Cinema Grand
Signature 400 ~ seven
and 200 ~ seven
Cin
em
a
Gran
d
Power
S
upply
Ener
gy
2
0
0
0
3
0
0
0
1
4
0
0
0
5
0
0
JOULES
L
o
a
d
I
n
v
a
ria
n
t H
ig
h
F
id
elity
S
u
p
er
D
efin
itio
n
P
o
w
er
A
m
p
lifie
r
S
ig
n
a
tu
re
per
4
0
0
~
s
Four Hundr
ed
e
v
en
Wa
tts
Channel
b
y
Seven
C
hannels
Su
n
fir
e
seven
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
15. To prevent electric shock, do not 16. Grounding or Polarization —
ATTENTION — Le présent appar-
eil numérique n'émet pas de bruits
radioélectriques dépassant las limites
applicables aux appareils numériques
de class A/de class B (selon le cas)
prescrites dans le règlement sur le
brouillage radioélectrique édicté par
les ministere des communications du
Canada.
use this polarized plug with an exten-
sion cord, receptacle or other outlet
unless the blades can be fully inserted
to prevent blade exposure.
Pour préevenir les chocs électriques
ne pas utiliser cette Þche polariseé
avec un prolongateur, un prise de
courant ou une autre sortie de cou-
rant, sauf si les lames peuvent être
insérées à fond sans laisser aucune
parIIIe à découvert.
Precautions should be taken so that
the grounding or polarization means
of the Component is not defeated.
This apparatus does not exceed the
Class A/Class B (whichever is ap-
plicable) limits for radio noise emissions
from digital apparatus as set out in the
radio interference regulations of the Ca-
nadian Department of Communications.
WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRO-
DUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Contents
Please read the Safety Instructions
Safety Instructions................................... 2-3
carefully before connecting and
using your SunÞre AmpliÞer.
Chapter 1: Introduction ...............................4
Cinema Grand Editions ..............................5
Unpacking and Installation .........................6
Front Panel Features..................................7
Rear Panel Features ..................................8
Chapter 1 is a general introduction
to the features, details and installa-
tion of your ampliÞer.
Chapter 2 shows some typical con-
nections to a preampliÞer and
speakers.
Chapter 2: System ConÞgurations...........10
The Appendix shows some addition-
al information, including a trouble-
shooting guide, the Warranty, and
service assistance details.
Appendix:
Series and Parallel ...................................15
Troubleshooting Guide .............................16
SpeciÞcations ...........................................18
Limited Warranty ......................................19
Service Assistance ...................................19
To Þnd out more about this and other
SunÞre products, please visit our
3
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Introduction
Bob Carver, AmpliÞer Designer, Physicist
Dear Friend,
Thank you for purchasing my SunÞre Cinema Grand seven channel power ampliÞer. I hope you en-
joy it and the music it makes as much as I have enjoyed creating it for you.
This magniÞcent ampliÞer represents my very latest thinking - and my best ampliÞer design ever.
I’ve spent over twenty years developing it, and cannot imagine how I could make it any better, or
reÞne it any further. No matter what, its performance is, at Þrst, somewhat difÞcult to believe.
The Signature 400~seven can produce 400 watts rms per channel into 8 ohms and 800 watts
rms into 4 ohms.
The 200~seven can produce 200 watts rms per channel into 8 ohms, and 400 watts rms into 4
ohms.
The big breakthrough feature of the Cinema Grand is its uncanny tracking downconverter, which
uses 18 Herculean Mosfets in the Signature 400~seven and 12 in the 200~seven. This allows the
Cinema Grand to produce phenominal power output, without the heat generated by conventional
designs.
The circuit boards are heavy glass epoxy, double sided, with a Faraday shield on the back side.
All resistors in the signal path are 1% tolerance, metal-Þlm. Critical capacitors are Þlm devices with
high dielectric strength and ultra low absorption characteristics. An enormous Cinema Grand power
source built around a massive power transformer provides the ultimate muscle for limitless dynamics.
I could go on and on, but here’s the best part: I’ve included two kinds of outputs on the front left
and front right channels:
(1) a standard voltage-source (i.e., near zero impedance) output for all typical applications and:
(2) a higher-impedance current-source output, which many prefer for electrostatic, planar
magnetic, or ribbon speakers. Or you can biwire your system with the voltage source driving
the woofer(s) and the current source driving the upper part of the system. In many cases this
provides by far the best possible interface between the ampliÞer and the speaker system.
Whichever way you decide to hook up the SunÞre Cinema Grand, it will create a multilayered
soundstage that is deep, wide, three-dimensional, and utterly believable. The optional current-source
output can coax forth a sensuous, delicately detailed musical voice long associated with low-powered
classic tube ampliÞers. (The current-source characteristic of vacuum tubes is the dominant factor in
the soundstage delivery of classic tube ampliÞers).
4
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Cinema Grand Editions
The Cinema Grand seven chan-
nel power ampliÞer is available in two
editions:
Signature 400~seven
400 Watts per channel into 8 Ω
800 Watts per channel into 4 Ω
•
•
Signature 400~seven
200~seven
Cinema Grand
Power Supply Energy
The Signature 400~seven has twice
the power output, and uses heavier
output terminals compared to the
200~seven. Each Signature 400~sev-
en is personally signed on the front
panel by Bob Carver.
JOULES
Load Invariant High Fidelity Super Definition Power Amplifier
Signature 400 ~ seven
Four Hundred Watts per Channel by Seven Channels
Sunfire
This manual uses illustrations of the
Signature 400~seven. The operational
details, features, and connections to
loudspeakers and preampliÞers are
the same for both models.
200~seven
200 Watts per channel into 8 Ω
400 Watts per channel into 4 Ω
Cinema Grand
Power Supply Energy
JOULES
Load Invariant High Fidelity Super Definition Power Amplifier
200 ~ seven
Four Hundred Watts per Channel by Seven Channels
Sunfire
5
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Unpacking
Installation
Your SunÞre AmpliÞer should reach
you in perfect condition. If you do
notice any shipping damage, please
contact your SunÞre Dealer immedi-
ately.
Read and follow all safety instruc-
tions shown on pages 2 and 3.
•
Make sure that the power
cords of all your components
are attached to the same outlet
or at least to the same circuit.
This will reduce the possibility
of a ground loop in the system.
Observe the following precautions
when choosing a location for your
Cinema Grand AmpliÞer:
Gently lift out the unit and remove
all the packing material and acces-
sories. It is important to save all the
packing materials and the box in case
your ampliÞer ever needs to be moved
or shipped for repair.
•
•
Protect it from prolonged
exposure to direct sunlight and
other direct sources of heat,
such as heating vents and
radiators.
Make sure that the total cur-
rent draw does not exceed
the current rating of your AC
outlet or power strip.
•
•
Use the XLR inputs if your
preampliÞer has XLR outputs.
These balanced connections
provide superior noise rejec-
tion.
Do not expose the unit to rain
or moisture. If ßuid or a for-
eign object should enter the
unit, immediately turn off the
power and contact your SunÞre
Dealer.
Make sure that you keep your sales
receipt. It is the only way to establish
the duration of your Limited Warranty
and it may come in useful for insur-
ance purposes.
Whenever possible, keep the
power cords away from the
signal cables or speaker wires
to prevent any hum or audio
interference being heard in the
speakers.
Please take a moment to Þll out and
mail the SunÞre Customer Response
card. Also read the serial number
located on the rear panel or the under-
side of the chassis, and record it here:
•
•
•
Avoid excessive exposure to
extreme cold or dust.
Do not place heavy objects on
top of the unit.
•
•
Choose reliable hookup cables,
also called patch cords or RCA
cables. They should be fully
shielded and as short as pos-
sible for the job.
Allow adequate ventilation
around the ampliÞer; do not
cover the ventilation slots.
Serial #:
___________________________
Purchased at:
AC Power Considerations
Ensure that the unit is plugged into
an outlet capable of supplying the cor-
rect voltage speciÞed for your model.
The outlet should be capable of sup-
plying 15 amps for the 120 V model,
8 amps for the 230 V model.
Some patch cords can be a
very tight Þt and there is usu-
ally a preferred method of get-
ting them off. Some have to be
removed with a twisting action.
Be gentle or you may damage
the jacks of the ampliÞer or
your other components.
___________________________
___________________________
___________________________
___________________________
Date: _______________________
Care
If you need to clean the front sur-
face, Þrst turn off the power and then
use a dry soft cloth, rubbing with the
grain. Be careful not to scratch the
display window.
•
•
Some special patch cords
can only be hooked up in one
direction, these are usually
marked with arrows.
It is usual for the right patch
cord plugs to be red and the
left connections to be white,
grey or black. Video connec-
tions are usually yellow.
Connection Tips
Before setting up your new system,
please consider the following :
Always make sure that your
components are all turned
OFF before making or
changing connections.
6
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Front Panel Features
Cinema Grand
Power Supply Energy
JOULES
Load Invariant High Fidelity Super Definition Power Amplifier
Signature 400 ~ seven
Four Hundred Watts per Channel by Seven Channels
Sunfire
Overview
Meter
Illumination
Your Cinema Grand AmpliÞer has
seven channels of power ampliÞca-
tion combined in one chassis for the
The front panel meter indicates the
total energy available from the track-
ing downconverter power supply. It is
The meter is illuminated by an
incandescent lamp operating at a
very warm color temperature. I have
been inßuenced by the scale lighting
of classic electronic equipment from
the 1950’s, with their warm dim glow,
usually with a “headlight effect” from
the lamp. I incorporated that historical
look and feel into this meter lighting. It
is decidedly not “evenly back-lit,” nor
with a cool to cold color temperature. I
hope you like my unusual meter light-
ing treatment.
purpose of reproducing music or video calibrated in Joules and will normally
soundtracks. It accepts line level
signals from a controlling preampliÞer
and ampliÞes them to a higher level,
suitable for driving powerful stereo
and Home Theater speakers.
indicate approximately 480 Joules
for the Signature 400~seven, and
400 Joules for the 200~seven. Note
that the needle does not move under
normal use.
Crystal Base
The glass base is intended to en-
sure proper airßow under the ampli-
Þer. It prevents any carpeting from
restricting the airßow.
A switch has been provided on the
underside of the unit toward the front.
This switch gives you the ability to
dim the meter lamp to reduce distrac-
tions in a Home Theater environment.
I like the brighter of the two settings,
as it illuminates the meter nicely and
matches my other SunÞre equipment.
Feel free to choose the setting that
suits you.
If you choose to place the unit on a
shelf or other hard surface, the base
will isolate the amp from vibration and
will help make an attractive installa-
tion.
7
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Rear Panel Features
1 2
3 4
5
6
6
5
6
7 6
6
6 7 6
8 9
The voltage range for the trigger
input is from 5 to 18 VDC. The input
impedance is approximately 600 Ω
(20 mA @ 12V).
1. AUTO/ON/OFF Switch
Your Cinema Grand AmpliÞer is
designed with an automatic on/off
circuit.
2. 12 VDC Trigger Input
Although the AUTO-ON signal
sensing turn-on is adequate for most
installations, the 12 VDC trigger inputs
are offered as an optional way to turn
on the ampliÞer.
3. RCA Inputs
•
In the AUTO-ON position, the
ampliÞer will automatically turn
on if an audio signal is pres-
ent at any of the inputs, or if it
receives a 12 VDC input volt-
age at the trigger inputs. The
ampliÞer will automatically turn
off after a few seconds if the
trigger voltage is removed, or
after approximately 30 minutes
in the absence of an audio
signal.
Your Cinema Grand AmpliÞer has
three sets of inputs for each of the
seven channels. Two are unbalanced
RCA inputs and one is a balanced
XLR type.
The SunÞre Theater Grand II, III
and IV Processors have a compatible
12 VDC trigger output (see page 11).
This can be used to automatically turn
on the Cinema Grand when the The-
ater Grand Processor is turned on.
The two RCA inputs for each chan-
nel are joined together internally, and
either one can be connected to the
corresponding output of your pream-
pliÞer.
1/8" mono mini jacks are provided
for ease of installation, along with a
terminal strip to allow more ßexibility
for custom-wired installations. The
terminal strip and both mini jacks are
internally connected in parallel, allow-
The second RCA input can be used
as a daisy-chaining output, sending
the preampliÞer output signal to an-
other channel or to another ampliÞer.
•
•
In the ON position, the ampli-
Þer is always on, regardless of
input signals or 12 VDC trigger. ing 'daisy chaining' to turn on multiple
ampliÞers.
In the OFF position, the ampli-
Þer is always off, regardless of
Any 1/8" miniplug mono or stereo
input signals or 12 VDC trigger. interconnect cable will sufÞce to con-
nect the trigger output of the Theater
Grand preamplifer to the ampliÞer.
Do not exceed 18 VDC on
this input. (CAUTION: Do
not connect AC line voltage
to this input!)
8
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
NOTE: The Current Source output
is a Voltage Source modiÞed to yield
an impedance of one ohm. This cor-
responds approximately to a vacuum
tube ampliÞer's output impedance and
constitutes the dominant factor in the
soundstage delivery of classic vacuum
tube power ampliÞers.
4. XLR Inputs
5. Current Source Outputs
and:
6. Voltage Source Outputs
The front left and front right chan-
nels each have a Voltage Source
output and a Current Source output.
The remaining channels have Voltage
Source outputs only.
If your preampliÞer has XLR
outputs, connect them to these XLR
inputs. These balanced connections
offer superior noise rejection com-
pared to the unbalanced RCA inputs.
The female XLR inputs are wired
as follows:
7. Current Source Fuses
Pin 1 is ground
Each Current Source output has an
in-line fuse to protect your speakers. If
one ever opens, there will be no out-
put to that speaker. Turn off the power
if you ever have to change a fuse.
The Voltage Source outputs have
a source impedance of approximately
zero ohms. The Current Source
outputs have a source impedance of
approximately one ohm.
Pin 2 is positive (hot)
Pin 3 is negative (cold)
Balanced connections pass the
input signal along two conductors. If
there is any external noise and inter-
ference passing into the audio lines,
both conductors will receive the same
amount of noise. This noise is then
rejected in the balanced input stage of
the Cinema Grand AmpliÞer.
The top post of each binding post
pair is the positive output, and con-
nects to the positive (red) post of your
speaker. The bottom post of each pair
is the negative, and connects to the
negative (black) post of your speaker.
The posts can accept bare wire,
spade terminals, and dual or single
banana connectors.
8. IEC connector
The ampliÞer comes with a detach-
able Linecord which attaches here.
Make sure it is Þrmly pushed in place.
Connect the other end to an AC outlet
which is properly conÞgured for the
type of plug and has the correct volt-
age for your model.
9. AC Line fuse
If this fuse fails, replace it with the
exact same type and current rating.
+
-
+
-
Note: Always unplug the
power cord from your AC
outlet before removing the
fuse.
Bare Wire
Spade
With a ßat ended screwdriver, push
the fuse carrier in slightly and turn it
counter-clockwise to release.
+ -
Dual-Banana
Banana
+ -
According to your musical taste,
you may select the Current Source for
driving electrostatic, planar magnetic
or ribbon speakers. Select the Volt-
age Source for driving subwoofers.
For cone based systems, use either.
For a biwired system, use the Current
Source for midrange and treble driv-
ers, and use the Voltage Source for
the subwoofer(s). These are sugges-
tions only. By all means, please feel
free to experiment with other wiring
options. (See page 14.)
9
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
System ConÞgurations
The following pages show some typical connections that you might make in your installation. They show how the inputs
and outputs of the Cinema Grand AmpliÞer are connected to your preampliÞer and speakers.
Unbalanced Connections
UNBA
PREAMP OU
LANCED
TPUT
S
RB
R
RS
C
LS
L
LB
Line-level audio signals
From: PreampliÞer main RCA outputs
To:
AmpliÞer line-level inputs
+
+
+
+
+
RB
+
L
R
+
Speaker-level audio outputs
From: AmpliÞer outputs
To: Speaker input posts
RS
LOUD
C
LS
SPEAKERS
B
L
Make sure that the posi-
tive speaker wires do not
touch the negative speaker
wires, or any chassis metal.
R
C
L
= Right Channel
= Center Channel
= Left Channel
If your preampliÞer has RCA out-
puts, it can be connected to the ampli-
Þer inputs as shown. The ampliÞer will
boost the preampliÞer's output, up to a
level suitable for driving speakers.
RS = Right Surround (rear) Channel
LS = Left Surround (rear) Channel
RB = Right Surround Back Channel
LB = Left Surround Back Channel
This will cause a short circuit and may
damage your ampliÞer or speakers.
This diagram also shows how the
Voltage Source outputs connect to
the input posts of your speakers. (The
Current Source can be used instead,
as shown on the next page).
10
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Balanced Connections
If your preampliÞer has XLR outputs, it can be connected to the XLR inputs as shown. This example shows the connec-
tions to the SunÞre Theater Grand IV processor. This also shows the Current Source output connections to the front left
and right speaker inputs. (The Voltage Source outputs can be used instead, as shown on the previous page.)
SunÞre Theater Grand IV Processor
AUDIO/VIDEO INPUTS
DVD
SAT
S
VID1
VID2
VIDEO
AUDIO/VIDEO OUTPUTS
VC
VC
R
CD
M
A
IN
COMP
DVD
VC
O
NENT VIDEO IN
R
VID2/MON2
FM
COMP
SAT
O
NENT OUT
MON2
VID1
7
I
R
M
A
IN
DVD
DVD
TRIG
SAT
SAT
G
ERS
12VDC
COMP
VIDEO
M
A
IN
VID1
VID1
VID2
VID2
R
BALANCED AUDIO OUTPUTS
CD
CD
Y
M
A
IN
L
VC
R
VID2/MON2
VID2/MON2
L
C
LS
L
12VDC
ZONE2
G
N
12VDC
C
LB
C
r
VC
R
M
A
IN ZONE
L
I
R
M
A
IN
VC
ZONE2
R
RS-232
C
b
RIGHT
DIGITAL
A
U
RIGHUR
R
D
IO IN
VI
PU
TS
SUB
D
VD
RB SU
R
SA
T
D
VD
Made in
D
1
R
R
SA
A
C
D
Snohomish Washington
U.S.A.
U
T
D
RS
IO IN
PH
O
P
VI
U
TS
D
1
N
O
D
A
SW
T
AUDIO OUTP
T
A
PE
UTS
PE
D
A
T
RB
T
8-
C
A
H
L
A
N
S
N
E
L
L
E
IN
PU
FT
T
C
L
S
U
R
D
A
DIGITA
T
C
EN
L
OU
LB
VI
D2
S
T
S
TE
RE
O
XED
IN
U
L
R
O
IE
E
139
FI
UT
E
4
P
UTS
M
A
ZO
N
E2
L
E
F
M
A
S
T
Sunfire Corpo
Theater G
R
IN
A
L
U
E
FT
D
EINO OU
U
R
C
TPU
TS
ration
T
E
R
S
U
B
2
R
L
LB
rand IV
SID
ES
PH
O
SU
R
N
O
D
A
T
L
SI
D
E
A
XI
TA
PE
S
MA
DO
NU
FAC
TUR
D
A
T
ED
NDE
U
R
LI
CE
"D
OLB
-D SY
NS
TA
PE
LB
E
F
"
Y
LA
ROM
B
OR
ATOR
IES
.
A
C
LOGI
Y",
R
IG
C
IN
"
A
PR
O-
H
T
ND
PU
T
R
THE
RKS
OF
DOUB
LE
S
TR
U
R
AD
M
S
E
BOL
MA
ARE
RATORI
R
U
B
DOLBY
LA
BO
R
B
S
MA
DIGI
US
5,9
PA
ES.
FROM
U
NUFA
TAL
PAT.
R
CTU
THE
NO.
RE
ATER
5,451
O
D
U
NDE
FI
XED
R
LIC
EN
SE
INC.
M
A
IN
ZO
N
E2
SYS
TEM
S,
12 VDC Trigger signal
R
IG
,94
H
2, 5,
THE
R
WOR
LD
T
956
,67
4, 5,9
78,
762
74,
380
R
IG
AN
D
,
H
T
S
U
R
-W
IDE
DIN
SU
RROU
TE
NTS
ISS
S
UED
U
AN
D
B
P
1
EN
ED
"DTS
G.
", "D
TS
O:6
TH
-ES
"
E
T
S
EX
U
TE
B
ND
TRA
3
AN
D
DIGI
"NE
TA
ND
"
R
B
A
RE
ATE
1
996
S
U
R
DE
MA
RK
From: PreampliÞer trigger
S
OF
NC.
DIGITA
L
R
SI
D
R
SY
E
ST
EMS
A
XI
S
C
OP
,
I
YR
IGH
,
20
00,
L
THE
AT
ER
12
6
0
VA
H
C
z
0
outputs
To:
AmpliÞer trigger
inputs
R
C
L
RB
RS
LS
LB
Balanced line-level audio signals
From: PreampliÞer XLR outputs
To:
AmpliÞer XLR inputs
+
R
+
RB
+
+
C
+
LS
Speaker-level audio outputs
From: AmpliÞer outputs
RS
LOUDSPEAKERS
+
L
+
LB
To:
Speaker input posts
The 12 VDC trigger connection
shown can be used to turn the ampli-
Þer on when the preampliÞer turns on.
Alternatively, you could use the ampli-
Þer's AUTO-ON switch. The ampliÞer
will then automatically turn on when a
preamp audio signal is received.
11
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Biamping
If your speakers can be biamped,
the Cinema Grand AmpliÞer can be
conÞgured to provide a very powerful
system.
The following connections are
shown in the diagram on the top half
of the next page.
Output connections
•
Connect the ampliÞer’s right
rear output to the right speak-
er’s woofer input terminals.
Connect the ampliÞer’s right
front current source output to
the right speaker’s upper range
input terminals. If you prefer,
you could use the right front
voltage source instead.
Inputs
Tweeter
•
Connect the ampliÞer’s left
rear output to the left speaker’s
woofer input terminals.
Connect the ampliÞer’s left
front current source output to
the left speaker’s upper range
input terminals. If you prefer,
you could use the left front
voltage source instead.
Woofer
A speaker which can be biamped or
biwired will have two sets of binding
posts. Sometimes these posts are
joined with shorting links for normal
operation.
Input connections
Each ampliÞer channel has two
RCA inputs which are connected
together internally.
Make sure that any links are
removed when you want to
biamp or biwire the speak-
ers. If not, this may cause
damage to the ampliÞer.
•
Connect the preamp stereo
output to the front channel
RCA jacks. Then install short
interconnects from the other
unused front RCA jacks across
to the rear channel RCA jacks.
In this way, the front and rear
ampliÞer channels are fed with
the same signal from your
preamp.
Each speaker can be driven by two
ampliÞer channels; one to drive the
woofer and one for the upper range.
You will need to use four ampliÞer
channels to biamp two speakers.
If you use the Cinema Grand Ampli-
Þer for biamping, then a total of Þve
speakers can be connected. You will
need an extra two channel ampliÞer
if you want to run the surround back
speakers in a Home Theater system.
•
Note: you cannot use XLR
cables in, with RCA out, or
RCA in with XLR out. There is
no direct internal connection
between the RCA and XLR
inputs.
12
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Biamping Connections
UNBALANC
E
D
PREAM
P
OUT
PUTS
R
Line-level audio signals
From: PreampliÞer main RCA outputs
To: AmpliÞer RCA inputs
L
Line-level audio signals
From: AmpliÞer Front L/R RCA
To:
AmpliÞer Rear L/R RCA inputs
Speaker-level audio outputs
From: AmpliÞer outputs
+ -
+ -
To:
Speaker input posts
RIGHT
TWEETE
(CURR
Note: The remaining channels can
be used to drive other speakers,
or left unconnected.
+ -
RIGHT
+ -
LEFT
R
LEFT
W
OOFER
ENT
SOURCE
W
OOFER
TWEETE
(CURR
)
R
LO
UDSPEAKER
ENT
S
SOURCE
)
U
Biamping with an external
crossover
N
BALAN
C
PU
E
D
T
PR
E
AMP O
U
T
L
S
R
If you have an external active
crossover, you can greatly increase
the efÞciency of your system. The
crossover will split the preampliÞer
output signals into two frequency
ranges.
FUL
RAN
L FR
E
Q
G
E
AC
T
IVE
E
XTE
R
N
AL C
R
O
S
S
O
VE
R
INPUT
HIGH
R
OUT
L
LO
R
W OUT
R
L
You can connect the crossover's
low frequency outputs to the ampli-
Þer's rear channel inputs, and the
crossover's higher frequency outputs
to the ampliÞer's front channel inputs.
L
HIGH FREQ
RANGE
LO
W FREQ
RANGE
This is an efÞcient system because
the channels only amplify signals with-
in the frequency range of the speaker
element they are driving. Little power
is wasted.
Make sure that the crossover point
of your active crossover is adjusted
to match the crossover point of your
speakers. Consult your speaker and
crossover owner's manuals.
+ -
TWEETE
+ -
RIGHT
+ -
RIGHT
WO
+ -
R
LEFT
O
FER
(CURR
SOURCE
ENT
LEFT
WO
O
FER
TWEETE
(CURR
)
R
LO
UDSPEAKER
ENT
S
SOURCE
)
13
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Biwiring Connections
If your speakers can be biwired or
biamped, they will have completely
separate input terminals for the woofer
section and the upper range. See the
speaker diagram and discussion on
page 12.
UNBALANCED
PREAMP OUTPUTS
R
L
Line-level audio signals
From: PreampliÞer main RCA outputs
Make sure that any links be-
tween the woofer and upper
range posts are removed
from the speakers when
To:
AmpliÞer line-level inputs
you want to biamp or biwire them.
Consult your speaker owner’s
manual for details.
The front channels of the Cinema
Grand AmpliÞer each have two pairs
of outputs which can be used to biwire
your speakers. The idea is to use the
voltage source to drive the woofer,
and the current source to drive the
upper range. This will offer improved
performance and still allow you to con-
nect seven speakers for your Home
Theater system.
Speaker-level audio outputs
From: AmpliÞer outputs
To:
Speaker input posts
This page shows the input and out-
put connections for Biwiring a left front
speaker and a right front speaker.
The remaining speaker connections
have been omitted from this drawing
for clarity. They can be connected as
shown on pages 10 and 11.
+ -
+ -
R
IG
H
T
R
IG
H
T
TW
U
O
+ -
E
R
U
E
R
R
TE
R
T
)
W
(V
O
+ -
O
O
A
R
(C
S
FE
G
LE
R
E
)
FT
E
C
N
E
LE
FT
O
LT
TW
U
E
R
U
E
R
TE
R
Output connections
W
O
O
S
O
LT
U
O
U
FE
(C
S
C
E
R
E
)
E
C
N
E
T
)
•
Connect the ampliÞer’s right
front voltage source output
to the right speaker’s woofer
input terminals. Connect the
ampliÞer’s right front current
source output to the right
speaker’s upper range input
terminals.
(V
S
A
G
O
R
R
C
E
LOUDSPEAKERS
Input connections
Connect your preampliÞer’s outputs
to the corresponding input jacks on
the Cinema Grand.
•
Connect the ampliÞer’s left
front voltage source output to
the left speaker’s woofer input
terminals. Connect the ampli-
Þer’s left front current source
output to the left speaker’s
upper range input terminals.
14
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Series and Parallel speaker connections
The connection of more than one
speaker per channel will tend to
degrade the speaker’s frequency
response, and may make the ampliÞer
Parallel
For example, if you want to parallel-
connect two speakers to the front right
•
•
Ideally, the total average
impedance should be no less
than 2 ohms per channel.
channel of the ampliÞer:
run hot. For the best results use one
speaker per channel.
You must make sure that the
lower impedance does not
cause the ampliÞer to over-
heat, shut down, blow the line
fuse, or pop your circuit break-
er. If this happens, you should
reduce the number of speakers
wired in parallel, rewire them in
series, or use more than one
power ampliÞer.
If you do want to connect more than
one speaker per channel, there are
two main ways: Series or Parallel.
Amplifier
Outputs
Series
For example, if you want to
series-connect two speakers to the
front right channel of the ampliÞer:
•
•
The positive output terminal of
the right channel connects to
the positive input post of the
Þrst speaker and to the positive
post of the second speaker.
Amplifier
Outputs
The negative output terminal
of the right channel connects
to the negative input post of
the Þrst speaker and to the
negative post of the second
speaker.
•
•
•
•
The positive output terminal of
the right channel connects to
the positive input post of the
Þrst speaker.
•
The total impedance of equal
speakers in parallel is found
by dividing the impedance of
one speaker by the number of
speakers. For example, two
eight ohm speakers in parallel
is a four ohm load (eight ohms
divided by two), four eight ohm
speakers in parallel is a two
ohm load (eight ohms divided
by four).
The negative input post of the
Þrst speaker connects to the
positive input post of the sec-
ond speaker.
The negative input post of the
second speaker connects to
the negative output terminal of
the right channel.
The total impedance of speak-
ers in series is found by adding
their impedances together. For
example, two four ohm speak-
ers in series is an eight ohm
load.
•
Parallel connections are harder
on the ampliÞer than series
connections, as the total im-
pedance is lower compared to
driving a single speaker, and
the ampliÞer must produce
more current to drive them.
•
Series connections are easier
on the ampliÞer than parallel
connections as the total imped-
ance is higher than driving a
single speaker.
15
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Troubleshooting Guide
The SunÞre AmpliÞer is expertly
designed and built to provide years of
trouble-free performance. Most prob-
lems that occur can usually be solved
by checking your setup or making
sure that the audio and video com-
ponents connected to your processor
are on and fully operational.
•
Try to have all of your equipment
on the same electrical outlet or
circuit. Group all the low power
components (preamp, CD player,
DVD etc.) on a single outlet or
power strip. This is provided that
the overall current draw from your
equipment does not exceed the
rating of the outlet or breaker.
The ampliÞer shuts down
often or the line fuse blows
often
•
Check that the positive and nega-
tive speaker wires are not shorted
together.
•
Make sure that no speakers are
shorted internally. If you have an
ohm-meter, disconnect the speaker
wires and measure the resistance
between the speaker’s positive
and negative terminals. If the read-
ing is less than 2 ohms, the speak-
ers may have an internal short.
Measure all speakers and check
their impedance speciÞcations.
The following information will help
you deal with common setup problems
you may experience during normal
use of your unit. If the problems still
persist, please contact your SunÞre
Dealer for assistance.
•
Disconnect all cables which come
from outside the room, and check
if the hum goes away. This in-
cludes such connections as cable
TV, satellite TV, or roof top an-
tennas. Make sure that they are
disconnected where they Þrst enter
the room, so they are making no
connection to the preampliÞer or
the TV, or any other component. If
the hum is caused by the cable TV
line, then you will need a “ground
loop isolator.” This is an inexpen-
sive device Þtted in line with the
coaxial cable feed. Contact your
cable company or your SunÞre
Dealer for assistance.
No sound from one or
more speakers
•
Speaker cables may have come
undone. Turn off your system and
check the cables, and tighten the
ampliÞer and speaker binding
posts.
•
•
If you have connected speakers
in Parallel, the overall impedance
may be too low. It is recommended
that you rearrange the speakers
in Series to increase the overall
impedance, thus taking some of
the load off the ampliÞer.
•
•
Broken audio cable.
The preampliÞer volume level is
low for the channels concerned.
Recheck the preampliÞer calibra-
tion procedure.
Make sure that the ampliÞer has
good ventilation and is not over-
heating. Use the crystal base to al-
low good airßow underneath. If the
ampliÞer is in a closed rack, open
up the rear panel or use a quiet fan
for improved ventilation.
•
•
Disconnect all connections from
the preampliÞer to your TV, VCR or
DVD.
•
•
A preampliÞer Mute switch may be
on, or an external processor loop
or a tape monitor loop is engaged.
As a test, disconnect any other
component which has a grounded
power cord.
Check that your preampliÞer or
source is running the correct sur-
round sound mode. Maybe it is set
for stereo when you were expect-
ing 5.1 surround sound.
A hum is heard in your
speakers
This problem is more than likely
caused by a “ground loop” in your sys-
tem, rather than a fault in the ampliÞer.
Follow these steps to isolate the main
cause of the hum; there may even be
more than one.
NOTE: Never remove the ground pin
from any power cords. This is very
dangerous.
•
•
•
If the hum persists, disconnect all
the source components one at a
time from the back of the preampli-
Þer, until you identify the problem.
•
Check in case any missing chan-
nels have been turned off in a
preampliÞer setup menu. For
example, the center ampliÞer
channel will not receive a signal
if the preampliÞer has been set to
"Phantom."
Ground loop isolators are available
for audio lines and video. You can
ask your SunÞre Dealer for assis-
tance.
•
If your preampliÞer has XLR bal-
anced outputs, use them because
they offer greater immunity to
noise Þelds.
•
•
The Auto/on/off switch might be in
the off position.
Try moving the speaker cables
away from any power cords. Try
just one speaker, connecting it to
each ampliÞer channel and see if
one channel is bad.
•
Remember to turn off all compo-
nents in your system, including
the ampliÞer, before disconnecting
or connecting any cables during
troubleshooting.
One of the fuses for the current
source outputs may have blown.
16
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
•
Check that the interconnect cables
to the ampliÞer do not have any
broken connections.
Poor bass performance
•
Make sure that your preamp does
not have the bass level turned
down.
Other causes of noise
•
•
Many surround preampliÞers have
controls which can direct all the
bass to subwoofers, or let your
main speakers play the full range.
Make sure that the preampliÞer
has been correctly set. If you are
not using a subwoofer, set the
speaker options to “Large.”
Speaker noise may also be caused
by interference or noise on your
AC line. Make sure there are no
large appliances sharing the line,
or halogen lamps or lamps with
dimmer controls.
•
•
•
•
Try connecting your system to an-
other AC socket on a separate line.
•
Check that the speaker wires have
been connected correctly: Make
sure that the positive of each
Keep power cords away from au-
dio cables.
speaker connects to a positive out-
put of the ampliÞer, and the neg-
ative of each speaker connects to
a negative output. If one speaker is
wired incorrectly, than it will be “out
of phase” with the others, resulting
in poor bass performance.
Do not place the preampliÞer di-
rectly on top of the ampliÞer.
If the hum is heard from within
the ampliÞer and not through the
speakers, this may also be caused
by interference on the AC or DC
lines. The power transformer
may turn this interference into an
audible noise. Internal hum can be
made worse by a shelf or cabinet
resonating, so try moving the am-
pliÞer to another shelf.
•
If you have connected the ampliÞer
using the XLR inputs, make sure
that the XLR cables are wired cor-
rectly. If one has the hot and cold
reversed, then this will also cause
a speaker to be out of phase.
•
•
Try moving your preampliÞer
further away from your ampliÞer.
Sensitive preamp circuits may pick
up hum from the ampliÞer trans-
former’s magnetic Þeld.
Turn-on and turn-off
thumps
•
Plug the ampliÞer into an
unswitched AC outlet, and use the
AUTO-ON feature. This will allow
the ampliÞer to turn on and off
silently.
Try moving your components further
away from the TV, especially if
you ever notice the screen has
changed color in the area closest
to the component.
Current source outputs not
working
•
•
If you have very high efÞciency
speakers, these may show up
noise which other speakers may
not.
•
If you are biamping or biwiring,
make sure that the current source
fuses have not blown.
If you are still having a problem,
remember that SunÞre’s dealers
and technical support staff will as-
sist you. Make a list of the things
you have tried.
•
If these fuses blow often, it is
acceptable to replace with a slo-blo
7 ampere fuse.
17
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
SpeciÞcations
Removable terminal block, and
dual 1/8" minijacks for daisy-chain-
ing.
RCA Input impedance
24 kΩ
Signature 400~seven
Input sensitivity for rated
output
Power Consumption
Power output
45 W
At idle
400 watts continuous, per chan-
nel, into eight ohms, from
20 Hz to 20 kHz with no more
than 0.5% T.H.D.
Unbalanced: 1.34 Vrms
580 W
1800 W
Typical (1/8th power)
Absolute Max (Fuse
Limit)
Balanced:
0.67 Vrms
XLR Input impedance
Dimensions and Weight
10 kΩ, each leg balanced to
ground
Power at clipping, min
17.0 inches wide
800 watts per channel into four
ohms.
5.9 inches high (including feet)
16.7 inches deep (to tips of con-
nectors)
Female XLR
Pin 1 is ground
Pin 2 is positive (hot)
Pin 3 is negative (cold)
1600 watts per channel into two
ohms (time limited basis).
Weight 40 lbs
Hum and Noise
Finish
12 VDC Trigger Inputs
-118 dB, A-Weighted
Brushed aluminum with black
anodize
Input voltage range 5 -18 VDC
Maximum output current
Impedance: approx 600 Ω
120 amps peak to peak per ch.
(20 mA @ 12 V)
Removable terminal block, and
dual 1/8" minijacks for daisy-chain-
ing.
200~seven
Maximum output voltage
56.6 Vrms
Power output
Output impedance Front
Left and Right channels
Power Consumption
200 watts continuous, per chan-
nel, into eight ohms, from
20 Hz to 20 kHz with no more
than 0.5% T.H.D.
45W
At idle
280W
1800W
Typical (1/8th power)
Absolute Max (Fuse
Limit)
Voltage source: Approx. zero ohms
Current source: Approx. one ohm
Power at clipping, min:
RCA Input impedance:
Dimensions and Weight
400 watts per channel into four
ohms.
24 kΩ
17.0 inches wide
Input sensitivity for rated
output
5.9 inches high (including feet)
16.7 inches deep (to tips of con-
nectors)
800 watts per channel into two
ohms (time limited basis).
Unbalanced: 1.9 Vrms
Hum and Noise
Weight 34 lbs
Balanced:
0.95 Vrms
-115 dB, A-Weighted
Finish
XLR Input impedance:
Maximum output current
Brushed aluminum with black
anodizing
10 kΩ, each leg balanced to
ground
80 amperes peak to peak per
channel
Female XLR
Maximum output voltage
Pin 1 is ground
Pin 2 is positive (hot)
Pin 3 is negative (cold)
40 Vrms
Output impedance Front
Left and Right channels
© 2004 SunÞre Corporation.
All rights reserved. SunÞre Corpora-
tion reserves the right to improve
its products at any time. Therefore,
speciÞcations are subject to change
without notice.
12 VDC Trigger Inputs
Input voltage range 5 -18 VDC
Voltage source: Approx. zero ohms
Current source: Approx. one ohm
Impedance: approx 600 Ω
(20 mA @ 12 V)
Manual part # : 913-115-00 Rev A
18
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Limited Warranty
Service Assistance
SunÞre Corporation is proud of its
products which have been built with
care using advanced technology and
premium component parts. Your unit
has been crafted to perform properly
for many years. SunÞre Corporation
offers the following Warranty to you,
the owner of a new SunÞre product:
SunÞre Corporation’s liability is
limited to the repair or replacement,
at our option, of any defective prod-
uct and shall not in any event include
property or any other incidental or
consequential damages which may
result from the failure of this product.
We suggest that you read the Limited
Warranty completely to fully under-
stand your Warranty/Service cover-
age.
If your SunÞre Corporation product
ever requires service, write to us or
call:
Some states do not allow limitations
on how long an implied warranty lasts
and/or do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitations or
exclusions may not apply to you.
SunÞre Corporation
Technical Services Department
P.O. Box 1589
Snohomish, WA 98291
Tel (425) 335-4748
Fax (425) 335-4746
The SunÞre Corporation Warranty
for the Cinema Grand AmpliÞer is in
effect for FIVE years from the date of
original retail purchase. The SunÞre
Corporation Warranty covers defects
in materials and workmanship. The
following, however, are excluded:
This Warranty gives you speciÞc
legal rights, and you may also have
other rights which vary from state to
state. We suggest that you attach your
purchase receipt to this Warranty and
keep these in a safe place. Thank you
for your choice of a SunÞre Corpo-
ration product.
You will be directed to an autho-
rized SunÞre Corporation Service
Station or receive instructions to ship
the unit to the factory. Please save the
original shipping carton and packing
materials in case shipping is required.
Please do not ship Parcel Post.
a) Damage caused during ship-
ment.
b) Damage caused by accident,
misuse, abuse of operation
contrary to the instructions
speciÞed in the SunÞre Corpo-
ration user’s manual.
NOTE: Before sending in your unit for
repair, you must call SunÞre for return
authorization.
c) Units where the serial number
has been defaced, modiÞed or
removed.
Include a complete description of
the problem, indicating how you have
it connected, the associated equip-
ment in your system and a copy of
your purchase receipt. Initial shipping
costs are not paid by SunÞre Corpora-
tion; return ground shipping costs will
be prepaid if repairs were covered by
the scope of this Warranty.
d) Damage resulting from modi-
Þcation or attempted repair by
any person not authorized in
writing by SunÞre Corporation.
e) Units purchased from unau-
thorized dealers.
The SunÞre Corporation War-
ranty extends to the original owner
or subsequent owner(s) during the
Þve year warranty period, so long as
the original dated purchase receipt is
presented whenever warranty service
is required.
All implied warranties, including
warranties or merchantability and
Þtness for particular purposes, are lim-
ited in duration to the Þve year length
of this Warranty, unless otherwise
provided by state law.
19
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Cinema Grand
Signature 400 ~ seven
and 200 ~ seven
seven
Manual part number : 913-115-00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|