Owner’s Manual
for
™
Manual Reel Mower
(Model MM-2)
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM-2
WELCOME
Congratulations on your purchase of a Sunlawn mower. This and our
other Sunlawn products originate from our commitment to
conscientious gardening solutions. Please use this manual as a
reference.
WARRANTY
Sunlawn, Inc. (the Manufacturer) guarantees this product for private
use for a period of 2 years from the date of purchase. This guarantee
applies to all serious defects of the product which can be proven to
have been caused by faulty materials or workmanship. The
Manufacturer has the option of supplying a replacement of the product
in perfect working order or repairing the product free of charge at an
authorized facility, provided that the following conditions are fulfilled:
• The appliance has been handled correctly and in accordance with
the instructions in the Owner’s Manual.
• Neither the buyer nor a third party has attempted to repair the
product.
This guarantee is void if replacement parts or accessories are used
other than those approved by the Manufacturer.
The product, accompanied by a copy of the original receipt, must be
delivered, prepaid, to a service center authorized by the Manufacturer.
This Manufacturer’s guarantee shall not affect any guarantee claims
against the dealer or seller of the product.
USE OF THIS PRODUCT
This mower is designed for use on residential lawns. It is not designed
for commercial use or for use in public facilities, parks, sporting
grounds, roads, or in agriculture or forestry areas.
This mower is for cutting lawns only. It must not be used to trim
hedges, bushes or shrubs, for cutting or pruning, or for any mowing
where both wheels and the roller are not fully supporting the mower.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM--2
ASSEMBLY
PARTS LIST
1. Handle top section
2. Handle grip
16. Roller screw (2)
17. Cutting bar
18. Cutting bar secure bolt (2)
19. Cutting bar adjusting
bolt (2)
20. Cutting bar spring (2)
21. Wheel (2)
22. Wheel spacer (2)
23. Wheel clip (2)
24. Hub cap (2)
25. Pinion gear (L/R)
26. Manual drive pawl
27. Spacer (2)
3. Handle mid section
4. Handle lower section
5. Handle bolt (4) [A]
6. Handle wing nut (4) [A]
7. Handle spacer [B]
8. Handle cotter pin [B]
9. Adjustment knob [B]
10. Side panels (L/R)
11. Adjusting arms (L /R)
12. Compression nut (2)
13. Reel blade
14. Catcher apron
15. Roller assembly
28. Feature cover
29. Top cover
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM-2
ASSEMBLE THE HANDLE SECTIONS
1. Set the cutting height to the highest setting as shown below. This
will make it easier to attach the lower handle section.
a. Loosen the two large black knobs [Part # 9], one on each side
of the mower body, to allow movement of the height
adjustment arms [Part # 11]. NOTE: the handle is mounted to
the adjusting arms and thus moves with the arms.
b. Set the height to the highest setting and re-tighten the black
knobs.
2. Fit the lower section of the handle [Part # 4] so that the holes are
over the handle posts on the mower. [See Insert B] Then rock the
handle to align the locking tabs and allow the handle section to fit into
place. Place the spacer [Part # 7] over the post and put the cotter pin
(Part # 8] through the hole to secure the handle.
3. Continue assembly of the middle [Part # 3] and top sections [Part
# 1] of the handle using the handle bolts and wing nuts [Part # 5 and
6].
ADJUSTING THE CUTTING HEIGHT
The cutting height of the MM-2 may be adjusted from approximately
1.0 inch up to approximately 2.9 inches. Actual height may vary
according to the height of the turf. Adjust the mower to the desired
height as follows:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM--2
1. Loosen the two large black knobs [Part # 9], one on each side of
the mower body, to allow movement of the height adjustment arms
[Part # 11]. (This is the same movement used to attach the
handle.) NOTE: the handle is mounted to the height adjustment
arms and thus moves with the arms.
2. Set the height, using the scale on the back of the adjusting arms to
the same setting on both sides and re-tighten the black knobs. The
mower is now ready to mow at the desired height setting.
OPERATION
INSPECT THE MOWING AREA
1. Before beginning to mow, remove any foreign objects, such as
stones, branches, or toys, from the area.
2. Continue to check for such obstacles during mowing.
The Lawn Should Be Relatively Dry
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM-2
1. Mowing wet grass causes an uneven cut and can cause damage to
the electrical components of the mower.
2. Do not mow when it is raining.
!
WARNING
• Before starting the mower, check within the blade area for any
foreign objects and remove them.
•
Do not operate the mower on areas other than turf surfaces.
The mower should be sitting upright on a level part of the lawn
before starting operation
NORMAL MOWING
To obtain a clean cut, push the mower in straight lines (passes) at a
deliberate walking pace. Overlap the passes to even the cut and to
avoid any uncut strips.
MOWING USING THE GRASS CATCHER (OPTIONAL ACCESSORY)
The grass catcher collects the clippings as it mows.
1. Install the catcher apron [Part # 14] on the non-spring pin side
2. Push the spring pin on the other side
3. Install the apron on the spring pin side
The grass catcher attaches at the grass catcher hooks on the mower
and by the strap to the mower handle, as seen below.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM--2
Mow using the same procedure as for normal mowing (described
above).
MOWING: GENERAL INFORMATION
THE 1/3 RULE
This is the key to enjoyable mowing and a healthy lawn.
1. The lawn should be mowed regularly, at least once a week during
the growing season.
2. Be guided by observing the lawn and taking care not to remove
more than 1/3 of the total height of the turf at any mowing.
3. Following this rule will stimulate the turf’s root growth, maintain its
health, and encourage its natural ability to crowd out unwanted
weeds.
If the lawn has become too high (over 4 inches in height) then it is
best to set the mower to the highest setting to mow. After mowing,
reset down to the normal level and mow again within a day or two.
Removing too much of the turf’s height, especially in the heat of
summer, can cause root shock and weaken the lawn; bringing down
the height by successive mowings over two or more days can avoid
this damage and maintain the health of the turf.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM-2
If the lawn is overgrown (to higher than 4 inches) it may be advisable
to use a brush cutter to remove the excess turf mass before resuming
mowing at normal heights.
MAINTENANCE
CLEANING
After using the mower, clean with a moist cloth. Spray the cylinder
and cutting bar with silicon spray lube.
GENERAL MAINTENANCE
Regularly check to insure that all bolts, nuts, and screws are tight and
that the mower is in good working order. Worn out and damaged parts
should be replaced.
The blades, if properly cared for, will mow for years before requiring
sharpening. Sharpening can only be done by a professional using
a cylinder grinder and proper techniques.
STORAGE
1. Store the MM-2 in a cool, dry place.
2. The mower should be stored out of the reach of children.
READJUSTING THE BLADE CLEARANCE
The blades are optimally adjusted from the factory. However, after
using the mower for a long period, if the cut is not clean, the blades
need readjusting. The procedure is as follows:
1. Turn the mower over to expose the cutting bar on the bottom of the
mower. [Part # 17].
Using a 10mm open end wrench, tighten the hex bolt approximately
1/4 turn [Part # 19] at one end of the cutting bar until the cutting bar
and cylinder come into contact. Spin the blade cylinder by hand and
back off the bolt approximately 1/8 turn or until the cutting bar and
cylinder are no longer in contact.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Manual — Sunlawn MM--2
2. Make the same adjustment at the other end of the cutting bar.
3. Now check the adjustment using the small 0.05mm/0.002 inch
gauge (silver strip) supplied with the MM-2 (or any 0.05mm/0.002
inch feeler gauge). If the gauge is held by the cylinder blades but
the cylinder and cutting bar are not touching then the adjustment is
correct.
4. The blades may also be tested by inserting a piece of paper
vertically into the blades while turning them by hand.
!
WARNING
Blades are sharp! Be careful of injury —
handle the blades carefully to avoid
cutting yourself. Wear appropriate gloves
or hand protection.
TECHNICAL DATA
Mower
8
Cutting width:
Cutting height rough (from floor): 1.0 to 2.9 inches
40 cm (16 inches)
Download from Www.Somanuals.com. All Manuals Search And Download.
|