Sylvania TV DVD Combo 6719DB1 User Manual

OWNER’S

MANUAL

19-INCH COLOR TV/DVD/VHS

6719DB1

This Owner’s Manual is

made of recycled paper.

SUPPLIED ACCESSORIES

ACCESSORIES

Remote Control Unit N0288UD

Batteries 2 AA Batteries

PART NO.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

If you need additional operating assistance after reading this owner’s

manual or to order replacement accessories, please call

TOLL FREE : 1-800-968-3429.

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/DVD/VHS, be sure

the antenna or cable system is grounded so as to provide

some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/DVD/VHS

from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/DVD/VHS.

c. If the TV/DVD/VHS has been exposed to rain or water.

d. If the TV/DVD/VHS does not operate normally by follow-

ing the operating instructions. Adjust only those controls

that are covered by the operating instructions, as improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the TV/DVD/VHS to its normal operation.

14.Lightning-For added protection for this TV/DVD/VHS

receiver during a lightning storm, or when it is left unat-

tended and unused for long periods of time, unplug it from

the wall outlet and disconnect the antenna or cable system.

This will prevent damage to the TV/DVD/VHS due to

lightning and power-line surges.

e. If the TV/DVD/VHS has been dropped or damaged in any

way.

f. When the TV/DVD/VHS exhibits a distinct change in per-

formance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

16.Overloading-Do not overload wall outlets and extension

21.Safety Check-Upon completion of any service or repairs to

this TV/DVD/VHS, ask the service technician to perform

routine safety checks to determine that the TV/DVD/VHS

is in proper operating condition.

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/DVD/VHS through openings as they may

touch dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the TV/DVD/VHS.

22.Heat-This TV/DVD/VHS product should be situated away

from heat sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/DVD/VHS

yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

_{Download from Www.Somanuals.c}-_om3_.-_{All Manuals Search And Download.}

1B15

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

- 4 -

1B15

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

LOCATION

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a TV/DVD/

VHS which has moisture, it may damage the DVD

and TV/DVD/VHS. Therefore when the condensation

occurs inside the unit, turn the POWER button on

and allow at least 2 hours for the unit to dry out.

For safe operation and satisfactory performance of

your TV/DVD/VHS, keep the following in mind

when selecting a place for its installation:

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top and bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/DVD/VHS near strong magnetic

fields.

•

Avoid moving TV/DVD/VHS to locations where

temperature differences are extreme.

•

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the

TV/DVD/VHS disc loading tray.

•

Do not place anything directly on top of the unit.

•

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

The serial number of this product may be found on the back of the unit. No other TV/DVD/VHS has the same

serial number as yours. You should record the number and other vital information here and retain this book as

a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

_{Download from Www.Somanuals.c}-_om5_.-_{All Manuals Search And Download.}

1C29

TABLE OF CONTENTS

TRACKING ADJUSTMENT . . . . .26

SLOW MOTION . . . . . . . . . . . . . .26

PICTURE SEARCH . . . . . . . . . . . .26

STILL PICTURE . . . . . . . . . . . . . .26

VERTICAL HOLD CONTROL . . .26

DVD SECTION

C IMPORTANT SAFEGUARDS . . . . .2

C ABOUT THE DISCS . . . . . . . . . . . .36

PLAYABLE DISCS . . . . . . . . . . . .36

DISC TYPES . . . . . . . . . . . . . . . . .36

C PRECAUTIONS . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

SYMBOLS USED IN

THIS MANUAL . . . . . . . . . . . . . . .36

WARNING . . . . . . . . . . . . . . . . . . . .5

C SPECIAL PLAYBACK . . . . . . . . . .27

RENTAL PLAYBACK . . . . . . . . . .27

AUTO REPEAT PLAYBACK . . . . .27

C PLAYING A DISC . . . . . . . . . . . . . .37

C FEATURES . . . . . . . . . . . . . . . . . . . .7

PLAYING A DVD VIDEO OR AN

AUDIO CD . . . . . . . . . . . . . . . . . . .36

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . . . . .9

C SEARCH . . . . . . . . . . . . . . . . . . . . .28

ZERO RETURN . . . . . . . . . . . . . . .28

TIME SEARCH . . . . . . . . . . . . . . .28

INDEX SEARCH . . . . . . . . . . . . . .29

USING THE DVD MENUS . . . . . .36

USING THE TITLE MENU . . . . . .36

C PREPARATION FOR USE . . . . . . .11

ANTENNA/CABLE

CONNECTIONS . . . . . . . . . . . . . . .11

RESUMING PLAYBACK

FROM THE POINT WHERE

PLAYBACK STOPPED . . . . . . . . .38

CONNECTING TO EXTERNAL

INPUT JACKS . . . . . . . . . . . . . . . .12

C SPECIAL FEATURES . . . . . . . . . .29

REAL TIME TAPE COUNTER . . .29

AUTO REWIND-EJECT . . . . . . . .29

FAST FORWARD/REVERSE . . . . .38

INSTALLING THE BATTERIES . .12

EXTERNAL INPUT MODE . . . . . .12

PAUSING PLAYBACK OR DIS-

PLAYING

A STILL PICTURE . . . . . . . . . . . . .38

C RECORDING . . . . . . . . . . . . . . . . .30

CONNECTING TO A DOLBY

DIGITAL DECODER,

DTS DECODER, OR MPEG

DECODER (for DVD) . . . . . . . . . .13

STEPPING THROUGH FRAMES .38

SLOW MOTION . . . . . . . . . . . . . .39

NORMAL RECORDING . . . . . . . .30

SKIPPING UNWANTED SCENES

DURING

RECORDING . . . . . . . . . . . . . . . . .30

PLAYING FROM A DESIRED

TITLE OR CHAPTER . . . . . . . . . .39

CONNECTING TO A STEREO

SYSTEM (for DVD) . . . . . . . . . . . .14

STARTING FROM A DESIRED

OTR (One Touch Recording) . . . . . .31

CONNECTING TO AN AMPLIFIER

EQUIPPED WITH DIGITAL INPUT

JACKS SUCH AS MD DECK OR

DAT DECK (for DVD) . . . . . . . . . .14

TIME COUNT . . . . . . . . . . . . . . . . .39

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .31

STARTING FROM A DESIRED

TRACK . . . . . . . . . . . . . . . . . . . . . .39

C TIMER . . . . . . . . . . . . . . . . . . . . . .32

REPEAT . . . . . . . . . . . . . . . . . . . . .40

A-B REPEAT . . . . . . . . . . . . . . . . .40

PROGRAM (Audio CD) . . . . . . . . .41

RANDOM (Audio CD) . . . . . . . . . .41

ZOOM PLAYBACK . . . . . . . . . . . .41

AUTOMATIC

TIMER RECORDING . . . . . . . . . .32

C SET UP FOR USE . . . . . . . . . . . . .15

CHANNEL SET UP

FOR THE FIRST TIME . . . . . . . . .15

TIMER PROGRAM EXTENSION .33

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . .34

DELETING (OR ADDING)

CHANNEL . . . . . . . . . . . . . . . . . . .15

AUTO RETURN . . . . . . . . . . . . . . .34

SLEEP TIMER . . . . . . . . . . . . . . . .34

CHANNEL SET UP AGAIN . . . . . .16

SELECTING THE LANGUAGE . .16

DAYLIGHT-SAVING TIME . . . . . .16

C SETTINGS . . . . . . . . . . . . . . . . . . .42

CHANGING THE AUDIO

LANGUAGE OR SOUND MODE .42

C ON SCREEN DISPLAY . . . . . . . . .35

CHANGING THE SUBTITLE

LANGUAGE . . . . . . . . . . . . . . . . .43

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . . . . .17

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .35

CHANGING THE CAMERA

ANGLE (Multi-Angle Pictures) . . . .43

TV/VCR SECTION

C TV OPERATION . . . . . . . . . . . . . . .19

WATCHING A TV PROGRAM . . .19

DEGAUSSING . . . . . . . . . . . . . . . .19

PICTURE CONTROL . . . . . . . . . . .19

CLOSED CAPTION SYSTEM . . . .20

V-CHIP SET UP . . . . . . . . . . . . . . .21

CHANGING THE ON-SCREEN

DISPLAY . . . . . . . . . . . . . . . . . . . .44

C CHANGING THE SETUP ITEMS .45

LANGUAGE SETTINGS . . . . . . . .45

VIDEO SETTINGS . . . . . . . . . . . . .46

AUDIO SETTINGS . . . . . . . . . . . .46

PARENTAL LOCK . . . . . . . . . . . . .47

OTHER SETTINGS . . . . . . . . . . . .48

C MTS(Multi-Channel Television

sound)SYSTEM . . . . . . . . . . . . . . . .23

CHECKING THE SELECTED

MTS MODE . . . . . . . . . . . . . . . . . .23

C LANGUAGE CODE LIST . . . . . . . .49

MTS RECORDING/MONITOR

MODE . . . . . . . . . . . . . . . . . . . . . .23

C TROUBLESHOOTING GUIDE . . .50

C MAINTENANCE . . . . . . . . . . . . . . .53

SELECTING THE MTS SYSTEM .24

DISC HANDLING . . . . . . . . . . . . .53

C VIDEO CASSETTE . . . . . . . . . . . . .25

C SPECIFICATIONS . . . . . . . . . . . . .54

C PLAYBACK . . . . . . . . . . . . . . . . . . .26

C WARRANTY . . . . . . . . . . .Back Cover

NORMAL PLAYBACK . . . . . . . . .26

- 6 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

TV/VCR

Hi-Fi system–The Hi-Fi stereo recording system

offers you excellent sound quality with a dynamic

range of 80dB, frequency response from 20Hz to

20kHz, and 0.005% wow and flutter.

Rotary 4-head Record/Playback System–Four heads

ensure excellent picture quality and special effects playback.

Index Search–Fast-forwards to start of next recording.

Slow Motion–View recorded program at slower

than normal speed.

Infrared remote control

Trilingual on screen tv/vcr setup display selec-

table in English or Spanish or French

Real time counter–This shows the elapsed recording

or playback time in hours, minutes, and seconds. The

“–” indication will appear when the tape is rewound

further than the tape counter position “0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

function from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Auto power on and off system–Automatically

turns on the TV/DVD/VHS when you insert the

cassette, turns off after auto-rewind, and ejects

when the beginning of the tape is reached.

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

Zero Return–The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

Still–“Freeze” the picture at any time, for close

viewing of a particular scene.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Let you set the TV/DVD/VHS to

advance the tape by entering the desired playback

time you want to skip.

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts, and the Weekly timer allows recording to be

made once a week up to the end of the tape.

•

Auto return–After timer recording is finished, the

TV/DVD/VHS can return to the beginning of the

recording.

Sleep timer–Allows you to have the TV/DVD/VHS

automatically turn on or off at a desired time. (This

feature is not available for DVD mode.)

•

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

_{Download from Www.Somanuals.c}-_om7_.-_{All Manuals Search And Download.}

1C29

DVD

¡Dolby Digital sound

¡DTS (Digital Theater System)

This player can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby Digital

decoder.

Sound system different from Dolby Digital sound system

¡Search

Chapter search: Search for the chapter designated by user

is possible.

¡Still/fast/slow/step playback

Various playback modes are available including still pic-

tures, fast forward/reverse, slow motion and step frames.

Title search:

Search for the title designated by user is

possible.

Track search: Search for the track designated by user is

¡Random playback for audio CD

This player can shuffle the order of tracks to play them in

random order.

possible.

Time search: Search for the time designated by user is

possible.

¡Program playback for audio CD

You can program the order of tracks to play them in any

desired order.

¡Repeat

Chapter:

Repeated playback of the chapter of the

disc being played is possible.

Repeated playback of the title of the disc

being played is possible.

Repeated playback of the track of the disc

being played is possible.

¡DVD menus in a desired language

You can display DVD menus in a desired language, if

available on a DVD.

Title:

Track:

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no input

from the player for five minutes in the stop mode. When

the screen saver program is activated for 30 minutes, the

DVD power is automatically turned off, and "DVD"

appears on the screen.

Disc(audio CD): Repeated playback of the entire disc being

played is possible.

A-B:

The part between A and B designated by

user is possible.

¡Zoom

4-time magnified screen can be displayed.

¡Subtitles in a desired language

You can select a desired language for the display subtitles,

if that language is available on a disc.

¡Marker

The part designated by user can be called back.

¡Selecting a camera angle

You can select the desired camera angle, if a disc contains

sequences recorded from different angles.

¡Resume Play

User can resume to playback from the part at which the

play was stopped.

¡Choices for audio language and sound mode

You can select the desired audio language and sound

mode, if different languages and modes are available on a

disc.

¡SRS TruSurround

You can enjoy stereophonic virtual space on your existing

stereo system.

¡Dimmer

Brightness of the display can be varied.

¡Parental lock

You can set the control level to limit playback of discs

which may not be suitable for children.

¡Bit rate indication

¡Dynamic range control

¡Automatic detection of discs

This player automatically detects if a loaded disc is DVD

or audio CD.

¡On-screen display

Information about the current operation can be displayed

on a TV screen, allowing you to confirm the currently

active functions (such as program playback), on the TV

screen using the remote control.

This unit employs TruSurround system

of SRS Labs, Inc. as virtual

technology.

TruSurround and the

SRS Labs, Inc.

symbol are trademarks of

TruSurround technology is incorporated under license

from SRS Labs, Inc.

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

- 8 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- TV/DVD/VHS FRONT PANEL - [Fig.1]

DVD buttons

TV/VCR buttons

POWER

VOLUME

SKIP

PLAY

SKIP

STOP

OPEN/CLOSE

SELECT

CHANNEL

REC/OTR REW

PLAY F.FWD STOP/EJECT

AUDIO

HEADPHONE VIDEO

DVD

TV/VCR

3 4 3

7 8 9 10 11 12 13 14

15 1617 18 19 20 21

6.OPEN/CLOSE button

Press to insert discs into or remove them from the

tray.

[Fig. 2]

- REMOTE CONTROL -

7.Disc loading tray

8.DVD indicator

POWER PICTURE SLEEP SELECT

Lights on during DVD mode.

9.SELECT button

Press to change to TV/VCR mode or DVD mode.

NOTE: For about 4 seconds just after the DVD

mode has switched to the TV mode, the button

does not work to switch back to the DVD mode.

CH.

VOL.

PAUSE

+100

+10

10. TV/VCR indicator

SPEED C.RESET

ZOOM

MUTE

Lights on during TV/VCR mode.

11. CHANNEL K/L buttons

PLAY

STOP

Press to select memorized channel.

3 (DVD)

15 (TV/VCR)

(DVD) 3

^(TV/VCR)4¹⁴

12. Recording indicator

DISC

Flashes during recording. Lights up in the Stand-

by mode for Timer Recording.

RECORD

DISPLAY

SETUP

ENTER

13. REC/OTR (RECORD) button

TITLE

RETURN

Press for manual recording. Activates One Touch

Recording. (OTR is only during TV/VCR mode.)

CLEAR SEARCH MODE REPEAT

A-B

14. REW button (for TV/VCR)

AUDIO SUBTITLE ANGLE

MODE

Press to rewind the tape, or to view the picture

rapidly in reverse during playback mode. (Rewind

Search)

15. FWD button (for TV/VCR)

Press to rapidly advance the tape, or to view the

picture rapidly in forward during playback mode.

(Forward Search)

16. STOP/EJECT button

1.POWER button

Press to stop the tape motion. Press in the Stop

mode to remove tape from the unit.

Press to turn the power on and off.

2.VOLUME K/L buttons

Press to control the volume level for the DVD and TV.

3.SKIP buttons (for DVD)

Skip chapters or tracks to a desired point.

4.PLAY button

Starts playback of the disc or tape contents.

5.STOP button

Stops operation of the disc or tape.

17. Remote sensor window

18. HEADPHONE jack

To connect headphone (not supplied) for personal

listening.

19. VIDEO input jack

Connect to the video output jack of a video

camera or VCR.

_{Download from Www.Somanuals.c}-_om9_.-_{All Manuals Search And Download.}

1C29

- TV/DVD/VHS REAR PANEL - [Fig.3]

ANT.

AUDIO OUT

COAXIAL

48 49

20. AUDIO L/R input jacks

Connect to the audio output jacks of a video

camera or VCR.

31. MODE button

Activates program playback or random playback mode.

32. SEARCH MODE button

21. Cassette compartment

Press to locate a desired point.

22. PICTURE button

33. AUDIO button

Press to adjust the picture.

Press to select a desired audio language or sound

mode.

23. Number buttons

34. SUBTITLE button

TV Mode:

Press to select a desired subtitle language.

Press two digits to directly access the desired

channel.

Remember to press a "0" before a single digit

channel.

+100 button–

Press to select cable channels which are equal or

greater than number 100.

DVD Mode:

Press to enter the desired number.

+10 button–

35. REPEAT button

Repeats playback of the current disc, title, chapter

or track.

36. ANGLE button (DVD mode)

Press to change the camera angle to see the

sequence being played back from a different angle.

SLEEP button (TV/VCR mode)

Sets the Sleep Timer. (See page 34.)

37. A-B REPEAT button

Press to enter the desired numbers which are

equal or greater than number 10.

Repeats playback of a selected section.

38. RETURN button

24. PAUSE button

Returns to the previous operation.

Pauses the current disc or tape operation.

39. ENTER button

25. SPEED button

Press to accept a setting.

Press to choose the desired recording speed:

SP/SLP.

40. Arrow buttons

TV/VCR Mode:

26. C.RESET button

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

DVD Mode:

Use when making settings while watching the

display on a TV screen.

Press to reset counter to 0:00:00.

Press to cancel a setting of timer program. (See

page 33.)

27. DISPLAY button

TV/VCR Mode:

Display the counter or the current channel number

and current time on the TV screen.

DVD Mode:

Displays the current status on the TV screen for

checking purposes.

41. DISC MENU button

Displays the menus in the DVD.

42. ZOOM Button

Enlarges part of a DVD-reproduced image.

43. MUTE button

28. SETUP button

Mutes the sound. Press it again to resume sound.

Press to enter or exit the TV menu or DVD setup

mode.

44. DVD button

Press to switch to DVD mode. DVD indicator on

the front will lights on.

29. TITLE button

Displays the title menu.

45. TV/VCR button

30. CLEAR button

Resets a setting.

- 10 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

Press to switch to TV/VCR mode. TV/VCR indi-

cator on the front will lights on.

Connect to the digital input of an external

amplifier or decoder.

46. ANT. in jack

49. AUDIO L/R output jack

Connect to an antenna, cable system, or satellite

system.

Connect to the analog audio input of an external

amplifier or decoder.

47. Power cord

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook to

avoid breaking a wire before you connect

to a standard AC outlet.

48. COAXIAL digital audio out jack

PREPARATION FOR USE

ANTENNA/CABLE CONNECTION

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box (Not supplied)

OUT

From Cable System or

Satellite Dish

VHF Antenna (Not supplied)

75-ohm

Coaxial

Cable

UHF Antenna

(Not supplied)

From Cable

System

(Not sup-

plied)

ANT.

AUDIO OUT

VHF/UHF

COAXIAL

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not

[Fig. 4]

supplied)

Flat twin-lead cable

VHF/UHF SEPARATE ANTENNAS

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

In some areas it will be necessary to use an outdoor

antenna.

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in the illustration.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/DVD/VHS Remote Control. Unattended timer

recording is limited to one channel at a time.

Use this connection if your cable system connects

directly to your TV/DVD/VHS without a converter

box.

By using this connection you can:

1) Use the TV/DVD/VHS remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

Antenna/Cable Connections

Continued on the Next Page.

NOTE: This unit will ONLY record and view the

same channel.

- 11 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TO RECORD A SCRAMBLED/UNSCRAM-

BLED CHANNEL

INSTALLING THE BATTERIES

1. Set the TV/DVD/VHS channel selector to the out-

put channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

Note to CATV system installer:

3)Replace the cover.

This reminder is provided to call the CATV sys-

tem installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper ground-

ing and, in particular, specifies that the cable

ground shall be connected to the grounding sys-

tem of the building as close to the point of cable

entry as practical.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO L/R IN/

CONNECTING TO EXTERNAL

INPUT JACKS

When you watch a program recorded on an another

source (VCR or video camera), use the audio/video

input jacks on the front of the TV/DVD/VHS.

Connect the audio/video output jacks of another

source to the AUDIO L/R and VIDEO jacks of this

TV/DVD/VHS.

AUX

VIDEO IN jacks of your

TV/DVD/VHS. Then press the

CHANNEL K or L button until

“AUX” appears on the screen.

Then press the SELECT button until "VIDEO"

appears on the screen.

NOTE:

When you connect a monaural VCR (another

•

source) to this TV/DVD/VHS, connect the Audio

output jack of the monaural VCR (another source)

to the AUDIO L jack of this TV/DVD/VHS. The

audio will output in both L and R channel equally.

To the audio

output jacks

[Another source]

HEADPHONE

VIDEO

L-AUDIO-R

Audio/Video

coaxial cable

(not supplied)

etc.

To the video

[Front of the

TV/DVD/VHS]

output jack

[Fig. 5]

- 12 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A DOLBY DIGITAL DECODER,

DTS DECODER, OR MPEG DECODER (for DVD)

If using this TV/DVD/VHS to play back a TV/DVD/VHS in a 5.1 channel Dolby Digital surround, DTS sur-

round, or MPEG surround format, the TV/DVD/VHS outputs a Dolby Digital, DTS, or MPEG data stream from

its COAXIAL DIGITAL AUDIO OUT jack. By hooking the player up to a Dolby Digital or DTS decoder, you

can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound of a profes-

sional standard such as can be heard in movie theaters.

Use audio coaxial digital cables (commercially available) for the audio connections.

Center

speaker

ANT.

Front speaker

(left)

Front speaker

(right)

AUDIO OUT

COAXIAL

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

Dolby Digital

or DTS decoder

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 8]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VHS.

If output Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio

output in the setup mode.

•

If output DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode.

If played a disc indicated MPEG audio, connect to a MPEG decoder, and set MPEG to ON for audio output

in the setup mode.

•

Unless connected to a Dolby Digital decoder, a DTS decoder, or a MPEG decoder, set Dolby Digital, DTS,

or MPEG to off for audio output in the setup mode. Playing a TV/DVD/VHS using incorrect settings may

generate noise distortion, and may also damage the speakers.

•

When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and

you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.

•

Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D

symbol are trademarks of Dolby

Laboratories.

“DTS” and “DTS Digital Out” are trade-

marks of Digital Theater Systems Inc.

- 13 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A STEREO SYSTEM (for DVD)

ANT.

AUDIO OUT

Stereo system

COAXIAL

To Right (red) and Left (white)

AUDIO OUT jacks

(only DVD AUDIO OUT)

To ANALOG AUDIO INPUT jacks

[Fig. 6]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the

TV/DVD/VHS.

•

CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL

INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)

Use an audio coaxial digital cable (commercially available) for the audio connections.

Connecting to an amplifier equipped with digital input jacks such as MD Deck or Dat Deck.

ANT.

AUDIO OUT

COAXIAL

Amplifier equipped with digital

input jacks, MD deck,

DAT deck, etc.

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

To COAXIAL DIGITAL

AUDIO INPUT jack

(only DVD AUDIO OUT)

[Fig. 7]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VHS.

Set DOLBY DIGITAL and DTS to OFF for audio output in the setup mode. Playing a TV/DVD/VHS using

incorrect settings may generate noise distortion, and may also damage the speakers.

When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and

you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.

•

- 14 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TV/VCR SECTION

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just

select the TV/DVD/VHS channel selector to the output channel of the cable box or satellite box (Ex CH3).

Then select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

FIRST TIME

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

1 Plug in the TV/DVD/VHS power cord

Plug the TV/DVD/VHS power cord

into a standard AC outlet.

NOTE:

1 Select “CHANNEL SET UP”

- TV/VCR SETUP -

If some digits appear in the corner of

•

TIMER PROGRAMMING

SETTING CLOCK

the screen, press the POWER button

without unplugging the power cord.

Press the SETUP button on the

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

remote control.

Press the Arrow K or L button to

point to “CHANNEL SET UP”.

Then, press the Arrow B button.

TIME SEARCH

INDEX SEARCH

2 Turn on the TV/DVD/VHS

Press the POWER button to turn on the TV/DVD/VHS.

2 Select “ADD/DELETE CH”

Press the Arrow K or L button to

point to “ADD/DELETE CH”.

Press the Arrow B button.

– CHANNEL SET UP –

3 Select “ENGLISH” or “ESPAÑOL” or

“FRANÇAIS”

ADD / DELETE CH (TV)

AUTO PRESET

– SET UP –

Select “ENGLISH” or

LANGUAGE

[ENGLISH] ESP

FRA

“ESPAÑOL”=Spanish or

AUTO PRESET

“FRANÇAIS” =French using the

Arrow B or s button. “[ ]” indi-

cate the selected language.

3 Enter the desired channel number

Press the Arrow K or L button until

your desired channel number

appears. (You can also use the num-

ber buttons or the CHANNEL K/L

button to enter it) (Example: CH8)

4 Begin auto preset

– SET UP –

Press the Arrow K or L button to

point to “AUTO PRESET”.

Then press the Arrow B button.

The tuner scans and memorizes all

active channels in your area.

LANGUAGE

[ENGLISH] ESP

FRA

ADD / DELETE

AUTO PRESET

4 Delete (or add) it from (into) memory

Press the Arrow B or s button. The channel number

changes to light red. The channel is deleted from

memory.

NOTES:

The TV/DVD/VHS distinguishes between standard

TV channels and cable channels.

•

If you want to play or record a video tape

BEFORE presetting the tuner, you must press the

SETUP button on the remote control. To preset the

tuner again, see “CHANNEL SET UP AGAIN” on

page 15.

The TV/DVD/VHS may memorize TV channels as

CATV channels if reception conditions is poor. If

this happens, try AUTO MEMO action again when

reception conditions are better.

•

To delete another channel, repeat steps [3] and [4].

If you press the Arrow B or s button again, the

channel is memorized again.

•

5 Exit the channel setup mode

•

Added channel: Light blue.

Deleted channel: Light red.

Press the SETUP button on the remote control to

returns to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

5 After scanning

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with the remote

control number buttons or CHANNEL K or L.

- 15 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE: If Spanish or French is selected accidentally,

press the SETUP button on the remote control, press

the Arrow K button to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE” [FRANÇAIS], then

press the Arrow B button, then press the SETUP

button on the remote control.

CHANNEL SET UP AGAIN

Make sure ...

Press the POWER button to turn on the

TV/DVD/VHS.

•

1 Select “CHANNEL SET UP”

DAYLIGHT-SAVING TIME

Select this feature and the TV/DVD/VHS’s clock

automatically will advance one hour in April, then

reverse one hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Press the SETUP button on the

remote control.

Press the Arrow K or L button to

point to “CHANNEL SET UP”.

Then, press the Arrow B button.

First Sunday of April : At 2 AM the clock imme-

•

2 Begin auto preset

Press the Arrow K or L button to

point to “AUTO PRESET”.

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

– CHANNEL SET UP –

ADD / DELETE CH (TV)

AUTO PRESET

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

Then, press the Arrow B button.

The tuner scans and memorizes all

the active channels in your area.

•

Press the POWER button to turn on the

TV/DVD/VHS.

•

3 After scanning

The tuner stops on the lowest memorized channel.

1 Select “SETTING CLOCK”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the SETUP button on the

remote control.

SELECTING THE LANGUAGE

Make sure ...

Press the Arrow K or L button to

point to “SETTING CLOCK”.

Then, press the Arrow B button.

TIME SEARCH

INDEX SEARCH

Press the POWER button to turn on the

TV/DVD/VHS.

•

NOTE: This function effects only the language on

the screen menu and not the audio source.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the Arrow K or L button to

– SETTING CLOCK –

point to “D.S.T.”.

Then, press the Arrow B or s but-

ton until [ON] appears.

- TV/VCR SETUP -

AUTO CLOCK

[ON]

1 Select “LANGUAGE”

TIMER PROGRAMMING

SETTING CLOCK

AUTO CLOCK CH

[AUTO]

[ON]

CHANNEL SET UP

Press the SETUP button on the

USER’S SET UP

MANUAL CLOCK SET

D.S.T.

V-CHIP SET UP

remote control.

Press the Arrow K or L button to

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

point to “LANGUAGE”.

3 Exit the Daylight-Saving Time mode

Press the SETUP button on the remote control to

return to TV mode.

2 Select “ENGLISH” or “ESPAÑOL” or

“FRANÇAIS”

Select “ENGLISH” or “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the Arrow B or

button.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the Arrow

B or s button.

3 Exit the Language mode

Press the SETUP button on the remote control to

return to TV mode.

- 16 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOCK SET UP

– SETTING CLOCK –

2 Set “AUTO CLOCK” to [ON]

Press the Arrow B or s button

repeatedly until [ON] appears.

(AUTO / MANUAL)

AUTO CLOCK

[ON]

AUTO CLOCK CH

[AUTO]

[OFF]

Set the clock accurately for proper automatic timer

recording. If the Public Broadcasting Station (PBS) is

available in your area, follow “AUTO CLOCK SET-

TING”. If it is not, follow “MANUAL CLOCK SET-

TING”.

MANUAL CLOCK SET

D.S.T.

3 Enter the channel number for the PBS station

Press the Arrow K or L button to

point to “AUTO CLOCK CH”.

– SETTING CLOCK –

AUTO CLOCK SETTING

AUTO CLOCK

[ON]

You can have the TV/DVD/VHS set the clock auto-

matically by using the Public Broadcasting Station

(PBS) channel in your area. Once you have set the

clock by using the following procedure, the

TV/DVD/VHS will automatically monitor the correct

time and date being broadcast by the PBS station in

your area, using a new service called Extended Data

Service (XDS).

AUTO CLOCK CH

[AUTO]

Then press the Arrow B or s but-

ton until the channel number for

your local PBS station appears.

MANUAL CLOCK SET

D.S.T.

[OFF]

If you do not know the PBS channel number, leave it

set to [AUTO] which is located before [2]. The

TV/DVD/VHS will search automatically all available

channels for the local PBS station, and will select

that channel.

Make sure ...

TV/DVD/VHS power must be turned on.

Confirm that the antenna connections are correct.

The cable converter box must be turned on if your

TV/DVD/VHS is connected directly to it. (See

NOTES:)

•

4 Exit the Auto Clock Setting

Press the SETUP button on the remote control to

return to TV mode.

•

5 Turn off the TV/DVD/VHS

Turn the TV/DVD/VHS off. Because the Auto Clock

functions automatically while the TV/DVD/VHS is

off.

The channel is properly set in advance. (See page

16.)

•

NOTES:

Auto clock setting only needs to be set once. But it

can be done again if the clock’s time has become

incorrect for some reason.

•

If you choose [AUTO],

the TV/DVD/VHS must search until the PBS chan-

•

nel is found. It must scan each channel for a couple

of seconds to determine if that channel is transmit-

ting the XDS signal.

If the TV/DVD/VHS is connected directly to a

•

cable converter box or satellite box, the local PBS

station must be selected on the cable box itself, and

the TV/DVD/VHS must be set to the output chan-

nel of the cable converter box or satellite box (usu-

ally channel 3 or 4), to be able to set up or correct

the clock automatically.

If you do not know what your local PBS station is,

then follow “Manual Clock Settings” on page 18.

The TV/DVD/VHS cannot control the channels of

the cable converter box or satellite box.

if the time, that is automatically set by this selected

•

PBS station is incorrect, it may not be your local

PBS station, but one from a different time zone. Or

there is a case that no channel is broadcasting the

XDS signal in your area, as shown by no time. In

these cases, you must manually enter the correct

local PBS station, or set the clock manually and

turn off the Auto Clock Setting feature.

1 Select “SETTING CLOCK”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the SETUP button on the

remote control.

Press the Arrow K or L button to

point to “SETTING CLOCK”.

Then, press the Arrow B button.

TIME SEARCH

INDEX SEARCH

- 17 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

MANUAL CLOCK SETTING

Make sure ...

In the example below, the clock is to be set to:

DATE May 7th, 2002

TV/DVD/VHS power must be turned on.

•

SETTING TIME 5:40PM

1 Select “SETTING CLOCK”

6 Select the hour

Press the Arrow K or L button until

your desired hour appears.

(Example: 5, PM)

– MANUAL CLOCK SET –

MONTH DAY YEAR

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Press the SETUP button on the

remote control.

0 5

0 7 TUE 2 0 0 2

HOUR

0 5

MINUTE

– – PM

Press the Arrow K or L button to

point to “SETTING CLOCK”.

Then, press the Arrow B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the Arrow K or L button until

the desired minute appears.

(Example: 40)

2 Select “MANUAL CLOCK

SET”

Press the Arrow K or L button to

point to “MANUAL CLOCK SET”.

Then, press the Arrow B button.

– SETTING CLOCK –

0 5

0 7 TUE 2 0 0 2

AUTO CLOCK

[ON]

HOUR

0 5

MINUTE

4 0 PM

AUTO CLOCK CH

[AUTO]

[OFF]

MANUAL CLOCK SET

D.S.T.

8 Start the clock

Press the SETUP button on the

remote control.

Although seconds are not displayed,

they begin counting from 00 when

you press the SETUP button on the

5:40 PM

3 Select the month

– MANUAL CLOCK SET –

MONTH DAY YEAR

Press the Arrow K or L button until

your desired month appears.

(Example: May → 05)

0 5

– – – – – – – – –

HOUR

– –

MINUTE

– – – –

remote control. Use this feature to synchronize the

clock with the correct time.

Then, press the Arrow B button.

NOTE:

4 Select the day

– MANUAL CLOCK SET –

MONTH DAY YEAR

When unplugging the AC cord or if there is a power

failure for more than 30 seconds, you may have to

reset the clock.

Press the Arrow K or L button until

your desired day appears.

(Example: 7th → 07)

0 5

0 7 – – – – – – –

HOUR

– –

MINUTE

– – – –

Then, press the Arrow B button.

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps [1] and [2].

2)Select where you want to change using the Arrow

B or s button.

3)Enter correct numbers using the Arrow K or

button.

5 Select the year

Press the Arrow K or L button until

your desired year appears.

(Example: 2002)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 7 TUE 2 0 0 2

HOUR

– –

MINUTE

– – – –

Then, press the Arrow B button.

4)Press the SETUP button on the remote control to

start the clock.

PLEASE NOTE:

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the Arrow B or s button to turn [OFF] this

function. Then you can manually adjust the clock.

- 18 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/DVD/VHS’s picture controls – BRIGHT,

CONTRAST, COLOR, TINT and SHARPNESS –

are preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

1 Turn on the TV/DVD/VHS

Press the POWER button to turn on the

TV/DVD/VHS.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/DVD/VHS is connected to a

cable box or satellite box, the TV/DVD/VHS must be

on CH3 or CH4, then the channel to be viewed must

be selected on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/DVD/VHS power must be turned on.

•

1 Select “PICTURE CONTROL”

Press the PICTURE button on the remote control.

3 Adjust sound

Press the VOLUME or button

to adjust the volume.

VOLUME 20

2 Select item you want to adjust

Press the Arrow K or L button until desired control

is displayed.

NOTES:

If you press the CHANNEL o or p in the DVD

mode, you can change the TV channels.

Even if you turn off the TV/DVD/VHS in the DVD

mode, when you turn it on again, it will go into the

TV/VCR mode.

•

BRIGHT

CONTRAST

COLOR

TINT

BRIGHT

–

P +

SHARPNESS

DEGAUSSING

3 Adjust the picture control

Magnetism from nearby appliances might affect the

color of the TV picture.

Press the Arrow B or s button to adjust to your

desired level.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect power

cord from AC outlet then reconnect it after 30 minutes.

Arrow

BRIGHT

to decrease

brightness

to decrease

contrast

to increase

brightness

to increase

contrast

CONTRAST

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

to purple

to green

to clear

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 19 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news, pre-recorded tapes with either a dia-

logue caption or text display.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

- TV/VCR SETUP -

1 Select “CAPTION”

Press the SETUP button on the

remote control.

Press the Arrow K or L button to

point to “CAPTION”.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2 Select your desired caption menu

Press the Arrow B or s button

until your desired caption menu

appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

NOTE:

3 Exit the caption setting mode

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

Press the SETUP button on the remote control to

return to TV mode.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], select [OFF] using the

Arrow B or s button. Press the SETUP button on

the remote control to return to TV mode.

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

NOTE:

•

WHEN THE CLOSED CAPTION MODE

IS ON

If the TV/DVD/VHS displays a

black box on the TV screen, this

means that the TV/DVD/VHS is set

to the TEXT mode. To clear screen,

select [CAPTION1], [CAPTION2]

or [OFF].

The On-Screen Display will disappear after 5 sec-

onds.

This is also true when the MUTE button is pressed,

and when the PAUSE button is pressed while

recording.

•

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

Make sure ...

TV/DVD/VHS power must be turned on.

•

- 20 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

V-CHIP SET UP

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “TV-Y” to [VIEW], the all ratings

will turn to [VIEW] automatically.

•

V-CHIP enables parents to prevent their children

from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels, and Emergency Broadcast

System signals), then denies access to programming

if the program’s rating meets the limitations you

select. In this case, “PROTECTED PROGRAM by

...” message appears on the TV screen. You can

watch the protected program by entering access code

(default 0000).

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TV-Y7

TV-G

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

To block ratings, follow the steps below.

Programming may be rated by the Motion Picture

•

TV-MA Mature audience only

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

When you select TV-Y7, TV-PG, TV-14, or TV-MA

and you press the Arrow B button, the sub-ratings

will appear on the TV screen.

If you select the rating category (example: TV-PG)

and turn it [BLOCK] or [VIEW], the sub-ratings

(example: V for Violence) will turn [BLOCK] or

[VIEW] automatically.

TV RATING SET UP

Make sure ...

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK].

TV/DVD/VHS power must be turned on.

•

- TV/VCR SETUP -

1 Select “V-CHIP SET UP”

TIMER PROGRAMMING

To set the sub-ratings individually, follow the steps

below.

SETTING CLOCK

CHANNEL SET UP

Press the SETUP button on the

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

When you select [TV-Y7]:

•

remote control.

TV–Y7

[BLOCK]

Press the Arrow L or K button to

select “FV” (Fantasy Violence).

Then, press the Arrow B button

to select [BLOCK] or [VIEW].

Press the Arrow K or L button to

point to “V-CHIP SET UP”.

Then, press the Arrow B button.

INDEX SEARCH

When you select [TV-PG], [TV-14] or [TV-MA]:

Press the Arrow L or K button to

•

2 Input Access code

Use the number buttons to enter 4-

digit access code. The default code

is 0000.

ACCESS CODE

select “D”(Suggestive Dialog),

TV–PG

[BLOCK]

“L”(Coarse Language),

“S”(Sexual Situation), or

“V”(Violence). Then, press the

Arrow B button to select

[BLOCK] or [VIEW].

– V-CHIP SET UP –

3 Select “TV RATING”

Press the Arrow K or L button to

point to “TV RATING”.

TV RATING

MPAA RATING

CHANGE CODE

Note: When you select [TV-MA], “D” does not

appear on the TV screen.

The sub-ratings which set to

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

Then, press the Arrow B button.

(

)

[VIEW]

[BLOCK] appears next to the rat-

ing category in the TV RATING

menu.

[BLOCK]

4 Select your desired item

Press the Arrow K or L button to

point to your desired item.

Then, press the Arrow B button to

select [BLOCK] or [VIEW].

TV–Y

[VIEW]

TV–Y7

TV–G

(

)

TV–PG (

)

TV–14

(

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

return to original mode.

TV–MA(

- 21 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

MPAA RATING SET UP

CHANGE ACCESS CODE

Make sure ...

To change access code, follow the steps.

TV/DVD/VHS power must be turned on.

•

1 Select “V-CHIP SET UP”

Press the SETUP button so that the TV/VCR SETUP

display appears on the TV screen.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Press the SETUP button on the

remote control.

Press the Arrow K or L button to

point to “V-CHIP SET UP”.

Then, press the Arrow B button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

Press the Arrow K or L button to

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

point to "V-CHIP SET UP". Then,

press the Arrow B button.

INDEX SEARCH

ACCESS CODE

Use the number buttons to enter 4-

digit access code. The default code

is 0000.

ACCESS CODE

Use the number buttons to enter 4-

digit access code. The default code

is 0000.

– V-CHIP SET UP –

3 Select “MPAA RATING”

Press the Arrow K or L button to

point to “MPAA RATING”.

TV RATING

MPAA RATING

CHANGE CODE

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

Press the Arrow K or L button to

point to "CHANGE CODE". Then,

press the Arrow B button.

Then, press the Arrow B button.

Selection

Rating Category Explanations

General Audience

NEW CODE

PG-13

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

Use the number buttons to enter

your desired access code in the

NEW CODE space. Then enter the

same code in the CONFIRM

CODE space. V-CHIP SET UP

screen appear on the screen.

CONFIRM CODE

NC-17

NEW CODE

Mature audience only

X X X X

CONFIRM CODE

If you enter wrong code, repeat

•

step 5, making sure you enter the

same new code exactly in the

confirm code space.

4 Select your desired item

Press the Arrow K or L button to

point to your desired item.

Then, press the Arrow B button to

select [BLOCK] or [VIEW].

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

Press the SETUP button to exit the TV/VCR SETUP.

When you select the rating cate-

•

gory and turn it [BLOCK], the higher rating will

turn [BLOCK] automatically. Also, the lower rat-

ing will turn [VIEW] automatically.

Note:

If you unplug the power code or power failure

•

occurs, the changed access code will be lost and

will return to default (0000). Change your access

code again as necessary.

When you turn “G” to [VIEW], the all ratings will

turn to [VIEW] automatically.

•

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

return to original mode.

- 22 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

MTS(Multi-Channel Television sound)SYSTEM

You can record or listen to a program in MTS stereo.

CHECKING THE SELECTED MTS MODE

When you play a VHS tape, or receive a broadcast

1] When a program is broadcast in stereo, STEREO

appears on the TV screen.

2] When a program is broadcast in second audio,

SAP appears on the TV screen.

on the TV/DVD/VHS tuner channel you are watching,

the status shown below will appear when you press

the DISPLAY button on the remote control.

3] When a program broadcast both in stereo and sec-

ond audio, STEREO and SAP appear on the TV

screen.

NOTE: Although a program may be broadcast in

both stereo and second audio, you cannot

record in both stereo and second audio at

the same time.

PLAY

HIFI

12:00AM

CH 123

STEREO/SAP

4] While the TV/DVD/VHS is set in HIFI stereo

mode and playback mode. HIFI appears on the

TV screen. While the TV/DVD/VHS is set in

monaural(MONO) mode, HIFI disappears from

the TV screen.

COUNT

0:00:00

Second Audio Program, which means your

program, can also be received in a second

language or sometimes a radio station.

SAP

NOTE: If you play non-HIFI tapes while the

TV/DVD/VHS is set in HIFI, HIFI will dis-

appear from the TV screen and the

TV/DVD/VHS will play automatically in

monaural.

High Fidelity which produces better sound

than standard stereo TV/DVD/VHSs.

HIFI

MTS RECORDING/MONITOR MODE

Type of broadcast Display on

STEREO/SAP

Hi-Fi audio track(2-channel) Normal audio

the TV screen SELECTION

L-channel

R-channel

track

Regular

-None-

-Invalid-

Mono

(monaural audio)

Stereo broadcast

Bilingual broadcast

STEREO

SAP

-Invalid-

STEREO*

L+R

Main audio

program

Main audio

program

Main audio

program

SAP*

Sub audio

program

Sub audio

program

Sub audio

program

Stereo & Bilingual

broadcast

STEREO

SAP

STEREO*

SAP*

L+R

sub audio

program

sub audio

program

sub audio

program

*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.

- 23 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECTING THE MTS SYSTEM

Make sure ...

TV/DVD/VHS power must be turned on.

TO SELECT MONO MODE

•

You can change the selection to “MONO” if you

want to listen to HIFI tapes in normal audio play-

back.

TO SELECT HIFI MODE

1) Press the SETUP button on the remote control.

- TV/VCR SETUP -

1 Select “USER’S SET UP”

Press the SETUP button on the

remote control.

Press the Arrow K or L button to

point to “USER’S SET UP”. Then,

press the Arrow Bbutton.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Press the Arrow K or L button to point to

“USER’S SET UP”.Then, press the Arrow

button.

2) Press the Arrow K or L button to point to

“VCR AUDIO”. Then, press Arrow Bbutton.

3) Press the Arrow B or s button until [MONO]

appears.

4) Press the SETUP button on the remote control to

return to TV mode.

2 Select“VCR AUDIO”

Press the Arrow K or L button to

point to“VCR AUDIO”. Then, press

the Arrow Bbutton.

– USER’S SET UP –

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

TO SELECT STEREO, SAP, OR MONO

1 Select “USER’S SET UP”

- TV/VCR SETUP -

Press the “SETUP” button on the

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

– USER’S SET UP –

3 Select [HIFI]

Press the Arrow B or s button

until [HIFI] appears.

remote control.

Press the Arrow K or L button to

point to “USER’S SET UP”.Then,

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

INDEX SEARCH

press the Arrow

button.

2 Select “TV AUDIO”

Press the Arrow K or L button to

point to“TV AUDIO”. Then, press

the Arrow Bbutton.

4 To return to TV mode

Press the SETUP button on the remote control to

return to TV mode.

– USER’S SET UP –

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

NOTES:

Normally, “HIFI” should be selected for playback

with HIFI sound.

•

3 Select [STEREO], [SAP], or [MONO]

When you play non-HIFI tapes, the TV/DVD/VHS

will play automatically in the monaural mode.

The TV/DVD/VHS records automatically MTS

broadcasts in HIFI stereo sound unless you select

SAP mode recording before you begin recording.

•

Press the Arrow B or s button until [STEREO],

[SAP], or [MONO] appears.

•

4 To return to TV mode

Press the SETUP button on the remote control to

return to TV mode.

NOTES:

• You must select the recording mode,either TV

AUDIO [STEREO] or [SAP] when you record a

broadcast.

“MTS RECORDING/MONITOR MODE”.

Refer to

• If you select second audio when second audio is not

available, the TV/DVD/VHS will record normal

audio.

- 24 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CASSETTE

This TV/DVD/VHS will operate with any cassette that has the

mark. For best results,

we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/DVD/VHS. The

TV/DVD/VHS will automatically turn on.

•

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/DVD/VHS, wait until the tape has

warmed to room temperature and the moisture has

evaporated.

Window

Avoid extreme heat, high humidity and magnetic

fields.

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

TWO DIFFERENT TAPE SPEEDS

REMOVING A CASSETTE

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

1)In the Stop mode, press the EJECT button on the

remote control or press the STOP/EJECT button on

the TV/DVD/VHS. The cassette will eject.

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

Note: You can play back a tape recorded in LP mode

(Long Play).

ERASE PREVENTION

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

If you decide to record on

the tape again, cover the

hole with plastic tape.

Transparent Tape

- 25 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

NORMAL PLAYBACK

SLOW MOTION

Make sure ...

During pause, press the FWD button to reduce the

playback speed. The TV/DVD/VHS mutes the sound

during slow motion. Press the PLAY button to return

to normal playback.

NOTE: If it is left in the Slow mode for more than

five minutes, the TV/DVD/VHS will automatically

go into the Stop mode.

TV/DVD/VHS power must be turned on.

•

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/DVD/VHS will start playback automatically.

PICTURE SEARCH

PLAY

2 To begin playback

Press the PLAY button.

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button. (in the SP / LP / SLP

modes)

3 To stop playback

Press the STOP button when play-

back is completed.

STOP

NOTE:

If you press the F.FWD or REW button in the

DVD mode, the VCR forward or reverse will start.

Please press the STOP button to stop it.

•

NOTES:

2)Press it again and the TV/DVD/VHS will now

search in super high speed. (in the LP / SLP modes

only)

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

If you press the TV/VCR side PLAY button in the

DVD mode, you can start the VCR playback.

•

If you press the SELECT button in the VCR

playback, it will stop and the mode will

change to the DVD mode. In addition, the

same function operates with the DVD side

PLAY button or OPEN/CLOSE button.

•

TRACKING ADJUSTMENT

STILL PICTURE

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE button

during playback. Only tapes recorded in the SLP

mode will show the least amount of lines.Press the

PLAY button to return to playback.

However when playing pre-recorded tapes or tapes

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

You can reduce the noise lines by pressing the

CHANNEL K or L button in slow mode, too.

Tracking adjustment in Slow mode will not be set

automatically.

NOTE:

In Still mode, press the SLOW button and press the

CHANNEL K or L button until streaks disappear.

To return to Still mode, press the PAUSE button

again.

NOTES:

•

You can advance the picture one frame at a time by

pressing the PAUSE button during the Still mode.

If it is left in the Pause mode for more than five

minutes, the TV/DVD/VHS will automatically

switch to the Stop mode.

•

VERTICAL HOLD CONTROL

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

•

NOTE:

If there are video noise lines on the screen, see Tracking

Adjustment section.

- 26 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

Make sure ...

AUTO REPEAT PLAYBACK

The TV/DVD/VHS has the auto repeat function that

allows you to repeat a tape indefinitely without

touching the PLAY button.

TV/DVD/VHS power must be turned on.

Insert a prerecorded tape.

•

Before playback, follow steps below.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

RENTAL PLAYBACK

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

Press the SETUP button on the

remote control.

Press the SETUP button on the

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

remote control.

Press the Arrow K or L button to

point to “USER’S SET UP”.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the Arrow K or L button to

point to “USER’S SET UP”.

Then, press the Arrow B button.

TIME SEARCH

INDEX SEARCH

Then, press the Arrow B button.

2 Select “ALL” or “BLANK”

Press the Arrow K or L button to

point to “REPEAT PLAY”.

Press the Arrow B or s button

repeatedly until your desired selec-

tion [ALL] or [BLANK] appears.

2 Set “RENTAL” to [ON]

Press the Arrow K or L button to

point to “RENTAL”.

Press the Arrow B or s button

until [ON] appears.

USER’S SET UP

–

USER’S SET UP

–

RENTAL

[ON]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[ALL]

[HIFI]

[OFF]

[STEREO]

[HIFI]

[STEREO]

3 Exit the Rental setting

Press the SETUP button on the remote control to

return to the TV mode.

3 Exit the Repeat Play setting

Press the SETUP button on the remote control to

return to the TV mode.

4 Start playback

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

•

Press the PLAY button to start the Repeat Play.

”REPEAT PLAY B” appears.

•

Once you select the Rental mode, it stays in effect

even after you turn off the TV/DVD/VHS.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/DVD/VHS.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2], select [OFF] using the

Arrow B or s button on the remote control. Press

the SETUP button on the remote control to return to

TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps [1] and [2], select [OFF] using the

Arrow B or s button on the remote control. Press

the SETUP button on the remote control to return to

TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

- 27 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

Make sure ...

TV/DVD/VHS power must be turned on.

Insert a tape.

•

This function will not operate in recording mode.

This function is not operative when a cassette tape

is not inserted in the TV/DVD/VHS.

In the example below: To watch a program after 2

hour 50 minutes from the present position, in either

direction.

•

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

1 Insert a tape.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

2 Select “TIME SEARCH” mode

- TV/VCR SETUP -

Press the SETUP button on the

TIMER PROGRAMMING

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the Arrow K or L button to

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

2 Reset the counter to 0:00:00

Press the C.RESET button repeatedly.

point to “TIME SEARCH”.

TIME SEARCH

INDEX SEARCH

Then, press the Arrow B button.

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

3 Enter your desired time

Press the Arrow K or L button until

your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

TIME SEARCH

2 : 50

If you wish to cancel the Time

Search at this point, press the SETUP button on the

remote control.

4 To activate “ZERO RETURN” mode

- TV/VCR SETUP -

Press the SETUP button on the

TIMER PROGRAMMING

SETTING CLOCK

remote control.

Press the Arrow K or L button to

point to “ZERO RETURN”.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

4 Begin Time Search

By pressing the Arrow s or B button, the

TV/DVD/VHS will rewind or fast forward to the

specified point.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

Then, press the Arrow B button.

The counter will appear on the TV screen.

The tape will automatically stop when the counter

returns to 0:00:00.

TIME SEARCH

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/DVD/VHS

or the remote control. This will delete the selected

time.

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

NOTES:

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

•

- 28 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX SEARCH

This feature provides a method of indexing the start-

ing point so that it can be easily returned to in either

fast forward or rewind mode.

The index mark will be made automatically when

the REC button is pressed. It will also be marked at

the starting point of Timer recording and OTR.

1 Select “INDEX SEARCH”

Press the SETUP button on the

remote control.

Press the Arrow K or L button to

point to “INDEX SEARCH”. Then,

press the Arrow Bbutton.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

•

2 Enter your desired number

Press the Arrow K or L button until

the number of programs that you

want to skip appears.

The index mark will not be recorded if the PAUSE

button is pressed and released during recording.

The time gap between making the index marks on

the tape should be greater than 1 minute for SP

recording, 2 minutes for LP recording and 3 min-

utes for SLP recording.

In some cases, the index mark at the beginning of

video tape cannot be detected.

•

INDEX SEARCH

0 3

•

(Example: “03” for 3 programs)

The Index Search mode will be

canceled if the procedures are not activated in 30

seconds.

•

Example: You are watching program number 4 and

want to fast forward to program number 7. You

must skip three programs.

3 Begin Index Search

Press the Arrow s or B button. The TV/DVD/VHS

begins rewinding or fast forwarding to the beginning

of desired program.

NOTE: Every time an index signal is skipped, the

number in the program indicator decreases by one.

CURRENT PLAYBACK PROGRAM

Beginning of tape

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7

End of tape

4 After Index Search

When the preset program is reached, the

TV/DVD/VHS will start playback automatically.

A video cassette must be inserted in the

TV/DVD/VHS for this function to work.

•

INDEX MARK

The number of Index Searches can be set up to 20.

This function will not operate in the recording mode.

When you want to cancel the Index Search while

in progress, press the STOP button.

•

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.)The “–” indication will appear when the tape has

rewound further than “0:00:00” on the tape counter.

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/DVD/VHS will eject the tape and

turn itself to off.

•

This function is operative when Repeat Play is set

to the [OFF] position.

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

•

- 29 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Make sure ...

TV/DVD/VHS power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTES:

This unit will ONLY record and view the same channel.

This unit cannot record the contents from the built-in DVD.

•

SKIPPING UNWANTED

NORMAL RECORDING

You can ONLY watch the same TV program that is

being recorded.

SCENES DURING RECORDING

Press the PAUSE button to tem-

PAUSE

porarily stop recording.

Press the PAUSE or RECORD but-

ton to resume recording.

NOTES:

1 Select the channel to be recorded

Press the number buttons on the

CH 10

remote control or the CHANNEL

K or L button.

After five minutes, the

TV/DVD/VHS will automatically switch to the

Recording mode to prevent tape damage.

•

Remember: If the TV/DVD/VHS is

connected to a cable box or satellite

box, the TV/DVD/VHS must be on CH3 or CH4,

then the channel to be recorded must be selected on

the cable box or satellite box.

If “CLOSED CAPTION (ON)” is selected, the On-

Screen Display will appear for 5 seconds, then dis-

appear.

•

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

3 Begin recording

Press the RECORD button.

REC

4 Stop recording

Press the STOP button when recording is completed.

- 30 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

Push(es) Display

1 push

Recording length

(normal recording)

OTR (One Touch Recording)

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/DVD/VHS.

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

Make sure ...

17 pushes

8:00

480 minutes

TV/DVD/VHS power must be turned on.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

•

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

tape to the point at which you want to begin

recording.)

You can make copies of video tapes made by friends

or relatives for your enjoyment.

NOTES:

This function CANNOT be done from the remote

control.

•

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Recording starts immediately when the REC/OTR

button is pressed.

•

When the REC/OTR button is pressed 18 times, the

TV/DVD/VHS returns to the Normal Recording

mode.

•

Connect your TV/DVD/VHS and a Source (Playing)

VCR using the following diagram.

To stop the OTR operation, press the STOP button

on the TV/DVD/VHS or on the remote control.

•

[Fig.8]

[The TV/DVD/VHS]

To show the remaining time, press the DISPLAY

•

HEADPHONE VIDEO

L-AUDIO-R

button on the remote control so that “OTR”

appears on the TV screen. (It will show up momen-

tarily then disappear.)

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum record-

ing time, assuming the tape is started at the begin-

ning, is 8 hours using T-160 (or 6 hours using T-

120).

•

[Ex: Source (playing)

VCR or camcorder]

If the tape runs out before the end time, the

TV/DVD/VHS will switch to the Stop mode imme-

diately, ejects the tape and turns itself off.

•

AUDIO

Audio/Video

adapter cable

(not supplied)

OUT

VIDEO

1 Select the channel to be recorded

Press the number buttons on the remote control or

the CHANNEL K or L button.

Remember: If the TV/DVD/VHS is connected to a

cable box or satellite box, the TV/DVD/VHS must be

on CH3 or CH4, then the channel to be recorded is

selected on the cable box or satellite box.

OUT

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record over, into the TV/DVD/VHS’s cassette com-

partment.

3)Press the SPEED button on remote control for the

TV/DVD/VHS to select the desired recording

speed (SP/SLP).

4)Press the CHANNEL K or L button on the

TV/DVD/VHS until “AUX” appears on the screen.

5)Press the RECORD button on the TV/DVD/VHS.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during copying, use the

TV/DVD/VHS’s front panel controls whenever pos-

sible. The remote control might affect the source

(Playing) VCR’s playback operation.

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

OTR(2 : 30)

3 Begin OTR

Press the REC/OTR button on the

TV/DVD/VHS as many times as

needed. The recording length will

be determined by the number of

times you press the REC/OTR button. Each addition-

al push will increase the recording time by 30 min-

utes. It is set up to 8 hours.

- 31 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER

pressing the Arrow K button. And press the Arrow

AUTOMATIC TIMER

RECORDING

You may set the TV/DVD/VHS to start and end a

recording while you are away. You can set 8 pro-

grams to record on specific days, daily or weekly

within a 1 year period.

button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

If you have not yet set the clock,

•

“MANUAL CLOCK SET”

appears. If so, follow stops [3] to

[8] on page 18. Then set the timer

recording.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

In the example below, the timer is being set to record:

DATE:

July 5th, 2002

2 Select your desired program

position (1~8)

Press the Arrow K or L button to

select the desired program position.

Then, press the Arrow B button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL:

TAPE SPEED:

- - -/- - - - - -:- -

-:- - - -

CH61

Make sure ...

If a cable box or satellite box is connected with the

TV/DVD/VHS you will be limited to record only

one channel. And the channel selector on the

TV/DVD/VHS must be selected to the output

channel of the boxes CH 3 or CH 4 and then the

actual channel to be recorded must be selected on

the boxes.

Clock must be set to the correct time and date

before setting the timer.

TV/DVD/VHS power must be turn on to program

it.

•

3 Set the channel number

Press the Arrow K or L button until

the desired channel number

appears.

(Example: CH61)

Then, press the Arrow B button.

Remember: If the TV/DVD/VHS is connected to a

cable box or satellite box, the TV/DVD/VHS must be

on CH3 or CH4, then the channel to be recorded is

selected on the cable box or satellite box.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

•

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

The channel you want to record is properly set in

advance. (See page 16.)

•

4 Select once, every day or

weekly recording

For once recording :

– TIMER PROGRAMMING –

CH DATE

BEGIN END

- - -/- - - - - -:- -

61 7/05 FRI -:- -

- - -/- - - - - -:- -

-:- - - -

Avoid over lap of programs ...

There is a chance that a program will not be record-

ed. when programs overlap;

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

Press the Arrow K (up) button

until the desired date appears.

(Example: “7/05” for July 5th). Then, press the

Arrow B button.

•

programs will begin recording in sequence.

The illustration below demonstrates the sequence

of recordings.

For every day recording : To record a TV program

•

at the same time on the same chan-

nel every day. (Example: Monday

through Sunday)

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

Press the Arrow L (down) button ^B

until “EVRY DAY” appears.

Recording Sequence

Then, press the Arrow B button.

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

For weekly recording : To record a TV program at

the same time on the same channel

every week. (Example: every

Monday)

Press the Arrow L (down) button

until “EVRY” and your desired

9:00AM

10:00AM

11:00AM

12:00PM

– TIMER PROGRAMMING –

*Recording period is SHADED

CH DATE

BEGIN END

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

1 Select “TIMER PROGRAMMING”

Press the SETUP button on the remote control.

Confirm “TIMER PROGRAMMING” is pointed by

day of the week appear together. Then, press the

Arrow B button.

- 32 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

– TIMER PROGRAMMING –

CH DATE BEGIN END

TIMER PROGRAM EXTENSION

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

2)Repeat step [1] on page 32.

5 Set beginning hour

- - -/- - - - - -:- -

-:- - - -

Press the Arrow K or L button until

the desired hour appears.

61 7/05 FRI 7:12^P

- - -/- - - - - -:- -

(Example: “ 7, PM” for 7:30PM)

Then, press the Arrow B button.

3)Press the RECORD button and select the desired

program using the Arrow K or L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the PAUSE but-

ton on the remote control. The recording time

returns to the original time.

– TIMER PROGRAMMING –

CH DATE BEGIN END

6 Set beginning minute

Press the Arrow K or L button until

the desired minute appears.

- - -/- - - - - -:- -

-:- - - -

61 7/05 FRI 7:30^P

- - -/- - - - - -:- -

(Example: “30” for 7:30PM)

Then, press the Arrow B button.

7 Set end hour

Press the Arrow K or L button until

the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the Arrow B button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

61 7/05 FRI 7:30^P

8:30^P

- -

- - -/- - - - - -:- -

-:- - - -

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

5)Press the Arrow B or s button to exit the setting

menu. Then press the SETUP button on the remote

control to return to original mode.

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

Press the Arrow K or L button

until the desired minute appears.

(Example: “50” for 8:50PM)

Then, press the Arrow B button.

- - -/- - - - - -:- -

-:- - - -

61 7/05 FRI 7:30^P

8:50^P

- -

- - -/- - - - - -:- -

-:- - - -

TO CORRECT A PROGRAM

While setting a program; press the Arrow s but-

ton to go back one step and enter the correct num-

•

9 Set the tape speed

Press the Arrow K or L button

until the desired tape speed

appears. (Example: SP)

– TIMER PROGRAMMING –

CH DATE BEGIN END

bers using the Arrow K or L button.

After setting a program;

1)Press the POWER button.

- - -/- - - - - -:- -

-:- - - -

•

61 7/05 FRI 7:30^P

8:50^P

- - -/- - - - - -:- -

-:- - - -

2)Repeat steps [1] - [2] on page 32.

3)Press the Arrow B button (or press the Arrow

button to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the Arrow K or L button.

4)Press the POWER button to set automatic timer

recording.

10 Finish setting the program

Press the Arrow B or s button. The program is now

completed.

To set another program, repeat steps [2] to [10].

Press the SETUP button on the remote control to

return to original mode.

•

TO CANCEL AN AUTOMATIC TIMER

RECORDING

After setting a program;

1)Press the POWER button.

2)Repeat steps [1] ~ [2] on page 32 and select a

program you want to cancel.

3)Press the C.RESET button.

4)Press the SETUP button on the remote control to

return to TV mode.

11 Set the timer

Press the POWER button to set automatic timer

recording. The TIMER REC indicator lights up.

•

You must turn off the TV/DVD/VHS to activate

automatic timer recording.

•

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

While recording is in progress;

•

1)Press POWER button.

2)Press the STOP/EJECT button on the

TV/DVD/VHS.

- 33 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

2)Press the SETUP button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the Arrow B button. The details of programs

appear on the TV screen.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/DVD/VHS will rewind to the beginning of the

recorded program(s).

NOTE:

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

•

5)Press the SETUP button on the remote control to

return to TV mode.

4 Watch the recorded program

Press the PLAY button.

HINTS FOR AUTOMATIC

TIMER RECORDING

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

Arrow B or s button.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

Make sure the channel you want to record is prop-

erly set in advance.

It is not necessary to press the RECORD button for

timer recording.

•

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

•

SLEEP TIMER

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

•

The Sleep Timer function turns off the

TV/DVD/VHS without using the POWER button

after a desired period of time.

NOTE:

If the tape runs out before the end time, the

TV/DVD/VHS will switch to the Stop mode imme-

diately, and the tape will be ejected.

•

This function does not operate during Recording

mode.

•

1 Select “SLEEP TIMER”

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears.

2 Set sleep time

Press the SLEEP button until your

desired sleep time appears.

Each additional push will increase

the time by 30 minutes up to 120

minutes.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

Press the SETUP button on the

SETTING CLOCK

CHANNEL SET UP

remote control.

Press the Arrow K or L button to

point to “USER’S SET UP”.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

SLEEP 120 MINUTES

After 5 seconds, exit the Sleep

Timer setting.

INDEX SEARCH

Then, press the Arrow B button.

TO CANCEL THE SLEEP TIMER

2 Set “AUTO RETURN” to [ON]

Press the Arrow K or L button to

point to “AUTO RETURN”.

Press the Arrow B or s button

until [ON] appears.

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears. Press the SLEEP button

until “SLEEP 0 MINUTES” appears.

USER’S SET UP

–

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[ON]

[HIFI]

[STEREO]

- 34 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

When the Closed Caption mode is OFF:

When the Closed Caption mode is ON:

Counter mode: After 5 seconds, only the counter

remains. To clear it, press the DISPLAY button.

Clock mode: After 5 seconds, only the clock and

the channel number remain. To clear them, press

the DISPLAY button.

The On Screen Display disappear after 5 seconds.

This is true even if the MUTE button is pressed, or

the PAUSE button is pressed while recording.

•

OFF mode

Clock/Counter mode

OFF mode Counter mode

Clock mode

STOP

5:40PM

CH2

STOP

5:40 PM

CH2

COUNT 0:12:34

After 5 seconds

5:40PM

CH2

COUNT 0:12:34

Counter

remains

Clock & Channel

remains

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 35 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD SECTION

ABOUT THE DISCS

Photo CD

PLAYABLE DISCS

(Never play back, otherwise malfunction may

result.)

The following discs can be played back on this DVD

Video CD

player.

(Never play back, otherwise malfunction may

result.)

Maximum

Playback Time

Disc Type

Logo

Contents Disc Size

Any other discs without compatibility indications

Approx. 4 h

(single-sided)

Approx. 8 h

12 cm

Sound

and

Pictures

(double-sided)

DVD

Video

DISC TYPES

Approx. 80 min

(single-sided)

Approx. 160 min

(double-sided)

[

]

DVD

8 cm

Data on a DVD is divided into sections called "titles", and

then into subsections called "chapters", each of which is

given a title or chapter number. Playback conditions are

preset on some DVD video discs, and these playback con-

ditions take priority over user operations on this player. If

a function you selected do not run as desired, refer to the

manual accompanying the disc.

12 cm

74 min

Audio

Sound

8 cm

20 min

(singles)

This player conforms to the NTSC color system. You can-

not play discs recorded in other color systems such as

PAL or SECAM.

Example

¡Some discs include region codes as shown below.

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

¡The number inside the symbol refers to a region of the

world, and a disc encoded in a specific region format

can only be played back on DVD players with the same

region code.

[

]

AUDIO CD

Data on an audio CD is divided into sections called

“tracks”, each of which is given a track number.

The following discs cannot be played back on this

DVD player.

Example

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

DVD with region codes other than 1 or ALL.

DVD-ROM

DVD-RAM (Never play back, otherwise mal-

function may result.)

CD-ROM

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-R

(Never play back, otherwise malfunction may

result.)

CD-I

(Never play back, otherwise malfunction may

result.)

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

PLAYING A DISC

¡If a disc is dirty or has scratches, the pictures may

PLAYING A DVD VIDEO

OR AN AUDIO CD

appear distorted and the playback operation may

stop. In such cases, clean the disc and unplug the

power cord and then plug it again before resuming

playback.

DVD

¡With DVDs that use some titles for playback

program signals, playback may start from the second

title, or it may skip these titles.

Getting started

Turn on the power of the TV, amplifier and any other

components which are connected to the DVD player.

(Change the input system to suit the DVD player, and

check that the sound volume is correct.)

USING THE DVD MENUS

DVD

Press the POWER button.

¡The power will turn on.

Some DVDs contain their own menus, such as a

guidance menu which describes the contents of the

disc or a selection menu for sound, language and other

customized settings.

Press the OPEN/CLOSE button.

¡The disc loading tray will open.

Place a disc into the tray.

Press the DISC MENU button.

¡Make sure the disc is sitting properly in the correct

recess, with the label side up.

¡The DVD menu will appear.

Select the desired title.

¡Press the arrow buttons (L/K/B/s) to change the

setting, and then press the ENTER button.

Playback will start from the selected title.

USING THE TITLE MENU

Press the PLAY button.

DVD

¡The tray will close automatically, and playback will

then start from the first chapter or track of the disc.

You need to press the PLAY button only when the

tray has been closed by pressing the OPEN/CLOSE

button.

With a DVD containing a title menu, you can select

desired titles from the menu.

Press the TITLE button.

¡When you play back the DVD which a title menu is

recorded, the menu may appear on the screen. In this

case, refer to “USING THE TITLE MENU”.

¡The title menu will appear.

Select the desired title.

¡Press the arrow buttons (L/K/B/s) to change the

setting, and then press the ENTER button.

Press the STOP button to stop play.

Notes

¡If you press the OPEN/CLOSE button in the CALLING UP A MENU SCREEN

TV/VCR mode or power-off, the DVD tray will DURING PLAYBACK

open.

For DVDs

¡If you press the DVD side PLAY button in the

TV/VCR mode or power off, you can start the DVD

playback.

¡Press the DISC MENU button to call up the DVD

menu.

¡A “prohibited icon” may appear at

the top-right on the TV screen

during operation, warning that a

prohibited operation has been

encountered by the DVD player

or the disc.

¡Press the TITLE button to call up the title menu.

Note

¡Contents of menus and corresponding menu

operations may vary between discs. Refer to the

manual accompanying the disc for details.

–

_{Download from Www.Somanuals.co}3_m7_{. All Manuals Search And Download.}

01A11

Press the PLAY button to return to normal

playback speed.

RESUMING PLAYBACK FROM

THE POINT WHERE

PLAYBACK STOPPED

DVD

Press the STOP button during playback.

PAUSING PLAYBACK OR

DISPLAYING A STILL PICTURE

¡Playback will stop, and then

appear the resuming message at

the center.

Press 'PLAY' to play from here

To play beginning, press 'STOP' first

and the 'PLAY'.

DVD

Press the PAUSE button during playback.

¡Playback will pause, with sound

muted.

Pause F

Press the PLAY button. Playback will start

from the point where the previous playback

session was stopped.

Play B

Press the PLAY button to resume playback.

Notes

¡Resuming playback is not available with some discs.

Play B

¡It is possible to switch from the DVD play mode to

the TV mode. Even if the power is turned off, the

resume function enables to playback on from the

previously interrupted point. But note that the

Marker commands are not saved.

STEPPING THROUGH FRAMES

¡The resume function can be reset by pressing the

STOP button twice or by opening the disc loading

tray.

DVD

Press the PAUSE button while playback is

paused.

FAST FORWARD/REVERSE

Pause F

¡The next picture frame is dis-

played with sound muted each

time the button is pressed.

DVD

Press and hold the g or h button for

more than 1 second during playback.

¡For DVDs, pressing and more than 1 second holding

the g or h button cycles the playback speed in

three steps.

Press the PLAY button to resume playback.

Play B

¡For audio CDs, the playback speed is ×16 fixed.

REV

Button

Ex2

FWD D

Button

Dx2

Ex8

Dx8

Ex32

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

STARTING FROM A DESIRED

TIME COUNT

SLOW MOTION

DVD

Press and hold the g button for more than

1 second while playback is paused. (Sound

remains muted.)

Press the SEARCH MODE button.

Time _:__:__

Total Time 1:29:00

¡Press the button twice.

¡Slow motion mode will be activated.

¡Pressing and holding the g button for more than

1 second cycles the playback speed in three steps.

Select an appropriate speed while referring to the

speed indication on the screen.

Press the numeric buttons to set the desired

time count.

Time _:__:__

×1/16

×1/8

×1/2

Total Time 1:29:00

¡Example: 1 hour, 23 minutes and

30 seconds

1 → 2 → 3 → 3 → 0

D Button

Notes

¡In the case of DVD, Time Search in Title is effec-

tive. (But Time Search in Chapter is ineffective.)

Press the PLAY button to return to normal

playback speed.

¡In the case of CD, Time Search in Track is effective.

Notes

(But Time Search in the entire disc is ineffective.)

¡Slow playback is not available with audio CDs.

¡Playback from a desired time count is not available

with some discs.

¡The reverse of slow playback is not available.

¡Specific time playback is not available with some

discs or if the unit is in stop mode.

¡If you press the g button and release immediate-

ly during playback is paused or slow, it returns to

normal playback.

PLAYING FROM A DESIRED

TITLE OR CHAPTER

STARTING FROM A DESIRED

TRACK

DVD

Press the SEARCH MODE button.

You can also press the SEARCH MODE button, use

the numeric buttons to enter the chapter number.

Use the numeric buttons to enter

the track number. When the track

number is entered in the entry box,

playback of the desired track will

start automatically.

Track: __ / 26

Perform the title search and the

chapter search after setting them on

the same screen at the same time.

Changeover by K/L buttons.

Title 1 / 4

Chapter:__ / 17

TRICKS WITH THE SKIP BUTTONS (H, G)

If the SKIP button G is pressed during playback or

while playback is paused, the current track is

skipped and the next track is played. When the SKIP

button H is pressed once, the top of the current

track is located for replaying. When the SKIP button

H is pressed again while Within 2-second

playback, the previous track is located.

Note

Title 1 / 4

Chapter:__ / 17

¡Playback from a desired title or

chapter is not available with some

DVDs.

–

_{Download from Www.Somanuals.co}3_m9_{. All Manuals Search And Download.}

01A11

REPEAT

A-B REPEAT

DVD

Press the REPEAT button.

You can define a section to be played back repeatedly.

For DVDs

Press the A-B REPEAT button during playback.

¡A single title or chapter is played back repeatedly.

¡The starting point (A) will then be

selected.

Repeat

[ A -

]

¡Pressing the REPEAT button cycles the display on

the screen as follows.

Repeat

[Title]

The current Title is

played back repeatedly.

Repeat

[Chapter]

The current Chapter is

played back repeatedly.

Press the A-B REPEAT button again at the

end point (B) of the desired section.

Repeat

[Off]

No repeat playback.

¡The selected section will be

Repeat

[ A - B ]

played back repeatedly.

For audio CDs

¡The whole disc or a single track is played back

repeatedly.

To exit A-B repeat playback, press the A-B

REPEAT button and set it to OFF.

¡Pressing the REPEAT button cycles the display on

the screen through All, Repeat Track and Off.

Repeat

[ off ]

Repeat

[All]

The whole Disc is

played back repeatedly.

Repeat

[Track]

The current Track is

played back repeatedly.

Notes

¡With DVDs, the A-B repeat section can be set only

within the current title.

Repeat

[Off]

No repeat playback.

¡With audio CDs, the A-B repeat section can be set

within the current track.

¡A-B repeat is not available with some scenes in

DVD.

If the REPEAT button is pressed once dur-

ing program/random playback, the pro-

gram/random playback is performed

repeatedly.

¡To cancel the A point which was set, press RETURN

button.

If the REPEAT button is pressed again, the

current track is played back repeatedly.

Notes

¡Repeat playback is not available with some discs.

¡The REPEAT setting will be cleared when moving

to other title, chapter or track.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

PROGRAM (Audio CD)

RANDOM (Audio CD)

Press the MODE button in stop mode.

Audio CD

¡The program setting menu screen will appear.

¡The program screen will appear.

Program

Total

[Track]

– –

Press the MODE button again.

[Time]

0:00:00

Track

00 15

Start

Random

PLAY Delete

MODE Exit

CLEAR

RETURN

Audio CD

Random

Start

PLAY Exit

MODE

Press the numeric buttons to enter the

desired track numbers.

Audio CD

Program

02 05 07 14 01 09 13 10 03 11

08 04

¡The total playback time for the

selected tracks will appear on the

TOTAL line.

Total

[Track]

Press the PLAY button. Random playback

will then start.

[Time]

0:47:29

Track

04 / 15

Start

Random

PLAY Delete

MODE Exit

CLEAR

RETURN

Note

¡Program playback is not available during random

playback.

Press the PLAY button.

¡Playback will start in the programmed order.

ZOOM PLAYBACK

¡While the program is being played back, the STOP

button works as follows.

(enlargement onscreen)

¡Press the STOP button once and then the PLAY

button again, playback will restart from the point

where the STOP button was pressed. (Program

continued)

DVD

Images can be enlarged four times on the screen to

your taste.

¡Press the STOP button twice and then the PLAY

button again, playback will restart from the first tune

in the program in the usual way. (Program

continued)

Press the ZOOM button during playback.

¡An image will be enlarged at the center of the

screen.

¡Press the STOP button three times and then the

PLAY button again, playback will restart from the

track in the usual way. (Program cleared)

¡Press the ZOOM button again, and the image will be

back to the previous size.

Zoom [on]

Notes

¡Adding programs is not possible during program

playback. You must stop the current playback before

such operations can be carried out.

¡Press the CLEAR button to cancel a program. The

most recently entered program will then be deleted.

¡Numbers which exceed the number of tracks on the

disc in the tray are not accepted.

When the cursor (K/L/s / B) button is pressed

during zoom play, the part to be zoomed moves.

¡Playback from a desired track and random playback

are not available during program playback.

¡The zooming frame can be moved from the center

.... 4 steps to the right. 4 steps to the left. 4 steps to

the top. 4 steps to the bottom.

¡Program settings are cleared when the power is

turned off or the disc loading tray is opened.

¡If the track no. is once set in the program, the setting

cannot be changed.

–

_{Download from Www.Somanuals.co}4_m1_{. All Manuals Search And Download.}

01A11

Note

¡Zooming function does not work while operation

display screen is shown.

SETTINGS

Notes

CHANGING THE AUDIO

¡Pressing the Audio button may not work on some

DVDs with multiple audio languages (e.g. DVDs

which allow audio language setting on the disc

menu). Operation varies between discs, so refer to

the manual accompanying the disc.

LANGUAGE OR SOUND MODE

DVD

The DVD player has a function which allows you to

select the desired audio language and sound mode.

¡If a desired language is not shown after pressing the

Audio button several times, the disc does not have

an audio source in that language.

For DVDs

Press the AUDIO button during playback, and then

press the AUDIO button to select the desired audio

language.

¡The audio language resets to the one which has been

selected in the setup mode, every time the power is

turned on or discs are replaced. If that language is

not available on a disc, a language defined by the

disc is selected.

¡The audio language can be changed if multiple

languages are recorded on the DVD being played.

¡The screen display will disappear after about 5

Audio 1 , English/8

seconds.

Audio 2 , French/8

Audio 8 , Japanese/8

Bonjour

HELLO

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

CHANGING THE SUBTITLE

LANGUAGE

CHANGING THE CAMERA

ANGLE (Multi-Angle Pictures)

DVD

The DVD player has a function which allows you to The DVD player has a function which allows you to

select the desired language for subtitles.

select the desired camera angle.

Press the SUBTITLE button during playback, and

then press the SUBTITLE button to select the

desired subtitle language.

Press the ANGLE button during playback.

¡If the disc contains sequences recorded from differ-

ent camera angles, the angle icon ( ) will appear

¡The subtitle language can be changed if the subtitles

are recorded in multiple languages on the DVD

being played.

at the top-right of the screen. You can change the

camera angle when the icon appears on the screen.

¡The camera angle cannot be changed if the disc does

not contain sequences recorded from different

camera angles.

¡The subtitle language cannot be changed if the

subtitles are recorded in a single language on the

DVD being played.

Subtitle 1 , English/8

Subtitle 1

Press the ANGLE button while the angle

number is shown on the screen.

Subtitle 2 , French/8

Subtitle 2

Angle 1 / 8

Angle 1

Angle 2 / 8

Subtitle Off

Angle 2

No subtitles

Angle 8 / 8

Angle 8

Bonjour

HELLO

Note

¡The screen display will disappear after about 5

seconds.

¡Pressing the SUBTITLE button cycles the subtitle

language from SUBTITLE 1, SUBTITLE 2 and all

the languages recorded through to off.

Notes

¡Some discs allow subtitle language setting on the

disc menu. (Operation varies between discs, so refer

to the manual accompanying the disc.)

¡If the desired language is not shown after pressing

the SUBTITLE button several times, the disc does

not have subtitles in that language.

¡The subtitle language resets to the one which has

been selected in the setup mode, every time the

power is turned on or discs are replaced. If that

language is not available on a disc, a language

defined by the disc is selected.

¡It may take time to display the subtitles in the

selected language.

¡The screen display will disappear after about 5

seconds.

¡When “Subtitle Not Available” appears onscreen, it

means no subtitle is recorded on the scene.

–

_{Download from Www.Somanuals.co}4_m3_{. All Manuals Search And Download.}

01A11

CHANGING THE ON-SCREEN

DISPLAY

For DVDs

Kind of disc in playbacking

DVD

Play

Picture in play back

Current playback status

Current repeat status

Current title number

Current chapter number

Repeat

[Chapter]

DVD

Title

Chapter

Time

0:17:52

-1:38:46

Bit Rate

• Chapter

Title

18 / 30

You can check the information about the disc by

pressing the DISPLAY button on the remote control.

1 /

Time

Audio

1:56:38

Elapsed time of the current title and

Remaining time of the current title.

1.English / 4

Info. Window

For audio CDs and DVDs

Playback Setup Window

Playback Setup Window (DVD)

Press the DISPLAY button, the display appears on the

screen.

ITEM

Chapter

DISPLAY CONTENTS

Current chapter number / the number of

total chapters

Current title number / the number of total

titles

Title

For the selecting the item of the Playback Setup

Window, press the K L

then press the ENTER button.

Time

Audio

Total time of the current title

button to select the item,

Audio No., audio language / the number

of available audio languages in the disc

Subtitle No., subtitle language / the

number of available subtitle languages in

the disc

Subtitle

Angle

For audio CDs

Off : Subtitle is not displays.

Not Available : Subtitle is not included.

Kind of disc in playbacking

Current playback status

Current repeat status

Current track number

Nomal playback

Audio CD

Play

01 02 03 04 05 06 07 08 09 10

11 12

Repeat

[Track]

Angle No. / total number of the angles

1/1 : Multi angle is not included in the

disc.

Track

Play Mode

Normal

Track

2 / 12

0:05:13

...

Programedplayback

Random playback

Time

[Track]

0:01:46

-0:03:27

Place the cursor and press the ENTER

button to activate the Marker function.

[Set the marker]

Maker

Time Display Track

[Track]

Elapsed time of the current track and

Remaining time of the current track.

[All]

Elapsed time of the current disc and

Remaining time of the current disc.

Info. Window

Playback Setup Window

K L

button, position the cursor on

Using

to the marker number shown as “Not

Set”. Press the ENTER button when the

screen to be reviewed appears.

Up to 5 points can be marked.

Playback Setup Window (CD)

[Call back the marker]

Marker

K L

button, position the cursor on

ITEM

Track

DISPLAY CONTENTS

Using

to the marker number to be called back

and press the ENTER button.

Current track number / the number of

total tracks

[Clear the marker]

Time

Total time of the current track

K L

button, position the cursor on

Using

to the marker number to be cleared and

press the CLEAR button.

Place the cursor and press the ENTER

button to activate the Marker function.

To clear all markers, place the cursor on

“All Clear Markers” and press the

ENTER button.

[Set the marker]

K L

button, position the cursor on

Using

to the marker number shown as “Not

Set”. Press the ENTER button when the

screen to be reviewed appears.

SRS

TruSurround

The current setting (On/Off) is displayed.

Up to 5 points can be marked.

[Call back the marker]

Marker

K L

button, position the cursor on

Using

To exit the display (DVD and CD):

Press the RETURN button.

to the marker number to be called back

and press the ENTER button.

[Clear the marker]

In the playback Setup Window, press the RETURN button to

change the present indication to the former one.

K L

button, position the cursor on

Using

to the marker number to be cleared and

press the CLEAR button.

To clear all markers, place the cursor on

“All Clear Markers” and press the

ENTER button.

The time informations displays on the left

side of the screen (Track/All)

Time Display

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

CHANGING THE SETUP ITEMS

Note

(The on-screen display appears in selected language.)

¡When you change the setup items, press the STOP

button if you are in playback mode.

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

Language

Display

Audio

LANGUAGE SETTINGS

Player Menu

English

Français

Español

Press the SETUP button.

Language

Display

Audio

¡The setup screen appears.

Press the K/L buttons to select a desired item,

and then press the ENTER button.

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

¡If Other is selected on the Audio, Subtitle or Disc

Menu setting screen, the Language Code setting

screen will appear. Press the numeric buttons to

enter the desired language code while referring to

the list on page 49.

Press the K/L buttons to select Language,

and then press the ENTER button.

Language Controls

Audio

English

Audio

Subtitle

Disc Menu

Player Menu

English

Subtitle

Language

Display

Audio

Disc Menu

Player Menu

Display

Audio

Irish

Portuguese

Dutch

Other

.......

Parental

Press the K/L buttons to select an item, and

then press the ENTER button.

Press the SETUP button.

(Voice is played back in selected language.)

¡The setup mode will be canceled and the ordinary

screen will appear.

Language Controls

Audio

English

Subtitle

Language

Display

Audio

Disc Menu

Player Menu

Note

Audio

Original

English

French

Spanish

¡Language Setting for Audio and Subtitle is not avail-

able with some discs. Then use the Audio and

Subtitle button. Details are on pages 42 and 43.

(Subtitles are shown in selected language.)

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

Language

Display

Audio

Subtitle

Off

English

Spanish

French

(The disc menu appears in selected language.)

Language Controls

Audio

Subtitle

Disc Menu

Player Menu

English

Language

Display

Audio

Disc Menus

Original

English

French

Spanish

–

_{Download from Www.Somanuals.co}4_m5_{. All Manuals Search And Download.}

01A11

Background Color (Default : Gray)

Select gray or blue.

DISPLAY SETTINGS

Display Controls

Press the SETUP button.

On Screen Info

Angle Icon

Background Color Gray

Auto Power Off On

Language

Display

Language

¡The setup screen will appear.

Display

Audio

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

Auto Power Off (Default : On)

Set or not set to turn off after the screen saver is started and

no keys are pressed for 30 minutes.

Display Controls

On Screen Info

Angle Icon

Background Color Gray

Auto Power Off On

Press the K/L buttons to select Display and

then press the ENTER button.

Language

Display

Display Controls

TV Aspect

On Screen Info On

Angle Icon On

Background Color Gray

4:3 Pan & Scan

Language

Display

Press the K/L buttons to select a desired item,

and then press the ENTER button.

Press the K/L buttons to select an item, and

then press the ENTER button.

Press the SETUP button.

¡The setup mode will be canceled and the ordinary

screen will appear.

TV Aspect

(Default : 4:3 Pan & Scan)

4:3 Pan & Scan : Full height picture, trimmed both sides

4:3 Letter Box : Wide screen with black bars on top and

bottom

Display Controls

TV Aspect

On Screen Info On

Angle Icon On

4:3 Pan & Scan

Language

Display

Audio

Background Color Gray

TV Aspect

4:3 Pan & Scan

4:3 Letterbox

Notes

• Some discs do not contain pan and scan images.

• Some discs do not contain letter box images.

On Screen Info (Default : On)

Display or not display the disc status (Example “PLAYB”).

Display Controls

TV Aspect

On Screen Info On

Angle Icon On

Background Color Gray

4:3 Pan & Scan

Language

Display

Angle Icon (Default : On)

Display or not display the Angle icon on the screen.

Display Controls

TV Aspect

On Screen Info On

Angle Icon On

Background Color Gray

4:3 Pan & Scan

Language

Display

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

Dolby Surround: When the unit is connected to an

audio component that conforms to

Dolby Surround Pro Logic

Stereo: When the unit is connected to a normal audio

component

Down Sampling (Default : 48kHz)

Set the output for the DVD recorded in PCM 96kHz

AUDIO SETTINGS

Press the SETUP button.

Language

Display

¡The setup screen will appear.

Audio

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

(96kHz or 48kHz)

To select Down

Sampling 48kHz or

96kHz, press the

ENTER button

repeatedly.

Press the K/L buttons to select Audio and

then press the ENTER button.

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Language

Display

Audio Controls

Digital Audio Out

Dynamic Range On

...

Language

Display

Downmix Mode Dolby Surround

Down Sampling 48kHz

Press the K/L buttons to select a desired item,

and then press the ENTER button.

¡If PCM, Dolby Digital or DTS MPEG is selected on

the Digital Audio Out setting screen, press the K/L

buttons again to select a further item, and then press

the ENTER button.

Press the K/L buttons to select an item, and

then press the ENTER button. (Choose

Digital Audio Out and press the ENTER but-

ton to set Dolby Digital, DTS, and MPEG. Go

to step 4.)

Dolby Digital (Default : Off)

On : Output by Dolby Digital.

Set to On when the unit is connected to Dolby Digital

Decoder.

Digital audio out setting (Next step)

If you select Digital

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Audio Out, the screen

changes to step 4. If

you want to set other

items of step 3, press

Language

Display

Audio

Audio Controls

Digital Audio Out

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

To select Dolby

...

Language

Display

Audio

Digital On or Off,

press the ENTER but-

ton repeatedly.

Digital Audio Out

Dolby Digital Off

DTS

MPEG

Off

Digital Audio Out

Dolby Digital On

the K/L buttons.

DTS

Off

Dynamic Range (Default : Off)

On : Dynamic range is available

DTS (Default : Off)

On : Output DTS sound

Set to On when the unit is connected to DTS

Decoder.

To select Dynamic

Range On or Off,

press the ENTER

button repeatedly.

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Language

Display

Audio Controls

Digital Audio Out ...

To select DTS On or

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Language

Display

Audio

Off, press the

ENTER button

repeatedly.

¡This function is for controlling the range of sound

volume. By compressing the range of sound vol-

ume, it is possible not only to suppress the output of

loud sound at night and but also to raise the volume

of low sound.

Digital Audio Out

Dolby Digital Off

DTS

MPEG

Off

MPEG (Default : Off)

¡However, this function is effective only for the

sound recorded by Dolby Digital recording. When

the sound recorded by Dolby Digital 5.1ch is out-

putted, the sound is compressed automatically even

with this function being set at “Off”.

On : Output by MPEG

Off : Convert the MPEG to PCM

Audio Controls

To select MPEG On

or Off, press the

ENTER button

repeatedly.

Digital Audio Out

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

...

Language

Display

Audio

Digital Audio Out

Dolby Digital Off

Downmix Mode

(Default: Dolby Surround)

DTS

MPEG

Off

Set to On when the unit is connected to MPEG2

Decoder.

To select Downmix

Mode Stereo or

Dolby Surround,

press the ENTER

button repeatedly.

Audio Controls

Digital Audio Out ...

Dynamic Range On

Downmix Mode Dolby Surround

Down Sampling 48kHz

Language

Display

Press the SETUP button.

¡The setup mode will be canceled and the ordinary

screen will appear.

–

_{Download from Www.Somanuals.co}4_m7_{. All Manuals Search And Download.}

01A11

PARENTAL LOCK

Press the RETURN button.

¡The setup screen will appear.

Press the SETUP button.

Language

¡The setup screen will appear.

Display

Audio

Parental

Select

Set : ENTER

Exit : SETUP

Cancel :

CONTROL LEVELS

Level 8

Press the K/L buttons to select Parental,

and then press the ENTER button.

DVD software of any grade (adult/general/children)

can be played back.

Display

Password

Enter current password...

Levels 7 to 2

Audio

Only DVD software intended for general use and

children can be played back.

_ _ _ _

Parental

Select

Set : ENTER

Cancel :

Exit : SETUP

Level 1

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

Press the numeric buttons to enter the 4-

digit password, and then press the ENTER

button.

¡When doing this for the first time, enter any 4 digits.

That number will be used as the password from the

second time onward.

Notes

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

¡By entering the password, you can then change the

control level and password settings.

Parental Contorols

¡Record the password in case you forget it.

Parental Level

Change

7[NC-17]

Language

Display

IF YOU FORGET THE PASSWORD

1) Open the tray.

2) Press the 1, 2, 3, 4, then DISPLAY button on the

remote control. the default setup screen will appear.

Then, press the ENTER button.

Press the K/L buttons to select an item, and

then press the ENTER button.

When Parental Level is selected

¡Press the K/L buttons to select an item from 8 to 1

and then press the ENTER button.

3) Disconnect the power once and reconnect, then

proceed the step 1 to 4 of the PARENTAL LOCK

again.

Note: If you proceed the above steps, ALL the

settings of the DVD player will be cleared. To use

the DVD player under the previous settings, set

each setting item all over again.

¡When Change is selected, press the numeric buttons

to enter the four digits password. Then press the

ENTER button.

Parental Contorols

Parental Level

Change

7[NC-17]

Language

Display

Audio

Parental Level

4 [PG-13]

3 [PG]

Parental Contorols

Parental Level

Change

7[NC-17]

Language

Display

Audio

Password

Enter current password

_ _ _ _

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

LANGUAGE CODE LIST

No.

Language

Country code

No.

Language

Country code

Afar

4747

4748

4752

4759

4764

4765

4771

4772

4847

4851

4853

4854

4855

4860

4861

4864

4947

4961

4965

4971

5047

5051

5072

5158

5160

5161

5165

5166

5167

5247

5255

5256

5261

5264

5271

5347

5350

5358

5360

5367

5447

5455

5464

5467

5471

5547

5551

5557

5560

5565

5566

5569

5647

5655

5669

5747

5757

5758

5759

5760

5761

5765

5767

5771

5847

5860

5861

5866

Latvian;Lettish

Malagasy

Maori

5868

5953

5955

5957

5958

5960

5961

5964

5965

5966

5971

6047

6051

6058

6061

6149

6159

6164

6247

6258

6265

6266

6367

6459

6460

6461

6467

6469

6547

6550

6553

6554

6555

6557

6558

6559

6560

6561

6563

6564

6565

6566

6567

6568

6569

6647

6652

6653

6654

6655

6657

6658

6660

6661

6664

6665

6666

6669

6757

6764

6772

6855

6861

6961

7054

7161

7254

7267

Abkhazian

Afrikaans

Amharic

Arabic

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Assamese

Aymara

Azerbaijani

Bashkir

Malay

Byelorussian

Bulgarian

Bihari

Maltese

Burmese

Nauru

Bislama

Nepali

Bengali;Bangla

Tibetan

Breton

Dutch (DUT)

Norwegian

Occitan

Catalan

(Afan)Oromo

Oriya

Panjabi

Corsican

Czech

Welsh

Polish

Danish

Pashto;Pushto

Portuguese

Quechua

Rhaeto-Romance

Kirundi

German (GER)

Bhutani

Greek

English (ENG)

Esperanto

Spanish (SPA)

Estonian

Basque

Romanian

Russian

Kinyarwanda

Sanskrit

Sindhi

Persian

Finnish

Sangho

Fiji

100 Serbo-Croatian

101 Singhalese

102 Slovak

103 Slovenian

104 Samoan

105 Shona

106 Somali

107 Albanian

108 Serbian

109 Siswat

110 Sesotho

111 Sundanese

112 Swedish

113 Swahili

114 Tamil

Faroese

French (FRE)

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Hindi

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

115 Telugu

116 Tajik

117 Thai

Indonesian

Icelandic

Italian (ITA)

Hebrew

Japanese (JPN)

Yiddish

Javanese

Georgian

Kazakh

118 Tigrinya

119 Turkmen

120 Tagalog

121 Setswana

122 Tonga

123 Turkish

124 Tsonga

125 Tatar

Greenlandic

Cambodian

Kannada

Korean (KOR)

Kashmiri

Kurdish

126 Twi

127 Ukrainian

128 Urdu

129 Uzbek

130 Vietnamese

131 Volapuk

132 Wolof

Kirghiz

Latin

Lingala

133 Xhosa

134 Yoruba

135 Chinese (CHI)

136 Zulu

Laothian

Lithuanian

–

_{Download from Www.Somanuals.co}4_m9_{. All Manuals Search And Download.}

01A11

TROUBLESHOOTING GUIDE

TV/VCR

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

PROBLEM

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Make sure the power is turned on.

No power.

•

Remote Control Doesn’t Work

No picture and sound.

Is TV/DVD plugged in?

Power at outlet?

Check batteries in Remote Control.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the TV/DVD/VHS program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust COLOR control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Check for local interference.

No picture or poor picture on

TV/DVD/VHS.

No sound or poor sound.

Bars On Screen

Picture Distorted or Blurred

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Picture OK, Sound Poor

Timer recording is not possible.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/DVD/VHS clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

Cannot go into Record mode.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

PROBLEM

CORRECTIVE ACTION

Playback picture is partially noisy. • ^{Adjust tracking control for a better picture using the CHANNEL K}

• ^{or L button on the TV/DVD/VHS.}

No picture but the audio is OK in

playback.

• ^{Head cleaning may be necessary. Refer to “AUTO HEAD}

• ^{CLEANING” on page 53.}

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape^.• ^{copy guard protection.}

Uneven color

• Make sure the AC cord is connected to an AC outlet.

• ^{Check batteries in remote control.}

• ^{You can not copy a copyrighted video tape. You are experiencing}

• ^{Unplug the AC cord for about 30 minutes, then plug it again.}

CLOSED CAPTION PROBLEM

My TV/DVD/VHS is showing

captions that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/DVD/VHS will not show

the text dialogue

• Captions that are delayed a few seconds behind the actual

are common for live broadcast. Most captioning production

in its entirety or there is a delay of • companies can display a dialogue to a maximum of 220 words

what is being said.

• per minute. If a dialogue exceeds that rate, selective editing is used

• to insure that the captions remain up-to-date with the current

• TV screen dialogue.

My captions are scrambled with

white boxes on the TV screen.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

–

_{Download from Www.Somanuals.co}5_m1_{. All Manuals Search And Download.}

01A11

DVD

If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the

player, consulting the following checklist.

Symptom

No power.

Cause

Loose power plug.

Remedy

Insert the power plug firmly into the wall out

•

let.

The player does not

respond to the

The remote control is not aimed Aim the remote control directly at the sensor

•

at the sensor on the TV/DVD.

Obstacles present between the

remote control and the sensor.

The remote control is too far

away from the TV/DVD.

Dead batteries.

on the TV/DVD.

Remove the obstacles from the signal path.

•

remote control.

•

Use the remote control within 7m of

the TV/DVD.

Replace the batteries.

Connect the video cables firmly.

Insert a correct video disc that plays on this

TV/DVD.

Insert a disc.

Clean the disc.

Place the disc correctly, with the label side up.

Cancel the parental lock or change the control

level.

•

No picture

Loose video connection.

Wrong disc.

Disc cannot be

played

No disc.

Dirty disc.

Disc is placed upside down.

Parental lock is active.

•

No sound

Loose audio connection.

The power of the connected

audio component is off.

Connect the audio cables firmly.

Turn the power of the audio component on.

•

Wrong audio output settings.

Wrong input settings on the

connected audio component.

Immediately after playing,

press fast forward or in reverse.

Correct the audio output settings.

Correct the input settings on the audio

component.

There are some cases where pictures may be

slightly distorted, which are not a sign of a

malfunction.

No malfunction.

•

Distorted picture

Audio or subtitle

language does not

match the setup.

The camera angle

cannot be changed.

The selected language is not

available for audio or subtitles

on the DVD.

The DVD does not contain

sequences recorded from

different camera angles.

The DVD does not contain

audio source or subtitles in the

selected language.

That operation is prohibited by

the TV/DVD or disc.

•

Audio or subtitle

language cannot be

changed.

"Prohibited icon"

appears on the

screen, prohibiting

an operation.

CD sound dropout

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

Scratched disc

Replace the disc with unscratched one.

•

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

CABINET CLEANING

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-968-3429, to

locate an Authorized Service Center.

NOTES:

Wipe the front panel and other exterior surfaces of

the TV/DVD with a soft cloth immersed in luke-

warm water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/DVD. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

Should your TV/DVD become inoperative, do not

•

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

Playback picture may become blurred of interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your TV/DVD/VHS may

need to be cleaned.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the player still does not perform properly when it is operated while referring to the relevant sections and to

"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult

your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

•

DISC HANDLING

Use discs which have the following logos on them.

(Optical audio digital discs.)

•

To clean-off, use a soft cloth.

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

•

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

Always store the disc in its protective case when it

is not used.

•

Do not use detergent or abrasive cleaning agents.

–

_{Download from Www.Somanuals.co}5_m3_{. All Manuals Search And Download.}

01A11

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

TV/VCR

CRT :

19 inch in-line gun, 90˚

deflection tube

NTSC-M

OTHER SPECIFICATIONS

Terminals

Television system :

Closed caption system :§15.119/FCC

Antenna input:

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary four-head

1/2 inch

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output:

1/8” stereo (3.5 mm)

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

One pin jack,

500m Vpp (75 ohm)

Analog audio L/R

output :

Remote control:

#2~#6

#7~#13

#14~#69

RCA connector [ 2

Digital encoded

infrared light system

Operating

temperature:

VHF :

5ºC to 40ºC

(41ºF~104ºF)

Power requirements: AC 120V, 60Hz

Power consumption

MID band :

SUPER band :

HYPER band :

A5~A1, A~I

J~W

W+1~W+84

(Maximum):

Picture tube:

Dimensions:

85W

19"

H:19-21/32” (500mm)

W:23-13/16” (605mm)

D:18-11/16” (475mm)

48.5 lbs (22kg)

Remote Control Unit with

2"AA"batteries

Owner’s Manual

DVD

Product type:

Discs:

Output signal format: NTSC color

Frequency response

DVD Player

DVD video, Audio CD

Weight:

Accessories:

(out put jack)

DVD (linear sound): 20 Hz to 22 kHz

(sample rate: 48 kHz)

20 Hz to 44 kHz

(sample rate: 96 kHz)

20 Hz to 20 kHz

CD:

Signal-to-noise ratio

(S/N ratio)(out put jack)

CD:

100 dB (EIAJ)

Dynamic range

(out put jack)

DVD (linear sound): 85 dB

CD:

84 dB (EIAJ)

Total distortion factor

CD:

Wow and flutter:

0.07% (EIAJ)

Below the measurement

limitation (+/-0.001%

W PEAK) (EIAJ)

Designs and specifications are subject to change without notice and without our legal obligation.

If there is a discrepancy between languages, the default language will be English.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

MEMO

–

_{Download from Www.Somanuals.co}5_m5_{. All Manuals Search And Download.}

01A11

retirarlos de ella.

7.Bandeja de carga del disco

INDICE

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 56

PANEL FRONTAL DEL televisor/DVD/VHS . . . . . . . . . 56

MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 56

VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 58

CONEXIONES DE ANTENA/TELEVISIÓN

8.Indicador de DVD

Parpadea durante el modo del DVD.

9.Botón SELECT

Púlselo para cambiar a un modo de televisor,

modo de entrada externa o modo de DVD.

POR CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

INSTALACIÓN DE LAS PILAS. . . . . . . . . . . . . . . . . . . 58

CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 58

MODE DE ENTRADA EXTERNA. . . . . . . . . . . . . . . . . 58

CONEXIÓN A UN SISTEMA ESTÉREO (Para DVD) . . 58

CONEXIÓN A UN AMPLIFICADOR EQUIPADO CON

TOMAS DE ENTRADA DIGITAL, PLATINA MD O

PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . . . . . . 58

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

O A UN DECODIFICADOR DTS (Para DVD) . . . . . . . . 59

10. Indicador del televisor/ la videograbadora

(TV/VCR)

Parpadea durante el modo del televisor/ la

videograbadora

11. Botones CHANNEL K/L

Púlselo para seleccionar el canal memorizado.

Púlselo para cambiar a un modo de televisor

cuando modo de DVD.

12. Indicador de grabación (RECORD)

Parpadea durante la grabación.

TV SECTION

PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . . . 60

SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 60

PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 60

Se enciende en el modo de espera de la grabación con

temporizador.

Botón de grabación de un toque (OTR)

■

Activa la grabación de un toque. (Sólo en el televi-

sor/DVD/VHS)

DVD SECTION

■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . 61

REPRODUCCIÓN DE UN DVD DE VÍDEO O UN CD DE

AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

13. Botón de grabación (REC)

Púlselo para iniciar la grabación manual.

14. Botón de rebobinado (REW) (para televisor/

videograbadora)

CONTROLES DE

Púlselo para rebobinar la cinta, o para ver la imagen en

retroceso rápido durante el modo de reproducción.

(Búsqueda con rebobinado)

OPERACIÓN Y FUNCIONES

15. Botón de avance rápido (FWD) (para televisor/

videograbadora)

PANEL FRONTAL DEL

TELEVISOR/DVD

Púlselo para avanzar rápidamente la cinta, o para ver la

imagen en avance rápido durante el modo de reproduc-

ción. (Búsqueda con avance rápido)

Consulte la figura 1 de la página 9

16. Botón de parada (STOP)

Púlselo para detener la cinta.

Botón de expulsión (EJECT)

MANDO A DISTANCIA

Púlselo en el modo de parada para expulsar la cinta del

televisor/videograbadora.

Consulte la figura 2 de la página 9

17. Ventanilla del sensor del mando a distancia

VISTA POSTERIOR

18. Toma HEADPHONE

Para conectar auriculares (no suministrados) y

escuchar en privado.

Consulte la figura 3 de la página 10

19. Toma de entrada VIDEO

1.Botón POWER

Conecte aquí la toma de salida de vídeo de una

videocámara o de una videograbadora.

20. Tomas de entrada AUDIO L/R

Púlselo para conectar y desconectar la alimentación.

2.Botones VOLUME K/L

Púlselos para controlar el nivel del volumen para

el DVD y el televisor.

3.Botones SKIP (para DVD)

Salta capítulos o pistas hasta un punto deseado.

4.Botón PLAY

Inicia la reproducción del contenido del disco o la

cinta.

5.Botón STOP

Detiene la operación del disco o la cinta.

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

21. Compartimiento del videocasete

22. Botón PICTURE

Presione para entrar en el modo de ajuste de ima-

gen.

6.Botón OPEN/CLOSE

Púlselo para insertar discos en la bandeja o

–

Download from Www.Somanuals.com. All Manuals Search And Download.

1D18

23. Botones de números

38. Botón RETURN

Para volver a la operación anterior.

Modo del televisor:

Pulse dos dígitos para tener acceso directamente

al canal deseado.

39. Botón ENTER

Púlselo para establecer un ajuste.

Recuerde pulsar "0" antes de elegir un canal de un

solo dígito.

Botón +100

Púlselo para seleccionar canales de televisión por

cable cuyo número sea igual o superior al 100.

Modo DVD:

Púlselo para introducir el número deseado.

Botón +10

Púlselo para introducir los números deseados

cuyo número sea igual o superior al 10.

40. Botones de flechas

Modo de televisor:

Púlselo para seleccionar un modo de ajuste desde

el menú que aparece en la pantalla del televisor.

Púlselo para seleccionar o ajustar desde un menú

particular.

Modo de DVD:

Se utiliza cuando se hacen ajustes mientras se

observa la visualización en una pantalla de televisor.

41. Botón DISC MENU

Visualiza menús de DVD.

24. Botón PAUSE

Hace una pausa en la operación del disco o la

cinta.

42. Botón ZOOM

Amplia parte de una imagen de DVD reproducida.

25. Botón de velocidad de cinta (SPEED)

Púlselo para elegir la velocidad de grabación deseada:

SP/SLP.

43. Botón MUTE

Pulse el botón MUTE para apagar el sonido de un

programa de TV. La visualización del nivel del

sonido cambia de ROJO CLARO a AZUL

CLARO.) Pulse de nuevo el botón MUTE o el

botón VOL K o L para restaurar el sonido.

26. Botón C-RESET

Púlselo para reponer el contador a 0:00:00.

27. Botón DISPLAY

44. Botón DVD

Modo del televisor/ la videograbadora:

Púlselo para visualizar el número del canal en la

pantalla. Si lo pulsa de nuevo, el número del canal

desaparecerá.

Púlselo para cambiar a un modo de DVD.

45. Botón TV/VCR

Púlselo para cambiar a un modo de televisor/

videograbadora.

Modo de DVD:

Visualiza el estado actual en la pantalla del televi-

sor con fines de comprobación.

46. Toma de entrada ANT.

Conéctela a una antena, sistema de televisión por

cable o sistema de satélite.

28. Botón SETUP

Púlselo para activar o salir del modo de menús de

televisor o preparación de DVD.

47. Cable de alimentación

Conéctelo a una toma de CA convencional (120

V/60 Hz).

29. Botón TITLE

Visualiza el menú de títulos.

NOTA: Retire el cable de alimentación del gancho

para evitar romperlo antes de conectarlo a

una toma de CA convencional.

30. Botón CLEAR

Repone un ajuste.

48. Toma de salida de audio digital COAXIAL

Conéctela a la entrada digital de un amplificador o

decodificador externo.

31. Botón MODE

Activa el modo de reproducción programada o el

modo de reproducción aleatoria.

49. Toma de salida AUDIO L/R

32. Botón SEARCH MODE

Conéctela a la entrada de audio analógico de un

amplificador o decodificador externo.

NOTA: Las tomas de entrada de audio (roha y

blanca) en el lado trasero sirven para pro-

ducir no el son televisor ni el son de

entrada externa, sino el son DVD.

Púlselo para localizar un punto deseado.

33. Botón AUDIO

Púlselo para seleccionar un idioma de audio o un

modo de sonido deseado.

34. Botón SUBTITLE

Púlselo para seleccionar un idioma de subtítulos

deseado.

35. Botón REPEAT

Repite la reproducción del disco, título, capítulo o

pista actual.

36. Botón ANGLE

Púlselo para cambiar el ángulo de la cámara y

verde, desde un ángulo diferente, la secuencia que

está siendo reproducida.

37. Botón A-B REPEAT

Repite la reproducción de una sección seleccionada.

–

_{Download from Www.Somanuals.co}5_m7_{. All Manuals Search And Download.}

1D18

fuente a las tomas AUDIO L/R y VIDEO de este tele-

visor/DVD/VHS. Y luego pulse el botón SELECT

hasta que "VIDEO" aparezca en la pantalla.

PREPARACIÓN PARA LA

UTILIZACIÓN

CONEXIONES DE ANTENA/

TELEVISIÓN POR CABLE

NOTA:

Cuando conecte una videograbadora monoaural

•

(otra fuente) a este televisor/DVD/VHS, conecte la

toma de salida de audio de la videograbadora

monoaural (otra fuente) a la toma AUDIO L de este

televisor/DVD/VHS. El audio saldrá igualmente en

los canales L y R.

Consulte la figura 4 de la página 11

ANTENAS SEPARADAS DE VHF/UHF

En algunas áreas será necesario utilizar una antena

exterior.

Consulte la figura 5 de la página 12

Conexiones de antena/televisión por cable

Continúa en la página siguiente.

Consulte la figura 4 de la página 11

TELEVISIÓN POR CABLE SIN CAJA DE

CONVERTIDOR/DECODIFICADOR

MODO DE ENTRADA EXTERNA

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los

cables de salida de audio/vídeo del equipo de repro-

ducción a las tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón

CHANNEL K o L hasta que “AUX” aparezca en la

pantalla.

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su

televisor/DVD/VHS sin necesidad de caja de conver-

tidor.

Consulte la figura 4 de la página 11

Usted puede programar el temporizador para que

explore todos los canales que puedan recibirse en su

zona.

TELEVISIÓN POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATÉLITE

Si su proveedor de servicios de televisión por cable le

suministra una caja de convertidor o si usted utiliza

un sistema de satélite, podrá utilizar la conexión bási-

ca mostrada aquí.

CONEXIÓN A UN SISTEMA

ESTÉREO (Para DVD)

Consulte la figura 6 de la página 14

NOTAS:

Consulte la figura 4 de la página 11

Asegúrese de desconectar la alimentación a todos

los componentes del sistema antes de hacer la

conexión a otro componente.

•

INSTALACIÓN DE LAS PILAS

1) Abra la tapa del compartimiento de las pilas del

mando a distancia presionándola en el sentido de

la flecha.

2) Inserte 2 pilas tamaño "AA" en su compartimiento

colocando las polaridades (+/-) en sus posiciones

correspondientes.

Consulte el manual del propietario de su sistema

estéreo y de cualquier otro componente que vaya a

conectar al televisor/DVD/VHS.

•

Las tomas de entrada de audio (roha y blanca) en el

lado trasero sirven para producir no el son televisor

ni el son de entrada externa, sino el son DVD.

•

CONEXIÓN A UN

3) Vuelva a poner la tapa.

AMPLIFICADOR EQUIPADO

CON TOMAS DE ENTRADA

DIGITAL, PLATINA MD O

PLATINA DAT (Para DVD)

CONEXIÓN A TOMAS DE

ENTRADA EXTERNA

Utilice un cable digital coaxial (de venta en el comer-

cio) para las conexiones de audio.

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada de audio/vídeo de la parte delantera del tele-

visor/DVD/VHS.

Consulte la figura 7 de la página 14

Conecte las tomas de salida de audio/vídeo de otra

–

Download from Www.Somanuals.com. All Manuals Search And Download.

1D18

NOTAS:

A menos que se haga la conexión a un decodifi-

cador Dolby Digital o DTS, ponga DOLBY DIGI-

TAL y DTS en OFF para la salida de audio en el

modo de preparación. La reproducción en el televi-

sor/DVD/VHS utilizando los ajustes incorrectos

puede generar distorsión de ruido, y también puede

estropear los altavoces.

El audio se silenciará cuando DOLBY DIGITAL se

ponga en OFF y VIRTUAL 3D se ponga en ON

para la salida de audio en el modo de preparación y

usted seleccione la fuente de audio del formato de

sonido ambiental Dolby Digital de 5,1 canales.

•

La fuente de audio de un disco del formato de

•

sonido ambiental Dolby Digital de 5,1 canales no

puede ser grabada como sonido digital por una

platina MD o DAT.

Asegúrese de desconectar la alimentación de todos

los componentes del sistema antes de hacer la

conexión a otro componente.

•

Consulte los manuales del propietario de los com-

ponentes que vaya a conectar al

televisor/DVD/VHS.

•

Ponga DOLBY DIGITAL y DTS en OFF para la

•

salida de audio en el modo de preparación. La

reproducción en el televisor/DVD/VHS utilizando

los ajustes incorrectos puede generar distorsión de

ruido, y también puede estropear los altavoces.

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la D

doble son marcas de fábrica de Dolby

Laboratories.

El audio se silenciará cuando DOLBY DIGITAL se

•

ponga en OFF y VIRTUAL 3D se ponga en ON

para la salida de audio en el modo de preparación y

usted seleccione la fuente de audio del formato de

sonido ambiental Dolby Digital de 5,1 canales.

“DTS” y “DTS Digital Out” son marcas de

fábrica de Digital Theater Systems, Inc.

CONEXIÓN A UN

DECODIFICADOR DOLBY

DIGITAL O A UN

DECODIFICADOR DTS

(Para DVD)

Si se utiliza este televisor/DVD/VHS para reproducir

fuentes del formato de sonido ambiental Dolby

Digital de 5,1 canales o de sonido ambiental DTS, el

televisor/DVD/VHS dará salida a un flujo de datos

Dolby Digital o DTS desde su toma de salida de

audio digital COAXIAL. Conectando el reproductor a

un decodificador Dolby Digital o DTS, usted podrá

disfrutar de un ambiente más convincente y real con

un sonido ambiental potente y de alta calidad de tipo

profesional tal como el que se oye en salas de cine.

Utilice cables digitales coaxiales (de venta en el com-

ercio) para las conexiones de audio.

Consulte la figura 8 de la página 13

NOTAS:

Asegúrese de desconectar la alimentación de todos

los componentes del sistema antes de hacer la

conexión a otro componente.

•

Consulte los manuales del propietario de los com-

ponentes que vaya a conectar al

televisor/DVD/VHS.

•

Si conecta un decodificador Dolby Digital, ponga

DOLBY DIGITAL en ON para la salida de audio

en el modo de preparación.

•

Si conecta un decodificador DTS, ponga DTS en

ON para la salida de audio en el modo de

preparación.

•

–

_{Download from Www.Somanuals.co}5_m9_{. All Manuals Search And Download.}

1D18

TV SECTION

AJUSTE DEL RELOJ

Cerciórese...

La alimentación del televisor/videograbadora

deberá estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 7 de mayo de 2002

HORA: 5:40 PM

PREPARACIÓN PARA LA

UTILIZACIÓN

•

PREPARACIÓN DE CANALES

POR PRIMERA VEZ

Pulse el botón SETUP en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”. Luego, pulse el botón F.FWD/B.

Conecte el cable de alimentación a una toma de CA

convencional.

NOTA: Si aparecen algunos dígitos en la esquina de

la pantalla, pulse el botón POWER sin des-

enchufar el cable de alimentación.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”. Luego, pulse el botón

F.FWD/B.

Pulse el botón POWER para encender el

televisor/DVD/VHS.

Pulse el botón PLAY/K o STOP/L hasta que aparez-

ca el mes deseado. (Ejemplo: Mayo - 05) Luego,

pulse el botón F.FWD/B.

Seleccione "ESPAÑOL" o "ENGLISH" (inglés),

"FRANÇAIS" (francés) utilizando el botón de flecha

B o s.

Pulse el botón PLAY/K o STOP/L hasta que aparez-

ca el día del mes deseado. (Ejemplo: 7 - 07) Luego,

pulse el botón F.FWD/B.

Pulse el botón flecha K o L para señalar “AUTOP-

RESELECCION”.

Luego pulse el botón flecha B. El sintonizador

explorará y memorizará todos los canales activos de

su área.

Pulse el botón PLAY/K o STOP/L hasta que aparez-

ca el año deseado. (Ejemplo: 2002) Luego, pulse el

botón F.FWD/B.

NOTAS:

El televisor/videograbadora distingue entre los

canales de televisión estándar y los canales de tele-

visor por cable.

•

Pulse el botón PLAY/K o STOP/L hasta que aparez-

ca la hora deseada. (Ejemplo: 5, PM) Luego, pulse el

botón F.FWD/B.

Si desea reproducir o grabar una cinta ANTES de

preajustar el sintonizador, usted tendrá que pulsar

el botón SETUP en el mando a distancia. Para

preajustar de nuevo el sintonizador, consulte

“REPETICIÓN DE LA PREPARACIÓN DE

CANALES”.

La unidad de televisor/videograbadora puede

reconocer los canales de TV como ellos de TV por

cable a causa de los condiciones de recepción. En

este caso, pruebe el preajuste automático de nuevo

en los condiciones finas de recepción.

•

Pulse el botón PLAY/K o STOP/L hasta que aparez-

•

ca el minuto deseado. (Ejemplo: 40)

Pulse el botón SRTUP en el mando a distancia.

Aunque los segundos no se visualizan, éstos

empiezan a contar desde 00 cuando se pulsa SETUP

en el mando a distancia. Utilice esta función para sin-

cronizar el reloj con la hora correcta.

El sintonizador se para en el canal memorizado más

bajo. Si desea recuperar canales seleccionados, usted

podrá seleccionar directamente el canal deseado con

los botones numerados del mando a distancia o con

los botones CHANNEL K o L.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

1D18

DVD SECTION

REPRODUCCIÓN DE UN

DISCO

REPRODUCCIÓN DE UN DVD

DE VÍDEO O UN CD DE AUDIO

DVD

Para empezar

Conecte la alimentación del televisor, amplificador y

cualquier otro componente que esté conectado al

reproductor DVD. (Cambie el sistema de entrada para

adaptarlo al reproductor DVD, y compruebe que el

volumen del sonido sea correcto.)

Pulse el botón POWER.

¡La alimentación se conectará.

Pulse el botón OPEN/CLOSE.

¡La bandeja de carga del disco se abrirá.

Ponga un disco en la bandeja.

¡Asegúrese de que el disco esté correctamente asen-

tado en el hueco correcto, con el lado de la etiqueta

hacia arriba.

Pulse el botón PLAY.

¡La bandeja se cerrará automáticamente y la repro-

ducción empezará desde el primer capítulo o pista

del disco. Necesitará pulsar el botón PLAY sólo

cuando la bandeja haya sido cerrada pulsando el

botón OPEN/CLOSE.

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú tal vez aparezca en la pan-

talla. En este caso, consulte "UTILIZACIÓN DEL

MENÚ DE TÍTULOS".

Pulse el botón STOP para detener la reproducción.

–

_{Download from Www.Somanuals.co}6_m1_{. All Manuals Search And Download.}

1D18

MEMO

–

Download from Www.Somanuals.com. All Manuals Search And Download.

1D18

MEMO

–

_{Download from Www.Somanuals.co}6_m3_{. All Manuals Search And Download.}

1D18

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of

original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI

AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,

please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC.

Customer Service

100 North Street; Teterboro, NJ 07608

Tel :1-800-968-3429

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

0EMN01945

TD360UA ★★★★★

Download from Www.Somanuals.com. All Manuals Search And Download.

Sharp Air Conditioner CV P09FX User Manual
Shoprider Wheelchair UL8W36 User Manual
Soleus Air Air Conditioner KFHIP 09 OD User Manual
Sony Camcorder PMW 100 User Manual
Sony Cell Phone 1266 1567 User Manual
Sony Indoor Furnishings WS FV10D User Manual
Sony Video Game Console SCPH 70001 User Manual
Speco Technologies Portable Speaker SP6MAT User Manual
Stanley Black Decker Trash Compactor HSX SERIES User Manual
Sterling Plumbing Dehumidifier 100 User Manual