All-Weather Outdoor LCD Television
Operator’s Manual
Model SB-5560HD
Revision 5560HD-120409
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning Instructions: See “Care of SunBriteTV” on page 32
Attachments: Do not use attachments not specifically recommended by the manufacturer. Use of improper attachments can
result in accidents.
Power Source: SunBriteTV must operate on a power source indicated on the specification label. If you are not sure of the type of
power supply used in your home, consult your dealer or local power company. When using the TV outdoors, you must use a GFI-
protected AC outlet with “in-use”waterproof cover.
Installation: Do not place the product on an unstable cart, stand, tripod, table, or anywhere the unit is not permanently installed.
Placing the product on an unstable place can cause the product to fall, resulting in potential serious personal injuries, as well as
damage to the product.
Precautions when Transporting the TV: Carrying the television requires at least two people.
FCC Statement
This equipment complies with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment
and receiver.
3. Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
Modifications not expressly approved by the
manufacturer could void the user’s authority to
operate the equipment under FCC rules. This device
complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Ventilation: Adequate ventilation must be maintained to ensure reliable and continued operation and to protect
the television from overheating. Do not block ventilation slots and openings with objects, or install the television in a
place where ventilation may be hindered. There must be at least 1.5”of space on all sides.
Power cord protection: The power cord must be routed properly to prevent people from stepping on it, or objects
from resting on it. Check the cords at the plugs and product.
Power source: This product must operate on a power source specified on the specification label. If you are unsure of
the type of power supply used in your home, consult your dealer or local power company.
Do not let metal pieces or objects of any kind fall into the television from ventilation holes. High voltage flows in the
product, and inserting an object can cause electric shock and/or short internal parts.
Do not mount SunBriteTV near a motor or transformer where strong magnetism is generated. Images on the
television will become distorted and the color irregular.
Do not mount SunBriteTV near heat sources such as radiators, heaters, stoves and other heat-generating products
(including amplifiers).
Do not submerge SunBriteTV in water: The SunBriteTV will resist water exposure from normal rain, sprinklers,
garden hoses, etc.; however, it is not designed to be submerged in water.
Do not pressure-wash SunBriteTV: SunBriteTV will resist water exposure from normal rain, sprinklers, garden hoses,
etc.; However, it is not designed to withstand pressure washers, high-pressure water jets, or hurricane-type weather.
Do not service SunBriteTV yourself: Removal of the television screen cover may expose you to high voltage or other
dangerous risks. Refer all servicing to a qualified service professional. Warranty will not be honored if you service the
unit yourself.
Repair: If any of the following conditions occurs, unplug the power cord, and call a qualified service professional to
perform repairs:
When power cord or plug is damaged.
When objects have fallen into the product.
If unit was submerged in water or pressure-washed.
When product does not operate properly as described in the operating instructions. Do not touch the controls other
than as described in the operating instructions. Improper adjustments of controls not described in the
instructions can cause damage, which can require extensive repair work by a qualified technician.
When the product has been dropped or damaged.
When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the
product needs servicing.
Replacement parts: In case the product needs replacement parts, make sure that the service person uses
replacement parts provided by SunBriteTV. Use of unauthorized parts can result in fire, electric shock and/or other
danger.
Safety checks: Upon completion of service or repair work, ask the service technician to perform safety checks to
ensure that the product is in proper operating condition.
WARNING: To prevent personal injury and/or
damage to the TV or personal property, use at
least two people to install or move the TV.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Safety Instructions
Table of Contents
2
5
6
Supplied Accessories
TV Installation
Choose a Location for the TV
Rear Panel Internal Connect Source
Rear Panel Connections
Starting the TV
7
8
9
18
18
19
21
Side Panel and Front Panel Controls
Remote Control Guide
On-Screen Display Controls
Adjusting On-Screen Displays
Picture Menu
Audio Menu
21
22
24
26
29
30
31
31
32
Time Menu
Set-up
Lock Menu
Parental Menu
Channel Menu
Trouble Shooting
Care of SunBriteTV
Specifications
Features Information and Instructions
Extreme Climate Warning
Programming Other Manufacturers’Universal Remote Control Devices
SunBriteTV Pixel Quality Policy
Dust Cover
34
34
34
34
35
36
37
IR Emitter Installation
Appendix A - RS232 Control Codes
Appendix B - RS232 Control Cable Pinout
SunBriteTV Model SB-5560HD Operator’s Manual
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Unpacking
After unpacking the SunBriteTV television, please make sure that the following items are included in the carton and
that they are in good condition. If items are damaged or missing, contact your dealer immediately.
SunBriteTV LCD Television Model 5560HD
Remote Control with Batteries
Operator’s Manual
Outdoor Dust Cover
Outdoor Dust Cover
Model 5560HD
Water-Resistant
Wireless Remote
Control
Operator’s
Manual
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation - Choose a Location for the TV
Choose a location for the TV
Important: The TV must be installed at least 5
feet from pool, spa, or other body of water.
The TV should be installed so the screen is not facing
direct sunlight, or can be easily turned away from
direct sunlight.
Ideal placement is in an area where the TV is shaded
by trees, landscape and/or structures, or under a patio
cover or gazebo.
If the sun shines directly on the screen for long periods
of time, dark areas may develop on the screen. This is a
normal reaction for the LCD panel, and will not cause
damage to the screen. Either turn the screen away from
the sun, or apply shade to the TV, and the dark areas
will quickly disappear.
Important! To protect the life of the lCD screen,
keep the dust cover on the TV when the TV is
not in use.
WARNING: To prevent personal injury and/or
damage to the TV or personal property, use at
least two people to install or move the TV.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Internal Connect Source
Rear Panel Connections
WARNING: Do not connect the power source before making connections.
Internal Connect Source
The Internal Connect Source allows you to easily connect to the Audio, Video, S-Video, SVGA, HDMI, Audio Out, RF, RS232, and 12
VDC connectors, and the IR emitter window. The Internal Connect Source is inside the Cable Cover located on the back of the unit
(Figure 1).
1. Unscrew the three gray Thumb Screws (Figure 1), and pull the cover towards you.
2. Route the cables to the proper inputs, and place the cable cords over the Rubber Sealing Gasket (Figure 2).
Note: There is an Indentation on the Rubber Sealing Gasket (on the bottom portion of the right and left sides). Make sure cable
cords are not placed on the Indentation.
3. Close the cover (Figure 3).
4. Press firmly on the cover, and secure the Thumb Screws tightly (Figure 4).
Cables are to be placed over
the Rubber Sealing Gasket
Figure 2
Figure 1
Cables are not to be placed
over the indentations
Thumb Screws
Figure 3
Figure 4
Press firmly on the cover, and secure the Thumb
Screws tightly.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
1
4
6
7
8
9
9
10
12
13
2
3
5
11
14
1. SERVICE PORT - This port is for factory service only...DO NOT USE
2. HDMI 1 - Connects to devices that use HDMI cables such as Blu-ray or HD DVD player or HD cable / satellite set-top box. This
connection port receives pure digital audio and high definition signal through one single cable. This port also can accept a
HDCP video device for video or PC for monitor display usage. Use the SOURCE button to select HDMI1 on your MAIN SOURCE
to view this connection. Please note: when using HDMI, your sound signal must be PCM for the TV to decode digital audio.
When using this source for PC display, you must connect the audio cable to VGA Stereo Input for audio.
3. HDMI 2 - Same as HDMI 1
4. SERVICE PORT - This pot is for factory service only...DO NOT USE
5. VGA STEREO INPUT - This connection port is for people who want to provide audio to the TV when using a PC or a DVI video
device. Use a 3.5mm mini-jack audio cable (headphone jack) to provide audio for a HDCP enabled DVI video device or PCs
with VGA or DVI connection.
6. VGA - This connection port connects to a PC for video using VGA cable. Be sure to connect your audio cable to the VGA Stereo
input if you want sound out of the VGA video source. Use the SOURCE button to select VGA on your MAIN SOURCE to view
this connection.
7. COMPONENT 1 (Lower) - This connection ports are for DVD players or satellite/cable set-top boxes that use component
cables. From left to right, connect green, blue and red for video, and then connect white for left channel audio, red for right
channel audio. Use the Source Button to select YPbPr1 to review this connection.
8. COMPONENT 2 (Upper) - his connection ports are for DVD players or satellite/cable set-top boxes that use component
cables. From left to right, connect green, blue and red for video, and then connect white for left channel audio, red for right
channel audio. Use the Source Button to select YPbPr2 to review this connection.
9. AV 1 (CVBS or S-Video) - Connects to devices that use composite or s-video cables such as VCR or camcorder or video game
consoles. Connect the video portion with either the yellow connector or the S-Video connector. Do NOT connect both video
connectors. Use the SOURCE button to select AV1 (CVBS) on your MAIN SOURCE if you are using the yellow plug for video,
use the SOURCE button to select AV1 (S-Video on your MAIN SOURCE if you are using the S-Video connector to view this
connection.
10. DIGITAL AUDIO OUT - This connection port is used for sending out audio signals to other audio devices such as stereo/
surround sound receivers. The orange (SPDIF OUT) connector sends out either bit-stream or PCM digital sound signal to a
home theater receiver with digital input.
11. ATSC/NTSC/QAM – This connection is for digital or analog cable without the cable box or over-the-airwave antennas. The
tuner is a hybrid tuner that tunes to both analog and digital channels. This connection uses coaxial RF cable. For over- the
12. ANALOG AUDIO OUT (Variable) - Used to connect headphones, stereo receivers and amplified speakers via a 3.5mm
headphone jack.
13. IR WINDOW - For remote control using IR commands.
14. RS232 - For remote control using RS232 commands
SunBriteTV Model SB-5560HD Operator’s Manual
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
Cable Descriptions:
Connection Descriptions:
Red
Green
Blue
Yellow
Green
Red
White
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
Switching Sources for Ports:
Model 5560HD offers several options when connecting
your devices to the TV. The chart below will help you
understand which source you switch to for each of the
ports.
CONNECTINg TO AN ANTENNA
Connecting to Digital Cable without Cable Box or Antenna
Connecting to Cable or Antenna
1. Make sure the power of the TV is turned off.
1. Make sure the power to the TV is turned off.
2. Connect the Coaxial RF cable from your
antenna or digital cable to the ATSC/NTSC port off
the back of the TV.
2. Connect the Coaxial RF cable from your
antenna or cable to the
ATSC/NTSC port off the back of the TV.
3. Turn on the TV.
3. Turn on the TV.
4. Select TV (Air) for antenna or TV (Cable) for
digital cable from either your remote control’s
source button or source button on the right side
of the TV.
4. Select TV (Air) for antenna or TV (Cable) for
cable from either your remote control’s source
button or source button on the right side of the
TV.
5. Use the On-Screen Display to scan for channels.
5. Use the On Screen Display to scan for channels.
Please Note :
1. Not all broadcasts are in High Definition (HD). Please refer to your local broadcasting stations for more information.
2. The TV’s tuner is designed for HDTV therefore requires a stronger signal than normal TVs. If you cannot achieve that
signal level with your antenna or cable, the TV might lose picture or sound.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
CONNECTINg TO AN ANTENNA--(Continued)
Connecting to Cable or Antenna through VCR
Please Note :
1. Some VCRs must be turned On before its output will have
a signal to the TV. Please consult your VCR manual for further
reference.
1. Make sure the power of the TV is turned off.
2. Make sure there is an antenna or cable
connection to the VCR already.
2. Not all broadcasts are in High Definition (HD). Please refer to
your local broadcasting stations for more information.
3. Use a Coaxial RF cable and connect from your
VCR’s Antenna Out or Output to TV to the ATSC/
NTSC port of your TV.
3. The MODEL 5560HD’s tuner is designed for HDTV therefore
requires a stronger signal than normal TVs. If you cannot achieve
that signal level with your antenna or cable, the TV might lose
picture or sound.
4. Turn on the TV.
5. Select TV (Air) for antenna or TV (Cable) for
digital cable from either your remote control’s
source button or source button on the TV.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
6. Use the On-Screen Display to scan for channels.
CONNECTINg TO A DVD PlAYER
Connecting with
Component
(Better)
Connecting with HDMI (Best)
1. Make sure the power of TV and your DVD player is turned off.
1. Make sure the power of the TV and your DVD player is
turned off.
2. With a Component Cable, connect the green connector to the
DVD player and Component 1’s green connector port on the TV.
2. Connect a HDMI cable to the HDMI port of your DVD
player and the other end to the HDMI port off the back of
your TV.
3. Connect the blue color connector to your DVD player and
Component 1’s blue connector port on the TV.
4. Connect the red color connector to both your DVD player and
Component 1’s red connector port on the TV.
3. Turn on the TV and your DVD player.
4. Use the remote control’s source button or the source
button on the TV to switch to HDMI.
5. With an RCA Audio Cable, connect the white color connector to
both your DVD player and Component 1’s white connector port
on the TV.
Please Note :
Refer to the DVD player’s manual to make sure the DVD player 6. Connect the red color connector to both your DVD player and
is configured to output correctly to the TV.
7. Component 1’s red connector port on the TV.
8. Turn on the TV and your DVD player. Use the remote control’s
source button or the source button on the TV to switch toYPbPr1.
Please Note :
1. Refer to the DVD player’s manual to make sure the DVD
player is configured to output correctly to the TV.
2. This TV does not decode Bit stream digital audio, so make
sure the DVD is setup for PCM digital audio through
HDMI.
3. If HDMI 1 is occupied, use HDMI 2 as your connection
port.
Please Note :
1. If Component 1 is already occupied, please use Component 2 as
your connection port and switch to sourceYPbPr2.
2. Refer to the DVD player’s manual to make sure the DVD player is
configured to output correctly to the TV.
3. This TV will turn off automatically if there’s no signal present for
more than 15 minutes.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
CONNECTINg TO A DVD PlAYER (Continued)
Connecting with S-Video (fair)
Connecting with
Composite (Fair)
1. Make sure the power of the TV and your DVD player is
turned off.
1. Make sure the power of the TV and your DVD player is
turned off.
2. Obtain a Yellow Video Cable. Connect the Yellow Video
connector to both your DVD player and Composite’s Yellow
Video connector port off the back of your TV.
2. Obtain an S-Video Cable. Connect the S-Video connector to
both your DVD player and Composite’s S-Video connector
port off the back of your MODEL 5560HD.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your TV.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your MODEL 5560HD.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
5. Turn on the TV and your DVD player.
5. Turn on the TV and your DVD player.
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1 (CVBS).
6. Use the remote control’s source button or the source button
on the right side of the TV to switch to AV1 (S-Video).
Please note:
1. If AV 1 is already occupied, use AV2, as your connection port, and switch source to AV 2 (S-Video)
2. Reference the DVD player’s manual to make sure the DVD player is configured to output correctly to the TV.
3. This TV will turn off automatically if there’s no signal present for more than 15 minutes.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
CONNECTINg TO A SATEllITE OR CABlE SET-TOP BOX
Connecting with HDMI (Best)
Connecting with
Component (Better)
1. Make sure the power of the TV and your set-top box is
turned off.
1. Make sure the power of TV and your set-top box is turned off.
2. Obtain a Component Cable. Connect the green color
connector to both your set-top box and Component 1’s green
connector port off the back of your TV.
2. Connect a HDMI cable to the HDMI output of your set-top
box and the other end to the HDMI port off the back of
your TV.
3. Connect the blue color connector to both your set-top box and
Component 1’s blue connector port off the back of your TV.
3. Turn on the TV and your set-top box.
4. Use the remote control’s source button or the source
button on the right side of the TV to switch to HDMI 1.
4. Connect the red color connector to both your set-top box and
Component 1’s red connector port off the back of your TV.
Please Note :
5. Obtain a RCA Audio Cable. Connect the white color connector
to both your set-top box and Component 1’s white connector
port off the back of your TV to the right side of your green,
blue, red component connection.
1. Refer to the set-top box’s manual, to make sure the set-
top box is configured to output correctly to the TV.
2. If HDMI 1 is already occupied, use HDMI 1 as your
connection port and switch source to HDMI 2.
6. Connect the red color connector to both your set-top box and
Component 1’s red connector port off the back of your TV to
the right side of your green, blue, red component connection.
3. SunBriteTV’s MODEL 5560HD supports SONY’s universal
remote code. Please look up SONY’s codes in your
universal remote’s hand book.
7. Turn on the TV and your set-top box.
4. This TV will turn off automatically if there’s no signal
present for more than 15 minutes.
8. Use the remote control’s source button or the source button
on the TV to switch to YPbPr1.
Please Note :
1. If Component 1 is already occupied, please use Component 2
is your connection port and switch to source YPbPr2.
2. Please refer to the set-top box’s manual to make sure the set-
top box is configured to output correctly to the TV.
3. SunBriteTV’s MODEL 5560HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
Page 14
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
CONNECTINg TO A SATEllITE OR CABlE SET-TOP BOX (Continued)
Connecting with
Composite (Fair)
Connecting with S-Video (Fair)
1. Make sure the power of the TV and your DVD player is
turned off.
1. Make sure the power of the TV and your DVD player is
turned off.
2. Connect a Yellow Video connector to both your DVD player
and Composite’s Yellow Video connector port off the back of
your TV.
2. Obtain an S-Video Cable. Connect the S-Video connector
to both your DVD player and Composite’s S-Video
connector port off the back of your MODEL 5560HD.
3. Connect a white color connector to both your DVD player
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s
white connector port off the back of your MODEL
5560HD.
and Composite’s white connector port off the back of your
TV.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your
TV.
5. Turn on the TV and your DVD player.
6. Use the remote control’s source button or the source button
on the right side of the TV to switch to AV1 (CVBS).
5. Turn on the TV and your DVD player.
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1
(S-Video).
Please Note :
1. If AV 1 is already occupied, use AV 2 as your connection port
and switch source to AV 2 (S-Video).
Please Note :
2. Refer to the set-top box’s manual to make sure the set-top
box is configured to output correctly to the TV.
1. If AV 1 is already occupied, use AV 2 as your connection
port and switch source to AV 2 (S-Video).
3. SunBriteTV’s MODEL 5560HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
2. Refer to the set-top box’s manual to make sure the set-top
box is configured to output correctly to the TV.
3. SunBriteTV’s MODEL 5560HD supports SONY’s universal
remote code. Please look up SONY’s codes in your
universal remote’s hand book.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
4. This TV will turn off automatically if there’s no signal
present for more than 15 minutes.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
CONNECTINg TO AN EXTERNAl AMPlIFIER OR AMPlIFIED SPEAKERS
Connecting with Coaxial SPDIF Digital (Best)
Connecting with RCA Audio Analog (good)
1. Make sure the power of the TV and your receiver is turned
off.
1. Make sure the power of the TV and your receiver is turned
off.
2. Obtain a 3.5mm stereo/audio cable (if your amplifier
audio connection requires RCA audio out jacks you
will need to obtain an 1/8”Stereo Mini Plug to RCA
adapter cable). Connect it to your receiver’s audio input
connection and the 3.5mm stereo/audio connection on
the Analog Audio port on the back of the TV.
2. Obtain a Coaxial SPDIF cable, connect it to your receiver’s
coaxial SPDIF digital input and the Coaxial SPDIF
connection on the LINE OUT port off the back of the TV.
3. Turn on the TV and your receiver.
Please Note :
1. If you want pure digital stream for your receiver to
decode, you must also configure the TV’s OSD Sound-
>Digital Audio Out function. Make sure the option is on
Bit Stream.
3. Turn on the TV and your receiver.
Please Note :
1. If you want pure digital stream for your receiver to
decode, you must also configure the TV’s OSD Sound-
>Digital Audio Out function. Make sure the option is on
Bit Stream.
2. If your receiver is making static noises when receiving Bit
Stream, you must use the PCM option instead.
3. Refer to the receiver’s manual to make sure the receiver is
configured to receive signals correctly from the TV
2. If your receiver is making static noises when receiving Bit
3. Stream, you must use the PCM option instead.
4. Refer to the receiver’s manual to make sure the receiver
is configured to receive signals correctly from the TV
CONNECTINg TO A PC
1. Make sure the power of the TV and your receiver is turned off.
Connecting with DVI Digital (Best)
2. Obtain a HDMI to DVI conversion cable; connect the DVI side
of the conversion cable to the DVI output of your PC, and the
HDMI side of the conversion cable to the HDMI port off the
back of TV.
3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC
and the other end to the VGA Stereo Input Port.
4. Turn on the power to the TV and the PC.
5. From the remote control’s source button, or the Source button
from the TVs panel, switch to HDMI.
Please Note :
1. For the best picture, set your PC resolution to 1920 x 1080
at 60 Hz. Refer to the PC or graphic card manual for further
instructions on how to set your resolution and refresh rate.
2. Refer to your PC manual for video output requirements of the
video card.
3. The TV will turn off automatically if there’s no signal present for
more than 15 minutes.
4. If HDMI 1 is already occupied, use HDMI 2 as your connection
port, and switch source to HDMI 2.
Continued on next page
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
CONNECTINg TO A PC (Continued)
1. Make sure the power of the TV and your PC is turned off.
Connecting with VgA Analog (good)
2. Obtain a 15-pin D-Sub VGA cable, connect to the VGA output of
your PC and the other end to the VGA port off the back of your
TV.
3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC
and the other end to the VGA Stereo Input port.
4. Turn on the power of the TV and your PC.
5. Use the remote control’s source button or the source button the
TV to switch to VGA.
Please Note :
1. For the best results, please set your PC resolution to
2. 1920 x 1080at 60 Hz. Refer to the PC or graphic card’s manual
for further instructions on how to set your resolution and refresh
rate.
3. Refer to your PC manual for video output requirements of the
video card.
4. The VGA port of the TV features a power saving mode which will
automatically turn off the TV if there is no signal provided for
more than 15 minutes.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation--Starting the TV
Connecting the Power Cord
WARNING:
TV AND GFCI RECEPTACLE MUST BE INSTALLED AT LEAST 5 FEET AWAY FROM STANDING WATER , SUCH AS (BUT NOT LIMITED
TO) A POOL OR SPA.
Connect the power cord after you have made connections to your video equipment.
Connect the Power Cord to a GFCI-protected AC outlet
with “in-use”waterproof cover.
Warning: TV must be installed at least 5 feet away from
standing water, such as (but not limited to) a pool or
spa.
Power Cord
Back Panel
Power
Menu
Turns TV on/off.
Displays the On-Screen Display (OSD) menu.
In OSD menu, press key to return to pre-phase.
Vol+ /Vol-
Adjusts volume.
In OSD menu, both keys are used to navigate within menu.
Vol+/Vol- is used to select the highlighted options.
CH+/CH-
Source
Adjusts channels.
In OSD menu, both keys are used to navigate within the menu.
Press to change the input sources.
IR Sensor
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Guide
ON – Powers the TV On.
OFF – Powers the TV Off.
0~9 – Sets the channels.
Dash (-) – Inserts the dash for selecting digital channels directly.
R – Returns to the previous channel.
FREEZE – Freezes the TV picture. CC – Cycles between different closed
captioning modes.
SLEEP – Sets the Sleep timer.
CC– Selects Closed Caption.
V+ – Functions the Volume Up and Menu Right.
V- – Functions the Volume Down and Menu Left.
MUTE – Mutes the TVs Audio.
MENU – Opens / Exits the TV menu.
CH+ – Functions the Channel Up and Menu Up.
CH- – Functions the Channel Down and Menu Down.
MTS – Selects stereo, mono, or second audio programming.
SRS – Sets Surround Sound.
DNR – Enables the Digital Noise Reduction on the TV.
ADD/Del – Adds or deletes the current channel.
CH Lock – Locks the current channel you are on, so that kids cannot view
the locked channel unless unlocked by a password. You will also need to
input a password when locking the channel.
h / i / f / g / – Allow you to navigate inside the OSD menu. They also
function as CH+/- for digital channels in the tuner.
(Enter) – Allows you to select functions inside the OSD menu, acts as
the Enter button for OSD menu for changing channels.
SOUND – Selects various preset sound settings.
EXIT – Allows you to quit from the OSD menu..
PICTURE – Selects various preset picture settings.
GUIDE – Opens the current digital channel information guide.
SOURCE – Cycles between different inputs of the TV.
INFO – Shows current channel information, display input and resolution.
SHIFT – Used with the 0-9 numeric pad to select inputs.
ASPECT – Changes the TV between different display modes.
FAVORITE
channel list.
– Changes the channel up or down from you Favorite
FAVORITE ADD / DEL – Adds or deletes the current channel from the
favorites channel list.
Picture In Picture/Picture On Picture (PIP and POP) Functions
(Note: PIP functions are not supported on this model)
AUDIO – Switches Audio from the TV and PIP or POP windows.
VIDEO – Switches video from the PIP window to the main screen.
SOURCE – Changes the input source of the PIP window and POP window.
ON/OFF – Turns on or off the PIP and POP window.
SIZE – Changes size of the PIP window.
POS – Changes the position of the PIP window.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Guide
This remote control follows Sony’s TV remote
codes with discrete on/off and input select.
Direct TV code is 10,000
About the Water-Resistant
Remote Control
®
The SunBriteTV Water-Resistant Remote Controller is engineered to give you many years of service.
“Water-resistant”means that the remote control can be in water for short periods of time without damaging the
internal workings of the unit. It can be left in the rain, and even dropped in water, as long as it is retrieved quickly.
The remote control should not be left floating in water.
The functionality of the remote control is under warranty for one year. If the remote control malfunctions within the
one-year warranty period, replace the batteries with new long-life alkaline batteries.
If the problem is not solved with new batteries, contact the SunBriteTV Customer Care Center. SunBriteTV will repair
or replace the remote control at SunBriteTV’s option.
If you have a warranty claim, contact the SunBriteTV Customer Care Center for further instructions.
800.331.4626
On-Screen Display Controls
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Your TV has been factory-set to instantly enjoy your programming. In the event you turn on the TV and get the message, “Please
run Channel Auto Scan,” press your remote’s Menu button, Press the Channel function and press Auto Scan.
Picture:
This function
changes
the picture
settings for all
ports, such as
tint, contrast,
sharpness and
dynamic noise
reduction.
Audio:
This menu
manages
the audio
settings such
as Bass, Treble,
Balance, AVC,
SPDIF, Audio
Language, etc.
Time:
This menu
Setup:
This menu
manages
Language,
Transparency,
Zoom Mode,
Noise Reduction,
lock:
Channel:
This menu
manages Channel
functions such
as scanning
channels, editing
channels,
This menu
manages
parental
controls.
manages the
time functions
such as Sleep
Timer, Time
Zone, Daylight
Saving Time, and Closed Caption,
Clock. etc.
checking signal
strength, etc.
Adjusting On-Screen Displays – Picture Menu
Picture Menu
From the PICTURE menu you can adjust PICTURE MODE, CONTRAST, BRIGHTNESS, COLOR, TINT SHARPRESS, COLOR MODE.
Picture Mode
1. Press qp buttons to move the cursor to the item to be selected.
Press qp buttons to Picture Mode, then use t u to
adjust the Picture Mode such as Personal/Standard/
Dynamic/Soft.
2. Press t u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Contrast
Picture Menu
Press qp buttons to Contrast, then use t u to
adjust the contrast of the picture.
Brightness
Press qp buttons to Brightness, and use t u to
adjust the brightness of the picture.
Color
Press qp button to Color, then use t u to adjust the
color saturation.
Tint
Press qp button to Tint, then use t u to adjust the
tint of picture.
This function is available in the NTSC, which is one of
the color systems.
Sharpness
Press qp buttons to Sharpness, then use t u to
adjust the sharpness level of picture.
Color mode
Press qp buttons to Color Mode, then use t u to
adjust the color mode of picture, such as Cool, Normal
and Warm
SunBriteTV Model SB-5560HD Operator’s Manual
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Audio Menu
Audio Menu
1. Press qp buttons to move the cursor to the item to be selected.
Sound Mode
Allows you to you choose your sound preferences.
2. Press t u buttons to make the desired adjustments.
Press qp buttons to Sound Mode, then use t u to
adjust the Sound Mode such as Personal/Standard/
Music/Movie.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Sound Mode
Bass
Press qp buttons and then use t u button to increase
or decrease the level of the Bass response.
Treble
Press qp buttons and then use t u buttons to
increase or decrease the level of the Treble sounds.
Balance
Pressd qp buttons and then use t u buttons to
adjust the audio output level between Left and Right
Speakers.
Surround
Surround Sound is not supported on this model.
AVC
Press qp buttons and then use t u buttons to select
AVC On or Off.
SPDIF
Press qp buttons and then use t u buttons to select
SPDIF Type, such as PCM and RAM.
Audio language
Press qp buttons to select one of the audio languages
such as English/French/Spanish.
The language code must be programmed for this option
to be available. If there is no selection it has not been
programmed for this model.
Note: SPDIF Type and Audio Language are available only
in DTV.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Time Menu
Time Menu
Sleep Timer
1. Press qp buttons to move the cursor to the item to be selected.
Press qp buttons to Sleep Timer, then use t u
buttons to select the sleep timer. The options are:
Off; 5Min; 10Min; 15Min; 30Min; 45Min; 60Min;
90Min; 120Min; 180Min; 240Min.
2. Press u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Time Menu
Time Zone
Press qp buttons to Time Zone, then use t u
buttons to select the correct time zone. The options
are: Alaska; Hawaii; Pacific; Mountain; Central;
Eastern.
Daylight Saving Time
Press qp buttons and then use t u buttons to
select Daylight Saving Time ON or OFF.
When Daylight Saving Time is ON, the clocks are set
one hour ahead of local standard time.
Clock
The time is decoded from the digital signal and
displayed (such as DTV,HDMI)
This item is available only in English.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Setup Menu
Setup Menu
1. Press qp buttons to move the cursor to the item to be selected.
Menu language
Press qp buttons to Menu Language, then use t
u buttons to select menu language, the options are
English / French / Spanish.
2. Press t u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Setup Menu
Transparency
Press qp buttons to Transparency, then use t u
buttons to select Transparency ON or OFF.
Zoom Mode
Press qp buttons to Zoom Mode, then use t u
buttons to select current zoom mode, the options are
Normal / Wide / Zoom / Cinema.
Noise Reduction
Press qp buttons to Noise Reduction, then use t u
buttons to select current noise reduction level, the
options are off / Weak / Middle / Strong.
Advanced
Press qp buttons to Advanced, then press u button
to enter the Advanced Sub Menu shown below
Note: This item is only available in VGA source input.
Advanced Sub Menu
H-Pos
Press qp buttons and then use t u adjust the
horizontal position of the picture (this function
is to adjust the picture to Left/Right as to your
preference).
V-Pos
Press qp buttons and then use t u adjust
the vertical position of the picture (to adjust the
picture to Left/Right as to your preference).
Clock
Press qp buttons and then use t u to adjust
the clock of the picture. (This function is to
minimize any vertical bars or stripes visible on
the background screen. The horizontal screen
size will also change.
Phase
Press qp buttons and then use t u to adjust
the phase of the picture. (This function allows
you to remove any horizontal noise and to
sharpen the image of characters).
Auto
Press qp buttons and then press OK button
to perform the Auto Adjust function that
automatically adjusts the available options for
the best viewing configuration.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Set Up Menu
Closed Caption
From the Setup Menu, press qp buttons to Closed Caption, then press u button to enter the Closed Caption submenu list shown
below.
Closed Caption Submenu
Basic Selection
Press qp buttons and then use t u buttons
to select current zoom mode, the options are
CC1 / CC2 / CC3 / CC4 / TEXT1 / TEXT2 / TEXT3 /
TEXT4.
Advanced selection
Press qp buttons and then use t u buttons
to select current zoom mode, the options are
Service1 / Service 2 / Service 3 / Service 4 /
Service 5 / Service 6.
Option
Press the u button to enter the submenu list
shown below.
Closed Caption/OptionSub-Menu
Mode: Press qp keys to select either Default
and Custom. If you set Automatic, the other
choices are disabled and can’t be adjusted.
Font Style: press t u keys to select one of the
Defaults and from Font0 to Font7.
Font Size: press t u to select one of Default /
Normal / Large / Small.
Font Edge Style: press t u keys to select
one of Default / None / Raised / Depressed /
Uniform / Left Shadow / Right Shadow.
Font Edge Color: press t u keys to select one
of Default / Black / White / Red / Green / Blue /
Yellow / Magenta / Cyan.
Fg Color: press t u keys to select one of
Default / White / Black / Red / Green / Blue /
Yellow / Magenta / Cyan.
XVS Submenu
Bg Color: press t u keys to select one of
Default / Black / White / Red / Green / Blue /
Yellow / Magenta / Cyan.
Fg Opacity: press t u to select one of Default
/ Solid / Flashing / Translucent / Transparent.
Bg Opacity: press t u to select one of Default
/ Solid / Flashing / Translucent /Transparent.
XVS (Dynamic luminance Control)
From the Setup Menu, press qp buttons to XVS, to enter the
XVS menu. Use the t u buttons to select ON or OFF.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Lock Menu
lock Menu
Press qp buttons to move the cursor to the Enter
Password selection.
Press “Enter Password”to enter the password. (The
default password is 0000.)
To change the Password, press the u button to
enter the Lock Menu submenu
lock Menu Sub-Menu
Change password
Press u button to enter the submenu. Once
there, you can enter the new password and
confirm it. The password will be changed.
Note: If you change the password, write down
the new password, and keep it in a safe place
System lock
Press qp buttons and then use t u
buttons to select system lock ON or OFF.
When system lock is OFF, the item choices
are: US / Canada / RRT setting. Reset RRT
will be grayed
US
Press the u button to enter the submenu list
to set the US rating functions. (US Menu is
on the next page.)
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Lock Menu
US Menu
From the US Menu, press qp buttons to the TV function.
Press u button to enter the submenu shown below.
TV Menu
TV-Y: For all children
TV-Y7: For children above 7
TV-g: For anyone
TV-Pg: Children can watch with guardian
TV-14: Need parent guide
TV-MA: Only for adult
All: Select all functions above
FV: Fantasy Violence
l: Language (abusive, sexual)
S: Sexual
V: Violence
D: Dialog (sexual)
Us Menu
MPAA
From the Us Menu, press qpbuttons and use t u
buttons to select one of N/A / G / PG / PG-13 / R / NC-17
/ X.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Lock Menu
lock Menu Sub-Menu
Canada
Press the u button to enter the submenu for the
Canadian rating functions.
Canada Menu
Canada English
Press the t u button to select one of E / C /
C8+ / G / PG / 14+ / 18+.
Canada French
Press the t u button to select one of E / G /
8ans+ / 13ans+ / 16ans+ / 18ans+.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Channel
Channel Menu
1. Press qp buttons to move the cursor to the item to be selected.
2. Press t u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Channel Menu
The CHANNEL MENU is used in TV source, only.
You can complete channel search and settings here
Air/Cable
Press t u buttons to select Air or Cable.
Auto Scan
Press the u button to enter the submenu list below
Auto Scan
Cable system
Press the t u button to select the cable system.
Start to Scan
Press the u button to start auto scan.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Channel Menu
Favorite
Favorite
From the Channel Menu, press the qp buttons
to select Favorite. Press the u button to enter the
submenu shown at left.
Press qp keys to select channels, and press OK to
add current channel to Favorite Channel Table.
Follow the same directions to delete a channel from
the Favorite Channel Table.
Show/Hide Menu
Show/Hide
From the Channel Menu, press the qp buttons to
select Show/Hide. Press the u button to enter the
submenu (shown left).
Press qp keys to your desired channel. Press OK
to show or hide the specified channel.
If the channel is Hidden, user will be unable to
see the channel by pressing CH+ or CH-. They can
select the channel by pressing the channel number
directly.
Channel Menu
From the Channel Menu, press the qp buttons to
select the following functions:
Channel No.
Press the t u button to select the channel No.
Channel label
Press the u button to enter the submenu, where you
can edit the channel label.
DTV Signal
This item shows current DTV signal strength.
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
The following table contains the common problems and the solutions to these problems. Please check this list before you contact
the technicians.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Care of SunBriteTV
Caring for the LCD Panel:
1. Cleaning the lCD Panel:
Gently wipe the surface of the display panel with a soft cloth (cotton or flannel is best). Be sure the cloth is clean and does
not contain liquid cleaners or other chemicals.
If the LCD panel is very dirty, use a soft damp (with water only) cloth to gently clean the panel.
2. When the TV is not in use, keep it covered with the SunBriteTV Outdoor Dust Cover
The fitted dust cover is designed to protect the LCD panel from the harmful UV rays from direct sunlight, and keeps wind-
blown objects from scratching the surface of the panel.
To order a replacement Dust Cover, contact your Authorized SunBriteTV dealer or SunBriteTV’s Customer Care Center at
800.331.4626.
General Cleaning
Remove any dirt and salt deposits from the cabinet, being careful to rinse the cloth frequently to avoid scratching the TV or screen
surface. Avoid using harsh chemicals, abrasives, or solvents when cleaning any surface on the unit.
Snow and Ice
Use a soft brush and towel to remove snow and ice from the unit.
Fiber Filter- The Fiber Filters are located on the back of the TV, inside the Intake Vent at the top of the TV (Figure 1). Check the Fiber
Filters periodically to ensure they are free of dust and debris. Follow the procedures below to clean the filters:
CAUTION! NEVER SPRAY OR DIRECT A HOSE INTO THE VENT OPENINg OF THE TV.
1. To clean the Fiber Filter, unscrew the Filter Holder (Figure 2), and lift the Filter Holder out of the TV (Figure 3).
2. Pull the Fiber Filter out of the Filter Holder (Figure 4).
3. Clean by removing the filter and washing with warm soapy water. Allow to completely air dry overnight prior to reinstalling.
(Do not compress or squeeze filter as it will break down it’s cellular structure.)
To Order Replacement Filters, contact your Authorized SunBriteTV Dealer or SunBriteTV’s Customer Care Center at 800.331.4626.
4. Put the Fiber Filter back up into the Filter Holder and place the Filter Holder back into the TV. Screw securely.
Figure 1
Filter Holder Screws
Figure 2
Fiber Filter
Figure 3
Figure 4
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications for SunBriteTV Model 5560HD
LCD Screen
55-inch Diagonal TFT Active Matrix
1920 x 1080 full-HD 1080p
16:9
Side View
Front View
Resolution
Aspect Ratio
Contrast Ratio
Frame Rate
Viewing Angle
Response Time
TV formats
5000:1
120 Hz
176o x 176o
6.5 milliseconds
1080p, 1080i, 720p, 480p, 480i
Anti-Reflective Window Not Applicable
Input Connectors:
RF
Antenna/CATV (ATSC/QAM/NTSC) x1
All measurements are in inches
HDMI
HDMI™ Input x2
Video Composite
Video Component
S-Video x1 and Composite Video x1, L/R Audio Inputs x1
YPbPr plus Stereo Audio x2
PC
15-pin D-sub VGA plus Stereo Audio
Control Set
RS232 Serial, Discrete IR (Sony TV IR Code Set),
Concealed IR Window
Audio Out
Digital SPDIF Audio (fixed),
Analog 1/8”Headphone Jack (variable)
Speakers
20-Watt Built-in Speakers
Exterior
Outdoor-rated ASA Plastic Resin
100-240 VAC, 50-60 Hz 4.0 A Max
-24o to 122o F. (-31o to 50o C.) *
Input Power
Operating Temp.
-24o to 140o F. (-31o to 60o C.)
Non-op. Temp.
The non-operating temperature feature requires power to be applied
Heater Board
Not Applicable
Accessories Included
TV Dimensions
Weather-Proof Remote Control, outdoor dust cover
53.27” W x 33.64 ”H x 7.35”D
60”W x 46”H x 13”D
Shipping Dimensions
Weight
109.0 lbs.
Shipping Weight
Residential Warranty
Commercial Warranty
129.0 lbs.
Two-year in-factory, parts and labor
One-year parts and labor
Specifications are subject to change.
*Temperature range is for operation in shaded location.
The TV should be installed in a shaded area where the screen is not facing direct sunlight (or placed/mounted where the TV can easily be
turned away from direct sunlight).
SunBriteTV Model SB-5560HD Operator’s Manual
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Features Information and Instructions
Extreme Climate Warning
If temperatures below -24O F. are expected, we recommend that you bring your SunBriteTV inside to prevent damage to the LCD screen.
Programming Other Manufacturers’ Universal Remote Control Devices
When programming a DirectTV, local cable universal remote control or Control system, you may find that SunBriteTV may not be on the
list of TV manufacturers. If that is the case, Model 5560HD supports SONY’s universal remote code. Direct TV is 10000.
SunBriteTV Pixel Quality Policy
SunBriteTV’s Pixel Quality Policy
(Applicable to LCD TVs sold within USA and Canada only.)
SunBriteTV LCD screens are manufactured with rigorous standards to maintain optimal viewing. However, the LCD screen may
have minor defects that appear as a small bright or dark pixel. This is common to all LCD screens used in display and television
products, and is not specific to SunBriteTV.
Bright dots are dots that appear bright and unchanged in size when a LCD TV screen displays a black pattern.
Dark dots are dots that appear dark and unchanged in size when a LCD TV screen displays a pure red, green, or blue pattern.
Adjacent dots are pixels located directly next to each other.
Your SunBriteTV will be replaced under warranty if it meets one of the following criteria:
—A total of 7 defective pixels, including both bright dots and dark dots are present. (This TV screen has over a million pixels.)
—2 or more pairs of adjacent bright dots are present.
—3 adjacent bright dots are present.
—3 adjacent dark dots are present.
To locate defective pixels, the LCD panel should be examined under normal operating conditions, in its native display resolution,
with a 90 degree viewing angle, from a distance of a approximately 20 inches.
To qualify for replacement, a defective LCD screen must be reported to SunBriteTV within 60 days from the day the customer
receives the TV.
For questions, please call our Customer Care Center at 800.331.4626.
SunBriteTV Dust Cover
The SunBriteTV Dust Cover is constructed with weatherproof
nylon ripstop UV protection fabric to help keep your all-
weather outdoor television clean, protect the finish, and
ensure years of maximum enjoyment. Tighten both pull cords
to secure the cover in place.
We recommend that you keep your TV covered when not in
use.
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
IR Emitter Installation
Tie-Down
IR Window
To install the IR Emitter:
The photo to the right shows an IR Emitter* installed.
The end of the Emitter is to be mounted in front of
the IR Emitter Window.
Place the emitter on the white tie-down block and
use the tie-down to secure it in place.
Place the emitter cable over the right or left side
of the cable box and connect the other end of the
emitter to the appropriate control block*.
* Neither the emitter or control block are supplied by
SunBriteTV. See instructions that come with your IR
Emitter and control block to determine how to make the
connections.
Place IR Emitter Cable
over right or left side of
the cable box.
Tie-Down Block
IR Emitter
SunBriteTV Model SB-5560HD Operator’s Manual
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - RS232 Control Codes
RS 232 Control codes SunbriteTV
Com Spec: 9600,8,1,n
Function ASCII
Model Class ID [ESC]?
Power Status [ESC]!
HEX
Command Received Response
from TV to control system
Command Executed Response
from TV to control system
1B 3F [B3220AHD-X.XX] or
[B4610AHD-X.XX]
na
na
1B 21
[PWRON]
[PWROFF]
Power Toggle [ESC]$
Power ON [ESC]A
Power OFF [ESC]B
Tuner Input [ESC]C
1B 24 [$]
1B 41 [A]
1B 42 [B]
1B 43 [C]
1B 44 [D]
1B 45 [E]
1B 46 [F]
1B 47 [G]
1B 48 [H]
1B 49 [I]
[PWR]
[PWRON]
[PWROFF]
[TN1]
Composite Video Input 1 [ESC]D
S-Video Input 1 [ESC]E
Composite Video Input 2 [ESC]F
S-Video Input 2 [ESC]G
Component1 Input [ESC]H
Component2 Input [ESC]I
HDMI Input 1 [ESC]J
VGA Input [ESC]K
[AV1(CVBS)]
[AV1(S-VIDEO)]
[AV2(CVBS)]
[AV2(S-VIDEO)]
[YpbPr1]
[YpbPr2]
[HDMI1]
[VGA]
[HDMI2]
[MUTE]
[VOL+]
[VOL-]
[CH+]
[CH-]
na
1B 4A [J]
1B 4B [K]
1B 4C [L]
1B 58 [X]
1B 59 [Y]
1B 5A [Z]
1B 56 [V]
1B 57 [W]
1B 31 [1]
1B 32 [2]
1B 33 [3]
1B 34 [4]
1B 35 [5]
1B 36 [6]
1B 37 [7]
1B 38 [8]
1B 39 [9]
1B 30 [0]
1B 2D [-]
HDMI Input 2 [ESC]L
Mute [ESC]X
Vol Up [ESC]Y
Vol Down [ESC]Z
Channel Up [ESC]V
Channel Down [ESC]W
1
2
3
4
5
6
7
8
9
0
-
[ESC]1
[ESC]2
[ESC]3
[ESC]4
[ESC]5
[ESC]6
[ESC]7
[ESC]8
[ESC]9
[ESC]0
[ESC]-
na
na
na
na
na
na
na
na
na
na
Channel Return(Previous Channel) [ESC]r
Source Toggle [ESC]b
Aspect [ESC]a
1B 72 [r]
na
1B 62 [SRC]
1B 61 [ASPECT]
1B 65 [ENTER]
1B 69 [INFO]
1B 63 [CC]
1B 7A [SLEEP]
1B 70 [PICT]
1B 73 [SND]
na
na
Enter [ESC]e
na
Info [ESC]i
na
CC [ESC]c
na
Sleep [ESC]z
na
Picture [ESC]p
na
Sound [ESC]s
na
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B - RS232 Control Cable Pinout
SunBriteTV Model SB-5560HD Operator’s Manual
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is left blank intentionally.
Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is left blank intentionally.
SunBriteTV Model SB-5560HD Operator’s Manual
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|