Sylvania TV DVD Combo 6513DD 6519DD User Manual

OWNER’S

MANUAL

COLOR TV/DVD

6513DD (13 inch)

6519DD (19 inch)

13” MODEL ILLUSTRATED

This Owner’s Manual is made of

recycled paper.

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®is

a U.S. registered mark.

If you need additional assistance for set-up or operating after

reading owner’s manual, please call TOLL FREE : 1-800-968-3429.

Or visit our WEB SITE at http://www.funai-corp.com

^{Download from Www.So}P^ml^aeⁿa^uas^lse^.cr^oe^ma^.d^Allb^Me^afⁿo^uar^le^{s S}u^es^ai^rcn^hg^Anth^di^Ds^oweⁿq^lou^ai^dp^.ment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

12.Power-Cord Protection-Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying par-

ticular attention to cords at plugs, convenience receptacles,

and the point where they exit from the appliance.

19.Damage Requiring Service-Unplug this TV/DVD from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/DVD.

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/DVD, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

c. If the TV/DVD has been exposed to rain or water.

d. If the TV/DVD does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/DVD to its normal operation.

e. If the TV/DVD has been dropped or damaged in any way.

f. When the TV/DVD exhibits a distinct change in perfor-

mance-this indicates a need for service.

14.Lightning-For added protection for this TV/DVD receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/DVD due to lightning and

power-line surges.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

21.Safety Check-Upon completion of any service or repairs to

this TV/DVD, ask the service technician to perform routine

safety checks to determine that the TV/DVD is in proper

operating condition.

22.Heat-This TV/DVD product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/DVD through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/DVD.

18.Servicing-Do not attempt to service this TV/DVD yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to qualified

service personnel.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LASER SAFETY

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable

and can be reused. Please dispose of any materials

in accordance with your local recycling regula-

tions.

Batteries should never be thrown away or inciner-

ated but disposed of in accordance with your local

regulations concerning chemical wastes.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

LOCATION

SUPPLIED ACCESSORY

For safe operation and satisfactory performance of

your TV/DVD, keep the following in mind when

selecting a place for its installation:

Remote Control Unit

(PART NO.: NE207UD)

•

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

2 AA Batteries

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top and bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

Indoor Antenna

(13” model only supplied)

19” model not supplied)

PART NO. (0EMN00673 or

0EMN01599 or 0EMN01755)

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/DVD near strong magnetic fields.

Avoid moving TV/DVD to locations where temper-

•

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings

ature differences are extreme.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

: Description refers to TV operation (in the TV mode).

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

DVD-V

: Description refers to playback of DVD video discs

(in the DVD mode).

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

: Description refers to playback of audio CDs

(in the DVD mode).

Do not put your fingers or objects into the

TV/DVD disc loading tray.

•

MP3

Do not place anything directly on top of the unit.

•

: Description refers to playback of MP3 discs

(in the DVD mode).

QUICK

WARNING

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a TV/DVD

which has moisture, it may damage the DVD and

TV/DVD. Therefore when the condensation occurs

inside the unit, turn POWER on and allow at least 2

hours for the unit to dry out.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

C SEARCH FUNCTION . . . . . . . . . . . . . . . . . .23

TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . .23

TITLE / CHAPTER SEARCH . . . . . . . . . . . . .23

TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .23

MARKER SETUP SCREEN . . . . . . . . . . . . . .23

OPERATING CONTROLS AND FUNCTIONS . . .8

INSTALLING THE BATTERIES . . . . . . . . . . .9

C SPECIAL PLAYBACK FUNCTION . . . . . . . .24

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .24

RANDOM PLAYBACK . . . . . . . . . . . . . . . . .24

C PREPARATION FOR USE . . . . . . . . . . . . . . .10

ANTENNA/CABLE CONNECTIONS . . . . . . .10

INDOOR ANTENNA . . . . . . . . . . . . . . . . . . .10

CONNECTING TO EXTERNAL INPUT JACKS .11

C PLAYING A MP3 DISC . . . . . . . . . . . . . . . . . .25

MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . .25

TRACK SELECTION . . . . . . . . . . . . . . . . . . .25

PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . .25

RANDOM PLAYBACK . . . . . . . . . . . . . . . . .25

CONNECTING TO A STEREO SYSTEM . . . .12

CONNECTING TO AN AMPLIFIER

EQUIPPED WITH DIGITAL INPUT JACKS,

MD DECK OR DAT DECK (for DVD only) . .12

CONNECTING TO A DOLBY DIGITAL

DECODER (for DVD) . . . . . . . . . . . . . . . . . . .13

C CHANGING THE SETTINGS . . . . . . . . . . . .26

SUBTITLE LANGUAGE . . . . . . . . . . . . . . . .26

AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . .26

STEREO SOUND MODE . . . . . . . . . . . . . . . .26

CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . .26

BLACK LEVEL SETTING . . . . . . . . . . . . . . .26

VIRTUAL SURROUND . . . . . . . . . . . . . . . . .26

TV SECTION

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .14

CHANNEL SET UP FOR THE FIRST TIME . .14

DELETING (OR ADDING) CHANNEL . . . . .14

CHANNEL SET UP AGAIN . . . . . . . . . . . . . .15

SELECTING THE LANGUAGE . . . . . . . . . . .15

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .16

WATCHING A TV PROGRAM . . . . . . . . . . . .16

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .16

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .16

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .17

CLOSED CAPTION SYSTEM . . . . . . . . . . . .17

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .18

C THE ON-SCREEN INFORMATION . . . . . . .27

C CHANGING THE DVD SETUP ITEMS . . . .28

LANGUAGE SETTING . . . . . . . . . . . . . . . . .28

DISPLAY SETTING . . . . . . . . . . . . . . . . . . . .29

AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .29

PARENTAL CONTROL . . . . . . . . . . . . . . . . .30

C TROUBLESHOOTING GUIDE . . . . . . . . . . .31

DVD SECTION

C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .20

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .33

PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .20

DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .20

DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .33

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .34

C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .21

BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . .21

GENERAL FEATURES . . . . . . . . . . . . . . . . . .21

DISC MENU . . . . . . . . . . . . . . . . . . . . . . . . . .21

TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . .21

RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

STEP BY STEP PLAYBACK . . . . . . . . . . . . .22

FAST FORWARD/REVERSE SEARCH . . . . .22

SLOW FORWARD / SLOW REVERSE . . . . .22

ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

FEATURES

TV Mode

DVD Mode

¡Dolby Digital sound

181 channel capability PLL frequency synthesiz-

er tuner with direct station call

(A converter may be necessary to view scrambled

cable channels.)

Infrared remote control

Trilingual on screen menu display selectable in

English, Spanish, or French

•

This player can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby Digital

decoder.

¡Still/fast/slow/step playback

Various playback modes are available including still pic-

tures, fast forward/reverse, slow motion and step frames.

•

¡Random playback for audio CD and MP3

This player can shuffle the order of tracks to play them in

random order.

¡Sleep Timer

he Sleep Timer function enables you to shut off the power

without pressing POWER after a desired time period.

¡Program playback for audio CD and MP3

You can program the order of tracks to play them in any

desired order.

¡Closed Caption Decoder

You may view specially labeled (cc) TV programs,

movies, news, etc. with either a dialogue caption or text

display added to the program.

¡DVD menus in a desired language

You can display DVD menus in a desired language, if

available on a DVD.

¡Auto Shut Off Function

If there is no air signal input from the antenna terminal and

no operation for 15 minutes, the TV will turn itself off

automatically.

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no input

from the player for five minutes in the stop mode. When

the screen saver program is activated for 15 minutes, the

power is automatically turned off.

¡V-CHIP

Enables parents to prevent their children from watching

inappropriate material on TV.

¡Subtitles in a desired language

You can select a desired language for the display subtitles,

if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc contains

sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound mode,

if different languages and modes are available on a disc.

¡Parental lock

You can set the control level to limit playback of discs

which may not be suitable for children.

¡Automatic detection of discs

This player automatically detects if the loaded disc is

DVD, audio CD or MP3 on disc.

¡On-screen display

Information about the current operation can be displayed

on a TV screen, allowing you to confirm the currently

active functions (such as program playback), on the TV

screen using the remote control.

¡Search

Chapter search / Title search / Track search / Time search

¡Repeat

Chapter / Title / Track / Group / All / A-B

¡Zoom

Magnified screen can be displayed.

¡Marker

The part designated by user can be called back.

¡Resume Play

User can resume to playback from the part at which the

play was stopped.

¡Virtual Surround

¡Bit rate indication

¡DRC (Dynamic range control)

You can control the range of sound volume.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

OPERATING CONTROLS AND FUNCTIONS

This manual covers 13 and 19 . The operation of the two models are exactly the same except

the appearance. 13 model is illustrated in this manual.

[Fig. 1]

TV/DVD FRONT PANEL

AUDIO

POWER

VOLUME

CHANNEL

VIDEO

STOP

SKIP

PLAY SKIP

PAUSE

OPEN/CLOSE HEADPHONE

9 10 11 12 13 14

8. STOP Button [page 21]

Stops operation of the disc.

[Fig. 2]

REMOTE CONTROL

9.SKIP H Button [page 23]

Plays back from the beginning of the current

chapter or track.

SEARCH (REV) E Button (Front Panel)

[page 22]

OPEN/

POWER PICTURE SELECT

During playback or in the pause mode, press and

hold button down for a few seconds to change

reverse playback speed.

CH.

10. PLAY Button [page 21]

Starts playback of the disc contents.

Press to change to DVD mode when TV mode.

SLEEP

+100

VOL.

+10

11. SKIP G Button [page 23]

Plays back from the beginning of the next chapter

or track.

SKIP

ZOOM

MUTE

PLAY

STOP

SEARCH (FWD) D Button (Front Panel)

[page 22]

During playback or in the pause mode, press and

hold button down for a few seconds to change for-

ward playback speed.

REV

FWD

DISC

PAUSE SLOW

DISPLAY

ENTER

12. PAUSE Button [page 22]

SETUP

TITLE

RETURN

Pauses the current disc operation.

13. OPEN/CLOSE Button [page 21]

Press to insert discs into or remove them from the

tray.

CLEAR SEARCH MODE REPEAT

A-B

AUDIO SUBTITLE ANGLE

MODE

14. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

15. MODE Button [pages 24-26]

Activates program playback or random playback mode

when playing CDs or MP3.

1. Disc loading tray

2. VIDEO input Jack [page 11]

16. Number Button

Connect to the video output jack of a video

camera or VCR.

TV Mode: [page 14]

Press two digits to directly access the desired chan-

nel.

3. AUDIO L/R input Jacks [page 11]

Connect to the audio output jacks of a video

camera or VCR.

Remember to press a "0" before a single digit chan-

nel.

4. POWER Button [page 14]

+100 Button–

Press to select cable channels which are equal or

greater than number 100.

Press to turn the power on and off.

5. VOLUME K/L (VOL. m/n) Buttons

Press to control the volume level for the DVD and TV.

DVD Mode: [page 23]

6. CHANNEL K/L (CH. K/L) Buttons [page 14]

Press to select memorized channel.

Press to change to TV mode when DVD mode.

Press to enter the desired number.

+10 Button–

Press to enter the desired numbers which are equal

or greater than number 10.

7. Remote Sensor Window

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

[Fig. 3]

TV/DVD REAR VIEW

ANT.

AUDIO OUT

COAXIAL

32. Arrow Buttons

17. SLEEP Button [page 17]

TV Mode: [page 14]

Press SLEEP to display the sleep timer and start the

function. The shut off time can be determined by the

number of times you press this button. (0, 30, 60,

90, or 120 minutes)

Press to select a setting mode from the menu on the

TV screen.

Press to select or adjust from a particular menu.

DVD Mode: [page 21]

18. REV h Button [page 22]

Use when making settings while watching the

display on a TV screen.

Press to view the DVD picture in fast reverse motion.

Press PAUSE, then press this button to begin slow

motion playback. Press this button repeatedly to change

the reverse speed of slow motion.

33. DISC MENU Button [page 21]

Displays the menus in the DVD.

34. SELECT Button [pages 11, 21]

Press to change to TV mode, external input mode or

DVD mode.

FWD g Button [page 22]

Press to fast forward the Disc. Press PAUSE, then

press this button to begin slow motion playback. Press

this button repeatedly to change the forward speed of

slow motion.

NOTE: When you select the DVD mode by this

button, press PLAY or OPEN/CLOSE first.

Otherwise, the DVD features are not operated.

19. ZOOM Button [page 22]

Expands the picture to fill the entire screen.

20. SETUP Button [pages 14,28-30]

Press to enter or exit the TV menu or DVD setup

mode.

35. MUTE Button

Press MUTE to turn off the sound

portion of the TV program. (Volume level display

turns LIGHT RED from LIGHT BLUE.) Press

MUTE again or press VOL. m or n to restore

sound.

21. TITLE Button [page 21]

Displays the title menu.

22. CLEAR Button [pages 23-25]

36. PICTURE Button [page 16]

Resets a setting.

Press to enter picture adjustment mode.

23. DISPLAY Button

37. Power cord

TV Mode:

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook to

avoid breaking a wire before you connect to

a standard AC outlet.

Press to display the channel number on the screen.

If you press it again, the channel number will disap-

pear.

DVD Mode: [page 27]

Displays the current status on the TV screen for

checking purposes.

38. AUDIO L/R output Jack

Connect to the analog audio input of an external

amplifier or decoder.

24. SEARCH MODE Button [page 23]

39. COAXIAL digital audio out Jack (DVD Audio

Only)

Press to locate a desired point.

25. AUDIO Button [page 26]

Press to select a desired audio language or sound

mode.

Connect to the digital input of an external

amplifier or decoder.

40. ANT. in Jack

26. SUBTITLE Button [page 26]

Connect to an antenna, cable system, or satellite sys-

tem.

Press to select a desired subtitle language.

27. REPEAT Button [page 24]

Repeats playback of the current disc, title, chapter

or track.

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing the

cover on the remote unit in the direction of the arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

28. ANGLE Button [page 26]

Press to change the camera angle to see the sequence

being played back from a different angle.

29. REPEAT A-B Button [page 24]

Repeats playback of a selected section.

30. RETURN Button [page 26]

3)Replace the cover.

Returns to the previous operation.

31. ENTER Button [pages 14, 21]

Press to accept a setting.

NOTES

¡Do not mix alkaline and manganese batteries.

¡Do not mix old and new batteries.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

From Cable System or

Satellite Box or

Cable Box

(Not supplied)

VHF/UHF Antenna

(Not supplied)

OUT

Satellite Dish

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

NT.

OUT

OAXIAL

VHF/UHF

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied)

Flat twin-lead cable

[Fig. 4]

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

Bent pin

NOTE:

Before plugging the an antenna into the ANT. IN jack of the TV/DVD, check that

the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin

into the ANT. IN jack of the TV/DVD.

Cable

Plug

(Needs to be straightened)(Straight pin)

VHF/UHF COMBINED ANTENNA

A VHF UHF 75 ohm combination antenna can be

connected to ANT terminal.

CABLE WITH CONVERTER/DESCRAM-

BLER BOX OR SATELLITE BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown here.

Channel selection must be made with the converter

box or satellite box. This means that channels cannot

be changed using the TV/ DVD Remote Control.

TO VIEW A SCRAMBLED/UNSCRAMBLED

CHANNEL

1.Set the TV/DVD channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor

antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/DVD without a converter box.

Use the TV/ DVD Remote Control to select channels.

2.Select the channel to view at your Cable Converter

Box or Satellite Box.

INDOOR ANTENNA

Indoor Antenna

(supplied with 13”

model only)

The Indoor Antenna (supplied with 13” model only) is detachable. Insert the stem

of the antenna into the hole on the upper-back portion of the TV/DVD. Connect the

Indoor Antenna to the TV/DVD as shown in the diagram. For the best reception,

fully extend the Indoor Antenna and make the necessary adjustments. (Avoid touch-

ing the top section when adjusting.)

NOTE:

The connection of an Indoor antenna may not always give acceptable TV reception.

ANT.

OAXIAL

[Fig. 5]

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONNECTING TO EXTERNAL INPUT JACKS

When you watch a program recorded on an another

[Front of the TV/DVD]

source (VCR or video camera), use the audio/video

input jacks on the front of the TV/DVD.

Connect the audio/video output

VIDEO

AUDIO

[Another source]

To the audio

output jacks

jacks of another source to the

AUDIO L/R and VIDEO jacks of

this TV/DVD. Then press SELECT

until "AUX" appears on the screen.

NOTE:

AUX

Audio/Video

cables

VIDEO

AUDIO

(not supplied)

When you connect a monaural VCR (another

•

source) to this TV/DVD, connect the Audio output

jack of the monaural VCR (another source) to the

AUDIO L jack of this TV/DVD. The audio will

output in both L and R channel equally.

etc.

To the video

output jack

[Fig. 6]

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONNECTING TO A STEREO SYSTEM

NT.

OUT

OAXIAL

Stereo system

AUDIO OUT

COAXIAL

To Right (red) and Left (white)

AUDIO OUT jacks

To ANALOG AUDIO INPUT jacks

[Fig. 7]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for your stereo system and any other components to be connected to the

TV/DVD.

•

The monaural sound is output from the stereo system when the TV/DVD is in the TV mode.

•

CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL

INPUT JACKS, MD DECK OR DAT DECK (for DVD only)

Use an audio coaxial digital cable available at retail for the audio connections.

Amplifier equipped with digital

input jacks, MD deck,

DAT deck, etc.

ANT.

AUDIO OUT

COAXIAL

To COAXIAL DIGITAL

AUDIO INPUT jack

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

(only DVD AUDIO OUT)

[Fig. 8]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a TV/DVD using incorrect set-

tings may generate noise distortion, and may also damage the speakers. (See page 29 to set DOLBY

DIGITAL to OFF.)

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If using this TV/DVD to play a DVD disc in a 5.1 channel Dolby Digital surround format, the TV/DVD out-

puts a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the player up to

a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality

surround sound as enjoyed in movie theaters.

Use audio coaxial digital cables available at retail for the audio connections.

ANT.

Center

speaker

AUDIO OUT

Front speaker

(left)

Front speaker

(right)

COAXIAL

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

Dolby Digital decoder

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 9]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD.

If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.

(See page 29 to set DOLBY DIGITAL to ON.)

•

Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup

mode. Playing a TV/DVD using incorrect settings may generate noise distortion, and may also damage the

speakers.

•

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TV SECTION

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just

select the TV/DVD channel selector to the output channel of the cable box or satellite box (Ex CH3). Then

select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

FIRST TIME

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

1 Plug in the TV/DVD power cord

Plug the TV/DVD power cord into a

standard AC outlet.

NOTE:

- TV SETUP -

1 Select “CHANNEL SET UP”

Press SETUP on the remote control.

Press K or L to point to “CHAN-

NEL SET UP”.

If some digits appear in the corner of

the screen, press POWER without

unplugging the power cord.

•

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

2 Turn on the TV/DVD

Press POWER to turn on the TV/DVD.

Then, press ENTER.

2 Select “ADD/DELETE CH”

Press K or L to point to

“ADD/DELETE CH”.

– CHANNEL SET UP –

ADD / DELETE CH (TV)

AUTO PRESET

3 Select the On Screen

Language

Press K or L to point to “LAN-

GUAGE”.

– SET UP –

LANGUAGE

Then, press ENTER.

[ENGLISH] ESP

FRA

AUTO PRESET

Then, press ENTER to select

“ENGLISH” or “ESP”=Spanish or

“FRA” =French. “[ ]” indicate the selected language.

3 Enter the desired channel number

Press K or L until your desired

channel number appears. (You can

also use Number or CH. K/L to

enter it.) (Example: CH8)

– SET UP –

4 Begin auto preset

Press K or L to point to “AUTO

ADD / DELETE

LANGUAGE

[ENGLISH] ESP

FRA

PRESET”. Then, press ENTER.

The tuner scans and memorizes all

active channels in your area.

AUTO PRESET

4 Delete (or add) it from (into) memory

Press ENTER. The channel number changes to light

red. The channel is deleted from memory.

NOTES:

The TV/DVD distinguishes between standard TV

channels and cable(CATV) channels.

•

Added channel: Light blue.

Deleted channel: Light red.

The TV/DVD may memorize TV channels as

CATV channels if reception conditions is poor. If

this happens, try AUTO PRESET action again

when reception conditions are better. See “CHAN-

NEL SET UP AGAIN” on page 15.

•

To delete another channel, repeat steps [3] and [4].

If you press ENTER again, the channel is memo-

rized again.

•

5 After scanning

5 Exit the channel setup mode

Press SETUP on the remote control to returns to TV

mode.

NOTE: To confirm that channel(s) has been deleted

or added, press CHANNEL(CH.) K or L.

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with Number or

CHANNEL(CH.) K or L.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CHANNEL SET UP AGAIN

- TV SETUP -

1 Select “CHANNEL SET UP”

Press SETUP on the remote control.

Press K or L to point to “CHAN-

NEL SET UP”.

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Then, press ENTER.

2 Begin auto preset

– CHANNEL SET UP –

Press K or L to point to “AUTO

PRESET”. Then, press ENTER.

The tuner scans and memorizes all

the active channels in your area.

NOTES:

ADD / DELETE CH (TV)

AUTO PRESET

The TV/DVD distinguishes between standard TV

channels and cable(CATV) channels.

•

The TV/DVD may memorize TV channels as

CATV channels if reception conditions is poor. If

this happens, try AUTO PRESET action again

when reception conditions are better.

•

3 After scanning

The tuner stops on the lowest memorized channel.

SELECTING THE LANGUAGE

NOTE: This function effects only the language on

the screen menu and not the audio source.

- TV SETUP -

1 Select “LANGUAGE”

Press SETUP on the remote control.

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press K or L to point to “LAN-

GUAGE”.

Then, press ENTER to select

“ENGLISH” or “ESPAÑOL”=

Spanish or “FRANÇAIS”= French.

2 Exit the Language mode

Press SETUP on the remote control to return to TV

mode.

NOTE: If Spanish or French is selected accidentally,

1)Press SETUP on the remote control.

2)Press K or L to point to “IDIOMA [ESPAÑOL]”

or “LANGAGE” [FRANÇAIS].

3)Press ENTER to select your desired language.

4)Press SETUP to exit.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/DVD’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

1 Turn on the TV/DVD

Press POWER to turn on the TV/DVD.

2 Select the channel number

Press CHANNEL(CH.) K or L to select your desired

channel number or press Number on the remote con-

trol.

Make sure ...

TV/DVD power must be turned on.

•

Note for using the Number on the remote control:

¡When selecting cable channels which are higher

than 99, press +100 first, then, press the last two

digits. (Example: to select channel 125, first press

“+100” then press “2” and “5”).

1 Select “PICTURE CONTROL”

Press PICTURE on the remote control.

¡You must precede single-digit channel numbers

with a zero (For example: 02, 03, 04 and so on).

Remember:

¡If the TV/DVD is connected to a cable box or

satellite box, the TV/DVD must be on CH3 or

CH4, then the channel to be viewed must be select-

ed on the cable box or satellite box.

2 Select item you want to adjust

Press K or L until desired control is displayed.

BRIGHT

CONTRAST

COLOR

TINT

BRIGHT

–

P +

SHARPNESS

3 Adjust sound

Press VOLUME(VOL.) or to

3 Adjust the picture control

adjust the volume.

Press B or s to adjust to your desired level within

VOLUME 20

5 seconds.

NOTE:

At step 3, the picture adjustment display will disap-

If you press the CHANNEL(CH.) o or p in the

DVD mode, you can change the TV channels.

Even if you turn off the TV/DVD in the DVD

mode, when you turn it on again, it will go into the

TV mode.

•

pear from the TV screen after about 5 seconds

unless you press any buttons, even though you may

not be finished. In this case, repeat from step [1].

BRIGHT

to decrease

brightness

to decrease

contrast

to increase

brightness

to increase

contrast

DEGAUSSING

Magnetism from nearby appliances and speakers

might affect the color of the TV picture.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect power

cord from AC outlet then reconnect it after 30 minutes.

CONTRAST

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

to purple

to green

to clear

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

NOTE:

SLEEP TIMER

If the TV/DVD displays a black

box on the TV screen, this means

that the TV/DVD is set to the

TEXT mode. To clear screen, select

[CAPTION1], [CAPTION2] or

[OFF].

he Sleep Timer function enables you to shut off the power

without pressing POWER after a desired time period.

1 Set “SLEEP TIMER”

Press SLEEP on the remote control.

You may change the sleep time

with pressing SLEEP on the remote

Make sure ...

TV/DVD power must be turned on.

•

control repeatedly. The timer is set

up to 120 minutes, 30 minutes each

time SLEEP is pressed.

SLEEP 120 MINUTE

- TV SETUP -

1 Select “CAPTION”

Press SETUP on the remote control.

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press K or L to point to “CAP-

TION”.

To cancel the sleep timer:

Press SLEEP repeatedly until "SLEEP 0 MINUTE"

is displayed.

NOTES:

2 Select your desired caption menu

When you disconnect the unit from the AC outlet,

or if you have a power failure, the sleep time will

be lost.

•

- TV SETUP -

Press ENTER until your desired

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

caption menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

To view the time left for sleep timer press SLEEP

once when SLEEP display disappears. After 10

seconds, display will disappear again.

•

3 Exit the caption setting mode

Press SETUP on the remote control to return to TV

mode.

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news, etc. with either a dialogue caption or

text display.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], select [OFF] using ENTER.

Press SETUP on the remote control to return to TV

mode.

WHEN THE CLOSED CAPTION MODE

IS ON

NOTE:

The On-Screen Display will disappear after 5 sec-

onds.

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

This is also true when MUTE is pressed.

If there is a power failure of any kind, the unit will

•

retain its memory for this feature.

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts or airplane flutter.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

V-CHIP SET UP

When you select a rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “TV-Y” to [VIEW], the all ratings

will turn to [VIEW] automatically.

•

V-CHIP enables parents to prevent their children

from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels, and Emergency Broadcast

System signals), then denies access to programming

if the program’s rating meets the limitations you

select. In this case, “PROTECTED PROGRAM by

...” message appears on the TV screen.

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TV-Y7

TV-G

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

To block ratings, follow the steps below.

Programming may be rated by the Motion Picture

•

TV-MA Mature audience only

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

When you select TV-Y7, TV-PG, TV-14, or TV-MA

and you press ENTER, the sub-ratings will appear

on the TV screen.

If you select the rating category (example: TV-PG)

and turn it [BLOCK] or [VIEW], the sub-ratings

(example: V for Violence) will turn [BLOCK] or

[VIEW] automatically.

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK].

TV RATING SET UP

Make sure ...

TV/DVD power must be turned on.

•

- TV SETUP -

To set the sub-ratings individually, follow the steps

below.

1 Select “V-CHIP SET UP”

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press SETUP on the remote control.

When you select [TV-Y7]:

Press L or K to select “FV”

(Fantasy Violence).

•

Press K or L to point to “V-CHIP

SET UP”.

Then, press ENTER.

TV–Y7

[BLOCK]

Then, press ENTER to select

[BLOCK] or [VIEW].

2 Input Access code

Press Number on the remote control

to enter 4-digit access code. The

default code is 0000.

ACCESS CODE

When you select [TV-PG], [TV-14] or [TV-MA]:

Press L or K to select

•

“D”(Suggestive Dialog),

TV–PG

[BLOCK]

“L”(Coarse Language),

“S”(Sexual Situation), or

“V”(Violence). Then, press

ENTER to select [BLOCK] or [VIEW].

NOTE: When you select [TV-MA], “D” does not

appear on the TV screen.

3 Select “TV RATING”

Press K or L to point to “TV RAT-

ING”.

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

The sub-ratings which set to

Then, press ENTER.

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

[BLOCK] appears next to the rat-

ing category in the TV RATING

menu.

[BLOCK]

4 Select your desired item

Press K or L to point to your

desired item.

Then, press ENTER to select

[BLOCK] or [VIEW].

TV–Y

[VIEW]

TV–Y7

(

)

TV–G

TV–PG (

)

5 Exit the V-Chip setting mode

Press SETUP on the remote control to return to orig-

inal mode.

TV–14

(

TV–MA(

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

MPAA RATING SET UP

CHANGE ACCESS CODE

Make sure ...

To change access code, follow the steps.

TV/DVD power must be turned on.

•

1 Select “V-CHIP SET UP”

- TV SETUP -

1 Select “V-CHIP SET UP”

Press SETUP on the remote con-

- TV SETUP -

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

trol.

Press SETUP on the remote control.

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press K or L to point to “V-CHIP

SET UP”.

Press K or L to point to “V-CHIP

SET UP”.

Then, press ENTER.

ACCESS CODE

2 Enter 4-digit access code

Press Number on the remote con-

trol. The default code is 0000.

2 Enter 4-digit access code

Press Number on the remote con-

trol. The default code is 0000.

ACCESS CODE

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

3 Select “CHANGE CODE”

Press K or L to point to

“CHANGE CODE".

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

3 Select “MPAA RATING”

Press K or L to point to “MPAA

RATING”.

Then, press ENTER.

4 Enter 4-digit access code

Press Number to enter your desired

access code in the NEW CODE

space. Then, enter the same code in

the CONFIRM CODE space. V-

CHIP SET UP screen appear on the

screen.

NEW CODE

Selection

PG-13

Rating Category Explanations

General Audience

CONFIRM CODE

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

If you enter wrong code, repeat step 4, making

•

NC-17

sure you enter the same new code exactly in the

confirm code space.

Mature audience only

5 Exit the V-Chip setting mode

4 Select your desired item

Press K or L to point to your

desired item.

Then, press ENTER to select

[BLOCK] or [VIEW].

Press SETUP on the remote control to return to orig-

inal mode.

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

NOTE:

If you unplug the power code or power failure

•

When you select the rating cate-

•

occurs, the changed access code will be lost and

will return to default (0000). Change your access

code again as necessary.

gory and turn it [BLOCK], the higher rating will

turn [BLOCK] automatically. Also, the lower rat-

ing will turn [VIEW] automatically.

When you turn “G” to [VIEW], the all ratings will

turn to [VIEW] automatically.

•

5 Exit the V-Chip setting mode

Press SETUP on the remote control to return to origi-

nal mode.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS

DISC TYPES

The following discs can be played back on this TV/DVD.

[

]

DVD

Data on a DVD is divided into sections called "titles", and

then into subsections called "chapters", each of which is

given a title or chapter number. Playback conditions are

preset on some DVD video discs, and these playback con-

ditions take priority over user operations on this player. If

a function you selected does not run as desired, refer to

the manual accompanying the disc.

DVD video

DVD+R/RW*

CD-R/RW*

DVD-R/RW*

Audio CD

MP3*

* Depending on the types or the writing method of the

medium some discs can not be played.

• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs

made on personal computers, or on DVD recorders may

not be played back properly due to the factors such as

scratches, dirt or special properties of the disc.

• Discs made on personal computers may not be played

back properly due to the different environment or the

settings of the application you use. We recommend

always to use the standardized, rightly formatted discs.

(Please contact the sales agency for more detail).

Example

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

This player conforms to the NTSC color system. You can-

not play discs recorded in other color systems such as

PAL or SECAM.

[

]

AUDIO CD

Data on an audio CD is divided into sections called

“tracks”, each of which is given a track number.

¡Some discs include region codes as shown below.

Example

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

¡The number inside the symbol refers to a region of the

world, and a disc encoded in a specific region format

can only be played back on TV/DVD with the same

region code.

The following discs cannot be played back on this

TV/DVD.

[

]

MP3

Data on an MP3 is divided into sections called "groups",

and then into subsections called "tracks", each of which is

given a group or track number.

DVD with region codes other than 1 or ALL.

DVD-ROM

Example

DVD-RAM (Never play back, otherwise malfunc-

tion may result.)

Group 1

Group 2

Track 1

Track 2

Track 3

Track 4

Track 1

Track 2

CD-ROM

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-I (Never play back, otherwise malfunction

may result.)

SACD

Photo CD (Never play back, otherwise malfunc-

tion may result.)

Video CD (Never play back, otherwise malfunc-

tion may result.)

Any other discs without compatibility indications.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PLAYING A DISC

BASIC PLAYBACK

GENERAL FEATURES

DVD may contain menus to navigate the disc and

access special features. Press appropriate numerical

key or use Arrow (L/K/B/s) to highlight your selec-

tion in the DVD main menu and press ENTER to con-

firm.

DVD-V

Getting started

¡Turn on the power of amplifier and any other com-

ponents, if necessary.

NOTES

¡Select DVD mode by pressing SELECT on the

remote control. Then, press PLAY or OPEN/CLOSE

before you operate the DVD functions.

Press POWER.

¡The power will turn on.

Press OPEN/CLOSE to open disc loading

tray.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

Place the chosen disc in the tray, with the

label facing up.

DISC MENU

DVD-V

Press DISC MENU.

¡The DVD main menu will appear.

If the feature is not available,

may appear on the TV screen.

symbol

Press PLAY.

¡The tray will close automatically, and playback will

then start from the first chapter or track of the disc.

If the playback does not start automatically, press

PLAY.

If disc menu is available on the disc, audio

language, subtitle options, chapters for the

title and other options will appear for selec-

tion.

¡When you playback the DVD which a title menu is

recorded, it may appear on the screen. In this case,

refer to “TITLE MENU”.

Press Arrow (L/K/B/s) to select an item,

and ENTER to confirm selection.

Press STOP to stop playback.

TITLE MENU

NOTES

DVD-V

¡When the DVD mode has been switched to the TV

mode, the DVD mode shuts down first and then TV

picture and sound appears in about 4 seconds.

Similarly, when POWER is pressed to turn off in the

DVD mode, this mode shuts down first and then the

TV/DVD’s power is turned off.

¡A “prohibited icon” may appear at

the top-right on the TV screen dur-

ing operation, warning that a pro-

hibited operation has been encoun-

Press TITLE.

¡The title menu will appear.

If the feature is not available,

may appear on the TV screen.

symbol

Press Arrow (L/K/B/s) to select an item,

and ENTER to confirm selection.

tered by the DVD or the disc.

¡With DVDs that use titles for playback program sig-

nals, playback may start from the second title, or it

may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

CALLING UP A MENU SCREEN

DURING PLAYBACK

For DVD-Vs

¡Press DISC MENU to call up the DVD menu.

¡Press TITLE to call up the title menu.

NOTE

¡Contents of menus and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

SLOW FORWARD /

SLOW REVERSE

RESUME

DVD-V

During playback, press STOP.

¡Resume message will appear on the TV screen.

During playback, press PAUSE.

Press FWD g or REV h .

Press PLAY, playback will resume from the

point at which playback was stopped.

Press FWD g or REV h repeatedly to

select the required speed: 1/16, 1/8, 1/2 of

the normal playback.

¡To cancel resume, press STOP twice.

¡If turn off the TV/DVD, resume function will be

cancelled.

To return to normal playback, press PLAY.

Note for using buttons on the main unit:

Press PAUSE, then, press and hold down the SKIP G/

SEARCHg or SKIPH /SEARCHh on the

TV/DVD for a few seconds to begin Search in 1/16

speed of the normal playback. Press and hold down

again to change speed to 1/8. Repeat this procedure to

change to 1/2.

PAUSE

DVD-V

During playback, press PAUSE.

¡Playback will pause and sound will be muted.

To continue playback, press PLAY.

STEP BY STEP PLAYBACK

ZOOM

DVD-V

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

During playback, press PAUSE.

¡Playback will pause and sound will be muted.

Press ZOOM during playback.

¡Playback will continue.

The disc goes forward by one frame each

time PAUSE is pressed.

To exit step by step playback, press PLAY.

Press ZOOM repeatedly to select the

required zoom factor: ZOOM1, ZOOM2,

ZOOM3, or OFF.

FAST FORWARD/REVERSE

Use the Arrow (K/L/s / B) to move the

zoomed picture across the screen.

DVD-V

MP3

To exit zoom mode, press ZOOM to OFF.

NOTES

¡Zooming function does not work while disc menu is

shown.

¡Zooming function is not available on some discs.

During playback, press FWD g or REV

repeatedly to select the required forward or

reverse speed: x2, x8, x50, x100.

¡For audio CDs, the speed is fixed at ×16.

¡For MP3, the speed is fixed at ×8.

To return to normal playback, press PLAY.

Note for using buttons on the main unit:

During playback, press and hold down the SKIP G /

SEARCHg or SKIPH /SEARCHh on the

TV/DVD for a few seconds to begin Search in x2

speed. Press and hold down again to change speed to

x8. Repeat this procedure to change to x50 and x100.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

SEARCH FUNCTION

TRACK SEARCH

TIME SEARCH

DVD-V

There are three ways to begin playback on an Audio

CD at a specific Track.

During playback, press SEARCH MODE

three times (CD: twice) to display the Time

Search on the TV screen.

Using Number on the remote control

Within 30 seconds, enter a desired disc

time using Number on the remote control.

Press Number to enter the desired Track

number.

¡Playback will start at the specified time.

¡Press CLEAR to erase the incorrect input.

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, press 3).

¡To play track 26, press +10, 2, 6.

MARKER SETUP SCREEN

DVD-V

Using SEARCH MODE

Press SEARCH MODE.

¡The track search display appears.

Use markers to memorise your favorite places on a

disc.

Within 30 seconds, select a desired track

number using Number on the remote control.

Press SEARCH MODE four times (CD: three

times) during playback.

¡For single digits press 0 first.

¡Playback will start at the selected track.

¡The display screen and Markers will appear on the

TV screen.

Using SKIP

During playback, press SKIP G to move the next

track. Press it repeatedly to skip subsequent tracks.

Press SKIP H to go back to beginning of the current

track. Press it repeatedly to go to the previous tracks.

¡If SKIP is pressed while the playback is paused, the

playback will be paused again after skipping to the

next track.

Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,

7, 8, 9, or 10 and ensure that “- : - - : - -”

appears in the display.

When reaches the desired point, press

ENTER.

¡The Title or Track and elapsed playing time will

appear in the TV screen.

NOTE

¡SKIP

G are not available when playback is

stopped.

To return to the Marker later, press SEARCH

MODE four times (CD: three times) during

playback and Arrow (s /B) to choose the

desired marker, then press ENTER.

TITLE / CHAPTER SEARCH

NOTES

DVD-V

¡Opening the disc tray or turning off the power or

select AC at step 2 and press ENTER will erase all

Markers.

¡To clear a marker, using Arrow (s /B), position the

cursor on to the marker number to be cleared and

press CLEAR.

Press SEARCH MODE once for the Chapter

search, twice for the Title search during

playback.

¡You can mark up to 10 points.

Press SEARCH MODE or RETURN to exit.

Enter the desired chapter/title number using

Number on the remote control.

¡Playback will start at the selected Chapter or Track.

¡Press CLEAR to erase the incorrect input.

¡For single digits press 0 first.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

SPECIAL PLAYBACK FUNCTION

REPEAT

PROGRAM

REPEAT is available only during playback.

REPEAT TITLE / CHAPTER

You may determine the order in which tracks will play.

DVD-V

In stop mode, press MODE.

¡The PROGRAM screen will appear.

To activate the repeat function, press REPEAT

during playback.

¡The repeat mode changes as described below every

time you press the button.

Press L or M to select a track, then press

ENTER.

CHAPTER

(current chapter repeat) (current title repeat)

TITLE

OFF

(repeat off)

¡Press CLEAR to erase the

most recently entered pro-

gram.

TOTAL

NOTES

¡Repeat Title/Chapter is not available with some

scenes.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

Repeat step 2 until you have selected all the

tracks you want to play in the program.

Press PLAY to play the programmed tracks.

NOTES

REPEAT TRACK

¡While the program is being played back, the STOP

works as follows.

¡Press STOP once and then PLAY again, playback

will restart from the point where STOP was pressed.

(Program continued)

¡Press STOP twice and then PLAY again, playback will

restart from the track in the usual way. (Program cleared)

¡Up to 99 programs can be entered.

¡If you like to repeat the current track in the program,

To activate the repeat function, press REPEAT

during playback.

¡The repeat mode changes as described below every

time you press the button.

TRACK

(current track repeat)

ALL

OFF

(repeat off)

(entire disc repeat)

press REPEAT repeatedly until

TRACK appears

during playback. If you like to repeat the entire pro-

NOTES

gram press REPEAT repeatedly until

appears during playback.

ALL

¡Repeat setting will be cleared when moving to other

track.

¡Repeat playback does not function during repeat A-

B playback.

RANDOM PLAYBACK

REPEAT A-B

DVD-V CD

This shuffles the playing order of tracks instead of

playback in the sequence.

Press REPEAT A-B at your chosen starting

point.

A- appears briefly on the TV screen.

In stop mode, press MODE twice.

¡RANDOM screen appears.

RANDOM

Press REPEAT A-B again at your chosen

end point.

CD [AUDIO]

TOTAL 0:45:55

RANDOM PROGRAM

- - no indication - -

A-B appears briefly on the TV screen, and the

repeat sequence begins.

PLAY

To exit the sequence, press REPEAT A-B.

NOTES

¡The repeat A-B section can only be set within the cur- NOTE

rent title (for DVDs), or current track (for audio CDs). ¡If you like to repeat the current track in the random

Press PLAY to start random playback.

¡Repeat A-B is not available with some scenes in DVD.

¡To cancel the A point which was set, press CLEAR.

¡Repeat A-B playback does not function during title,

chapter, track or all repeat playback.

–

selection, press REPEAT repeatedly until

TRACK appears during playback. If you like to

repeat the entire random selection press REPEAT

repeatedly until

ALL appears during playback.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PLAYING A MP3 DISC

MP3 PLAYBACK

TRACK SELECTION

MP3

When a CD with MP3 files is in the TV/DVD, the

MP3 menu will appear on the TV screen in stop mode.

Press SEARCH MODE during playback.

¡The FILE LIST will appear.

In stop mode, press Arrow (K/L) to select

the desired group track.

Select a desired track using Arrow

(K/L/s/B).

¡If a group is selected, press

or ENTER to go on to the

track selection screen. Press

Arrow (K /L ) to choose a

¡Press B when you want to go to the next hierarchy.

¡Press s when you want to go back to the previous

hierarchy.

track, then press ENTER.

¡If a track is selected, press

ENTER to start playing

tracks. Starting from the one you’ve just chosen the

subsequent tracks will be played.

¡Choose FIRST PLAY to start playback from the

beginning of the listed tracks.

Press PLAY to start playback.

NOTES

¡Press SEARCH MODE to exit.

¡Some selections may take a while to be recognized.

PROGRAM

¡Press TITLE to return to the first item.

MP3

Press STOP to stop playback.

NOTES

This feature allows you to program an MP3 disc to

play in a desired sequence.

¡Folders are known as Groups; files are known as

Tracks.

¡MP3 files are accompanied by

icon.

¡Maximum of 255 folders can be recognized.

¡Maximum of 256 files can be recognized.

¡Up to 8 hierarchies can be created.

In stop mode, press MODE.

¡The PROGRAM screen will appear.

This player recommends the use of files recorded at

the below specifications:

¡Sampling frequency: 44.1kHz or 48kHz

¡Constant bit rate: 112kbps ~ 320kbps.

Select a desired track using Arrow

(K/L/s/B). Then, press ENTER.

¡Press B when you want to go to the next hierarchy.

¡Press s when you want to go back to the previous

hierarchy.

¡Press CLEAR to erase the most recently entered pro-

gram.

Repeat step 2 until you have selected all the

Tracks you want to play in the program.

Press PLAY to start programmed playback.

RANDOM PLAYBACK

MP3

In stop mode, press MODE twice.

¡RANDOM screen appears.

Press PLAY to start random playback.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CHANGING THE SETTINGS

SUBTITLE LANGUAGE

CAMERA ANGLE

DVD-V

The DVD allows you to select a language for subtitles Some DVD discs contain scenes which have been shot

during DVD disc (if available) playback. simultaneously from various angles. You can change

the camera angle when the (

screen.

) icon appears on the

Press SUBTITLE during playback.

Press SUBTITLE repeatedly to select your

desired subtitle language.

Press ANGLE during playback.

¡The selected angle will be displayed on the display

¡The subtitle language will be displayed on the dis-

play bar at the top of the screen.

bar at the top of the screen.

Press ANGLE repeatedly to select your

desired angle.

To turn off subtitles, press SUBTITLE

repeatedly until OFF appears.

NOTES

BLACK LEVEL SETTING

Some discs allow audio language setting/subtitle language

setting on the disc menu. (Operation varies between discs,

so refer to the manual accompanying the disc.)

DVD-V

¡If the desired language is not shown after pressing

SUBTITLE several times, the disc does not have

subtitles in that language.

Adjust the Black Level Settings to make the black

parts of the picture brighter.

¡If you choose a Language that has a 3 letter language

code, the code will be displayed every time you

change the Subtitle language setting. If you choose

any other languages, ‘---’ will be displayed instead.

(Refer to page 28.)

Press MODE during playback.

AUDIO LANGUAGE

Press ENTER to switch ON/OFF.

ON: Makes the dark parts brighter.

DVD-V

OFF: Shows the original picture as recorded.

The TV/DVD allows you to select a language during

DVD disc (if multi language available) playback.

Press MODE twice or RETURN to exit.

VIRTUAL SURROUND

Press AUDIO during playback.

Press AUDIO repeatedly to select your

desired language.

DVD-V

MP3

NOTE

You can enjoy stereophonic visual space on your exist-

ing stereo system.

¡Pressing AUDIO may not work on some DVDs with

multiple audio languages (e.g. DVDs which allow

audio language setting on the disc menu).

Press MODE twice (CD/MP3: once) during

playback.

STEREO SOUND MODE

OFF

Press ENTER to set it 1 (Natural effect) or 2

(Emphasized effect) or OFF.

Press AUDIO repeatedly during playback to

select between STEREO, L-CH or R-CH.

¡STEREO - both right and left channels are active

(stereo)

L-CH - only left channel is active

R-CH - only right channel is active

NOTE

Press MODE or RETURN to exit.

NOTE (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

¡If the Virtual Surround setting is ON, the sound

mode will be fixed to STEREO, and can not be

changed.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

THE ON-SCREEN INFORMATION

DVD-V

MP3

You can check the information about the current disc by pressing DISPLAY on the remote control.

For DVD-Vs

For audio CDs

Press DISPLAY during playback to show

current Chapter.

Press DISPLAY during playback to show

the current Track.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

9/49

0:00:00 -0:00:00

Press DISPLAY again to show current Total

Track.

Press DISPLAY again to show current Title.

¡The elapsed and remaining playing time of the cur-

rent total track will be displayed.

rent title will be displayed.

Press DISPLAY again.

¡The BIT RATE and the current repeat setting will be

displayed.

Press DISPLAY again to exit the display.

¡If you are playing a dual layered disc, the layer num-

ber will also be displayed (L0: Layer 0 is playing.

L1: Layer 1 is playing).

For MP3

Press DISPLAY during playback.

¡The name of the file currently in play will be dis-

Press DISPLAY again to exit the display.

played.

Press DISPLAY again to show the track

number, the repeat status, and the playback

status at the top of the screen.

will be displayed when repeat play has been

selected.

T - indicates Track repeat

G - indicates Group (folder) repeat

A - indicates Disc repeat

Press DISPLAY again to exit the display.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CHANGING THE DVD SETUP ITEMS

LANGUAGE SETTING

Language

Code Language

Code

DVD-V

A-B

L-N

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali;Bangla

Bhutani

Bihari

Bislama

Breton

4748 Laothian

4747 Latin

4752 Latvian;Lettish

6563 Lingala

4759 Lithuanian

4764 Macedonian

5471 Malagasy

4765 Malay

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

Language options are not available with some discs.

Press SETUP twice in STOP mode so that

the DVD SETUP menu appears.

¡If the menu does not appear, press PLAY, STOP,

4771 Malayalam

4772 Maltese

4847 Maori

then SETUP twice.

5167 Marathi

4860 Moldavian

5072 Mongolian

4854 Nauru

QUICK SETUP

TV MODE

DOLBY DIGITAL ON

4:3 LETTER BOX

4855 Nepali

4864 Norwegian [NOR]

4853

5971 Occitan

4851 Oriya

Oromo(Afan)

5759 Panjabi

4947 Pashto;Pushto

7254 Persian

4961 Polish

5464 Portuguese [POR]

4965 Quechua

5047 Rhaeto-Romance

6058 Romanian [RUM]

5160 Russian [RUS]

5161

5166 Samoan

Sangho

5261 Sanskrit

5256 Scots Gaelic

5255 Serbian

Bulgarian

Burmese

Byelorussian

O-R

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

Press B to select CUSTOM, then press

C-E

ENTER.

Cambodian

Catalan

¡CUSTOM mode will appear.

Chinese [CHI]

Corsican

Croatian

Press Arrow (s / B) to select LANGUAGE,

Czech

then press ENTER to confirm.

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

LANGUAGE

F-H

AUDIO

SUBTITLE

DISC MENU

ORIGINAL

OFF

ENGLISH

Faroese

Fiji

Finnish [FIN]

French [FRE]

Frisian

5264 Serbo-Croatian

5271 Sesotho

5358 Setswana

5747 Shona

Press Arrow (K/L) to select the next items,

Galician

then press ENTER.

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

AUDIO:

5051 Sindhi

5158 Singhalese

5758 Siswat

5360 Slovak

¡Sets the audio language.

SUBTITLE:

¡Sets the subtitle language.

DISC MENU:

Gujarati

Hausa

Hebrew

5367 Slovenian

5447 Somali

5569 Spanish [SPA]

5455 Sundanese

5467 Swahili

¡Sets the language for DVD menu.

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Swedish [SWE]

Press Arrow (K/L) to select a setting, then

5565

5560 Tagalog

5547 Tajik

5551 Tamil

5557 Tatar

5347 Telugu

5566 Thai

press ENTER.

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

¡If OTHER is selected on the AUDIO, SUBTITLE or

DISC MENU screen, press four-digit number to

enter the code for the desired language. (Refer to the

language code list below.)

¡Only the languages supported by the disc can be

selected.

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

5647 Tibetan

5669 Tigrinya

5760 Tonga

5765 Tsonga

5757 Turkish [TUR]

6469 Turkmen

5771 Twi

Kazakh

Kinyarwanda

Kirghiz

Kirundi

Press SETUP to exit.

NOTE

6460

U-Z

¡Language Setting for Audio and Subtitle is not avail-

able with some discs. Then use the AUDIO and the

SUBTITLE button. Details are on page 26.

Korean [KOR]

Kurdish

5761 Ukrainian

5767 Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

TO CHANGE THE ON-SCREEN MENUS

You can access the TV SETUP menu by pressing

SETUP from the DVD mode. Refer to “Selecting the

Language” on page 15 to changing the on-screen

menus.

¡In case of selecting from the DVD mode, you cannot

select “CHANNEL SET UP”, “V-CHIP SET UP”, or

“CAPTION” menus.

Yoruba

Zulu

If you choose a Language that has a 3 letter language

code, the code will be displayed every time you change

the Audio or Subtitle language setting on page 26. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

DISPLAY SETTING

AUDIO SETTINGS

Choose the appropriate Audio settings for your equip-

ment as it only affect during the playback of DVD

discs.

DVD-V

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

Press SETUP twice in STOP mode so that

the DVD SETUP menu appears.

Press SETUP twice in STOP mode so that

the DVD SETUP menu appears.

¡If the menu does not appear, press PLAY, STOP,

then SETUP twice.

QUICK SETUP

TV MODE

4:3 LETTER BOX

DOLBY DIGITAL ON

QUICK SETUP

TV MODE

4:3 LETTER BOX

DOLBY DIGITAL ON

Press B to select CUSTOM, then press

ENTER.

Press B to select CUSTOM, then press

ENTER.

¡CUSTOM mode will appear.

Press Arrow (s /B) to select AUDIO, then

press ENTER to confirm.

Press Arrow (s /B) to select DISPLAY, then

press ENTER to confirm.

AUDIO

DRC

OFF

DOLBY DIGITAL

DISPLAY

DOWN SAMPLING ON

TV MODE

4:3 LETTER BOX

ANGLE ICON

AUTO POWER OFF ON

Press Arrow (K/L) to select the below

items, then press ENTER.

DRC (Dynamic Range Control):

¡To compress the range of sound volume.

¡The default setting is OFF.

Press Arrow (K/L) to select the below

items, then press ENTER.

TV MODE:

QUICK

¡Press Arrow (K/L) for an item selection, then press

ENTER.

¡Select 4:3 LETTER BOX for a black bars appears

on top and bottom of the screen.

¡Select 4:3 PAN & SCAN for a full height picture

with both sides trimmed.

¡The default setting is 4:3 LETTER BOX.

DOLBY DIGITAL:

Set to On when the unit is connected to a Dolby Digital

Decoder.

(ON: Output by Dolby Digital)

(OFF: Convert the Dolby Digital to PCM (2 channel

stereo))

QUICK

¡The default setting is ON.

ANGLE ICON:

DOWN SAMPLING:

¡Set to ON when outputting in 48 kHz.

¡The default setting is ON.

When playing disc with copyright Protection

¡If you select OFF, copyright protection will be acti-

vated and sound will be down sampled at 48kHz.

¡Press ENTER repeatedly to turn Angle icon ON or

OFF.

¡The default setting is ON.

AUTO POWER OFF:

¡Press ENTER repeatedly to turn Auto Power off ON

or OFF.

Press SETUP to exit.

¡The default setting is ON and it will turn the

TV/DVD to off automatically after 15 minutes of no

use.

Press SETUP to exit.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

PARENTAL CONTROL

CONTROL LEVELS

DVD-V

ALL

All parental lock is cancelled.

Parental Control limits the disc viewing that exceed

your settings. (with a password or playback will stop.)

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Levels 7 to 2

PARENTAL LEVEL

Only DVD software intended for general use and

children can be played back.

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

Level 1

Press SETUP twice in STOP mode so that

the QUICK SETUP menu appears.

¡If the menu does not appear, press PLAY, STOP,

then SETUP twice.

IF YOU FORGET THE PASSWORD

QUICK SETUP

Press 4, 7, 3, 7 at step 4. Then enter your

new password.

TV MODE

4:3 LETTER BOX

DOLBY DIGITAL ON

¡Password will be cleared and parental level will be

set to ALL.

Press B to select CUSTOM, then press

ENTER.

Proceed the above Steps 5-7 again.

Press Arrow (s/B) to select PARENTAL,

then press ENTER.

PARENTAL

PARENTAL LEVEL ALL

Enter your four-digit password then press

ENTER.

Press Arrow (K/L) to select PARENTAL

LEVEL, then press ENTER.

Press Arrow (K/L) to select the desired

level.

Press SETUP to exit

NOTES

¡When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the

password from the second time onward.

¡To change the password, press Arrow (K/L) to

select CHANGE at step 5, then press ENTER. Enter

the four-digit pass-word, then press ENTER.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

¡Record the password in case you forget it.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

TROUBLESHOOTING GUIDE

If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the

player, consulting the following checklist.

Problem

Corrective Action

Make sure the power plug is connected to an AC outlet.

Make sure the power is turned on.

Check if the power plug is connected to an AC outlet.

Check the batteries in the remote control.

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote.

You have to be within 23 feet of the TV/DVD.

No power.

•

The TV/DVD does not respond to

the remote control.

•

Check if the correct mode is selected. If not switch the mode by

pressing SELECT on the remote control,whichever you need.

TV Mode

Problem

Corrective Action

No Picture or Sound

Try a new channel, if OK, then possible station trouble.

Make sure the power is turned on.

Press SELECT on the remote control to select TV mode. Then try

other TV feature.

•

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust COLOR control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

•

Bars On Screen

Picture Distorted or Blurred

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Adjust CONTRAST & BRIGHT control.

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the TV/DVD away from the appli-

ances, the TV/DVD can repair itself automatically. If you want to

repair immediately, unplug the TV/DVD power cord, then plug it in

again 30 minutes or so later.

Picture OK, Sound Poor

Different color marks on screen.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

Closed Caption Problem

My TV is showing captions

that are misspelled.

Possible Remedy

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV will not show the text

• Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to the

as being closed captioned but none • actual program so that additional advertising time can be given.

of the captions were displayed.

• Since the decoder cannot read the compressed information,

• captions will be lost.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode or CAPTION

• [OFF].

DVD Mode

Problem

Corrective Action

• Connect the video cables firmly.

No picture.

• Insert a correct video disc that plays on this TV/DVD.

• Press SELECT on the remote control to select DVD mode. Next,

press PLAY or OPEN/CLOSE. Then, try other DVD feature.

• Insert the disc.

Disc cannot be played

• Clean the disc.

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the control level.

• Connect the audio cables firmly.

No sound

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

• This TV/DVD does not support DTS audio. This is not a malfunction.

No DTS audio is output

•

There are some cases where pictures may be slightly distorted, which are not a

sign of a malfunction.

Distorted picture

• Although pictures may stop for a moment, this is not a malfunction.

Audio or subtitle language

does not match the set up

•

The selected language is not available for audio or subtitles on the DVD.

This is not a malfunction

The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera

angles. This is not a malfunction

Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected

changed

language. This is not a malfunction.

“Prohibited icon” appears on the

screen, prohibiting an operation

CD sound dropout

• That operation is prohibited by the player or the disc.

This is not a malfunction.

• Scratched disc. Replace the disc with unscratched one.

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

MAINTENANCE

CABINET CLEANING

SERVICING

Wipe the front panel and other exterior surfaces of

the TV/DVD with a soft cloth immersed in luke-

warm water and wrung dry.

Never use a solvent or alcohol. Do not spray insec-

ticide liquid near the TV/DVD. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Should your TV/DVD become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

•

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the player still does not perform properly when it is operated while referring to the relevant sections and to

"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult

your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

•

DISC HANDLING

Use discs which have the following logos on them.

(Optical audio digital discs.)

•

To clean-off, use a soft cloth.

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

•

ReWritable

Recordable

Do not use detergent or abrasive cleaning agents.

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

•

Always store the disc in its protective case when it

is not used.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

CRT :

13 or 19 inch in-line gun,

90˚ deflection tube

NTSC-M

OTHER SPECIFICATIONS

Terminals

Television system:

Antenna input:

VHF/UHF/CATV

TV Standard

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Closed caption system: §15.119/FCC

Channel coverage:

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output

(only DVD):

VHF:

UHF:

CATV:

2 ~ 13

14 ~ 69

2 ~13, A ~ W,

W+1 ~ W+84,

A-5 ~ A-1, 5A

181 channel

1/8” stereo (3.5 mm)

One pin jack,

500m Vpp (75 ohm)

Tuning System:

Channel access:

Analog audio L/R

output:

Remote control:

frequency synthesized

tuning system

Direct access keyboard,

programmable

scan and up/down

RCA connector [ 2

Digital encoded

infrared light system

Operating

temperature:

5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

[ 13 inch model ]

Power requirement : AC 120V/60Hz

Power consumption

DVD

(Maximum) :

Dimensions :

65W

Discs:

DVD video, Audio CD

H:15-13/16”(402mm)

W:14-1/2”(368mm)

D:14-13/16”(376mm)

21.6lbs (9.8kg)

Output signal format: NTSC color

Frequency response

(output jack)

DVD (linear sound): 20 Hz to 22 kHz

(sample rate: 48 kHz)

20 Hz to 44 kHz

Weight :

[ 19 inch model ]

Power requirement : AC 120V/60Hz

Power consumption

(sample rate: 96 kHz)

20 Hz to 20 kHz

CD:

(Maximum) :

Dimensions :

80W

Signal-to-noise ratio

(S/N ratio)(output jack)

CD:

Dynamic range

(output jack)

H:19-1/2”(495mm)

W:19-11/16”(500mm)

D:18-3/4”(476mm)

43.2lbs(19.6kg)

100 dB (EIAJ)

Weight :

DVD (linear sound): 85 dB

CD:

84 dB (EIAJ)

Total distortion factor

CD:

Wow and flutter:

0.07% (EIAJ)

Below the measurement

limitation (+/-0.001%

W PEAK) (EIAJ)

Designs and specifications are subject to change without notice.

If there is a discrepancy between languages, the default language will be English.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

8. Botón STOP

INDICE

Detiene la operación del disco.

9. Botón SKIP H

ꢀ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 35

PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 35

MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 35

VISTA POTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 36

ꢀ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 36

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 36

LA ANTENA INTERIOR . . . . . . . . . . . . . . . . . . . . . . . . 37

CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 37

CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 37

CONEXIÓN A UN AMPLIFICADOR EQUIPADO

Reproduce desde el inicio del capítulo o canción actual.

Botón SEARCH (REV) h (panel delantero)

Durante la reproducción o en el modo de pausa,

mantenga presionado el botón durante unos segundos

para cambiar la velocidad de reproducción hacia atrás.

10. Botón PLAY

Inicia la reproducción del contenido del disco.

Púlselo para cambiar a un modo de DVD cuando esta

en el modo de televisor.

11. Botón SKIP G

CON TOMAS DE ENTRADA DIGITAL, PLATINA

MD O PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . 37

CONEXCIONA UN DECODIFICADOR DOLBY

Reproduce desde el inicio del siguiente capítulo o

canción.

Botón SEARCH (FWD) g (panel delantero)

Durante la reproducción o en el modo de pausa,

mantenga presionado el botón durante unos segundos

para cambiar la velocidad de reproducción en avance.

DIGITAL (Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

TV SECTION

ꢀ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 38

SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 38

BORRADO (O AGREGACION) DE CANALES . . . . . . 39

12. Botón PAUSE

Hace una pausa en la operación del disco.

13. Botón OPEN/CLOSE

Púlselo para insertar discos en la bandeja o retirarlos

de ella.

DVD SECTION

ꢀ REPRODUCCIÓN DE UN DVD DE VÍDEO O UN

CD DE AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

REPRODUCCION BASICA . . . . . . . . . . . . . . . . . . . . . . 39

14.Toma HEADPHONE

Para conectar auriculares (no suministrados) y

escuchar en privado.

CONTROLES DE

OPERACIÓN Y FUNCIONES

15. Botón MODE

Activa el modo de reproducción programada o el

modo de reproducción aleatoria cuand se reproducen

CDs o MP3.

Este manual sirve para los modelos de 13" y 19". A excepción

de la apariencia, la operación de los dos modelos es exacta-

mente la misma. En este manual se muestra el modelo de 13".

16. Botones de números

Modo del televisor:

Pulse dos dígitos para tener acceso directamente al

canal deseado.

PANEL FRONTAL DEL

TELEVISOR/DVD

Recuerde pulsar "0" antes de elegir un canal de un

solo dígito.

Botón +100

Púlselo para seleccionar canales de televisión por

cable cuyo número sea igual o superior al 100.

Modo DVD:

Consulte la figura 1 de la página 8

MANDO A DISTANCIA

Púlselo para introducir el número deseado.

Botón +10

Consulte la figura 2 de la página 8

Púlselo para introducir los números deseados cuyo

número sea igual o superior al 10.

VISTA POSTERIOR

17. Botón SLEEP

Pulse el botón SLEEP para visualizar el temporizador

para dormir y activar la función. La hora de apagado

puede determinarse por el número de veces que usted

pulsa el botón. (0, 30,60,90 o 120 minutos)

Consulte la figura 3 de la página 9

1. Bandeja de carga del disco

2.Toma de entrada VIDEO

Conecte aquí la toma de salida de vídeo de una

videocámara o de una videograbadora.

18. Botón REV h

Presione para ver la imagena en DVD en retroceso

rápido. Presione PAUSE y presione este botón para

empezar la reproducción en cámara lenta. Presione

repetidamente este botón para cambiar la velocidad en

avance de la cámara lenta.

3.Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

4. Botón POWER

Botón FWD g

Púlselo para conectar y desconectar la alimentación.

Presione para avanzar rápidamente en el disco.

Presione PAUSE y presione este botón para empezar

la reproducción en cámara lenta. Presione

repetidamente este botón para cambiar la velocidad

de avance de la cámara lenta.

5. Botones VOLUME o/p(VOL.m/n)

Púlselos para controlar el nivel del volumen para el

DVD y el televisor.

6. Botones CHANNEL o/p(CH.o/p)

Púlselo para seleccionar el canal memorizado.

Púlselo para cambiar a un modo de televisor cuando

esta en el modo de DVD.

19. Botón ZOOM

Expand la Imagen para que llene toda la pantalla.

20. Botón SETUP

7. Ventanilla del sensor del mando a distancia

Púlselo para activar o salir del modo de menús de

televisor o preparación de DVD.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

38.Toma de salida AUDIO L/R

21. Botón TITLE

Conéctela a la entrada de audio analógico de un

amplificador o decodificador externo.

Visualiza el menú de títulos.

22. Botón CLEAR

39.Toma de salida de audio digital COAXIAL

(DVD Audio solamente)

Repone un ajuste.

23. Botón DISPLAY

Conéctela a la entrada digital de un amplificador o

decodificador externo.

Modo del televisor:

Púlselo para visualizar el número del canal en la

pantalla. Si lo pulsa de nuevo, el número del canal

desaparecerá.

40.Toma de entrada ANT.

Conéctela a una antena, sistema de televisión por

cable o sistema de satélite.

Modo de DVD:

Visualiza el estado actual en la pantalla del televisor

con fines de comprobación.

24. Botón SEARCH MODE

Púlselo para localizar un punto deseado.

PARA INSERTAR LAS PILAS

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a distancia en el

sentido de la flecha.

2) Inserte 2 pilas "AA" en el compartimiento de las

pilas, en el sentido indicado por las marcas de

polaridad (+/-).

25. Botón AUDIO

Púlselo para seleccionar un idioma de audio o un

modo de sonido deseado.

26. Botón SUBTITLE

Púlselo para seleccionar un idioma de subtítulos

deseado.

27. Botón REPEAT

Repite la reproducción del disco, título, capítulo o

pista actual.

3) Vuelva a poner la cubierta.

28. Botón ANGLE

NOTAS:

Púlselo para cambiar el ángulo de la cámara y ver,

desde un ángulo diferente, la secuencia que está

siendo reproducida.

No mezcle pilas alcalinas y de manganeso.

•

No mezcle pilas viejas y nuevas.

•

29. Botón A-B REPEAT

Repite la reproducción de una sección seleccionada.

30. Botón RETURN

PREPARACIÓN PARA LA

UTILIZACIÓN

Para volver a la operación anterior.

31. Botón ENTER

Púlselo para establecer un ajuste.

32. Botones de flechas

CONEXIONES DE

ANTENA/CABLE

Modo de televisor:

Púlselo para seleccionar un modo de ajuste desde el

menú que aparece en la pantalla del televisor.

Púlselo para seleccionar o ajustar desde un menú

particular.

Modo de DVD:

Se utiliza cuando se hacen ajustes mientras se

observa la visualización en una pantalla de televisor.

Consulte la figura 4 de la página 10

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención del

instalador de sistemas CATV para que tenga en

cuenta el Artículo 820-40 del NEC, el cual

proporciona consejos para hacer una conexión a

tierra apropiada y, en particular, especifica que la

tierra del cable deberá estar conectada al sistema de

puesta a tierra del edificio, tan cerca del punto de

entrada del cable como sea posible.

33. Botón DISC MENU

Visualiza menús en el DVD.

34. Botón SELECT

Púlselo para cambiar a un modo de televisor, modo

de entrada externa o modo de DVD.

NOTA: Cuando seleccione el modo DVD con

este botón, pulse primero PLAY u

NOTA:

OPEN/CLOSE. De lo contrario, las funciones del

DVD no se activarán.

Antes de enchufar la antena a la toma ANT.IN del

televisor/DVD, compruebe que la clavija no esté

doblada. Si esta doblada, póngala derecha como se

muestra en la ilustración, y luego conéctela en la

toma ANT.IN del televisor/DVD.

35. Botón MUTE

Pulse el botón MUTE para apagar el sonido de un

programa de TV. (La visualización del nivel del

sonido cambia de ROJO CLARO a AZUL CLARO.)

Pulse de nuevo el botón MUTE o el botón VOL m o

n para restaurar el sonido.

Clavija doblada

Cable

Clavija

36. Botón PICTURE

(Necesita enderezarse)

(Clavija derecha)

Presione para entrar en el modo de ajuste de imagen.

ANTENA COMBINADA DE VHF/UHF

La antena combinada de VHF/UHF de 75 ohmios

puede conectarse al terminal ANT.

37. Cable de alimentaciónConéctelo a una toma de

CA convencional (120 V/60 Hz).

NOTA: Retire el cable de alimentación del gancho

para evitar romperlo antes de conectarlo a

una toma de CA convencional.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

NOTA:

Cuando conecte una videograbadora monofónica

(otra fuente) a este televisor/DVD, conecte la toma

de salida de audio de la videograbadora

ANTENA SEPARADAS DE VHF/UHF

En algunas zonas será necesario utilizar una antena

exterior.

•

TELEVICION POR CABLE SIN CAJA

DE CONVERTIDOR / DECODIFICADOR

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su televisor/DVD sin

una caja de convertidor. Utilice el mando a distancia

del televisor/DVD para seleccionar los canales.

monofónica (otra fuente) a la toma AUDIO L de

este televisor/DVD. El audio saldrá igualmente por

los canales izquierdo y derecho.

Consulte la figura 6 de la página 11

CONEXIÓN A UN SISTEMA

ESTÉREO

TELEVICION POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATRLITE

Si su compañía de televisión por cable le suministra

una caja de convertidor, o si usted utiliza un sistema

de satélite, usted podrá utilizar la conexión básica

mostrada aquí.

Consulte la figura 7 de la página 12

NOTAS:

Asegrese de desconectar la alimentación de todos

los componentes del sistema antes de conectar otro

componente.

Consulte el manual del propietario de su sistema

estéreo y de cualquier otro componente que vaya a

conectar al televisor/DVD.

•

La selección de los canales deberá hacerse con la caja

de convertidor o con la caja de satélite. Esto significa

que los canales no se podrán cambiar utilizando el

mando a distancia del televisor/DVD.

•

PARA VER UN CANAL

Se escucha un sonido monoaural del sistema

estéreo cuando el TV/DVD está en el modo de TV.

•

CODIFICADO/DECODIFICADO

1) Ponga el selector de canales del televisor/DVD

en la posición del canal de salida de la caja de

convertidor de televisión por cable o de la caja de

satélite. (Ej., CH3)

CONEXIÓN A UN

AMPLIFICADOR EQUIPADO

CON TOMAS DE ENTRADA

DIGITAL, PLATINA MD O

PLATINA DAT (Para DVD)

2) Seleccione el canal que va a ver en su caja de

convertidor de televisión por cable o caja de

satélite.

LA ANTENA INTERIOR

Utilice un cable digital coaxial de audio de venta en

el comercio especializado para hacer las conexiones

de audio.

La antena interior (incluído para solamente 13”) es

desmontable. Inserte el vástago de la antena en el

orificio de la parte posterior superior del

televisor/DVD. Conecte la antena interior al

televisor/DVD. Para obtener la mejor recepción,

extienda completamente la antena interior y luego

haga los ajustes necesarios. (Evite tocar la sección

superior cuando haga los ajustes.)

Consulte la figura 8 de la página 12

NOTAS:

La fuente de audio de un disco en un formato de

•

sonido ambiental Dolby Digital de 5,1 canales no

se puede grabar como sonido digital mediante una

platina MD o DAT.

NOTA:

• La conexión de una antena interior puede no dar

Asegúrese de desconectar la alimentación de todos

los componentes antes de conectar otro

componente.

Consulte los manuales del propietario de los

componentes que va a conectar al televisor/DVD.

Consulte la figura 5 de la página 10

•

CONEXIÓN A TOMAS DE

ENTRADA EXTERNA

•

Ponga DOLBY DIGITAL en OFF para la salida de

•

siempre una recepción de TV aceptable.

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada de audio/vídeo de la parte delantera del

televisor/DVD.

Conecte las tomas de salida de audio/vídeo de otra

fuente a las tomas AUDIO L/R y VIDEO de este

televisor/DVD. Luego pulse SELECT hasta que

aparezca "AUX" en la pantalla.

audio en el modo de preparación. La reproducción

en un televisor/DVD utilizando ajustes incorrectos

puede causar distorsión de ruido, y también se

pueden dañar los altavoces. (Consulte la página 29

para poner DOLBY DIGITAL en OFF.)

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

CONEXCIONA UN

DECODIFICADOR DOLBY

DIGITAL (Para DVD)

TV SECTION

PREPARACIÓN PARA LA

UTILIZACIÓN

Puede programar el sintonizador para explorar todos

los canales que pueda recibir en su zona.

NOTA: La programación de la memoria de canales

no es necesaria cuando se hace la conexión a una caja

de televisión por cable o a una caja de satélite. Ponga

el selector de canales del televisor/DVD en la

posición correspondiente al canal de salida de la caja

de televisión por cable o caja de satélite (ej., CH3).

Luego seleccione el canal que va a ver en la caja de

televisión por cable o en la caja de satélite.

Si utiliza este televisor/DVD para reproducir un disco

DVD en un formato de sonido ambiental Dolby

Digital de 5,1 canales, el televisor/DVD dará salida a

un flujo de datos DOLBY DIGITAL desde su toma

de salida de audio digital COAXIAL. Conectando el

reproductor a un decodificador Dolby Digital, usted

podrá disfrutar de un ambiente más convincente y

real, con un sonido ambiental potente y de alta

calidad similar al de los cines.

Utilice cables digitales coaxiales de audio disponibles

en el comercio especializado para hacer las

conexiones de audio.

Consulte la figura 9 de la página 13

NOTAS:

SELECCIÓN DE IDIOMA

Asegúrese de desconectar la alimentación de todos

los componentes del sistema antes de conector a

otro componente.

•

1 Preparacion de canales por primera vez

Enchufe el cable de alimentación del televisor/DVD

en una toma de CA.

Consulte los manuales del propietario de los

componentes que vaya a conectar al televisor/DVD.

•

NOTA:

Si conecta un decodificador Dolby Digital, ponga

•

Si aparecen algunos dígitos en la esquina de la

pantalla, pulse POWER sin desenchufar el cable de la

alimentación.

DOLBY DIGITAL en ON para la salida de audio

en el modo de preparación. (Consulte la página 29

para poner DOLBY DIGITAL en ON.)

A menos que se haga la conexión a un

•

2 Encienda el televisor/DVD

Pulse POWER para encender el televisor/DVD.

decodificador Dolby Digital , ponga DOLBY

DIGITAL en OFF para la salida de audio en el

modo de preparación. La reproducción en el

televisor/DVD utilizando ajustes incorrectos puede

generar distorsión de ruido, y también puede

estropear los altavoces.

3 Seleccione el idioma de la pantalla

Pulse K o L para apuntar a "LANGUAGE".

Luego, pulse ENTER para seleccionar "ENGLISH" o

"ESP" = Spanish o "FRA" = French. "[ ]" indica el

idioma seleccionado.

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la D

doble son marcas de fábrica de Dolby

Laboratories.

4 Inicie el preajuste automático

Pulse K o L para apuntar a "AUTOPRESELEC-

CION". Luego, pulse ENTER. El sintonizador explo-

ra y memoriza todos los canales activos de su zona.

NOTAS:

• El televisor/DVD distingue entre los canales de TV

estándar y los canales de televisión por cable

(CATV).

• El televisor/DVD puede memorizar canales de TV

como canales de CATV si las condiciones de la

recepción no son buenas. Si pasa esto, vuelve a

intentar la acción AUTOPRESELECCION cuando

las condiciones de la recepción sean mejores.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

5 Tras la exploración

DVD SECTION

El sintonizador se detiene en el canal memorizado

más bajo. Si desea recuperar los canales

seleccionados, podrá seleccionar los canales

directamente con los botones de números o

CHANNEL(CH.) K o L.

REPRODUCCIÓN DE UN

DVD DE VÍDEO O UN CD

DE AUDIO

REPRODUCCION BASICA

BORRADO

(O AGREGACION) DE CANALES

DVD-V

Para empezar

¡Conecte el interruptor del amplificador y otros

equipos, si fuera necesario.

Los canales que ya no reciban más o que se vean

muy raramente podrán borrarse de la memoria. (Por

supuesto, podrá volver a agregar en la memoria los

canales que haya borrado de la misma.)

1 Pulse el boton POWER.

¡La alimentación se conectará.

1 Seleccione “AJUSTE DE CANAL”

Pulse SETUP en el mando a distancia. Pulse K o L

para apuntar a "AJUSTE DE CANAL".

Luego, pulse ENTER.

2 Pulse el botón OPEN/CLOSE.

¡La bandeja de carga del disco se abrirá.

2 Seleccion “AGREGAR/BORRAR”

Pulse K o L para apuntar a "AGREGAR/BORRAR".

Luego, pulse ENTER.

3 Ponga el dlsco en la bandeja con el lado

de la eliguta hacia arriba.

3 Introduzca el número del canal deseado

Pulse K o L hasta que aparezca el número del canal

deseado. (Podrá utilizar también los botones de

números o CH. K/L para introducirlos.)

(Ejemplo: CH8)

4 Pulse el botón PLAY.

¡La bandeja se cerrará automáticamente y la

reproducción empezará luego desde el primer

capítulo o pista del disco. Si la reproducción no

empieza automáticamente, pulse PLAY.

4 Bórrelo de la memoria o agréguelo a ella

Pulse ENTER. Los números de los canales se

encienden en rojo. El canal se borra de la memoria.

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú aparecerá en la pantalla.

Canal agregado: Azul claro

Canal borrado: Rojo claro

Pulse el botón STOP para detener la repro-

ducción.

¡Para borrar otro canal, repita los pasos [3] y [4].

¡Si pulsa de nuevo ENTER, el canal se memorizará

de nuevo.

5 Salga del modo de preparación de

canales

Pulse SETUP en el mando a distancia para volver al

modo del televisor.

NOTA:

Para confirmar que los canales hayan sido borrado o

agregados, pulse CHANNEL(CH.) K o L.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of

original retail purchase.

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE

RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH

THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI

AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,

please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC.

Customer Service

100 North Street; Teterboro, NJ 07608

Tel :1-800-968-3429

http://www.funai-corp.com

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

0EMN02093

_{Download from Www.Somanuals.com. All Manuals Search And Download}T_.D701/801UB #####

Sennheiser Stereo System HDI 1019 6 User Manual
Shop Vac Vacuum Cleaner 16RTP550A User Manual
Sony Battery Charger PL 383450 User Manual
Sony CD Player SCD XA1200ES User Manual
Sony Cell Phone D5503 User Manual
Sony Computer Accessories NWZ S615F User Manual
Sony Portable Multimedia Player NWZ E475BLK User Manual
Sony Recording Equipment WRT 808A User Manual
Specialized Bicycle Accessories AFR E100 User Manual
Tannoy Cell Phone W715 User Manual