Sylvania TV DVD Combo SSL15D5 User Manual

POWER  
1-800-968-3429.  
SSL D  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9.Ventilation-Slots and openings in the cabinet and the back  
or bottom are provided for ventilation and to ensure reliable  
operation of the unit and to protect it from overheating, and  
these openings must not be blocked or covered. The open-  
ings should never be blocked by placing the unit on a bed,  
sofa, rug, or other similar surface. This unit should never be  
placed near or over a radiator or heat register. This unit  
should not be placed in a built-in installation such as a  
bookcase or rack unless proper ventilation is provided or  
the manufacturer’s instructions have been adhered to.  
14.Lightning-For added protection for this unit receiver dur-  
ing a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the unit due to lightning and power-line  
surges.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
10.Power Sources-This unit should be operated only from the  
type of power source indicated on the marking label. If you  
are not sure of the type of power supply to your home, con-  
sult your appliance dealer or local power company. For the  
units intended to operate from battery power, or other  
sources, refer to the operating instructions.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this unit through openings as they may touch danger-  
ous voltage points or short out parts that could result in a  
fire or electric shock. Never spill liquid of any kind on the  
unit.  
11.Grounding or Polarization-This unit is equipped with a  
polarized alternating-current line plug(a plug having one  
blade wider than the other). This plug will fit into the  
power outlet only one way. This is a safety feature. If you  
are unable to insert the plug fully into the outlet, try revers-  
ing the plug. If the plug should still fail to fit, contact your  
electrician to replace your obsolete outlet. Do not defeat the  
safety purpose of the polarized plug.  
18.Servicing-Do not attempt to service this unit yourself as  
opening or removing covers may expose you to dangerous  
voltage or other hazards. Refer all servicing to qualified  
service personnel.  
12.Power-Cord Protection-Power-supply cords should be  
routed so that they are not likely to be walked on or  
pinched by items placed upon or against them, paying par-  
ticular attention to cords at plugs, convenience receptacles,  
and the point where they exit from the appliance.  
19.Damage Requiring Service-Unplug this unit from the wall  
outlet and refer servicing to qualified service personnel  
under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
unit.  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the unit, be sure the antenna  
or cable system is grounded so as to provide some protec-  
tion against voltage surges and built-up static charges.  
Article 810 of the National Electrical Code, ANSI/NFPA  
No. 70, provides information with respect to proper  
grounding of the mast and supporting structure, grounding  
of the lead-in wire to an antenna discharge unit, size of  
grounding conductors, location of antenna-discharge unit,  
connection to grounding electrodes, and requirements for  
the grounding electrode. (Fig. A)  
c. If the unit has been exposed to rain or water.  
d. If the unit does not operate normally by following the oper-  
ating instructions. Adjust only those controls that are cov-  
ered by the operating instructions, as improper adjustment  
of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the unit to its normal operation.  
e. If the unit has been dropped or damaged in any way.  
f. When the unit exhibits a distinct change in performance,  
this indicates a need for service.  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
21.Safety Check-Upon completion of any service or repairs to  
this unit, ask the service technician to perform routine safe-  
ty checks to determine that the unit is in proper operating  
condition.  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
22.Heat-This unit product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
NEC  
-
NATIONAL ELECTRICAL CODE  
S2898A  
- 3 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LASER SAFETY  
Unauthorized copying, broadcasting, public performance  
and lending of discs are prohibited.  
This unit employs a laser. Only a qualified service person  
should remove the cover or attempt to service this device,  
due to possible eye injury.  
This product incorporates copyright protection technology  
that is protected by U.S. patents and other intellectual prop-  
erty rights. Use of this copyright protection technology must  
be authorized by Macrovision, and is intended for home and  
other limited viewing uses only unless otherwise authorized  
by Macrovision. Reverse engineering or disassembly is pro-  
hibited.  
CAUTION: USE OF CONTROLS OR ADJUSTMENTS  
OR PERFORMANCE OF PROCEDURES OTHER  
THAN THOSE SPECIFIED HEREIN MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
CAUTION: VISIBLE AND INVISIBLE LASER RADIA-  
TION WHEN OPEN AND INTERLOCK DEFEATED.  
DO NOT STARE INTO BEAM.  
FCC WARNING- This equipment may generate or use  
radio frequency energy. Changes or modifications to  
this equipment may cause harmful interference unless  
the modifications are expressly approved in the instruc-  
tion manual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change or modi-  
fication is made.  
LOCATION: INSIDE, NEAR THE DECK MECHA-  
NISM.  
This Class B digital apparatus complies with Canadian  
ICES-003.  
RADIO-TV INTERFERENCE  
Cet appareil numérique de la classe B est conforme à la  
This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reason-  
able protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful inter-  
ference to radio communications.  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
norme NMB-003 du Canada.  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,  
FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOC  
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS  
LARGE DE LA FICHE DANS LA BORNE CORRE-  
SPONDANTE DE LA PRISE ET POUSSER JUSQU’AU  
FOND.  
A NOTE ABOUT RECYCLING  
Batteries should never be thrown away or incinerated but  
disposed of in accordance with your local regulations con-  
cerning chemical wastes.  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment and  
receiver.  
3) Connect the equipment into an outlet on a circuit differ-  
ent from that to which the receiver is connected.  
4) Consult the dealer or an experienced radio/TV techni-  
cian for help.  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE  
TO RAIN OR MOISTURE.  
THIS SYMBOL INDICATES THAT  
DANGEROUS VOLTAGE  
CONSTITUTING A RISK OF ELECTRIC  
SHOCK IS PRESENT WITHIN THIS UNIT.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
THIS SYMBOL INDICATES THAT THERE  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
ARE IMPORTANT OPERATING AND  
SHOCK, DO NOT REMOVE COVER (OR BACK). NO  
MAINTENANCE INSTRUCTIONS IN THE  
USER SERVICEABLE PARTS INSIDE. REFER  
LITERATURE ACCOMPANYING THE  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
APPLIANCE.  
The caution marking is located on the rear of the cabinet.  
- 4 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some head-  
ings in this manual.  
For safe operation and satisfactory performance of  
your unit, keep the following in mind when selecting  
a place for its installation:  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
: Description refers to playback of DVD video discs  
(in the DVD mode).  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top or bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
: Description refers to playback of Audio CDs  
(in the DVD mode).  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the unit near strong magnetic fields.  
Avoid moving the unit to locations where tempera-  
: Description refers to playback of CDs with MP3  
files (in the DVD mode).  
ture differences are extreme.  
QUICK  
Be sure to remove a disc and unplug the AC power  
cord from the outlet before carrying the unit.  
: Description refers to the items to be set by the  
QUICK mode (in the DVD mode).  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
TILT STAND  
You can adjust the stand to change the angle of the  
TV (-5° to 10°).  
If by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
10°  
-5°  
Do not put your fingers or objects into the unit  
disc slot.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place  
or after heating a cold room or under conditions of  
high humidity. If a DVD is played in a unit which  
has moisture, it may damage the DVD and the unit.  
Therefore when the condensation occurs inside the  
unit, turn the unit on and allow at least 2 hours for  
the unit to dry out.  
- 5 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . .2  
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . .2  
SEARCH FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . .22  
TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . .22  
TITLE / CHAPTER SEARCH . . . . . . . . . . . . . . . . . . .22  
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . .23  
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
AVOID THE HAZARDS OF  
SPECIAL PLAYBACK FUNCTION . . . . . . . . . . . . . . . . .24  
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25  
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . .25  
ELECTRICAL SHOCK AND FIRE . . . . . . . . . . . . . . . .5  
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
SYMBOLS USED IN THIS MANUAL . . . . . . . . . . . . . .5  
TILT STAND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . .6  
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
CHANGING THE SETTINGS . . . . . . . . . . . . . . . . . . . . .26  
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . .26  
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . .26  
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . .26  
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . .27  
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . .27  
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . .27  
OPERATING CONTROLS AND FUNCTIONS . . . . . . . . . .8  
INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . .9  
PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . .10  
ANTENNA/CABLE CONNECTION . . . . . . . . . . . . . . .10  
EXTERNAL CONNECTION . . . . . . . . . . . . . . . . . . . . .11  
THE ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . .28  
TV SECTION  
CHANGING THE DVD SET UP ITEMS . . . . . . . . . . . . . .29  
CUSTOM MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . .29  
D LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . .29  
E DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . .30  
F AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . . . . .30  
TV OPERATION AND SETTINGS . . . . . . . . . . . . . . . . .12  
WATCHING A TV PROGRAM . . . . . . . . . . . . . . . . . .12  
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . . . . . . . .13  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . .14  
BACK LIGHT SETTING . . . . . . . . . . . . . . . . . . . . . . .14  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14  
CLOSED CAPTION SYSTEM . . . . . . . . . . . . . . . . . .15  
MTS (Multi-Channel Television Sound) System . . . . . .15  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16  
G
H
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . .31  
OTHER SETTINGS . . . . . . . . . . . . . . . . . . . . . . . .31  
INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32  
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . .33  
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36  
A
TV RATING SET UP . . . . . . . . . . . . . . . . . . . . . . .16  
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . .36  
B MPAA RATING SET UP . . . . . . . . . . . . . . . . . . . .17  
C CHANGE ACCESS CODE . . . . . . . . . . . . . . . . . .17  
MENU LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . .17  
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37  
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38  
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover  
DVD SECTION  
ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
UNPLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . .18  
PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . .20  
FAST FORWARD / FAST REVERSE . . . . . . . . . . . . .21  
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . .21  
ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
- 6 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES  
TV Mode  
MTS/SAP Tuner  
Infrared remote control  
Trilingual on screen TV setup display available in  
English, Spanish or French  
181 channel capability PLL frequency synthesizer  
tuner with direct station call  
(A converter may be necessary to view scrambled  
cable channels.)  
Auto power off system  
If there is no air signal input from the antenna ter-  
minal and no operation for 15 minutes, the unit  
will turn itself off automatically.  
Sleep timer  
Allows you to have the unit automatically turn off  
at a desired time.  
V-CHIP  
Enables parents to prevent their children from  
watching inappropriate material on TV.  
Closed Caption Decoder  
You may view specially labeled (cc) TV programs,  
movies, news, etc. with either a dialogue caption or  
text display added to the program.  
DVD Mode  
Dolby Digital sound  
Parental lock  
You can set the control level to limit playback of  
discs which may not be suitable for children.  
This unit can handle Dolby Digital surround sound  
having 5.1 channels when connected to a Dolby  
Digital decoder.  
Automatic detection of discs  
This unit automatically detects if the loaded disc is  
DVD, Audio CD or MP3 disc.  
Still/fast/slow/step playback  
Various playback modes are available including  
still pictures, fast forward/reverse, slow motion and  
step frames.  
On-screen display  
Information about the current operation can be dis-  
played on a TV screen, allowing you to confirm  
the currently active functions (such as program  
playback), on the TV screen using the remote con-  
trol.  
Random playback for Audio CD and MP3  
This unit can shuffle the order of tracks to play  
them in random order.  
Program playback for Audio CD and MP3  
You can program the order of tracks to play them  
in any desired order.  
Search  
Chapter search / Title search / Track search / Time  
search  
DVD menus in a desired language  
You can display DVD menus in a desired lan-  
guage, if available on a DVD.  
Repeat  
Chapter / Title / Track / Group / All / A-B  
Screen saver  
Zoom  
If the screen saver program is set to ON, it starts  
when there is no input from the unit for 5 minutes  
in stop mode.  
Allows you to enlarge video image.  
Marker  
The part designated by user can be called back.  
Subtitles in a desired language  
You can select a desired language for the display  
subtitles, if that language is available on a disc.  
Resume Play  
User can resume to playback from the part at  
which the play was stopped.  
Selecting a camera angle  
You can select the desired camera angle, if a disc  
contains sequences recorded from different angles.  
Virtual Surround  
Bit rate indication  
Choices for audio language and sound mode  
DRC (Dynamic range control)  
You can control the range of sound volume.  
You can select the desired audio language and  
sound mode, if different languages and modes are  
available on a disc.  
- 7 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING CONTROLS AND FUNCTIONS  
NOTE  
O
When you select DVD mode, press [SELECT], [PLAY ] or [EJECT A] first or insert a disc into the  
disc slot. Otherwise, the DVD features are not operated.  
- REMOTE CONTROL  
For DVD mode (P.28):  
ress to display the current status on the TV screen.  
P
9.SETUP button (P13, P.29)  
POWER PICTURE SELECT  
EJECT  
CH.  
Press to enter or exit the setup menu of TV/DVD.  
10. TITLE button (P.20)  
1
2
15  
16  
1
4
2
5
8
0
3
6
Press to display the title menu.  
17  
11. CLEAR button (P12, P.22)  
3
4
Press to clear/cancel a setting currently entered.  
Press to clear “DISC INSIDE” display.  
7
SLEEP  
9
+100  
VOL.  
18  
12. MODE button (P.25)  
+10  
Press to call up the program/random screen in  
stop mode.  
SKIP  
ZOOM  
MUTE  
19  
20  
21  
5
6
Press to call up the Black Level Setting/Virtual  
Surround screen during playback.  
PLAY  
STOP  
REV  
FWD  
13. SEARCH MODE button (P.22, P23)  
22  
DISC  
MENU  
Press to locate a desired point.  
PAUSE SLOW  
DISPLAY  
7
8
23  
24  
25  
14. AUDIO button (P.26)  
For TV mode (P.15): Press to select TV sound  
mode (STEREO/SAP/MONO).  
ENTER  
SETUP  
TITLE  
RETURN  
9
10  
11  
26  
27  
For DVD mode (P.26): Press to select a desired  
audio language (if available).  
CLEAR SEARCH MODE REPEAT  
A-B  
AUDIO SUBTITLE ANGLE  
MODE  
15. EJECT A button (P.19)  
12  
13  
14  
28  
29  
30  
Press to remove a disc from the unit.  
16. SELECT button (P.12)  
Press to select the TV mode, external input mode  
or DVD mode.  
[Fig. 1]  
17. CH. K /L buttons (P.12)  
1.POWER button (P.12)  
Press to turn the power on and off.  
2.PICTURE button (P.14)  
Press to adjust the picture.  
Press to select memorized channels.  
18. VOL. X /Y buttons (P.12)  
Press to control the volume level for the DVD  
and TV.  
3.Number buttons (P.13)  
19. MUTE button (P.12)  
Press to select a desired channel number directly.  
+100 button (For TV mode)  
Press to mute the sound or press it again to  
restore sound.  
Press to select channels higher than 99.  
+10 button (For DVD mode)  
20. ZOOM button (P.21)  
Press to enlarge the part of a DVD-reproduced  
image.  
Press to enter desired numbers higher than 9.  
4.SLEEP button (P.14)  
Press to set the Sleep Timer.  
5.SKIP H / G buttons (P.22)  
Press once to skip chapters/tracks to a desired point.  
6.PLAY O button (P.19)  
Press to playback the disc.  
7.PAUSE F button (P.20)  
Press to pause the current disc operation.  
8.DISPLAY button  
For TV mode (P.15):  
Press to display the current channel number on  
the TV screen.  
21. REV E button (P.21)  
Press to view the DVD picture in fast/slow  
reverse motion.  
FWD D button (P.21)  
Press to view in fast/slow forward motion.  
22. STOP C button (P.19)  
Press to stop operation of the disc.  
23. DISC MENU button (P.20)  
Calls up the DVD menu.  
– Calls up the file list in MP3 disc.  
24. ENTER button (P.16)  
Press to accept a setting.  
- 8 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28. ANGLE button (P.27)  
25.  
K
(Up) /  
L
(Down) / { (Left) / B (Right) buttons  
Press to change the camera angle to see the  
sequence being played back from a different angle  
(if available).  
Press to select or adjust menu items.  
26. RETURN button (P.27)  
Press to return to the previous screen in the setup  
menu.  
29. REPEAT button (P.24)  
Repeats playback of the current disc, title, chap-  
ter, group or track.  
27. A-B button (P.24)  
Press to repeat the playback of a selected section.  
30. SUBTITLE button (P.26)  
Press to select a desired subtitle language.  
- FRONT PANEL  
31. MENU button  
31 32 33  
34 35  
36 37  
38  
Press to enter or exit the setup menu of TV/DVD.  
32. STOP P button (P.19)  
Press to stop operation of the disc.  
MENU  
STOP  
PLAY  
EJECT  
VOLUME  
CHANNEL  
SELECT POWER  
C
B
A
L
K
L
K
33. PLAY B button (P.19)  
Press to playback of the disc.  
34. EJECT A button (P.19)  
Press to remove a disc from the unit.  
35. VOLUME X /Y buttons (P.12)  
Press to control the volume level for the DVD  
and TV.  
36. CHANNEL X /Y buttons (P.12)  
Press to select memorized channels.  
37. SELECT button (P.12)  
Press to select to TV mode, external input mode  
or DVD mode.  
POWER  
38. POWER button (P.12)  
Press to turn the power on and off.  
39  
39. Remote sensor window  
[Fig. 2]  
INSTALLING THE BATTERIES  
BATTERY PRECAUTIONS  
1 Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
Be sure to follow the correct polarity as indicated  
in the battery compartment. Reversed batteries  
may cause damage to the device.  
2 Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
Do not mix different types of batteries together  
(e.g. Alkaline and Carbon-Zinc) or old batteries  
with fresh ones.  
3 Replace the cover.  
If the device is not to be used for a long period of  
time, remove the batteries to prevent damage or  
injury from possible battery leakage.  
Do not try to recharge batteries not intended to be  
recharged; they can overheat and rupture.  
NOTE  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled  
with a universal remote control.  
If you decide to use a universal remote control with this unit, please be aware that the code number given  
may not operate this unit. In this case, please call the manufacturer of the universal remote control.  
- 9 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTION  
NOTE  
Cables used here are commercially available.  
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT jack  
before moving the unit.  
- ANTENNA/CABLE CONNECTION (WITH OR WITHOUT BOX)  
[Rear of this unit]  
Antenna  
Cable TV  
signal  
or  
L
UT  
O
ITA  
DIG  
O
DI  
AU  
L)  
XIA  
OA  
(C  
O
2
E
V
I
D
A
R
D
I
O
U
L
T
N
E
N
P
O
C
O
M
Y
Pb  
Pr  
Incoming cable from home Antenna /  
Cable Company (No Cable Box)  
R
I
O
D
A
U
L
1
O
E
I
D
S
V
O
E
I
D
V
-
V
I
D
E
O
T
N
N
A
Cable Box or  
Satellite Box*  
OR  
H
E
A
D
P
H
O
E
OUT  
IN  
ANT  
Incoming cable from Cable Company  
or Satellite Antenna  
*Some cable TV systems use scrambled signals and  
require a special converter to receive these channels.  
Consult your local cable company.  
IF YOU HAVE A JACK ON THE WALL  
Connect the TV to the wall-mounted antenna jack  
with on RF cable (commercially available).  
WHEN USING CABLE BOX/SATELLITE  
BOX  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown above.  
Channel selection must be made with the converter  
box or satellite box. This means that channels cannot  
be changed using the remote control of this unit.  
IF YOU HAVE A WIRED CABLE  
Connect the TV to the wired antenna cable.  
NOTE  
Bent pin  
Before plugging the antenna into the ANT jack of the unit, check that the pin is  
not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the  
ANT jack of the unit.  
Cable  
Plug  
(Needs to be  
straightened)  
(Straight pin)  
For CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides  
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding  
system of the building as close to the point of cable entry as practical.  
- 10 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONNECTION  
You can connect this unit to your own Audio/Video  
[Rear of this unit]  
equipment.  
Be sure to turn off the power to all components in  
the system before connecting another component.  
L
A
IT  
IG  
D
T
U
AUDIO  
O
IO  
D
U
A
L)  
IA  
X
A
O
(C  
I
D
E
O
2
V
R
Refer to the Owner’s Manuals for the equipments  
to be connected to the unit.  
I
O
D
U
A
L
VIDEO2  
C
O
M
P
O
Y
N
E
N
T
b
P
r
P
R
NOTE  
U
D
I
O
E
A
L
VIDEO1  
EO  
V
1
O
V
I
D
I
D
When you use external connections, select “VIDEO1” or  
“VIDEO2” by pressing [SELECT]. (Refer to page 12.)  
O
I
D
E
S
-
V
T
N
A
E
N
O
H
P
D
A
E
H
To use the VIDEO1 input jacks, select “VIDEO1”.  
To use the VIDEO2 input jacks, select “VIDEO2”.  
- VIDEO1 INPUT  
Use this connection if your own A/V equipment (e.g.  
VCR) has Video output and Audio out jacks. When  
using S-Video cable, better picture is available.  
ex.  
(IN)  
Audio Cable  
(OUT)  
R
AUDIO  
L
(IN)  
(IN)  
(OUT)  
(OUT)  
Video Cable  
OR  
VIDEO1  
EO  
VID  
Video Cassette  
Recorder  
S-VIDEO  
S-Video Cable  
NOTE  
If your own equipment is monaural (has only one Audio jack), connect the Audio cable to AUDIO L jack of this unit.  
If you connect Video jack and S-VIDEO jack simultaneously, the S-VIDEO jack is given priority over the VIDEO jack.  
- VIDEO2 INPUT  
Use this connection if your own A/V equipment (e.g.  
video camera, video game) has COMPONENT  
Video output (Y, Pb, Pr) jacks. You can enjoy the  
best picture with this connection.  
ex.  
VIDEO2  
R
Audio Cable  
AUDIO  
L
(IN)  
(OUT)  
(OUT)  
Video Camera  
COMPONENT  
Y
Component  
Video Cable  
Pb  
Pr  
(IN)  
Video Game  
- AUDIO OUTPUT  
You can enjoy DVD sound with more  
presence by connecting digital audio  
equipment such as Dolby Digital decoder.  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
Home Audio System  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
(OUT)  
Dolby Digital decoder  
NOTE  
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck.  
If connected to a Dolby Digital decoder, set “DOLBY DIGITALto “BITSTREAM” for audio output in the setup mode. (Refer to page 30.)  
Unless connected to a Dolby Digital decoder, set “DOLBY DIGITALto “PCM” for audio output in the setup mode. Playing  
a unit using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to page 30.)  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol  
are trademarks of Dolby Laboratories.  
- 11 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV SECTION  
TV OPERATION AND SETTINGS  
NOTE  
For channel number selection with number  
buttons:  
POWER PICTURE SELECT  
EJECT  
CH.  
To select single-digit channel number, press  
[0] first. (e.g. Press [0] [2] for channel 2.)  
1
4
2
5
8
0
3
6
To select cable channels which are higher  
than 99, press [+100/+10] first.  
(e.g. Press [+100/+10] [2] [5] for channel 125.)  
7
SLEEP  
9
+100  
VOL.  
X
Y
] to select the desired volume  
4 Use [VOL.  
/
+10  
level.  
SKIP  
ZOOM  
MUTE  
PLAY  
STOP  
VOL.  
REV  
FWD  
VOLUME 20  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
Press [MUTE] to instantly mute the sound.  
Press it again to restore the previous volume  
level.  
ENTER  
SETUP  
TITLE  
RETURN  
NOTE  
If you use [CH. K /L] in the DVD mode,  
Shaded buttons are used for following operation.  
you can change the TV channels. Even if you  
turn off the unit in the DVD mode, when you  
turn it on again, it will go into the TV mode.  
WATCHING A TV PROGRAM  
1 Plug the power cord into a standard  
TO WATCH CABLE OR SATELLITE  
CHANNEL  
AC outlet.  
If the unit is connected to a cable box or satellite  
box, use [CH. K /L] to select CH3 or CH4 accord-  
ing to the output channel setting of the device and  
select desired channel on that device.  
NOTE  
If any digits are displayed in the corner of the  
screen, press [POWER] without unplugging  
the power cord.  
TO WATCH EXTERNAL INPUT  
When an external equipment is connected to the front  
AUDIO/VIDEO input jacks, press [SELECT] or  
[CH. K /L] repeatedly until “VIDEO1” or  
“VIDEO2” appears on the screen.  
2 Press [POWER] to turn on the unit.  
POWER  
3 Use [CH. K /L] to select the desired channel  
NOTE  
number.  
If a disc is inside the unit, “DISC INSIDE” mes-  
sage is displayed on the screen for 10 seconds.  
CH.  
or  
Use the Number buttons to enter the desired  
DISC INSIDE  
channel number.  
To clear the message instantly, press [CLEAR].  
1
4
7
2
5
8
3
6
9
+100  
0
+10  
- 12 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDING/DELETING CHANNELS  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you can  
add the deleted channel into the memory again.)  
CHANNEL SET UP  
AUTO CHANNEL PROGRAMMING  
As the initial setting, this unit has memorized all  
channels, including the ones not available in your  
area. This feature automatically puts only available  
channels into the memory.  
1 Press [SETUP] then press [  
K] or [L] to point  
to “CHANNEL SET UP”.  
- TV SET UP -  
1 Press [SETUP] then press [  
K] or [L] to point  
B
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
BACK LIGHT [BRIGHT]  
SETUP  
to “CHANNEL SET UP”.  
- TV SET UP -  
B
CHANNEL SET UP  
V-CHIP SET UP  
SETUP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
BACK LIGHT [BRIGHT]  
2 Press [ENTER] then press [  
K] or [L] to point  
to “ADD/DELETE CH”.  
– CHANNEL SET UP –  
2 Press [ENTER] then press [  
K] or [L] to point  
B
ADD / DELETE CH (CATV)  
AUTO PRESET CH  
ENTER  
to “AUTO PRESET CH”.  
– CHANNEL SET UP –  
ADD / DELETE CH (CATV)  
AUTO PRESET CH  
B
ENTER  
3 Press [ENTER] then press the Number but-  
tons or [CH. K /L] to select the desired  
channel number.  
3 Press [ENTER].  
15  
1
4
7
2
5
8
3
6
ENTER  
ENTER  
9
The tuner scans and memorizes all the active  
channels in your area.  
The tuner stops on the lowest memorized channel.  
+100  
0
+10  
ADD/DELETE  
4 Press [ENTER] then the channel number  
turned to red. The channel is deleted from  
memory. If the channel number turned to  
blue, the channel is added into memory.  
NOTE  
When “AUTO PRESET CH” is activated  
where there is no TV signal input, “NO TV  
SIGNALwill appear on the display after the  
completion of channel scanning.  
ENTER  
To delete another channel, repeat steps 3 to 4.  
If you press [ENTER] again, the channel is  
memorized again.  
The unit may recognize CATV channels to be  
TV channels if reception condition is poor. In  
this case, check the antenna connection and try  
“AUTO PRESET CH” again when reception  
conditions are better.  
Channel memory programming is NOT nec-  
essary when connected to a cable box or satel-  
lite box. Just select the channel for cable box  
or satellite input (ex. CH3) on the unit, then  
select your desired channel on the cable box  
or satellite box.  
Added channel : Light blue  
Deleted channel : Light red  
5 Press [SETUP] to exit the menu.  
SETUP  
NOTE  
To confirm that channel(s) has been deleted  
or added, use [CH. K /L].  
- 13 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POWER PICTURE SELECT  
EJECT  
NOTE  
The picture control display will disapper automati-  
cally after 10 seconds unless you press any buttons.  
3
SLEEP  
0
+10  
SKIP  
ZOOM  
MUTE  
BACK LIGHT SETTING  
PLAY  
STOP  
1 Press [SETUP] then press [  
K] or [L] to point  
REV  
FWD  
to “BACK LIGHT”.  
- TV SET UP -  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
BACK LIGHT [BRIGHT]  
SETUP  
B
ENTER  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
2 Press [ENTER] then press [s] or [B] to  
select to “BRIGHT”, “NORMALor “DARK”.  
AUDIO SUBTITLE ANGLE  
MODE  
ENTER  
Shaded buttons are used for following operation.  
3 Press [SETUP].  
SETUP  
PICTURE CONTROL  
The unit’s picture controls, brightness, contrast,  
color, tint and sharpness, are preset to factory speci-  
fications. Although they are usually the best, you  
may need to make some further adjustments for a  
more natural looking image.  
SLEEP TIMER  
The Sleep Timer function turns off the unit without  
using [POWER] after a desired period of time.  
1 Press [PICTURE] then press [  
K] or [L] to  
1 Press [SLEEP].  
select the desired control “BRIGHTNESS”,  
“CONTRAST”, “COLOR”, “TINT” or “SHARP-  
NESS”.  
SLEEP  
PICTURE  
SLEEP 0 MINUTE  
BRIGHTNESS  
-
+
2 Press [SLEEP] repeatedly until the desired  
sleep time is displayed.  
2 Press  
[s] or [B] to adjust to your desired  
level within 5 seconds.  
SLEEP  
Each press increases the time by 10 minutes up  
to 90 minutes.  
After 5 seconds, the Sleep Timer setting will  
disappear automatically.  
If you select “SLEEP 0 MINUTE”, Sleep Timer  
setting is cancelled.  
BRIGHTNESS  
CONTRAST  
COLOR  
to decrease  
to increase  
brightness  
to increase  
contrast  
brightness  
to decrease  
contrast  
to pale  
to brilliant  
TINT  
SHARPNESS  
to purple  
to soft  
to green  
to clear  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
- 14 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE  
CLOSED CAPTION SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news and pre-recorded tapes with either a  
dialogue caption or text display.  
Even if there is a power failure of any  
kind, the unit will retain its memory for  
this feature.  
CAPTION mode: You can watch dramas, movies and  
news while captioning the dialogues and the contents  
of news.  
TEXT mode: You can watch half screen text informa-  
tion if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is usually  
used for a second language if available.  
MTS (Multi-Channel Television  
Sound) System  
TO SELECT TV SOUND MODE  
1 Press [AUDIO] repeatedly to select the MTS  
output mode.  
NOTE  
Not all programs are broadcasted with closed  
AUDIO  
captions. Your unit is designed to provide error  
free closed captions from high quality antenna,  
cable and VCR signals. Conversely, poor quality  
signals are likely to result in caption errors or no  
captions at all. Common signal conditions which  
may cause caption errors are listed below:  
STEREO  
The output mode changes as described below  
every time you press [AUDIO].  
STEREO  
SAP*  
MONO  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter  
* Second Audio Program (SAP):  
Sometimes broadcasters add another channel of  
audio to the programs they air. This is usually a  
secondary language or perhaps a radio station.  
After 5 seconds, the current audio status will  
disappear from the TV screen.  
If the unit displays a black box on the TV screen,  
this means that the unit is set to the TEXT mode.  
To clear screen, select “CAPTION1”, “CAPTION2”  
or “OFF”.  
NOTE  
The initial setting is “STEREO”.  
This setting is saved even if the unit is turned  
off or the AC cord is unplugged.  
TO CHECK THE SOUND STATUS  
By pressing [DISPLAY], the status shown below  
will appear on the display when you receive a broad-  
cast on the unit tuner channel you are watching.  
1 Press [SETUP] then press [K] or [L] to point  
to “CAPTION”.  
- TV SET UP -  
CH 123  
STEREO/SAP  
CHANNEL SET UP  
SETUP  
V-CHIP SET UP  
3)  
2)  
1)  
LANGUAGE [ENGLISH]  
B
CAPTION  
[OFF]  
BACK LIGHT [BRIGHT]  
2 Press [ENTER] repeatedly to select the  
desired caption menu “CAPTION1”,  
“CAPTION2”, “TEXT1” or “TEXT2”.  
- TV SET UP -  
1) When a program is broadcasted in stereo,  
“STEREO” appears on the TV screen.  
CHANNEL SET UP  
V-CHIP SET UP  
2) When a program is broadcasted in second audio,  
LANGUAGE [ENGLISH]  
ENTER  
[CAPTION1]  
B
CAPTION  
“SAP” appears on the TV screen.  
BACK LIGHT [BRIGHT]  
3) When a program is broadcasted both in stereo and  
second audio, “STEREO/SAP” appears on the  
TV screen.  
If you select “OFF”, Closed Caption System set-  
ting is cancelled.  
3 Press [SETUP] to exit the menu.  
SETUP  
- 15 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV RATING SET UP  
1
4
2
5
8
0
3
6
A
CH.  
Follow steps to in the V-CHIP SET UP.  
1
3
7
SLEEP  
9
+100  
4 Press [K] or [L] to select the desired TV rat-  
ing to be blocked then press [ENTER] repeat-  
edly to set “BLOCK” or “VIEW”.  
VOL.  
+10  
ZOOM  
SKIP  
MUTE  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
(
)
PLAY  
STOP  
ENTER  
)
)
)
REV  
FWD  
(
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
Selection  
TV-Y  
TV-Y7  
TV-G  
TV-PG  
TV-14  
Rating Category Explanations  
Appropriate for all children  
Appropriate for children seven and older  
General Audience  
Parental Guidance suggested  
Unsuitable for children under 14  
ENTER  
SETUP  
TITLE  
RETURN  
Shaded buttons are used for following operation.  
TV-MA Mature audience only  
V-CHIP SET UP  
NOTE  
V-CHIP SET UP  
This feature enables parents to prevent their children  
from watching inappropriate material on TV. When  
you try to access a program which is blocked, “PRO-  
TECTED PROGRAM by ...message appears on  
the TV screen.  
When you select a rating and set it to  
“BLOCK”, the higher ratings will be blocked  
automatically. The lower ratings will be avail-  
able for viewing.  
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV )  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
1 Press [SETUP] then press [  
K] or [L] to point  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
to “V-CHIP SET UP”.  
- TV SET UP -  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
BACK LIGHT [BRIGHT]  
B
SETUP  
When you set the lowest rating to “VIEW”, all  
other ratings will automatically be available  
for viewing.  
2 Press [ENTER] then press the Number  
5 When you select the ratings of TV-Y7, TV-PG,  
TV-14 or TV-MA you will have the option of  
setting sub rating categories.  
Buttons to enter the access code.  
ACCESS CODE  
1
4
7
2
5
8
3
6
9
Press [K] or [L] to select a rating with sub-  
ratings you wish to block, then press  
[ENTER] twice.  
_
_
_
_
ENTER  
0
Press [K] or [L] to select a sub-rating, then  
press [ENTER] to set it to “BLOCK” or “VIEW”.  
For the first time set-up or in the event the unit  
has lost power, enter the default code of 0000.  
Selection  
TV-Y7  
FV  
Rating Category Explanations  
3 Press [K] or [L] to select “TV RATING”,  
MPAA RATING” or “CHANGE CODE” then  
Fantasy Violence  
press [ENTER].  
TV-PG, TV-14, TV-MA  
– V-CHIP SET UP –  
D
L
S
Suggestive Dialog (TV-PG, TV-14 only)  
B TV RATING  
MPAA RATING  
Coarse Language  
Sexual Situation  
Violence  
CHANGE CODE  
ENTER  
V
NOTE  
TV RATING:  
See A TV RATING SET UP  
The blocked sub-ratings will appear next to  
the rating category in the “TV RATING”  
menu.  
MPAA RATING: See  
CHANGE CODE: See  
MPAA RATING SET UP  
CHANGE ACCESS CODE  
B
C
- 16 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Make sure you enter exactly the same new code  
in the “CONFIRM CODE” space as one in the  
“NEW CODE” space. If they are different, the  
“NEW CODE” space is cleared for redoing.  
6 Press [SETUP] to exit the menu.  
SETUP  
NOTE  
5 Press [SETUP] to exit the menu.  
To change the rating, the TV must be turned  
SETUP  
to an unprotected program. If “PROTECT-  
ED PROGRAM by ...appears on the  
screen, please change the channel to a station  
that is not protected.  
NOTE  
Your personal access code will be erased and  
will return to the default (0000) when a  
power failure occurs or when you turn off the  
power using a wall switch. If you have for-  
gotten the code, unplug the power cord for 10  
seconds to restore the access code to 0000.  
MPAA RATING SET UP  
B
Follow steps to in the V-CHIP SET UP on page  
1
3
16.  
4 Press [K] or [L] to point to your desired item,  
then press [ENTER] to select “BLOCK” or  
“VIEW”.  
MENU LANGUAGE  
1 Press [SETUP] then press [K] or [L] to point  
G
[VIEW]  
to “LANGUAGE”.  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
- TV SET UP -  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
BACK LIGHT [BRIGHT]  
B
ENTER  
Selection  
G
Rating Category Explanations  
General Audience  
PG  
PG-13  
R
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
2 Press [ENTER] repeatedly to select  
“ENGLISH”, “ESPAÑOL= Spanish or  
“FRANÇAIS”= French.  
ENTER  
NC-17  
X
Mature audience only  
3 Press [SETUP] to exit the menu.  
When you select a rating and set it to “BLOCK”,  
the higher ratings will be blocked automatically.  
The lower ratings will be available for viewing.  
When you set the lowest rating to “VIEW”, all other  
ratings will automatically be available for viewing.  
SETUP  
NOTE  
This function effects only the language on the  
screen menu and not the audio source.  
5 Press [SETUP] to exit the menu.  
If for some reason the menu is in Spanish or  
SETUP  
French, press [SETUP], press [K] or [L] to  
point to “IDIOMA [ESPAÑOL]” or “LAN-  
GAGE [FRANÇAIS]”, then press [ENTER]  
repeatedly to select desired language, then  
press [SETUP].  
CHANGE ACCESS CODE  
C
Follow steps to in the V-CHIP SET UP on page  
1
3
16.  
4 Press the number buttons to enter your  
desired access code in the “NEW CODE”  
space, then enter the same code in the  
“CONFIRM CODE” space. When completed,  
the menu will return to “V-CHIP SET UP”.  
NEW CODE  
1
4
7
2
5
8
3
6
9
X X X X  
CONFIRM CODE  
_
_
_
_
0
- 17 -  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD SECTION  
ABOUT THE DISCS  
PLAYABLE DISCS  
Recorded  
signals  
Playable  
discs  
Disc size  
Disc type  
Title 1  
Region code  
Mark (logo)  
DVD-Video  
* 1,2,4,6,10,11  
or  
DVD-RW  
DVD-R  
* 1,3,4,5,  
6,7,9,10  
Example  
Title 2  
-
-
Digital video 5 inches  
(MPEG2)  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2  
(12cm)  
DVD+RW  
DVD+R  
* 1,3,4,5,  
6,8,9,10  
Audio CD  
* 4,6,10  
-
-
Digital audio  
Audio CD  
MP3  
Example  
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6  
5 inches  
(12cm)  
CD-RW  
CD-R  
* 4,5,6,9,10  
Example  
Digital audio  
Group 1  
Group 2  
or  
MP3  
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6  
is a trademark of DVD Format/Logo Licensing Corporation.  
If you cannot play back a disc which bears one of the marks above, check the following notes.  
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.  
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.  
*3: Discs recorded in the VR (Video Recording) format cannot be played back.  
*4: Scratched or stained discs may not be played back.  
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the  
recorder or special properties of discs.  
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not  
play them back. Even if they are played back, the sound or video quality will be compromised.  
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD recorder. However, depend-  
ing on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth,  
etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.  
*8: Only the discs recorded in the video format and finalized can be played back.  
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be  
played back at all or normally (the picture or sound may not be smooth, etc.).  
3
*9: If there is too much recording space left on a disc (the used portion is less than 2- / " (55mm) across), it may not play back properly.  
16  
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.  
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-  
mat can only be played back on unit with the same region code.  
UNPLAYABLE DISCS  
NEVER play back the following discs. Otherwise, the unit may result in malfunction.  
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /  
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers  
Never insert a disc which is broken or whose form is abnormal (other than 5 inch (12cm) round disc).  
On the following disc, the sound MAY NOT be heard.  
Super Audio CD  
NOTE  
Only the sound recorded on the normal CD layer can be delivered.  
The sound recorded on the high density Super Audio CD layer cannot be delivered.  
Any other discs without compatibility indications  
EN  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A DISC  
POWER PICTURE SELECT  
EJECT  
NOTE  
When the DVD mode has been switched to the  
TV mode, the DVD mode shuts down first and  
then the TV picture and sound appears in about  
4 seconds. Similarly, when [POWER] is  
pressed to turn off in the DVD mode, this mode  
shuts down first and then the unit is turned off.  
3
SKIP  
ZOOM  
MUTE  
” may appear at the top-right on the TV  
PLAY  
STOP  
REV  
FWD  
screen during operation, warning that a pro-  
hibited operation has been encountered by the  
DVD or the disc.  
With DVDs that use titles for playback pro-  
gram signals, playback may start from the  
second title or it may skip these titles.  
During the playback of a two layered disc,  
pictures may stop for a moment. This happens  
when the 1st layer switches to the 2nd layer.  
This is not a malfunction.  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
ENTER  
SETUP  
TITLE  
RETURN  
Shaded buttons are used for following operation.  
BASIC PLAYBACK  
GETTING STARTED  
MP3 PLAYBACK  
1 In stop mode, press [DISC MENU], then press  
K
L
[ ] or [ ] to select the desired group or track.  
Turn on the power of amplifier and any other compo-  
nents, if necessary.  
DISC  
MENU  
folder name 1  
folder name 2  
folder name 3  
folder name 4  
file name 1  
file name 2  
file name 3  
1 Press [POWER] then the power will turn on.  
POWER  
folder name 1  
2 Open the disc door manually.  
If a group is selected, press [B] or [ENTER] to go  
on to the track selection screen. Press [s] to go  
back to previous screen.(except for the top page.)  
ER  
POW  
CT  
SELE  
NEL  
CHAN  
V
OLU  
ME  
K
EJECT  
L
PLA  
Y
K
STOP  
L
MENU  
A
If a track is selected, press [ENTER] to start  
B
C
playing tracks. Starting from the one you’ve just  
chosen the subsequent tracks will be played.  
3
Insert a disc with the label facing back of the unit to  
start playing it. By simply placing the disc gently into  
the slot, it will be loaded automatically.  
If the entire file list cannot be displayed at once  
on a screen, “n” appears to go to the next page.  
Press [TITLE] to return to the top file of the  
highest hierarchy in the program and file list.  
2 Press [STOP C] to stop playback.  
STOP  
ER  
POW  
CT  
SELE  
NEL  
CHAN  
V
OLU  
ME  
K
EJECT  
L
PLA  
Y
K
STOP  
L
MENU  
A
B
C
NOTE  
Playback will start from the first chapter/track of the disc.  
If the playback does not start automatically,  
press [PLAY O].  
When you playback a DVD which features a  
title menu, it may appear on the screen. In this  
case, refer to “TITLE MENU” on page 20.  
Folders are known as Groups; files are known as Tracks.  
MP3 files are accompanied by  
3
icon.  
Maximum of 255 folders can be recognized.  
Maximum of 999 files can be recognized.  
Up to 8 hierarchies can be created.  
This unit recommends the use of files recorded  
at the below specifications:  
Sampling frequency: 44.1kHz or 48kHz  
4 Press [STOP C] to stop playback.  
Constant bit rate: 32kbps ~ 320kbps  
STOP  
For MP3 file recorded in Variable Bit Rate (VBR),  
the unit may not display the actual elapsed time.  
5
Press [EJECT A] to remove the disc from the unit.  
EJECT  
EN  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISC MENU  
RESUME  
1 Press [DISC MENU].  
1 During playback, press [STOP C].  
DISC  
MENU  
Resume ON  
The DVD main menu will appear.  
If the feature is not available,  
appear on the TV screen.  
STOP  
Press ’PLAY’ to play from here.  
To play the beginning,  
press ’STOP’ first and then ’PLAY’.  
symbol may  
If disc menu is available on the disc, audio lan-  
guage, subtitle options, chapters for the title and  
other options will appear for selection.  
(Example: DVD or Audio CD)  
Resume message will appear on the TV screen.  
2 Press [K], [L], [s] or [B] to select an item  
and press [ENTER] to confirm selection.  
2 Press [PLAY O], playback will resume from  
the point at which playback was stopped.  
ENTER  
PLAY  
To cancel resume, press [STOP C] twice.  
For MP3, playback will resume from the begin-  
TITLE MENU  
ning of the current track.  
The resume information stays on even when the  
power is turned off.  
1 Press [TITLE].  
PAUSE  
TITLE  
The title menu will appear.  
If the feature is not available,  
appear on the TV screen.  
symbol may  
1 During playback, press [PAUSE F].  
PAUSE  
2 Press [K], [L], [s] or [B] to select an item  
then press [ENTER] to confirm selection.  
Playback will pause and sound will be muted.  
ENTER  
2 To continue playback, press [PLAY O].  
PLAY  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
STEP BY STEP PLAYBACK  
Press [DISC MENU] to call up the DVD menu or  
press [TITLE] to call up the title menu.  
NOTE  
1 During playback, press [PAUSE F].  
Contents of menu and corresponding menu  
operations may vary between discs. Refer to  
the manual accompanying the disc for details.  
PAUSE  
Playback will pause and sound will be muted.  
2 The disc goes forward by one frame each  
time [PAUSE F] is pressed.  
PAUSE  
3
To exit step by step playback, press [PLAY O].  
PLAY  
EN  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FAST FORWARD /  
FAST REVERSE  
ZOOM  
The Zoom function allows you to enlarge the video  
image and to pan through the enlarged image.  
1 During playback, press [FWD D] or  
[REV E].  
1 Press [ZOOM] during playback.  
REV  
FWD  
ZOOM  
SLOW  
Playback will continue.  
D 1” or E 1” appears on the screen.  
2 Press [ZOOM] repeatedly to select the  
required zoom factor: ZOOM1, ZOOM2,  
ZOOM3 or OFF.  
2 To select another speed, repeat step 1 until  
your required speed number appears on the  
screen.  
ZOOM  
For DVDs, fast forward/reverse search speed is  
different depending on the disc. Approximate  
speed is 1(×2), 2(×8), 3(×20), 4(×50) and  
5(×100).  
3 Press [K], [L], [s] or [B] to move the  
zoomed picture across the screen.  
For Audio CDs and MP3 approximate speed is  
1(×2), 2(×8) and 3(×30).  
3
To return to normal playback, press [PLAY O].  
PLAY  
4 To exit zoom mode, press [ZOOM] to OFF.  
ZOOM  
SLOW FORWARD /  
SLOW REVERSE  
NOTE  
Zooming function does not work while disc  
menu is shown.  
Zooming function is not available on some  
discs.  
It may take several seconds to slide the  
zoomed picture.  
1 During playback, press [PAUSE F].  
PAUSE  
The picture may be distorted if you operate  
other functions repeatedly (ex. [PAUSE F] or  
[REV E], etc.) in the zoom mode.  
2 Press [FWD D] or [REV E].  
REV  
FWD  
SLOW  
1” or “  
1” appears on the screen.  
3 To select another speed, repeat step 2 until  
your required speed number appears on the  
screen.  
Slow forward or reverse speed varies with the  
disc. Approximate speed is 1(1/16), 2(1/8) and  
3(1/2).  
4
To return to normal playback, press [PLAY O].  
PLAY  
EN  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEARCH FUNCTION  
2 Within 30 seconds, select the desired track  
1
2
5
8
0
3
CH.  
number using the Number buttons.  
4
6
1
4
7
2
5
8
3
6
9
7
SLEEP  
9
+100  
VOL.  
+10  
0
SKIP  
ZOOM  
MUTE  
To select single-digit track number, press [0]  
first if the total number of track in the disc is 10  
or more. (e.g. Press [0] [3] for track number 3.)  
Playback will start at the selected track.  
PLAY  
STOP  
REV  
FWD  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
Using [SKIP H / G  
]
During playback, press [SKIP G] to move the next  
track. Press it repeatedly to skip subsequent tracks.  
Press [SKIP H] to go back to beginning of the cur-  
rent track. Press it repeatedly to go to the previous  
tracks.  
ENTER  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
If [SKIP H / G] is pressed while the play-  
back is paused, the playback will be paused  
again after skipping to the next track.  
Shaded buttons are used for following operation.  
NOTE  
TRACK SEARCH  
[SKIP H / G] are not operative when  
playback is stopped.  
There are three ways to begin playback on an Audio  
CD and MP3 at a specific track.  
TITLE / CHAPTER SEARCH  
Using the number buttons  
1 Press the Number buttons to enter the  
desired track number.  
1 Press [SEARCH MODE] once for the Chapter  
search, twice for the Title search during play-  
back.  
1
4
7
2
5
8
3
6
9
+100  
_/2  
SEARCH MODE  
0
+10  
once  
Playback will start at the selected track.  
To select single-digit track number, press single  
number. (e.g. Press [3] for track number 3.)  
To select track numbers which are higher than 9,  
press [+100/+10] first.  
2 Within 30 seconds, enter the desired chapter/  
title number using the Number buttons.  
1
4
7
2
5
8
3
6
9
(e.g. Press [+100/+10] [2] [5] for track number  
25.)  
0
Using [SEARCH MODE]  
Playback will start at the selected chapter or  
title.  
Press [CLEAR] to erase the incorrect input.  
To select single-digit chapter/title number, press  
[0] first if the total number of chapter/title in the  
disc 10 or more. (e.g. Press [0] [2] for  
chapter/title 2.)  
1 Press [SEARCH MODE].  
SEARCH MODE  
The track search display appears.  
EN  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIME SEARCH  
MARKER SETUP SCREEN  
Use markers to memorize your favorite places on a disc.  
1 During playback, press [SEARCH MODE]  
repeatedly to display the Time Search on the  
TV screen.  
1 Press [SEARCH MODE] repeatedly during  
playback to display the Marker screen.  
_:_ _:_ _ TOTAL 1:29:00  
SEARCH MODE repeatedly  
1
2
3
4
5
6
7
8
9
10 AC  
SEARCH MODE  
_ _  
_
_:_ _:_ _  
repeatedly  
2 Within 30 seconds, enter a desired disc time  
2 Press [s] or [B] to select 1, 2, 3, 4, 5, 6, 7,  
using the Number buttons.  
8, 9, or 10 and ensure that “  
:
:
- - - - - - - -  
appears in the display.  
1
4
7
2
5
8
3
6
9
0
3 When you reach the desired point, press  
Playback will start at the specified time.  
Press [CLEAR] to erase the incorrect input.  
When there is no need to enter a number, “0”  
appears automatically. For example,  
[ENTER].  
ENTER  
“ 0 : 0  
:
” appears in the Time Search display  
- - -  
The Title or Track and elapsed playing time will  
appear in the TV screen.  
if the total time of the track or title is less than  
10 minutes.  
4 To return to the Marker later, press [SEARCH  
MODE] repeatedly during playback to display  
the Marker screen. Then press [s] or [B] to  
choose the desired marker, then press  
[ENTER].  
SEARCH MODE  
ENTER  
repeatedly  
NOTE  
Operations which erase all Markers:  
– Turning off the power.  
– Ejecting a disc.  
– Pressing [SELECT].  
Selecting “AC” at step 2 and pressing [ENTER].  
To clear a marker:  
– Press [s] or [B] to select a cursor on to the  
marker number and press [CLEAR].  
You can mark up to 10 points.  
5 Press [SEARCH MODE] or [RETURN] to  
exit.  
SEARCH MODE  
EN  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL PLAYBACK FUNCTION  
For MP3  
PLAY  
REV  
FWD  
STOP  
1 Press [REPEAT] during playback.  
DISC  
MENU  
REPEAT  
PAUSE SLOW  
DISPLAY  
The repeat mode changes as described below  
every time you press the button.  
ENTER  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
TRACK  
(current track  
repeat)  
GROUP  
(current group  
repeat)  
ALL  
(entire disc  
repeat)  
OFF  
(repeat off)  
AUDIO SUBTITLE ANGLE  
MODE  
Shaded buttons are used for following operation.  
NOTE  
Repeat setting will be cleared when moving  
to other track.  
REPEAT  
REPEAT is available only during playback.  
A-B REPEAT  
For DVD-Vs  
1 To activate the repeat function, press [REPEAT]  
during playback.  
1 Press [A-B] at your chosen starting point.  
REPEAT  
A-B  
The repeat mode changes as described below  
every time you press the button.  
A-” appears briefly on the TV screen.  
2 Press [A-B] again at your chosen end point.  
CHAPTER  
TITLE  
OFF  
A-B  
(repeat off)  
(current chapter repeat) (current title repeat)  
A-B” appears briefly on the TV screen, and  
the repeat sequence begins.  
NOTE  
3 To exit the sequence, press [A-B].  
Repeat Title/Chapter is not available with  
some scenes.  
A-B  
The REPEAT setting will be cleared when  
moving to other title or chapter.  
NOTE  
The A-B repeat section can only be set within  
the current title (for DVDs) or current track  
(for Audio CDs).  
For Audio CDs  
A-B repeat is not available with some scenes in DVD.  
To cancel the A point which was set, press  
[CLEAR].  
A-B repeat playback does not function during  
title, chapter, track or all repeat playback.  
1 To activate the repeat function, press [REPEAT]  
during playback.  
REPEAT  
The repeat mode changes as described below  
every time you press the button.  
TRACK  
(current track repeat)  
ALL  
OFF  
(repeat off)  
(entire disc repeat)  
NOTE  
Repeat setting will be cleared when moving  
to other track.  
Repeat playback does not function during A-  
B repeat playback.  
EN  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROGRAM  
RANDOM PLAYBACK  
You may determine the order in which tracks will play. This function shuffles the playing order of tracks  
instead of playback in the sequence.  
1 In stop mode, press [MODE].  
1 In stop mode, press [MODE] twice.  
MODE  
RANDOM  
CD-DA  
TOTAL 0:45:55  
The “PROGRAM” screen will appear.  
MODE  
RANDOM PROGRAM  
no indication  
twice  
-
-
-
-
K
L
2 Press [ ] or [ ] to select a track, then press  
PLAY  
[ENTER].  
“RANDOM” screen appears.  
TOTAL 1:03:30  
1
5
3:30  
5:10  
10 4:20  
11 3:00  
12 3:20  
17 4:10  
22 2:50  
2/3  
2 Press [PLAY O] to start random playback.  
ENTER  
1/4  
PLAY  
NOTE  
Press [CLEAR] to erase the most recently  
entered track.  
If the entire Program cannot be displayed at  
once on a screen, Gappears to go to the next  
page and Happears to go back to the previ-  
ous page.  
If you like to repeat the current track in the ran-  
dom selection, press [REPEAT] several times  
until “  
you like to repeat the entire random selection  
press [REPEAT] several times until “  
appears during playback.  
TRACK” appears during playback. If  
ALL”  
While an MP3 folder is open:  
Press [ B] when you want to go to the next  
hierarchy.  
Press [s] when you want to go back to the  
previous hierarchy.  
3 Repeat step 2 until you have selected all the  
tracks you want to play in the program.  
4
Press [PLAY O] to play the programmed tracks.  
PLAY  
NOTE  
While the program is being played back,  
pressing [STOP C] works as follows.  
Press [STOP C] once and then [PLAY O]  
again, playback will restart from the point where  
[STOP C] was pressed (MP3: from the begin-  
ning of the current track). (Program continued)  
Press [STOP C] twice and then [PLAY O]  
again, playback will restart from the track in  
the usual way. (Program canceled)  
Up to 99 tracks can be entered.  
To erase all tracks in the program at once, select  
“ALL CLEAR” at the bottom of the list at step 2.  
If you like to repeat the current track in the  
program, press [REPEAT] several times until  
TRACK” appears during playback. If you  
like to repeat the entire program press  
[REPEAT] several times until “  
appears during playback.  
ALL”  
EN  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE SETTINGS  
DISPLAY  
ENTER  
AUDIO LANGUAGE  
SETUP  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
AUDIO SUBTITLE ANGLE  
The unit allows you to select a language during DVD  
disc (if multi languages are available) playback.  
MODE  
Shaded buttons are used for following operation.  
1 Press [AUDIO] during playback.  
1.ENG Dolby D 3/2.1ch 48k/3  
SUBTITLE LANGUAGE  
AUDIO  
2 Press [AUDIO] repeatedly to select your  
The unit allows you to select a language for subtitles  
during DVD disc (if available) playback.  
desired language.  
AUDIO  
NOTE  
1 Press [SUBTITLE] during playback.  
Pressing [AUDIO] may not work on some  
1.ENG/6  
DVDs with multiple audio languages (e.g.  
DVDs which allow audio language setting on  
the disc menu).  
SUBTITLE  
The subtitle language will appear on the display  
bar at the top of the TV screen.  
2 Press [SUBTITLE] repeatedly to select your  
desired subtitle language.  
STEREO SOUND MODE  
SUBTITLE  
3 To turn off subtitles, press [SUBTITLE]  
repeatedly until “OFF” appears.  
SUBTITLE  
1
Press [AUDIO] repeatedly during playback to  
select between “STEREO”, “L-ch” or “R-ch”.  
STEREO  
AUDIO  
NOTE  
Pressing [SUBTITLE] may not work on  
STEREO - both right and left channels are  
active (stereo)  
L-ch - only left channel is active  
R-ch - only right channel is active  
some DVDs with multiple subtitle languages.  
In this case, set it on the disc menu.  
(Operation varies between discs Refer to the  
manual of the disc.)  
If the desired language is not shown after  
pressing [SUBTITLE] several times, the disc  
does not have subtitles in that language.  
When “NOT AVAILABLE” appears on the TV  
screen, it means no subtitle is recorded on the  
scene.  
NOT AVAILABLE  
If you choose a language that has a 3 letter  
language code, the code will be displayed  
every time you change the Subtitle language  
setting. If you choose any other languages,  
“---” will be displayed instead. (Refer to page  
29.)  
EN  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAMERA ANGLE  
VIRTUAL SURROUND  
Some DVD discs contain scenes which have been shot You can enjoy surround-sound effect over two speak-  
simultaneously from various angles. You can change ers on this unit.  
the camera angle when the “  
screen.  
icon appears on the  
1 Press [MODE] repeatedly during playback  
then press [ENTER] to set it “1”, “2” or “OFF”.  
1 Press [ANGLE] during playback.  
OFF  
MODE  
ENTER  
repeatedly  
1 / 8  
ANGLE  
1: Natural effect  
The selected angle will be displayed on the dis-  
play bar at the top of the screen.  
2: Emphasized effect  
OFF: Original Sound  
If the “ANGLE ICON” setting is “OFF” in the  
2 Press [MODE] to exit.  
“OTHERS” menu, the “  
icon will not  
MODE  
appear. (Refer to page 31.)  
2 Press [ANGLE] repeatedly to select your  
You can also exit the menu by pressing  
[RETURN].  
desired angle.  
ANGLE  
NOTE  
For CD play only:  
Virtual Surround will not be effective if the  
sound mode is set to something other than  
STEREO. (Refer to “STEREO SOUND  
MODE” on pge 26.)  
BLACK LEVEL SETTING  
Adjust the Black Level Settings to make the black  
parts of the picture brighter.  
1 Press [MODE] during playback then press  
[ENTER] to switch “ON” or “OFF”.  
OFF  
MODE  
ON: Makes the dark parts brighter.  
OFF: Shows the original picture as recorded.  
(Initial setting)  
2 Press [MODE] twice or [RETURN] to exit.  
MODE twice OR  
RETURN  
NOTE  
The setting will be saved even if the unit is  
turned off.  
EN  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THE ON-SCREEN INFORMATION  
DISPLAY  
2 Press [DISPLAY] again to show current Total  
ENTER  
Track.  
SETUP  
TITLE  
RETURN  
ALL:  
Current track number / Total tracks  
4/12 0:13:45 - 0:45:40  
T
Shaded buttons are used for following operation.  
Current repeat setting appears only  
when the repeat setting is active  
T: Track repeat  
A: All Tracks repeat  
You can check the information about the current disc  
A
B: A-B repeat  
by pressing [DISPLAY].  
Remaining time of the entire disc  
Elapsed time of the entire disc  
For DVD-Vs  
3 Press [DISPLAY] again to exit.  
1 Press [DISPLAY] during playback to show  
current Chapter.  
Angle icon, appears only when avail-  
able on the DVD  
NOTE  
Current playback status  
11/16 0:00:00 - 0:03:30  
When you are playing a disc in PROGRAM  
or RANDOM mode, “ PROGRAM” (or  
RANDOM) will be displayed at step 2.  
Remaining time of the current chapter  
Elapsed time of the current chapter  
CH(Chapter):  
Current chapter number / Total chapters  
2
Press [DISPLAY] again to show current Title.  
For MP3  
1/3 0:00:00 - 1:23:45  
1 Press [DISPLAY] during playback.  
Remaining time of the current title  
Current playback status  
Elapsed time of the current title  
3
TRACK 01  
TT(Title):  
Current title number / Total titles  
The name of the file currently in play  
will be displayed.  
3 Press [DISPLAY] again.  
2 Press [DISPLAY] again.  
T
L1  
TR(Track):  
Layer numbers, appears only when  
playing a two-layered Disc  
L0: Layer 0 is playing  
Current track number / Total tracks  
1/36 0:01:15  
T
Current repeat setting, if active  
T: Track repeat  
L1: Layer 1 is playing  
G: Group (folder) repeat  
A: Disc repeat  
Current repeat setting appears only  
when the repeat setting is active  
C: Chapter repeat / T: Title repeat /  
Elapsed playing time of the current  
track  
A
B: A-B repeat  
BIT RATE: The amount of audio and  
video data currently being read  
3 Press [DISPLAY] again to show the current-  
playback mode.  
4 Press [DISPLAY] again to exit.  
(Only when you are playing a disc in PROGRAM or  
RANDOM mode.)  
PROGRAM  
RANDOM  
or  
4 Press [DISPLAY] again to exit.  
For Audio CDs  
1 Press [DISPLAY] during playback to show the  
current Track.  
Current playback status  
4/12 0:03:21 - 0:02:15  
T
Remaining time of the current track  
Elapsed time of the current track  
TR(Track):  
Current track number / Total tracks  
EN  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE DVD SET UP ITEMS  
D
LANGUAGE SETTING  
DISPLAY  
ENTER  
Follow steps to in the  
CUSTOM MENU  
.
SETUP  
TITLE  
RETURN  
1
2
3 Press [K] or [L] to select the desired item  
Shaded buttons are used for following operation.  
then press [ENTER].  
SETUP  
LANGUAGE  
CUSTOM MENU  
AUDIO  
SUBTITLE  
DISC MENU  
ORIGINAL  
OFF  
ENGLISH  
ENTER  
You can change the DVD player’s settings.  
AUDIO: Sets the audio language.  
SUBTITLE: Sets the subtitle language.  
DISC MENU: Sets the language for DVD menu.  
1 In stop mode, press [SETUP] twice, [L] to  
select “CUSTOM” then press [ENTER].  
SETUP  
4 Press [K] or [L] to select a setting then press  
twice  
[ENTER].  
SETUP  
SETUP  
AUDIO  
ORIGINAL  
ENGLISH  
FRENCH  
LANGUAGE  
LANGUAGE  
LANGUAGE  
QUICK  
CUSTOM  
INITIALIZE  
ENTER  
ENTER  
NOTE  
SETUP  
SUBTITLE  
OFF  
ENGLISH  
FRENCH  
If the menu does not appear, press [PLAY O]  
first, then press [STOP C]. Make sure the  
disc is in stop mode, then slowly press  
[SETUP] twice.  
SETUP  
DISC MENU  
ENGLISH  
FRENCH  
SPANISH  
2 Press [K] or [L] to select the desired item  
then press [ENTER] to confirm.  
If “OTHER” is selected on the “AUDIO”, “SUB-  
TITLE” or “DISC MENU” screen, press four-  
digit number to enter the code for the desired  
language.  
SETUP  
CUSTOM  
LANGUAGE  
DISPLAY  
AUDIO  
ENTER  
PARENTAL  
OTHERS  
Only the languages supported by the disc can be  
selected.  
Refer to the pages below to set up each item.  
LANGUAGE: See LANGUAGE SETTING  
5 Press [SETUP] to exit the menu.  
D
SETUP  
DISPLAY:  
See E DISPLAY SETTING  
F
AUDIO:  
See  
AUDIO SETTINGS  
PARENTAL: See G PARENTAL CONTROL  
NOTE  
H
OTHERS:  
See  
OTHER SETTINGS  
Language Setting for Audio and Subtitle are  
not valid for some discs due to default setting  
of the disc. In this case, set them by pressing  
[AUDIO] and [SUBTITLE]. (Refer to page  
26.)  
If you select a language that is not supported  
by the disc, subtitle will automatically be set  
OFF and the first item of the audio languages  
will be automatically set.  
EN  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E
F
DISPLAY SETTING  
AUDIO SETTINGS  
Choose the appropriate Audio settings for your equip-  
ment as it only affects during the playback of DVD  
discs.  
Follow steps to in the on  
CUSTOM MENU  
page 29.  
1
2
3 Press [K] or [L] to select the below items then  
Follow steps to in the on  
CUSTOM MENU  
1
2
press [ENTER].  
page 29.  
SETUP  
DISPLAY  
3 Press [K] or [L] to select the below items then  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
ENTER  
press [ENTER].  
SETUP  
AUDIO  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
ON  
BITSTREAM  
ENTER  
TV MODE:  
QUICK  
You can change certain aspects of the DVD display  
screens and on-screen messages on the TV screen.  
DRC (Dynamic Range Control):  
SETUP  
AUDIO  
SETUP  
DISPLAY  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
ON  
BITSTREAM  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
To compress the range of soft to loud sound.  
The default setting is “ON”.  
4:3 LETTER BOX (default): To show black bars  
on top and bottom of the screen.  
4:3 PAN & SCAN: To show a full height picture  
with both sides trimmed.  
DOWN SAMPLING:  
SETUP  
AUDIO  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
ON  
BITSTREAM  
STILL MODE  
This function allows you to adjust picture resolu-  
tion and quality in the still mode.  
:
ON : Output in 48 kHz. (default)  
OFF : Output the original sound.  
When playing disc with copyright Protection  
If you select “OFF”, copyright protection will be  
activated and sound will be down sampled at  
48kHz.  
SETUP  
DISPLAY  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
AUTO (default): Automatically select the best  
resolution setting (FRAME or FIELD) based on  
the data characteristics of the pictures.  
FIELD: Select “FIELD” when the pictures are  
still unstable even if “AUTO” is selected.  
FIELD stabilizes the pictures, although the pic-  
ture quality may become coarse due to the limit-  
ed amount of data.  
FRAME: Select “FRAME” to display relatively  
motionless pictures in higher resolution.  
FRAME improves the picture quality, although it  
may unstabilizethe pictures due to simultaneous  
output of two field data.  
DOLBY DIGITAL:  
Set to “BITSTREAM” when the unit is connected  
QUICK  
to a Dolby Digital Decoder.  
SETUP  
AUDIO  
DRC  
ON  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
BITSTREAM  
BITSTREAM: Output a Dolby Digital signal  
(default)  
PCM: Convert the Dolby Digital to PCM  
(2 channel stereo)  
4 Press [SETUP] to exit the menu.  
SETUP  
4 Press [SETUP] to exit the menu.  
SETUP  
QUICK MENU  
You can select the “TV MODE” or “DOLBY DIGITALfrom the QUICK menu quickly. To access the  
QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 29.  
1
TV SET UP MENU IN DVD MODE  
You can access the TV SETUP menu by pressing [SETUP] from the DVD mode, and select only  
“LANGUAGE” and “BACK LIGHT”.  
EN  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL LEVELS  
G
PARENTAL CONTROL  
ALL  
Parental Control limits the disc viewing that exceed  
your setting (with a password or playback will stop).  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
All parental lock is cancelled.  
Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
Levels 7 to 2  
Only DVD software intended for general use and  
children can be played back.  
PARENTAL LEVEL  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
Level 1  
Only DVD software intended for children can be  
played back, with those intended for adult and gen-  
eral use prohibited.  
Follow steps to in the  
CUSTOM MENU  
on  
1
2
page 29.  
3 Enter your four-digit password then press  
H
OTHER SETTINGS  
[ENTER].  
Follow steps to in the on  
CUSTOM MENU  
1
4
7
2
5
8
3
6
9
1
2
SETUP  
PARENTAL  
PASSWORD  
Enter current password.  
page 29.  
ENTER  
3 Press [K] or [L] to select the below items then  
0
press [ENTER].  
Press [4], [7], [3], [7] then enter your password  
if you forget the password.  
SETUP  
OTHERS  
ANGLE ICON  
SCREEN SAVER  
ON  
OFF  
ENTER  
4 Press [K] or [L] to select “PARENTAL LEVEL”  
then press [ENTER].  
ANGLE ICON:  
SETUP  
PARENTAL  
Press [ENTER] repeatedly to turn Angle icon  
“ON” or “OFF”.  
PARENTAL LEVEL  
PASSWORD CHANGE  
ALL  
ENTER  
The default setting is “ON”.  
SCREEN SAVER:  
5 Press [K] or [L] to select the desired level  
Press [ENTER] repeatedly to turn Screen Saver  
“ON” or “OFF”.  
then press [ENTER].  
SETUP  
PARENTAL  
The default setting is “OFF”. If you select “ON”,  
the screen saver program starts when there is no  
input from the unit for 5 minutes in stop mode.  
PARENTAL LEVEL  
ALL  
ENTER  
8
7 [NC-17]  
6 [R]  
4 Press [SETUP] to exit the menu.  
6 Press [SETUP] to exit the menu.  
SETUP  
SETUP  
NOTE  
When doing this for the first time, enter any 4  
digits. (except for 4737) That number will be  
used as the password. (in the event you forget  
the password, see below)  
To change the password, press [K] or [L] to  
select PASSWORD CHANGE” at step 4  
then press [ENTER]. Enter the four-digit  
password, then press [ENTER].  
With some DVDs, it may be difficult to find  
if they are compatible with parental lock. Be  
sure to check if the parental lock function  
operates in the way that you have set.  
Record the password in case you forget it.  
EN  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISPLAY  
SETUP  
ENTER  
TITLE  
RETURN  
Shaded buttons are used for following operation.  
INITIALIZE  
This allows you to return all selections of SETUP  
(except for PARENTALand menu language) to  
their default settings.  
1 Press [SETUP] twice in stop mode so that the  
“INITIALIZE” menu appears.  
SETUP  
2 Press [K] or [L] to select “INITIALIZE” then  
press [ENTER].  
SETUP  
QUICK  
CUSTOM  
ENTER  
INITIALIZE  
3 Press [K] or [L] to select “YES” then press  
[ENTER] twice.  
SETUP  
INITIALIZE  
Initialize?  
NO  
YES  
ENTER  
twice  
All the settings (except for “PARENTALand  
menu language) will be cleared.  
To cancel the initialization, select “NO”.  
4 Press [SETUP] to exit the menu.  
SETUP  
EN  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING GUIDE  
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-  
sulting the following checklist.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Aim the remote control directly at the sensor on the front of the unit.  
Reduce the distance to the unit. You have to be within 23 feet.  
Replace the batteries in the remote control.  
Re-insert the batteries with their polarities (+/- signs) as indicated.  
Tune your radio to an empty AM station so that you hear a lot of  
noises. Then, turn the volume up. If you hear some signal sound from  
the radio when pressing buttons on the remote control, the remote con-  
trol is working.  
No power  
The unit does not respond to the  
remote control  
Check if the correct mode is selected. If not switch the mode by  
pressing [SELECT], whichever you need.  
TV Mode  
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked  
possibilities. Before arranging for service, check these items. It could save your time and money.  
PROBLEM  
No picture or sound  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Press [SELECT] to select TV mode.  
Then try other TV feature.  
Let the unit program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Check for broken pin of the antenna cable.  
Adjust volume control on remote control or main unit.  
Press [MUTE] to restore sound.  
No picture or poor picture on the  
unit  
No sound or poor sound  
Bars On Screen  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Picture Distorted or Blurred  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust “COLOR” control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust “CONTRAST” & “BRIGHT” control.  
Picture Rolls Vertically  
Lines or Streaks in Picture  
No Color  
Poor Reception on Some Channels  
Ghosts in Picture  
Weak Picture  
EN  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROBLEM  
Sound OK, Picture Poor  
CORRECTIVE ACTION  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Adjust “CONTRAST” & “BRIGHT” control.  
Try a new channel, if OK, then possible station trouble.  
Check for local interference.  
Picture OK, Sound Poor  
No operation by infrared Remote  
Control  
Different color marks on screen  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the unit away from the appliances,  
the unit can repair itself automatically. If you want to repair immedi-  
ately, unplug the power cord, then plug it in again 30 minutes later or  
so. This automatically resets the unit.  
CLOSED CAPTION PROBLEM  
POSSIBLE REMEDY  
Misspelling in captions  
Error committed by the closed captioning production company.  
Possible in a live broadcast. Not in case of a prerecorded program.  
Text is not shown in its entirety or  
a delay occurs from what is being  
said.  
A few seconds of delay is common for live broadcast.  
Display capacity may not exceed 220 words per minute. If a dialogue  
exceeds that rate, selective editing is used to insure that the captions  
remain up-to-date with the current TV screen dialogue.  
Captions scrambled with white  
boxes  
Caused by interferences of building, power lines, thunderstorms, etc.  
No captions in a program which  
must contain closed caption  
The broadcast may use a time compression process to speed up the  
program. The decoder cannot read the compressed information and  
captions will be lost.  
Black box in the TV screen  
You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or  
Caption “OFF”.  
EN  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD Mode  
PROBLEM  
CORRECTIVE ACTION  
Insert a correct video disc that plays on this unit.  
Press [SELECT] to select DVD mode, then try other DVD feature.  
Insert the disc.  
No picture  
Disc cannot be played  
Clean the disc.  
Place the disc correctly, with the label side up.  
Cancel the parental lock or change the control level.  
Connect the audio cables firmly.  
Turn the power of the audio component on.  
Correct the audio output settings.  
Correct the input settings on the audio component.  
This unit does not support DTS audio. This is not a malfunction.  
There are some cases where pictures may be slightly distorted,  
which are not a sign of a malfunction.  
No sound  
No DTS audio is output  
Distorted picture  
Although pictures may stop for a moment, this is not a malfunction.  
The selected language is not available for audio or subtitles on the  
DVD. (This is not a malfunction.)  
Audio or subtitle language  
does not match the set up  
The camera angle cannot be changed The DVD does not contain sequences recorded from different cam-  
era angles. (This is not a malfunction.)  
Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected  
changed  
language. (This is not a malfunction.)  
“Prohibited icon” appears on the  
screen, prohibiting an operation  
CD sound dropout  
That operation is prohibited by the unit or the disc.  
(This is not a malfunction.)  
Scratched disc. Replace the disc with an unscratched one.  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
DVD picture in mosaic  
No DVD reproduction  
Disc cannot be inserted  
Disc cannot be taken out  
Check if any disc is already in.  
Unplug and plug again the power cord to the outlet, and then press  
[EJECT A] on the remote control.  
Press and hold [EJECT A] on the unit for more than 5 seconds.  
NOTE  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owner’s Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
EN  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CABINET CLEANING  
DISC HANDLING  
Wipe the front panel and other exterior surfaces of  
the unit with a soft cloth immersed in lukewarm  
water and wrung dry.  
Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the unit. Such chemicals may  
cause damage and discoloration to the exposed sur-  
faces.  
SERVICING  
Always store the disc in its protective case when it  
is not used.  
Should your unit become inoperative, do not try to  
correct the problem by yourself. There are no user-  
serviceable parts inside. Turn off, unplug the power  
cord and please call our help line mentioned on  
the front page, to locate an Authorized Service  
Center.  
IF THE LASER OPTICAL PICKUP UNIT  
IS DIRTY  
To clean-off, use a soft cloth.  
If the unit still does not perform properly when it is  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
operated, while referring to the relevant sections  
and to “TROUBLESHOOTING GUIDE” in this  
Owner’s Manual, the laser optical pickup unit may  
be dirty. Consult your dealer or an Authorized  
Service Center for inspection and cleaning of the  
laser optical pickup unit.  
Do not use detergent or abrasive cleaning agents.  
EN  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV  
LCD :  
Television system :  
Closed caption system :§15.119/FCC  
Channel coverage:  
15 inch  
NTSC-M  
OTHER SPECIFICATIONS  
Terminals  
Antenna input:  
VHF/UHF/CATV  
75 ohm unbalanced (F-type)  
Mini DIN 4-pin jack  
RCA connector [ 1  
VHF:  
UHF:  
CATV:  
2 ~ 13  
14 ~ 69  
S-Video input:  
Video input:  
Audio L/R input:  
2 ~13, A ~ W,  
W+1 ~ W+84,  
A-5 ~ A-1, 5A  
181 channel  
frequency synthesized  
tuning system  
Direct access keyboard,  
programmable  
scan and up/down  
RCA connector [ 4  
Component video input:  
One pin jack (Y), 1Vpp (75 ohm)  
Two pin jacks (Pr)/(Pb), 700mVpp (75 ohm)  
Coaxial digital audio output:  
Tuning System:  
Channel access:  
One pin jack, 500mmVpp (75 ohm)  
Headphone:  
Remote control:  
1/8" stereo (3,5mm)  
Digital encoded  
infrared light system  
Operating  
temperature:  
5°C to 40°C  
DVD  
(41°F~104°F)  
Product type:  
Discs:  
DVD Player  
DVD video, Audio CD  
CD with MP3 files  
Power requirements: AC 120V, 60Hz  
Power consumption  
(Maximum):  
LCD:  
47W  
15"  
Dimensions:  
H : 14"  
(355mm)  
W: 20-5/8" (524mm)  
D : 8-7/16" (215mm)  
9.7 lbs. (4.4kg)  
Weight:  
Designs and specifications are subject to change without notice.  
If there is a discrepancy between languages, the default language will be English.  
EN  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDICE  
INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 38  
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 39  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 40  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 40  
CONEXIÓN EXTERNA . . . . . . . . . . . . . . . . . . . . . . . . . 41  
SECCIÓN DE DVD  
REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . 44  
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 44  
MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
SECCIÓN DE TV  
OPERACIÓN DE TV Y AJUSTES. . . . . . . . . . . . . . . . . 42  
PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 42  
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
IDIOMA DE MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
CONTROLES DE OPERACIÓN Y FUNCIONES  
NOTE  
Para elegir el modo de DVD presione primero [SELECT], [PLAY O] o [EJECT A], o introduzca un  
disco en la ranura. De otra manera, el DVD no funcionará.  
- MANDO A DISTANCIA  
• Para saber cómo funciona el mando a distancia, consulte la [Fig.1] de la página 8.  
1.Botón POWER  
11. Botón CLEAR  
Presione para encender y apagar la unidad.  
Presione para cancelar o borrar un ajuste intro-  
ducido actualmente.  
2.Botón PICTURE  
Presione para ajustar la imagen.  
3.Botones numéricos  
Presione para seleccionar directamente el número  
de canal deseado .  
Botón +100 (para modo TV)  
Presione para seleccionar canales cuyo número  
sea superior a 99.  
Botón +10 (para modo DVD)  
Presione para introducir los números superiores a  
9 deseados.  
Presione para borrar la pantalla “DISCO ADEN-  
TRO”.  
12. Botón MODE  
Presione para visualizar la pantalla de la repro-  
ducción programada o la de reproducción aleato-  
ria en el modo de parada.  
Presione para visualizar la pantalla de ajuste del  
nivel del negro o la pantalla de sonido envolvente  
durante la reproducción.  
13. Botón SEARCH MODE  
Presione para localizar un punto deseado.  
4.Botón SLEEP  
Presione para ajustar el temporizador de reposo  
14. Botón AUDIO  
Para modo TV: Presione para seleccionar el  
modo de sonido de TV (ESTEREO/SAP/MONO).  
Para modo DVD: Presione para seleccionar un  
idioma de audio deseado (si está disponible).  
5.Botones SKIP H /  
G
Presione una vez para omitir capítulos o pistas y  
desplazarse a un punto específico.  
6.Botón PLAY  
O
15. Botón EJECT  
A
Presione para reproducir el disco.  
Presione para extraer un disco de la unidad.  
7.Botón PAUSE  
F
16. Botón SELECT  
Presione para hacer una pausa en la reproducción  
del disco actual.  
Presione para seleccionar el modo TV, modo de  
entrada externa o modo de DVD.  
8.Botón DISPLAY  
Para modo TV  
17. Botones CH.  
K
/
L
:
Presione para seleccionar canales memorizados.  
Presione para visualizar el número actual de canal en  
la pantalla del televisor.  
18. Botones VOL. X /Y  
Para modo DVD  
:
Presione para controlar el nivel de volumen del  
DVD y el televisor.  
Presione para visualizar el estado actual en la pan-  
talla del televisor.  
19. Botón MUTE  
9.Botón SETUP  
Presione para entrar o salir del menú de configu-  
ración del TV/DVD.  
Presione para silenciar el sonido. Presiónelo de  
nuevo para restablecer el sonido.  
20. Botón ZOOM  
10. Botón TITLE  
Presione para ampliar la parte de la imagen repro-  
ducida en un DVD.  
Presione para visualizar el menú de títulos.  
- 38 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26. Botón RETURN  
21. Botón REV  
E
Presione para volver a la pantalla anterior en el  
menú de configuración.  
Presione para ver la imagen en DVD en retroceso  
o en cámara lenta de retroceso.  
27. Botón A-B  
Botón FWD  
Presione para mover en avance rápido o en  
cámara lenta en el disco.  
D
Presione para repetir la reproducción de una sec-  
ción seleccionada.  
28. Botón ANGLE  
22. Botón STOP  
C
Presione para cambiar el ángulo de la cámara y  
ver la secuencia que se está reproduciendo desde  
un ángulo diferente (si existe).  
Presione para detener la reproducción del disco.  
23. Botón DISC MENU  
Muestra el menú del DVD.  
29. Botón REPEAT  
– Muestra la lista de archivos del disco MP3.  
Repite la reproducción del disco, título, capítulo,  
grupo o pista actual.  
24. Botón ENTER  
Presione para establecer un ajuste.  
30. Botón SUBTITLE  
25. Botones  
K
(Arriba) /  
L
(Abajo) /{ (Izquierda) /  
Presione para seleccionar el idioma de los subtí-  
tulos.  
B
(Derecha)  
Presione para seleccionar o ajustar los ítems del  
menú.  
- PANEL FRONTAL  
• Para ver la ilustración del panel frontal, vaya a la página 9, [Fig. 2].  
31. Botón MENU  
36. Botones CHANNEL X /Y  
Presione para entrar o salir del menú de configu-  
ración del TV/DVD.  
Presione para seleccionar canales memorizados.  
37. Botón SELECT  
32. Botón STOP  
Presione para detener la reproducción del disco.  
33. Botón PLAY  
Presione para reproducir el disco.  
P
Presione para seleccionar el modo TV, modo de  
entrada externa o modo de DVD.  
B
38. Botón POWER  
Presione para encender y apagar la unidad.  
34. Botón EJECT  
A
39. Ventana de sensor remoto  
Presione para extraer un disco de la unidad.  
35. Botones VOLUME X /Y  
Presione para controlar el nivel de volumen del  
DVD y el televisor.  
PARA INSERTAR LAS PILAS  
PRECAUCIONES A LA HORA DE  
INSERTAR LAS PILAS  
1 Abra la cubierta del compartimiento de las pilas  
empujando la cubierta del mando a distancia en el  
sentido de la flecha.  
Asegúrese de seguir la polaridad correcta, tal como  
se indica en el compartimiento de las pilas. Si se  
colocan las pilas con la polaridad invertida se  
pueden ocasionar daños a la unidad.  
2 Inserte 2 pilas “AA” en el compartimiento de las  
pilas, en el sentido indicado por las marcas de  
polaridad (+/-).  
No mezcle distintos tipos de pilas (ej. alcalina y de  
carbón-zinc) o pilas viejas con nuevas.  
3 Vuelva a poner la cubierta.  
Si no va a usarse la unidad durante un período  
largo de tiempo, quite las pilas para prevenir daños  
o lesiones ocasionadas por posibles fugas de las  
pilas.  
No intente recargar las pilas que no sean para  
recargar; pueden sobrecalentarse y estropearse.  
NOTA  
No se recomienda el uso de mandos a distancia universales. No todas las funciones pueden controlarse  
con un mando a distancia universal.  
Si decide usar un mando a distancia universal con esta unidad, sea consciente de que el número de código  
suministrado puede no adecuarse a la unidad. En este caso, llame al fabricante del mando a distancia uni-  
versal.  
- 39 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARACIÓN PARA LA UTILIZACIÓN  
CONEXIONES DE ANTENA/CABLE  
NOTA  
Los cables utilizados aquí están disponibles en los comercios.  
Para su seguridad y para evitar daños a la unidad, desconecte el cable de antena de la toma ANT  
antes de trasladar la unidad.  
- CONEXIONES DE ANTENA/CABLE (CON O SIN CAJA)  
[Parte posterior de este unidad]  
Señal del  
TV cable  
Antena  
o
L
UT  
O
ITA  
DIG  
O
DI  
AU  
L)  
XIA  
OA  
(C  
O
2
E
V
I
D
A
R
D
I
O
U
L
T
N
E
N
P
O
C
O
M
Y
Pb  
Pr  
Cable de entrada de la antena del hogar  
/ empresa de cable (sin caja de cable)  
R
D
I
O
A
U
L
1
O
E
I
D
S
V
O
E
I
D
V
-
V
I
D
E
O
T
N
N
Caja de Cable o  
Caja de Satélite *  
A
O
H
E
A
D
P
H
O
E
OUT  
IN  
(SALIDA)  
(ENTRADA)  
ANT  
Cable de entrada de la empresa de cable  
o antena de satélite  
*Algunos sistemas de TV por cable utilizan señales codifi-  
cadas y requieren un convertidor especial para recibir  
estos canales. Consulte con su empresa de cable local.  
SI TIENE UNA TOMA DE PARED  
Conecte el televisor a la toma de antena de pared con  
el cable RF (disponible en los comercios).  
CUANDO SE USA UNA CAJA DE CON-  
VERTIDOR/CAJA DE SATÉLITE  
Si su compañía de televisión por cable le suministra  
una caja de convertidor o si usa un sistema de  
satélite, podrá utilizar la conexión básica que se  
muestra anteriormente.  
SI TIENE CABLE DE HILOS  
Conecte el televisor al cable de antena.  
La selección de los canales deberá hacerse con la  
caja de convertidor o caja de satélite. Esto significa  
que no es posible cambiar de canal utilizando el  
mando a distancia de la unidad.  
NOTA  
Patilla torcida  
Antes de conectar la antena en la toma ANT de la unidad, compruebe que la patil-  
la no esté torcida. Si lo está, ponga la patilla recta tal como se muestra en la ilus-  
tración y a continuación conecte la patilla a la toma ANT de la unidad.  
Cable  
Conector  
(Debe ponerse recta) (patilla recta)  
Para el instalador de sistemas CATV:  
Esta nota tiene la finalidad de llamar la atención del instalador de sistemas CATV para que tenga en cuenta el  
Artículo 820-40 de la NEC, que proporciona recomendaciones para hacer una conexión a tierra apropiada y, en par-  
ticular, especifica que la tierra del cable debe conectarse al sistema de puesta a tierra del edificio, tan cerca del punto  
de entrada del cable como sea posible.  
- 40 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONEXIÓN EXTERNA  
Puede conectar esta unidad a su equipo de audio/vídeo.  
[Parte posterior  
de este unidad]  
Asegúrese de apagar todos los componentes del  
sistema antes de conectar otro componente.  
Consulte los manuales de instrucciones de los  
componentes que va a conectar a la unidad.  
NOTA  
L
A
IT  
IG  
D
T
U
AUDIO  
O
IO  
D
U
A
L)  
IA  
X
A
O
(C  
2
O
E
I
D
V
R
I
O
D
U
A
L
T
N
E
N
O
Y
VIDEO2  
M
P
O
C
b
P
r
P
Cuando utilice las tomas de entrada externa, seleccione  
AUX1” o “AUX2” presionando [SELECT].  
(Consulte la página 42.)  
R
D
I
O
E
A
U
L
VIDEO1  
O
V
I
D
E
S
O
1
D
I
V
O
E
I
D
-
V
A
N
T
Para utilizar la tomas VIDEO1, seleccione  
AUX1”.  
E
N
O
H
P
D
A
E
H
Para utilizar la tomas VIDEO1, seleccione  
AUX2”.  
Use esta conexión si su propio equipo A/V (ej.  
videograbadora) tiene tomas de salida de audio y  
vídeo. Cuando se usa un cable Vídeo-S, se obtiene  
una imagen mejor.  
- ENTRADA DE VÍDEO1  
(ENTRADA)  
(SALIDA)  
ej.  
Cable de audio  
R
AUDIO  
L
Cable de vídeo  
O
VIDEO1  
EO  
VID  
Videograbadora  
S-VIDEO  
Cable VIDEO-S  
NOTA  
Si su propio equipo es monofónico (sólo tiene una toma de audio), conecte el cable de audio a la toma AUDIO L de esta unidad.  
Si conecta la toma VIDEO y la toma S-VIDEO simultáneamente, se da prioridad a la S-VIDEO. .  
Use esta conexión si el equipo A/V (ej. videocámara  
o videojuego) tiene tomas de salida de vídeo COM-  
PONENTE (Y,Pb,Pr). Podrá disfrutar de una mejor  
imagen con esta conexión.  
ej.  
- ENTRADA DE VÍDEO2  
VIDEO2  
Cable de audio  
R
AUDIO  
L
(SALIDA)  
(ENTRADA)  
Videocámara  
COMPONENT  
Y
Cable de vídeo  
componente  
Pb  
Pr  
(SALIDA)  
(ENTRADA)  
Videojuego  
Podrá disfrutar de un sonido de DVD con  
más presencia desconectando el equipo de  
audio digital, tal como el descodificador  
Dolby Digital.  
- SALIDA DE AUDIO  
A toma de ENTRADA  
DIGITAL COAXIAL DE AUDIO  
Equipo doméstico de audio  
Descodificador Dolby Digital  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
(SALIDA)  
NOTA  
La fuente de audio de un disco en un formato de sonido envolvente Dolby Digital de 5,1 canales no se  
puede grabar como sonido digital mediante una pletina MD o DAT.  
Si conecta un descodificador Dolby Digital, ajuste la función “DOLBY DIGITAL” a “BITSTREAM”  
para salida de audio en el modo de configuración.  
A menos que se haga la conexión a un decodificador “DOLBY DIGITAL” a “PCM” para salida de audio  
en el modo de configuración.  
La reproducción en una unidad utilizando ajustes incorrectos puede generar ruido y distorsión, y también  
puede provocar daños a los altavoces.  
Fabricado bajo licencia de Dolby Laboratories. “Dolby” y el símbolo de la doble D son marcas comerciales de  
Dolby Laboratories.  
- 41 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECCIÓN DE TV  
OPERACIÓN DE TV Y AJUSTES  
NOTA  
Para seleccionar el número de canal medi-  
ante los botones numéricos:  
POWER PICTURE SELECT  
EJECT  
CH.  
Para seleccionar un número de canal de un  
solo dígito, presione primero [0] (ej. Para el  
1
4
2
5
8
0
3
6
canal 2, presione [0] [2]).  
Para seleccionar canales por cable cuyos números  
sean superiores a 99, presione primero[+100/+10].  
(ej. Para el canal 125, presione [+100/+10] [2] [5]).  
7
SLEEP  
9
+100  
VOL.  
+10  
X
Y
] para seleccionar el  
4 Presione [VOL.  
/
SKIP  
ZOOM  
MUTE  
nivel de volumen deseado.  
PLAY  
STOP  
REV  
FWD  
VOL.  
DISC  
VOLUMEN 20  
PAUSE SLOW  
DISPLAY  
MENU  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Presione [MUTE] para silenciar el sonido al instante.  
Vuelva a presionarlo para restaurar el nivel de  
volumen anterior.  
ENTER  
SETUP  
TITLE  
RETURN  
NOTA  
Si presiona [CH.  
puede cambiar los canales del televisor. Incluso  
si apaga la unidad en el modo DVD, cuando  
vuelve a encenderlo se pondrá en el modo TV.  
Los botones sombreados se utilizan para las siguientes operaciones.  
K
/
L] en el modo DVD,  
PARA MIRAR UN PROGRAMA DE TV  
1 Conecte el cable de alimentación de  
la unidad a una toma estándar CA.  
PARA VER UN CANAL POR CABLE O  
SATÉLITE  
Si la unidad está conectada a una caja de convertidor  
NOTA  
Si se visualiza algún dígito en la esquina de la  
o caja de satélite, presione [CH.  
K
/
L] para selec-  
pantalla, presione [POWER] sin desconectar  
cionar CH3 o CH4 según el ajuste de canal de salida  
del aparato, y seleccione en él el canal deseado.  
el cable de alimentación.  
2 Presione [POWER] para encender la unidad.  
PARA VER SEÑALES DE ENTRADA DE  
UN DISPOSITIVO EXTERNO  
POWER  
Cuando conecte un equipo externo a las tomas de  
entrada delanteras AUDIO/VIDEO, presione  
3 Presione [CH.  
K
/
L] para seleccionar el  
[SELECT] o [CH.  
K
/
L] repetidamente hasta que  
número de canal deseado.  
aparezca en la pantalla “AUX1” o “AUX2”.  
CH.  
NOTA  
Si hay un disco dentro de la unidad, se visu-  
alizará el mensaje “DISCO ADENTRO” en la  
O
pantalla durante 10 segundos.  
Presione los botones numéricos para intro-  
ducir el número de canal deseado.  
1
4
7
2
5
8
3
6
9
DISCO ADENTRO  
+100  
0
+10  
Para borrar el mensaje al instante, presione [CLEAR].  
- 42 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AJUSTE DE CANAL  
IDIOMA DE MENÚ  
PROGRAMACIÓN AUTOMÁTICA DE CANAL  
1 Presione [SETUP] y a continuación presione  
[K  
] o [  
L
] para seleccionar el “LANGUAGE”.  
De acuerdo con la configuración de fábrica, esta  
unidad ha memorizado todos los canales, incluidos  
los que no están disponibles en su localidad. Esta  
función solo pone automáticamente en memoria los  
canales disponibles.  
- TV SET UP -  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
BACK LIGHT [BRIGHT]  
B
ENTER  
1 Presione [SETUP] y a continuación presione  
2 Presione [ENTER] repetidamente para selec-  
cionar “ENGLISH” = inglés, “ESPAÑOL” o  
“FRANÇAIS”= francés.  
[K  
] o [  
L
] para señalar “AJUSTE DE CANAL.  
- TV PREP. -  
B
AJUSTE DE CANAL  
AJUSTE DE V-CHIP  
SETUP  
IDIOMA  
TITULO  
[ESPAÑOL]  
[OFF]  
ENTER  
LUZ DE FONDO [BRILLO]  
3 Presione [SETUP] para salir del menú.  
SETUP  
2 Presione [ENTER] y a continuación presione  
[K  
] o [  
L
] para señalar “PREA. AUTO CA..  
– AJUSTE DE CANAL –  
NOTA  
AGREGAR/BORRAR CA (CATV)  
Esta función selecciona sólo el idioma del  
menú de pantalla; no la fuente de audio.  
B
PREA. AUTO CA.  
ENTER  
Si por alguna razón el menú está en español o  
en francés, presione [SETUP], luego [K] o  
[L] para seleccionar “IDIOMA [ESPAÑOL]”  
o “LANGAGE [FRANÇAIS]”, y a contin-  
uación presione [ENTER] repetidamente para  
seleccionar el idioma deseado y luego presione  
[SETUP].  
3 Presione [ENTER].  
ENTER  
El sintonizador explora y memoriza todos los  
canales activos de su localidad.  
El sintonizador se detiene en el canal memorizado  
inferior.  
NOTA  
Cuando está activado “PREA. AUTO CA.”  
donde no hay entrada de señal de TV, apare-  
cerá “NO HAY SEÑAL DE TV” en la pan-  
talla después de completarse la exploración  
de los canales.  
La unidad puede reconocer canales CATV como  
canales de TV si las condiciones de recepción  
son malas. En este caso, compruebe la conexión  
de la antena y vuelva a intentar “PREA. AUTO  
CA.” cuando las condiciones de recepción  
mejoren.  
La programación de canales memorizados  
NO es necesaria cuando la unidad está conec-  
tada a una caja de convertidor o caja de  
satélite. Sólo tiene que seleccionar el canal  
para caja de convertidor o entrada de satélite  
(ej. CH3) de la unidad y a continuación selec-  
cione el canal que desee en la caja de conver-  
tidor o la caja de satélite.  
- 43 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECCIÓN DE DVD  
REPRODUCCIÓN DE UN DISCO  
POWER PICTURE SELECT  
EJECT  
5 Precione [EJECT A] para extraer la disco de  
la unidad.  
EJECT  
3
SKIP  
ZOOM  
MUTE  
NOTA  
Cuando el modo DVD se ha cambiado al modo  
TV, el modo DVD se desactiva primero y a  
continuación aparece la imagen y suena el  
sonido en el TV al cabo de unos 4 segundos.  
De la misma manera, cuando se presiona  
[POWER] para apagar la unidad en el modo  
DVD, este modo se desactiva primero y a con-  
tinuación se apaga la unidad.  
PLAY  
STOP  
REV  
FWD  
DISC  
MENU  
PAUSE SLOW  
DISPLAY  
ENTER  
SETUP  
TITLE  
RETURN  
Puede aparecer “  
” en la parte superior  
derecha de la pantalla del TV durante su fun-  
cionamiento, que avisa de que el DVD o el  
disco han encontrado una operación prohibida.  
Con los DVD que utilizan títulos para señales  
de reproducción programada, la reproducción  
puede empezar desde el segundo título y  
puede omitir estos títulos.  
Durante la reproducción de un disco de dos  
capas, las imágenes pueden detenerse durante  
un rato. Esto ocurre cuando la 1ª capa cambia  
a la 2ª. No se trata de una anomalía.  
Los botones sombreados se utilizan para las sigu-  
ientes operaciones.  
REPRODUCCIÓN BÁSICA  
PARA EMPEZAR  
Si es necesario, encienda el amplificador y cualquier  
otro componente.  
REPRODUCCIÓN DE MP3  
1 Presione [POWER] para encender la unidad.  
POWER  
1
En el modo de parada, presione [DISC MENU] y precione  
K
L
[
] o [ ] para seleccionar el grupo o pista que desee.  
2 Abra la bandeja del disco manualmente.  
LISTA DE ARCHIVOS  
NOMBRE DE DISCO  
DISC  
MENU  
Nombre de carpeta 1  
Nombre de carpeta 2  
Nombre de carpeta 3  
Nombre de carpeta 4  
Nombre de archivo 1  
Nombre de archivo 2  
Nombre de archivo 3  
ER  
POW  
CT  
SELE  
NEL  
CHAN  
V
OLU  
ME  
K
EJECT  
L
PLA  
Y
K
STOP  
L
MENU  
A
B
C
Nombre de carpeta 1  
3
4
Introduzca el disco elegido con la etiqueta hacia la parte trasera de la  
unidad para reproducirlo. Al presionar suavemente el disco para intro-  
ducirlo en la ranura, su reproducción empezará automáticamente.  
Si ha selecciona un grupo, presione [B] o  
[ENTER] para ir a la pantalla de selección de  
pistas. Presione [s] para volver a la pantalla  
anterior (excepto la página superior).  
Si ha seleccionado una pista, presione [ENTER]  
para empezar a reproducir pistas. Si empieza por  
la que acaba de elegir se reproducirán las pistas  
siguientes.  
Si no puede visualizarse enseguida en pantalla la  
lista entera de archivos, aparece la “n”para ir a la  
página siguiente. appears to go to the next page.  
Presione [TITLE] para volver al archivo superior  
de la jerarquía más alta del programa y de la  
lista de archivos.  
ER  
POW  
CT  
SELE  
NEL  
CHAN  
V
OLU  
ME  
K
EJECT  
L
PLA  
Y
K
STOP  
L
MENU  
A
B
C
La reproducción empezará desde el primer capí-  
tulo/pista del disco.  
Si la reproducción no empieza automáticamente,  
presione [PLAY O].  
Presione [STOP C] para detener la reproducción.  
C
2
Presione [STOP ] para detener la reproducción.  
STOP  
STOP  
- 44 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTA  
REANUDACIÓN  
Las carpetas se conocen como grupos; los  
archivos, como pistas.  
3
Los archivos MP3 van acompañados de  
iconos.  
1 Durante la reproducción, presione [STOP C].  
Se puede reconocer un máximo de 255 carpetas.  
Se puede reconocer un máximo de 999 archivos.  
Pueden crearse hasta 8 jerarquías.  
REANUDACIÓN ACTIVADA  
Se recomienda para esta unidad el uso de  
archivos grabados según las especificaciones  
siguientes:  
STOP  
Presione 'PLAY' para reproducir  
desde aquí.  
Para reproducir desde el inicio,  
primero presione 'STOP' y luego 'PLAY'.  
Frecuencia de muestreo: 44,1 kHz o 48kHz  
Velocidad de transmisión de bits constante:  
32kbps ~ 320kbps  
(Ejemplo: DVD o CD audio)  
Para archivos MP3 grabados en velocidad de  
Aparecerá el mensaje de reanudación en la pan-  
talla del TV.  
transmisión de bits variable (VBR), la unidad  
puede no mostrar el tiempo real transcurrido.  
2 Presione [PLAY O], la reproducción contin-  
uará desde el punto donde se paró la repro-  
ducción.  
MENÚ DE DISCO  
PLAY  
Para cancelar el modo de reanudación, presione  
dos veces [STOP C].  
Para MP3, la reproducción se reanudará desde el  
1 Presione [DISC MENU].  
principio de la pista actual.  
DISC  
MENU  
La información de reanudación permanece activa-  
da incluso cuando apaga el interruptor principal.  
Aparecerá el menú principal de DVD.  
Si esta función no está disponible,  
lo puede aparecer en la pantalla del televisor.  
Si el menú de disco está disponible en el disco,  
aparecerán las opciones de idioma de audio, de  
subtítulos, capítulos del título y otras para su  
selección.  
el símbo-  
2 Presione [  
K], [L], [s] o [B] para seleccionar  
un ítem y presione [ENTER] para confirmar la  
selección.  
ENTER  
- 45 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MEMO  
- 46 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MEMO  
- 47 -  
ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or  
workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Certain parts and LCD image burn-in are not covered under this  
warranty.  
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE  
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH  
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to  
any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE  
CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED  
SERVICE CENTER.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT  
PRIOR NOTICE.  
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please  
contact us at:  
FUNAI CORPORATION  
Customer Service  
Tel :1-800-968-3429  
19900 Van Ness Avenue, Torrance, CA 90501  
Printed in China  
1EMN20989  
L3151UB ★★★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Car Stereo System CD C482 User Manual
Sharp Car Video System LC 39LE650E V User Manual
Sharper Image MP3 Player SI738 User Manual
Sony DVD Player DVP NC85H User Manual
Sony Kitchen Entertainment Center VGN CR100 User Manual
Sony Photo Printer DPP FP67 User Manual
Sony Speaker System CMT HX9DAB User Manual
Stiga Lawn Mower 11 5234 23 User Manual
Stiga Trimmer SH 60 PRO User Manual
Sylvania MP3 Player SRCD670 User Manual