Sylvania TV DVD Combo 6519DA User Manual

OWNER’S

MANUAL

19-INCH COLOR TV/DVD

6519DA

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1-800-968-3429.

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

12.Power-Cord Protection-Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying par-

ticular attention to cords at plugs, convenience receptacles,

and the point where they exit from the appliance.

19.Damage Requiring Service-Unplug this TV/DVD from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/DVD.

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/DVD, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

c. If the TV/DVD has been exposed to rain or water.

d. If the TV/DVD does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/DVD to its normal operation.

e. If the TV/DVD has been dropped or damaged in any way.

f. When the TV/DVD exhibits a distinct change in perfor-

mance-this indicates a need for service.

14.Lightning-For added protection for this TV/DVD receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/DVD due to lightning and

power-line surges.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

21.Safety Check-Upon completion of any service or repairs to

this TV/DVD, ask the service technician to perform routine

safety checks to determine that the TV/DVD is in proper

operating condition.

22.Heat-This TV/DVD product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/DVD through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/DVD.

18.Servicing-Do not attempt to service this TV/DVD yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to qualified

service personnel.

- 3 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

- 4 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

LOCATION

WARNING

For safe operation and satisfactory performance of

your TV/DVD, keep the following in mind when

selecting a place for its installation:

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a TV/DVD

which has moisture, it may damage the DVD and

TV/DVD. Therefore when the condensation occurs

inside the unit, turn the POWER button on and allow

at least 2 hours for the unit to dry out.

Shield it from direct sunlight and keep it away

from sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

•

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/DVD near strong magnetic fields.

Avoid moving TV/DVD to locations where temper-

•

ature differences are extreme.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the

TV/DVD disc loading tray.

•

Do not place anything directly on top of the unit.

•

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 5 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

PAUSING PLAYBACK OR DISPLAYING

A STILL PICTURE . . . . . . . . . . . . . . . . . . . . .22

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

RESUMING PLAYBACK FROM THE

POINT WHERE PLAYBACK STOPPED . . . .22

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .5

STEPPING THROUGH FRAMES . . . . . . . . . .22

FAST FORWARD/REVERSE . . . . . . . . . . . . .23

SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .23

STARTING FROM A DESIRED TRACK . . . .23

STARTING FROM A DESIRED TIME COUNT .23

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .7

C OPERATING CONTROLS AND FUNCTIONS 8

PLAYING FROM A DESIRED TITLE OR

CHAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

C PREPARATION FOR USE . . . . . . . . . . . . . . .10

ANTENNA/CABLE CONNECTIONS . . . . . . .10

INSTALLING THE BATTERIES . . . . . . . . . . .12

RANDOM (Audio CD) . . . . . . . . . . . . . . . . . .24

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . .25

PROGRAM (Audio CD) . . . . . . . . . . . . . . . . .25

CONNECTING TO EXTERNAL INPUT JACKS .12

CONNECTING TO A STEREO SYSTEM (for DVD) .13

C SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . .26

CONNECTING TO AN AMPLIFIER

EQUIPPED WITH DIGITAL INPUT JACKS,

MD DECK OR DAT DECK (for DVD) . . . . . .13

CHANGING THE AUDIO LANGUAGE OR

SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . .26

CHANGING THE SUBTITLE LANGUAGE . .27

CONNECTING TO A DOLBY DIGITAL

DECODER OR DTS DECODER (for DVD) . .14

CHANGING THE CAMERA ANGLE

(Multi-Angle Pictures) . . . . . . . . . . . . . . . . . . .27

TV SECTION

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .15

CHANGING THE ON-SCREEN DISPLAY . . .28

C CHANGING THE SETUP ITEMS . . . . . . . . .29

LANGUAGE SETTINGS . . . . . . . . . . . . . . . .29

VIDEO SETTINGS . . . . . . . . . . . . . . . . . . . . .30

AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .30

PARENTAL LOCK . . . . . . . . . . . . . . . . . . . . .31

OTHER SETTINGS . . . . . . . . . . . . . . . . . . . . .32

LANGUAGE SELECTION . . . . . . . . . . . . . . .15

CHANNEL PRESETTING . . . . . . . . . . . . . . .15

C OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . .16

WATCHING A TV PROGRAM . . . . . . . . . . . .16

SELECTING THE SLEEP TIMER . . . . . . . . .16

CLOSED CAPTION . . . . . . . . . . . . . . . . . . . .16

PICTURE ADJUSTMENT . . . . . . . . . . . . . . . .17

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .18

C LANGUAGE CODE LIST . . . . . . . . . . . . . . . .33

C TROUBLESHOOTING GUIDE . . . . . . . . . . .34

DVD SECTION

C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .20

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .37

DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .37

PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .20

DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .20

SYMBOLS USED IN THIS MANUAL . . . . . .20

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .38

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .21

PLAYING A DVD VIDEO OR AN AUDIO CD .21

USING THE DVD MENUS . . . . . . . . . . . . . . .21

USING THE TITLE MENU . . . . . . . . . . . . . . .22

- 6 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

DVD

Tinted, Bright Black Matrix Picture Tube

181 Channel Selection– All VHF/UHF channels

plus up to 125 cable channels.

PLL Frequency Synthesized Tuning– The latest

PLL frequency synthesized electronic tuning sys-

tem provides free and easy channel selection, and

lets you tune directly to any channel using the

channel number buttons (0~9 and +100-key) on the

remote control.

Dolby Digital sound– This player can handle

•

Dolby Digital surround sound having 5.1 channels

when connected to a Dolby Digital decoder.

Still/fast/slow/step playback– Various playback

modes are available including still pictures, fast

forward/reverse, slow motion and step frames.

Random playback for audio CD– This player can

shuffle the order of tracks to play them in random

order.

Program playback for audio CD– You can pro-

gram the order of tracks to play them in any

desired order.

DVD menus in a desired language– You can dis-

play DVD menus in a desired language, if avail-

able on a DVD.

Screen saver and auto power-off functions–

Screen saver is automatically activated when there

is no input from the player or the remote control

for one minute in stop mode. The power is auto-

matically turned off when there is no input for 31

minutes in still or stop mode.

Subtitles in a desired language– You can select a

desired language for the display subtitles, if that

language is available on a disc.

Selecting a camera angle– You can select the

desired camera angle, if a disc contains sequences

recorded from different angles.

Choices for audio language and sound mode–

You can select the desired audio language and

sound mode, if different languages and modes are

available on a disc.

•

On-Screen Function Display.

Full-Function Remote Control

Sleep Timer

•

Closed Caption Decoder– You may view special-

ly labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Auto Shut Off Function– If there is no air signal

input from the antenna terminal and no operation

for 15 minutes, the TV will turn itself off automati-

cally.

•

V-CHIP– Enables parents to prevent their children

from watching inappropriate material on TV.

•

Parental lock– You can set the control level to

limit playback of discs which may not be suitable

for children.

Automatic detection of discs– This player auto-

matically detects if a loaded disc is DVD or audio

CD.

On-screen display– Information about the current

operation can be displayed on a TV screen, allow-

ing you to confirm the currently active functions

(such as program playback), on the TV screen

using the remote control.

•

SUPPLIED ACCESSORIES

Remote Control Unit

2 AA Batteries

PART NO. (N0285UD)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

•

- 7 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- TV/DVD FRONT PANEL - [Fig. 1]

VOLUME

CHANNEL

STOP

SKIP PLAY

SKIP

PAUSE OPEN/CLOSE

HEADPHONE

POWER

VIDEO

L-AUDIO-R

1 2

8 18 10 18 12 13 14

- REMOTE CONTROL - [Fig. 2]

1.Disc loading tray

2.VIDEO input jack– Connect to the video output

jack of a video camera or VCR.

3.AUDIO L/R input jacks– Connect to the audio

output jacks of a video camera or VCR.

4.POWER button– Press to turn the power on and off.

5.VOLUME K/L buttons– Press to control the vol-

ume level for the DVD and TV.

6.CHANNEL K/L buttons– Press to select memo-

rized channel.

OPEN/

POWER

DVD

CH.

+100

7.Remote Sensor Window

VOL.

SLEEP

+10

8.STOP button– Stops operation of the disc.

9.REV button– Fast reverses playback to a desired

point.

10. PLAY button– Starts playback of the disc contents.

11. FWD button– Fast forwards playback to a desired

point.

12. PAUSE button– Pauses the current disc opera-

tion.

13. OPEN/CLOSE button– Press to insert discs into

or remove them from the tray.

SKIP

SELECT MUTE

SLOW

PLAY

STOP

REV

FWD

PAUSE

MODE

SETUP

ENTER

TITLE

RETURN

CLEAR SEARCH MODE REPEAT

A-B

14. HEADPHONE jack– To connect headphone (not

supplied) for personal listening.

15. TV button– Press to do TV operations.

16. NUMBER button–

DISPLAY AUDIO

SUBTITLE

ANGLE

TV Mode:

Press two digits to directly access the desired

channel.

Remember to press a "0" before a single digit

channel.

+100 button–

Press to select cable channels which are equal or

greater than number 100.

DVD Mode:

Press to enter the desired number.

+10 button–

Press to enter the desired numbers which are

equal or greater than number 10.

To use as TV remote control, press the TV but-

ton on the remote control after TV mode is

selected. TV operation buttons have been indi-

cated by blue or white.

To use as DVD remote control, press the DVD

button on the remote control after DVD mode is

selected. DVD operation buttons have been

indicated by yellow or white.

•

- 8 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

- REAR VIEW - [Fig. 3]

ANT.

DIGITAL AUDIO OUT

(PCM/BITSTREAM)

AUDIO OUT

COAXIAL

38 39

30. RETURN button– Returns to the previous opera-

17. SLEEP button– Press the SLEEP button to dis-

play the sleep timer and start the function. The

shut off time can be determined by the number of

times you press the button. (0, 10, 20, 30,..90, 0

minutes)

tion.

31. ENTER button– Press to accept a setting.

32. Arrow buttons–

TV Mode:

18. SKIP buttons– Skip chapters or tracks to a

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

desired point.

19. MODE button– Activates program playback or

random playback mode.

DVD Mode:

20. SETUP button– Press to enter the setup mode or

Use when making settings while watching the dis-

play on a TV screen.

to change setup items.

21. TITLE button– Displays the title menu.

33. MENU button– Displays the DVD and TV

menus.

22. CLEAR button– Resets a setting.

34. SELECT button– Press to change of TV mode,

23. DISPLAY button–

external input mode or DVD mode.

TV Mode:

35. MUTE button– Press the MUTE button to turn off

the sound portion of the TV program. (Volume

level display turns LIGHT RED from LIGHT

BLUE.) Press the MUTE button again or press

the VOL(ume) K or L button to restore sound.

Press to display the channel number on the

screen. If you press it again, the channel number

will disappear.

DVD Mode:

Displays the current status on the TV screen for

checking purposes.

36. DVD button– Press to do DVD operations.

24. SEARCH MODE button– Press to locate a

desired point.

37. Power cord– Connect to a standard AC outlet

(120V/60Hz).

NOTE: Remove the power cord from the hook to

avoid breaking a wire before you connect to a

standard AC outlet.

25. AUDIO button– Press to select a desired audio

language or sound mode.

26. SUBTITLE button– Press to select a desired sub-

38. COAXIAL digital audio out jack– Connect to the

title language.

other amplifier or decoder.

27. REPEAT button– Repeats playback of the cur-

39. AUDIO L/R output jack– Connect to the other

rent disc, title, chapter or track.

amplifier or decoder.

28. ANGLE button– Press to change the camera

angle to see the sequence being played back from

a different angle.

40. ANT. in jack– Connect to an antenna, cable sys-

tem, or satellite system.

29. A-B REPEAT button– Repeats playback of a

selected section.

- 9 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

VHF/UHF COMBINED ANTENNA

The VHF/UHF Rod Antenna (supplied) is detachable. Insert the stem of the antenna into the hole on the upper-

back portion of the TV/DVD. Connect the VHF/UHF Rod Antenna or VHF/UHF Combination Antenna to the

ANT. terminal of the TV/DVD as shown in the diagram below. For the best reception, fully extend the

VHF/UHF Rod Antenna and make the necessary adjustments. (Avoid touching the top section when adjusting.)

NOTE:

Before plugging the Rod antenna into antenna terminal, check that the pin is not bent. If it is bent, straighten

the pin as illustrated, then plug the pin into antenna terminal.

Bent pin

Cable Plug

(Straight pin)

(Needs to be straightened)

VHF/UHF Antenna

(Not supplied)

Rod Antenna

(Supplied)

ANT.

[Fig. 4]

NOTE:

The connection of an indoor antenna may not always give acceptable TV reception.

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor antenna.

VHF Antenna (Not supplied)

UHF Antenna

(Not supplied)

VHF/UHF

Combiner

(Not

supplied)

ANT.

Flat twin-lead cable

[Fig. 5]

- 10 -

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects directly to your TV/DVD without a converter box.

From Cable System

75-ohm Coaxial

Cable (Not

supplied)

ANT.

[Fig. 6]

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE BOX

If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic

connection shown here.

Satellite Box or

Cable Box (Not supplied)

OUT

From Cable System

or Satellite Dish

75-ohm Coaxial

Cable

(Not supplied)

ANT.

[Fig. 7]

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

- 11 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.

2)Insert 2 "AA" penlight batteries into the battery compartment in the direction indicated by the polarity (+/-)

markings.

3)Replace the cover.

CONNECTING TO EXTERNAL INPUT JACKS

When you watch a program recorded on an another source (VCR or video camera), use the audio/video input

jacks on the front of the TV/DVD.

Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks of this TV/DVD.

Then press the SELECT button until "VIDEO" appears on the screen.

NOTE:

When you connect a monaural VCR (another source) to this TV/DVD, connect the Audio output jack of the

monaural VCR (another source) to the AUDIO L jack of this TV/DVD. The audio will output in both L and

R channel equally.

•

To the audio

output jacks

[Another source]

Audio/Video

VIDEO L-AUDIO-R

coaxial cable

(not supplied)

etc.

To the video

output jack

[Front of the TV/DVD]

[Fig. 8]

- 12 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A STEREO SYSTEM (for DVD)

ANT.

DIGITAL AUDIO OUT

AUDIO OUT

(PCM/BITSTREAM)

COAXIAL

Stereo system

To Right (red) and Left (white)

AUDIO OUT jacks

(only DVD AUDIO OUT)

To ANALOG AUDIO INPUT jacks

[Fig. 9]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the

TV/DVD.

•

CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL

INPUT JACKS, MD DECK OR DAT DECK (for DVD)

Use audio coaxial digital cables (commercially available) for the audio connections.

DIGITAL AUDIO

^OUTAUDIO OUT

(PCM/BITSTREAM)

COAXIAL

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

Amplifier equipped with digital

input jacks, MD deck,

DAT deck, etc.

(only DVD AUDIO OUT)

To COAXIAL DIGITAL

AUDIO INPUT jack

[Fig. 10]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

Set DOLBY DIGITAL and DTS to OFF for audio output in the setup mode. Playing a TV/DVD using

incorrect settings may generate noise distortion, and may also damage the speakers.

When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and

you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.

•

- 13 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A DOLBY DIGITAL DECODER

OR DTS DECODER (for DVD)

If using this TV/DVD to play back a TV/DVD in a 5.1 channel Dolby Digital surround or DTS surround for-

mat, the TV/DVD outputs a Dolby Digital or DTS data stream from its COAXIAL digital audio out jack. By

hooking the player up to a Dolby Digital or DTS decoder, you can enjoy a more convincing, realistic ambi-

ence with powerful and high-quality surround sound of a professional standard such as can be heard in movie

theaters.

Use audio coaxial digital cables (commercially available) for the audio connections.

Center

speaker

Front speaker

(left)

Front speaker

(right)

DIGITAL AUDIO OUT

(PCM/BITSTREAM)

AUDIO OUT

COAXIAL

Dolby Digital

or DTS decoder

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 11]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.

If connected to a DTS decoder, set DTS to ON for audio output in the setup mode.

Unless connected to a Dolby Digital decoder or a DTS decoder, set DOLBY DIGITAL and DTS to OFF for

audio output in the setup mode. Playing a TV/DVD using incorrect settings may generate noise distortion,

and may also damage the speakers.

•

When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and

you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.

•

Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D

symbol are trademarks of Dolby

Laboratories. Confidential Unpublished

“DTS” and “DTS Digital Out” are trademarks of

Digital Theater Systems, Inc.

- 14 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

TV SECTION

SET UP FOR USE

Getting started

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

Press the Arrow K or L button to

point to "CHANNEL SET". Then,

press the Arrow B button.

Connect the power cord to a standard AC outlet.

NOTE: If some digits appear in the corner of the

screen, press the POWER button without unplugging

the power cord.

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

Press the Arrow K or L button to

point to "AUTO MEMO". Then,

press the Arrow B button.

ADD/DELETE

AUTO MEMO

Press the POWER button to turn on the TV/DVD.

The tuner scans and memorizes all

active channels in your area.

Press the SELECT button on the remote control until

channel number or "TV" appears on the screen.

Then press the TV button.

The TV distinguishes between standard TV chan-

nels and cable channels.

•

When AUTO MEMO action is completed, the low-

est memorized channel reappears on the screen.

When you press the Arrow K or L button after

selecting AUTO MEMO, the tuner will stop at the

memorized channels only.

LANGUAGE SELECTION

If you want to change the language of the on-screen

menu, follow the procedure below.

The TV may recognize TV channels to be CATV

channels by the receiving conditions. In this case,

try AUTO MEMO action again in the fine receiv-

ing conditions.

•

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

Press the MENU button so that the

ESPAÑOL

menu display appears on the TV

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

screen.

[ADD/DELETE FUNCTION]

1)Press the MENU button so that the menu display

appears on the TV screen.

2)Press the Arrow K or L button to point to "CHAN-

NEL SET". Then, press the Arrow B button.

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

Press the Arrow K or L button to

point to "LANGUAGE".

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

3)Press the Arrow B button so that

"ADD/DELETE" is selected.

4)Use the Arrow K or L button to

select the channel you wish to

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

put into memory or to erase from

Select "ENGLISH", "ESPAÑOL" = Spanish or

"FRANÇAIS" = French by using the Arrow B or s

button.

memory.

NOTE: The display will return to the screen in

about 10 seconds. Perform "ADD/DELETE" func-

tion while this display appears on the screen.

Press the Arrow B or s button

to light up the channel number in

LIGHT BLUE if you wish to

•

Press the MENU button to exit the menu.

NOTE: An on-screen display language must be

selected each for the TV mode and DVD mode.

ADD/DELETE

AUTO MEMO

add the channel into memory.

Press the Arrow B or s button

CHANNEL PRESETTING

To preset a channel or to change a preset channel,

follow the procedure below.

•

to light up the channel number in LIGHT RED if

you wish to erase the channel from memory.

5)Press the MENU button to exit the menu.

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

Press the MENU button so that the

menu display appears on the TV

screen.

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

- 15 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS

WATCHING A TV PROGRAM

CLOSED CAPTION

This TV can receive C1 and C2 of Caption and Text.

CAPTION MODE

Select the desired channel with the CH(annel) K or

1)Characters can be displayed on the TV screen when

the received broadcast signal contains the Caption

Signals.

2)Paint-on mode: Displays input characters on the

screen immediately.

L button.

Adjust the volume to the desired listening level using

the VOL(ume) K or L button.

Pop-on mode: Once characters are stored in mem-

ory, it is displayed all at once.

Roll-up mode: Displays the characters continuous-

ly by scrolling (max. 4 lines)

Adjust picture controls for a natural looking image.

(See "PICTURE ADJUSTMENT".)

NOTE: If the CAPTION C1 or C2 is selected but the

caption signal is not included, characters will not be

displayed.

SELECTING THE SLEEP TIMER

TEXT MODE

1)Displays the text on the screen by scrolling (max. 7

lines)

2)If the received broadcast signal does not contain

the caption or text signal, no change will occur.

NOTES:

1)When your TV receives a special effects playback

signal (i.e., Search, Slow, Still) from a VCR’s

video output channel (CH3 or CH4), your TV may

not display the correct caption or text.

2)Captions and texts may not match the TV voice

exactly.

3)Interference may cause the closed caption system

not to function properly.

4)The caption or text characters will not be displayed

while the menu display or function’s display is

shown.

The sleep timer function enables you to shut off the

power without pressing the POWER button after a

desired time period.

Press the SLEEP button on the remote control.

You may change the sleep time

with pressing the SLEEP button on

the remote control repeatedly. The

SLEEP 10

timer is set up to 90 minutes, 10

minutes each time the SLEEP button is pushed. (The

timer display counts up and sleep timer will be dis-

played on the screen when you press the SLEEP but-

ton on remote control.)

5)If you see this screen!!

To cancel the sleep timer:

Press the SLEEP button repeatedly until "SLEEP 0"

is displayed.

NOTES:

If your TV displays a black box on the screen, this

means that your TV is set to TEXT mode. To clear

screen, select CAPTION C1, C2 or CAPTION

[OFF].

When you disconnect the unit from the AC outlet,

or if you have a power failure, the sleep time will

be lost.

•

When the TV mode is changed to the DVD mode,

the sleep time will be lost.

•

- 16 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

GAME MODE

Set to the most suitable position for TV GAME.

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV programs,

movies, news, prerecorded tapes, etc. with either a

dialogue caption or text display added to the pro-

gram.

[B] : ON

[s] : OFF

BRIGHT

Adjust until the whitest parts of the picture are as

bright as you prefer.

[B] : increase brightness

[s] : decrease brightness

Press the MENU button so that the menu display

appears on the TV screen.

CONTRAST

Adjust to increase or decrease contrast.

[B] : increase contrast

[s] : decrease contrast

COLOR

Press the Arrow K or L button to point to "CAP-

TION".

Adjust to be brilliant or pale color.

[B] : be brilliant color

[s] : be pale color

Press the Arrow B or s button to select the mode

you wish.

TINT

Adjust to obtain natural skin tones.

[B] : greenish tone

[s] : reddish tone

When done, press the MENU button to exit the

menu.

NOTES:

B or s

: Press the Arrow

button.

In the above steps, the picture adjustment display

•

will disappear from the TV screen after about 10

seconds unless you press any buttons, even though

you may not be finished. Press the MENU and

Arrow B button so that "PICTURE" mode is

selected. Then, press the Arrow K or L button

repeatedly until the display returns to the screen.

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [OFF]

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [ C1]

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [ C2]

If you adjust the other Picture control after you set

•

the Game mode to [ON], the Game mode is set to

[OFF] automatically. If you want to set the Game

mode, reset it to [ON].

PICTURE

: Press the Arrow L or L button.

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

CHANNEL SET

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

V-CHIP SET UP

CAPTION [ T2]

FRANÇAIS

V-CHIP SET UP

CAPTION [ T1]

[

]

[

]

[

]

[

]

GAME MODE

BRIGHT

CONTRAST

COLOR

OFF

PICTURE ADJUSTMENT

Press the MENU button so that the menu display

appears on the TV screen.

Press the Arrow B button so that "PICTURE" mode

is selected.

[

]

[

]

TINT

Select the feature you wish to adjust with the Arrow

K or L button and adjust it with the Arrow B or s

button.

- 17 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

V-CHIP SET UP

• G:

General Audience

V-CHIP enables parents to prevent their children

from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels, and Emergency Broadcast

System signals), then denies access to programming

if the program's rating meets the limitations you

select. In this case, "PROTECTED PROGRAM by

..." message appears on the TV screen.

• PG:

• PG-13:

• R:

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires

accompanying parent or adult

guardian

No one under 17 admitted

Mature audience only

• NC-17:

• X:

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

•

To block ratings, follow the steps below.

Programming may be rated by the Motion Picture

•

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

When you turn "G" to [BLOCK] or [VIEW], the

all ratings will turn to [BLOCK] or [VIEW] auto-

matically.

When you turn "X" to [VIEW], the all ratings will

turn to [VIEW] automatically.

•

You cannot access the menu when the "PROTECT-

•

ED PROGRAM by ..." message appears. In this

case, change to the unblocked channel, then press

the MENU button.

Press the MENU button to exit the menu.

[MPAA RATING SET UP]

[TV RATING SET UP]

Press the MENU button so that the menu display

appears on the TV screen.

Press the MENU button so that the menu display

appears on the TV screen.

PICTURE

CHANNEL SET

LANGUAGE [ENGLISH]

PICTURE

Press the Arrow K or L button to

point to "V-CHIP SET UP". Then,

press the Arrow B button.

CHANNEL SET

Press the Arrow K or L button to

LANGUAGE [ENGLISH]

ESPAÑOL

FRANÇAIS

ESPAÑOL

FRANÇAIS

point to "V-CHIP SET UP". Then,

press the Arrow B button.

V-CHIP SET UP

CAPTION [OFF]

V-CHIP SET UP

CAPTION [OFF]

TV RATING

MPAA RATING

Press the Arrow K or L button to

TV RATING

Press the Arrow K or L button to

MPAA RATING

point to "TV RATING". Then,

press the Arrow B button.

point to "MPAA RATING". Then,

press the Arrow B button.

[VIEW]

[BLOCK]

TV-Y

TV-Y7

TV-G

TV-PG (

TV-14

TV-MA (

[VIEW]

) [VIEW]

[VIEW]

) [VIEW]

Press the Arrow K or L button to

point to your desired item.

Then, press the Arrow B button to

select [BLOCK] or [VIEW].

PG-13

NC-17

Press the Arrow K or L button to

point to your desired item. Then,

press the Arrow B button to select

[BLOCK] or [VIEW].

(

- 18 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

• TV-Y:

• TV-Y7:

Appropriate for all children

Appropriate for children seven and

older

• TV-G:

General Audience

• TV-PG:

• TV-14:

• TV-MA:

Parental Guidance suggested.

Unsuitable for children under 14

Mature audience only

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

•

When you turn "TV-Y" to [BLOCK] or [VIEW],

the all ratings will turn to [BLOCK] or [VIEW]

automatically.

When you turn "TV-MA" to [VIEW], the all rat-

ings will turn to [VIEW] automatically.

•

When you select TV-Y7, TV-PG, TV-14, or TV-MA

and you press the Arrow B button, the sub-ratings

will appear on the TV screen.

If you select the rating category (example: TV-PG)

and turn it [BLOCK] or [VIEW], the sub-ratings

(example: V for Violence) will turn [BLOCK] or

[VIEW] automatically.

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK]. To set the sub-ratings individually, follow

the steps below.

TV-Y7

[BLOCK]

When you select [TV-Y7]:

Press the Arrow K or L button

to select "FV" (Fantasy

•

[BLOCK]

Violence). Then, press the Arrow

B button to select [BLOCK] or

[VIEW].

When you select [TV-PG],

[TV-14] or [TV-MA]:

TV-PG

[BLOCK]

•

Press the Arrow K or L button

to select "D"(Suggestive

Dialog), "L"(Coarse Language),

"S"(Sexual Situation), or

"V"(Violence). Then, press the

TV-Y

TV-Y7

TV-G

TV-PG (DLSV)[BLOCK]

TV-14 (DLSV)[BLOCK]

TV-MA ( LSV)[BLOCK]

[VIEW]

)[VIEW]

[BLOCK]

(

Arrow B button to select [BLOCK] or [VIEW].

NOTE: When you select [TV-MA], "D" does not

appear on the TV screen.

The sub-ratings which set to [BLOCK] appears

next to the rating category in the TV RATING

menu.

•

Press the MENU button to exit the menu.

- 19 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD SECTION

ABOUT THE DISCS

Photo CD

•

PLAYABLE DISCS

The following discs can be played back on this

TV/DVD.

(Never play back, otherwise malfunction may

result.)

Video CD

•

(Never play back, otherwise malfunction may

result.)

Maximum

Playback Time

Disc Type

Logo

Contents Disc Size

Approx. 4 h

(single-sided)

Approx. 8 h

Any other discs without compatibility indications

12 cm

Sound

and

Pictures

(double-sided)

DVD

Video

DISC TYPES

Approx. 80 min

(single-sided)

Approx. 160 min

(double-sided)

8 cm

[DVD]

Data on a DVD is divided into sections called

"titles", and then into subsections called "chapters",

each of which is given a title or chapter number.

Playback conditions are preset on some DVD video

discs, and these playback conditions take priority

over user operations on this player. If a function you

selected do not run as desired, refer to the manual

accompanying the disc.

12 cm

74 min

Audio

Sound

8 cm

20 min

(singles)

This player conforms to the NTSC color system. You

cannot play discs recorded in other color systems

such as PAL or SECAM.

Some discs include region codes as shown below.

•

Example

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

The number inside the symbol refers to a region of

•

the world, and a disc encoded in a specific region

format can only be played back on TV/DVD with

the same region code.

[AUDIO CD]

Data on an audio CD is divided into sections called

"tracks", each of which is given a track number.

The following discs cannot be played back on this

TV/DVD.

DVD with region codes other than 1 or ALL.

•

DVD-ROM

Example

•

DVD-R/DVD-RAM

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

•

(Never play back, otherwise malfunction may

result.)

CD-ROM

•

VSD

•

CDV

•

(Only plays back the audio part.)

CD-G

SYMBOLS USED IN THIS MANUAL

The following symbols appear below some head-

ings and in some notes in this manual, with the

following meanings.

•

(Only plays back the sound.)

CD-R

(Never play back, otherwise malfunction may

result.)

DVD

CD-I

•

Description refers to playback of DVD video discs.

Description refers to playback of audio CDs.

(Never play back, otherwise malfunction may

result.)

- 20 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING A DISC

NOTES:

Getting started

A "prohibited icon" may appear

at the bottom right on the TV

•

Turn on the power of amplifier and any other compo-

nents which are connected to the TV/DVD. (Change

the input system to suit the TV/DVD, and check that

the sound volume is correct.)

screen during operation, warning

that a prohibited operation has

been encountered by the

TV/DVD or the disc.

If a disc is dirty or has scratches, the pictures may

appear distorted and the playback operation may

stop. In such cases, clean the disc and unplug the

power cord and then plug it again before resuming

playback.

With DVDs that use some titles for playback pro-

gram signals, playback may start from the second

title, or it may skip these titles.

•

2 Press the POWER button.

The power will turn on.

•

3 Press the SELECT button on the remote con-

trol until "DVD" appears on the screen.

Then press the DVD button.

The DVD functions are active only in the DVD

mode.

To run the DVD player, press the PLAY or

OPEN/CLOSE button.

•

PLAYING A DVD VIDEO

OR AN AUDIO CD

DVD

USING THE DVD MENUS

1 Press the OPEN/CLOSE button.

The disc loading tray will open.

•

DVD

2 Place a disc into the tray.

Make sure the disc is sitting properly in the correct

recess, with the label side up.

Some DVDs contain their own menus, such as a

guidance menu which describes the contents of the

disc or a selection menu for sound, language and

other customized settings.

1 Press the MENU button.

The DVD menu will appear.

•

2 Select the desired title.

Press the Arrow buttons (L/K/B/s) to change the

setting, and then press the ENTER button.

•

3 Press the PLAY button.

3 Playback will start from the selected title.

The tray will close automatically, and playback

will then start from the first chapter or track of the

disc. You need to press the PLAY button only when

the tray has been closed by pressing the

OPEN/CLOSE button.

•

When you play back the DVD which a title menu

is recorded, the menu may appear on the screen. In

this case, refer to "USING THE TITLE MENU".

4 Press the STOP button to stop play.

- 21 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

RESUMING PLAYBACK FROM

THE POINT WHERE

USING THE TITLE MENU

DVD

PLAYBACK STOPPED

DVD

With a DVD containing a title menu, you can select

desired titles from the menu.

1 Press the STOP button during playback.

Playback will stop, and "STOP"

•

1 Press the TITLE button.

The title menu will appear.

MEMO ON

will appear at the top-right of the

screen and then "MEMO ON" at

the top-left.

•

2 Select the desired title.

Press the Arrow buttons (L/K/B/s) to change the

setting, and then press the ENTER button.

•

2 Press the PLAY button. Playback will start

CALLING UP A MENU SCREEN DUR-

ING PLAYBACK

from the point where the previous playback

session was stopped.

PLAY

For DVDs

Press the MENU button to call up the DVD menu.

Press the TITLE button to call up the title menu.

•

NOTE:

NOTES:

Contents of menus and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

•

The resume function can be reset by pressing the

•

STOP button twice or by opening the disc loading

tray.

The resume function is not available with audio

CDs.

•

PAUSING PLAYBACK OR

DISPLAYING A STILL PICTURE

STEPPING THROUGH FRAMES

DVD

1 Press the PAUSE button during playback.

Playback will pause, with sound

muted.

PAUSE

•

1 Press the PAUSE button while playback is

paused.

PAUSE

The next picture frame is dis-

played with sound muted each

time the button is pressed.

•

2 Press the PLAY button to resume playback.

PLAY

2 Press the PLAY button to resume playback.

PLAY

- 22 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

FAST FORWARD/REVERSE

1 Press the number buttons to enter the

desired track number.

The selected track will be located, and playback

will start.

DVD

•

You can also press the SEARCH MODE button, use

the number or K/L buttons to enter the track number,

1 Press the FWD g or REV h button during

playback. (The sound for DVD is muted.)

and then press the PLAY button.

Pressing the SEARCH MODE but-

ton during playback causes the cur-

rent track number to be displayed in

square brackets.

For DVDs, pressing the FWD g or REV h

button cycles the playback speed in three steps.

For audio CDs, the playback speed is fixed.

•

SEARCH/TRACK

TOTAL TRACKS: 07

TRACK

Start

[

6 ]

REV

Button

FWD D

Button

Ex2

Dx2

Exit

Ex8

Dx8

TRICKS WITH THE SKIP BUTTONS (H, G)

If the SKIP button G is pressed during playback

or while playback is paused, the current track is

skipped and the next track is played. When the

SKIP button H is pressed once, the top of the cur-

rent track is located for replaying. When the SKIP

button H is pressed again while playback is

paused, the previous track is located. Each time the

SKIP button H is pressed while playback is

paused, the disc is searched backward track by

track. Once playback has started, pressing the SKIP

button H locates the top of the current track.

Ex32

Dx32

2 Press the PLAY button to return to normal

playback speed.

SLOW MOTION

DVD

STARTING FROM A DESIRED

TIME COUNT

1 Press the FWD g button while playback is

paused. (Sound remains muted.)

Slow motion mode will be activated.

Pressing the FWD g button cycles the playback

speed in three steps. Select an appropriate speed

while referring to the speed indication on the

screen.

DVD

•

1 Press the SEARCH MODE

SEARCH/TIME

button.

TOTAL TIME 1h23m45s

TIME [ _h__m__s ]

Press the button three times for

DVDs or two times for audio

CDs.

•

FWD D

Button

1/16

Start

Exit

1/8

2 Press the number buttons to set the desired

time count.

SEARCH/TIME

1/2

Example: 1 hour, 23 minutes and

30 seconds

1→+10→+10→3→

+10→+10→+10→0

To enter 0 (zero), press the num-

ber 0 (zero) button or press the B button.

•

TOTAL TIME: 1h23m45s

TIME [1h23m30s]

Start

Exit

2 Press the PLAY button to return to normal

playback speed.

NOTES:

3 Press the PLAY button. Playback will then

Slow playback is not available with audio CDs.

•

start from the set time count.

The reverse of slow playback is not available.

•

NOTES:

Playback from a desired time count is not available

with some discs.

Specific time playback is not available with some

discs or if the unit is in stop mode.

•

STARTING FROM A DESIRED

TRACK

•

- 23 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING FROM A DESIRED

TITLE OR CHAPTER

REPEAT

DVD

1 Press the REPEAT button.

For DVDs

A single title or chapter is played back repeatedly.

Pressing the REPEAT button cycles the display on

the screen as follows.

Press the number buttons to enter the desired chap-

ter number during playback. The selected chapter

will be located within the current title and then

played back.

Title search starts when any number button is

pressed during stop mode.

•

REPEAT

[CHAPTER]

The current chapter is

played back repeatedly.

You can also press the SEARCH MODE button, use

the number or K/L buttons to enter the chapter num-

ber, and then press the PLAY button.

REPEAT

[TITLE]

The current title is

played back repeatedly.

REPEAT

[OFF]

No repeat playback.

For title search, call up the chap-

ter search screen, press the

SEARCH MODE button, and

then operate in the same manner

as above.

SEARCH/CHAPTER

•

TOTAL CHAPTERS: 027

CHAPTER

Start

[

15 ]

If normal playback is performed after REPEAT

CHAPTER has been selected without any chapter

number entered, the first chapter is played back

repeatedly. If the chapter number is changed using

the number buttons or the SKIP buttons (H G)

during playback, the newly selected chapter is

played back repeatedly.

•

Exit

Pressing the SEARCH MODE but-

ton during playback causes the cur-

rent chapter or title number to be

displayed in square brackets.

SEARCH/TITLE

TOTAL TITLES: 07

TITLE

[

5 ]

Start

Exit

NOTE:

Playback from a desired title or chapter is not avail-

able with some DVDs.

For audio CDs

The whole disc or a single track is played back

repeatedly.

•

RANDOM (Audio CD)

Pressing the REPEAT button cycles the display on

the screen through REPEAT TRACK, REPEAT

ALL and REPEAT OFF.

•

REPEAT

[TRACK]

The current track is

played back repeatedly.

1 Press the MODE button in stop mode.

The program setting menu screen will appear.

•

REPEAT

[ALL]

The whole disc is

played back repeatedly.

2 Press the MODE button again.

REPEAT

[OFF]

No repeat playback.

RANDOM

If normal playback is performed after REPEAT

•

Start

Exit

TRACK has been selected without any track num-

ber entered, the first track will be played back

repeatedly. If the track number is changed using

the number buttons or the SKIP buttons (H G)

during playback, the newly selected track is played

back repeatedly.

3 Press the PLAY button. Random playback will

then start.

NOTE:

If the REPEAT button is pressed during program

playback, that program is played back repeatedly.

Program playback is not available during random

playback.

•

NOTE:

Repeat playback is not available with some discs

•

- 24 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

A-B REPEAT

PROGRAM (Audio CD)

DVD

You can define a section to be played back repeatedly.

1 Press the MODE button in stop mode.

The program screen will appear.

•

PROGRAM

[

] / 18 TOTAL 0h 00m 00s

1 Press the A-B REPEAT button during play-

back.

REPEAT

[ A -

]

The starting point (A) will then

be selected.

•

Start,

Delete

Exit

2 Press the number or K/L buttons to enter the

desired track numbers, and then press the

ENTER button to select the settings.

2 Press the A-B REPEAT button again at the

PROGRAM

[1_2 ] / 14 TOTAL 0h 27m 46s

The total playback time for the

selected tracks will appear on the

TOTAL line.

end point (B) of the desired section.

01: 02

02: 04

03: 06

04: 09

05: 01

06: 03

07: 05

08: 07

09: 13

10: 08

11: 12

12: 14

13: 10

14: 11

The selected section will be

played back repeatedly.

REPEAT

[ A - B ]

Start,

Delete

Exit

3 Press the PLAY button.

Playback will start in the programmed order.

The contents of the program are retained after the

program playback ends.

•

3 To exit A-B repeat playback, press the A-B

REPEAT button and set it to OFF.

REPEAT

[ OFF ]

NOTES:

Addition or confirmation of programs is not possi-

•

ble during program playback. You must stop the

current playback before such operations can be car-

ried out.

NOTES:

If B is selected at a point which is earlier than

point A, the previous setting of A is canceled and

the point selected as B will become the setting for

With DVDs, the A-B repeat section can be set only

within the current title.

With audio CDs, the A-B repeat section can be set

across different tracks.

•

Press the CLEAR button to cancel a program. The

most recently entered program will then be deleted.

Up to 20 programs can be stored at any time.

•

PROGRAM

[__] / 14 TOTAL 0h 27m 46s

•

01: 09

02: 03

03: 04

04: 07

05: 01

06: 02

07: 12

08: 10

09: 13

10: 08

11: 01

12: 14

13: 10

14: 11

•

Start,

Delete

Exit

A-B repeat is not available with some scenes in

DVD.

•

Numbers which exceed the number of tracks on the

disc in the tray are not accepted.

Playback from a desired track and random play-

back are not available during program playback.

Program settings are cleared when the power is

turned off or the disc loading tray is opened.

•

- 25 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS

NOTES:

CHANGING THE AUDIO

LANGUAGE OR SOUND MODE

Pressing the K/L buttons may not work on some

•

DVDs with multiple audio languages (e.g. DVDs

which allow audio language setting on the disc

menu). Operation varies between discs, so refer to

the manual accompanying the disc.

DVD

The TV/DVD has a function which allows you to

select the desired audio language and sound mode.

If a desired language is not shown after pressing

the K/L buttons several times, the disc does not

have an audio source in that language.

The audio language resets to the one which has

been selected in the setup mode, every time the

power is turned on or discs are replaced. If that lan-

guage is not available on a disc, a language defined

by the disc is selected.

•

For DVDs

Press the AUDIO button during playback, and

then press the K/L buttons to select the desired

audio language.

The audio language can be changed if multiple lan-

guages are recorded on the DVD being played.

•

The screen display will disappear after about 15

seconds.

If you use DIGITAL AUDIO OUT jack, the sound

mode of audio CDs can not be changed.

•

AUDIO

E N G /8

R E /8

AUDIO

J P N /8

Bon jour

HELLO

For audio CDs

Press the AUDIO button during playback.

Pressing the K/L buttons cycles the sound mode

through STEREO, L-CH and R-CH.

•

Both right and left channels

are active (stereo).

AUDIO

T E R E O

Only the right channel is active.

C H

Only the left channel is active.

AUDIO

- 26 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE SUBTITLE

LANGUAGE

CHANGING THE CAMERA

ANGLE (Multi-Angle Pictures)

DVD

The TV/DVD has a function which allows you to

select the desired language for subtitles.

The TV/DVD has a function which allows you to

select the desired camera angle.

Press the SUBTITLE button during playback, and

then press the K/L buttons to select the desired

subtitle language.

1 Press the ANGLE button during playback.

If the disc contains sequences recorded from differ-

•

ent camera angles, the angle icon (

) will appear

The subtitle language can be changed if the subti-

tles are recorded in multiple languages on the DVD

being played.

•

at the bottom-right of the screen. You can change

the camera angle when the icon appears on the

screen.

The camera angle cannot be changed if the disc

does not contain sequences recorded from different

camera angles.

The subtitle language cannot be changed if the sub-

titles are recorded in a single language on the DVD

being played.

•

SUBTITLE

E N G /8

Subtitle 1

Subtitle 2

2 Press the K/L buttons while the angle num-

ber is shown on the screen.

F R E /8

ANGLE [ 1 ]/8

Angle 1 (default)

SUBTITLE

O F F /8

ANGLE [ 2 ]/8

Angle 2

No subtitles

Angle 8

ANGLE [ 8 ]/8

Bon jour

HELLO

NOTE:

The screen display will disappear after about 15

seconds.

•

Pressing the K/L buttons cycles the subtitle lan-

guage from SUBTITLE 1, SUBTITLE 2 and all

the languages recorded through to OFF.

•

NOTES:

Some discs allow subtitle language setting on the

disc menu. (Operation varies between discs, so

refer to the manual accompanying the disc.)

•

If the desired language is not shown after pressing

the K/L buttons several times, the disc does not

•

have subtitles in that language.

The subtitle language resets to the one which has

•

been selected in the setup mode, every time the

power is turned on or discs are replaced. If that

language is not available on a disc, a language

defined by the disc is selected.

It may take time to display the subtitles in the

selected language.

•

The screen display will disappear after about 15

seconds.

•

- 27 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE ON-SCREEN

DISPLAY

DVD

You can check the information about the disc by

pressing the DISPLAY button on the remote control.

For DVDs

Press the DISPLAY button.

Pressing the DISPLAY button cycles the display on

the screen.

•

• Current title number / total number of titles.

TITLE

TIME

REMAIN

01/04

0h10m25s

0h05m25s

• Elapsed time of the current title.

• Remaining time of the current title.

• Current chapter number / total number of chapters

in the current title.

CHAPTER

TIME

REMAIN

001/010

0h02m25s

0h01m31s

• Elapsed time of the current chapter.

• Remaining time of the current chapter.

• Current language for the sound.

• Current audio format.

AUDIO

1.ENGLISH

DOLBY DIGITAL

6CH

• Current language for the subtitles.

• Selected angle / total number of angles.

• VIRTUAL 3D setting(ON/OFF).

SUBTITLE

ANGLE

VIRTUAL 3D

2.FRENCH

8/8

No display

NOTE:

DOLBY DIGITAL 5.1 Channel is displayed as

"DOLBY DIGITAL 6CH".

•

For audio CDs

Press the DISPLAY button.

Pressing the DISPLAY button toggles the display

on the screen.

•

• Current track number / total track number.

TRACK

TIME

REMAIN

01/04

0h05m25s

0h01m31s

• Elapsed time of the current track.

• Remaining time of the current track.

• Current play mode.

PROGRAM

No display

- 28 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE SETUP ITEMS

DVD

LANGUAGE SETTINGS

4 Press the K/L or number buttons to select a

desired item, and then press the ENTER but-

ton.

1 Press the SETUP button.

The setup screen appears.

SETUP

If OTHER is selected on the AUDIO, SUBTITLE

or DISC MENU setting screen, the COUNTRY

CODE setting screen will appear. Press the number

buttons to enter the desired language (country)

code while referring to the list on page 33, and then

•

1. LANGUAGE

2. VIDEO

3. AUDIO

4. LOCK

5. OTHERS

•

Enter

Exit

press the ENTER button.

SETUP/LANGUAGE

COUNTRY CODE

2 Press the K/L or number buttons to select

[ _ _ _ _ ]

LANGUAGE, and then press the ENTER but-

ton.

SETUP/LANGUAGE

Enter,

Back

Exit

1. AUDIO

2. SUBTITLE

3. DISC MENU

[ENG]

[AUTO]

[ENG]

4. PLAYER MENU [ENG]

5 Press the SETUP button.

Enter,

Back

Exit

The setup mode will be canceled and the ordinary

screen will appear.

•

3 Press the K/L or number buttons to select an

item, and then press the ENTER button.

NOTES:

If the automatically selected language in "AUTO"

for subtitle is same as the selected language for

"AUDIO", the subtitle will not be shown.

If the number buttons are used in steps 2 to 4, the

settings are immediately selected. (You do not need

to press the ENTER button.)

•

SETUP/LANGUAGE

AUDIO

• The original language of each disc will be selected.

• Voice is played back in English.

• Voice is played back in Spanish.

• Voice is played back in French.

1. ORIGINAL

2. ENGLISH

3. SPANISH

4. FRENCH

5. OTHER

•

• You can select other languages for audio playback.

Enter,

Back

Exit

SETUP/LANGUAGE

SUBTITLE

Language Setting for AUDIO and SUBTITLE is

•

Subtitles are shown in the automatically selected

language

1. AUTO

not available with some discs. Then use the

AUDIO and SUBTITLE button. Details are on

pages 26 and 27.

An on-screen display language must be selected

each for the TV mode and DVD mode.

2. ENGLISH

3. SPANISH

4. FRENCH

5. OTHER

• Subtitles are shown in English.

• Subtitles are shown in Spanish.

• Subtitles are shown in French.

Enter,

Back

Exit

• You can select other languages for subtitles.

•

SETUP/LANGUAGE

DISC MENU

• The disc menu is shown in the automatically

selected language.

• The disc menu appears in English.

• The disc menu appears in Spanish.

• The disc menu appears in French.

1. AUTO

2. ENGLISH

3. SPANISH

4. FRENCH

5. OTHER

Enter,

Back

•

You can select other languages for the disc menu.

SETUP/LANGUAGE

PLAYER MENU

1. ENGLISH

2. SPANISH

3. FRENCH

• The on-screen display appears in English.

• The on-screen display appears in Spanish.

• The on-screen display appears in French.

Enter,

Back

- 29 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO SETTINGS

AUDIO SETTINGS

1 Press the SETUP button.

The setup screen will appear.

1 Press the SETUP button.

The setup screen will appear.

SETUP

1. LANGUAGE

2. VIDEO

3. AUDIO

4. LOCK

5. OTHERS

SETUP

•

1. LANGUAGE

2. VIDEO

3. AUDIO

4. LOCK

5. OTHERS

Enter

Exit

Enter

Exit

2 Press the K/L or number buttons to select

AUDIO, and then press the

SETUP/AUDIO

VIDEO, and then press the ENTER button.

ENTER button.

1. DIGITAL OUT

2. VIRTUAL 3D

[OFF]

SETUP/VIDEO

1. TV MODE

2. STILL MODE

[4:3LB]

[AUTO]

Enter,

Back

Exit

Enter,

Back

Exit

3 Press the K/L or number buttons to select an

item, and then press the ENTER button.

3 Press the K/L or number buttons to select an

SETUP/AUDIO

DIGITAL OUT

• Sets the sample rate for playing a disc recorded

with high sound quality.

• When a Dolby Digital decoder is connected.

• When a DTS decoder is connected.

item, and then press the ENTER button.

1. PCM

2. DOLBY DIGITAL [OFF]

3. DTS [OFF]

[48kHz]

SETUP/VIDEO

TV MODE

• Full-height pictures are shown with one or both

sides trimmed.

• Wide screen (full-width) pictures are shown

with black bars at top and bottom.

1. 4:3 PAN&SCAN

2. 4:3 LETTER BOX

3. 16:9 WIDE

Enter,

Back

Exit

• If a wide screen TV is connected.

SETUP/AUDIO

VIRTUAL 3D

Enter,

Back

Exit

1. OFF

2. ON

• To activate the 3D effect.

SETUP/VIDEO

STILL MODE

1. AUTO

2. FIELD

• AUTO is normally selected.

Enter,

Back

Exit

• If pictures are blurred in auto mode.

• For showing motionless pictures at high

resolution in still mode.

3. FRAME

Enter,

Back

Exit

4 Press the K/L or number buttons to select

the desired item, and then press the ENTER

button.

4 Press the K/L or number buttons to select

the desired item, and then press the ENTER

button.

If PCM, DOLBY DIGITAL or DTS is selected on

the DIGITAL OUT setting screen, press the K/L or

number buttons again to select a further item, and

then press the ENTER button.

•

5 Press the SETUP button.

The setup mode will be canceled and the ordinary

screen will appear.

• Audio signals are converted to 48 kHz/16 bit

signals for digital output when playing a DVD

recorded with high sound quality (48 kHz/

20 bit/24 bit, 96 kHz).

SETUP/AUDIO

PCM

•

1. 48kHz

2. 96kHz

• Sound is reproduced at the high quality of

96 kHz when playing a DVD recorded with high

NOTE:

If the number buttons are used in steps 2 to 4, the

settings are immediately selected. (You do not need

to press the ENTER button.)

Enter,

Back

Exit

sound quality (48 kHz/20 bit/24 bit, 96 kHz).

For 48 kHz discs or when 4:3 LETTER BOX

is selected in TV MODE, sound is reproduced

•

at 48 kHz

SETUP/AUDIO

DOLBY DIGITAL

1. OFF

2. ON

•

When a Dolby Digital decoder built-in amplifier

is used.

Enter,

Back

Exit

SETUP/AUDIO

DTS

1. OFF

2. ON

• When a DTS decoder built-in amplifier is used.

Enter,

Back

Exit

- 30 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

PARENTAL LOCK

5 Press the SETUP button.

The setup mode will be canceled and the ordinary

screen will appear.

•

1 Press the SETUP button.

The setup screen will appear.

SETUP

1. LANGUAGE

2. VIDEO

3. AUDIO

•

4. LOCK

5. OTHERS

NOTE:

If the number buttons are used in steps 2 to 4, the

settings are immediately selected. (You do not need

to press the ENTER button.)

Enter

Exit

•

2 Press the K/L or number buttons to select

LOCK, and then press the ENTER button.

SETUP/LOCK

PASSWORD

[ _ _ _ _ ]

This unit employs TruSurround system

of SRS Labs, Inc. as the

1. LEVEL

2. CHANGE PASSWORD

[LEVEL8]

• To set the control level to 1 to 8 or none.

• To cancel the current password and set a

new one on the same screen.

VIRTUAL 3D technology.

Enter,

Back

TruSurround and the

symbol are trademarks of

SRS Labs, Inc. in the United States and selected

foreign countries.

TruSurround technology is incorporated under license

from SRS Labs, Inc.

3 Press the number buttons to enter the 4-digit

password, and then press the ENTER button.

When doing this for the first time, enter any 4 dig-

its. That number will be used as the password from

•

the second time onward.

SETUP/LOCK

PASSWORD

[

]

____

By entering the password, you

can then change the control level

and password settings.

1. LEVEL

2. CHANGE PASSWORD

[LEVEL8]

Enter,

Back

4 Press the K/L or number buttons to select an

item, and then press the ENTER button.

When LEVEL is selected

Press the K/L buttons to select an item from

LEVEL 1 to LEVEL 8 or NONE, and then press

•

the ENTER button.

SETUP/LOCK

PARENTAL LOCK

NONE

LEVEL 8 [PLAY ALL]

LEVEL 7 [NC-17]

LEVEL 6 [R]

LEVEL 5

LEVEL 4 [PG-13]

LEVEL 3 [PG]

LEVEL 2

LEVEL 1 [G]

Enter

When CHANGE PASSWORD is selected

The password entry screen will be displayed and

•

the password which has already been set will be

cleared. The four digits entered in step 3 will then

be set as the new password.

The setup screen will appear.

•

- 31 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROL LEVELS

OTHER SETTINGS

Level 8

•

DVD software of any grade (adult/general/chil-

dren) can be played back.

1 Press the SETUP button.

The setup screen will appear.

SETUP

1. LANGUAGE

2. VIDEO

3. AUDIO

•

Level 7 to 2

Only DVD software intended for general use and

children can be played back.

•

4. LOCK

5. OTHERS

Enter

Exit

Level 1

•

Only DVD software intended for children can be

played back, with those intended for adult and gen-

eral use prohibited.

2 Press the K/L or number buttons to select

OTHERS, and then press the

SETUP/OTHERS

ENTER button.

1. OSD MESSAGE [ON]

2. ANGLE ICON

3. BACKGROUND [BLUE]

[ON]

None

•

Parental lock is canceled.

Enter,

Back

Exit

NOTES:

With some DVDs, it may be difficult to find if they

•

3 Press the K/L or number buttons to select an

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way

that you have set.

If the number buttons are used in steps 2 to 4, the

settings are immediately selected. (You do not need

to press the ENTER button.)

item, and then press the ENTER button.

SETUP/OTHERS

OSD MESSAGE

1. ON

2. OFF

• Selects whether to display messages on the

screen.

•

Enter,

Back

Exit

Record the password in case you forget it.

•

SETUP/OTHERS

ANGLE ICON

1. ON

2. OFF

• Selects whether to display the angle icon.

[Cannot remember your password?]

Reset the setup items and enter the new password

by the following step:

Enter,

Back

Exit

SETUP/OTHERS

BACKGROUND

When the TV/DVD do not run in the DVD mode,

•

1. BLUE

2. GRAY

• Turns the background to blue.

• Turns the background to gray.

and while pressing and holding the STOP button

on the TV/DVD, press the CHANNEL K button

on the TV/DVD.

Enter,

Back

Exit

4 Press the K/L or number buttons to select a

desired item, and then press the ENTER but-

ton.

5 Press the SETUP button.

The setup mode will be canceled and the ordinary

screen will appear.

•

NOTE:

If the number buttons are used in steps 2 to 4, the

•

settings are immediately selected. (You do not need

to press the ENTER button.)

- 32 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

LANGUAGE CODE LIST

DVD

No.

Language

Country code

No.

Language

Country code

Afar

4747

4748

4752

4759

4764

4765

4771

4772

4847

4851

4853

4854

4855

4860

4861

4864

4947

4961

4965

4971

5047

5051

5072

5158

5160

5161

5165

5166

5167

5247

5255

5256

5261

5264

5271

5347

5350

5358

5360

5367

5447

5455

5464

5467

5471

5547

5551

5557

5560

5565

5566

5569

5647

5655

5669

5747

5757

5758

5759

5760

5761

5765

5767

5771

5847

5860

5861

5866

Latvian;Lettish

Malagasy

Maori

5868

5953

5955

5957

5958

5960

5961

5964

5965

5966

5971

6047

6051

6058

6061

6149

6159

6164

6247

6258

6265

6266

6367

6459

6460

6461

6467

6469

6547

6550

6553

6554

6555

6557

6558

6559

6560

6561

6563

6564

6565

6566

6567

6568

6569

6647

6652

6653

6654

6655

6657

6658

6660

6661

6664

6665

6666

6669

6757

6764

6772

6855

6861

6961

7054

7161

7254

7267

Abkhazian

Afrikaans

Amharic

Arabic

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Assamese

Aymara

Azerbaijani

Bashkir

Malay

Byelorussian

Bulgarian

Bihari

Maltese

Burmese

Nauru

Bislama

Nepali

Bengali;Bangla

Tibetan

Breton

Dutch (DUT)

Norwegian

Occitan

Catalan

(Afan)Oromo

Oriya

Panjabi

Corsican

Czech

Welsh

Polish

Danish

Pashto;Pushto

Portuguese

Quechua

Rhaeto-Romance

Kirundi

German (GER)

Bhutani

Greek

English (ENG)

Esperanto

Spanish (SPA)

Estonian

Basque

Romanian

Russian

Kinyarwanda

Sanskrit

Sindhi

Persian

Finnish

Fiji

Sangho

100 Serbo-Croatian

101 Singhalese

102 Slovak

103 Slovenian

104 Samoan

105 Shona

106 Somali

107 Albanian

108 Serbian

109 Siswat

110 Sesotho

111 Sundanese

112 Swedish

113 Swahili

114 Tamil

115 Telugu

116 Tajik

117 Thai

118 Tigrinya

119 Turkmen

120 Tagalog

121 Setswana

122 Tonga

Faroese

French (FRE)

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Hindi

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

Indonesian

Icelandic

Italian (ITA)

Hebrew

Japanese (JPN)

Yiddish

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean (KOR)

Kashmiri

Kurdish

123 Turkish

124 Tsonga

125 Tatar

126 Twi

127 Ukrainian

128 Urdu

129 Uzbek

130 Vietnamese

131 Volapuk

132 Wolof

Kirghiz

Latin

Lingala

Laothian

Lithuanian

133 Xhosa

134 Yoruba

135 Chinese (CHI)

136 Zulu

- 33 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

Problem

Corrective Action

Remote Control Doesn’t Work

Is TV/DVD plugged in?

Power at outlet?

Check batteries in Remote Control.

If outside antenna is being used, check for broken wire.

Check for local interference.

•

Bars On Screen

Picture Distorted or Blurred

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust COLOR control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Picture OK, Sound Poor

No Picture or Sound

Try a new channel, if OK, then possible station trouble.

Is TV/DVD plugged in?

Power at outlet?

Is TV/DVD’S POWER button on?

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Turn off with POWER button and then turn it on after about a minute.

- 34 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

Closed Caption Problem

My TV is showing captions

that are misspelled.

Possible Remedy

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV will not show the text

• Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to the

as being closed captioned but none • actual program so that additional advertising time can be given.

of the captions were displayed.

• Since the decoder cannot read the compressed information,

• captions will be lost.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode or CAPTION

• [OFF].

- 35 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD

If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the

player, consulting the following checklist.

Symptom

No power.

The player does not

respond to the

remote control.

Cause

Loose power plug.

Remedy

Insert the power plug firmly into the wall outlet.

Aim the remote control directly at the sensor on

the TV/DVD.

•

The remote control is not aimed

at the sensor on the TV/DVD.

Obstacles present between the

remote control and the sensor.

The remote control is too far

away from the TV/DVD.

Dead batteries.

Remove the obstacles from the signal path.

Use the remote control within 7m of

the TV/DVD.

Replace the batteries.

Connect the video cables firmly.

Insert a correct video disc that plays on this

TV/DVD.

•

No picture

Loose video connection.

Wrong disc.

Disc cannot be

played

No disc.

Dirty disc.

Insert a disc.

Clean the disc.

•

Disc is placed upside down.

Parental lock is active.

Place the disc correctly, with the label side up.

Cancel the parental lock or change the control

level.

Connect the audio cables firmly.

Turn the power of the audio component on.

No sound

Loose audio connection.

The power of the connected

audio component is off.

Wrong audio output settings.

Wrong input settings on the

connected audio component.

•

Correct the audio output settings.

Correct the input settings on the audio

component.

There are some cases where pictures may be

slightly distorted, which are not a sign of a

malfunction.

•

Distorted picture

Immediately after playing,

press fast forward or in reverse.

Audio or subtitle

language does not

match the setup.

The camera angle

cannot be changed.

The selected language is not

available for audio or subtitles

on the DVD.

The DVD does not contain

sequences recorded from

different camera angles.

The DVD does not contain

audio source or subtitles in the

selected language.

That operation is prohibited by

the TV/DVD or disc.

No malfunction.

•

Audio or subtitle

language cannot be

changed.

"Prohibited icon"

appears on the

screen, prohibiting

an operation.

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

- 36 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

CABINET CLEANING

SERVICING

Wipe the front panel and other exterior surfaces of

the TV/DVD with a soft cloth immersed in luke-

warm water and wrung dry.

Never use a solvent or alcohol. Do not spray insec-

ticide liquid near the TV/DVD. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Should your TV/DVD become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

•

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the player still does not perform properly when it is operated while referring to the relevant sections and to

"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult

your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

•

DISC HANDLING

To clean-off, use a soft cloth.

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

•

Use discs which have the following logos on them.

(Optical audio digital discs.)

•

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

•

Do not use detergent or abrasive cleaning agents.

•

Always store the disc in its protective case when it

is not used.

•

- 37 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

Television system:

NTSC-M

TV Standard

OTHER SPECIFICATIONS

Terminals

Closed caption system: §15.119/FCC

Channel coverage:

Antenna input:

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

VHF:

UHF:

CATV:

2 ~ 13

14 ~ 69

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output

(only DVD):

2 ~13, A ~ W,

W+1 ~ W+84,

A-5 ~ A-1, 5A

181 channel

frequency synthesized

tuning system

Direct access keyboard,

programmable

scan and up/down

1/8” stereo (3.5 mm)

Tuning System:

Channel access:

One pin jack,

500m Vpp (75 ohm)

Analog audio L/R

output (only DVD): RCA connector [ 2

Remote control:

Digital encoded

infrared light system

Operating

temperature:

DVD

5ºC to 40ºC

(41ºF~104ºF)

Power requirements: AC 120V, 60Hz

Power consumption

Product type:

Discs:

Output signal format: NTSC color

Frequency response

(out put jack)

DVD (linear sound): 20 Hz to 22 kHz

(sample rate: 48 kHz)

DVD Player

DVD video, Audio CD

(Maximum):

Picture tube:

Dimensions:

95W

19"

H:19-21/32” (499.5mm)

W:19-7/16” (494mm)

D:20-5/16” (465mm)

44.1 lbs (20kg)

Remote Control Unit with

2"AA"batteries

Owner’s Manual

20 Hz to 44 kHz

(sample rate: 96 kHz)

20 Hz to 20 kHz

Weight:

Accessories:

CD:

Signal-to-noise ratio

(S/N ratio)(out put jack)

CD:

100 dB (EIAJ)

Dynamic range

(out put jack)

DVD (linear sound): 85 dB

CD:

84 dB (EIAJ)

Total distortion factor

CD:

Wow and flutter:

0.07% (EIAJ)

Below the measurement

limitation (+/-0.001%

W PEAK) (EIAJ)

Designs and specifications are subject to change without notice and without our legal obligation.

If there is a discrepancy between languages, the default language will be English.

•

- 38 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

Modo del reproductor DVD:

CONTROLES DE OPERACIÓN Y

SUS FUNCIONES

Visualiza el estado actual en la pantalla del televisor con fines

de comprobación.

24. Botón de modo búsqueda (SEARCH MODE)– Púlselo para

Consulte las figuras 1-3 de las páginas 8 y 9.

localizar el punto deseado.

25. Botón de audio (AUDIO)– Púlselo para seleccionar el modo de

sonido o idioma de audio deseado.

26. Botón de subtítulo (SUBTITLE)– Púlselo para seleccionar un

idioma de subtítulos deseado.

27. Botón de repetición (REPEAT)– Repita la reproducción del

Para utilizarlo como mando a distancia del televisor, pulse el

botón TV del mando a distancia después de seleccionar el

modo del televisor. Los botones de control del televisor se

indican en color azul o blanco.

Para utilizarlo como mando a distancia del reproductor DVD,

pulse el botón DVD del mando a distancia después de selec-

cionar el modo del reproductor DVD. Los botones de control

del reproductor DVD se indican en color amarillo o blanco.

•

disco, título, capítulo o pista actual.

28. Botón de ángulo (ANGLE)– Púlselo para cambiar el ángulo de

la cámara y ver la escena reproduciéndose desde un ángulo

diferente.

1. Bandeja de carga del disco

29. Botón de repetición A-B (A-B REPEAT)– Repite la reproduc-

ción de una sección seleccionada.

2. Toma de entrada de vídeo (VIDEO)– Se conecta a la toma de

salida de vídeo de una videocámara o videograbadora.

30. Botón de retorno (RETURN)– Se utiliza para volver a la

operación anterior.

31. Botón de aceptación (ENTER)– Púlselo para aceptar un ajuste.

32. Botones de flechas–

3. Tomas de entrada de audio izquierda/derecha (AUDIO L/R)–

Se conectan a las tomas de salida de audio de una videocámara

o videograbadora.

4. Botón de alimentación (POWER)– Púlselo para conectar y

Modo del televisor:

desconectar la alimentación.

5. Botones de volumen (VOLUME /L)– Púlselos para controlar

Púlselo para seleccionar un modo de ajuste en los menús que

aparecen en la pantalla del televisor.

Púlselo para seleccionar o ajustar desde un menú particular.

el nivel del sonido del reproductor DVD y del televisor.

6. Botones de canales (CHANNEL /L)– Púlselos para selec-

Modo del reproductor DVD:

cionar los canales memorizados.

7. Ventanilla receptora de señales del mando a distancia

8. Botón de parada (STOP)– Detiene el disco.

9. Botón de rebobinado (REV)– Activa la reproducción en retro-

ceso rápido hasta un punto deseado.

10. Botón de reproducción (PLAY)– Inicia la reproducción del

Se utiliza para hacer ajustes mientras se observa la visual-

ización en la pantalla del televisor.

33. Botón de menú (MENU)– Visualiza los menús del reproductor

DVD y del televisor.

34. Botón de selección (SELECT)– Púlselo para cambiar al modo

del televisor, al modo de entrada exterior o al modo del repro-

ductor DVD.

contenido del disco.

11. Botón de avance (FWD)– Activa la reproducción en avance

rápido hasta un punto deseado.

12. Botón de pausa (PAUSE)– Hace una pausa en el disco actual.

13. Botón de abrir/cerrar (OPEN/CLOSE)– Púlselo para introducir

un disco en la bandeja o para sacarlo de ella.

14. Toma de auriculares (HEADPHONE)– Para conectar unos

auriculares (no suministrados) y escuchar en privado.

15. Botón del televisor (TV)– Púlselo para controlar el televisor.

16. Botón numerados (NUMBER)–

35. Botón de silenciamiento (MUTE)– Púlselo para apagar el

sonido de un programa de televisión. (La visualización del

nivel del sonido cambia de AZUL CLARO a ROJO CLARO.)

Pulse de nuevo este botón o pulse el botón VOL K o L para

reponer el sonido.

36. Botón DVD– Púlselo para controlar el reproductor DVD.

37. Cable de alimentación– Conéctelo a una toma de CA estándar

(120 V/60 Hz).

NOTA: Retire el cable de alimentación del gancho para impedir

que se rompa algún hilo conductor antes de conectar el cable a

una toma de CA.

Modo del televisor:

Pulse dos dígitos para acceder directamente al canal deseado.

No se olvide de pulsar "0" antes de introducir un canal de un

solo dígito.

38. Toma de salida de audio digital COAXIAL– Conéctela a otro

amplificador o descodificador.

39. Toma de salida de audio izquierda/derecha (AUDIO L/R)–

Botón +100–

Conéctela a otro amplificador o descodificador.

Púlselo para seleccionar canales de televisión por cable con un

número igual o superior al 100.

Modo del reproductor DVD:

40. Toma de entrada de antena (ANT.)– Conéctela a una antena,

sistema de televisión por cable o sistema de televisión por

satélite.

Púlselo para introducir el número deseado.

Botón +10–

Púlselo para introducir números iguales o superiores al 10.

PREPARACIÓN PARA LA UTILIZACIÓN

17. Botón del temporizador para dormir (SLEEP)– Pulse el botón

SLEEP para visualizar el temporizador para dormir y activar la

función. La hora de apagado puede determinarse mediante el

número de veces que usted pulse el botón (0, 10, 20, 30, ... 90,

0 minutos).

CONEXIONES DE ANTENA/TELEVISIÓN

POR CABLE

ANTENA COMBINADA DE VHF/UHF

18. Botones de salto (SKIP)– Para saltar capítulo o pistas hasta un

La antena de varilla de VHF/UHF (suministrada) puede desmon-

tarse. Inserte el vástago de la antena en el agujero de la parte supe-

rior trasera del televisor/reproductor DVD. Conecte la antena de

varilla de VHF/UHF o la antena combinada de VHF/UHF en el

terminal ANT. del televisor/reproductor DVD como se muestra en

el diagrama de abajo. Para obtener la mejor recepción, extienda

completamente la antena de varilla de VHF/UHF y haga los

ajustes necesarios. (Evite tocar la sección superior cuando haga el

ajuste.)

punto deseado.

19. Botón de modo (MODE)– Activa el modo de reproducción de

programas o de reproducción aleatoria.

20. Botón de preparación (SETUP)– Púlselo para introducir el

modo de preparación o para cambiar ítems de preparación.

21. Botón de título (TITLE)– Visualiza el menú de títulos.

22. Botón de cancelar (CLEAR)– Cancela un ajuste.

23. Botón del visualizador (DISPLAY)–

Modo del televisor:

Púlselo para visualizar el número del canal en la pantalla. Si lo

presiona de nuevo, el número del canal desaparecerá.

- 39 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTA: Antes de conectar la antena de varilla en el terminal de

antena, compruebe que la clavija no esté doblada. Si lo está,

enderécela como se muestra en la ilustración, y luego conecte la

clavija en el terminal de la antena.

Consulte la figura 8 de la página 12.

CONEXIÓN A UN SISTEMA ESTÉREO

(Para DVD)

Clavija doblada

Consulte la figura 9 de la página 13.

Cable

Clavija

NOTAS:

Asegúrese de desconectar la alimentación de todos los compo-

nentes del sistema antes de hacer conexiones a otro compo-

nente.

(Clavija derecha)

•

(Necesita ser enderezada)

Consulte la figura 4 de la página 10.

Consulte también los manuales de instrucciones del sistema

estéreo y de otros componentes que vayan a ser conectados al

televisor/reproductor DVD.

•

NOTA: La conexión de una antena interior tal vez no ofrezca

siempre una recepción de televisión aceptable.

ANTENAS SEPARADAS DE VHF/UHF

En algunas zonas será necesario utilizar una antena exterior.

CONEXIÓN A UN AMPLIFICADOR

EQUIPADO CON TOMAS DE ENTRADA

DIGITAL, PLATINA MD O PLATINA DAT

(Para DVD)

Consulte la figura 5 de la página 10.

TELEVISIÓN POR CABLE SIN CAJA DE

CONVERSIÓN/DESCODIFICADOR

Utilice esta conexión si su sistema de televisión por cable se

conecta directamente a su televisor/reproductor DVD sin caja de

conversión.

Utilice cables de audio digital coaxial (de venta en el comercio)

para hacer las conexiones de audio.

Consulte la figura 10 de la página 13.

Consulte la figura 6 de la página 11.

NOTAS:

La fuente de audio de un disco del formato de sonido ambiental

Dolby Digital de 5,1 canales no puede grabarse como sonido

digital por una platina MD o DAT.

Asegúrese de desconectar la alimentación de todos los compo-

nentes del sistema antes de hacer conexiones a otro compo-

nente.

Consulte también los manuales de los componentes que vayan a

ser conectados al televisor/reproductor DVD.

En el modo de preparación, ponga DOLBY DIGITAL y DTS en

•

TELEVISIÓN POR CABLE CON CAJA DE

CONVERSIÓN/DESCODIFICADOR O CAJA DE TELE-

VISIÓN POR SATÉLITE

Si sus servicio de televisión por cable le suministra una caja de

conversión, o si usted utiliza un sistema de televisión por satélite,

usted podrá utilizar la conexión básica mostrada aquí.

•

Consulte la figura 7 de la página 11.

APDO. para la salida de audio. Hacer la reproducción en un

televisor/reproductor DVD utilizando ajustes incorrectos puede

generar ruidos, y también puede estropear los altavoces.

Aviso a los instaladores de sistemas CATV:

Este aviso se incluye para que los instaladores de sistemas

CATV tenga en cuenta el Artículo 820-40 del NEC, que pro-

porciona consejos para hacer una conexión apropiada a tierra y,

en particular, especifica que el cable de tierra deberá conectarse

a un sistema de puesta a tierra del edificio tan cerca del punto

de entrada del cable como sea posible.

Cuando ponga DOLBY DIGITAL en APDO. y 3D VIRTUAL

•

en ENC. para la salida de audio en el modo de preparación y

seleccione la fuente de audio en un formato de sonido ambiental

Dolby Digital de 5,1 canales, el audio se silenciará.

CONEXIÓN A UN DESCODIFICADOR

DOLBY DIGITAL O A UN DESCODIFI-

CADOR DTS (Para DVD)

Si utiliza este televisor/reproductor DVD para reproducir en el for-

mato de sonido ambiental Dolby Digital de 5,1 canales o en el for-

mato de sonido ambiental DTS, el televisor/reproductor DVD dará

salida al flujo de datos Dolby Digital o DTS desde su toma de sali-

da de audio digital COAXIAL. Conectando el reproductor a un

descodificador Dolby Digital o DTS, usted podrá disfrutar de un

ambiente más convincente y real, con un sonido ambiental potente

y de alta calidad de tipo profesional como el que puede oírse en

los cines.

INSTALACIÓN DE LAS PILAS

1) Abra la cubierta del compartimiento de las pilas presionando la

cubierta del mando a distancia en el sentido de la flecha.

2) Inserte 2 pilas "AA" en el compartimiento de las pilas, en el

sentido indicado por las

marcas de polaridad (+/-).

3) Vuelva a poner la cubierta.

CONEXIÓN A TOMAS DE ENTRADA

EXTERIOR

Cuando vea un programa grabado en otra fuente (videograbadora o

videocámara), utilice las tomas de entrada de audio/vídeo de la

parte delantera del televisor/reproductor DVD.

Utilice los cables digitales coaxiales de audio (de venta en el com-

ercio) para hacer las conexiones de audio.

Consulte la figura 11 de la página 14.

Conecte las tomas de salida de audio/vídeo de otra fuente a las

tomas AUDIO L/R y VIDEO de este televisor/reproductor DVD.

Y luego pulse el botón SELECT hasta que aparezca "AUX" en la

pantalla.

NOTAS:

Asegúrese de desconectar la alimentación de todos los compo-

•

nentes del sistema antes de hacer conexiones a otro compo-

nente.

NOTA:

Consulte también los manuales de los componentes que vayan a

ser conectados al televisor/reproductor DVD.

Si hace la conexión a un descodificador Dolby Digital, en el

modo de preparación, ponga DOLBY DIGITAL en ENC. para

la salida de audio.

Cuando conecte una videograbadora mono (otra fuente) a este

•

televisor/reproductor DVD, conecte la toma de salida de audio

de la videograbadora mono (otra fuente) a la toma AUDIO L de

este televisor/reproductor DVD. El audio saldrá por los canales

L y R de la misma forma.

Si hace la conexión a un descodificador DTS, en el modo de

•

- 40 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

preparación, ponga DTS en ENC. para la salida de audio.

[FUNCIÓN DE AGREGAR/BORRAR]

A menos que haga la conexión a un descodificador Dolby

Digital o a un descodificador DTS, en el modo de preparación,

ponga DOLBY DIGITAL y DTS en APDO. para la salida de

audio. Hacer la reproducción en un televisor/reproductor DVD

utilizando ajustes incorrectos puede generar ruidos, y también

puede estropear los altavoces.

Cuando ponga DOLBY DIGITAL en APDO. y 3D VIRTUAL

en ENC. para la salida de audio en el modo de preparación y

seleccione la fuente de audio en un formato de sonido ambiental

Dolby Digital de 5,1 canales, el audio se silenciará.

1) Pulse el botón MENU para que la visualización del menú

aparezca en la pantalla del televisor.

2) Pulse el botón de flecha K o L para apuntar a "CANAL

PREP.". Y luego pulse el botón de flecha B.

3) Pulse el botón de flecha B para seleccionar "AGREGAR/BOR-

•

RAR".

4) Utilice el botón de flecha K o L para seleccionar el canal que

desee memorizar o borrar de la memoria.

NOTA: La visualización volverá a la pantalla en unos 10

segundos. Realice la función de "AGREGAR/BORRAR" mien-

tras aparece la visualización en la pantalla.

Fabricado bajo licencia de Dolby Laboratories.

“Dolby” y el símbolo con una doble D son marcas

registradas de Dolby Laboratories. Trabajos confi-

Laboratories. Todos los derechos quedan reservados.

Pulse el botón de flecha B o s para encender el número del

canal en AZUL CLARO si desea agregar el canal a la memoria.

Pulse el botón de flecha B o s para encender el número del

canal en ROJO CLARO si desea borrar el canal de la memoria.

•

5) Pulse el botón MENU para salir del menú.

“DTS” y “DTS Digital Out” son marcas comerciales

de Digital Theater Systems, Inc.

SECCIÓN DEL REPRODUCTOR DVD

REPRODUCCIÓN DE UN DISCO

SECCIÓN DEL TELEVISOR

Para empezar

1) Conecte la alimentación del amplificador o de cualquier otro

componente que esté conectado al televisor/reproductor DVD.

(Cambie el sistema de entrada para que se adapte al

televisor/reproductor DVD, y compruebe que el volumen del

sonido sea el correcto.)

PREPARACIÓN PARA LA UTILIZACIÓN

Para empezar

1) Conecte el cable de alimentación a una toma de CA estándar.

NOTA: Si aparecen algunos dígitos en la esquina de la pantalla,

2) Pulse el botón POWER.

pulse el botón POWER sin desconectar el cable de alimentación.

La alimentación se conectará.

3) Pulse el botón SELECT del mando a distancia hasta que "DVD"

aparezca en la pantalla. Luego pulse el botón DVD.

•

2) Pulse el botón POWER para encender el televisor/reproductor

DVD.

3) Pulse el botón SELECT del mando a distancia hasta que el

número del canal o "TV" aparezca en la pantalla.

Luego pulse el botón TV.

REPRODUCCIÓN DE UN DVD VIDEO O

UN CD DE AUDIO

SELECCIÓN DE IDIOMA

Si desea cambiar el idioma del menú en pantalla, siga el proced-

imiento siguiente.

1) Pulse el botón MENU para que la visualización del menú

aparezca en la pantalla del televisor.

2) Pulse el botón de flecha K o L para apuntar a "LANGUAGE".

3) Seleccione "ENGLISH" = inglés, "ESPAÑOL" o FRANÇAIS =

francés utilizando el botón de flecha B o s.

4) Pulse el botón MENU para salir del menú.

NOTA: El idioma de la visualización en pantalla deberá selec-

cionase para el modo del televisor y el modo de DVD.

DVD

1) Pulse el botón OPEN/CLOSE.

La bandeja del disco se abrirá.

2) Ponga un disco en la bandeja.

•

Asegúrese de que el disco esté bien colocado en la bandeja, con

la cara de la etiqueta hacia arriba.

•

3) Pulse el botón PLAY.

•

La bandeja se cerrará automáticamente, y la reproducción

empezará desde el primer capítulo o la primera pista del disco.

Usted necesitará pulsar PLAY sólo cuando la bandeja haya sido

cerrada pulsando el botón OPEN/CLOSE.

Cuando reproduzca un DVD que tenga grabado un menú de

títulos, el menú podrá aparecer en la pantalla. En este caso, con-

sulte "UTILIZACIÓN DEL MENÚ DE TÍTULOS".

PREAJUSTE DE CANALES

Para preajustar un canal o cambiar un canal preajustado, siga el

procedimiento siguiente.

1) Pulse el botón MENU para que la visualización del menú desa-

parezca de la pantalla del televisor.

•

4) Pulse el botón STOP para detener la reproducción.

NOTAS:

Durante la operación puede aparecer un "icono de prohibición"

2) Pulse el botón de flecha K o L para apuntar a "CANAL

PREP.". Y luego pulse el botón de flecha B.

3) Pulse el botón de flecha K o L para apuntar a "AUTOPRESE-

LEC.". Luego, pulse el botón de flecha B.

El sintonizador explora y memoriza todos los canales activos en su

área.

•

en la parte inferior derecha de la pantalla del televisor, avisán-

dole que el televisor/reproductor DVD o el disco han encontra-

do una operación prohibida.

Si un disco está sucio o tiene rayas, las imágenes pueden apare-

•

cer distorsionadas y la operación de reproducción tal vez se

detenga. En tales casos, limpie el disco y desenchufe el cable de

alimentación, y luego vuelva a conectarlo antes de reanudar la

reproducción.

Con DVDs que utilicen algunos títulos para reproducir señales

de programas, la reproducción tal vez empiece desde el segundo

título, o puede que omita estos títulos.

Las funciones relacionadas con el DVD se activan sólo en el

modo DVD.

Para poner en funcionamiento el reproductor DVD, pulse el

botón PLAY u OPEN/CLOSE.

El televisor distingue entre los canales de televisión estándar y

los canales de televisión por cable.

•

Cuando termine la acción de AUTOPRESELEC., el canal mem-

orizado más baja volverá a aparecer en la pantalla.

•

Cuando pulse el botón de flecha K o L después de seleccionar

AUTOPRESELEC., el sintonizador se detendrá en los canales

memorizados solamente.

•

El televisor puede reconocer si los canales de televisión son

•

CATV por las condiciones de la recepción. En este caso, intente

de nuevo la acción de AUTOPRESELEC. en condiciones de

recepción fina.

- 41 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

UTILIZACIÓN DE LOS MENÚS DE DVD

DVD

Algunos DVDs tienen sus propios menús como, por ejemplo, un

menú guía que describe el contenido del disco o un menú de selec-

ción para seleccionar el sonido, el idioma y otros ajustes personal-

izados.

1) Pulse el botón MENU.

El menú DVD aparecerá.

2) Seleccione el título deseado.

•

Pulse los botones de las flechas (K/L/B/s) para cambiar el

ajuste, y luego pulse el botón ENTER.

•

3) La reproducción empezará desde el título seleccionado.

UTILIZACIÓN DEL MENÚ DE TÍTULOS

DVD

Con un DVD que tenga un menú de títulos, usted podrá selec-

cionar los títulos deseados en el menú.

1) Pulse el botón TITLE.

El menú de títulos aparecerá.

2) Seleccione el título deseado.

•

Pulse los botones de las flechas (K/L/B/s) para cambiar el

ajuste, y luego pulse el botón ENTER.

•

RECUPERACIÓN DE UNA PANTALLA DE MENÚS

DURANTE LA REPRODUCCIÓN

Para DVDs

Pulse el botón MENU para recuperar el menú del DVD.

Pulse el botón TITLE para recuperar el menú de títulos.

•

NOTA:

El contenido de los menús y las operaciones con menús corre-

spondientes pueden cambiar según los discos, Consulte el man-

ual entregado con el disco para conocer detalles.

•

- 42 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

- 43 -

0C28

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as fol-

lows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original

retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.

LABOR:

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail

purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be

required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was

attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any product not pur-

chased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage

which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage

which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commer-

cial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY

COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT

OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS

PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL

OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MER-

CHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRE-

SENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER.

THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.

WHEN YOU ARE RETURNING THE PRODUCT FOR SERVICE TO THE FACTORY SERVICE CENTER, PLEASE CON-

TACT THE FUNAI SERVICE DEPARTMENT TO RECEIVE A R.A. (REPAIR AUTHORIZATION) NUMBER PRIOR TO

SHIPPING. ANY POSTAGE, INSURANCE AND SHIPPING COST, INCURRED IN PRESENTING OR SENDING YOUR SYLVA-

NIA PRODUCT FOR SERVICE ARE SHIPPER’S RESPONSIBILITY.

CAREFULLY PACK WITH PROPER PACKING MATERIALS, PREFERABLY IN THE ORIGINAL CARTON AND IF NEEDED

DOUBLE BOX IT.

ATTACH WRITTEN DOCUMENTATION DETAILING THE COMPLAINT, TO THE OUTSIDE OR INSIDE OF THE CAR-

TON.

THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF

PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM

STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION

WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure, please call 1-800-968-3429 or

write to the following:

FUNAI CORPORATION

Factory Service Center

100 North Street; Teterboro, NJ 07608

Tel :1-800-968-3429

Printed in China

0EMN01723

TD200UA * * * * *

Download from Www.Somanuals.com. All Manuals Search And Download.

Sennheiser Headphones SET50TV User Manual
Sharp CRT Television PG MB66X User Manual
Shindaiwa Trimmer 81372 User Manual
Sony CRT Television KDL 32M3000 User Manual
Sony Speaker SSM F400H User Manual
Sony Stereo Receiver STR DH740 User Manual
Sony TV VCR Combo 413 User Manual
Sterling Plumbing Hot Tub 71101122 User Manual
Strong Pools and Spas Hot Tub Grand Cayman Spa User Manual
Sylvania DVD VCR Combo DVC860E User Manual