PARTS AND OPERATION MANUAL
STOW
A DIVISION OF MULTIQUIP INC.
PLASTER/MORTAR
MIXERS
MS-40H
(Steel-Drum Hydraulic)
Revision #1 (05/17/02)
STOW CONSTRUCTION EQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
DIVISION OF MULTIQUIP INC.
PARTS DEPARTMENT:
800-427-1244
FAX: 800-672-7877
A
CARSON, CALIFORNIA 90749
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
310-537-3700 • 888-252-STOW [888-252-7869]
FAX:310-537-1986 • FAX:800-556-1986
800-478-1244
FAX:310-631-5032
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help ........................................... 3
Table Of Contents .................................................... 4
Parts Ordering Procedures ...................................... 5
Operation and Safety Decals ................................... 6
Rules For Safe Operation .....................................7-8
Specifications ........................................................... 9
General Information ............................................... 10
Engine
Honda Engine Assembly...................................40-41
5 HP Motor
Single Phase Electric Motor Assembly .............42-43
Three Phase Electric Motor Assembly..............44-45
Terms and Conditions Of Sale — Parts ................. 46
MQ STOW — Mortar Mixer
Controls.................................................................. 11
Electric Motor ......................................................... 12
Towing .................................................................... 13
Paddle Blade Adjustment ....................................... 15
Initial Start-Up ...................................................16-17
Maintenance .......................................................... 18
Troubleshooting (Engine)....................................... 19
Troubleshooting (Engine/Mixer) ............................. 20
Explanation Of Codes In Remarks Column ........... 22
Suggested Spare Parts .......................................... 23
Nameplate and Decals......................................24-25
Engine End Paddle Assembly ...........................26-27
Tow End Paddle Assembly ................................28-29
Steel Mixing Drum Assembly ............................30-31
Paddle Shaft Assembly .....................................32-33
Hydraulic Assembly...........................................34-35
Frame 3 Assembly ............................................36-37
Engine Cover Assembly ....................................38-39
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
UPS Ground
•
UPS Second Day or Third Day*
•
UPS Next Day*
•
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
Airborne Express*
•
Truck or parcel post
•
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
Additional Discount
1-9 items
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
Now! Direct TOLL-FREE access
to our Parts Department!
UPS Ground Service at no charge for freight
PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
Toll-free nationwide:
800-421-1244
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
Toll-free FAX:
*DISCOUNTS ARE SUBJECT TO CHANGE*
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — OPERATION AND SAFETY DECALS
Machine Safety Decals
This STOW mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenance
information.The illustration below shows these decals as they appear on the mixer.Should any of these decals become unreadable,
replacements can be obtained from your dealer.
SAFETY INSTRUCTIONS
A DIVISION OF MULTIQUIP INC.
1. Read owners manuals before operating.
2. Keep unauthorized and untrained people away from machine during operation.
3. Make sure all safety devices are in place before this machine is started.
4. Make sure engine is turned off and spark plug wire is disconnected before cleaning the
machine.
5. Keep hands and fingers away from moving objects.
6. Do not operate machine in an enclosed area. Proper ventilation is required.
7. Never leave machine unattended when operating.
8. Always stop engine and allow engine to cool before adding fuel or oil.
STOW CONCRETE PRODUCTS — A MULTIQUIP COMPANY — CARSON, CALIFORNIA
P/N 924801
PAGE 6 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — RULES FOR SAFE OPERATION
I
NEVER touch the hot exhaust manifold, muffler or cylinder. Allow
these parts to cool before
servicing engine or mixer.
CAUTION:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the MS-40H mixer:
I
I
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
I
DO NOT operate or service this equipment
before reading this entire manual.
The engine section of this mixer (gasoline only) requires an
adequate free flow of cooling air. Never operate the mixer in
any enclosed or narrow area
I
I
This equipment should not be operated by persons under 18
years of age.
where free flow of the air is
restricted. If the air flow is restricted
it will cause serious damage to the
mixer or engine and may cause
injury to people. Remember the
mixer's engine gives off DEADLY
carbon monoxide gas.
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job.
I
I
NEVER operate this equipment when not
feelingwellduetofatigue, illnessor taking
medicine.
I
Always refuel in a well-ventilated area, away from sparks and
open flames.
I
Always use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
NEVER operate this equipment under the
influence or drugs or alcohol.
I
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
I
NEVER operate the mixer in an explosive atmosphere or near
combustible materials. An explosion or fire could result
causing severe bodily harm or even death.
I
I
I
Manufacture does not assume responsibility for any accident
due to equipment modifications.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Always check the machine for loosened threads or bolts before
starting.
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — RULES FOR SAFE OPERATION
I
I
I
Caution must be exercised while servicing this equipment.
Rotating and moving parts can cause injury if contacted.
CAUTION:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
When towing, an adequate safety chain must be fastened to
the frame, refer to page 13.
Keep all inexperienced and unauthorized people away from
the equipment at all times.
I
I
Unauthorized equipment modifications will void all warranties.
The following safety guidelines should always be used when
operating the MS-40HSHD hydraulic mixers:
Check all fasteners periodically for tightness. Also check
towing tongue bolt, lock nut and wheel lug nuts for wear.
GENERAL SAFETY
I
Stop the engine and disconnect the spark plug before allowing
anybody’s hands in the mixing drum.
I
I
I
Stop the engine when leaving the mixer unattended.
Block the unit when leaving or when using on a slope.
I
I
Never pour or spray water over the engine or electric motor.
Maintain this equipment in a safe operating condition at all
times.
Always stand clear of dump handle when mixer is in operation.
Any binding of material between the mixer blades and drum
will cause drum and handle to quickly move in the discharge
position.
I
I
Always stop the engine before servicing, adding fuel and oil.
NEVER Run engine without air filter. Severe engine may
occur.
I
Depending on type of mixer, test the ON/OFF switch for either
the gasoline engine or electric motor before operating. The
purpose of these switches is to shut down the engine or motor
of the mixer.
I
I
I
Always service air cleaner frequently to prevent carburetor
malfunction.
Always be sure the operator is familiar with proper safety
precautions and operations techniques before using mixer.
Emergencies
Always store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
I
Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department. This information will be
invaluable in the case of an emergency.
I
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
Maintenance Safety
I
NEVER lubricate components or attempt service on a running
machine.
I
I
I
I
NEVER Run engine without air cleaner. Severe engine
damage may occur.
I
Always allow the machine a proper amount of time to cool
before servicing.
Always read, understand, and follow procedures in Operator’s
Manual before attempting to operate equipment.
I
I
Keep the machinery in proper running condition.
Always be sure the operator is familiar with proper safety
precautions and operations techniques before using pump.
Fix damage to the machine immediately and always replace
broken parts.
Always store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
I
I
I
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste. Emergencies
CAUTION:
I
DO NOT operate this equipment unless all
Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department. This information will be
invaluable in the case of an emergency.
guards and safety devices are attached and in
place.
PAGE 8 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — SPECIFICATIONS
Table 1. MS-40H Hydraulic Mixer
Capacity - cu. ft (liters)
12 (340)
3.5 to 4
Bag capacity - bags
Weight - lbs (kg.)
1,010 (458)
Length w/Tow Bar x W x H - in. (cm.)
Height W/Dump Handle - in (cm.)
Discharge Height - in (cm.)
Drive
82 x 51 x 60 (208 x 130 x 152)
75 (191)
23 (58)
Hydraulic
Dump Action
Manual/Hydraulic
5 HP Single-Phase 230/460 Electric
5 HP Three-Phase 230/460 Electric
13 HP Honda
Power Sources
NOTE
In accordance with our established policy of constant
improvement, we reserve the right to amend these
specifications at any time without notice.
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — GENERAL INFORMATION
GENERAL
GASOLINE ENGINE CARE
The STOW MS-40H plaster and mortar hydraulic mixer is
shipped completely assembled and has been factory tested.
For care and operation of the gasoline engine, refer to the
engine manufacturer’s operating instructions furnished with the
engine. We recommend draining and refilling the engine
crankcase at least every thirty hours of operation. Check the
engine oil level daily.
The drum batch capacity of these mixers is between 3.5 and
4.0 bags. With proper care, they will give continuous service
year-after-year.
GASOLINE MIXER OFF/ON SWITCH
This mixer can be powered by either gasoline or electric motors.
The power from the engine rotates a hydraulic pump which
provides hydraulic fluid to a directional control valve. The
control valve directs fluid to the hydraulic motor which causes
the paddle shaft to rotate. This type of hydraulic pump design
provides high mixing torque and eliminatesV-belts, pulleys ect.
This feature is on gasoline engine mixers only.Located on the
side of the engine cover. The purpose of this switch is to start
and stop the mixer in normal operation.
ELECTRIC MOTOR MIXER OFF/ON SWITCH
This feature is on electric motor mixers only.This switch is located
next to the motor. Lift the engine cover to gain access to this
switch.The purpose of this switch is to start and stop the mixer
in normal operation. Never use the electric motor in an explosive
environment.
BEFORE STARTING
Before starting the engine, read the engine owners manual and
thoroughly understand the safety information.
Check the items listed below:
ENGINE THROTTLE AND CHOKE CONTROLS
OIL LEVELS
Please refer to the engine owners manual for specific
instructions.
Be sure to check the oil levels in the engine and hydraulic
reservoir before starting the unit.
HARDWARE
Check all hardware on the mixer before starting. Periodically
inspect all hardware. Loose hardware can contribute to early
component failure and poor performance. Use the torque chart
below as a general guideline and keep all hardware tight:
HARDWARE DIA
5/16"- 18
TORQUE (LB./FT.)
24
37
39
90
3/8" - 24
1/2" - 13
1/2" - 13 (Grade 8)
PAGE 10 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — CONTROLS
Figure 1. Mixer
Mixing Drum — Made of steel. Mixing materials such as
concrete, mortar, plaster are to be placed into this drum for
mixing. Always clean the drum after each use.
Safety Grill — Provided for operator safety.This safety grill is
designed to keep hands and solid objects out of the mixing
drum when in use.This grill should be closed at all times when
mixer is in use. DO NOT remove the grill or grill opening bar.
Keep the grill clean by washing it down daily.
Tow Bar — When towing is required, connect tow bar to a
vehicle. Reference page 13.
Bag Cutter—This feature allows compound mixing bags to be
opened easily, therefore allowing the contents of the bag to fall
directly into the mixing drum.
Engine Cover — Lift this cover to gain access to the engine
compartment.
ON/OFF Switch (gasoline) —This switch is provided on mixers
with gasoline engines only and is located on the side of the
engine cover. When activated it will shut down the engine.
Mixing Paddles — Used in the mixing of material. This unit
uses four different types of paddles to provide a fast uniform
mix.
ON/OFF Switch (electric) —This switch is provided on mixers
with electric motors.To gain access to this switch, lift the engine
cover.When activated it will shut down the electric motor.
Manual Dump Handle — Pull this handle downward to dump
the contents of the drum. Push the handle upward to return the
drum to its vertical position.
Blade Engagement Lever — Push the lever in, toward the
engine to engage. Once lever is engaged paddle shaft will
rotate.To disengage pull the lever backwards.
Hydraulic Dump Lever (Option) — Pull lever OUT toward
the engine to engage. Once lever is engaged tub (drum) will
automatically discharge material. push lever IN to return mix
position.
Zerk Fitting —There is, on each end of the mixing drum a zerk
grease fitting.These fittings lubricate the dumping mechanism.
Lubricate both fittings at least twice a week.
Blade Control Lever — Pull lever OUT to mix material, place
lever in CENTER position (neutral) for no mixing, push lever
IN to reverse blade direction.
Oil Sight Glass — Indicates the level of the hydraulic oil in the
reservoir. Oil should be visible within 3/4 height of sight glass.
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — ELECTRIC MOTOR
ELECTRIC MOTOR
NOTE
It is strongly recommended that all electrical wiring be
done by a licensed electrician. Special attention
should be given to the electric switch as well as the
over-and-under voltage protection devices as per
regulations set forth in the local electrical safety code
handbook.
For lubrication care and operation of the electric motor, refer to
your electric motor instruction booklet furnished with the motor.
Protect the electric motor from dust as much as possible and
keep ventilating openings clean.
CAUTION:
I
DO NOT spray water at any time on the
electric motor.
Table 2. Electric Motor Wiring Information
I
DO NOT operate electric motor in a
explosive environment.
Motor
Horsepower
Rating
230 Volt - Single Phase
NEMA Plug Connector
Mating NEMA
Receptacle Connector
The electric motor for this mixer is available in either a 5 HP
single-phase or 5 HP three-phase configuration.The input voltage
requirement for these motors is either 230VAC or 440VAC only.
5 HP
L6-30P P/N 940547
L6-30R P/N 940548
ELECTRIC MOTOR CONNECTION
A 12 inch electrical cable (Figure 2) with a pigtail at one end is
provided with the electrical motor for hookup to a power source.
Table 1. shows the required NEMA connector for the desired
motor horsepower rating. In addition, Table 2 also shows the
matching NEMA approved connector for the required extension
cord.
Figure 2. Single Phase Electric Motor with 12 inch Pigtail Cable
PAGE 12 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER —TOWING
NOTE
STEP 3
Before towing, check with local and state laws for proper
compliance.
E
CTOR LINK
DRAW BAR
The tow bar and chain must be properly attached to the mixer
and towing vehicle prior to towing. Refer to the following
installation instruction:
REMOVE EXCESS
CHAIN (SLACK)
BOTTOM CONNECTOR LINK
Step 1.
Insert the Draw Bar into the main frame. Secure, utilizing the 3/4"
bolt (grade 5) and nylock nut.Tighten to 100 foot pounds.
NOTE
It is critical that the length of the chain be properly
adjusted, to prevent the Draw Bar and the front mixer
stand from dropping to the ground (contact) in the event
the Draw Bar becomes disconnected from the towing
vehicle.
STEP 1
DRAW BAR
If a new safety chain is required use P/N 13363. For a new
connector link use P/N 01004.
BOLT & NUT
CAUTION:
Step 2.
I
Check the following before towing:
Install the chain through the hole located between the frame
gusset and frame angle. Loop the chain together and place under
the Draw Bar.Secure with connector link.
BALL HITCH COUPLER
1.
Check vehicle hitch, ball, and coupler for signs of wear or
damage. Replace any parts that are worn or damaged
before towing.
2
2.
Use only the 2" ball diameter as indicated on your coupler.
Use of any other ball diameter will create an extremely
dangerous condition which can result in separation of the
coupler and ball or ball failure.
DRAW BAR
3.
4.
Be sure the coupler is secured to the hitch ball and the lock
lever is down tight and locked.
Recheck tightness again after towing about 50 miles.
Check that trailer safety chains are properly connected.
K
Step 3.
Extend the chain along the length of the Draw Bar, remove excess
chain (slack) and secure to bottom connector link. Secure the
chain to the towing vehicle, using the connector link.
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — PADDLE BLADE ADJUSTMENT
Figure 3 illustrates the paddle blade adjustment when using a steel drum. If material builds up on the drum, use a rubber mallet to
dislodge the material without adverse effect to the drum.
Figure 3. Paddle Blade Adjustment, Steel Drum
PAGE 14 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — NOTE PAGE
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — INITIAL START-UP
STARTING THE ENGINE (gasoline only)
This section is intended to assist the operator with the initial
start-up of the STOW MS-40H hydraulic mixer. It is extremely
important that this section be read carefully before attempting to
use the mixer in the field.
The following steps outline the procedure for starting the engine.
Depending on the type of engine employed in the mixer the
steps may vary slightly. If your mixer has an electric motor
disregard this section.
DO NOT use your mixer until this section is thoroughly
understood.
1.
Move the fuel shut-off lever (Figure 5) to the ON position.
CAUTION:
Failure to understand the operation of theMS-
40H hydraulic mixer could result in severe
damage to the mixer or personal injury.
See Figure 1 (page 11) for the location of any control referenced
in this manual.
LUBRICANTS
ENGINE OIL
1.
2.
Remove the engine oil dipstick from its holder.
Figure 5. Fuel Shut-OFF Lever
Determine if the engine oil is low, add correct amount of
engine oil to bring oil level to a normal safe level.
2.
To start a cold engine, move the choke lever (Figure 6) to
the CLOSED position.
HYDRAULIC OIL RESERVOIR
1.
Make sure the hydraulic reservoir is full. Hydraulic oil
should be visible within 3/4 height of the sight glass (Figure
4). If low use grade AWD 46 hydraulic oil or equivalent.
Figure 4. Sight Glass
ZERK GREASE FITTINGS
Figure 6. Choke Lever
1.
Check the zerk grease fittings at each end of the mixing
drum. These grease fittings lubricate the dumping
mechanism. If the dumping handle is stiff or hard to move
lubricate these fittings.
3.
Move the throttle lever (Figure 7) away from the slow
position, about 1/3 of the way toward the fast position.
FUEL
1.
If your mixer has a gasoline engine, determine if the engine
fuel is low. If fuel is low, remove the fuel filler cap and fill
with unleaded gasoline.
CAUTION
Handle fuel safely. Motor fuels are highly flammable and can be dangerous
if mishandled. DO NOT smoke while refueling. Do not attempt to refuel
mixer if the engine is hot or running. Always allow engine to cool before
refueling.
Figure 7. Throttle lever Lever
PAGE 16 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — INITIAL START-UP
MIXING
4.
Turn the engine switch (Figure 8) to the ON position.
1.
2.
3.
The paddle shaft inside the drum should be rotating at this
time.
Lift the mixing bag compound onto the steel grate over the
bag cutter and let the contents fall into the drum.
Add water, and mix compound to desired consistency, then
dump.
NOTE
Be sure to stand clear of the dump handle when the
mixer is operational. Any binding of material between
the mixer blades and the drum will cause the drum
handle to move to the discharge position, thus causing
bodily harm.
Figure 8. Engine ON/OFF Switch
5.
Located on the engine cover is the main start/stop switch
(Figure 9). Pull this switch outward to start the engine.
STARTING THE ELECTRIC MOTOR
1.
After the electric motor has been connected to a power
source by a licensed electrician it can then be ready for
use.
2.
Set the electric motor's ON/OFF switch (Figure 11) to the
ON position.
Figure 11. Main ON/OFF Switch
Figure 9. Main ON/OFF Switch
3.
Engage the control lever and verify that the paddle shaft is
rotating, then follow steps 1, 2 and 3 outlined in the mixing
section above.
6.
Pull the starter grip (Figure 10) lightly until you feel
resistance, then pull briskly. Return the starter grip gently.
Push the clutch lever forward, toward the tow tongue end
of the mixer.When engine starts adjust throttle lever so that
paddle shaft inside mixer rotates between 30 - 40 RPM's.
The number of RPM's will vary depending on engine type
and load.
STOPPINGTHE MIXER (gasoline)
1.
Push the main start/stop switch (Figure 9) inward to stop
the engine.
2. Turn the fuel shut-off valve to the OFF position
3.
4.
Disconnect the spark plug.
Clean drum of all debris and foreign matter.
STOPPINGTHE MIXER (electric)
1.
2.
3.
Place the electric motor's start/stop switch (Figure 10) in
the OFF position.
Disconnect the electric motor's extension cord from its
power source.
Figure 10. Starter Grip
Clean drum of all debris and foreign matter.
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — MAINTENANCE
WHEEL BEARINGS
PADDLE SHAFT BEARINGS
After every 3 months of operation, remove the hub dust cap and
inspect the wheel bearings. Once a year, or when required,
disassemble the wheel hubs remove the old grease and repack
the bearings forcing grease between rollers, cone and cage
with a good grade of high speed wheel bearing grease (never
use grease heavier than 265 A.S.T.M. penetration (“No. 2.”) Fill
the wheel hub with grease to the inside diameter of the outer
races and also fill the hub grease cap.
The paddle shafts in theSTOWMS-40H hydraulic mixers rotate
in sealed ball bearings, which require no additional lubrication
as they are packed and sealed at the factory.
There is, on each end of the mixing drum, an zerk grease fitting.
Oil these fittings two or three times each week as they lubricate
the dumping mechanism of the mixing drum.
CAUTION:
Reassemble the hub and mount the wheel. Then tighten the
adjusting nut, at the same time turn the wheel in both directions,
until there is a slight bind to be sure all the bearing surfaces are
in contact.
I
Failure to lubricate the zerk grease fittings
two or three times a week will cause the
dumping mechanism to stiffen, making the
mixer hard to dump.
Then back-off the adjusting nut 1/6 to 1/4 turn or to the nearest
locking hole or sufficiently to allow the wheel to rotate freely
within limits of .001" to .010" end play.Lock the nut at this position.
Install the cotter pin and dust cap, and tighten all hardware.
BEARING BRACKET
Grease the bearing bracket every month.
CLEANING
SHAFT SEALS
Always disconnect the spark plug wire before cleaning the inside
of the drum.
CAUTION:
IMPORTANT -DRUM HEAD SEAL CARE
Never pour or spray water over the gasoline engine or electric
motor.
Grease seals every 40 hours of operation using
any grade #1 lithium base grease. Apply
grease until visible inside of mixing tub (over
grease). This will purge seal system of
contamination.
For consistent performance, long life and high quality mixing,
thoroughly clean the mixer inside and out at the end of each
day’s operation. To prevent lumps of dried mortar from forming
and contamination of future batches, do not allow a buildup of
materials to form on the blades or anywhere inside the drum.
PAGE 18 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER —TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine Troubleshooting (Table 3)
information shown below and on the proceeding page. If the
problem cannot be remedied, please leave the unit just as it
is and consult our company's business office or service
TABLE 3. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Fuel filter clogged?
Stuck carburetor?
Spark plug is red?
Flush or replace fuel tank.
Replace fuel filter
Check float mechanism.
Poor starting
Spark plug is fouled. Check tranistor ignition unit.
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
Spark plug is blue-white?
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Start/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Oil pressure alarm lamp blinks
upon starting?
Check Automatic shutdown circuit "oil sensor".
Replace cylinder and piston and if necessary axel joint.
Tighten cylinder head connecting bolts.
Engine will not turn over?
Cylinder head connecting bolts
loose?
Cylinder head gasket damaged? Replace cylinder head gasket.
Insufficient power output "no
compression"
Malfunction of valve seat?
Spark plug is loose?
Worn piston rings?
Re-seat valves.
Replace spark plug.
Replace piston rings.
Malfunction in air-cleaner
system, air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Insufficient power output
"compression"
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
Malfunction in fuel system?
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER —TROUBLESHOOTING (ENGINE/MIXER)
TABLE 3. ENGINE TROUBLESHOOTING (CONTINUED))
SYMPTOM
POSSIBLE PROBLEM
Malfunction in cooling fan?
Air in-take filter clogged?
SOLUTION
Check or replace cooling fan.
Insufficient power output
"compression" and overheats
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Burns to much fuel
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Replace lubricating oil with correct viscosity.
Replace rings
Lubricating oil is wrong
viscosity?
Exhaust color is continiously
"WHITE"
Worn rings?
Air cleanner clogged?
Clean or replace air cleaner.
Choke valve has not been set
to the correct position?
Adjust choke valve to the correct position.
Exhaust color is continiously
"BLACK"
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Adjust carburetor.
Poor carburetor adjustment
"engine runs too rich?
TABLE 4. MIXER TROUBLESHOOTING
POSSIBLE PROBLEM
Broken connector pin?
SYMPTOM
SOLUTION
Replace connector pin. Use P/N 3215 when ordering.
Paddle blades will not rotate.
Excessive weight/material in drum?
Remove some of the material in the drum.
Adjust or replace seals.
Material leaking from drum
ends.
Worn or defective paddle shaft
seals?
Malfunction in air-cleaner system,
air filter clogged?
Clean or replace air filter.
Drum difficult to discharge (tilt).
Loss of power.
Defective or worn drum support
brackets?
Apply grease to bracket or replace.
Blades adjusted too tight?
Low hydraulic fluid
Adjust blades until they almost touch side walls of drum.
Check hydraulic fluid sight glass. Add fluid if low.
PAGE 20 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — NOTE PAGE
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts book.
Section 1: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Section 2: Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial number
range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model number
or model number variant.
Section 3: Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+
, %, or
*
I
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
NOTE
The contents of this parts catalog are subject to
change without notice.
PAGE 22 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER— SUGGESTED SPARE PARTS
MS40H 1TO 3 UNITS
MS40H 5TO 10 UNITS
Qty.
P/N
Description
Qty.
P/N
Description
6 ............ 491010 ............ RUBBER LATCH ASSY.
1 ............ EM200293 ....... PADDLE ARM TOW SIDE
1 ............ EM200294 ....... PADDLE ARM CENTER TOW SIDE
1 ............ EM200295 ....... PADDLE ARM CENTER ENGINE SIDE
1 ............ EM200296 ....... PADDLE ARM ENGINE SIDE
3 ............ EM200863 ....... RUBBER BLADE KIT (STEEL DRUM)
2 ............ EM200297 ....... U-BOLT
10 .......... 491010 ............ RUBBER LATCH ASSY.
2 ............ EM200293 ....... PADDLE ARM TOW SIDE
2 ............ EM200294 ....... PADDLE ARM CENTER TOW SIDE
2 ............ EM200295 ....... PADDLE ARM CENTER ENGINE SIDE
2 ............ EM200296 ....... PADDLE ARM ENGINE SIDE
6 ............ EM200863 ....... RUBBER BLADE KIT (STEEL DRUM)
4 ............ EM200297 ....... U-BOLT
2 ............ EM200268 ....... U-BOLT
4 ............ EM200268 ....... U-BOLT
2 ............ 3530 ................ PADDLE SHAFT, SEAL KIT
2 ............ EM902153 ....... BEARING, PADDLE SHAFT
3 ............ 3215 ................ CONNECTOR BOLT
4 ............ 3530 ................ PADDLE SHAFT, SEAL KIT
4 ............ EM902153 ....... BEARING, PADDLE SHAFT
5 ............ 3215 ................ CONNECTOR BOLT
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
PAGE 24 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO
PART NO
EM948423
924801
PART NAME
QTY.
2
1
REMARKS
1
DECAL : CAUTION
*
2
DECAL : SAFETY INSTRUCTIONS
*
3
PLATE, SERIAL NO............................. 1 ........ CONTACT MQ PARTS DEPT. W/MODEL & S/N
4
TBD
DECAL : MQ STOW
1
2
1
1
*
5
DCL151
13238
511764
DECAL : INSPECT TOWING
DECAL : DUMP CONTROL
DECAL : DRIVE CONTROL
*
6
*
7
*
SEE DECAL ILLUSTRATIONS ON PAGE 6.
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — ENGINE END PADDLE ASSY.
ENGINE END PADDLE ASSY.
PAGE 26 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — ENGINE END PADDLE ASSY.
ENGINE END PADDLE ASSY.
NO
3
PART NO
EM200296
EM200295
0300B
PART NAME
QTY.
1
REMARKS
PADDLE ARM ENGINE END
PADDLE ARM CENTER ENGINE END
FLAT WASHER 5/16
4
1
5
28
14
2
6
0161D
HEX NUT 5/16
7
8
9
#
EM203433
0161C
1207
END BACK-UP BLADE
LOCK WASHER 5/16
HHCS 5/16-18 1 3/4"
*
14
14
8
11
12
13
14
15
16
17
18
EM200292
EM200297
EM200268
EM203432
5054A
PADDLE ARM INSERT CASTING
END PADDLE U-BOLT
CENTER PADDLE J-BOLT
CENTER BACK-UP BLADE
LOCK WASHER 1/2"
HEX NUT 1/2-13
SIDE RUBBER BLADE
END RUBBER BLADE
2
2
#
4
*
8
968011
8
EM200212
EM200213
EM200863
4
*
*
2
RUBBER BLADE KIT (STEEL DRUM ONLY)..... 1 ........ INCLUDES ITEMS W/ AND MTG. HDW.
*
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER —TOW END PADDLE ASSY.
TOW END PADDLE ASSY.
PAGE 28 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER —TOW END PADDLE ASSY.
TOW END PADDLE ASSY.
NO
1
PART NO
EM200293
EM200294
0300B
PART NAME
QTY. REMARKS
PADDLE ARM TOW END
PADDLE ARM CENTER TOW END
FLAT WASHER 5/16
1
1
2
5
28
14
2
6
0161D
HEX NUT 5/16
7
8
9
#
EM203433
0161C
1207
END BACK-UP BLADE
LOCK WASHER 5/16
*
14
14
8
HHCS 5/16-18 1 3/4"
11
12
13
14
17
18
19
20
EM200292
EM200297
EM200268
EM203432
5054A
PADDLE ARM INSERT CASTING
END PADDLE U-BOLT
CENTER PADDLE U-BOLT
CENTER BACK-UP BLADE
LOCL WASHER 1/2"
2
2
#
4
*
8
968011
HEX NUT 1/2-13
SIDE RUBBER BLADE
END RUBBER BLADE
8
EM200212
EM200213
EM200863
EM203028
4
*
*
2
RUBBER BLADE KIT (STEEL DRUM ONLY)........ 1 ..... INCLUDES ITEMS W/ AND MTG. HDW.
HDW. KIT, (FOR RUBBER BLADES) .................... 1 ..... INCLUDED IN BLADE KITS
*
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — STEEL MIXING DRUM ASSY.
STEEL MIXING DRUM ASSY.
PAGE 30 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — STEEL MIXING DRUM ASSY.
STEEL MIXING DRUM ASSY.
NO
1
PART NO
203449
7170
PART NAME
MOVEABLE GRATE
CLIP
FLAT WASHER 1/2 USS
GRATE LATCH BAR
LOCK NUT 1/2-13
FLAT WASHER 1/2
CAP, ZERK FITTING
ZERK FITTING
SCREW, HHCS 1/2-13 X 1-3/4
FRONT DUMP SUPPORT BRACKET
DUST CAP
SCREW HHCS 12-13 X 1-1/2
COTTER KEY
QTY.
1
REMARKS
2
1
3
13211
13276Y
10176
0447
1
1
4
5
13
5
6
7
1162A
2621
4
8
4
9
3242
4
10
11
12
13
13260Y
3249
1
1
5218
9
924015
2
WITHOUT HYDRAULIC DUMP
BEARING HOUSING REAR
WITH HYDRAULIC DUMP
BEARING HOUSING REAR
MANUAL DUMP
14
14
511852Y
3291Y
1
1
15
16
17
18
19
20
21
22
23
24
13228
3327
CLEVIS PIN (W/DUMP)
DUMP CYLINDER
1
1
1
1
1
1
1
13259Y
3413
REAR DUMP SUPPORT BRACKET
LOCK NUT 1-8
13286
13285
8151
SPACER
SCREW, HHCS 1-8 X 8
FLAT WASHER
512245Y
EM201537Y
3291
STEEL DRUM W/GRATES ................................. 1 ........ S/N GE210001
MANUAL DUMP HANDLE .................................. 1 ........ DO NOT USE WITH HYDRAULIC DUMP
YBEARING HOUSING FRONT.......................... 1 ........ S/N GE210001
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYD. MIXER — PADDLE SHAFT ASSY.
STEEL PADDLE SHAFT ASSY.
PAGE 32 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYD. MIXER — PADDLE SHAFT ASSY.
STEEL PADDLE SHAFT ASSY.
NO
1
PART NO
3061
PART NAME
SPACER
QTY. REMARKS
14
2
3494
OUTER SEAL
INNER SEAL
SPRING
2
*
3
3019
4
*
4
3024
2
5
13002
3131
BEARING SEAL
O-RING
2
6
2
7
EM902153
3347
BALL BEARING
SPECIAL NUT
SPACER
2
8
1
9
13108
13156
3215
3047
8164
5028B
13257
13156
3530
1
10
11
12
13
14
15
16
COUPLER
1
HHCS 1/2-13 X 3.1/2"
SPACER
1
1
1
1
1
1
CASTLE NUT 1-20
COTTER PIN
PADDLE SHAFT
DRIVE COUPLER
PADDLE SHAFT SEAL KIT .................................... 1 .... INCLUDES ITEMS W/
*
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — HYDRAULIC ASSY.
HYDRAULIC ASSY.
PAGE 34 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — HYDRAULIC ASSY.
HYDRAULIC ASSY.
NO
1
PART NO
3323
PART NAME
QTY.
REMARK
HYDRAULIC MOTOR
FITTING, STRAIGHT W/O-RING
MOTOR HOSE, 16"
SPACER
1
3
1
3
4
1
2
3365
3
13243
3231
4
5
3242
HHCS 1/2-13 X 1.3/4"
LOCK NUT 3/8-16
6
10133
3327
7
DUMP CYLINDER....................................... 1 ....... WITH DUMP (HYDRAULIC DUMP CYLINDER)
8
0131A
0181B
3353
HHCS 1/4-20 X 3/4"
LOCK WASHER 1/4"
OIL FILLER CAP
2
2
1
9
10
11
12
13
14
15
16
17
18
19
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
3369
FITTING, 90 DEG. ...................................... 2 ....... WITH DUMP (HYDRAULIC DUMP CYLINDER)
10136
13198
13153
13196
3367
FLAT WASHER 3/8"
CYLINDER HOSE ....................................... 2 ....... WITH DUMP (HYDRAULIC DUMP CYLINDER)
CAP
VALVE PRESSURE HOSE ......................... 1 ....... GAS ENGINE ONLY
2
2
FITTING, 90 DEG. 3/4" HOSE BARB
TANK RETURN HOSE
SHSS 5-16-24 X 1/2"
OIL FILTER ASSY.
2
3
2
1
1
1
6
1
2
1
2
1
1
1
1
3462
0857
8051
8163
OIL FILTER
3461
FITTING, 45 DEG. 3/4" HOSE BARB
HOSE CLAMP
3333
13219
13220
13210
13213
13147
3336
FITTING 90 DEG.
FITTING
STRAINER
URETHANE SPRING
MOTOR TORQUE ARM
OIL SIGHT GAUGE
HHCS 1/2-13 X 1.3/4"
DRIVE COUPLER
3215
13156
3322
FITTING, 90 DEG. W/O-RING.................... 1 ....... GAS ENGINE ONLY
1284
HHCS 3/8-16 X 1.3/4"
LOCK WASHER 3/8"
3
3
0166A
3316
VALVE ASM ................................................. 1 ....... WITH DUMP (HYDRAULIC DUMP CYLINDER)
13217
10176
3321
HHCS 3/8-16 X 6"
LOCK NUT 1/2-13
1
5
FITTING, 45 DEG. W/O-RING.................... 2 ....... WITH DUMP (HYDRAULIC DUMP CYLINDER)
3314
FITTING, STRAIGHT W/O-RING
MOTOR HOSE 22"
FITTING 90 DEG W/O-RING
FITTING 90 DEG STRAIGHT EL
HANDLE
2
1
1
1
1
1
1
2
1
13244
13216
510263
13225
13226
13212
3407
HANDLE
GROMMET
KNOB
10477
SEAL KIT (DUMP CYLINDER)
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — FRAME 3 ASSY.
FRAME 3 ASSY.
5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
S/N GE21000 -
PAGE 36 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — FRAME 3 ASSY.
FRAME 3 ASSY.
5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE)
NO
1
PART NO
13212
PART NAME
QTY. REMARK
GROMMET ............................................................. 1 .... WITH DUMP (HYDRAULIC DUMP CYL.)
LUG NUT
MAIN FRAME
LOCK NUT 3/8-16
FLAT WASHER 1/2"
LOCK NUT 1/2-13
GRATE LATCH
HHCS 3/8-16 X 1.1/4"
DRUM LOCK LEVER .............................................. 1 .... W/O DUMP (MANUAL ONLY)
HANDLE GRIP ........................................................ 1 .... W/O DUMP (MANUAL ONLY)
DUST CAP
SAFETY CHAIN ASM
U-BOLT
HHCS 1/2-13 X 3.1/2"
TOW BAR (LOOP)
TOW BAR (1 " PIN)
TWO BAR (BALL HITCH 2 -INCH)
AXLE
2
EM941280
13365Y
10133
8
1
3
4
1
5
0447
10176
1
6
12
1
7
511493Y
1023
8
1
9
13280Y
3102Y
10
11
12
13
14
15
15
15
16
17
18
19
20
21
22
23
24
25
26
27
28
30
31
EM941278
3148
2
1
2
1
1
1
1
1
4
2
2
2
2
2
2
2
4
4
2
2
2
2
3028
3215
HLC-1
HPC-1
HBC-1
511699
5218
HHCS 1/2-13 X 1.1/2"
HHCS 1/2-13 X 6"
AXLE SPRING
3043
3076
3018
LEAF SPRING
19045
WHEEL & TIRE
EM968302
0183
CASTLE NUT
COTTER PIN
EM923161
EM903168
EM903169
EM914324
EM941277
EM903113
EM903012
FLAT WASHER 3/4"
BEARING CONE INNER
BEARING CUP INNER
SEAL
HUB W/BEARING CUPS (4-LUG)
BEARING CONE OUTER
BEARING CUPS OUTER
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — ENGINE COVER ASSY.
ENGINE COVER ASSY.
PAGE 38 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — ENGINE COVER ASSY.
ENGINE COVER ASSY.
NO
PART NO
511580Y
509726Y
491010
1284
PART NAME
ENGINE COVER-STEEL
LATCH PIN ASSY.
RUBBER LATCH ASSY.
SCREW, HHCS 3/8-16 X 1.1/2”
FLAT WASHER 3/8”
QTY.
REMARKS
1
1
2
2
4
8
2
3
4
5
4001
6
10133
LOCK NUT 3/8-16
4
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — ENGINE ASSY.
ENGINE ASSY.
PAGE 40 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — ENGINE ASSY.
ENGINE ASSY.
NO
1
PART NO
GX390K1QX2
3396
10133
1475
1665
10136
0310
0622C
3325
2126
13374
3419
PART NAME
HONDA ENGINE 13 HP
KILL BUTTON
LOCK NUT 3/8-16
WIRE CONNECTOR
HHCS 3/8-16 X 2"
FLAT WASHER 3/8"
SQ. KEY 1/4 X 1/4 X 1.1/2"
SHSS 5/16-18 X 1/2"
QTY. REMARK
1
1
4
1
4
4
1
2
1
2
1
1
1
1
6
6
1
2
3
4
5
6
7
8
9
PUMP MOUNT
10
11
12
13
14
15
16
17
SQ. KEY 3/16 X 3/16 X 13/16"
HDRAULIC PUMP SINGLE SHAFT
COUPLER (ENGINE END)
COUPLER INSERT
COUPLER (PUMP END)
LOCK WASHER 3/8"
3418
3420
0166A
1023
EM203149
HHCS 3/8-16 X 1.1/4"
MUFFLER PIPE
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — 1f- 5 HP ELECTRIC MOTOR ASSY.
SINGLE PHASE, 5 HP ELECTRIC MOTOR ASSY.
PAGE 42 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — 1f- 5 HP ELECTRIC MOTOR ASSY.
SINGLE PHASE, 5 HP ELECTRIC MOTOR ASSY.
NO
1
2
3
4
5
6
PART NO
3414
1023
0166A
0205
13291
8133
PART NAME
QTY.
REMARK
5 HP ELECTRIC MOTOR (SINGLE PHASE)
SCREW, HHCS 3/8-16 X 1-1/4
LOCK WASHER 3/8
SCREW, HHCS 3/8-16 X 1
SWITCH MOUNTING PLATE
SCREW, RHMS 8-32 X 3/4
SQUARE KEY 1/4 X 1/4 X 1-1/2
SCREW, 5/16 -18 X 1/2
SWITCH BOX (3 PHASE)
HEATER ELEMENT ........................................................ 3 ............. INCLUDES ITEM W/
MOTOR MOUNT BLOCK
COUPLER (MOTOR END)
COUPLER INSERT
COUPLER (PUMP END)
PUMP MOUNT
1
2
4
2
1
3
1
2
1
7
8
0310
0622C
940228
940198
13292
3421
3418
3420
3416
5054A
2691
13375
2203
10019
8156
10136
1665
10133
9
*
*
10
11
12
13
14
15
16
17
18
19
20
21
22
23
2
1
1
1
1
4
4
1
6
3
2
8
2
4
LOCK WASHER 1/2
SCREW, HHCS 1/2 -13 X 1
HRDRAULIC PUMP SINGLE SHAFT
FLAT WASHER #10
LOCK NUT 10-32
SCREW, HHCS 3/8-16 X 2-1/2
FLAT WASHER 3/8
SCREW, HHCS 3/8-16 X 2
LOCK NUT 3/8-16
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — 3f- 5 HP ELECTRIC MOTOR ASSY.
THREE PHASE, 5 HP ELECTRIC MOTOR ASSY.
PAGE 44 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-40H HYDRAULIC MIXER — 3f- 5 HP ELECTRIC MOTOR ASSY.
THREE PHASE, 5 HP ELECTRIC MOTOR ASSY.
NO
1
PART NO
3481
PART NAME
QTY.
1
REMARK
5 HP ELECTRIC MOTOR (THREE PHASE)
SCREW, HHCS 3/8-16 X 1-1/4
LOCK WASHER 3/8
2
1023
2
3
0166A
0205
4
4
SCREW, HHCS 3/8-16 X 1
SWITCH MOUNTING PLATE
SCREW, RHMS 8-32 X 3/4
SQUARE KEY 1/4 X 1/4 X 1-1/2
SCREW, 5/16 -18 X 1/2
2
5
13291
8133
1
6
3
7
0310
1
8
0622C
940228
940198
13289
3421
2
9
SWITCH BOX (3 PHASE)
HEATER ELEMENT .............................................. 3 ............ INCLUDED W/
MOTOR MOUNT BLOCK
COUPLER (MOTOR END)
COUPLER INSERT
COUPLER (PUMP END)
PUMP MOUNT
LOCK WASHER 1/2
1
*
*
10
11
12
13
14
15
16
17
18
19
2
1
1
1
1
4
4
1
6
3
3418
3420
3416
5054A
2691
SCREW, HHCS 1/2 -13 X 1
HYDRAULIC PUMP SINGLE SHAFT
FLAT WASHER #10
13375
2203
I
10019
LOCK NUT 10-32
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: July 1, 2000
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
4. Freight is at the sender’s expense. All PRICINGANDREBATES
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
Terms of payment for parts are net 10 days.
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspecific
5. Parts must be in new and resalable dateandallordersreceivedonorafterthatdate
condition,intheoriginalMultiquippackage will be billed at the revised price. Rebates for
(ifany),andwithMuiltiquippartnumbers price declines and added charges for price
FREIGHT POLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifest has been obtained from the carrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
clearly marked.
increaseswillnotbemadeforstockonhandat
the time of any price change.
6. Thefollowingitemsarenotreturnable:
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
a. Obsolete parts. (If an item is listed
in the parts price book as being
replaced by another item, it is
obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
andotherrubberparts)thatwere
purchasedmorethansixmonths
priortothereturndate.
MINIMUMORDER
SPECIAL EXPEDITING SERVICE
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meetingthisrequirement.
A$20.00to$50.00surchargewillbeaddedto
theinvoiceforspecialhandlingincludingbus
c. Anylineitemwithanextendeddealer shipments, insured parcel post or in cases
netpriceoflessthan$5.00.
where Multiquip must personally deliver the
partstothecarrier.
d. Special order items.
RETURNED GOODS POLICY
e. Electricalcomponents.
Returnshipmentswillbeacceptedandcredit
will be allowed, subject to the following
provisions:
LIMITATIONS OF SELLER’S LIABILITY
f.
Paint, chemicals, and lubricants.
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
itemwithrespecttowhichdamagesareclaimed,
andinnoeventshallMultiquipbeliableforloss
of profit or good will or for any other special,
consequentialorincidentaldamages.
g. Decalsandpaperproducts.
h. Items purchased in kits.
1. AReturnedMaterialAuthorizationmust
beapprovedbyMultiquippriortoshipment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Sales that defines item numbers,
quantities,anddescriptionsoftheitemsto
bereturned.
8. Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within5days,thematerialwillbereturned
tothesenderathisexpense.
LIMITATIONOFWARRANTIES
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
Nowarranties,expressorimplied,aremadein
connection with the sale of parts or trade
accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connectionwiththesaleofitsproducts.Apart
fromsuchwrittenstatementofwarranty,there
arenowarranties,express,impliedorstatutory,
which extend beyond the description of the
productsonthefacehereof.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s) or invoice(s) under which
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberoftheperson
requestingtheRMA.
3. A copy of the Return Material
Authorizationmustaccompanythereturn
shipment.
PAGE 46 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV. #1 (05/17/02) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
^6668
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|