®
Pro Glide Plus 8700
Advanced Steam Generator
Instruction Booklet
SR8700
Please read these instructions carefully
and retain for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR IRON
•
Do not wind the cord around the soleplate
while the iron is still hot.
Do not leave the steam generator unattended
while it is plugged into the power outlet.
•
Do not leave a hot iron within reach of
children. If they come into contact with a hot
iron it could lead to serious burns.
•
•
•
Iron only on an ironing board. Do not place the
steam generator on carpet during use.
•
The steam generator must be used and rested
on a stable surface. When placing the steam
generator on a stand, ensure that the surface
on which the stand is placed is stable.
The steam generator is not to be used if it has
been dropped, if there are visible signs of
damage or if it is leaking.
This steam generator features an “auto-off”
function, which is an additional safety feature
designed to disconnect power to the heating
element if the steam generator has not been
used for a certain period of time.
The steam generator must not be stored whilst
it is connected to the supply. The electronic
switch provided is for functional use only
during operation, and is not intended to
provide disconnection from the supply.
Before storing the iron after use, it must be
unplugged from the supply.
The steam generator takes approximately 2
hours to completely cool down. Allow the steam
generator to cool completely before storing.
•
•
•
Sunbeam is very safety conscious when designing
and manufacturing consumer products, but it is
essential that the product user also exercise care
when using an electrical appliance. Listed below
are precautions which are essential for the safe use
of an electrical appliance:
•
•
Do not use an appliance for any purpose
other than its intended use.
Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
•
•
Do not place on top of any other appliance.
Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
•
Read carefully and save all the instructions
provided with an appliance.
•
Always turn the power off at the power outlet
before you insert or remove a plug. Remove by
grasping the plug - do not pull on the cord.
Turn the power off and remove the plug when the
appliance is not in use and before cleaning.
Do not use your appliance with an extension cord
unless this cord has been checked and tested by
a qualified technician or service person.
Always use your appliance from a power outlet of
the voltage (A.C. only) marked on the appliance.
This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they
do not play with the appliance.
The temperature of accessible surfaces may be
high when the appliance is operating.
•
Do not operate any electrical appliance with a
damaged cord or after the appliance has been
damaged in any manner. If damage is suspected,
return the appliance to the nearest Sunbeam
Appointed Service Centre for examination, repair
or adjustment.
For additional protection, Sunbeam recommend
the use of a residual current device (RCD)
with a tripping current not exceeding 30mA in
the electrical circuit supplying power to your
appliances.
Do not immerse the appliance in water or any
other liquid unless recommended.
Appliances are not intended to be operated by
means of an external timer or separate remote
control system.
•
•
•
•
•
•
•
•
This appliance is intended to be used in
•
•
•
household and similar applications such as: staff
kitchen areas in shops, offices and other working
environments; farm houses; by clients in hotels,
motels and other residential type environments;
bed and breakfast type environments.
Never leave an appliance unattended while in
use.
If you have any concerns regarding the performance and use of your appliance,
3
Ensure the above safety precautions are understood.
Download from Www.Somanuals.com. All Manuals Search And Download.
Features of your Pro Glide®
Plus 8700 Steam Generator
Constant Steam Button
When ironing for long periods the constant
steam button can be activated to produce
continuous steam eliminating the need to
hold the trigger down during ironing.
Iron rest
Place the iron on the heat resistant iron rest
between garments.
Refillable water tank cover
The removable 1400ml capacity tank has
a large filling hold to make it easier to refill
during ironing. The tank is tap water safe and
contains an anti-calc crystal bag which helps
reduce mineral build up.
Lock & Carry
The iron can be locked into the steam generator
base when it is not being used. This also enables
the steam generator to be transported easily.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Thermostat light
The thermostat light illuminates to
indicate that the iron sole plate is heating,
and goes out when it has reached the
temperature selected on the temperature
dial. The thermostat light cycles on and
off during ironing as the iron sole plate
maintains the selected temperature.
Steam Trigger
Press and hold the steam release trigger
to produce a constant stream of high-
powered steam to reduce your ironing time
and effort. Steam will not be emitted from
the iron when the steam release trigger is
not depressed.
Lock & Carry Release
When the iron is locked into the steam
generator base the release lever on the
base of the iron can be depressed to
release the iron
.
Variable temperature dial
The variable temperature dial adjusts
the temperature of the iron sole plate,
allowing you to select the desired
temperature for each garment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Features of your Pro Glide Plus 8700 Steam Generator
continued
Power On Button
Steam Rate Dial
The power on button
will be illuminated WHITE
when the unit is turned on.
The steam rate can be
selected by turning the
steam rate dial to
the
preferred level of steam.
Once selected the steam
ready indicator changes
from red to green when
the level has been
Calc Clean Indicator
The Calc Clean indicator
illuminates WHITE when
its is time to flush the
boiler.
reached.
Low Water Indicator
The low water indicator
illuminates RED when it
is time to refill the water
tank.
Steam Ready Indicator
The steam ready indicator
illuminates GREEN
when the steam can be
activated.
Calc Clean Boiler Cap
The calc clean indicator on the control
panel illuminates when its is time to flush
the boiler. The calc clean boiler cap allows
you to flush the boiler. Turn the calc clean
boiler cap anti clock wise to remove it.
Follow the instructions on pages 11-12 to
decalcify the boiler.
Note: The steam generator must be
completely cooled before the calc clean
boiler cap is removed. Wait 2 hours after
use for the appliance to cool down.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Pro Glide® Plus 8700
Steam Generator
Before first use
Filling the steam generator tank with water
The tank can be removed and refilled
from the tap or using a jug through the
water inlet. Do not exceed the maximum
water level indicator. Ensure the water
inlet is closed and the water tank is
firmly in position.
NOTE: The boiler will not activate until
the water tank is in the correct position.
If the low water indicator remains
illuminated when the tank has been
replaced, slide the tank out and firmly
reinsert to ensure it is in the correct
position.
NOTE: The non-corrosive stainless steel
boiler has been designed to allow you
to use tap water in your professional
ironing system. However in very hard
water areas, Sunbeam recommends the
use of distilled water, or water which
has been demineralised.
Remove any adhesive stickers, plastic
covers or cardboard sleeves from the
soleplate. Ensure that all adhesive is
removed by rubbing the soleplate with a
cloth dampened with methylated spirits.
Fill the water tank and empty the water.
This will rinse out any foreign particles
remaining in the water tank from the
manufacturing process.
NOTE: When turned on for the first time,
your new iron may give off vapours
for up to 10 minutes. This is due to
the initial heating of the materials
used. It is safe, not detrimental to the
performance of the iron, and will not
reoccur.
NOTE: Ensure the steam generator is
always used and rested on a stable
surface. Do not move or shake the base
unit during use.
For best performance, we recommend
the use of Sunbeam Water Demineraliser
or Sunbeam Demineralised Water
available from selected retailers.
Do not fill the iron with fabric
conditioner, starches or any other
solution as these will damage the steam
mechanism. Do not use contaminated
water.
NOTE: Sunbeam recommend using
the SR8700 steam generator with
the SB8300 Couture Ironing board
which has a metal tray underneath the
board specifically designed for steam
generators. This is available from
selected retailers.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Pro Glide® Plus 8700 Steam Generator (continued)
Using your iron
stable at the new setting by allowing the
thermostat to cycle once (the thermostat
light will turn on / off once).
4.Select the desired steam level by
turning the Steam Rate Dial to the
desired setting (as shown in
1.Insert the plug into a 230/240 volt
power outlet and turn the power on.
2.Select the power button to turn the
unit on. The Power On icon illuminates
WHITE as shown in Fig 1, and the unit
beeps once. The boiler and soleplate
will begin heating and the Steam
Ready light illuminates RED.
Fig 3).
NOTE: To prevent water dripping from the
soleplate, only use the steam function
when the temperature of the soleplate is
set to Silk or above.
Figure 3
Figure 1
5.When the steam selection illuminates
GREEN, the unit is ready to use.
NOTE: The Steam Ready light will
illuminate GREEN when the steam
can be activated, usually after 2 1/2
minutes. However, it may take a bit
longer for the steam to be at maximum
power depending on the volume of
water in the boiler and the tank and the
ambient temperature of the water.
Before using the steam generator on
a garment, direct a shot of steam
into the air to release any remaining
condensation.
3.Turn the temperature dial on the
iron to the desired setting (set the
temperature to Silk or above when
using steam). The thermostat light
(as shown in Fig 2) will illuminate
AMBER to indicate that the iron is
heating. It will go out once the iron
has reached the selected temperature.
Figure 2
NOTE: When changing the temperature
dial from a higher setting to a lower
setting, ensure the iron temperature is
8
Figure 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Pro Glide® Plus 8700 Steam generator (continued)
5.Press and hold the steam release
trigger to iron with steam. Use the
constant steam button for continuous
steam when ironing tough garments.
To dry iron, do no press the steam
trigger button or turn the steam rate
dial to 0.
time during ironing but the boiler may
take a few minutes to return to the
correct temperature.
1.Using a jug slowly pour water into the
water inlet until the maximum water
level is reached. Do not exceed the
maximum water level indicator.
2.Push the water inlet cover firmly to
close.
3.The Steam Ready light may illuminate
RED if the steam rate setting is
changed.
5.Recommence ironing when the Steam
Ready light illuminates GREEN.
NOTE: Both the steam ready indicator
and the thermostat light will cycle on
and off during ironing as the ironing
system maintains the selected steam
pressure and temperature levels.
Once you have finished ironing, switch
the iron and boiler off by pressing and
the power button for. Switch the power
off at the power outlet and remove the
plug. Wait for the iron to cool completely
before storing.
Warning: "Do NOT empty the boiler
during use or at anytime when the steam
generator is hot.
Warning: Never touch the soleplate at
any time when it is hot.
Safety Auto-Off
The safety auto-off mechanism
automatically turns the ironing system
off if you forget. The boiler will
automatically shut off if any button,
trigger or dial is not used for 15 minutes
or more.
Should you leave the ironing system
unattended a warning beep will sound to
let you know that the auto-off function
has been activated. After 30 seconds
the power to the boiler will be cut, the
soleplate will remain at the selected
temperature and the Power light will
continue to flash. In order to start using
the iron again, any button or trigger can
be pressed to reactivate the boiler. Allow
the boiler to heat up until the steam
ready light illuminates GREEN.
NOTE: Ensure the steam generator is
used and rested on a stable surface.
Refilling the tank during ironing
When the water in the tank falls below
the minimum level, the low water
indicator will flash RED, as shown in fig
5, the steam generator beeps three times
and the iron will stop generating steam.
The water tank can be refilled at any
After 60 minutes of the any button,
trigger or dial not being used, power to
the iron's heating element will be cut
and the iron will start to cool down.
In order to start using the iron again
any button, trigger or dial needs to be
pressed to power back up the boiler and
9
Figure 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Pro Glide® Plus 8700 Steam Generator (continued)
the iron. Allow the iron to heat up until
the thermostat light on the iron goes out
and the steam ready light illuminates
GREEN.
Calc Clean Reminder
Mineral deposits in tap water solidify
when the water is heated and can build
up in the steam holes and boiler system
which can affect steam performance.
The Calc Clean light illuminates
WHITE to remind you when it is time
to flush the boiler. The Calc Clean light
illuminates after approximately 20
hours of use. It is important to regularly
flush out the boiler to maintain the
performance of the ironing system.
NOTE: The auto off is only activated after
15 minutes of the steam not being used.
NOTE: When you reactivate the iron
after it has been in auto off mode water
may have been trapped in the steam
hose. Therefore before using the steam
generator on a garment direct a shot
of steam into the air to release any
remaining condensation.
NOTE: If all the lights on the control
panel illuminate and flash you must
decalcify the unit immediately. If the
lights continue to flash after you have
decalcified the unit please call Customer
Services on 1300 881 861.
SEE CARE & CLEANING SECTION ON
PAGE 10.
Figure 6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
After each use
1.Turn the power off and remove the plug
from the power outlet.
2.Allow the iron to cool before storing.
Storage
Empty the water tank before storage.
Always store the iron on the base of the
steam generator.
Insert the power cord into the storage
compartment.
Wrap the steam cord around the machine
for ease of storage.
Warning: "Do NOT empty the boiler
during use or at anytime when the steam
generator is hot
Figure 7
Calc Clean Reminder
Mineral deposits in tap water solidify
when the water is heated and can build
up in the steam holes and boiler system
which can affect steam performance. It is
important to regularly flush out the boiler
to maintain the performance of the ironing
system.
Cleaning
To clean the exterior of your iron, wipe
over with a damp soft cloth and wipe dry.
The Calc Clean light illuminates WHITE
to remind you when it is time to flush the
boiler. The Calc Clean light illuminates
after approximately 20 hours of use.
Caution: Do not use harsh abrasives,
chemical cleaners or solvents to clean the
exterior of your iron as these will damage
the surface.
Calc Clean instructions – using Sunbeam
Ironing System Descaling Tablets
Cleaning the steam holes
To remove build up from the steam holes
which may affect steam performance,
use a cotton wool tip moistened in
methylated spirits.
NOTE: 1x6g descaling tablet (SR0100) has
been included with the SR8700. These
are also available from selected retailers.
Dissolve 1 x 6g tablet in 400ml of warm
water (90 degrees is recommended) in a
jug before use.
Cleaning the soleplate
Wipe with a soft damp cloth and wipe dry.
Caution: Do not use scouring pads,
abrasives or harsh cleaners to clean your
Teflon Platinum Pro soleplate, as these will
scratch and damage the surface.
1.To flush the boiler, turn the unit off and
wait for it to cool completely (approx 2
hours).
2.Place the unit on a waterproof surface,
or on the edge of the sink.
Caution: If the unit has been used prior to
descaling the boiler the calc clean boiler
cap will be very hot. Ensure that the unit
has cooled completely before commencing
the Calc cleaning process.
Warning: Do NOT empty the boiler
during use or at anytime when the steam
generator is hot.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning (continued)
3.Slowly turn the calc clean boiler cap anti
clock wise. See fig 7.
Note: The boiler cap needs to be released
slowly to release any remaining water.
12. Once you have completed the descaling
process, and refilled the tank, press
and hold the Power button for 3
seconds to switch off the Calc Clean
indicator light. The power light will
illuminate and the unit will begin
heating as normal.
Note: Sunbeam Steam Ironing System
descaling tablets (SR0100) are available
from selected department stores and
electrical retailers.
Calc Clean instructions – using lemon juice
Alternatively, if you do not have Sunbeam
Ironing System Descaling Tablets, you can
use lemon juice to remove the scale build
up from inside the unit’s boiler.
Figure 8
4. Remove the calc clean valve
completely. See fig 8.
1. To flush the boiler, turn the unit off
and wait for it to cool completely
(approx 2 hours).
2. Place the unit on a waterproof surface,
or on the edge of the sink.
5. Place the unit on its side and remove
any remaining water. Carefully pour
the descaling solution into the boiler.
Replace the calc clean valve.
6. Return the unit to the upright position
and leave for 2 minutes.
7. Shake the unit back and forth to
dislodge any scale build up on the base
of the boiler. Leave for 10 minutes.
8. Shake the unit again to swirl the
solution around inside the boiler.
9. Place the unit on a sink or vessel so
that water can be expelled from the
boiler.
10. Carefully remove the calc clean valve
and ensure the descaling solution is
emptied.
11. Rinse with 400ml of water (90 degrees
is recommended), shake and empty.
Repeat rinsing process at least 2
times.
3. Slowly release the calc clean boiler cap
to release any remaining water.
CAUTION: If the unit has been used prior to
descaling the boiler the calc clean boiler
cap will be very hot. Ensure that the unit
has cooled completely before commencing
the calc cleaning process.
4. Empty any remaining water from the
boiler.
5. In a small jug, add 3 tbs lemon juice
to 400ml of warm water (90 degrees is
recommended) and stir to mix.
6. Place the unit on its side and carefully
pour the lemon solution into the boiler.
Replace the calc clean boiler cap.
7. Return the unit to the upright position
and leave for 2 minutes.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning (continued)
8. Shake the unit back and forth to
dislodge any scale build up on the
base of the boiler. Leave for 10
minutes.
9. Shake the unit again to swirl the
solution around inside the boiler.
10. Place the unit on a sink or vessel so
that solution can be expelled from the
boiler.
11. Carefully remove the calc clean valve
and ensure the descaling solution is
emptied.
12. Rinse with 400ml of water (90 degrees
is recommended) clean water, shake
and empty. Repeat rinsing process at
least 2 times.
13. Once you have completed the
descaling process, and refilled the
tank, press and hold the Power button
for 3 seconds to switch off the Calc
Clean indicator light. The power light
will illuminate and the unit will begin
heating as normal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting Guide
Problem
Possible Reason
Solution
Water is spitting
The temperature of the Turn the soleplate temperature up to Silk
from the soleplate. soleplate is set below
the Silk setting.
or above and wait for the soleplate to reach
the selected temperature. Before using the
steam generator on a garment direct a shot
of steam into the air to release any remaining
condensation.
The unit has been left
overnight and water
residue has built up in
the steam hose.
The unit has been
moved or shaken
during use.
Ensure the unit is placed on stable base and
is not moved or shaken. Ensure the soleplate
temperature is turned up to Silk or above and
wait for the soleplate to reach the selected
temperature. Before using the steam generator
on a garment direct a shot of steam into the
air to release any remaining condensation.
The Calc Clean
indicator light
illuminated.
The unit needs to be
descaled.
Wait for the unit to cool down and then
following the Care and Cleaning instructions
on page 11. Once you have completed the
descaling process and refilled the tank,
press and hold the Power button for 3 seconds
to switch off the Calc Clean indicator light.
The power light will illuminate and the unit
will begin heating as normal.
The Calc Clean
indicator light is
still on after the
unit has been
descaled.
The Calc Clean
function has not been
reset.
When you have completed the descaling
process and refilled the tank, press and hold
the Power button for 3 seconds to switch off
the Calc Clean indicator light. The power light
will illuminate and the unit will begin heating
as normal.
All the lights on the This may be a result of This could be an indication that the steam
control panel are
flashing
that the unit has not
generator has not been decalcified on a regular
been descaled properly. basis as recommended by the Calc Clean
indicator. Decalcify the unit immediately.
If the lights on the control panel continue
to flash after you have properly decalcified
the unit please call Customer Services on
1300 881 861.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing Tips and Tricks
Tip # 1 - Iron shirts like a pro
Tip # 6 - Ironing the seam
Start with the collar, working from the outer
edges into the middle. Iron the shoulder
next, followed by the cuffs and sleeves.
Place the collar at the narrow end of the
board so that one front panel of the shirt
is extended flat. Iron the front panel from
shoulder to shirt tail. Rotate to iron the
back of the shirt. Rotate and complete the
remaining front panel.
Always press seams in the same direction
they were made. When a garment is
produced, the fibres will naturally settle
in the direction they were initially pressed,
so it’s best not to iron against the grain.
Tip # 7 - Sort types of fabric
Sort articles to be ironed according to the
type of fabric. This will reduce the need to
adjust the temperature constantly. Start with
articles requiring lower temperatures and
work your way through to items requiring
higher settings.
Tip # 2 - Tips for T-shirts
Straighten seams on t-shirts before hanging
out to dry. To avoid damage to printed
graphics and logos turn the t-shirt inside out
and iron the reverse side of the print. Never
iron areas of your t-shirt where perspiration
marks are visible as the heat of the iron will
permanently fix the stain.
Tip # 8 - Summer frocks and frills
Steam is the key when ironing delicate
summer fabrics such as muslin, cotton and
linen. Don’t press down with the iron, simply
hover above the garment and steam it using
a vertical shot of steam. Ruffling, netting,
tulle or intricate hand detailing is also best
ironed using this method.
Tip # 3 - Hung out to dry
When washing is complete, remove shirts
from the machine immediately, shake them
out and hang them on coat hangers to air dry
– this will keep wrinkles to a minimum.
Tip # 9 - Pressing your winter woollies
Steam is crucial when pressing your winter
woollies. Woollen garments can be hung and
steamed using the vertical shot of steam
feature. After steaming, brush the garment
with your hand to plump up woollen fibres.
If ironing the garment flat it is best to use
a pressing cloth. Don’t be afraid to apply
pressure – steam and hold.
Tip # 4 - Selecting the right temperature
If you are unsure of the correct setting for a
particular garment, test a small area such as
a seam or inside hem before ironing a visible
area. Start with a low temperature and slowly
increase the heat to find the best setting.
Tip # 5 - Don’t be afraid to iron silk
Tip # 10 - Table settings to impress
To avoid unwanted creases always iron
your table cloth after taking it out of the
cupboard. A dinner party is a special
occasion, so treat the table cloth as you
would your own outfit. For best results, lay
towels across your table and iron the table
cloth over the towels. This will save you time
and ensure a beautifully presented table
setting.
Don’t be afraid to iron silk. Although delicate
in appearance, silk is the strongest and most
resilient of all natural fibres. To achieve the
best results, set to a low cotton setting and
use regular shots of steam. Always use a
pressing cloth to avoid shine marks.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing Chart
Fabric
Temperature Setting
Ironing recommendation
Acrylic
•
Dry iron on wrong side
Dry iron on wrong side while still damp or use
spray to dampen
Acetate
Silk
•
Iron on wrong side. Use an ironing cloth to
prevent shine marks
• •
• •
• •
• •
• •
• •
• •
Iron on wrong side while still damp or use
spray to dampen
Nylon
Iron on wrong side while still damp or use
spray to dampen
Polyester
Rayon
Iron on wrong side of fabric
Mainly dry iron. Steam can be used under
manufacturer’s instructions
Viscose
Wool
Steam iron on wrong side or use an ironing
cloth
Steam iron on wrong side or use an ironing
cloth
Wool Blends
Check label and follow manufacturer’s
instructions. Use setting for the fibre requiring
the lowest setting
Cotton Blends
• •
Steam iron on wrong side or use an ironing
cloth and brush to raise the pile
Corduroy
Cotton
• • •
• • •
Dry iron while still damp or use spray to
dampen. Use steam medium to high
Iron on wrong side or use an ironing cloth
to prevent shine marks, especially with dark
colours. Dry iron while still damp or use spray
to dampen. Use steam medium to high
Linen
• • • to Max
• • • to Max
Denim
Use maximum steam
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Year Replacement Guarantee
In the unlikely event that this appliance develops any malfunction
within 2 years of purchase (3 months commercial use) due to
faulty materials or manufacture, we will replace it for you
free of charge.
Should you experience any difficulties with
your appliance, please phone our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
In Australia you are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
Your Sunbeam 2 Year Replacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
Similarly your 2 Year Replacement Guarantee
does not cover freight or any other costs
incurred in making a claim. Please retain
your receipt as proof of purchase.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
Download from Www.Somanuals.com. All Manuals Search And Download.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
‘Solus’ and ‘Resilium’ are registered trademarks of
Sunbeam Corporation.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2006.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
8/11
Sunbeam Corporation is a division of GUD Holdings Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|