Sylvania TV VCR Combo 6309CE User Manual

OWNER’S

MANUAL

9-INCH COLOR TV/VCR

6309CE

This Owner’s Manual is made of

recycled paper.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®

is a U.S. registered mark.

If you need additional assistance for set-up or operating after

reading owner’s manual, please call TOLL FREE : 1-800-968-3429.

Or visit our WEB SITE at http://www.funai-corp.com

Please read before using this equipment

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/VCR to its normal operation.

14.Lightning-For added protection for this TV/VCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/VCR due to lightning and

power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR, ask the service technician to perform routine

safety checks to determine that the TV/VCR is in proper

operating condition.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/VCR.

22.Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

- 3 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

ature differences are extreme.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore when the condensation occurs

inside the unit, turn the POWER button on and allow

at least 2 hours for the unit to dry out.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

C TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .5

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C OPERATING CONTROLS AND FUNCTIONS 7

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .18

NORMAL RECORDING . . . . . . . . . . . . . . . . .19

SKIPPING UNWANTED SCENES DURING

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19

OTR (One Touch Recording) . . . . . . . . . . . . . .19

TIMER RECORDING . . . . . . . . . . . . . . . . . . .20

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .22

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .22

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .22

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .23

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . . .11

SELECTING THE LANGUAGE . . . . . . . . . . .11

CLOCK SET UP (AUTO / MANUAL) . . . . . .11

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13

CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . .14

DELETING (OR ADDING) CHANNEL . . . . .14

C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .23

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .24

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .24

REAL TIME TAPE COUNTER . . . . . . . . . . . .24

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .24

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .15

WATCHING A TV PROGRAM . . . . . . . . . . . .15

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .15

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .15

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .15

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .24

C TROUBLESHOOTING GUIDE . . . . . . . . . . .25

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .26

C CABLE CHANNEL DESIGNATIONS . . . . . .26

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .16

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .16

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .16

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .17

NOISE CANCEL (in the Still mode) . . . . . . . .18

VERTICAL HOLD CONTROL . . . . . . . . . . . .18

TRACKING ADJUSTMENT . . . . . . . . . . . . . .18

RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .18

INDICE

CONTROLES DE OPERACIÓN Y

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .27

MODO DE ENTRADA EXTERNA . . . . . . . . . . .30

SELECCION DE IDIOMA . . . . . . . . . . . . . . . . .30

AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . .31

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

CONEXIONES DE ANTENA/CABLE . . . . . . . .29

INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

- 5 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

Infrared remote control

Trilingual on screen menu display selectable in

English, Spanish or French

Still–“Freeze” the picture at any time, for close viewing

of a particular scene. Only tapes recorded in SLP mode

will show a fairly clear picture.

•

Digital Auto Tracking (DTR)–Automatically adjusts the

tracking for each tape you play.

Rental play mode–Improves playback picture quality

from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a tape

indefinitely without pressing the PLAY button.

Time search–Let you set the TV/VCR to advance the

tape by entering the desired playback time you want to

skip.

OTR (One Touch Recording)–Instant timed recording

from 30 to 480 minutes is possible at the push of the

REC/OTR button.

1 Year, 8 events (including Daily and Weekly Timer

Recording)–The built-in timer allows you to record up

to 8 programs at different times on different channels up

to 1 year in advance. The Daily timer allows recordings

to be made of daily broadcasts, and the Weekly timer

allows recording to be made once a week up to the end

of the tape.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the recording.

Wake up/Sleep timer–Allows you to have the TV/VCR

automatically turn on or off at a desired time.

Timer Program Extension–Allow you to shift the time

schedule for automatic timer recording.

Two- way power–Allows you to power the TV/VCR

with standard household AC or your vehicle’s battery,

using the supplied car-battery cord.

•

Real time counter–This shows the elapsed recording or

playback time in hours, minutes, and seconds. The “–”

indication will appear when the tape is rewound further

than the tape counter position “0:00:00”.

181 channel capability PLL frequency synthesizer

tuner with direct station call–(A converter may be nec-

essary to view scrambled cable channels.)

•

Auto Clock Setting–Allows you to set the clock function

from a PBS broadcast station.

•

Game mode–Automatically sets external input mode and

allows TV/VCR display to be suitable for use with TV

games.

Auto power on and off system–Automatically turns on

the TV/VCR when you insert the cassette, turns off after

auto-rewind, and ejects when the beginning of the tape is

reached.

•

Auto rewind when the end of a tape is reached–This

function doesn’t occur when using timer recording.

•

2 Step picture search operation–You can view a video

program at a high speed or super high speed in either a

forward or reverse direction in LP and SLP mode. For

SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video heads as

you insert or remove a cassette.

Zero Return–The tape returns to counter of 0:00:00 by

rewinding or fast forwarding.

•

SUPPLIED ACCESSORIES

Dipole Antenna

Matching Adapter

(300ohm-75ohm)

Remote Control Unit

Car Battery Cord

(1813641 or 1780258 or

UCPGANTPK004)

2 AA Batteries

(0EMN00723 or

0EMN01183)

PART NO.

(NE107UD or NE150UD)

WPZ0202GA004

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

- 6 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- TV/VCR FRONT PANEL -

POWER

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

VOLUME

CHANNEL

VIDEO AUDIO

EARPHONE

REC

1 2 3 4

5 6 7 8 9 10 11

12 13 14

5 POWER button– Press to turn TV/VCR on and off.

Press to activate timer recording.

6 STOP button– Press to stop the tape motion.

EJECT button– Press in the Stop mode to remove

tape from TV/VCR.

- REMOTE CONTROL -

WAKE-UP

/SLEEP

POWER

EJECT

L button–

CHANNEL

RETURN

Press to select setting modes from the on screen

menu.

•

Press to enter digits when setting program.

•

CHANNEL

VOLUME

(for example: setting clock or timer program)

7 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

+100

DISPLAY

MUTE

s button–

Press to select a mode from a particular menu.

•

PLAY

(for example: LANGUAGE or USER’S SET UP)

8 PLAY button– Press to begin playback.

K button–

REW

F.FWD

STOP

SPEED PAUSE/STILL

RECORD

Press to select setting modes from the on screen

menu.

Press to enter digits when setting program.

(for example: setting clock or timer program)

9 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

•

T-PROG.

CLEAR

GAME

TIME SEARCH

COUNTER

RESET

•

1 VIDEO input jack– Connect to the video output

jack of your video camera or another VCR.

2 AUDIO input jack– Connect to the audio output

jack of your audio equipment, video camera or

another VCR.

B button–

When setting program (for example: setting

•

clock or timer program), press to determine your

selection and proceed to the next step you want to

input.

3 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer

Recording.

4 Remote Sensor Window– Receives the infrared

signals from the remote control.

Press to determine setting modes from on screen

menu.

Press to select a mode from a particular menu.

(for example: LANGUAGE or USER’S SET UP)

•

- 7 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

- REAR VIEW -

10 REC(RECORD) button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

11 VOLUME X / Y buttons– Adjust the volume

level.

12 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording.

You may display the main menu on the TV screen

by pressing repeatedly this button on the

TV/VCR.

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 22.)

COUNTER RESET button– Press to reset counter

to 0:00:00.

20 GAME button– Sets the game mode and external

input mode at the same time. (See page 15.)

21 TIME SEARCH button– Press to activate Time

Search mode.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback

mode. (See page 18.)

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

23 MUTE button– Mutes the sound. Press it again to

resume sound.

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

25 WAKE-UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See pages 22 and 23.)

26 ANT. terminal– Connect to an antenna or cable

system.

14 Cassette compartment

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

+100 button– When selecting cable channels

which are higher than 99, press this button first,

then press the last two digits. (To select channel

125, first press the “+100” button then press “2”

and “5”.)

16 MENU button– Press to display the main menu on 27 DC 13.2V jack– Connect to the Car Battery Cord.

the TV screen.

28 Power cord– Connect to a standard AC outlet

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 24.)

(120V/60Hz).

- 8 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION FOR USE

From Cable System or

Satellite Dish

Satellite Box or

Dipole Antenna

(Supplied)

VHF/UHF Antenna

(Not supplied)

OUT

Cable Box

Flat twin-lead cable

(Not supplied)

VHF Antenna

(Not supplied)

Matching Adapter

(Supplied)

UHF Antenna

(Not supplied)

From

Cable System

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not

supplied)

Flat twin-lead cable

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

ANTENNA/CABLE

CONNECTIONS

DIPOLE ANTENNA HOOK UP

1. Push the stem of the Dipole Antenna (supplied)

into the hole for antenna at the back of TV/VCR.

2. Connect the flat twin-lead cable from the Dipole

Antenna to the 300/75 ohm Matching Adapter

(supplied).

3. Plug the Matching Adapter to ANT terminal of

TV/VCR as shown in drawing.

For the best reception, extend the Dipole Antenna and

adjust its length and position. (Avoid handling the top

section when making adjustments.)

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in drawing.

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

NOTE: If it is difficult to get good reception with the

indoor antenna, the use of an outdoor antenna is rec-

ommended. Before an outdoor antenna is connected

to the set, the indoor antenna should be disconnected.

VHF/UHF COMBINED ANTENNA

A VHF UHF 75 ohm combination antenna can be

connected to ANT terminal.

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

1. Set the TV/VCR channel selector to the output channel

of the Cable Converter Box or Satellite Box. (Ex. CH3)

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor

antenna.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

- 9 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

To the vehicle's

cigarette-lighter socket

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

VHF/UHF Combination

Mobile Antenna

(Not supplied)

Car battery cord

(Supplied)

3)Replace the cover.

DC13.2V

ANT.

NOTES:

Be sure your vehicle has a 13.2-volt (12-volt), neg-

ative-ground electrical system.

•

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO IN/ VIDEO IN jacks of

your TV/VCR. Then press the CHANNEL K or

button until “AUX” appears on the screen.

Be sure you use only the supplied car battery cord.

Using another cord could damage the TV/VCR.

Be sure the socket is free of ashes and other debris.

Be sure to push the car battery cord’s plug com-

pletely into the cigarette-lighter socket.

Always unplug the car battery from the cigarette-

lighter socket before you unplug it from the

TV/VCR.

•

AUX

You must disconnect the car battery cord from the

TV/VCR before you can use the AC power.

Be sure to replace the fuse with only the same type,

5A, 250V.

•

Be sure the AC cord is wound as shown below.

MOBILE CONNECTION

WARNING:The driver should never watch

the TV/VCR while operating a motor vehicle.

CAUTION: If you use the TV/VCR with the

vehicle’s engine off, recharge the vehicle’s

battery after about every 4 hours of use to

prevent it from running down. After you fin-

ish using the TV/VCR be sure you unplug the

car-battery cord from the cigarette-lighter

socket.

1) The supplied indoor antenna is adequate when

your vehicle is stationary. For best reception on

the road, use a high-quality VHF/UHF mobile TV

antenna.

2) Attach the car battery cord to the DC13.2V (12V)

connector on the back of the TV/VCR. Then, con-

nect the other end to your vehicle’s cigarette-

lighter socket.

- 10 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

SET UP FOR USE

CLOCK SET UP

SELECTING THE LANGUAGE

(AUTO / MANUAL)

1 Plug in the TV/VCR power cord

Plug the TV/VCR power cord into a

standard AC outlet.

The TV/VCR clock must be set correctly before VCR

timer recording is possible. It is suggested that the

clock be set manually when first setting up the

TV/VCR. Then, set to [ON] the auto clock setting

which will periodically correct the setting if necessary.

NOTE: If you cannot receive a station with time sig-

nals, auto clock setting cannot be performed. Use

manual setting only.

NOTE:

If some digits appear in the corner of

the screen, press the POWER button

without unplugging the power cord.

•

Make sure ...

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

the screen menu and not the audio source.

MANUAL CLOCK SETTING

•

Make sure ...

The TV/VCR is turned on.

•

In the example below, the clock is to be set to:

DATE

May 6th, 2004

– M E N U –

2 Select “LANGUAGE”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

SETTING TIME 5:40PM

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “LANGUAGE”.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

3 Select “ENGLISH”, “ESPAÑOL” or

“FRANÇAIS”

Select “ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the F.FWD/B or

REW/s button.

Press the PLAY/K or STOP/L

button to point to “SETTING

CLOCK”.

Then, press the F.FWD/B button.

2 Select “MANUAL CLOCK SET”

Press the PLAY/K or STOP/L

button to point to “MANUAL

CLOCK SET”.

– SETTING CLOCK –

4 Exit the Language mode

Press the MENU button on the remote control to

return to TV mode.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

Then, press the F.FWD/B button.

NOTE: If for some reason the menu is in Spanish or

French, press the MENU button on the remote con-

trol, press the PLAY/K button to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then

press the F.FWD/B button, then press the MENU

button on the remote control.

3 Select the month

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the PLAY/K or STOP/L but-

ton until your desired month

appears. (Example: May → 05)

Then, press the F.FWD/B button.

0 5

– – – – – – – – –

HOUR

– –

MINUTE

– – – –

4 Select the day

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 6th → 06)

0 5

0 6 – – – – – – –

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

- 11 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

system connection using the ANT. terminal on the

rear of the TV/VCR.

NOTE:

If a cable converter box is being used, make sure it

is powered on.

You must use the TV/VCR remote control to per-

form the clock setting procedure.

If the TV/VCR is connected directly to a cable

converter box or satellite box, the local PBS station

must be selected on the cable box itself, and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically.

5 Select the year

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2004)

•

0 5

0 6 THU 2 0 0 4

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

6 Select the hour

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 THU 2 0 0 4

HOUR

0 5

MINUTE

– – PM

Then, press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: 40)

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

0 5

0 6 THU 2 0 0 4

– M E N U –

HOUR

0 5

MINUTE

4 0 PM

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

8 Start the clock

Press the MENU button on the

remote control.

Although seconds are not dis-

played, they begin counting from

00 when you press the MENU but-

ton on the remote control. Use this

5:40 PM

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B button until

“AUTO CLOCK [ON]” appears.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

feature to synchronize the clock with the correct

time.

NOTE:

3 Begin “AUTO CLOCK CH SEARCH”

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

Press the STOP/L button to select

– SETTING CLOCK –

“AUTO CLOCK CH SEARCH”.

Press the F.FWD/B button.

The TV/VCR is now searching

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

•

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps [1] and [2].

2)Select where you want to change using the

F.FWD/B or REW/s button.

3)Enter correct numbers using the PLAY/K or

STOP/L button.

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

seconds per channel.

– AUTO CLOCK CH SEARCH –

“_ _” appears at the lower left of

•

the screen when the search has

ended.

_ _

Auto Clock station- write down

•

4)Press the MENU button on the remote control to

start the clock.

the number(s) that appear on the screen. These are

the auto clock station(s) in your area. See step [4]

on the next page.

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 11.

Press the MENU button to exit the screen.

NOTE: During Auto Clock CH Search, the picture

may be distorted. This is normal.

PLEASE NOTE:

•

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the F.FWD/B or REW/s button to turn [OFF]

this function. Then you can manually adjust the

clock.

AUTOMATIC CLOCK SETTING

Make sure ...

The TV/VCR is turned on.

Confirm the TV/VCR is receiving a RF (Radio

Frequency) signal from either an antenna or cable

•

- 12 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

First Sunday of April : At 2 AM the clock imme-

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the MENU button on the

– M E N U –

remote control.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

Press the STOP/L button to select

“AUTO CLOCK CH”.

Press the F.FWD/B or REW/s

buttons until you locate Auto Clock

Set station number. Follow step [3]

on page 12.

TIME SEARCH

•

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[

45]

•

[OFF]

Make sure ...

Press the POWER button to turn on the TV/VCR.

•

Press the MENU button to exit the screen.

1 Select “SETTING CLOCK”

Press the MENU button on the

5 Turn off the TV/VCR

Once the TV/VCR is turned off , it will periodically

check and set the correct date and time.

– M E N U –

remote control.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

TIME SEARCH

Then, press the F.FWD/B button.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the PLAY/K or STOP/L but-

– SETTING CLOCK –

ton to point to “D.S.T.”.

Then, press the F.FWD/B or

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[ON]

REW/s button until [ON] appears.

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

F.FWD/B or REW/s button. Then, press the MENU

button to return to TV mode.

- 13 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

DELETING (OR ADDING)

CHANNEL

CHANNEL SET UP

You can program the tuner to scan all the channels

you receive in your area.

NOTE: Channel memory programming is NOT

needed when connected to a cable box or satellite

box. Just select the TV/VCR channel selector to the

output channel of the cable box or satellite box (Ex

CH3). Then select the channel to be viewed on the

Cable Box or Satellite Box.

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

– M E N U –

1 Select “CHANNEL SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

remote control. Then press the

PLAY/K or STOP/L button to

point to “CHANNEL SET UP”.

Then, press the F.FWD/B button.

Make sure ...

Press the POWER button to turn on the TV/VCR.

TIME SEARCH

•

1 Select “CHANNEL SET UP”

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

– CHANNEL SET UP –

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

TIME SEARCH

Press the F.FWD/B button.

Then, press the F.FWD/B button.

3 Enter the desired channel number

Press the PLAY/K or STOP/L but-

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it.) (Example:

CH8)

2 Begin auto ch programming

Press the PLAY/K or STOP/L but-

ton to point to “AUTO CH PRO-

GRAMMING”.

Then, press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

ADD / DELETE

4 Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

3 After scanning

The tuner stops on the lowest memorized channel.

•

When AUTO CH PROGRAMMING is activated

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

•

where there is no TV signal input, “NO TV SIG-

NALS” will appear on the display after the com-

pletion of the channel scanning.

again, the channel is memorized again.

The TV/VCR may recognize TV channels to be

•

Added channel: Light blue.

Deleted channel: Light red.

CATV channels by the receiving conditions. In this

case, try auto ch programming again in the fine

receiving conditions.

5 Exit the channel setup mode

Press the MENU button on the remote control to

returns to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

- 14 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

3 Adjust sound

Press the VOLUME X or Y button

to adjust the volume.

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

remote control.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Press the PLAY/K or STOP/L but-

ton to point to ”PICTURE CON-

TROL”.

VOLUME 20

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

GAME MODE

2 Select item you want to adjust

This function enables you to decrease the TV screen

contrast and making it suitable for use with a TV

GAME.

Press the PLAY/K or STOP/L but-

ton until desired control is dis-

played.

NOTE: This function CANNOT be set during recording.

BRIGHT

–

P +

CONTRAST

COLOR

TINT

GAME

Press the GAME button on the

remote control. “GAME” appears

on the screen.

SHARPNESS

When you press the GAME button;

3 Adjust the picture control

The TV/VCR comes on automatically if it is off.

The TV/VCR will be in external input mode auto-

matically.

•

Press the F.FWD/B or REW/s button to adjust to

your desired level.

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

ton on the remote control.

BRIGHT

CONTRAST

DEGAUSSING

Magnetism from nearby appliances might affect the

color of the TV picture.

COLOR

TINT

to pale

to brilliant

to purple

to green

to clear

SHARPNESS to soft

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect

power cord from AC outlet then reconnect it after 30

minutes.

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 15 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

This TV/VCR will operate with any cassette that has the

mark. For best results, we

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

AUTO REPEAT PLAYBACK

The TV/VCR has the auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

cassette until it is drawn into the TV/VCR. The

TV/VCR will automatically turn on.

Window

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

WRONG

CORRECT

PRECAUTIONS

Avoid moisture. Moisture condensation may occur

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

•

1 Select “USER’S SET UP”

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

USER’S SET UP

•

2 Select “ALL” or “BLANK”

Press the PLAY/K or STOP/L but-

ton to point to “REPEAT PLAY”.

Press the F.FWD/B or REW/s

button repeatedly until your desired

–

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

NORMAL PLAYBACK

Make sure ...

selection [ALL] or [BLANK] appears.

TV/VCR power must be turned on.

•

3 Exit the Repeat Play setting

Press the MENU button on the remote control to

return to the TV mode.

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

2 To begin playback

4 Start playback

PLAY

Press the PLAY button.

Press the PLAY button to start the Repeat Play.

”REPEAT PLAY B” appears.

•

Note: If any menu is activated on

the screen, the PLAY button does

not function. Press the MENU but-

ton to clear the menu. then, press

the PLAY button.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

3 To stop playback

Press the STOP button when play-

back is completed.

STOP

TO CANCEL THE REPEAT PLAY MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

- 16 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

Time Search can be set up to a maximum of 9

•

hours 50 minutes (9:50) by 10 minutes at a time.

PICTURE SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

This function will not operate in recording mode.

•

In the example below: To watch a program after 2

hour 50 minutes from the present position, in either

direction.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback. (in the

SP / LP / SLP modes)

2)Press it again and the TV/VCR will now search in

super high speed. (in the LP / SLP modes only)

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

1 Insert a tape.

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button (with each push it

will increase by 10 minute).

3 Enter your desired time

Press the PLAY/K or STOP/L but-

TIME SEARCH

2 : 50

ton until your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

If you wish to cancel the Time Search at this point,

press the MENU button on the remote control.

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

4 Begin Time Search

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/VCR or the

remote control. This will delete the selected time.

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

STILL PICTURE

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines. Press

the PLAY button to return to playback.

NOTES:

4 To activate “ZERO RETURN” mode

Press the MENU button on the

– M E N U –

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “ZERO RETURN”.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Usually there will be video “noise” lines (black

and white streaks or dots) on the screen. This is

normal.

•

Then, press the F.FWD/B button.

The counter will appear on the TV

screen.

The tape will automatically stop when the counter

returns to 0:00:00.

If the tape was originally recorded in SP or LP

mode, the still picture will be black and white in

addition to the “noise” lines.

This is not a fault of the machine, but is a by-

product of the technology involved in producing

a TV/VCR with 2 video heads.

If it is left in the Still mode for more than five min-

utes, the TV/VCR will automatically switch to the

Stop mode.

TIME SEARCH

The Time Search function makes it possible to

quickly advance the tape to your desired position

simply by entering the exact amount of playback

time you want to skip.

•

- 17 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

NOISE CANCEL (in the Still mode)

RENTAL PLAYBACK

This feature allows you to reposition or reduce the

noise lines of a still picture. Press the PAUSE/STILL

button so that the noise lines change position on the

screen so you can see the picture in its entirety with-

out distracting noise lines.

NOTE: This feature can be activated ONLY when

viewing a tape recorded in the SLP mode. If the tape

was originally recorded in the SP or LP mode, the

still picture may revert to black and white in addition

to the “noise bars”. This is normal.

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

Press the MENU button on the

remote control.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

VERTICAL HOLD CONTROL

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

NOTE:

If there are video noise lines on the screen, reposition

or reduce them. Refer to “NOISE CANCEL”.

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

TRACKING ADJUSTMENT

4 Start playback

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR.

•

However when playing pre-recorded tapes or tapes

•

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

RECORDING

TWO DIFFERENT TAPE SPEEDS

ERASE PREVENTION

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

Tape Speed

Type of tape

SP mode

Recording/Playback Time

If you decide to record on

the tape again, cover the

hole with plastic tape.

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

Note: You can play back a tape recorded in LP mode

(Long Play).

Plastic Tape

- 18 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

Make sure ...

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTE: This unit will ONLY record and view the same channel.

NORMAL RECORDING

OTR (One Touch Recording)

You can ONLY watch the same TV program that is

being recorded.

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/VCR.

Make sure ...

1 Select the channel to be recorded

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab

Press the number buttons on the

•

CH 10

remote control or the CHANNEL

K or L button.

in place. (If necessary, rewind or fast forward the

Remember: If the TV/VCR is con-

nected to a cable box or satellite

box, the TV/VCR must be on CH3

or CH4, then the channel to be recorded must be

selected on the cable box or satellite box.

tape to the point at which you want to begin

recording.)

NOTES:

This function CANNOT be done from the remote

control.

•

Recording starts immediately when the REC/OTR

button is pressed.

When the REC/OTR button is pressed 18 times, the

TV/VCR returns to the Normal Recording mode.

•

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

•

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

•

To show the remaining time, press the DISPLAY

•

button on the remote control so that “OTR”

appears on the TV screen. (It will show up momen-

tarily then disappear.)

REC

3 Begin recording

Press the RECORD button.

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum record-

ing time, assuming the tape is started at the begin-

ning, is 8 hours using T-160 (or 6 hours using T-120).

•

4 Stop recording

Press the STOP button when recording is completed.

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, ejects the tape and turns itself off.

•

If you press the power button during OTR, the

TV/VCR continues recording until the selected

length is reached.

•

SKIPPING UNWANTED

SCENES DURING RECORDING

Press the PAUSE/STILL button to

PAUSE

temporarily stop recording.

Press the PAUSE/STILL or

RECORD button to resume record-

ing.

NOTES:

1 Select the channel to be recorded

Press the number buttons on the remote control or the

CHANNEL K or L button.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape dam-

age.

•

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

- 19 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

Avoid over lap of programs ...

There is a chance that a program will not be record-

ed. when programs overlap;

3 Begin OTR

OTR(2 : 30)

Press the REC/OTR button on the

TV/VCR as many times as needed.

The recording length will be deter-

mined by the number of times you

press the REC/OTR button. Each

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

The illustration below demonstrates the sequence

of recordings.

additional push will increase the recording time by

30 minutes. It is set up to 8 hours.

•

Recording Sequence

Push(es) Display

1 push

Recording length

(normal recording)

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

17 pushes

8:00

480 minutes

1 Select “TIMER PROGRAMMING”

Press the MENU button on the remote control.

TIMER RECORDING

Confirm “TIMER PROGRAM-

MING” is pointed by pressing the

PLAY/K button.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

In the example below, the timer is being set to record:

July 5th, 2004

SETTING TIME: from 7:30PM to 8:50PM

And press the F.FWD/B button.

If you have not yet set the clock,

•

“MANUAL CLOCK SET” appears. If so, follow

steps [3] to [8] on pages 11 and 12. Then set the

timer recording.

DATE:

CHANNEL:

TAPE SPEED:

CH61

2 Select your desired program position (1~8)

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L but-

Make sure ...

CH DATE

BEGIN END

ton to select the desired program

position.

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

If a cable box or satellite box is connected with the

TV/VCR you will be limited to record only one

channel. And the channel selector on the TV/VCR

must be selected to the output channel of the boxes

CH 3 or CH 4 and then the actual channel to be

recorded must be selected on the boxes.

Clock must be set to the correct time and date

before setting the timer.

TV/VCR power must be turn on to program it.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

3 Set the channel number

Press the PLAY/K or STOP/L but-

ton until the desired channel num-

ber appears.

(Example: CH61)

Then, press the F.FWD/B button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

•

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

•

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

The channel you want to record is properly set in

advance.

•

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Press the PLAY/K (up) button

until the desired date appears.

(Example: “7/05” for July 5th).

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 7/05 MON -:- -

- - -/- - - - - -:- -

-:- - - -

- 20 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

For every day recording : To record a TV program at

the same time on the same channel every day.

(Example: Monday through Sunday)

10 Finish setting the program

Press the F.FWD/B or REW/s button. The program

is now completed.

Press the STOP/L (down) button

– TIMER PROGRAMMING –

CH DATE

BEGIN END

until “EVRY DAY” appears.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control to

•

return to original mode.

For weekly recording : To record a TV program at

the same time on the same channel every week.

(Example: every Monday)

11 Set the timer

Press the POWER button to set automatic timer

recording. The TIMER REC indicator lights up.

– TIMER PROGRAMMING –

Press the STOP/L (down) button

You must turn off the TV/VCR to activate automat-

ic timer recording.

CH DATE

BEGIN END

•

until “EVRY” and your desired

day of the week appear together.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

– TIMER PROGRAMMING –

CH DATE BEGIN END

5 Set beginning hour

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “ 7, PM” for 7:30PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/05 MON 7:12^P

- - -/- - - - - -:- -

2)Repeat step [1] on page 20.

3)Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the

– TIMER PROGRAMMING –

CH DATE BEGIN END

6 Set beginning minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: “30” for

7:30PM)

- - -/- - - - - -:- -

-:- - - -

61 7/05 MON 7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

5)Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

– TIMER PROGRAMMING –

CH DATE BEGIN END

7 Set end hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:30 - -

-:- - - -

61 7/05 MON 7:30^P

- - -/- - - - - -:- -

8 Set end minute

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: “50” for

8:50PM)

TO CORRECT A PROGRAM

- - -/- - - - - -:- -

-:- - - -

8:50 - -

-:- - - -

61 7/05 MON 7:30^P

- - -/- - - - - -:- -

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

bers using the PLAY/K or STOP/L button.

Then, press the F.FWD/B button.

After setting a program;

1)Press the POWER button.

•

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

– TIMER PROGRAMMING –

CH DATE BEGIN END

2)Repeat steps [1] - [2] on page 20.

3)Press the F.FWD/B button (or press the REW/s

button to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the PLAY/K or STOP/L but-

ton.

- - -/- - - - - -:- -

-:- - - -

8:30 SP

-:- - - -

61 7/05 MON 7:30^P

- - -/- - - - - -:- -

4)Press the POWER button to set automatic timer

recording.

- 21 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears. Then,

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

After setting a program;

1)Press the POWER button.

•

2)Repeat steps [1] ~ [2] on page 20 and select a

program you want to cancel.

3)Press the T-PROG. CLEAR button.

4)Press the MENU button on the remote control to

return to TV mode.

press the MENU button on the remote control to

return to TV mode.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/VCR will rewind to the beginning of the recorded

While recording is in progress;

1)Press POWER button.

•

program(s).

NOTE:

2)Press the STOP/EJECT button on the TV/VCR.

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

If you press the POWER button while tape is

•

rewinding, the Auto Return will stop.

2)Press the MENU button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

5)Press the MENU button on the remote control to

return to TV mode.

4 Watch the recorded program

Press the PLAY button.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Then, press the MENU

button on the remote control to return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

HINTS FOR AUTOMATIC

TIMER RECORDING

Make sure the channel you want to record is prop-

erly set in advance.

•

It is not necessary to press the RECORD button for

timer recording.

•

WAKE UP TIMER

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

•

NOTES:

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, and the tape will be ejected.

•

Use the remote control for this procedure.

Clock must be set to the correct time before setting

the timer.

•

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

1 Select “WAKE UP TIMER”

Press the WAKE-UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

WAKE UP B ON/OFF [ON]

TIMER

TV/TAPE [TV]

TIME

[12:00AM]

button until [ON] appears.

1 Select “USER’S SET UP”

2 Select “TV” or “TAPE”

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

Press the PLAY/K or STOP/L but-

ton until to point to “TV/TAPE”.

Press the F.FWD/B or REW/s

button, and select [TV] or [TAPE].

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

WAKE UP

TIMER

ON/OFF [ON]

B TV/TAPE [TV]

TIME

[12:00AM]

- 22 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

SLEEP TIMER

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

3 Set wake up time

Press the PLAY/K or STOP/L but-

ton until to point to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

NOTE:

WAKE UP

TIMER

ON/OFF [ON]

TV/TAPE [TV]

B TIME

[12:00AM]

This function does not operate during Recording

•

mode.

Each additional push will increase (or decrease) the

time by 10 minutes.

1 Select “SLEEP TIMER”

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

2 Set sleep time

TO CANCEL THE WAKE UP TIMER

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

Press the WAKE-UP/SLEEP button on the remote

control once, and confirm “ON/OFF” is pointed.

Press the F.FWD/B or REW/s button until [OFF]

appears.

SLEEP TIMER [2:00]

your desired sleep time appears.

Each additional push will increase

the time by 30 minutes up to 120 minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE SLEEP TIMER

Press the WAKE-UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer, press the

WAKE-UP/SLEEP button twice, then press the

MENU button on the remote control to exit the sleep

timer setting.

COPYING A VIDEO TAPE

You can make copies of video tapes made by friends

or relatives for your enjoyment.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record over, into the TV/VCR’s cassette compart-

ment.

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

4)Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

NOTE: “AUX” is found below the lowest memo-

rized channel. (Example: CH2)

POWER

VIDEO AUDIO

[The TV/VCR]

REC

5)Press the RECORD button on the TV/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during dubbing, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

[Ex: Source (playing)

VCR or camcorder]

7)To stop copying, press STOP/EJECT button on the

TV/VCR, then stop the tape on the source VCR or

camcoder.

AUDIO

Audio/Video

adapter cable

(not supplied)

OUT

VIDEO

- 23 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

5:40PM

CH2

Press

once

Press

once

COUNT 0:12:34

Press once

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time

will not change on a blank tape or blank portions on

the tape.)The “–” indication will appear when the

tape has rewound further than “0:00:00” on the tape

counter.

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

CABINET CLEANING

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-968-3429, to

locate an Authorized Service Center.

NOTES:

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

Should your TV/VCR become inoperative, do not

•

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

Playback picture may become blurred of interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your TV/VCR may need

to be cleaned.

- 24 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

No power.

Make sure the AC cord is connected to an AC outlet.

Make sure the car battery cord is connected to vehicle’s cigarette

lighter socket and to DC 13.2V (12V) jack on back of the TV/VCR.

Check the fuse (5A, 250V) in car battery cord.

•

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the TV/VCR program it's tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

Timer recording is not possible.

Cannot go into Record mode.

Playback picture is partially noisy.

Adjust tracking control for a better picture using the CHANNEL

or L button on the TV/VCR.

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 24.

No picture but the audio is OK in

playback.

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

Cannot set the auto clock to ON.

Different color makes on screen.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

•

Make sure the AC cord is connected to an AC outlet.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the TV/VCR away from the appli-

ances, the TV/VCR can repair itself automatically. If you want to

repair immediately, unplug the TV/VCR power cord, then plug it in

again 30 minutes or so later.

- 25 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

9 inch in-line gun, 90˚

deflection tube

NTSC-M

Rotary two-head

1/2 inch

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

OTHER SPECIFICATIONS

Power requirement : AC 120V/60Hz

DC 13.2V

Power consumption : AC 55W / DC 60W

Dimensions :

#2~#6

#7~#13

#14~#69

H:13” (330mm)

W:12-1/8” (308mm)

D:12-15/16” (329mm)

18.5 lbs (8.4kg)

CATV

VHF :

Weight :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Designs and specifications are subject to change

without notice.

If there is a discrepancy between languages, the

default language will be English.

•

Antenna input :

VHF/UHF 75 ohms

unbalanced

Video input :

Audio input :

Earphone :

RCA connector [ 1

1/8” monaural (3.5 mm)

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 26 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

- PANEL DELANTERO -

POWER

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

VOLUME

CHANNEL

VIDEO AUDIO

EARPHONE

REC

1 2 3 4

- CONTROL REMOTO -

6 7 8 9 10 11

12 13 14

6 Botón de parada (STOP)– Púlselo para detener

la cinta.

Botón de expulsión (EJECT)–Púlselo en el

modo de parada para expulsar la cinta del televi-

sor/videograbadora.

WAKE-UP

/SLEEP

POWER

EJECT

CHANNEL

RETURN

Botón L–

Púlselo para seleccionar los modos de ajuste desde

•

el menúde la pantalla.

CHANNEL

VOLUME

Púlselo para introducir dígitos cuando establezca

•

un programa.

(Por ejemplo: Para ajustar el reloj o establecer un

programa de temporizador)

7 Botón de rebobinado (REW)– Púlselo para

rebobinar la cinta, o para ver la imagen en retroceso

rápido durante el modo de reproducción. (Búsqueda

con rebobinado)

+100

DISPLAY

MUTE

PLAY

REW

F.FWD

STOP

Botón s–

SPEED PAUSE/STILL

RECORD

Púlselo para seleccionar un modo desde un menú-

•

particular.

T-PROG.

CLEAR

GAME

TIME SEARCH

(Por ejemplo: IDIOMA o ADJUST DE USER)

8 Botón de reproducción (PLAY)– Púlselo para

iniciar la reproducción.

COUNTER

RESET

Botón K–

Púlselo para seleccionar los modos de ajuste desde

•

el menú de la pantalla.

1 Toma de entrada de vídeo (VIDEO)–

Conéctela a la toma de salida de vídeo de su

videocámara u otra videograbadora.

Púlselo para introducir dígitos cuando establezca

•

un programa.

(Por ejemplo: Para ajustar el reloj o establecer un

programa de temporizador)

9 Botón de avance rápido (F.FWD)– Púlselo para

avanzar rápidamente la cinta, o para ver la imagen

en avance rápido durante el modo de reproducción.

(Búsqueda con avance rápido)

2 Toma de entrada de audio (AUDIO)–

Conéctela a la toma de salida de audio de su equipo

de audio, videocámara u otra videograbadora.

3 Indicador de grabación (RECORD)– Parpadea

durante la grabación.

Se enciende en el modo de espera de la grabación

Botón B–

con temporizador.

Cuando establezca un programa (por ejemplo: para

4 Ventanilla sensora del mando a distancia–

Recibe las señales infrarrojas procedentes del

mando a distancia.

5 Botón de la alimentación (POWER)– Púlselo

para encender y apagar el televisor/videograbadora.

Púlselo para activar la grabación con temporizador.

•

ajustar el reloj o para establecer un programa de

temporizador), púlselo para determinar su elección y

vaya al paso siguiente que quiera introducir.

Púlselo para determinar los modos de ajuste desde

•

el menú de la pantalla.

- 27 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

- PANEL TRASERO -

Púlselo para seleccionar un modo desde un menú

•

18 Botón de velocidad de cinta (SPEED)–

particular.

Púlselo para elegir la velocidad de grabación desea-

da: SP/SLP.

(Por ejemplo: IDIOMA o ADJUST DE USER)

10 Botón de grabación (REC)– Púlselo para ini-

ciar la grabación manual.

19 Botón T-PROG. CLEAR– Púlselo para cancelar

un programa de temporizador.

Botón de grabación de un toque (OTR)–

Activa la grabación de un toque. (Sólo en el televi-

sor/videograbadora)

Botón de reposición del contador

(COUNTER RESET)– Púlselo para reponer el

contador a 0:00:00.

11 Botones de volumen (VOLUME X / Y)–

20 Botón de juego (GAME)– Establece el modo

del juego y el modo de entrada externa al mismo

tiempo.

Ajustan el nivel del volumen.

12 Botones de canales (CHANNEL K/ L)–

Púlselos para seleccionar los canales deseados para

ver o grabar.

21 Botón de búsqueda con tiempo (TIME

SEARCH)– Púlselo para activar el modo de

búsqueda con tiempo.

Se puede mostrar el menú principal en la pantalla del

televisor pulsando repetidamente este botón del tele-

visor/videograbadora.

22 Botón de pausa/imagen fija

(PAUSE/STILL)– Púlselo para detener temporal-

mente la cinta durante la grabación o para ver una

imagen fija durante la reproducción.

Función de seguimiento– Pulse los botones

para minimizar el ruido de vídeo (líneas o puntos

en la pantalla) durante la reproducción.

13 Toma de auriculares (EARPHONE)– Para

conectar los auriculares (no suministrados) y

escuchar en privado. La toma es mono y tiene un

tamaño de 1/8”(3.5 mm).

14 Compartimiento del videocasete

15 Botones numerados– Púlselos para seleccionar

los canales deseados para ver o grabar. Para selec-

cionar canales del 1 al 9, pulse primero el botón 0 y

luego el botón 1 a 9.

Botón +100– Cuando seleccione canales de tele-

visión por cable cuyo número sea superior al 99,

pulse primero este botón, y luego pulse los dos últi-

mos dígitos. (Para seleccionar el canal 125, pulse

primero el botón “+100” y luego el “2” y el “5”.)

16 Botón de menú (MENU)– Púlselo para visu-

alizar el menú principal en la pantalla del televisor.

17 Botón del visualizador (DISPLAY)– Visualiza

el contador o el número del canal actual y la hora

actual en la pantalla del televisor.

23 Botón de silenciamiento (MUTE)– Silencia el

sonido. Púlselo de nuevo para recuperar el sonido.

24 Botón de retorno de canal (CHANNEL

RETURN)– Púlselo para volver al canal anterior.

Por ejemplo, pulsando una vez este botón, la visu-

alización del canal cambiará de 3 (canal actual) a

10 (canal anterior), y al pulsarlo por segunda vez,

el canal cambiará del 10 al 3.

25 Botón del temporizador despertador/para

dormir (WAKE-UP/SLEEP)– Ajusta el tempo-

rizador para despertarse/dormir.

26 Terminal de antena (ANT.)– Para conectar una

antena o sistema de televisión por cable.

27 DC 13.2V– Conecta el cordón para la batería del

automóvil.

28 Cordón de alimentación– Conéctelo a la toma

de CA estándar (120V/60Hz).

- 28 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIONES DE ANTENA/CABLE

Desde el cable coaxial

o caja de emisiones vía

satélite de 75 ohm del

sistema de Cable

Antena combinada de

VHF/UHF

(no incluído)

Antena Dipolar

(incluído)

OUT

Caja de CATV

o caja de emi-

siones vía satélite

(no incluído)

Antena VHF

(no incluído)

Adaptador de

acoplo (incluído)

Desde el

sistema de Cable

Antena UHF

(no incluído)

Combinador de

VHF/UHF

(no incluído)

ANT.

Cable coaxial

de 75 ohm (no

incluído)

Cable bifilar plano

realizar la grabación automática con temporizador.

NOTA: Con esta unidad SÓLO se podrá grabar y ver

un mismo canal al mismo tiempo.

CABLE CON CONVERTIDOR/DESCODI-

FICADOR O CONVERTIDOR DE EMI-

SIONES VÍA SATÉLITE

CONEXION DE LA ANTENA BIPOLAR

1.Introduzca la varilla de la antena bipolar (incluído)

en el orificio destinado para la antena, en la parte

trasera de la TV/VCR.

2.Conecte el cable bifilar plano de la antena bipolar

al adaptador de acoplo (incluído) de 300/75 ohm.

3.Enchufe el adaptador de acoplo al terminal ANT de

la TV/VCR, como lo muestra el dibujo.

Para obtener una mejor recepción, extienda la antena

de varilla y regule su longitud y posición. (Evite

tocar su parte superior mientras hace los ajustes.)

NOTAS: Si es difícil obtener una buena recepción

con la antena de interiores, se recomienda usar una

antena de exteriores. Antes de instalar una antena de

exteriores al aparato, se debe desconectar la antena

de interiores.

Si su servicio de televisión por cable le suministra un

convertidor, o si usted utiliza un sistema de emisiones

vía satélite, usted podrá utilizar las conexiones básicas.

Utilizando estas conexiones, usted también podrá

grabar canales codificados. Sin embargo, la selección

de los canales deberá hacerse con el convertidor de

televisión por cable con el convertidor de emisiones

vía satélite. Esto significa que los canales no podrán

ser cambiados con el mando a distancia del televi-

sor/videograbadora. La grabación inatendida se limita

a un canal cada vez.

ANTENA COMBINADA DE VHF/UHF

PARA GRABAR UN CANAL

CODIFICADO/DESCODIFICADO

1.Ajuste el selector de canales del

Una antena de combinación de 75 ohm para

VHF/UHF puede ser conectada al terminal ANT.

televisor/videograbadora al canal de salida del con-

vertidor de televisión por cable o del convertidor

de emisiones vía satélite. (Ej.: CA3)

2.Seleccione el canal que desee grabar de su conver-

tidor de televisión por cable o del convertidor de

emisiones vía satélite.

ANTENAS SEPARADAS DE VHF/UHF

En algunos lugares será necesario utilizar una antena

exterior.

CABLE SIN CONVERTIDOR/DESCODIFI-

CADOR

Aviso a los instaladores de sistemas CATV:

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su

televisor/videograbadora sin convertidor.Utilizando

esta conexión usted podrá:

1)Utilizar el mando a distancia del

televisor/videograbadora para seleccionar canales.

2)Programar uno o más canales sin codificar para

Este aviso se incluye para que los instaladores de sis-

temas CATV tenga en cuenta el Artículo 820-40 del

NEC, que proporciona consejos para hacer una conexión

apropiada a tierra y, en particular, especifica que el cable

de tierra deberá conectarse a un sistema de puesta a tier-

ra del edificio tan cerca del punto de entrada del cable

como sea posible.

- 29 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXION MOVIL

Al zócalo del encendedor

de cigarrillos el cordón

para la batería del coche

ADVERTENCIA: El conductor nunca debe ver

programas del televisor o del videobgrabadora

mientras está conduciendo un vehículo.

PRECAUCIÓN: Si usted usa la TV/VCR con el

motor del vehículo apagado, recargue la batería

del vehículo aprox. cada 4 horas de uso, para

evitar que ésta se agote. Cuando termine de usar

la TV/VCR, siempre desenchufe el cordón para

la batería del automóvil del zócalo del encende-

dor de cigarrillos.

Antena de VHF/UHF

para TV móvil

(no incluído)

Cordón para la batería

del automóvil

DC13.2V

ANT.

1)La antena de interiores incluída es adecuada para

usar cuando el vehículo está inmóvil. Para obtener

una mejor recepción en ruta, utilice una antena de

VHF/UHF para TV móvil de alta calidad.

2)Enchufe el cordón para batería de automóvil al conec-

tor DC13.2V (12V) en la parte posterior de la

INSTALACIÓN DE LAS PILAS

TV/VCR. Luego conecte el otro extremo en el zócalo

para el encendedor de cigarrillos del automóvil.

1)Abra la tapa del compartimiento de las pilas del

mando a distancia presionándola en el sentido de

la flecha.

2)Inserte 2 pilas tamaño “AA” en el compartimiento

de las pilas, en el sentido indicado por las marcas

de polaridad (+/-).

NOTAS:

Confirme que su vehículo tiene un sistema eléctrico

a tierra negativo de 13.2 (12) voltios.

Confirme que está usando sólo el cordón provisto

para la batería del automóvil. El uso de otro cordón

puede dañar su TV/VCR.

•

3)Vuelva a poner la tapa.

Asegúrese que no haya cenizas ni otro restos en el

zócalo del encendedor.

Asegúrese de introducir completamente el enchufe

del cordón de la batería del automóvil en el zócalo

del encendedor de cigarrillos.

•

Siempre desenchufe primero del zócalo del

encendedor de cigarrillos el cordón para la batería

del coche, antes de desconectarlo de la TV/VCR.

Antes de usar la alimentación de CA, usted debe

desconectar de la TV/VCR el cordón para la batería

del automóvil.

Solamente reemplace un fusible por otro del mismo

tipo 5A, 250V.

Asegúrese de que el cable de CA esté bobinado

como se muestra más abajo.

•

MODO DE ENTRADA EXTERNA

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los

cables de salida de audio/vídeo del equipo de repro-

ducción a las tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón

CHANNEL K o L hasta que “AUX” aparezca en la

pantalla.

Usted puede programar el temporizador para que

explore todos los canales que puedan recibirse en su

zona.

•

SELECCION DE IDIOMA

1 Enchufe el cordón de alimentación

del televisor/videograbadora

Enchufe el cordón de alimentación del

televisor/videograbadora en una toma de

CA estándar.

NOTA:

Si aparecen algunas cifras en la esquina

de la pantalla, pulse el botón POWER sin desench-

ufar el cordón de alimentación.

•

- 30 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

AJUSTE DE CANAL

A continuación, pulse el botón

F.FWD/B.

El sintonizador busca y memoriza

todos los canales activos en su

localidad.

–

Asegúrese de que ...

AGREGAR/BORRAR (CATV)

Pulse el botón POWER para encender el televi-

sor/videograbadora.

•

B AUTOPROGRAMACION DE CA.

NOTA: Esta función afecta sólo el idioma en el

menú de la pantalla y no la fuente de audio.

– M E N U –

2 Seleccione “LANGUAGE”

3 Después de buscar

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Pulse el botón MENU en el mando

El sintonizador se detiene en el canal memorizado

más bajo.

•

a distancia.

Pulse el botón PLAY/K o STOP/L

para señalar “LANGUAGE”.

Cuando se activa AUTOPROGRAMACION DE

CA, donde no hay entrada de señal del televisor,

aparecerá “NO HAY SEÑAL DE TV” en la pan-

talla después de terminar la búsqueda de canales.

Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”

El televisor/videograbadora puede reconocer los

•

Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS” con el botón F.FWD/B y pulse el

botón REW/s en el mando a distancia.

canales de TV para que sean canales de TV de

antena de cable con las condiciones de recepción.

En este caso, pruebe nuevamente con el prefijado

automático en las condiciones de recepción fina.

4 Salga del modo de idioma

Pulse el botón MENU en el mando a distancia para

volver al modo del televisor.

AJUSTE DEL RELOJ

NOTA: Si, por alguna razón, el menú está en español

o francés, pulse el botón MENU en el mando a distan-

cia, pulse el botón PLAY/K para señalar el “IDIOMA

(ESPAÑOL)” o “LANGAGE (FRANÇAIS)”, a con-

tinuación, pulse el botón F.FWD/B y pulse el botón

MENU en el mando a distancia.

Cerciórese...

La alimentación del televisor/videograbadora

deberá estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 6 de mayo de 2004

•

HORA: 5:40 PM

1)Pulse el botón MENU en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”.

AJUSTE DE CANAL

Puede programar el sintonizador para buscar todos

los canales que recibe en su localidad.

Luego, pulse el botón F.FWD/B.

NOTA: El canal preparado NO es necesario cuando

esté conectado a una caja de cable o caja de satélite.

Sólo tiene que seleccionar con el selector de canal

del televisor/videograbadora al canal de salida de la

caja de cabe o caja de satélite (por ejemplo el canal

CH3). Seleccione el canal a ver en la caja de cable o

caja de satélite.

2)Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”.

Luego, pulse el botón F.FWD/B.

3)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el mes deseado. (Ejemplo: Mayo - 05)

Luego, pulse el botón F.FWD/B.

4)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el día del mes deseado. (Ejemplo: 6 - 06)

Luego, pulse el botón F.FWD/B.

5)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el año deseado. (Ejemplo: 2004)

Luego, pulse el botón F.FWD/B.

6)Pulse el botón PLAY/K o STOP/L hasta que

aparezca la hora deseada. (Ejemplo: 5, PM)

Luego, pulse el botón F.FWD/B.

7)Pulse el botón PLAY/K o STOP/L hasta que

aparezca el minuto deseado. (Ejemplo: 40)

8)Pulse el botón MENU en el mando a distancia.

Aunque los segundos no se visualizan, éstos

empiezan a contar desde 00 cuando se pulsa

MENU en el mando a distancia. Utilice esta fun-

ción para sincronizar el reloj con la hora correcta.

Asegúrese de que ...

Pulse el botón POWER para encender el televi-

sor/videograbadora.

•

1 Seleccione “AJUSTE DE CANAL”

– M E N U –

Pulse el botón MENU en el mando

COMO PROGRAMAR

CONTROL DE IMAGEN

a distancia.

AJUSTE RELOJ

AJUSTE DE CANAL

AJUSTE DE USER

IDIOMA [ESPAÑOL]`

RETORNO A CERO

BUSQUEDA DE HORA

Pulse el botón PLAY/K o el botón

STOP/L para señalar “AJUSTE DE

CANAL”.

A continuación, pulse el botón F.FWD/B.

2 Empiece el prefijado automático

Pulse el botón PLAY/K o STOP/L para señalar

“AUTOPROGRAMACION DE CA”.

- 31 -

9J27

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR:

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE

PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE

UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,

please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-968-3429

http://www.funai-corp.com

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

0EMN02467

★★★★★

T4502UC

Download from Www.Somanuals.com. All Manuals Search And Download.

Shark Iron GI460 User Manual
Sharp CRT Television 27SF560 User Manual
Shenzhen High Power Tech Network Router H7920 User Manual
Sony Stereo Receiver 3 875 814 111 User Manual
Sony Tablet Accessory PRSAAC1 User Manual
Speco Technologies Security Camera CVC 7005EXTP User Manual
SSI America Stereo Amplifier 601620 User Manual
State Industries Electric Heater GPG85 540 NEA User Manual
Sylvania VCR C6240VE User Manual
Tanita Scale BF 558 User Manual