swisherinc.com
OWNER’S
MANUAL
MODEL NO.
POLB10544HD
RTB105441
RTB1254412V
44” ROUGH CUT
TRAILMOWER
Assembly
Operation
Service and Adjustment
Repair Parts
Rev. 05-301
1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093
PHONE (660) 747-8183 FAX (660) 747-8650
Made In The
Manufacturing quality lawn care equipment since 1945
USA
ONRT44
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for choosing Swisher’s RC44 Trail mower. Before operating
your mower, please read, understand and follow all of the safety
precautions and other instructions explained in this manual . As with all
power equipment, lawnmowers can be potentially dangerous if improperly
used.
SAFETY PRECAUTIONS
This Safety Alert Symbol indicates important messages in this
manual. When you see this symbol, carefully read the message that
follows and be alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands and feet, and
throw objects. Failure to observe the following safety instructions could result in
serious injury or death.
•
•
Read the manual. Learn to operate this machine safely.
Always disconnect the spark plug wire and place the wire where it cannot contact the
spark plug, to prevent accidental starting the engine when setting up, transporting,
adjusting or making repairs.
•
•
Keep all shields and guards in place.
Understand the speed, steering and stability of this machine. Know the positions and
operations of all controls before you operate this machine. Check all of the controls in
a safe area before starting to work with this machine.
•
•
•
Allow only responsible adults who are familiar with these instructions to operate this
machine. Never allow children to operate this machine.
Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and
thrown by the blade.
Be sure the area is clear of other people before mowing. Be aware of the mower
discharge direction and do not point at anyone. Stop the machine if anyone enters the
mowing area. Children are often attracted to the machine and the mowing activity.
Never assume that children will remain where you last saw them. Keep children
under the watchful care of another responsible adult.
•
•
•
No riders!
Do not put hands or feet near or under rotating parts.
Do not mow in reverse. Always look down and behind before and during backing.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Turn off the blades when not mowing. Before leaving the machine, turn off the blades
and stop the engine.
•
•
Watch for traffic when operating near or crossing roadways.
Do not operate the mower if it has been dropped or damaged in any manner or if the
mower vibrates excessively. Excessive vibration is an indication of damage.
Repair mower as necessary.
•
Dress properly. Do not operate the mower when barefoot or wearing open sandals.
Wear only solid shoes with good traction when mowing.
•
•
•
•
•
Never allow operation by untrained persons.
Do not operate the machine while under the influence of alcohol or drugs.
Do not operate on slopes greater than 15 degrees.
Never tamper with safety devices. Check their proper operation regularly.
Stop and inspect the equipment if you strike an object. Repair, if necessary, before
restarting. Never make adjustments or repairs with the engine running.
Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra
caution when servicing them. Do not operate at too fast a rate.
Return lever to its vertical position to disengage blades.
The braking system is applied when the blades become disengaged. It is designed to
bring the blades to a quick stop (approximately 7 seconds). Each Trail Mower brake
system has been tested and calibrated. For safety, the consumer should not alter the
braking system.
•
•
•
ASSEMBLY
•
•
•
Disengage spark plug wire and place where it cannot make a connection.
(Refer to Owner’s Manual p.11) Attach receiver hitch parts to P/N 4866TC.
Check engine oil. All engines are filled with oil at the factory. Verify oil level and
add if necessary before starting engine. (See Engine Owner’s Manual)
Verify fuel level and add if necessary before starting engine.
Check the battery (if so equipped). If battery is put into service after the “month & year” of the
date on the battery, then it may need to be charged with a 12 volt battery charger for a minimum
of 1 hour, but no more than 2 hours at a rate of 6 to 10 amps.
•
•
•
Attach battery cable(s) to battery. Red wire to positive (FIRST) and black wire to negative
(SECOND).
•
•
Reconnect spark plug wire.
(Refer to Owner’s Manual p. 5) For proper operating procedures.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING YOUR TRAILMOWER
The operation of any mower can produce foreign objects to be thrown into the
eyes, resulting in severe eye damage. Always wear certified safety glasses or
wide-vision safety goggles over spectacles before staring any cutting machine and
while operating such a machine.
The operation of any cutter produces sound waves that are damaging to the
human ear. Ear protection is recommended.
CAUTION!
Tragic accidents can occur if the operator is not alert to the presence of
children. Children are often attracted to the machine and the mowing
activity. Never assume that children will remain where you last saw them.
INTENDED USE
The 44” Rugged Cut Trail Mower is designed to clear dense areas of grass and cut
saplings up to 1 inch thick on golf courses and small estates. It is not intended to create a
finish cut on lawns.Your Trail Mower should be towed behind an ATV, golf cart, lawn
tractor, or other approved vehicle. It is not recommended for speeds exceeding 5 MPH.
ATTACHING TRAILMOWER TO TOW VEHICLE
•
•
Back vehicle up to desired towing position.
Offset the Trail Mower to the side opposite the tow vehicle discharge (if any).
This prevents the tow vehicle from throwing grass into Trail Mower engine.
Bolt swivel hitch (H10) to vehicle tow receiver. If tow vehicle has a ball
hitch, the ball must be removed before swivel hitch can be fastened.
Attach tow hitch and the “L” hitch (4866 & H1) to the swivel hitch. The hitch
pin (H11) should go completely through both the swivel and “L” hitches and
clipped to prevent accidental separation. Check that all hardware is secure at
both the tow vehicle and the Trail Mower.
•
•
TRANSPORTING MOWER
•
•
•
Stop Trail Mower.
Place Trail Mower deck in its highest position.
When transporting unattached from tow vehicle, remove spark plug wire and
place it where it cannot contact the spark plug.
ENGAGING BLADES
Note: Do not start the mower with the T-handle console is in the “ENGAGED” position.
•
Engage blades by pulling T-handle lever into its horizontal position.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Return lever to its vertical position to disengage blades.
The braking system is applied when the blades become disengaged. It is designed
to bring the blades to quick stop (approximately 7 seconds). Each Trail Mower
brake system has been tested. For safety, the consumer should not alter the braking
system.
STOPPING THE ENGINE
•
•
•
•
Make sure the tow vehicle parking brake is set.
Disengage mower blades.
Reduce engine idle speed, and allow engine to run momentarily for cooling.
Turn key to the “OFF” position.
STARTING THE ENGINE
See engine manufacturer’s recommendations for the type and amount of oil and fuel used.
•
Make sure the tow vehicle parking brake is set, mower is level, and blades are
disengaged. Engine must be level to accurately check and fill oil. Do not overfill.
Check spark plug wire, oil, and fuel.
Check all electrical connections for build-up of debris.
Set engine idle to “CHOKE” position.
Turn key to the “RUN” position.
Pull rope with a single fluid motion.
(12V models only) Turn key to the “RUN” position, then to the “START” position.
Set engine idle at maximum RPM for best performance.
Allow engine to run a few moments before engaging blades.
•
•
•
•
•
•
•
•
BREAKING IN YOUR MOWER
•
•
•
Set the vehicle parking brake and chock the wheels to prevent accidental rolling.
While the engine is running, slowly, engage blade control.
In a safe environment, i.e. no children or pets, allow blades to rotate and engine to
idle for 5 minutes, breaking-in the belt for a longer life.
Stop mower.
•
CAUTION: SHUT OFF THE MOWER ENGINE AND REMOVE SPARK
PLUG WIRE FROM SPARK PLUG BEFORE MAKING ANY
ADJUSTMENTS TO THE MOWER.
FRONT TO BACK ADJUSTMENT
For best cutting results, the mowing deck should be parallel to the ground. To check parallel
adjustment, measure the distance from the bottom edge of the deck in both the front and rear of
the deck. This adjustment is best done while the tow vehicle and Trail Mower are connected.
•
•
•
Remove bolts and nuts from the “L” hitch (H1).
Raise or lower hitch section to obtain proper front to back adjustment.
Connect bolts and nuts in “L” hitch securely.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MOWER HEIGHT ADJUSTMENT
•
•
There is approximately 3 inches of height adjustment.
Rotate height adjust crank handle in a clockwise direction to lift the mower deck. A
counter-clockwise direction is used to lower the mower deck.
Dense areas of grass should be cut twice.
•
•
Push handle down to lock height position.
TOW HITCH OFFSET
•
When offsetting the mower do so to the side opposite the discharge of the tow
vehicle.
•
Swisher recommends if the tow vehicle is equipped with a mid-mount mower to
overlap the cut approximately 6”. This may vary depending on mowing terrain,
obstacles, and/or tow vehicle. Always keep safety the first priority.
Always keep the tow vehicle cutter raised higher than the Trail Mower.
•
STARTING TO MOW
•
•
•
•
•
Adjust the cutting height.
Double check vehicle to mower attachment.
Start mower engine and set throttle to “FAST” for best cutting performance.
Slowly engage T-handle lever.
Carefully mount vehicle and start mowing at a slow travel speed.
STOPPING THE MOWING SESSION
•
•
•
Bring tow vehicle to a complete stop, set the parking brake and disengage blades.
Turn key switch to the “OFF” position.
Always remember to remove keys to avoid irresponsible usage.
SUGGESTED MOWING PRACTICES
•
Operate mower engine at full throttle to assure the best cutting performance and
maximum material discharge.
•
•
Allow wet grass to dry. Wet grass will clump and collect under the mowing deck.
Mowing should be started with tow vehicle in low gear and increased only as safe
mowing conditions permit. Mowing speed should not exceed 5 MPH.
Mowing conditions and the types of grass will vary from place to place. You may
find when mowing dense areas that the pressure of the wheel tracks may cause the
grass to be pushed down and not effectively mowed. If this happens you may want
to mow the area twice. Once with the mower raised and the second mowing at the
desired height. The second mowing should be at a right angle from the previous for
best results.
•
•
•
Reducing the travel speed will help mow dense growth. This allows the blades the
time necessary to make its initial cut, and regain momentum to continue cutting and
discharging debris properly. The engine may stall if you are mowing too fast!
Do not attempt to mow areas that the tow vehicle cannot maneuver through and/or
slopes that you do not feel comfortable riding.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER MAINTENANCE
GENERAL RECOMMENDATIONS
The warranty on this cutter does not cover items that have been subjected to operator
abuse or negligence. To receive full value from the warranty, operator must maintain
unit as instructed in this manual.
Some adjustments will need to be made periodically to maintain your unit properly.
All adjustments in the service and adjustments section of this manual should be checked
at least once each season.
BEFORE EACH SEASON
A new spark plug and clean air filter assure proper air-fuel mixture and help your engine
run better and last longer.
•
•
•
Replace the spark plug.
Clean or replace the air filter.
Check blades and belts for wear.
BEFORE EACH USE
•
•
•
•
Check engine oil level. (Do this twice to ensure an accurate reading.)
Check condition of air filter and clean or replace if necessary.
Check blade operation.
Check for loose fasteners.
DAILY MAINTENANCE
Make sure all nuts and bolts are tight and cotter pins and retainer springs are secure.
Keep blades sharp. Observe all safety precautions.
BLADE CARE AND SERVICE
For best results cutter blades must be kept sharp. The blades can be sharpened with a
few strokes of a file or grinding wheel. Do Not attempt to sharpen while on the cutter.
Important: Replace blades that have been damaged or deeply nicked.
Important: Check blade and spindle hardware on a regular basis to make sure nuts
are tight.
CAUTION: DO NOT HANDLE MOWER BLADES WITH BARE HANDS.
CARELESS OR IMPROPER HANDLING MAY RESULT IN SERIOUS
INJURY.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL TROUBLESHOOTING
The mower is not cutting level.
•
Level deck. Check air pressure of all tires; make sure they are equal. See
tires for maximum inflation.
•
Make certain blades are installed identical, without the engine running.
The engine will not start.
•
Disengage blades, turn key switch to the “OFF” position, check battery and
all other electrical connections, and inspect spark plug and wire.
Contact engine manufacturer or qualified mechanic.
•
Engine runs poorly.
•
•
•
•
See engine manual.
Check the throttle adjuster.
Replace fuel, clean fuel filter and fuel line.
Check spark plug and gap.
Mower bounces excessively while towing.
•
•
Lower tire pressure.
Tow at a lower speed.
IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE
THE MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT
YOU ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER
PROBLEMS.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY AND OPERATIONAL DECALS
Replace decal immediately if damaged. Order by part number from
Swisher Mower and Machine Co. Inc.
OD39-SWISHER FLAG DECAL
OD82-44 RUGGED CUT DECAL
OD33-5MPH DECAL
OD29-DANGER DECAL
OD36-Deflector Decal
OD55-DANGER DECAL
OD10-ENGAGE DECAL
OD45-WARNING DECAL
OD99-OFF/RUN DECAL
OD28-OFF/RUN/START DECAL
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT SKIRT ASSEMBLY
FIGURE 1
5
4
Item #
Description
Part #
NB501
4853TC
4843
NB181
4865TC
1
2
3
4
5
5/16-18 X 1 HCC GR5 ZP
Metal Strap For Rubber Flap
Rubber Flapper, 5" X 42.75"
5/16-18 Nyloc Nut
3
2
Deck Weldment
1
4
5
9
COVER ASSEMBLY
FIGURE 2
3
Item #
Description
Front Auxiliary Pulley Cover
Motor Base Support
Part #
4862TC
1
2
3
4
5
6
7
8
9
9
4836TC
2
4844TC
4844C
Pulley Cover
4840TC
Rear Auxiliary Pulley Cover
5/16-18 X 3/4 Serr Flg Bolt
5/16-18 Serrated Flange Nut
5/16-18 X 1/2 Serr. Flg Bolt
Tinnerman Clips 5/16-18 Heavy Duty
Tinnerman Clip 5/16-18
5
NB596
NB170
NB252
3669
5
7
8
1
3706
5
5
6
8
HITCH BAR ASSEMBLY
FIGURE 3
1
Item #
1
2
3
4
5
6
7
8
Description
Height Adjustment Bar
3/8-16 X 2 1/2 HCC GR5 ZP
1/2-13 Nyloc Nut
1/2-13 Nut GR2 ZP
1/2-13 X 1 1/2 HTC GR2 ZP
3/8-16 Nyloc Nut
Front Torsion Bar
Height Adjustment Bracket Front
1 1/4ID X 1 7/8OD 10 Ga. Washer NB185Z
Part #
4864TC
NB221
NB281
NB213Z
NB617
NB182
4861TC
4805TC
1
2
7
3
4
5
9
10
11
12
13
14
15
16
18
20
21
1/8 X 2 Cotter Pin
3/8-24 X 1 Bolt
3/8-24 Two Way Locknut
Hitch
5/16-18 X 2 1/2 HCC GR5 ZP
5/16-18 Nyloc Nut
Safety Hitch Pin
Hitch Swivel
NB633
NB238
NB216
4866TC
NB138
NB181
H11
H10TK
H1TK
10063
8
9
13
21
6
5
15
4
16
10
3
12
14
L Hitch
Plug for H1
11
20
18
When ordering replacement parts
* = USE PAINT CODE:
TC=TEX.RED,S=SLIVER,TK=TEX.BLACK
11
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
4
3
REAR AXLE ASSEMBLY
FIGURE 4
5
Item #
1
Description
Plastic Knob - Black
Part #
4857
6
19
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
3/8-16 2-Way Lock Nut
Height Adjustment Crank
3/8-16 X 1 1/4 GR5 ZP
1/4-20 X 1 1/2 HCCGR2ZP
1/4-20 Nylok Nut
3/4-10 X 13 Stud w/ Groove
Top Height Adjustment Bar
Height Adjustment Pin Lock
5/16-18 Serrated Flange Nut
5/16-18 X 3/4 Serr Flg Bolt
Bottom Height Adjustment Bar
Rear Torsion Bar
NB280
4874TC
NB618
NB104Z
NB180
4829-010
4850TC
4827TC
NB170
NB596
4851TC
4860TC
NB207
T2PB
NB107
NB216
4809LTC
4809RTC
NB238
NB179
NB126
4834
7
8
9
10
9
11
12
26
3/8-16 Nylok Nut Jam
Plastic Bushing
13
17
14
18
15
3/8-16 X 1 1/2 HCC GR5 ZP
3/8-24 Two Way Locknut
Left Rear Height Adj Bracket
Right Rear Height Adj Bracket
3/8-24 X 1 Bolt
16
20
25
3/4 ID X 1 1/4 OD 18 GA Washer
1/8 X 1 Cotter Pin
24
23
21
Wheel, Tire, Bearings
22
13/16 X 1 1/4 X 1/8 Washer
1/2-13 X 7 3/4 Eye Bolt
5/16-18 X 1/2 Serr. Flg Bolt
NB195
10038
NB252
16
BLADE DRIVER ASSEMBLY
FIGURE 5
6
Item #
1
Description
Stump Jumper Weldment
3/4 Washer ZP
Part #
4859TK
NB179
4855
Note: Torque to
235 ft/lbs
2
14
3
15" Blade
4
5
6
7
3/4-10 X 2 1/2 GR8 Bolt
3/4-10 Nyloc Nut
1"ID X 2"OD X 14GA Bellville Washer NB738
1 X 1 1/2 10GA Washer Hardened PLN NB614HT
NB611
NB609
13
12
8
8
9
Blade Bearing
Tube Spacer
Blade Driver
4845
4049
10
11
17 Includes Item#’s
8, 9, and 10
10
11
12
13
14
15
16
17
4858TK
NB509
NB281
BB105SL
4846
NB737
NB612
4872
1/2-13 X 2 HCC GR5 ZP
1/2-13 Nyloc Nut
Spacer
Blade Pulley- 10.3125"
1-8 X 7 1/2" GR8 ZP
1-8 Nyloc Nut ZP
Blade Driver Complete
9
8
5
7
1
2
3
4
When ordering replacement parts
* = USE PAINT CODE:
6
TC=TEX.RED,S=SLIVER,TK=TEX.BLACK
15
12
Download from Www.Somanuals.com. All Manuals Search And Download.
NOT ACTUAL
ENGINE USED
(REF. ONLY)
ENGINE PULLEY ASSEMBLY
FIGURE 6
Item #
Description
Engine B&S Recoil St W/Gas Tank
Engine B&S 12V St W/Gas Tank
5/16-18 Serrated Flange Nut
5/16-18 X 1 1/4 Serrated Flange Bolt
5/16 USS Flat Washer ZP
RT44 Belt Guide
Part #
N/A
1
1
N/A
2
3
4
NB170
NB253
NB556
4867
5
6
7
8
9
Spacer For Engine Pulley
5/16-18 X 2 1/4 Flang Serr. GR5 ZP
Engine Pulley- 4.25"OD,1 1/4 ID
1/4 X 1 Key Stock
BB105S
NB622
BB105
9031
14
10
11
12
13
14
15
Spacer Lower For Engine Pulley
Washer
Washer Belleville Engine Pulley
7/16-20 X 1 HCF GR5 ZP
Oil Drain Valve
BB105SL
TR150W
699
NB452N
AS122
AS123
3
2
2
5
4
6
4
7
Oil Drain Cap
15
8
10
12
9
11
13
BELT ENGAGE CONFIGURATION
FIGURE 7
29
Item #
1
2
Description
1/2-13 X 2 1/2 HCC GR5 ZP
Idler Arm
Part #
NB510
6681TK
NB121
NB180
NB250
9023
4898TK
NB102
NB274
NB519
NB181
B99S
NB196
NB501
NB281
699
4893
NB220
9040
28
3
4
1/2-13 2-Way Jam Lock Nut
1/4-20 Nylok Nut
1
20
5
6
7
1/4-20 X 3/4 GR5 ZP
Clutch Cable Clevis
Belt Engage Arm
27
10
9
2
8
9
1/4-20 X 1 HCC GR5 ZP
1/4 SAE Washer
10
11
12
13
14
15
16
17
20
21
22
23
24
25
26
27
28
29
5/64 X 3/4 Cotter Pin
5/16-18 Nyloc Nut
26
21
25
Spacer
3
3/8 Hardened Washer
5/16-18 X 1 HCC GR5 ZP
1/2-13 Nyloc Nut
4
17
5
Washer Belleville
Brake Arm Assembly
1/2 X 1-9/16 Shoulder Bolt
Torsion Brake Spring
Brake Rod
13
16
24
23
22
4891TK
NB139
682S
NB619
NB212
B527
1/4-20 HX Nut ZP
Clutch Rod Spring
3/8-16 X 2 1/2 HTC GR5 ZP
3/8-16 HNC GR2 ZP
Idler Pulley OD-3.25", ID-3/8"
3/8 SAE Washer
6
15
4
7
14
13
NB272
NB182
9
8
3/8-16 Nyloc Nut
12
10
11
When ordering replacement parts
* = USE PAINT CODE:
TC=TEX.RED,S=SLIVER,TK=TEX.BLACK
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE ASSEMBLY
FIGURE 8
Item #
Description
T Handle for Console
1/4-20 Nylok Nut
Part #
4463TK
NB180
NB181
NB591
4575TK
9088
9087
KSM
3623
16
15
10
13
1
2
3
4
5
6
7
8
17
10
1
5/16-18 Nyloc Nut
5/16-18 X 1 1/2 Torx Pan ZP
Console Weldment
Key Switch Lock Washer
Key Switch Nut
2
14
Key Switch ON-OFF, 2 Prong
Key Switch
18
3
5
12
10
9
1/4-20 X 2 1/2 HCC GR2 ZP
1/4 SAE Washer
NB141
NB274
4852TK
NB608
NB518
NB560
9023MOD
4461TK
NB597
WHRT44BS
4
10
11
12
13
14
15
16
17
18
Console Mount Plate
1/4-20 Wing Nut ZP
1/4 X 1 1/2 Clevis Pin
1/4-20 X 1 1/4 HCC GR5 ZP
Clutch Cable Clevis
Link for Console
3/32 X 3/4 Cotter Pin
Wiring Harness B&S
Wiring Harness Console (12V) WHRT44-1
6
11
7
8
10
9
P/N 4846
P/N B527
P/N BA 50
P/N BB105
WIRING DIAGRAM
FIGURE 10
When ordering replacement parts
* = USE PAINT CODE:
TC=TEX.RED,S=SLIVER,TK=TEX.BLACK
ENGINE PULLEY CONFIGURATION
FIGURE 9
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Rough Cut 44 12 Volt Start Replacement Parts
SEE FIGURE 8
1
2
3
Item #
1
2
Description
Battery Bracket Weldment
5/16-18 X 3/4 Serr Flg Bolt
5/16-18 Serrated Flange Nut
M6-1.0 Nut Yellow Zinc
Part #
4909TK
NB596
NB170
NB600
9043
BHOLD
BCS
BCSR
BCBT
11764
3
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Solenoid Assembly
Battery Hold Down, 15" Tarp Strap
Battery Cable (Black 10")
Battery Cable (10" Red)
Battery Cable Small Rubber Boot
Lower Wiring Harness
Battery Pad
BATPAD
WIRING DIAGRAM
FIGURE 11
When ordering replacement parts
* = USE PAINT CODE:
TC=TEX.RED,S=SLIVER,TK=TEX.BLACK
15
Download from Www.Somanuals.com. All Manuals Search And Download.
44”ROUGH CUT
TRAILMOWER
swisherinc.com
Each mower has its own model number. Each engine has its
own model number. The model number for the mower will be
found on the right hand side of the motor mount. The model
number for the engine will be found on the top of the blower
fan housing.
All mower parts listed herein may be ordered directly from
Swisher Mower & Machine Co. Inc. or your nearest Swisher
dealer.
OWNER’S
MANUAL
All engine parts may be ordered from the nearest dealer of the
engine supplied with your mower.
MODEL NO.
POLB10544HD
RTB105441
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT - TRAILMOWER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
RTB1254412V
* PART NUMBER
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE P.O. BOX 67
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO. INC.
PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|