Owner’s Manual
6727FRE
SUPPLIED ACCESSORIES
This unit comes with the following accessories. Please confirm that all the accessories
are included.
P Owner's Manual
P Remote Control
P AA batteries x 2
(1EMN20176)
(NE237UD)
NOTE
If any of accessories are missing, please contact your dealer.
Thank you for purchasing this product.
Please make sure to read this manual before using the product and pay par-
ticular attention to the Safety Instructions enclosed within.
When you have finished reading this manual, store it in a safe place for easy
access in the future.
IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING
AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE
Before you use this unit, you need to complete connections.
Refer to “Connections” on pages 10-13.
To record a program easily, refer to “Easy DVD recording” on pages 46-47
after connections are completed.
(You CANNOT copy any copyright protected DVD disc with this unit.)
INSTRUCCIONES EN ESPAÑOL INCLUDAS.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
13.Outdoor Antenna grounding - If an outside antenna or
cable system is connected to the TV/VCR/DVD, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-dis-
charge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig. A)
19.Damage Requiring Service - Unplug this TV/VCR/DVD
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged or
frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/VCR/DVD.
c. If the TV/VCR/DVD has been exposed to rain or water.
d. If the TV/VCR/DVD does not operate normally by follow-
ing the operating instructions. Adjust only those controls
that are covered by the operating instructions, as
improper adjustment of other controls may result in
damage and will often require extensive work by a qual-
ified technician to restore the TV/VCR/DVD to its normal
operation.
14.Lightning - For added protection for this TV/VCR/DVD
receiver during a lightning storm, or when it is left unat-
tended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable sys-
tem. This will prevent damage to the TV/VCR/DVD due to
lightning and power-line surges.
e. If the TV/VCR/DVD has been dropped or damaged in
any way.
15.Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light of power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touch-
ing such power lines or circuits as contact with them might
be fatal.
f. When the TV/VCR/DVD exhibits a distinct change in
performance-this indicates a need for service.
20.Replacement Parts - When replacement parts are
required, be sure the service technician uses replacement
parts specified by the manufacturer that have the same
characteristics as the original part. Unauthorized substitu-
tions may result in fire, electric shock, injury to persons or
other hazards.
16.Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry - Never push objects of any kind
into this TV/VCR/DVD through openings as they may
touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the TV/VCR/DVD.
21.Safety Check - Upon completion of any service or repairs
to this TV/VCR/DVD, ask the service technician to perform
routine safety checks to determine that the TV/VCR/DVD
is in proper operating condition.
22.Heat - This TV/VCR/DVD product should be situated away
from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that pro-
duce heat.
18.Servicing - Do not attempt to service this TV/VCR/DVD
yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RECAUTIONS
P
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Este aparato digital de la Clase B cumple con la norma ICES-003 de Canadá.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equip-
ment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service
this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.
DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
LOCATION
For safe operation and satisfactory performance of your TV/VCR/DVD, keep the following in mind when
selecting a place for its installation:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the
top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the TV/VCR/DVD near strong magnetic fields.
• Avoid moving TV/VCR/DVD to locations where temperature differences are extreme.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to a
Authorized Service Center for servicing.
• Do not put your fingers or objects into the TV/VCR/DVD disc loading tray or the cassette compartment.
• Do not place anything directly on top of the unit.
MOISTURE CONDENSATION WARNING
• Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or
after heating a cold room or under conditions of high humidity. Do not use this unit at least for 2 hours until
its inside gets dry.
REGARDING THIS MANUAL
• Product and company names appearing within this manual are trademarks or registered trademarks of their
respective owners.
• Although special care has been taken to ensure that all information contained within this manual is correct
at time of writing, the information is subject to change without notice.
• Make sure to read the manual carefully and follow all instructions contained within. We will not be held
responsible for any damages caused by improper use or handling of this product.
• Reproducing this manual by any means, in whole or in part, is prohibited.
A NOTE ABOUT RECYCLING
This product's packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
The serial number of this product may be found on the back of this unit. No other TV/VCR/DVD has the same
serial number as yours. You should record the number and other vital information here and retain this book
as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase
Dealer
Dealer Phone No.
Model No.
Dealer Address
Serial No.
YMBOLS USED IN THIS MANUAL
S
The following is the description for the symbols used in this manual.
DVD-V
MP3
VCR
: Refers to DVD video discs.
: Refers to DVD-RW in Video mode.
: Refers to DVD-RW in VR mode.
: Refers to DVD-R discs.
: Refers to CD-R/RW discs with MP3
files.
DVD-RW (Video)
DVD-RW (VR)
DVD-R
: Refers to VHS tapes. Use only cas-
settes marked
.
CD
: Refers to Audio CDs.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ONTENTS
C
Repeat/Random/Program Play . . . . . . . . . . . . . . . .40
Repeat Play. . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Random Play. . . . . . . . . . . . . . . . . . . . . . . . . . 40
Program Play. . . . . . . . . . . . . . . . . . . . . . . . . . 41
Selecting AUDIO / VIDEO Menu . . . . . . . . . . . . . .41
Switching Audio Soundtrack. . . . . . . . . . . . . . . 41
Switching Subtitles . . . . . . . . . . . . . . . . . . . . . 43
Switching Camera Angles . . . . . . . . . . . . . . . . 43
Reducing Block Noise . . . . . . . . . . . . . . . . . . . 44
Virtual Surround Setting. . . . . . . . . . . . . . . . . . 44
GUIDE TO DISPLAYS ON SCREEN MENU . . . .45
EASY DVD RECORDING . . . . . . . . . . . . . . . . .46
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . .48
About DVD Recording . . . . . . . . . . . . . . . . . . . . . .48
Video mode/VR (Video Recording) mode. . . . . 48
Recording Speed . . . . . . . . . . . . . . . . . . . . . . 48
Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Copy Control . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Format Setting. . . . . . . . . . . . . . . . . . . . . . . . . 49
Reformatting . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Basic Recording . . . . . . . . . . . . . . . . . . . . . . . . . .51
Recording TV Programs. . . . . . . . . . . . . . . . . . 51
Checking the recording picture quality . . . . . . . 52
One-Touch Timer Recording . . . . . . . . . . . . . . . . .53
Finalizing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Protecting Discs . . . . . . . . . . . . . . . . . . . . . . . . . .55
Connecting to External Video Products . . . . . . . . .56
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Recording from External Video Products . . . . . 56
DUBBING . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
TIMER RECORDING . . . . . . . . . . . . . . . . . . . .58
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . .58
Suggestions for Timer Recording . . . . . . . . . . 60
EDITING DISCS . . . . . . . . . . . . . . . . . . . . . . . .61
About Disc Editing . . . . . . . . . . . . . . . . . . . . . . . . .61
Title List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Editing in Video Mode . . . . . . . . . . . . . . . . . . . 61
Editing in VR Mode . . . . . . . . . . . . . . . . . . . . . 61
Editing Discs in Video Mode . . . . . . . . . . . . . . . . .62
Deleting Titles . . . . . . . . . . . . . . . . . . . . . . . . . 62
Naming Titles . . . . . . . . . . . . . . . . . . . . . . . . . 63
Setting Chapter Markers . . . . . . . . . . . . . . . . . 63
Editing DVD-RW Discs in VR Mode(Original) . . . . .64
Deleting Titles . . . . . . . . . . . . . . . . . . . . . . . . . 64
Deleting Parts of Titles. . . . . . . . . . . . . . . . . . . 65
Naming Titles . . . . . . . . . . . . . . . . . . . . . . . . . 65
Setting Chapter Markers . . . . . . . . . . . . . . . . . 66
Setting Pictures for Thumbnails . . . . . . . . . . . . 66
Protecting Titles . . . . . . . . . . . . . . . . . . . . . . . 67
Releasing Title Protect. . . . . . . . . . . . . . . . . . . 67
Editing DVD-RW Discs in VR Mode(Playlist) . . . . . .68
Deleting Titles . . . . . . . . . . . . . . . . . . . . . . . . . 68
Deleting Parts of Titles. . . . . . . . . . . . . . . . . . . 69
Naming Titles . . . . . . . . . . . . . . . . . . . . . . . . . 69
Setting Chapter Markers . . . . . . . . . . . . . . . . . 70
Setting Pictures for Thumbnails . . . . . . . . . . . . 70
Adding Titles to Playlist . . . . . . . . . . . . . . . . . . 71
Deleting Playlist. . . . . . . . . . . . . . . . . . . . . . . . 71
PARENTAL LOCK LEVEL SETTING . . . . . . . . .72
IMPORTANT SAFETY INSTRUCTIONS . . . . . . .2
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .4
SYMBOLS USED IN THIS MANUAL . . . . . . . . . .5
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
COMPONENT NAMES . . . . . . . . . . . . . . . . . . . .7
Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . .8
Inserting Remote Control Batteries . . . . . . . . . . 9
Remote Control Range . . . . . . . . . . . . . . . . . . . 9
CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . .10
Connection of Main Unit . . . . . . . . . . . . . . . . . . . .10
Connection to Cable Box or Satellite Box . . . . . . . .10
Connection to Audio System . . . . . . . . . . . . . . . . .11
Audio Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
OSD DISPLAY SETTING . . . . . . . . . . . . . . . . . .14
OSD LANGUAGE SETTING . . . . . . . . . . . . . . .15
CHANNEL SETTING . . . . . . . . . . . . . . . . . . . . .16
Auto Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Add/Delete Function . . . . . . . . . . . . . . . . . . . . . . .17
Selecting TV Stereo or SAP . . . . . . . . . . . . . . . . . .17
CLOCK SETTING . . . . . . . . . . . . . . . . . . . . . . .18
Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . .18
Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . .19
DAYLIGHT SAVING TIME . . . . . . . . . . . . . . . . .20
SELECTING TV DISPLAY MODE . . . . . . . . . . .21
GUIDE TO DISPLAY MENUS . . . . . . . . . . . . . .21
OPERATING TV
TV FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . .22
Watching TV Program . . . . . . . . . . . . . . . . . . . . . .22
Setting Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . .22
Adjusting Picture . . . . . . . . . . . . . . . . . . . . . . . . . .23
Setting V-CHIP . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Setting MPAA Rating . . . . . . . . . . . . . . . . . . . . 24
Setting TV Rating . . . . . . . . . . . . . . . . . . . . . . 25
Setting V-CHIP Sub Ratings. . . . . . . . . . . . . . . 25
Setting V-CHIP Access Code. . . . . . . . . . . . . . 26
Selecting Closed Caption . . . . . . . . . . . . . . . . . . . .27
OPERATING VCR
VCR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . .28
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Normal Recording . . . . . . . . . . . . . . . . . . . . . . 28
One-Touch Timer Recording . . . . . . . . . . . . . . 29
Guide to Displays . . . . . . . . . . . . . . . . . . . . . . . . .29
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Other Functions . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Auto Rewind-Eject . . . . . . . . . . . . . . . . . . . . . . 30
OPERATING DVD RECORDER
PLAYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
About DVD Playing . . . . . . . . . . . . . . . . . . . . . . . .31
Guide to Displays . . . . . . . . . . . . . . . . . . . . . . 31
Language Setting . . . . . . . . . . . . . . . . . . . . . . . . .32
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Playback with Disc Menu. . . . . . . . . . . . . . . . . 35
Playback with Title Menu . . . . . . . . . . . . . . . . . 35
Special Playback . . . . . . . . . . . . . . . . . . . . . . . . . .36
Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Fast Forward / Fast Reverse . . . . . . . . . . . . . . 36
Slow Forward / Slow Reverse . . . . . . . . . . . . . 36
Step by Step . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Setting Marker . . . . . . . . . . . . . . . . . . . . . . . . 38
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Title/Chapter Search . . . . . . . . . . . . . . . . . . . . 38
Track Search . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CHANGING SETUP MENU
SETUP MENU LIST . . . . . . . . . . . . . . . . . . . . .73
OTHERS
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . .74
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . .78
LANGUAGE CODE . . . . . . . . . . . . . . . . . . . . .78
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . .79
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . .80
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . .82
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OMPONENT NAMES
C
Main Unit
1
13
2
Front
3
4
5
6
7
8
9 10 11 12
14
15 16 17 18 19 20 21
22
0
0
0
1
2
3
Cassette compartment (VCR): Insert a tape here.
12 RECORD indicator (VCR): Blinks during VCR
recording.
Disc tray (DVD): Place a disc on the tray when open.
13 DUBBING button (VCR➔DVD): Press to start VCR to
S-VIDEO input jack (DVD only): Use to connect the
S-Video output of external video components with an
S-Video cable.
DVD duplication.
14 VCR/DVD indicator: Shows the operating status.
Indicator for VCR illuminates during VCR playing and
one for DVD illuminates during DVD playing.
04
05
06
07
VIDEO input jack: Use to connect external video
components with a standard video cable.
K
L
15 CHANNEL
/
buttons: Press to change the chan-
AUDIO (L/R) input jack: Use to connect external
video/audio components with standard audio cables.
nel up or down. During DVD playback, press to
change the DVD chapter.
Receiving window for remote control signal:
Sensor that receives signal from the remote control unit.
16
C
STOP button (DVD): Press to stop playback or record-
ing. Press to stop the proceeding timer recording in DVD.
POWER button: Press to turn the unit on and off.
If timer programmings have been set, press to set the
unit in timer-standby mode. Press to cancel the timer-
standby mode, then turn the unit on.
17 B PLAY button (DVD): Press to start or resume play.
18 I RECORD button (DVD): Press once to start
recording. Press repeatedly to start a One-Touch
Recording.
K L
/
0
8
9
VOLUME
level.
buttons: Press to adjust the sound
19 RECORD indicator (DVD): Illuminates when you
have programmed the DVD or VCR timer recording
and blinks during DVD recording.
0
C STOP/A EJECT button (VCR):
A EJECT button- Press to remove the tape from the
unit.
C STOP button- Press to stop tape movement. Press
to stop the proceeding timer recording in VCR.
20 DUBBING button (VCR DVD): Press to start DVD to
VCR duplication.
21 A OPEN/CLOSE button (DVD): Press to open or
10 B PLAY button (VCR): Press to start playback.
close the disc tray.
11 I RECORD button (VCR): Press once to begin
recording. Press repeatedly to start a One-Touch
Recording.
22 HEADPHONE jack: To connect headphone (not sup-
plied) for personal listening.
Rear
AUDIO OUT
COAXIAL
1
2
3
1
AUDIO OUT COAXIAL jack (DVD sound only):
Use to connect an AV receiver with a coaxial digital
input jack.
• Only DVD, CD and MP3 audio will be output from
this jack.
2
3
AC Power Cord: Connect to a standard AC outlet to
supply power to this unit.
ANT. (Antenna input) jack: Use to connect an anten-
na, or cable system.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT NAMES
Remote Control Unit
15 MUTE button: Press to eliminate the sound temporarily.
14
15
K
L
16 CHANNEL
/
buttons: Press to change the chan-
1
2
nel up and down.
buttons: During DVD playback, press to
change the DVD chapter.
G
H
/
16
3
Press to adjust the video tape playback tracking man-
ually.
17
18
X
Y
17 VOLUME
/
buttons: Press to adjust the sound
4
5
6
level.
19
18 TIMER PROG. button: Press to display the timer
20
21
program setting menu.
19 DISC MENU button (DVD): Press to display the Disc
7
menu.
22
23
24
26
Press to change "Original" and "Playlist". (VR mode
only)
8
9
25
27
20 CLEAR button:
10
11
28
• During DVD operation
29
30
Press to clear the password once entered, to cancel
the programming for CD, to clear the selecting
marker number in the marker setup mode or to
clear the program once entered in the timer record-
ing setting mode, etc.
12
13
• During VCR operation
Press to reset the tape counter.
0
1
POWER button: Press to turn the unit on and off. If
timer programmings have been set, press to place the
unit in timer-standby mode. Press to cancel the timer
standby mode, then turn the unit on.
K L
/
21
/s /B buttons: Press to select items or settings.
22 REC MONITOR button (DVD): Press to check the
video to be recorded before attempting.
0
2
3
DISPLAY button: Press to display or change the on-
screen display.
23 RETURN button: Press to return to the previously
displayed menu screen.
0
Number button: Press to select channel numbers.
Press to select a title/chapter/track. Also press to
enter values for the settings in the SETUP menu.
24 PLAY B (DVD) button: Press to start or resume play.
25 STOP C (DVD) button: Press to stop playback or recording.
04
05
06
07
08
PICTURE button: Press to adjust the picture.
SETUP button: Press to display the setup menu.
TOP MENU button (DVD): Press to display the top menu.
ENTER button: Press to confirm or select menu items.
26 REW E button:
• During DVD operation
During playback, press to fast reverse. During
pause, press to play slow reverse.
• During VCR operation
Press to rewind the tape or to view the picture
rapidly in reverse during the playback mode.
REC SPEED button: Press to switch DVD REC
MODE or VCR REC SPEED.
27 F.FWD D button:
0
9 DVD RECORD button: Press once to start a
• During DVD operation
recording.
During playback, press to play fast forward.
During pause, press to play slow forward.
• During VCR operation
Press to rapidly advance the tape or view the pic-
ture rapidly in forward during playback.
10 VCR AUDIO button: During playback a HiFi video tape,
press to change the audio out setting "HIFI" or "MONO."
11 TIME SEARCH button (VCR): Press to call up the
time search menu.
12 VCR RECORD button: Press once to start a
28 PAUSE F button: Press to pause or recording.
29 STOP C (VCR) button: Press to stop playback or recording.
30 PLAY B (VCR) button: Press to start playback.
recording.
13 DUBBING button:
Press VCR
Press VCR
DVD to start dubbing from video tape to DVD.
DVD to start dubbing from DVD to video tape.
14 SLEEP button: Press to activate the sleep timer.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting Remote Control Batteries
1 Slide the cover of the remote control unit down
3 Slide and close the cover of the remote control
until the battery compartment appears.
unit.
2 Insert two AA size batteries, making sure that
their polarities should match the symbols shown
inside the battery casing.
NOTE
• Do not insert old and new batteries mixed together.
• Do not insert different brands or types of batteries
mixed together.
• Always insert new batteries for replacement.
Remote Control Range
Operate the remote control within 30-degree angle
on both sides of the infrared sensor on the main
unit. You can operate the remote control from a dis-
tance of several feet away from the main unit.
NOTE:
Other devices that use infrared beams, sunlight, fluores-
cent lights may affect the range and effectiveness of the
remote control. Make sure that this unit should be posi-
tioned where there is the minimum interference from
other devices.
Approximately
16.5 feet (5 m)
Within 30 degrees
Within 30 degrees
Approximately
22.8 feet (7 m)
Approximately
16.5 feet (5 m)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ONNECTIONS
C
Connection of Main Unit
Antenna
Cable
Signal
or
1
Connect
L
(Rear of main unit)
2
Plug in the AC power cord of this unit.
Connection to Cable Box or Satellite Box
(Cable box or
Satellite box)
IN
OUT
Cable
Signal
DO U
C
(Rear of main unit)
Select this connection when you want to view or record a scrambled channel. With this connection, channels
cannot be changed on the TV/VCR/DVD unit. You can view or record ONLY the channels you have selected
on the cable box or the satellite box.
• While you are recording, only the recorded channel can be viewed.
To select channels of the cable box or satellite box
K L
/
1) Turn on this unit by pressing POWER button. Then, press the CHANNEL
buttons to select channel 3
or 4 (the same channel as the output channel of the cable box or satellite box).
2) At the cable box or satellite box, select the channel you want to view or record.
Note for the Cable TV System Installer:
This reminder is provided to call the Cable TV system installer's attention to Article 820-40 of the National Electrical Code, which pro-
vides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the
building as close to the point of cable entry as possible.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to Audio System
• Before changing the connections or installing the unit, all devices should be turned off.
• Refer to each owner's manual for further information on other devices.
Receiver with Dolby Digital decoder
COAXIAL
Digital audio
input jack
Audio Coaxial Digital cable
(available wherever consumer
electronics are sold)
AUDIO OUT
COAXIAL
AUDIO OUT
COAXIAL
(digital)
A
U
D
I
O
O
U
T
COAXIAL
NOTE:
• When you play a DVD disc with connecting TV/VCR/DVD to a receiver with a Dolby Digital decoder, set "Dolby Digital" to "Stream" for
the "Digital Out" setting in the SETUP menu. (Refer to pages 12-13.)
• The audio source on a DVD disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or DAT
deck.
• If the receiver does not have a Dolby Digital decoder, set "Dolby Digital" to "PCM" for the "Digital Out" setting in the SETUP menu.
Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to pages 12-13.)
• Set "Dolby Digital" to "PCM" for the "Digital Out" setting in the SETUP menu for connecting to an MD deck or DAT deck. (Refer to
pages 12-13.)
• By hooking this unit up to a Multi-channel receiver with a Dolby Digital decoder, you can enjoy high-quality Dolby Digital 5.1 channel
surround sound as heard in the movie theaters.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trade-
marks of Dolby Laboratories.
NOTE:
• Only DVD, CD and MP3 audio will be available at the AUDIO OUT COAXIAL jack.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Digital Out
Audio Setting
Set the digital audio output.
Choose the appropriate audio setting when con-
necting the unit to an external audio system (sold
separately).
Setup > Playback
DVD
TV Mode
4:3 Letter Box
All
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
NOTE: DVD & CD Audio Only
• Only DVD and CD audio will be available to be amplified
through the external audio system.
Dynamic Range Control
Fast Forward with Audio
ON
OFF
NOTE:
• Dynamic Range Control function is available only with discs
recorded in the Dolby Digital format.
Setup > Playback
DVD
K
L
• Select a setting using
/
TV Mode
4:3 Letter Box
All
buttons, then press ENTER
Parental Lock
POWER
SETUP
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
button.
PCM
Dolby Digital
Option window will appear.
Proceed to step [A] or [B].
Dynamic Range Control
Fast Forward with Audio
OFF
[A] Settings for PCM (Default: Auto)
/
/
/
Original
OFF
ENTER
PCAuto
STOP C (DVD)
48kHz
96kHz
ntrol
udio
Dol
STOP C (VCR)
K L
/
• Select a setting using
ENTER button.
buttons, then press
Press STOP C (DVD) or STOP C (VCR) button
if you are playing a disc or tape.
Your setting will be activated.
Auto : Select "Auto" for normal playback.
1 Press POWER button to turn on the unit.
48kHz : If your amplifier/receiver is NOT compati-
ble with 96kHz PCM, select "48kHz".
2
Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
96kHz sound will be output in 48kHz.
s
B
3 Select "SETUP" using
/
buttons, then press
96kHz : If your amplifier/receiver is compatible
with 96kHz PCM, select "96kHz".
96kHz sound will be output.
ENTER button.
SETUP menu will appear.
NOTE:
K
L
s
B
4 Select "Playback" using / / / buttons, then
When playing disc with copyright protection
press ENTER button.
• If you select "Auto", the sound will be down sampled at 48kHz.
• If you select "96kHz", no digital sound will be output. Select
"Auto", so that outputting 48kHz digital sound.
Option window will appear.
K L
/
5 Select a desired item using
buttons, then
press ENTER button.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
[B] Settings for Dolby Digital (Default : Stream)
Fast Forward with Audio (Default : OFF)
Set to “ON” to hear the sound during playback in
fast forward of x2.
Original
OFF
PCM
Setup > Playback
DVD
ntrol
udio
Do
PCM
Stream
TV Mode
4:3 Letter Box
All
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
Dynamic Range Control
Fast Forward with Audio
ON
K L
/
• Select a setting using
buttons, then press
OFF
ENTER button.
Your setting will be activated.
PCM : Convert the Dolby Digital into PCM 2
channel (stereo).
Setup > Playback
DVD
K
L
• Select a setting using
/
TV Mode
4:3 Letter Box
All
buttons, then press ENTER
Parental Lock
When your amplifier/receiver is NOT
compatible with Dolby Digital, set to
"PCM".
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
button.
Your setting will be activated.
Dynamic Range Control
Fast Forward with Audio
ON
ON
OFF
O
Stream : Outputs a Dolby Digital signal.
When your amplifier has a Dolby Digital
decoder, set to "Stream".
6 Press SETUP button to exit SETUP menu.
NOTE:
When playing a DVD-RW disc recorded in VR mode
• If the audio source on a disc is Dolby Digital format, set
"Dolby Digital" to "PCM" so that you can switch to main (L),
sub audio (R), or a mix of both (L/R) with your
amplifier/decoder.
Dynamic Range Control (Default : ON)
Set to “ON” to compress the range between soft
and loud sounds.
Setup > Playback
DVD
TV Mode
4:3 Letter Box
All
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
Dynamic Range Control
Fast Forward with Audio
ON
OFF
Setup > Playback
DVD
K
L
• Select a setting using
/
TV Mode
4:3 Letter Box
All
buttons, then press ENTER
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
button.
Your setting will be activated.
ON
O
Dynamic Range Control
Fast Forward with Audio
OFF
OFF
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SD DISPLAY SETTING
O
OSD Background Color (Default : 1 Green)
POWER
Set the OSD screen color.
You can choose one from 1(Green), 2(Blue), and
3(Red).
Setup > Display
VCR DVD
SETUP
OSD Background Transparency 35%
OSD Background Color
OSD Language
Screen Saver
Caption
1
/
/
/
English
10 minutes
OFF
V-CHIP Setup
ENTER
STOP C (DVD)
STOP C (VCR)
Setup > Display
VCR DVD
K L
/
• Select a setting using
OSD Background Transparency 35%
Press STOP C (DVD) or STOP C (VCR) button
if you are playing a disc or tape.
buttons, then press ENTER
button.
OSD Background Color
OSD Language
Screen Saver
Caption
1
2
3
10 minutes
OFF
V-CHIP Setup
Your setting will be activated.
1 Press POWER button to turn on the unit.
2 Press SETUP button to display SETUP/DISC
menu.
Screen Saver (Default : 10 minutes)
SETUP/DISC menu will appear.
Set the time before the screen saver appears on
the screen.
s
B
3 Select "SETUP" using
/
buttons, then press
ENTER button.
Setup > Display
VCR DVD
SETUP menu will appear.
OSD Background Transparency 35%
OSD Background Color
OSD Language
Screen Saver
Caption
1
English
10 minutes
OFF
K
L
s
B
4 Select "Display" using / / / buttons, then
V-CHIP Setup
press ENTER button.
Option window will appear.
K L
/
5 Select a desired item using
buttons, then
press ENTER button.
Setup > Display
VCR DVD
K L
/
• Select a setting using
OSD Background Transparency 35%
buttons, then press ENTER
button.
OSD Background Color
OSD Language
Screen Saver
Caption
1
OFF
5 minutes
OSD Background Transparency (Default : 35%)
Set the background transparency of OSD screen.
You can choose between 0% through 100%.
10 minutes
s
15 minutes
30 minutes
V-CHIP Setup
Your setting will be activated.
Setup > Display
VCR DVD
OSD Background Transparency 35%
6 Press SETUP button to exit SETUP menu.
OSD Background Color
OSD Language
Screen Saver
Caption
1
English
10 minutes
OFF
V-CHIP Setup
Setup > Display
VCR DVD
K L
/
• Select a setting using
100%
OSD Background Transparency 3
85%
70%
50%
buttons, then press ENTER
button.
OSD Background Color
OSD Language
Screen Saver
Caption
1
E
1s
35%
25%
10%
0%
V-CHIP Setup
Your setting will be activated.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SD LANGUAGE SETTING
O
You can select the language for on-screen display
(OSD).
POWER
SETUP
/
/
/
ENTER
1 Press POWER button to turn on the unit.
2 Press SETUP button to display SETUP/DISC
menu.
SETUP/DISC menu will appear.
s
B
3 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
K
L
s
B
4 Select "Display" using / / / buttons, then
press ENTER button.
Option window will appear.
K L
/
5 Select "OSD Language" using
buttons, then
press ENTER button.
NOTE:
• Default OSD language setting is English.
6 Select your desired language among "English",
K L
/
"Français" and "Español" using
buttons,
then press ENTER button.
Your language setting will be activated.
Setup > Display
VCR DVD
OSD Background Transparency 35%
OSD Background Color
OSD Language
Screen Saver
Caption
1
English
Français
s
Español
OFF
V-CHIP Setup
7 Press SETUP button to exit SETUP menu.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HANNEL SETTING
C
It is recommended that you should preset channels
in your area using "Auto Preset" in the Channel
Preset of the SETUP menu.
5 Press SETUP button to exit.
You can select only the channels memorized in
K L
/
this unit by using the CHANNEL
buttons.
Auto Preset
NOTE:
K L
/
• If CHANNEL
buttons does not allow you to select chan-
nels after presetting, try Auto Preset again.
To select a channel :
K
L
CHANNEL
/
You can select a channel by directly entering
channel using the Number buttons on the
remote control.
Number
SETUP
Notes for using the Number buttons:
• When selecting cable channels which are higher than 99,
enter channel numbers as a three-digit number. (For exam-
ple: 117, press 1,1,7)
/
/
/
ENTER
RETURN
• You must precede single-digit channel numbers with a zero
(For example: 02, 03, 04 and so on).
• You can select the line input mode (“AUX”). To select “AUX”
by pressing [0], [0]. Details are on page 56.
1 Press SETUP button to display SETUP/DISC
menu.
SETUP/DISC menu will appear.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
K
L
s
B
3 Select "Channel" using / / / buttons, then
press ENTER button.
Channel Preset menu will appear.
K L
/
4 Select "Auto Preset" using
buttons, then
press ENTER button.
The unit will begin scanning channels available
in your area.
To cancel the Auto Preset during scanning:
Press RETURN button or SETUP button to cancel.
CH 18
Auto Presetting Now
NOTES:
• If the Auto Preset is cancelled before completing the preset,
some channels that have not been preset may not be available.
• The selection will depend on how you receive the TV channels.
• Be sure to have some type of reception, cable or antenna
connected to the TV before presetting channels.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Add/Delete Function
The next channel number will appear so that you
can continue adding or deleting channels.
The channels you no longer receive or seldom
watch can be deleted from the memory. You can
also add channels into memory.
7 Press SETUP button to exit.
Selecting TV Stereo or SAP
SETUP
You can select stereo or SAP (Secondary Audio
Program). "Stereo" has been selected as the default.
/
/
/
ENTER
SETUP
/
/
/
1 Press SETUP button to display SETUP/DISC menu.
ENTER
SETUP/DISC menu will appear.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
1 Press SETUP button to display SETUP/DISC menu.
SETUP/DISC menu will appear.
K
L
s
B
3 Select "Channel" using / / / buttons, then
press ENTER button.
s
B
2 Select "SETUP" using
/
buttons, then press
Channel Preset menu will appear.
ENTER button.
SETUP menu will appear.
K
L
4 Select "Manual Preset" using
/
buttons, then
press ENTER button.
K
L
s
B
3 Select "Channel" using / / / buttons, then
Manual Preset menu will appear.
press ENTER button.
Setup > Channel Preset > Manual Preset
Channel Preset menu will appear.
CH2
Add
Delete
K L
/
4 Select "TV Audio Select" using
buttons,
then press ENTER button.
Option window will appear.
Setup > Channel Preset VCR DVD
Auto Preset
5 To select the channel to add or delete;
Manual Preset
TV Audio Select
Stereo
SAP
s
Press button to move to a lower channel number.
B
Press button to move to a higher channel
number.
Setup > Channel Preset > Manual Preset
K L
/
5 Select "Stereo" or "SAP" using
buttons,
then press ENTER button.
CH18
Add
Delete
Stereo:
Outputs main-audio.
SAP: (Secondary Audio Program)
Outputs second audio channel. Refer to the item
in "Glossary" on page 79 for more information.
K L
/
6 Select "Add" or "Delete" using
buttons, then
press ENTER button.
The channel number will be added or deleted
from the channel memory.
6 Press SETUP button to exit.
K L
/
To view TV channels, press CHANNEL
buttons.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCK SETTING
C
Set the clock before you try timer recording. If a
Public Broadcasting Station (PBS) is available in
your area, follow Auto Clock Setting below. If not,
follow Manual Clock Setting on page 19.
K L
/
5 Select "Manual" using
buttons, then press
ENTER button.
Enter your PBS channel number using Number
Important
K
L
buttons or
ton.
/
buttons, then press ENTER but-
You must know the local PBS station in your area.
Auto Clock Setting
Setup > Clock
VCR DVD
Clock Setting
Set Channel No.
Auto Clock Setting
Daylight Saving Time
CH1
NOTE:
• Make sure that the antenna or cable are connected to the
unit.
• If the TV/VCR/DVD is connected directly to a cable converter
box or satellite box, the local PBS station must be selected
on the cable box itself, and the TV/VCR/DVD must be set to
the output channel of the cable converter box or satellite box
(usually channel 3 or 4), to be able to set up or correct the
clock automatically.
6 Press SETUP button to exit.
7 Press POWER button to turn off the unit.
This unit will search for the time when the power
is off. Leave it off for several minutes to give this
unit time to set the clock.
POWER
Number
NOTE:
• The clock may set itself automatically after you connect the
antenna/cable signal to this unit and plug in the power cord.
After setting, turn the power on to check the current time
appeared on the TV screen is correct.
SETUP
/
/
/
• If the current time is not displayed or the displayed clock is
not correct, set the clock manually.
ENTER
1 Press SETUP button to display SETUP/DISC
menu.
SETUP/DISC menu will appear.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
K
L
s
B
3 Select "Clock" using / / / buttons, then
press ENTER button.
Clock menu will appear.
K L
/
4 Select "Auto Clock Setting" using
buttons,
then press ENTER button.
Option window will appear.
Setup > Clock
VCR DVD
Clock Setting
Auto Clock Setting
Daylight Saving Time
OFF
Manual
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup > Clock
VCR DVD
Manual Clock Setting
Clock Setting
Auto Clock Setting
Daylight Saving Time
OFF
ON
JAN / 12 / 2004 (MON)
09 : 24 AM
SETUP
ENTER
NOTE:
/
/
/
• Your clock setting will be lost if either there is a power failure
or this unit has been unplugged for more than 3 seconds
when you set the clock manually.
K
L
7 Press
/
buttons to select AM or PM, then
press ENTER button.
Clock menu will appear. The settings will be acti-
vated.
1 Press SETUP button to display SETUP/DISC
menu.
Setup > Clock
VCR DVD
Clock Setting
SETUP/DISC menu will appear.
Auto Clock Setting
Daylight Saving Time
OFF
ON
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
8 Press SETUP button to exit.
K
L
s
B
3 Select "Clock" using / / / buttons, then
press ENTER button.
Although seconds are not displayed, they begin
counting from zero.
Clock menu will appear.
K
L
4 Select "Clock Setting" using
/
buttons, then
When "Auto Clock Setting" is changed to
"Manual", select "OFF" using the following
steps.
press ENTER button.
A clock setting window will appear.
Repeat steps [1] to [3] in "Manual Clock Setting".
Setup > Clock
VCR DVD
Clock Setting
Auto Clock Setting
Daylight Saving Time
OFF
ON
K L
/
4 Select "Auto Clock Setting" using
buttons,
- - - / - - / - - - - ( - - - )
- - : - -
then press ENTER button.
K L
/
5 Select "OFF" using
buttons, then press
ENTER button.
Press ENTER button.
Default date will appear.
6 Press SETUP button to exit.
K L
/
5 Enter the date (month / day / year) using
buttons.
s
B
Press
/
buttons to move the cursor.
Setup > Clock
VCR DVD
Clock Setting
Auto Clock Setting
Daylight Saving Time
OFF
ON
JAN / 12 / 2004 (MON)
12 : 00AM
K L
/
6 Enter the time (hour / minute) using
but-
tons.
s
B
Press
/
buttons to move the cursor.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
AYLIGHT SAVING TIME
D
When Daylight Saving Time is ON, the clock will
automatically move forward one hour on the first
Sunday in April and move back one hour on the last
Sunday in October.
SETUP
/
/
/
ENTER
1 Press SETUP button to display SETUP/DISC
menu.
SETUP/DISC menu will appear.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
K
L
s
B
3 Select "Clock" using / / / buttons, then
press ENTER button.
Clock menu will appear.
K L
/
4 Select "Daylight Saving Time" using
but-
tons, then press ENTER button.
Daylight Saving Time options will appear.
Setup > Clock
VCR DVD
Clock Setting
Auto Clock Setting
Daylight Saving Time
OFF
ON
OFF
K L
/
5 Select "ON" or "OFF" using
buttons, then
press ENTER button.
Choose "ON" when currently observing the day-
light saving time.
6 Press SETUP button to exit.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTING TV DISPLAY MODE
S
You can select the TV display mode to your viewing
preference for DVD viewing.
K
L
s
B
3 Select "Playback" using / / / buttons, then
press ENTER button.
"4:3 Letter Box" has been selected as the default.
Playback menu will appear.
K L
/
4 Select "TV Mode" using
buttons, then press
ENTER button.
SETUP
Option window will appear.
/
/
/
Setup > Playback
TV Mode
DVD
4:3 Letter Box
Parental Lock
4:3 Pan & Scan
ENTER
Disc Menu Language
Audio Language
English
Original
OFF
Subtitle Language
Digital Out
Dynamic Range Control
Fast Forward with Audio
ON
OFF
1 Press SETUP button to display SETUP/DISC
"4:3 Letter Box": black bars appear on the top
and bottom of the screen.
menu.
SETUP/DISC menu will appear.
"4:3 Pan & Scan" : full height picture with both
sides trimmed.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
K L
/
5 Select a desired option using
buttons, then
SETUP menu will appear.
press ENTER button.
6 Press SETUP button to exit.
UIDE TO DISPLAY MENUS
G
Every time you press DISPLAY button, the display will change as follows:
Press DISPLAY button.
Time and Channel display
12:00AM
Current
time
CH 21
Current
channel
number
DVD status display
Press DISPLAY button.
DVD-RW
1
1
0:00:00
Video mode
SP 1:25 Rem.
CH 21
For details, see page 31.
Press
DISPLAY
button.
Note:
This menu is available only when a disc is inserted into the unit.
DISC
C
VCR status display
Press DISPLAY button.
For details, see page 29.
VCR
SLP
C
COUNT
0:00:03
Press DISPLAY button.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING TV
V FUNCTIONS
T
Watching TV Program
Setting Sleep Timer
POWER
Number
SLEEP
K
X
L
Y
CHANNEL
/
VOLUME
/
The sleep timer function automatically turns off the
power at a specified time period.
1 Press POWER button to turn on the unit.
2 Select the desired channel using CHANNEL
1 Press SLEEP button.
K L
/
buttons or the Number buttons on the
Sleep timer menu will appear.
remote control.
If the TV/VCR/DVD is connected to a cable box
or satellite box, the TV/VCR/DVD must be on
channel 3 or channel 4, then the channel to be
viewed must be selected on the cable box or
satellite box.
SLEEP TIMER [OFF]
3 Adjust the volume to the desired listening level
X Y
/
using VOLUME
buttons.
2 Press SLEEP button repeatedly to change the
sleep time.
4 Adjust picture controls for a natural looking
The timer can be set up to 2 hours, by 30 min-
utes each time you press SLEEP button.
image. Refer to "Adjusting Picture" on page 23.
3 To cancel the sleep timer, press SLEEP button
repeatedly until "SLEEP TIMER [OFF]" is dis-
played.
Degaussing
Magnetism from nearby appliances and unshielded
speaker systems might affect the color of the TV
picture.
NOTE:
• If you disconnect the unit from the AC outlet, or if you have
a power failure, the sleep time setting will be lost.
If this happens, move this TV/VCR/DVD away from
the appliance. If the color is still not correct, unplug
the power cord, then plug it in again 30 minutes
later.
• This function does not operate during Recording mode.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Picture
The adjustments you can make are as follows:
PICTURE
/
/
/
BRIGHT
-
-
-
+
+
+
1 Press PICTURE button.
K
/
L
2 Select the setting item using
buttons.
CONTRAST
NOTE:
• You can use also PICTURE button to select the setting item.
s
B
Adjust using
/
buttons.
BRIGHT
CONTRAST
COLOR
TINT
to decrease brightness to increase brightness
to decrease contrast to increase contrast
COLOR
to pale
to brilliant
to green
to clear
to purple
SHARPNESS to soft
TINT
-
+
SHARPNESS
-
+
NOTE:
• In the above steps, the picture adjustment display will disap-
pear automatically in about 5 seconds if you do not press
any buttons.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING TV
TV FUNCTIONS
Setting V-CHIP
K L
/
4 Select "V-CHIP Setup" using
buttons, then
press ENTER button.
"ACCESS CODE" screen will appear.
Number
SETUP
ACCESS CODE
– – – –
/
/
/
ENTER
5 Enter the 4-digit access code using Number but-
tons.
The default access code is "0000". If you have
not set a personal access code, enter "0000".
V-CHIP enables parents to prevent their children
from watching inappropriate material on TV.
V-CHIP reads the ratings for programming (except
for news and sports programs, unedited movies on
premium cable channels and Emergency Broadcast
System signals), then denies access to program-
ming if the program's rating meets or exceeds the
limitations you select. In this case, a "PROTECTED
PROGRAM by..." message appears on the TV
screen.
K L
/
6 Select "MPAA RATING" using
buttons, then
press ENTER button.
- V-CHIP SET UP -
TV RATING
MPAA RATING
CHANGE CODE
To block certain ratings, follow the steps below.
K L
/
7 Select the desired limitation using
buttons.
NOTE:
• Programming may be rated by the Motion Picture Association of
America (MPAA) or according to the Television Parental
Guidelines. In order to block any inappropriate programming, set
your limits in both places (MPAA RATING and TV RATING).
G
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
PG
PG-13
R
• You cannot access the menu when the "PROTECTED PRO-
GRAM by..." message appears. In this case, change to an
unblocked channel, then press SETUP button.
NC-17
X
Setting MPAA Rating
Then press ENTER button to select [BLOCK] or
[VIEW].
1 Press SETUP button to display SETUP/DISC
NOTE:
• When you select a rating category and change it to
menu.
[BLOCK], all higher ratings will change to [BLOCK] automat-
ically. Also, the lower ratings will change to [VIEW] automati-
cally.
SETUP/DISC menu will appear.
s
B
2 Select "SETUP" using
/
buttons, then press
• When you turn "G" to [BLOCK] or [VIEW], all ratings will
change to [BLOCK] or [VIEW] automatically.
ENTER button.
SETUP menu will appear.
8 Press SETUP button to exit.
K
L
Rating Category Explanations
s
B
3 Select "Display" using / / / buttons, then
press ENTER button.
• G:
General Audience
Display menu will appear.
• PG:
Parental Guidance suggested.
• PG-13: Unsuitable for children under 13
• R:
Restricted; under 17 requires
accompanying
parent or adult guardian
• NC-17: No one under 17 admitted
• X: Mature audience only
24
Download from Www.Somanuals.com. All Manuals Search And Download.
• The sub ratings that are set to [BLOCK] appear next to the
rating category in TV RATING menu.
Setting TV Rating
• When you turn "TV-Y" to [BLOCK] or [VIEW], all ratings will
change to [BLOCK] or [VIEW] automatically.
1 Press SETUP button to display SETUP/DISC
menu.
8 Press SETUP button to exit.
SETUP/DISC menu will appear.
Rating Category Explanations
s
B
2 Select "SETUP" using
/
buttons, then press
• TV-Y:
Appropriate for all children
ENTER button.
• TV-Y7: Appropriate for children seven
and older
SETUP menu will appear.
• TV-G: General Audience
K
L
s
B
3 Select "Display" using / / / buttons, then
• TV-PG: Parental Guidance suggested.
• TV-14: Unsuitable for children under 14
• TV-MA: Mature audience only
press ENTER button.
Display menu will appear.
K L
/
4 Select "V-CHIP Setup" using
buttons, then
press ENTER button.
Setting V-CHIP Sub Ratings
"ACCESS CODE" screen will appear.
When you select TV-Y7, TV-PG, TV-14 or TV-MA
and press ENTER button, the sub-rating menu will
appear.
ACCESS CODE
– – – –
If you select the rating category (example: TV-PG)
and change it to [BLOCK] or [VIEW], the sub-rat-
ings (example: V for Violence) will change to
[BLOCK] or [VIEW] automatically.
You can set the sub-ratings to [BLOCK] or [VIEW]
individually when the rating category is set to
[BLOCK]. To set the sub-ratings individually, follow
the procedure below.
5 Enter the 4-digit access code using Number
buttons.
The default access code is "0000". If you have
not set a personal access code, enter "0000".
NOTE:
K L
/
6 Select "TV RATING" using
buttons, then
• When you select TV-Y7:
K
/
L
press ENTER button.
Select "FV" (Fantasy Violence) using
buttons.
- V-CHIP SET UP -
TV-Y7
FV
[BLOCK]
[BLOCK]
TV RATING
MPAA RATING
CHANGE CODE
Then, press ENTER button to select [BLOCK] or
[VIEW]. Press SETUP button to exit.
• When you select TV-PG, TV-14 or TV-MA:
Select "D" (Suggestive Dialog), "L" (Coarse Language),
K L
/
7 Select the desired limitation using
buttons.
TV-Y
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
K
/
L
TV-Y7
TV-G
"S" (Sexual Situation) or "V" (Violence) using
tons.
but-
TV-PG
TV-14
TV-MA
TV-PG
[BLOCK]
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Then press ENTER button to select [BLOCK] or
[VIEW].
NOTE:
• Refer to the next section, “Setting V-CHIP Sub Ratings” for
Press ENTER button to select [BLOCK] or [VIEW], then
press SETUP button to exit.
• When you select TV-MA, "D" will not appear.
the details about the sub-rating menu of TV-Y7, TV-PG, TV-
14 or TV-MA.
• When you select a rating category and change it to
[BLOCK], all higher ratings will change to [BLOCK] automat-
ically. Also, the lower ratings will change to [VIEW] automati-
cally.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING TV
TV FUNCTIONS
Setting V-CHIP Access Code
K L
/
6 Select "CHANGE CODE" using
buttons,
then press ENTER button.
- V-CHIP SET UP -
Number
SETUP
TV RATING
MPAA RATING
CHANGE CODE
/
/
/
The following screen will appear.
ENTER
NEW CODE
– – – –
CONFIR–M–CO–DE–
To change the access code, follow the procedure
below.
1 Press SETUP button to display SETUP/DISC
menu.
7 Enter the desired access code in NEW CODE
box using Number buttons, then enter the same
code in CONFIRM CODE box. Your new access
code is set. The display returns to "V-CHIP SET
UP" menu.
SETUP/DISC menu will appear.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
NOTE:
K
L
s
B
3 Select "Display" using / / / buttons, then
• If the code in CONFIRM CODE does not match the code in
NEW CODE, repeat step [7], making sure you enter exactly
the same new code in CONFIRM CODE box.
press ENTER button.
Display menu will appear.
• If a power failure occurs, the access code returns to the
default access code, "0000".
K L
/
4 Select "V-CHIP Setup" using
buttons, then
• If you connect the power cord to an AC outlet that is con-
trolled by a wall switch, the access code will be erased
every time you turn off the power at the wall switch. The
access code returns to the default access code.
press ENTER button.
"ACCESS CODE" screen will appear.
ACCESS CODE
8 Press SETUP button to exit.
– – – –
If You Forget Your Access Code
Return the access code to the default code,
"0000". To restore "0000" as the personal
access code, unplug the TV's power cord for 10
seconds, then plug it in again.
5 Enter the 4-digit access code using Number but-
tons.
The default access code is "0000". If you have
not set a personal access code, enter "0000".
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Closed Caption
SETUP
ENTER
/
/
/
You may view specially labeled (cc) TV programs,
movies, news, prerecorded tapes, etc. with either
dialogue captions or text added to the display.
1 Press SETUP button to display SETUP/DISC
menu.
SETUP/DISC menu will appear.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
SETUP menu will appear.
K
L
s
B
3 Select "Display" using / / / buttons, then
press ENTER button.
Display menu will appear.
K L
/
4 Select "Caption" using
buttons, then press
ENTER button.
Option window will appear.
Setup > Display
VCR
OSD Background Transparency 35%
OSD Background Color
OSD Language
Screen Saver
Caption
1
OFF
CAPTION 1
s
CAPTION 2
TEXT 1
TEXT 2
V-CHIP Setup
K L
/
5 Select a desired option using
buttons, then
press ENTER button.
Select “OFF” to cancel the closed caption sys-
tem.
6 Press SETUP button to exit.
NOTE:
• If the TV/VCR/DVD displays a black box on the TV screen,
this means that the TV/VCR/DVD is set to the TEXT mode.
To clear screen, select “CAPTION 1”, “CAPTION 2” or
“OFF”.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING VCR
CR FUNCTIONS
V
Playback
Recording
VCR
Normal Recording
VCR
POWER
Before recording, make sure:
K
L
CHANNEL
/
• Stereo or SAP is selected (page 17).
• The desired channel should be selected by press-
ing the Number buttons on the remote control or
K L
/
CHANNEL
buttons on the main unit.
•
•
A tape with a record tab should be loaded inside the unit.
/
/
/
The desired recording speed should be selected in SP
(standard play) or SLP (super long play) mode by
pressing REC SPEED button twice on the remote con-
K L
/
trol. Use
buttons to change the recording speed.
STOP C (VCR)
PLAY B (VCR)
•
Refer to page 58 for instructions on timer recording.
VCR
SP
C
1 Press POWER button on the remote control or
the main unit.
Recording speed:
2 Insert a prerecorded tape, then press PLAY
B
Tape speed
Type of tape
SP mode
Recording/PlaybackTime
(VCR) button to begin playback.
T60
T120
2hours
6hours
T160
2-2/3hours
8hours
1hour
3hours
NOTE:
SLP mode
• When a tape without the record tab is inserted, the unit will
start playback automatically.
• Tracking will be automatically adjusted upon playback. To
K
L
CHANNEL
/
K
L
adjust the tracking manually, press the CHANNEL
/
but-
Number
K
L
tons on the main unit or CHANNEL
/
buttons on the
remote control.
3 Press STOP C (VCR) button to stop playback.
4 Press C STOP/A EJECT button on the main
unit to eject the tape.
REC SPEED
PAUSE
VCR RECORD
F
STOP C (VCR)
1 Press VCR RECORD button to begin the recording.
To temporarily stop recording, press PAUSE F button.
Press VCR RECORD button to resume the recording.
When 5 minutes have passed since the unit entered
Pause mode, the recording will automatically stop.
2 Press STOP C (VCR) button when the recording
is completed.
Accidental erasure prevention
NOTES:
To prevent accidental recording
on a recorded cassette, remove
its record tab. To record on it
later,cover the hole with cello-
Record tab
phane tape.
• You can ONLY watch the same TV program that is being
recorded.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
One-Touch Timer Recording
Time Search
VCR
VCR
This feature allows you to set the recording length
simply by pressing I RECORD (VCR) button on the
main unit.
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish
to skip.
C STOP /
A EJECT
(VCR)
I RECORD
(VCR)
/
/
/
1 During normal recording, press I RECORD (VCR)
button on the main unit to begin one-touch timer
recording.
TIME SEARCH
You can select a fixed recording time by pressing
the I RECORD (VCR) button on the main unit
repeatedly.
1 Press TIME SEARCH button.
Time search menu will appear.
(0:30)
(1:00)
(Normal recording)
(8:00)
K L
/
2 Enter your desired time to skip using
but-
(7:30)
tons.
TIME SEARCH
2:50
When one-touch timer recording finishes, the
unit will turn off automatically.
To cancel the one-touch timer recording within
the specified time, press STOP C (VCR) button.
NOTE:
• If One-Touch Timer Recording finishes in VCR during play-
back or Record mode in DVD, the VCR will be in Stop mode
and the DVD keeps the current mode.
s
B
3 Press
/
buttons to start time search.
Forward or Reverse
B
If you want to move a tape forward, press but-
ton.
Guide to Displays
Press DISPLAY button repeatedly to bring up the
display for VCR status.
s
If you want to move a tape backward, press
button.
After time search, the unit will play the tape
automatically.
NOTES:
• Time Search function is not available during recording.
VCR
SLP
C
HIFI
COUNT
• To stop the time search, press STOP C (VCR) button at
step [3].
1
4
0:00:03
• To exit the time search menu, press RETURN button at
step [2].
2
3
• If a tape reaches to the end during the search, this unit
will cancel the search and rewind the tape.
1. Status of the current tape appears for 5 seconds
2. A recording speed appears for 5 seconds
3. Indicates a Tape Counter
4. Audio status of the played tape
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING VCR
VCR FUNCTIONS
• When you want to enjoy the sound in monaural,
select "MONO".
Other Functions
VCR
Your Selection
HIFI
MONO
Monaural
L+R
L-channel
R-channel
Type of recorded tape
non Hi-Fi tapes
Monaural
Monaural
K
L
CHANNEL
/
Hi-Fi tapes
recorded in
Hi-Fi stereo
L
R
Hi-Fi tapes
recorded main
audio program
Main audio
program
Main audio
program
Main audio
program
CLEAR
Hi-Fi tapes
recorded second
audio program
Second audio Second audio Second audio
program program program
STOP C (DVD)
E /
VCR AUDIO
D
PAUSE
F
Auto Rewind-Eject
To cue or review picture during playback
(Picture Search):
VCR
• When the end of a tape is reached during record-
ing, playback or fast-forward, the tape will auto-
matically rewind to the beginning. After rewinding
finishes, the TV/VCR/DVD will eject the tape.
Press g or h buttons during playback.
Press it again and the unit will search in super high
speed. (in the SLP mode only)
• The tape will not auto-rewind during timer
recording or One-Touch Timer Recording.
To freeze the picture on TV screen during play-
back (Still mode):
Press PAUSE F button. Each time you press the
button, the picture will move forward by one frame.
If the picture begins to vibrate vertically during the
still mode, stabilize the picture by pressing the
K L
/
CHANNEL
buttons.
Counter Reset:
Press CLEAR button. The counter appears on the
TV screen. Press CLEAR button again to reset.
To playback in slow motion:
Press PAUSE F button during playback, then press
D button. Playback in slow motion will start.
If noise bars appear on the TV screen, you can
K L
/
reduce them by pressing CHANNEL
buttons.
NOTE:
• Still/Slow/Pause mode will be automatically cancelled in 5
minutes to prevent damage to the tape and the video head.
• To return to playback from the Picture Search/Still/Slow mode,
press PLAY B (VCR) button.
When you playback a tape recorded in Hi-Fi
stereo:
Press VCR AUDIO button on the remote control to
select Hi-Fi or MONO for playback sound mode.
• When you want to enjoy the sound in stereo,
select "HIFI".
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
LAYING
P
About DVD Playing
Before you play DVD discs, read the following information.
Playable discs
Region codes
This unit is compatible to play the following discs.
This unit has been designed to play DVD discs with
Region One (1). DVDs must be labeled for ALL
regions or for Region 1 in order to play on this unit.
To play a DVD, make sure that it meets the requirements
for Region Codes and Color Systems as described below.
Discs with the following logos can be played on the unit.
Other Disc types are not guaranteed to play.
You cannot play DVDs labeled for other regions.
Make sure to check the symbols below on your
DVDs. If these region symbols are not found on your
DVD, you cannot play that DVD in this unit.
Color systems
Disc
Logo
DVDVIDEO
The number inside the globe refers to region of the
world. Region 1 represents the United States,
Canada, Bermuda, the U.S.Virgin Islands and small
regions near Australia.
DVD-RW (VIDEO/VR MODE)
DVD-R (VIDEO MODE)
A DVD labeled for a specific region can only play on
the unit with the same region code.
CD-DA (AUDIO CD)
DVD playback
The contents of DVD disc are generally divided into
titles. Titles may be further subdivided into chapters.
CD-R (CD-DA FORMAT, MP3 files)
CD-RW (CD-DA FORMAT, MP3 files)
Start Rec.
Title 1
Stop/Start
Stop Rec.
DVDs are recorded in different color systems
throughout the world. The most common color sys-
tems are NTSC (which are used primarily in the
United States and Canada), PAL and SECAM. This unit
uses NTSC, so DVDs you play must be recorded in
the NTSC system.You cannot play DVDs recorded in
other color systems.
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
Guide to Displays
Press DISPLAY button repeatedly to bring up the
display menu for DVD status. This menu will give
you the information on the playing disc. Some oper-
ations are available while disc is playing.
1. Indicates a disc type and a format mode.
2. Indicates a recording speed and possible record-
ing time left.
3. Indicates a current channel number.
NOTE:
4
1
4. Indicates a title number, chapter number and the
time elapsed of disc play.
This menu is available only
when a disc is inserted into
the unit.
DVD-RW
1
1
0:00:00
Video mode
5. Icon Legend:
SP 1:25 Rem.
CH 1
2
3
: Search
: Marker
5
: Audio
: Noise Reduction
: Zoom
: Subtitle
: Angle (except VR mode)
: Repeat
: Virtual Surround
DISC
C
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
PLAYING
Language Setting
Audio Language (Default : Original)
Set the Audio language.
NOTE:
• Only the languages supported by the disc can be selected.
Setup > Playback
DVD
TV Mode
4:3 Letter Box
All
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
Number
SETUP
Dynamic Range Control
Fast Forward with Audio
ON
OFF
/
/
/
Setup > Playback
DVD
K
L
• Select a setting using
/
ENTER
TV Mode
4:3 Letter Box
All
buttons, then press ENTER
Parental Lock
Original
STOP C (DVD)
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
button.
French
Spanish
Other
Your setting will be activated.
STOP C (VCR)
Dynamic Range Control
Fast Forward with Audio
ON
OFF
Press STOP C (DVD) or STOP C (VCR) button if
you are playing a disc or tape.
Subtitle Language (Default : OFF)
1 Press SETUP button to display SETUP/DISC
Set the subtitle language.
menu.
Setup > Playback
DVD
SETUP/DISC menu will appear.
TV Mode
4:3 Letter Box
All
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
Dynamic Range Control
Fast Forward with Audio
ON
OFF
SETUP menu will appear.
K
L
s
B
3 Select "Playback" using / / / buttons, then
press ENTER button.
Setup > Playback
DVD
K
L
• Select a setting using
/
Option window will appear.
TV Mode
4:3 Letter Box
All
buttons, then press ENTER
Parental Lock
OFF
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
K L
/
4 Select a desired item using
buttons, then
button.
French
Other
Spanish
press ENTER button.
Your setting will be activated.
Dynamic Range Control
Fast Forward with Audio
ON
OFF
NOTE:
• Audio Language setting may not be available to some discs.
• You can change or switch off the subtitles on a DVD disc
also from the disc menu if it is available.
If "Other" is selected, press 4-digit code using
Number buttons.
Disc Menu Language (Default : English)
Setup > Playback
TV Mode
4:3 Letter Box
All
Set the language for Disc Menu.
Parental Lock
English
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
French
Spanish
Setup > Playback
DVD
Other
TV Mode
4:3 Letter Box
All
Code Input
- - - -
Parental Lock
Dynamic Range Control
Fast Forward with Audio
ON
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
OFF
Dynamic Range Control
Fast Forward with Audio
ON
• When you finish entering the code, press
ENTER button. Refer to the language code
table on page 78.
OFF
5 Press SETUP button to exit SETUP menu.
Setup > Playback
DVD
K
L
• Select a setting using
buttons, then press
ENTER button.
/
TV Mode
4:3 Letter Box
All
Parental Lock
English
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
French
Spanish
Other
Your setting will be activated.
Dynamic Range Control
Fast Forward with Audio
ON
OFF
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Playback
VR mode:
Original
1
Playback
12
3
DVD-R DVD-RW (Video) DVD-RW (VR)
JAN/1 12:00AM
4
JAN/1 1:00AM
5
JAN/1 2:00AM
POWER
JAN/1 3:00AM
JAN/1 4:00AM
DISC MENU button
Playlist
1
12
3
TOP MENU
ENTER
DISC MENU
JAN/1 12:00AM
4
JAN/1 1:00AM
5
JAN/1 2:00AM
/
/
/
JAN/1 3:00AM
JAN/1 4:00AM
STOP C (DVD)
NOTE:
• Press the TOP MENU button to exit the menu.
• Disc menu is only available for VR mode recorded disc.
1 Press POWER button.
• For DVD-R (Video mode) and DVD-RW (Video mode) discs
which are already finalized, a title list will be displayed
instead of thumbnails as shown below.
A
2 Press OPEN/CLOSE button on the main unit
to open the disc tray.
Title Menu
The disc tray will open.
1
JAN/1 12:24AM CH96 XP
3 Place the disc onto the disc tray with its label
facing up and make sure to align the disc to the
A
disc tray guide. Press
OPEN/CLOSE button
again to close the disc tray.
NOTE:
K
L
s
B
5 Select a desired title using / / / buttons,
• This operation may take a few minutes to complete.
then press ENTER button.
• Some discs may start playing automatically.
Playback will start.
6 Press STOP C (DVD) button to stop playback.
NOTE:
disc
tray
guide
• You can resume play from where you stopped playing the
disc. (Resume play) Refer to page 36 for details about
resume play.
A
To eject the disc, press
OPEN/CLOSE button
4 Press TOP MENU button to display the title
to open the disc tray, then remove the disc
before turning off the unit.
menu.
You can change "Original" or "Playlist" of VR
mode using DISC MENU button.
Video mode:
Title List
1
12
3
JAN/1 12:00AM
4
JAN/1 1:00AM
5
JAN/1 2:00AM
JAN/1 3:00AM
JAN/1 4:00AM
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
PLAYING
DVD-V
CD
MP3
POWER
TOP MENU
ENTER
RETURN
STOP C (DVD)
1 In stop mode, press TOP MENU button to bring
up the MP3 menu.
PLAY B (DVD)
STOP C (DVD)
List of MP3 Files
DISC NAME
FOLDER NAME 1
FOLDER NAME 2
FOLDER NAME 3
FOLDER NAME 4
FOLDER NAME 5
FOLDER NAME 6
1 Press POWER button.
1
2
FILE NAME 1
FILE NAME 2
A
2 Press OPEN/CLOSE button on the main unit
1/2
to open the disc tray.
The disc tray will open.
To exit the menu, press TOP MENU button again.
NOTE:
3 Place the disc onto the disc tray with its label
facing up and make sure to align the disc to the
disc tray guide.
A
• If you press
OPEN/CLOSE button to close the disc tray,
the automatic playback will not start, but MP3 menu will
appear.
4 Press PLAY B (DVD) button to start playing.
K
L
2 Press
/
buttons to select a desired folder
(group) or track, then press ENTER button.
Playback will start.
When selecting track:
• If you are playing a DVD-Video disc, a menu
may appear.
Refer to page 35 for details about a disc menu.
Playback will start.
When selecting the folder:
The files in the folder will appear.
5 Press STOP C (DVD) button to stop playing.
K
L
Press or button to select the track or folder
NOTE:
• Some discs may start playing automatically.
you want, then press ENTER button.
s
• Press button or RETURN button to go to the
previous hierarchy.
• Press STOP C (DVD) button to return to the
first item.
Hints for MP3 files:
•
Folders are known as Groups, files are known as Tracks.
• Folders are accompanied by
• MP3 files are accompanied by
icon.
icon.
Playback will start from the selected track and go to
the next one in turn.
• The system can recognize up to 255 groups (or fold-
ers) and up to 255 tracks.
• The name of the group and track can be displayed in
up to 32 characters. Unrecognizable characters will
be replaced with asterisks.
•
If the folder includes no files, "No Files" will be displayed.
• The audio source of MP3 files cannot be recorded as
digital sound by an MD or DAT deck.
• Files whole extension other than ".mp3 (MP3)" will
not be listed in the MP3 menu.
• Some unplayable folders or tracks may be listed in the
MP3 menu due to the recording status.
This unit recommends the files recorded under the fol-
lowing circumstances:
• Sampling frequency: 44.1kHz or 48kHz.
• Constant bit rate: 112kbps - 320kbps.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback with Disc Menu
Playback with Title Menu
DVD-V
DVD-V
A DVD disc contains a disc menu that describes the
contents or allows you to customize the playback.
For example, the menu may offer choices for subti-
tle languages, special features, or chapter selection.
Some DVDs have a title menu, which lists the titles
available on them. It helps you to start playback at a
specific title.
Some disc menus are automatically displayed when
you start playback, others only appear when you
press DISC MENU button.
Number
TOP MENU
/
/
/
Number
ENTER
DISC MENU
/
/
/
1 Press TOP MENU button.
The title menu will appear.
NOTE:
ENTER
• The TOP MENU button will not always be active with all
DVDs.
1 Press DISC MENU button.
The DVD main menu will appear.
NOTE:
• Menus vary among discs. Refer to the information accompa-
nying the disc for details.
If the feature is not available,
the TV screen.
may appear on
• Menus vary among discs. Refer to the information accompa-
nying the disc for details.
If the feature is not available,
the TV screen.
may appear on
K
L
s
B
2 Select a title to play using the / / / buttons,
then press ENTER button.
Playback will begin at the title you selected.
K
L
s
B
2 Select an item using / / / buttons, then
TOP MENU button:
press ENTER button to confirm.
Displays the 'Title menu' of a DVD disc that
varies with the disc.
Continue this step to set up all the features you
want or to start playing the disc from the menu.
K
L
s
B
/ / / buttons:
DISC MENU button:
Moves the cursor on the screen.
ENTER button:
Displays a DVD disc menu which varies with the
disc and may be the same as the 'Title menu.'
K
L
s
B
/ / / buttons:
Selects the current highlighted menu option.
Number buttons:
Moves the cursor on the screen.
ENTER button:
Selects a numbered menu option (only for some
discs). ENTER button should be pressed after
pressing Number buttons.
Selects the currently highlighted menu option.
Number buttons:
Selects a numbered menu option (only for some
discs). ENTER button should be pressed after
pressing Number buttons.
3 Press TOP MENU button to exit the title menu.
3 Press DISC MENU button to exit the menu.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
PLAYING
Fast Forward / Fast Reverse
Special Playback
DVD-V DVD-R DVD-RW (Video)
Resume
DVD-RW (VR)
CD
MP3
DVD-V DVD-R DVD-RW (Video)
DVD-RW (VR)
CD
MP3
PLAY B (DVD)
E D
You can resume play from where you stopped play-
ing the disc last.
NOTE:
1 During playback, press D or E button.
• For MP3 files, playback will resume from the beginning of the
track at which playback was stopped.
Every time you press D or E button, approxi-
mate speed changes as follows.
Normal
speed
PLAY B (DVD)
STOP C (DVD)
x40
x20
x5
x2
x20
x40
playback
For Audio CDs, approximate speed is set at x8
with sound.
1 During playback, press STOP C (DVD) button.
The resume message will appear.
For MP3 files, approximate speed is set at x16.
To return to the normal playback, press PLAY
B
DISC Resume ON
(DVD) button.
NOTE:
2 Press PLAY B (DVD) button.
• For DVD discs, the sound will be output during playback in
fast forward of x2 only if you set "Fast Forward with Audio" to
"ON" for the "Playback" setting in the SETUP menu.
In a few seconds, playback will resume from the
point at which it stopped last.You can resume
play at the same point even if you turn off the unit.
• Forward/reverse speed will be indicated with icons as follows.
Forward (Approx. Speed)
Reverse (Approx. Speed)
x2 :
x20:
x40:
x5 :
x20:
x40:
To cancel the resume play and start playing the
disc from the beginning, press STOP C (DVD)
button again while the playback is stopped.
Slow Forward / Slow Reverse
Pause
DVD-V DVD-R DVD-RW (Video) DVD-RW (VR)
DVD-V DVD-R DVD-RW (Video)
DVD-RW (VR)
CD
MP3
PLAY B (DVD)
E D
PAUSE
F
PLAY B (DVD)
PAUSE
F
1 During playback, press PAUSE F button, then
press D or E button.
Every time you press D or E button, approxi-
mate speed will be changed as follows.
1 During playback, press PAUSE F button.
Playback will pause and sound will be muted.
Pause
x1/4
x1/8
x1/16
x1/16
x1/8
x1/2
To return to the normal playback, press PLAY
B
(DVD) button.
DISC
NOTE:
• The sound will remain mute.
2 Press PLAY B (DVD) button to resume play.
• Forward/reverse speed will be indicated with icons as fol-
lows.
Forward (Approx. Speed)
Reverse (Approx. Speed)
x1/16:
x1/8 :
x1/2 :
x1/16:
x1/8 :
x1/4 :
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Step by Step
Zoom
DVD-V DVD-R DVD-RW (Video) DVD-RW (VR)
DVD-V DVD-R DVD-RW (Video) DVD-RW (VR)
DISPLAY
K
L
CHANNEL
/
/
/
/
PLAY B (DVD)
ENTER
PAUSE
F
1 During playback, press PAUSE F button.
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
Playback will pause and sound will be muted.
DVD-Video
1
1
1:23:45
s
B
2 Select
ENTER button.
Zoom option menu will appear.
icon using
/
buttons, then press
DISC
K
2 Press CHANNEL button repeatedly.
DVD-Video
1
1
01:23:45
Every time you press the button, the playback
will go forward by one frame (or step) with the
sound muted.
x1.2
x1.5
x2.0
Three options (x1.2, x1.5, x2.0) excluding the
current zoom rate are displayed.
L
Press CHANNEL button repeatedly.
Every time you press the button, the playback
will go backward by one frame.
s
B
3 Select a desired zoom factor to zoom using
/
buttons, then press ENTER button.
The zoom area will be displayed.
3 Press PLAY B (DVD) button to resume play.
K
L
s
B
4 Select a desired zoom position using / / /
buttons, then press ENTER button.
The zoom play will start.
NOTE: Zoom
• When selecting a smaller factor than the current one, the
zoom area will not be displayed.
•
To remove the zoom menu, press DISPLAY button again at step [1].
• To cancel the zoom function, select x1.0 using s / B but-
tons, then press ENTER button.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
PLAYING
Setting Marker
Search
DVD-V DVD-R DVD-RW (Video)
DVD-V DVD-R DVD-RW (Video) DVD-RW (VR)
Title/Chapter Search
DVD-RW (VR)
CD
This feature allows you to assign a specific point on
a disc to be returned to later.
DISPLAY
K
L
CHANNEL
/
DISPLAY
Number
/
/
/
CLEAR
/
ENTER
ENTER
KL
Using CHANNEL
buttons
K
1 During playback, press CHANNEL button to
1 During playback, press DISPLAY button repeated-
skip the current title or chapter and move to the
next.
ly until the DVD status display menu appears.
DVD-Video
The title or chapter will move forward by one title
at a time.
1
1
1:23:45
To go back to the previous title or chapter, press
L
CHANNEL button. The title or chapter will
s
B
2 Select
ENTER button.
Marker setup menu will appear.
Screen for DVD: Screen for CD:
icon using
/
buttons, then press
move backward by one title at a time.
L
Only press CHANNEL button once to go back
to the top of the current title.
DVD-Video
Audio CD
1
1
01:23:45
1
01:23:45
Using DISPLAY button
1
2
3
4
5
6
1
2
3
4
5
6
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
s
B
3 Select a desired marker number using
/
but-
DVD-Video
1
1
1:23:45
tons.
When it reaches the desired point, press ENTER
button.
s
B
2 Select
icon using
ENTER button.
/
buttons, then press
4 To return to the marker later, select the desired
s
B
marker number using
/
buttons, then press
'T' for title will be highlighted.
ENTER button.
Title:
NOTE: Marker
K L
/
Enter a desired title number to search using
• You can mark up to 6 points.
• To clear a marker, select the marker number to be cleared,
then press CLEAR button.
• All markers will be erased by the following operation:
Opening the disc tray
Turning off the power
Recording to a recordable disc
Changing the mode between Original and Playlist
(VR mode)
buttons or Number buttons, then press ENTER
button. Title search will start.
Chapter:
To move to 'C' for chapter, press B button.
Enter a desired chapter number to search using
K L
/
buttons or Number buttons, then press
Editing the disc
ENTER button.
Chapter search will start.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Track Search
Time Search
CD
MP3
DVD-V DVD-R DVD-RW (Video)
DVD-RW (VR)
CD
DISPLAY
Number
DISPLAY
Number
K
L
CHANNEL
/
/
/
/
/
/
/
ENTER
ENTER
KL
Using CHANNEL
buttons
K
1 During playback, press CHANNEL button to
1 During playback, press DISPLAY button repeated-
skip the current track and move to the next.
ly until the DVD status display menu appears.
The track will move forward one at a time.
Screen for DVD:
To go back to the previous track, press CHAN-
NEL button. The track will move backward one
DVD-Video
1
1
1:23:45
L
track at a time.
Screen for CD:
Using DISPLAY button
Audio CD
1
01:23:45
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
Audio CD
1
01:23:45
s
B
2 Select
ENTER button.
'T' for title or track will be highlighted.
icon using
/
buttons, then press
s
B
2 Select
icon using
ENTER button.
/
buttons, then press
B
(clock) icon, press button.
To move to the
'T' for track will be highlighted.
K
L
3 Enter a desired time to search using
/
but-
tons or Number buttons, then press ENTER but-
3 Enter a desired track number to search using
ton.
K L
/
buttons or Number buttons, then press
Time search will start.
ENTER button.
NOTE:
Track search will start.
• Time search function is available only in the same track or
title.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
PLAYING
Repeat/Random/Program Play
Track: CD, MP3 only
The current track will be played repeatedly.
Group: MP3 only
Repeat Play
DVD-V DVD-R DVD-RW (Video)
The current group will be played repeatedly.
DVD-RW (VR)
CD
MP3
NOTE:
• You cannot select "Group" during the random playback of
MP3 files.
DISPLAY
Random Play
CD
MP3
You can play tracks on a disc randomly instead of
playing it in the recorded sequence.
/
/
/
ENTER
SETUP
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
/
/
/
DVD-Video
1
1
1:23:45
ENTER
STOP C (DVD)
s
B
2 Select
ENTER button.
Repeat menu will appear.
icon using
/
buttons, then press
1 In the stop mode, press SETUP button to display
SETUP/CD menu.
DVD-Video
1
1
01:23:45
SETUP/CD menu will appear.
OFF
Title
Chapter
A-B
s
B
2 Select "CD" using
/
buttons, then press
ENTER button.
NOTE:
• To cancel the repeat playback, select OFF.
CD Playback Mode menu will appear.
K L
/
3 Select a desired option to repeat using
but-
K L
/
3 Select "Random Play" using
buttons, then
tons, then press ENTER button.
press ENTER button.
Title: DVD only
Random playback will start.
The current title will be played repeatedly.
NOTE:
• To cancel random playback, press STOP C (DVD) button
Chapter: DVD only
during random playback.
The current chapter will be played repeatedly.
All: CD, MP3 and DVD-RW (VR mode only)
The current disc will be played repeatedly.
A-B:
The A-B point will be played repeatedly.
When pressing ENTER button while A-B is high-
lighted, the starting point (A) will be decided.
Press ENTER button again to select the ending
point (B).
NOTE:
• The A-B Repeat playback can only be set within the current
title (for DVDs) or current track (for Audio CDs).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Play
Selecting AUDIO / VIDEO Menu
CD
You can select an audio or video format, as you pre-
fer depending on the contents of the disc you are
playing.
You can program tracks on a disc to be played in
your desired order.
Switching Audio Soundtrack
NOTE:
• You can make program up to 50 tracks.
DVD-V DVD-RW (VR)
When playing a DVD-Video disc recorded with two
or more soundtracks (mostly in different languages),
you can switch between them anytime during play-
back.
Number
SETUP
CLEAR
NOTE:
• Some discs will only allow you to change the soundtrack
from the disc's menu. Press TOP MENU button or DISC
MENU button to display the disc's menu.
/
/
/
ENTER
PLAY B (DVD)
• On DVD-RW discs recorded in VR mode that may have both
a main and a sub audio channel, you can switch to main (L),
sub audio (R) or a mix of both (L/R).
STOP C (DVD)
1 In the stop mode, press SETUP button to display
DISPLAY
SETUP/CD menu.
SETUP/CD menu will appear.
s
B
2 Select "CD" using
/
buttons, then press
ENTER button.
CD Playback Mode menu will appear.
/
/
/
K L
/
3 Select "Program Play" using
buttons, then
ENTER
press ENTER button.
Program Play list will appear.
1 During playback, press DISPLAY button repeated-
CD Playback Mode > Program Play
ly until the DVD status display menu appears.
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
DVD-Video
1
1
1:23:45
Total
00:00:00
s
B
2 Select
icon using
ENTER button.
/
buttons, then press
4 Select a desired track using K/L buttons, then
B
press ENTER button or button.
Audio menu will appear.
<DVD-Video>
A cursor will move to the next.
CD Playback Mode > Program Play
DVD-Video
1
1
1:23:45
07 - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - -
1
2
Dolby Digital 5.1ch English
Dolby Digital 2ch Japanese
Total
00:04:30
<DVD-RW VR mode>
DVD-RW
VR Original
1
1
1:23:45
NOTE:
1
2
Dolby Digital Dual L/R
Dolby Digital 2ch ----
• You may also select a desired track using Number buttons.
• To erase tracks you selected, press CLEAR button.
5
Press PLAY B (DVD) button to start program playback.
Program playback will start according to your program.
NOTE:
Continue on next page.
• To cancel program playback, press STOP C (DVD) button
twice during program playback.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
PLAYING
K
L
CD
MP3
3 Select a desired audio soundtrack using
/
buttons, then press ENTER button.
When playing Audio CDs or MP3 files you can
switch between stereo, the left channel only or the
right channel only.
<DVD-Video>
Audio soundtrack will switch.
<DVD-RW VR mode>
DISPLAY
You can switch to main (L), sub audio (R) or a
mix of both (L/R). In this case, follow the step [4].
DVD-RW
VR Original
1
1
1:23:45
1
2
Dolby Digital Dual
Dolby Digital 2ch
L/R
L
R
/
/
/
K L
/
4 Select a desired audio channel using
but-
tons, then press ENTER button.
ENTER
Audio channel will switch.
NOTE:
1 During playback, press DISPLAY button repeated-
• This unit CANNOT record in both stereo and SAP
(Secondary Audio Program) at the same time.
ly until the DVD status display menu appears.
Audio CD
1
1:23:45
s
B
2 Select
icon using
ENTER button.
Audio menu will appear.
/
buttons, then press
K L
/
3 Select a desired audio channel using
but-
tons, then press ENTER button.
Audio channel will change.
Audio CD
1
1:23:45
L/R
L
R
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching Subtitles
Switching Camera Angles
DISPLAY
DVD-V DVD-RW (VR)
DVD-V
Many DVD Video discs have subtitles in one or
more languages. The case usually tells you which
subtitle languages are available. You can switch sub-
title languages anytime during playback.
NOTE:Top Menu / Disc Menu
• Some discs allow you to change the subtitle only from the
disc's menu. Press TOP MENU button or DISC MENU but-
ton to display the disc's menu.
/
DISPLAY
ENTER
Some DVD Video discs feature scenes shot
from two or more angles, check the case of
the DVD for details:
it should be marked with an angle icon if it
contains multi-angle scenes.
DISC MENU
/
/
/
ENTER
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
DVD-Video
1
1
01:23:45
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
DVD-Video
1
1
1:23:45
DISC
Angle icon appears when a switching camera
angle is available.
s
B
2 Select
ENTER button.
Subtitle menu will appear.
icon using
/
buttons, then press
s
B
2 Select
icon using
/
buttons, then press
ENTER button.
DVD-Video
1
1
1:23:45
Angle will switch each time you press ENTER
button.
OFF
1English
2Japanese
K L
/
3 Select a desired subtitle language using
buttons, then press ENTER button.
Subtitle will be displayed in the selected lan-
guage.
When selecting "OFF", subtitle will disappear.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
PLAYING
Reducing Block Noise
Virtual Surround Setting
DVD-V DVD-R DVD-RW (Video) DVD-RW (VR)
DVD-V DVD-R DVD-RW (Video) DVD-RW (VR)
This function reduces noise in the playback picture.
Switching to virtual surround setting allows you to
enjoy DVD disc with a surround effect.
DISPLAY
DISPLAY
/
/
/
/
/
/
ENTER
ENTER
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
1 During playback, press DISPLAY button repeated-
ly until the DVD status display menu appears.
DVD-Video
1
1
1:23:45
DVD-Video
1
1
1:23:45
s
B
2 Select
icon using
ENTER button.
NR menu will appear.
/
buttons, then press
s
B
2 Select
icon using
ENTER button.
Virtual surround menu will appear.
/
buttons, then press
DVD-Video
1
1
1:23:45
DVD-Video
1
1
01:23:45
OFF
Type 1
Type 2
ON
OFF
K L
/
3 Select a desired option using
buttons, then
K L
/
press ENTER button.
3 Select "ON" using
buttons, then press
ENTER button.
Your setting will be activated.
Virtual surround setting will be activated.
When playing back discs recorded in long time
mode such as SLP or SEP mode, select "Type
1" or "Type 2". ("Type 2" is more effective.) When
playing back prerecorded DVD discs with little or
no noise, select "OFF".
NOTE:
• To turn off virtual surround, select "OFF" in Virtual Surround
menu screen.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
UIDE TO DISPLAYS ON SCREEN MENU
G
This unit uses the following types of display for most operations. SETUP/DISC/CD menu, Title List, and DIS-
PLAY, which allows you to change the playing status of disc during play.
SETUP/DISC/CD menu
Press SETUP button to display the setup main menu, then choose either of SETUP/DISC/CD by pressing s /B
buttons.Then, press ENTER button to display each menu. This provides entries to all main functions of the unit.
"SETUP" is available only
in the Stop mode.
"CD" is available only
when an Audio CD disc or
a CD-R/RW disc with MP3
files is inserted into the
unit.
"DISC" can be only selected when a
DVD-R/RW disc is inserted into the unit.
When a prerecorded DVD Video disc, a
new DVD-R disc or the finalized DVD-R
disc is inserted into the unit, you cannot
select "DISC".
Setup Menu
Setup
Disc Setting
CD Playback Mode
CD Playback Mode
Disc
Edit
Random Play
Program Play
Format
Finalize
1
2
5
3
6
Disc Protect OFF ON
1 2 3 4
1 2
4
Playback Setting
1. Playback:
1. Edit:
1. Random Play:
To set up the unit to play discs to
your preference.
2. Recording:
To set up the unit to record to
Turns on a title list, (when a disc
with VR mode is inserted,
'Original' or 'PlayList' is available),
which shows the recorded titles
on the disc.
To set the random CD tracks play-
back.
2. Program Play (Audio CD
only):
To activate the programmed play-
discs or VHS tape.
3. Display:
2. Format:
back of CD tracks.
To set up the OSD screen.
Allows you to erase all of the
4. Select Video:
recorded content on the disc. The
To choose a line input to record to DVD disc will be completely blank.
discs or VHS tapes from other video
components.
3. Finalize:
Allows you to finalize a disc
5. Clock:
recorded titles.
To set up the clock.
6. Channel:
To preset the TV channels.
4. Disc Protect (VR mode only) :
Allows you to protect a disc from
accidental editing or recording.
You will need to finalize the DVD discs before they can be played in other DVD players.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
ASY DVD RECORDING
E
The following will help you to understand easily how to record to DVD discs.
NOTE:
• Make sure that you have completed connections and batteries should be inserted in the remote control.
Step 1: Choose a disc
type
Step 3: Select the
Recording
speed
Step 2: Insert a
blank
disc
There are several types of DVD disc
recordable to choose from. Choose an
applicable type by "DVD disc types" on
this page.
This unit can record on the following
type of discs only.
Turn on the unit
1
2
3
To select the recording
speed, press REC
SPEED button once,
then change the record-
Open the disc tray
Close the disc tray
K L
/
ing speed using
buttons.
Remote Control
1
(or)
2
* This unit cannot record on the follow-
ing discs.
• DVD-R General Ver 2.0 / 8x
• DVD-RW Ver 1.2 / 2-4x CPRM com-
patible
For example, when you want to
record repeatedly on the same disc
or when you want to edit the disc
after recording, select the rewritable
DVD-RW type disc.
SP 1:01 Rem.
3
Loading
When you want to save recordings
without any alteration, a non-
rewritable DVD-R can be your choice.
NOTE:
• This operation may take a
few minutes to complete.
DVD disc types
Important
.
: Most suitable.
You want to
Record TV programs
: Can be used.
: Some functions are limited.
: Cannot be used.
Format the disc
DVD-RW VR
DVD-RW Video
DVD-R
Insert the disc in the unit,
then format the disc from
SETUP menu. Video format
(Video mode) or Video
Reuse by deleting unwanted contents
Edit recorded contents
Edit/Record from connected equipment
Copy discs for distribution
*1
*1
recording format (VR mode)
will be available depending
on the disc type inserted.
This is necessary to prepare
the disc for recording. Details
are on pages 48-49.
* When you format, the
entire contents on that disc
will be erased.
Play on other DVD equipment
Features
Recording
Rewritable?
DVD-RW VR
DVD-RW Video
DVD-R
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
Can create chapters at fixed intervals (auto.)
Can create chapters wherever you like (manual)
Can record 16:9 size pictures
Yes
No
Yes
No
Can record Copy-Once programs
Editing
Can perform basic edit functions
Yes
Yes
Yes
No
Yes
No
Finalize the disc
After recording, you will need
to finalize the DVD discs
recorded in this unit before
they can be played in other
DVD players. See page 54.
Can perform advanced edit functions (Playlist edit)
*1
DVD-RW (VR mode) can only be played on
DVD equipment that is VR compatible.
NOTE:
For details of the above functions and implied
restrictions, see the explanations inside the manual.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Select the
desired
Step 5: Press DVD
RECORD
Step 6: Stop the
Recording
channel
button
58%
Writing to Disc
DISC
NOTE:
• This operation may take a few
minutes to complete.
CH 1
DISC
I
Playing the recorded contents
You can select the title you want to play from a displayed menu
and immediately start to play. Recorded contents are very accessi-
ble on a disc, the procedure is really simple as you choose a title
on a chapter from the menu screen.
Start Rec.
Title 1
Stop/Start
Stop Rec.
Title 2
What are titles and chapters?
The contents of DVD disc are generally divided into titles. Titles
may be further subdivided into chapters.
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
Editing the recorded disc
You will find editing discs very easy. This unit offers convenient edit functions, which are possible
only with DVD-R/RW discs.
You can edit the following from a Title list.
• Naming titles
• Setting pictures for thumbnails (VR mode)
• Setting/clearing chapter markers
• Deleting title part or scene (VR mode)
Title Delete : This deletes an entire scene permanently from the disc.
Scene Delete : This allows a user to edit within a specific scene (ex. commercials).
Original and Playlist (VR mode)
You can edit the recordings in Playlist without changing the original recordings. Any Playlist
does not take up much disc space.
What "Original" or "Playlist" is for?
Throughout this manual, you will find Original and Playlist to refer to the actual content and the
edited version.
• Original content refers to what's actually recorded on the disc.
• Playlist content refers to the edited version of the disc; how the Original content is to be played.
Finalize the Disc
• This will allow a disc that is recorded on our unit to be played back on a different DVD player
without finalization it will not be playable on another player.
• After finalizing a disc if the recording was in video mode, you can not edit any information that
is on that disc.
• If you have recorded in VR mode on DVD-RW disc then editing is still permitted after finalizing.
See page 54.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
ECORDING
R
About DVD Recording
Disc type Disc format Functions
Video mode
This unit can record to DVD-R and DVD-RW discs. When
recording, you will need to select a recording format between
Video mode and VR mode depending on the disc format.The
disc format for DVD-R is always "Video format," so a recording
format will be "Video mode". On the other hand, when record-
ing to DVD-RW, a recording format will be "Video mode" or
"VR mode" because a disc format is available between "Video
Recording format" and "Video format" for DVD-RW.
Playing, limited recording,
limited editing
DVD-RW (Video)
VR mode
DVD-RW DVD-RW (VR)
Playing, recording,
Original/Playlist editing
Video mode
DVD-R
Playing, limited recording,
limited editing
DVD-R
Logo
Attributes
12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
600 minutes (4.7GB)
Recording Speed
You can select a recording speed among 6 options.
The recording time depends on the recording speed
you select as follows:
DVD-RW
12cm, single-sided, single layer disc
Approx. max. recording time (SEP mode):
600 minutes (4.7GB)
Recording Recording
Video/Sound Quality
speed
time *
DVD-R
(Highest)
XP (1H)
60 min
* This unit cannot record on the following discs.
•DVD-R General ver 2.0/8x
•DVD-RW ver 1.2/2-4xCPRM compatible.
SP (2H)
LP (4H)
EP (6H)
120 min
240 min
360 min
Important
Video mode / VR (Video Recording) mode
SLP (8H) 480 min
Video Format
Select the Video Recording Mode to record discs that can
played back on most standard DVD players. Video Recording
Mode creates discs compatible with most DVD players, but
there is no capability to edit the recordings. DVD-R discs can
only be formatted in the Video mode, DVD-RW discs can be
formatted in the Video mode or the VR mode.
(Lowest)
SEP (10H) 600 min
* This table is designed for a new single-sided 12cm
disc as the standard. The recording time shown
above may differ from actual recording time.
VR Format
* The audio and video quality is poorer as the
recording time becomes longer.
Select the VR Recording Mode to record discs that can
be edited, but can be played back only on DVD recorders
and players that support the VR mode with DVD-RW
discs. DVD-R discs cannot be formatted in the VR mode,
only DVD-RW discs can be formatted in the VR mode.
* Discs recorded in SLP or SEP on this recorder
may not be playedback on other DVD recorders or
DVD players.
DVD players with
can play DVD-RW
recorded in VR mode.
NOTE:
• This unit cannot record CD-R or CD-RW discs.
•
DVD-R/RW and CD-R/RW discs recorded on a personal computer or
a DVD or CD recorder may not be played in this unit if the disc is dam-
aged or dirty or if there is dirt of condensation on the units lens.
• Even if you record a disc using a personal computer in a
compatible format, you may not play it in this unit due to the
application software used to create the disc. (Check with the
software distributor for more detailed information.)
• Discs recorded in Video mode on this unit cannot be record-
ed additionally using other DVD recorders.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Restrictions
Formatting
You cannot record copy-protected video using this
unit. Copy-protected video includes DVD-Video
discs and some satellite broadcasts. If copy-protect-
ed material is encountered during a recording, the
unit will pause or stop automatically and an error
message will be displayed on-screen. "Copy-once
only" video can be recorded only using a DVD-RW
disc in VR mode with CPRM (see below). When
recording a TV broadcast or through an external
input, copy control information can be displayed on
screen.
Format Setting
DVD-RW (Video) DVD-RW (VR)
When inserting a blank disc, the unit starts to initialize
the blank disc. After that, you can record to the disc in
the recording format selected in SETUP menu. You
can set a specified time for chapter marks.
NOTE:
• The recording format setting is available only for DVD-RW
discs. You cannot change the recording format on a DVD-R
disc. DVD-R discs will always be in Video mode.
• You cannot mix two formats on one DVD-RW disc. When you
load a disc once recorded before, the recording format can-
not be changed even if you change it in SETUP menu.
What is "CPRM"?
CPRM is a copy protection system with scramble
system regarding the recording of "copy once"
broadcast programs. CPRM stands for Content
Protection for Recordable Media. This unit is
CPRM compatible, which means that you can
record copy-once broadcast programs, but you
cannot make a copy of those recordings. CPRM
recordings can only be made on DVD-RW discs
formatted in VR mode, and CPRM recordings can
only be played on players that are specifically
compatible with CPRM.
• When inserting a blank DVD+R or DVD+RW disc, the error
message ("Disc Error") will appear. This unit is not compati-
ble with a DVD+R/RW disc.
• PLAYLIST will be created automatically when recording on
DVD-RW in VR mode.
SETUP
/
/
/
ENTER
Copy Control
Some satellite broadcasts include copy-protected
contents. Refer to the following condition on copy
control.
Copy-
prohibited
1 Press SETUP button to display SETUP/DISC
Disc type / format
Copy-free Copy-once
menu.
ver.1.1
VR
DVD-RW
SETUP/DISC menu will appear.
ver.1.1 CPRM compatible
s
B
ver.1.1
2 Select "SETUP" using
/
buttons, then press
Video
DVD-RW
ENTER button.
ver.1.1 CPRM compatible
SETUP menu will appear.
ver.2.0
DVD-R
K
L
s
B
3 Select "Recording" using / / / buttons, then
Recordable
Not Recordable
press ENTER button.
Recording menu will appear.
K L
/
4 Select "DVD-RW Recording Format" using
buttons, then press ENTER button.
Option window will appear.
Setup > Recording
DVD
Video mode
DVD-RW Recording Form
Auto Chapter
VR mode
Timer Programming
Video mode
DVD Player Compatibility mode.
VR mode
Editing possibility mode.
Video mode has been selected as the default.
Continue on next page.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
RECORDING
Reformatting
K L
/
5 Select "Video mode" or "VR mode" using
buttons, then press ENTER button.
DVD-RW (Video) DVD-RW (VR)
The recording mode will be set.
If you are using a DVD-RW disc, by default it will be
Video mode.
K L
/
6 Select "Auto Chapter" using
buttons, then
You can change this to VR mode from SETUP
menu.
press ENTER button.
Option window will appear.
Caution: Erasing - Reformatting
• Reformatting will erase the contents of the disc. Once
erased, the material cannot be retrieved.
Setup > Recording
DVD
DVD-RW Recording Forma
Auto Chapter
OFF
5 minutes
10 minutes
15 minutes
30 minutes
Timer Programming
60 minutes
SETUP
"10 minutes" has been selected as the default.
/
/
/
K L
/
7 Select a desired time option using
buttons,
ENTER
then press ENTER button.
Chapter marks will be put as you specified.
• The time for chapter marks is not accurate in
Video mode.
1 Press SETUP button to display SETUP/DISC
8 Press SETUP button to exit SETUP menu.
menu.
NOTE: 2 formats on same disc
SETUP/DISC menu will appear.
You cannot mix both recording formats on a single DVD disc.
NOTE: Finalize
s
B
2 Select "DISC" using
/
buttons, then press
You must "Finalize" all recorded discs before they can be
played on other DVD players. Without finalization, Video mode
discs cannot be played back on other DVD players, and VR
mode discs cannot be played back on other VR compatible
players. See page 54.
ENTER button.
DISC menu will appear.
K
L
/
3 Select "Format" using
buttons, then press
ENTER button.
Option window will appear.
* VR mode only
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Yes
No
s
B
4 Select "Yes" using
/
buttons, then press
ENTER button.
Option window will appear.
* VR mode only
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Yes
Are you sure?
Yes No
No
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Recording
s
B
5 Select "Yes" using
/
buttons, then press
ENTER button.
Recording TV Programs
Formatting will start.
DVD-R DVD-RW (Video) DVD-RW (VR)
Follow the steps below to record TV programs.
NOTE:
• Select "No" to cancel formatting.
K
L
CHANNEL
Number
/
58%
Formatting
/
6 Formatting is complete.
REC SPEED
100% will be indicated.
DVD RECORD
PAUSE
STOP C (DVD)
F
1 Turn on the unit and load a recordable disc.
NOTE:
100%
Formatting
• This operation may take a few minutes to complete.
NOTE:
2 Press REC SPEED button, then change the
• This operation may take a few minutes to complete.
K L
/
recording speed using
buttons.
SP 1:01 Rem.
Refer to "Recording speed" on page 48.
3 Make sure that the recording format is set to the
desired mode.
Refer to "Formatting" on pages 49-50.
When a DVD-RW disc is loaded:
Choose Video mode or VR mode from SETUP
menu. "Video mode" has been selected as the
default. Refer to "Format Setting" on pages 49-
50.
When a DVD-R disc is loaded:
DVD-R discs will always be in Video mode.
NOTES:
• If the clock has not been set, the space for a date
and time of title names in the original or playlist
will be blank.
• You cannot mix two formats on one DVD-RW
disc. When you load a disc once recorded before,
the recording format cannot be changed even if
you change it in SETUP menu.
Continue on next page.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
RECORDING
Checking the recording picture quality
4 Select a desired channel to record using CHAN-
K L
/
NEL
buttons or Number buttons.
DVD-R DVD-RW (Video) DVD-RW (VR)
You can confirm the recording speed you have
selected before recording to a DVD disc.
CH 1
5 Press DVD RECORD button to start recording.
/
NOTE:
REC
MONITOR
• Recording starts immediately and continues until the disc is
full or you stop recording.
REC SPEED
DISC
I mark will be displayed for 5 seconds.
1 While the unit is in STOP or REC with a record-
able DVD disc inserted, press REC MONITOR
button.
DISC
I
2 The TV program will be shown on the screen
with the recording speed you have selected.
Please confirm this is the speed you wish to
record.
To pause the recording, press PAUSE F button.
Press DVD RECORD button to restart the
recording.
NOTE:
NOTE:
• The recording picture can be confirmed with the Rec moni-
tor function. (See "Recording Speed" on page 48.)
• You cannot change the recording speed during the REC
pause mode.
• You can change a channel during the REC pause mode.
XP 0:30 Rem
CH 18
6 Press STOP C (DVD) button to stop recording.
NOTE:
• This operation may take a few minutes to complete.
Rec Monitor
XP
3 To change the recording speed, press REC
K L
/
SPEED button, then use
buttons.
The recording speed will change as you press
the button as shown.
XP
SP
LP
SEP
SLP
EP
DVD mode
NOTE:
• You cannot change the recording speed during recording.
4 Press REC MONITOR button again to exit.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
One-Touch Timer Recording
DVD-R DVD-RW (Video) DVD-RW (VR)
This is a simple way to set the recording time in
blocks of 30 minutes. Check that the disc you are
recording onto has enough space for the time you
set.
0:30
DISC
I
0:30
OFF (Normal Recording) 1:00
Remote control
K
L
CHANNEL
/
Number
8:00
7:30
When the unit reaches the specified time, it will
turn off automatically.
/
NOTE: Automatic Turn Off
• The unit will turn off automatically under the following condi-
tions:
REC SPEED
Main Unit
1) No space remained on the disc.
2) When a power failure occurs.
STOP C (DVD)
• If One-Touch Timer Recording finishes in DVD during play-
back or in REC mode in VCR, the DVD will be in STOP
mode and the VCR keeps the current mode.
To cancel the one-touch timer recording within
the specified time, press STOP C (DVD) button.
C STOP
(DVD)
I RECORD
(DVD)
NOTE:
• This operation may take a few minutes to complete.
1 Turn on the unit and load a recordable disc.
Important
NOTE:
You must "Finalize" all recorded discs before
they can be played on other DVD players.
Without finalization, Video mode discs cannot be
played back on other DVD players and VR mode
discs cannot be played back on other VR com-
patible players. See page 54.
• This operation may take a few minutes to complete.
2 Press REC SPEED button, then change the
K L
/
recording speed using
buttons.
Refer to "Recording speed" on page 48.
3 Make sure that the recording format is set to the
desired mode.
Refer to " Format Setting " on pages 49-50.
When a DVD-RW rewritable disc is loaded:
Choose Video mode or VR mode from SETUP
menu.
"Video mode" has been selected as the default.
Refer to " Format Setting" on pages 49-50.
When a DVD-R disc is loaded:
DVD-R discs will always be in Video mode.
4 Select a desired channel to record using CHAN-
K L
/
NEL
buttons or Number buttons.
5 Press I RECORD (DVD) button on the main
unit repeatedly until a desired recording time (30
minutes to 8 hours) appears on the TV screen.
Recording will start.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
RECORDING
You cannot cancel finalizing the DVD-R disc once it
starts.
Finalizing Discs
DVD-R DVD-RW (Video) DVD-RW (VR)
SETUP
You must "Finalize" all recorded discs before they
can be played on other DVD players. Without final-
ization, Video mode discs cannot be played back on
other DVD players, and VR mode discs cannot be
played back on other VR compatible players.
/
/
/
ENTER
STOP C (DVD)
1
Press SETUP button to display SETUP/DISC menu.
Finalizing*
SETUP/DISC menu will appear.
s
B
2 Select "DISC" using
/
buttons, then press
ENTER button.
Playable
DISC menu will appear.
DVD player
K L
/
3 Select "Finalize" using
buttons, then press
Not Playable
ENTER button.
This Unit
Option window will appear.
Disc
Edit
*You cannot finalize discs in other DVD recorders.
Format
Finalize
Disc Protect OFF ON
Yes
No
Finalizing may take several minutes up to an hour.
(A disc recorded in Video mode can take up to 15
minutes. A disc recorded in VR mode can take up to
60 minutes.)
* VR mode only
A shorter recording period on the disc will require a
longer time period for finalization. Do not unplug the
power cord during finalization.
s
B
4 Select "Yes" using
/
buttons, then press
ENTER button.
Finalizing will start.
After finalizing:
• Once DVD-R/RW (Video mode) is finalized, you
cannot record additionally or edit.
• Even if DVD-RW (VR mode) is finalized, you can
record additionally to or edit.
58%
Finalizing
• When DVD-R/RW (Video mode) is finalized, title
menu will be created automatically.
NOTE: Finalizing
• This operation may take a few minutes to complete.
•
Finalizing discs in Video mode automatically create title menus.
To play in other DVD players, finalize discs
recorded on this unit with the following condi-
tion.
• Once you have finalized a disc recorded in Video mode, you
cannot edit or record any contents on that disc.
Discs recorded in VR mode can still be recorded and edited
on this unit even after finalized.
• To cancel finalizing, press STOP C (DVD) button. Select
"Yes" using s/B buttons, then press ENTER button.
Disc type
Mode
DVD-R
ver.2.0
• When you insert a DVD-RW disc finalized with this unit,
"Undo Finalize" will appear instead of "Finalize".
Video mode
DVD-RW
Disc
ver.1.1
Video mode
VR mode
Edit
Format
ver.1.1 CPRM compatible
Undo Finalize
To release the finalizing for the disc, select "Undo Finalize"
at step [3].
• If
appear when pressing STOP C (DVD) button, you
cannot cancel finalizing because the finalizing has been in
certain progress.
When selecting "No", press ENTER or RETURN button,
finalizing will be continued.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CANCEL THE DISC PROTECT :
• When you insert a disc protected with this unit, “Disc Protect
Protecting Discs
ON ➔ OFF” will appear instead of “OFF ➔ ON”.
DVD-RW (VR)
Disc
To prevent accidental recording, editing or erasing
the titles, you can protect them.
Edit
Format
Finalize
Disc Protect ON OFF
Yes
No
SETUP
To release the protect for the disc, select “Disc Protect ON
➔ OFF” at step [3], then select “Yes”.
/
/
/
ENTER
1 Press SETUP button to display SETUP/DISC
menu.
SETUP/DISC menu will appear.
s
B
2 Select "DISC" using
/
buttons, then press
ENTER button.
DISC menu will appear.
K L
/
3 Select "Disc Protect OFF ➔ ON" using
but-
tons, then press ENTER button.
Option window will appear.
Disc
Edit
Format
Finalize
Disc Protect OFF ON
Yes
No
s
B
4 Select "Yes" using
/
buttons, then press
ENTER button.
A disc will be protected.
58%
Writing to Disc
NOTE:
• This operation may take a few minutes to complete.
• The Disc Protect setting is available only when a disc with
VR mode is inserted.
• You can only select Disc Protect Menu when a protected
disc is inserted.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
RECORDING
Recording from External Video Products
Connecting to External Video Products
Connections
DVD-R DVD-RW (Video) DVD-RW (VR)
VCR
Before recording from an external video product,
see the instructions for the connection in the previ-
ous section, “Connections”.
Connect the external video products properly to the
unit by using input jacks on the front of this unit.
Use S-Video or video cable and an audio cable for
this connection.
K
L
CHANNEL
/
OUTPUT
Other devices
S- VIDEO
VIDEO AUDIO
(ex.VCR camcorder etc.)
L
R
/
or
Video
cable
Audio
cable
DVD RECORD
REC SPEED
VCR RECORD
STOP C (DVD)
S-Video
cable
STOP C (VCR)
S-VIDEO
Recording
onto DVD
only
1 Turn the unit on.
2 When you want to record onto a DVD:
A
Press
OPEN/CLOSE button on the main unit
to open the disc tray, then place the disc to
To record onto a
VHS tape, use the
VIDEO input.
A
record properly, then press
OPEN/CLOSE
button again to close the disc tray.
NOTE:
• This operation may take a few minutes to complete.
1 Press SETUP button to display SETUP/DISC
When you want to record to a tape:
menu.
Insert the tape with a safety tab into the cassette
compartment.
s
B
2 Select "SETUP" using
/
buttons, then press
ENTER button.
3 Select the external input mode (“AUX” or “S”)
K L
/
using CHANNEL
buttons.
K
L
s
B
3 Select "Select Video" using / / / buttons,
then press ENTER button.
4 Press REC SPEED button (For VCR, press REC
SPEED button twice), then change the recording
Setup > Select Video
Line
DVD
AUX
K L
/
speed using
buttons until your desired speed
is displayed. Refer to "Recording Speed" on page
48 for DVD or page 28 for VCR.
XP
SP
LP
Press ENTER button.
Option window will appear.
SP
SLP
SEP
SLP
EP
DVD mode
VCR mode
K
L
4 Select the input jack type to connect using
/
buttons, then press ENTER button.
5 Press DVD RECORD button or VCR RECORD
If you want to use S-VIDEO INPUT, select "S".
button to start recording.
If you want to use VIDEO INPUT (Composite),
select "AUX".
6
Press PLAY button on the external video product.
7 For disc:
Setup > Select Video
Line
DVD
AUX
Press STOP C (DVD) button to stop recording.
S
NOTE:
• This operation may take a few minutes to complete.
For tape:
5 Press SETUP button to exit.
Press STOP C (VCR) button to stop recording.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
UBBING
D
DVD-R DVD-RW (Video) DVD-RW (VR)
VCR
You can copy a DVD disc to a videotape or copy a
videotape to a DVD disc. This function will be possi-
ble only if the DVD disc or the tape is not copy pro-
tected. Before starting this function, prepare for the
recording on the DVD-R/RW disc or the videotape.
Refer to pages 48-55, 28-30.
NOTE: Load Recording Media
• Insert a DVD disc or videotape with the available recording
space.
REC SPEED
STOP C (DVD)
STOP C (VCR)
VCR DVD
VCR DVD
VCR to DVD
DVD to VCR
The DVD recording speed and format should be
selected first. Refer to "Recording" on page 48 and
"Formatting" on pages 49-50.
The tape's record tab should be intact.
The videotape should have enough available space
to record the DVD disc.
1 Press REC SPEED button first, and select a
1 Press REC SPEED button twice and select a
K L
/
recording speed using
buttons.
K L
/
recording speed using
buttons.
2 Press VCR
DVD button on the remote control
or on the main unit.
2 Press VCR
DVD button on the remote control
or on the main unit.
VCR to DVD duplication will start.
DVD to VCR duplication will start.
3 Press STOP C (DVD) or STOP C (VCR) button
on the remote control or on the main unit to stop
the recording.
3 Press STOP C (DVD) or STOP C (VCR) button
on the remote control or on the main unit to stop
the recording.
NOTE:
NOTE: DVD Dubbing
• After starting VCR to DVD duplication, the picture may be
distorted because of the auto tracking function. This is not a
malfunction. Be advised to playback the tape until the pic-
ture is stabilized, then set the starting point you wish to start
recording, and start VCR to DVD duplication.
• Duplicating operation from DVD to VCR is only available
when DVD stops or during DVD playing, and when VCR
stops.
• You cannot make a dub from a DVD disc protected by copy-
right, such as a prerecorded DVD.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
IMER RECORDING
T
Timer Recording
6 Enter the date using K/L buttons, then press
B
DVD-R DVD-RW (Video) DVD-RW (VR)
VCR
button.
Setup > Recording > Timer Programming
You can program up to 7 programs 1 year in
advance. Daily or weekly program recordings are
also available.
JAN / 1/ 2004 (THU) 12 : 00 PM
DVD
Speed
VCR
Date
Start
End
CH
JAN / 01 - - : - -AM - - : - -AM CH8 DVD
- - -
- - -
e.g. January 1st
NOTE:Time must be set
• Be sure to set the clock before making a timer programming.
NOTE:
• Insert a recordable disc or a tape with a safety tab.
• When pressing L button at the current date, timer recording
mode will change as follows:
POWER
JAN/01
Daily
MON-SAT
MON-FRI
SAT
TIMER PROG.
SETUP
/
/
/
FRI
ENTER
SUN
DEC/31
1 Press SETUP button to display SETUP/DISC
menu.
K L
/
7 Enter the time to start and to end using
but-
SETUP/DISC menu will appear.
B
tons, then press button.
s
B
2 Select "SETUP" using
/
buttons, then press
Setup > Recording > Timer Programming
JAN / 1/ 2004 (THU) 12 : 00 PM
DVD
Speed
VCR
ENTER button.
Date
Start
End
CH
JAN/01 10 :00PM - - : - -AM CH8 DVD
- - -
SETUP menu will appear.
NOTE:
K
L
s
B
3 Select "Recording" using / / / buttons, then
• Press s or B buttons to move the cursor to the left and the
press ENTER button.
right in the timer programming menu.
Recording menu will appear.
K
L
/
8 Select the channel number to record using
K L
/
B
buttons, then press button.
4 Select "Timer Programming" using
buttons,
then press ENTER button.
Setup > Recording > Timer Programming
JAN / 1/ 2004 (THU) 12 : 00 PM
DVD
Speed
VCR
Timer Programming list will appear.
Date
Start
End
CH
JAN/01 10:00PM 10:30PM CH8 DVD
- - -
NOTE:Timer Program Menu
• Timer Programming menu can also be selected by pressing
• To record from external input, select “AUX”.
TIMER PROG. button. In this case, continue with step [5].
• If you have not set the clock yet:
A clock setting window will appear after step [4]. Before
making a timer programming, press ENTER button then fin-
ish setting the clock, referring to the step [5] in "Manual
Clock Setting" on page 19.
K
L
9 Select a recording media using
/
buttons,
B
then press button.
Setup > Recording > Timer Programming
JAN / 1/ 2004 (THU) 12 : 00 PM
DVD
Speed
VCR
Date
Start
End
CH
Setup > Recording > Timer Programming
JAN/01 10:00PM 10:30PM CH8 DVD
- - -
JAN / 1/ 2004 (THU) 12 : 00 PM
DVD
Speed
VCR
Date
- - -
- - -
Start
End
CH
• To record on to a tape, select VCR.
• To record on to a disc, select DVD.
K L
/
5 Select the blank program using
buttons,
then press ENTER button.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking, canceling, or correcting the timer pro-
gramming information
10 Select a recording speed using K/L buttons.
Setup > Recording > Timer Programming
JAN / 1/ 2004 (THU) 12 : 00 PM
DVD
Speed
VCR
Date
Start
End
CH
JAN/01 10:00PM 10:30PM CH8 DVD 1H
- - -
POWER
Refer to "Recording speed" on page 48 for DVD
or page 28 for VCR.
TIMER PROG.
CLEAR
• If you set Recording speed to “Auto” at step
[10], this unit will automatically adjust the
recording speed so that the program will fit into
one disc.
/
/
/
(You can select “Auto” in the first program only.)
ENTER
11 Press ENTER button when all information
1 Press POWER button.
required is entered.
Your program setting will be entered.
• To set another program, repeat steps [5] to [11].
• To exit, press SETUP button.
2 Press TIMER PROG. button. Timer Programming
list will appear.
Setup > Recording > Timer Programming
JAN / 1/ 2004 (THU) 12 : 00 PM
DVD
Speed
VCR
Date
Start
End
CH
JAN/01 10:00PM 10:30PM CH8 DVD 1H
- - -
12 Press POWER button to turn off.
Important
When you set the timer program in either DVD
mode or VCR mode, RECORD indicator (DVD)
will illuminate on the front of the TV. See item
No.19 on page 7.
3 Check the information.
4 To clear the timer programming, select your
K
L
desired program using
/
buttons, then press
CLEAR button.
NOTE:
• If power is not turned off and you continue watching TV,
“TIMER REC STANDBY” starts flashing on the TV screen 2
minutes before the programmed start time. In this case,
press POWER button to turn off to activate the timer record-
ing.
To correct the timer programming, select your
desired program using
ENTER button.
K
/
L
buttons, then press
Next, correct the timer programming using
• You may turn on the unit once the timer recording has start-
ed.
K
L
s
B
/ / / buttons.
Finally, press ENTER button again.
5 Press TIMER PROG. button to exit.
6 Press POWER button to return to the timer
standby mode.
NOTE:
• Press TIMER PROG. button to check the timer programming
in process.
When the timer recording is in process, that program will be
highlighted in red. In this case, you cannot select any other
program.
To stop the timer recording in process
Press POWER button first to turn on the unit. Then,
on the front panel of the unit, press STOP C (DVD)
button to stop the recording or C STOP/A EJECT
to stop the tape recording. STOP C button on the
remote control does not work for timer recording.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
TIMER RECORDING
Suggestions for Timer Recording
• If there is a power failure or this unit has been unplugged for more than 3 seconds, the clock setting and all timer settings will be lost.
• If a disc is not on the tray, timer recording cannot be performed. Please insert a recordable disc.
• If a tape with a record tab is not in the cassette compartment, timer recording cannot be performed. Please insert a recordable tape.
See "Accidental erasure prevention" on page 28.
• The main unit automatically ejects a tape without a record tab inserted in the compartment when you turn off the power and move to
timer standby mode.
• When all the timer recording is completed, the RECORD indicator disappears. To play the recorded disc (or the tape), press POWER
A
button first and then press PLAY B (DVD) or PLAY B (VCR). To eject the recorded disc (or the tape), press
OPEN/CLOSE (or
C
A
STOP/ EJECT) button.
• The timer recording is not performed in DVD and VCR at the same time. If you set two programs with the same channel and time both
in DVD and VCR, the program that has priority will be recorded.
• During timer recording or timer standby (RECORD indicator is on the front display), any operations on the unit will not be available. To
make these operations available, cancel the timer recording or timer standby first (RECORD indicator disappears).
• To cancel the timer standby mode, press POWER button.
• When the Start and the End time are the same, the length of the recording will be set for 24 hours. When the disc reaches at the end
during the recording, the unit turns itself off.
• When the programmed Start and End time are earlier than the current time, the recording will be set on the same date in the next year.
• If your programmed Start time for DVD recording is within 2 minutes from the current time, the power will turn on for recording standby
right after you turn the power off. For a videotape recording, the power will turn on shortly before the Start time.
• If a videotape ends during timer recording, the unit will stop, eject the videotape and turn itself off.
• When two or more programmings are overlapped, "Overlap" will be displayed.
The priority of overlapped settings
This unit records the programs according to priority if the timer programs are overlapped. The timer program set first is given priority.
A timer recording of lower priority will be canceled, begin from the middle or stopped at the end.
Check the overlapped timer programs and change the priority if necessary.
A programming set previously has priority
When some programming have been
made at the end time of the
programming currently being recorded:
A program set previously (PROG. B) has priority.
When the starting time is the same:
A program set previously (PROG.A) has priority.
ex.1
ex. 2
PROG.A
PROG. B
PROG.A
PROG. B
PROG. C
Actual
recording
Actual
recording
PROG.A
PROG. B
PROG.A
PROG. B
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to be recorded.
When the recording time is entirely overlapped:
PROG. A will not be recorded.
PROG.A
PROG.A
PROG. B
PROG. B
Actual
recording
Actual
recording
PROG. B
PROG.A
PROG. B
Note for DVD timer recording
Example:
• When the recording time
of two programs are over-
lapped or the End time of
a program and the Start
time of another is the
same, the first 20-90 sec-
onds of the subsequent
program will be cut off.
When the end time of the programming currently
being recorded and the starting time of the one to be recorded
sequentially are same:
PROG.A
PROG. B
Actual
PROG.A
PROG. B
recording
The first 20-90 seconds will be cut off.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
DITING DISCS
E
Editing in Video Mode
About Disc Editing
You can edit the following items for discs in Video
mode. Be sure that once you edit titles, they will not
remain as recorded originally.
Title List
Title list allows you to check the titles recorded on
the disc easily. You can choose a title to edit from
this screen and easily edit the titles as you prefer.
• Deleting titles (Refer to page 62)
• Putting names on titles (Refer to page 63)
•
Setting or clearing chapter markers (Refer to page 63)
Disc > Edit > Original
NOTE: Finalized Discs
1
12
3
• Once a disc is finalized, editing the disc or recording to the
disc will not be available. (Except DVD-RW discs in VR
mode.)
JAN/1 1:00AM
4
JAN/1 2:00AM
5
JAN/1 3:00AM
6
• A playlist is not available with the DVD-R discs and DVD-RW
discs in Video mode.
JAN/1 6:00AM
JAN/1 4:00AM
JAN/1 5:00AM
1
2
3
Editing in VR Mode
For discs in VR mode, you can edit from "Original"
menu or "Playlist" menu, which is created from the
original.
Disc > Edit > Original
Title Delete
Scene Delete
1
Editing original titles
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
The following operations can be used to edit the
original titles.
JAN/1 1:00AM CH12 XP
-Deleting titles (Refer to page 64)
0:01:25
-Deleting parts of titles (Refer to page 65)
-Putting names on titles (Refer to page 65)
-Setting or clearing chapter markers (Refer to page 66)
-Setting pictures for thumbnails (Refer to page 66)
-Setting titles to protect (Refer to page 67)
-Releasing titles from protecting (Refer to page 67)
Editing playlists
8 7
6
5
4
1. Titles recorded on the disc can be selected to
edit by pressing ENTER button with the cursor on
the title.
2. Protect icon, which appears when the title has
been protected.
3. The arrow icon, which means the title list includes
a next or a previous page. Press B or s button by
following direction of the icon.
You can create a playlist from original titles, so that
you can edit as you prefer without losing original
titles. The following operations you can edit with a
playlist.
4. The menus for editing titles as you prefer. The
available menu depends on the disc type and the
format type.
-Deleting titles (Refer to page 68)
-Deleting parts of titles (Refer to page 69)
-Putting names on titles (Refer to page 69)
-Setting or clearing chapter markers (Refer to page 70)
-Setting pictures for thumbnails (Refer to page 70)
-Adding titles to a playlist (Refer to page 71)
-Deleting a playlist (Refer to page 71)
5. The details of the title, which can be changed to
the title name you will edit.
6. Time status bar of the title.
7. The selected title thumbnails from the title list.
8. Playback status of the current disc.
NOTE: Original Titles
• Original titles once edited will not remain as recorded origi-
nally. When you want to leave the original as it is, edit the
playlist as you prefer. (Refer to pages 68-71.)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
EDITING DISCS
Editing Discs in Video Mode
K L
/
4 Select "Title Delete" using
buttons, then
press ENTER button.
Deleting Titles
Option window will appear.
DVD-R DVD-RW (Video)
Disc > Edit
Caution:
Title Delete
Edit Title Name
Chapter Mark
1
You can delete titles that you do not need anymore.
The titles once deleted cannot be recovered to the
disc. When the last title in the title list in Video mode
is deleted, the disc space to record will be
increased. For DVD-R disc, the disc space to record
will not be changed.
Yes
JAN/ 1 1:00AM CH12 XP
No
0:01:25
s
B
5 Select "Yes" using
/
buttons, then press
ENTER button.
Title will be deleted.
SETUP
NOTE:
• This operation may take a few minutes to complete.
/
/
/
6 After writing to disc is completed, press SETUP
ENTER
button to exit DISC menu.
s
B
1 Press SETUP button. Select "DISC" using
/
buttons, then press ENTER button.
DISC menu will appear.
Disc
Edit
Format
Finalize
K L
/
2 Select "Edit" using
buttons, then press
ENTER button.
Title list will appear.
Disc > Edit
1
2
3
JAN/1 1:00AM
4
JAN/1 2:00AM
5
JAN/1 3:00AM
JAN/1 4:00AM
JAN/1 5:00AM
K
L
s
B
3 Select a desired title using / / / buttons,
then press ENTER button.
Edit menu will appear.
Disc > Edit
Title Delete
1
Edit Title Name
Chapter Mark
JAN/ 1 1:00AM CH12 XP
0:01:25
• You cannot select “Chapter Mark” when a DVD-R
disc is inserted into this unit.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Naming Titles
Setting Chapter Markers
DVD-R DVD-RW (Video)
DVD-RW (Video)
You can name the titles and change the names from
this menu.
You can put chapter markers in each title. Once a
chapter is marked, you can use it for the chapter
search.You can set chapter markers at a specified
time you selected for titles with more than 5 minutes.
The title names will be displayed on a Title List.
SETUP
NOTE:
•
•
You cannot select a time for putting markers beyond a length of a title.
/
/
/
When recording at the recording speed other than XP or SEP, the
length of chapters may be slightly longer or shorter than the one spec-
ified at the step [2].
ENTER
•
A chapter marker may be delayed according to the recording content.
Follow the steps [1] to [3] on page 62 to display the
Edit menu.
SETUP
K L
/
1 Select "Edit Title Name" using
buttons, then
press ENTER button.
/
/
/
A window for entering a title name will appear.
ENTER
Disc > Edit > Edit Title Name
A B C
a b c
1 2 3
@ ! ?
1
Follow the steps [1] to [3] on page 62 to display the
Edit menu.
JAN/ 1 1:00AM CH12 XP
0:01:25
K L
/
1 Select "Chapter Mark" using
buttons, then
press ENTER button.
2 To enter a title name, follow the steps shown in
"Guide to edit title name" below.
Option window will appear.
Disc > Edit > Edit Title Name
Disc > Edit
A B C
a b c
1 2 3
@ ! ?
1
Title D
OFF
1
character set
Edit Ti
5 minutes
Chapt
10 minutes
15 minutes
30 minutes
60 minutes
area for enter-
ing title names
JAN/ 1 1:00AM CH12 XP
JAN/ 1 1:00AM CH12 XP
0:01:25
0:01:25
When you finish entering a title name, press
ENTER button.
2 Select a desired time using K/L buttons, then
[
]
press ENTER button.
Guide to edit title name
Select
ABC
abc
123
@ ! ?
Option window will appear.
Press
[
]
Step1 : Select a desired character set using
<space>
<space>
0
<space>
K
L buttons, then
/
A B C
a b c
1 2 3
@ ! ?
! ” # $ %
,
press ENTER button.
Disc > Edit
&
( ) *
+ , - . / : ;
< = > ?
@ [ ] ^
_ { | }
Title D
OFF
5 minutes
Chapt
10 minutes
1
*1
*1
1
Edit Ti
[
]
Step2 : Press Number buttons following by the
15 minutes
30 minutes
60 minutes
list.
ABC
DEF
abc
def
2
3
4
5
6
7
8
9
*2
*2
*2
*2
*2
*2
*2
*2
*1 Press
Yes
JAN/ 1 1:00AM CH12 XP
No
changed to the " @ " mode automatically.
*2 Press
GHI
ghi
0:01:25
will be changed to the previous input mode
automatically.
JKL
jkl
MNO
PQRS
TUV
WXYZ
mno
pqrs
tuv
・
To delete letters, press CLEAR button
repeatedly.
・To go on to the next entering area for
s
B
3 Select "Yes" using
/
buttons, then press
letters, press
wxyz
・You can enter up to 30 letters.
ENTER button.
Chapter marks will be put as you specified.
s
B
3 Select "Yes" using
/
buttons, then press
NOTE:
ENTER button.
• This operation may take a few minutes to complete.
The name you entered will be activated for the title.
NOTE:
4 After writing to disc is completed, press SETUP
• This operation may take a few minutes to complete.
button to exit DISC menu.
4 After writing to disc is completed, press SETUP
button to exit DISC menu.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
EDITING DISCS
Editing DVD-RW Discs in VR Mode
(Original)
K
L
s
B
4 Select a desired title using / / / buttons,
then press ENTER button.
Deleting Titles
Original menu will appear.
Disc > Edit > Original
DVD-RW (VR)
Title Delete
1
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
When a title is deleted from an original list in VR
mode, the disc space to record will be increased.
JAN/ 1 1:00AM CH12 XP
Caution:
0:01:25
Be advised that the titles once deleted cannot be
brought back to the disc.
K L
/
5 Select "Title Delete" using
buttons, then
press ENTER button.
Option window will appear.
SETUP
Disc > Edit > Original
Title Delete
1
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Protect OFF ON
/
/
/
Yes
JAN/ 1 1:00AM CH12 XP
No
ENTER
0:01:25
Caution:
Once erased, the material cannot be retrieved.
s
B
1 Press SETUP button. Select "DISC" using
/
s
B
6 Select "Yes" using
/
buttons, then press
buttons, then press ENTER button.
ENTER button.
DISC menu will appear.
Title will be deleted.
Disc
NOTE:
Edit
• This operation may take a few minutes to complete.
Format
Finalize
Disc Protect OFF ON
7 After writing to disc is completed, press SETUP
button to exit DISC menu.
K L
/
2 Select "Edit" using
buttons, then press
ENTER button.
Original/PlayList menu will appear.
Disc > Edit
Original
s
B
3 Select "Original" using
/
buttons, then press
ENTER button.
Original list will appear.
Disc > Edit > Original
1
2
3
JAN/1 1:00AM
4
JAN/1 2:00AM
5
JAN/1 3:00AM
JAN/1 4:00AM
JAN/1 5:00AM
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Parts of Titles
Naming Titles
DVD-RW (VR)
DVD-RW (VR)
You can delete part of a title so that the disc space
to record will increase.
You can name the titles and change the names from
this menu.
The title names will be displayed on a Title List.
Caution:
Be advised that the parts once deleted cannot be recovered.
SETUP
SETUP
/
/
/
/
/
/
ENTER
ENTER
Follow the steps [1] to [4] on page 64 to display the
Original menu.
Follow the steps [1] to [4] on page 64 to display the
Original menu.
K L
/
1 Select "Edit Title Name" using
buttons, then
K L
/
1 Select "Scene Delete" using
buttons, then
press ENTER button.
press ENTER button.
A window for entering a title name will appear.
Option window will appear.
Disc > Edit > Original > Edit Title Name
A B C
a b c
1 2 3
@ ! ?
1
Disc > Edit > Original
Title Delete
Scene Delete
1
Start
Edit Titl
End
Chapte
Preview
Delete
Index P
Protect
JAN/ 1 1:00AM CH12 XP
0:01:25
JAN/ 1 1:00AM CH12 XP
0:00:55
2 To enter a title name, follow the steps shown in
2 Press ENTER button to decide a start point, then
"Guide to edit title name" below.
press ENTER button to decide an end point.
Disc > Edit > Original > Edit Title Name
A cursor will move to "Preview." You can check a preview.
A B C
a b c
1 2 3
@ ! ?
1
character set
<Preview>
Start point End point
area for enter-
ing title names
JAN/ 1 1:00AM CH12 XP
Before
editing
0:01:25
When you finish entering a title name, press
ENTER button.
Edited
[
]
Guide to edit title name
Select
3 Select "Delete" using K/L buttons, then press
ABC
abc
123
@ ! ?
Press
[
]
Step1 : Select a desired character set using
<space>
<space>
0
<space>
ENTER button.
K
/
L buttons, then
A B C
a b c
1 2 3
@ ! ?
! ” # $ %
,
press ENTER button.
&
( ) *
Option window will appear.
+ , - . / : ;
< = > ?
@ [ ] ^
_ { | }
*1
*1
1
[
]
Step2 : Press Number buttons following by the
Disc > Edit > Original
list.
Title Delete
1
ABC
DEF
abc
def
2
3
4
5
6
7
8
9
*2
*2
*2
*2
*2
*2
*2
*2
*1 Press
button, character set will be
Scene Delete
Start
changed to the " @ " mode automatically.
!?
buttons, character set
Edit Titl
End
Chapte
Preview
*2 Press
to
GHI
ghi
Index P
Delete
will be changed to the previous input mode
automatically.
Protect
JKL
jkl
Yes
JAN/ 1 1:00AM CH12 XP
No
MNO
PQRS
TUV
WXYZ
mno
pqrs
tuv
・
To delete letters, press CLEAR button
repeatedly.
0:01:25
・To go on to the next entering area for
letters, press
button.
wxyz
・You can enter up to 30 letters.
s
B
4 Select "Yes" using
/
buttons, then press
ENTER button.
s
B
3 Select "Yes" using
/
buttons, then press
ENTER button.
Part of a title will be deleted.
The name you entered will be activated for the title.
NOTE:
• This operation may take a few minutes to complete.
NOTE:
• You cannot select "Scene Delete" when the number of chap-
ter markers in the original or playlist is more than 900.
• This operation may take a few minutes to complete.
4 After writing to disc is completed, press SETUP
5 After writing to disc is completed, press SETUP
button to exit DISC menu.
button to exit DISC menu.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
EDITING DISCS
Setting Chapter Markers
Setting Pictures for Thumbnails
DVD-RW (VR)
DVD-RW (VR)
You can put chapter markers in each title. Once a chap-
ter is marked, you can use it for chapter search.
You can set a picture to each title for a thumbnail. It
helps you to remember the contents of the title you
are playing. The beginning picture has been select-
ed as the default.
You can put a chapter marker anywhere you want.
NOTE:
• When the number of chapter markers in the original list comes
to 999 in total, you cannot add any more chapter markers.
H
G
/
SETUP
SETUP
ENTER
/
/
/
/
/
/
ENTER
PLAY B (DVD)
E
D
PAUSE
F
/
Follow the steps [1] to [4] on page 64 to display the
Original menu.
Follow the steps [1] to [4] on page 64 to display the
Original menu.
K
L
K L
/
1 Select "Index Picture Set" using
/
buttons.
1 Select "Chapter Mark" using
buttons, then
B
H
G
E
D
Use
,
,
,
, PLAY (DVD) and
press ENTER button.
PAUSE F buttons to decide the picture you want
to select as a thumbnail, then press ENTER but-
ton.
Option window will appear.
Disc > Edit > Original
Title Delete
1
Scene Delete
Edit Title Name
Chapter
Option window will appear.
Add
Delete
Chapter 1/1
Index P
Protect OFF ON
Disc > Edit > Original
JAN/ 1 1:00AM CH12 XP
Title Delete
1
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
0:01:25
F
Yes
No
K L
/
JAN/ 1 1:00AM CH12 XP
2 Select "Add" or "Delete" using
buttons, then
0:01:25
press ENTER button.
Option window will appear.
s
B
2 Select "Yes" using
/
buttons, then press
<Add>:
<Delete>:
ENTER button.
Disc > Edit > Original
Disc > Edit > Original
A picture for thumbnail will be set.
Title Delete
Title Delete
1
1
Scene Delete
Edit Title Name
Chapter
Scene Delete
Edit Title Name
NOTE:
Add
Delete
Add
Chapter
Chapter 1/1
Chapter 2/2
Delete
Index P
Index P
• This operation may take a few minutes to complete.
Protect OFF ON
Protect OFF ON
F
F
Yes
No
Yes
No
• If a selected picture for a thumbnail is deleted by deleting a
part of a title, a default picture will be selected.
JAN/ 1 1:00AM CH12 XP
JAN/ 1 1:00AM CH12 XP
0:01:25
0:01:25
3 After writing to disc is completed, press SETUP
• You cannot delete the first chapter marker of
each title.
button to exit DISC menu.
s
B
3 Select "Yes" using
/
buttons, then press
ENTER button.
A chapter marker will be added or deleted.
NOTE:
• These operations may take a few minutes to complete.
4 After writing to disc is completed, press SETUP
button to exit DISC menu.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Protecting Titles
Releasing Title Protect
DVD-RW (VR)
DVD-RW (VR)
To prevent accidental editing or erasing the titles,
you can protect them from the original menu.
You can release the title protection once you pro-
tected.
SETUP
SETUP
/
/
/
/
/
/
ENTER
ENTER
Follow the steps [1] to [4] on page 64 to display the
Original menu.
Follow the steps [1] to [3] on page 64 to display the
Original list.
K L
/
K
L
s
B
1 Select "Protect OFF ➔ ON" using
buttons,
1 Select a desired title using / / / buttons,
then press ENTER button.
then press ENTER button.
Option window will appear.
Original menu will appear.
Disc > Edit > Original
Disc > Edit > Original
Title Delete
Title Delete
1
2
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect ON OFF
Yes
JAN/ 1 1:00AM CH12 XP
No
JAN/ 1 2:00AM CH12 XP
0:01:25
0:01:25
"Protect ON ➔ OFF" is selected.
s
B
2 Select "Yes" using
/
buttons, then press
ENTER button.
2 Press ENTER button.
Option window will appear.
Disc > Edit > Original
1
Title Delete
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect OFF ON
Disc > Edit > Original
Title Delete
2
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Protect ON OFF
Yes
No
JAN/ 1 1:00AM CH12 XP
Writing to Disc
B
Yes
JAN/ 1 2:00AM CH12 XP
No
0:01:25
NOTE:
• This operation may take a few minutes to complete.
s
B
3 Select "Yes" using
/
buttons, then press
3 After writing to disc is completed, press SETUP
ENTER button.
button to exit DISC menu.
NOTE:
To protect a whole disc (DVD-RW VR mode Only):
• This operation may take a few minutes to complete.
Select "Disc Protect" from Disc menu, then select "Yes".
Refer to page 55.
4 After writing to disc is completed, press SETUP
button to exit DISC menu.
NOTE:Title Protection
• Once you protect the titles, other editing operations are not
available until you release the title protection.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
EDITING DISCS
Editing DVD-RW Discs in VR Mode
(Playlist)
K
L
s
B
4 Select a desired title using / / / buttons,
then press ENTER button.
Deleting Titles
Playlist menu will appear.
Disc > Edit > Playlist
DVD-RW (VR)
Title Delete
1
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
In VR mode, even when a title is deleted from a
Playlist, the original title will remain in an Original
list. The disc space to record will not increase.
JAN/ 1 1:00AM CH12 XP
0:01:25
K L
/
5 Select "Title Delete" using
buttons, then
press ENTER button.
SETUP
Option window will appear.
/
/
/
Disc > Edit > Playlist
Title Delete
1
ENTER
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
Yes
JAN/ 1 1:00AM CH12 XP
No
0:01:25
s
B
1 Press SETUP button. Select "DISC" using
/
s
B
6 Select "Yes" using
/
buttons, then press
buttons, then press ENTER button.
ENTER button.
DISC menu will appear.
Title will be deleted.
Disc
NOTE:
Edit
• This operation may take a few minutes to complete.
Format
Finalize
Disc Protect OFF ON
7 After writing to disc is completed, press SETUP
button to exit DISC menu.
K L
/
2 Select "Edit" using
buttons, then press
ENTER button.
Original/PlayList menu will appear.
Disc > Edit
Original
s
B
3 Select "PlayList" using
/
buttons, then press
ENTER button.
Playlist will appear.
Disc > Edit > Playlist
1
12
3
JAN/1 1:00AM
4
JAN/1 2:00AM
5
JAN/1 3:00AM
Add New
Title
Delete
Playlist
JAN/1 4:00AM
JAN/1 5:00AM
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Parts of Titles
Important
Naming Titles
DVD-RW (VR)
DVD-RW (VR)
ou can name the titles and change the names from this menu.
Y
You can delete a specific part of a title. Even when a
title is deleted from the Playlist, the original title will
remain. The disc space to record will not be increased.
The title names will be displayed on a Title List.
SETUP
SETUP
/
/
/
/
/
/
ENTER
ENTER
Follow the steps [1] to [4] on page 68 to display the
Playlist menu.
Follow the steps [1] to [4] on page 68 to display the
Playlist menu.
K L
/
1 Select "Edit Title Name" using
buttons, then
press ENTER button.
K L
/
1 Select "Scene Delete" using
buttons, then
A window for entering a title name will appear.
press ENTER button.
Option window will appear.
Disc > Edit > Playlist > Edit Title Name
A B C
a b c
1 2 3
@ ! ?
1
Disc > Edit > Playlist
Title Delete
1
Scene Dle
Start
Edit Titl
End
Chapte
Preview
JAN/ 1 1:00AM CH12 XP
Index P
Delete
0:01:25
JAN/ 1 1:00AM CH12 XP
0:00:55
2 To enter a title name, follow the steps shown in
"Guide to edit title name" below.
2 Press ENTER button to decide a start point, then
press ENTER button to decide an end point.
Disc > Edit > Playlist > Edit Title Name
A B C
a b c
1 2 3
@ ! ?
1
A cursor will move to "Preview". You can check a preview.
character set
area for enter-
ing title names
JAN/ 1 1:00AM CH12 XP
<Preview>
Start point End point
0:01:25
Before
editing
When you finish entering a title name, press
ENTER button.
Edited
[
]
Guide to edit title name
Select
ABC
abc
123
@ ! ?
Press
K L
/
3 Select "Delete" using
buttons, then press
[
]
Step1 : Select a desired character set using
<space>
<space>
0
<space>
K
/
L buttons, then
A B C
a b c
1 2 3
@ ! ?
ENTER button.
! ” # $ %
,
press ENTER button.
&
( ) *
+ , - . / : ;
< = > ?
@ [ ] ^
_ { | }
*1
*1
1
Option window will appear.
[
]
Step2 : Press Number buttons following by the
list.
Disc > Edit > Playlist
ABC
DEF
abc
def
2
3
4
5
6
7
8
9
*2
*2
*2
*2
*2
*2
*2
*2
*1 Press
button, character set will be
Title Delete
1
changed to the " @ " mode automatically.
!?
buttons, character set
Scene Dl
Start
Edit Titl
End
*2 Press
to
GHI
ghi
Chapte
will be changed to the previous input mode
automatically.
Preview
Delete
Index P
JKL
jkl
MNO
PQRS
TUV
WXYZ
mno
pqrs
tuv
・
To delete letters, press CLEAR button
repeatedly.
Yes
JAN/ 1 1:00AM CH12 XP
No
・To go on to the next entering area for
0:01:25
letters, press
button.
wxyz
・You can enter up to 30 letters.
s
B
4 Select "Yes" using
/
buttons, then press
s
B
3 Select "Yes" using
/
buttons, then press
ENTER button.
ENTER button.
Part of a title will be deleted.
The name you entered will be activated for the title.
NOTE:
NOTE:
• This operation may take a few minutes to complete.
• This operation may take a few minutes to complete.
• You cannot select "Scene Delete" when the number of chap-
ter markers in the original or playlist is more than 900.
4 After writing to disc is completed, press SETUP
5 After writing to disc is completed, press SETUP
button to exit DISC menu.
button to exit DISC menu.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
EDITING DISCS
Setting Chapter Markers
Setting Pictures for Thumbnails
DVD-RW (VR)
DVD-RW (VR)
You can put chapter markers in each title. Once a chap-
ter is marked, you can use it for the chapter search.
You can set a picture to each title for a thumbnail. It
helps you to remember the contents of the title you
are playing. The beginning picture has been select-
ed as the default.
You can put a chapter marker anywhere you want.
NOTE:
• When the number of chapter markers in the original list comes
to 999 in total, you cannot add any more chapter markers.
H
G
/
SETUP
ENTER
SETUP
/
/
/
/
/
/
ENTER
PLAY B (DVD)
E
D
PAUSE
F
/
Follow the steps [1] to [4] on page 68 to display the
Playlist menu.
Follow the steps [1] to [4] on page 68 to display the
Playlist menu.
K
L
1 Select "Index Picture Set" using
/
buttons.
B
H
G
E
D
Use
,
,
,
, PLAY (DVD), and
K L
/
1 Select "Chapter Mark" using
buttons, then
F
PAUSE buttons to decide the picture you want
to select as a thumbnail. Then, press ENTER
button.
press ENTER button.
Option window will appear.
Option window will appear and the video in the
thumbnail will begin to play.
Disc > Edit > Playlist
Title Delete
1
Scene Delete
Edit Title Name
Add
Chapter 1/1
Chapter
Delete
Index P
Disc > Edit > Playlist
Title Delete
1
Scene Delete
Edit Title Name
Chapter Mark
Index Picture Set
JAN/ 1 1:00AM CH12 XP
0:01:25
F
Yes
No
JAN/ 1 1:00AM CH12 XP
K L
/
0:01:25
2 Select "Add" or "Delete" using
buttons, then
press ENTER button.
Option window will appear.
s
B
2 Select "Yes" using
/
buttons, then press
ENTER button.
<Add>:
<Delete>:
A picture for thumbnail will be set.
Disc > Edit > Playlist
Disc > Edit > Playlist
1
Title Delete
Title Delete
1
NOTE:
Scene Delete
Edit Title Name
Scene Delete
Edit Title Name
• This operation may take a few minutes to complete.
Add
Add
Chapter 1/1
Chapter
Chapter 2/2
Chapter
Delete
Index P
Delete
Index P
• If a selected picture for a thumbnail is deleted by deleting a
part of a title, a default picture will be selected.
F
F
Yes
No
Yes
No
JAN/ 1 1:00AM CH12 XP
JAN/ 1 1:00AM CH12 XP
0:01:25
0:01:25
3 After writing to disc is completed, press SETUP
• You cannot delete the first chapter of each title.
button to exit DISC menu.
s
B
3 Select "Yes" using
/
buttons, then press
ENTER button.
A chapter marker will be added or deleted.
NOTE:
• These operations may take a few minutes to complete.
4 After writing to disc is completed, press SETUP
button to exit DISC menu.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Titles to Playlist
Deleting Playlist
DVD-RW (VR)
DVD-RW (VR)
You can add or delete a title in the playlist as you
prefer. You can add titles to a Playlist up to 99.
A Playlist can be deleted if no longer needed.
SETUP
SETUP
/
/
/
/
/
/
ENTER
ENTER
Follow the steps [1] to [3] on page 68 to display the
Playlist.
Follow the steps [1] to [3] on page 68 to display the
Playlist.
K
L
s
B
1 Select "Delete Playlist" using / / / buttons,
then press ENTER button.
K
L
s
B
1 Select "Add New Title" using / / / buttons,
Option window will appear.
then press ENTER button.
NOTE: Playlist
Original list will appear.
• Deleting a Playlist will not increase the available recording
time on disc.
Disc > Edit > Playlist > Add New Title
1
12
3
Disc > Edit > Playlist
JAN/10 10:30AM
JAN/12 5:00PM
JAN/12 8:00PM
1
12
3
JAN/1 1:00AM
4
JAN/1 2:00AM
5
JAN/1 3:00AM
Add New
Title
Delete
Playlist
Yes
No
JAN/1 4:00AM
JAN/1 5:00AM
K
L
s
B
2 Select a desired title using / / / buttons,
then press ENTER button.
s
B
2 Select "Yes" using
/
buttons, then press
The selected title will be added in Playlist.
ENTER button.
Playlist will be erased. The display will return to
TV screen.
Disc > Edit > Playlist > Add New Title
58%
Writing to Disc
Disc > Edit > Playlist
1
12
3
JAN/1 1:00AM
4
JAN/1 2:00AM
5
JAN/1 3:00AM
6
JAN/1 4:00AM
JAN/1 5:00AM
JAN/12 8:00PM
3 After writing to disc is completed, press SETUP
button to exit DISC menu.
• To delete a title from Playlist, refer to "Deleting
Titles" on page 68.
• To delete a Playlist, refer to "Deleting Playlist"
in the next section.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING DVD RECORDER
ARENTAL LOCK LEVEL SETTING
P
Some DVD-Video discs feature a Parental Lock
level. Playback will stop if the ratings exceed the lev-
els you set, it will require you to enter a password
before the disc will playback. This feature prevents
your children from viewing inappropriate material.
[A] A password has not been set yet
Setup > Playback
DVD
• If you select "No", proceed
to step [5].
TV Mode
Change Password?
Yes
No
8
Parental Lock
7
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
ish
6
inal
5
4
3
2
NOTE: Parental Lock Availability
1
Dynamic Range Control
Fast Forward with Audio
OFF
• Parental lock function may not be available to some discs.
• With some DVDs, it may be difficult to find if they are com-
patible with parental lock. Be sure to check if the parental
lock function operates as you have set.
Yes
Setup > Playback
DVD
s
B
• Select "Yes" using
/
but-
TV Mode
Password
- - - -
tons, then enter a new pass-
word using Number buttons.
Then, press ENTER button.
Your setting will be activated.
8
Parental Lock
7
6
5
4
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
ish
inal
3
SETUP
2
Dynamic Range Control
Fast Forward with Audio
1
OFF
/
/
/
ENTER
[B] A password has been set already
STOP C (DVD)
Setup > Playback
DVD
• Enter the current pass-
word using Number but-
tons.
TV Mode
etter Box
All
Password
6
5
4
3
Parental Lock
* * * *
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
ish
inal
Press STOP (DVD) button if you are playing a disc.
2
Dynamic Range Control
Fast Forward with Audio
1
OFF
1 Press SETUP button to display SETUP/DISC
menu.
SETUP/DISC menu will appear.
Setup > Playback
DVD
• If you select "No", proceed
to step [5].
s
B
2 Select "SETUP" using
/
buttons, then press
TV Mode
Change Password?
Yes
No
8
Parental Lock
7
ENTER button.
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
ish
6
inal
5
4
3
SETUP menu will appear.
2
Dynamic Range Control
Fast Forward with Audio
1
OFF
K
L
s
B
3 Select "Playback" using / / / buttons, then
press ENTER button.
Yes
Change the password
Option window will appear.
K L
/
4 Select "Parental Lock" using
buttons, then
Setup > Playback
DVD
s
B
• Select "Yes" using
/
but-
press ENTER button.
TV Mode
Password
8
- - - -
tons, then enter a new pass-
word using Number buttons,
then press ENTER button.
Your setting will be activated.
Parental Lock
7
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
ish
6
inal
5
4
Parental Lock (Default :All)
3
2
Dynamic Range Control
Fast Forward with Audio
1
Set the Parental Lock level.
OFF
Setup > Playback
DVD
NOTE: Forget Password
TV Mode
4:3 Letter Box
All
Parental Lock
• Record the password in case you forget it.
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
• Press CLEAR button to erase numbers entered incorrectly.
• When you forget the password or you want to clear all set-
tings in Parental lock, enter 4,7,3,7 using Number buttons in
option window. Password will be cleared and parental levels
will be set to All.
Dynamic Range Control
Fast Forward with Audio
ON
OFF
5 Press SETUP button to exit SETUP menu.
Setup > Playback
DVD
• Change the parental level
TV Mode
etter Box
All
K L
/
using
buttons, then
8
7
6
5
4
3
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
lish
press ENTER button.
inal
Option window will appear.
Proceed to step [A] or [B].
2
Dynamic Range Control
Fast Forward with Audio
1
OFF
72
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING SETUP MENU
ETUP MENU LIST
S
The following table shows the contents you can set, including the default settings.
Refer to the following table for useful operation.
SETUP menu Items (highlight is the default)
Contents
1.Language setting
English
French
Spanish
Disc Menu
Language
Set the language for disc menu.
Page 32
Original
English
French
Audio Language
Set the language for audio.
Set the language for subtitle.
OFF
English
French
Subtitle Language
2.Audio setting
Pages 12-13
PCM
Digital Out
Set whether the sound recorded in
96kHz will be down sampled in 48kHz.
Auto
48kHz
96kHz
Dolby Digital
PCM
Set the type of sound signal which outputs
from the digital audio output jack.
Stream
Compressing the range of sound volume.
Dynamic Range
Control
ON
OFF
Outputting the sound during play in fast
forward.
Fast Forward with
Audio
ON
OFF
100%
OSD Background
Transparency
Set the background transparency of
OSD screen.
3. OSD Display setting
Pages 14-15,
24-27
35%
25%
OSD Background
Color
1
2
3
Set the OSD screen color.
1 (Green), 2 (Blue), 3 (Red)
OSD Language
English
Français
Español
Select the language for OSD.
Screen Saver
OFF
5 minutes
10minutes
Set the time to work the screen saver
on the screen.
Set the closed caption mode.
Caption
OFF
CAPTION1
V-CHIP Setup
TV RATING
MPAA RATING
CHANGE CODE
Prevent their children from watching
inappropriate material on TV.
4.Parental setting
Page 72
ALL
Set the parental level of your DVD discs.
Set and change the password.
Parental Lock
level 8 to 1
Enter the current
four-digit password
(Change password)
NOTE:
• If you change the setting in SETUP menu, the information remains even when the power is turned off.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHERS
ROUBLESHOOTING
T
Before requesting service for this unit, check the table below for a possible cause of the problem you are
experiencing. Some simple corrections may solve the problem and restore the proper operation.
Symptom
Power
Remedy
The power does not turn on.
• Check that the AC power cord is connected securely.
Picture
• Re-connect the connecting cord securely.
• The connecting cords are damaged.
• The Setup Display appears. Press SETUP or RETURN
button to turn off the display.
There is no picture.
•
Check antenna/cable wire and the fittings at each end of the wire.
• The disc is dirty or flawed.
Picture noise appears.
• Head cleaning for VCR may be necessary. Refer to "AUTO
HEAD CLEANING".
•
Adjust tracking control for better picture by pressing
K
L
CHANNEL
/
buttons while you are playing a video tape.
•
•
Check antenna/cable wire and the fittings at each end of the wire.
Try to set the channels with "Auto Preset" in SETUP menu (page 16).
TV program reception does not fill the
screen.
• Select a channel of any TV program using the CHANNEL
K L
/
buttons.
•
Check antenna/cable wire and the fittings at each end of the wire.
• Adjust antenna.
• Adjust the picture.
TV program pictures are distorted.
•
•
Place this unit and any bunched antenna cables farther apart.
Check antenna/cable wire and the fittings at each end of the wire.
TV channels cannot be changed.
Distorted color appears on screen
• Connect the antenna cable correctly (page 10).
• Perform auto channel preset on page 16.
•
Check antenna/cable wire and the fittings at each end of the wire.
• Magnetism from nearby appliances and unshielded
speakers and geomagnetism might affect the color of the
TV picture. Move the TV/VCR/DVD away from the
appliances or unshielded speakers, the TV/VCR/DVD can
repair itself automatically. If you want to repair
immediately, unplug the power cord, then plug it in again
after 30 minutes later or so.
Sound
No sound is output.
• Adjust volume control.
• The disc is dirty or flawed.
• Re-connect all connections securely.
• The connecting cord is damaged.
• Check the connections to the amplifier input.
• The input source setting on the amplifier is incorrect.
• The unit is in Pause mode or in Slow-motion play mode.
• The unit is in fast forward or fast reverse mode.
•
If the audio signal does not come through the AUDIO OUT
COAXIAL jack, check the Audio Setup settings (pages 12-13).
• The disc is dirty or flawed.
When playing a DTS-CD, noise may come from the speakers.
This unit is not compatible with DTS-CD.
Sound is noisy.
•
• This unit is not compatible with DTS sound.
No DTS sound is output.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Playback
Remedy
The disc does not play.
• No disc is inserted.
• A blank disc is inserted.
• No cassette tape is inserted.
• The disc is upside down. Insert the disc with the labeled
side facing up.
• The disc is not correctly inserted.
•
•
The unit cannot play certain discs (such as a CD-ROM) (page 31).
The region code on the DVD VIDEO does not match the unit (page 31).
• Moisture has condensed inside the unit. Remove the disc
and leave the unit turned on at least for 2 hours until the
moisture evaporates (page 5).
• If the disc was recorded on other recorder, the unit cannot
play the disc if it was not finalized (page 54).
The disc does not start playback from
the beginning.
•
Resume play was activated (page 36). Press STOP C (DVD)
button twice.
You have inserted a disc whose Title menu or DVD menu
automatically appears on the TV screen when it is first inserted.
•
The unit starts playing from the disc
automatically.
• The DVD VIDEO features an auto playback function.
Some functions such as Stop, Search, or
Slow-motion Play cannot be performed.
•
Depending on the disc, you may not be able to do some of the
operations above. See the instruction manual supplied with the disc.
The language for the sound track
cannot be changed.
• Multilingual tracks are not recorded on the DVD VIDEO,
DVD-R or DVD-RW being played.
• The DVD VIDEO prohibits the changing of the language
for the sound track.
• Try changing the language using the DVD VIDEO's menu.
The subtitle language cannot be
changed or turned off.
• Multilingual subtitle are not recorded on the DVD VIDEO.
• The DVD VIDEO prohibits changing of the subtitles.
• Try changing the subtitle using the DVD VIDEO's menu.
The angles cannot be changed.
•
Multi-angles are not recorded on the DVD VIDEO being played.
• You are trying to change the angles when
not appear on the TV screen (page 43).
• The DVD VIDEO prohibits changing angles.
icon does
• Try changing the angle using the DVD VIDEO’s menu.
Recording/Timer recording/Editing
The channel cannot be changed from
the channel you are recording.
• You can only watch the channel currently being recorded.
Recording does not start immediately
after you press DVD RECORD or
VCR RECORD button.
• An unused DVD-R or DVD-RW was inserted. It takes a
while for the unit to automatically format a disc.
•
Make sure the tape has a record tab when you record to a
cassette tape. If needed, cover the hole with cellophane tape.
Nothing was recorded even though
you set the timer setting correctly.
• There was a power failure during recording.
•
The units internal clock stopped due to a power failure that
lasted for more than 3 seconds. Reset the clock (page 19).
• Disconnect the AC power cord from the AC outlet and
connect it again.
•
The program contains copy protection signals that restrict copying.
• The timer setting overlapped with another setting that was
set later or has priority.
Recording does not stop immediately
after you press STOP C button.
• It will take a few seconds for the unit to input disc data
before recording stops.
Timer recording is not completed or
did not start from the beginning.
• The timer setting overlapped with another setting that was
set later or has priority (page 60).
• Disc space was not enough.
Timer recording is not available.
• Make sure that the recordable tape or disc should be
inserted in the unit. If not, press POWER button.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHERS
TROUBLESHOOTING
Symptom
Remedy
Remote control
The remote control does not function.
• Batteries are weak.
• There are obstacles between the remote control unit and
the main unit.
• The remote control unit is far from the main unit.
• There are no batteries in the remote control unit.
•
The remote control is not pointed at the remote sensor on the unit.
• Check if a cassette tape is in this unit.
Others
The unit does not operate properly.
• When static electricity causes the unit to operate
abnormally, unplug the unit and wait a few minutes, then
plug it in again.
The disc tray does not open when you • It may take a few seconds for the disc tray to open after
press A OPEN/CLOSE button in the
main unit.
you have recorded or edited a disc.
• The unit may be adding disc data to the disc.
• The unit may still be recording.
My TV/VCR/DVD is showing captions
that are misspelled.
• You are watching a live broadcast and spelling errors
made by the closed captioning production company may
pass through uncorrected. A prerecorded program will not
show any misspelled words because of the normal time
available for editing the captions.
My TV/VCR/DVD will not show the text • Captions that are delayed a few seconds behind the actual
dialogue in its entirety or there is a
delay of what is being said.
are common for live broadcast. Most captioning production
companies can display a dialogue to a maximum of 220
words per minute. If a dialogue exceeds that rate, selective
editing is used to insure that the captions remain up-to-
date with the current TV screen dialogue.
My captions are scrambled with white
boxes on the TV screen.
• Interference caused by building, power lines,
thunderstorms, etc. may cause scrambled or incomplete
captions to appear.
My program guide listed a TV show as • Broadcasters may at times use a time compression
being closed captioned but none of
the captions were displayed.
process to speed up the actual program so that additional
advertising time can be given. Since the decoder cannot
read the compressed information, captions will be lost.
My prerecorded video tape does not
show any captions. The tape box
mentions it being closed captioned.
• The video tape was either an illegal copy or the tape
duplicating company accidentally left out the captioning
signals during the copying process.
My TV screen shows a black box on
certain channels.
• You are in the TEXT mode. Set CAPTION mode to
CAPTION [OFF].
"Repairing" appears on the display.
• If there is a power failure or unplugging during recording,
finalizing, formatting or editing, a Repairing process will
begin automatically just after turning the unit on again. It
may take several minutes up to about four hours.
Repairing
The DVD disc that I recorded will
not be played on other DVD units.
• You must "Finalize" all recorded discs before they can be
played on other DVD players. Without finalization, Video
mode discs cannot be played back on other DVD players
and VR mode discs cannot be played back on other VR
compatible players (See "Finalizing Discs" on page 54).
The edited Playlist can not be used
with other DVD units.
• Confirm that the disc is recorded in VR mode and finalized
properly.
• This feature may not be available according to circumstances.
I have finalized the DVD disc, but it will still • Not all DVD recordable discs will be played on all DVD
not be played back on other DVD units. units. This is inherent in the DVD recordable format.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Error message
Cause
Solution
Disc Error
--- Please eject the disc. ---
Playback feature may not be
available on this Disc.
Unplayable disc is inserted
in the DVD recorder.
Insert the standardized disc which
bear the marks on page 31.
Region Error
Playback is not authorized
because the region code of the
DVD video disc you inserted
is different.
Insert the DVD-Video disc with
region codes 1 or ALL.
--- Please eject the disc. ---
Playback is not authorized in your
region.
Parental Lock On
--- Please eject the disc. ---
The current selected parental level
Prohibits playback.
The current selected parental
level in the SETUP Menu
prohibits playback.
Check the "Parental Lock" setting
(page 72).
Recording Error
The recording function encountered
the copy prohibited program.
You cannot record copy prohibited
programs.
This program is not allowed
to be recorded.
Recording Error
This program is not
recordable in Video mode.
You are trying to record the copy-
once program onto the DVD-RW
disc in Video mode or the DVD-R
disc.
Set "DVD-RW Recording Format"
to "VR mode" (page 49-50).
Recording Error
You are trying to record onto the
disc which is unrecordable, or the
disc status prevents recording.
Insert the recordable disc, and
ensure the disc status satisfies
the recording requirements
(pages 48-55).
Can not record on this disc.
Recording Error
You are trying to record a copy-
once program onto a DVD-RW
disc which is not compatible with
CPRM.
Insert a ver.1.1 CPRM compatible
DVD-RW disc (page 49).
This program is not allowed to
be recorded on this disc.
Recording Error
You are trying to record on to the
protected disc which is set in the
Disc Setting Menu.
Release the disc protect setting
in the Disc Setting menu (page 55).
This disc is protected and not
recordable.
Recording Error
Disc is full.
(No area for new recording)
You are trying to record onto
the disc which has no space
for recording.
Insert the recordable disc with
enough recording space.
Recording Error
You are trying to record onto the
disc on which the number of
recording titles comes up to the
maximum (99).
Delete unnecessary titles
(pages 62, 64).
You cannot record more
than 99 titles on one disc.
(The maximum is 99)
Recording Error
You cannot record more the
999 chapters on one disc.
You are trying to record onto the
VR mode DVD-RW disc on which
the number of recording chapters
comes up to the maximum (999).
Delete unnecessary chapter
markers (pages 63, 66).
(The maximum is 999)
Recording Error
This disc has no space to write the
Control Information when recording
or deleting contents.
Delete unnecessary titles
(pages 62, 64).
You cannot record on this disc
as Control Information is full.
When editing has been repeatedly
performed, the control Information
area may come up to be full even
the recording area has enough space.
Recording Error
This disc's working area for
recording is full.
Insert a new disc.
You cannot record on the
disc as Power Calibration
Area is full.
When recordings are performed
repeatedly onto an unstable disc,
this area may fill up.
Recording Error
You are trying to record onto
the disc already finalized.
Release the finalizing for this disc
(page 54).
This disc is already finalized.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHERS
AINTENANCE
M
CLEANING DISCS
When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. Do not wipe in a circular motion.
•
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or
antistatic spray intended for analogue records.
CLEANING THE DISC LENS
• If this unit still does not perform properly although you refer to the relevant sections and to “TROUBLESHOOTING
GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service
Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is not used.
CABINET CLEANING
•
Wipe the front panel and other exterior surfaces of the TV/VCR/DVD with a soft cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the TV/VCR/DVD. Such chemicals may cause damage
and discoloration to the exposed surfaces.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
• Playback picture may become blurred of interrupted while the TV program reception is clear. Dirt accumulated on the video
heads after long periods of use, or the usage of rental or worn tapes can cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your TV/VCR/DVD may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-605-8453, to locate an
Authorized Service Center.
NOTES:
• Remember to read the instructions included with the video head cleaner before use.
• Clean video heads only when problems occur.
SERVICING
•
Should your TV/VCR/DVD become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts
inside. Please refer to the warranty statement page at the rear of this manual.
ANGUAGE CODE
L
Language
Code
Language
Finnish
French
Frisian
Code
Language
Lingala
Code
Language
Sindhi
Code
(Afan) Oromo
Abkhazian
Afar
6159
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6247
6265
5247
6258
6266
6367
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Afrikaans
Albanian
Amharic
Arabic
Galician
Georgian
German
Greek
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Marathi
Moldavian
Mongolian
Nauru
Nepali
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Norwegian
Occitan
Oriya
Panjabi
Pashto; Pushto
Persian
Polish
Portuguese
Quechua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian; Lettish
Rhaeto-Romance 6459
Romanian
Russian
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
Setswana
Shona
78
Download from Www.Somanuals.com. All Manuals Search And Download.
LOSSARY
G
Analog audio
Dolby Digital
Regions code
An electrical signal that directly
represents sound.
Compare this to digital audio
which can be an electrical signal,
but is an indirect representation of or multi-channel audio (up to
sound. See also "Digital audio".
The system to compress digital
sound developed by Dolby
Laboratories.
Regions associate discs and play-
ers with particular areas of the
world. This unit will only play discs
that have compatible region
codes. You can find the region
code of your unit by looking on
the rear panel. Some discs are
compatible with more than one
region (or all regions).
It offers you sound of stereo(2ch)
6 channels (5.1ch)).
Aspect ratio
MP3 (MPEG Audio Layer 3)
The width of a TV screen is rela-
MP3 is a method of compressing
tive to its height. Conventional TVs files. You can copy MP3 files on
Sampling frequency
are 4:3 (in other words, the
screen is almost square);
widescreen models are 16:9 (the
screen is almost twice as wide as
it is high).
CD-R/RW discs from the comput-
er and play the files on this unit.
The sound rate is measured by a
specified interval to turn into digi-
tal audio data. The numbers of
sampling in one second defines
as sampling frequency. The higher
the rate, the better the sound
quality as possible as it is.
Finalize
To make DVD discs, which have
been recorded on, possible to
play in other DVD players. With
Chapter
Just as a book is split up into sev- this unit, it is possible to finalize
eral chapters, a title on a DVD
disc is usually divided into chap-
ters.
DVD-R/DVD-RW discs.
SAP
(Secondary Audio Program)
PCM (Pulse Code Modulation)
See also "Title".
Second-audio channel delivered
separately from main-audio chan-
nel. This audio channel is used as
an alternate in bilingual broad-
casting.
The most common system of
encoding digital audio, found on
CDs and DAT.
CPRM
(Content Protection for
Recordable Media)
Excellent quality, but requires a lot
of data compared to formats such
as Dolby Digital and MPEG audio.
For compatibility with digital audio
recorders (CD, MD and DAT) and
AV amplifiers with digital inputs,
this unit can convert Dolby Digital
and MPEG audio to PCM.
CPRM is a copy protection sys-
tem with scramble system regard-
ing the recording of "copy-once"
broadcast programs (e.g. some
satellite broadcasts).
S-Video output
It delivers independently each sig-
nal of color(C) and luminance (Y)
to TV as video signals, so that
higher-quality picture will be
gained.
Digital audio
See also "Digital audio".
An indirect representation of
sound by numbers.
Playlist
Title (DVD only)
During recording, the sound is
measured at discrete intervals
(44,100 times a second for CD
From this list you can play con-
tents of a disc as your desired
order or in sequence. Also it is
A collection of chapters on DVD
disc.
See also "Chapter".
audio) by an analog-to-digital con- allowed to search a specific scene
verter, generating a stream of
numbers. On playback, a digital-
to-analog converter generates an
analog signal based on these
numbers. See also "Sampling fre-
quency" and "Analog audio".
directly.
Track
Audio CDs use tracks to divide up
the content of a disc. The DVD
equivalent is called a chapter. See
also "Chapter".
79
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHERS
PECIFICATIONS
S
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
CRT
27 inch in-line gun,
90˚ deflection tube
NTSC-M
Television system :
OTHER SPECIFICATIONS
Terminals
Closed caption system :§15.119/FCC
Video Heads :
Tape width :
Tape speed
SP :
Rotary four-head
1/2 inch
Antenna input:
VHF/UHF/CATV
75 ohm unbalanced (F-type)
75 ohm 4 pin mini DIN
RCA connector [ 1
RCA connector [ 2
1/8” stereo (3.5 mm)
S-Video input:
Video input:
Audio L/R input:
Headphone:
33.40mm/sec.
LP :
SLP :
16.67mm/sec. (playback only)
11.12mm/sec.
Tuner channel
TV VHF Low :
TV VHF High :
TV UHF :
CATV
Coaxial digital
audio output:
#2~#6
#7~#13
#14~#69
One pin jack,
500m Vpp (75 ohm)
Digital encoded
Remote control:
infrared light system
VHF :
5A
Operating
MID band :
SUPER band :
HYPER band :
A5~A1, A~I
J~W
W+1~W+84
temperature:
5°C to 40°C
(41°F~104°F)
Operating humidity:
Power requirements:
Power consumption
(Maximum):
5% to 85% (no condensation)
AC 120V, 60Hz
System:
DVD-Video, DVD-R/RW,
CD-DA, CD-R/RW
143W
Picture tube:
27 Pure Flat
Dimensions:
W:30-9/16” (776mm)
D:19-15/16” (507mm)
H:25-3/8” (644mm)
94.8 lbs (43kg)
Weight:
NOTE:
• The specifications and design of this product are subject to change without notice.
As an ENERGY STAR ® Partner, our company has determined that this product meets the ENERGY STAR ® guidelines for energy
efficiency. ENERGY STAR ® is a U.S. registered mark.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
81
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPAÑOL
ONEXIONES
C
Conexión de la Unidad Principal
Conexión al Sistema de Audio
• Antes de cambiar las conexiones o instalar la
unidad, todos los dispositivos deben estar apaga-
dos.
Antena
Señal de
Cable
• Lea los manuales de usuario del resto de disposi-
tivos para obtener más información.
o
Receptor con descodificador Dolby Digital
1
Clavija de entrada de
audio digital
COAXIAL
Conecte
I
O
L
(Trasera de la unidad principal)
Cable de Audio
Coaxial Digital
2
Enchufe el cable de alimentación CA de esta unidad.
(disponible en tien-
das de electrónica)
Conexión al Dispositivo de cable o al
Dispositivo de satélite
AUDIO OUT
AUDIO OUT
COAXIAL
COAXIAL
(Dispositivo de cable o
Señal de
(digital)
Dispositivo de satélite)
Cable
IN
OUT
A
U
D
I
O
O
U
T
COAXIAL
NOTA:
• Cuando reproduce un disco DVD con conexión del
TV/VCR/DVD a un receptor con descodificador Dolby
Digital, seleccione el "Dolby Digital" en la posición "Stream"
para el ajuste "Salida Digital" en el menú SETUP.
O
O
(Trasera de la unidad principal)
• La fuente de audio en un disco DVD en formato de sonido
envolvente de canal Dolby Digital 5.1 no puede grabarse en
modo de audio digital con una pletina MD o DAT.
Seleccione esta conexión cuando quiera visualizar
o grabar un canal codificado. Con esta conexión, no
se puede cambiar de canal en la unidad
TV/VCR/DVD. Puede visualizar o grabar ÚNICA-
MENTE los canales seleccionados en el dispositivo
de cable o en el dispositivo de satélite.
• Si el receptor no cuenta con un descodificador Dolby Digital,
seleccione "Dolby Digital" en la posición "PCM" para el
ajuste "Salida Digital" en el menú SETUP. La reproducción
de un DVD utilizando ajustes incorrectos puede acarrear
distorsiones de sonido y también puede dañar los altavoces.
• Seleccione "Dolby Digital" en la posición "PCM" para el
ajuste "Salida Digital" en el menú SETUP para la conexión
a una pletina MD o DAT.
• Mientras está grabando, sólo se puede visualizar
el canal grabado.
• Mediante la conexión de esta unidad a un receptor multi-
canal con un descodificador Dolby Digital, puede disfrutar
de sonido envolvente de canal Dolby Digital 5.1 de alta cali-
dad similar al obtenido en las salas de cine.
Para seleccionar canales del dispositivo de cable o
del dispositivo de satélite
1) Encienda esta unidad pulsando el botón
POWER. Posteriormente, pulse los botones
CHANNEL K/L para seleccionar el canal 3 o 4
(el mismo canal que el canal de salida del dis-
positivo de cable o del dispositivo de satélite).
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo con una
doble D son marcas comerciales de Dolby
Laboratories.
2) En el dispositivo de cable o del satélite, selec-
cione el canal que quiere visualizar o grabar.
NOTA:
• Sólo se podrá reproducir audio de DVD, CD y MP3 en la
clavija AUDIO OUT COAXIAL.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
JUSTE DEL IDIOMA DE LOS OSD
A
Puede seleccionar el idioma de los menús en pan-
talla (OSD).
4 Seleccione "Display" utilizando los botones
K
L
s
B
/ / / , después pulse el botón ENTER.
POWER
SETUP
Aparecerá la ventana de opciones.
5 Seleccione "OSD Language" utilizando los
K
L
botones / , después pulse el botón ENTER.
NOTA:
• El idioma por defecto de los OSD es el inglés.
/
/
/
6 Seleccione el idioma deseado de entre
"English", "Français" y "Español" utilizando los
ENTER
K
L
botones / , después pulse el botón ENTER.
Se activará el ajuste de idioma seleccionado.
1 Pulse el botón POWER para encender la unidad.
Preparación > Pantalla
VCR DVD
Transpa. de Fondo OSD
Color de Fondo de OSD
Ajste d Idioma de OSD
Ahorro de la Pantalla
Titulo
35%
1
2 Pulse el botón SETUP para acceder al menú
English
SETUP/DISC.
Français
s
Español
OFF
Aparecerá el menú SETUP/DISC.
Ajuste de V-CHIP
s B
3 Seleccione "SETUP" utilizando los botones / ,
después pulse el botón ENTER.
7 Pulse el botón SETUP para salir del Menú de
Aparecerá el menú SETUP.
Preparación.
JUSTE DE CANALES
A
K
L
CHANNEL
/
CH 18
Numéricos
Ahora en Ajuste Auto
SETUP
/
/
/
NOTA:
• Si se cancela la operación Ajuste Auto antes de completar el
ajuste previo, puede que algunos canales que no se hayan
ajustado previamente no se encuentren disponibles.
ENTER
RETURN
1 Pulse el botón SETUP para acceder al menú
•
La selección dependerá de cómo recibe los canales de televisión.
SETUP/DISC.
5 Pulse el botón SETUP para salir del menú.
Aparecerá el menú SETUP/DISC.
Puede seleccionar únicamente los canales
memorizados en esta unidad utilizando los
s B
2 Seleccione "SETUP" utilizando los botones / ,
después pulse el botón ENTER.
K
L
botones CHANNEL / .
Aparecerá el Menú de Preparación.
Para seleccionar un canal:
Puede seleccionar un canal introduciendo direc-
tamente el mismo utilizando los botones
numéricos del mando a distancia.
3 Seleccione "Channel" utilizando los botones
K
L
s
B
/ / / , después pulse el botón ENTER.
Aparecerá el menú Ajuste de Canal.
Notas para la utilización de los botones
4 Seleccione "Ajuste Auto" utilizando los botones
numéricos:
• Cuando seleccione los canales de cable superiores al
número 99, introduzca los números de canal como dígito de
tres cifras. (Por ejemplo: 117, pulse 1,1,7)
K
L
/ , después pulse el botón ENTER.
La unidad comenzará a realizar una búsqueda
de los canales disponibles en su zona.
• Debe introducir delante de los números de canales de una
cifra el número cero (Por ejemplo: 02, 03, 04 y en adelante).
Para cancelar el Ajuste Auto durante la búsqueda:
•
Puede seleccionar el modo de entrada en línea (“AUX”). Para
seleccionar “AUX” pulse [0], [0]. Más información en la página 56.
Pulse el botón RETURN o el botón SETUP para
cancelar la operación.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPAÑOL
UNCIONES DE TELEVISIÓN
F
Visualización de un programa de
televisión
2 Seleccione el canal deseado utilizando los
K L
/
botones CHANNEL
o los botones numéri-
cos del mando a distancia.
Si la unidad TV/VCR/DVD está conectada a un
dispositivo de cable o de satélite, el TV/VCR/DVD
deberá encontrarse en el canal 3 o 4 y, en tal
caso, el canal que desee visualizar deberá selec-
cionarlo desde el dispositivo de cable o del
satélite.
POWER
K
X
L
Y
CHANNEL
/
Numéricos
VOLUME
/
3 Ajuste el volumen al nivel deseado utilizando los
X
Y
botones VOLUME / .
4 Ajuste el control de la imagen para obtener un
1 Pulse el botón POWER para encender la unidad.
aspecto natural.
5 Cuando termine de ver la televisión, pulse el
botón POWER para apagar el televisor.
UNCIONES VCR
F
Reproducción
2 Introduzca la cinta pregrabada y pulse el botón
PLAY B (VCR) para comenzar la reproducción.
VCR
NOTA:
• Cuando se introduce una cinta sin etiqueta de grabación, la
reproducción comenzará automáticamente.
POWER
• El rastreo de pistas se ajustará automáticamente cuando
comience la reproducción. Para ajustarlo manualmente,
K
L
CHANNEL
/
K
L
pulse los botones CHANNEL
/
de la unidad principal o
K
L
los botones CHANNEL
/
del mando a distancia.
3 Pulse el botón STOP C (VCR) para detener la
reproducción.
/
/
/
A
4 Pulse el botón C STOP/ EJECT de la unidad
principal para extraer la cinta.
STOP C (VCR)
1 Pulse el botón POWER para encender la unidad.
PLAY B (VCR)
84
Download from Www.Somanuals.com. All Manuals Search And Download.
UNCIONES DE DVD
F
Reproducción
Modo de VR:
DVD-V DVD-R DVD-RW (Video)
Original
1
12
3
DVD-RW (VR)
CD
MP3
ENE/1 12:00AM
4
ENE/1 1:00AM
5
ENE/1 2:00AM
POWER
ENE/1 3:00AM
ENE/1 4:00AM
Botón DISC MENU
Playlist
1
12
3
TOP MENU
ENTER
DISC MENU
ENE/1 12:00AM
4
ENE/1 1:00AM
5
ENE/1 2:00AM
/
/
/
ENE/1 3:00AM
ENE/1 4:00AM
STOP C (DVD)
MP3:
Lista de Archivos MP3
NOMBRE DEL DISCO
1 Pulse el botón POWER.
NOMBRE DE LA CARPETA 1
NOMBRE DE LA CARPETA 2
NOMBRE DE LA CARPETA 3
NOMBRE DE LA CARPETA 4
NOMBRE DE LA CARPETA 5
NOMBRE DE LA CARPETA 6
A
2 Pulse el botón OPEN/CLOSE de la unidad
principal para abrir la bandeja de discos.
1
2
NOMBRE DEL ARCHIVO 1
NOMBRE DEL ARCHIVO 2
1/2
La bandeja de discos se abrirá.
NOTA:
3 Coloque el disco en la bandeja de discos con la
etiqueta hacia arriba y asegúrese de que se
ajuste perfectamente a la guía. Pulse el botón
• Pulse el botón TOP MENU para salir del menú.
• Para discos DVD-R (Modo de Video) y DVD-RW (Modo de
Video) que ya han sido ultimados, se mostrará una lista de
títulos en lugar de pequeñas reseñas tal y como se muestra
posteriormente.
A
OPEN/CLOSE otra vez para cerrar la bande-
ja de discos.
NOTA:
Menú Título
1
ENE/1 12:24AM CH96 XP
• Esta operación puede tardar unos minutos en completarse.
• Puede que algunos discos se reproduzcan automática-
mente.
• Si reproduce un disco de vídeo DVD, puede que aparezca
un menú.
5 Seleccione el título deseado pulsando los
K
L
s
B
botones / / / , posteriormente pulse el
guía de la
bandeja de
discos
botón ENTER.
Comenzará la reproducción.
6 Pulse el botón STOP C (DVD) para detener la
4 Pulse el botón TOP MENU para acceder al
reproducción.
menú de títulos.
A
Para extraer el disco, pulse el botón OPEN/CLOSE
Puede cambiar entre los modos "Original" o
"Playlist" de VR utilizando el botón DISC MENU.
para abrir la bandeja del disco y después retírelo
antes de apagar la unidad.
Modo de Video:
Lista de Títulos
1
12
3
ENE/1 12:00AM
4
ENE/1 1:00AM
5
ENE/1 2:00AM
ENE/1 3:00AM
ENE/1 4:00AM
85
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPAÑOL
RABACIÓN FÁCIL DE DVD
G
Lo que sigue a continuación de ayudará a comprender fácilmente cómo grabar discos DVD.
NOTA
• Asegúrese de haber completado las conexiones y de haber colocado pilas en el mando a distancia.
Paso 1: Escoja el tipo de
disco
Paso 3: Seleccione la
velocidad de
Paso 2: Introduzca
un disco
grabación
en blanco
Encienda la unidad
Existen varios tipos de discos de DVD
grabables entre los que escoger. Escoja
el tipo seleccionado de entre los “Tipos
de disco DVD” de esta página.
Esta unidad sólo puede grabar sobre
los siguientes tipos de discos.
1
2
3
Para seleccionar la
Abra la bandeja
de discos
Cierre la bandeja
de discos
velocidad de grabación,
pulse una vez el botón
REC SPEED, posterior-
mente, cambie la veloci-
dad de grabación pul-
Mando a distan-
1
K
L
sando los botones
/
.
(o)
2
* Esta unidad no puede grabar sobre
los siguientes discos.
• DVD-R General Ver 2.0 / 8x
• DVD-RW Ver 1.2 / 2-4x CPRM com-
patible
Por ejemplo, cuando desee grabar
repetidamente sobre el mismo disco
o cuando desee editar el disco
después de la grabación, escoja el
tipo de disco regrabable DVD-RW.
Cuando desee guardar grabaciones
sin efectuar cambios, puede escoger
un disco no regrabable DVD-R.
SP 1:01 Rem.
3
Cargando
NOTA:
• Esta operación puede llevar-
le unos minutos.
Tipos de disco DVD
Importante
Formatee el disco
.
: El más adecuado.
: Puede utilizarse.
: Algunas funciones están limitadas.
: No puede utilizarse.
DVD-RW Video
DVD-R
Desea
DVD-RW VR
Introduzca el disco en la unidad.
Posteriormente, formatee el disco
desde el menú SETUP. Se encon-
trarán disponibles las opciones de
formateo de Vídeo (Modo de
Video) o formateo de grabación
de Vídeo (Modo de VR) en fun-
ción del tipo de disco introducido.
Esto es esencial para preparar el
disco para la grabación. Más infor-
mación en las páginas 48-49.
* Cuando efectúa el forma-
teo, todos los contenidos
del disco se borran.
Grabar programas de televisión
Reutilizar borrando contenidos no deseados
Editar los contenidos grabados
Editar / Grabar desde un equipo conectado
Copiar discos para su distribución
Reproducir en otro equipo de DVD
*1
*1
Características
DVD-RW VR
DVD-RW Video
DVD-R
Grabación
¿Regrabable?
Sí
Sí
Sí
Sí
Sí
Sí
Sí
No
Sí
Puede crear capítulos en intervalos fijos (auto.)
Puede crear capítulos allí donde lo desee (manual)
Puede grabar imágenes de 16:9
Puede grabar programas de una sola copia
Edición
No
Sí
No
Sí
No
No
Puede efectuar funciones de edición básicas
Puede efectuar funciones de edición avanzadas (Edición de Playlist)
Sí
Sí
Sí
Sí
No
No
Finalización del disco
*1
El DVD-RW (Modo de VR) sólo puede reproducirse
en equipos de DVD compatibles con VR.
NOTA:
Para más información acerca de las funciones
anteriormente descritas y sus restricciones implícitas,
diríjase a las explicaciones contenidas en el manual.
Después de la grabación, deberá
finalizar los discos DVD grabados
en esta unidad antes de poder
reproducirlos en otros reproductores
de DVD. Diríjase a la página 54.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Paso 4: Seleccione
el canal
Paso 5: Pulse el
botón DVD
RECORD
Paso 6: Detenga la
Grabación
deseado
58%
Escrit de datos
DISC
NOTA:
• Esta operación pude llevarle var-
ios minutos.
DISC
I
CH 1
Reproducción de los contenidos grabados
Comenzar la
Grabación.
Detener /
Comenzar
Detener la
Grabación.
Puede seleccionar el título que desee reproducir desde un menú mostra-
do y comenzar inmediatamente la reproducción. Los contenidos graba-
dos son muy accesibles en un disco, el procedimiento es realmente sen-
cillo cuando selecciona un título en un capítulo del menú de pantalla.
Título 1
Título 2
¿Qué son los títulos y los capítulos?
Los contenidos del disco DVD se dividen normalmente en
títulos. Los títulos pueden dividirse además en capítulos.
Capítulo 1 Capítulo 2 Capítulo 3 Capítulo 1 Capítulo 2
Edición del disco grabado
Le resultará muy fácil editar discos. Esta unidad ofrece sencillas funciones de edición que sólo se
encuentra disponibles en discos DVD-R/RW.
Puede editar lo siguiente a partir de una lista de Títulos.
• Nombrar títulos
• Establecer imágenes para pequeñas reseñas (Modo de VR)
• Establecer / eliminar marcadores de capítulo
• Borrar partes de título o escena (Modo de VR)
Borrar título : Esta función borra una escena completa de forma permanente del disco.
Borrar escena : Esto permite al usuario editar una escena específica (p.e., anuncios publicitarios).
Original y Playlist (Modo de VR)
Puede editar las grabaciones en una Playlist sin modificar las grabaciones originales. Las
Listas de Reproducción no ocupan mucho espacio en el disco.
¿Para qué sirve “Original” o “Playlist”?
A lo largo de este manual, encontrará los términos Original y Playlist para referirse al contenido
real de la versión editada.
• Contenido Original se refiere a lo que realmente hay grabado en el disco.
• Contenido de la Playlist se refiere a la versión editada del disco, cómo debe reproducirse el
contenido original.
Finalización del Disco
• Esto le permitirá reproducir un disco grabado en nuestra unidad en otro reproductor de DVD.
Sin efectuar esta operación, no podrá reproducirlo en otro reproductor.
• Tras finalizar un disco, si la grabación se encontraba en Modo de Video, no podrá editar
ninguna información dentro del disco.
• Si ha grabado en Modo de VR en un disco DVD-RW, entonces podrá editar el disco después
de la finalización. Véase la página 54.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to
any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP. or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT
FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,
please call 1-800-605-8453 or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-605-8453
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
1EMN20176
T2021UB ★★★★★
Download from Www.Somanuals.com. All Manuals Search And Download.
|