LIGHTING CONTROLS
SECTION
C
Commercial Grade Lighting Controls
Lighting and Fan
Speed Controls
INDEX
Architectural Lighting Control Systems
Dimensions™ D3200 .........................................C2–C5
Architectural Specification
Van Gogh® Rotary Dimmers...................................C16
Mural Lighting Controls
Mural® L/S Preset Decora Digital Dimmers ............C19
Touch Lighting Controls
Traditional Lighting Controls
Incandescent Lighting Controls
4-Level Step Dimmer .............................................C34
Full-Range Dimmer Socket....................................C34
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS™ ARCHITECTURAL LIGHTING CONTROL SYSTEMS
Commercial Grade Lighting Controls
Dimensions D3200 Architectural Lighting Control System
The Dimensions D3200 is a component-based lighting system flexible enough for a wide range
of commercial and high-end residential lighting applications. The essential component is the
Multizone Controller/Dimmer, a self-contained programmable dimmer and scene controller that
will control up to eight zones of lighting. The unit will also function as a control unit for other
devices attached to the Leviton Control Network (LCnet). By adding wall mounted scene
controllers, a hand-held remote and a SmartJack for PC-based programming, the D3200
offers a comprehensive lighting control solution that can be expanded at any time.
Dimensions D3200 Multizone Controller/Dimmers
DESCRIPTION
CAT. NO.
LOAD RATING
COLOR
D3204 Multizone Controller/ Dimmer—Self-contained dimmer D3204-1LW
with learning IR receiver. Controls up to 4 local zones and a
maximum of 248 remote zones. Features 8 scene buttons
and 32-scene capability. LCD with wizard menus. Supplies
24VDC @ 150mA power to hardwired control devices.
120V AC 60Hz:
W
1920W/VA total output,
1000W/VA max. per zone,
1200W/VA max. per side.
For use with Incandescent, Tungsten,
Magnetic Low Voltage Transformer,
Advance Mark 10™ Powerline
Electronic Fluorescent Dimming
Ballast, Neon, Cold Cathode
and non-dimming loads.
Electronic Low Voltage and 0-10V DC
Fluorescent Hi-Lume and
Eco-10 controlled with optional
power extenders.
D3208
Dimensions D3206 Multizone Controller/Dimmer—
Self-contained dimmer with learning IR receiver. Controls
up to 6 local zones and a maximum of 186 remote zones.
Features 8 scene buttons and 32-scene capability. LCD
with wizard menus. Supplies 24VDC @ 150mA power to
hardwired control devices.
D3206-1LW
D3208-1LW
D3204-2LW
Same as D3204-1LW
W
W
W
Dimensions D3208 Multizone Controller/Dimmer—
All features of the D3206 plus: Combine/separate functionality
for 8 partitioned spaces in up to 256 configurations. Up to
64 scheduled scene changes. Easy access to 2 auxiliary
loads from front panel. Controls 62 additional remote
zones (248 max).
Same as D3204-1LW
D3204 Multizone Controller/Dimmer—same as D3204-IL
except rated for 230V loads.
230V AC 50–60Hz:
2400W/VA total output,
800W/VA max. per zone. For use with
Incandescent, Tungsten, Magnetic
Low Voltage Transformer,
Advance Mark 10™ Powerline
Electronic Fluorescent Dimming
Ballast, Neon, Cold Cathode
and non-dimming loads.
D3206 Multizone Controller/Dimmer—same as D3206-1L
except rated for 230V loads.
D3206-2LW
D32CK
Same as D3204-2LW
W
Dimensions D320x Color Change Kits
II, WW,
AA, GG,
EE, SW
2.65 (67.3)
2.26 (57.4)
*COLOR/CONTROLLERS
Available with White Frame/White Cover
(-1LW) or -2LW. For other colors, order
Cat. No. D32CK Color Change Kit and
add suffix as follows: Ivory Frame/Ivory
Cover (-II), White Frame/White Cover
(-WW), Almond Frame/Almond Cover
(-AA), Gray Frame/Gray Cover (-GG),
Black Frame/Black Cover (-EE), White
Frame/Smoke Cover (-SW).
8.80 (223.5)
D3206
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS™ ARCHITECTURAL LIGHTING CONTROL SYSTEM FEATURES
Commercial Grade Lighting Controls
Dimensions D3200 Architectural Lighting Control System
Leviton's D3204, D3206 and D3208 provide advanced, multipoint dimming and scene control for commercial
and high-end residential lighting applications within a comprehensive D3200 system or as a standalone
dimmer. The units feature menu Wizards for easy programming and lighting control, an IR receiver for use with
a handheld remote control, and a comprehensive suite of functionality including event scheduling, partitioning,
and networking. Models vary in the number of zones, availability of certain features, and voltage capacities.
Dimensions D3200 Architectural Lighting Control System
Specifications & Features
D3204 and D3206
I
Mounts in 4-gang box with 4-gang device cover
UL Listed, CSA Certified
I
I
I
41 internally-driven dimming loads (D3206); 4 for D3204
I
Controls up to 186 remote zones via Leviton Control
Network (LCnet) bus (D3206);l D3204 controls up to 248
California Title 24 compliant and meets ASHRAE Standard
90.1 requirements
I
I
6 (D3206) and 4 (D3204) Scene buttons and 32-scene
capability
Backed by a Limited Two-Year Warranty
D3208 Additional Features
I
I
2-line, 32-character LCD with Wizards for easy setup
Up to 64 scheduled scene changes based on time of day
or astronomical clock
I
LED Light-level indicators
I
Combine/Separate functionality for 8 partitions in up to
I
Group raise/lower buttons for changing all zone light levels
at same time
256 different configurations
I
Controls up to 248 remote zones
I
Learning IR Receiver
I
Easy front panel access to 2 auxiliary LCnet dimming
zones or switching loads
I
Powers LCnet controllers and Leviton SmartJack
Applications
I
I
I
I
I
I
I
I
I
Home Theaters
Great Rooms
Ballrooms
Executive Offices
Surgical Suites
Houses of Worship
Conference Rooms
Restaurants
Light Commercial
Applications
Power
Power
Extender
Extender
Auxillary
Power
Extender
Scene
Controller
Smart
Jack
LC net (2 pair Cat-5 wires)
*NOTE: first and last nodes (devices) on LCnet must be terminated.
Typical Dimensions D3200 System using a single LCNet bus
C
Download from Www.Somanuals.com. All Manuals Search And Download.
4
DIMENSIONS™ ARCHITECTURAL LIGHTING CONTROL SYSTEMS
Commercial Grade Lighting Controls
Dimensions D3200 Architectural Lighting Control System
Dimensions D3200 System Components
DESCRIPTION
Scene Controller—Decora-style 5-button wall
controller with 4 scene recall buttons
plus OFF. Features learning IR receiver.
CAT. NO.
NE505
LOAD RATING
Input Voltage: 24VDC
Input Current: 24mA
COLOR
White with
Ivory Color
option*
NE505 Color Change Kit with Customizable Labels
(wallplates sold separately)
DCK05-0C
NE515
I, W, A,
G, E
Decora Partition Controller–with 5 buttons
(4 walls and Reset). For use in D3208 system.
Input Voltage: 24VDC
Input Current: 24mA
White
with
Ivory
Color
option*
Infrared Remote Control—Handheld remote
for use with any IR-receiving D3200 Controller.
Provides 8 scene selections, group DIM/BRIGHT,
Max and OFF buttons.
NE210
No load rating—
for use with any
IR-receiving D3200
Controller
Black
Terminator Block—For use with LCnets not terminated NE600
with D3200s and with total wire length greater than 10 ft.
No load rating
White
1.75 (44.4)
1.10
(27.9)
SmartJack—Decora-style jack enables D3200 Setup
Software to be run from PC or laptop. Includes PC
cable and Software CD. Essential for any LCnet
system where PC interface is desired.†
NE100-00C
No load rating
White with
Ivory Color
option*
NE505
Power Extenders—Extend the power handling
capacity of any D3206/D3208 dimming zone or
activates auxilary zones.
See page C8
for complete
listing
Models available for
See page C8
incandescent, magnetic-
low voltage, electronic low-
voltage, Advance Mark 7™
0–10V or equivalent and
0–10VDC dimmable
0.84
(2.1)
electronic fluorescent ballasts.
See page C8 for ratings.
2.00 (50.8)
NE210
*COLOR/COMPONENTS
Cat Nos. NE505, NE515 and NE100
come in White with matching wallplate.
Include snap-on Ivory Color Change Kit.
(Ivory wallplate sold separately). With
DCK05-0C Color Change Kits add to
suffix as follows: Ivory (I), White (W),
Almond (A), Gray (G), and Black (E).
TESTING AND CODE COMPLIANCE
• UL Listed, CSA Certified, FCC Part 15
(where applicable)
• Backed by a Limited Two-Year
Warranty
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS™ ARCHITECTURAL LIGHTING CONTROL SYSTEMS
Commercial Grade Lighting Controls
Dimensions D4200 Architectural Lighting Controller
The Dimensions D4200 puts total lighting control at your fingertips. This single panel can create
and save lighting scenes, switch lights and scenes instantly or with gradual fades, and provide
complete control of up to 32 lighting zones per unit (320 per system).
Dimensions D4200 Lighting Controller
DESCRIPTION
CAT. NO.
Eight preset buttons, each with indicator pilot light. Controls virtually any type of lighting. D4200-00W
Works with up to 127 devices. Pushbutton recall of 8 scenes with 8 additional scenes
accessible from remote entry stations. Fade time can be set for each scene. Astronomical
time clock allows sequenced events based on time of day. LCD readout shows zone and
scene labels plus intensity settings. Built-in IR receiver for use with optional handheld
remotes. Electronic lock prevents unauthorized operation. Available with white frame/white
cover or white frame/black translucent cover.
White D4200 Color Change Kit (White cover and frame)
D42CK-0WW
D42CK-0SW
Smoke D4200 Color Change Kit (Smoke cover and White frame)
1.75 (44.4)
1.20
(30.6)
Dimensions D4200 Wall-Mounted Remote Stations
One-button Start/Stop Sequencer
D42P8-00W
D42SQ-00W
D42ET-00W
D42LI-NKW
D42LO-CKW
D42P1-00W
D42RL-00W
D42MO-00W
D42P1-M0W
D42MO-RLW
D42P4-00W
One-button Start/Stop Event Timer
One-button Join/Separate Link
One-button Lock/Unlock
Two-button: Preset Scene 1 and OFF, built-in IR receiver
Two-button: Master Raise and Lower, built-in IR receiver
Two-button: Preset Scene Max and OFF, built-in IR receiver
Three-button: Preset Scene 1, Max and OFF, built-in IR receiver
Four-button: Max, OFF, Master Raise and Lower, built-in IR receiver
Five-button: Preset Scenes 1–4 and OFF, built-in IR receiver
Five-button: Preset Scene 1, Max, OFF, Master Raise and Lower, built-in IR receiver D42P1-RLW
Eight-button: Preset Scenes 1–4, Max, OFF, Raise and Lower, built-in IR receiver
Eight-button: Preset Scenes 9–16
D42P4-RLW
D42P9-16W
D42P8-00W
D42P9-RLW
Ten-button: Preset Scenes 1–8, Max and OFF, built-in IR receiver
Ten-button: Preset Scenes 9–16, Raise and Lower, built-in receiver
Dimensions D4200 Room-Combine Stations
One-button: Combines 2 rooms with 1 partition
Three-button: Combines 3 rooms with 3 partitions
Four-button: Combines 4 rooms with 4 partitions
Two-button: Combines 3 rooms with 2 partitions
Three-button: Combines 4 rooms with 3 partitions
1.20
(30.6)
1.75 (44.4)
D42CS-01W
D42CS-3AW
D42CS-04W
D42CS-02W
D42CS-03W
D42CS-03W
0.84
(2.1)
Dimensions D4200 IR Handheld Controls†
Four Preset Scenes
D42IR-04L
D42IR-08L
D42IR-16L
Eight Preset Scenes
Sixteen Preset Scenes
†Remote IR Ceiling-Mount Receivers available in single-gang and 2-gang models. Consult your Leviton representative for
more information.
See page C7 For Dimensions D4200 Specifications and Features2.42 (61.2)
1.95 (49.5)
2.00 (50.8)
8.80 (223.5)
D42IR-16L
4200-00W
C
Download from Www.Somanuals.com. All Manuals Search And Download.
6
DIMENSIONS™ ARCHITECTURAL LIGHTING CONTROL SYSTEMS
Commercial Grade Lighting Controls
Dimensions D4200 Architectural Lighting Control System
Specifications & Features
I
I
I
D4200 Controller
Built-in IR Receiver
I
Controls virtually any light source when
Built-in schedule and sequence functions
used with Leviton a-2000 Dimming Panels,
MDS Dimming Cabinets, i Series e
Dimming Racks, and any DMX512
Dimming Rack (in conjunction with an
NPC XP or DLR)
Astronomical time clock allows preset or
sequence events to be called up according
to time of day
I
Mounts in 4-gang box with 4-gang
device cover
I
Controls up to 32 zones and maximum of
D4200 Remote Stations
320 zones via Luma-Net system
I
D4200
Available in 15 configurations–most have
built-in IR receiver for use with handheld
remote control
I
8 Scene buttons and 16-scene capability
I
LED light-level indicators
I
I
2-line, LCD for time, setup screens, scene
labels, zone labels, and zone intensity set-
tings from 0 to 100%
Backlighting and tactile clicking indicate
scene selection
I
Wired via Luma-Net to D4200 Controller
I
Individual raise/lower buttons for each zone
I
Mount in single-gang deep switchbox
I
I
Master raise/lower buttons for changing all
zone light levels at same time
Attractive styling accepts Decora wallplates
or Decora Plus screwless wallplates
I
D4200 Room-Combine Stations
Works with up to 127 devices (Controllers
and Remote Stations, Luma-Net Hubs and
Combine/Closure Interface)
I
Accommodates room partitions by
combining and separating lighting controls
I
Must be wired via Luma-Net to D4200
Controller
I
Minimal programming required
I
Comes with snap-on Monet-style wallplate
with silk-screened room configuration
D42P8-00W
Applications
I
I
I
I
I
I
I
I
I
Ballrooms
Hotel Suites
Restaurants
Museums
Cafeterias
Auditoriums
Lecture Halls
Conference Rooms
Houses of Worship
D4200 System Wiring Diagram, Daisy Chain Scheme
D4200 System Wiring Diagram, Hub
D4200 CONTROL STATION
D4200 CONTROL STATION
LUMA-NET III HUB
PRESET SELECT
STATION
a-2000-24
a-2000D
FULL
BRIGHT
PHASE LOSS
FULL BRIGHT
FAN
SELECT
SAVE
COMMUNICATION PORTS
AUXILIARY
DMX
CANCEL
CLEAR
LUMANET
FULL
BRIGHT
PHASE LOSS
FULL BRIGHT
FAN
SELECT
SAVE
COMMUNICATION PORT
AUXILIARY
DMX
S
CANCEL
CLEAR
LUMANET
A
B
C
PRESET SELECT
STATION
A
B
C
1
2
1
2
3
4
3
4
5
6
5
6
7
8
7
8
9
10
9
10
11
12
11
12
13
14
13
14
15
16
15
16
17
18
17
18
Note: a-2000-24 Cabinet can be in the
middle of a daisy chain
*COLOR/WALL STATIONS
For more information about the
devices on this page and Leviton's
complete line of Architectural
Lighting Control Systems, call
1-503-404-5500.
Wall stations come in white with match-
ing, screwless wallplates.
TESTING AND CODE COMPLIANCE
• Meets ASHRAE Standard 90.1
requirements
• Backed by a Limited Two-Year
Warranty
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER EXTENDERS for ARCHITECTURAL LIGHTING CONTROL SYSTEMS
Commercial Grade Lighting Controls
Standard Power Extenders
Power Extenders—PE100, PE200, PE300, PE400
DESCRIPTION
CAT. NO.
RATING
Extends dimming zone capacity to full 1920W/VA @ 120V
for incandescent, magnetic low-voltage, halogen or
neon/cold cathode lighting. Aluminum heat sink with
snap-on white cover
PE100-10W
Input Voltage: 120V 50/60Hz
Load Rating: 1920W/VA
Load Output Power: phase independent
of control device
Dimmer Input: 120V 50/60Hz
Extends dimming zone capacity to full 1920VA @ 120V
for Mark 10™ Powerline, Hi-Lume®, or equivalent
dimmable fluorescent ballast. Aluminum heat sink with
snap-on white cover
PE200-10W
PE200-70W
PE300-D0W
Input Voltage: 120V 50/60Hz
Load Rating: 1920VA
Load Output Power: phase independent
of control device
Dimmer Input: 120V 50/60Hz
Extends dimming zone capacity to full 3000VA @ 277V
for Mark 10™ Powerline, Hi-Lume®, or equivalent
dimmable fluorescent ballast. Aluminum heat sink with
snap-on white cover
Input Voltage: 277V 50/60Hz
Load Rating: 3000VA
Load Output Power: phase independent
of control device
Dimmer Input: 120V 50/60Hz
4.50 (114.3)
2.06
(52.3)
Extends dimming zone capacity to full control
of a 20A circuit with 0–10 V DC Mark 7® 0–10V,
Lutron 0–10V, OSRAM Sylvania Quicktronic® Helios™
or equivalent ballast. Metallic silver color.
Input Voltage: 120V AC to
277V AC, 60Hz
Load Rating: 20A–2400VA @ 120V AC,
5500VA @ 277V AC
PE100/200/400/AUX/AU7
Power Consumption: 6W @ 120V AC,
18W @ 277V AC
Output Ballast Control: 0–10V DC
Dimmer Input: 120V 60Hz
Extends dimming zone capacity to full control of a
1000W/VA @ 120V AC for electronic low voltage or
incandescent lighting. Aluminum heat sink with
snap-on white cover
PE400-10W
Input Voltage: 120V AC 50/60Hz
Load Rating: 1000W/VA
Load Output Power: phase independent
of control device
Dimmer Input: 120V 60Hz
Mark 10™ and Mark 7™ are trademarks of the Advance Transformer Company.
Hi-Lume® is a registered trademark of the Lutron Electronic Co., Inc.
Auxillary-Zone Network Power Extenders (for D3200 Systems only)
DESCRIPTION
CAT. NO.
RATING
Enables 2 auxiliary zones on a D3200 Controller/Dimmer
for full control over incandescent, magnetic low-voltage,
or neon/cold cathode lighting. Aluminum heat sink with
snap-on white cover
PEAUX-12W
Input Voltage: 120V AC 50/60Hz
Load Rating: 1920W/VA total,
or 1000W/VA max. per zone
Load Output Power: phase independent
of control device
3.62
(91.9)
4.00 (101.6)
Dimmer Input: D3200
PE300-DOW
Enables 1 auxiliary zone on a D3200 Controller/Dimmer
for full control over incandescent, magnetic low-voltage,
or neon/cold cathode lighting Aluminum heat sink with
snap-on white cover
PEAUX-AUW
PEAU7-M1W
Input Voltage: 230V AC 50/60Hz
Load Rating: 2400 W/VA total
Load Output Power: phase independent
of control device
SPECIFICATIONS AND FEATURES
Standard Power Extenders
• Emulates characteristics of dimmer it
is connected to in terms of dimming
range and resolution
• Low-end trim available for setting
minimum brightness level (PE100,
PE200, PE300)
Dimmer Input: D3200
Enables 1 auxiliary zone on a D3200 Controller/Dimmer
for full control over Mark 7™ 0-10V, OSRAM
Sylvania Quicktronic Helios, Lutron 0-10V, or equivalent
ballasts. Aluminum heat sink with snap-on white cover
Input Voltage: 120-230V 50-60Hz
Output Ballast Control: 0-10V DC
Load Rating: 20A-120V & 10A-230V
Load Output Power: phase independent
of control device
Dimmer Input: D3200
• PE100, PE200 and PE400 can be
surface or flush mounted using 1900
Box and 2-gang raised cover
Power Extender Compatibility
Standard Power Extenders work with any Dimensions Multizone Controller/Dimmer and all Architectural
Systems. Refer to the chart below for compatibility with Leviton Box-Mounted Dimmers.
• PE300 mounts in 4" square box
POWER EXTENDER
PE100-10W
BOX-MOUNTING DIMMER COMPATIBILITY
APPLICATIONS
Must use 120V 600W Incandescent version of Acenti, IllumaTech, Mural,
True Touch, TouchPoint, ToggleTouch, Sure Slide and Home Controls.
(or 600VA version of Acenti). For Monet, use 120V 600VA Magnetic Low-
Voltage version (requires Neutral wire). For dimmers that include a
Neutral wire, the dimmer Neutral wire must be connected.
Standard Power Extenders
• Works with any D3200 Multizone
Controller/Dimmer to extend load
capacity of any zone
• Extends load capacity of box-mounted
dimmers (see compatibility chart)
• Works with all families of Leviton
Architectural Systems
Network Power Extenders
PE200-10W
PE200-70W
Must use 120V 600VA Mark 10 version Acenti, of Monet, IllumaTech,
Mural and TouchPoint. For dimmers that include a Neutral wire, the
dimmer Neutral wire must be connected. For Hi-Lume ballasts, use
incandescent dimmers. PE200-70W is compatible with all 600VA-220V
box-mounted dimmers.
• Enables a D3200 Multizone
Controller/Dimmer to accommodate
extra loads
• Works with any D3200 Multizone
Controller/Dimmer to extend load
capacity of any zone
PE300-D0W
PE400-D0W
Must use 120V 600W Incandescent version of Acenti, llumaTech, Mural,
True Touch, TouchPoint, ToggleTouch, Sure Slide and Home Controls.
For Monet, use 120V 600VA Magnetic Low-Voltage version (requires
Neutral wire). For dimmers that include a Neutral wire, the dimmer
Neutral wire must be connected.
Must use 120V 600W Incandescent version of Acenti, llumaTech, Mural,
True Touch, TouchPoint, Trimatron and Sure Slide Home Controls.
For Monet, use 120V 600VA Magnetic Low-Voltage version (requires
Neutral wire). For dimmers that include a Neutral wire, the dimmer
Neutral wire must be connected.
TESTING AND CODE COMPLIANCE
• UL Listed (except PEAUX-AUW), CSA
Certified and NOM Certified
• Backed by a Limited Two-Year
Warranty
C
Download from Www.Somanuals.com. All Manuals Search And Download.
8
ARCHITECTURAL DIMMING CABINETS
Commercial Grade Lighting Controls
a-2000 Architectural Grade Modular Dimming Cabinets
This expanded line of a-2000 Dimming Cabinets is available in numerous configurations for use in
architectural applications. These modular cabinets deliver robust precision performance typically
found only in high-end theatrical dimming systems. This user-friendly line of modular cabinets can
be equipped with a wide variety of 15A or 20A 120V, or 277V dimming modules. Relay cabinets are
also available, as are bussing and flush kits. All a-2000 cabinets integrate seamlessly with any of
Leviton’s Lighting Controls.
a-2000 Dimming Cabinets
DESCRIPTION
CAT. NO.
RATING
12-Channel 120V Architectural-Grade Single-
Phase Modular Dimming Cabinet—also available
optional analog card, and in 3-phase versions with
without analog card
A2D1L-2A0
2400W per channel. with Individual
dimmers rated 15A or 20A. For
a-2000-24
incandescent, magnetic low voltage, or
tungsten, halogen, and cold cathode.
Compatible fluorescent dimming ballasts:
0-10VDC Advance Mark 7™, OSRAM
Sylvania Quicktronic® Helios™ and Triad®
Ballastar®; 2-wire types such as Advance
Mark 10™; and 3 wire Lutron Hi-Lume®
and Eco-10
24-Channel 120V Architectural-Grade Single-
Phase Modular Dimming Cabinet (with main lugs
only)—also available in 3-phase models, and with
optional analog card, with main breaker setup, or
with both options
A2D1L-4A0
A2D3L-857
Same as A2D1L-2A0 (above)
18-Channel 277V Architectural-Grade 3-Phase
Modular Dimming Cabinet (with 15A breakers)—
also available with 20A breakers and with or
without analog card
Same as A2D1L-2A0 (top)
a-2000-24 with Relay Cabinet
Relay Cabinet—Holds up to 12 relays for straight
rated control of fluorescent and non-fluorescent
loads. Bolts directly to a-2000 cabinet to make
a single easy-to-mount cabinet.
Consult your
Leviton
Up to 12 relays. relay Individual relays
for 20A 120V, 277V and 347V
SPECIFICATIONS AND FEATURES
• 4" Depth allows surface or recess
mounting
• Compact 301/8 inch cabinet width fits
between two stud widths
representative applications.
Built-in DMX512 input for simple
integration of theatrical control
• Relay Cabinet (14.25" width) bolts
directly to Dimmer Cabinet to form
single compact unit
• Contractor-friendly design with ample
wiring space
LCD Screen for easy,
menu-driven setup
Reliable fan-cooled design
• Stackable to provide 36 or 48
dimmer channels
• Top, bottom or side feed
• Plug-in dual dimmer modules for
rapid field replacement
• Bypass switch for each dimmer
allows full-ON operation
• Theatrical-grade dual SCR dimming
circuits outperform standard triac-
based dimmers
• Operates at 97% efficiency
• Toroidal filter with 350 µsec rise time
• UL and cUL Listed
• Backed by a Limited Two-Year
Warranty
APPLICATIONS
• Ballrooms
• Cafeterias
• Auditoriums
• Lecture Halls
• Conference Rooms
• Houses of Worship
For more information about the
devices on this page and Leviton's
complete line of Architectural
Lighting Control Systems, call
1-503-404-5500.
Contractor friendly
wireways with generous
knuckle room
Slide-in dimmer modules for tool-free service
24-Channel a-2000
Front-mounted bypass switches
for dimmer override
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
ARCHITECTURAL SPECIFICATIONS LIGHTING CONTROLS FEATURES
Commercial Grade Lighting Controls
Architectural Specification Lighting Controls
Inspired by the great painters, Leviton’s Monet®, Renoir® and Van Gogh® dimmers and fan speed
controls accent today’s most beautiful interiors. Leviton’s premiere line of architectural lighting
controls can accommodate high wattage loads and mate with screwless narrow- and wide-fin
wallplates—for the ultimate flexibility in design.
Internal surge-protective MOV
Extruded aluminum heat sink
Locator LED illuminates for
easy location in dark
Built-in radio/TV
interference filter
Copper heat
spreader
Air-gap switch
eases service
Highly reliable triac
Full range slider for
smooth, precise dimming
Monet® MNI06-1LW
Features and Benefits
I
I
Full-range dimming for both single-pole and multi-
location control
Wide range of colors available through convenient
color change kits
I
I
I
I
Accommodates high-power loads
Low profile, designer styling; mates with narrow- and
wide-fin screwless wallplates
UL and CSA Listed
Backed by a Limited Five-Year Warranty
ARCHITECTURAL SPECIFICATION DIMMING AND FAN SPEED CONTROLS
Monet® Slide Dimmer
Renoir® Slide Dimmer
Rugged, full-range preset
slide dimmer for high-
power loads. With narrow
or wide fin
Van Gogh® Rotary Dimmer
Architectural yet classic
full-range rotary dimmer for
high-power incandescent
loads. Rugged design.
60800-W shown
Low-profile architectural
controls with advanced
features. With narrow or
wide fin. Matte finish.
Custom-engraved
81000-W shown
wallplates available.
MNI06-1LW shown
C
Download from Www.Somanuals.com. All Manuals Search And Download.
10
MONET® LIGHTING CONTROLS • 600–1200 WATTS • 120–277V AC 60Hz
Commercial Grade Lighting Controls
0.24
(6.10
Monet Architectural Specification Grade Preset Controls
120V and 277V AC 60Hz
Low-profile Architectural Decora Digital Preset Slide Dimmers with LED locator light. Most
Monet dimmers provide single-pole (1 location) and 3-way (multi-location) control with
Switching Remote.
Incandescent 120V AC U R
DESCRIPTION
CAT. NO.
RATING
600W
COLOR CHANGE KIT
I, W, A, G, E, B
I, W, A, G, E, B
I, W, A, G, E, B
I, W, A, G, E
Monet Dimmer (narrow fin)
Monet Dimmer (narrow fin)
Monet Dimmer (wide fin)
MNI06-1LW
MNI10-1LW
MNI15-1LW
MNI06-10W
1000W
1500W
600W
Monet Incandescent Dimmer, Single-Pole,
Unlighted (narrow fin)
1.57
(39.9)
Monet Incandescent Dimmer, Single-Pole,
Unlighted (narrow fin)
MNI10-10W
1000W
I, W, A, G, E
2.75 (69.9)
MNI06-1LW
Low-Voltage 120V AC U R
DESCRIPTION
Monet Dimmer (narrow fin) Electronic
Monet Dimmer (narrow fin) Magnetic
Monet Dimmer (narrow fin) Magnetic
Monet Dimmer (wide fin) Magnetic
CAT. NO.
RATING
COLOR CHANGE KIT
I, W, A, G, E, B
I, W, A, G, E, B
MNE04-1LW
MNM06-1LW
MNM10-1LW
MNM15-1LW
400VA (320W)
600VA (450W)
1000VA (800W) I, W, A, G, E, B
1500VA (1200W) I, W, A, G, E, B
Mark 10™ Fluorescent Ballast 120 and 277V AC U R
For Advance Mark 10™ Powerline fluorescent dimming ballasts.
DESCRIPTION
CAT. NO.
RATING
COLOR CHANGE KIT
Monet Mark 10 Fluorescent Dimmer (narrow fin) MNX10-1LW
1000VA 120V AC I, W, A, G, E, B
1500VA 120V AC I, W, A, G, E, B
2000VA 277V AC I, W, A, G, E, B
Monet Mark 10 Fluorescent Dimmer (wide fin)
MNX15-1LW
MNX20-7LW
Monet Mark 10 277V Fluorescent Dimmer
(narrow fin)
Monet Mark 10 277V Fluorescent Dimmer
(wide fin)
MNX30-7LW
3000VA 277V AC I, W, A, G, E, B
4.25 (108.0)
MNI15-1LW
Fan Speed Controls 120V AC U R
DESCRIPTION
CAT. NO.
RATING
COLOR CHANGE KIT
0.24
(6.1)
Monet Fan Speed Control (narrow fin)
Monet Fan Speed Control (wide fin)
MNF07-1LW
MNF10-1LW
7.5A 120V AC
10A 120V AC
I, W, A, G, E, B
I, W, A, G, E, B
Monet Accessory Products
DESCRIPTION
CAT. NO.
RATING
COLOR CHANGE KIT
Monet Remote Non-Dimming Switching
Unit for 3-Way Applications
(Unlighted)
MN00R-D0W
No load rating,
use with
I, W, G, E, A
120V & 277V
Monet
dimmers only
Color Change Kits for MN00R-D0W Monet
3-Way Switching Unit
MNK0R-00
MNKIT-SL
MNKIT-1L
I, W, G, E, A
Color Change Kit for Narrow Fin Monet
Lighted Controls
I, W, A, G, E, B
I, W, A, G, E, B
I, W, A, G, E
Color Change Kit for Wide Fin Monet
Lighted Controls
2.75 (69.9)
1.57
(39.9)
Color Change Kit for Monet Unlighted Dimmers MNKIT-S0
MN00R-D0W
Monet Adapter Plate: Allows any Decora
strap-mount device to be ganged with
either small or large-size Monet controls.
In multi-gang installations, must use on ends
MN0LA-000
(large)
MN0SA-000
(small)
Metal
Heat Sink
Monet Architectural Fin Width
Narrow: 2.75" (69.9 mm)
Wide: 4.25" (108.0 mm)
Note: Mark 10™ is a trademark of the Advance Transformer Company.
NOTE: Multi-gang wallplates are available for combining narrow and wide dimmers, with or without fins removed. Refer to page C13.
CAUTION ON RETROFITS: When
retrofitting Mark 10™ Powerline dim-
ming ballasts into fixtures that origi-
nally had Instant Start ballasts, the
sockets MUST be replaced with Rapid
Start sockets to allow proper dimmer
operation and prevent damage to the
dimming ballast. Refer to the instruc-
tions provided with the ballast and the
Leviton Mark 10™ dimmer.
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to
each phase. Consult Leviton Techline if problems persist.
Digital Lighting and Fan Speed Controls are polarity sensitive devices. Always follow the wiring instructions included
with each device. They can be used in conventional 3-way and 4-way wiring circuits only when the Control is properly
connected to the load as indicated by the device’s wiring instructions.
See page C12 for Monet Specifications and Features
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
11
MONET® LIGHTING CONTROLS • 20 AMP 120 and 120/277V
Commercial Grade Lighting Controls
Monet Architectural Specification Grade Controls
Monet Switches U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
Monet Single-Pole Rocker Switch with Screw
Terminals, Lighted (narrow fin)
MNS20-1L
20A 120V AC
I, W, A, G, E
Monet 3-Way Rocker Switch with Screw
Terminals, Unlighted (narrow fin)
MNS20-D3
MNS20-D4
20A 120/277V AC I, W, A, G, E
20A 120/277V AC I, W, A, G, E
Monet 4-Way Rocker Switch with Screw
Terminals, Unlighted (narrow fin)
.40 (10.2)
MNS20-1LW
1.04 (26.4)
2.75 (69.9)
MNS20 shown
• Screwless, designer Monet wallplates with matte
finish included. Multi-gang wallplates also available
for combining narrow and wide dimmers, with or
without fins removed (see page C13)
SPECIFICATIONS AND FEATURES
• Premier Architectural Specification Grade dimmer
combines high load capability, esthetic appearance,
digital circuitry and Scene Lighting capabilities
• Provides single-pole and 3-way switching with
Monet Non-Dimming Remote Unit
• Customized wallplate engravings available—See
your Leviton representative for more information
• Built-in radio/TV interference filter
• Low-profile architectural fins, even on wide-fin
models, for a flush fit appearance
• Protected memory during temporary power failures
• Internal MOV for surge protection
• Smooth slide-dimming operation. Push slider for
ON/OFF preset
TESTING AND CODE COMPLIANCE
• Digital circuit provides Soft-ON/Fade-OFF for
eye-pleasing effect and prolonged bulb life
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Backed by a Limited Two-Year Warranty*COLOR
• Specially designed to minimize shadows with non-
reflective, easy-to-clean matte finish. Ideal for
museums, art galleries, showrooms
Cat. No. denotes White device. For other colors,
order Color Change Kits and add suffix as follows:
Ivory (-I), White (-W), Gray (-G), Black (-E), Brown
(-B) and Almond (-A). Monet Rocker Switches listed
above do not use Color Change Kits–Add suffix to
basic Cat. No. for color selection.
• Soft, green locator LED discretely positioned
on slider
• Square Law Dimming ensures linear slide control
across entire dim and bright output range
• Hidden air-gap switch; slider moves into hidden key-
way to access air-gap switch for servicing needs.
When air gap switch is open, red line appears at top
MATERIAL CHARACTERISTICS
• Small and large size adapter plates fit all Leviton
Decora straps to make them compatible with
Monet wallplates
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
C
Download from Www.Somanuals.com. All Manuals Search And Download.
12
MONET® WALLPLATE SPECIFICATIONS
Commercial Grade Lighting Controls
Monet Multi-Gang Wallplates
Monet multi-gang wallplates are available for every permissible combi-
nation of small fin and large fin dimmers. Tables 1 and 2 can be used
to determine if a specific combination of devices is possible. When
small and large fin devices are combined, all the large fin devices
must be placed to one side and all the small fin devices must be
placed to the other side. In an installation where all the fins are broken
off, do not remove the fins from the dimmers at each of the extreme
ends of the installation.
TABLE 1 — FOR INSTALLATIONS WITH NO FINS BROKEN OFF
Wallplate Cat. No.
Number of Narrow
Fin/Wide Fin Controls
Wallbox
Requirements
MNW10-00
MNW20-00
MNW30-00
MNW40-00
MNW50-00
MNW60-00
MNW01-00
MNW02-00
MNW03-00
MNW04-00
MNW11-00
MNW21-00
MNW31-00
MNW41-00
MNW51-00
MNW12-00
MNW22-00
MNW32-00
MNW13-00
MNW23-00
1 Narrow
1-Gang
3-Gang
5-Gang
6-Gang
9-Gang
10-Gang
1-Gang
4-Gang
7-Gang
9-Gang
4-Gang
5-Gang
7-Gang
8-Gang
10-Gang
6-Gang
8-Gang
9-Gang
9-Gang
10-Gang
2 Narrow
3 Narrow
4 Narrow
5 Narrow
MONET MULTI-GANG WALLPLATE CATALOG NUMBER SYSTEM
Example: MNW31-00W
6 Narrow
1 Wide
2 Wide
Add letter to indicate color:
-I (Ivory), -W (White), -A (Almond), -G (Gray)
and -E (Black)
3 Wide
4 Wide
00 = No fins removed
FB = Fins broken off
1 Narrow/1 Wide
2 Narrow/1 Wide
3 Narrow/1 Wide
4 Narrow/1 Wide
5 Narrow/1 Wide
1 Narrow/2 Wide
2 Narrow/2 Wide
3 Narrow/2 Wide
1 Narrow/3 Wide
2 Narrow/3 Wide
Number of large-fin devices
Number of small-fin devices
Monet Wallplate
Maximum Load per Monet Dimmer Multi-Gang with Fins Broken Off
Cat. No.
Single
2-Gang
More Than
2-Gang
MNE04
MNF07
MNF10
MNI06
400VA (320W)
7.5A
300VA (240W)
6A
250VA (200W)
5.3A
TABLE 2 — FOR INSTALLATIONS WITH FINS BROKEN OFF
10A
8A
7A
Wallplate Cat. No.
Number of Narrow
Fin/Wide Fin Controls
Wallbox
Requirements
600W
500W
400W
MNI10
1000W
800W
700W
MNW20-FB
MNW30-FB
MNW40-FB
MNW50-FB
MNW60-FB
MNW70-FB
MNW80-FB
MNW90-FB
MNW02-FB
MNW03-FB
MNW04-FB
MNW05-FB
MNW11-FB
MNW21-FB
MNW31-FB
MNW41-FB
MNW51-FB
MNW61-FB
MNW71-FB
MNW81-FB
MNW12-FB
MNW22-FB
MNW32-FB
MNW42-FB
MNW52-FB
MNW62-FB
MNW13-FB
MNW23-FB
MNW33-FB
MNW43-FB
MNW14-FB
MNW24-FB
2 Narrow
2-Gang
3-Gang
4-Gang
5-Gang
6-Gang
7-Gang
8-Gang
9-Gang
3-Gang
5-Gang
7-Gang
9-Gang
3-Gang
4-Gang
5-Gang
6-Gang
7-Gang
8-Gang
9-Gang
10-Gang
5-Gang
6-Gang
7-Gang
8-Gang
9-Gang
10-Gang
7-Gang
8-Gang
9-Gang
10-Gang
9-Gang
10-Gang
MNI15
1500W
1250W
1000W
3 Narrow
MNM06
MNM10
MNM15
MNX10
MNX15
MNX20-7
MNX30-7
600VA (450W)
1000VA (800W)
1500VA (1200W)
1000VA (980W)
1500VA (1470W)
2000VA (1960W)
3000VA (2940W)
500VA (375W)
800VA (640W)
1250VA (1000W)
800VA (784W)
1250VA (1225W)
1600VA (1568W)
2500VA (2450W)
400VA (300W)
700VA (560W)
1000VA (800W)
700VA (686W)
1000VA (980W)
1400VA (1372W)
2000VA (1960W)
4 Narrow
5 Narrow
6 Narrow
7 Narrow
8 Narrow
9 Narrow
2 Wide
Note: For more information on Fin Removal, refer to the instruction sheet provided
with each Monet device.
3 Wide
4 Wide
5 Wide
3.12 (79.2 mm)
1 Narrow/1 Wide
2 Narrow/1 Wide
3 Narrow/1 Wide
4 Narrow/1 Wide
5 Narrow/1 Wide
6 Narrow/1 Wide
7 Narrow/1 Wide
8 Narrow/1 Wide
1 Narrow/2 Wide
2 Narrow/2 Wide
3 Narrow/2 Wide
4 Narrow/2 Wide
5 Narrow/2 Wide
6 Narrow/2 Wide
1 Narrow/3 Wide
2 Narrow/3 Wide
3 Narrow/3 Wide
4 Narrow/3 Wide
1 Narrow/4 Wide
2 Narrow/4 Wide
1.32
6.00 (152.4 mm) (33.5 mm)
0.161
(4.1 mm)
MNW20-00
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
13
RENOIR® LIGHTING CONTROLS • 800–2000 WATTS • 120 and 277V AC 60Hz
Commercial Grade Lighting Controls
0.75
(19.1)
Renoir Architectural Specification Preset Slide Dimmers
Renoir Incandescent 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
800W
COLOR*
Renoir Single-Pole (narrow fin)
Renoir 3-Way (narrow fin)
Renoir Single-Pole (narrow fin)
80800
I, W, GY, B
I, W, GY, B
I, W, A, GY, B
I, W
80800-3
81000
800W
1000W
1000W
1000W
1000W
1500W
1500W
2000W
2000W
2000W
2000W
Renoir Single-Pole, Illuminated (narrow fin) 81000-L
Renoir 3-Way (narrow fin)
81000-3
81000-L3
81500
I, W, A, GY, B
I, W
Renoir 3-Way, Illuminated (narrow fin)
Renoir Single-Pole (wide fin)
Renoir 3-Way (wide fin)
I, W, A, GY, B
I, W, A, GY, B
I, W, A, GY, B
I, W
81500-3
82000
Renoir Single-Pole (wide fin)
Renoir Single-Pole, Illuminated (wide fin)
Renoir 3-Way (wide fin)
82000-L
82000-3
82000-L3
I, W, A, GY
I, W
Renoir 3-Way, Illuminated (wide fin)
1.05
(26.6)
2.75 (69.9)
Renoir Magnetic Low-Voltage 120V AC 60Hz Only U R
81000-W
DESCRIPTION
CAT. NO.
71111
71113
71511
71513
RATING
COLOR*
I, W, GY, B
I, W, B
I, W
Renoir Single Pole (narrow fin)
Renoir 3-Way (narrow fin)
Renoir Single Pole (wide fin)
Renoir 3-Way (wide fin)
1000VA (800W)
1000VA (800W)
1500VA (1200W)
1500VA (1200W)
I
Renoir Fluorescent Dimming Ballasts 120V and 277V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
Renoir Fluorescent Dimmer,
Single-Pole and 3-Way (wide-fin)
26666-31
1200VA (900W) 120V AC
Advance Mark 10™ Powerline
fluorescent dimming ballast
White
Renoir Fluorescent Dimmer,
Single-Pole and 3-Way (wide-fin)
26666-37
1200VA (900W) 277V AC
Advance Mark 10™ Powerline
fluorescent dimming ballast
White
Note: For complete information on installation, ganging and derating of High Wattage Dimmers, consult Leviton's Lighting
Controls Product Selection Guide or the Dimmer Instruction Sheet provided with the device.
When ganging these units, no derating is necessary except on those units which have had both sets of snap-off, fins
removed. These shall be derated as follows:
4.50 (114.3)
Maximum Load per Renoir Dimmer Multi-Gang with Fins Broken Off
82000-W
Cat. No.
Single
2-Gang
More Than
2-Gang
26666-31
26666-37
71111/3
71511/3
80800
1200VA
1100VA
1050VA
1200VA
1200VA
1200VA
Renoir Architectural Fin Width
Narrow: 2.75" (69.9 mm)
Wide: 4.50" (108.0 mm)
1000VA (800W)
1500VA (1200W)
800W
800VA (800W)
1300VA (1200W)
700W
700VA (640W)
1100VA (1040W)
600W
81000
1000W
800W
700W
CAUTION ON RETROFITS: When
retrofitting Mark 10™ Powerline
dimming ballasts into fixtures that
originally had Instant Start ballasts,
the sockets MUST be replaced with
Rapid Start sockets to allow proper
dimmer operation and prevent
damage to the dimming ballast.
Refer to the instructions provided
with the ballast and the Leviton
Mark 10™ dimmer.
81500
1500W
1300W
1000W
82000
2000W
1800W
1500W
NOTE: For fin removal and switchbox requirements for ganging Leviton Renoir dimmers, refer to page C17.
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to
each phase. Consult Leviton Techline if problems persist.
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• ON/OFF rocker switch turns lights ON at last selected
brightness level
• Smooth-action, linear slide control for easy, precise
operation
• Backed by a Limited Five-Year Warranty
• Available in single-pole (one location) and 3-way
(multi-location) versions. 3-way dimmer is used with
standard 3-way ON/OFF switch
• Decora-styling coordinates with Leviton’s extensive
line of Decora devices
*COLOR
Add suffix to catalog numbers as follows for color
selection: Ivory (-I) White (-W), Almond (A), Gray (-GY),
Brown (-B)
• Decora-style screwless snap-on wallplates present an
attractive appearance in any application
• Slim, compact housing easily fits in standard wall
boxes
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Fins are easily removed for multi-gang applications
• Large radio/TV interference filter
• Illuminated versions available
C
Download from Www.Somanuals.com. All Manuals Search And Download.
14
RENOIR® FAN SPEED CONTROLS • 7.5–15 AMP 120V AC 60HZ
Commercial Grade Lighting Controls
0.75
(19.1)
Renoir Architectural Specification Preset Slide Fan Speed Controls
Renoir Fan Speed Controls 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
80827
81127
81527
RATING
COLOR*
I, W
Renoir Single-Pole (narrow-fin)
Renoir Single-Pole (wide-fin)
Renoir Single-Pole (wide-fin)
7.5 Amps
10 Amps
15 Amps
I, W
I, W
NOTE: For fin removal and switchbox requirements for ganging Leviton Renoir fan speed controls, refer to page C17.
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to each
phase. Consult Leviton Techline if problems persist.
1.05
(26.6)
2.75 (69.9)
80827-W
Renoir Architectural Fin Width
Narrow: 2.88" (73.2 mm)
Wide: 4.69" (119.1 mm)
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File # E-31373)
• CSA Certified (File #LR-3413)
• Smooth-action, linear slide control for easy, precise
operationr
• Manual low-end trim adjustment feature on fan
speed controls allows precise adjustment of low-
end fan settings when installing device
• Decora-styling coordinates with Leviton’s extensive
line of Decora devices
• Decora-style screwless snap-on wallplate
present an attractive appearance in any
application
• Backed by a Limited Five-Year Warranty
*COLOR
Add suffix to catalog numbers as follows for color
selection: Ivory (-I) White (-W).
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Slim, compact housing easily fits in standard wall
boxes
• Fins are easily removed for multi-gang
applications
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
15
VAN GOGH® LIGHTING CONTROLS • 800–2000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
0.75
(19.1)
Van Gogh Architectural Specification Rotary Dimmers
Van Gogh Incandescent 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
800W
COLOR*
I, W
Van Gogh Single-Pole Rotary (narrow fin)
Van Gogh 3-Way Push ON/Push OFF (narrow fin)
Van Gogh Single-Pole Rotary (narrow fin)
Van Gogh 3-Way Push ON/Push OFF (narrow fin)
Van Gogh Single-Pole Rotary (wide fin)
Van Gogh Single-Pole Rotary (wide fin)
60800
60800-3
61000
800W
I, W
1000W
1000W
1500W
2000W
I, W
61000-3
61500
I, W
I, W
62000
I, W
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to
each phase. Consult Leviton Techline if problems persist.
When ganging these units, no derating is necessary except on those units which have had both sets of snap-off, fins
removed. These shall be derated as follows:
Maximum Load per Van Gogh Dimmer Multi-Gang with Fins Broken Off
Cat. No.
Single
2-Gang
More Than
2-Gang
600W
1.32
(33.5)
60800
61000
61500
62000
800W
700W
2.75 (69.9)
1000W
1500W
2000W
800W
700W
61000-W
1300W
1800W
1100W
1500W
NOTE: For fin removal and switchbox requirements for ganging Leviton Van Gogh dimmers, refer to page C17.
Color Change Kits for 60800, 61000 Dimmer Units
DESCRIPTION
CAT. NO.
60001
Brown Cover and Matching Knob w/Gold Insert
Ivory Cover and Matching Knob w/Gold Insert
White Cover and Matching Knob w/ Silver Insert
60001-I
60001-W
Color Change Kits for 61500, 62000 Dimmer Units
DESCRIPTION
Brown Cover and Matching Knob w/Gold Insert
Ivory Cover and Matching Knob w/Gold Insert
White Cover and Matching Knob w/ Silver Insert
CAT. NO.
60002
60002-I
60002-W
Van Gogh™ Architectural Rotary Fan Speed Control 120V AC 60Hz Only
4.56 (115.8)
62000-W
DESCRIPTION
CAT. NO.
RATING
COLOR*
Van Gogh Single-Pole (wide fin)
61027
10 Amps
I, W
Note: When more than one ceiling fan is controlled, make sure the blades are rotating on all fans.
Van Gogh Architectural Fin Width
Narrow: 2.75" (69.9 mm)
Wide: 4.56" (115.8 mm)
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• Classic rotary architectural-style dimmer is a popular
choice in many installations
• Available in Rotary ON/OFF (single pole only) and
Push-ON/Push-OFF (3-way).
• UL Listed (File #E-31373, 62000 File #E-66800)
• CSA Certified (File #LR-3413)
• Backed by a Limited Five-Year Warranty
• 3-way version is used with a standard 3-way
ON/OFF switch
• Snap-on cover conceals heat fins
• Color-matched dimmer control knob with gold insert
for an attractive appearance in any installation
*COLOR
Add suffix to catalog number as follows for colors:
Ivory cover with Gold insert (-I), White cover with
Silver insert (-W).
MATERIAL CHARACTERISTICS
• Snap-off fins permit easy ganging with other devices
• Slim, compact housing easily fits in standard wall box
• Large radio/TV interference filter
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
C
Download from Www.Somanuals.com. All Manuals Search And Download.
16
GANGING AND DERATING LIGHTING CONTROLS
Commercial Grade Lighting Controls
Ganging and Derating Box-Mounted Lighting Controls
Maximum Load Per Dimmer for Multi-Ganging
All Strap-Mounted Dimmers
Ganging is an installation practice where two or more lighting controls
are mounted side-by-side using the required number of connected
wallboxes. Ganging may require the removal of part of the fins on
Architectural Dimmers or part of the mounting strap on strap-mounted
devices. In Architectural Dimmers, the metallic fins help dissipate heat
from within the device. Strap mounted dimmers use the mounting
strap for the same purpose. Therefore, removing a portion of the fins or
strap for ganging purposes will require derating the dimmers to prevent
them from overheating.
Chart 1
Dimmer
Rating
Single
2-Gang
More Than
2-Gang
500W
500W
400W
500W
800W
350VA
500VA
800VA
300W
400W
700W
250VA
400VA
700VA
600W
600W
1000W
400VA
600VA*
1000VA
1000W
400VA
600VA
1000VA
Ganging and Derating Leviton Lighting Controls
When ganging Mural, True Touch, TouchPoint, ToggleTouch and
IllumaTech controls, the side sections of the mounting strap must be
removed. Use pliers to carefully bend side sections back and forth
until they break off. The side sections of the strap dissipate heat, so
removing them requires derating the dimmer’s capacity. See Chart 1.
Note that Leviton SureSlide and Trimatron lighting controls can be
ganged without removing any sections of their mounting straps.
However, SureSlide and Trimatron controls must also be derated when
they’re ganged.
*Except IPX06-7, which requires no derating
Maximum Bulb Wattage for Magnetic Low-Voltage Lighting
The capacity of a magnetic low-voltage dimmer is its VA rating. If a
wattage rating is also listed (as in this book), it is merely an estimate of
the lamp wattage that can be placed on a UL-approved magnetic low-
voltage transformer without exceeding the dimmer's VA rating. (This
is, in turn, based on an estimate of transformer efficiency.)
Chart 2
Power To
Transformer
Transformer
Efficiency
Lamp Load
1000VA
600VA
X 80%
X 75%
= 800W
= 450W
Ganging and Leviton Renoir® and Van Gogh® Architectural Lighting Controls
When fins are broken off on wide and narrow controls for ganging purposes, the number of switch boxes required can be quickly determined by
referring to the two charts below.
Ganging
Number of Narrow Controls
Switch boxes required
Number of Narrow Controls*
Switch boxes required
for ganging Leviton
architectural controls
when all inside fins
are removed:
for ganging Leviton
0
0
1
2
3
4
5
6
0
0
1
1
2
2
3
3
4
4
5
5
6
0
0
1
2
3
4
0
•
1
4
7
9
1
•
2
•
3
•
4
•
architectural controls
when no fins are removed:
6
1
3
4
5
6
7
8
3
5
7
8
3
5
6
7
8
9
10
12
14
16
18
6
7
9
11
13
16
5
7
8
9
10
12
14
16
11
13
15
17
9
10
12
11
14
7
9
10
12
14
11
13
15
11
9
11
13
11
*Narrow controls must have fins broken off to be ganged.
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
17
MURAL® LIGHTING CONTROL FEATURES
Commercial Grade Lighting Controls
Mural Lighting Controls
IThe Leviton Mural® line is a comprehensive collection of dimmers, fan speed controls, and scene-capable
dimmers and enhancement products. These rocker style devices provide full-range digital dimming in a
sleek, Decora body that will enhance any décor.
Brightness level display
Built-in radio/TV
interference filter
Air-gap switch
eases service
MDI06-1LW
Highly reliable triac
Locator LED for easy
location in dark
Features and Benefits
I
I
Easy for people of all ages and abilities to operate
Wide range of colors available through convenient color
change kits
UL and CSA Listed
I
Digital circuitry provides eye-pleasing soft-ON/fade-OFF that
extends lamp life
I
I
®
I
Compatible with Decora screwless and Decora standard
designer wallplates
Backed by a Limited Five-Year Warranty
THE COMPREHENSIVE LINE OF MURAL DIMMING, SCENE AND FAN SPEED CONTROLS
Mural L/S Preset Dimmer
Decora rocker style digital
dimmer with LED bright-
ness level indicators. With
inner rocker for setting
brightness when lights are
off. Color-change kits
available.
Mural Preset Dimmer
Decora rocker-style digital
dimmer with LED bright-
ness level indicators.
Convenient color-change
kits available.
Mural Remote Unit
Enables multi-location
dimming when used in
conjunction with Mural
Dimmer.
Mural 7-Scene Controller
Decora style controller
sends commands for up to
7 distinct scenes to individ-
ual Mural Scene-Capable
Controllers.
MS00R-10W shown
MDI06-1LW shown
MN00C-1LW shown
MLI06-1LW shown
C
Download from Www.Somanuals.com. All Manuals Search And Download.
18
MURAL® LIGHTING CONTROLS • 600–1000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
Mural L/S (Level Set) Decora-Style Preset Digital Dimmer
All Mural L/S dimmers provide single-pole (1 location) and 3-way (multi-location) control when
used with Multi-Remote unit.
Mural L/S Preset Digital Dimmer 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
Mural L/S Incandescent LED Locator and
Brightness Display
MLI06-1L
600W
I, W, A
(G, E, B with Kit)
Mural L/S Incandescent LED Locator and
Brightness Display
MLI10-1L
1000W
I, W, A
(G, E, B with Kit)
Mural L/S Magnetic Low-Voltage
LED locator and Brightness Display
MLM06-1L
MLM10-1L
MLE03-1LW
MLX06-1L
600VA (450W)
I, W, A
(G, E, B with Kit)
Mural L/S Magnetic Low-Voltage
LED locator and Brightness Display
1000VA (800W) I, W, A
(G, E, B with Kit)
Mural L/S Electronic Low-Voltage LED
Locator and Brightness Display
350VA (280W)
W
(I, A, G, E, B with Kit)
2.38 (60.5)
1.38
(35.1)
Mural L/S Advance Mark 10™ Powerline
600VA
I, W, A
(G, E, B with Kit)
Fluorescent Dimming Ballast
MLI06-1LW
LED Locator and Brightness Display
Mural L/S Quiet Fan Speed Control
LED Locator and Brightness Display
MLF01-1L
MRI06-1L
MRI10-1L
MRM10-1L
MS00R-10
1.5A
I, W, A
(G, E, B with Kit)
Mural L/S Incandescent LED Locator
(no brightness display)
600W
1000W
I, W, A
(G, E with Kit)
Mural L/S Incandescent LED Locator
(no brightness display)
I, W, A
(G, E with Kit)
Mural L/S Magnetic Low-Voltage
LED Locator (no brightness display)
1000VA (800W) I, W, A
(G, E with Kit)
Multi-Remote Unit for
Multi-Location Dimming
(no LED locator or display)
No load rating
I, W, A
(G, E, B with Kit)
Multi-Remote Unit for Electronic Low-Voltage MSE0R-10W
Multi-Location Dimming
(no LED locator or display)
No load rating
W
(I, A, G, E, B with Kit)
Color Change Kits for Mural L/S
(ML versions)
DLKDD-1L
DRK0R-00
I, W, A, G, E, B
I, W, A, G, E, B
I, W, A, G, E
Color Change Kits for Multi-Remote Units
(no LED locator or display)
2.38 (60.5)
1.38
(35.1)
Color Change Kit for Mural L/S (MR versions) MRK0D-0L
MRI06-1LW
See Page C8 for more information on Leviton Power Extenders
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to
each phase. Consult Leviton Techline if problems persist.
Digital Lighting and Fan Speed Controls are polarity sensitive devices. Always follow the wiring instructions included with
each device. They can be used in conventional 3-way and 4-way wiring circuits only when the Control is properly con-
nected to the load as indicated by the device’s wiring instructions.
CAUTION ON RETROFITS: When retrofitting Mark 10™ Powerline dimming ballasts into fixtures that originally had Instant
Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and prevent dam-
age to the dimming ballast. Refer to the instructions provided with the ballast and the Leviton Mark 10™ dimmer.
• Minimum brightness adjustment sets comfortable
SPECIFICATIONS AND FEATURES
minimum light level
• Smooth Decora rocker-action for Preset ON/OFF switch-
• Power failure recovery assures retention of lighting
ing with built-in arrow-shaped rocker for DIM/BRIGHT
levels during long-term power interruptions.
control
• Built-in radio/TV interference filter
• Arrow rocker allows user to set brightness level when
• ON/OFF AC air-gap switch completely disconnects
lights are off
power to unit for bulb changing or removal from service
• Second tap on top half of rocker for full bright. Gently
double tap bottom half of rocker for fast OFF
• Easy to operate for people of all ages and abilities
• Provides single-pole (one-location) and multi-location
full range dimming when used with Multi-Remote units
• Streamlined, popular Decora styling enhances any
interior and adds a “family look” when ganged with any
Decora device
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Backed by a Limited Five-Year warranty
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark V7™,
OSRAM Sylvania Quicktronic Helios or
equivalent ballasts.
*COLOR
• Digital circuitry provides SOFT-ON/FADE-OFF operation
for an eye-pleasing effect and prolonged lamp life
• Square green LED display alongside rocker indicates
selected brightness level on ML models
To order colors, add suffix to basic catalog number.
Colors in parentheses must be ordered as Color
Change Kits. Color suffixes are: Ivory (-I), White (-W),
Almond (-A), Gray (-G), Black (-E) and Brown (-B).
• Locator LED illuminates when lights are OFF
MATERIAL CHARACTERISTICS
• Color change kits available in a wide range of choices,
making it easy and economical to change decorating
schemes
• Color change kits simplify inventory for distributors and
contractors who can offer a complete range of colors
without stocking a different device for each one
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
19
MURAL® LIGHTING CONTROLS • 600–1000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
Mural Decora-Style Preset Digital Dimmer
All Mural dimmers provide single-pole (1 location) and 3-way (multi-location) control when
used with Multi-Remote unit.
Mural Digital Dimmer 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
Mural Incandescent LED Locator
and Brightness Display
MDI06-1L
600W
I, W, A
(G, E, B with Kit)
Mural Incandescent LED Locator
and Brightness Display
MDI10-1L
1000W
I, W, A
(G, E, B with Kit)
Mural Magnetic Low-Voltage LED Locator
and Brightness Display
MDM06-1L
MDM10-1L
MDE03-1LW
MDF01-1L
MSI06-1L
600VA (450W)
I, W, A
(G, E, B with Kit)
Mural Magnetic Low-Voltage LED Locator
and Brightness Display
1000VA (800W) I, W, A
(G, E, B with Kit)
Mural Electronic Low-Voltage LED Locator
and Brightness Display
350VA (280W)
W
2.38 (60.5)
(I, A, G, E, B with Kit)
1.32
(33.6)
Mural Quiet Fan Speed Control LED Locator
and Brightness Display
1.5A
I, W, A
(G, E, B with Kit)
MDI06-1LW
Mural Incandescent LED Locator
(no Brightness Display)
600W
I, W, A
(G, E with Kit)
Mural Incandescent LED Locator
(no Brightness Display)
MSI10-1LW
MSM10-1LW
1000W
W
(I, A, G, E with Kit)
Mural Magnetic Low-Voltage LED Locator
(no Brightness Display)
1000VA (800W)
No load rating
No load rating
W
(I, A, G, E with Kit)
Multi-Remote Unit for Multi-Location Dimming MS00R-10
(no LED locator or display)
I, W, A
(G, E with Kit)
Multi-Remote Unit for Electronic Low-Voltage MSE0R-10W
Multi-Location Dimming
(no LED locator or display)
W
(I, A, G, E with Kit)
Color Change Kits for Mural Dimmers
DESCRIPTION
CAT. NO.
COLOR*
Mural MD with LED Locator and
Brightness Display
DRKDD-1L
I, W, A, G, E, B
Mural MS with LED Locator
(no Brightness Display)
DRK0D-1L
DRK0R-00
I, W, A, G, E
I, W, A, G, E
2.38 (60.5)
1.32
(33.5)
Multi-Remote Units
(no LED Locator or Display)
MSI06-1LW
Digital Lighting and Fan Speed Controls are polarity sensitive devices. Always follow the wiring instructions included with
each device. They can be used in conventional 3-way and 4-way wiring circuits only when the Control is properly con-
nected to the load as indicated by the device’s wiring instructions.
See Page C8 for more information on Leviton Power Extenders
• Square green LED display alongside rocker indicates
SPECIFICATIONS AND FEATURES
selected brightness level on MD models
• Provides single-pole (one-location) and multi-location
• Built-in radio/TV interference filter
full range dimming when used with MS00R remote unit
• ON/OFF AC air gap switch completely disconnects
• Streamlined popular Decora styling enhances any inte-
power to unit for bulb changing or removal from service
rior and adds a family look when ganged with other
Decora devices
• Smooth ON/OFF and DIM/BRIGHT Decora rocker
action provides ease of operation for people of all ages
and abilities
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Backed by a Limited Five-Year Warranty
• Digital circuitry provides Soft-ON/Fade-OFF switching
for and eye-pleasing effect and extended lamp life
*COLOR
• Compatible with Decora screwless and Decora stan-
dard designer wallplates
• Locator LED illuminated when lights are OFF
• Color change kits available in a wide range of choices,
making it easy and economical to change decorating
schemes
• Color change kits simplify inventory for distributors and
contractors who can offer a complete range of colors
without stocking a different device for each one
To order colors, add suffix to basic catalog number.
Colors in parentheses must be ordered as Color
Change Kits. Color suffixes are: Ivory (-I), White (-W),
Almond (-A), Gray (-G), Black (-E) and Brown (-B).
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Protected memory and voltage compensation maintain
light levels after short-term power outages and during
minor power fluctuations
C
Download from Www.Somanuals.com. All Manuals Search And Download.
20
MURAL® LIGHTING CONTROLS • 600–1000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
Mural Scene Capable Decora-Style Digital Dimmer
Compatible with Scene Controller and Scene Enhancement Products — See page C22.
Mural Scene Capable Digital Dimmer 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
Mural Scene Capable Incandescent/Magnetic MCM06-1L
Low-Voltage Dimmer with LED Locator
and LED Brightness Display
600W/VA
I, W, A
(G, E, B with Kit)
Mural Scene Capable Incandescent/Magnetic MCM10-1L
Low-Voltage Dimmer with LED Locator
and LED Brightness Display
1000W/VA
I, W, A
(G, E, B with Kit)
Mural Scene Capable Mark 10™ Preset Dimmer MCX10-1LW
for 120V AC Advance Mark 10™ Powerline
Fluorescent Dimming Ballast with LED
1000VA
(750W)
W
(I, A, G, E, B with Kit)
Locator and LED Brightness Display
Color Change Kits for Mural MC
Scene Capable Dimmer
DRKDD-1L
I, W, A, G, E. B
2.38 (60.5)
1.32
(33.6)
MCM06-1LW
See Page C8 for more information on Leviton Power Extenders
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to
each phase. Consult Leviton Techline if problems persist.
Digital Lighting and Fan Speed Controls are polarity sensitive devices. Always follow the wiring instructions included with
each device. They can be used in conventional 3-way and 4-way wiring circuits only when the Control is properly con-
nected to the load as indicated by the device’s wiring instructions.
CAUTION ON RETROFITS: When retrofitting Mark 10™ Powerline dimming ballasts into fixtures that originally had Instant
Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and prevent dam-
age to the dimming ballast. Refer to the instructions provided with the ballast and the Leviton Mark 10™ dimmer.
• Color change kits simplify inventory for distributors and
SPECIFICATIONS AND FEATURES
contractors who can offer a complete range of colors
• Responds to lighting level commands sent by the Cat.
No. MN00C-1LW Scene Controller. Users can program
the desired lighting level for individual Mural Scene
Dimmers in up to seven distinct lighting scenes, which
are easily accessed by one or more Scene Controllers
• Smooth ON/OFF and Dim/Bright Decora rocker action
provides ease of operation for people of all ages and
abilities
without stocking a different device for each one
• Minimum Brightness Adjustment sets comfortable min-
imum light level
• Protected memory and voltage compensation maintain
light levels after power outages and during minor power
fluctuations
• Built-in radio/TV interference filter
• ON/OFF AC air-gap switch completely disconnects
power to unit for bulb changing or removal from service
• Scene Controller also provides an OFF button and two
arrow-shaped buttons for group Dim and Bright control
• Local Dim/Bright adjustment on individual scene dim-
mers will not affect programmed scene lighting settings
• Compatible with Scene Enhancement Products includ-
ing Contact Closure Interface, Infrared Hand-Held
Remote and Infrared Receiver, and one-way and two-
way Signal Repeater
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Backed by a Limited Five-Year warranty
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
• Streamlined, popular Decora styling enhances any inte-
rior and adds a “family look” when ganged with any
Decora device
• Digital circuitry provides SOFT-ON/FADE-OFF operation
for an eye-pleasing effect and prolonged lamp life
• Square green LED display alongside rocker indicates
selected brightness level
• Locator LED illuminates when lights are OFF
*COLOR
To order colors, add suffix to basic catalog number.
Colors in parentheses must be ordered as Color
Change Kits. Color suffixes are: Ivory (-I), White (-W),
Almond (-A), Gray (-G), Black (-E) and Brown (-B).
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Color change kits available in a wide range of choices,
making it easy and economical to change decorating
schemes
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
21
MURAL® SCENE CONTROLS • NO LOAD RATING
Commercial Grade Lighting Controls
Mural Scene Controller and Accessories
Scene Controller for Mural Scene Capable Lighting Controls U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
VScene Controller:
MN00C-1LW
No load rating,
use with 120V
Mural Scene
dimmers only
White, for
7 Lighting-Scene Buttons plus
and OFF and Group DIM
BRIGHT Buttons
other colors
use Color
Change Kits
Color Change Kits with Text for
MN00C-1LW Scene Controller
DCKS7-00
DCKS7-0C
I, W, A, G, E
Color Change Kit with Customizable Labels
for Scene Controller
No load rating
I, W, A, G, E
Scene Enhancement Products—
Compatible with Monet Scene Capable Lighting Controls U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
1.30
(33.1)
1.76 (44.7)
Signal Repeater—Must be used if
controlling lighting on more
than one circuit. One-Way and
Two-Way versions available
17100-1WY, No load rating
17100-2WY
(Non-color item)
MN00C-1LW
Contact Closure Interface—Allows control
of Mural Scene Capable devices from
home theater and building control systems
via momentary contact inputs
177BI
No load rating
(Non-color item)
Infrared Receiver—Available with
177IR-IWA
177RC
No load rating
No load rating
Supplied with
Ivory, White and
Almond bezels
Wall Mount and Ceiling Mount Bezels
Hand-Held Infrared Remote Control—
with 4 Scene Buttons plus OFF
Black
Note: A Repeater must be used on any installation that uses more than one circuit.
• Customized lettering for each scene button avail-
able (maximum of 8 characters and spaces) — see
your Leviton representative for ordering information
SPECIFICATIONS AND FEATURES
Scene Controller
• Sends commands for up to seven distinct scenes to
individual Mural Scene Capable Dimmers
• Multiple Scene Controllers can be used for multi-
point access to scenes.
• Provides OFF button and two arrow-shaped buttons
for group Dim and Bright control
• Local Dim/Bright adjustment on individual scene
dimmers will not affect programmed scene settings.
Scene Enhancement Products
• Two-Way Repeater provides scene control commu-
nication link between branch circuits. One-Way
Repeater allows the creation of separate scene con-
trol zones
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373 – Cat. Nos. MN00C and
177IR; File #E-66800 – Cat. Nos. 17100-1WY and
17100-2WY; File #E-600800 – Cat. No. 177BI )
• Green LED display for each scene button indicates
selected scene
• CSA Certified (File #LR-3413)
• Backed by a Limited Five-Year Warranty
*COLOR
• Fast, easy scene programming: Press scene button
on MN00C, adjust individual level on Mural Scene
Capable dimmer, press program button on dimmer
• Controls up to 20 scene dimmers per circuit
Basic Cat. No. denotes White device. For other
colors, order Color Change Kits and add suffix as
follows: Ivory (-I), White (-W), Gray (-G), Black (-E),
and Almond (-A).
• Streamlined, popular Decora styling enhances any
interior and adds a “family look” when ganged with
any Decora device
• Use Decora Plus or any standard Decora wallplate
MATERIAL CHARACTERISTICS
• Color change kits available in ivory, white, almond,
gray, and black allow fast color changeover and
simplify stocking inventory
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Internal MOV for surge protection
C
Download from Www.Somanuals.com. All Manuals Search And Download.
22
TOUCH LIGHTING CONTROL FEATURES
Commercial Grade Lighting Controls
Touch Lighting Controls
The Leviton Touch series includes three full-range dimming lines that use digital touch pad technology to
enable dimming and switching with a touch of a finger: True Touch™, TouchPoint™, and ToggleTouch™.
Microcontroller with onboard
non-volatile memory
Touch pad for
brightening
Locator LED for easy
location in dark
Built-in radio/TV
interference filter
Touch pad for dimming
Highly
reliable triac
Copper heat
spreader
Smooth-action
toggle arm
ToggleTouch™TGI10-1LW
Features and Benefits
I
I
I
I
Preset dimmers incorporate touchpad technology
Wide range of colors coordinates with any décor
UL and CSA Listed
Backed by a Limited Five-Year Warranty
I
Digital circuitry provides eye-pleasing soft-ON and
fade-OFF that extends lamp life (most models)
I
Single-point and multi-point control available
LEVITON TOUCH DIMMERS FOR FULL-RANGE DIMMING
True Touch™ Dimmer
Decora-style digital touch
dimmer. Provides fingertip
full-range single-pole and
multi-location dimming.
Convenient color-change
kits available.
TouchPoint™ Dimmer
Decora full-range multi-
location touch dimmer
responds to where finger
is placed on pad. With
Preset switch, LED
ToggleTouch™ Dimmer
Unique design features
toggle-style ON/OFF
switch with bright and
dim digital touch pads
alongside toggle.
locator, and LED bright-
ness indicators.
Available with LED
locator light.
TTI10-10W shown
TPI06-1LW shown
TGI10-1LW shown
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
23
TOUCHPOINT™ LIGHTING CONTROLS • 600–1000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
TouchPoint Decora-Style Preset Digital Touch-Pad Dimmer
All TouchPoint dimmers provide single-pole (1 location) and 3-way (multi-location) control when
used with Multi-Remote unit. All dimmers feature Brightness LEDs and a Locator LED.
TouchPoint Digital Touch-Pad Dimmer 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
TouchPoint Incandescent
TouchPoint Incandescent
TouchPoint Magnetic Low-Voltage
TouchPoint Magnetic Low-Voltage
TouchPoint Advance Mark 10™
Fluorescent Dimming Ballast
TPI06-1L
TPI10-1L
TPM06-1L
TPM10-1L
TPX06-1L
600W
I, W, A, G, E
I, W, A, G, E
I, W, A, G, E
1000W
600VA (450W)
1000VA (800W) I, W, A, G, E
600VA
I, W, A, G, E
TouchPoint Advance Mark 10™
Fluorescent Dimming Ballast
TPX10-1L
1000VA
I, W, A, G, E
Multi-Remote Unit for Multi-Location Dimming
(no LED locator or display)
MS00R-10W No load
White, for
1.38
(35.1)
2.38 (60.5)
rating
other colors
use Color
TPI10-1LW
Change Kits
Color Change Kits for Multi-Remote Units
(no LED locator or display)
DRK0R-00
I, W, A, G, E
See Page C8 for more information on Leviton Power Extenders
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to
each phase. Consult Leviton Techline if problems persist.
Digital Lighting and Fan Speed Controls are polarity sensitive devices. Always follow the wiring instructions included with
each device. They can be used in conventional 3-way and 4-way wiring circuits only when the Control is properly con-
nected to the load as indicated by the device’s wiring instructions.
CAUTION ON RETROFITS: When retrofitting Mark 10™ Powerline dimming ballasts into fixtures that originally had Instant
Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and prevent dam-
age to the dimming ballast. Refer to the instructions provided with the ballast and the Leviton Mark 10™ dimmer.
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• New advanced digital touch pad technology provides
full range dimming by responding to where your
finger is placed on the pad
• Provides single-pole (one-location) and multi-location
full range dimming when used with MS00R remote
unit
• Backed by a Limited Five-Year Warranty
*COLOR
Add suffix to catalog number as follows for colors:
Ivory (-I), White (-W), Gray (-G), Black (-E), and
Almond (-A).
• Attractive Decora styling blends with any interior
• Digital circuitry provides Soft-ON/Fade-OFF switching
for and eye-pleasing effect and extended lamp life
• Compatible with Decora screwless and Decora
standard designer wallplates
• Locator LED is illuminated when lights are OFF (no
LED on Remote Unit)
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Easy-to-read LED display alongside touch pad
indicates selected brightness level
• Minimum Brightness Adjustment sets comfortable
minimum light level
• Protected memory maintains light levels after power
outages and during minor power fluctuations
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
• Built-in radio/TV interference filter
C
Download from Www.Somanuals.com. All Manuals Search And Download.
24
TRUE TOUCH™ LIGHTING CONTROLS • 600–1000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
True Touch Decora-Style Digital Touch Dimmer
All True Touch dimmers provide single-pole (1 location) and 3-way (multi-location) control when
used with TrueTouch Remote.
True Touch Digital Touch Dimmer 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
True Touch Incandescent
TTI06-1AW
600W
W + A, (I, WS, GI,
GY, E, BG with kit)
True Touch Incandescent
TTI06-1EI
TTI06-1GS
TTI10-1
600W
600W
1000W
I + E, (W, A, WS,
GI, GY, BG with kit)
True Touch Incandescent
WS + GI, (W, I, A,
GY, E, BG with kit)
True Touch Incandescent
W, I, A, WS, GI,
(GY, E, BG with Kit)
True Touch Magnetic Low-Voltage
True Touch Remote Unit (no LED)
True Touch Dimmer Color Change Kit
True Touch Remote Unit Color Change Kit
TTM10-1
TT00R-1
TTKIT-0
1000VA (800W) W, I, A, WS, GI,
(GY, E, BG with Kit)
2.38 (60.5)
1.38
(35.1)
TTI10-10W
No load rating
W, I, A, WS, GI,
(GY, E, BG with Kit)
W, I, A, WS, GI,
GY, E, BG
TTKTR-0
W, I, A, WS, GI,
GY, E, BG
See Page C8 for more information on Leviton Power Extenders
Digital Lighting and Fan Speed Controls are polarity sensitive devices. Always follow the wiring instructions included with
each device. They can be used in conventional 3-way and 4-way wiring circuits only when the Control is properly con-
nected to the load as indicated by the device’s wiring instructions.
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373
• CSA Certified (File #LR-3413)
• Provides fingertip ease of use and precise adjust-
ment of lighting levels. Simple one-touch for ON at
Preset level, or again for OFF. Touch and hold for
BRIGHT/DIM lighting control
• Backed by a Limited Five-Year Warranty
• Provides single-pole (one-location) and multi-loca-
tion full range dimming when used with TT00R
remote unit
*COLOR
TTI06 comes packaged two-in-one: all White and
all Almond (AW), all Ivory and all Black (EI), and
White frame/Silver touch and Ivory frame/Gold touch
(GS). The TTI10 and TTM10 can be ordered in all
White (0W), all Ivory (0I), all Almond (0A), White
frame/Silver touch (WS), and Ivory frame/Gold touch
(GI). Color change kits include these and other
colors, add to end of catalog number as follows: all
White (0W), all Ivory (0I), all Almond (0A), White
frame/Silver touch (WS), Ivory frame/Gold touch (GI),
all Gray (GY), all Black (0E), and Brown frame/Gold
touch (BG).
• Attractive Decora styling blends with any interior
• Digital circuitry provides Soft-ON/Fade-OFF
switching for and eye-pleasing effect and extended
lamp life
• Compatible with Decora screwless and Decora
standard designer wallplates
• Locator LED is illuminated when lights are OFF (no
LED on Remote Unit)
• Color change kits offered in a wide range of colors,
making it easy and economical to change decorat-
ing schemes
• Minimum Brightness Adjustment sets comfortable
minimum light level
• Protected memory maintains light levels after
short-term power outages and during minor power
fluctuations
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Built-in radio/TV interference filter
• ON/OFF AC air gap switch completely disconnects
power to unit for bulb changing or removal from
service
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
25
TOGGLETOUCH™ LIGHTING CONTROLS • 600–1000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
ToggleTouch Toggle Digital Preset Touch Dimmer
All ToggleTouch Preset Dimmers provide single-pole (one-location) and 3-way (multi-location) control when
used with a 3-way switch, except where noted.
ToggleTouch Digital Touch Dimmer 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
ToggleTouch Incandescent
(No LED locator, single-pole only)
TGI06-10
600W
W, I, A
ToggleTouch Incandescent
TGI06-1L
TGI10-1L
TGM10-1L
600W
W, I, A,T, B
W, I, A,T, G
ToggleTouch Incandescent
1000W
ToggleTouch Magnetic Low-Voltage
1000VA (800W) W, I, A,T, G
Note: Leviton does not recommend using the ToggleTouch Dimmer with metal wallplates.
See Page C8 for more information on Leviton Power Extenders
1.75 (44.5)
1.44
(36.6)
Digital Lighting and Fan Speed Controls are polarity sensitive devices. Always follow the wiring instructions included with
each device. They can be used in conventional 3-way and 4-way wiring circuits only when the Control is properly con-
nected to the load as indicated by the device’s wiring instructions.
TGI06-1LW
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Provides a unique combination of toggle-style
ON/OFF switching and digital Touch Pad technology
• Designed for smooth ON/OFF toggle action and fin-
gertip-control touch dimming that’s easy to operate
• Backed by a Limited Five-Year Warranty
• Provides single-pole (one-location) and multi-
location 3-way control when used with a
3-way switch
*COLOR
Add suffix to catalog number as follows for other
colors: Brown (-B), Ivory (-I), White (-W), Almond (-A),
Light Almond (-T) and Gray (-G).
• Touch pads match color of toggle switch
• Fits perfectly with Leviton standard toggle
wallplates; gangs perfectly with all Leviton toggle
switches
• Provides preset dimming with soft-ON feature
(does not provide fade OFF)
MATERIAL CHARACTERISTICS
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Available with Locator LED that is illuminated when
lights are OFF
• Protected memory during temporary power failures
ensures that ToggleTouch will retain last setting
before power interruption
• Built-in radio/TV interference filter
C
Download from Www.Somanuals.com. All Manuals Search And Download.
26
TRADITIONAL LIGHTING CONTROL FEATURES
Commercial and Residential Grade Lighting Controls
Traditional Lighting Controls
Leviton offers a full line of slide, rotary and toggle dimmers and fan speed controls ideally suited to
traditional interiors. The line includes Leviton IllumaTech™, SureSlide™, and Trimatron® brand devices as
well as a number of specialty lighting devices. Leviton Traditional Controls are offered in a variety of colors.
Smooth-action slide
potentiometer
Built-in radio/TV
interference filter
Captured
slide knob
Single-pole and
3-way mechanism
Highly
reliable triac
IPI10-1LZ
Locator LED
illuminates for
easy location
in dark
Features and Benefits
I
I
I
Features slide-, rotary- and toggle-style dimmers
UL and CSA Listed
Backed by a Limited Five-Year Warranty
I
Most with full-range dimming and built-in radio/TV
interference filter
I
Single-point and multi-point control available
TRADITIONAL STYLE SLIDE AND ROTARY LIGHTING CONTROLS
IllumaTech™ Slide
SureSlide™ Slide Dimmer
Smooth-action slide control
for easy, precise operation.
Slim design ideal for multi-
gang installations. Preset
and slide-to-off versions.
6633-PLW shown
Trimatron® Rotary Dimmer
Ultra-compact, full-range
rotary dimmers.
Specialty Lighting Controls
Specialty dimmers, sockets
and switches. Emergency
switch flashes lights on and
off. Lamp-cord and 4-step
dimmers also available.
911-W shown
and Rotary Dimmers
Decora-style digital dimmer
with full-range, single- and
multi-location dimming in a
touch of a finger. Convenient
color change kits available.
IPI06-1LZ shown
6681-W shown
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
27
ILLUMATECH™ LIGHTING CONTROLS • 600–1000 WATTS • 120 and 277V AC 60Hz
Commercial Grade Lighting Controls
IllumaTech Decora-Style Preset Slide Controls
All IllumaTech Preset Dimmers provide single-pole (one-location) and 3-way (multi-location) control when
used with a 3-way switch.
IllumaTech Colors—All IllumaTech Preset Slide Controls are available in Ivory (-I), White (-W), Almond (-T),
Light Almond (-T), Gray (-G), Black (-E), Brown (-B) and Red (-R). Devices come packaged with three
colors as indicated in the chart below. Color change Kits can also be ordered separately for every color.
IllumaTech Slide Contols—Single Pole and 3-Way U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
IllumaTech Incandescent
with LED Locator
IPI06-1LZ
IPI06-1LX
600W
120V AC 60Hz
I + W + T
I + W + A
IllumaTech Incandescent
with LED Locator
IPI10-1LZ
IPI10-1LX
1000W
120V AC 60Hz
I + W + T
I + W + A
IllumaTech Electronic Low-Voltage
with LED Locator
IPE04-1LZ
IPE04-1LX
400VA (320W)
120V AC 60Hz
I + W + T
I + W + A
1.41
(35.8)
1.75 (44.5)
2.12 (53.8)
IPI10-1LZ
IllumaTech Magnetic Low-Voltage
with LED Locator
IPM06-1LZ
IPM06-1LX
600VA (450W)
120V AC 60Hz
I + W + T
I + W + A
IllumaTech Magnetic Low-Voltage
with LED Locator
IllumaTech Advance Mark 7™ 0-10V
Fluorescent Dimming Ballast
with LED Locator
IPIM10-1LZ
IPM10-1LX
1000VA (800W) I + W + T
120V AC 60Hz
1200VA @
I + W + A
I + W + T
IP710-DLZ
IP710-DLX
120V AC 60Hz, I + W + A
1500VA @
277V AC 60Hz
IllumaTech Advance Mark 10™ Powerline
Fluorescent Dimming Ballast (no LED Locator)
IPX06-1LZ
IPX06-1LX
600VA
120V AC 60Hz
I + W + T
I + W + A
IllumaTech Advance Mark 10™ Powerline
Fluorescent Dimming Ballast (no LED Locator)
IPX10-1LZ
IPX10-1LX
1000VA
120V AC 60Hz
I + W + T
I + W + A
IllumaTech Advance Mark 10™ Powerline
Fluorescent Dimming Ballast (no Locator LED)
IPX06-7LZ
IPX06-7LX
600VA
277V AC 60Hz
I + W + T
I + W + A
IllumaTech Advance Mark 10™ Powerline
Fluorescent Dimming Ballast (no Locator LED)
IPX12-7LZ
IPX12-7LX
1200VA
277V AC 60Hz
I + W + T
I + W + A
IllumaTech Quiet Fan Speed Control
with LED Locator
IPF01-1LZ
IPF01-1LX
1.5 Amps
120V AC 60Hz
I + W + T
I + W + A
IllumaTech Fan Speed Control
with LED Locator
IPF05-1LZ
IPF05-1LX
5 Amps
120V AC 60Hz
I + W + T
I + W + A
IllumaTech Color Change Kit (with LED window) IPKIT-00
I, W, A, T, G, E, B, R
I, W, A, T, G, E, B, R
I, W, A, T, G, E, B, R
with LED Locator
IllumaTech Color Change Kit (no LED window)
with LED Locator
IPKIT-0N
IPQFK-00
IllumaTech Color Change Kit for
Quiet Fan Speed Control
See Page C8 for more information on Leviton Power Extenders
Note: Sharing a neutral wire may cause flickering. Connect all dimmers to the same phase or run a separate neutral to
each phase. Consult Leviton Techline if problems persist.
CAUTION ON RETROFITS: When retrofitting Mark 10™ Powerline dimming ballasts into fixtures that originally had Instant
Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and prevent dam-
age to the dimming ballast. Refer to the instructions provided with the ballast and the Leviton Mark 10™ dimmer.
• Snap-On Color Change Kits allow color changes on
SPECIFICATIONS AND FEATURES
any device, eliminating the need to stock a separate
• Fluid slide movement allows fine adjustment of light
level with minimum effort
• Captured, wrap-around slide bar stays in place and
cannot fall off during use
device for every available color
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• Provide easy-to-use pushbutton switch with locator
LED conveniently positioned on it, making the
pushbutton easier to find in the dark
• CSA Certified (File #LR-3413)
• Backed by a Limited Five-Year Warranty
• Provide single-pole (one-location) and multi-loca-
tion lighting control when used with a 3-way switch
• Attractive Decora styling blends with any interior
• Compatible with Decora screwless and Decora
standard designer wallplates
• Power failure recovery ensures retention of last
setting before power interruption
*COLOR
IllumaTech Preset Controls come packaged with
three colors. Controls with suffix (-Z) include Ivory,
White and Light Almond; controls with suffix (-X)
include Ivory, White and Almond. Color Change Kits
are available in all colors. Add suffix to the Color
Change Kit catalog number as follows: Ivory (-I),
White (-W), Almond (-T), Light Almond (-T), Gray
(-G), Black (-E), Brown (-B) and Red (-R).
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
• Built-in radio/TV interference filter
• Quiet 1.5 Amp Fan Speed Controls are ideal for
libraries, study rooms and any area where ceiling
fan noise could become distracting. Full range
5-amp fan speed controls also available
• Color change kits feature a self-aligning mechanism
that automatically connects it to internal slider
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
C
Download from Www.Somanuals.com. All Manuals Search And Download.
28
ILLUMATECH™ LIGHTING CONTROLS • 600 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
IllumaTech Decora-Style Rotary Controls
All IllumaTech Rotary Controls combine the ease of a traditional rotary dial with the contemporary look of
Leviton Decora®.
IllumaTech Rotary Controls 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
IllumaTech Rotary Incandescent,
Single-Pole and 3-way, Illuminated
RPI06-LAW
600W
W+A
IllumaTech Rotary Incandescent,
Single-Pole and 3-way, Illuminated
RPI06-LEI
600W
I+E
IllumaTech Rotary Incandescent,
RPI06-0AW
RPI06-0EI
RTF01-0AW
RTF01-0EI
RTD01-0AW
600W
W+A
I+E
Single-Pole and 3-way, Non-Illuminated
with kit)
IllumaTech Rotary Incandescent,
Single-Pole and 3-way, Non-Illuminated
600W
IllumaTech Rotary Quiet Fan Speed Control,
Single-Pole, Non-Illuminated
1.5 Amp
1.5 Amp
W+A
I+E
1.73 (44.0)
1.30
(33.1)
IllumaTech Rotary Quiet Fan Speed Control,
Single-Pole, Non-Illuminated
RPI06-I0W
IllumaTech Rotary Dual Quiet Fan Speed Control
and Fixture Dimmer, Single-Pole, Non-Illuminated
1.5 Amp
Fan Control/
300W Dimmer
W+A
IllumaTech Rotary Dual Quiet Fan Speed Control
and Fixture Dimmer, Single-Pole, Non-Illuminated
RTD01-0EI
1.5 Amp
Fan Control/
300W Dimmer
I+E
See Page C8 for more information on Leviton Power Extenders
1.30
(33.1)
1.73 (44.0)
RTD01-10W
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Combines traditional rotary dial with contemporary
Decora styling
• Dimmers provide single-pole (one-location) or
multi-location (3-way) control when used with a
3-way switch
• Dimmers available in illuminated and non-
illuminated versions
• Quiet 1.5 Amp Fan Speed Controls are perfect for
libraries, study rooms and any area where ceiling
fan noise could become distracting
• Dual fan speed control and dimmer is ideal for
ceiling fans with built-in light fixtures
• Backed by a Limited Five-Year Warranty
*COLOR
Controls with suffix (-AW) are assembled with
Almond (-A) and White (-W) kits; controls with suffix
(-EI) are assembled with Black (-E) and Ivory (-I) kits.
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Attractive Decora styling coordinates perfectly with
Leviton’s complete line of Decora wiring devices
• Compatible with Decora Plus screwless and Decora
standard designer wallplates
• Built-in radio/TV interference filter
• Slim, compact housing fits easily into a standard
wallbox and is suitable for multi-gang installations
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
29
ILLUMATECH™ LIGHTING CONTROLS • 600–1000 WATTS • 120V AC 60Hz
Commercial Grade Lighting Controls
IllumaTech Decora-Style Slide-To-Off Controls
Single Pole Only, with LED Locator— 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR CHANGE KIT*
IllumaTech Incandescent
INI06-1L
600W
I, W, A
(T, G, E, B with Kit)
IllumaTech Incandescent (no LED locator)
IllumaTech Incandescent
INI06-10
INI10-1L
600W
I, W, A
1000W
I, W, A
(T, G, E, B with Kit)
IllumaTech Magnetic Low-Voltage
IllumaTech Magnetic Low-Voltage
IllumaTech Quiet Fan Speed Control
IllumaTech Fan Speed Control
IllumaTech Color Change Kit
INM06-1L
INM10-1L
INF01-1L
INF05-1L
600VA (450W)
I, W, A
(T, G, E, B with Kit)
1000VA (800W) I, W
(A, T, G, E, B with Kit)
1.5 Amps
I, W, A
(G, E, B with Kit)
1.26
(32.0)
1.75 (44.5)
2.12 (53.8)
5 Amps
I, W, A
(T, G, E, B with Kit)
INKIT-00
I, W, A, T, G, E, B
I, W, A, G, E, B
INI10-1LW
IllumaTech Color Change Kit
for Quiet Fan Speed Control
INQFK-00
See Page C8 for more information on Leviton Power Extenders
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Fluid slide movement allows fine adjustment of
light level with minimum effort
• Captured, wrap-around slide bar stays in place and
cannot fall off during use
• Backed by a Limited Five-Year Warranty
• Attractive Decora styling blends with any interior
*COLOR
• Compatible with Decora screwless and Decora
standard designer wallplates
• Locator LED is illuminated when lights are OFF.
LED is positioned in the same location on both
Preset and Slide-To-Off versions, giving a true
“family look” to IllumaTech
To order colors, add suffix to basic catalog number.
Colors in parentheses must be ordered as Color
Change Kits. Color suffixes are: Ivory (-I), White (-W),
Almond (-A), Light Almond (-T), Gray (-G), Black (-E)
and Brown (-B).
MATERIAL CHARACTERISTICS
• Power failure recovery ensures retention of last
setting before power interruption
• Built-in radio/TV interference filter
• Quiet 1.5 Amp Fan Speed Controls are ideal for
libraries, study rooms and any area where ceiling
fan noise could become distracting. Full range
5-amp fan speed controls also available
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
• Color change kits feature a self-aligning mecha-
nism that automatically connects it to internal
slider
• Snap-On Color Change Kits allow color changes
on any device, eliminating the need to stock a
separate device for every available color
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
C
Download from Www.Somanuals.com. All Manuals Search And Download.
30
SURESLIDE™ LIGHTING CONTROLS • 600 WATTS • 120V AC 60Hz
Residential Grade Lighting Controls
SureSlide Decora-Style Full Range Slide Controls 120V AC 60HzOnly
Incandescent U R
DESCRIPTION
CAT. NO.
RATING
600W
600W
COLOR*
SureSlide Single-Pole Slide-To-Off, Illuminated option 6631-L
I, W, A, T
SureSlide Single-Pole and 3-Way
with Preset On/OFF Switch
6623-P
I, W, GY, E, B
SureSlide Single-Pole and 3-Way
with Preset On/OFF Switch, Illuminated option
6633-PL
600W
I, W, A, T
SureSlide Dual Slide-To-Off Dimmer—(2) Single-Pole 6628
Loads, Incandescent or Magnetic Low-Voltage
300W or 300VA I, W, A, GY
per circuit;
600W/600VA Total
Low Voltage U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
1.73 (43.9)
1.34
(34.0)
SureSlide Magnetic Low-Voltage Single-Pole
with Preset ON/OFF Switch
6611-P
6613-PL
6615-P
600VA (450W)
I, W, A, GY, E, B,
6631-LW
SureSlide Magnetic Low-Voltage Single-Pole and
3-Way with Preset On/OFF Switch, Illuminated option
600VA (450W)
300W
I, W, A, T
W, T
SureSlide Electronic Low-Voltage Single-Pole and
3-Way with Preset On/OFF Switch
Advance Mark 10™ Powerline/Philips Marathon™ U R
DESCRIPTION
CAT. NO.
6668
RATING
COLOR*
SureSlide Single-Pole
Mark 10
I, W
500W-120V,
Philips Dimmable
Marathon–
350W-120V
Full-Range Fan Speed Control U R
DESCRIPTION
SureSlide Single-Pole
CAT. NO.
6627-1
6627-P
6637-P
RATING
5 Amps
5 Amps
5 Amps
COLOR*
I, W, B
SureSlide Single-Pole with Preset ON/OFF
SureSlide 3-Way with Preset ON/OFF
I, W, A, T, G, E, B
I, W, A
1.73 (43.9)
1.34
(34.0)
6633-PLW
Quiet Step Fan Speed Controls U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
(Brown Not Available)
SureSlide Single-Pole Quiet Step
6629-P
6629-3
6630
1.5 Amps
1.5 Amps
I, W, A, T, GY
I, W, A, GY
SureSlide 3-way Quiet Step with Preset ON/OFF
SureSlide Dual Quiet Fan Speed
and Fixture Dimmer
1.5A Fan/
300W Fixture
I, W, A, T, GY
See Page C8 for more information on Leviton Power Extenders
CAUTION ON RETROFITS: When retrofitting Mark 10™ Powerline dimming ballasts into fixtures that originally had Instant
Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and prevent dam-
age to the dimming ballast. Refer to the instructions provided with the ballast and the Leviton Mark 10™ dimmer.
• SureSlide Cat. No. 6668 is specially designed to work
SPECIFICATIONS AND FEATURES
with the Philips Dimmable Marathon™
• All SureSlide devices have a permanently mounted
• Preset versions provide a low-end trim adjustment for
smooth-action integrated linear slide control for easy,
precise lamp brightness and fan speed at the low-end
precise operation
settings
• SureSlide features a slim, compact housing that fits
easily into a standard wallbox and is suitable for
multi-gang installations
• Preset versions provide single-pole (one-location) and
multi-location lighting control when used with a 3-way
switch
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
• Backed by a Limited Five-Year Warranty
Use Leviton Power Extenders to extend
the load capacity of box-mounted dim-
mers. Leviton Power Extenders are
available for incandescent, magnetic
low-voltage, electronic low-voltage,
Advance Mark 10™ Powerline fluores-
cent dimming ballasts or equivalents,
and 0–10 VDC dimmable fluorescent
ballasts such as Advance Mark 7™
0–10V, OSRAM Sylvania Quicktronic
Helios or equivalent ballasts.
• Illuminated versions feature optional-use Locator LED.
*COLOR
• SureSlide’s attractive Decora styling coordinates
perfectly with Leviton’s complete line of Decora
wiring devices
• Compatible with Decora screwless and Decora
standard designer wallplates
Basic Cat. No. denotes Brown where Brown is
available. Add suffix to catalog number as follows for
other colors: Ivory (-I), White (-W), Gray (-GY), Black
(-E), Almond (-A), and Lighht Almond (-T).
• Built-in radio/TV interference filter
MATERIAL CHARACTERISTICS
• Quiet 1.5 Amp Fan Speed Controls are ideal for
libraries, study rooms and any area where ceiling fan
noise could become distracting. Full range 5-amp fan
speed controls also available
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
31
TRIMATRON™ LIGHTING CONTROLS • 600 WATTS • 120V AC 60Hz
Residential Grade Lighting Controls
Trimatron™ Deluxe Full Range Rotary Dimmers and Fan Speed Controls
Trimatron Incandescent Rotary Dimmers 600 Watts 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
600W
600W
600W
COLOR*
I, W, A
I, W, A
I, W
Trimatron Deluxe Push-ON/Push-OFF Single-Pole
Trimatron Deluxe Push-ON/Push-OFF 3-Way
Trimatron Single-Pole Deluxe Rotary
6681
6683
6602
Trimatron Single-Pole Deluxe Rotary#
(Not UL Listed or CSA Certified)
6602-220
600W-220V
50Hz AC
W
Decora Plastic Adapter for Rotary Dimmers —
Plastic, Standard size; fits over .406" dimmer shaft
80400
26115
I, W, A, E, B
Dimmer Knobs with metal insert
(packed 25 per box)
I, W, A, T, E, B
Note: All dimmers have a ground wire.
All devices are UL Listed and CSA Certified except where indicated by#
1.59 (40.4)
0.92
(23.4)
6602-W
Trimatron Fan Speed Controls 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
6616-X
6639
RATING
COLOR*
I, W
Trimatron Full-Range Fan Speed Control
Trimatron Quiet Fan Speed Control
See Page C8 for more information on Leviton Power Extenders
5 Amps
1.5 Amps
I, W
Use Leviton Power Extenders to extend the load capacity of box-mounted dimmers. Leviton Power Extenders are available
for incandescent, magnetic low-voltage, electronic low-voltage, Advance Mark 10™ Powerline fluorescent dimming
ballasts or equivalents, and 0–10 VDC dimmable fluorescent ballasts such as Advance Mark 7™ 0–10V, OSRAM Sylvania
Quicktronic Helios or equivalent ballasts.
1.30
(33.1)
1.73 (44.0)
6681-W
1.73 (44.0)
1.38
(35.1)
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
6616-XW
• Leviton Trimatron lighting controls are traditional
rotary-style dimmers featuring an ultra-compact
design that fits in even the tightest single-gang
wallboxes and is suitable for multi-gang
nstallations
• Backed by a Limited Five-Year Warranty
*COLOR
• Built-in radio/TV interference filter
Add suffix to catalog numbers as follows to select
colors: Ivory (-I), White (-W), Almond (-A), Light
Almond (-T) and Black (-E). Cat. Nos. 80400 and
26115 also available in Brown (no suffix).
• Quiet 1.5 Amp Trimatron Fan Speed Controls are
ideal for libraries, study rooms and any area where
ceiling fan noise could become distracting. Full
range 5-amp fan speed controls also available
• Wire leads provided for fast, easy assembly
and wiring
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
1.38
(35.1)
1.73 (44.0)
6639-W
C
Download from Www.Somanuals.com. All Manuals Search And Download.
32
INCANDESCENT LIGHTING CONTROLS • 500–600 WATTS • 120V AC 60Hz
Residential Grade Lighting Controls
Incandescent Lighting Controls
Toggle Dimmers 600 Watts 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
COLOR*
(Basic Cat. No. Denotes Brown)
Single Pole Toggle Dimmer
6641
6643
6691
6693
I, W,
I, W
3-Way Toggle Dimmer
Single Pole Illuminated Toggle Dimmer
3-Way Illuminated Toggle Dimmer
Clear
Clear
Decora® 911 Flasher 500 Watts 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
COLOR*
Decora 3-Position Emergency Flasher Rocker Switch
911
I, W, A
1.75 (44.5)
1.90
(48.3)
6641-W
2.39 (60.7)
1.43
(36.4)
911-W
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
• UL Listed (File #E-31373)
• CSA Certified (File #LR-3413)
Toggle Dimmers
• Easy-to-install shallow design replaces standard
switch in single wallbox
• Backed by a Limited Five-Year Warranty
• Built-in radio/TV interference filter
*COLOR
• Positive ON/OFF action with smooth, full-range
brightness control
911 Switch
• 911 replaces standard single-pole switch and
alerts neighbors and helps emergency personnel
locate a house quickly
Basic Cat. No. denotes Brown where indicated. Add
suffix to catalog number as follows for other colors:
Ivory (-I), White (-W), and Almond (-A).
MATERIAL CHARACTERISTICS
• 911 Switch has standard ON/OFF operation plus a
special illuminated “FLASH” position that causes
controlled lighting to flash ON and OFF at one sec-
ond intervals
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
C
For answers to technical questions, call Leviton’s Techline at 1-800-824-3005
Download from Www.Somanuals.com. All Manuals Search And Download.
33
INCANDESCENT LIGHTING CONTROLS • 150–500 WATTS • 120V AC 60Hz
Residential Grade Lighting Controls
Specialty Dimmers and Sockets
Incandescent Dimmers 120V AC 60Hz Only U R
DESCRIPTION
CAT. NO.
RATING
COLOR*
Decora 4-Level Step Dimmer
6161
500W
W, I, A
HI-LO Feed-through Lamp-Cord Dimmer
1420
200W
200W
300W
W, I
(Basic Cat. No.
Denotes Brown)
Full-Range Feed-through Lamp-Cord Dimmer
(Individually boxed)#
6250-3
TBI03
W
(Basic Cat. No.
Denotes Brown)
Tabletop Dimmer for plug-in lamps
W
Dimmer Socket 120V AC 60Hz Only U R
DESCRIPTION
Full-Range Compact Dimmer Socket
(1/8 I.P.S Thread and Set Screw)
1.73 (43.4)
1.53
(38.9)
CAT. NO.
6151
RATING
COLOR*
6161-W
150W
(Non-color item)
1.25 (31.7)
Full-Range Compact Dimmer Socket
(1/8 I.P.S Thread and Set Screw)—
Blister Pak Carded
6151-BP
150W
(Non-color item)
All devices are UL Listed and CSA Certified except where indicated by#
1.50 (38.1)
6151
SPECIFICATIONS AND FEATURES
TESTING AND CODE COMPLIANCE
Four-Level Step Dimmer
• Eliminates guesswork — user selects one of four
preset lighting levels (25%, 50%, 75%, 100%)
• Easily installs in place of single-pole switch
• LED indicates selected level of brightness
• UL Listed (File #E-3810) – 6151; (File #E-7458) –
1420; (File #E-7442) – 6250-3
• CSA Certified (File #LR-1863) – 6151;
(File #LR-3413) – 1420
• Backed by a Limited Five-Year Warranty
• Sleek designer styling; can be ganged with other
Decora devices
*COLOR
Basic Cat. No. denotes Brown where indicated. Add
suffix to catalog number as follows for other colors:
Ivory (-I), White (-W).
Lamp Cord and Socket Dimmers
• Compact Dimmer Socket interchangeable with
standard lampholder for dimmer conversion
(eliminates need for expensive 3-way bulbs)
• Full-Range Feed-Through Lamp Cord Dimmer
provides full-range dimming with positive ON/OFF
action in a completely insulated plastic housing
MATERIAL CHARACTERISTICS
Environmental: Flammability UL-94, V2 Rating
Operating Temperature: 32°F to 130°F
C
Download from Www.Somanuals.com. All Manuals Search And Download.
34
|
