Sylvania TV VCR Combo 6719DES User Manual

OWNER’S

MANUAL

COLOR TV/VCR/DVD TRIPLE COMBO

(19 inch)

6719DES

SKIP

PLAY

SKIP

STOP

OPEN/CLOSE

SELECT

CHANNEL

REC/OTR

REW

PLAY

F.FWD

STOP/EJECT

POWER

VOLUME

HEADPHONE VIDEO

AUDIO

DVD

TV/VCR

SUPPLIED ACCESSORIES

ACCESSORIES

PART NO.

Remote Control Unit NE222UD

Batteries

2 AA Batteries

1EMN20035

Owner’s Manual

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®

is a U.S. registered mark.

If you need additional operating assistance after reading this owner’s

manual or to order replacement accessories, please call

TOLL FREE : 1-800-968-3429.

Or visit our WEB SITE at http://www.funai-corp.com

Please read before using this equipment

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR/DVD, be sure

the antenna or cable system is grounded so as to provide

some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR/DVD

from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR/DVD.

c. If the TV/VCR/DVD has been exposed to rain or water.

d. If the TV/VCR/DVD does not operate normally by follow-

ing the operating instructions. Adjust only those controls

that are covered by the operating instructions, as improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the TV/VCR/DVD to its normal operation.

14.Lightning-For added protection for this TV/VCR/DVD

receiver during a lightning storm, or when it is left unat-

tended and unused for long periods of time, unplug it from

the wall outlet and disconnect the antenna or cable system.

This will prevent damage to the TV/VCR/DVD due to

lightning and power-line surges.

e. If the TV/VCR/DVD has been dropped or damaged in any

way.

f. When the TV/VCR/DVD exhibits a distinct change in per-

formance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

16.Overloading-Do not overload wall outlets and extension

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR/DVD, ask the service technician to perform

routine safety checks to determine that the TV/VCR/DVD

is in proper operating condition.

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR/DVD through openings as they may

touch dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the TV/VCR/DVD.

22.Heat-This TV/VCR/DVD product should be situated away

from heat sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR/DVD

yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

- 3 -

1B15

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LASER SAFETY

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

This product incorporates copyright protection tech-

nology that is protected by method claims of certain

U.S. patents and other intellectual property rights

owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology

must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing

uses only unless otherwise authorized by

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

RADIO-TV INTERFERENCE

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

- 4 -

1B15

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

LOCATION

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a TV/VCR/

DVD which has moisture, it may damage the DVD

and TV/VCR/DVD. Therefore when the condensation

occurs inside the unit, turn the POWER on and allow

at least 2 hours for the unit to dry out.

For safe operation and satisfactory performance of

your TV/VCR/DVD, keep the following in mind

when selecting a place for its installation:

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top or bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR/DVD near strong magnetic

fields.

•

TV/VCR

: Description refers to TV/VCR operation (in the

TV/VCR mode).

Avoid moving TV/VCR/DVD to locations where

temperature differences are extreme.

•

DVD-V

: Description refers to playback of DVD video discs

(in the DVD mode).

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

: Description refers to playback of audio CDs

(in the DVD mode).

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

MP3

: Description refers to playback of MP3 discs

(in the DVD mode).

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR/DVD disc loading tray.

•

QUICK

•

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

Do not place anything directly on top of the unit.

•

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

The serial number of this product may be found on the back of the unit. No other TV/VCR/DVD has the same

serial number as yours. You should record the number and other vital information here and retain this book as

a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 5 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

STILL PICTURE . . . . . . . . . . . . . .26

TIME SEARCH . . . . . . . . . . . . . . .39

MARKER SETUP SCREEN . . . . . .39

C IMPORTANT SAFEGUARDS . . . . .2

VERTICAL HOLD CONTROL . . .26

C PRECAUTIONS . . . . . . . . . . . . . . . .4

C SPECIAL PLAYBACK . . . . . . . . . .27

RENTAL PLAYBACK . . . . . . . . . .27

AUTO REPEAT PLAYBACK . . . . .27

SPECIAL PLAYBACK FUNCTION . . .40

REPEAT . . . . . . . . . . . . . . . . . . . . .40

PROGRAM . . . . . . . . . . . . . . . . . . .40

RANDOM PLAYBACK . . . . . . . . .40

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

WARNING . . . . . . . . . . . . . . . . . . . .5

C SEARCH . . . . . . . . . . . . . . . . . . . . .28

ZERO RETURN . . . . . . . . . . . . . . .28

PICTURE SEARCH . . . . . . . . . . . .28

TIME SEARCH . . . . . . . . . . . . . . .28

INDEX SEARCH . . . . . . . . . . . . . .29

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C PLAYING A MP3 DISC . . . . . . . . . .41

MP3 PLAYBACK . . . . . . . . . . . . . .41

REPEAT . . . . . . . . . . . . . . . . . . . . .41

PROGRAM . . . . . . . . . . . . . . . . . . .41

RANDOM PLAYBACK . . . . . . . . .41

C TABLE OF CONTENTS . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . . . . .9

C SPECIAL FEATURES . . . . . . . . . .29

REAL TIME TAPE COUNTER . . .29

AUTO REWIND-EJECT . . . . . . . .29

C CHANGING THE SETTINGS . . . .42

SUBTITLE LANGUAGE . . . . . . . .42

AUDIO LANGUAGE . . . . . . . . . . .42

STEREO SOUND MODE . . . . . . . .42

CAMERA ANGLE . . . . . . . . . . . . .42

BLACK LEVEL SETTING . . . . . . .42

VIRTUAL SURROUND . . . . . . . . .42

C PREPARATION FOR USE . . . . . . .11

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .11

C RECORDING . . . . . . . . . . . . . . . . .30

NORMAL RECORDING . . . . . . . .30

CONNECTING TO EXTERNAL

INPUT JACKS . . . . . . . . . . . . . . . .12

SKIPPING UNWANTED SCENES

DURING RECORDING . . . . . . . . .30

INSTALLING THE BATTERIES . .12

EXTERNAL INPUT MODE . . . . . .12

OTR (One Touch Recording) . . . . . .31

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .31

THE ON-SCREEN INFORMATION . . .43

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS SUCH AS MD

DECK OR DAT DECK (for DVD) .13

C CHANGING THE DVD SETUP

C TIMER . . . . . . . . . . . . . . . . . . . . . .32

ITEMS . . . . . . . . . . . . . . . . . . . . . . .44

AUTOMATIC

TIMER RECORDING . . . . . . . . . .32

LANGUAGE SETTING . . . . . . . . .44

DISPLAY SETTING . . . . . . . . . . . .45

AUDIO SETTINGS . . . . . . . . . . . .45

PARENTAL CONTROL . . . . . . . . .46

INITIALIZE . . . . . . . . . . . . . . . . . .46

CONNECTING TO A DOLBY

DIGITAL DECODER (for DVD) . .14

TIMER PROGRAM EXTENSION .33

TV/VCR SECTION

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . .34

C SET UP FOR USE . . . . . . . . . . . . .15

AUTO RETURN . . . . . . . . . . . . . . .34

SLEEP TIMER . . . . . . . . . . . . . . . .34

SELECTING THE LANGUAGE . .15

C TROUBLESHOOTING GUIDE . . .47

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . . . . .15

C ON SCREEN DISPLAY . . . . . . . . .35

C MAINTENANCE . . . . . . . . . . . . . . .50

DAYLIGHT-SAVING TIME . . . . . .17

CHANNEL SET UP . . . . . . . . . . . .18

DISC HANDLING . . . . . . . . . . . . .50

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .35

C SPECIFICATIONS . . . . . . . . . . . . .51

C ESPAÑOL . . . . . . . . . . . . . . . . . . . .52

C WARRANTY . . . . . . . . . . .Back Cover

DELETING (OR ADDING)

CHANNEL(S) . . . . . . . . . . . . . . . . .18

DVD SECTION

C TV OPERATION . . . . . . . . . . . . . . .19

WATCHING A TV PROGRAM . . .19

DEGAUSSING . . . . . . . . . . . . . . . .19

PICTURE CONTROL . . . . . . . . . . .19

CLOSED CAPTION SYSTEM . . . .20

V-CHIP SET UP . . . . . . . . . . . . . . .21

C ABOUT THE DISCS . . . . . . . . . . . .36

PLAYABLE DISCS . . . . . . . . . . . .36

DISC TYPES . . . . . . . . . . . . . . . . .36

C PLAYING A DISC . . . . . . . . . . . . . .37

BASIC PLAYBACK . . . . . . . . . . . .37

GENERAL FEATURES . . . . . . . . .37

DISC MENU . . . . . . . . . . . . . . . . .37

TITLE MENU . . . . . . . . . . . . . . . . .37

RESUME . . . . . . . . . . . . . . . . . . . .38

PAUSE . . . . . . . . . . . . . . . . . . . . . .38

STEP BY STEP PLAYBACK . . . . .38

C MTS(Multi-Channel Television

sound)SYSTEM . . . . . . . . . . . . . . . .23

CHECKING THE SELECTED

MTS MODE . . . . . . . . . . . . . . . . . .23

MTS RECORDING/MONITOR

MODE . . . . . . . . . . . . . . . . . . . . . .23

SELECTING THE MTS SYSTEM .24

FAST FORWARD/REVERSE

SEARCH . . . . . . . . . . . . . . . . . . . .38

C VIDEO CASSETTE . . . . . . . . . . . . .25

SLOW FORWARD / SLOW

REVERSE . . . . . . . . . . . . . . . . . . . .38

C PLAYBACK . . . . . . . . . . . . . . . . . . .26

NORMAL PLAYBACK . . . . . . . . .26

TRACKING ADJUSTMENT . . . . .26

SLOW MOTION . . . . . . . . . . . . . .26

C SEARCH FUNCTION . . . . . . . . . . .39

TRACK SEARCH . . . . . . . . . . . . .39

TITLE / CHAPTER SEARCH . . . .39

- 6 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

TV/VCR Mode

Hi-Fi system–The Hi-Fi stereo recording system

offers you excellent sound quality with a dynamic

range of 80dB, frequency response from 20Hz to

20kHz and 0.005% wow and flutter.

Rotary 4-head Record/Playback System–Four heads

ensure excellent picture quality and special effects playback.

Index Search–Fast-forwards to start of next recording.

Slow Motion–View recorded program at slower

than normal speed.

Infrared remote control

Trilingual on screen TV/VCR setup display

selectable in English or Spanish or French

Real time counter–This shows the elapsed recording

or playback time in hours, minutes and seconds. The

“–” indication will appear when the tape is rewound

further than the tape counter position “0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

function from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Auto power on and off system–Automatically

turns on the TV/VCR/DVD when you insert the

cassette, turns off after auto-rewind and ejects

when the beginning of the tape is reached.

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

Zero Return–The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

Still–“Freeze” the picture at any time, for close

viewing of a particular scene.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Lets you set the TV/VCR/DVD to

advance the tape by entering the desired playback

time you want to skip.

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts and the Weekly timer allows recording to be

made once a week up to the end of the tape.

•

Auto return–After timer recording is finished, the

TV/VCR/DVD can return to the beginning of the

recording.

•

Smooth mode change–TV/VCR mode DVD

mode automatically changes without control.

Sleep timer–Allows you to have the TV/VCR/DVD

automatically turn off at a desired time.

Timer Program Extension–Allows you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

- 7 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Mode

¡Playback MP3 disc

¡Dolby Digital sound

¡On-screen display

This TV/VCR/DVD can handle Dolby Digital sur-

round sound having 5.1 channels when connected to

a Dolby Digital decoder.

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm the

currently active functions (such as program play-

back), on the TV screen using the remote control.

¡Still/fast/slow/step playback

Various playback modes are available including still

pictures, fast forward/reverse, slow motion and step

frames.

¡Search

Chapter search / Title search / Track search / Time

¡Random playback for audio CD and MP3

This TV/VCR/DVD can shuffle the order of tracks

to play them in random order.

¡Repeat

Chapter / Title / Track / Group / All / A-B

¡Program playback for audio CD and MP3

You can program the order of tracks to play them in

any desired order.

¡Marker

The part designated by user can be called back.

¡Resume Play

User can resume to playback from the part at which

the play was stopped.

¡Virtual Surround

¡Bit rate indication

¡DVD menus in a desired language

You can display DVD menus in a desired language,

if available on a DVD.

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no

input from the TV/VCR/DVD for five minutes in the

stop mode. When the screen saver program is acti-

vated for 15 minutes, the power automatically turns

off.

¡DRC (Dynamic range control)

You can control the range of sound volume.

¡Subtitles in a desired language

You can select a desired language for the display

subtitles, if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound

mode, if different languages and modes are available

on a disc.

¡Parental lock

You can set the control level to limit playback of

discs which may not be suitable for children.

¡Automatic detection of discs

This TV/VCR/DVD automatically detects if the

loaded disc is DVD, audio CD or MP3 on disc.

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this TV/VCR/DVD, please be aware that the code num-

ber given may not operate this TV/VCR/DVD. In this case, please call the manufacturer of the universal

remote control.

- 8 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- TV/VCR/DVD FRONT PANEL - [Fig.1]

DVD buttons

TV/VCR buttons

SKIP

PLAY

SKIP

STOP

OPEN/CLOSE

SELECT

CHANNEL

REC/OTR

REW

PLAY

F.FWD

STOP/EJECT

POWER

VOLUME

HEADPHONE VIDEO

AUDIO

DVD

TV/VCR

3 4

8 9 10 11 12 13 14 4 15 16 17 18 19 20 21

5.STOP Button [TV/VCR P.26 / DVD P.37]

Stops operation of the disc. (or front panel)

Stops operation of the disc or tape contents.

(remote control)

[Fig. 2]

- REMOTE CONTROL -

6.OPEN/CLOSE Button [DVD P.37]

Press to insert discs into or remove them from the

tray.

7.Disc loading tray

8.DVD Indicator

Lights on during DVD mode.

POWER PICTURE SLEEP SELECT

CH.

PAUSE

+100

9.SELECT Button

VOL.

Press to change to TV/VCR mode, external input

mode or DVD mode.

+10

SPEED C.RESET

V.SURR

MUTE

10.TV/VCR Indicator

Lights on during TV/VCR mode.

PLAY

STOP

3 (DVD)

15 (TV/VCR)

(DVD) 3

^(TV/VCR)4¹⁴

11. CHANNEL (CH.) K/L Buttons

Press to select memorized channel.

DISC

RECORD

12. Recording Indicator

Flashes during recording. Lights up in the Stand-

by mode for Timer Recording.

DISPLAY

SETUP

ENTER

TITLE

RETURN

13. REC/OTR Button (Front Panel) [TV/VCR P.30, 31]

Press to start manual recording. Press repeatedly

to start One Touch Recording.

RECORD Button (Remote Control) [TV/VCR P.30]

Press to start manual recording.

14. REW Button (for TV/VCR) [TV/VCR P.26]

Press to rewind the tape, or to view the picture

rapidly in reverse during playback mode. (Rewind

Search)

CLEAR SEARCH MODE REPEAT

A-B

AUDIO SUBTITLE ANGLE

MODE

15. F.FWD Button (for TV/VCR) [TV/VCR P.26]

Press to rapidly advance the tape, or to view the

picture rapidly in forward during playback mode.

(Forward Search)

1.POWER Button [TV/VCR P.15 / DVD P.37]

Press to turn the power on and off.

16. STOP/EJECT Button [TV/VCR P.28]

2.VOLUME (VOL.) X/Y Buttons

Press to control the volume level for the DVD and TV.

3.SKIP (SEARCH) Buttons (for DVD)[P.38]

Press once to skip chapters or tracks to a desired

point.

Press and hold to change forward or reverse play-

back speed.

Press to stop the tape motion. Press in the Stop

mode to remove tape from the TV/VCR/DVD.

17. Remote sensor window

18. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

19. VIDEO input Jack

4.PLAY Button [TV/VCR P.26 / DVD P.37]

Starts playback of the disc or tape contents.

Connect to the video output jack of a video

camera or VCR.

- 9 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

- TV/VCR/DVD REAR PANEL - [Fig.3]

ANT.

AUDIO OUT

COAXIAL

20. AUDIO L/R input Jacks

31. MODE Button [DVD P.41]

Connect to the audio output jacks of a video

camera or VCR.

Activates program playback or random playback mode.

32. SEARCH MODE Button [DVD P.39]

21. Cassette compartment

Press to locate a desired point.

22. PICTURE Button

33. AUDIO Button [DVD P.42]

Press to select a desired audio language or sound

mode.

Press to adjust the picture.

23. Number Buttons

34. SUBTITLE Button [DVD P.42]

TV Mode:[P.15]

Press two digits to directly access the desired

channel.

Remember to press a "0" before a single digit

channel.

+100 Button–

Press to select cable channels which are equal or

greater than number 100.

DVD Mode:

Press to enter the desired number.

+10 Button–

Press to enter the desired numbers which are

equal or greater than number 10.

Press to select a desired subtitle language.

35. REPEAT Button [DVD P.42]

Repeats playback of the current disc, title, chapter

or track.

36. ANGLE Button (DVD mode) [DVD P.42]

Press to change the camera angle to see the

sequence being played back from a different angle.

37. A-B REPEAT Button [DVD P.40]

Repeats playback of a selected section.

38. RETURN Button

Returns to the previous operation in the DVD

setup mode.

24. PAUSE Button [TV/VCR P.26 / DVD P.38]

39. ENTER Button

Pauses the current disc or tape operation.

Press to accept a setting.

25. SPEED Button [TV/VCR P.30]

Press to choose the desired recording speed:

SP/SLP.

26. C.RESET Button [TV/VCR P.28]

Press to reset counter to 0:00:00.

Press to cancel a setting of timer program. (See

page 33.)

40. Arrow Buttons

TV/VCR Mode:

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

DVD Mode:

Use when making settings while watching the

display on a TV screen.

27. DISPLAY Button

TV/VCR Mode:

41. DISC MENU Button [DVD P.37]

Display the counter or the current channel number

and current time on the TV screen.

DVD Mode:[P.43]

Displays the current status on the TV screen for

checking purposes.

Displays the menus in the DVD.

42. V. SURR (VIRTUAL SURROUND) Button [DVD P.42]

Sets virtual surround on/off.

43. MUTE Button

Mutes the sound. Press it again to resume sound.

28. SETUP Button [TV/VCR P.15] [DVD P.44-46]

Press to enter or exit the TV menu or DVD setup

mode.

44. SLEEP Button [TV/VCR P.34]

Sets the Sleep Timer.

45. SELECT Button

29. TITLE Button [DVD P.37]

Press to switch TV/VCR and DVD mode. You can

see the mode (TV/VCR or DVD) on the front

panel indicator.

Displays the title menu.

30. CLEAR Button

Resets a setting.

- 10 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

46. ANT. in Jack

48. COAXIAL digital audio out Jack

Connect to the digital input of an external

amplifier or decoder for DVD audio only.

Connect to an antenna, cable system, or satellite

system.

47. Power cord

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook to

avoid breaking a wire before you connect

to a standard AC outlet.

PREPARATION FOR USE

ANTENNA/CABLE CONNECTION

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box (Not supplied)

OUT

From Cable System or

Satellite Dish

VHF Antenna (Not supplied)

75-ohm

Coaxial

Cable

UHF Antenna

(Not supplied)

From Cable

System

(Not sup-

plied)

ANT.

UDIO OUT

COAXIAL

AUDIO OUT

COAXIAL

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not

supplied)

[Fig. 4]

Flat twin-lead cable

VHF/UHF SEPARATE ANTENNAS

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

In some areas it will be necessary to use an outdoor

antenna.

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in the illustration.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR/DVD Remote Control. Unattended timer

recording is limited to one channel at a time.

Use this connection if your cable system connects

directly to your TV/VCR/DVD without a converter

box.

By using this connection you can:

1) Use the TV/VCR/DVD remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

Antenna/Cable Connections

Continued on the Next Page.

NOTE: This TV/VCR/DVD will ONLY record and

view the same channel.

- 11 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TO RECORD A SCRAMBLED/UNSCRAM-

BLED CHANNEL

INSTALLING THE BATTERIES

1. Set the TV/VCR/DVD channel selector to the out-

put channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

Note to CATV system installer:

3)Replace the cover.

This reminder is provided to call the CATV sys-

tem installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper ground-

ing and in particular, specifies that the cable

ground shall be connected to the grounding sys-

tem of the building as close to the point of cable

entry as practical.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO L/R IN/

CONNECTING TO EXTERNAL

INPUT JACKS

When you watch a program recorded on an another

source (VCR or video camera), use the audio/video

input jacks on the front of the TV/VCR/DVD.

Connect the audio/video output jacks of another

source to the AUDIO L/R and VIDEO jacks of this

TV/VCR/DVD.

AUX

VIDEO IN jacks of your

TV/VCR/DVD. Then press the

CHANNEL button K or L until

“AUX” appears on the screen.

Then press the CHANNEL button K or L until

"AUX" appears on the screen.

NOTE:

When you connect a monaural VCR (another

•

source) to this TV/VCR/DVD, connect the Audio

output jack of the monaural VCR (another source)

to the AUDIO L jack of this TV/VCR/DVD. The

audio will output in both L and R channel equally.

To the audio

output jacks

[Another source]

HEADPHONE

VIDEO

L-AUDIO-R

Audio/Video

coaxial cable

(not supplied)

etc.

To the video

[Front of the

TV/VCR/DVD]

output jack

[Fig. 5]

- 12 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)

Use an audio coaxial digital cable available at retail for the audio connections.

Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

ANT.

AUDIO OUT

COAXIAL

Amplifier equipped with digital

To DIGITAL AUDIO OUT

input jacks, MD deck,

(PCM/BITSTREAM)

DAT deck, etc.

COAXIAL jack

(only DVD AUDIO OUT)

To COAXIAL DIGITAL

AUDIO INPUT jack

[Fig. 6]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/VCR/DVD.

Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/VCR/DVD using incorrect set-

tings may generate noise distortion and may also damage the speakers.

•

- 13 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If using this TV/VCR/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the

TV/VCR/DVD outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hook-

ing the TV/VCR/DVD up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience

with powerful and high-quality surround sound as enjoyed in movie theaters.

Use audio coaxial digital cables available at retail for the audio connections.

Center

speaker

ANT.

AUDIO OUT

COAXIAL

Front speaker

(left)

Front speaker

(right)

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

Dolby Digital

decoder

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 7]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/VCR/DVD.

If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.

(See page 45 to set DOLBY DIGITAL to ON.)

•

Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup

mode. Playing a TV/VCR/DVD using incorrect settings may generate noise distortion and may also damage

the speakers.

•

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

- 14 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TV/VCR SECTION

SET UP FOR USE

SELECTING THE LANGUAGE

CLOCK SET UP

(AUTO / MANUAL)

TV/VCR

1 Plug in the TV/VCR/DVD power cord

Plug the TV/VCR/DVD power cord into a

standard AC outlet.

The TV/VCR/DVD clock must be set correctly before

VCR timer recording is possible. It is suggested that

the clock be set manually when first setting up the

TV/VCR/DVD, then set to [ON] the auto clock set-

ting which will periodically correct the setting if nec-

essary.

NOTE: If you cannot receive a station with time

signals, auto clock setting cannot be performed. Use

manual setting only.

NOTE:

If any digits appear in the corner of the

screen, press the POWER button without unplug-

ging the power cord.

•

Make sure ...

Press the SELECT button to select TV/VCR mode or

make sure TV/VCR lights on.

•

MANUAL CLOCK SETTING

Press the POWER button to turn on the TV/VCR/DVD.

NOTE: This function effects only the language on

the screen menu and not the audio source.

•

Make sure ...

The TV/VCR/DVD is turned on.

•

In the example below, the clock is to be set to:

2 Select “LANGUAGE”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “LANGUAGE”.

– M E N U –

DATE

May 6th, 2004

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

SETTING TIME 5:40PM

1 Select “SETTING CLOCK”

Press the SETUP button on the

remote control.

ZERO RETURN

TIME SEARCH

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

3 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Select “ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the ENTER button.

Press the Arrow button K or L to

point to “SETTING CLOCK”.

Then press the ENTER button.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

2 Select “MANUAL CLOCK SET”

Press the Arrow button K or L to

point to “MANUAL CLOCK

SET”.

4 Exit the Language mode

– SETTING CLOCK –

Press the SETUP button on the remote control to

return to TV mode.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

NOTE: If for some reason the menu is in Spanish or

French, press the SETUP button on the remote control,

press the Arrow button K or L to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then

press the ENTER button, then press the SETUP button

on the remote control.

[OFF]

Then press the ENTER button.

3 Select the month

Press the Arrow button K or

– MANUAL CLOCK SET –

MONTH DAY YEAR

until your desired month appears.

0 5

– – – – – – – – –

(Example: May → 05)

HOUR

– –

MINUTE

– – – –

Then press the Arrow button B.

(Or press the Arrow button { to

go back one step.)

4 Select the day

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the Arrow button K or

until your desired day appears.

0 5

0 6 – – – – – – –

(Example: 6th → 06)

Then press the Arrow button B.

HOUR

– –

MINUTE

– – – –

- 15 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTOMATIC CLOCK SETTING

Make sure ...

5 Select the year

– MANUAL CLOCK SET –

MONTH DAY YEAR

The TV/VCR/DVD is turned on.

Confirm the TV/VCR/DVD is receiving a RF

•

Press the Arrow button K or

0 5

0 6 THU 2 0 0 4

until your desired year appears.

(Example: 2004)

Then press the Arrow button B.

(Radio Frequency) signal from either an antenna or

cable system connection using the ANT. terminal

on the rear of the TV/VCR/DVD.

NOTE:

HOUR

– –

MINUTE

– – – –

If a cable converter box is being used, make sure it

is powered on.

You must use the TV/VCR/DVD remote control to

perform the clock setting procedure.

6 Select the hour

– MANUAL CLOCK SET –

MONTH DAY YEAR

•

Press the Arrow button K or

0 5

0 6 THU 2 0 0 4

until your desired hour appears.

(Example: 5, PM)

Then press the Arrow button B.

•

HOUR

0 5

MINUTE

– – PM

If the TV/VCR/DVD is connected directly to a

•

cable converter box or satellite box, the local PBS

station must be selected on the cable box itself and

the TV/VCR/DVD must be set to the output chan-

nel of the cable converter box or satellite box (usu-

ally channel 3 or 4), to be able to set up or correct

the clock automatically.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the Arrow button K or

until the desired minute appears.

(Example: 40)

0 5

0 6 THU 2 0 0 4

HOUR

0 5

MINUTE

4 0 PM

1 Select “SETTING CLOCK”

– M E N U –

8 Start the clock

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the SETUP button on the

5:40 PM

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

select “SETTING CLOCK”.

Press the ENTER button to enter

“SETTING CLOCK” menu.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Although seconds are not displayed,

they begin counting from 00 when

you press the SETUP button on the

remote control. Use this feature to synchronize the

clock with the correct time.

TIME SEARCH

2 Set “AUTO CLOCK” to [ON]

Press the Arrow button B until

“AUTO CLOCK [ON]” appears.

– SETTING CLOCK –

NOTE:

AUTO CLOCK

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

[ 02 ]

[OFF]

TO CHANGE CLOCK SETTING

If you want to change the clock,

1) Follow steps [1] and [2].

2) Select where you want to change using the Arrow

button B.

3) Enter correct numbers using the Arrow button

3 Begin “AUTO CLOCK CH SEARCH”

Press the Arrow button K or L to

– SETTING CLOCK –

select “AUTO CLOCK CH

SEARCH”.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

Press the ENTER button.

The TV/VCR/DVD is now

searching for the station which contain the auto

clock set signal. The search for a signal may take

up to 20 seconds per channel.

•

or L.

4) Press the SETUP button on the remote control to

start the clock.

– AUTO CLOCK CH SEARCH –

“_ _” appears at the lower left of

the screen when the search has

ended.

Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

•

PLEASE NOTE:

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the ENTER button to turn [OFF] this function.

Then you can manually adjust the clock.

_ _

station(s) in your area. See step [4] on page 17.

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 15.

•

Press the SETUP button to exit the screen.

- 16 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE: During Auto Clock CH Search, the picture

may be distorted, this is normal.

DAYLIGHT-SAVING TIME

TV/VCR

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the SETUP button on the remote control.

Select this feature and the TV/VCR/DVD’s clock

automatically will advance one hour in April, then

reverse one hour in October.

Press the Arrow button K or L to

select “SETTING CLOCK”.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the ENTER button to enter

“SETTING CLOCK” menu.

Press the Arrow button K or L to

select “AUTO CLOCK CH”.

Press the ENTER button or the

Arrow button { or B until you

locate Auto Clock Set station num-

ber. See step [3] on page 16.

Press the SETUP button to exit the

screen.

First Sunday of April : At 2 AM the clock imme-

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

– SETTING CLOCK –

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

•

AUTO CLOCK

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[

45]

Make sure ...

[OFF]

Press the POWER button to turn on the TV/VCR/DVD.

•

1 Select “SETTING CLOCK”

– M E N U –

Press the SETUP button on the

TIMER PROGRAMMING

PICTURE CONTROL

5 Turn off the TV/VCR/DVD

Once the TV/VCR/DVD is turned off , it will period-

ically check and set the correct date and time.

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the Arrow button K or L to

point to “SETTING CLOCK”.

Then press the ENTER button.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the Arrow button K or L to

– SETTING CLOCK –

point to “D.S.T.”.

Then press the ENTER button until

[ON] appears.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[ON]

3 Exit the Daylight-Saving Time mode

Press the SETUP button on the remote control to

return to TV mode.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

ENTER button.

- 17 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

DELETING (OR ADDING)

CHANNEL(S)

CHANNEL SET UP

TV/VCR

You can program the tuner to scan all the channels

you receive in your area.

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

NOTE: Channel memory programming is NOT

needed when connected to a cable box or satellite

box. Just select the TV/VCR/DVD channel selector

to the output channel of the cable box or satellite box

(Ex CH3), then select the channel to be viewed on

the Cable Box or Satellite Box.

1 Select “CHANNEL SET UP”

– M E N U –

Press the SETUP button on the

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the Arrow button K or L to

point to “CHANNEL SET UP”.

Then press the ENTER button.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Make sure ...

Press the POWER button to turn on the TV/VCR/DVD.

TIME SEARCH

•

1 Select “CHANNEL SET UP”

2 Select “ADD/DELETE CH”

Press the Arrow button K or L to

point to “ADD/DELETE CH”.

Press the ENTER button.

– CHANNEL SET UP –

– M E N U –

Press the SETUP button on the

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the Arrow button K or L to

point to “CHANNEL SET UP”.

Then press the ENTER button.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

3 Enter the desired channel number

Press the Arrow button K or

until your desired channel number

appears. (You can also use the

number buttons or the CHANNEL

button K or L to enter it)

2 Begin auto ch programming

Press the Arrow button K or L to

point to “AUTO CH PROGRAM-

MING”.

Then press the ENTER button.

The tuner scans and memorizes all

the active channels in your area.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

ADD / DELETE

(Example: CH8)

You must precede single-digit channel numbers

with a zero (Example: 02 ... 09).

•

When selecting cable channels which are higher

than 99, press the +100 button first, then press the

last two digits. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

3 After scanning

•

The tuner stops on the lowest memorized channel.

•

When AUTO CH PROGRAMMING is activated

where there is no TV signal input, “NO TV SIG-

NALS” will appear on the display after the com-

pletion of the channel scanning.

4 Delete (or add) it from (into) memory

Press the ENTER button. The channel number

changes to light red. The channel is deleted from

memory.

To delete another channel, repeat steps [3] and [4].

If you press the ENTER button again, the channel

The TV/VCR/DVD may recognize TV channels to

•

be CATV channels by the receiving conditions. In

this case, try auto ch programming again in the fine

receiving conditions.

•

is memorized again.

Added channel: Light blue.

Deleted channel: Light red.

5 Exit the channel setup mode

Press the SETUP button on the remote control to

return to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL button K or L.

- 18 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

TV/VCR

The TV/VCR/DVD’s picture controls – BRIGHT,

CONTRAST, COLOR, TINT and SHARPNESS –

are preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a more natural looking image.

1 Turn on the TV/VCR/DVD

Press the POWER button to turn on the

TV/VCR/DVD.

NOTES:

2 Select the channel number

Press the CHANNEL button K or L to select your

desired channel number or press the number on the

remote control.

Note for using the Number button on the remote

control:

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

¡You must procede single-digit channel numbers

with a zero (For example: 02, 03, 04 and so on).

¡When selecting cable channels which are higher

than 99, press +100 first, then press the last two

digits. (Example: to select channel 125, first press

“+100” then press “2” and “5”).

TV/VCR/DVD power must be turned on.

•

1 Select “PICTURE CONTROL”

Press the PICTURE button on the remote control.

Remember: If the TV/VCR/DVD is connected to a

cable box or satellite box, the TV/VCR/DVD must

be on CH3 or CH4, then the channel to be viewed

must be selected on the cable box or satellite box.

2 Select item you want to adjust

Press the Arrow button K or L until desired control

is displayed.

BRIGHT

CONTRAST

COLOR

TINT

3 Adjust sound

Press the VOLUME button X or

BRIGHT

–

P +

to adjust the volume.

SHARPNESS

VOLUME 20

3 Adjust the picture control

NOTES:

Press the Arrow button s or B to adjust to your

If you press the CHANNEL button K or L in the

DVD mode, you can change the TV channels.

Even if you turn off the TV/VCR/DVD in the

DVD mode, when you turn it on again, it will go

into the TV/VCR mode.

•

desired level.

Arrow Button

{

Arrow Button

to decrease

brightness

to increase

brightness

BRIGHT

to increase

contrast

to decrease

contrast

CONTRAST

DEGAUSSING

to pale

to purple

to soft

to brilliant

to green

COLOR

TINT

TV/VCR

Magnetism from nearby appliances and speakers

might affect the color of the TV picture.

to clear

SHAPNESS

If there is a power failure of any kind, the

TV/VCR/DVD will retain its memory for this fea-

ture.

•

If this happens, move this TV/VCR/DVD away from

the appliance. If the color is still not correct, unplug

the power cord, then plug it in again 30 minutes later

or so.

- 19 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOSED CAPTION SYSTEM

- TV/VCR SETUP -

1 Select “CAPTION”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “CAPTION”.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/VCR

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

TIME SEARCH

INDEX SEARCH

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

2 Select your desired caption menu

- TV/VCR SETUP -

Press the ENTER button until your

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

desired caption menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

3 Exit the caption setting mode

NOTE:

Press the SETUP button on the remote control to

return to TV mode.

Not all programs are broadcast with closed captions.

Your TV/VCR/DVD is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], select [OFF] using the

ENTER button. Press the SETUP button on the

remote control to return to TV mode.

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

WHEN THE CLOSED CAPTION MODE

IS ON

The On-Screen Display will disappear after 5 sec-

onds.

It will also disappear when the MUTE button is

pressed and when the PAUSE button is pressed

while recording.

ghosts or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

NOTE:

•

If the TV/VCR/DVD displays a

black box on the TV screen, this

means that the TV/VCR/DVD is

set to the TEXT mode. To clear

screen, select [CAPTION1], [CAP-

TION2] or [OFF].

•

If there is a power failure of any kind, the

TV/VCR/DVD will retain its memory for this fea-

ture.

•

Make sure ...

TV/VCR/DVD’s power must be turned on.

•

- 20 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

V-CHIP SET UP SUB RATINGS

When you select the ratings of TV-Y7,TV-PG,TV-14

or TV-MA you will have the option of selecting sub

rating categories.

V-CHIP SET UP

TV/VCR

V-CHIP SET UP

- TV/VCR SETUP -

1 Select “V-CHIP SET UP”

Make sure ...

•

TIMER PROGRAMMING

SETTING CLOCK

Press the SETUP button on the

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/VCR/DVD is turned on.

Press the Arrow button K or L to

select “V-CHIP SET UP”. Then

press the ENTER button.

TIME SEARCH

INDEX SEARCH

1 Select “V-CHIP SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

select “V-CHIP SET UP”.

Then press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

2 Enter Access code

ACCESS CODE

TIME SEARCH

INDEX SEARCH

Use the number buttons on the

remote control to enter the access

code. (Default code is 0000.)

2 Enter Access code

Use the number buttons on the remote

control to enter the access code.

ACCESS CODE

– V-CHIP SET UP –

3 Select “TV RATING”

Press the Arrow button K or L to

select “TV RATING”.

B TV RATING

MPAA RATING

CHANGE CODE

For the first time set-up or in the

•

event the TV/VCR/DVD has lost

power, enter the default code of

the numbers: 0000.

Then press the ENTER button.

– V-CHIP SET UP –

4 Selecting “Sub-Ratings”

Press the Arrow button L to select the sub-rating you

3 Select “TV RATING”

Press the Arrow button K or L to

select “TV RATING”.

B TV RATING

MPAA RATING

CHANGE CODE

wish to block. Then, press the ENTER button twice.

When you select [TV-Y7]:

•

Then press the ENTER button.

TV–Y7

[BLOCK]

Press the Arrow button L or K to

select “FV” (Fantasy Violence).

Then press the ENTER button to

select [BLOCK] or [VIEW].

When you select [TV-PG], [TV-

14] or [TV-MA]:

4 Blocking TV programs

Press the Arrow button K or L to

select “TV rating” that you wish to

block.

Press the ENTER button to turn it

[BLOCK].

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

(

)

[VIEW]

)

•

(

TV–PG

[BLOCK]

Press the Arrow button L or K to

select “D”(Suggestive Dialog),

“L”(Coarse Language),

When you select the rating category and turn it

•

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

“S”(Sexual Situation), or “V”(Violence). Then

press the ENTER button to select [BLOCK] or

[VIEW].

When you turn “TV-Y” to [VIEW], all ratings will

turn to [VIEW] automatically.

•

Note: When you select [TV-MA], “D” does not

appear on the TV screen.

The sub-ratings which set to

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

[VIEW]

[BLOCK] appears next to the rat-

ing category in the TV rating

menu.

[BLOCK]

TV-Y7

TV-G

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

enter the setting and exit the screen.

TV-MA Mature audience only

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

exit the screen.

- 21 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING V-CHIP BLOCKED PRO-

GRAMMING

Note: To change the rating, the TV must be turned to

a station that is not protected. If the (PROTECTED)

appears on the screen, please change the channel to a

station that is not protected.

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

exit the screen.

1)Follow steps [1] and [2].

CHANGE ACCESS CODE

2)Press the Arrow button K or L to select "TV RAT-

ING". Then press the ENTER button. Select a TV

rating to be unblocked by pressing the Arrow but-

ton K or L.

Then press the ENTER button to unblock the rating.

3)Press the SETUP button on the remote control to

exit the screen.

To change access code, follow the steps.

1 Select “V-CHIP SET UP”

Press the SETUP button on the remote control.

Press the Arrow button K or L to select “V-CHIP

SET UP”.

Then press the ENTER button.

MPAA RATING SET UP

2 Enter Access code

ACCESS CODE

- TV/VCR SETUP -

Use the number buttons on the remote

1 Select “V-CHIP SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

select “V-CHIP SET UP”. Then

press the ENTER button.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

control to enter the access code.

The default code is 0000.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

– V-CHIP SET UP –

3 Select “CHANGE CODE”

Press the Arrow button K or L to

select "CHANGE CODE". Then

press the ENTER button.

TV RATING

MPAA RATING

B CHANGE CODE

2 Enter Access code

Use the number buttons on the

remote control to enter the access

code.

ACCESS CODE

4 Enter New code

NEW CODE

Use the number buttons to enter

your desired access code in the

NEW CODE space. Then enter the

same code in the CONFIRM

CODE space. V-CHIP SET UP

screen appear on the screen.

X X X X

CONFIRM CODE

– V-CHIP SET UP –

3 Select “MPAA RATING”

Press the Arrow button K or L to

point to “MPAA RATING”.

Then press the ENTER button.

TV RATING

B MPAA RATING

CHANGE CODE

If you enter wrong code, repeat step 4, making

sure you enter the same new code exactly in the

confirm code space.

•

4 Select your desired item

Press the Arrow button K or L to

point to your desired item.

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

Then press the ENTER button to

select [BLOCK] or [VIEW].

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

exit the screen.

Selection

Rating Category Explanations

General Audience

Note: If you unplug the power cord or power failure

occurs, the changed access code will be lost and will

return to default (0000). Change your access code

again as necessary.

PG-13

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

NC-17

Mature audience only

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “G” to [VIEW], all ratings will turn

to [VIEW] automatically.

•

- 22 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

MTS(Multi-Channel Television sound)SYSTEM

You can record or listen to a program in MTS stereo.

CHECKING THE SELECTED MTS MODE

TV/VCR

When you play a VHS tape, or receive a broadcast

on the TV/VCR/DVD tuner channel you are watching,

the status shown below will appear when you press

the DISPLAY button on the remote control.

1) When a program is broadcast in stereo, STEREO

appears on the TV screen.

2) When a program is broadcast in second audio,

SAP appears on the TV screen.

3) When a program broadcast both in stereo and sec-

ond audio, STEREO and SAP appear on the TV

screen.

NOTE: Although a program may be broadcast in

both stereo and second audio, you cannot

record in both stereo and second audio at

the same time.

PLAY

HIFI

12:00AM

CH 123

STEREO/SAP

4) While the TV/VCR/DVD is set in HIFI stereo

mode and playback mode. HIFI appears on the

TV screen. While the TV/VCR/DVD is set in

monaural(MONO) mode, HIFI disappears from

the TV screen.

COUNT

0:00:00

Second Audio Program, which means your

program, can also be received in a second

language or sometimes a radio station.

SAP

NOTE: If you play non-HIFI tapes while the

TV/VCR/DVD is set in HIFI, HIFI will

disappear from the TV screen and the

TV/VCR/DVD will play automatically in

monaural.

High Fidelity which produces better sound

than standard stereo TV/VCR/DVDs.

HIFI

MTS RECORDING/MONITOR MODE

TV/VCR

Type of broadcast Display on

STEREO/SAP

Hi-Fi audio track(2-channel) Normal audio

the TV screen SELECTION

L-channel

R-channel

track

Regular

-None-

-Invalid-

Mono

(monaural audio)

Stereo broadcast

Bilingual broadcast

STEREO

SAP

-Invalid-

STEREO*

L+R

Main audio

program

Main audio

program

Main audio

program

SAP*

Sub audio

program

Sub audio

program

Sub audio

program

Stereo & Bilingual

broadcast

STEREO

SAP

STEREO*

SAP*

L+R

sub audio

program

sub audio

program

sub audio

program

*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.

- 23 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECTING THE MTS SYSTEM

TV/VCR

Make sure ...

TV/VCR/DVD power must be turned on.

TO SELECT MONO MODE

•

You can change the selection to “MONO” if you

want to listen to HIFI tapes in normal audio play-

back.

TO SELECT HIFI MODE

1) Press the SETUP button on the remote control.

1 Select “USER’S SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “USER’S SET UP”. Then

press the ENTER button.

- TV/VCR SETUP -

Press the Arrow button K or L to point to “USER’S

SET UP”. Then press the ENTER button.

2) Press the Arrow button K or L to point to

“VCR AUDIO”.

3) Press the ENTER button until [MONO] appears.

4) Press the SETUP button on the remote control to

return to TV mode.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2 Select“VCR AUDIO”

Press the Arrow button K or L to

point to“VCR AUDIO”.

– USER’S SET UP –

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

TO SELECT STEREO, SAP, OR MONO

1 Select “USER’S SET UP”

- TV/VCR SETUP -

Press the SETUP button on the

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

remote control.

Press the Arrow button K or L to

point to “USER’S SET UP”.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

3 Select [HIFI]

Press the ENTER button until

[HIFI] appears.

– USER’S SET UP –

INDEX SEARCH

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

– USER’S SET UP –

2 Select “TV AUDIO”

Press the Arrow button K or L to

point to“TV AUDIO”.

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

4 To return to TV mode

Press the SETUP button on the remote control to

return to TV mode.

3 Select [STEREO], [SAP], or [MONO]

Press the ENTER button until [STEREO], [SAP], or

[MONO] appears.

NOTES:

Normally “HIFI” should be selected for playback

•

with HIFI sound.

When you play non-HIFI tapes, the TV/VCR/DVD

will play automatically in the monaural mode.

The TV/VCR/DVD records automatically MTS

broadcasts in HIFI stereo sound unless you select

SAP mode recording before you begin recording.

•

4 To return to TV mode

Press the SETUP button on the remote control to

return to TV mode.

•

NOTES:

You must select the recording mode,either TV

•

AUDIO [STEREO] or [SAP] when you record a

broadcast.

“MTS RECORDING/MONITOR

Refer to

MODE”.

If you select second audio when second audio is

not available, the TV/VCR/DVD will record nor-

mal audio.

The TV/VCR/DVD records automatically MTS

broadcasts in HIFI stereo sound unless you select

SAP mode recording before you begin recording.

•

- 24 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CASSETTE

This TV/VCR/DVD will operate with any cassette that has the

mark. For best results,

we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR/DVD. The

TV/VCR/DVD will automatically turn on.

•

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR/DVD, wait until the tape has

warmed to room temperature and the moisture has

evaporated.

Window

Avoid extreme heat, high humidity and magnetic

fields.

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

TWO DIFFERENT TAPE SPEEDS

REMOVING A CASSETTE

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

1)In the Stop mode, press the STOP/EJECT button

on the TV/VCR/DVD. The cassette will eject.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

ERASE PREVENTION

Note: You can play back a tape recorded in LP mode

(Long Play).

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

If you decide to record on

the tape again, cover the

hole with plastic tape.

Plastic Tape

NOTE:

• In DVD mode, Whether the cassette is with tab or

without tab you insert, it doesn’t start playing until

you press the PLAY button.

In TV/VCR mode, if the cassette without tab is

inserted, playback will automatically start.

- 25 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

NORMAL PLAYBACK

SLOW MOTION

TV/VCR

Press the PAUSE button, then press the F.FWD

Make sure ...

button to start the playback in slow motion. The

TV/VCR/DVD power must be turned on.

•

TV/VCR/DVD mutes the sound during slow motion.

Press the PLAY button to return to normal playback.

NOTE: If it is left in the Slow mode for more than

five minutes, the TV/VCR/DVD will automatically

go into the Stop mode.

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR/DVD will start playback automatically.

STILL PICTURE

PLAY

2 To begin playback

Press the PLAY button.

TV/VCR

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE button

during playback. Only tapes recorded in the SLP

mode will show the least amount of lines. Press the

PLAY button to return to playback.

3 To stop playback

STOP

NOTES:

Press the STOP button when play-

back is completed.

You can advance the picture one frame at a time by

•

pressing the PAUSE button during the Still mode.

If it is left in the Pause mode for more than five

minutes, the TV/VCR/DVD will automatically

switch to the Stop mode.

•

NOTES:

If you press the PLAY button (of the TV/VCR side)

in the DVD mode, you can start the VCR playback.

If you press the SELECT button during the VCR

playback, it will stop and the mode will change to

the DVD mode. In addition, the same function

operates with the DVD side PLAY button or the

OPEN/CLOSE button.

•

VERTICAL HOLD CONTROL

•

TV/VCR

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL button K or L.

NOTE:

If there are video noise lines on the screen, see Tracking

Adjustment section.

TRACKING ADJUSTMENT

TV/VCR

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

However when playing pre-recorded tapes or tapes

•

recorded on other VCR, noise lines (black and

white streaks) may appear on the playback picture.

If this occurs, you can adjust the tracking control

manually by pressing the CHANNEL button K or

L until the streaks disappear. To return to the DTR

function, stop the tape once and start playback

again.

You can reduce the noise lines by pressing the

•

CHANNEL button K or L in slow mode too.

Tracking adjustment in Slow mode will not be set

automatically.

- 26 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

Make sure ...

AUTO REPEAT PLAYBACK

TV/VCR/DVD’s power must be turned on.

Insert a prerecorded tape.

•

TV/VCR

The TV/VCR/DVD has the auto repeat function that

allows you to repeat a tape indefinitely without

touching the PLAY button.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

RENTAL PLAYBACK

TV/VCR

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

Press the SETUP button on the

CHANNEL SET UP

- TV/VCR SETUP -

1 Select “USER’S SET UP”

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

remote control.

Press the SETUP button on the

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the Arrow button K or L to

point to “USER’S SET UP”.

Then press the ENTER button.

remote control.

INDEX SEARCH

Press the Arrow button K or L to

point to “USER’S SET UP”.

Then press the ENTER button.

INDEX SEARCH

2 Set “RENTAL” to [ON]

Press the Arrow button K or L to

point to “RENTAL”.

Press the ENTER button until [ON]

appears.

USER’S SET UP

–

RENTAL

[ON]

2 Select “ALL” or “BLANK”

Press the Arrow button K or L to

point to “REPEAT PLAY”.

USER’S SET UP

–

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[ALL]

[OFF]

[HIFI]

[STEREO]

Press the ENTER button repeatedly

until your desired selection [ALL]

or [BLANK] appears.

3 Exit the Rental setting

Press the SETUP button on the remote control to

return to the TV mode.

3 Exit the Repeat Play setting

Press the SETUP button on the remote control to

return to the TV mode.

4 Start playback

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR/DVD.

4 Start playback

Press the PLAY button to start the Repeat Play.

“REPEAT PLAY B” appears.

•

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR/DVD.

•

TO CANCEL THE RENTAL MODE

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

Repeat steps [1] and [2], select [OFF] using the

ENTER button on the remote control. Press the

SETUP button on the remote control to return to TV

mode.

If there is a power failure of any kind, the

tv/vcr/dvd will retain its memory for this feature.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps [1] and [2], select [OFF] using the

ENTER button on the remote control. Press the

SETUP button on the remote control to return to TV

mode.

If there is a power failure of any kind, the

TV/VCR/DVD will retain its memory for this fea-

ture.

- 27 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

Make sure ...

TIME SEARCH

TV/VCR/DVD power must be turned on.

•

Insert a tape.

•

TV/VCR

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

ZERO RETURN

TV/VCR

This function allows you to search easily a beginning point

that you want to review by rewinding or fast forwarding.

NOTES:

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

This function will not operate in recording mode.

This function is not operative when a cassette tape

is not inserted in the TV/VCR/DVD.

In the example below: To watch a program before/

after 2 hour 50 minutes from the present position, in

either direction.

NOTE:

•

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

•

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

2 Reset the counter to 0:00:00

Press the C.RESET button repeatedly.

1 Insert a tape

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

2 Select “TIME SEARCH” mode

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “TIME SEARCH”.

Then press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

4 To activate “ZERO RETURN” mode

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

- TV/VCR SETUP -

Press the SETUP button on the

TIMER PROGRAMMING

SETTING CLOCK

TIME SEARCH

remote control.

Press the Arrow button K or L to

point to “ZERO RETURN”.

Then press the ENTER button.

CHANNEL SET UP

INDEX SEARCH

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

3 Enter your desired time

Press the Arrow button K or L until

your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

The counter will appear on the TV screen.

The tape will automatically stop when the counter

returns to 0:00:00.

TIME SEARCH

2 : 50

PICTURE SEARCH

If you wish to cancel the Time

Search at this point, press the SETUP button on the

remote control.

TV/VCR

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD g or REW h button during play-

back. (in the SP / LP / SLP modes)

4 Begin Time Search

By pressing the Arrow button s or B, the

TV/VCR/DVD will rewind or fast forward to the

specified point.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

NOTE:

If you press the F.FWD

or REW

button

•

on the front panel in the DVD mode, the VCR for-

ward or reverse will start. Please press the STOP /

EJECT button once to stop it, twice to eject it.

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/VCR/DVD

or the STOP button on the remote control. This will

delete the selected time.

2)Press it again and the TV/VCR/DVD will now search

in super high speed. (in the LP / SLP modes only)

NOTE:

•

Tapes recorded in the SP or LP mode will dis-

play a noise bar on the TV screen and the picture

may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

- 28 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX SEARCH

1 Select “INDEX SEARCH”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “INDEX SEARCH”. Then

press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/VCR

This feature provides a method of indexing the start-

ing point so that it can be easily returned to in either

fast forward or rewind mode.

TIME SEARCH

INDEX SEARCH

The index mark will be made automatically when

•

the RECORD button is pressed. It will also be

marked at the starting point of Timer recording and

OTR.

2 Enter your desired number

Press the Arrow button K or L until

the number of programs that you

want to skip appears.

INDEX SEARCH

0 3

The index mark will not be recorded if the PAUSE

button is pressed and released during recording.

The time gap between making the index marks on

the tape should be greater than 1 minute for SP

recording, 2 minutes for LP recording and 3 min-

utes for SLP recording.

•

(Example: “03” for 3 programs)

•

The Index Search mode will be

canceled if the procedures are not activated in 30

seconds.

•

In some cases, the index mark at the beginning of

video tape cannot be detected.

•

3 Begin Index Search

Press the Arrow button s or B. The TV/VCR/DVD

begins rewinding or fast forwarding to the beginning

of desired program.

NOTE: Every time an index signal is skipped, the

number in the program indicator decreases by one.

Example: You are watching program number 4 and

want to fast forward to program number 7. You

must skip three programs.

CURRENT PLAYBACK PROGRAM

Beginning of tape

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7

End of tape

4 After Index Search

When the preset program is reached, the

TV/VCR/DVD will start playback automatically.

A video cassette must be inserted in the

TV/VCR/DVD for this function to work.

•

INDEX MARK

The number of Index Searches can be set up to 20.

This function will not operate in the recording mode.

When you want to cancel the Index Search while

in progress, press the STOP button.

•

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

TV/VCR

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR/DVD will eject the tape and

turn itself to off.

•

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.)The “–” indication will appear when the tape has

rewound further than “0:00:00” on the tape counter.

This function is operative when Repeat Play is set

to the [OFF] position.

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

•

- 29 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Make sure ...

TV/VCR/DVD power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTES:

This TV/VCR/DVD will ONLY record and view the same channel.

This TV/VCR/DVD cannot record the contents from the built-in DVD.

•

SKIPPING UNWANTED

NORMAL RECORDING

SCENES DURING RECORDING

TV/VCR

You can ONLY watch the same TV program that is

being recorded.

Press the PAUSE button to tem-

PAUSE

porarily stop recording.

Press the PAUSE or RECORD but-

ton to resume recording.

NOTES:

1 Select the channel to be recorded

CH 10

Press the number buttons on the

remote control or the CHANNEL

button K or L.

Remember: If the TV/VCR/DVD

is connected to a cable box or satel-

lite box, the TV/VCR/DVD must be on CH3 or CH4,

then the channel to be recorded must be selected on

the cable box or satellite box.

After five minutes, the

TV/VCR/DVD will automatically switch to the

Recording mode to prevent tape damage.

•

If “CLOSED CAPTION (ON)” is selected, the On-

Screen Display will appear for 5 seconds, then dis-

appear.

•

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

REC

3 Begin recording

Press the RECORD button.

4 Stop recording

Press the STOP button when recording is completed.

- 30 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

Push(es) Display

1 push

Recording length

(normal recording)

OTR (One Touch Recording)

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

TV/VCR

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/VCR/DVD.

17 pushes

8:00

480 minutes

Make sure ...

TV/VCR/DVD power must be turned on.

Insert a cassette tape with its erase prevention tab in

place. (If necessary, rewind or fast forward the tape

to the point at which you want to begin recording.)

NOTES:

You cannot start OTR with the remote control.

Recording starts immediately when the REC/OTR

button is pressed.

•

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

•

TV/VCR

You can make copies of video tapes made by friends

or relatives for your enjoyment.

You can not copy a DVD to a videotape.

•

When the REC/OTR button is pressed 18 times, the

TV/VCR/DVD returns to the Normal Recording mode.

To stop the OTR operation, press the STOP button

on the TV/VCR/DVD or on the remote control.

•

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

•

Connect your TV/VCR/DVD and a Source (Playing)

VCR using the following diagram.

To show the remaining time, press the DISPLAY

•

button on the remote control so that “OTR”

appears on the TV screen. (It will show up

momentarily then disappear.)

[Fig.8]

[The TV/VCR/DVD]

Recording stops when 0:00 is reached.

•

REW

PLAY

F.FWD

STOP/EJECT

HEADPHONE VIDEO

AUDIO

Please note that in the SLP mode maximum record-

ing time, assuming the tape is started at the begin-

ning, is 8 hours using T-160 (or 6 hours using T-120).

If the tape runs out before the end time, the

TV/VCR/DVD will switch to the Stop mode

immediately, ejects the tape and turns itself off.

•

[Ex: Source (playing)

VCR or camcorder]

If you press the POWER button during OTR, the

TV/VCR/DVD continues recording until the select-

ed length is reached.

•

AUDIO

Audio/Video

adapter cable

(not supplied)

OUT

VIDEO

OUT

1 Select the channel to be recorded

Press the number buttons on the remote control or

the CHANNEL button K or L.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record over, into the TV/VCR/DVD’s cassette

compartment.

3)Press the SPEED button on remote control for the

TV/VCR/DVD to select the desired recording

speed (SP/SLP).

4)Press the CHANNEL button K or L on the

TV/VCR/DVD until “AUX” appears on the screen.

5)Press the RECORD button on the TV/VCR/DVD.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during copying, use the

TV/VCR/DVD’s front panel controls whenever pos-

sible. The remote control might affect the source

(Playing) VCR’s playback operation.

Remember: If the TV/VCR/DVD is connected to a

cable box or satellite box, the TV/VCR/DVD must

be on CH3 or CH4, then the channel to be recorded

is selected on the cable box or satellite box.

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

3 Begin OTR

Press the REC/OTR button on the

OTR(2 : 30)

TV/VCR/DVD as many times as

needed. The recording length will be

determined by the number of times

you press the REC/OTR button. Each

7)To stop copying, press the STOP/EJECT button on

the TV/VCR/DVD, then stop the tape on the

source VCR or camcorder.

additional push will increase the

recording time by 30 minutes. It is set up to 8 hours.

- 31 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER

AUTOMATIC TIMER

RECORDING

1 Select “TIMER PROGRAMMING”

- TV/VCR SETUP -

Press the SETUP button on the

remote control.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

TV/VCR

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Confirm “TIMER PROGRAM-

MING” is pointed by pressing the

Arrow button K, and press the

ENTER button.

You may set the TV/VCR/DVD to start and end a

recording while you are away. You can set 8 pro-

grams to record on specific days, daily or weekly

within a 1 year period.

TIME SEARCH

INDEX SEARCH

If you have not yet set the clock, “MANUAL

CLOCK SET” appears. If so, follow steps [3] to

[8] on pages 15-17. Then set the timer recording.

In the example below, the timer is being set to record:

•

DATE:

July 4th, 2004

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL:

TAPE SPEED:

CH61

2 Select your desired program

position (1~8)

Press the Arrow button K or L to

select the desired program position.

Then press the Arrow button B.

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Make sure ...

- - -/- - - - - -:- -

-:- - - -

If a cable box or satellite box is connected with the

TV/VCR/DVD you will be limited to record only one

channel, and the channel selector on the

•

TV/VCR/DVD must be selected to the output channel

of the boxes CH 3 or CH 4 and then the actual chan-

nel to be recorded must be selected on the boxes.

Clock must be set to the correct time and date

before setting the timer.

TV/VCR/DVD power must be turn on to program it.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

3 Set the channel number

Press the Arrow button K or L until

the desired channel number

appears. (Example: CH61)

Then press the Arrow button B.

Remember: If the TV/VCR/DVD

is connected to a cable box or satellite box, the

TV/VCR/DVD must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box or

satellite box.

– TIMER PROGRAMMING –

CH DATE BEGIN END

•

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

•

The channel you want to record is properly set in

advance. (See page 18.)

•

Avoid over lap of programs ...

There is a chance that a program will not be record-

ed, when programs overlap;

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

CH DATE

BEGIN END

Press the Arrow button K (up)

until the desired date appears.

(Example: “7/04” for July 4th).

Then press the Arrow button B.

- - -/- - - - - -:- -

61 7/04 SUN -:- -

- - -/- - - - - -:- -

-:- - - -

The illustration below demonstrates the sequence

of recordings.

•

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

For every day recording : To record a TV program

at the same time on the same channel every day.

(Example: Monday through Sunday)

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Recording Sequence

Press the Arrow button L (down)

until “EVRY DAY” appears.

Then press the Arrow button B.

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

For weekly recording : To record a TV program at

9:00AM

10:00AM

11:00AM

12:00PM

the same time on the same channel every week.

*Recording period is SHADED

(Example: every Monday)

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Press the Arrow button L (down)

until “EVRY” and your desired

day of the week appear together.

Then press the Arrow button B.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

- 32 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER PROGRAM EXTENSION

5 Set beginning hour

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the Arrow button K or L until

the desired hour appears.

- - -/- - - - - -:- -

-:- - - -

TV/VCR

61 7/04 SUN 7:12^P

- - -/- - - - - -:- -

(Example: “ 7, PM” for 7:30PM)

Then press the Arrow button B.

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

2)Repeat step [1] on page 32.

6 Set beginning minute

3)Press the RECORD button and select the desired

program using the Arrow button K or L.

4)Press the RECORD button again.

Press the Arrow button K or L until

the desired minute appears.

- - -/- - - - - -:- -

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

(Example: “30” for 7:30PM)

Then press the Arrow button B.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the PAUSE but-

ton on the remote control. The recording time

returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

7 Set end hour

Press the Arrow button K or L until

the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then press the Arrow button B.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

8:30^PM- -

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

Press the Arrow button K or

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

5)Press the ENTER or RETURN button to exit the

setting menu. Then press the SETUP button on the

remote control to return to original mode.

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

until the desired minute appears.

(Example: “50” for 8:50PM)

Then press the Arrow button B.

TO CORRECT A PROGRAM

9 Set the tape speed

Press the Arrow button K or

until the desired tape speed

appears. (Example: SP)

While setting a program; press the Arrow button

s to go back one step and enter the correct num-

bers using the Arrow button K or L.

After setting a program;

•

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

•

1)Press the POWER button.

2)Repeat steps [1] - [2] on page 32.

3)Press the Arrow button B (or press the Arrow

button s to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the Arrow button K or L.

4)Press the POWER button to set automatic timer

recording.

10 Finish setting the program

Press the ENTER or RETURN button. The program

is now completed.

To set another program, repeat steps [2] to [10].

Press the SETUP button on the remote control to

•

return to original mode.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

11 Set the timer

Press the POWER button to set automatic timer

recording. The RECORDING indicator lights up.

After setting a program;

1)Press the POWER button.

•

You must turn off the TV/VCR/DVD to activate

automatic timer recording.

•

2)Repeat steps [1] ~ [2] on page 32 and select a

program you want to cancel.

3)Press the C.RESET button.

4)Press the SETUP button on the remote control to

return to TV mode.

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

While recording is in progress;

•

1)Press the POWER button.

2)Press the STOP/EJECT button on the

TV/VCR/DVD.

- 33 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the Recording

indicator goes off.

2)Press the SETUP button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the ENTER button. The details of programs

appear on the TV screen.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/VCR/DVD will rewind to the beginning of the

recorded program(s).

NOTE:

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

•

5)Press the SETUP button on the remote control to

return to TV mode.

4 Watch the recorded program

Press the PLAY button.

HINTS FOR AUTOMATIC

TIMER RECORDING

TO CANCEL THE AUTO RETURN

MODE

TV/VCR

Repeat steps [1] and [2], select [OFF] using the

ENTER button.

Make sure the channel you want to record is prop-

erly set in advance.

•

If there is a power failure of any kind, the

TV/VCR/DVD will retain its memory for this fea-

ture.

It is not necessary to press the RECORD button for

timer recording.

Recording begins automatically at the Start time.

The display will not be turned on when the programmed

recording begins. To watch the currently recorded TV

program or to play a DVD disc, press the POWER but-

ton to turn on the display and use the SELECT button to

choose the TV/VCR mode or the DVD mode.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette will

be ejected when the POWER button is pressed to off.

If the tape runs out before the end time, the

TV/VCR/DVD will switch to the Stop mode

immediately and the tape will be ejected.

•

SLEEP TIMER

TV/VCR

The Sleep Timer function turns off the

TV/VCR/DVD without using the POWER button

after a desired period of time.

NOTE:

•

This function does not operate during Recording

mode.

•

1 Select “SLEEP TIMER”

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears.

AUTO RETURN

TV/VCR

2 Set sleep time

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

Press the SLEEP button until your

desired sleep time appears.

Each additional push will increase

the time by 30 minutes up to 120

minutes.

After 5 seconds, exit the Sleep Timer setting.

SLEEP 120 MINUTES

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

Press the SETUP button on the

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

remote control.

Press the Arrow button K or L to

point to “USER’S SET UP”.

Then press the ENTER button.

TO CANCEL THE SLEEP TIMER

INDEX SEARCH

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears. Press the SLEEP button

until “SLEEP 0 MINUTES” appears.

2 Set “AUTO RETURN” to [ON]

Press the Arrow button K or L to

point to “AUTO RETURN”.

Press the ENTER button until [ON]

appears.

USER’S SET UP

–

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[ON]

[HIFI]

[STEREO]

- 34 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

When the Closed Caption mode is OFF:

When the Closed Caption mode is ON:

Counter mode: After 5 seconds, only the counter

remains. To clear it, press the DISPLAY button.

Clock mode: After 5 seconds, only the clock and

the channel number remain. To clear them, press

the DISPLAY button.

The On Screen Display disappear after 5 seconds.

This is true even if the MUTE button is pressed or

the PAUSE button is pressed while recording.

•

OFF mode

Clock/Counter mode

OFF mode Counter mode

Clock mode

STOP

5:40PM

CH2

STOP

5:40 PM

CH2

COUNT 0:12:34

After 5 seconds

5:40PM

CH2

COUNT 0:12:34

Counter

remains

Clock & Channel

remains

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 35 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS

DISC TYPES

The following discs can be played back on this

TV/VCR/DVD.

[

]

DVD

Data on a DVD is divided into sections called "titles" and

then into subsections called "chapters", each of which is

given a title or chapter number. Playback conditions are

preset on some DVD video discs and these playback con-

ditions take priority over user operations on this

TV/VCR/DVD. If a function you selected does not run as

desired, refer to the manual accompanying the disc.

DVD video

DVD+R/RW*

CD-R/RW*

DVD-R/RW*

Audio CD

MP3*

* Depending on the types or the writing method of the

medium some discs can not be played.

Example

• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs

made on personal computers or on DVD recorders may

not be played back properly due to the factors such as

scratches, dirt or special properties of the disc.

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

• Discs made on personal computers may not be played

back properly due to the different environment or the

settings of the application you use. We recommend

always to use the standardized, rightly formatted discs.

(Please contact the sales agency for more detail).

[

]

AUDIO CD

This TV/VCR/DVD conforms to the NTSC color system.

You cannot play discs recorded in other color systems

such as PAL or SECAM.

Data on an audio CD is divided into sections called

“tracks”, each of which is given a track number.

¡Some discs include region codes as shown below.

Example

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

¡The number inside the symbol refers to a region of the

world, and a disc encoded in a specific region format

can only be played back on TV/VCR/DVD with the

same region code.

The following discs cannot be played back on this

TV/VCR/DVD.

[

]

MP3

Data on an MP3 is divided into sections called "groups",

and then into subsections called "tracks", each of which is

given a group or track number.

DVD with region codes other than 1 or ALL.

DVD-ROM

Example

Group 1

Group 2

DVD-RAM (Never play back, otherwise malfunc-

tion may result.)

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

CD-ROM

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-I (Never play back, otherwise malfunction

may result.)

SACD

Photo CD (Never play back, otherwise malfunc-

tion may result.)

Video CD (Never play back, otherwise malfunc-

tion may result.)

Any other discs without compatibility indications.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING A DISC

BASIC PLAYBACK

GENERAL FEATURES

DVD-V

MP3

DVD-V

VD may contain menus to navigate the disc and

Getting started

access special features. Press the appropriate number

buttons or use the Arrow button (K/L/s/B) to high-

light your selection in the DVD main menu and press

the ENTER button to confirm.

¡Turn on the power of amplifier and any other com-

ponents, if necessary.

Press the POWER button.

¡The power will turn on.

NOTES

¡Select DVD mode by pressing the SELECT button on

the remote control. Then operate the DVD functions.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

Press the OPEN/CLOSE button to open disc

loading tray.

Place the chosen disc in the tray, with the

label facing up.

DISC MENU

DVD-V

Press the DISC MENU button.

¡The DVD main menu will appear.

If the feature is not available,

may appear on the TV screen.

symbol

Press the PLAY button.

¡The tray will close automatically and playback will

then start from the first chapter or track of the disc.

If the playback does not start automatically, press

the PLAY button.

If disc menu is available on the disc, audio lan-

guage, subtitle options, chapters for the title

and other options will appear for selection.

¡When you playback a DVD which features a title

menu, it may appear on the screen. In this case, refer

to “TITLE MENU”.

Press the Arrow button (K/L/s/B) to

select an item and the ENTER button to

confirm selection.

Press the STOP button to stop playback.

TITLE MENU

DVD-V

NOTES

¡When the DVD mode has been switched to the

TV/VCR mode, the DVD mode shuts down first and

then TV picture and sound appears in about 4 seconds.

Similarly, when the POWER button is pressed to turn

off in the DVD mode, this mode shuts down first and

then the TV/VCR/DVD’s power is turned off.

¡A “prohibited icon” may appear at

the top-right on the TV screen dur-

ing operation, warning that a pro-

hibited operation has been encoun-

tered by the DVD or the disc.

¡With DVDs that use titles for playback program sig-

nals, playback may start from the second title, or it

may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

Press the TITLE button.

¡The title menu will appear.

If the feature is not available,

may appear on the TV screen.

symbol

Press the Arrow button (K/L/s/B) to

select an item and the ENTER button to

confirm selection.

CALLING UP A MENU SCREEN

DURING PLAYBACK

For DVD-Vs

¡Press the DISC MENU button to call up the DVD menu.

¡Press the TITLE button to call up the title menu.

NOTE

¡Contents of menus and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

FAST FORWARD/REVERSE

RESUME

DVD-V

MP3

DVD-V

MP3

During playback, press the STOP button.

¡Resume message will appear on the TV screen.

During playback, press and hold the g or

h button for a few seconds.

¡“ g 1” or “h 1” appears on the screen.

Press the PLAY button, playback will resume

from the point at which playback was stopped.

To select another speed, repeat step1 until

your required speed appears on the screen.

¡To cancel resume, press the STOP button twice.

¡If TV/VCR/DVD is turned off, resume function will

be cancelled.

¡For MP3, playback will resume from the beginning

of the track at which playback was stopped.

¡For DVDs, fast forward/reverse search speed is dif-

ferent depending on the disc. Approximate speed is

1(×2), 2(×8), 3(×50) and 4(×100).

¡For audio CDs, approximate speed is ×16.

¡For MP3, approximate speed is ×8

¡When you use buttons on the TV/VCR/DVD front

panel, use the SKIP G/ SEARCH g or

SKIP H/ SEARCH h button.

PAUSE

DVD-V

MP3

To return to normal playback, press the

PLAY button.

During playback, press the PAUSE button.

¡Playback will pause and sound will be muted.

To continue playback, press the PLAY button.

SLOW FORWARD /

SLOW REVERSE

STEP BY STEP PLAYBACK

DVD-V

During playback, press the PAUSE button.

¡Playback will pause and sound will be muted.

Press and hold the g or h button for a

few seconds.

¡“

1” or “

1” appears on the screen.

The disc goes forward by one frame each

time the PAUSE button is pressed.

To select another speed, repeat step2 until

your required speed appears on the screen.

To exit step by step playback, press the

PLAY button.

¡Slow forward or reverse speed varies with the disc.

Approximate speed is 1(1/16), 2(1/8) and 3(1/2).

¡When you use buttons on the TV/VCR/DVD front

panel, use the SKIP G / SEARCH g or

SKIP H / SEARCH h button.

To return to normal playback, press the

PLAY button.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

SEARCH FUNCTION

TRACK SEARCH

TIME SEARCH

MP3

DVD-V

There are three ways to begin playback on an Audio

CD and MP3 at a specific track.

During playback, press the SEARCH MODE

button three times (CD: twice) to display the

Time Search on the TV screen.

Using the Number buttons on the remote control

Within 30 seconds, enter a desired disc

time using the Number buttons on the

remote control.

Press the Number buttons to enter the

desired Track number.

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, press 3).

¡Playback will start at the specified time.

¡Press the CLEAR button to erase the incorrect input.

¡When there is no need to enter a number, “0”

appears automatically. For example, “ 0 : 0

appears in the Time Search display if the total time

of the disc is less than 10 minutes.

¡To play track 26, press +10, 2, 6.

”

- -

Using the SEARCH MODE button

MARKER SETUP SCREEN

Press the SEARCH MODE button.

¡The track search display appears.

DVD-V

Within 30 seconds, select a desired track

number using the Number buttons on the

remote control.

Use markers to memorise your favorite places on a

disc.

¡For single digits press 0 first.

¡Playback will start at the selected track.

Press the SEARCH MODE button four times

(CD: three times) during playback.

Using the SKIP

buttons

¡The display screen and Markers will appear on the

TV screen.

During playback, press the SKIP G button to move

the next track. Press it repeatedly to skip subsequent

tracks. Press the SKIP H button to go back to begin-

ning of the current track. Press it repeatedly to go to

the previous tracks.

¡If the SKIP button is pressed while the playback is

paused, the playback will be paused again after skip-

ping to the next track.

Press the Arrow button (s /B) to select 1, 2,

3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “

- - -

” appears in the display.

- - - -

When you reach the desired point, press the

ENTER button.

NOTE

¡The SKIP

¡The Title or Track and elapsed playing time will

appear in the TV screen.

G buttons are not available when

playback is stopped.

To return to the Marker later, press the

SEARCH MODE button four times (CD: three

times) during playback and the Arrow but-

ton (s /B) to choose the desired marker,

then press the ENTER button.

TITLE / CHAPTER SEARCH

DVD-V

Press the SEARCH MODE button once for

the Chapter search, twice for the Title

search during playback.

NOTES

¡Opening the disc tray or turning off the power or

selecting AC at step 2 and pressing the ENTER but-

ton will erase all Markers.

_/2

¡To clear a marker, using the Arrow button (s /B),

position the cursor on to the marker number to be

cleared and press the CLEAR button.

¡You can mark up to 10 points.

Enter the desired chapter/title number using

the Number buttons on the remote control.

¡Playback will start at the selected Chapter or Track.

¡Press the CLEAR button to erase the incorrect input.

¡For single digits press 0 first.

Press the SEARCH MODE or RETURN but-

ton to exit.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK FUNCTION

REPEAT

PROGRAM

REPEAT is available only during playback.

You may determine the order in which tracks will play.

REPEAT TITLE / CHAPTER

DVD-V

In stop mode, press the MODE button.

¡The PROGRAM screen will appear.

To activate the repeat function, press the

REPEAT button during playback.

¡The repeat mode changes as described below every

time you press the button.

Press the Arrow button ▲ or ▼ to select a

track, then press the

TOTAL

CHAPTER

(current chapter repeat) (current title repeat)

TITLE

OFF

(repeat off)

ENTER button.

¡Press the CLEAR button to

erase the most recently entered

program.

NOTES

¡Repeat Title/Chapter is not available with some

scenes.

Repeat step 2 until you have selected all the

tracks you want to play in the program.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

Press the PLAY button to play the pro-

grammed tracks.

REPEAT TRACK

NOTES

¡While the program is being played back, the STOP

works as follows.

To activate the repeat function, press the

REPEAT button during playback.

¡The repeat mode changes as described below every

time you press the button.

¡Press the STOP button once and then the PLAY but-

ton again, playback will restart from the point where

the STOP button was pressed. (Program continued)

¡Press the STOP button twice and then the PLAY button

again, playback will restart from the track in the usual

way. (Program cleared)

TRACK

(current track repeat)

ALL

OFF

(repeat off)

(entire disc repeat)

¡Up to 99 programs can be entered.

¡To erase all programs at once, select ALL CLEAR at

the bottom of the list at Step2.

NOTES

¡If you like to repeat the current track in the program,

press the REPEAT button repeatedly until

TRACK appears during playback. If you like to

repeat the entire program press the REPEAT button

¡Repeat setting will be cleared when moving to other

track.

¡Repeat playback does not function during repeat A-B

playback.

repeatedly until

ALL appears during playback.

REPEAT A-B

RANDOM PLAYBACK

DVD-V CD

Press the REPEAT A-B button at your cho-

sen starting point.

A- appears briefly on the TV screen.

This shuffles the playing order of tracks instead of

playback in the sequence.

In stop mode, press the MODE button twice.

Press the REPEAT A-B button again at your

chosen end point.

¡RANDOM screen appears.

RANDOM

CD-DA

TOTAL 0:45:55

A-B appears briefly on the TV screen and the

repeat sequence begins.

RANDOM PROGRAM

no indication

PLAY

To exit the sequence, press the REPEAT A-

B button.

NOTES

Press the PLAY button to start random playback.

NOTE

¡The repeat A-B section can only be set within the cur-

rent title (for DVDs) or current track (for audio CDs).

¡Repeat A-B is not available with some scenes in DVD.

¡To cancel the A point which was set, press the

CLEAR button.

¡If you like to repeat the current track in the random

selection, press the REPEAT button repeatedly until

TRACK appears during playback. If you like to

repeat the entire random selection press the

REPEAT button repeatedly until

during playback.

¡Repeat A-B playback does not function during title,

chapter, track or all repeat playback.

ALL appears

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING A MP3 DISC

MP3 PLAYBACK

PROGRAM

MP3

This feature allows you to program an MP3 disc to

play in a desired sequence.

When a CD with MP3 files is in the TV/VCR/DVD,

press the DISC MENU button to call up the MP3 menu

on the TV screen.

In stop mode, press the MODE button.

¡The PROGRAM screen will appear.

In stop mode, press the Arrow button (K/L)

to select the desired

Select a desired track using the Arrow but-

ton (K/L/s/B). Then, press the ENTER

button.

group or track.

folder name 1

folder name 2

¡If a group is selected, press

the Arrow button or the

folder name 3

folder name 4

file name 1

file name 2

file name 3

¡Press the Arrow button B when you want to go to

the next hierarchy.

¡Press the Arrow button s when you want to go back

to the previous hierarchy.

¡Press the CLEAR button to erase the most recently

entered program.

ENTER button to go on to the

track selection screen. Press

the Arrow button (^K/L) to

choose a track, then press the ENTER button.

¡If a track is selected, press the ENTER button to start

playing tracks. Starting from the one you’ve just

chosen the subsequent tracks will be played.

folder name 1

Repeat step 2 until you have selected all the

Tracks you want to play in the program.

¡Press the TITLE button to return to the first item.

Press the STOP button to stop playback.

NOTES

Press the PLAY button to start programmed

playback.

¡Folders are known as Groups; files are known as

Tracks.

¡MP3 files are accompanied by

NOTES

¡While the program is being played back, the STOP

button as follows.

icon.

¡Press the STOP button once and then the PLAY but-

ton again, playback will restart from the point where

the STOP button was pressed. (Program continued)

¡Press the STOP button twice and then the PLAY button

again, playback will restart from the track in the usual

way. (Program cleared)

¡Maximum of 255 folders can be recognized.

¡Maximum of 512 files can be recognized.

¡Up to 8 hierarchies can be created.

This TV/VCR/DVD recommends the use of files

recorded at the below specifications:

¡Sampling frequency: 44.1kHz or 48kHz

¡Constant bit rate: 112kbps ~ 320kbps.

¡To erase all programs at once, select ALL CLEAR at

the bottom of the list at Step2.

REPEAT

MP3

RANDOM PLAYBACK

MP3

REPEAT is available only during playback.

In stop mode, press the MODE button twice.

¡RANDOM screen appears.

1 To activate the repeat function, press the

REPEAT button during playback.

¡The repeat mode changes as described below every

time you press the button.

Press the PLAY button to start random play-

back.

TRACK

(current track

repeat)

GROUP

(current group

repeat)

ALL

(entire disc

repeat)

OFF

(repeat off)

NOTE

¡Repeat setting will be cleared when moving to other

track.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE SETTINGS

SUBTITLE LANGUAGE

CAMERA ANGLE

DVD-V

The TV/VCR/DVD allows you to select a language for Some DVD discs contain scenes which have been shot

subtitles during DVD disc (if available) playback. simultaneously from various angles. You can change

the camera angle when the (

screen.

) icon appears on the

Press the SUBTITLE button during playback.

Press the SUBTITLE button repeatedly to

select your desired subtitle language.

Press the ANGLE button during playback.

¡The selected angle will be displayed on the display

¡The subtitle language will appear on the display bar

at the top of the TV screen.

bar at the top of the screen.

Press the ANGLE button repeatedly to

select your desired angle.

To turn off subtitles, press the SUBTITLE

button repeatedly until OFF appears.

NOTES

BLACK LEVEL SETTING

Some discs allow audio language setting/subtitle language

setting on the disc menu. (Operation varies between discs,

so refer to the manual accompanying the disc.)

DVD-V

¡If the desired language is not shown after pressing

the SUBTITLE button several times, the disc does

not have subtitles in that language.

Adjust the Black Level Settings to make the black

parts of the picture brighter.

¡If you choose a Language that has a 3 letter language

code, the code will be displayed every time you

change the Subtitle language setting. If you choose

any other languages, ‘---’ will be displayed instead.

(Refer to page 44.)

Press the MODE button during playback.

OFF

Press the ENTER button to switch OFF.

ON: Makes the dark parts brighter.

AUDIO LANGUAGE

OFF: Shows the original picture as recorded.

DVD-V

The TV/VCR/DVD allows you to select a language

during DVD disc (if multi languages are available)

playback.

Press the MODE button twice or the

RETURN button to exit.

NOTE

¡The setting will be saved even if the TV/VCR/DVD

Press the AUDIO button during playback.

is turned off.

Press the AUDIO button repeatedly to select

your desired language.

VIRTUAL SURROUND

NOTE

DVD-V

MP3

¡Pressing the AUDIO button may not work on some

DVDs with multiple audio languages (e.g. DVDs

which allow audio language setting on the disc menu).

You can enjoy surround-sound effect over two speak-

ers on this TV/VCR/DVD.

STEREO SOUND MODE

Press the V.SURR button once or the MODE

button twice (CD/MP3: once) during play-

back.

OFF

Press the AUDIO button repeatedly during

playback to select between STEREO, L-CH

or R-CH.

Press the ENTER button to set it 1 (Natural

effect) or 2 (Emphasized effect) or OFF.

STEREO - both right and left channels are active (stereo)

L-CH - only left channel is active

R-CH - only right channel is active

Press the V. SURR or RETURN button to

exit.

NOTE

NOTE (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

¡If the Virtual Surround setting is ON, the sound mode

will be fixed to STEREO and can not be changed.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

THE ON-SCREEN INFORMATION

DVD-V

MP3

You can check the information about the current disc by pressing the DISPLAY button on the remote control.

For DVD-Vs

For audio CDs

Press the DISPLAY button during playback

to show current Chapter.

Press the DISPLAY button during playback

to show the current Track.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

9/49

0:00:00 -0:03:30

Press the DISPLAY button again to show

current Total Track.

Press the DISPLAY button again to show

current Title.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

rent title will be displayed.

Press the DISPLAY button again to exit the

display.

Press the DISPLAY button again.

¡The BIT RATE and the current repeat setting will be

displayed.

For MP3

¡If you are playing a dual layered disc, the layer num-

ber will also be displayed (L0: Layer 0 is playing.

L1: Layer 1 is playing).

Press the DISPLAY button during playback.

¡The name of the file currently in play will be dis-

played.

Press the DISPLAY button again to exit the

display.

Press the DISPLAY button again to show

the track number, the elapsed time, the

repeat status and the playback status at the

top of the screen.

will be displayed when repeat play has been

selected.

T - indicates Track repeat

G - indicates Group (folder) repeat

A - indicates Disc repeat

Press the DISPLAY button again to exit the

display.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE DVD SETUP ITEMS

LANGUAGE SETTING

Language

Code Language

Code

DVD-V

A-B

L-N

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali;Bangla

Bhutani

Bihari

Bislama

Breton

4748 Laothian

4747 Latin

4752 Latvian;Lettish

6563 Lingala

4759 Lithuanian

4764 Macedonian

5471 Malagasy

4765 Malay

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

Language options are not available with some discs.

Press the SETUP button twice in STOP

mode so that the DVD SETUP menu

appears.

4771 Malayalam

4772 Maltese

4847 Maori

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

5167 Marathi

4860 Moldavian

5072 Mongolian

4854 Nauru

SETUP

QUICK

CUSTOM

INITIALIZE

4855 Nepali

4864 Norwegian [NOR]

4853

5971 Occitan

4851 Oriya

Oromo(Afan)

5759 Panjabi

4947 Pashto;Pushto

7254 Persian

4961 Polish

5464 Portuguese [POR]

4965 Quechua

5047 Rhaeto-Romance

6058 Romanian [RUM]

5160 Russian [RUS]

5161

5166 Samoan

Sangho

5261 Sanskrit

5256 Scots Gaelic

5255 Serbian

Bulgarian

Burmese

Byelorussian

O-R

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

C-E

Press the Arrow button L to select CUS-

Cambodian

Catalan

TOM, then press the ENTER button.

Chinese [CHI]

Corsican

Croatian

¡CUSTOM mode will appear.

Czech

Press the Arrow button (K/L) to select

“LANGUAGE”, then press the ENTER button

to confirm.

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

SETUP

CUSTOM

F-H

Faroese

Fiji

LANGUAGE

DISPLAY

AUDIO

Finnish [FIN]

French [FRE]

Frisian

PARENTAL

5264 Serbo-Croatian

5271 Sesotho

5358 Setswana

5747 Shona

Galician

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

Press the Arrow button (K/L) to select the

next items, then press the ENTER button.

5051 Sindhi

5158 Singhalese

5758 Siswat

5360 Slovak

AUDIO: Sets the audio language.

Gujarati

Hausa

Hebrew

5367 Slovenian

5447 Somali

5569 Spanish [SPA]

5455 Sundanese

5467 Swahili

SUBTITLE: Sets the subtitle language.

DISC MENU: Sets the language for DVD menu.

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Press the Arrow button (K/L) to select a

setting, then press the ENTER button.

Swedish [SWE]

5565

5560 Tagalog

5547 Tajik

5551 Tamil

5557 Tatar

5347 Telugu

5566 Thai

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

¡If OTHER is selected on the AUDIO, SUBTITLE or

DISC MENU screen, press four-digit number to

enter the code for the desired language. (Refer to the

language code list.)

¡Only the languages supported by the disc can be

selected.

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

5647 Tibetan

5669 Tigrinya

5760 Tonga

5765 Tsonga

5757 Turkish [TUR]

6469 Turkmen

5771 Twi

Kazakh

Press the SETUP button to exit.

Kinyarwanda

Kirghiz

Kirundi

NOTE

6460

U-Z

¡Language Setting for Audio and Subtitle is not avail-

able with some discs. Then use the AUDIO and the

SUBTITLE buttons. Details are on page 42.

Korean [KOR]

Kurdish

5761 Ukrainian

5767 Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

TO CHANGE THE ON-SCREEN MENUS

You can access the TV/VCR SETUP menu by pressing

the SETUP button from the DVD mode. Refer to

“SELECTING THE LANGUAGE” on page 15 to

changing the on-screen menus.

Yoruba

Zulu

If you choose a Language that has a 3 letter language

code, the code will be displayed every time you change

the Audio or Subtitle language setting on page 42. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY SETTING

AUDIO SETTINGS

DVD-V

You can change certain aspects of the DVD display Choose the appropriate Audio settings for your equip-

screens and on-screen messages on the TV screen.

ment as it only affects during the playback of DVD

discs.

Press the SETUP button twice in STOP mode

so that the DVD SETUP menu appears.

Press the SETUP button twice in STOP mode

so that the DVD SETUP menu appears.

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

SETUP

QUICK

CUSTOM

INITIALIZE

QUICK

CUSTOM

INITIALIZE

Press the Arrow button L to select CUS-

TOM, then press the ENTER button.

¡CUSTOM mode will appear.

Press the Arrow button L to select “CUS-

TOM”, then press the ENTER button.

Press the Arrow button (K/L) to select “DIS-

PLAY”, then press the ENTER button to con-

firm.

¡CUSTOM mode will appear.

Press the Arrow button (K/L) to select

“AUDIO”, then press the ENTER button to

confirm.

SETUP

CUSTOM

LANGUAGE

DISPLAY

AUDIO

PARENTAL

SETUP

CUSTOM

LANGUAGE

DISPLAY

AUDIO

Press the Arrow button (K/L) to select the

below items, then press the ENTER button.

PARENTAL

TV MODE:

QUICK

Press the Arrow button (K/L) to select the

below items, then press the ENTER buttons.

¡Press the Arrow button (K/L) for an item selection,

then press the ENTER button.

¡Select 4:3 LETTER BOX for black bars to appear on

top and bottom of the screen.

DRC (Dynamic Range Control):

¡To compress the range of soft to loud sound.

¡The default setting is ON.

¡Select 4:3 PAN & SCAN for a full height picture

with both sides trimmed.

¡The default setting is 4:3 LETTER BOX.

DOWN SAMPLING:

¡Set to ON when outputting in 48 kHz.

¡The default setting is ON.

When playing disc with copyright Protection

¡If you select OFF, copyright protection will be acti-

vated and sound will be down sampled at 48kHz.

STILL MODE

¡Press the Arrow button (K/L) for an item selection,

then press the ENTER button.

¡Select “AUTO” usually.

¡If you select “FIELD”, the picture in the still mode

will be stabilized.

¡If you select “FRAME”, the picture in the still mode

will be highly defined.

DOLBY DIGITAL:

QUICK

ANGLE ICON:

Set to On when the unit is connected to a Dolby Digital

Decoder.

¡Press the ENTER button repeatedly to turn Angle

icon ON or OFF.

(ON: Output a Dolby Digital signal)

(OFF: Convert the Dolby Digital to PCM (2 channel

stereo))

¡The default setting is ON.

AUTO POWER OFF:

¡The default setting is ON.

¡Press the ENTER button repeatedly to turn Auto

Power off ON or OFF.

The default setting is ON and it will turn the TV/

VCR/DVD off automatically after 15 minutes of no use.

Press the SETUP button to exit.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROL LEVELS

PARENTAL CONTROL

ALL

All parental lock is cancelled.

DVD-V

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Parental Control limits the disc viewing that exceed

your settings. (with a password or playback will stop.)

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

Levels 7 to 2

Only DVD software intended for general use and

children can be played back.

PARENTAL LEVEL

Level 1

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

Only DVD software intended for children can be

played back, with those intended for adult and

general use is prohibited.

Press the SETUP button twice in STOP mode

so that the QUICK SETUP menu appears.

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

IF YOU FORGET THE PASSWORD

Press the number buttons 4, 7, 3, 7 at step 4.

Then enter your new password.

Press the Arrow button L to select “CUS-

TOM”, then press the ENTER button.

SETUP

¡Password will be cleared and parental level will be

set to ALL.

QUICK

CUSTOM

INITIALIZE

Proceed the Steps 5-7 again.

Press the Arrow button (K/L) to select

“PARENTAL”, then press the ENTER button.

INITIALIZE

SETUP

CUSTOM

This allows you to return all selections of SETUP

(except for PARENTAL) to their default settings.

LANGUAGE

DISPLAY

AUDIO

PARENTAL

Press the SETUP button twice in STOP

mode so that the INITIALIZE menu appears.

Press the Arrow button (K/L) to select “INI-

TIALIZE”, then press the ENTER button.

Enter your four-digit password then press

the ENTER button.

Select “YES”, then press the ENTER button

twice. All the settings (except for

“PARENTAL”) will be cleared.

Press the Arrow button (K/L) to select

“PARENTAL LEVEL”, then press the ENTER

button.

¡To cancel the initialization, select “NO”.

Press the Arrow button (K/L) to select the

desired level, then press the ENTER button.

Press the SETUP button to exit.

Press the SETUP button to exit

NOTES

¡When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the

password.(in the event you forget the password, see

below)

¡To change the password, press the Arrow button

(K/L) to select CHANGE at step 5, then press the

ENTER button. Enter the four-digit password, then

press the ENTER button.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

¡Record the password in case you forget it.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If the TV/VCR/DVD does not perform properly when operated as instructed in this Owner’s Manual, check

the TV/VCR/DVD, consulting the following checklist.

PROBLEM

CORRECTIVE ACTION

Make sure the power plug is connected to an AC outlet.

Make sure the power is turned on.

Check if the power plug is connected to an AC outlet.

Check the batteries in the remote control.

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote.

You have to be within 23 feet of the TV/VCR/DVD.

No power

•

The TV/VCR/DVD does not

respond to the remote control

•

Check if the correct mode is selected. If not switch the mode by

pressing the SELECT button on the remote control,whichever you need.

TV/VCR Mode

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

PROBLEM

No picture and sound

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Press the SELECT button on the remote control to select TV mode.

Then try other TV feature.

•

Let the TV/VCR/DVD program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust COLOR control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust CONTRAST & BRIGHT control.

•

No picture or poor picture on

TV/VCR/DVD

No sound or poor sound

Bars On Screen

Picture Distorted or Blurred

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Adjust CONTRAST & BRIGHT control.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

Picture OK, Sound Poor

CORRECTIVE ACTION

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR/DVD clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

•

Timer recording is not possible

Cannot go into Record mode

Playback picture is partially noisy

• ^{Adjust tracking control for a better picture using the CHANNEL}

• ^{button K or L on the TV/VCR/DVD.}

• ^{Head cleaning may be necessary. Refer to “AUTO HEAD}

• ^{CLEANING” on page 50.}

No picture but the audio is OK in

playback

No operation by infrared Remote

Control

Video or color fades in and out

• ^{Make sure the AC cord is connected to an AC outlet.}

• ^{Check batteries in remote control.}

• ^{You can not copy a copyrighted video tape. You are experiencing}

when making a copy of a video tape • ^{copy guard protection.}

Different color marks on screen

Magnetism from nearby appliances and geomagnetism might affect

•

the color of the TV picture. Move the

away from the

TV/VCR/DVD

appliances, the

can repair itself automatically. If you

TV/VCR/DVD

want to repair immediately, unplug the power cord, then plug it in

again 30 minutes later or so.

CLOSED CAPTION PROBLEM

My TV/VCR/DVD is showing

captions that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/VCR/DVD will not show

the text dialogue in its entirety or

there is a delay of what is being

said.

• Captions that are delayed a few seconds behind the actual

are common for live broadcast. Most captioning production

• companies can display a dialogue to a maximum of 220 words

• per minute. If a dialogue exceeds that rate, selective editing is used

• to insure that the captions remain up-to-date with the current

• TV screen dialogue.

My captions are scrambled with

white boxes on the TV screen.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Mode

PROBLEM

CORRECTIVE ACTION

• Insert a correct video disc that plays on this TV/VCR/DVD.

• Press the SELECT button on the remote control to select DVD mode.

Then, try other DVD feature.

No picture

• Insert the disc.

Disc cannot be played

• Clean the disc.

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the control level.

• Connect the audio cables firmly.

No sound

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

• This TV/VCR/DVD does not support DTS audio. This is not a mal-

function.

• There are some cases where pictures may be slightly distorted, which

are not a sign of a malfunction.

No DTS audio is output

Distorted picture

• Although pictures may stop for a moment, this is not a malfunction.

Audio or subtitle language

does not match the set up

•

The selected language is not available for audio or subtitles on the DVD.

This is not a malfunction

The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera

angles. This is not a malfunction

Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected

changed

language. This is not a malfunction.

“Prohibited icon” appears on the

screen, prohibiting an operation

CD sound dropout

• That operation is prohibited by this TV/VCR/DVD or the disc.

This is not a malfunction.

• Scratched disc. Replace the disc with an unscratched one.

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

CABINET CLEANING

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-968-3429, to

locate an Authorized Service Center.

NOTES:

Wipe the front panel and other exterior surfaces of

the TV/VCR/DVD with a soft cloth immersed in

lukewarm water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR/DVD. Such chemi-

cals may cause damage and discoloration to the

exposed surfaces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

Should your TV/VCR/DVD become inoperative,

•

do not try to correct the problem by yourself. There

are no user-serviceable parts inside. Turn off,

unplug the power cord and please call our help line

at 1-800-968-3429, to locate an Authorized Service

Center.

Playback picture may become blurred or interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your TV/VCR/DVD may

need to be cleaned.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the TV/VCR/DVD still does not perform properly when it is operated while referring to the relevant sec-

•

tions and to "TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be

dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical

pickup unit.

DISC HANDLING

Use discs which have the following logos on them.

(Optical audio digital discs.)

To clean-off, use a soft cloth.

•

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

ReWritable

Recordable

Do not use detergent or abrasive cleaning agents.

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

Always store the disc in its protective case when it

is not used.

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

TV/VCR

CRT

19 inch in-line gun,

90˚ deflection tube

NTSC-M

OTHER SPECIFICATIONS

Terminals

Television system :

Closed caption system :§15.119/FCC

Antenna input:

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary four-head

1/2 inch

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output:

1/8” stereo (3.5 mm)

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

One pin jack,

500m Vpp (75 ohm)

Digital encoded

Remote control:

#2~#6

#7~#13

#14~#69

infrared light system

Operating

temperature:

5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

Power consumption

VHF :

MID band :

SUPER band :

HYPER band :

A5~A1, A~I

J~W

W+1~W+84

(Maximum):

Picture tube:

Dimensions:

90W

19"

H:19-11/16” (500mm)

W:23-13/16” (605mm)

D:18-11/16” (474mm)

48.5 lbs (22kg)

Weight:

DVD

Product type:

Discs:

DVD Player

DVD video, Audio CD

Output signal format: NTSC color

Designs and specifications are subject to change without notice.

If there is a discrepancy between languages, the default language will be English.

•

–

01A11

Download from Www.Somanuals.com. All Manuals Search And Download.

12. Indicador de grabación

INDICE

Parpadea durante la grabación. Se ilumina durante el

modo de espera de grabación controlada por temporizador.

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52

PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52

MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 52

VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53

CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54

MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54

CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54

CONEXIÓN A UN AMPLIFICADOR ESTÉREO

13. Botón REC/OTR (Panel frontal) [TV/VCR P.30, 31]

Presione para empezar la grabación manual. Presione

repetidamente para empezar la grabación instantánea

(OTR).

Botón RECORD (Manda a distancia) [TV/VCR P.30]

Presione para empezar la grabación manual.

14. Botón REW (para TV/VCR)

Presione este botón para rebobinar la cinta o para ver

la imagen rápidamente en dirección de retroceso

durante el modo de reproducción. (Búsqueda en direc-

ción de retroceso)

EQUIPADO CON TOMAS DE ENTRADA DIGITAL,

PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

15. Botón F.FWD (para TV/VCR)

Presione este botón para adelantar rápidamente la cinta

o para ver la imagen rápidamente en dirección de

avance durante el modo de reproducción. (Búsqueda en

dirección de avance)

SECCIÓN DE TV/VCR

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54

SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 54

AJUSTE DE CANALES . . . . . . . . . . . . . . . . . . . . . . . . . 55

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

16. Botón STOP/EJECT

Presione este botón para detener la cinta. Presiónelo en

el modo de parada para retirar la cinta del

televisor/videograbadora/DVD.

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55

17. Ventanilla del sensor de mando a distancia

18. Toma HEADPHONE

Para conectar auriculares (no suministrados) y escuchar

en privado.

CONTROLES DE

OPERACIÓN Y FUNCIONES

19. Toma de entrada VIDEO

Conecte aquí la toma de salida de vídeo de una

videocámara o de una videograbadora.

PANEL FRONTAL DEL

TELEVISOR/DVD

20. Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

Consulte la figura 1 de la página 9

21. Compartimiento del cassette

22. Botón PICTURE

MANDO A DISTANCIA

Presione este botón para ajustar la imagen.

23. Botones numéricos

Consulte la figura 2 de la página 9

Modo TV:

Presione dos botones para acceder directamente al

canal deseado.

VISTA POSTERIOR

No olvide presionar “0” antes de elegir un canal de un

solo dígito.

Consulte la figura 3 de la página 10

Botón +100

1. Botón POWER

Presione este botón para conectar y desconectar la ali-

mentación.

2. Botones VOLUME X/Y

Presione estos botones para controlar el nivel de volumen

del DVD y el televisor.

Presione este botón para seleccionar canales de tele-

visión por cable cuyo número sea igual o superior a 100.

Modo DVD:

Presione este botón para introducir el número deseado.

Botón +10

Presione este botón para introducir números iguales o

3. Botones SKIP (para DVD)

mayores que 10

Presione el botón correspondiente una vez para omitir

capítulos o pistas y desplazarse a un punto específico.

Mantenga el botón presionado para cambiar la veloci-

dad de reproducción en avance o retroceso.

24. Botón PAUSE

Hace una pausa en la reproducción del disco o cinta.

25. Botón SPEED

Presione este botón para seleccionar la velocidad de

grabación deseada: SP/SLP.

4. Botón PLAY

Inicia la reproducción del contenido del disco o cinta.

5. Botón STOP

Detiene la reproducción del disco.

6. Botón OPEN/CLOSE

Presione este botón para insertar discos en la bandeja o

retirarlos de ella.

26. Botón C.RESET

Presione este botón para poner el contador en 0:00:00.

Presiónelo también para cancelar un ajuste de progra-

ma de temporizador.

27. Botón DISPLAY

Modo TV/VCR:

7. Bandeja de carga del disco

Para visualizar el contador o el número del canal y la

fecha actual en la pantalla del televisor.

Modo DVD:

8. Indicador DVD

Se ilumina durante el modo DVD.

Indica el estado actual en la pantalla del televisor para

fines de comprobación.

9. Botón SELECT

Presione este botón para cambiar al modo TV/VCR,

modo de entrada externa o modo de DVD.

28. Botón SETUP

Presione este botón para activar o salir del modo de

menús de televisor o configuración de DVD.

10. Indicador TV/VCR

Se ilumina durante el modo TV/VCR.

29. Botón TITLE

11. Botones CHANNEL K/L

Para visualizar el menú de títulos.

Utilice estos botones para seleccionar canales memorizados.

–

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

30. Botón CLEAR

ANTENAS SEPARADAS DE VHF/UHF

En algunas zonas será necesario utilizar una antena

exterior.

TELEVISIÓN POR CABLE SIN CAJA DE

CONVERTIDOR/DECODIFICADOR

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su televisor/

videograbadora/DVD, sin una caja de convertidor.

Con esta conexión podrá:

Para cancelar ajustes.

31. Botón MODE

Activa el modo de reproducción programada o el modo de

reproducción aleatoria.

32. Botón SEARCH MODE

Presione este botón para localizar un punto deseado.

33. Botón AUDIO

Presione este botón para seleccionar un idioma de

audio o el modo de sonido deseado.

1) Utilizar el mando a distancia del televisor/

videograbadora/DVD para seleccionar canales.

2) Programar uno o más canales decodificados para

grabación automática controlada por temporizador.

NOTA: Este televisor/videograbadora/DVD SÓLO

puede grabar el canal que se está viendo.

34. Botón SUBTITLE

Presione este botón para seleccionar el idioma de subtí-

tulos deseado.

35. Botón REPEAT

Repite la reproducción del disco, título, capítulo o pista actual.

36. Botón ANGLE (modo DVD)

Presione este botón para cambiar el ángulo de la cámara

y ver la secuencia que se está reproduciendo desde un

ángulo diferente.

TELEVISIÓN POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATÉLITE

37. Botón A-B REPEAT

Si su compañía de televisión por cable le suministra

una caja de convertidor o si utiliza un sistema de

satélite, podrá utilizar la conexión básica que se

muestra en la ilustración.

Repite la reproducción de una sección seleccionada.

38. Botón RETURN

Permite volver a la operación anterior en el modo de

configuración de DVD.

Al utilizar esta conexión, también podrá grabar canales

codificados. Sin embargo, la selección de los canales

deberá hacerse con la caja de convertidor o con la caja

de satélite. Esto significa que no es posible cambiar de

canal utilizando el mando a distancia del televisor/

videograbadora/DVD. La grabación en ausencia (contro-

lada por temporizador) está limitada a un canal a la vez.

PARA GRABAR UN CANAL

39. Botón ENTER

Presione este botón para establecer un ajuste.

40. Botones de flechas

Modo TV/VCR:

Presione estos botones para seleccionar un modo de

ajuste en el menú que aparece en la pantalla del televisor.

Presiónelos también para seleccionar opciones o

establecer ajustes en un menú en particular.

Modo DVD:

CODIFICADO/DECODIFICADO

Use estos botones para hacer ajustes mientras observa

la imagen en la pantalla del televisor.

1.Ajuste el selector de canales del

televisor/videograbadora/DVD al canal de salida de

la caja de convertidor de televisión por cable o caja

de satélite. (Ej., CH3)

41. Botón DISC MENU

Muestra los menús contenidos en el DVD.

42. Botón V.SURR

2.Seleccione el canal que desea grabar en la caja de

convertidor de televisión por cable o caja de satélite.

Activar/desactivar el envolvente virtal.

43. Botón MUTE

Suprime la salida de sonido. Presiónelo de nuevo para

restablecer el sonido.

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención

del instalador de sistemas CATV para que tenga

en cuenta el Artículo 820-40 de la NEC, que pro-

porciona recomendaciones para hacer una conex-

ión a tierra apropiada y, en particular, especifica

que la tierra del cable debe conectarse al sistema

de puesta a tierra del edificio, tan cerca del punto

de entrada del cable como sea posible.

44. Botón SLEEP

Utilice este botón para ajustar el temporizador de dormir.

45. Botón SELECT

Presione este botón para cambiar entre los modos

TV/VCR y DVD. El modo seleccionado (TV/VCR o

DVD) se visualiza en el indicador del panel delantero.

46. Toma de entrada ANT.

Conéctela a una antena, sistema de televisión por cable

o sistema de satélite.

CONEXIÓN A TOMAS DE ENTRADA

EXTERNA

47. Cable de alimentación

Conéctelo a una toma de CA estándar (120 V, /60 Hz).

NOTA: Antes de conectar el cable de alimentación a

una toma de CA estándar, retírelo del gancho

para evitar dañarlo.

Cuando vea un programa grabado en otra fuente (videograbado-

ra o videocámara), utilice las tomas de entrada de audio/vídeo

de la parte delantera del televisor/videograbadora/DVD.

Conecte las tomas de salida de audio/vídeo de otra fuente a

las tomas AUDIO L/R y VIDEO de este televisor/

videograbadora/DVD. Luego, presione los botones CHAN-

NEL K/L hasta que aparezca "AUX" en la pantalla.

NOTA:

48. Toma de salida de audio digital COAXIAL

Conéctela solamente a la entrada digital de un amplifi-

cador externo o decodificador de audio de DVD.

PREPARACIÓN PARA LA

UTILIZACIÓN

CONEXIONES DE ANTENA/CABLE

Cuando conecte una videograbadora monofónica (otra

fuente) a este televisor/videograbadora/DVD, conecte la

toma de salida de audio de la videograbadora monofónica

(otra fuente) a la toma AUDIO L de este

televisor/videograbadora/DVD. El audio saldrá igual-

mente por los canales izquierdo y derecho.

•

Consulte la figura 4 de la página 11

Consulte la figura 5 de la página 12

–

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

Consulte la figura 7 de la página 14

NOTAS:

PARA INSERTAR LAS PILAS

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a

distancia en el sentido de la flecha.

2) Inserte 2 pilas "AA" en el

compartimiento de las pilas, en el

sentido indicado por las marcas de polaridad (+/-).

3) Vuelva a poner la cubierta.

Asegúrese de desconectar la alimentación de todos

los componentes del sistema antes de conectar otro

componente.

Consulte los manuales de instrucciones de los

componentes que va a conectar al televisor/

videograbadora/DVD.

Si conecta un decodificador Dolby Digital, ajuste

la función DOLBY DIGITAL a ON para salida de

audio en el modo de configuración.

A menos que se haga la conexión a un decodifi-

cador Dolby Digital, ajuste la función Dolby

Digital a OFF para salida de audio en el modo de

configuración. La reproducción en un

•

MODO DE ENTRADA EXTERNA

Al usar una señal de entrada externa (otra videograbado-

ra o una videocámara), conecte los cables de salida de

audio/vídeo del equipo externo a las tomas AUDIO L/R

IN/ VIDEO IN de su televisor/videograbadora/DVD.

Luego, presione los botón CHANNEL K o L hasta que

aparezca "AUX" en la pantalla.

televisor/videograbadora/DVD utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede causar daños a los altavoces.

CONEXIÓN A UN AMPLIFICADOR

ESTÉREO EQUIPADO CONTOMAS DE

ENTRADA DIGITAL, PLATINA MD O

PLATINA DAT (Para DVD)

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la D

doble son marcas de fábrica de Dolby

Laboratories.

Utilice un cable digital coaxial de audio de venta en el

comercio especializado para hacer las conexiones de audio.

Conexión a un amplificador equipado con tomas de

entrada digital, platina MD o platina DAT.

SECCIÓN DE TV/VCR

PREPARACIÓN PARA LA

UTILIZACIÓN

Consulte la figura 6 de la página 13

NOTAS:

• La fuente de audio de un disco grabado en formato de

sonido envolvente Dolby Digital de 5,1 canales no se

puede grabar como sonido digital mediante una plati-

SELECCIÓN DE IDIOMA

TV/VCR

• ⁿA^ase^Mgú^Dre^ose^Dd^Ae^Td^.esconectar la alimentación de todos

Enchufe el cordón de alimentación

del televisor/videograbadora/DVD

los componentes del sistema antes de conectar otro

• ^cC^oo^mns^pu^olⁿte^enlo^tes^.manuales de instrucciones de los compo-

nentes que va a conectar al televisor/videograbadora/

televisor/videograbadora/DVD en una toma de CA

Enchufe el cordón de alimentación del

estándar.

• ^DA^Vju^Dst^.e la función Dolby Digital a OFF para salida de

audio en el modo de configuración. La reproducción

en un televisor/videograbadora/DVD utilizando

ajustes incorrectos puede generar ruido y distorsión, y

también puede causar daños a los altavoces.

NOTA:

Si aparecen algunas cifras en la esquina de la pan-

•

talla, pulse el botón POWER sin desenchufar el

cordón de alimentación.

Asegúrese de que ...

Pulse el botón POWER para encender el

televisor/videograbadora/DVD.

•

CONEXIÓN A UN DECODIFICADOR

DOLBY DIGITAL (para DVD)

NOTA: Esta función afecta sólo el idioma en el menú

de la pantalla y no la fuente de audio.

Si utiliza este televisor/videograbadora/DVD para

reproducir un disco DVD grabado en formato de

sonido envolvente Dolby Digital de 5,1 canales, el

televisor/videograbadora/DVD emitirá un flujo de

datos DOLBY DIGITAL desde su toma de salida de

audio digital COAXIAL. Si conecta el reproductor a

un decodificador Dolby Digital, podrá disfrutar de

una tonalidad más convincente y real, con un sonido

envolvente potente y de alta calidad similar al de los

cines.

Seleccione “LANGUAGE”

Pulse el botón SETUP en el mando a distancia.

Pulse el botón K o L para señalar “LANGUAGE”.

Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS”

Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”

con el botón ENTER.

Salga del modo de idioma

Pulse el botón SETUP en el mando a distancia para

volver al modo del televisor.

Utilice cables digitales coaxiales de audio

disponibles en el comercio especializado para hacer

las conexiones de audio.

–

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTA: Si, por alguna razón, el menú está en inglés o

francés, pulse el botón SETUP en el mando a distancia,

pulse el botón K o L para señalar el “LANGUAGE

[ENGLISH]” o “LANGAGE [FRANÇAIS]”, a contin-

uación, pulse el botón ENTER y pulse el botón SETUP

en el mando a distancia.

1)Pulse el botón SETUP en el mando a distancia.

Pulse el botón K o L para indicar “AJUSTE

RELOJ”.

Luego, pulse el botón ENTER.

2)Pulse el botón K o L para indicar “AJUSTE

MANUAL RELOJ”.

Luego, pulse el botón ENTER.

3)Pulse el botón K o L hasta que aparezca el mes

deseado. (Ejemplo: Mayo - 05)

AJUSTE DE CANAL

TV/VCR

Luego, pulse el botón B.

Puede programar el sintonizador para buscar todos

los canales que recibe en su localidad.

4)Pulse el botón K o L hasta que aparezca el día

del mes deseado. (Ejemplo: 6 - 06)

Luego, pulse el botón B.

5)Pulse el botón K o L hasta que aparezca el año

deseado. (Ejemplo: 2004)

Luego, pulse el botón B.

6)Pulse el botón K o L hasta que aparezca la hora

deseada. (Ejemplo: 5, PM)

NOTA: El canal preparado NO es necesario cuando

esté conectado a una caja de cable o caja de satélite.

Sólo tiene que seleccionar con el selector de canal

del televisor/videograbadora/DVD al canal de salida

de la caja de cabe o caja de satélite (por ejemplo el

canal CH3). Seleccione el canal a ver en la caja de

cable o caja de satélite.

Luego, pulse el botón B.

Asegúrese de que ...

7)Pulse el botón K o L hasta que aparezca el minu-

to deseado. (Ejemplo: 40)

Pulse el botón POWER para encender el televi-

sor/videograbadora/DVD.

•

8)Pulse el botón SETUP en el mando a distancia.

Aunque los segundos no se visualizan, éstos

empiezan a contar desde 00 cuando se pulsa

SETUP en el mando a distancia. Utilice esta fun-

ción para sincronizar el reloj con la hora correcta.

1 Seleccione “AJUSTE DE CANAL”

Pulse el botón SETUP en el mando a distancia.

Pulse el botón K o L para señalar “AJUSTE DE

CANAL”.

A continuación, pulse el botón ENTER.

2 Empiece el prefijado automático

Pulse el botón K o L para señalar “AUTOPROGRA-

MACION DE CA”.

SECCIÓN DE DVD

A continuación, pulse el botón ENTER.

El sintonizador busca y memoriza todos los canales

activos en su localidad.

REPRODUCCIÓN BÁSICA

DVD-V

MP3

3 Después de buscar

El sintonizador se detiene en el canal memorizado

más bajo.

Para empezar

¡Conecte la alimentación del amplificador y otros

componentes, si es necesario.

Cuando se activa AUTOPROGRAMACION DE

•

CA, donde no hay entrada de señal del televisor,

aparecerá “NO HAY SEÑAL DE TV” en la pan-

talla después de terminar la búsqueda de canales.

Presione el botón POWER.

¡La alimentación se conectará.

Presione el botón OPEN/CLOSE para abrir

la bandeja de carga del disco.

El televisor/videograbadora/DVD puede reconocer

•

los canales de TV para que sean canales de TV de

antena de cable con las condiciones de recepción.

En este caso, pruebe nuevamente con el prefijado

automático en las condiciones de recepción fina.

Ponga el disco deseado en la bandeja, con

la etiqueta hacia arriba.

Presione el botón PLAY.

¡La bandeja se cerrará automáticamente y la repro-

ducción comenzará desde el primer capítulo o pista

del disco. Si la reproducción no comienza automáti-

camente, presione el botón PLAY.

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú podrá aparecer en la pan-

talla.

AJUSTE DEL RELOJ

TV/VCR

Cerciórese...

La alimentación del televisor/videograbadora/DVD

deberá estar conectada.

•

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 6 de mayo de 2004

HORA: 5:40 PM

Presione el botón STOP para detener la

reproducción.

–

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of

original retail purchase.

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE

RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH

THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI

AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,

please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-968-3429

http://www.funai-corp.com

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in China

1EMN20035

T0003UD ★★★★★

Download from Www.Somanuals.com. All Manuals Search And Download.

Sonic Blue CD Player MVP841 User Manual
Sony Car Stereo System Model CDX 3800 User Manual
Sony Network Card TDM BT1 User Manual
SOYO Computer Hardware SY 6ZB User Manual
State Industries Water Heater 317998 002 User Manual
Sterling Plumbing Indoor Furnishings 11605 NA User Manual
Summit Refrigerator FF7LBISSTB User Manual
Sunrise Medical Mobility Aid S 626 User Manual
SVAT Electronics Security Camera VU5 User Manual
Symantec Server Security Expressions Server User Manual