utilice esta fun-

ción para sincronizar el reloj con la hora correcta.

El televisor/videograbadora distingue entre los

canales de televisión estándar y los canales de tele-

visor por cable.

•

Si desea reproducir o grabar una cinta ANTES de

preajustar el sintonizador, usted tendrá que pulsar

el botón MENU en el mando a distancia. Para

preajustar de nuevo el sintonizador, consulte

“REPETICIÓN DE LA PREPARACIÓN DE

CANALES”.

•

La unidad de televisor/videograbadora puede

reconocer los canales de TV como ellos de TV por

cable a causa de los condiciones de recepción. En

este caso, pruebe el preajuste automático de nuevo

en los condiciones finas de recepción.

•

5)El sintonizador se para en el canal memorizado

más bajo. Si desea recuperar canales selecciona-

dos, usted podrá seleccionar directamente el canal

deseado con los botones numerados del mando a

distancia o con los botones CHANNEL K o L.

- 31 -

1K09

Download from Www.Somanuals.com. All Manuals Search And Download.

Get it fixed, at your home or ours!

Your Home

For repair in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME ^R(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com

www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Center.

1-800-488-1222

Call anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.)

1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

Au Canada pour service en français:

1-800-LE-FOYER

1-888-SU-HOGAR

(1-800-533-6937)

(1-888-784-6427)

www.sears.ca

Registered Trademark / ^TMTrademark / ^SMService Mark of Sears, Roebuck and Co.

Marca Registrada / ^TMMarca de Fábrica / ^SMMarca de Servicio de Sears, Roebuck and Co.

^MCMarque de commerce / ^MDMarque déposée de Sears, Roebuck and Co.

LIMITED 90 DAY WARRANTY FOR 13 INCH MODEL

If this (product) experiences any failure due to a defect in material or workmanship within 90 days from the date of

purchase, return it to your nearest Sears store, and it will be replaced free of charge.

This warranty applies only if this (product) is used for private household purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

FULL 90 DAY WARRANTY FOR 19 INCH MODEL

For 90 days from the date of purchase, Sears will repair any defect in material or workmanship in this TV/VCR

combination, free of charge. For one year from the date of purchase, Sears will supply, at no charge, replacement

for defective parts.

Two (2) years for Picture Tube. Certain parts are excluded from this warranty.

The above warranty coverage applies only to TV/VCR combination which are used for private household purposes.

TO OBTAIN WARRANTY SERVICE, SIMPLY RETURN THE TV/VCR COMBINATION TO THE NEAREST SEARS

SERVICE CENTER IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Roebuck and Co., Dept. 817WA Hoffman Estates, IL 60179

For the location of a Sears Service Center in your area : 1-800-488-1222

Printed in Malaysia

0EMN02083

T5407UH / T7408UJ * * * * *

Download from Www.Somanuals.com. All Manuals Search And Download.

Shinco Air Conditioner BM User Manual
Sigma Stereo Amplifier ADA 21S User Manual
Soleus Air Dehumidifier GM DEH 30M 1GM DEH 45 1 User Manual
Sony Car Stereo System XR CA320 User Manual
Sony Computer Monitor Color Graphic Display User Manual
Sony Home Theater System CMT SX2D User Manual
Sony Speaker SA VE345 User Manual
SoundMax Home Theater System SM CDM1042 User Manual
Swisher Log Splitter LS67528S User Manual
Tanaka Portable Generator DEG 600 User Manual