20” Digital / Analog
LCD TV
Owner’s Manual
LC200SL8 A
LC200SL8
TO RECEIVE DIGITAL/ANALOG SIGNAL,
YOU MUST CONNECT ANTENNA.
IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR
VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.com
© 2007 Funai Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this TV through openings as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts specified by
the manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
TV, ask the service technician to perform routine safety checks to
determine that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the TV.
c. If the TV has been exposed to rain or water.
23. WALL OR CEILING MOUNTING - This TV product should be
mounted to a wall or ceiling only as recommended by the
manufacturer.
d. If the TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance, this
indicates a need for service.
5Precautions
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment
may cause harmful interference unless the modifications are expressly approved in the manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC WARNING
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the
building as close to the point of cable entry as practical.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
NTRODUCTION
LOCATION
I
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the
unit. Do not place the unit on a carpet because this will block the ventilation holes.
• Install the unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving the unit to locations where temperature differences are extreme.
• Be sure to unplug the AC power cord from the outlet before carrying the unit.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug the power cord immediately and take the unit to our authorized service center for
servicing.
• Do not place anything directly on top of the unit.
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You
should record the number and other vital information here and retain this book as a permanent record of your purchase to aid
identification in case of theft.
date of purchase
dealer purchase from
dealer phone No.
model No.
serial No.
dealer address
Note about recycling:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
5Supplied Accessories
owner’s manual
(1EMN22073A)
remote control
(NF600UD)
batteries
(AA x 2)
• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free
customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
Contact your local electronics store for these items.
5Symbols Used in this Manual
The following is the description for the symbols used
in this manual.
5Tilt Stand
You can adjust the stand to change the angle
of the TV (-2.5° to 10°).
Description refers to:
10°
-2.5°
: Digital TV operation
: Analog TV operation
DTV
TV
• If neither symbol appears under the function
heading, operation is applicable to both.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5Features
5Contents
• DTV/TV/CATV
INTRODUCTION
- You can use your remote control to select channels which
are broadcast in digital, conventional analog, standard
definition, and high definition formats. Also, cable
subscribers can access their cable TV channels.
• Program Information Display (DTV only)
- You can display the title, contents and other information
of the current DTV program on the TV screen.
• Auto Channel Scan
Important Safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tilt Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attaching a Wall Mount Bracket (sold separately) . . . . . . . . . . . . . . . . . . . . . . . . 8
- This unit automatically scans and memorizes channels
available in your area, eliminating difficult setup
procedures.
CONNECTION
• V-chip
Basic Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
- This feature allows you to block children’s access to
inappropriate programs.
• Closed Caption Decoder
INITIAL SETTING
- Built-in closed caption decoder displays text for closed
caption supported programming.
• MTS/SAP Tuner
- Audio language can be selected from the remote control.
• Auto Shut Off Function
- If there is no signal input from the antenna terminal and
no operation for 15 minutes, the unit will turn itself off
automatically.
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Auto Channel Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Language Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WATCHING TV
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Switching Each Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TV Screen Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
• Sleep Timer
- This feature will automatically turned off the power of the
unit at a specific time.
• Choices for On-screen Language
- Select your on-screen language:
English, Spanish or French.
OPTIONAL SETTING
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DTV Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DTVCC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Back Light Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Color Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
• Stereo Sound Function
• PLL Frequency Synthesized Tuning
- Provides free and easy channel selection and lets you tune
directly to any channel using the channel number buttons
on the remote control.
• Component Video Input
• S-video Input
• AV Input
• Digital Audio Coaxial Output
TROUBLESHOOTING
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
INFORMATION
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Electrical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Other Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
© 2007 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded
or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai.
Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without
the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express
written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing
contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the
trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall
aggressively enforce its intellectual property rights to the fullest extent of the law.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
NTRODUCTION
I
5Remote Control Function
1. POWER button (p12)
Press to turn the unit on and off.
2. MUTE button (p15)
10. RETURN button
Press to return to previous menu
operation.
1
2
3
11
Press to turn the sound on and off. 11. INPUT button (p16)
3. SLEEP button (p18)
Press to activate the sleep timer.
4. Number buttons (p15)
• Press to select channels.
-/ENT. button
• Press to access connected an
external device like a DVD player
or VCR.
• Press to switch between the
digital mode (DTV) and analog
mode.
12
13
14
15
4
• Press to shift the minor channel
from the major channel.
+100 button
12. DISPLAY button (p17)
Digital Mode (DTV)
5
6
• Press to select 100 or higher
channels. (CATV)
• Press to search if there are minor
channels on the currently selected
major channel. (DTV)
• Press to display the channel
information, signal type and TV
setting.
7
8
Analog Mode (TV)
• Press to display the channel
number, signal type and TV
setting.
External Input Mode
• Press to display the external
input mode, signal type and TV
setting.
5. CH. K/L buttons (p15)
Press to select channels and the
external input mode.
9
10
X
/
Y
6. VOL.
buttons (p15)
Press to adjust the volume.
7. ENTER button (p12)
Press to decide the command of
setting when the main menu is
displayed.
13. AUDIO button (p16)
Digital Mode (DTV)
• Press to select the audio
language.
8. SETUP button (p13)
Press to display the main menu.
Analog Mode (TV)
K
L
9.
s
/
B
/
/
buttons (p12)
• Press to select the audio mode.
14. SCREEN MODE button (p18)
Press to select aspect ratio
available for the TV screen.
15. CH. RETURN button (p15)
Press to return to previous channel.
Press to move left/ right/ up/
down through the items.
5Installing the Batteries
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
1
2
3
Battery Precautions:
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can overheat and rupture.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5Control Panel
1
2
3
4
5
1. SETUP button (p13)
Press to display the main menu.
X
Y
2. VOLUME
/
buttons (p15)
X
Y
Press to adjust the volume or move right( )/left(
through the main menu items.
)
SETUP
VOLUME
CHANNEL
INPUT
POWER
K
L
3. CHANNEL
/
buttons (p15)
Press to select channels or move up/down through the
main menu items.
4. INPUT button (p16)
top of the unit
• Press to access connected an external device like a
DVD player or VCR.
• Press to switch between the digital mode (DTV) and
analog mode.
5. POWER button (p12)
Press to turn the unit on and off.
6. Infrared Sensor Window
Receives infrared rays transmitted from the remote
control.
6
5Rear Panel
1. ANT jack (p9)
RF coaxial cable connection for your antenna or cable
box.
2. HEADPHONE jack
Headphone connection for personal listening.
3. COMPONENT and AUDIO input jacks (p10)
Component video cable connection for an external
device.
Use component video and audio output jacks of an
external device.
4. AUDIO input jacks (p10)
RCA audio cable connection for an external device.
5. VIDEO input jack (p11)
RCA video cable connection for an external device.
6. S-VIDEO input jack (p10)
S-video cable connection for an external device.
7. COAXIAL (digital audio) output jack (p11)
Digital audio coaxial cable connection for a decoder or
an audio receiver.
Use digital audio input jack of an external device.
8. AC power cord
1
rear of this unit
VIDEO
2
COMPONENT
Pb
AUDIO
Y
Pr
VIDEO
L
L
R
R
1
2
3
AUDIO
S-VIDEO
VIDEO
COAXIAL
side of the unit
Connect to a standard AC outlet to supply power to
this unit.
4
5
6
7
8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
NTRODUCTION
I
5Attaching a Wall Mount Bracket (sold separately)
The following is a description of the method for attaching a wall mount to this unit.
When performing this operation, refer to the instruction manual included with the wall mount kit.
#
CAUTION
• Any damage caused by incorrectly attempting to mount this unit is not covered under the terms of the manufacturers warranty.
• This unit may be used only with VMFb manufactured by CSAV.
• Use with other wall mounts may result in instability causing possible injury.
You need the following wall mount kit for this unit.
Vision Mount LCD Mounts
Model number: VMFb
2
rear of this unit
*
1 and 2 indicate the
position of the screw holes
on this unit.
1
1
stand
Turn this unit over and place it screen-first onto a table
which has a soft cloth draped over it.
Place this unit in a way so that the stand hangs over
the edge of the table.
Attach this unit to the wall.
1
2
3
4
Note:
• Refer to the instruction manual included with the wall mount
kit when securing this unit to the wall.
Note:
• Make sure to use a table which can support the weight of this
unit and is larger than this unit.
* If you want to attach the stand of this unit again,
insert the stand slowly as illustrated below and drive
M4 screws in the 4 threaded holes ( ).
• Make sure the table is in a stable location.
1
Remove the stand from this unit.
Unscrew the M4 screws indicated by 1 and remove the
stand. Please be careful with the unit after you remove
the stand.
1
Note:
• The M4 screws and stand you have removed are necessary
for reattachment at a later date. Make sure to keep them in a
safe place.
Attach the monitor plate to this unit using the 4 bolts
included with the wall mount kit.
You do not need to use the lock washers for mounting
this unit.
Note:
2
• Only use the screw holes indicated by
unit.
for mounting this
• For instructions on how to attach the monitor plate, refer to
the instruction manual included with the wall mount kit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ONNECTION
C
Cables not included.
Please purchase the necessary cables at your local store.
5Basic Connection
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
[Antenna Cable Connection]
When connecting the unit to an antenna or cable TV company (without cable/satellite box)
Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
e.g.)
VHF / UHF
antenna
rear of this unit
RF coaxial cable
or
cable TV
company
*Once connections are completed, turn on the unit and begin initial setup.
Channel scanning is necessary for the unit to memorize all available channels in your area.
(Refer to “Initial Setup” on page 12.)
Note:
• For your safety and to avoid damage to device, please unplug the RF coaxial cable from the antenna input jack before moving the unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than set-
top versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CATV installer.
[Connection to Cable Box or Satellite Box]
Connect the RF coaxial cable on your home outlet to the input jack of the cable/satellite box.
Use another RF coaxial cable to connect the antenna input jack of the unit to the output jack of the cable/satellite box.
e.g.)
rear of this unit
satellite
dish
cable/satellite box
ANT. IN RF OUT
or
cable TV
company
RF coaxial cable
RF coaxial cable
*Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ONNECTION
C
Cables not included.
Please purchase the necessary cables at your local store.
5External Device Connection
[Component Video Cable Connection]
Component video connection offers better picture quality for video devices connected to the unit.
Use a component video cable to connect the unit to external video devices equipped with component video output
jacks.
If you connect to the unit’s component video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO2.
component
video cable
rear of this unit
(green)
(blue)
(red)
VIDEO 2
COMPONENT
AUDIO
AUDIO
L
L
R
R
Y
Pb
Pr
VIDEO 1
e.g.)
S-VIDEO
VIDEO
COAXIAL
Y
Pb
Pr
COMPONENT VIDEO OUT
AUDIO OUT
L
R
DVD player with the component
video output jacks
(green) (blue) (red)
RCA audio cable
Note:
• This unit accepts 480i / 480p / simplified 1080i video signals.
• Simplified 1080i video signal differs to the original 1080i video signal because it is displayed after converted into 480p signal.
[S-video Cable Connection]
S-video connection offers good picture quality for video devices connected to the unit.
Use an S-video cable to connect the unit to external video devices equipped with S-video output jack.
If you connect to the unit’s S-video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1.
rear of this unit
VIDEO 2
COMPONENT
Pb
AUDIO
AUDIO
L
L
R
R
Y
Pr
VIDEO 1
e.g.)
S-VIDEO
VIDEO
COAXIAL
S-VIDEO
OUT
AUDIO OUT
L
R
DVD player with the S-video
output jack
S-video cable
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Cables not included.
Please purchase the necessary cables at your local store.
[Video Connection]
Video connection offers standard picture quality for video devices connected to the unit.
If you connect to the unit’s video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO1.
When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack.
rear of this unit
VIDEO 2
COMPONENT
Pb
AUDIO
AUDIO
L
L
R
R
Y
Pr
VIDEO 1
e.g.)
S-VIDEO
VIDEO
COAXIAL
AUDIO OUT
VIDEO
OUT
L
R
camcorder
video game
RCA video cable
VCR
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
[Digital Audio Output Connection]
If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound.
rear of this unit
VIDEO 2
COMPONENT
AUDIO
AUDIO
L
L
R
R
Y
Pb
Pr
VIDEO 1
e.g.)
S-VIDEO
VIDEO
COAXIAL
DIGITAL AUDIO
COAXIAL IN
Dolby Digital decoder
digital audio coaxial cable
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
NITIAL SETTING
I
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
Note:
5Initial Setup
• If you connect the cable system directly, contact the CATV
This section will guide you through the unit’s initial setting which includes
installer.
selecting a language for your on-screen menu and “AUTO PRESET CH”, which
automatically scans and memorizes viewable channels.
• If you press [POWER] or [SETUP] during “AUTO PRESET CH”,
this setting will be canceled.
Before you begin:
• The initial auto channel scan function can be executed for
either TV/DTV or CATV only once. If you want to scan both
TV/DTV and CATV, you need to select “CHANNEL SETUP” in
the main menu to scan and memorize other channels after
initial presetting is completed. (Refer to page 13.)
• You can cancel or exit the initial “AUTO PRESET CH” menu by
pressing [SETUP].
Make sure if the unit is connected to antenna or cable.
After making all the necessary connections, press
1
[POWER] to turn on the unit.
• When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
“HELPFUL HINTS” appears. Follow the instructions listed on
the TV screen.
• This operation may take a few moments.
K
L
/
Use [Cursor
] to select the on-screen language
2
3
from the choices on the right side of the TV screen.
(ENGLISH / ESPAÑOL / FRANÇAIS)
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF THE
ANTENNA / CABLE / SATELLITE IS
PROPERLY CONNECTED.
2. DID YOU PERFORM “AUTO PRESET CH”?
3. PLEASE REFER TO FRONT PAGE OF THE
OWNER’S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.
SELECT LANGUAGE
SELECCIONE EL IDIOMA
CHOISIR LA LANGUE
ENGLISH
ESPAÑOL
FRANÇAIS
or
:
:
:
K ,
,
K ,
,
K ,
,
L
L
L
:
:
:
SELECT
SELECCIONE
CHOIX
SET ENTER
AJUSTE ENTER
VALIDER ENTER
• “INITIAL SETUP“ menu on step 3 will be displayed in
the selected language after you press [ENTER].
K
L
/
Use [Cursor
] to select “AUTO PRESET CH(TV/DTV)”
for TV channels or “AUTO PRESET CH(CATV)“ for CATV
channels, then press [ENTER].
- INITIAL SETUP -
or
PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
• Scanning and memorizing the channels automatically
start.
25
AUTO PRESET CH(TV/DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel in the broadcasting
will be displayed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5Main Menu
5Auto Channel Scan
This section describes the overview of the main menu displayed when you
press [SETUP]. For more details, see the reference page for each item.
The main menu consists of the function setting items below.
If you switch wires (e.g., between antenna and CATV) or if you move the TV
to a different area after the initial setting, or if you restore the DTV channel
you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
Press [SETUP] to display the main menu.
Press [SETUP].
1
e.g.) digital TV mode
-
TV SETUP
-
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
Use [Cursor K/L] to select “CHANNEL SETUP”, then
2
press [ENTER].
e.g.) digital TV mode
-
TV SETUP
-
• PICTURE
You can adjust the picture quality.
(Refer to “Picture Adjustment” on page 20.)
PICTURE
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
• CHANNEL SETUP
You can automatically scan the viewable channels and
remove those that are undesired.
(Refer to “Auto Channel Scan” on page 13.)
• V-CHIP SETUP
You can set the viewing limitations.
(Refer to “V-chip” on page 24.)
Use [Cursor K/L] to select your desired preset type,
then press [ENTER].
3
e.g.) digital TV mode
• LANGUAGE
- CHANNEL SETUP -
ADD/DELETE(DTV)
You can change the language (English, Spanish,
French) displayed on the main menu.
(Refer to “Language Selection” on page 14.)
or
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
• CAPTION
You can change the display format for closed caption,
which displays the dialogue of a TV program or other
information across the TV screen.
(Refer to “Closed Caption” on page 20.)
• When aerial antenna is connected, select “AUTO
PRESET CH(TV)”, “AUTO PRESET CH(DTV)” or “AUTO
PRESET CH(TV/DTV)”.
• When connected to CATV, select “AUTO PRESET CH
(CATV)”.
• Scanning and memorizing the channels automatically
start.
• BACK LIGHT
You can set the desired brightness mode.
(Refer to “Back Light Setting” on page 23.)
• COLOR TEMP.
You can adjust color temperature (“NORMAL”, “WARM”,
“COOL”).
e.g.) digital TV mode
(Refer to “Color Temperature” on page 23.)
D25
• DTVCC
In addition to the basic closed caption described
on page 20, DTV has its own closed caption called
DTVCC.
AUTO PRESET CH(DTV)
(Refer to “DTV Closed Caption” on page 21.)
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
• When you selected “AUTO PRESET CH(TV/DTV)”, the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed.
If there is no analog channel, the lowest memorized
digital channel will be displayed.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
NITIAL SETTING
I
5Language Selection
Note:
• If you connect the cable system directly, contact the CATV
installer.
You can choose English, Spanish, or French as your on-screen language.
• If you press [POWER] or [SETUP] during auto channel scan,
the setting will be canceled.
• When no channel can be received by auto channel scan,
“NO TV SIGNALS” will be displayed on the TV screen.
Press [SETUP] to display the main menu.
1
• Channel settings will be saved even if the power fails.
• If you have Spanish or French menus and need English,
press [SETUP]. Use [Cursor K/L] to select “IDIOMA”
or “LANGAGE”. Press [ENTER] to select “ENGLISH”. Press
[SETUP] to remove the main menu.
• With regard only to the digital channel, even after the
scanning is complete if you unplug the AC power cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.
Use [Cursor K /L] to select “LANGUAGE”, then press
[ENTER] repeatedly to change the setting.
2
e.g.) digital TV mode
-
TV SETUP
-
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
[ENGLISH]
[OFF]
BACK LIGHT
COLOR TEMP.
DTVCC
[BRIGHT]
[NORMAL]
or
[ENGLISH]
[ESPAÑOL]
[FRANÇAIS]
Press [SETUP] to exit.
3
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ATCHING TV
W
5Channel Selection
5Volume Adjustment
This section describes how to adjust the volume. The mute function, which
turns the sound off and on, is also described.
K
Select channels by pressing [CH. /L] or [the Number buttons].
K
X
Y
• To select the memorized channels, use [CH. /L] or
Use [VOL.
/
] to adjust the audio volume.
[the Number buttons].
• To select the non-memorized channels use
[the Number buttons].
or
To Use [the Number buttons]
TV
VOLUME
20
- When selecting analog channel 12
• The volume bar will be displayed at the bottom of the
TV screen when adjusting the volume.
• The volume bar display will automatically disappear in
a few seconds.
DTV
- When selecting digital channel 12-1
Be sure to press [–/ENT.] before entering the minor
channel number.
Press [MUTE] to turn off and on the sound.
• Press [CH. RETURN] to return to the previously
viewed channel.
MUTE
20
• When you select a channel larger than 100, press
[+100] first. Then use [the Number buttons] to press
the lower 2-digit numbers.
• “MUTE” is displayed on the TV screen for a few
seconds.
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting
far surpasses analog broadcasting in both its picture
and sound quality.
X Y
/
Press [MUTE] again or [VOL.
original volume.
] to recover the
What is the minor channel?
By using high compression technology, digital
broadcasting offers a service that enables multiple
signals to send simultaneously.
Therefore, you can select more than one program per
major channel since digital broadcasting technology
distinguishes between multiple channels broadcast by
a single network.
[Air Time]
18:00
NTSC (analog mode)
ATSC (digital mode)
CH4
No signal
No signal
18:30
19:00
19:30
CH4
(high definition TV)
CH4
CH4
CH4-1
No signal
CH4
CH4
No signal
CH4-1
CH4-2
CH4-2
20:00
20:30
minor channel
major channel
: change automatically
: change manually by using [CH. K/L]
Although, you cannot watch the high definition TV
(HDTV) program, the unit converts the HDTV signal
down to the standard definition TV signal.
Note:
• “NO SIGNAL” will appear on the TV screen after the minor
channel broadcast is over.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ATCHING TV
W
5
Switching Each Mode
5Switching Audio Mode
You can easily switch with the remote control to the DTV (ATSC) and TV
This section describes how to switch the audio in the analog mode and how
to switch the audio language in the digital mode.
(NTSC) or to access an external device when they are connected to the unit.
TV
Press [INPUT] repeatedly to cycle through analog TV,
digital TV, VIDEO1 and VIDEO2.
While receiving an MTS broadcast, press [AUDIO]
repeatedly to cycle through the available audio
channel.
1
[ANALOG MODE]
[DIGITAL MODE]
[VIDEO1]
[MAIN]
[SAP]
[MONO]
[VIDEO2]
MAIN
SAP
MONO
: Outputs main-audio
: Outputs second audio program
: Outputs mono-audio
• To use the video or S-video input jack on the unit,
select “VIDEO1”.
• To use the component video input jack on the unit,
select “VIDEO2”.
• The current mode will automatically disappear in 10
seconds.
DTV
Note:
Press [AUDIO] to display the currently selected
language and the number of available languages.
1
2
• When you switch the analog mode to the digital mode,
it may take a while until the digital channel selection is
completed. The following TV screen is displayed while
switching the mode.
KABC
CH 95-03
A Day of Memories
ENGLISH 1/3
NOW SCANNING
Press [AUDIO] repeatedly to cycle through the available
audio languages.
[ENGLISH]
[SPANISH]
[FRENCH]
• Available languages differ depending on the
broadcast. “OTHER” is displayed when the audio
language cannot be acquired, or the acquired
languages are other than English, Spanish or French.
• The current mode will automatically disappear in 10
seconds.
Note:
• Pressing [AUDIO] does not control external audio device.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5Screen Information
You can display the currently selected channel or other information such as
the audio mode on the TV screen.
DTV
TV
In the digital mode, the detailed broadcasting information for the current
channel such as program title, program guides are displayed.
In the analog mode, the current channel number is displayed.
Press [DISPLAY].
Press [DISPLAY] repeatedly to cycle through the
available display modes.
CH 25
[OFF]
[BROADCASTING INFORMATION]
[PROGRAM GUIDE]
• The current channel number is displayed at the top-
right corner of the TV screen.
• To clear the display, press [DISPLAY] again.
[Broadcasting Information]
• The following information is displayed.
1 channel number
2 broadcast station
3 program title
4 audio language
(Refer to “Switching Audio Mode”on page 16.)
2
3
4
1
KABC
A Day of Memories
ENGLISH 1/3
CH 95-03
[Program Guide]
• The program guide added to broadcasting
information is displayed.
KABC
CH 95-03
A Day of Memories
ENGLISH 1/3
A quarter-century ago, which may now
qualify as the good old days of newsp-
apering, run-of-paper sales accounted
for 80 percent of the industry’s adverti-
sing revenues.
program
guide
Next - Push L Key
Back - Push K Key
Note:
• When the program guide consists of more than 6 lines, use
[Cursor K/ L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• While the program guide is displayed, the closed caption
function is interrupted.
• In external input mode, the following screen is displayed;
e.g.) When an external device is connected to VIDEO1 input
jack.
VIDEO 1
• Available languages differ depending on the broadcast.
• The information display will automatically disappear in 1
minute.
• Pressing [AUDIO] does not control external audio device.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ATCHING TV
W
5TV Screen Display Mode
5Sleep Timer
The sleep timer can be set to automatically turn off the unit after an
incremental period of time.
DTV
2 types of display modes can be selected in the digital mode when the
broadcasting station is sending 16:9 video signal.
Press [SCREEN MODE] repeatedly to switch the TV
aspect ratio.
Press [SLEEP] to set the sleep timer.
1
SLEEP OFF
• Sleep timer display appears on the TV screen.
Press [SLEEP] repeatedly to change the amount of
time until shut off.
2
LETTERBOX
ZOOM
[LETTERBOX]
Display the digital-supported program in full-screen.
Black borders will spread in the upper and lower
screen.
SLEEP 120MIN.
[ZOOM]
Enlarge and display the center area of the digital-
supported program.
• You can set your unit to turn off after a set period of
time (from 30 to 120 minutes).
• Each press of [SLEEP] will increase the time by 30
The right and left side of image will be cut off.
minutes.
Note:
• You may not switch the display mode depending on the
program.
• After set up, the sleep timer display can be called up
for checking by pressing [SLEEP].
To Cancel the Sleep Timer
Press [SLEEP] repeatedly until “SLEEP OFF“ is displayed
on the TV screen.
Note:
• The sleep timer setting display will automatically disappear
in 10 seconds.
• When you disconnect the unit from the AC outlet or when a
power failure occurs, the sleep timer setting will be canceled.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
PTIONAL SETTING
O
5Channel Add/Delete
The channel add/delete function lets you add the channel that was not
added by the auto channel scan due to the reception status at the initial
setting. You can also delete the unnecessary channels.
Press [SETUP] to exit.
6
Press [SETUP] to display the main menu.
1
Note:
• ”ADD/DELETE(DTV)” or “ADD/DELETE” menu will disappear
automatically in about 10 seconds.
• In the digital mode (DTV), you can add or delete channels
only for major channel.
Use [Cursor K/L] to select “CHANNEL SETUP”, then
2
• Once you delete a DTV channel, you cannot recover the
channel without performing auto channel scan again.
(Refer to “Auto Channel Scan” on page 13.)
press [ENTER].
e.g.) digital TV mode
-
TV SETUP
-
PICTURE
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
[ENGLISH]
[OFF]
BACK LIGHT
COLOR TEMP.
DTVCC
[BRIGHT]
[NORMAL]
Use [Cursor K/L] to select “ADD/DELETE(DTV)” or
“ADD/DELETE”, then press [ENTER].
3
e.g.) digital TV mode
- CHANNEL SETUP -
ADD/DELETE(DTV)
or
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
Select the channel you want to add or delete. (Refer to
“Channel Selection“ on page 15.)
e.g.) digital TV mode
4
5
D25
ADD/DELETE : DTV
Use [Cursor s/ B] to select “ADD” or “DELETE”.
or
• To add or delete another channels, repeat steps 4-5.
• Color of channel number displayed at the right top of
the TV screen indicates;
- Blue: The selected channel will be added.
- Red: The selected channel will be deleted.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
PTIONAL SETTING
5Picture Adjustment
O
5Closed Caption
You can adjust brightness, contrast, color, tint and sharpness.
TV
You can view closed captioning (cc) for TV programs, movies and news.
Closed caption refer to text of dialogue or descriptions displayed on-screen
for the hearing impaired.
Press [SETUP] to display the main menu.
1
Press [SETUP] to display the main menu.
1
Use [Cursor K /L] to select “PICTURE”, then press
[ENTER].
2
e.g.) digital TV mode
Use [Cursor K /L] to select “CAPTION”, then press
[ENTER] repeatedly to change the setting.
2
-
TV SETUP
-
PICTURE
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
e.g.) digital TV mode
[ENGLISH]
[OFF]
-
TV SETUP
-
BACK LIGHT
COLOR TEMP.
DTVCC
[BRIGHT]
[NORMAL]
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
[ENGLISH]
[OFF]
BACK LIGHT
COLOR TEMP.
DTVCC
[BRIGHT]
[NORMAL]
or
Use [Cursor K /L] to select the picture quality type you
3
4
want to adjust.
[OFF]
[BRIGHTNESS]
[CONTRAST]
[CAPTION1]
[CAPTION2]
[TEXT1]
[COLOR]
or
[TINT]
[TEXT2]
[SHARPNESS]
[Caption Mode]
CAPTION1 and TEXT1;
Within 5 seconds, use [Cursor s / B] to adjust the
quality.
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
or
(up to 4 lines of script on the TV screen, where it does
not obstruct relevant parts of the picture).
CAPTION2 and TEXT2;
are rarely available and broadcasters use them
only in special conditions, such as when “CAPTION1”
or “TEXT1” is not available.
Cursor
s
Cursor
B
to decrease brightness to increase brightness
BRIGHTNESS
to decrease contract
to decrease color
to add purple
to increase contract
to brighten color
to add green
CONTRAST
COLOR
TINT
• There are 3 display modes according to programs:
to make soft
to make clear
SHARPNESS
Paint-on mode: Displays input characters on the TV
screen immediately.
Pop-on mode: Once characters are stored in
memory, they are displayed all at
once.
Press [SETUP] to exit.
5
Roll-up mode: Displays the characters continuously
by scrolling (max. 4 lines).
Note:
• The picture adjustment setting display will automatically
disappear in 10 seconds.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5DTV Closed Caption
Press [SETUP] to exit.
DTV
3
In addition to the basic closed caption described on page 20, DTV has its
own closed caption called DTVCC. Use this menu to change the settings for
DTVCC.
Note:
Press [SETUP] to display the main menu.
• To show the closed caption on your TV screen, broadcast
signal must contain the closed caption data.
1
• Not all TV programs and commercials have the closed
caption or all types of the closed caption.
• Captions and texts may not match the TV voice exactly.
• Changing channels may delay the closed caption for a few
seconds.
K
Use [Cursor /L] to select “DTVCC“, then press
[ENTER].
2
• Adjusting or muting the volume may delay the closed
caption for a few seconds.
• Abbreviations, symbols and other grammatical shortcuts
may be used in order to keep pace with the on-screen
action. This is not a problem with the unit.
• The caption or text characters will not be displayed while
the main menu or functions display is shown.
• If a black box appears on the TV screen, this means that the
closed caption is set to TEXT mode. To clear the box, select
“CAPTION 1”, “CAPTION 2” or “OFF”.
e.g.) digital TV mode
-
TV SETUP
-
PICTURE
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
[ENGLISH]
[OFF]
BACK LIGHT
COLOR TEMP.
DTVCC
[BRIGHT]
[NORMAL]
• If the unit receives poor quality television signals, the
captions may contain errors, or there might be no captions
at all. Some possible causes of poor quality signals are:
- Automobile ignition noise
- Electric motor noise
K
Use [Cursor /L] to select “CAPTION SERVICE“, then
press [ENTER] repeatedly to change the setting.
3
- Weak signal reception
- Multiplex signal reception (ghosts or screen flutter)
• The unit retains the closed caption setting if the power fails.
- DTVCC -
CAPTION SERVICE [SERVICE1/6]
or
USER SETTING
CAPTION SIZE
FONT STYLE
[ON]
[MIDDLE]
[STYLE1/8]
CHARACTER EDGE [NONE]
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
[SOLID]
[WHITE]
[SOLID]
[BLACK]
Select if you do not want
DTVCC. This is the default.
OFF
Select one of these before
changing any other item in
CAPTION SERVICE
SERVICE1~6 “CAPTION” menu. Choose
“SERVICE1/6” under normal
circumstances.
Press [SETUP] to exit.
4
Note:
• “CAPTION SERVICE” that you can switch differs depending
on the broadcast description.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
PTIONAL SETTING
O
5DTVCC Style
DTV
You can change the style of DTV CC such as font, color or size, etc.
Press [SETUP] to display the main menu.
• CAPTION SIZE
Closed captioning font size can be changed as below.
1
• FONT STYLE
Font style of the displayed caption can be switched as
below.
K
Use [Cursor /L] to select “DTVCC“, then press
[ENTER].
• CHARACTER EDGE
Edge type of the displayed caption can be switched
as below.
2
e.g.) digital TV mode
• FORE COLOR, BACK COLOR
Font and background color of the displayed caption
can be switched as below.
-
TV SETUP
-
PICTURE
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
[ENGLISH]
[OFF]
• FORE OPACITY, BACK OPACITY
Text and background opacity of the displayed caption
can be switched as below.
BACK LIGHT
COLOR TEMP.
DTVCC
[BRIGHT]
[NORMAL]
CAPTION SIZE
FONT STYLE
MIDDLE, LARGE, SMALL
Proportional font used in the
menu screen
STYLE1/8
K
Use [Cursor /L] to select “USER SETTING“, then press
[ENTER] repeatedly to set to “ON”.
3
4
STYLE2/8 Monospaced with serifs
• Items in the dotted box are available only when “USER
SETTING“ is “ON“.
Proportionally spaced with
STYLE3/8
serifs
STYLE4/8 Monospaced with serifs
- DTVCC -
Proportionally spaced
STYLE5/8
CAPTION SERVICE [SERVICE1/6]
or
USER SETTING
CAPTION SIZE
FONT STYLE
[ON]
[MIDDLE]
[STYLE1/8]
without serifs
STYLE6/8 Casual font type
STYLE7/8 Cursive font type
STYLE8/8 Small capitals
CHARACTER EDGE [NONE]
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
[SOLID]
[WHITE]
[SOLID]
[BLACK]
NONE, RAISED, DEPRESSED, UNIFORM,
SHADOW LEFT, SHADOW RIGHT
CHARACTER EDGE
FORE OPACITY
FORE COLOR
K
Use [Cursor /L] to select an item, then press
SOLID, TRANSLUCENT, FLASH
[ENTER] repeatedly to change the setting for the item.
WHITE, BLACK, RED, GREEN, YELLOW,
BLUE, MAGENTA, CYAN, TRANSPARENT
BACK OPACITY
BACK COLOR
SOLID, TRANSLUCENT, FLASH
- DTVCC -
CAPTION SERVICE [SERVICE1/6]
USER SETTING
CAPTION SIZE
FONT STYLE
or
BLACK, RED, GREEN, BLUE, YELLOW,
MAGENTA, CYAN, TRANSPARENT, WHITE
[ON]
[MIDDLE]
[STYLE1/8]
CHARACTER EDGE [NONE]
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
[SOLID]
[WHITE]
[SOLID]
[BLACK]
Press [SETUP] to exit.
5
22
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5Back Light Setting
5Color Temperature
You can set the desired brightness mode.
You can adjust color temperature of the TV screen.
Press [SETUP] to display the main menu.
Press [SETUP] to display the main menu.
1
1
K
K
Use [Cursor /L] to select “BACK LIGHT”, then press
Use [Cursor /L] to select “COLOR TEMP.”, then press
2
2
[ENTER] repeatedly to change the setting.
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
e.g.) digital TV mode
-
TV SETUP
-
-
TV SETUP
-
PICTURE
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
CAPTION
BACK LIGHT
COLOR TEMP.
DTVCC
or
[ENGLISH]
[OFF]
[ENGLISH]
[OFF]
[BRIGHT]
[NORMAL]
[BRIGHT]
[NORMAL]
[NORMAL]
[WARM]
[COOL]
[BRIGHT]
[NORMAL]
[DARK]
Press [SETUP] to exit.
Press [SETUP] to exit.
3
3
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
PTIONAL SETTING
O
5V-chip
A. TV Rating
V-chip reads the ratings for programs, then denies access to the programs
which exceed the rating level you set. With this function, you can block
certain programming inappropriate for children.
Use [Cursor K /L] to select “TV RATING”, then press
[ENTER].
4
5
Press [SETUP] to display the main menu.
1
e.g.) digital TV mode
-
V - CHIP SETUP -
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
or
Use [Cursor K /L] to select “V-CHIP SETUP“, then press
[ENTER].
2
e.g.) digital TV mode
-
TV SETUP
-
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE
or
Use [Cursor K /L ] to select the desired rating, then
press [ENTER] repeatedly to switch between “VIEW”
and “BLOCK”.
[ENGLISH]
[OFF]
CAPTION
BACK LIGHT
COLOR TEMP.
DTV CC
[BRIGHT]
[NORMAL]
or
TV-Y
TV-Y7
TV-G
TV-PG (
TV-14
TV-MA (
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
(
)
Use [the Number buttons] to enter the 4-digit
numbers for your password.
)
)
)
3
(
PASSWORD
- - - -
Rating
TV-Y
Category
Appropriate for all children
lower
Appropriate for all children 7 and
older
TV-Y7
• When you have not set up your password, enter 0000.
• When the password is correct, the following “V-CHIP
SETUP” menu is displayed.
TV-G
General audience
TV-PG
TV-14
TV-MA
Parental guidance suggested
Unsuitable for children under 14
Mature audience only
See the following description for setting each item.
e.g.) digital TV mode
higher
...
A
“A. TV Rating” D page 24
-
V - CHIP SETUP -
...
B
“B. MPAA Rating”D page 25.
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
A
B
...
C
“C. Change Password”
C
D page 26
Note:
• “DOWNLOADABLE RATING“ will be available when the unit
receives a digital broadcast using the new rating system.
• When you select a rating and set it to “BLOCK”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set the highest rating to “VIEW”, all ratings turn
to “VIEW” automatically.
• If the “PROTECTED PROGRAM” message appears during
your TV viewing, change to a channel that is not blocked.
Then, you can access “V-CHIP SETUP” menu and change the
setting to allow all TV viewing.
• To block any inappropriate programming, set your limits in
both “TV RATING” and “MPAA RATING”.
• The V-chip setting will be retained after a power failure
(except the access code reverts to 0000).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
B. MPAA Rating
MPAA Rating is the rating system created by MPAA (Motion Picture
Association of America).
[To Set the Sub Ratings]
As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further
set the sub ratings to block specific elements of
programming. To set the sub ratings, follow the steps
below.
Use [Cursor K /L] to select “MPAA RATING”, then press
[ENTER].
4
e.g.) digital TV mode
-
V - CHIP SETUP -
Use [Cursor K /L ] to select the desired main rating,
then press [ENTER] twice to show its sub ratings.
1
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
or
or
TV-Y
TV-Y7 (DLSV) [VIEW]
TV-G [VIEW]
[VIEW]
TV-PG (DLSV) [BLOCK]
TV-14 (DLSV) [BLOCK]
TV-MA (DLSV) [BLOCK]
Use [Cursor K /L], then press [ENTER] repeatedly to
change the setting.
5
Use [Cursor K /L ], then press [ENTER] repeatedly
to change the setting.
2
G
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
or
e.g.) TV-PG
PG
PG-13
R
NC-17
X
TV-PG
[BLOCK]
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
or
Rating
Category
General audience
G
Parental guidance suggested
PG
Sub Rating
Category
Fantasy Violence
Rating
TV-Y7
Unsuitable for children under 13
PG-13
FV
V
Restricted; under 17 requires accompanying
parent or adult guardian
R
Violence
TV-PG
TV-14
TV-MA
S
Sexual Situation
Coarse Language
No one under 17 admitted
Mature audience only
NC-17
X
L
D
Suggestive Dialogue
TV-PG, TV-14
Press [SETUP] to exit.
6
Press [SETUP] to exit.
6
Note:
• Blocked sub ratings will appear beside the main rating
category in “TV RATING” menu.
• You cannot block a sub rating (D, L, S or V) if the main rating
is set to “VIEW”.
• Changing the category to “BLOCK” or “VIEW” automatically
changes all its sub ratings to the same (“BLOCK” or “VIEW”).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
PTIONAL SETTING
O
C. Chhaanngge Paasssswoorrdd
Although the default code “0000” is supplied with the unit, you can set
your own password.
Use [Cursor K /L] to select “CHANGE PASSWORD”, then
press [ENTER].
4
e.g.) digital TV mode
-
V - CHIP SETUP -
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
or
Press [the Number buttons] on the remote control to
enter the new 4-digit password.
• Enter password again in “CONFIRM PASSWORD.”
space.
5
6
NEW PASSWORD
_
_
_
_
CONFIRM PASSWORD
_
_
_
_
Press [SETUP] to exit.
Note:
• Make sure new password and confirm password must be
exactly the same. If they are different, the space is cleared
for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs. If you forget the
password, unplug the power cord for 10 seconds to restore
the password to 0000.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ROUBLESHOOTING
T
5Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this owner's manual, check the following chart
once before calling for service.
Symptom
Remedy
No power
• Be sure the power cord is plugged in.
• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
reset itself.
No picture or sound
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on again.
No color
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Adjust the “COLOR”in the main menu.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• Adjust “CONTRAST”and “BRIGHTNESS”in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted
Weak picture
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Adjust “CONTRAST”and “BRIGHTNESS”in the main menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture blurred
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Bars on screen
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on
screen
• Move the unit away from nearby electric appliances. Turn off the power and wait
30 minutes before turning it back on.
• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some
channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor
• View other TV channels. The problem might be limited to the broadcasting station.
No reception of digital signals • Make sure auto channel scan has been completed (Refer to “Auto Channel Scan”on
page 13).
Auto channel scan must be completed when you set up the unit for the first time
or move it to a location where previously unavailable channels are broadcast.
• The selected channel may not be broadcasting.
• When auto channel scan is interrupted and not completed, some channels will not
be received. Make sure to complete (Refer to “Auto Channel Scan”on page 13).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ROUBLESHOOTING
T
Symptom
Remedy
The entered channel number
changes automatically
• Many digital channels have alternate channel numbers. The unit changes the
numbers automatically to the ones signifying the broadcasting stations. These are
the numbers used for analog broadcasts.
Remote control does not work • Check the antenna or cable connection to the main unit.
• Check the batteries of the remote control.
• Check if there is an obstacle between the infrared sensor window and the remote
control.
• Test the signal output. If OK, then possible infrared sensor trouble.
(Refer to “IR Signal Check”on page 28.)
• Aim the remote control directly at the infrared sensor window on the front of the
unit.
• Reduce the distance to the unit.
• Re-insert the batteries with their polarities (+/– signs) as indicated.
Problems with Closed Caption Feature
Misspelled captions are
displayed.
• Closed captioning production companies may broadcast programs without
correcting the misspelling in a live broadcast.
Captions are not entirely
displayed, or captions are
delayed behind the dialogue.
•
Captions that are delayed a few seconds behind the actual dialogue are common for
live broadcasts. Most captioning production companies can display a dialogue to a
maximum of 220 words per minute. If a dialogue exceeds that rate, selective editing is
used to insure that the captions remain up-to-date with the current TV screen dialogue.
Captions are displayed as a
white box.
No caption is displayed in the
closed caption-supported
program.
• Interference from buildings or weather conditions may cause captioning to be
incomplete.
• Broadcasting station may shorten the program to insert advertisement. The closed
caption decoder cannot read the information of the shortened program.
No caption is displayed
when playing the videotape
containing captions.
• The videotape may be illegally copied, or the caption signal might not have been
read during copying.
Black box is displayed in the
TV screen.
• “Text”mode is selected for caption. Select “CAPTION1”, “CAPTION2”or “OFF”.
Note:
• The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a fixed point of
blue, green or red. This is not to be considered a defect in the LCD screen.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this owner's manual for more
details on correct operations.
5Maintenance
Cabinet Cleaning
IR Signal Check
• Wipe the front panel and other exterior surfaces of the unit with a soft
cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the
unit. Such chemicals may cause damage and discoloration to the exposed
surfaces.
If the remote control is not working properly, you can use an AM radio or
digital camera (including a cellular phone with built-in camera) to see if it
is sending out an infrared signal.
• With an AM radio:
Tune the AM radio station to a non-broadcasting
frequency. Point the remote control towards it,
push any button and listen. If the sound from
the radio flutters, it is receiving the remote
control’s infrared signal.
Panel Cleaning
Wipe the panel of the unit with a soft cloth. Before cleaning the panel,
disconnect the power cord.
• With a digital camera
(including built-in cell
Servicing
phone cameras):
Should your unit become inoperative, do not try to correct the problem
yourself. There are no user serviceable parts inside. Turn off the unit,
unplug the power cord and call our toll free customer support line found on
the cover of this manual to locate an authorized service center.
Point a digital camera towards the remote control.
Push any button on the remote control and look
through the digital camera. If the infrared light
appears through the camera, the remote control is
working.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
NFORMATION
I
5Glossary
ATSC
Dolby Digital
Password
Acronym that stands for Advanced
Television Systems Committee and the
The system developed by Dolby
Laboratories to compress digital sound. It
A stored 4-digit number that allows access
to parental control features.
name of the digital broadcasting standards. offers stereo sound (2ch) or multi-channel
SAP (secondary audio program)
audio.
Aspect Ratio
Second-audio channel delivered separately
from main-audio channel. This audio
channel is used as an alternate in bilingual
broadcasting.
EDTV (enhanced definition TV)
The width of a TV screen relative to its
height. Conventional TVs are 4:3 (in other
words, the TV screen is almost square);
widescreen models are 16:9 (the TV screen
is almost twice as wide as its height).
Enhanced digital format that takes 480-line
progressive signal.
HDTV (high definition TV)
SDTV (standard definition TV)
Ultimate digital format that produces high
resolution and high picture quality.
Standard digital format that is similar to the
NTSC picture quality.
Component Video
This is a video signal format that conveys
each of 3 principal colors of light (red,
blue and green) through different signal
lines. This allows the viewers to experience
picture colors as original as it is. There are
several signal formats, including Y / Pb / Pr
and Y / Cb / Cr.
NTSC
S-video
Acronym that stands for National Television
Systems Committee and the name of the
current analog broadcasting standards.
Offers higher quality images by delivering
each signal, color (c) and luminance (y)
independently of each other through
separate cables.
5Cable Channel Designations
If you subscribe to cable TV, the channels are displayed as 1-135.
Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company.
The following is a chart of common cable channel designations.
CATV channel
5A
1
I
2
2
J
3
3
K
4
4
L
5
5
M
26
6
6
N
7
7
O
28
8
8
P
9
9
Q
30
10
10
R
11
11
S
12
12
T
13
13
U
A
14
V
B
C
16
D
17
E
18
F
19
G
20
H
21
TV Display
CATV channel
TV Display
15
W
36
W+1 W+2 W+3 W+4 W+5 W+6
37 38 39 40 41 42
22
23
24
25
27
29
31
32
33
34
35
CATV channel
TV Display
W+7 W+8 W+9 W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24 W+25 W+26 W+27
43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39 W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84
W+49 W+50 W+51 W+52 W+53 W+54 W+55 W+56 W+57 W+58 A-5 A-4 A-3 A-2 A-1 W+59 W+60 W+61 W+62 W+63 W+64
85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79 W+80 W+81 W+82 W+83 W+84 W+85
106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126
W+86 W+87 W+88 W+89 W+90 W+91 W+92 W+93 W+94
CATV channel
TV Display
127 128 129 130 131 132 133 134 135
5General Specifications
5Electrical Specification
TV format:
Closed caption system:
§15.122/FCC (digital CC) §15.119/FCC (analog CC)
ATSC / NTSC-M TV standard
Sound output: 1W, 8Ω x 2
Channel coverage (ATSC/NTSC):
5Other Specifications
Remote control: Digital encoded infrared light system
Operating temperature:
41°F (5°C) to 104°F (40°C)
Terrestrial
CATV
VHF: 2~13 UHF: 14~69
2~13, A~W, W+1~W+94 (analog W+1~W+84),
A-5~A-1, 5A
Tuning system: Channel frequency synthesized tuning system
Channel access:Direct access keyboard,
Programmable scan, and up/down
Power requirements:
120V AC +/- 10%, 60Hz +/- 0.5%
Power consumption (maximum):
60W
Terminals:
Antenna input: VHF/UHF/CATV
75Ω unbalanced (F-type)
S-video input: Mini DIN 4-pin jack x 1 Y: 1Vp-p (75Ω)
LCD:
Dimensions:
20 inches VGA panel
W: 23 3/8 inches
H: 17 7/8 inches
D: 8 1/16 inches
11.7 lbs.
C: 286mVp-p (75Ω)
1Vp-p (75Ω)
2V rms
(594mm)
(454mm)
(204mm)
(5.3kg)
Video input: RCA jack x 1
Audio input: RCA jack x 4
(input impedance: more than 22kΩ)
Weight:
Component video input:
RCA jack x 3
Y: 1Vp-p (75Ω)
Pb: 700mVp-p (75Ω)
Pr: 700mVp-p (75Ω)
• Designs and specifications are subject to change without notice and
without our legal obligation.
• If there is a discrepancy between languages, the default language will
be English.
Coaxial digital audio output:
RCA jack x1
500mVp-p (75Ω)
(3.5mm)
1
Headphone:
/
8
inches
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year
from the date of original retail purchase. Certain parts and LCD image burn-in are excluded
from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the
date of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO
OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,
missing or if service was attempted by an unauthorized service center. This limited warranty does not
apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during
normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs,
alterations or products not supplied by FUNAI CORP., or damage, which results from accident, misuse,
abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use
such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or
other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL),
ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING
THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY
DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO
PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE
CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY
FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN
SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its
original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE
CENTER. FUNAI CORP. will not reimburse you for any service done by unauthorized service providers
without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact us at:
FUNAI CORPORATION
Customer Service
Tel : 1-800-968-3429
19900 Van Ness Avenue, Torrance, CA 90501
Printed in China
A7148UH / A7140UH
1EMN22073A ****
Download from Www.Somanuals.com. All Manuals Search And Download.
|