Sun StorageTek™ 8 Gb FC PCI-
Express HBA, Emulex Installation
Guide
For HBA Models SG-XPCIE1FC-EM8-Z and
SG-XPCIE2FC-EM8-Z
Sun Microsystems, Inc.
Part No. 820-5465-12
December 2008, Revision A
Submit comments about this document at: http://www.sun.com/hwdocs/feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
v
Regulatory Compliance Statements vii
Safety Agency Compliance Statements xi
Preface xxiii
1. HBA Overview
1
2
3
System Support
6
Switch Support
Environmental Requirements
7
6
2. Hardware Installation and Removal
9
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
9
▼
▼
▼
▼
To Apply Power 15
(LED) Status 15
Testing the Installation 17
▼
▼
To Verify Proper Installation (for the Solaris OS) 17
To Verify Attached Storage (for the Solaris OS) 21
▼
3. HBA Software Installation 25
▼
Installing Software For the Windows Server 2003 or Windows Server 2008 OS 27
▼
To Install the Software For the Windows Server 2003 or Windows Server
Configuration and Diagnostic Utilities 28
4. Known Issues 29
Reboot Fails on the SPARC Enterprise M8000 System (6728135) 29
iv
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Compliance Model Number:
Product Family Name:
P001219
Sun StorageTek™ Enterprise 8Gb FC PCI-Express Single and Dual Port Host Bus
Adapter (SG-XPCIE1FC-EM8-Z, SG-XPCIE2FC-EM8-Z)
EMC
USA—FCC Class A
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This equipment may not cause harmful interference.
2. This equipment must accept any interference that may cause undesired operation.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
European Union
This equipment complies with the following requirements of the EMC Directive 2004/108/EC:
As Information Technology Equipment (ITE) Class A per (as applicable):
EN 55022:2006
EN 61000-3-2:2000 +A2:2005
EN 61000-3-3:1995 +A1:2001
Class A
Pass
Pass
EN 55024:1998 +A1:2001 +A2:2003 Required Limits:
IEC61000-4-2
IEC61000-4-3
IEC61000-4-4
IEC61000-4-5
IEC61000-4-6
IEC61000-4-8
IEC61000-4-11
4 kV (Direct), 8 kV (Air)
3 V/m
1 kV AC Power Lines, 0.5 kV Signal and DC Power Lines
1 kV AC Line-Line and Outdoor Signal Lines, 2 kV AC Line-Gnd, 0.5 kV DC Power Lines
3 V
1 A/m
Pass
Safety
This equipment complies with the following requirements of the Low Voltage Directive 2006/95/EC:
EC Type Examination Certificates:
EN 60950-1:2001, 1st Edition
IEC 60950-1:2001, 1st Edition
Evaluated to all CB Countries
UL 60950-1:2003, CSA C22.2 No. 60950-03
File: E157779-A10-UL-1
Supplementary Information
This product was tested and complies with all the requirements for the CE Mark. This equipment complies with the
Restriction of Hazardous Substances (RoHS) directive 2002/95/EC.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
.
/S/
/S/
Dennis P. Symanski
DATE
Donald Cameron
DATE
Worldwide Compliance Office
Sun Microsystems, Inc.
4150 Network Circle, MPK15-102
Santa Clara, CA 95054 U.S.A.
Tel: 650-786-3255
Program Manager/Quality Systems
Sun Microsystems Scotland, Limited
Blackness Road, Phase I, Main Bldg.
Springfield, EH49 7LR
Scotland, United Kingdom
Fax: 650-786-3723
Tel: +44 1 506 672 539
Fax: +44 1 506 670 011
vi
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Statements
Your Sun product is marked to indicate its compliance class:
•
•
•
•
Federal Communications Commission (FCC) — USA
Industry Canada Equipment Standard for Digital Equipment (ICES-003) — Canada
Voluntary Control Council for Interference (VCCI) — Japan
Bureau of Standards Metrology and Inspection (BSMI) — Taiwan
Please read the appropriate section that corresponds to the marking on your Sun product before attempting to install the
product.
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is
not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required
to correct the interference at his own expense.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the authority
granted to the user by the FCC to operate this equipment.
ICES-003 Class A Notice - Avis NMB-003, Classe A
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
BSMI Class A Notice
The following statement is applicable to products shipped to Taiwan and marked as Class A on the product compliance
label.
CCC Class A Notice
The following statement is applicable to products shipped to China and marked with “Class A” on the product’s compliance
label.
GOST-R Certification Mark
viii Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Statements
Download from Www.Somanuals.com. All Manuals Search And Download.
ix
x
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the type of power switch your device has,
one of the following symbols may be used:
Safety Agency Compliance
Statements
Read this section before beginning any procedure. The
following text provides safety precautions to follow when
installing a Sun Microsystems product.
On – Applies AC power to the system.
Off – Removes AC power from the system.
Safety Precautions
For your protection, observe the following safety
precautions when setting up your equipment:
Standby – The On/Standby switch is in the
standby position.
■
■
Follow all cautions and instructions marked on the
equipment.
Modifications to Equipment
Do not make mechanical or electrical modifications to the
equipment. Sun Microsystems is not responsible for
regulatory compliance of a modified Sun product.
Ensure that the voltage and frequency of your power
source match the voltage and frequency inscribed on
the equipment’s electrical rating label.
■
Never push objects of any kind through openings in
the equipment. Dangerous voltages may be present.
Conductive foreign objects could produce a short
circuit that could cause fire, electric shock, or damage
to your equipment.
Placement of a Sun Product
Caution – Do not block or cover the openings
of your Sun product. Never place a Sun
product near a radiator or heat register.
Failure to follow these guidelines can cause
overheating and affect the reliability of your
Sun product.
Symbols
The following symbols may appear in this book:
Caution – There is a risk of personal injury
and equipment damage. Follow the
instructions.
■
Product: Sun StorageTek 8 Gb FC PCI-Express HBA,
Emulex
In compliance with the requirements defined in ISO 7779,
the workplace-dependent noise level of this product is less
than 70 db (A).
Caution – Hot surface. Avoid contact.
Surfaces are hot and may cause personal
injury if touched.
In compliance with the requirements defined in ISO 7779,
the workplace-dependent noise level of this product is
XX db(A).
Caution – Hazardous voltages are present. To
reduce the risk of electric shock and danger to
personal health, follow the instructions.
SELV Compliance
Safety status of I/O connections comply to SELV
requirements.
Power Cord Connection
Caution – Sun products are designed to work
with power systems having a grounded
neutral (grounded return for DC-powered
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
products). To reduce the risk of electric shock,
do not plug Sun products into any other type
of power system. Contact your facilities
manager or a qualified electrician if you are
not sure what type of power is supplied to
your building.
The following caution applies only to devices with a
Standby power switch:
Caution – The power switch of this product
functions as a standby type device only. The
power cord serves as the primary disconnect
device for the system. Be sure to plug the
power cord into a grounded power outlet that
is nearby the system and is readily accessible.
Do not connect the power cord when the
power supply has been removed from the
system chassis.
Caution – Not all power cords have the same
current ratings. Do not use the power cord
provided with your equipment for any other
products or use. Household extension cords
do not have overload protection and are not
meant for use with computer systems. Do not
use household extension cords with your Sun
product.
The following caution applies only to devices with multiple
power cords:
Caution – For products with multiple power
cords, all power cords must be disconnected
to completely remove power from the system.
Battery Warning
Caution – There is danger of explosion if
batteries are mishandled or incorrectly
replaced. On systems with replaceable
batteries, replace only with the same
manufacturer and type or equivalent type
recommended by the manufacturer per the
instructions provided in the product service
manual. Do not disassemble batteries or
attempt to recharge them outside the system.
Do not dispose of batteries in fire. Dispose of
batteries properly in accordance with the
manufacturer’s instructions and local
regulations. Note that on Sun CPU boards,
there is a lithium battery molded into the real-
time clock. These batteries are not customer
replaceable parts.
xii
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
System Unit Cover
Laser Compliance Notice
You must remove the cover of your Sun computer system
unit to add cards, memory, or internal storage devices. Be
sure to replace the cover before powering on your computer
system.
Sun products that use laser technology comply with Class 1
laser requirements.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Caution – Do not operate Sun products
without the cover in place. Failure to take this
precaution may result in personal injury and
system damage.
Rack System Warning
CD and DVD Devices
The following warnings apply to Racks and Rack Mounted
The following caution applies to CD, DVD, and other
systems.
optical devices.
Caution – For safety, equipment should
always be loaded from the bottom up. That is,
install the equipment that will be mounted in
the lowest part of the rack first, then the next
higher systems, etc.
Caution – Use of controls, adjustments, or
the performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
Conformité aux normes de sécurité
Caution – To prevent the rack from tipping
during equipment installation, the anti-tilt bar
on the rack must be deployed.
Veuillez lire attentivement cette section avant de
commencer. Ce texte traite des mesures de sécurité qu’il
convient de prendre pour l’installation d’un produit Sun
Microsystems.
Caution – To prevent extreme operating
temperature within the rack insure that the
maximum temperature does not exceed the
product’s ambient rated temperatures.
Mesures de sécurité
Pour votre sécurité, nous vous recommandons de suivre
scrupuleusement les mesures de sécurité ci-dessous lorsque
vous installez votre matériel:
■
Suivez tous les avertissements et toutes les
instructions inscrites sur le matériel.
Caution – To prevent extreme operating
temperatures due to reduced airflow
consideration should be made to the amount
of air flow that is required for a safe operation
of the equipment.
■
Assurez-vous que la tension et la fréquence de votre
source d'alimentation correspondent à la tension et à
la fréquence indiquées sur l'étiquette de la tension
électrique nominale du matériel
■
N'introduisez jamais d'objets quels qu'ils soient dans
les ouvertures de l'équipement. Vous pourriez vous
trouver en présence de hautes tensions dangereuses.
Tout objet étranger conducteur risque de produire un
court-circuit pouvant présenter un risque d'incendie
ou de décharge électrique, ou susceptible
d'endommager le matériel.
Safety Agency Compliance Statements xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Symboles
Positionnement d’un produit Sun
Vous trouverez ci-dessous la signification des différents
symboles utilisés:
Attention – Evitez d'obstruer ou de recouvrir
les orifices de votre produit Sun. N'installez
jamais un produit Sun près d'un radiateur ou
d'une source de chaleur. Si vous ne respectez
pas ces consignes, votre produit Sun risque de
surchauffer et son fonctionnement en sera
altéré.
Attention – Vous risquez d'endommager le
matériel ou de vous blesser. Veuillez suivre les
instructions.
Attention – Surfaces brûlantes. Evitez tout
contact. Les surfaces sont brûlantes. Vous
risquez de vous blesser si vous les touchez.
Niveau de pression acoustique
Produit : Sun StorageTek 8 Gb FC PCI-Express HBA,
Emulex
Conformément à la norme ISO 7779, le niveau sonore de ce
produit sur le lieu de travail est inférieur à 70 db(A).
Attention – Tensions dangereuses. Pour
réduire les risques de décharge électrique et
de danger physique, observez les consignes
indiquées.
Conformément à la norme ISO 7779, le niveau sonore de ce
produit sur le lieu de travail est de XX db(A).
Selon le type d'interrupteur marche/arrêt dont votre
appareil est équipé, l'un des symboles suivants sera utilisé:
Conformité SELV
Le niveau de sécurité des connexions E/S est conforme aux
normes SELV.
Marche – Met le système sous tension
alternative.
Connexion du cordon d’alimentation
Attention – Les produits Sun sont conçus
pour fonctionner avec des systèmes
d'alimentation équipés d'un conducteur
neutre relié à la terre (conducteur neutre pour
produits alimentés en CC). Pour réduire les
risques de décharge électrique, ne branchez
jamais les produits Sun sur une source
d'alimentation d'un autre type. Contactez le
gérant de votre bâtiment ou un électricien
agréé si vous avez le moindre doute quant au
type d'alimentation fourni dans votre
bâtiment.
Arret – Met le système hors tension
alternative.
Veilleuse – L'interrupteur Marche/Veille est
sur la position de veille.
Modification du matériel
N'apportez aucune modification mécanique ou électrique
au matériel. Sun Microsystems décline toute responsabilité
quant à la non-conformité éventuelle d'un produit Sun
modifié.
Attention – Tous les cordons d'alimentation
ne présentent pas les mêmes caractéristiques
électriques. Les cordons d'alimentation à
usage domestique ne sont pas protégés contre
les surtensions et ne sont pas conçus pour être
xiv Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
utilisés avec des ordinateurs. N'utilisez jamais
de cordon d'alimentation à usage domestique
avec les produits Sun.
Couvercle de l'unité
Pour ajouter des cartes, de la mémoire ou des périphériques
de stockage internes, vous devez retirer le couvercle de
votre système Sun. Remettez le couvercle supérieur en
place avant de mettre votre système sous tension.
L'avertissement suivant s'applique uniquement aux
systèmes équipés d'un interrupteur Veille:
Attention – Ne mettez jamais des produits
Sun sous tension si leur couvercle supérieur
n'est pas mis en place. Si vous ne prenez pas
ces précautions, vous risquez de vous blesser
ou d'endommager le système.
Attention – L'interrupteur d'alimentation de
ce produit fonctionne uniquement comme un
dispositif de mise en veille. Le cordon
d'alimentation constitue le moyen principal de
déconnexion de l'alimentation pour le
système. Assurez-vous de le brancher dans
une prise d'alimentation mise à la terre près
du système et facile d'accès. Ne le branchez
pas lorsque l'alimentation électrique ne se
trouve pas dans le châssis du système.
Mise en garde relative au système en rack
La mise en garde suivante s'applique aux racks et aux
systèmes montés en rack.
Attention – Pour des raisons de sécurité, le
matériel doit toujours être chargé du bas vers
le haut. En d'autres termes, vous devez
installer, en premier, le matériel qui doit se
trouver dans la partie la plus inférieure du
rack, puis installer le matériel sur le niveau
suivant, etc.
L'avertissement suivant s'applique uniquement aux
systèmes équipés de plusieurs cordons d'alimentation:
Attention – Pour mettre un système équipé
de plusieurs cordons d'alimentation hors
tension, il est nécessaire de débrancher tous
les cordons d'alimentation.
Attention – Afin d'éviter que le rack ne
penche pendant l'installation du matériel, tirez
la barre anti-basculement du rack.
Mise en garde relative aux batteries
Attention – Les batteries risquent d’exploser
en cas de manipulation maladroite ou de
remplacement incorrect. Pour les systèmes
dont les batteries sont remplaçables, effectuez
les remplacements uniquement selon le
modèle du fabricant ou un modèle équivalent
recommandé par le fabricant, conformément
aux instructions fournies dans le manuel de
service du système. N’essayez en aucun cas de
démonter les batteries, ni de les recharger hors
du système. Ne les jetez pas au feu. Mettez-les
au rebut selon les instructions du fabricant et
conformément à la législation locale en
Attention – Pour éviter des températures de
fonctionnement extrêmes dans le rack,
assurez-vous que la température maximale ne
dépasse pas la fourchette de températures
ambiantes du produit déterminée par le
fabricant.
Attention – Afin d'empêcher des
températures de fonctionnement extrêmes
provoquées par une aération insuffisante,
assurez-vous de fournir une aération
appropriée pour un fonctionnement du
matériel en toute sécurité
vigueur. Notez que sur les cartes processeur
de Sun, une batterie au lithium a été moulée
dans l'horloge temps réel. Les batteries ne sont
pas des pièces remplaçables par le client.
Safety Agency Compliance Statements
Download from Www.Somanuals.com. All Manuals Search And Download.
xv
Avis de conformité des appareils laser
Symbole
Les produits Sun qui font appel aux technologies lasers sont
Die Symbole in diesem Handbuch haben folgende
conformes aux normes de la classe 1 en la matière.
Bedeutung:
Achtung – Gefahr von Verletzung und
Geräteschaden. Befolgen Sie die Anwei-
sungen.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Achtung – Heiße Oberfläche. Nicht berühren,
da Verletzungsgefahr durch heiße Oberfläche
besteht.
Périphériques CD et DVD
L'avertissement suivant s'applique aux périphériques CD,
DVD et autres périphériques optiques:
Achtung – Gefährliche Spannungen.
Befolgen Sie die Anweisungen, um
Stromschläge und Verletzungen zu vermeiden.
Attention – L'utilisation de contrôles et de
réglages ou l'application de procédures autres
que ceux spécifiés dans le présent document
peuvent entraîner une exposition à des
radiations dangereuses.
Je nach Netzschaltertyp an Ihrem Gerät kann eines der
folgenden Symbole verwendet werden:
Ein – Versorgt das System mit Wechselstrom.
Einhaltung sicherheitsbehördlicher
Vorschriften
Lesen Sie vor dem Ausführen von Arbeiten diesen
Abschnitt. Im folgenden Text werden Sicherheitsvor-
kehrungen beschrieben, die Sie bei der Installation eines
Sun Microsystems-Produkts beachten müssen.
Aus– Unterbricht die Wechselstromzufuhr
zum Gerät.
Wartezustand – Der Ein-/Standby-Netz-
schalter befindet sich in der Standby-Position.
Sicherheitsvorkehrungen
Treffen Sie zu Ihrem eigenen Schutz bei der Installation des
Geräts die folgenden Sicherheitsvorkehrungen:
Modifikationen des Geräts
Nehmen Sie keine elektrischen oder mechanischen
Gerätemodifikationen vor. Sun Microsystems ist für die
Einhaltung der Sicherheitsvorschriften von modifizierten
Sun-Produkten nicht haftbar.
■
■
Beachten Sie alle auf den Geräten angebrachten
Warnhinweise und Anweisungen.
Stellen Sie sicher, dass Spannung und Frequenz der
Stromversorgung den Nennleistungen auf dem am
Gerät angebrachten Etikett entsprechen.
Aufstellung von Sun-Geräten
■
Führen Sie niemals Fremdobjekte in die Öffnungen
am Gerät ein. Es können gefährliche Spannungen
anliegen. Leitfähige Fremdobjekte können einen
Kurzschluss verursachen, der einen Brand, Strom-
schlag oder Geräteschaden herbeiführen kann.
Achtung – Geräteöffnungen Ihres Sun-
Produkts dürfen nicht blockiert oder
abgedeckt werden. Sun-Geräte sollten niemals
in der Nähe von Heizkörpern oder Heißluft-
klappen aufgestellt werden. Die Nichtbeach-
xvi Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
tung dieser Richtlinien kann Überhitzung
verursachen und die Zuverlässigkeit Ihres
Sun-Geräts beeinträchtigen.
Achtung – Beim Netzschalter dieses Geräts
handelt es sich nur um einen Ein/Standby-
Schalter. Zum völligen Abtrennen des Systems
von der Stromversorgung dient hauptsächlich
das Netzkabel. Stellen Sie sicher, dass das
Netzkabel an eine frei zugängliche geerdete
Steckdose in der Nähe des Systems ange-
schlossen ist. Schließen Sie das Stromkabel
nicht an, wenn die Stromversorgung vom
Systemchassis entfernt wurde.
Lautstärke
Produkt: Sun StorageTek 8 Gb FC PCI-Express HBA,
Emulex
Gemäß den Vorgaben in der Norm ISO 7779 beträgt der
Geräuschpegel dieses Geräts in Abhängigkeit vom
Arbeitsplatz unter 70 db(A).
Die folgende Warnung gilt nur für Geräte mit mehreren
Netzkabeln:
Gemäß den Vorgaben in der Norm ISO 7779 beträgt der
Geräuschpegel dieses Geräts in Abhängigkeit vom
Arbeitsplatz XX db(A).
Achtung – Bei Produkten mit mehreren
Netz-kabeln müssen alle Netzkabel abgetrennt
wer-den, um das System völlig von der
Stromver-sorgung zu trennen.
SELV-Konformität
Der Sicherheitsstatus der E/A-Verbindungen entspricht
den SELV-Anforderungen.
Anschluss des Netzkabels
Warnung bezüglich Batterien
Achtung – Sun-Geräte sind für
Achtung – Bei unsachgemäßer Handhabung
oder nicht fachgerechtem Austausch der
Batterien besteht Explosionsgefahr. Verwen-
den Sie bei Systemen mit austauschbaren
Batterien ausschließlich Ersatzbatterien
desselben Typs und Herstellers bzw. einen
entsprechenden, vom Hersteller gemäß den
Anweisungen im Service-Handbuch des
Produkts empfohlenen Batterietyp. Versuchen
Sie nicht, die Batterien auszubauen oder
außerhalb des Systems wiederaufzuladen.
Werfen Sie die Batterien nicht ins Feuer.
Entsorgen Sie die Batterien entsprechend den
Anweisungen des Herstellers und den vor Ort
geltenden Vorschriften. CPU-Karten von Sun
verfügen über eine Echtzeituhr mit integrier-
ter Lithiumbatterie. Diese Batterie darf nur
von einem qualifizierten Servicetechniker aus-
gewechselt werden.
Stromversorgungssysteme mit einem
geerdeten neutralen Leiter (geerdeter
Rückleiter bei gleichstrombetriebenen
Geräten) ausgelegt. Um die Gefahr von
Stromschlägen zu vermeiden, schließen Sie
das Gerät niemals an andere Stromversor-
gungssysteme an. Wenden Sie sich an den
zuständigen Gebäudeverwalter oder an einen
qualifizierten Elektriker, wenn Sie nicht sicher
wissen, an welche Art von Stromversor-
gungssystem Ihr Gebäude angeschlossen ist.
Achtung – Nicht alle Netzkabel verfügen
über die gleichen Nennwerte. Herkömmliche,
im Haushalt verwendete Verlängerungskabel
besitzen keinen Überlastschutz und sind
daher für Computersysteme nicht geeignet.
Verwenden Sie bei Ihrem Sun-Produkt keine
Haushalts-Verlängerungskabel.
Gehäuseabdeckung
Die folgende Warnung gilt nur für Geräte mit Standby-
Netzschalter:
Sie müssen die Abdeckung Ihres Sun-Computersystems
entfernen, um Karten, Speicher oder interne Speichergeräte
hinzuzufügen. Bringen Sie vor dem Einschalten des
Systems die Gehäuseabdeckung wieder an.
Safety Agency Compliance Statements xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Achtung – Nehmen Sie Sun-Geräte nicht
ohne Abdeckung in Betrieb. Die
Nichtbeachtung dieses Warnhinweises kann
Verletzungen oder Geräteschaden zur Folge
haben.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Warnungen bezüglich in Racks eingebauter
Systeme
Die folgenden Warnungen gelten für Racks und in Racks
CD- und DVD-Geräte
Die folgende Warnung gilt für CD-, DVD- und andere
optische Geräte:
eingebaute Systeme:
Achtung – Die hier nicht aufgeführte
Verwendung von Steuerelementen,
Anpassungen oder Ausführung von
Vorgängen kann eine gefährliche
Strahlenbelastung verursachen.
Achtung – Aus Sicherheitsgründen sollten
sämtliche Geräte von unten nach oben in
Racks eingebaut werden. Installieren Sie also
zuerst die Geräte, die an der untersten
Position im Rack eingebaut werden, gefolgt
von den Systemen, die an nächsthöherer Stelle
eingebaut werden, usw.
Normativas de seguridad
Lea esta sección antes de realizar cualquier operación. En
ella se explican las medidas de seguridad que debe tomar al
instalar un producto de Sun Microsystems.
Achtung – Verwenden Sie beim Einbau den
Kippschutz am Rack, um ein Umkippen zu
vermeiden.
Medidas de seguridad
Para su protección, tome las medidas de seguridad
Achtung – Um extreme
Betriebstemperaturen im Rack zu vermeiden,
stellen Sie sicher, dass die Maximaltemperatur
die Nennleistung der Umgebungstemperatur
für das Produkt nicht überschreitet
siguientes durante la instalación del equipo:
■
■
Siga todos los avisos e instrucciones indicados en el
equipo.
Asegúrese de que el voltaje y frecuencia de la fuente
de alimentación coincidan con el voltaje y frecuencia
indicados en la etiqueta de clasificación eléctrica del
equipo.
Achtung – Um extreme
Betriebstemperaturen durch verringerte
Luftzirkulation zu vermei-den, sollte die für
den sicheren Betrieb des Geräts erforderliche
Luftzirkulation eingesetzt werden.
■
No introduzca objetos de ningún tipo por las rejillas
del equipo, ya que puede quedar expuesto a voltajes
peligrosos. Los objetos conductores extraños pueden
producir cortocircuitos y, en consecuencia, incendios,
descargas eléctricas o daños en el equipo.
Símbolos
Hinweis zur Laser-Konformität
En este documento aparecen los siguientes símbolos:
Sun-Produkte, die die Laser-Technologie verwenden,
entsprechen den Laser-Anforderungen der Klasse 1.
Precaución – Existe el riesgo de que se
produzcan lesiones personales y daños en el
equipo. Siga las instrucciones.
xviii Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
En conformidad con la norma ISO 7779, el nivel de emisión
de ruido de este producto en el puesto de trabajo es inferior
a los 70 db(A).
Precaución – Superficie caliente. Evite todo
contacto. Las superficies están calientes y
pueden causar lesiones personales si se tocan.
En conformidad con la norma ISO 7779, el nivel de emisión
de ruido de este producto en el puesto de trabajo es de
XX db(A).
Precaución – Voltaje peligroso. Para reducir
el riesgo de descargas eléctricas y lesiones
personales, siga las instrucciones.
Cumplimiento de la normativa para
instalaciones SELV
Las condiciones de seguridad de las conexiones de entrada
y salida cumplen los requisitos para instalaciones SELV (del
inglés Safe Extra Low Voltage, voltaje bajo y seguro).
En función del tipo de interruptor de alimentación del que
disponga el dispositivo, se utilizará uno de los símbolos
siguientes:
Conexión del cable de alimentación
Encendido – Suministra alimentación de CA
al sistema.
Precaución – Los productos Sun se han
diseñado para funcionar con sistemas de
alimentación que cuenten con un conductor
neutro a tierra (con conexión a tierra de
regreso para los productos con alimentación
de CC). Para reducir el riesgo de descargas
eléctricas, no conecte ningún producto Sun a
otro tipo de sistema de alimentación. Póngase
en contacto con el encargado de las
Apagado – Corta la alimentación de CA del
sistema.
Espera – El interruptor de encendido/espera
está en la posición de espera.
instalaciones de su empresa o con un
electricista cualificado en caso de que no esté
seguro del tipo de alimentación del que se
dispone en el edificio.
Modificaciones en el equipo
No realice modificaciones de tipo mecánico ni eléctrico en el
equipo. Sun Microsystems no se hace responsable del
cumplimiento de normativas en caso de que un producto
Sun se haya modificado.
Precaución – No todos los cables de
alimentación tienen la misma clasificación
eléctrica. Los alargadores de uso doméstico no
cuentan con protección frente a sobrecargas y
no están diseñados para su utilización con
sistemas informáticos. No utilice alargadores
de uso doméstico con el producto Sun.
Colocación de un producto Sun
Precaución – No obstruya ni tape las rejillas
del producto Sun. Nunca coloque un producto
Sun cerca de radiadores ni fuentes de calor. Si
no sigue estas indicaciones, el producto Sun
podría sobrecalentarse y la fiabilidad de su
funcionamiento se vería afectada.
La siguiente medida solamente se aplica a aquellos
dispositivos que dispongan de un interruptor de
alimentación de espera:
Precaución – El interruptor de alimentación
de este producto funciona solamente como un
dispositivo de espera. El cable de alimentación
hace las veces de dispositivo de desconexión
principal del sistema. Asegúrese de que
Nivel de ruido
Producto: Sun StorageTek 8 Gb FC PCI-Express HBA,
Emulex
conecta el cable de alimentación a una toma
Safety Agency Compliance Statements xix
Download from Www.Somanuals.com. All Manuals Search And Download.
de tierra situada cerca del sistema y de fácil
acceso. No conecte el cable de alimentación si
la unidad de alimentación no se encuentra en
el bastidor del sistema.
Advertencia sobre el sistema en bastidor
Las advertencias siguientes se aplican a los sistemas
montados en bastidor y a los propios bastidores.
Precaución – Por seguridad, siempre deben
montarse los equipos de abajo arriba. A saber,
primero debe instalarse el equipo que se
situará en el bastidor inferior; a continuación,
el que se situará en el siguiente nivel, etc.
La siguiente medida solamente se aplica a aquellos
dispositivos que dispongan de varios cables de
alimentación:
Precaución – En los productos que cuentan
con varios cables de alimentación, debe
desconectar todos los cables de alimentación
para cortar por completo la alimentación
eléctrica del sistema.
Precaución – Para evitar que el bastidor se
vuelque durante la instalación del equipo,
debe extenderse la barra antivolcado del
bastidor.
Advertencia sobre las baterías
Precaución – Para evitar que se alcance una
temperatura de funcionamiento extrema en el
bastidor, asegúrese de que la temperatura
máxima no sea superior a la temperatura
ambiente establecida como adecuada para el
producto.
Precaución – Si las baterías no se manipulan
o reemplazan correctamente, se corre el riesgo
de que estallen. En los sistemas que cuentan
con baterías reemplazables, reemplácelas sólo
con baterías del mismo fabricante y el mismo
tipo, o un tipo equivalente recomendado por
el fabricante, de acuerdo con las instrucciones
descritas en el manual de servicio del
producto. No desmonte las baterías ni intente
recargarlas fuera del sistema. No intente
deshacerse de las baterías echándolas al fuego.
Deshágase de las baterías correctamente de
acuerdo con las instrucciones del fabricante y
las normas locales. Tenga en cuenta que en las
placas CPU de Sun, hay una batería de litio
incorporada en el reloj en tiempo real. Los
usuarios no deben reemplazar este tipo de
baterías.
Precaución – Para evitar que se alcance una
temperatura de funcionamiento extrema
debido a una circulación de aire reducida,
debe considerarse la magnitud de la
circulación de aire requerida para que el
equipo funcione de forma segura.
Aviso de cumplimiento de la normativa para
la utilización de láser
Los productos Sun que utilizan tecnología láser cumplen los
requisitos establecidos para los productos láser de clase 1.
Cubierta de la unidad del sistema
Debe extraer la cubierta de la unidad del sistema
informático Sun para instalar tarjetas, memoria o
dispositivos de almacenamiento internos. Vuelva a colocar
la cubierta antes de encender el sistema informático.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Precaución – No ponga en funcionamiento
los productos Sun que no tengan colocada la
cubierta. De lo contrario, puede sufrir lesiones
personales y ocasionar daños en el sistema.
xx
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Dispositivos de CD y DVD
La siguiente medida se aplica a los dispositivos de CD y
Nordic Power Distribution Cautions
DVD, así como a otros dispositivos ópticos:
English
Precaución – La utilización de controles,
ajustes o procedimientos distintos a los aquí
especificados puede dar lugar a niveles de
radiación peligrosos.
Caution – This product is also designed for
an IT power distribution system with phase-
to-phase voltage of 230V.
Danmark
Nordic Lithium Battery Cautions
Advarsel! – Dette produkt er også beregnet til
et IT-strømfordelingssystem med en fase-til-
fase spænding på 230 V.
Norge
Advarsel – Litiumbatteri — Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten. Brukt batteri
returneres apparatleverandøren.
Nordic Grounded Socket Cautions
English
Sverige
Caution – The appliance must be connected to
a grounded socket.
Varning – Explosionsfara vid felaktigt
batteribyte. Använd samma batterityp eller en
ekvivalent typ som rekommenderas av
apparattillverkaren. Kassera använt batteri
enligt fabrikantens instruktion.
Norge
Advarsel – Apparatet må tilkoples jordet
stikkontakt.
Danmark
Sverige
Advarsel! – Litiumbatteri — Eksplosionsfare
ved fejlagtig håndtering. Udskiftning må kun
ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til
leverandøren.
Varning – Apparaten skall anslutas till jordat
uttag.
Suomi
Suomi
Varoitus – Laite on liitettävä
suojamaadoituskoskettimilla varustettuun
pistorasiaan.
Varoitus – Paristo voi räjähtää, jos se on
virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.
Safety Agency Compliance Statements xxi
Download from Www.Somanuals.com. All Manuals Search And Download.
xxii Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This installation guide describes how to install and remove the single and dual port
Sun StorageTek™ 8 Gigabit (Gb) Fibre Channel (FC) PCI-Express module host bus
adapter (HBA). It also explains how to install the driver and any other utilities
required by the HBA. The document is written for technicians, system
administrators, application service providers (ASPs), and users who have advanced
experience troubleshooting and replacing hardware.
Before You Read This Book
Before you install and use the HBA as described in this document, read and
understand the following documents.
■
SunVTS 6.X Users Guide
■
SunVTS 6.X Reference Manual
How This Book Is Organized
Chapter 1 provides an overview of the product and lists the various operating
systems, host platforms, switches, and storage systems, that support the HBA.
Chapter 2 describes how to install and remove the HBA.
Chapter 3 describes how to install any software and utilities that are required by the
HBA.
xxiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 contains known issues with the HBA.
Using UNIX Commands
This document might not contain information about basic UNIX commands and
procedures such as shutting down the system, booting the system, and configuring
devices. Refer to the following for this information:
®
■
Software documentation that you received with your system
Solaris™ Operating System documentation, which is at:
■
Shell Prompts
Shell
Prompt
C shell
machine-name%
C shell superuser
machine-name#
Bourne shell and Korn shell
Bourne shell and Korn shell superuser
$
#
xxiv Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Typographic Conventions
Typeface
Meaning
Examples
AaBbCc123
The names of commands, files,
and directories; on-screen
computer output.
Edit your.loginfile.
Use ls -ato list all files.
% You have mail.
AaBbCc123
What you type, when contrasted % su
with on-screen computer output.
Password:
Book titles, new words or terms, Read Chapter 6 in the User’s Guide.
AaBbCc123
words to be emphasized.
Replace command-line variables
with real names or values.
These are called class options.
You must be superuser to do this.
To delete a file, type rmfilename.
Note – Characters display differently depending on browser settings. If characters
do not display correctly, change the character encoding in your browser to Unicode
UTF-8.
Documentation, Support, and Training
Sun Function
Documentation
Support
URL
Training
Preface
xxv
Download from Www.Somanuals.com. All Manuals Search And Download.
Third-Party Web Sites
Sun is not responsible for the availability of third-party web sites mentioned in this
document. Sun does not endorse and is not responsible or liable for any content,
advertising, products, or other materials that are available on or through such sites
or resources. Sun will not be responsible or liable for any actual or alleged damage
or loss caused by or in connection with the use of or reliance on any such content,
goods, or services that are available on or through such sites or resources.
Sun Welcomes Your Comments
Sun is interested in improving its documentation and welcomes your comments and
suggestions. You can submit your comments by going to:
Please include the title and part number of your document with your feedback:
Sun StorageTek™ 8 Gb FC PCI-Express HBA, Emulex Installation Guide, part number
820-5465-12
xxvi Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
1
HBA Overview
This chapter provides a basic overview of the single and dual port Sun StorageTek™
8 Gb Fibre Channel (FC) PCI-Express host bus adapter (HBA), Emulex (referred to as
platforms, storage, and infrastructure configurations that support the HBA and lists
the HBA environmental requirements.
This chapter contains the following topics:
■
■
■
■
■
■
“Kit Contents” on page 1
“HBA Features and Specifications” on page 2
“System Interoperability” on page 4
“Operating System and Technology Requirements” on page 3
“System Interoperability” on page 4
“Environmental Requirements” on page 7
Kit Contents
■
■
■
■
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex
Extra PCI full-size bracket
Accessing Documentation document (part number: 820-2299-xx)
P002403-05A China RoHS Material disclosure
1
Download from Www.Somanuals.com. All Manuals Search And Download.
HBA Features and Specifications
EM8-Z, dual port: SG-XPCIE2FC-EM8-Z) consists of a single-wide, FC bus expansion
board. The board interfaces a four- or eight-lane PCI-Express bus, with the four or
eight lanes supporting one or two Fibre Channel (FC) optical media ports. Each
independent FC port operates at 8 Gbit/sec and features 8/4/2 autonegotiation.
See TABLE 1-1 for a list of the HBA features.
TABLE 1-1
Feature
HBA Features and Specifications
Description
PCIconnector
x8
PCI signaling environment PCI Express x8 (8 active lanes)
PCI lane usage
x8 lanes
PCItransfer rate
(maximum)
PCI Express Generation One (GT/s) x8
PCI Express Generation Two (5.0 GT/s) x8
Number of FC ports
One (single port) or Two (dual port)
Number of devices
supported
126 devices per FC loop; 510 devices in Fabric mode
FC bus type (external)
FC transfer rate
Fiber-optic media, short-wave, multi-mode fiber (400-M5- SN-S)
400 MBps per port maximum, half-duplex
800 MBps per port maximum, full-duplex
FC topologies
RAM
Switched fabric (N-Port), arbitrated loop (NL-Port), and point-to-point (N-Port)
1.5 MB, parity protected, per port
BIOS ROM (FC)
NVRAM
One 4-MB (dual-port) or 2-MB (single-port) flash ROM
One 2-KB EEPROM per port
External connectors
One Small-Form Factor Pluggable (SFP) multimode optic with LC-style
connectors per port
2
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 1-1
HBA Features and Specifications
Feature (Continued)
Description (Continued)
Maximum FC cable length 2 Gb/s: 500 meters using 50/125 µm core OM3 fiber
300 meters using 50/125 µm core OM2 fiber
150 meters using 62.5/125 µm core OM1 fiber
4 Gb/s: 380 meters using 50/125 µm core OM3 fiber
150 meters using 50/125 µm core OM2 fiber
70 meters using 62.5/125 µm core OM1 fiber
8 Gb/s: 150 meters using 50/125 µm core OM3 fiber
50 meters using 50/125 µm core OM2 fiber
21 meters using 62.5/125 µm core OM1 fiber
LED indicators
Two LEDs per port (yellow and green) on the front panel as status indicators.
Maximum power
consumption
13.3W (dual port), 10.1W (signal port)
Form Factor
Low-profile MD2 form factor
Operating System and Technology
Requirements
The HBA requires the OS and technology levels listed in TABLE 1-2.
TABLE 1-2
Operating System/Technology
Supported Operating System/Technology Versions
Supported Versions
Solaris 10 OS for the x64 and x86
(32-bit and 64-bit) platforms
(Supports MPXIO)
• Solaris 10 8/07 (all updates)
Solaris 10 OS for the SPARC (64-bit) • Solaris 10 (all updates)
platform (Supports MPXIO)
Linux OS
• Red Hat Enterprise Linux 4.6 (32-bit and 64-bit), U5
• Red Hat Enterprise Linux 5.1 (32-bit and 64-bit), U1
• SUSE Linux Enterprise Server 9 (32-bit and 64-bit), SP4
• SUSE Linux Enterprise Server 10 (32-bit and 64-bit), SP1
Chapter 1 HBA Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
3
TABLE 1-2
Supported Operating System/Technology Versions (Continued)
Operating System/Technology
Supported Versions
Microsoft Windows OS Enterprise
and Standard Editions
WHQL Certified, MS Windows
MPIO
• Windows Server 2003 SP1 32-bit, x64
• Windows Server 2003 SP2 32-bit, x64
• Windows Server 2003 SP1/R2 32-bit, x64
• Windows Server 2003 SP2/R2 32-bit, x64
Microsoft Windows OS Enterprise
and Standard Editions
WHQL Certified, MS Windows
MPIO
• Windows Server 2008 32-bit, x64
VMware Technology
• ESX Server 3.5 u2
compatible with the heterogeneous FC network design of the HBA. This section
contains the following topics:
■
■
■
“Host Platform Support” on page 4
“Storage Support” on page 5
“Quantum S4 tape drive” on page 6
Host Platform Support
The HBA is supported by the platforms listed in TABLE 1-3.
TABLE 1-3
Platform
Platform Support
Supported OS/Technology
Sun SPARC Servers
Sun SPARC Enterprise T2000
Sun SPARC Enterprise T5120
Sun SPARC Enterprise T5140
Sun SPARC Enterprise T5220
Sun SPARC Enterprise T5240
Sun SPARC Enterprise T5440
Solaris
Solaris
Solaris
Solaris
Solaris
Solaris
4
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 1-3
Platform Support (Continued)
Platform (Continued)
Supported OS/Technology (Continued)
Sun SPARC Enterprise M4000
Sun SPARC Enterprise M5000
Sun SPARC Enterprise M8000
Sun SPARC Enterprise M9000-32
Sun SPARC Enterprise M9000-64
Sun Fire™ V445
Solaris
Solaris
Solaris
Solaris
Solaris
Solaris
Solaris
Solaris
Sun Fire V245
Sun Ultra U45
Sun x64 AMD Servers
Sun Fire X4100M2
Sun Fire X4200M2
Sun Fire X4600
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
Sun Fire X4600M2
Sun Fire X4440
Sun Fire X4240
Sun Fire X4140
Sun Fire X2100M2
Sun Fire X2200M2
Sun x64 Intel Servers
Sun Fire X4150
Sun Fire X4450
Solaris, Windows, Linux, VMware
Solaris, Windows, Linux, VMware
The host system must have at least one PCI-Express 8-lane slot to support the HBA.
contains the following topics:
■
■
■
■
“Array Support” on page 6
“System Support” on page 6
“Tape Storage Support” on page 6
“Quantum S4 tape drive” on page 6
Chapter 1 HBA Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Array Support
The HBA is supported by the following arrays:
■
■
■
Sun StorageTek 2540
Sun StorageTek 6140
Sun StorageTek 6540
System Support
The HBA is supported by the following systems:
■
■
■
Sun StorageTek 9990
Sun StorageTek 9980/9985
Sun StorageTek 9970
Tape Storage Support
The HBA is supported by the following tape storage:
■
■
■
■
■
■
■
■
■
■
■
■
■
Sun StorageTek SL48 tape library
Sun StorageTek SL24 tape autoloader
Sun StorageTek SL500 modular library
Sun StorageTek SL1400 tape library
Sun StorageTek SL3000 tape library
Sun StorageTek L8500 modular library
Sun StorageTek Virtual Tape Library (VTL): VTL Value and VTL Plus
Sun StorageTek T10000A and T10000B
Sun StorageTek T9840C, and T9840D tape drives
Sun StorageTek T9940B tape drive
IBM and HP LT03 tape drives
IBM and HP LT04 tape drives
Quantum S4 tape drive
Switch Support
The HBA is supported with the following Fibre Channel switches:
■
Brocade DCX backbone switch
6
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Brocade 200E switch
Brocade 300 switch
Brocade SW4100 switch
Brocade SW4900 switch
Brocade SW5000 switch
Brocade SW5100 switch
Brocade SW5300 switch
Brocade SW7500 switch
Cisco MDS9124 24-port multilayer fabric switch
Cisco MDS 9134 multilayer fabric switch
Cisco MDS 9140 multilayer fabric switch
Cisco MDS 9216A multilayer fabric switch
Cisco MDS 9216i multilayer fabric switch
Cisco MDS 9222i multiservice modular switch
Cisco MDS 9509 multilayer director
Cisco MDS 9513 multilayer director
McData Mi10K director
McData 6140 director
QLogic 9000
QLogic 5800
The HBA is supported by all 1-Gb Ethernet switches.
Environmental Requirements
The HBA environmental requirements are listed in TABLE 1-4.
TABLE 1-4
Operating
HBA Environmental Requirements
Specification
Non-Operating
Temperature 0˚ to 55˚C, non-condensing
-40˚C to 70˚C, non-condensing
n/a
Airflow
150 lfm
Humidity
10% to 90% RH, non-condensing, 27˚C max wet
bulb
93% RH, nonconducting, 38˚C max wet bulb
Chapter 1 HBA Overview
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 1-4
Operating
HBA Environmental Requirements
Specification
Altitude
Vibration
Shock
Non-Operating
3200m
12,200m
0.20G in all axes swept for 5-500 Hz sine
5G, 11 ms half-sine
1.0G in all axes 5-500-5 Hz sine
30G, 11 ms half-sine
8
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
2
Hardware Installation and Removal
This chapter describes the tasks required to install and remove the HBA. Refer to
This chapter contains the following topics:
■
■
■
■
■
“Observing ESD and Handling Precautions” on page 9
“Installing the Hardware” on page 10
“Testing the Installation” on page 17
“Replacing the SFP+ Unit on the HBA” on page 24
“Removing the Hardware” on page 24
Observing ESD and Handling
Precautions
Caution – Damage to the HBA can occur as the result of careless handling or
electrostatic discharge (ESD). Always handle the HBA with care to avoid damage to
electrostatic sensitive components.
To minimize the possibility of ESD-related damage, use both a workstation antistatic
mat and an ESD wrist strap. You can get an ESD wrist strap from any reputable
electronics store or from Sun as part number #250-1007. Observe the following
precautions to avoid ESD-related problems:
■
Leave the HBA in its antistatic bag until you are ready to install it in the system.
■
Always use a properly fitted and grounded wrist strap or other suitable ESD
protection when handling the HBA, and observe proper ESD grounding
techniques.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
Hold the HBA by the edge of the PCB, not by the connectors.
Place the HBA on a properly grounded antistatic work surface pad when it is out
of its protective antistatic bag.
in these sections:
■
■
■
■
■
“To Install the HBA” on page 10
“To Connect the Optical Cable” on page 14
“To Apply Power” on page 15
“To Verify Proper Installation (for the Solaris OS)” on page 17
“To Verify Attached Storage (for the Solaris OS)” on page 21
▼ To Install the HBA
The HBA comes with a low-profile PCIe bracket installed. A standard bracket is
included in the box with the HBA. The low-profile mounting bracket is shorter than
the standard bracket; approximately 3.11 in. (7.9 cm) compared to 4.75 in. (12.06 cm).
If you need to change the bracket for HBA installation, you must first remove the
optical transceiver (two transceivers on the two-port adapter) from its housing. This
transceiver and change the bracket safely.
The HBA uses different types of transceivers. This procedure shows an example of
one type.
1. Attach an antistatic strap (refer to “Observing ESD and Handling Precautions”
on page 9).
2. Refer to your system installation or service manual to determine an appropriate
PCI-Express slot in which to install the HBA.
3. Shut down, power off, and unplug the system.
4. Remove the system case.
5. Remove the blank panel from an empty PCI-Express slot.
6. (Optional) Perform the following steps to replace the PCI bracket.
10
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
a. Remove the transceiver from its cage assembly (see FIGURE 2-2) by pulling the
bail (handle) out and down to release the latch and gently pull the
transceiver out of its housing.
Do not force it. After the latch is released, the transceiver slides out easily..
Caution – This is a delicate operation–take care not to damage the transceiver.
FIGURE 2-1 Optical Transceiver
FIGURE 2-2 A Partly Extracted Optical Transceiver and an Optical Transciever That is Latched In Place
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
11
b. Observing ESD precautions, store the transceiver in an ESD-safe place.
c. Remove the mounting bracket screws from the top of the HBA.
FIGURE 2-3 Removing the Bracket Mounting Screws
d. Remove the bracket and store it for future use.
e. Align the new mounting bracket tabs with the holes in the HBA.
Caution – Be careful not to push the bracket past the transceiver housing's
grounding tabs.
Make sure the LEDs are properly aligned with the holes in the bracket.
f. Re-install the screws that attach the HBA to the bracket.
g. Re-install the transceiver by sliding it into the housing.
When the latch engages, it clicks.
h. Push the bail back into place.
7. Insert the HBA into the empty PCI-Express 8-lane slot and press firmly until
the adapter is seated.
8. Secure the mounting bracket of the HBA to the case with the panel screw or
clip.
12
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Replace the computer case and tighten the case screws.
The HBA is now installed in the computer and is ready for media attachment.
▼ To Connect the Optical Cable
Note – The HBA does not allow normal data transmission on an optical link unless
it is connected to another similar or compatible Fibre Channel product (that is,
multimode to multimode).
Use multimode fiber-optic cable, intended for short-wave lasers, that adheres to the
specifications in TABLE 2-1.
TABLE 2-1
Optical Cable Specifications
Fiber-Optic Cable
Maximum Length
Minimum Length Connector
OM3 - Multimode 50/125 micron
fiber (2000 MHz*km bandwidth
cable)
2.125 Gb/s: 0.5m - 500m .5 meters
4.25 Gb/s: 0.5m - 380m
LC
LC
LC
8.5 Gb/s 0.5m – 150m
OM2 - Multimode 50/125 micron
fiber (500 MHz*km bandwidth cable)
2.125 Gb/s: 0.5m – 300m .5 meters
4.25 Gb/s: 0.5m – 150m
8.5 Gb/s 0.5m – 50m
OM1 - Multimode 62.5/125 micron
fiber (200 MHz*km bandwidth cable)
2.125 Gb/s: 0.5m – 150m .5 meters
4.25 Gb/s: 0.5m – 70m
8.5 Gb/s 0.5m – 21m
1. Connect the fiber-optic cable to an LC connector on the HBA (see FIGURE 2-4).
Chapter 2 Hardware Installation and Removal
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 2-4 Attaching the Optical Cable
2. Connect the other end of the cable to the FC device.
After the optical cable is connected to the HBA, you can power on the system.
▼ To Apply Power
1. Verify that the HBA is securely installed in the system.
2. Verify that the correct fiber-optic cable is attached.
3. Refer to your system installation or service manual to determine how to power
on the system.
▼ (LED) Status
Yellow and green LEDs can be seen through openings in the mounting bracket of
the HBA. Each port has a corresponding set of yellow and green LEDs (see
FIGURE 2-5).
14
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 2-5 LEDs
Figure Legend
1
2
Port 0 LEDs
Port 1 LEDs
4. Observe the light-emitting diode (LED) status for the power-on self test (POST)
results as shown in TABLE 2-2.
TABLE 2-2
LED Status
Green LED
Off
Yellow LED
State
Off
Wake-Up Failure (Dead Board)
POST failure (Dead Board)
Wake-Up Failure Monitor
Failure in POST
Off
On
Off
Slow Blink
Fast Blink
Flashing
Off
Off
Off
POST Processing in Progress
Failure While Functioning
Failure While Functioning
2 Gb Link Rate – Normal, Link up
4 Gb Link Rate – Normal, Link up
8 Gb Link Rate – Normal, Link up
On
On
On
On
2 Fast Blinks
3 Fast Blinks
4 Fast Blinks
On
On
Chapter 2 Hardware Installation and Removal
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 2-2
LED Status (Continued)
Green LED
Slow Blink
Slow Blink
Slow Blink
Slow Blink
Slow Blink
Fast blink
Fast blink
Yellow LED
Off
State
Normal – Link Down or not started
Not Defined
On
Slow Blink
Fast Blink
Flashing
Off
Off-line for Download
Restricted Off-line Mode (Waiting for Restart)
Restricted Off-line Mode, Test Active
Debug Monitor in Restricted Mode
Not Defined
On
Testing the Installation
This section contains the following topics:
■
“To Verify Proper Installation (for the Solaris OS)” on page 17
“To Verify Attached Storage (for the Solaris OS)” on page 21
■
▼ To Verify Proper Installation (for the Solaris OS)
1. Use the show-devscommand at the okprompt to list the installed devices.
The HBA can be identified in the output by looking for the SUNW,emlxs@n and
SUNW,emlxs@n,1node names, where n is usually a single-digit number from 0
to 9. In this example, there are two dual port (SG-XPCIE2FC-EM8-Z) and one
single port (SG-XPCIE1FC-EM8-Z) HBAs installed.
{0} ok show-devs
/pci@7c0/pci@0
/pci@7c0/pci@0/pci@9
/pci@7c0/pci@0/pci@8
/pci@7c0/pci@0/pci@2
/pci@7c0/pci@0/pci@2
/pci@7c0/pci@0/pci@1
/pci@7c0/pci@0/pci@9/SUNW,emlxs@0,1
/pci@7c0/pci@0/pci@9/SUNW,emlxs@0
/pci@7c0/pci@0/pci@9/SUNW,emlxs@0,1/fp@0,0
16
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
(continued)
/pci@7c0/pci@0/pci@9/SUNW,emlxs@0,1/fp@0,0/disk
/pci@7c0/pci@0/pci@9/SUNW,emlxs@0/fp@0,0
/pci@7c0/pci@0/pci@9/SUNW,emlxs@0/fp@0,0/disk
/pci@7c0/pci@0/pci@8/SUNW,emlxs@0
/pci@7c0/pci@0/pci@8/SUNW,emlxs@0/fp@0,0
/pci@7c0/pci@0/pci@8/SUNW,emlxs@0/fp@0,0/tape/pci@7c0/pci@0/pci@8
/SUNW,emlxs@0/fp@0,0/disk
/pci@7c0/pci@0/pci@2/network@0,1
/pci@7c0/pci@0/pci@2/network@0
/pci@7c0/pci@0/pci@1/pci@0,2
/pci@7c0/pci@0/pci@1/pci@0
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@2,1
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@2
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1,1
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@2,1/fp@0,0
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@2,1/fp@0,0/disk
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@2/fp@0,0
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@2/fp@0,0/disk
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1,1/fp@0,0
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1,1/fp@0,0/tape
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1,1/fp@0,0/disk
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1/fp@0,0
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1/fp@0,0/tape
/pci@7c0/pci@0/pci@1/pci@0,2/SUNW,emlxs@1/fp@0,0/disk
/pci@7c0/pci@0/pci@1/pci@0/ide@8
/pci@7c0/pci@0/pci@1/pci@0/usb@6
/pci@7c0/pci@0/pci@1/pci@0/usb@5
/pci@7c0/pci@0/pci@1/pci@0/isa@2
/pci@7c0/pci@0/pci@1/pci@0/ide@8/cdrom
/pci@7c0/pci@0/pci@1/pci@0/ide@8/disk
/pci@7c0/pci@0/pci@1/pci@0/usb@6/hub@1
/pci@7c0/pci@0/pci@1/pci@0/isa@2/serial@0,3f8
/pci@780/pci@0
/pci@780/pci@0/pci@9
/pci@780/pci@0/pci@8
/pci@780/pci@0/pci@2
/pci@780/pci@0/pci@1
/pci@780/pci@0/pci@9/scsi@0
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
17
(continued)
/pci@780/pci@0/pci@9/scsi@0/disk
/pci@780/pci@0/pci@9/scsi@0/tape
/pci@780/pci@0/pci@8/SUNW,emlxs@0,1
/pci@780/pci@0/pci@8/SUNW,emlxs@0
/pci@780/pci@0/pci@8/SUNW,emlxs@0,1/fp@0,0
/pci@780/pci@0/pci@8/SUNW,emlxs@0,1/fp@0,0/tape
/pci@780/pci@0/pci@8/SUNW,emlxs@0,1/fp@0,0/disk
/pci@780/pci@0/pci@8/SUNW,emlxs@0/fp@0,0
/pci@780/pci@0/pci@8/SUNW,emlxs@0/fp@0,0/tape
/pci@780/pci@0/pci@8/SUNW,emlxs@0/fp@0,0/disk
/pci@780/pci@0/pci@1/network@0,1
/pci@780/pci@0/pci@1/network@0
/packages/SUNW,builtin-drivers
{c} ok
2. To positively identify the port as a Sun StorageTek 8 Gb FC port, use the cd
command to change to the SUNW,emlxs@n directories, and use the
.propertiescommand.
18
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
In this example, the .propertiescommand output displays the properties of
the two ports in a dual port HBA.
ok cd /pci@780/pci@0/pci@8/SUNW,emlxs@0
{c} ok .properties
assigned-addresses
00002000
82060010 00000000 00300000 00000000
82060018 00000000 00304000 00000000 00004000
81060020 00000000 00000000 00000000 00000100
82060030 00000000 00340000 00000000 00040000
port_wwn
node_wwn
alternate-reg
reg
10 00 00 00 c9 71 be fc
20 00 00 00 c9 71 be fc
01060020 00000000 00000000 00000000 00000100
00060000 00000000 00000000 00000000 00000000
03060010 00000000 00000000 00000000 00001000
03060018 00000000 00000000 00000000 00000100
02060030 00000000 00000000 00000000 00020000
compatible
pciex10df,fc40.10df.fc42.3
pciex10df,fc40.10df.fc42
pciex10df,fc42
pciex10df,fc40.3
pciex10df,fc40
pciexclass,0c0400
pciexclass,0c04
02625a00
00000000
00000002
Copyright (c) 2000-2007 Emulex
LPe12002-S
clock-frequency
#size-cells
#address-cells
copyright
model
name
SUNW,emlxs
device_type
manufacturer
fcode-version
fcode-rom-offset
interrupts
class-code
subsystem-id
subsystem-vendor-id
revision-id
device-id
scsi-fcp
Emulex
3.01a1
0000c400
00000001
000c0400
0000fc42
000010df
00000003
0000fc40
vendor-id
000010df
{c} ok
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
19
assigned-addresses
00002000
82080110 00000000 03504000 00000000
82080118 00000000 03506000 00000000 00002000
81080120 00000000 00003100 00000000 00000100
82080130 00000000 03580000 00000000 00040000
port_wwn
node_wwn
alternate-reg
reg
10 00 00 00 c9 4b 3b 39
20 00 00 00 c9 4b 3b 39
01080120 00000000 00000000 00000000 00000100
00080100 00000000 00000000 00000000 00000000
03080110 00000000 00000000 00000000 00001000
03080118 00000000 00000000 00000000 00000100
02080130 00000000 00000000 00000000 00020000
compatible
pci10df,fc20
02625a00
00000000
clock-frequency
#size-cells
#address-cells
copyright
model
name
device_type
manufacturer
fcode-version
fcode-rom-offset
devsel-speed
class-code
00000002
Copyright (c) 2008 Emulex
LPe12002-S
SUNW,emlxs
scsi-fcp
Emulex
1.50a8
0000c000
00000000
000c0400
interrupts
00000002
latency-timer
cache-line-size
max-latency
min-grant
00000000
00000010
00000000
00000000
subsystem-id
subsystem-vendor-id
revision-id
device-id
0000fc22
000010df
00000002
0000fc20
vendor-id
000010df
{0} ok
▼ To Verify Attached Storage (for the Solaris OS)
●
If online storage is connected to the HBA, use the apply show-children
command to list the attached storage.
20
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Note – You might need to use the reset-allcommand before using the apply
show-childrencommand.
In the example that follows, four SANS with 14 to 16 drives each and an FC tape
drive are attached to the two ports or a dual-port HBA.
{14} ok show-children
Device PortID 10600 WWPN 200600a0b8220346
LUN 0
LUN 1
LUN 2
LUN 3
LUN 4
LUN 5
LUN 6
LUN 7
LUN 8
LUN 9
LUN a
LUN b
LUN c
LUN d
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
Device PortID 10700 WWPN 50020f2300006cee
LUN 0
LUN 1
LUN 2
LUN 3
LUN 4
LUN 5
LUN 6
LUN 7
LUN 8
LUN 9
LUN a
LUN b
LUN c
LUN d
LUN e
LUN f
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
21
(continued)
Device PortID 20600 WWPN 200600a0b8220345
LUN 0
LUN 1
LUN 2
LUN 3
LUN 4
LUN 5
LUN 6
LUN 7
LUN 8
LUN 9
LUN a
LUN b
LUN c
LUN d
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
CSM100_R_FC
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
0612
Device PortID 20700 WWPN 50020f2300003206
LUN 0
LUN 1
LUN 2
LUN 3
LUN 4
LUN 5
LUN 6
LUN 7
LUN 8
LUN 9
LUN a
LUN b
LUN c
LUN d
LUN e
LUN f
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
Disk
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
SUN
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
T300
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
0301
Device PortID 20900 WWPN 500104f00047457b
LUN 0 Removable Tape STK T9840B
{14} ok
1.34
22
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the SFP+ Unit on the HBA
The Small Form Factor Pluggable (SFP+) optics unit on this card is considered a part
of the card, NOT as a separate field replaceable unit (FRU). Therefore, in the event
that the SFP+ unit malfunctions, you must return the entire card in order to receive
a replacement SFP+ unit. Always return any malfunctioning card with the SFP+ unit
attached. For information about removing the card from a system in order to return
it, see “To Remove the HBA Hardware” on page 24.
Removing the Hardware
The following procedures describe how to remove the HBA. Refer to your system
installation or service manual for detailed HBA adapter removal instructions.
The hardware removal process involves these general steps:
1. Halting the operating system and removing power from the server blade, or
computer.
2. Removing the HBA hardware.
▼ To Remove the HBA Hardware
1. Use an ESD strap (refer to “Observing ESD and Handling Precautions” on
page 9).
2. Refer to your system documentation to shut down, power off, and unplug the
system.
3. Disconnect all cables.
4. Unscrew the case screws and remove the system case.
5. Remove the mounting bracket of the HBA from the system by unscrewing the
panel screw or removing the clip, whichever is being used.
You can now remove the HBA.
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
23
24
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
3
HBA Software Installation
follow the instructions in this chapter for your operating system to install the HBA
driver and any other utilities that are required.
■
■
■
“Driver Software for the Solaris OS” on page 25
“Installing Software For the Red Hat and SUSE Linux OSes” on page 26
“Installing Software For the Windows Server 2003 or Windows Server 2008 OS”
on page 27
■
“Configuration and Diagnostic Utilities” on page 28
Driver Software for the Solaris OS
The HBA driver for the Solaris OS is included with the Solaris 10 1/06 (s10u1) OS
release. No additional patches or packages are required to support the HBA on
minimum supported versions of the Solaris 10 OS for x64/x86 systems.
Solaris Diagnostic Support
Diagnostic support for the HBA is included in the SunVTS™ software beginning
with version 6.3. The SunVTS software is included with the Solaris 10 11/06 (s10u3)
OS release, and is also available for download at:
The emlxtestutility, which is included in the SunVTS software, supports the
following functions:
25
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
■
■
Connectivity verification
Firmware version and checksum test
Self-test
Loopback tests
■
■
■
■
External
Internal, single-bit
Internal, 10-bit
Mailbox
Installing Software For the Red Hat and
SUSE Linux OSes
No updates are required to support the HBA on minimum supported versions of
Linux.
For diagnostic support, you might need to rebuild the Linux driver. Before
rebuilding the drivers for Linux, you must have the required Linux OS installed on
the hard disk. The driver and utilities are available for download at the Emulex
support site for Sun Microsystems.
▼ To Install the HBA Software For the Linux OS
1. Go to the Emulex support site for Sun Microsystems at:
2. Locate the Sun StorageTek section, and click the model number (SG-XPCIE1FC-
EM8-Z) for the HBA you want to install.
3. Locate the Linux Driver section, and click Download to copy the driver files to
a local file system.
4. Click Download to copy the management utilities to a local file system.
5. Click Manual to copy the PDF manual, and then follow the installation and
configuration procedures.
6. Click PDF Manual to download installation, configuration, and troubleshooting
information.
26
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Install the driver for Linux as described in the Emulex Driver and Utilities for
Linux User Manual.
8. Install the management utilities as described in the Emulex driver and utilities
documentation.
▼ To Install the HBA Software For the VMware
Technology
You must obtain the drivers from VMware.
1. Go to the Emulex support site for Sun Microsystems at:
2. Locate the VMware section, and click the model number (SG-XPCIE1FC-EM8-
Z) for the HBA you want to install.
3. Click Download to copy the management utilities to a local file system.
4. Click Manual to copy the PDF manual, and then follow the installation and
configuration procedures.
5. Click PDF Manual to download installation, configuration, and troubleshooting
information.
6. Obtain the driver from VMware and install the driver as described in the
VMware documentation.
7. Install the management utilities as described in the Emulex driver and utilities
documentation.
Installing Software For the Windows
Server 2003 or Windows Server 2008 OS
The HBA driver and applications kits for the Windows Server 2003 or Windows
Server 2008 OS is available for download at the Emulex support site for Sun
Microsystems.
Chapter 3 HBA Software Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
27
▼ To Install the Software For the Windows Server
2003 or Windows Server 2008 OS
1. Go to the Emulex support site for Sun Microsystems at:
2. Locate the driver section for Windows.
3. Download the Driver Kit by clicking Download.
4. Click PDF Manual to download the installation guide for the Windows OS.
5. Install the driver and management utilities for the Windows OS as described in
the installation guide.
Configuration and Diagnostic Utilities
Use the HBAnywhereutility or the lputilcommand-line interface (CLI) utility to
configure the HBA. These utilities are available for Linux and Windows OSes and
provide support for the following functions:
■
■
■
■
■
■
■
■
Discover local and remote hosts, HBAs, targets, and LUNs
Reset HBAs
Set HBA driver parameters
Update firmware
Enable or disable the system BIOS
Run diagnostic tests on HBAs
Manage out-of-band HBAs
Manage local and in-band remote HBAs
For more information about the HBAnywareand lputilutilities, download their
user manuals from the Emulex support site for Sun Microsystems.
28
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
4
Known Issues
This chapter contains any known issues with the HBA.
Reboot Fails on the SPARC Enterprise
M8000 System (6728135)
On the SPARC Enterprise M8000 system, if you use the stmsboot command to
provide dual paths to the boot device, on occasion the boot device is not found and
the reboot does not succeed.
At the console, the following message will be printed:
Can't open boot device
Workaround: When this occurs, retry the boot operation. The system will now
reboot as expected.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Sun StorageTek 8 Gb FC PCI-Express HBA, Emulex Installation Guide • December 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|