OWNER’S
MANUAL
COLOR TV/VCR/DVD TRIPLE COMBO
(27 inch)
6727DF
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-968-3429.
Please read before using this equipment
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
13. Outdoor Antenna grounding - If an outside antenna
or cable system is connected to the unit, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up sta-
tic charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect
to proper grounding of the mast and supporting struc-
ture, grounding of the lead-in wire to an antenna dis-
charge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding elec-
trodes, and requirements for the grounding electrode.
(Fig. A)
19. Damage Requiring Service - Unplug this unit from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged or
frayed.
b. If liquid has been spilled, or objects have fallen into the
unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the operating instructions, as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified techni-
cian to restore the unit to its normal operation.
14. Lightning - For added protection for this unit receiver
during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable system.
This will prevent damage to the unit due to lightning
and power-line surges.
e. If the unit has been dropped or damaged in any way.
f. When the unit exhibits a distinct change in perfor-
mance, this indicates a need for service.
15. Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be
taken to keep from touching such power lines or cir-
cuits as contact with them might be fatal.
20. Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer that
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, injury to persons or other hazards.
21. Safety Check - Upon completion of any service or
repairs to this unit, ask the service technician to per-
form routine safety checks to determine that the unit is
in proper operating condition.
16. Overloading - Do not overload wall outlets and exten-
sion cords as this can result in a risk of fire or electric
shock.
17. Object and Liquid Entry - Never push objects of any
kind into this unit through openings as they may touch
dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of
any kind on the unit.
22. Heat - This unit product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
18. Servicing - Do not attempt to service this unit yourself
as opening or removing covers may expose you to dan-
gerous voltage or other hazards. Refer all servicing to
qualified service personnel.
- 3 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
LASER SAFETY
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public perfor-
mance and lending of discs are prohibited.
This product incorporates copyright protection tech-
nology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise autho-
rized by Macrovision. Reverse engineering or dis-
assembly is prohibited.
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to ser-
vice this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
RADIO-TV INTERFERENCE
This Class B digital apparatus complies with
Canadian ICES-003.
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
Cet appareil numérique de la classe B est con-
forme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
Batteries should never be thrown away or inciner-
ated but disposed of in accordance with your local
regulations concerning chemical wastes.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other unit has the same serial
number as yours. You should record the number and other vital information here and retain this book as a per-
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
- 4 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
LOCATION
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a unit which has
moisture, it may damage the DVD and the unit.
Therefore when the condensation occurs inside the
unit, turn the unit on and allow at least 2 hours for the
unit to dry out.
For safe operation and satisfactory performance of
your unit, keep the following in mind when selecting
a place for its installation:
Shield it from direct sunlight and keep it away from
sources of intense heat.
•
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top or bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
•
•
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some head-
ings and notes in this manual, with the following
meanings.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place the unit near strong magnetic fields.
Avoid moving the unit to locations where tempera-
ture differences are extreme.
Be sure to remove disc and unplug the AC power
cord from the outlet before carrying the unit.
•
•
•
•
TV/VCR
: Description refers to TV/VCR operation (in the
TV/VCR mode).
•
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
AVOID THE HAZARDS OF
CD
ELECTRICAL SHOCK AND FIRE
: Description refers to playback of Audio CDs
(in the DVD mode).
Do not handle the power cord with wet hands.
•
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
If by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
•
QUICK
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
•
Do not put your fingers or objects into the unit disc
loading tray.
•
Do not place anything directly on top of the unit.
•
SUPPLIED ACCESSORIES
Remote Control Unit
Batteries
Owner’s Manual
Owner's Manual
NE209UD
2 AA Batteries
1EMN20316
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our
help line mentioned on the front page.
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators
(Splitter). Contact your local electronics store for these items.
•
•
- 5 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SLOW MOTION . . . . . . . . . . . . . .25
STILL PICTURE . . . . . . . . . . . . . .25
VERTICAL HOLD CONTROL . . .25
C IMPORTANT SAFEGUARDS . . . . .2
C SEARCH FUNCTION . . . . . . . . . . .38
TRACK SEARCH . . . . . . . . . . . . .38
TITLE / CHAPTER SEARCH . . . .38
TIME SEARCH . . . . . . . . . . . . . . .38
MARKER SETUP SCREEN . . . . . .38
C PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
C SPECIAL PLAYBACK . . . . . . . . . .26
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
RENTAL PLAYBACK . . . . . . . . . .26
WARNING . . . . . . . . . . . . . . . . . . . .5
AUTO REPEAT PLAYBACK . . . . .26
C
SPECIAL PLAYBACK FUNCTION . . .39
REPEAT . . . . . . . . . . . . . . . . . . . . .39
PROGRAM . . . . . . . . . . . . . . . . . . .39
RANDOM PLAYBACK . . . . . . . . .39
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C SEARCH . . . . . . . . . . . . . . . . . . . . .27
ZERO RETURN . . . . . . . . . . . . . . .27
PICTURE SEARCH . . . . . . . . . . . .27
TIME SEARCH . . . . . . . . . . . . . . .27
INDEX SEARCH . . . . . . . . . . . . . .28
C SUPPLIED ACCESSORIES . . . . . . .5
C TABLE OF CONTENTS . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C CHANGING THE SETTINGS . . . .40
SUBTITLE LANGUAGE . . . . . . . .40
AUDIO LANGUAGE . . . . . . . . . . .40
STEREO SOUND MODE . . . . . . . .40
CAMERA ANGLE . . . . . . . . . . . . .41
BLACK LEVEL SETTING . . . . . . .41
VIRTUAL SURROUND . . . . . . . . .41
C SPECIAL FEATURES . . . . . . . . . .28
REAL TIME TAPE COUNTER . . .28
AUTO REWIND-EJECT . . . . . . . .28
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . . . . .9
INSTALLING THE BATTERIES . .11
C RECORDING . . . . . . . . . . . . . . . . .29
C PREPARATION FOR USE . . . . . . .12
NORMAL RECORDING . . . . . . . .29
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .12
C
THE ON-SCREEN INFORMATION . .42
SKIPPING UNWANTED SCENES
DURING RECORDING . . . . . . . . .29
CONNECTING TO FRONT A/V
INPUT JACKS . . . . . . . . . . . . . . . .13
C CHANGING THE DVD SET UP
ITEMS . . . . . . . . . . . . . . . . . . . . . . .43
OTR (One Touch Recording) . . . . . .30
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH DIGI-
TAL INPUT JACKS (for DVD) . . .13
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .30
CUSTOM MENU . . . . . . . . . . . . . .43
LANGUAGE SETTING . . . . . . .43
DISPLAY SETTING . . . . . . . . . .44
AUDIO SETTING . . . . . . . . . . .44
PARENTAL CONTROL . . . . . . .45
OTHER SETTINGS . . . . . . . . . .45
INITIALIZE . . . . . . . . . . . . . . . . . .45
C TIMER RECORDING . . . . . . . . . . .31
CONNECTING TO A DOLBY
DIGITAL DECODER (for DVD) . .14
AUTOMATIC
TIMER RECORDING . . . . . . . . . .31
TV/VCR SECTION
AUTO RETURN . . . . . . . . . . . . . . .33
C TV OPERATION AND SETTINGS .15
WATCHING A TV PROGRAM . . .15
DEGAUSSING . . . . . . . . . . . . . . . .15
PICTURE CONTROL . . . . . . . . . . .15
SLEEP TIMER . . . . . . . . . . . . . . . .16
CLOSED CAPTION SYSTEM . . . .16
CHANNEL SET UP . . . . . . . . . . . .17
C ON SCREEN DISPLAY . . . . . . . . .34
C TROUBLESHOOTING GUIDE . . .46
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .34
C MAINTENANCE . . . . . . . . . . . . . . .49
DVD SECTION
DISC HANDLING . . . . . . . . . . . . .49
C SPECIFICATIONS . . . . . . . . . . . . .50
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .51
C WARRANTY . . . . . . . . . . .Back Cover
C ABOUT THE DISCS . . . . . . . . . . . .35
PLAYABLE DISCS . . . . . . . . . . . .35
UNPLAYABLE DISCS . . . . . . . . . .35
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . . . . .18
C PLAYING A DISC . . . . . . . . . . . . . .36
BASIC PLAYBACK . . . . . . . . . . . .36
GENERAL FEATURES . . . . . . . . .36
DISC MENU . . . . . . . . . . . . . . . . .36
TITLE MENU . . . . . . . . . . . . . . . . .36
RESUME . . . . . . . . . . . . . . . . . . . .37
PAUSE . . . . . . . . . . . . . . . . . . . . . .37
STEP BY STEP PLAYBACK . . . . .37
DAYLIGHT-SAVING TIME . . . . . .19
V-CHIP SET UP . . . . . . . . . . . . . . .20
TV RATING SET UP . . . . . . . . .20
MPAA RATING SET UP . . . . . .21
CHANGE ACCESS CODE . . . . .21
MENU LANGUAGE . . . . . . . . . . .21
C MTS (Multi-Channel Television
sound) SYSTEM . . . . . . . . . . . . . . .22
FAST FORWARD /
FAST REVERSE . . . . . . . . . . . . . .37
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .22
SLOW FORWARD /
SLOW REVERSE . . . . . . . . . . . . . .37
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .22
ZOOM . . . . . . . . . . . . . . . . . . . . . .37
SELECTING THE MTS SYSTEM .23
C VIDEO CASSETTE . . . . . . . . . . . . .24
C PLAYBACK . . . . . . . . . . . . . . . . . . .25
NORMAL PLAYBACK . . . . . . . . .25
TRACKING ADJUSTMENT . . . . .25
- 6 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
TV/VCR Mode
Hi-Fi system – The Hi-Fi stereo recording system
offers you excellent sound quality with a dynamic
range of 80dB, frequency response from 20Hz to
20kHz and 0.005% wow and flutter.
Rotary 4-head Record/Playback System – Four
heads ensure excellent picture quality and special
effects playback.
Index Search – Fast-forwards to start of next record-
ing.
Slow Motion – View recorded program at slower
than normal speed.
2 Step picture search operation – You can view a
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode, only high speed is avail-
able.
Three different playback tape speeds : SP/LP/SLP
Two different recording tape speeds : SP/SLP
Auto Head Cleaner – Automatically cleans video
heads as you insert or remove a cassette.
Zero Return – The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
Still – “Freeze” the picture at any time, for close
viewing of a particular scene.
Digital Auto Tracking (DTR) – Automatically
adjusts the tracking for each tape you play.
Rental play mode – Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat – Allows you to repeat the playing of
a tape indefinitely without hitting [PLAY O].
Time search – Lets you set the unit to advance the
tape by entering the desired playback time you want
to skip.
OTR (One Touch Recording) – Instant timed
recording from 30 to 480 minutes is possible by
hitting [REC/OTR].
1 Year, 8 events (including Daily and Weekly)
Timer Recording – The built-in timer allows you
to record up to 8 programs at different times on
different channels up to 1 year in advance. The
Daily timer allows recordings to be made of daily
broadcasts and the Weekly timer allows recording
to be made once a week up to the end of the tape.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Infrared remote control
Trilingual on screen TV/VCR setup display
selectable in English, Spanish or French
•
•
Real time counter – This shows the elapsed record-
ing or playback time in hours, minutes and seconds.
The “–” indication will appear when the tape is
rewound further than the tape counter position
“0:00:00”.
181 channel capability PLL frequency synthesiz-
er tuner with direct station call (A converter may
be necessary to view scrambled cable channels.)
Auto Clock Setting – Allows you to set the clock
function from a PBS broadcast station.
Closed Caption Decoder – You may view special-
ly labeled (cc) TV programs, movies, news, prere-
corded tapes, etc. with either a dialogue caption or
text display added to the program.
•
•
•
•
•
•
Auto power on and off system – Automatically
turns on the unit when you insert the cassette, turns
off after auto-rewind and ejects when the begin-
ning of the tape is reached.
•
Auto rewind when the end of a tape is reached
(This function doesn’t occur when using timer
recording.)
Smooth mode change – TV/VCR mode and DVD
mode automatically changes without control.
•
•
Auto return – After timer recording is finished, the
unit can return to the beginning of the recording.
Sleep timer – Allows you to have the unit auto-
matically turn off at a desired time.
Timer Program Extension – Allows you to shift
the time schedule for automatic timer recording.
V-CHIP – Enables parents to prevent their children
from watching inappropriate material on TV.
•
•
•
•
- 7 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Mode
¡Dolby Digital sound
DVD or Audio CD.
This unit can handle Dolby Digital surround sound
having 5.1 channels when connected to a Dolby
Digital decoder.
¡On-screen display
Information about the current operation can be dis-
played on a TV screen, allowing you to confirm the
currently active functions (such as program play-
back), on the TV screen using the remote control.
¡Still/fast/slow/step playback
Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
¡Search
Chapter search / Title search / Track search / Time
search
¡Repeat
¡Random playback for Audio CD
This unit can shuffle the order of tracks to play them
in random order.
Chapter / Title / Track / All / A-B
¡Program playback for Audio CD
You can program the order of tracks to play them in
any desired order.
¡Zoom
Magnified screen can be displayed.
¡Marker
¡DVD menus in a desired language
You can display DVD menus in a desired language,
if available on a DVD.
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which
the play was stopped.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no
input from the unit for 5 minutes in the stop mode.
After the screen saver program is activated for 15
minutes, the power automatically turns off.
¡Virtual Surround
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Subtitles in a desired language
You can select a desired language for the display
subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc
contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available
on a disc.
¡Parental lock
You can set the control level to limit playback of
discs which may not be suitable for children.
¡Automatic detection of discs
This unit automatically detects if the loaded disc is
- 8 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL - [Fig.1]
DVD buttons
TV/VCR buttons
REC/OTR REW PLAY F.FWD
POWER
SELECT
AUDIO
VOLUME
SKIP
PLAY
SKIP
STOP
OPEN/CLOSE
CHANNEL
STOP/EJECT
HEADPHONE VIDEO
L
R
DVD
TV/VCR
SEARCH
1
2
3
4
3
5
6
7
8 9 10 11 12 13 14 4 15 16 17 18 19 20
21
5.STOP P Button [TV/VCR P.25 / DVD P.37]
(Front panel) Stops operation of the disc.
[Fig. 2]
- REMOTE CONTROL -
(Remote control) Stops operation of the disc or
tape contents.
6.OPEN/CLOSE N Button [DVD P.36]
POWER PICTURE SLEEP SELECT
Hit to insert a disc into or remove it from the tray.
1
9
44
22
7.Disc loading tray
8.DVD Indicator
Lights up during DVD mode.
1
4
2
5
8
0
3
6
CH.
11
23
7
PAUSE
9
+100
9.SELECT Button [TV/VCR P.15] [DVD P.36]
Hit to change to TV/VCR mode, external input
mode or DVD mode. You can see the mode
(TV/VCR or DVD) on the front panel indicator.
10.TV/VCR Indicator
VOL.
2
+10
24
SPEED C.RESET
ZOOM
MUTE
43
42
25
26
(DVD) 3
PLAY
STOP
3 (DVD)
Lights up during TV/VCR mode.
15 (TV/VCR)
(TV/VCR) 414
11. CHANNEL (CH.) X / Y Buttons
DISC
MENU
5
41
40
39
38
RECORD
Press to select memorized channels.
13
12. Recording Indicator
DISPLAY
SETUP
ENTER
27
Flashes during recording. Lights up in the stand-
by mode for Timer Recording.
TITLE
RETURN
28
29
30
CLEAR SEARCH MODE REPEAT
A-B
13. REC/OTR Button (Front Panel) [TV/VCR P.30]
Hit to start manual recording. Hit repeatedly to
start One Touch Recording.
37
AUDIO SUBTITLE ANGLE
MODE
31
32
33
36
35
34
RECORD Button (Remote Control) [TV/VCR P.29]
Hit to start manual recording.
14. REW b Button (for TV/VCR) [TV/VCR P.27]
Hit to rewind the tape or to view the picture rapid-
ly in reverse during playback mode. (Rewind
Search)
15. F.FWD a Button (for TV/VCR) [TV/VCR P.27]
Hit to rapidly advance the tape or to view the pic-
ture rapidly in forward during playback mode.
(Forward Search)
1.POWER Button [TV/VCR P.15 / DVD P.36]
Hit to turn the power on and off.
2.VOLUME (VOL.) X / Y Buttons
Press to control the volume level for the DVD and TV.
16. STOP/EJECT
P
N Button [TV/VCR P.24, 27]
3.SKIP U / T Buttons (for DVD) [DVD P.38]
Press once to skip chapters or tracks to a desired
point.
SEARCH h / g Buttons (for DVD) [DVD P.37]
Press and hold to change forward or reverse play-
back speed.
Hit to stop the tape motion. Hit in the stop mode
to remove tape from the unit.
17. Remote sensor window
18. HEADPHONE Jack
To connect headphone (not supplied) for personal
listening.
4.PLAY O Button [TV/VCR P.25 / DVD P.36]
Starts playback of the disc or tape contents.
- 9 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
- REAR PANEL - [Fig.3]
ANT.
AUDIO OUT
COAXIAL
46
45
47
19. VIDEO input Jack
31. MODE Button [DVD P.39, 41]
Connect to the video output jack of a video
camera or VCR.
Hit to call up the program screen or the random
screen in the stop mode.
Hit to call up the Black Level Setting screen or
the Virtual Surround screen during playback.
20. AUDIO L/R input Jacks
Connect to the audio output jacks of a video
camera or VCR.
32. SEARCH MODE Button [DVD P.38]
Hit to locate a desired point.
21. Cassette compartment
33. AUDIO Button
22. PICTURE Button
Hit to adjust the picture.
TV/VCR Mode:[P.23]
Hit to select a desired sound mode when watching
a TV program or playing or recording a cassette
tape.
DVD Mode:[P.40]
Hit to select a desired audio language or sound
mode.
23. Number Buttons
TV/VCR Mode: [P.17]
Press two digits to directly access the desired
channel.
Remember to hit [0] before a single digit channel.
+100 Button–
Hit to select cable channels which are higher than
99.
34. SUBTITLE Button [DVD P.40]
Hit to select a desired subtitle language.
DVD Mode: [P.38]
Hit to enter the desired number.
+10 Button–
Hit to enter the desired numbers which are higher
35. REPEAT Button [DVD P.39]
Repeats playback of the current disc, title, chapter,
or track.
36. ANGLE Button [DVD P.41]
than 9.
Hit to change the camera angle to see the sequence
being played back from a different angle (if avail-
able).
24. PAUSE F Button [TV/VCR P.25 / DVD P.37]
Pauses the current disc or tape operation.
25. SPEED Button [TV/VCR P.29]
Hit to choose the desired recording speed:
SP/SLP.
37. A-B Button [DVD P.39]
Repeats playback of a selected section.
38. RETURN Button [TV/VCR P.32] [DVD P.38]
26. C.RESET Button [TV/VCR P.27]
Hit to reset counter to “0:00:00”.
Hit to cancel a setting of timer program. (Refer to
page 32.)
Returns to the previous screen in the setup menu.
39. ENTER Button [TV/VCR P.16] [DVD P.36]
Hit to accept a setting.
40. K / L / { / B Buttons
TV/VCR Mode:[P.15]
27. DISPLAY Button
TV/VCR Mode:[P.22]
Press to select a setting mode from the menu on
the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:[P.36]
Displays the counter or the current channel num-
ber and current time on the TV screen.
DVD Mode:[P.42]
Displays the current status on the TV screen.
Press to select a menu item.
28. SETUP Button [TV/VCR P.16] [DVD P.43-45]
41. DISC MENU Button [DVD P.36]
Hit to enter or exit the setup menu of TV or DVD.
Calls up the DVD menu.
29. TITLE Button [DVD P.36]
42. ZOOM Button [DVD P.37]
Displays the title menu.
Enlarges part of a DVD-reproduced image.
30. CLEAR Button [DVD P.38]
Hit to clear or cancel a setting currently entered.
- 10 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
43. MUTE Button [TV/VCR P.15]
46. Power cord [P.15]
Mutes the sound. Hit it again to restore sound.
Connect to a standard AC outlet (120V/60Hz).
NOTE:
44. SLEEP Button [TV/VCR P.16]
Remove the power cord from the hook to
avoid breaking a wire before you connect to a
standard AC outlet.
•
Sets the Sleep Timer.
45. ANT(ENNA). Jack [P.12]
Connect to an antenna, cable system or satellite
system.
47. AUDIO OUT COAXIAL Jack [P.13]
Connect to the digital input of an external
amplifier or decoder (for DVD Audio only).
NOTE:
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
•
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
[BATTERY PRECAUTIONS]
Be sure to follow the correct polarity as indicated
in the battery compartment. Reversed batteries
may cause damage to the device.
•
Do not mix different types of batteries together
(e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
•
3)Replace the cover.
If the device is not to be used for a long period of
time, remove the batteries to prevent damage or
injury from possible battery leakage.
•
Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture.
•
- 11 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
Cables used here are commercially available.
[ANTENNA CONNECTION]
[CATV/SATELLITE CONNECTION]
75-ohm
Coaxial Cable
CATV Box or
Satellite Box *
VHF/UHF
VHF
VHF/UHF
Combiner
OR
OUT
IN
From Cable System or
Satellite Antenna
ANT.
A
U
D
I
O
O
U
T
COAXIAL
UHF
Flat twin-
lead cable
75-ohm
Coaxial Cable
OR
ANT.
OR
From Cable System
[Fig. 4]
VHF
or
UHF
Adaptor
*Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
Bent pin
NOTE:
Before plugging the antenna into the ANT. jack of the unit, check that the pin is
not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the
ANT. jack of the unit.
•
Cable
Plug
(Needs to be
straightened)
(Straight pin)
VHF/UHF COMBINED ANTENNA
A VHF UHF 75 ohm combination antenna can be
connected to ANT. jack of the unit.
CABLE WITH CONVERTER/DESCRAM-
BLER BOX OR SATELLITE BOX
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown above.
Channel selection must be made with the converter
box or satellite box. This means that channels cannot
be changed using the remote control of this unit.
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to the unit without a converter box.
NOTE:
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack
before moving the unit.
•
- 12 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO FRONT A/V INPUT JACKS
When you watch a program recorded on another source (VCR or video camera), use the
AUDIO/VIDEO input jacks on the front of the unit.
AUX
Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO
jacks of this unit.
K
L
Then press [SELECT] or [CH.
/
] until “AUX” appears on the screen.
POWER
SELECT
VOLUME
SKIP
PLAY
SKIP
STOP
OPEN/CLOSE
CHANNEL
REC/OTR
REW
PLAY
F.FWD
STOP/EJECT
HEADPHONE VIDEO
AUDIO
L
R
DVD
TV/VCR
SEARCH
ex.
VCR or video camera, etc.
To the Audio output jacks
Audio Cable
(commercially available)
(IN)
(OUT)
(OUT)
AUDIO
HEADPHONE VIDEO
L
R
To the Video output jack
[Front of the unit]
Video Cable
(commercially available)
(IN)
[Fig. 5]
NOTE:
When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the
monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R
channel equally.
•
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS (for DVD)
Use an audio coaxial digital cable (commercially available) for the audio connections.
Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
(OUT)
ANT.
AUDIO OUT
COAXIAL
ex.
MD deck, DAT deck, etc.
To AUDIO OUT
COAXIAL jack
(Only DVD AUDIO OUT)
To Coaxial digital
Audio input jack
Audio coaxial digital cable
(commercially available)
(IN)
[Fig. 6]
NOTES:
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner’s Manuals for the components to be connected to the unit.
Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-
tings may generate noise distortion and may also damage the speakers. (Refer to page 44.)
•
•
•
- 13 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a
DOLBY DIGITAL Data stream from its AUDIO OUT COAXIAL jack. By hooking the unit up to a Dolby
Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround
sound as enjoyed in movie theaters.
Use audio coaxial digital cables (commercially available) for the audio connections.
Center
speaker
(OUT)
Front speaker
(left)
Front speaker
(right)
ANT.
AUDIO OUT
COAXIAL
Dolby Digital
decoder
To AUDIO OUT
COAXIAL jack
(Only DVD AUDIO OUT)
To Coaxial digital
Audio input jack
Audio coaxial digital cable
(commercially available)
(IN)
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
[Fig. 7]
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner’s Manuals for the components to be connected to the unit.
If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the
setup mode. (Refer to page 44.)
•
•
•
Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the
setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the
speakers. (Refer to page 44.)
•
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
- 14 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TV/VCR SECTION
TV OPERATION AND SETTINGS
WATCHING A TV PROGRAM
DEGAUSSING
TV/VCR
This television has a degaussing circuit that will clear
up color errors on the TV screen that are caused by
any excess magnetism which happens to get too close
to the TV. This circuit is designed to operate once
when the set is first plugged in. If minor color
errors are seen in some locations on the screen,
please unplug the TV for approximately 30 min-
utes. When the TV is plugged back in, the degauss-
ing circuit will operate once to clear them up. Repeat
this procedure any time the TV screen is accidentally
magnetized or when the TV is moved or relocated.
TV/VCR
1 Plug in the unit power cord
Plug the unit power cord into a standard
AC outlet.
NOTE:
If any digits appear in the corner of the
•
screen, hit [POWER] without unplug-
ging the power cord.
2 Turn on the unit
Hit [POWER] to turn on the unit.
PICTURE CONTROL
TV/VCR
3 Select the channel number
The unit’s picture controls – BRIGHT, CON-
TRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a more natural looking image.
Press [CH. K / L] or the Number buttons to select
your desired channel number.
Notes for using the Number buttons:
¡You must precede single-digit channel numbers
with a zero (for example: 02, 03, 04 and so on).
¡When selecting cable channels which are higher
than 99, hit [+100] first, then press the last two
digits. (Example: to select channel 125, first hit
[+100] then hit [2] and [5].)
Make sure ...
The unit must be turned on.
•
1 Call up the menu
Hit [PICTURE].
4 Adjust sound
Press [VOL. X / Y] to adjust the
volume.
2 Select item you want to adjust
Press [K / L] until desired control is displayed.
VOLUME 20
Hit [MUTE] to instantly mute the
sound.
Hit it again to restore the previous sound level.
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
BRIGHT
CONTRAST
COLOR
NOTE:
BRIGHT
TINT
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
If you press [CH. K / L] in the DVD mode, you
can change the TV channels. Even if you turn off
the unit in the DVD mode, when you turn it on
again, it will go into the TV/VCR mode.
•
SHARPNESS
3 Adjust the setting
Press
[s
/
B]
to adjust to your desired level within 5
seconds.
TO WATCH CABLE OR SATELLITE
CHANNEL
If the unit is connected to a cable box or satellite
box, press [CH. K / L] to select CH3 or CH4
according to the output channel setting of the
device, and select desired channel on that device.
s
to decrease
brightness
to decrease
contrast
B
BRIGHT
to increase
brightness
to increase
contrast
•
CONTRAST
COLOR
TINT
to pale
to brilliant
TO WATCH EXTERNAL INPUT
When an external equipment is connected to the
front AUDIO/VIDEO input jacks, press
[SELECT] or [CH. K / L] repeatedly until
“AUX” appears on the screen.
to purple
to green
to clear
SHARPNESS to soft
•
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
•
- 15 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
If the unit displays a black box
on the TV screen, this means that
the unit is set to the TEXT mode.
To clear screen, select [CAP-
TION1], [CAPTION2] or [OFF].
•
SLEEP TIMER
TV/VCR
The Sleep Timer function turns off the unit without
using [POWER] after a desired period of time.
NOTE:
Make sure ...
The unit must be turned on.
•
This function does not work during the record-
•
ing mode.
1 Select “CAPTION”
- TV/VCR SETUP -
Hit [SETUP].
1 Call up the Sleep Timer Setting
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Press [K / L] to point to “CAP-
TION”.
Hit [SLEEP] so that “SLEEP 0 MINUTE” appears.
B
TIME SEARCH
INDEX SEARCH
2 Set sleep time
Hit [SLEEP] repeatedly until your
desired sleep time appears.
2 Select your desired caption mode
Each additional press will increase
the time by 30 minutes up to 120
minutes.
After 5 seconds, the Sleep Timer setting will disap-
pear automatically.
- TV/VCR SETUP -
Hit [ENTER] repeatedly until your
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
SLEEP 120 MINUTE
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
ZERO RETURN
B
TIME SEARCH
INDEX SEARCH
TO CANCEL THE SLEEP TIMER
Hit [SLEEP] to call up the Sleep Timer Setting. Hit
[SLEEP] repeatedly until “SLEEP 0 MINUTE”
appears.
3 Exit the caption setting mode
Hit [SETUP] to exit the menu.
NOTE:
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
•
CLOSED CAPTION SYSTEM
TV/VCR
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps 1 to 2 and select [OFF] using
You can view specially labeled (cc) TV programs,
movies, news and pre-recorded tapes with either a
dialogue caption or text display.
CAPTION mode: You can watch dramas, movies and
news while captioning the dialogues and the contents
of news.
[ENTER]. Then hit [SETUP] to return to TV mode.
TEXT mode: You can watch half screen text informa-
tion if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is
usually used for a second language if available.
NOTES:
Not all programs are broadcast with closed cap-
•
tions. Your unit is designed to provide error free
closed captions from high quality antenna, cable
and VCR signals. Conversely, poor quality signals
are likely to result in caption errors or no captions
at all. Common signal conditions which may cause
caption errors are listed below:
Automobile ignition noise
Electric motor brush noise
Weak snowy reception on TV screen
Multiplex signal reception displaying picture
•
•
•
•
ghosts or airplane flutter.
Playback of poorly recorded or worn VCR tapes.
•
- 16 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDING/DELETING CHANNELS
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
CHANNEL SET UP
TV/VCR
Make sure ...
The unit must be turned on.
•
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
1 Select “CHANNEL SET UP”
AUTO CHANNEL PROGRAMMING
Hit [SETUP].
B
Press [K / L] to point to “CHAN-
NEL SET UP”, then hit [ENTER].
As the initial setting, this unit has memorized all
channels, including the ones not available in your
area. This feature automatically puts only available
channels into the memory.
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
2 Select “ADD/DELETE CH”
Press [K / L] to point to
“ADD/DELETE CH”, then hit
[ENTER].
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
1 Select “CHANNEL SET UP”
B
ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
Hit [SETUP].
B
Press [K / L] to point to
“CHANNEL SET UP”, then hit
[ENTER].
TIME SEARCH
INDEX SEARCH
3 Enter the desired channel number
Press [CH. K / L] or the Number
buttons until your desired channel
number appears. (You can also
press [K / L] to enter it.)
2 Begin channel scanning
Press [K / L] to point to “AUTO
CH PROGRAMMING”, then hit
[ENTER].
The tuner scans and memorizes all
the active channels in your area.
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
08
B
ADD / DELETE
You must precede single-digit
channel numbers with a zero
•
(Example: CH8)
(Example: 02 ... 09).
When selecting cable channels which are higher
than 99, hit [+100] first, then press the last two
digits. (Example: to select channel 125, first hit
[+100] then hit [2] and [5].)
3 After scanning
•
The tuner stops on the lowest memorized channel.
NOTES:
When “AUTO CH PROGRAM-
MING” is activated where there
is no TV signal input, “NO TV
SIGNALS” will appear on the
display after the completion of
channel scanning.
•
NO TV SIGNALS
4 Delete (or add) it from (or into) memory
Hit [ENTER]. The channel number changes to light
red. The channel is deleted from memory.
To delete another channel, repeat steps 3 to 4.
If you hit [ENTER] again, the channel is memo-
rized again.
•
•
The unit may recognize CATV channels to be TV
•
channels if reception condition is poor. In this case,
check the antenna connection and try “AUTO CH
PROGRAMMING” again when reception condi-
tions are better.
Added channel : Light blue
Deleted channel : Light red
Channel memory programming is NOT neces-
•
sary when connected to a cable box or satellite
box. Just select the channel for cable box or
satellite input (ex. CH3) on the unit, then select
your desired channel on the cable box or satel-
lite box.
5 Exit the channel setup mode
Hit [SETUP] to exit the menu.
NOTE:
To confirm that channel(s) has been deleted or
added, press [CH. K / L].
•
- 17 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOCK SET UP
5 Select the year
Press [K / L] until your desired
year appears.
(Example: “2005”)
Then hit [B].
– MANUAL CLOCK SET –
(AUTO / MANUAL)
MONTH DAY
YEAR
2 0 0 5
0 5
/
:
0 6 FRI
TV/VCR
HOUR
– –
MINUTE
– – – –
The unit clock must be set correctly so that VCR
timer recording is possible. It is suggested that the
clock be set manually when first setting up the unit,
then set to [ON] the auto clock setting which will
periodically correct the setting if necessary.
NOTE:
If you cannot receive a station with time signals,
auto clock setting cannot be performed. Use manu-
al setting only.
6 Select the hour
Press [K / L] until your desired
hour appears.
(Example: “5”, “PM”)
Then hit [B].
– MANUAL CLOCK SET –
MONTH DAY
YEAR
2 0 0 5
0 5
/
:
0 6 FRI
•
HOUR
0 5
MINUTE
– – PM
MANUAL CLOCK SETTING
7 Select the minute
Press [K / L] until the
desired minute appears.
(Example: “40”)
Make sure ...
– MANUAL CLOCK SET –
MONTH DAY YEAR
The unit must be turned on.
In the example below, the clock is to be set to:
•
0 5
/
0 6 FRI
2 0 0 5
HOUR
0 5
MINUTE
4 0 PM
DATE
May 6th, 2005
:
SETTING TIME
5:40PM
1 Select “SETTING CLOCK”
Hit [SETUP].
Press [K / L] to point to “SET-
TING CLOCK”, then hit
[ENTER].
8 Start the clock
- TV/VCR SETUP -
5:40 PM
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Hit [SETUP].
B
Although seconds are not dis-
played, they begin counting from
00 when you hit [SETUP]. Use this
feature to synchronize the clock
with the correct time.
TIME SEARCH
INDEX SEARCH
NOTE:
2 Select “MANUAL CLOCK SET”
Press [K / L] to point to “MANU-
AL CLOCK SET”, then hit
[ENTER].
When unplugging the AC cord or if there is a
power failure for more than 3 seconds, you may
have to reset the clock.
•
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
B
[OFF]
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps 1 to 2.
2)Select the item you want to change using [B] .
3)Enter correct numbers using [K / L].
4)Hit [SETUP] to start the clock.
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
hit [ENTER] to turn [OFF] this function before
this step.
•
3 Select the month
– MANUAL CLOCK SET –
Press [K / L] until your desired
month appears.
MONTH DAY
YEAR
0 5
/
:
– – – – – – – – –
(Example: May → “05”)
Then hit [B]. (Or hit [s] to go
back one step.)
HOUR
– –
MINUTE
– – – –
4 Select the day
Press [K / L] until your desired day
appears.
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5
/
0 6 – – – – – – –
(Example: 6th → “06”)
Then hit [B].
HOUR
– –
MINUTE
– – – –
:
- 18 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC CLOCK SETTING
4 Enter the channel number that contains the
Automatic Clock Setting Signal
Hit [RETURN] to go back to “SETTING CLOCK”
menu.
Make sure ...
The unit must be turned on.
Confirm the unit is receiving a RF (Radio
Frequency) signal from either an antenna or cable
•
•
– SETTING CLOCK –
Hit [L] to select “AUTO CLOCK
system connection using the ANT. jack on the rear
of the unit.
NOTES:
AUTO CLOCK
[ON]
CH”.
AUTO CLOCK CH SEARCH
B
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[
45]
Press [s / B] until you locate Auto
[OFF]
If a cable converter box is being used, make sure it
is powered on.
•
Clock Set station number.
You must use the remote control to perform the
clock setting procedure.
If the unit is connected directly to a cable converter Hit [SETUP] to exit the menu.
box or satellite box, the local PBS station must be
selected on the cable box itself and the unit must
be set to the output channel of the cable converter
box or satellite box (usually channel 3 or 4), to be
able to set up or correct the clock automatically.
•
5 Exit the setting clock mode
•
NOTE:
Once the unit is turned off, it will periodically
check and set the correct date and time.
•
DAYLIGHT-SAVING TIME
1 Select “SETTING CLOCK”
- TV/VCR SETUP -
TV/VCR
Hit [SETUP].
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B
Select this feature and the unit’s clock automatically
will advance one hour in April, then reverse one hour
in October.
Press [K / L] to select
“SETTING CLOCK”, then hit
[ENTER] .
TIME SEARCH
INDEX SEARCH
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
First Sunday of April : At 2 AM the clock imme-
•
– SETTING CLOCK –
2 Set “AUTO CLOCK” to [ON]
Hit [ENTER] to select [ON].
B
AUTO CLOCK
[ON]
diately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
[OFF]
•
Make sure ...
3 Begin “AUTO CLOCK CH SEARCH”
The unit must be turned on.
•
Hit [L] to select “AUTO CLOCK
CH SEARCH”.
– SETTING CLOCK –
AUTO CLOCK
[ON]
B
AUTO CLOCK CH SEARCH
- TV/VCR SETUP -
TIMER PROGRAMMING
1 Select “SETTING CLOCK”
Hit [SETUP].
Press [K / L] to point to “SETTING
CLOCK”, then hit [ENTER].
Then hit [ENTER].
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
The unit begins searching for the
•
[OFF]
station which contains the auto
clock set signal. The search for a
TIME SEARCH
INDEX SEARCH
signal may take up to 20 seconds per channel.
– AUTO CLOCK CH SEARCH –
When the search has ended, “_
_” appears at the lower left of the
screen.
•
•
•
08
10
13
2 Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press [K / L] to point to “D.S.T.”,
then hit [ENTER] until [ON]
appears.
– SETTING CLOCK –
Write down the number(s) that
appear on the screen. They are
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
_ _
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
the auto clock station(s) in your area.
If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 18.
B
[ON]
3 Exit the Daylight-Saving Time mode
Hit [SETUP] to exit the menu.
NOTE:
During AUTO CLOCK CH SEARCH, the picture
may be distorted.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps 1 to 2 and select [OFF] using
[ENTER].
•
- 19 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
V-CHIP SET UP
When you select a rating and set
•
it to [BLOCK], the higher ratings
will be blocked automatically.
The lower ratings will be avail-
able for viewing.
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
TV/VCR
(
)
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
This feature enables parents to prevent their children
from watching inappropriate material on TV. When
you try to access a program which is blocked,
“PROTECTED PROGRAM by ...” message appears
on the TV screen.
When you set the lowest rating to
[VIEW], all other ratings will automatically be
available for viewing.
•
V-CHIP SET UP
5 Setting “Sub-Ratings”
Make sure ...
TV–Y
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
When you select the ratings of TV-
B
TV–Y7
TV–G
(
)
The unit must be turned on.
•
Y7, TV-PG, TV-14 or TV-MA you
will have the option of setting sub
rating categories.
Press [K / L] to select a rating with
sub-ratings you wish to block, then
hit [ENTER] twice.
Press [K / L] to select a sub-rating,
then hit [ENTER] to set it to
[BLOCK] or [VIEW].
TV–PG (
)
)
)
TV–14
(
TV–MA(
1 Select “V-CHIP SET UP”
Hit [SETUP].
Press [K / L] to select “V-CHIP
SET UP”, then hit [ENTER].
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
TV–Y7
FV
[BLOCK]
[BLOCK]
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B
INDEX SEARCH
2 Enter Access code
Press the Number buttons to enter
the access code.
TV–PG
[BLOCK]
B
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
ACCESS CODE
_
_
_
_
For the first time set-up or in the
event the unit has lost power,
enter the default code of 0000.
•
Selection
TV-Y7
FV
Rating Category Explanations
Fantasy Violence
3 Select the desired item
TV-PG, TV-14, TV-MA
Press [K / L] to select “TV RATING”, “MPAA RAT-
ING” or “CHANGE CODE”, then hit [ENTER].
Refer to the pages below to set up each item.
– V-CHIP SET UP –
D
L
S
Suggestive Dialog (TV-PG, TV-14 only)
Coarse Language
Sexual Situation
Violence
A
P 20 Step
4
4
4
B TV RATING
MPAA RATING
CHANGE CODE
V
B
P 21 Step
NOTE:
The blocked sub-ratings will
appear next to the rating category
in the “TV RATING” menu.
C
P 21 Step
•
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
(
)
[VIEW]
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
A
TV RATING SET UP
Follow steps to in the “V-CHIP SET UP” sec-
1
3
tion above.
6 Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
4 Blocking TV programs
Press [K / L] to select a rating that
you wish to block.
Hit [ENTER] repeatedly to set it to
[BLOCK] or [VIEW].
B
TV–Y
TV–Y7
TV–G
TV–PG (
TV–14
TV–MA(
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
NOTE:
(
)
)
)
)
To change the rating, the TV must
•
(
PROTECTED PROGRAM
by TV-Y
be turned to an unprotected pro-
gram. If “PROTECTED PRO-
GRAM by ...” appears on the
screen, please change the channel
to a station that is not protected.
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
TV-Y7
TV-G
Appropriate for children seven and older
General Audience
TV-PG
TV-14
Parental Guidance suggested.
Unsuitable for children under 14
TV-MA Mature audience only
- 20 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
B
MENU LANGUAGE
MPAA RATING SET UP
TV/VCR
Follow steps to in the “V-CHIP SET UP” section
on page 20.
1
3
1 Select “LANGUAGE”
Hit [SETUP].
Press [K / L] to point to “LAN-
GUAGE”.
- TV/VCR SETUP -
4 Select your desired item
Press [K / L] to point to your
desired item, then hit [ENTER] to
select [BLOCK] or [VIEW].
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
G
[VIEW]
PG
[VIEW]
PG–13
R
NC–17
X
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
B
TIME SEARCH
INDEX SEARCH
Selection
G
PG
PG-13
R
Rating Category Explanations
General Audience
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompa-
nying parent or adult guardian
No one under 17 admitted
2 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”
Hit [ENTER] repeatedly to select “ENGLISH”,
“ESPAÑOL”= Spanish or “FRANÇAIS”= French.
3 Exit the Language mode
Hit [SETUP] to exit the menu.
NOTES:
NC-17
X
Mature audience only
This function effects only the language on the
screen menu and not the audio source.
•
When you select a rating and set it to [BLOCK],
the higher ratings will be blocked automatically.
The lower ratings will be available for viewing.
When you set the lowest rating to [VIEW], all
other ratings will automatically be available for
viewing.
•
•
If for some reason the menu is in Spanish or
•
French, hit [SETUP], press [K / L] to point to
“IDIOMA [ESPAÑOL]” or “LANGAGE
[FRANÇAIS]”, then hit [ENTER] repeatedly to
select desired language, then hit [SETUP].
5 Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
C
CHANGE ACCESS CODE
Follow steps to in the “V-CHIP SET UP” sec-
1
3
tion on page 20.
4 Enter New code
NEW CODE
X X X X
Press the Number buttons to enter
your desired access code in the
“NEW CODE” space, then enter
the same code in the “CONFIRM
CONFIRM CODE
_
_
_
_
CODE” space. When completed, the menu will
return to “V-CHIP SET UP”.
Make sure you enter exactly the same new code in
the “CONFIRM CODE” space as one in the
“NEW CODE” space. If they are different, the
“NEW CODE” space is cleared for redoing.
•
5 Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
NOTE:
Your personal access code will be erased and will
•
return to the default (0000) when a power failure
occurs or when you turn off the power using a
wall switch. If you have forgotten the code, unplug
the power cord for 10 seconds to restore the access
code to 0000.
- 21 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
MTS (Multi-Channel Television sound) SYSTEM
You can record or listen to a program in MTS stereo.
CHECKING THE SELECTED MTS MODE
TV/VCR
By hitting [DISPLAY], the status shown below will
1) When a program is broadcast in stereo,
“STEREO” appears on the TV screen.
appear on the display when you play a VHS tape or
receive a broadcast on the unit tuner channel you are
watching.
2) When a program is broadcast in second audio,
“SAP” appears on the TV screen.
3) When a program broadcast both in stereo and sec-
ond audio, “STEREO” and “SAP” appear on the
TV screen.
PLAY
HIFI
B
12:00AM
CH 123
4)
STEREO/SAP
3)
2)
1)
NOTE:
Although a program may be broadcast in both
•
stereo and second audio, you cannot record in
both stereo and second audio at the same time.
4) While the unit is set in HIFI stereo mode and
playback mode, “HIFI” appears on the TV screen.
While the unit is set in monaural (“MONO”)
mode, “HIFI” disappears from the TV screen.
NOTE:
SP
COUNT
0:00:00
Second Audio Program, which means your
program, can also be received in a second
language or sometimes a radio station.
SAP
High Fidelity which produces better sound
than standard stereo units.
HIFI
If you play non-HIFI tapes while the unit is set
•
in “HIFI”, “HIFI” will disappear from the TV
screen and the unit will play automatically in
monaural.
MTS RECORDING/MONITOR MODE
TV/VCR
Type of broadcast Display on
STEREO/SAP
Hi-Fi audio track (2-channel) Normal audio
the TV screen SELECTION
L-channel
R-channel
track
Regular
-None-
-Invalid-
Mono
Mono
Mono
(monaural audio)
Stereo broadcast
Bilingual broadcast
STEREO
SAP
-Invalid-
STEREO*
L
R
L+R
Main audio
program
Main audio
program
Main audio
program
SAP*
Sub audio
program
Sub audio
program
Sub audio
program
Stereo & Bilingual
broadcast
STEREO
SAP
STEREO*
SAP*
L
R
L+R
sub audio
program
sub audio
program
sub audio
program
*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
- 22 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING THE MTS SYSTEM
TV/VCR
You can select the MTS output mode for recording or
watching the program, also the audio output mode
for playing cassettes.
WHEN IN THE EXTERNAL INPUT
MODE (“AUX”)
Hitting [AUDIO] does not affect the audio output
mode and the current audio output mode does not
appear on the TV screen.
WHEN RECEIVING AN MTS BROADCAST
Hit [AUDIO] repeatedly to select the MTS output
mode.
The output mode changes as described below every
time you hit the button.
•
STEREO
SAP
MONO
The current mode appears on the TV screen for
about 5 seconds.
•
NOTES:
The initial setting is “STEREO”. The unit records
automatically MTS broadcasts in HIFI stereo sound
unless you select SAP mode recording beforehand.
•
This setting is saved even if the unit is turned off
or the AC cord is unplugged.
•
If you select second audio when second audio is
not available, the unit will record normal audio.
•
WHEN PLAYING CASSETTES
Hit [AUDIO] to select “HIFI” or “MONO”.
The current mode appears on the TV screen for
about 5 seconds.
•
The initial setting is “HIFI”.
This setting is saved until the cassette is ejected.
•
•
NOTES:
Normally “HIFI” should be selected for playback
with HIFI sound.
•
When you play non-HIFI tapes, the unit will play
only in the monaural mode even if you set HIFI.
•
- 23 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CASSETTE
This unit will operate with any cassette that has the
mark. For best results, we recommend the use of
high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
INSERTING A CASSETTE
Avoid moisture. Moisture condensation may occur
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the unit. The unit will
automatically turn on.
•
on the tape if it is moved from a cold place to a
warm place or vice versa. Before using a tape with
these conditions, to avoid damage of the tape and
your unit, wait until the tape has warmed to room
temperature and the moisture has evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
•
Window
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
•
•
WRONG
CORRECT
TWO DIFFERENT TAPE SPEEDS
REMOVING A CASSETTE
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/play-
back time using T60, T120 or T160 tapes in each
mode.
1)In the stop mode, hit [STOP/EJECT
P
N] on the
unit. The cassette will be ejected.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
Tape Speed
Type of tape
SP mode
Recording/Playback Time
T60
1 hour
3 hours
T120
T160
2 hours 2-2/3 hours
6 hours 8 hours
SLP mode
ERASE PREVENTION
NOTE:
You can play back a tape recorded in LP mode
(Long Play).
•
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
If you decide to record on
the tape again, cover the
hole with plastic tape.
Plastic Tape
NOTE:
In DVD mode, whether the cassette is with tab or
without tab you insert, it doesn’t start playing until
•
[PLAY O]
you hit
.
In TV/VCR mode, if the cassette without tab is
inserted, playback will automatically start.
- 24 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
NORMAL PLAYBACK
SLOW MOTION
TV/VCR
TV/VCR
Hit [PAUSE F], then hit [D] to start the playback
in slow motion. The unit mutes the sound during
slow motion. Hit [PLAY O] to return to normal
playback.
Make sure ...
The unit must be turned on.
•
1 Insert a prerecorded tape
If the erase-prevention tab has been removed, the
unit will start playback automatically.
NOTE:
If it is left in the slow mode for more than 5 min-
utes, the unit will automatically go into the stop
mode.
•
B
PLAY
2 To begin playback
Hit [PLAY O].
STILL PICTURE
TV/VCR
You can view a still picture on the TV screen during
playback (the still mode). Hit [PAUSE F] during
playback. Only tapes recorded in the SLP mode will
show the least amount of lines. Hit [PLAY O] to
return to playback.
3 To stop playback
Hit [STOP C].
STOP
NOTES:
You can advance the picture one frame at a time by
hitting [PAUSE F] during the still mode.
If it is left in the pause mode for more than 5 min-
utes, the unit will automatically switch to the stop
mode.
•
NOTES:
•
Even in the DVD mode, you can start the VCR
playback if you hit [PLAY ] (of the TV/VCR
side).
•
O
VCR playback will stop and the mode will change
•
VERTICAL HOLD CONTROL
to the DVD mode by pressing [SELECT],
O
N
[PLAY ] (DVD side) or [OPEN/CLOSE ].
TV/VCR
In the pause/still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
[CH. K / L].
TRACKING ADJUSTMENT
TV/VCR
NOTE:
Tracking adjustment will be set automatically
(Digital Tracking function) when you start play-
back.
If there are video noise lines on the screen, refer to
TRACKING ADJUSTMENT on this page.
•
•
•
Noise lines (black and white streaks) may appear
on the playback picture when playing pre-recorded
tapes or tapes recorded on other VCR. If this
occurs, press [CH. K / L] until the streaks disap-
pear.
You can reduce the noise lines by pressing
[CH. K / L] in the slow mode too. Tracking
adjustment in the slow mode will not be set auto-
matically.
To return to the Digital Auto Tracking function,
stop the tape once and start playback.
•
•
- 25 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL PLAYBACK
Make sure ...
AUTO REPEAT PLAYBACK
The unit must be turned on.
•
Insert a prerecorded tape.
•
TV/VCR
The unit has the auto repeat function that allows you to
repeat a tape indefinitely without hitting [PLAY O].
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the begin-
ning to a blank part, which is blank for more than
10 seconds.
RENTAL PLAYBACK
TV/VCR
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1 Select “USER’S SET UP”
- TV/VCR SETUP -
1 Select “USER’S SET UP”
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
Hit [SETUP].
TIMER PROGRAMMING
CHANNEL SET UP
SETTING CLOCK
Hit [SETUP].
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
CHANNEL SET UP
Press [K / L] to point to “USER’S
SET UP”, then hit [ENTER].
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press [K / L] to point to “USER’S
SET UP”, then hit [ENTER].
INDEX SEARCH
INDEX SEARCH
USER’S SET UP
–
–
2 Set “RENTAL” to [ON]
Press [K / L] to point to
“RENTAL”.
2 Select “ALL” or “BLANK”
Press [K / L] to point to “REPEAT
PLAY”.
Hit [ENTER] repeatedly until your
desired selection [ALL] or
[BLANK] appears.
USER’S SET UP
–
–
B
RENTAL
[ON]
[OFF]
[OFF]
REPEAT PLAY
AUTO RETURN
RENTAL
[OFF]
[ALL]
[OFF]
B
REPEAT PLAY
AUTO RETURN
Hit [ENTER] until [ON] appears.
3 Exit the Rental setting
Hit [SETUP] to return to the TV mode.
3 Exit the Repeat Play setting
Hit [SETUP] to return to the TV mode.
4 Start playback
Hit [PLAY O] to start playback.
“RENTAL PLAY B” appears.
4 Start playback
Hit [PLAY O] to start the Repeat Play.
“REPEAT PLAY B” appears.
Once you select the rental mode, it stays in effect
even after you turn off the unit.
•
Once you select the repeat play mode, it stays in
effect even after you turn off the unit.
If the rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
•
•
TO CANCEL THE RENTAL MODE
Repeat steps 1 to 2 and select [OFF] using
[ENTER]. Hit [SETUP] to return to TV mode.
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps 1 to 2 and select [OFF] using
[ENTER]. Hit [SETUP] to return to TV mode.
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
- 26 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SEARCH
Make sure ...
NOTE:
Tapes recorded in the SP or LP mode will normally
•
The unit must be turned on.
•
display a noise bar on the TV screen and the pic-
ture may revert to Black and White.
Insert a tape.
•
ZERO RETURN
3 Return to normal speed
Hit [PLAY O].
TV/VCR
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
TIME SEARCH
Zero Return WILL NOT work on a blank tape or
•
TV/VCR
a blank portion of a tape.
The Time Search function makes it possible to quick-
ly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
1 Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
NOTE:
Time Search can be set up to a maximum of 9
•
hours 50 minutes (9:50) by 10 minutes at a time.
In the example below: To watch a program before/
after 2 hour 50 minutes from the present position, in
either direction.
2 Reset the counter to 0:00:00
Hit [C.RESET] repeatedly.
3 Begin recording or playback
Press [RECORD] or [PLAY O].
Hit [STOP C] when recording or playback is com-
pleted.
- TV/VCR SETUP -
1 Select “TIME SEARCH”
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
Hit [SETUP].
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
Press [K / L] to point to “TIME
SEARCH”, then hit [ENTER].
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
B
4 To activate “ZERO RETURN”
Hit [SETUP].
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Press [K / L] to point to “ZERO
RETURN”, then hit [ENTER].
The unit will begin rewinding and
the counter will appear on the TV
screen.
2 Enter your desired time
Press [K / L] until your desired time
appears. (Example: “2:50” stands for
2 hours 50 minutes)
TIME SEARCH
2 : 50
B
TIME SEARCH
INDEX SEARCH
If you wish to cancel the Time
Search at this point, hit [SETUP].
The tape will automatically stop when the counter
returns to 0:00:00 (approx.).
3 Begin Time Search
By pressing [s B], the unit will rewind or fast for-
/
PICTURE SEARCH
ward to the specified point.
The time counts down during the search. When the
display shows “0:00”, the tape will start playback
automatically.
TV/VCR
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
TO CANCEL DURING TIME SEARCH
Press [STOP/EJECT
P
N] on the unit or
[STOP
C].
1 Start Picture Search
During playback, press [D] or [E] to view at a
high speed (in forward/reverse).
This will delete the selected time.
2 Change searching speed
Press [D] or [E] again to view at super high
speed (in the LP/SLP modes only).
- 27 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
- TV/VCR SETUP -
INDEX SEARCH
1 Select “INDEX SEARCH”
Hit [SETUP].
Press [K / L] to point to “INDEX
SEARCH”, then hit [ENTER].
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TV/VCR
This feature provides a method of indexing the start-
ing point so that it can be easily returned to in either
fast forward or rewind mode.
TIME SEARCH
INDEX SEARCH
B
The index mark will be made automatically when
[RECORD] is hit. It will also be marked at the
starting point of Timer recording and OTR.
The index mark will not be recorded if [PAUSE F]
is hit and released during recording.
The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 min-
utes for SLP recording.
•
INDEX SEARCH
0 3
2 Enter your desired number
Press [K / L] until the number of
programs that you want to skip
appears.
•
(Example: “03” for 3 programs)
•
The Index Search mode will be canceled if the pro-
cedures are not activated in 30 seconds.
•
In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number 7. You
must skip three programs.
•
3 Begin Index Search
Press [s B]. The unit begins rewinding or fast for-
/
warding to the beginning of desired program.
NOTE:
Every time an index signal is skipped, the number
in the program indicator decreases by one.
•
CURRENT PLAYBACK PROGRAM
Beginning of
the tape
End of
the tape
4 After Index Search
When the preset program is reached, the unit will
start playback automatically.
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7
4
3
2
1
1
2
3
A video cassette must be inserted in the unit for
this function to work.
•
INDEX MARK
The number of Index Searches can be set up to 20.
This function will not operate in the recording mode.
When you want to cancel the Index Search while
in progress, hit [STOP C].
•
•
•
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
TV/VCR
TV/VCR
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change on a blank tape or blank portions on the
tape.) The “–” indication will appear when the tape
has rewound further than “0:00:00” on the tape
counter.
When the end of a tape is reached during record-
ing, playback, or fast-forward, the tape will auto-
matically rewind to the beginning. After rewinding
finishes, the unit will eject the tape and turn itself
off.
This function is operative when Repeat Play is set
to the [OFF] position.
The tape will not auto-rewind during timer record-
ing or One Touch Recording.
•
•
•
- 28 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Make sure ...
The unit must be turned on.
Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
•
•
NOTES:
This unit will ONLY record and view the same channel.
This unit cannot record the contents from the built-in DVD.
•
•
SKIPPING UNWANTED
NORMAL RECORDING
SCENES DURING RECORDING
TV/VCR
TV/VCR
You can ONLY watch the same TV program that is
being recorded.
Hit [PAUSE F] to temporarily stop
recording.
PAUSE
Press [PAUSE F] or [RECORD]
to resume recording.
NOTES:
1 Select the channel to be recorded
Press the Number buttons or
SP
CH 10
[CH. K / L].
After 5 minutes, the unit will
•
automatically switch to the recording mode to pre-
vent tape damage.
NOTE:
If Closed Caption mode is on, the On-Screen
Display will appear for 5 seconds, then disappear.
•
If the unit is connected to a cable box or satellite
•
box, the unit must be on CH3 or CH4, then the
channel to be recorded must be selected on the
cable box or satellite box.
2 Select the tape speed
Hit [SPEED] to select the desired
tape speed (SP/ SLP).
SP
REC
3 Begin recording
Hit [RECORD].
SP
4 Stop recording
Hit [STOP C].
- 29 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Time(s)
1 time
Display
Recording length
(normal recording)
OTR (One Touch Recording)
2 times
3 times
0:30
1:00
30 minutes
60 minutes
TV/VCR
This function enables you to set a recording length
simply by hitting [REC/OTR] on the unit.
Make sure ...
17 times
8:00
480 minutes
The unit must be turned on.
Insert a cassette tape with its erase-prevention tab
in place. (If necessary, rewind or fast forward the
•
•
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
tape to the point at which you want to begin
recording.)
NOTES:
You cannot start OTR with the remote control.
Recording starts immediately when [REC/OTR]
is hit.
TV/VCR
You can make copies of video tapes made by friends
or relatives for your enjoyment.
•
•
You can not copy a DVD to a videotape.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
When [REC/OTR] is hit 18 times, the unit returns
•
to the normal recording mode.
To stop the OTR operation, hit [STOP P] on the
unit or on the remote control.
To show the remaining time, hit [DISPLAY] on
the remote control so that “OTR” appears on the
TV screen. (It will show up momentarily then dis-
appear.)
•
Connect your unit and a source (Playing) VCR using
the following diagram.
•
[Fig.8]
[This unit]
AUDIO
F.FWD
STOP/EJECT
HEADPHONE VIDEO
L
R
Recording stops when the display shows 0:00.
Please note that in the SLP mode maximum
recording time, assuming the tape is started at the
beginning, is 8 hours using T-160 (or 6 hours
using T-120).
•
•
If the tape runs out before the end time, the unit
will switch to the stop mode immediately, ejects
the tape and turns itself off.
Even if [POWER] is hit during OTR, the unit
continues recording.
•
[Ex: Source VCR or
camcorder]
AUDIO
L
Audio/Video
cable
•
OUT
IN
R
VIDEO
(not supplied)
OUT
IN
1 Select the channel to be recorded
Press the Number buttons or [CH. K / L].
NOTE:
1)Insert a pre-recorded video cassette into the source
VCR or camcorder.
2)Insert a blank video cassette or one you want to
record over, into the unit’s cassette compartment.
3)Hit [SPEED] on remote control for the unit to
select the desired recording speed (SP/SLP).
4)Press [CHANNEL K / L] on the unit until “AUX”
appears on the screen.
If the unit is connected to a cable box or satellite
•
box, the unit must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box
or satellite box.
5)Hit [REC/OTR] on the unit.
6)Begin playback of the tape in the source VCR or
camcorder.
2 Select the tape speed
Hit [SPEED] to select the desired tape speed
(SP/SLP).
NOTE:
For best results during copying, use the front
•
panel controls whenever possible. The remote
control might affect the source VCR’s playback
operation.
3 Begin OTR
Hit [REC/OTR] on the unit as
OTR (2 : 30)
many times as needed. The record-
ing length will be determined by
the number of times you hit
7)To stop copying, hit [STOP/EJECT
unit, then stop the tape on the source VCR or cam-
corder.
P
N] on the
[REC/OTR]. Each time it is hit,
the recording time will be increased
SP
by 30 minutes up to 8 hours.
- 30 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
AUTOMATIC TIMER
RECORDING
1 Select “TIMER PROGRAMMING”
- TV/VCR SETUP -
Hit [SETUP].
B
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Confirm “TIMER PROGRAM-
MING” is pointed by hitting [K],
then hit [ENTER].
TV/VCR
You may set the unit to start and end a recording
while you are away. You can set 8 programs to record
on specific days, daily or weekly within a 1 year
period.
TIME SEARCH
INDEX SEARCH
If you have not yet set the clock,
•
“MANUAL CLOCK SET” appears. If so, follow
steps 3 to 8 on page 18. Then set the timer record-
ing.
In the example below, the timer is being set to record:
DATE:
July 4th, 2005
SETTING TIME: from 7:30PM to 8:50PM
2 Select your desired program position (1 to 8)
CHANNEL:
TAPE SPEED:
CH61
SP
– TIMER PROGRAMMING –
Press [K / L] to select the desired
CH DATE
BEGIN END
program position, then hit [B].
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Make sure ...
B
If a cable box or satellite box is connected with the
unit you will be limited to record only one channel,
and the channel selector on the unit must be select-
ed to the output channel of the boxes CH 3 or CH
4 and then the actual channel to be recorded must
be selected on the boxes.
•
– TIMER PROGRAMMING –
CH DATE BEGIN END
3 Set the channel number
Press [K / L] until the desired
channel number appears (Example:
CH61), then hit [B].
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Clock must be set to the correct time and date
before setting the timer.
B
•
The unit must be turned on to program it.
Insert a cassette tape with its erase-prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
•
•
NOTE:
If the unit is connected to a cable box or satellite
box, the unit must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box
or satellite box.
•
The channel you want to record is properly set in
advance. (Refer to page 17.)
•
Avoid overlap of programs ...
There is a chance that a program will not be record-
ed, when programs overlap;
4 Select once, every day or weekly recording
For once recording :
– TIMER PROGRAMMING –
CH DATE BEGIN END
Hit [K] until the desired date
appears. (Example: “7/04” for
July 4th)
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 7/04 MON -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
The program with an earlier start has priority.
Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
•
•
B
When the starting time is the same, the program set
on the highest position in the program list has pri-
ority.
The illustration below demonstrates the sequence
of recordings.
Then hit [B].
•
For every day recording : To record a TV program
at the same time on the same channel every day.
(Example: Monday through Sunday)
•
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY DAY -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Hit [L] until “EVRY DAY”
appears, then hit [B].
Program 1
Program 2
Program 3
10:00AM - 11:00AM
9:00AM - 10:00AM
9:30AM - 12:00PM
B
For weekly recording : To record a TV program at
the same time on the same channel every week.
(Example: every Monday)
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
– TIMER PROGRAMMING –
Hit [L] until “EVRY” and your
desired day of the week appear
CH DATE
BEGIN END
9:30AM-12:00PM
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY MON -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
9:00AM
10:00AM
11:00AM
12:00PM
together, then hit [B].
*Recording period is SHADED
B
- 31 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
5 Set beginning hour
Press [K / L] until the desired hour
appears. (Example: “ 7, PM” for
7:30PM)
– TIMER PROGRAMMING –
CH DATE BEGIN END
The display will not be turned on automatically at
•
the time the programmed recording begins. To
watch the currently recorded TV program or to
play a DVD disc, hit [POWER] and [SELECT] to
choose the TV/VCR mode or the DVD mode.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 MON 7:12P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
Then hit [B].
If the tape runs out before the end time, the unit
will switch to the stop mode immediately and the
tape will be ejected.
•
– TIMER PROGRAMMING –
CH DATE BEGIN END
6 Set beginning minute
Press [K / L] until the desired
minute appears. (Example: “30”
for 7:30PM)
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 MON 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
TIMER PROGRAM EXTENSION
Then hit [B].
To shift the time schedule of an automatic timer
recording.
1)Hit [POWER].
2)Repeat step 1 on page 31.
3)Hit [RECORD] and select the desired program
using [K / L].
4)Hit [RECORD] again.
7 Set end hour
Press [K / L] until the desired hour
appears. (Example: “8, PM” for
8:50PM)
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:30PM- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 MON 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
Then hit [B].
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, hit [PAUSE F] on
the remote control. The recording time returns to
the original time.
– TIMER PROGRAMMING –
CH DATE BEGIN END
8 Set end minute
Press [K / L] until the desired
minute appears. (Example: “50”
for 8:50PM)
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PM- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 MON 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
Then hit [B].
NOTE:
9 Set the tape speed
Press [K / L] until the desired tape
speed appears. (Example: “SP”)
When you shift forward the time schedule during
recording, the recording speed will automatically
be set to the SLP mode.
•
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PMSP
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 MON 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
5)Press [ENTER] or [RETURN] to exit the setting
menu. Then hit [SETUP] to return to original
mode.
10 Finish setting the program
TO CORRECT A PROGRAM
Press [ENTER] or [RETURN] to complete setting.
While setting a program; hit [s] to go back one
step and enter the correct numbers using [K / L].
•
To set another program, repeat steps 2 to 10.
Hit [SETUP] to exit the menu.
•
•
After setting a program;
1)Hit [POWER].
•
11 Set the timer
Hit [POWER] to set automatic timer recording. The
recording indicator lights up.
2)Repeat steps 1 to 2 on page 31.
3)Hit [B] (or hit [s] to go back one step) until the
part you want to correct begins flashing, then
make the changes using [K / L].
You must turn off the unit to activate automatic
timer recording.
•
4)Hit [POWER] to set automatic timer recording.
If power is not turned off and you continue watch-
ing TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
1)Hit [POWER].
2)If recording is in progress, hit [STOP/EJECT
on the unit.
If the erase-prevention tab is removed, the cassette
will be ejected when [POWER] is hit to off.
•
P
N]
3)Repeat steps 1 to 2 on page 31 and select a pro-
gram you want to cancel.
4)Hit [C.RESET].
5)Hit [SETUP] to return to TV mode.
- 32 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CONFIRM THE TIMER SETTING
1)Hit [POWER] so that the Recording indicator light
goes off.
AUTO RETURN
TV/VCR
2)Hit [SETUP].
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
3)Confirm “TIMER PROGRAMMING” is selected.
4)Hit [ENTER]. The details of programs appear on
the TV screen.
5)Hit [SETUP] to return to TV mode.
1 Select “USER’S SET UP”
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
Hit [SETUP].
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press [K / L] to point to “USER’S
SET UP”, then hit [ENTER].
INDEX SEARCH
2 Set “AUTO RETURN” to [ON]
Press [K / L] to point to “AUTO
RETURN”, then hit [ENTER] until
[ON] appears.
USER’S SET UP
–
–
RENTAL
[OFF]
[OFF]
[ON]
REPEAT PLAY
AUTO RETURN
B
3 Auto Return will begin
When all the timer recordings are completed, the unit
will rewind to the beginning of the recorded pro-
gram(s).
NOTE:
If you hit [POWER] while tape is rewinding, the
Auto Return will stop.
•
4 Watch the recorded program
Hit [PLAY O].
TO CANCEL THE AUTO RETURN
MODE
Repeat steps 1 to 2 and select [OFF] using
[ENTER].
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
- 33 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, hit [DISPLAY]. Each time you hit [DIS-
PLAY], the TV screen will change as follows:
When the Closed Caption mode is OFF:
When the Closed Caption mode is ON:
Counter mode: After 5 seconds, only the counter
remains. To clear it, hit [DISPLAY].
Clock mode: After 5 seconds, only the clock and
the channel number remain. To clear them, hit
The On Screen Display disappear after 5 seconds.
This is true even if [MUTE] or [PAUSE F] is
pressed while recording.
•
•
•
•
[DISPLAY].
OFF mode
Clock/Counter mode
OFF mode Counter mode
Clock mode
STOP
STOP
5:40PM
CH2
STOP
5:40 PM
CH2
SP
COUNT 0:12:34
SP
SP
COUNT 0:12:34
After 5 seconds
After 5 seconds
5:40PM
CH2
COUNT 0:12:34
Counter
remains
Clock & Channel
remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
TV Display
5A
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
A
B
14
15
CATV channel
TV Display
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CATV channel
R
S
T
U
V
W
W+1
37
W+2
38
W+3
39
W+4
40
W+5
41
W+6
42
W+7
43
W+8
44
W+9
45
TV Display
31
32
33
34
35
36
CATV channel
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display
CATV channel
TV Display
CATV channel
TV Display
76
W+55 W+56 W+57 W+58
91 92 93 94
77
78
79
80
81
82
83
84
85
W+59 W+60 W+61 W+62 W+63 W+64
100 101 102 103 104 105
86
87
88
89
90
A-5
95
A-4
96
A-3
97
A-2
98
A-1
99
CATV channel
TV Display
CATV channel
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
TV Display
106
W+80 W+81 W+82 W+83 W+84
121 122 123 124 125
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CATV channel
TV Display
- 34 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
Recorded
Playable
discs
Disc size
Region code
Disc types
Mark (logo)
signals
DVD-Video
or
* 1,2,4,6,10,11
Example
12 cm
or
8 cm
Title 1
Title 2
DVD-RW
DVD-R
Digital video
(MPEG2)
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1
Chapter 2
-
-
-
* 1,3,4,5,6
7,9,10
DVD+RW
DVD+R
* 1,3,4,5,6,8,9,10
Audio CD
* 4,6,10
Audio CD
Example
12 cm
or
8 cm
Digital audio
Track 1
Track 2
Track 5
Track 6
Track 3
Track 4
CD-RW
CD-R
* 4,5,6,9,10
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot
be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*3: Discs recorded in the VR (Video Recording) format cannot be played back.
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the
recorder or special properties of discs.
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not
play them back. Even if they are played back, the sound or video quality will be compromised.
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD
recorder. However, depending on the recording status of a disc, the disc may not be played back at all or
normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with
the DVD recorder. Refer to the manual accompanying the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be
played back at all or normally (the picture or sound may not be smooth, etc.).
*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not
play back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-
mat can only be played back on unit with the same region code.
UNPLAYABLE DISCS
¡
NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3
On the following disc, the sound MAY NOT be heard.
¡
Super Audio CD
NOTE: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
Any other discs without compatibility indications
¡
- 35 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A DISC
BASIC PLAYBACK
GENERAL FEATURES
DVD-V CD
DVD-V
VD may contain menus to navigate the disc and
D
Getting started
access special features. Press the appropriate
Number buttons or [K / L / s / B] to highlight
your selection in the DVD main menu and hit
[ENTER] to confirm.
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1
Hit [POWER].
¡The power will turn on.
NOTES:
¡Select DVD mode by hitting [SELECT], then oper-
ate the DVD functions.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
2
3
Hit [OPEN/CLOSE N] to open disc loading
tray.
Place the chosen disc in the tray, with the
label facing up.
DISC MENU
DVD-V
1
Hit [DISC MENU].
¡The DVD main menu will appear.
¡If the feature is not available,
appear on the TV screen.
¡If disc menu is available on the disc, audio lan-
guage, subtitle options, chapters for the title and
other options will appear for selection.
4
Hit [PLAY O].
symbol may
¡The tray will close automatically and playback will
then start from the first chapter or track of the disc.
¡Closing the disc tray manually or by hitting
[OPEN/CLOSE N] also starts playback.
¡If the playback does not start automatically, hit
[PLAY O].
2
Press [K / L / s / B] to select an item and
hit [ENTER] to confirm selection.
¡When you playback a DVD which features a title
menu, it may appear on the screen. In this case,
refer to “TITLE MENU” on this page.
TITLE MENU
5
Hit [STOP C] to stop playback.
DVD-V
1
Hit [TITLE].
NOTES:
¡The title menu will appear.
¡If the feature is not available,
appear on the TV screen.
¡When the DVD mode has been switched to the
TV/VCR mode, the DVD mode shuts down first and
then the TV picture and sound appears in about 4 sec-
onds. Similarly, when [POWER] is hit to turn off in
the DVD mode, this mode shuts down first and then
the unit is turned off.
symbol may
2
Press [K / L / s / B] to select an item, and
hit [ENTER] to confirm selection.
CALLING UP A MENU SCREEN
¡A “prohibited icon” may appear at
DURING PLAYBACK
the top-right on the TV screen dur-
ing operation, warning that a pro-
hibited operation has been encoun-
tered by the DVD or the disc.
¡Hit [DISC MENU] to call up the DVD menu.
¡Hit [TITLE] to call up the title menu.
NOTE:
¡Contents of menu and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
- 36 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SLOW FORWARD /
SLOW REVERSE
RESUME
DVD-V CD
DVD-V
1
During playback, hit [STOP C].
¡Resume message will appear on the TV screen.
1
2
During playback, hit [PAUSE F].
Press and hold [g] or [h] for a few
seconds.
1” or “ 1” appears on the screen.
2
Hit [PLAY O], playback will resume from the
point at which playback was stopped.
¡“
¡To cancel resume, hit [STOP C] twice.
¡The resume information stays on even when the
power is turned off.
3
To select another speed, repeat step 2 until
your required speed number appears on the
screen.
¡Slow forward or reverse speed varies with the disc.
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).
¡When you press buttons on the main unit, use
[SEARCH h / g].
PAUSE
DVD-V CD
1
During playback, hit [PAUSE F].
¡Playback will pause and sound will be muted.
4
To return to normal playback, hit [PLAY O].
2
To continue playback, hit [PLAY O].
ZOOM
STEP BY STEP PLAYBACK
DVD-V
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
DVD-V
1
During playback, hit [PAUSE F].
¡Playback will pause and sound will be muted.
1
Hit [ZOOM] during playback.
¡Playback will continue.
2
3
The disc goes forward by one frame each
time [PAUSE F] is hit.
2
Hit [ZOOM] repeatedly to select the required
zoom factor: ZOOM1, ZOOM2, ZOOM3 or
OFF.
To exit step by step playback, hit [PLAY O].
3
4
Press [K / L / s / B] to move the zoomed
picture across the screen.
FAST FORWARD /
FAST REVERSE
To exit zoom mode, hit [ZOOM] to OFF.
NOTES:
DVD-V CD
¡Zooming function does not work while disc menu is
shown.
1
During playback, press and hold [g] or
¡Zooming function is not available on some discs.
¡It may take several seconds to slide the zoomed pic-
ture.
[h] for a few seconds.
¡“ g 1” or “h 1” appears on the screen.
2
To select another speed, repeat step 1 until
your required speed number appears on the
screen.
¡The picture may be distorted if you operate other
F
functions repeatedly (ex. [PAUSE ] or [h], etc.)
in the zoom mode.
¡For DVDs, fast forward/reverse search speed is dif-
ferent depending on the disc. Approximate speed is
1(×2), 2(×8), 3(×20), 4(×50) and 5(×100).
¡For Audio CDs approximate speed is 1(×2), 2(×8)
and 3(×30).
¡When you press buttons on the main unit, use
[SEARCH h / g].
3
To return to normal playback, hit [PLAY O].
- 37 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
DVD-V
CD
There are three ways to begin playback on an Audio
CD at a specific track.
1
2
During playback, hit [SEARCH MODE] three
times (CD: twice) to display the Time Search
on the TV screen.
Using the Number buttons
Within 30 seconds, enter a desired disc
time using the Number buttons.
1
Press the Number buttons to enter the
desired track number.
¡Playback will start at the specified time.
¡Hit [CLEAR] to erase the incorrect input.
¡When there is no need to enter a number, “0”
appears automatically. For example, “ 0 : 0
appears in the Time Search display if the total time
of the track or title is less than 10 minutes.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, hit [3]).
:
”
- -
-
¡To play track 26, hit [+10], [2], [6].
Using [SEARCH MODE]
1
Hit [SEARCH MODE].
¡The track search display appears.
MARKER SETUP SCREEN
DVD-V
CD
2
Within 30 seconds, select the desired track
number using the Number buttons.
Use markers to memorize your favorite places on a
disc.
¡For single digits hit [0] first, if the total track of the
disc is 10 tracks or more.
1
Hit [SEARCH MODE] four times (CD: three
times) during playback.
¡Playback will start at the selected track.
¡The display screen and Markers will appear on the
TV screen.
H G
]
Using [
/
During playback, hit [G] to move the next track. Hit
it repeatedly to skip subsequent tracks. Hit [H] to go
back to beginning of the current track. Hit it repeated-
ly to go to the previous tracks.
2
3
Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,
or 10 and ensure that “
appears in the display.
:
:
”
- - - - - - - -
¡If [H / G] is pressed while the playback is
paused, the playback will be paused again after skip-
ping to the next track.
When you reach the desired point, hit
[ENTER].
NOTE:
¡The Title or Track and elapsed playing time will
appear in the TV screen.
¡[H / G] are not operative when playback is
stopped.
4
To return to the Marker later, hit [SEARCH
MODE] four times (CD: three times) during
playback and press [s / B] to choose the
desired marker, then hit [ENTER].
TITLE / CHAPTER SEARCH
DVD-V
NOTES:
1
Hit [SEARCH MODE] once for the Chapter
search, twice for the Title search during
playback.
¡Operations which erase all Markers:
– Opening the disc tray.
– Turning off the power.
– Hitting [SELECT].
_/2
– Selecting “AC” at step 2 and hitting [ENTER].
¡To clear a marker:
– Press [s / B] to select a cursor on to the marker
number and hit [CLEAR].
2
Enter the desired chapter/title number using
the Number buttons.
¡You can mark up to 10 points.
¡Playback will start at the selected chapter or title.
¡Hit [CLEAR] to erase the incorrect input.
¡For single digits hit [0] first, if the total number of
chapter or title of the disc is 10 or more.
5
Press [SEARCH MODE] or [RETURN] to
exit.
- 38 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
CD
You may determine the order in which tracks will play.
REPEAT is available only during playback.
REPEAT TITLE / CHAPTER
DVD-V
1
In the stop mode, hit [MODE].
¡The “PROGRAM” screen will appear.
To activate the repeat function, hit [REPEAT]
during playback.
¡The repeat mode changes as described below every
time you hit the button.
2
Press [▲ / ▼] to select a track, then hit
[ENTER].
¡Hit [CLEAR] to erase the
most recently entered track.
¡If the entire Program cannot be
displayed at once on a screen,
“G” appears to go to the next
page and “H” appears to go
back to the previous page.
PROGRAM
CD-DA
TOTAL 1:03:30
CHAPTER
TITLE
OFF
(repeat off)
1
5
3:30
5:10
1
3:30
2
3
4
5
6
7
4:30
5:00
3:10
5:10
1:30
2:30
10 4:20
11 3:00
12 3:20
17 4:10
22 2:50
2/3
(current chapter repeat) (current title repeat)
ENTER
1/4
PLAY
1
3:30
CLEAR
NOTES:
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
3
Repeat step 2 until you have selected all the
tracks you want to play in the program.
4
Hit [PLAY O] to play the programmed tracks.
REPEAT TRACK
NOTES:
CD
¡While the program is being played back, hitting
[STOP C] works as follows.
To activate the repeat function, hit [REPEAT]
during playback.
¡The repeat mode changes as described below every
time you hit the button.
¡Hit [STOP C] once and then [PLAY O] again,
playback will restart from the point where
[STOP C] was hit. (Program continued)
¡Hit [STOP C] twice and then [PLAY O] again,
playback will restart from the track in the usual
way. (Program canceled)
TRACK
ALL
OFF
(repeat off)
(current track repeat)
(entire disc repeat)
¡Up to 99 tracks can be entered.
¡To erase all tracks in the program at once, select
“ALL CLEAR” at the bottom of the list at step 2.
¡If you like to repeat the current track in the pro-
gram, hit [REPEAT] several times until
NOTES:
¡Repeat setting will be cleared when moving to other
“
TRACK” appears during playback. If you like
track.
to repeat the entire program hit [REPEAT] several
times until “ ALL” appears during playback.
¡Repeat playback does not function during A-B
repeat playback.
A-B REPEAT
RANDOM PLAYBACK
DVD-V CD
CD
1
¡“
Hit [A-B] at your chosen starting point.
A-” appears briefly on the TV screen.
This function shuffles the playing order of tracks
instead of playback in the sequence.
2
Hit [A-B] again at your chosen end point.
A-B” appears briefly on the TV screen, and the
1
In the stop mode, hit [MODE] twice.
¡“
¡“RANDOM” screen appears.
RANDOM
repeat sequence begins.
CD-DA
TOTAL 0:45:55
RANDOM PROGRAM
no indication
3
To exit the sequence, hit [A-B].
NOTES:
-
-
-
-
PLAY
¡The A-B repeat section can only be set within the cur-
rent title (for DVDs) or current track (for Audio CDs).
¡A-B repeat is not available with some scenes in DVD.
¡To cancel the A point which was set, hit [CLEAR].
¡A-B repeat playback does not function during title,
chapter, track or all repeat playback.
2
Hit [PLAY O] to start random playback.
NOTE:
¡
If you like to repeat the current track in the random
selection, hit [REPEAT] several times until “
TRACK” appears during playback. If you like to
repeat the entire random selection hit [REPEAT] sev-
eral times until “
ALL” appears during playback.
- 39 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
AUDIO LANGUAGE
DVD-V
The unit allows you to select a language for subtitles The unit allows you to select a language during DVD
during DVD disc (if available) playback. disc (if multi languages are available) playback.
DVD-V
1
Hit [SUBTITLE] during playback.
1
Hit [AUDIO] during playback.
¡The subtitle language will
appear on the display bar at
the top of the TV screen.
1.ENG Dolby D 3/2.1ch 48k/3
1.ENG/6
2
Hit [AUDIO] repeatedly to select your
desired language.
2
3
Hit [SUBTITLE] repeatedly to select your
desired subtitle language.
NOTE:
To turn off subtitles, hit [SUBTITLE] repeat-
edly until “OFF” appears.
¡Hitting [AUDIO] may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
NOTES:
¡Hitting [SUBTITLE] may not work on some
DVDs with multiple subtitle languages. In this
case, set it on the disc menu. (Operation varies
between discs. Refer to the manual of the disc.)
¡If the desired language is not shown after hitting
[SUBTITLE] several times, the disc does not have
subtitles in that language.
STEREO SOUND MODE
CD
1
Hit [AUDIO] repeatedly during playback to
select between “STEREO”, “L-ch” or “R-ch”.
STEREO
¡When “NOT AVAILABLE”
NOT AVAILABLE
appears on the TV screen, it
means no subtitle is recorded
on the scene.
¡
STEREO - both right and left channels are active (stereo)
L-ch - only left channel is active
R-ch - only right channel is active
¡If you choose a language that has a 3 letter lan-
guage code, the code will be displayed every time
you change the Subtitle language setting. If you
choose any other languages, “---” will be displayed
instead. (Refer to page 43.)
- 40 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA ANGLE
VIRTUAL SURROUND
DVD-V
DVD-V
CD
Some DVD discs contain scenes which have been shot You can enjoy surround-sound effect over two speak-
simultaneously from various angles. You can change ers on this unit.
the camera angle when the “
screen.
” icon appears on the
1
Hit [MODE] twice (CD: once) during play-
back.
OFF
1
Hit [ANGLE] during playback.
¡The selected angle will be displayed on the display
bar at the top of the screen.
1 / 8
2
3
Hit [ENTER] to set it “1” (Natural effect), “2”
(Emphasized effect) or “OFF”.
¡If the “ANGLE ICON” setting is “OFF” in the
“OTHERS” menu, the “
(Refer to page 45.)
Hit [RETURN] to exit.
” icon will not appear.
NOTE: (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
2
Hit [ANGLE] repeatedly to select your
desired angle.
BLACK LEVEL SETTING
DVD-V
Adjust the Black Level Settings to make the black
parts of the picture brighter.
1
Hit [MODE] during playback.
OFF
2
Hit [ENTER] to switch “ON/OFF”.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
(Initial setting)
3
Press [MODE] twice or [RETURN] to exit.
NOTE:
¡The setting will be saved even if the unit is turned
off.
- 41 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
THE ON-SCREEN INFORMATION
DVD-V
CD
You can check the information about the current disc by hitting [DISPLAY].
For DVD-Vs
For Audio CDs
1
Hit [DISPLAY] during playback to show cur-
rent Chapter.
1
Hit [DISPLAY] during playback to show the
current Track.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
9/49
0:00:00 -0:03:30
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
4/12 0:03:21 - 0:02:15
T
2
Hit [DISPLAY] again to show current Title.
2
Hit [DISPLAY] again to show current Total
Track.
¡The elapsed and remaining
playing time of the current
title will be displayed.
1/3 0:00:00 - 1:23:45
¡The elapsed and remaining playing time of the total
track will be displayed.
4/12 0:03:21 - 0:02:15
T
3
Hit [DISPLAY] again.
¡The bit rate and the current
repeat setting will be
displayed.
T
L1
3
Hit [DISPLAY] again to exit.
¡If you are playing a dual layered disc, the layer
number will also be displayed (L0: Layer 0 is play-
ing. L1: Layer 1 is playing).
NOTE:
¡When you are playing a disc in PROGRAM or RAN-
DOM mode, “ PROGRAM” (or RANDOM) will
be displayed at step 2.
4
Hit [DISPLAY] again to exit.
PROGRAM
B
- 42 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE DVD SET UP ITEMS
Language
Code Language
Code
CUSTOM MENU
A-B
L-N
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
4748 Laothian
4747 Latin
4752 Latvian;Lettish
6563 Lingala
4759 Lithuanian
4764 Macedonian
5471 Malagasy
4765 Malay
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
DVD-V
You can change the DVD player’s settings.
1
Hit [SETUP] twice in the stop mode so that
the DVD SETUP menu appears.
4771 Malayalam
4772 Maltese
4847 Maori
SETUP
¡Hit [L] to select “CUSTOM”
then hit [ENTER].
QUICK
CUSTOM
INITIALIZE
5167 Marathi
Bengali;Bangla
Bhutani
Bihari
4860 Moldavian
5072 Mongolian
4854 Nauru
NOTE:
¡If the menu does not appear, hit [PLAY O] first,
then hit [STOP C]. Make sure the disc is in the stop
mode, then slowly hit [SETUP] twice.
Bislama
Breton
4855 Nepali
4864 Norwegian [NOR]
4853
5971 Occitan
4851 Oriya
Oromo(Afan)
5759 Panjabi
4947 Pashto;Pushto
7254 Persian
4961 Polish
5464 Portuguese [POR]
4965 Quechua
5047 Rhaeto-Romance
6058 Romanian [RUM]
5160 Russian [RUS]
5161
5166 Samoan
Sangho
5261 Sanskrit
5256 Scots Gaelic
5255 Serbian
Bulgarian
Burmese
Byelorussian
O-R
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
2
Select the desired item.
C-E
¡Press [K / L] to select the desired item then hit
Cambodian
Catalan
[ENTER] to confirm.
Chinese [CHI]
Corsican
Croatian
Refer to the pages below to set up each item.
SETUP
CUSTOM
A
P 43 Step
Czech
3
3
3
3
3
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
B
P 44 Step
C
P 44 Step
S
D
P 45 Step
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
E
F-H
P 45 Step
LANGUAGE SETTING
Faroese
Fiji
A
Finnish [FIN]
French [FRE]
Frisian
5264 Serbo-Croatian
5271 Sesotho
5358 Setswana
5747 Shona
Follow steps to in the “CUSTOM MENU” section
1
2
above.
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
3
Press [K / L] to select the desired item then
5051 Sindhi
hit [ENTER].
5158 Singhalese
5758 Siswat
5360 Slovak
SETUP
LANGUAGE
AUDIO:
AUDIO
SUBTITLE
DISC MENU
ORIGINAL
OFF
ENGLISH
Sets the audio language.
Gujarati
Hausa
Hebrew
5367 Slovenian
5447 Somali
5569 Spanish [SPA]
5455 Sundanese
5467 Swahili
SUBTITLE:
Sets the subtitle language.
DISC MENU:
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Swedish [SWE]
Sets the language for DVD menu.
5565
5560 Tagalog
5547 Tajik
5551 Tamil
5557 Tatar
5347 Telugu
5566 Thai
T
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
4
Press [K / L] to select a setting then hit
[ENTER].
SETUP
LANGUAGE
LANGUAGE
LANGUAGE
AUDIO
¡If “OTHER” is selected on
the “AUDIO”, “SUBTITLE”
or “DISC MENU” screen,
press four-digit number to
enter the code for the desired
language. (Refer to the lan-
guage code list.)
ORIGINAL
ENGLISH
FRENCH
5647 Tibetan
5669 Tigrinya
5760 Tonga
5765 Tsonga
5757 Turkish [TUR]
6469 Turkmen
5771 Twi
SETUP
SUBTITLE
OFF
ENGLISH
FRENCH
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
6460
U-Z
¡Only the languages support-
ed by the disc can be select-
ed.
5761 Ukrainian
5767 Urdu
Uzbek
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
SETUP
DISC MENU
ENGLISH
FRENCH
Vietnamese
Volapuk
Welsh
SPANISH
Wolof
Xhosa
Yiddish
Yoruba
Zulu
5
Hit [SETUP] to exit the menu.
NOTES:
¡Language Setting for Audio and Subtitle are not
valid for some discs due to default setting of the
disc. In this case, set them by hitting [AUDIO] and
[SUBTITLE]. (Refer to page 40.)
¡If you select a language that is not supported by the
disc, subtitle will automatically be set OFF and the
first item of the audio languages will be automatical-
ly set.
If you choose a language that has a 3 letter language
code, the code will be displayed every time you change
the AUDIO or SUBTITLE language setting above. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
- 43 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
B
C
DISPLAY SETTING
AUDIO SETTING
Choose the appropriate Audio settings for your equip-
ment as it only affects during the playback of DVD
discs.
Follow steps to in the “CUSTOM MENU” sec-
tion on page 43.
1
2
3
Press [K / L] to select the below items then
hit [ENTER].
Follow steps to in the “CUSTOM MENU” sec-
tion on page 43.
1
2
TV MODE:
QUICK
3
Press [K / L] to select the below items then
hit [ENTER].
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
DRC (Dynamic Range
Control):
¡To compress the range of soft
to loud sound.
SETUP
DRC
DOWN SAMPLING
DOLBY DIGITAL
AUDIO
¡4:3 LETTER BOX (default):
To show black bars on top
and bottom of the screen.
SETUP
DISPLAY
ON
ON
BITSTREAM
TV MODE
STILL MODE
4:3 LETTER BOX
AUTO
¡4:3 PAN & SCAN: To show
a full height picture with both sides trimmed.
¡The default setting is “ON”.
SETUP
AUDIO
DOWN SAMPLING:
¡ON : Output in 48 kHz.
(default)
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
BITSTREAM
STILL MODE
This function allows you to adjust picture resolution
and quality in the still mode.
:
¡OFF : Output the original
sound.
SETUP
DISPLAY
¡AUTO (default):
When playing disc with copyright Protection
¡If you select “OFF”, copyright protection will be
activated and sound will be down sampled at 48kHz.
TV MODE
STILL MODE
4:3 LETTER BOX
AUTO
Automatically select the best
resolution setting (FRAME
or FIELD) based on the data
characteristics of the pictures.
¡FIELD: Select “FIELD” when the pictures are still
unstable even if “AUTO” is selected.
FIELD stabilizes the pictures, although the picture
quality may become coarse due to the limited
amount of data.
SETUP
DRC
DOWN SAMPLING
DOLBY DIGITAL
AUDIO
DOLBY DIGITAL:
QUICK
ON
ON
BITSTREAM
Set to “BITSTREAM” when
the unit is connected to a
Dolby Digital Decoder.
¡BITSTREAM: Output a Dolby Digital signal
¡FRAME: Select “FRAME” to display relatively
motionless pictures in higher resolution.
FRAME improves the picture quality, although it
may unstabilizethe pictures due to simultaneous
output of two field data.
(default)
¡PCM: Convert the Dolby Digital to PCM
(2 channel stereo)
4
Hit [SETUP] to exit the menu.
4
Hit [SETUP] to exit the menu.
QUICK MENU
¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the
QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 43.
1
LANGUAGE SETTING FOR THE ON-SCREEN MENUS
¡You can access the TV/VCR SETUP menu by hitting [SETUP] from the DVD mode. Refer to
“MENU LANGUAGE” on page 21 to change the language for the on-screen menus.
- 44 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
D
PARENTAL CONTROL
IF YOU FORGET THE PASSWORD
Parental Control limits the disc viewing that exceed
your setting (with a password or playback will stop).
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
1
Hit the Number buttons [4], [7], [3], [7] at
step 3. Then enter your new password.
¡Password will be cleared and parental level will be
set to “ALL”.
PARENTAL LEVEL
2
Proceed with steps 4 to 6 again.
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
E
OTHER SETTINGS
Follow steps to in the “CUSTOM MENU” sec-
tion on page 43.
1
2
Follow steps to in the “CUSTOM MENU” sec-
1
2
tion on page 43.
3
Press [K / L] to select the below items,
3
4
5
6
Enter your four-digit password then hit
[ENTER].
then hit [ENTER].
SETUP
OTHERS
SETUP
PARENTAL
ANGLE ICON
AUTO POWER OFF ON
ON
PASSWORD
Enter current password.
ANGLE ICON:
¡Hit [ENTER] repeatedly to turn Angle icon “ON” or
“OFF”.
Press [K / L] to select “PARENTAL LEVEL”
then hit [ENTER].
¡The default setting is “ON”.
SETUP
PARENTAL
AUTO POWER OFF:
¡Hit [ENTER] repeatedly to turn Auto Power off
“ON” or “OFF”.
The default setting is “ON” and the screen saver pro-
gram starts when there is no input from the unit for 5
minutes in the stop mode. After the screen saver pro-
gram is activated for 15 minutes, the power is auto-
matically turned off.
PARENTAL LEVEL
PASSWORD CHANGE
ALL
¡
Press [K / L] to select the desired level
then hit [ENTER].
SETUP
PARENTAL
PARENTAL LEVEL
ALL
8
7 [NC-17]
6 [R]
4
Hit [SETUP] to exit the menu.
Hit [SETUP] to exit the menu.
NOTES:
INITIALIZE
¡
When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the pass-
word. (in the event you forget the password, see below)
DVD-V
This allows you to return all selections of SETUP
(except for “PARENTAL” and menu language) to
their default settings.
¡To change the password, press [K / L] to select
“PASSWORD CHANGE” at step 4 then hit
[ENTER]. Enter the four-digit password, then hit
[ENTER].
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
1
2
Hit [SETUP] twice in the stop mode so that
the “INITIALIZE” menu appears.
Press [K / L] to select “INITIALIZE” then hit
[ENTER].
SETUP
QUICK
CUSTOM
INITIALIZE
¡Record the password in case you forget it.
CONTROL LEVELS
3
Press [K / L] to select “YES” then hit
¡
ALL
[ENTER] twice.
SETUP
INITIALIZE
All parental lock is cancelled.
All the settings (except for
“PARENTAL” and menu
language) will be cleared.
Initialize?
NO
YES
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
¡To cancel the initialization, select “NO”.
¡
Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
4
Hit [SETUP] to exit the menu.
¡
Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
- 45 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-
sulting the following checklist.
PROBLEM
CORRECTIVE ACTION
Make sure the power plug is connected to an AC outlet.
Make sure the power is turned on.
Check if the power plug is connected to an AC outlet.
Check the batteries in the remote control.
Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote control.
You have to be within 23 feet of the unit.
No power
•
•
•
•
•
No operation by infrared remote
control
•
•
Check if the correct mode is selected. If not switch the mode by
hitting [SELECT], whichever you need.
TV/VCR Mode
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
No picture or sound
CORRECTIVE ACTION
Make sure the AC cord is connected to an AC outlet.
Check antenna connection.
Hit [SELECT] to select TV mode.
Then try other TV feature.
•
•
•
Let the unit program its tuner memory.
Adjust direction or replace antenna.
Adjust picture controls.
Check for broken pin of the antenna cable.
Adjust volume control on remote control or main unit.
Hit [MUTE] to restore sound.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
No picture or poor picture on the
unit
No sound or poor sound
Bars On Screen
If outside antenna is being used, check for broken wire.
Check for local interference.
Picture Distorted or Blurred
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust “COLOR” control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust “CONTRAST” & “BRIGHT” control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
Adjust “CONTRAST” & “BRIGHT” control.
- 46 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
Picture OK, Sound Poor
CORRECTIVE ACTION
Try a new channel, if OK, then possible station trouble.
Check for local interference.
Make sure the timer recording is set correctly.
Make sure the power is off.
Make sure the unit’s clock is set correctly.
Make sure the tape has an erase-prevention tab. If need, cover the
hole with plastic tape.
Adjust tracking control for a better picture using [CHANNEL X / Y]
on the unit.
Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 49.
Make sure the AC cord is connected to an AC outlet.
Check batteries in remote control.
You can not copy a copyrighted video tape. You are experiencing
•
•
•
•
•
•
•
Timer recording is not possible
Cannot go into the recording mode
Playback picture is partially noisy
•
•
•
No picture but the audio is OK in
playback
No operation by infrared remote
control
Video or color fades in and out
when making a copy of a video tape
•
•
•
copy guard protection.
Magnetism from nearby appliances and geomagnetism might affect
the color of the TV picture. Move the unit away from the appliances,
the unit can repair itself automatically. If you want to repair immedi-
ately, unplug the power cord, then plug it in again 30 minutes later or
so. This automatically resets the unit.
•
Different color marks on screen
•
CLOSED CAPTION PROBLEM
POSSIBLE REMEDY
Misspelling in captions
Error committed by the closed captioning production company.
Possible in a live broadcast. Not in case of a prerecorded program.
A few seconds of delay is common for live broadcast.
Display capacity may not exceed 220 words per minute. If a dialogue
exceeds that rate, selective editing is used to insure that the captions
remain up-to-date with the current TV screen dialogue.
Caused by interferences of building, power lines, thunderstorms, etc.
•
•
Text is not shown in its entirety or
a delay occurs from what is being
said
•
•
•
•
Captions scrambled with white
boxes
•
No captions in a program which
must contain closed caption
The broadcast may use a time compression process to speed up the
program. The decoder cannot read the compressed information and
captions will be lost.
Possibility of a illegal copy or an erroneous copying process
•
•
•
No captions in a prerecorded
videotape which indicated closed
captions included.
•
accidentally performed by the fabricator.
•
Black box in the TV screen
You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or
Caption “OFF”.
•
•
- 47 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Mode
PROBLEM
CORRECTIVE ACTION
Insert a correct video disc that plays on this unit.
Hit [SELECT] to select DVD mode, then try other DVD feature.
Insert the disc.
No picture
•
•
•
•
•
•
•
•
•
•
•
•
Disc cannot be played
Clean the disc.
Place the disc correctly, with the label side up.
Cancel the parental lock or change the control level.
Connect the audio cables firmly.
Turn the power of the audio component on.
Correct the audio output settings.
No sound
Correct the input settings on the audio component.
This unit does not support DTS audio. This is not a malfunction.
No DTS audio is output
Distorted picture
There are some cases where pictures may be slightly distorted,
which are not a sign of a malfunction.
Although pictures may stop for a moment, this is not a malfunction.
The selected language is not available for audio or subtitles on the
DVD. (This is not a malfunction.)
•
•
Audio or subtitle language
does not match the set up
The camera angle cannot be changed The DVD does not contain sequences recorded from different
•
camera angles. (This is not a malfunction.)
Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected
•
changed
language. (This is not a malfunction.)
That operation is prohibited by the unit or the disc.
(This is not a malfunction.)
•
•
•
•
“Prohibited icon” appears on the
screen, prohibiting an operation
CD sound dropout
No CD reproduction
DVD picture dropout
DVD picture freeze
Scratched disc. Replace the disc with an unscratched one.
DVD picture in mosaic
No DVD reproduction
NOTES:
Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
•
- 48 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.Please visit your local Audio/Video store and pur-
CABINET CLEANING
chase a good quality VHS Video Head Cleaner.
2.If a Video Head Cleaner does not solve the prob-
lem, please call our help line mentioned on the
front page, to locate an Authorized Service Center.
NOTES:
Wipe the front panel and other exterior surfaces of
the unit with a soft cloth immersed in lukewarm
water and wrung dry.
•
Never use a solvent or alcohol. Do not spray insec-
•
ticide liquid near the unit. Such chemicals may
cause damage and discoloration to the exposed sur-
faces.
Remember to read the instructions included with
the video head cleaner before use.
•
Clean video heads only when problems occur.
•
AUTO HEAD CLEANING
SERVICING
Automatically cleans video heads as you insert or
remove a cassette, so you can see a clearer picture.
•
Should your unit become inoperative, do not try to
•
correct the problem by yourself. There are no user-
serviceable parts inside. Turn off, unplug the power
cord and please call our help line mentioned on
the front page, to locate an Authorized Service
Center.
Playback picture may become blurred or interrupt-
•
ed while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during play-
back, the video heads in your unit may need to be
cleaned.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
If the unit still does not perform properly when it is operated, while referring to the relevant sections and to
“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.
•
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup
unit.
DISC HANDLING
Handle the discs so that fingerprints and dust do
not adhere to the surfaces of the discs.
To clean-off, use a soft cloth.
•
•
•
•
•
•
•
Do not use a hard cloth since this will mar the disc.
Wipe the disc in a straight line from center to edge.
Never wipe with a circular motion.
Do not use detergent or abrasive cleaning agents.
Always store the disc in its protective case when it
is not used.
- 49 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
TV/VCR
CRT:
27 inch in-line gun,
90˚ deflection tube
NTSC-M
OTHER SPECIFICATIONS
Terminals
Television system:
Closed caption system: §15.119/FCC
Antenna input:
VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
Video Heads:
Tape width:
Tape speed
SP:
LP:
SLP:
Tuner channel
TV VHF Low:
TV VHF High:
TV UHF:
CATV
Rotary four-head
1/2 inch
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output:
1/8” stereo (3.5 mm)
33.40mm/sec.
16.67mm/sec.
11.12mm/sec.
One pin jack,
500m Vpp (75 ohm)
Digital encoded
Remote control:
#2~#6
#7~#13
#14~#69
infrared light system
Operating
temperature:
5°C to 40°C
(41°F~104°F)
Power requirements: AC 120V, 60Hz
Power consumption
VHF:
5A
MID band:
SUPER band:
HYPER band:
A5~A1, A~I
J~W
W+1~W+84
(Maximum):
Picture tube:
Dimensions:
120W
27"
H : 25-1/2" (648mm)
W : 26-9/16" (675mm)
D : 19-11/16" (500mm)
86.0 lbs. (39kg)
Weight:
DVD
Product type:
Discs:
DVD Player
DVD video, Audio CD
Output signal format: NTSC color
Designs and specifications are subject to change without notice.
If there is a discrepancy between languages, the default language will be English.
•
•
- 50 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Botón REC/OTR (Panel frontal)
Presione para empezar la grabación manual. Presione
repetidamente para empezar la grabación instantánea
(OTR).
INDICE
■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 51
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 52
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 52
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 52
CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 53
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
Botón RECORD (Mando a distancia)
Presione para empezar la grabación manual.
14. Botón REW R (para TV/VCR)
Presione para rebobinar la cinta o para ver la imagen
rápidamente en dirección de retroceso durante el modo
de reproducción. (Búsqueda en dirección de retroceso)
EQUIPADO CON TOMAS DE ENTRADA DIGITAL.
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
15. Botón F.FWD Q (para TV/VCR)
Presione para adelantar rápidamente la cinta o para ver la
imagen rápidamente en dirección de avance durante el modo
de reproducción. (Búsqueda en dirección de avance)
SECCIÓN DE TV/VCR
16. Botón STOP/EJECT P N
■ FUNCIONES Y AJUSTES DE TV. . . . . . . . . . . . . . . . . 54
PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 54
IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
■ GRABACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
GRABACIÓN NORMAL . . . . . . . . . . . . . . . . . . . . . . . . 55
Presione para detener la cinta. Presione en el modo de
parada para retirar la cinta de la unidad.
17. Ventanilla del sensor de mando a distancia
18. Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar
en privado.
SECCIÓN DE DVD
19. Toma de entrada VIDEO
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55
MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Conecte aquí la toma de salida de video de una
videocámara o de una videograbadora.
20. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
CONTROLES DE
OPERACIÓN Y FUNCIONES
21. Compartimiento del cassette
22. Botón PICTURE
• Consulte la figura 1 de la página 9 para el
Presione para ajustar la imagen.
panel frontal de la unidad
23. Botones numéricos
• Consulte la figura 2 de la página 9 para el
mando a distancia
Modo TV/VCR:
Presione dos cifras para acceder directamente al canal
deseado.
• Consulte la figura 3 de la página 10 para la
vista posterior
No olvide presionar [0] antes de elegir un canal de una
sola cifra.
1. Botón POWER
Botón +100
Presione para encender y apagar la unidad.
Presione para seleccionar canales de televisión por
cable cuyo número sea superior a 99.
Modo DVD:
2. Botones VOLUME (VOL.) X / Y
Presione para controlar el nivel de volumen del DVD y
el televisor.
3. Botones SKIP U / T (para DVD)
Presione una vez para omitir capítulos o pistas y
desplazarse a un punto específico.
Botones SEARCH E / D (para DVD)
Mantenga el botón presionado para cambiar la
velocidad de reproducción en avance o retroceso.
Presione para introducir el número deseado.
Botón +10
Presione para introducir números superiors a 9.
24. Botón PAUSE F
Hace una pausa en la reproducción del disco o cinta.
25. Botón SPEED
Presione para seleccionar la velocidad de grabación
deseada: SP/SLP.
4. Botón PLAY O
Inicia la reproducción del contenido del disco o cinta.
26. Botón C.RESET
5. Botón STOP P
Presione para poner el contador en 0:00:00.
Presione también para cancelar un ajuste de programa
de temporizador.
(Panel frontal) Detiene la operación del disco.
(Mando a distancia) Detiene la operación del disco o el
casete.
27. Botón DISPLAY
6. Botón OPEN/CLOSE N
Presione para insertar un disco en la bandeja o retirarlo
de ella.
Modo TV/VCR:
Indica el contador o el número del canal y la fecha
actual en la pantalla del televisor.
Modo DVD:
7. Bandeja de carga del disco
8. Indicador DVD
Indica el estado actual en la pantalla del televisor.
Se ilumina durante el modo DVD.
28. Botón SETUP
9. Botón SELECT
Presione para entrar o salir del menú de configración
de televisor o DVD.
Presione para cambiar al modo TV/VCR, modo de
entrada externa o modo de DVD. El modo
seleccionado (TV/VCR o DVD) se visualiza en el
indicador del panel delantero.
29. Botón TITLE
Para visualizar el menú de títulos.
30. Botón CLEAR
10. Indicador TV/VCR
Presione para cancelar o borrar un ajuste entrado
actualmente.
Se ilumina durante el modo TV/VCR.
11. Botones CHANNEL (CH.) X / Y
Utilice para seleccionar canales memorizados.
31. Botón MODE
Presione para llamar la pantalla de la reproducción programada
o la de reproducción aleatoria en el modo de parada.
Presione para llamar la pantalla de ajuste del nivel del negro o
la pantalla de sonido ambiental durante la reproducción.
12. Indicador de grabación
Parpadea durante la grabación. Se ilumina durante el
modo de espera de grabación controlada por
temporizador.
- 51 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
32. Botón SEARCH MODE
PREPARACIÓN PARA LA
UTILIZACIÓN
Presione para localizar un punto deseado.
33. Botón AUDIO
Modo TV/VCR:
Presione para seleccionar el modo de sonido deseado
cuando vea un programa de TV o reproduzca o grabe
un casete.
CONEXIONES DE ANTENA/CABLE
Consulte la figura 4 de la página 12
Modo DVD:
ANTENA COMBINADA DE VHF/UHF
La antena combinada de VHF/UHF de 75 ohmios puede
conectarse a la toma ANT.
ANTENAS SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena exterior.
Presione para seleccionar un modo de sonido o idioma
de audio deseado.
34. Botón SUBTITLE
Presione para seleccionar el idioma de subtítulos
deseado.
35. Botón REPEAT
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a la unidad, sin una
caja de convertidor.
Repite la reproducción del disco, título, capítulo o pista
actual.
36. Botón ANGLE
Presione para cambiar el ángulo de la cámara y ver la
secuencia que se está reproduciendo desde un ángulo
diferente (si existe).
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
37. Botón A-B (modo DVD)
Repite la reproducción de una sección seleccionada.
38. Botón RETURN
Permite volver a la pantalla anterior en el menú de
configuración.
Si su compañía de televisión por cable le suministra
una caja de convertidor o si utiliza un sistema de
satélite, podrá utilizar la conexión básica que se
muestra en la ilustración.
39. Botón ENTER
Presione para establecer un ajuste.
40. Botones K / L / { / B
La selección de los canales deberá hacerse con la caja de
convertidor o con la caja de satélite. Esto significa que
no es posible cambiar de canal utilizando el mando a
distancia de la unidad.
Modo TV/VCR:
Presione para seleccionar un modo de ajuste en el
menú que aparece en la pantalla del televisor.
Presione también para seleccionar o establecer ajustes
en un menú en particular.
Modo DVD:
Presione para hacer una selección en el menú.
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención
del instalador de sistemas CATV para que tenga
en cuenta el Artículo 820-40 de la NEC, que
proporciona recomendaciones para hacer una
conexión a tierra apropiada y, en particular,
especifica que la tierra del cable debe conectarse
al sistema de puesta a tierra del edificio, tan cerca
del punto de entrada del cable como sea posible.
41. Botón DISC MENU
Muestra menú del DVD.
42. Botón ZOOM
Amplía parte de la imagen reproducida de un DVD.
43. Botón MUTE
Suprime la salida de sonido. Presione de nuevo para
restablecer el sonido.
44. Botón SLEEP
Utilice para ajustar el temporizador de dormir.
45. Toma ANT.
NOTA:
Conecte a una antena, sistema de televisión por cable o
sistema de satélite.
Antes de enchufar la antena a la toma ANT. de la
unidad, compruebe que la clavija no esté doblada.
Si esta doblada, póngala derecha como se muestra
en la ilustración, y luego conéctela en la toma
ANT. de la unidad.
46. Cable de alimentación
Conecte a un toma de CA estándar (120 V/60 Hz).
NOTA:
Antes de conectar el cable de alimentación de una
•
toma de CA estándar, retírelo del gancho para evitar
dañarlo.
Clavija doblada
47. Toma AUDIO OUT COAXIAL
Conecte solamente a la entrada digital de un
amplificador externo o decodificador (para audio de
DVD solamente).
Cable
Clavija
(Necesita enderezarse)
(Clavija derecha)
NOTA:
PARA INSERTAR LAS PILAS
Para su seguridad y para evitar que se dañe
la unidad, desenchufe el cable de antena de la
toma ANT. antes de mover la unidad.
•
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a
distancia en el sentido de la flecha.
2) Inserte 2 pilas “AA” en el
compartimiento de las pilas, en el
sentido indicado por las marcas de polaridad (+/-).
3) Vuelva a poner la cubierta.
- 52 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
CONEXIÓN A TOMAS DE
ENTRADA DELANTERAS
CONEXIÓN A UN DECODIFICADOR
DOLBY DIGITAL (para DVD)
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de
entrada AUDIO/VIDEO de la parte delantera de la
unidad.
Conecte las tomas de salida de audio/vídeo de otra
fuente a las tomas AUDIO L/R y VIDEO de esta
unidad.
Si utiliza esta unidad para reproducir un disco DVD
grabado en formato de sonido envolvente Dolby
Digital de 5,1 canales, la unidad emitirá un flujo de
datos DOLBY DIGITAL desde su toma AUDIO
OUT COAXIAL. Si conecta la unidad a un
decodificador Dolby Digital, podrá disfrutar de una
tonalidad más convincente y real, con un sonido
envolvente potente y de alta calidad similar al de los
cines.
Después, presione [SELECT] o [CH. K / L] hasta
que aparezca “AUX” en la pantalla.
Utilice cables digitales coaxiales de audio
(disponibles en el comercio) para hacer las
conexiones de audio.
Consulte la figura 5 de la página 13
NOTA:
Cuando conecte una videograbadora monofónica
•
Consulte la figura 7 de la página 14
(otra fuente) a esta unidad, conecte la toma de
salida de audio de la videograbadora monofónica
(otra fuente) a la toma AUDIO L de esta unidad. El
audio saldrá igualmente por los canales izquierdo y
derecho.
NOTAS:
Asegúrese de apagar todos los componentes del
•
sistema antes de conectar otro componente.
Consulte los manuales de instrucciones de los
•
componentes que va a conectar a la unidad.
CONEXIÓN A UN AMPLIFICADOR
ESTÉREO EQUIPADO CON TOMAS
DE ENTRADA DIGITAL (para DVD)
Utilice un cable digital coaxial de audio (disponible en
el comercio) para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de
entrada digital, platina MD o platina DAT.
Si conecta un decodificador Dolby Digital, ajuste
•
la función “DOLBY DIGITAL” a “BITSTREAM”
para salida de audio en el modo de configuración.
A menos que se haga la conexión a un
•
decodificador Dolby Digital, ajuste la función
“DOLBY DIGITAL” a “PCM” para salida de
audio en el modo de configuración. La
reproducción en una unidad utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede provocar daños a los altavoces.
Consulte la figura 6 de la página 13
NOTAS:
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la
doble D son marcas comerciales de Dolby
Laboratories.
• La fuente de audio de un disco grabado en formato
de sonido envolvente Dolby Digital de 5,1 canales
no se puede grabar como sonido digital mediante
una platina MD o DAT.
Asegúrese de apagar todos los componentes del
•
• sCisotnesmulateanlotessmdaencuoanleesctdaer ointrsotrucoccmiopnoensendtee.los
• Acojmuspteonlaenftuenscqióune “vDa Oa LcoBnYecDtaIrGaITlaAuLn”idaa“dP. CM”
para salida de audio en el modo de configuración.
La reproducción en una unidad utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede provocar daños a los altavoces.
- 53 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
IDIOMA DEL MENÚ
SECCIÓN DE TV/VCR
TV/VCR
FUNCIONES Y AJUSTES
DE TV
1 Seleccione “LANGUAGE”
Presione [SETUP].
Presione [K / L] para apuntar a “LANGUAGE”.
PARA MIRAR UN PROGRAMA DE TV
TV/VCR
2 Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS”
1 Enchufe el cable eléctrico
Enchufe el cable eléctrico de la unidad en un
tomacorriente de CA del hogar.
NOTA:
Presione [ENTER] repetidamente para seleccionar
“ENGLISH” = inglés, “ESPAÑOL” o
“FRANÇAIS” = francés.
Si aparecen números en la esquina de la pantalla,
•
3 Salga del modo de idioma
Presione [SETUP] para salir del menú.
NOTAS:
presione [POWER] sin desenchufar el cable
eléctrico.
Esta función afecta sólo el idioma en el menú de la
pantalla y no la fuente de audio.
Si por alguna razón, el menú está en francés,
presione [SETUP], presione [K / L] para apuntar
al “LANGAGE [FRANÇAIS]” y presione
[ENTER] repetidamente para seleccionar el
idioma deseado y presione [SETUP].
•
2 Encienda la unidad
Presione [POWER] para encender la unidad.
•
3 Seleccione el número de canal
Presione [CH. K / L] o los botones numéricos para
seleccionar su número de canal deseado.
Nota para el uso de los botones numéricos:
¡Debe colocar un cero antes de los números de canal
de una sola cifra (por ejemplo: 02, 03, 04, etc.).
¡
Cuando seleccione canales de cable de más de 99,
presione primero [+100] y después las dos últimas
cifras. (Ejemplo: para seleccionar el canal 125,
primero presione [+100] y después presione [2] y [5].)
AJUSTE DEL RELOJ
TV/VCR
AJUSTE MANUAL DEL RELOJ
Asegúrese ...
La unidad debe estar encendida.
En el siguiente ejemplo, el reloj debe estar en:
4 Ajuste el sonido
•
Presione [VOL. X / Y] para ajustar el volumen.
Presione [MUTE] para silenciar instantáneamente el
sonido.
FECHA
HORA DE AJUSTE
6 de mayo, 2005
5:40PM
Presione nuevamente para recuperar el nivel de
sonido anterior.
NOTA:
1 Seleccione “AJUSTE RELOJ”
Presione [SETUP].
Presione [K / L] para seleccionar “AJUSTE RELOJ”
y presione [ENTER].
Si presiona [CH. K / L] en el modo DVD, puede
•
cambiar los canales de TV. Incluso si apaga la
unidad en el modo DVD, cuando vuelva a
encender, volverá al modo TV/VCR.
PARA VER CANALES DE CABLE O
SATELITE
2 Seleccione “AJUSTE MANUAL RELOJ”
Presione [K / L] para seleccionar “AJUSTE
MANUAL RELOJ” y presione [ENTER].
Si la unidad está conectada a una caja de cable o
•
caja de satélite, presione [CH. K / L] para
seleccionar CH3 o CH4 de acuerdo con el ajuste
de canal de salida del dispositivo y seleccione el
canal deseado en el dispositivo.
3 Seleccione el mes
Presione [K / L] hasta que aparezca el mes deseado.
(Ejemplo: Mayo → “05”)
PARA VER UNA ENTRADA EXTERNA
Presione [B]. (O presione [s] para volver un paso.)
Cuando se conecta un equipo externo en las tomas
•
de entrada AUDIO/VIDEO frontales, presione
[SELECT] o [CH. K / L] repetidamente hasta que
aparezca “AUX” en la pantalla.
4 Seleccione el día
Presione [K / L] hasta que aparezca el día deseado.
(Ejemplo: 6º → “06”)
Presione [B].
- 54 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
SECCIÓN DE DVD
5 Seleccione el año
REPRODUCCIÓN BÁSICA
Presione [K / L] hasta que aparezca el año deseado.
(Ejemplo: “2005”)
DVD-V
CD
Presione [B].
Para empezar
¡Conecte la alimentación del amplificador y otros
6 Seleccione la hora
componentes, si es necesario.
Presione [K / L] hasta que aparezca la hora deseada.
(Ejemplo: “5”, “PM”)
1
Presione [POWER].
¡La alimentación se conectará.
Presione [B].
2
3
4
Presione [OPEN/CLOSE N] para abrir la
bandeja de carga del disco.
7 Seleccione los minutos
Presione [K / L] hasta que aparezcan los minutos
deseados.
Ponga el disco deseado en la bandeja, con
la etiqueta hacia arriba.
(Ejemplo: “40”)
Presione [PLAY O].
¡La bandeja se cerrará automáticamente y la
reproducción comenzará desde el primer capítulo o
pista del disco.
8 Haga funcionar el reloj
Presione [SETUP].
Aunque no aparezcan los segundos, empezará a
contar desde 00 cuando presione [SETUP]. Utilice
esta característica para sincronizar el reloj con la hora
real.
¡La reproducción también empieza cerrando
manualmente la bandeja del disco o presionando
[OPEN/CLOSE N].
¡Si la reproducción no comienza automáticamente,
presione [PLAY O].
¡
Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú podrá aparecer en la pantalla.
GRABACIÓN
GRABACIÓN NORMAL
TV/VCR
5
Presione [STOP
C] para detener la reproducción.
MENÚ DE DISCO
SOLO puede ver el mismo programa que se está
grabando.
DVD-V
1
Presione [DISC MENU].
¡Aparecerá el menú principal de DVD.
1 Seleccione el canal a grabar
Presione los botones numéricos o [CH. K / L].
NOTA:
¡Si no existe la función, puede aparecer el símbolo
en la pantalla de TV.
¡Si el menú de disco existe en el disco, aparecerán el
idioma de audio, opciones de subtítulo, capítulos
para el título y otras opciones para su selección.
Si la unidad está conectada a una caja de cable o
•
caja de satélite, la unidad debe estar en CH3 o
CH4 y debe seleccionarse el canal a grabar en la
caja de cable o caja de satélite.
2
Presione [K / L / s / B] para seleccionar
un ítem y presione [ENTER] para confirmar
la selección.
2 Seleccione la velocidad de la cinta
Presione [SPEED] para seleccionar la velocidad de
cinta deseada (SP/SLP).
REANUDACIÓN
DVD-V
CD
3 Empiece a grabar
Presione [RECORD].
1
Durante la reproducción, presione
[STOP C].
¡
Aparecerá el mensaje de continuación en la pantalla de TV.
4 Pare la grabación
Presione [STOP C].
2
Presione [PLAY O], la reproducción continuará
desde el punto donde se paró la reproducción.
¡Para cancelar la continuación, presione dos veces
[STOP C].
¡La información de continuación permanece activada
incluso cuando apaga el interruptor principal.
- 55 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to
any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service inquiries,
please call or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-968-3429
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
1EMN20316
T2135UF ★★★★★
Download from Www.Somanuals.com. All Manuals Search And Download.
|