OWNER’S
MANUAL
DVD PLAYER with VIDEO CASSETTE RECORDER
DVC800C
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
-
-
TOLL FREE : 1 800 968-3429
Please read before using this equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instruc-
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-dis-
charge unit, connection to grounding electrodes, and
requirements for the grounding electrode. (Fig. A)
tions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
FIGURE A
ANTENNA
LEAD
WIRE
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
cleaners. Use
a
damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the pos-
sibility of the loss of an authorization code for a CATV
converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference
to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. Attachments - Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a swim-
ming pool, and the like.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
NEC – NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
14. Lightning - For added protection for this video product
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This
will prevent damage to the video product due to lightning
and power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
8. Accessories - Do not place this video product on
an unstable cart, stand, tripod, bracket, or table.
The video product may fall, causing serious
injury to a child or adult, and serious damage to
the appliance. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the video product. Any mounting of the appliance
should follow the manufacturer's instructions and should use
a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19. Damage Requiring Service - Unplug this video product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
9. Ventilation - Slots and openings in the cabinet are provid-
ed for ventilation and to ensure reliable operation of the
video product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the video product on a
bed, sofa, rug, or other similar surface. This video product
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer's instructions have been adhered to.
10. Power Sources - This video product should be operated
only from the type of power source indicated on the mark-
ing label. If you are not sure of the type of power supply
to your home, consult your appliance dealer or local power
company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is
equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety fea-
ture. If you are unable to insert the plug fully into the out-
let, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying par-
ticular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by follow-
ing the operating instructions. Adjust only those controls
that are covered by the operating instructions as an improp-
er adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any way.
f. When the video product exhibits a distinct change in per-
formance this indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs
to this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
13. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the video product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with regard to
22. Heat - This video product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
EN
–
–
3
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
The serial number of this product may be found on the back of the DVD/VCR player. This serial number is
unique to your machine. You should record the number and other vital information here and retain this book as
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by claims of certain U.S. patents and
other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copy-
right protection technology must be authorized by Macrovision Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SUPPLIED ACCESSORIES
Coaxial Cable
Remote control
(NA200UD)
Two AA batteries
A/V cables
(approx. 3 feet (100 cm)
long) (WPZ0102TM015)
WPZ0901TM002
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
VCR
: refers to playback of video cassette tapes.
DVD
: refers to playback of DVD video discs.
CD
: refers to playback of audio CDs.
MP3
: refers to playback of MP3 discs.
EN
–
–
4
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
ꢀ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ꢀ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
PLAYING A DVD VIDEO OR AN AUDIO CD . . . . . . . . . . 23
USING THE DVD MENUS . . . . . . . . . . . . . . . . . . . . . . . . . 23
USING THE TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . 24
PAUSING PLAYBACK OR DISPLAYING A STILL
PICTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
RESUMING PLAYBACK FROM THE POINT WHERE
PLAYBACK STOPPED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
STEPPING THROUGH FRAMES . . . . . . . . . . . . . . . . . . . . 24
FAST FORWARD/REVERSE . . . . . . . . . . . . . . . . . . . . . . . . 25
SLOW MOTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
STARTING FROM A DESIRED TRACK . . . . . . . . . . . . . . . 25
PLAYING FROM A DESIRED TITLE OR A CHAPTER . . . 25
STARTING FROM A DESIRED TIME COUNT. . . . . . . . . . 26
MARKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RANDOM (Audio CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PROGRAM (Audio CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ZOOM PLAYBACK (enlargement on-screen) . . . . . . . . . . . . 28
PLAYING AN MP3 DISC. . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CHANGING THE ON-SCREEN DISPLAY DURING
ꢀ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4
ꢀ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ꢀ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ꢀ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PLAYABLE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ꢀ OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 9
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 12
LOADING THE BATTERIES. . . . . . . . . . . . . . . . . . . . . . . . 12
ꢀ VIDEO/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . 13
ꢀ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DVD/VCR TO TV CONNECTION. . . . . . . . . . . . . . . . . . . . 14
SETTING THE CH3/CH4 SWITCH . . . . . . . . . . . . . . . . . . . 14
CONNECTING TO A TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT
JACK OR COMPONENT VIDEO IN JACKS. . . . . . . . . . . . 14
CONNECTING TO AN AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT
DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CONNECTING TO A DOLBY DIGITAL DECODER OR
MP3 DISC PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PLAYING A DESIRED TRACK FROM AN MP3 DISC . . . 30
PLAYING AN MP3 DISC RANDOMLY . . . . . . . . . . . . . . . 30
PLAYING AN MP3 DISC IN A PROGRAM. . . . . . . . . . . . . 30
ꢀ SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CHANGING THE AUDIO LANGUAGE OR SOUND
MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CHANGING THE SUBTITLE LANGUAGE . . . . . . . . . . . . 32
CHANGING THE CAMERA ANGLE
(Multi-Angle Pictures). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 33
BLACK LEVEL SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . 33
TruSurround SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ꢀ CHANGING THE SETUP ITEMS. . . . . . . . . . . . . . . . . . . . 34
LANGUAGE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DISPLAY SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
AUDIO SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
PARENTAL LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ꢀ LANGUAGE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . 38
ꢀ TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . 39
ꢀ HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . 40
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
ꢀ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
DTS DECODER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CONNECTING TO AN ANALOG AUDIO. . . . . . . . . . . . . . 16
ꢀ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 17
TO CHANGE THE ON-SCREEN LANGUAGE. . . . . . . . . . 18
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ꢀ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 19
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ꢀ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 20
VIEWING AND RECORDING THE SAME PROGRAM. . . 20
OTR (One Touch Recording). . . . . . . . . . . . . . . . . . . . . . . . . 20
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 21
ꢀ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 22
MTS (Multi-Channel Television Sound) SYSTEM . . . . . . . . 22
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
REAL TIME TAPE COUNTER. . . . . . . . . . . . . . . . . . . . . . . 23
INDICE
ꢀ CONTROLES DEL FUNCIONAMIENETO Y SUS FUNCIONES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
ꢀ CAMBIO DE VCR/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
ꢀ CONEXIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
DVD/VCR A CONEXIÓN DE TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
AJUSTANDO EL CONMUTADOR CH3/CH4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONECTANDO A UN TV
. . . 46
CONECTADO A UN TV QUE TIENE TOMA DE ENTRADA DE S-VÍDEO o TOMAS DE ENTRADA DE VÍDEO COMPONENTE
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT
. 46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY O DESCODIFICADOR DTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
CONECTANDO A UN AUDIO ANALÓGICO
ꢀ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
PREPARACIÓN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
PREPARACIÓN DE CANAL AUTOMÁTICA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
PREPARACIÓN DE RELOJ
ꢀ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO
EN
–
–
5
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Mode
DVD
¡Dolby Digital sound
¡On-screen display
This player can handle Dolby Digital surround sound
with 5.1 channels when connected to a Dolby Digital
decoder.
Information about the current operation can be displayed
on the TV screen, allowing you to confirm the currently
active functions (such as program playback), on the TV
screen using the remote control.
¡Still/fast/slow/step playback
Various playback modes are available including still pic- ¡DTS (Digital Theater System)
tures, fast forward/reverse, slow motion and step frames.
You can enjoy 5.1 channel surround system developed by
the Digital Theater System co. which reproduces the orig-
inal sound as truthfully as possible.
¡Search
¡Random playback for audio CD and MP3
This player can shuffle the order of tracks to play them in
random order.
Chapter search: Search for a chapter designated by user is
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in any
desired order.
possible.
Title search: Search for a title designated by user is pos-
sible.
Track search: Search for a track designated by user is
¡DVD menus in a desired language
You can display DVD menus in the desired language, if
available on the DVD.
possible.
Time search: Search for a time designated by user is
possible.
¡Screen saver/Auto power-off functions
¡Repeat
Chapter:
The screen saver program starts when there is no input
from the player for five minutes in the stop mode. When
the screen saver program has been activated for 30 min-
utes, the screen saver is automatically turned off.
Repeated playback of the chapter of the
disc being played is possible.
Title:
Repeated playback of the title of the disc
being played is possible.
¡Subtitles in a desired language
You can select the desired language for the subtitle dis-
play, if that language is available on the disc.
Track:
Repeated playback of the track of the disc
being played is possible.
Disc (audio CD): Repeated playback of the entire disc being
¡Selecting a camera angle
(MP3)
played is possible.
You can select the desired camera angle, if the disc con-
tains sequences recorded from different angles.
A-B:
Playback of the section between A and B
(designated by user) is possible.
Album:
Repeated playback of the album of the
MP3 disc being played is possible.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available on
the disc.
¡Zoom
A ×2 and ×4 magnified screen can be displayed.
¡Marker
¡Parental lock
You can set the control level to limit playback of discs
which may not be suitable for children.
A part designated by user can be called back.
¡Resume Play
User can resume playback from the part at which the play
was stopped even if the power is turned off.
¡Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡SRS TruSurround
You can enjoy a stereophonic virtual space on your exist-
ing stereo system.
¡Component Video Out Jacks
Jacks located on the back of the DVD/VCR are used to
send high-quality video to a TV via Component Video In
Jacks.
¡Playing an MP3 disc
You can enjoy MP3 files which are recorded on CD-
R/RW.
¡Direct Search
You can search for the desired title, chapter, and track with
the Number buttons during playback or in stop mode.
¡Dimmer
Brightness of the display can be varied.
This unit employs TruSurround system
of SRS Labs, Inc. as virtual
technology.
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
TruSurround and the
SRS Labs, Inc.
symbol are trademarks of
TruSurround technology is incorporated under license
from SRS Labs, Inc.
EN
–
–
6
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Mode
VCR
¡S-VHS Quasi Playback (SQPB)
(Allows you to view a tape recorded in S-VHS format.)
¡Auto Repeat
Hardware specifications
¡Auto Head Cleaner
¡4 Head HiFi Stereo
¡2 Step Picture Search Operation
¡Index Search
¡Bilingual on-screen menu display selectable in
English, French, or Spanish
¡Time Search
¡181 channel capability PLL frequency synthesiz-
er tuner with direct station call
(A cable converter box may be necessary to view scram-
Recording
¡1Year, 7 events (including Daily and WeeklyTimer
Recording)
bled cable channels.)
Automatic functions
¡OTR (One Touch Recording)
¡Auto power on system
Automatically turns the DVD/VCR on when you insert the
cassette.
¡Digital Auto Tracking (DTR)
PRECAUTIONS
AVOID THE HAZARDS OF
INSTALLATION LOCATION
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your DVD/VCR,
unplug the power cord immediately and take the unit to
our Authorized Service Center for servicing.
• Do not put your fingers or objects into the DVD/VCR
cassette holder.
For safety and optimum performance of your DVD/VCR:
• Install the DVD/VCR in a horizontal and stable posi-
tion. Do not place anything directly on top of the
DVD/VCR. Do not place the DVD/VCR directly on top
of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
on the sides of the DVD/VCR. Avoid locations subject
to strong vibration or strong magnetic fields.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when it is
moved from a cold place to a warm place, or after heating a
cold room or under conditions of high humidity. Do not use
the DVD/VCR at least for 2 hours until its inside is dry.
EN
–
–
7
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
[
]
The following discs can be played back on this
DVD/VCR.
DVD
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback con-
ditions take priority over user operations on this player. If
a function you selected does not run as desired, refer to
the manual accompanying the disc.
Maximum
Playback Time
Disc Type
Logo
Contents Disc Size
Approx. 4 h
(single-sided)
12 cm
Approx. 8 h
(double-sided)
Sound
and
Pictures
DVD
Video
Approx. 80 min
(single-sided)
8 cm
Example
Approx. 160 min
(double-sided)
Title 1
Title 2
12 cm
74 min
20 min
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
Audio
CD
Sound
8 cm
(singles)
This player conforms to the NTSC color system. You can-
not play discs recorded in other color systems such as
PAL or SECAM.
¡Some discs include region codes as shown below.
[
]
AUDIO CD
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on DVD/VCR with the same
region code.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
The following discs cannot be played back on this
DVD/VCR.
¡
DVD with region codes other than 1 or ALL.
¡
DVD-ROM
¡
[
]
DVD-RAM (Never attempt to play back,
otherwise a malfunction may result.)
CD-ROM
MP3
Data on an MP3 is divided into sections called "albums",
and then into subsections called "tracks", each of which is
given an album or track number.
¡
¡
¡
¡
¡
VSD
CDV (Only plays back the audio part.)
CD-G (Only plays back the sound.)
CD-R/CD-RW
(Only plays back discs on which audio CD or
MP3 are recorded.)
Example
Album 1
Album 2
Track 1
Track 2
Track 3
Track 4
Track 1
Track 2
¡
CD-I
(Never attempt to play back, otherwise a mal-
function may result.)
¡
¡
SACD
Photo CD
(Never attempt to play back, otherwise a mal-
function may result.)
¡
Video CD
(Never attempt to play back, otherwise a mal-
function may result.)
Any other discs without compatibility indications
EN
–
–
8
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING CONTROLS AND FUNCTIONS
1
2
3
4
5
6
7 8 9
FRONT PANEL
POWER
VIDEO
L
CHANNEL
DVD OPERATION
OUTPUT
VCR OPERATION
TIMER
SET
AUDIO
R
VCR/TV
CST.IN
OPEN/CLOSE
STOP
SKIP/REV PLAY
FWD/SKIP
STOP/EJECT REW
PLAY
F.FWD REC/OTR
25
23 21
22
19 17 15 13 11
18 16 14 12 10
26
24
20
REMOTE CONTROL
tape in the DVD/VCR. It flashes when all timer
recordings or One-Touch Recordings are finished.
7. POWER Button [page 17]
56
54
27
POWER SPEED AUDIO
28
Press to turn the power on and off.
8. POWER Light
1
4
7
2
5
8
0
3
6
55
53
SKIP/CH.
Lights up when the power is on.
9. VIDEO In Jack
29
VCR/TV
SLOW
Connect a video cable coming from the video out
jack of a camcorder, another VCR, or a video source
(laser disc player, camcorder, etc.) here.
10. AUDIO In Jacks
9
+100
+
10
DISPLAY DVD
VCR
PAUSE
52
50
30
32
34
Connect audio cables coming from the audio out jacks
of a camcorder, another VCR, or an audio source here.
11. TIMER SET Button [page 21]
Press to put the DVD/VCR into standby mode for a
timer recording.
12. CASSETTE IN Light [page 19]
Lights up when a cassette is in the DVD/VCR.
13. VCR/TV Light [page 17]
51
49
31
33
PLAY
STOP
RECORD
MENU
48
46
35
37
39
ENTER
47
36
38
SETUP
TITLE
RETURN
Lights up when the DVD/VCR is in the VCR posi-
tion, and goes off when it is in the TV position.
14. CHANNEL Buttons [page 17]
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
45
43
44
42
SUBTITLE ANGLE REPEAT
A
B
In VCR mode, press to change TV channels on the
DVD/VCR; press to adjust the tracking during nor-
mal or slow motion playback; press to remove verti-
cal jitter in a Still picture.
40
41
1. Disc loading tray
2. DVD OUTPUT Light (Green) [page 13]
15. REC/OTR Button (VCR) [page 20]
Press once to start a recording. Press repeatedly to
start a One-Touch Recording.
This light appears when the DVD output mode is
selected. You can only watch DVDs when the green
DVD OUTPUT Light is on. To make the green DVD
OUTPUT light come on, press the DVD button on
the remote control or the OUTPUT button on the
front panel.
16. F.FWD Button (VCR) [page 17]
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback. (Forward
Search). When setting program (For example:setting
clock or timer program), press to determine your
selection and proceed to the next step you want to
input. Press to determine the setting modes from the
on screen menu. Press to add or delete channel num-
bers during channel preset.
3. VCR OUTPUT Light (Green) [page 13]
This light appears when the VCR output mode is
selected. You can only watch tapes when the green
VCR OUTPUT light is on. To make the green VCR
OUTPUT light come on, the VCR button on the
remote control or the OUTPUT button on the front
panel.
17. PLAY Button (VCR) [page 17]
Press to begin playback. Press to enter digits when
setting program (For example: setting clock or timer
program). Press to select the setting modes from the
on screen menu.
4. CASSETTE COMPARTMENT
5. REC/OTR Light [page 20]
Lights up during recording.
18. REW Button (VCR) [page 18]
6. TIMER SET Light [page 21]
Press to rewind the tape, or to view the picture rapid-
ly in reverse during the playback mode (Rewind
Search). Press to cancel a setting of timer program.
Press to correct digits when setting program (For
This light glows when the DVD/VCR is in standby
mode or off for a timer recording or during a One-
Touch Recording. It flashes if the TIMER SET but-
ton is pressed for a timer recording, but there is no
EN
–
9 –
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
example: setting clock or timer program). Press to
add or delete channel numbers during channel preset.
select the corresponding mode by pressing the
DVD or the VCR button on the remote control.
19. STOP/EJECT Button (VCR) [page 21
]
32. h Button
GEJECT Button
Press to remove the tape from the VCR.
GSTOP Button
Press to stop the tape motion. Press to enter digits
when setting program (For example:setting clock
or timer program). Press to select the setting
modes from the on screen menu.
GDVD mode
Press to view the DVD picture in fast reverse
motion or to reverse playback of an Audio CD.
GVCR mode
Press to rewind the tape, or to view the picture
rapidly in reverse during the playback mode
(Rewind Search). Press to cancel a setting of
timer program. Press to correct digits when setting
program (For example: setting clock or timer pro-
gram). Press to add or delete channel numbers
during channel preset.
20. OUTPUT Button [page 13]
Press to select DVD mode or VCR mode.
G
You can switch the output mode either by pressing
the OUTPUT button on the front panel, or by press-
ing the DVD or the VCR button on the remote con- 33. Stop Button
trol. However, if you press the OUTPUT button
on the front panel first, you need to re-select the
corresponding mode by pressing the DVD or the
VCR button on the remote control.
Press to stop the tape motion. Press to enter digits
when setting program (For example: setting clock or
timer program). Press to select the setting modes
from the on screen menu.
21. FWD/SKIP Button (DVD) [page 25]
Plays back from the beginning of the next chapter or
track. Hold down to fast forward playback.
22. PLAY Button (DVD) [page 23]
Press to begin playback.
34. RECORD Button
Press once to start a recording. Or, press repeatedly
to start a One-Touch Recording.
35. MENU Button
GDVD mode [page 23]
23. SKIP/REV Button (DVD) [page 25]
Plays back from the beginning of the current chapter
or track. Hold down to fast reverse playback.
24. STOP Button (DVD) [page 23]
Stops operation of the disc.
Press to display the menu of the Disc.
GVCR mode [page 17]
Press to access the VCR menu.
36. TITLE Button
37. SETUP Button [page 34]
25. OPEN/CLOSE Button [page 23]
Press to enter the setup mode.
Press to insert discs into or remove them from the tray. 38. ZOOM Button [page 28]
26. Display, Remote Sensor Window
27. SPEED Button [page 20]
Press to select the VCR’s recording speed (SP or SLP)
28. POWER Button
Enlarges part of a DVD-reproduced image.
39. MODE Button [pages 26]
Activates program playback or random playback
mode when playing CDs or MP3. Sets Black level or
SRS TruSurround.
Press to turn the power on and off.
29. Number Buttons
40. SUBTITLE Button [page 32]
GDVD mode [page 25]
Press to select the desired subtitle language.
Press to directly select a Track (Audio CD) for 41. ANGLE Button [page 32]
playback.
Press to change the camera angle to see the sequence
Press to program Tracks (Audio CD) for playback.
GVCR mode [page 25]
being played back from a different angle.
42. REPEAT Button [page 27]
Repeats playback of the current disc, title, chapter or
track.
Press to select TV channels on the DVD/VCR.
To select channels, enter channel numbers as a
two-digit number for the quickest results. For 43. A-B REPEAT Button [page 27]
example, to select channel 6, press 0 then 6.
Repeats playback of a selected section.
44. SEARCH MODE Button
GDVD mode [page 25]
+100 Button:
If you want to select channels 100 and above, press
this button first, then press the last two digits. For
example, to select channel 125, press +100 button
first, then press 2 and 5.
Press to access or remove the Search display,
which allows you to go directly to a specific
Title/Chapter/Track/Time.
GVCR mode [page 19]
30. DISPLAY Button
Press to perform a Time Search or an Index Search.
45. CLEAR/C.RESET Button
GDVD mode [page 26]
GDVD mode [page 13]
Press to access or remove the display screen during
DVD or Audio CD playback.
Press to reset the setting.
GVCR mode [page 18]
Press to reset the counter. Press to exit from the
MENU screen.
GVCR mode [page 13]
Press to access or remove the VCR’s on-screen sta-
tus display.
31. DVD Button [page 13]
46. RETURN Button
Returns to the previous operation.
47. Arrow Buttons
Press to select DVD mode for the remote control.
GYou can switch the OUTPUT mode either by
pressing the OUTPUT button on the front panel, or
by pressing the DVD or the VCR button on the
remote control. However, if you press the OUTPUT
button on the front panel first, you need to re-
Use when making settings while watching the
display on a TV screen.
48. ENTER Button
Press to accept a setting.
EN
–
–
10
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
53. SLOW Button [page 19]
49. g Button
During tape playback, press to view the video tape in
slow motion. Press again to resume normal playback.
This button does not affect DVD playback.
54. VCR/TV Button [page 21]
GDVD mode
Press to fast forward the Disc. Press the Pause but-
ton, then press the FWD button to begin slow
motion playback. Press the FWD button repeated-
ly to change the forward speed of slow motion.
GVCR mode
Use to select VCR or TV position. If the VCR/TV
light appears on the front of the DVD/VCR, it is in
VCR position (in either VCR or DVD mode). If the
VCR/TV light doesn’t appear on the front of the
DVD/VCR, it is in TV position.
Press to rapidly advance the tape, or view the pic-
ture rapidly in forward during playback (Forward
Search). When setting program (For example: set-
ting clock or timer program), press to determine
your selection and proceed to the next step you
want to input. Press to determine the setting
modes from the on screen menu. Press to add or
delete channel numbers during channel preset.
50. PLAY Button
GVCR Position
When the green VCR OUTPUT light appears on the
front of the DVD/VCR, use the VCR to watch a tape,
watch a TV program while recording it, or watch a
TV broadcast using the CHANNEL or the Number
buttons to change channels at the DVD/VCR.
When the green DVD OUTPUT light appears on
the front of the DVD/VCR, use the DVD/VCR to
view Disc playback or menus.
GDVD mode
Press to begin playback.
GVCR mode
GTV Position
Press to begin playback. Press to enter digits when
setting program (For example: setting clock or
timer program). Press to select the setting modes
from the on screen menu.
Use to watch TV (changing channels at the TV) or
watch one program while recording another.
55. SKIP/CH. Buttons
GDVD mode
51. VCR Button [page 13]
Press to skip Chapters or Tracks.
Press to select VCR mode for the remote control.
GYou can switch the OUTPUT mode either by
pressing the OUTPUT button on the front panel, or
by pressing the DVD or the VCR button on the
remote control. However, if you press the OUTPUT
button on the front panel first, you need to re-
select the corresponding mode by pressing the
DVD or the VCR button on the remote control.
52. PAUSE Button
GVCR mode
Press to change TV channels on the DVD/VCR.
56. AUDIO Button [page 31]
Press to select a desired audio language or sound mode.
Notes
GDVD mode [page 24]
Press to pause Disc playback. Press repeatedly to
advance the DVD picture step by step (or one
frame at a time).
¡To use the remote control to operate the DVD/VCR
and its features, press the DVD button on the remote
control before pressing other DVD buttons. Verify
that the green DVD OUTPUT Light is on.
¡To use the remote control to operate the VCR and its
features, press the VCR button on the remote control
before pressing other VCR buttons. Verify that the
green VCR OUTPUT Light is on.
GVCR mode [page 19]
While recording, press to temporarily stop the
recording (pause). Press a second time to resume
normal recording. You can not pause a One-Touch
Recording. Or, press during tape playback to
freeze the picture. Press to advance the picture one
frame at a time during still mode.
57
58 59
60
REAR VIEW
DVD/VCR
OUT
COMPONENT
VIDEO OUT
IN
ANT - IN
Y
L
AUDO
R
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
PCM / BITSTREAM
COAXIAL
S-VIDEO
OUT
L
Cb
Cr
ANT - OUT
R
VIDEO
CH3 CH4
67 65
66
64
62
63
61
57. AC Power Cord
58. AUDIO IN Jacks
Connect to a standard AC outlet to supply power
to the DVD/VCR.
Connect audio cables coming from the audio out
jacks of a camcorder, another VCR, or an audio
source here.
EN
–
–
11
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
59. DVD/VCR AUDIO OUT Jacks
Connect the supplied audio cables here and to the
Audio In jacks of a television or other audio
equipment.
64. VIDEO IN Jack
Connect a cable coming from the video out jack
of a camcorder, another VCR, or an audio-visual
source (laser disc player, video disc player, etc.)
here.
60. COMPONENT VIDEO OUT Jacks
Connect optional component video cables here
and to the component Video In jacks of a televi-
sion.
65. CH3/CH4 Switch
Set to channel 3 or 4 to use your TV with your
DVD/VCR.
61. COAXIAL Jack
66. ANT-IN (Antenna In) Jack
Connect your antenna, Cable Box, or Direct
Broadcast System.
Connect an optional coaxial digital audio cable
here and to the Coaxial Digital Audio In jack of a
decoder or audio receiver.
67. ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to connect this
jack to the ANTENNA IN Jack on your TV.
62. S-VIDEO OUT Jack
Connect an optional S-Video cable here and to
the S-Video In jack of a television.
63. DVD/VCR VIDEO OUT Jack
Connect the yellow video cable (supplied) here
and to the TV’s Video In jack.
Notes
¡The S-VIDEO OUT jack, COAXIAL jack, OPTI-
CAL jack, and COMPONENT VIDEO OUT jacks
are only useful in DVD mode.
DISPLAYS DURING
OPERATION
DISPLAY
Lit when the
A-B repeat function
is on.
Lights up when a DVD
is inserted into the tray.
Power on
Lit when the
repeat function is on.
No disc inserted
Tray open
Tray closed
Loading the Disc
Power off
Lights up when the
Lights up when a
inserted disc comes
CD is inserted on
to a pause.
the tray.
Lit when the inserted
disc is being played back.
Displays how long the current title
or track has been playing. When a
chapter or track is switched, the
number of the new title, chapter or
track is displayed.
LOADING THE BATTERIES
1. Open the battery compartment
cover.
2. Insert two AA batteries, with each
one oriented correctly.
3. Close the cover.
Notes
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
EN
–
–
12
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR/DVD SWITCHING
Since this product comprises VCR and DVD players, it is necessary to select the correct
output mode.
SWITCHING TO VCR MODE
SWITCHING TO DVD MODE
Press the VCR button on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
Press the DVD button on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
Notes
¡Pressing only the OUTPUT button on the front panel does not switch the mode of the remote control. You
always need to select the correct mode on the remote control too.
POWER
VIDEO
POWER SPEED AUDIO
DVD OPERATION
OUTPUT
VCR OPERATION
STOP/EJECT REW
CHANNEL
L
TIMER
SET
AUDIO
R
VCR/TV
CST.IN
OPEN/CLOSE
STOP
SKIP/REV PLAY
FWD/SKIP
PLAY
F.FWD REC/OTR
1
4
7
2
5
8
0
3
6
SKIP/CH.
VCR/TV
SLOW
9
+100
DVD OUTPUT Light
DVD button
VCR OUTPUT Light
+
10
DISPLAY DVD
VCR
PAUSE
VCR button
PLAY
VD OPERATION
OUTPUT
VCR OPERATIO
STOP
RECORD
MENU
ENTER
LAY
FWD/SKIP
STOP/EJECT REW
SETUP
TITLE
RETURN
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
OUTPUT button
SUBTITLE ANGLE REPEAT
A
B
EN
–
–
13
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
HOOKUPS
SETTING THE CH3/CH4
SWITCH
DVD/VCR TO TV CONNECTION
1. Disconnect the AC power cord of the TV from the If your TV does not have A/V terminals:
AC outlet.
When the DVD/VCR is in the VCR Playback mode or
when the DVD/VCR is in the VCR mode, your TV will
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of receive signals from the DVD/VCR on either channel
the DVD/VCR.
4. Connect the DVD/VCR to the TV using the coaxial the selector switch to CH3 or CH4 (which is located in
cable. the back of your DVD/VCR), whichever is not used for
3 or channel 4. To use the DVD/VCR with your TV, set
5. Plug the AC power cords of the DVD/VCR and TV normal broadcasts in your area. Then set your TV to
into the AC outlets.
the same channel.
[VHF/UHF
[Back of the DVD/VCR]
[Indoor antenna]
combination antenna]
[Back of the
ANT - IN
UHF/VHF combination TV]
Coaxial cable
(supplied)
OR
OR
ANT IN
-
ANT - OUT
CH4
CH3
CH3 CH4
UHF/VHF
[Cable box or satellite box]
ANT - OUT
CH3 CH4
IN
OUT
From Cable or
Satellite Company
[Back of the DVD/VCR]
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
CONNECTING TO A TV
DVD/VCR
COMPONENT
OUT
IN
VIDEO OUT
ANT - IN
Antenna/Cable signal
Y
L
AUDO
R
AUDIO OUT
DIGITAL AUDIO OUT
S-VIDEO
OUT
L
Cb
Cr
PCM
/
BITSTREAM
COAXIAL
ANT - OUT
A/V-compatible or
wide screen TV
R
VIDEO
CH3 CH4
To ANT. IN
of TV
[Fig. 1]
To VIDEO INPUT jack
To Right (red) and Left (white)
AUDIO INPUT jacks
To VIDEO OUT jack
AUDIO OUT jacks
Notes
¡Connect the DVD/VCR directly to a TV. If the A/V cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
CONNECTING TO A TV THAT HAS AN
S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-
tures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR. Therefore, in order to
use the VCR features or view TV channels on the DVD/VCR, you still need to either connect the RF coaxial cable
between the ANT-OUT jack of the DVD/VCR and the TV’s Antenna In jack, or connect the yellow video cable as
described earlier (Fig.1). To connect the supplied RF coaxial cable, see “DVD/VCR TO TV CONNECTION”
above.
DVD/VCR
COMPONENT
OUT
IN
VIDEO OUT
ANT - IN
Y
L
AUDO
R
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
PCM / BITSTREAM
COAXIAL
S-VIDEO
OUT
L
Cb
Cr
A/V-compatible or
wide screen TV
ANT - OUT
R
VIDEO
CH3 CH4
To Right (red) and Left (white)
AUDIO INPUT jacks
AUDIO OUT jacks
To S-VIDEO OUT jack
[Fig. 2]
To S-VIDEO INPUT jack
EN
–
–
14
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR TVs WITH
COMPONENT VIDEO IN JACKS
Use a component video cable (commercially available) in place of the yellow video cable to enjoy higher qual-
ity pictures.
The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR. Therefore, in
order to use the VCR features or view TV channels at the DVD/VCR, you still need to either connect the RF coax-
ial cable between the ANT-OUT jack of the DVD/VCR and the TV’s Antenna In jack, or connect the yellow video
cable as described earlier (Fig. 1). To connect the supplied RF coaxial cable, see “DVD/VCR TO TV CONNEC-
TION” on page 14.
To COMPONENT VIDEO
INPUT jacks
A/V-compatible
To COMPONENT VIDEO
OUT jacks
or
To Right (red) and Left (white)
AUDIO INPUT jacks
wide screen TV
To Right (red) and Left (white)
AUDIO OUTPUT jacks
DVD/VCR
OUT
COMPONENT
VIDEO OUT
IN
ANT - IN
Y
L
AUDO
R
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
SO
L
Cb
Cr
PCM
/
BITSTREAM
COAXIAL
ANT - OUT
CH3 CH4
R
VIDEO
[Fig. 3]
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL
INPUT JACKS SUCH AS MD DECK OR DAT DECK
Use an audio coaxial digital cables (not included) for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
DVD/VCR
COMPONENT
OUT
IN
VIDEO OUT
ANT - IN
Y
L
AUDO
R
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
PCM / BITSTREAM
COAXIAL
S-VIDEO
OUT
L
Cb
Cr
ANT - OUT
R
VIDEO
CH3 CH4
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
To COAXIAL DIGITAL
AUDIO OUT jack
[Fig. 4]
To COAXIAL DIGITAL
AUDIO INPUT jack
Notes
¡The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner’s Manuals for the components to be connected to the DVD/VCR.
¡Set Dolby Digital and DTS to off for audio output in the setup mode. Playing a DVD disc using incorrect set-
tings may generate noise distortion, and may also damage the speakers. (See page 36 to set Dolby Digital and
DTS to on)
EN
–
–
15
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A DOLBY DIGITAL DECODER OR DTS DECODER
If using this DVD/VCR to play a DVD disc in 5.1 channel Dolby Digital surround, or DTS surround formats,
the DVD/VCR outputs a Dolby Digital, or DTS data stream from its COAXIAL DIGITAL AUDIO OUT jack.
By hooking the DVD/VCR up to a Dolby Digital or DTS decoder, you can enjoy a more convincing, realistic
ambience with powerful and high-quality surround sound of a professional standard such as can be heard in
movie theaters.
Use an audio coaxial digital cables (not included) for the audio connections.
DVD/VCR
COMPONENT
OUT
IN
VIDEO OUT
ANT - IN
Y
L
AUDO
R
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
S-VIDEO
OUT
L
Cb
Cr
PCM
/
BITSTREAM
COAXIAL
ANT - OUT
R
VIDEO
CH3 CH4
Center speaker
To COAXIAL DIGITAL
AUDIO OUT jack
Front speaker
(right)
Front speaker
(left)
Dolby Digital,
DTS decoder
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
[Fig. 5]
Notes
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner’s Manuals for the components to be connected to the DVD/VCR.
¡If the output is Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio
output in the setup mode.
¡If the output is DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode.
¡Unless connected to a Dolby Digital decoder, or a DTS decoder, set Dolby Digital or DTS to off for audio out-
put in the setup mode. Playing a DVD using incorrect settings may generate noise distortion, and may also
damage the speakers.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems Inc.
CONNECTING TO AN ANALOG AUDIO
DVD/VCR
OUT
COMPONENT
VIDEO OUT
IN
ANT - IN
Y
L
AUDO
R
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
PCM / BITSTREAM
COAXIAL
S-VIDEO
OUT
L
Cb
Cr
ANT - OUT
CH3 CH4
R
VIDEO
Stereo system
To Right (red) and Left (white)
AUDIO OUT jacks
[Fig. 6]
To ANALOG AUDIO INPUT jacks
Notes
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR.
EN
–
–
16
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
AUTOMATIC CHANNEL SET UP
5 Begin channel preset by pressing the F.FWD
button once. The tuner scans and memorizes
all active channels in your area.
VCR
The DVD/VCR can automatically program the tuner to
scanonlythe channels which are available in your area.
¡The DVD/VCR distinguishes
CH 01
¡Channel memory programming is NOT needed
when the DVD/VCR is connected to a cable box or
a satellite box as in "DVD/VCR TO TV CONNEC-
TION" on page 14. In this case, set the CH3/CH4
Switch (which is located on the back of your VCR)
to either CH3 or CH4, whichever is not used for nor-
mal broadcasts in your area. Then set your TV to the
same channel. The channel you want to record or
view will be selected from the cable or the satellite
box.
between standard TV channels
and cable channels.
AUTO SET UP
6
After scanning, the tuner stops on the lowest
memorized channel.TheTV screen returns to
TV mode.
¡If “AUTO SET UP” appears on the TV screen again,
check the cable connections. Press the F.FWD but-
ton once again and the DVD/VCR will begin preset
again.
¡Follow the steps below once. Repeat only if there is
a power failure or if the DVD/VCR is unplugged for
more than 30 seconds. (In these cases, the pro-
grammed channels are erased.)
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using the
CHANNEL buttons (o/p) or by directly pressing the
Number buttons on the remote control.
¡You must follow the steps below before attempting to
play or record a video tape.
Note for using the Number buttons:
1
2
You need to connect the antenna or cable to
the DVD/VCR first. Then, connect the DVD
/VCR power plug to a standard AC outlet.
¡When selecting cable channels which are higher than
99, press [+100] first, then press the last two digits.
¡You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
Turn on the TV and set the TV to channel 3 or
4.
¡Now set the CH3/CH4 switch on the back of the
DVD/VCR to match the channel selected on the TV.
TO PRESET THE CHANNELS AGAIN
1
Press the MENU button until the main menu
appears. (If you have already set the clock,
you only have to press it once. If not, you
have to press it twice).
3
4
Turn on the DVD/VCR by pressing the
POWER button. Both the POWER and the
VCR/TV light will come on.
2
3
Select “CHANNEL SET UP” by pressing the
PLAY or the STOP button. Then, press the
F.FWD button.
Select the On Screen Language (“ENGLISH”,
“FRANCAIS” or “ESPAÑOL”) by pressing the
PLAY or the STOP button.
Then, press the F.FWD but-
ton.
Select “AUTO SET UP” by pressing the PLAY
or the STOP button. Then, press the F.FWD
button.
¡After scanning, the tuner stops on the lowest memo-
rized channel.
EN
–
–
17
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
TO ADD/DELETE CHANNELS
CLOCK SET UP
When scanning, some channels may be skipped due to
a weak signal. In such cases, you can add the channels
to the DVD/VCR memory manually.
VCR
Set the clock accurately for proper automatic timer
recording. We suggest that you use a TV or radio sta-
tion as your time source.
1
Press the MENU button until the main menu
appears. (If you have already set the clock,
you only have to press it once. If not you
1
Press the MENU button twice to call up the
main menu. (If you have already set the
clock, you only have to press it once).
have to press it twice).
- MENU -
TIMER PROGRAMMING
[OFF]
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
[ON]
TV STEREO
SAP
¡If the clock is not set, the CLOCK SET menu
appears first. In this case, follow step [3].
2
3
Select "CHANNEL SET UP" by pressing the
PLAY or the STOP button. Then, press the
F.FWD button.
2
3
Select "CLOCK SET" by pressing the PLAY
or the STOP button. Then, press the F.FWD
button
Select "MANUAL SET UP" by pressing the
PLAY or the STOP button. Then, press the
F.FWD button.
Set the clock.
1) Set the month
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
4
5
Enter the desired channel number by press-
ing the PLAY or the STOP button.
2) Set the day
Add or Delete it from memory by pressing the
F.FWD or the REW button so that "ADD" or
"DELETE" flashes on the TV screen accord-
ingly.
Press the PLAY button or STOP repeatedly.
Then, press the F.FWD button.
3) Set the year
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
The day of the week will appear automatically.
6
Exit the Preset mode by pressing the
CLEAR/C.RESET button.
4) Set the hour
TO CHANGE THE ON-SCREEN
LANGUAGE
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
VCR
5) Set the minute
1
2
3
Press the MENU button twice to call up the
main menu. (If you have already set the
clock, you only have to press it once).
Press the PLAY button or the STOP button repeatedly.
Then, press the F.FWD button.
Select "LANGUAGE SELECT" by pressing
the PLAY or the STOP button.Then, press the
F.FWD button.
6) Set AM or PM
CLOCK SET
MONTH DAY
YEAR
Press the PLAY button or the
STOP button repeatedly.
03 18 MON 2002
/
HOUR MINUTE AM/PM
05
:
40
PM AM
PM
Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing the PLAY or the
STOP button. Then, press the
¡To go back one step, press the REW button.
CLEAR/C.RESET button.
4
Start the clock by pressing the
CLEAR/C.RESET or the F.FWD button.
EN
–
–
18
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK FUNCTION
NORMAL PLAYBACK
2
Select "AUTO REPEAT" by pressing the
PLAY or the STOP button.
VCR
3
Begin auto repeat playback by pressing the
F.FWD button so that [ON] appears next to
"AUTO REPEAT".
1
Insert a prerecorded tape. The DVD/VCR will
turn on, and the VCR/TV Light
and the CST IN Light comes
on.
¡If the on-screen menu still remains, press the
CLEAR/C.RESET button to exit the menu.
¡If the safety tab has been removed, the DVD/VCR
will start playback automatically.
¡
To cancel the Auto repeat mode, press the F.FWD button at
step [3] so that [OFF] appears next to "AUTO REPEAT".
SEARCH FUNCTIONS
2
Turn on theTV and set theTV to channel 3 or 4.
¡Now set the CH3/CH4 switch on the back of the
VCR
DVD/VCR to match the channel selected on the TV.
PICTURE SEARCH
3 Begin playback by pressing the PLAY button.
If you want to skip or repeat a scene during playback,
press the F.FWD or the REW button.
¡Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press the CHAN-
NEL buttons (o/p) on the DVD/VCR.
¡Press it again and the DVD/VCR will now search at
super high speed. (in the LP/SLP modes only).
INDEX SEARCH
The index signal is recorded on the tape automatically
when the recording is started. If you want to view a
recording at a specific start point, this can be done easily.
¡When a tape has reached the end, the DVD/VCR
will automatically rewind the tape to the beginning,
and eject the tape.
1
Press the SEARCH MODE button so that the
Index Search menu appears.
¡S-VHS Quasi Playback (SQPB): This unit allows
you to view a tape recorded in S-VHS format.
(Noise lines may appear on the picture.)
2
Enter your desired number by pressing the
PLAY or the STOP button
INDEX SEARCH
03
4
To stop playback, press the STOP button.
within 30 seconds.
PAUSE/STILL/SLOW
You can freeze the picture on TV screen by pressing
the PAUSE button during playback.
¡You can advance the picture by one frame at a time
by pressing the PAUSE button during the Still mode.
¡If the picture begins to vibrate vertically during the
still mode, stabilize the picture by pressing the
CHANNEL buttons (o/p).
¡If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if so
equipped.You can watch in the slow motion by
pressing the SLOW button during playback or the
still mode.
¡If a noise bar appears on the TV screen, you can
reduce it by pressing the CHANNEL buttons (o/p).
¡After the DVD/VCR has been in Still/Slow mode for
5 minutes, it will stop automatically to protect the
tape and the video head from damage.
3
Press the F.FWD or the REW button to start
index search.
¡If you want to go in the forward direction, press the
F.FWD button. If you want to go in the reverse
direction, press the REW button.
¡After index search, the DVD/VCR will play the tape
automatically.
TIME SEARCH
This feature allows you to fast forward or rewind the
tape for the desired length of time.
1
Press the SEARCH MODE button twice so
that the Time Search menu appears.
2
Enter your desired time to
skip by pressing the PLAY
TIME SEARCH
2 : 50
or the STOP button within
30 seconds.
¡To return to playback, press the PLAY button.
3
Press the F.FWD or the REW button to start
time search.
AUTO REPEAT PLAYBACK
VCR
¡
If you want to go in the forward direction, press the
F.FWD button.
¡If you want to go in the reverse direction, press the
REW button.
This feature allows you to play a tape over and over.
¡After time search, the DVD/VCR will play the tape
automatically.
1
Select main menu by pressing the MENU
button.
EN
–
–
19
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING FUNCTION
VCR VCR
It may be UNLAWFUL to record copyrighted materi-
¡
¡
If a tape ends during OTR, the VCR will stop, eject the
al without the consent of the copyright owner.
Accidental Erasure Prevention
tape, and switch to the DVD mode automatically as the
TIMER SET light blinks. (If the DVD power is off, the
DVD/VCR will become STANDBY status).
To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover the
When OTR is finished , the VCR turns off automatically.
To use the VCR again, press the TIMER SET button on
the DVD/VCR.
Record safety tab
hole with cellophane tape.
Before recording, make sure:
¡The desired channel is selected by pressing the
Number buttons on the remote control or the
CHANNEL buttons (o/p). (If you connected the
DVD/VCR to a cable box or satellite box as in
"DVD/VCR TO TV CONNECTION" on page 14,
set the DVD/VCR to channel 3 or 4 i.e. the same
channel as the CH3 or CH4 switch on the back of
the DVD/VCR. Then, select the channel you want
to record with the cable box or satellite box. In this
case, you can ONLY record and view the SAME
channel.)
TIMER RECORDING
VCR
You may set the DVD/VCR to start recording while
you are away. You can set seven programs to record on
specific days, daily or weekly within a 1 year period.
If you have not yet set the clock, "CLOCK SET"
appears. If so, follow the steps [3] and [4] in
"CLOCK SET" section on page 18. Then, set the
timer recording.
¡There is a tape with a safety tab into the DVD/VCR.
¡The desired recording speed is selected in SP (stan-
dard play) or SLP (super long play) mode by press-
ing the SPEED button on the remote control.
1
2
3
Insert a tape with its safety tab intact.
Press the MENU button.
Select "TIMER PROGRAMMING" by pressing the
Tape Speed
Recording/Playback Time
PLAY or the STOP button. Then,
Type of tape
SP mode
SLP mode
T60
1 hour
3 hours
T120
2 hours
6 hours
T160
2-2/3 hours
8 hours
TIMER PROGRAMMING
PROGRAM NMBER 1 2 3 4 5 6 7
press the F.FWD button. The set
DATE
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
- - / - -
up screen is displayed.
¡TV STEREO or SAP is selected.
VIEWING AND RECORDING
THE SAME PROGRAM
4
Set the timer.
¡If you make mistakes, press the REW button repeat-
edly to go back to the item you want to correct.
VCR
¡If you press the REW button after step ), all the
7
information you’ve just entered for that program
1
Begin the recording by pressing the RECORD
button. The REC/OTR Light comes on.
number will be cleared.
¡
¡
To temporarily stop recording or to resume it, press the
PAUSE button. After the DVD/VCR has been in Pause
mode for 5 minutes, it will stop automatically to protect
the tape and the video head from damage.
1) Set the program number (1-7)
PROGRAM NUMBER
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
4
A program number which is not allocated
flashes. Press the PLAY button or the
STOP button repeatedly for the desired
2
Press the STOP button when the recording is
completed.
program number. Then, press the F.FWD button.
If a tape ends during recording, the VCR will automati-
cally stop, rewind, and eject the tape.
2) Set the frequency of the recording
OTR (One Touch Recording)
Press the PLAY button or the STOP
PROGRAM NUMBER
4
button to select the desired frequency from
ONCE, DAILY, or WEEKLY recording.
Then, press the F.FWD button
ONCE
DAILY
WEEKLY
VCR
This feature allows you to set the recording length simply by
pressing the REC/OTR button on the DVD/VCR.
ONE TIME PROGRAM
PROGRAM NMBER 4
3) Set the date
3
Press the REC/OTR button to begin OTR. The
REC/OTR Light comes on. Change the recording
length by pressing the REC/OTR button repeatedly.
DATE
- - / - - - -
START TIME
- - : - - - -
First, press the PLAY button or the STOP
button for the month. Then, press the F.FWD
button. Next, press the PLAY button or the
END
TIME
- - : - - - -
CHANNEL
- -
REC SPEED
- -
- -
- - -
REC
OTR(0:30)
OTR(1:00).....
STOP button for the day. Then, press the F.FWD button.
(Normal recording)
OTR(8:00)
OTR(7:30)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
–
–
20
1L25
¡
¡
If a tape is not in the DVD/VCR or does not have a safety
tab, the TIMER SET light flashes and timer recording
will not operate. Please insert a recordable tape.
ONE TIME PROGRAM
PROGRAM NMBER 4
4) Set the start time
DATE
05 /13 MON
START TIME
- - : - - - -
First, press the PLAY button or the STOP
button for the hour. Then, press the
F.FWD button. Next, press the PLAY
END
TIME
- - : - - - -
CHANNEL
- -
When all timer recordings are finished, the TIMER
SET light will flash. To use the DVD/VCR again as
usual, press the TIMER SET button to disable the
flashing TIMER SET light, then press the VCR/TV
button to select the VCR position. The VCR/TV light
will appear. Press the VCR button to choose VCR or
DVD mode, then continue with the other features as
described in this manual.
When timer recordings are set, the TIMER SET light
will come on. To use the DVD/VCR as usual until the
time for the recording, press the TIMER SET button
so that the TIMER SET light disappears. Press the
VCR/TV button to choose the VCR position. The
VCR/TV light will come on. Press the VCR button to
choose VCR or DVD modes, then continue with the
other features as described in this manual.
REC SPEED
- -
- -
- - -
button or the STOP button for the minute. Then, press the
F.FWD button. And then, press the PLAY button or the
STOP button for AM or PM. Then, press the F.FWD button.
ONE TIME PROGRAM
PROGRAM NMBER 4
5) Set the end time
DATE
05 /13 MON
¡
START TIME
07: 30 PM
Follow the same instructions as
"Set the start time" to set
the end time.
END
TIME
- - : - - - -
CHANNEL
- -
REC SPEED
- -
- -
- - -
ONE TIME PROGRAM
PROGRAM NMBER 4
6) Set the channel number
DATE
05 /13 MON
START TIME
07: 30 PM
Press the PLAY button or the STOP
button repeatedly for the desired channel
number. Then, press the F.FWD button.
END
TIME
08: 30 PM
CHANNEL
- -
REC SPEED
- -
- -
- - -
If you want to use the DVD player during
a VCR timer recording or while the TIMER
SET light is on or flashes.
If you connected the DVD/VCR to a cable box or satellite box
as in "DVD/VCR TO TV CONNECTION" on page 14, set the
DVD/VCR to channel 3 or 4 i.e. the same channel as the CH3
or CH4 switch on the back of the DVD/VCR. Then, select the
channel you want to record with the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
¡
You can use the DVD player while the TIMER SET
light is on or flashes, or during a timer recording. Press
the POWER button to turn on the DVD/VCR. Press
the VCR/TV button to choose VCR position. Press the
DVD button on the remote control to choose DVD
mode, then continue with the other DVD features as
described in this manual. You don’t have to set the
TIMER off to use the DVD.
ONE TIME PROGRAM
PROGRAM NMBER 4
7) Set the tape speed
DATE
05 /13 MON
07: 30 PM
08: 30 PM
16
START TIME
Press the PLAY button or the STOP
button repeatedly for the desired tape
speed. Then, press the F.FWD button.
END
TIME
CHANNEL
REC SPEED
SP
SP
SLP
TO STOP AN AUTOMATIC TIMER PRO-
GRAM ALREADY STARTED
Press the STOP/EJECT or the TIMER SET button on
the DVD /VCR.
5
To set another program, repeat step [4]. To exit
from the set up screen, press the
CLEAR/C.RESET button (You only exit from the
set up screen. the information you entered for
the timer recording will not be cleared).
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
6
When you finish programming, press the
TIMER SET button to activate the timer.
¡As the TIMER SET light comes on the VCR
becomes STANDBY status, and switches to DVD
OUTPUT mode automatically.
1
Turn the power on by pressing the POWER
button. (If the DVD/VCR is in TIMER STAND-
BY status, press the TIMER SET button
instead of the POWER button.)
¡When DVD sits idle for more than thirty-five min-
utes, the DVD power will be turned off automatical-
ly. If you press the TIMER SET button under such
condition, the DVD/VCR power will be turned off
and become STANDBY status.
2
3
Select main menu by pressing the MENU
button.
Select "TIMER PROGRAMMING" by press-
ing the PLAY or the STOP button. Then,
press the F.FWD button.
TO CLEAR A PROGRAM
Follow the steps from 2 to 3. Select the program num-
ber you want to clear, and then press the REW button.
4
Select the program number which you want
to check by pressing the PLAY or the STOP
button.
HINTS FOR TIMER
RECORDING
¡The details of the selected program appears on the
TV screen.
VCR
¡Go to the digit you want to change by pressing the
F.FWD or the REW button. Then, enter correct num-
bers by pressing the PLAY or the STOP button.
¡You may cancel the entire program by pressing the
REW button while the program number flashes.
¡If there is a power failure or the DVD/VCR is
unplugged for more than 30 seconds, the clock set-
ting and all timer settings will be lost.
¡If a tape ends during TIMER RECORDING, the
VCR will stop, eject the tape, and switch to the DVD
mode automatically as the TIMER SET light blinks.
(If the DVD power is off, the DVD/VCR will
become STANDBY status).
5
6
Press the CLEAR/C.RESET button to exit.
Press the TIMER SET button to return to
timer stand-by mode.
EN
–
–
21
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
¡Always use video-quality shielded cables with
RCA-type connectors. Standard audio cables are not
recommended.
¡You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in
place of the playing VCR.
COPYING A VIDEO TAPE
VCR
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording DVD/VCR (this unit), the play-
ing VCR (another source) and your TV using the fol-
lowing diagram.
TO MONITOR THE RECORDING
1
Turn on theTV and set theTV to channel 3 or 4.
¡Now set the CH3/CH4 switch on the back of the
DVD /VCR to match the channel selected on the TV.
¡You can use the AUDIO/VIDEO input jacks on the
front panel of the DVD/VCR instead of using the
jacks on the back.
2
Press the VCR/TV button on the recording
VCR so that the VCR/TV Light comes on.
[Recording VCR]
(this unit)
MTS (Multi-Channel Television
Sound) SYSTEM
DVD/VCR
OUT
COMPONENT
IN
VIDEO OUT
ANT - IN
Y
L
AUDO
R
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
S-VIDEO
OUT
L
VCR
Cr
PCM BITSTREAM
/
COAXIAL
ANT - OUT
R
VIDEO
Cb
3CH 4CH
When you play a VHS tape, or receive a broadcast on the
DVD/VCR tuner channel you are watching, the current
status will appear when you press
Coaxial cable
Audio/Video cables
(not supplied)
(supplied)
STOP
12:00AM
CH 32
STEREO
SAP
the DISPLAY button on the
remote control. When you record a
MTS broadcast signal, you need to
set it to MTS mode.
[TV set]
(Use for monitoring)
1)*
OUT
LEFT RIGHT
SP
0:00:00
HIFI
IN
2)*
AUDIO
VIDEO
[Playing VCR]
(another source)
1)* When a program is broadcast in stereo,
ANT in
STEREO appears. When a program is
broadcast in second audio, SAP appears.
Although a program may be broadcast in both stereo
and sub audio, you must select the Recording mode to
TV STEREO or SAP before you record a broadcast.
1
2
3
Insert a pre-recorded tape into the playing
VCR.
¡
Insert a tape with a safety tab into the
recording VCR.
2)* While the VCR is set in HiFi stereo mode,
HiFi appears on the TV screen. While the
VCR is set in monaural (MONO) mode,
HiFi disappears from the TV screen.
Press the SPEED button on the recording
VCR to select the desired recording speed
(SP/SLP).
¡If you play non-HiFi tapes while the VCR is set in
HiFi, HiFi will disappear from the TV screen and the
VCR will automatically play in monaural.
¡
When you use the A/V input jacks on the back of the
DVD/VCR, select "L1" position by pressing [0], [0], [1]
on the remote control or the CHANNEL buttons (o/p).
¡
When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0], [2]
on the remote control or the CHANNEL buttons (o/p).
MTS RECORDING/MONITOR MODE
Display on the
TV screen
Type of
STEREO/SAP
Selection
Hi-Fi audio track
(2-channel)
Normal audio
track
broadcast
L-channel R-channel
Regular
-None-
-Invalid-
Note
(monaural audio)
Mono
L
Mono
R
Mono
L+R
“L1” and “L2” are found before the lowest memo-
rized channel. (Example: CH2)
Stereo
broadcast
STEREO
SAP
-Invalid-
TV STEREO*
SAP*
Main audio Main audio Main audio
program
program
program
Bilingual
broadcast
Sub audio Sub audio
Sub audio
program
4
5
Press the REC/OTR button on the recording VCR.
program
L
program
R
TV STEREO*
SAP*
L+R
Sub audio
program
Stereo &
Bilingual
broadcast
STEREO
SAP
Begin playback of the tape in the playing
VCR.
Sub audio Sub audio
program program
*
¡For best results during dubbing, use the
DVD/VCR’s front panel controls whenever possi-
ble. The remote control might affect the playing
DVD/VCR’s operation.
EN
–
–
22
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO REWIND
REAL TIME TAPE COUNTER
When a tape reaches the end during recording, play-
back, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
DVD/VCR will eject the tape and switch itself off.
¡The DVD/VCR will not rewind the tape automati-
cally during timer recording or One Touch
Recording.
¡This shows the elapsed recording or playback time
in hours, minutes, and seconds. (The displayed time
will not change during blank portions of the tape.)
¡The indication will appear when the tape is rewound
further than “0:00:00” on the tape counter.
PLAYING A DISC
Notes
PLAYING A DVD VIDEO
OR AN AUDIO CD
¡A “prohibited icon” may appear at
the top-right on the TV screen
during operation, warning that a
prohibited operation has been
encountered by the DVD/VCR or
the disc.
DVD
CD
Getting started
Turn on the power of the TV, amplifier and any other
components which are connected to the DVD/VCR.
(Change the input system to suite the DVD/VCR, and
check that the sound volume is correct).
¡If a disc is dirty or has scratches, the pictures may
appear distorted and the playback operation may
stop. In such cases, clean the disc and unplug the
power cord and then plug it again before resuming
playback.
1
Press the POWER button.
¡The power will turn on.
¡With DVDs that use titles for playback program
signals, playback may start from the second title, or
it may skip these titles.
Check that the DVD OUTPUT Light is lit. If not
press the DVD button on the remote control to
switch to DVD/VCR mode.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
2
Press the OPEN/CLOSE button.
¡The disc loading tray will open.
3
Place a disc into the tray.
USING THE DVD MENUS
¡Make sure the disc is sitting properly in the correct
recess, with the label side up.
DVD
Some DVDs contain their own menus, such as a guid-
ance menu which describes the contents of the disc or
a selection menu for sound, language and other cus-
tomized settings.
1
Press the MENU button.
4
Press the PLAY button.
¡The DVD menu will appear.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
You need to press the PLAY button only when the
tray has been closed by pressing the OPEN/CLOSE
button.
2
Select the desired title.
¡Press the Arrow buttons (L/K/B/s) to change the
setting, and then press the ENTER button.
¡If your DVD has a title menu, it may appear on the
screen. In this case, refer to “USING THE DVD
MENUS” in the next section, or “USING THE
TITLE MENU” on page 24.
3
Playback will start from the selected title.
5
Press the STOP button to stop play.
EN
–
–
23
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
RESUMING PLAYBACK FROM
THE POINT WHERE
USING THE TITLE MENU
PLAYBACK STOPPED
DVD
DVD
CD
With a DVD containing a title menu, you can select the
desired titles from the menu.
1
Press the STOP button during playback.
1
Press the TITLE button.
¡Playback will stop, and then appear the resuming
message at the center.
¡The title menu will appear.
¡With some discs, a title menu may appear automati-
cally. In this case, skip to step 2.
Press 'PLAY' to play from here.
To play the beginning, press 'STOP' first
and then 'PLAY'.
2
Select the desired title.
¡Press the Arrow buttons (L/K/B/s) to select a
desired title, and then press the ENTER button.
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVDs
2
Press the PLAY button. Playback will start
from the point where the previous playback
session was stopped.
B
¡Press the MENU button to call up the DVD menu.
¡Press the TITLE button to call up the title menu.
Note
Note
¡The contents of menus and corresponding menu
operations may vary between discs. Refer to the
manual accompanying the disc for details.
¡The resume function can be reset by pressing the
STOP button twice or by opening the disc loading
tray.
PAUSING PLAYBACK OR
DISPLAYING A STILL PICTURE
STEPPING THROUGH FRAMES
DVD
CD
DVD
1
Press the PAUSE button during playback.
1
Press the PAUSE button while playback is
¡Playback will pause, with sound
muted.
F
paused.
F
¡The next picture frame is dis-
played with sound muted each
time the button is pressed.
2
Press the PLAY button to resume playback.
2
Press the PLAY button to resume playback.
B
B
EN
–
–
24
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING FROM A DESIRED
TRACK
FAST FORWARD/REVERSE
DVD
CD
CD
1
Press the FWD g or the REV h button
during playback.
1
Press the Number buttons to enter the
desired track number.
¡For DVDs, pressing the FWD g or REV h but-
ton cycles the playback speed in four steps. In the
case of DVDs, the sound will mute.
¡For audio CDs, the playback speed is fixed at ×16.
¡
The selected track will be located, and playback will start.
You can also press the SEARCH
MODE button and use the Number
buttons to enter the track number.
:
TR
5
REV
Button
FWD
Button
x2
x8
x2
x8
When the track number is entered in the entry box,
playback of the desired track will start automatically.
TRICKS WITH THE SKIP BUTTONS (H, G)
If the SKIP button G is pressed during playback
or while playback is paused, the current track will
be skipped and the next track will start. If the SKIP
button H is pressed once, the beginning of the
current track will be located for replay. If the SKIP
button H is pressed again within 2 seconds
after playback begins, the previous track will be
located.
x30
x60
x30
x60
PLAYING FROM A DESIRED
TITLE OR A CHAPTER
2
1
Press the PLAY button to return to normal
playback speed.
DVD
There are two ways you can jump to a desired title or
a chapter.
SLOW MOTION
DVD
By using the ‘SEARCH MODE’ button.
Press the FWD g button while playback is
paused. (Sound remains muted.)
1
Press the ‘SEARCH MODE’ button.
¡The title/chapter search display will be displayed.
¡Slow motion mode will be activated.
TT : 1/ 2
TT : _/ 12
¡Pressing the FWD g button cycles the playback
speed in three steps. Select the appropriate speed
while referring to the speed indication on the screen.
CH __ / 49
CH : 12/ 49
FWD
Button
2
3
If you wish to perform a title search, select
‘TT’. If you wish to perform a chapter search,
select ‘CH’ with the Arrow buttons (K/L).
×1/16
Enter the desired title or chapter number
with the Number buttons (If you are entering
a single digit number press “0” first).
×1/8
¡When you finish entering the number, the selected
title or chapter will start automatically
Notes
×1/2
.
¡If you didn’t press “0” before entering the single
digit number, you have to press ENTER to go to the
desired title or the chapter.
2
Press the PLAY button to return to normal
playback speed.
Notes
¡Slow playback is not available with audio CDs.
¡Reverse slow motion is not available.
¡Slow playback from a TITLE to other TITLE is not
possible.
EN
–
–
25
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
By using only the Number buttons.
TITLE SEARCH:
MARKER
1
Directly enter the desired title number with the
Number buttons with playback stopped.
DVD
CD
CHAPTER SEARCH:
You can define the part to be called back.
1
Directly enter the desired chapter number
with the Number buttons when the disc is
being played or paused.
1
Press the SEARCH MODE button three
times during playback.
¡When you finish entering the number, the selected
1 2 3 4 5 AC
NOT SET
title or chapter will start automatically.
Set the marker
¡Using the Arrow buttons (s/ B),
position the cursor on to the
marker number shown as “NOT SET”. Press the
ENTER button when the screen to be reviewed
appears. The marked time will be displayed. Up to
5 points can be marked.
Notes
¡Play back from a desired title or chapter is not avail-
able with some DVDs.
¡If the title being played does not display the chapter
number, that means the chapter search function is
not available with that title.
TRICKS WITH THE SKIP BUTTONS (H, G)
Call back the marker
¡Using the Arrow buttons (s/B), position the cursor
on to the marker number to be called back and press
the ENTER button.
If the SKIP button G is pressed during playback or
while playback is paused, the current chapter will be
skipped and the next chapter will start. If the SKIP
button H is pressed once, the beginning of the cur-
rent chapter will be located for replay. If the SKIP
button H is pressed again within 2 seconds after
playback begins, the previous chapter will be locat-
ed.
Clear the marker
¡Using the Arrow buttons (s/B), position the cursor
on to the marker number to be cleared and press the
CLEAR/C.RESET button.
To clear all markers, place the cursor on “AC” (All
clear markers) and press the ENTER button.
STARTING FROM A DESIRED
TIME COUNT
2
Press the SEARCH MODE button or the
RETURN button to exit the display.
DVD
CD
RANDOM (Audio CD)
1
2
Press the SEARCH MODE button twice dur-
ing playback or while paused.
CD
1
Press the MODE button in stop mode.
Press the Number buttons to set the desired
¡The program setting menu screen will appear.
time count.
TIME 1:23:30
TOTAL 1:29:00
¡Example: 1 hour, 23 minutes and
30 seconds
2
Press the MODE button again.
1 → 2 → 3 → 3 → 0
RANDOM
Notes
¡For a DVD, Time Search in Title is effective. (But
Time Search in Chapter is ineffective.)
START : PLAY
EXIT : MODE
¡For a CD, Time Search in Track is effective. (But
Time Search in the entire disc is ineffective.)
¡Playback from a desired time count is not available
with some discs or if the unit is in stop mode.
¡If the wrong numbers are entered, press the
CLEAR/C.RESET button and re-enter the correct
numbers.
3
Press the PLAY button. Random playback
will then start.
Note
¡Program playback is not available during random
playback.
EN
–
–
26
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
REPEAT
A-B REPEAT
DVD
CD
DVD
CD
1
Press the REPEAT button during playback.
You can define a section to be played back repeatedly.
For DVDs
1
Press the A-B REPEAT button during playback.
¡A single title or chapter can be played back repeat-
edly.
REPEAT
¡The starting point (A) will then be
selected.
[ A -
]
¡Pressing the REPEAT button cycles the display on
the screen as follows.
REPEAT
[OFF]
No repeat playback.
2
Press the A-B REPEAT button again at the
end point (B) of the desired section.
REPEAT
[CHAPTER]
The current chapter is
¡The selected section will be
played back repeatedly.
played back repeatedly.
REPEAT
[ A - B ]
REPEAT
[TITLE]
The current title is
played back repeatedly.
3
To exit A-B repeat playback, press the A-B
For audio CDs
REPEAT button and set it to OFF.
REPEAT
[ OFF ]
¡The whole disc or a single track can be played back
repeatedly.
¡Pressing the REPEAT button cycles the display on
the screen through Off, Track and All.
Notes
¡With DVDs, the A-B repeat section can be set only
within the current title.
REPEAT
[OFF]
No repeat playback.
¡With audio CDs, the A-B repeat section can be set
within the current track.
REPEAT
[TRACK]
The current track is
played back repeatedly.
¡A-B repeat is not available with some scenes in
DVD.
REPEAT
[ALL]
The whole disc is
played back repeatedly.
¡To cancel the A point which was set, press the
CLEAR/C.RESET button.
¡A-B repeat playback does not function when title,
chapter, or repeat (all) playback has been set.
If the REPEAT button is pressed once dur-
ing program/random playback, the current
track will be played back repeatedly.
If the REPEAT button is pressed again, the
program/random playback will be per-
formed repeatedly.
Notes
¡Repeat playback is not available with some discs.
¡The REPEAT setting will be cleared when moving
to an other title, chapter or track.
¡Repeat playback does not function during A-B
repeat playback.
EN
–
–
27
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
ZOOM PLAYBACK
PROGRAM (Audio CD)
(enlargement on-screen)
CD
DVD
Images can be enlarged on the screen to your taste.
1
Press the MODE button in stop mode.
¡The program screen will appear.
1
Press the ZOOM button during playback.
PROGRAM
--
TIME 0:00:00 1/1
¡The image will be enlarged at the center of the
screen.
¡Pressing the ZOOM button cycles the zooming
START: PLAY
DELETE
EXIT
:
CLEAR
RETURN
RANDOM
:
MODE
:
images in two steps.
2
Press the Number buttons to enter the
desired track numbers.
ZOOM [x2]
ZOOM [x4]
ZOOM [OFF]
PROGRAM
TIME 2:07:43 1/1
02 05 07 04 10 14 06 15 21 08
20 28 10 25 35 12 30 42 11 34
¡50 programs can be displayed
at once on the screen. Press
“L” to go to the next page.
49 16 40 58 18 45 63 01 03
_
START: PLAY
RANDOM MODE
DELETE
EXIT
:
CLEAR
RETURN
:
:
2
When the Arrow button (K/L/s / B) is
pressed during zoom play, the part to be
zoomed moves.
3
Press the PLAY button.
¡The zooming frame can be moved from the center 4
steps to the right, 4 steps to the left, 4 steps to the
top, and 4 steps to the bottom when times 2 zoom-
ing. The frames will move 6 steps when times 4
zooming.
¡Playback will start in the programmed order.
¡While the program is being played back, the STOP
button works as follows.
¡Press the STOP button once and then press the
PLAY button again. Playback will restart from the
point where the STOP button was pressed. (Program
continued)
¡The current position will be displayed on the right-
bottom of the screen. Press the ENTER button, and
the display will disappear.
TO CLEAR THE PROGRAM
1
Press the STOP button twice, and the pro-
gram will be cleared.
Notes
¡Adding programs is not possible during program
playback. You must stop the current playback before
such operations can be carried out.
¡Press the CLEAR/C.RESET button to cancel a pro-
gram. The most recently entered program will then
be deleted.
Note
¡Zooming function does not work while the disc
menu is being shown.
¡Up to 99 programs can be entered.
¡Playback from a desired track and random playback
are not available during program playback.
¡Program settings will be cleared when the power is
turned off or the disc loading tray is opened.
¡Press the MODE button to check the programmed
setting.
¡The programs will be cleared when you turn the
power off.
EN
–
–
28
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE ON-SCREEN
DISPLAY DURING MP3 DISC PLAY
PLAYING AN MP3 DISC
MP3
MP3
The information on an MP3 disc in play can be
checked.
1
Insert an MP3 file recorded on disc.
¡The MP3 menu screen is displayed.
1
Press the DISPLAY button during playback.
¡Folders are referred to as
“Albums” and files are
referred to as “Tracks”.
VOLUME LABEL
¡The track currently being
played will be highlighted.
ALBUM NAME
A
FIRST PLAY
+ALBUM01
+ALBUM02
+ALBUM03
+ALBUM04
TRACK11
TRACK12
TRACK13
TRACK14
TRACK15
1/15
¡“+” appears at the beginning
SELECT:
RETURN:
/
ENTER:
START
of the album name.
:
PLAY
¡If all the tracks cannot be displayed at once on the
screen, “L” appears to go to the next page. If there
is a previous page, “K” appears on screen. To the
left of “L”, the current page and the total number of
pages are displayed.
2
Press the DISPLAY button again.
¡The album name being displayed will be replaced by
the elapsed time of the track.
¡
will be displayed when repeat play has been
¡The player can recognize 255 albums and tracks
altogether.
selected.
0:02:31
A
T: Track repeat
TRACK11
TRACK12
TRACK13
TRACK14
TRACK15
2
Using the Arrow buttons (K/L), select a
album or a track to be played.
A: Album (folder) repeat
D: Disc repeat
[When a TRACK is selected]
Starting from the selected track,
the rest of the tracks will be
played in order.
ALBUM01
+ALBUM11
+ALBUM12
+ALBUM13
+ALBUM14
+ALBUM15
3
Press the DISPLAY button again, and the dis-
play screen disappears.
SELECT:
RETURN:
/
ENTER:
START
:
PLAY
[When an ALBUM is selected]
Press the Arrow button (B). The track selection screen
shows up. Using the Arrow buttons (K/L), select the
tracks to be played.
¡Choose “FIRST PLAY”, and the albums and tracks
will be played from the beginning of the disc.
¡Press the TITLE button, and the top hierarchy will
be called back.
¡Albums can be played up to the 8th hierarchy.
3
Press the PLAY button.
¡Playback will start.
To stop playing, press the STOP button.
4
EN
–
–
29
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A DESIRED TRACK
FROM AN MP3 DISC
PLAYING AN MP3 DISC IN A
PROGRAM
MP3
MP3
1
P
back.
ress the SEARCH MODE button during play-
1
Press the MODE button in STOP mode.
¡The program screen is displayed.
¡The SEARCH menu is displayed.
PROGRAM-FOLDER NAME
¡The track currently being played or in RESUME ON
will be highlighted. In the case of RESUME OFF,
the first track of the disc will be highlighted.
+ALBUM01
+ALBUM02
+ALBUM03
TRACK01
TRACK02
1/11
1/1
¡Press the RETURN button, and the SEARCH menu
disappears.
START
RANDOM: MODE
:
PLAY
DELETE: CLEAR
EXIT RETURN
:
ALBUM NAME
+ALBUM01
TRACK11
TRACK12
TRACK13
2
Use the Arrow buttons (L/K) to select a
track. Then press the ENTER button to save
it in a program.
TRACK14
1/15
SELECT:
RETURN:
ENTER:
START PLAY
:
PROGRAM - ALBUM01
+ALBUM11
+ALBUM12
TRACK11
TRACK12
TRACK13
TRACK11
2
Using the Arrow buttons (K/L), select the
track to be played. Then press the PLAY but-
ton to start playing.
1/11
1/1
START
:
PLAY
DELETE: CLEAR
RANDOM: MODE
EXIT:
RETURN
Notes
¡When an album name is highlighted, press the
Arrow button (L), and the next hierarchy is dis-
played.
¡During play, a desired track can be searched for
directly. Just enter the track number with the
Number buttons.
¡Press the Arrow button (K) to go back to the previ-
ous hierarchy.
¡If the track number entered is not available, the “dis-
able” symbol appears and the direct search mode is
cancelled.
¡If the entire program cannot be displayed at once on
the screen, “L” appears to go to the next page.
¡Playback cannot be started from a desired time
count.
3
When the program has been selected, press
the PLAY button.
¡The program will begin.
PLAYING AN MP3 DISC
RANDOMLY
Notes
MP3
¡Press the CLEAR/C.RESET button, and the last-
programmed entry will be deleted.
1
Press the MODE button twice in STOP mode.
¡Press the RETURN button, and the program screen
will be displayed and the program stored in memo-
ry.
¡The random setting menu screen will appear.
RANDOM
¡The program setting will be cancelled when the
power is turned off or the disc tray is opened.
PROGRAM - ALBUM05
+ALBUM51
+ALBUM52
TRACK51
TRACK52
TRACK63
TRACK11
TRACK52
TRACK31
TRACK22
TRACK03
START
:
PLAY
EXIT: MODE
1/11
2/3
START
RANDOM: MODE
:
PLAY
DELETE:
EXIT
CLEAR
RETURN
:
2
Press the PLAY button.
¡Random play will begin.
EN
–
–
30
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTINGS
Notes
CHANGING THE AUDIO
LANGUAGE OR SOUND MODE
¡Pressing the Audio button may not work on some
DVDs with multiple audio languages (e.g. DVDs
which allow audio language setting on the disc
menu). Operation varies between discs, so refer to
the manual accompanying the disc.
DVD
CD
The DVD/VCR has a function which allows you to
select the desired audio language and sound mode.
¡The current audio language and sound mode will be
displayed when you first press the AUDIO button.
For DVDs
¡If the desired language is not shown after pressing
the Audio button several times, the disc does not
have an audio source in that language.
1
Press the AUDIO button during playback.
¡The current audio status will appear at the top.
¡The audio language resets to the one which was
selected in the setup mode every time the power is
turned on or discs are replaced. If that language is
not available on a disc, a language defined by the
disc will be selected.
2
Press the AUDIO button repeatedly until you
see the language of your choice.
¡The audio language mode can be changed only if the
disc is recorded with a multiple language setting.
¡The screen display will disappear after about 5
seconds.
AUDIO 1.ENG DolbyD 5.1CH 48k/3
¡If you use DIGITAL AUDIO OUT jack, the sound
mode of audio CDs can not be changed.
AUDIO 2.FRE DolbyD 5.1CH 48k/3
AUDIO 3.JPN DolbyD 5.1CH 48k/3
Bon jour
HELLO
For audio CDs
Press the AUDIO button during playback.
¡Pressing the AUDIO button cycles the sound mode
through STEREO, L-CH and R-CH.
AUDIO STEREO
Both right and left channels
are active (stereo).
AUDIO L-CH
Only the left channel is active.
AUDIO R-CH
Only the right channel is active.
EN
–
–
31
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
¡It may take time to display the subtitles in the
selected language.
¡The screen display will disappear after about 5
CHANGING THE SUBTITLE
LANGUAGE
seconds.
DVD
¡When “SUBTITLE NOT AVAILABLE” appears on
screen, it means that no subtitle has been recorded.
The DVD/VCR has a function which allows you to
select the desired language for subtitles.
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures)
1
Press the SUBTITLE button during playback,
and then press the SUBTITLE button to select the
desired subtitle language.
DVD
¡The subtitle language can be changed if the subtitles
are recorded in multiple languages on the DVD
being played.
The DVD/VCR has a function which allows you to
select the desired camera angle.
¡The subtitle language cannot be changed if the
subtitles are recorded in a single language on the
DVD being played.
1
Press the ANGLE button during playback.
¡If the disc contains sequences recorded from differ-
ent camera angles, the angle icon ( ) will appear
at the top-right of the screen. You can change the
camera angle when the icon appears on the screen.
SUBTITLE 1.ENG/6
Subtitle 1
¡The camera angle cannot be changed if the disc does
not contain sequences recorded from different
camera angles.
SUBTITLE 2.FRE/6
Subtitle 2
SUBTITLE OFF
2
Press the ANGLE button while the angle
number is shown on the screen.
OFF
ANGLE 1 / 8
Angle 1
¡Pressing the SUBTITLE button cycles the subtitle
language from SUBTITLE 1, SUBTITLE 2 and all
the languages recorded.
¡The current subtitle mode will be displayed when
you first press the SUBTITLE button.
ANGLE 2 / 8
Angle 2
¡Press the SUBTITLE button, and then press the
Arrow buttons (s/ B) to set it to on or off.
ANGLE 8 / 8
Angle 8
Notes
¡The screen display will disappear after about 5
seconds.
Bon jour
HELLO
¡The current camera angle will be displayed when
you first press the ANGLE button.
Notes
¡Some discs allow subtitle language setting on the
disc menu. (Operation varies between discs, so refer
to the manual accompanying the disc.)
¡If the desired language is not shown after pressing
the SUBTITLE button several times, the disc does
not have subtitles in that language.
¡The subtitle language resets to the one which was
selected in the setup mode, every time the power is
turned on or discs are replaced. If that
language is not available on a disc, a language
defined by the disc is selected.
EN
–
–
32
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE ON-SCREEN
DISPLAY
2
Press the DISPLAY button again.
DVD
CD
ALL 4/12 0:13:45 -0:45:40 B
ALL:
TIME:
You can check the information regarding the disc by
pressing the DISPLAY button on the remote control.
Current track number
/ the total number of
tracks.
Elapsed time of the
current disk and
remaining time of
the current disc.
For DVDs
¡Use the Number buttons to start from a desired track.
1
Press the DISPLAY button during playback.
3
Press the DISPLAY button or the RETURN but-
ton to exit the display.
CH 7/49 0:01:46 -0:03:27
TIME:
CH (Chapter):
Elapsed time of the
current chapter and
remaining time of the
current chapter.
Current chapter number
/ the total number of
chapters.
BLACK LEVEL SETTINGS
DVD
You can select the BLACK LEVEL ON to make the
black areas of the picture brighter.
2
Press the DISPLAY button again.
TT 1/2 0:00:00 -1:23:45
1
Press the MODE button during playback.
TT(Title):
TIME:
Current title number
/ the total number of
titles.
¡The setup screen is displayed.
Elapsed time of the
current title and remaining
time of the current title.
:
BLACK LEVEL ON
2
Press the ENTER button to turn it on or off.
¡Use the Number button to start from the desired
chapter.
¡ON: This makes the dark parts brighter. (Default:
ON)
OFF: The original picture which is recorded on the
disc will be shown.
3
Press the DISPLAY button again.
¡Press the RETURN button to exit the display.
BIT RATE indicator will appear.
BIT RATE shows the quantity of
information which is recorded on the DVD.
BIT RATE
C L0
TruSurround SETTINGS
Layer number (*)
L0: Layer 0 is playing
L1: Layer 1 is playing
Current Repeat setting
C: Chapter repeat
T: Title repeat
You can enjoy stereophonic sound system when you
playback Dolby Digital and PCM 48 kHz sound.
A
B: A-B repeat
* appears when a layered disc is playing.
1
Press the MODE button twice during playback.
¡The setup screen will appear.
SRS TruSurround ON
4
Press the DISPLAY button or the RETURN but-
ton to exit the display.
2
Press the ENTER button to set it on or off.
ON: TruSurround ON.(Default : OFF)
OFF: TruSurround OFF.
¡Press the DISPLAY button ( you may have to press
it more than once), or press the RETURN button to
exit the display.
For audio CDs
1
Press the DISPLAY button during playback.
TR 4/12 0:03:21 -0:02:15 B
TR (Track):
¡SRS TruSurround is available only when the
DVD/VCR is connected to a TV or a stereo using the
red and white AUDIO OUT jacks on the DVD/VCR.
TIME:
Current track number
/ the total number of
tracks.
Elapsed time of the
current track and
remaining time of
the current track.
EN
–
–
33
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP ITEMS
PLAYER MENU:
(The on-screen display appears in selected language.)
LANGUAGE SETTINGS
SET-UP
LANGUAGE CONTROLS
DVD
1.AUDIO
ORIGINAL
OFF
ORIGNAL
ENGLISH
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
1
Press the SETUP button in STOP mode.
¡The setup screen is displayed.
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
4
Press the Arrow buttons (K/L) to select a
desired item, and then press the ENTER but-
ton.
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
¡If “OTHER” is selected on the AUDIO, SUBTITLE
or DISC MENU setting screen, the Language Code
setting screen will appear. Press the Number buttons
to enter the desired language code while referring to
2
3
Press the Arrow buttons (K/L) to select
Language, and then press the ENTER but-
ton.
SET-UP
the list on page 38.
1.LANGUAGE
2.DISPLAY
3.AUDIO
SET-UP
LANGUAGE CONTROLS
DISC MENU
LANGUAGE CODE
4.PARENTAL
Please enter a 4-digit Language code.
- - - -
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
EXIT: SETUP
CANCEL: RETURN
Press the Arrow buttons (K/L) to select an
item, and then press the ENTER button.
5
Press the SETUP button.
AUDIO:
(Voice is played in selected language.)
¡The setup mode will be canceled and the ordinary
screen is displayed.
SET-UP
LANGUAGE CONTROLS
1.AUDIO
ORIGINAL
OFF
ORIGNAL
ENGLISH
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
Notes
¡Language Setting for Audio and Subtitle is not avail-
able with some discs, so use the Audio and the
Subtitle button. Details are on pages 31 and 32.
¡You can also select an item by entering the number
besides it using the Number buttons.
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
SUBTITLE:
(Subtitles are shown in selected language.)
SET-UP
¡When you change the setup items, press the STOP
LANGUAGE CONTROLS
button if you are in playback mode.
1.AUDIO
ORIGINAL
OFF
ORIGNAL
ENGLISH
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
¡While the setup menu is shown, you can not open or
close the tray.
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
DISC MENU:
(The disc menu appears in selected language.)
SET-UP
LANGUAGE CONTROLS
1.AUDIO
ORIGINAL
OFF
ORIGINAL
ENGLISH
2.SUBTITLE
3.DISC MENU
4.PLAYER MENU
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
EN
–
–
34
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY SETTINGS
ANGLE ICON (Default: ON)
Display or not display the Angle icon on the screen.
DVD
SET-UP
DISPLAY CONTROLS
1
Press the SETUP button in STOP mode.
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4:3 LETTER BOX
BRIGHT
ON
4.AUTO POWER OFF ON
5.BACKGROUND BLUE
¡The setup screen will appear.
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
SET-UP
:
SETUP
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
AUTO POWER OFF (Default: ON)
Set or not set to turn off after the screen saver is started and
no keys are pressed for 35 minutes.
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
SET-UP
DISPLAY CONTROLS
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4.AUTO POWER OFF ON
5.BACKGROUND BLUE
4:3 LETTER BOX
BRIGHT
ON
2
Press the Arrow buttons (K/L) to select
DISPLAY and then press the ENTER button.
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
SET-UP
:
SETUP
1.LANGUAGE
2.DISPLAY
3.AUDIO
BACKGROUND COLOR (Default: BLUE)
Select blue or gray.
4.PARENTAL
SELECT:
EXIT
/
SET
:
ENTER
RETURN
:
SETUP CANCEL
:
SET-UP
DISPLAY CONTROLS
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4:3 LETTERBOX
BRIGHT
ON
3
Press the Arrow buttons (K/L) to select an
item, and then press the ENTER button.
4.AUTO POWER OFF ON
5.BACKGROUND BLUE
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
TV ASPECT (Default: 4:3 LETTER BOX)
4:3 LETTER BOX: Wide screen with black bars on top and
bottom
4:3 PAN & SCAN: Full height picture, trimmed both sides
16:9 WIDE: If wide screen TV is connected
4
5
Press the Arrow buttons (K/L) to select a
desired item, and then press the ENTER button
to change the setting.
SET-UP
DISPLAY CONTROLS
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4.AUTO POWER OFF ON
5.BACKGROUND BLUE
4:3 LETTER BOX
BRIGHT
ON
Press the SETUP button.
SET-UP
DISPLAY CONTROLS
SELECT:
EXIT
/
SET
:
ENTER
RETURN
¡The setup mode will be canceled and the ordinary
TV ASPECT
:
SETUP CANCEL
:
1.4:3 LETTER BOX
2.4:3 PAN & SCAN
3.16:9 WIDE
screen will appear.
Notes
SELECT:
EXIT
/
SET
:
ENTER
RETURN
¡You can also select an item by entering the number
:
SETUP CANCEL
:
besides it using the Number buttons.
PANEL DISPLAY (Default : BRIGHT)
Adjust the brightness of the display of the unit.
Auto: Stays dim only during playback.
SET-UP
DISPLAY CONTROLS
1.TV ASPECT
2.PANEL DISPLAY
3.ANGLE ICON
4:3 LETTER BOX
BRIGHT
ON
SET-UP
DISPLAY CONTROLS
PANEL DISPLAY
4.AUTO POWER OFF ON
5.BACKGROUND BLUE
SELECT:
EXIT
/
SET
:
ENTER
RETURN
:
SETUP CANCEL
:
1.BRIGHT
2.DIMMER
3.AUTO
SELECT:
/
SET
:
ENTER
EXIT:
SETUP CANCEL
:
RETURN
EN
–
–
35
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
DTS (Default: OFF)
AUDIO SETTINGS
On : Output DTS sound
Set to On when the unit is connected to DTS
Decoder.
DVD
SET-UP
AUDIO CONTROLS
1
Press the SETUP button in STOP mode.
1.DRC
2.DOLBY DIGITAL
3.DTS
OFF
ON
OFF
AUTO
SET-UP
¡The setup screen will appear.
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.DOWN SAMPLING
4.PARENTAL
SELECT:
EXIT
/
SET
:
ENTER
RETURN
:
SETUP CANCEL
:
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
:
SETUP
Down Sampling (Default: AUTO)
Set the output for the DVD
recorded in PCM 96 kHz (96 kHz or 48 kHz)
2
Press the Arrow buttons (K/L) to select
Audio and then press the ENTER button.
SET-UP
¡Press the Arrow buttons (K/L) to select an item, and
then press the ENTER button.
1.LANGUAGE
2.DISPLAY
3.AUDIO
4.PARENTAL
SETUP MENU
SELECT:
EXIT
/
SET
:
ENTER
RETURN
AUDIO OPTIONS
:
SETUP CANCEL
:
1.DRC
2.DOLBY DIGITAL
3.DTS
OFF
ON
OFF
AUTO
4.DOWN SAMPLING
3
Press the Arrow buttons (K/L) to select an
item, and then press the ENTER button.
SELECT:
EXIT
/
SET
:
ENTER
RETURN
SET-UP
AUDIO CONTROLS
DOWN SAMPLING
:
SETUP CANCEL
:
DRC (Default: OFF)
1.AUTO
2.48kHz
3.96kHz
On: DRC
(Dynamic Range Control)
SELECT:
/
SET
:
ENTER
RETURN
EXIT:
SETUP CANCEL
:
¡This function is for controlling the range of sound
volume. By compressing the range of sound volume,
it is possible not only to suppress the output of loud
sound at night and but also to raise the volume of
low sound.
When playing a disc with copyright protection
¡If you select 96 kHz, copyright protection will be
activated and no sound will come out. If you select
AUTO, sound will be down sampled at 48 kHz.
¡This function is effective only for the sound record-
ed by Dolby Digital recording.
4
Press the SETUP button.
SET-UP
AUDIO CONTROLS
¡The setup mode will be canceled and the ordinary
screen will appear.
1.DRC
2.DOLBY DIGITAL
3.DTS
OFF
ON
OFF
AUTO
4.DOWN SAMPLING
SELECT:
EXIT
/
SET
:
ENTER
RETURN
:
SETUP CANCEL
:
Dolby Digital (default: ON)
On : Output by Dolby Digital
Set to On when the unit is connected to a Dolby
Digital Decoder.
SET-UP
AUDIO CONTROLS
1.DRC
2.DOLBY DIGITAL
3.DTS
OFF
ON
OFF
AUTO
4.DOWN SAMPLING
SELECT:
EXIT
/
SET
:
ENTER
RETURN
:
SETUP CANCEL
:
EN
–
–
36
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
When Parental Level is selected
PARENTAL LOCK
¡Press the Arrow buttons (K/L) to
select an item from “ALL” or 8 to
1 and then press the ENTER but-
ton.
DVD
1
Press the SETUP button in STOP mode.
SET-UP
PARENTAL CONTROLS
¡The setup screen will appear.
1.PARENTAL LEVEL
2.CHANGE
ALL
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
SET-UP
PARENTAL CONTROLS
PARENTAL LEVEL
SELECT:
EXIT
/
SET
:
ENTER
RETURN
:
SETUP CANCEL
:
4.PARENTAL
ALL
8
7
6
5
[NC-17]
[R]
SELECT:
/
SET
:
ENTER
RETURN
EXIT:
SETUP CANCEL
:
SELECT:
EXIT
/
SET
:
ENTER
RETURN
:
SETUP CANCEL
:
2
Press the Arrow buttons (K/L) to select
PARENTAL, and then press the ENTER but-
ton.
5
Press the SETUP button.
SET-UP
1.LANGUAGE
2.DISPLAY
3.AUDIO
¡The setup mode will be canceled and the ordinary
4.PARENTAL
CONTROL LEVELS
SELECT:
EXIT
/
SET
CANCEL: RETURN
:
ENTER
¡
ALL
:
SETUP
All parental lock is cancelled.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
3
Press the Number buttons to enter a 4-digit
password (you can use any 4-digits except
for 4737), and then press the ENTER button.
¡
Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
¡This number will be used as the password from the
second time onward.
¡By entering the password, you can then change the
¡
Level 1
control level and password settings.
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
¡If you want to change the password, select
“CHANGE” and
enter a new pass-
word. Then press
SET-UP
PARENTAL CONTROLS
Notes
PASSWORD
the ENTER button.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
Please enter a 4-digit password.
- - - -
EXIT:
SETUP
CANCEL: RETURN
¡Record the password in case you forget it.
IF YOU FORGET THE PASSWORD
1) Press 4, 7, 3, and 7 at Step 3.
4
Press the Arrow buttons (K/L) buttons to
select an item, and then press the ENTER but-
ton.
¡Password will be cleared and parental level will be
set to ALL.
2) Proceed the above Steps 3-5 again.
EN
–
–
37
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE CODE LIST
Language
Country code
Language
Country code
No.
No.
1
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
Latvian; Lettish
Malagasy
Maori
4 7 4 7
4 7 4 8
4 7 5 2
4 7 5 9
4 7 6 4
4 7 6 5
4 7 7 1
4 7 7 2
4 8 4 7
4 8 5 1
4 8 5 3
4 8 5 4
4 8 5 5
4 8 6 0
4 8 6 1
4 8 6 4
4 9 4 7
4 9 6 1
4 9 6 5
4 9 7 1
5 0 4 7
5 0 5 1
5 0 7 2
5 1 5 8
5 1 6 0
5 1 6 1
5 1 6 5
5 1 6 6
5 1 6 7
5 2 4 7
5 2 5 5
5 2 5 6
5 2 6 1
5 2 6 4
5 2 7 1
5 3 4 7
5 3 5 0
5 3 5 8
5 3 6 0
5 3 6 7
5 4 4 7
5 4 5 5
5 4 6 4
5 4 6 7
5 4 7 1
5 5 4 7
5 5 5 1
5 5 5 7
5 5 6 0
5 5 6 5
5 5 6 6
5 5 6 9
5 6 4 7
5 6 5 5
5 6 6 9
5 7 4 7
5 7 5 7
5 7 5 8
5 7 5 9
5 7 6 0
5 7 6 1
5 7 6 5
5 7 6 7
5 7 7 1
5 8 4 7
5 8 6 0
5 8 6 1
5 8 6 6
5 8 6 8
5 9 5 3
5 9 5 5
5 9 5 7
5 9 5 8
5 9 6 0
5 9 6 1
5 9 6 4
5 9 6 5
5 9 6 6
5 9 7 1
6 0 4 7
6 0 5 1
6 0 5 8
6 0 6 1
6 1 4 9
6 1 5 9
6 1 6 4
6 2 4 7
6 2 5 8
6 2 6 5
6 2 6 6
6 3 6 7
6 4 5 9
6 4 6 0
6 4 6 1
6 4 6 7
6 4 6 9
6 5 4 7
6 5 5 0
6 5 5 3
6 5 5 4
6 5 5 5
6 5 5 7
6 5 5 8
6 5 5 9
6 5 6 0
6 5 6 1
6 5 6 3
6 5 6 4
6 5 6 5
6 5 6 6
6 5 6 7
6 5 6 8
6 5 6 9
6 6 4 7
6 6 5 1
6 6 5 3
6 6 5 4
6 6 5 5
6 6 5 7
6 6 5 8
6 6 6 0
6 6 6 1
6 6 6 4
6 6 6 5
6 6 6 6
6 6 6 9
6 7 5 7
6 7 6 4
6 7 7 2
6 8 5 5
6 8 6 1
6 9 6 1
7 0 5 4
7 1 6 1
7 2 5 4
7 2 6 7
Afar
2
Abkhazian
Afrikaans
Amharic
3
4
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
5
Arabic
6
Assamese
Aymara
7
8
Azerbaijani
Bashkir
9
Malay
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Maltese
Byelorussian
Bulgarian
Bihari
Burmese
Nauru
Nepali
Bislama
Dutch [DUT]
Norwegian [NOR]
Occitan
Bengali; Bangla
Tibetan
Breton
(Afan) Oromo
Oriya
Catalan
Corsican
Czech
Panjabi
Polish
Welsh
Pashto; Pushto
Portuguese [POR]
Quechua
Danish [DAN]
German [GER]
Bhutani
Rhaeto-Romance
Kirundi
Greek [GRE]
English [ENG]
Esperanto
Spanish [SPA]
Estonian
Basque
Romanian [RUM]
Russian [RUS]
Kinyarwanda
Sanskrit
Sindhi
Sangho
Persian
Finnish [FIN]
Fiji
100 Serbo-Croatian
101 Singhalese
102 Slovak
Faroese
French [FRE]
Frisian
103 Slovenian
104 Samoan
105 Shona
106 Somali
107 Albanian
108 Serbian
109 Siswat
Irish [IRI]
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
110 Sesotho
111 Sundanese
112 Swedish [SWE]
113 Swahili
114 Tamil
Hindi
Croatian
Hungarian [HUN]
Armenian
Interlingua
Interlingue
Inupiak
115 Telugu
116 Tajik
117 Thai
Indonesian
Icelandic [ICE]
Italian [ITA]
Hebrew
118 Tigrinya
119 Turkmen
120 Tagalog
121 Setswana
122 Tonga
Japanese
Yiddish
123 Turkish [TUR]
124 Tsonga
125 Tatar
Japanese [JPN]
Georgian
Kazakh
126 Twi
Greenlandic
Cambodian
Kannada
Korean [KOR]
Kashmiri
Kurdish
127 Ukrainian
128 Urdu
129 Uzbek
130 Vietnamese
131 Volapuk
132 Wolof
Kirghiz
133 Xhosa
Latin
134 Yoruba
135 Chinese [CHI]
136 Zulu
Lingala
Laothian
Lithuanian
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change
the Audio or Subtitle language setting on pages 31 and 32. If you choose any other languages, ‘---’ will be dis-
played instead. (3 letter language codes are written in square brackets.)
EN
–
–
38
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If the DVD/VCR does not perform properly when operated as instructed in this Owner's Manual, check the
player consulting the following checklist.
PROBLEM
No power.
CORRECTIVE ACTION
D
V
D
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
The player does not respond to. • Check if the power plug is connected to an AC outlet.
the remote control.
.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the
obstacles between the sensor and the remote.
• You have to be within 7 m of the player.
• Check if the correct mode is selected. If not switch the mode by pressing the DVD or
the VCR button, whichever you need, on the remote control.
V
C
R
Timer recording is impossible. • Make sure the timer recording is set correctly.
• Make sure the power is off.
V
C
R
• Make sure the DVD/VCR clock is set correctly.
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Put he player in VCR mode. Press the VCR button on the remote control so that the green
VCR OUTPUT light is lit.
(
)
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing the CHANNEL button
on the
DVD/VCR.
Cannot view a tape but the
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
• Make sure the DVD/VCR is not in the Menu mode.
.
audio is OK
No, or poor, playback picture.
• Select channel 3 or 4 on your TV, then press the VCR/TV button so that the VCR/TV
indicator on the VCR comes on.
• Fine tune your TV.
TV programs cannot be seen
normally.
• Re-check the ANT. IN and ANT. OUT connections. See page 14.
• Press the VCR/TV button so that the VCR/TV indicator on the DVD/VCR disappears.
• Press the VCR button on the remote control to put it in the VCR mode. Check if the green
VCR OUTPUT light is lit. Then, set it to the TV position by pressing the VCR/TV button.
The VCR/TV light goes off.
Video or color fades in and out
when making a copy of a video tape.
•
You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
Cannot remove the tape.
• Check if the player is in the VCR mode. If not, press the VCR button on the remote control
to switch the mode.
No picture.
• Connect the video cables firmly.
D
V
D
• Insert a correct video disc that plays on this player.
• Press the DVD button on the remote control. Check if the DVD OUTPUT Light is lit. Then
try other DVD feature buttons.
• Insert the disc.
• Clean the disc.
.
Disc cannot be played
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
.
No sound
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
.
• Connect the player directly to the TV.
Distorted picture
•
There are some cases where pictures may be slightly distorted, which are not a sign of a mal-
function.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
does not match the set up
•
The selected language is not available for audio or subtitles on the DVD.
This is not a malfunction
The camera angle cannot be
changed.
• The DVD does not contain sequences recorded from different camera angles.
This is not a malfunction.
Audio or subtitle language
cannot be changed.
• The DVD does not contain audio source or subtitles in the selected language.
This is not a malfunction.
• That operation is prohibited by the player or the disc.
This is not a malfunction.
“Prohibited icon” appears on the
screen, prohibiting an operation.
Notes
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this
Owner’s Manual for details on correct operations.
¡Playback from a desired track and random playback are not available during program playback.
EN
–
–
39
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLING PRECAUTIONS
AUTO HEAD CLEANING
SERVICING
• Automatically cleans video heads as you insert or remove a
cassette, so you can see a clear picture.
Should your DVD/VCR become inoperative, do not try
to correct the problem by yourself. There are no user-
serviceable parts inside. Turn off, unplug the power
cord, and please call our help line at 1-800-968-3429 to
locate an Authorized Service Center.
• Playback picture may become blurred or interrupted while
the TV program reception is clear. Dirt accumulated on the
video heads after long periods of use, or the usage of
rental or worn tapes can cause this problem. If a streaky or
snowy picture appears during playback, the video heads in
your DVD/VCR may need to be cleaned.
CABINET CLEANING
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
¡Wipe the front panel and other exterior surfaces of
the DVD/VCR with a soft cloth immersed in
lukewarm water and wrung dry.
2. If a Video Head Cleaner does not solve the problem,
please call our help line at 1-800-968-3429 to locate an
Authorized Service Center.
¡Never use a solvent or alcohol. Do not spray
insecticide liquid near the DVD/VCR. Such
chemicals may cause damage and discoloration to
the exposed surfaces.
NOTES:
• Remember to read the instructions included with the video
head cleaner before use.
• Clean video heads only when problems occur.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
¡If the player still does not perform properly when it is operated while referring to the relevant sections and to the
TROUBLESHOOTING GUIDE in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your
dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
¡Use discs which have the following logos on them. ¡To clean-off, use a soft cloth.
(Optical audio digital discs.)
¡Do not use a hard cloth since this will mar the disc.
¡Wipe the disc in a straight line from center to edge.
¡Never wipe with a circular motion.
¡Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
¡Do not use detergent or abrasive cleaning agents.
¡Always store the disc in its protective case when it is
not used.
EN
–
–
40
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Product type:
Discs:
DVD player with Video Cassette Recorder
DVD video
Audio CD
Video Cassette tape
Converter output:
Power source:
VHF Channel 3 or 4.
120 V AC +/- 10%, 60 Hz +/- 0.5%
25 W (standby: 7.2 W)
5°C to 40°C
Power consumption:
Operating temperature:
Dimensions:
W 17-1/8” (435 mm)
H 4” (99 mm)
D 10-1/2” (266 mm)
8.8 lbs (4 kg)
Weight:
¡Designs and specifications are subject to change without notice.
¡If there is a discrepancy between languages, the default language will be English.
EN
–
–
41
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES
PANEL DELANTERO
1
2
3
4
5
6
7 8 9
POWER
VIDEO
L
CHANNEL
DVD OPERATION
OUTPUT
VCR OPERATION
TIMER
SET
AUDIO
R
VCR/TV
CST.IN
OPEN/CLOSE
STOP
SKIP/REV PLAY
FWD/SKIP
STOP/EJECT REW
PLAY
F.FWD REC/OTR
25
23 21
22
19 17 15 13 11
18 16 14 12 10
PANEL REMOTO
26
24
20
Conecte aquí un cable de videó procedente de la toma de
salida de videó de un camcorder, otro VCR o una fuente de
videó (reproductor de discos láser, camcorder, etc.).
56
54
27
POWER SPEED AUDIO
28
10. Tomas AUDIO IN
Conecte aquí cables de audio procedentes de las tomas de sali-
da de audio de un camcorder, otro VCR o una fuente de audio.
11. Botón TIMER SET
1
4
7
2
5
8
0
3
6
55
53
SKIP/CH.
29
VCR/TV
SLOW
9
+100
Presione para poner el DVD/VCR en modo de espera para
una grabación con temporizador.
+
10
VCR
DISPLAY DVD
PAUSE
12. Luz CASSETTE IN
52
50
30
32
34
Se enciende cuando un cassette está en el DVD/VCR.
13. Luz VCR/TV
51
49
31
33
PLAY
Se enciende cuando el DVD/VCR está en la posición VCR,
y se apaga cuando está en la posición TV.
14. Botones CHANNEL
STOP
RECORD
MENU
48
46
En el modo VCR, presione para cambiar canales TV en el
DVD/VCR; presione para ajustar el seguimiento durante
reproducción de movimiento normal o lento; presione para
remover fluctuaciones verticales en una imagen fija.
15. Botón REC/OTR (VCR)
35
37
39
ENTER
47
36
38
SETUP
TITLE
RETURN
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
45
43
44
42
SUBTITLE ANGLE REPEAT
A
B
Presiones una vez para iniciar una grabación. Presione
repetidamente para iniciar un grabación de Un-Toque.
16. Botón F.FWD (VCR)
40
41
Presione para avanzar rápidamente la cinta o ver la
1. Bandeja de carga del disco
2. Luz DVD OUTPUT (verde)
imagen rápidamente en avance durante reproduc-
ción. (Búsqueda en Avance). Cuando ajuste progra-
ma. (Por ejemplo: ajuste reloj o programa con tem-
porizador), presione para determinar su selección y
proceder al siguiente paso que usted desea entrar.
Presione para determinar los modos de ajuste del
menú en pantalla. Presione para añadir o cancelar
números de canal durante preajuste de canal.
17. Botón PLAY (VCR)
Esta luz aparece cuando el DVD/VCR está en modo DVD.
Usted sólo puede mirar DVDs cuando la Luz DVD OUT-
PUT verde está encendida. Para hacer que la Luz DVD
OUTPUT verde se encienda, presione el Botón DVD en el
control remote o el Botón OUTPUT en el panel delantero.
3. Luz VCR OUTPUT (Verde)
Esta luz aparece cuando el DVD/VCR está en el modo
VCR. Usted puede sólo mirar cintas cuando la Luz VCR
OUTPUT verde está encendida. Para hacer que la Luz VCR
OUTPUT verde se encienda, presione el Botón VCR en el
control remote o el Botón OUTPUT en el panel delantero.
4. CASSETTE COMPARTMENT
P
resione para comenzar reproducción. Presione para
entrar dígitos cuando ajuste programa. (Por ejemplo:
ajuste reloj o programa con temporizador). Presione
para seleccionar los modos de ajuste del menú en
pantalla.
5. Luz REC/OTR
18. Botón REW (VCR)
Se enciende durante la grabación.
Presione para rebobinar la cinta o para ver la imagen
6. Luz TIMER SET
rápidamente en inversión durante el modo de repro-
ducción.(Búsqueda en Rebobinado). Presione para
cancelar un ajuste de programa con temporizador.
Presione para corregir dígitos cuando ajuste progra-
ma. (Por ejemplo: ajuste de reloj o programa con
temporizador). Presione para añadir o cancelar
números de canal durante preajuste de canal.
19. Botón STOP/EJECT (VCR)
Esta luz brilla cuando el DVD/VCR está en el modo espera
o apagada para una grabación con temporizador o durante
una grabación de Un-Toque, Parpadea si se presiona Botón
TIMER SET para una grabación con temporizador, pero no
hay cinta en el DVD/VCR. Parpadea cuando todas las
grabaciones con temporizador o grabaciones de Un-Toque
han terminado.
7. Botón POWER
GBotón de expulsión
Púlselo para sacar el videocasete de la
Presione para conectar y desconectar la alimentación.
8. Luz POWER
videograbadora.
Se enciende cuando la alimentación está conectada.
9. Toma VIDEO IN
G
Botón Stop
Presione detener el movimiento de la cinta.
SP
–
–
42
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
Presione para entrar dígitos cuando ajuste progra-
ma. (Por ejemplo: ajuste reloj o programa con tem-
porizador). Presione para seleccionar los modos de
ajuste del menú en pantalla.
programa con temporizador). Presione para añadir
o cancelar números de canal durante preajuste de
canal.
33. Botón Stop
20. Botón OUTPUT
Presione detener el movimiento de la cinta.
Presione para entrar dígitos cuando ajuste progra-
ma. (Por ejemplo: ajuste reloj o programa con tem-
porizador). Presione para seleccionar los modos de
ajuste del menú en pantalla.
Presione para seleccionar el modo DVD o el modo VCR.
G Usted puede cambiar el modo de salida ya presionando
el Botón OUTPUT en el panel delantero o ya presionan-
do el Botón DVD o VCR en el control remote. Sin
embargo, si usted presiona el Botón OUTPUT en el
panel delantero primero, usted necesita volver a
seleccionar el modo correspondiente presionando el
Botón DVD o el Botón VCR en el control remote.
21. Botón FWD/SKIP (DVD)
34. Botón RECORD
Presione para iniciar una grabación. O, presione repetida-
mente para iniciar una grabación de Un-Toque.
35. Botón MENU
GModo DVD
Reproduce desde el inicio del siguiente capítulo o pista.
Retenga abajo para avanzar rápidamente la reproducción.
22. Botón PLAY (DVD)
Presione para visualizar el menú del Disco.
GModo VCR
Presione para tener acceso al menú VCR.
36. Botón TITLE
Comienza la reproducción del contenido del disco.
23. Botón SKIP/REV (DVD)
37. Botón SETUP
Reproduce desde el inicio del capítulo o pista actual.
Retenga abajo para reproducción inversa rápida.
24. Botón STOP (DVD)
Presione para entrar el modo de preparación.
38. Botón ZOOM
Amplía parte de una imagen reproducida-DVD.
39. Botón MODE
Detiene la operación del disco.
25. Botón OPEN/CLOSE
Activa modo de reproducción de programa o reproducción
aleatoria cuando se reproducen CDs o MP3. Ajusta Nivel
de negro o TruSurround SRS.
Presione para insertar discos en o removerlos de la bandeja
de disco.
26. Ventanilla de Sensor Remoto, Visualización
40. Botón SUBTITLE
27. Botón SPEED
Presione para seleccionar un idioma de subtítulo deseado.
41. Botón ANGLE
Presiona para seleccionar la velocidad de grabación de
VCR (SP o SLP)
Presione para cambiar el ángulo de cámara para ver la
secuencia que se está reproduciendo desde un ángulo difer-
ente.
28. Botón POWER
Presione para conectar y desconectar la alimentación.
29. Botones numéricos
42. Botón REPEAT
GModo DVD
Repite la reproducción del disco, título, capítulo o pista
actual.
Presione para seleccionar directamente una Pista (CD de
Audio) para reproducción.
43. Botón A-B REPEAT
Presione para programar Pistas (Dcde Audio) para repro-
ducir.
Repite la reproducción de una sección seleccionada.
44. Botón SEARCH MODE
GModo VCR
GModo DVD
Presione para seleccionar canales de TV en el DVD/VCR.
Para seleccionar canales, entre números de canal como un
número de dos dígitos para los resultados más rápidos.
Por ejemplo, para seleccionar canal 6, presione 0.6.
Botón +100:
Presione para tener acceso o remover la indicación de
búsqueda, que le permite ir directamente
Título/Capítulo/Pista/Tiempo especificado.
GModo VCR
a
un
Presione para avanzar o rebobinar rápidamente la cinta a
una longitud específica de tiempo.
45. Botón CLEAR/C.RESET
GModo DVD
Si usted desea seleccionar canales 100 y arriba, presione
este Botón primero, luego presione los dos dígitos últi-
mos. Por ejemplo, para seleccionar canal 125, presione
Botón “+100” primero, luego presione “2” y “5”.
30. Botón DISPLAY
Presione para reponen el ajuste.
GModo VCR
Presione para reponer el contador. Presione para salir de
la pantalla MEMU.
GModo DVD
Presione para tener acceso o remover la pantalla de visu-
alización durante reproducción DVD o CD de audio.
GModo VCR
46. Botón RETURN
Vuelve a la operación previa.
Presione para tener acceso o remover visualización de
estado en pantalla de VCR.
47. Botones de flecha
Utilice cuando haga ajustes mientras mira la indicación en
una pantalla de TV.
31. Botón DVD
Presione antes de utilizar el control remote para funciones
DVD.
48. Botón ENTER
Presione para aceptar un ajuste.
49. Botón g
32. Botón h
GModo DVD
GModo DVD
Presione para ver la imagen DVD en movimiento de
inversión rápida o para invertir la reproducción de un
DC de Audio.
Presione para avanzar rápidamente el Disco. Presione el
Botón PAUSE, luego presione el Botón FWD iniciar a
reproducción en movimiento lento. Presione el Botón
FWD repetidamente para cambiar la velocidad de
avance del movimiento lento.
GModo VCR
Presione para rebobinar la cinta o para ver la ima-
gen rápidamente en inversión durante el modo de
reproducción.(Búsqueda en Rebobinado). Presione
para cancelar un ajuste de programa con tempo-
rizador. Presione para corregir dígitos cuando
ajuste programa. (Por ejemplo: ajuste de reloj o
GModo VCR
P
resione para avanzar rápidamente la cinta o ver la
imagen rápidamente en avance durante reproduc-
ción. (Búsqueda en Avance). Cuando ajuste pro-
grama. (Por ejemplo: ajuste reloj o programa con
SP
–
–
43
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
temporizador), presione para determinar su selec-
ción y proceder al siguiente paso que usted desea
entrar. Presione para determinar los modos de
ajuste del menú en pantalla. Presione para añadir o
cancelar números de canal durante preajuste de
canal.
Utilice para seleccionar la posición VCR o TV. Si la Luz
VCR/TV aparece en la parte delantera del DVD/VCR, está
en la posición VCR (en cualquier modo VCR o DVD). Si
la Luz VCR/TV no aparece en la parte delantera del
DVD/VCR, está en la posición TV.
GPosición VCR
Cuando la Luz VCR OUTPUT verde aparece en la parte
delantera del DVD/VCR, utilice la VCR para mirar una cinta,
para mirar un programa de TV mientras lo graba o para mirar
una radiodifusión de TV utilizando los botones CHANNEL o
Numéricos para cambiar canales en la DVD/VCR.
Cuando la Luz DVD/VCR aparece en la parte delantera de la
DVD/VCR, utilice el DVD/VCR para mirar la reproducción
de Disco o menús.
50. Botón PLAY
Presione para comenzar reproducción. Presione
para entrar dígitos cuando ajuste programa. (Por
ejemplo: ajuste reloj o programa con tempo-
rizador). Presione para seleccionar los modos de
ajuste del menú en pantalla.
51. Botón VCR
Presione antes de utilizar el control remote para fun-
ciones de VCR.
GPosición de TV
Utilice para mirar TV (cambiando canales en el TV) o
para mirar un programa mientras graba otro.
55. Botones SKIP/CH
52. Botón PAUSE
GModo DVD
Presione para pausar la reproducción de Disco. Presione
repetidamente para avanzar la imagen DVD paso a paso
(o un fotograma cada vez).
GModo DVD
Presione para saltar Capítulos o Pistas.
GModo VCR
GModo VCR
Presione para cambiar canales de TV en la DVD/VCR.
56. Botón AUDIO
Mientras graba, presione para detener provisionalmente
la grabación (pausa). Presione por segunda vez para
reanudar la grabación normal. Usted no puede pausar
Grabación de Un-Toque. O, presione durante la repro-
ducción de cinta para congelar la imagen.
53. Botón SLOW
Presione para seleccionar un idioma de audio deseado o
modo de sonido.
Notas
¡
Para utilizar el control remote para operar el DVD/VCR y
sus funciones, presione el Botón DVD en el control remote
antes de presionar otros botones DVD. Verifique que la
Luz DVD OUTPUT verde está encendida.
Durante la reproducción de cinta, presione mirar la cinta de
videó a movimiento lento. Presione de nuevo para reanudar
la reproducción normal. Este Botón no afecta la reproduc-
ción DVD.
¡
Para utilizar el control remote para operar la VCR y sus
funciones, presione el Botón VCR en el control remote
antes de presionar otros botones VCR. Verifique que la
Luz VCR OUTPUT verde está encendida.
54. Botón VDR/TV
VISIÓN TRASERA
57
58 59
60
DVD/VCR
OUT
COMPONENT
VIDEO OUT
IN
ANT - IN
Y
L
DVD/VCR
AUDIO OUT
AUDO
DIGITAL AUDIO OUT
PCM / BITSTREAM
COAXIAL
S-VIDEO
OUT
L
R
Cb
Cr
ANT - OUT
R
VIDEO
CH3 CH4
67 65
66
64
62
63
61
57. Cordón de Alimentación AC
62. Toma S-VIDEO OUT
Conecte a una toma de corriente AC estándar para sum-
inistrar corriente al DVD/VCR.
Conecte aquí un cable de S-Videó opcional y a la toma
de entrada de S-Videó de un televisor.
63. Toma DVD/VCR VIDEO OUT
58. Tomas AUDIO IN
Conecte aquí los cables de audio procedentes de las
tomas de salida de audio de un camcorder, otra VCR o
una fuente de audio.
Conecte aquí el cable de videó amarillo (provisto) y a la
toma de entrada de Videó de TV.
64. Toma VIDEO IN
59. Tomas DVD/VCR AUDIO OUT
Conecte aquí los cables de audio provistos y a las tomas
de entrada de audio de un televisor u otro equipo de
audio.
Conecte un cable procedente de la toma de salida de
videó de un camcorder, otra VCR o una fuente de audio-
visual (reproductor de disco láser, reproductor de disco
de videó, etc.) aquí.
60. Tomas COMPONENT VIDEO OUT
Conecte aquí los cables de videó componente
opcionales y a las tomas de entrada de Videó compo-
nente de un televisor.
65. Cambio CH3/CH4
Ajuste a canal 3 ó 4 para utilizar su TV con su
DVD/VCR.
66. Toma ANTI-IN (Entrada de Antena)
61. Toma COAXIAL
Conecte su antena o cable aquí.
Conecte aquí un cable de audio digital coaxial opcional
y a la toma de entrada Audio Digital Coaxial de un
descodificador o receptor de audio.
67. Toma ANT-OUT (Salida de Antena)
Utilice el cable coaxial RF provisto para conectar esta
toma a la Toma ANTENNA IN en su TV.
Caja de cables o Sistema de Radiodifusión Directa.
Notas
¡La toma S-VIDEO OUT, toma COAXIAL, toma OPTICAL y tomas COMPONENT VIDEO OUT son sólo
útiles en el modo DVD.
SP
–
–
44
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMBIO DE VCR/DVD
Como este producto se utiliza del reproductor VCR y DVD, es necesario cambiar uno del
otro.
CAMBIO AL MODO VCR
CAMBIO AL MODO DVD
Presione el Botón VCR en el control remote.
(Verifique que la Luz VCR OUTPUT está enendida.)
Presione el Botón DVD en el control remote.
(Verifique que la Luz DVD OUTPUT está encendida)
Notas
¡Presionando sólo el Botón OUTPUT en el panel delantero no cambia el modo del control remote. Usted siem-
pre necesita seleccionar el modo correcto en el control remote, también.
POWER
VIDEO
POWER SPEED AUDIO
DVD OPERATION
OUTPUT
VCR OPERATION
STOP/EJECT REW
CHANNEL
L
TIMER
SET
AUDIO
R
VCR/TV
CST.IN
OPEN/CLOSE
STOP
SKIP/REV PLAY
FWD/SKIP
PLAY
F.FWD REC/OTR
1
4
7
2
5
8
0
3
6
SKIP/CH.
VCR/TV
SLOW
9
+100
DVD OUTPUT Light
DVD button
VCR OUTPUT Light
+
10
DISPLAY DVD
VCR
PAUSE
VCR button
PLAY
VD OPERATION
OUTPUT
VCR OPERATIO
STOP
RECORD
MENU
ENTER
LAY
FWD/SKIP
STOP/EJECT REW
SETUP
TITLE
RETURN
SEARCH
MODE
CLEAR/
MODE ZOOM
C.RESET
OUTPUT button
SUBTITLE ANGLE REPEAT
A
B
SP
–
–
45
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
CONEXIONES
AJUSTANDO EL CONMUTADOR
CH3/CH4
DVD/VCR A CONEXIÓN DE TV
1. Desconecte el cordón de alimentación AC del toma de Si su TV no tiene terminales A/V:
corriente AC.
Cuando el DVD/VCR está en modo de Reproducción
VCR o cuando el DVD/VCR está en el modo VCR. su
2. Desconecte la antena o cable del TV.
3. Conecte la antena o cable a la toma ANT.IN del TV recibirá señales del DVD/VCR en cualquiera de
DVD/VCR.
los canales 3 ó 4. Para utilizar el DVD/VCR con su TV,
4. Conecte el DVD/VCR al TV utilizando el cable coaxi- ponga el conmutador selector en CH3 o CH4 (que está
al.
ubicado en la parte trasera de su DVD/VCR),
5. Enchufe los cordones de alimentación CA del cualquiera no se utilice para radiodifusiones normales
DVD/VCR y TV dentro de las tomas de corriente AC. en su área. Luego, ajuste su TV al mismo canal.
CONECTANDO A UN TV
Por favor, vea la [Fig.1] en la página 14 para detalles.
CONECTADO A UN TV QUE TIENE TOMA DE ENTRADA DE S-
VÍDEO o TOMAS DE ENTRADA DE VÍDEO COMPONENTE
Por favor, vea la [Fig. 2] en la página 14 para detalles.
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE
ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT
Por favor, vea la [Fig. 4] en la página 15 para detalles.
CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY O
DESCODIFICADOR DTS
Por favor, vea la [Fig. 5] en la página 16 para detalles.
CONECTANDO A UN AUDIO ANALÓGICO
Por favor vea la [Fig. 6] en la página 16 para detalles.
PREPARACIÓN
PREPARACIÓN DE CANAL AUTOMÁTICA
VCR
4 Inicie canal preajustado presionando [F.FWD]
una vez. El sintonizador explora y memoriza
todos los canales activos de su área.
1
2
Conecte elTV y ponga elTV en el canal 3 ó 4.
Conecte el DVD/VCR presionando [POWER].
Ambas Luces POWER y VCR/TV se encen-
derán.
5
Después de explorar, el sintonizador de
detiene en el canal memorizado más bajo. La
pantalla de TV retorna al modo TV.
3
Seleccione el Idioma en la pantalla (“INGLÉS”,
“FRANCÉS” o “ESPAÑOL”) presionando [PLAY] o
[STOP]. Luego, presione [F.FWD].
SP
–
–
46
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARACIÓN DE RELOJ
REPRODUCCIÓN DE UN DISCO
VCR
REPRODUCIENDO UN DVD,
VIDEO O UN CD AUDIO
Ajuste el reloj con precisión para grabación con tempo-
rizador automática adecuada. Le sugerimos que usted utilice
un TV o estación de radio como su fuente de tiempos.
DVD
CD
1
Presione [MENU] dos veces para llamar el menú Para empezar
principal. (Si usted ha ajustado ya el reloj, usted Conecte la alimentación del TV, amplificador y
sólo tiene que presionarlo una vez).
cualquier otro componente que se encuentre conectado
al DVD/VCR. (Cambie el sistema de entrada para que
se adapte DVD/VCR y compruebe que el volumen de
sonido sea correcto).
¡
Si el reloj no está ajustado, aparece primero el menú
CLOCK SET. En este caso, siga el paso [3].
2
3
Seleccione “CLOCK SET” presionando [PLAY]o
[STOP]. Luego, presione [F.FWD]
1
Presione el Botón POWER.
¡La alimentación se conectará.
Ajuste el reloj.
Compruebe que la Luz DVD OUTPUT está encen-
dida. Si no, presione el Botón DVD en el control
remote para cambiar el modo DVD/VCR.
1) Ajuste el mes
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
2
Presione el Botón OPEN/CLOSE.
¡La bandeja de carga del disco se abrirá.
2) Ajuste el día
3
Ponga un disco en la bandeja.
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
¡Asegúrese de que el disco está asentado correcta-
mente, con el lado de la etiqueta arriba.
3) Ajuste el año
4
Presione el Botón PLAY.
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
¡La bandeja se cerrará automáticamente, y la repro-
ducción empezará luego desde el primer capítulo o
pista del disco. Usted necesita presionar el Botón
PLAY sólo cuando la bandeja se ha cerrado presion-
ando el Botón OPEN/CLOSE.
El día de la semana aparecerá automáticamente.
4) Ajuste la hora
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
5
Presione el Botón STOP para detener la
reproducción.
5) Ajuste el minuto
Presione [PLAY] o [STOP] repetidamente
Luego, presione [F.FWD].
6) Ajuste el AM o PM
AJUSTE DE RELOJ
MES DIA
AÑO
Presione [PLAY] o [STOP]
repetidamente.
03 18 LUN 2002
/
HORA MINUTO AM/PM
05
:
40
PM AM
PM
¡Para retroceder un paso, presione [REW]
4
Ponga en marcha el reloj presionando
[CLEAR/C.RESET] o [F.FWD].
SP
–
–
47
1L25
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to
any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE
UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,
please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-968-3429
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0VMN03028
#####
H9225UD
Download from Www.Somanuals.com. All Manuals Search And Download.
|