OPERATION AND PARTS MANUAL
MODEL MS-63
PLASTER AND MORTAR MIXER
(GASOLINE ENGINE/ELECTRIC MOTOR)
Revision #5 (03/26/10)
To find the latest revision of this
publication, visit our website at:
www.stowmfg.com
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — TABLE OF CONTENTS
STOW MS-63 — Plaster/Mortar
HONDA GX160K1QMX2HX2
ENGINE
Air Cleaner Assembly .............................................. 58-59
Mixer
Proposition 65Warning ................................................... 2
Table Of Contents ........................................................... 4
Camshaft Assembly ................................................ 60-61
Parts Ordering Procedures ............................................. 5
Carburetor Assembly ............................................... 62-63
Specifications ................................................................. 6
Control Assembly .................................................... 64-65
Dimensions..................................................................... 7
Crankcase Cover Assembly .................................... 66-67
Safety Messages Alert Symbols................................. 8-9
Crankshaft Assembly .............................................. 68-69
Rules For Safe Operation ........................................ 10-11
Cylinder Barrel Assembly ........................................ 70-71
Towing Guidelines ......................................................... 12
Cylinder Head Assembly ......................................... 72-73
Safety Chain Connection .............................................. 13
Fan Assembly ......................................................... 74-75
Operation and Safey Decals......................................... 14
Flywheel Assembly ................................................. 76-77
General Information ...................................................... 15
Muffler Assembly .................................................... 78-79
Basic Mixer Components ............................................. 16
Fuel Tank Assembly ................................................ 80-81
Basic Engine Components ........................................... 17
Ignition Coil Assembly............................................. 82-83
Electric Motor .......................................................... 18-19
Piston Assembly ..................................................... 84-85
Paddle Blade Adjustment ............................................. 20
Recoil Starter Assembly ......................................... 86-87
Inspection ................................................................ 21-22
Gear Reduction Assembly....................................... 88-89
Start-up Procedures ................................................ 22-24
Labels ...................................................................... 90-91
Operation and Shut-Down ............................................. 25
Maintenance (Engine) .............................................. 26-27
Maintenance (Mixer) ................................................ 28-32
Troubleshooting (Engine) ......................................... 33-34
Troubleshooting (Mixer/Electric Motor) ......................... 35
HONDA GX240K1HA2 ENGINE
Air Cleaner Assembly .............................................. 92-93
Electric Motor Wiring Diagram ...................................... 36
Camshaft Assembly ................................................ 94-95
Explanation of Code In Remarks Column ..................... 38
Carburetor Assembly ............................................... 96-97
Suggested Spare Parts ................................................ 39
Control Assembly .................................................... 98-99
Crankcase Cover Assembly .................................100-101
Crankshaft Assembly ...........................................102-103
Cylinder Barrel Assembly .....................................104-105
Cylinder Head Assembly ......................................106-107
Fan Assembly ......................................................108-109
Flywheel Assembly ..............................................110-111
Muffler Assembly .................................................112-113
Fuel Tank Assembly .............................................114-115
Ignition Coil Assembly..........................................116-117
Piston Assembly ..................................................118-119
Recoil Starter Assembly ......................................120-121
Gear Reduction Assembly....................................122-123
Labels ...................................................................124-125
Component Drawings
Nameplate and Decals ............................................ 40-41
Frame Assembly ..................................................... 42-43
Paddle Shaft Assembly ........................................... 44-45
Steel Drum Assembly ............................................. 46-47
Drum and Paddle Shaft Complete Assembly........... 48-49
Axle Assembly ........................................................ 50-51
Engine Assembly .................................................... 52-53
Electric Motor Assembly ......................................... 54-55
Cabinet Assembly ................................................... 56-57
Terms and Conditions of Sale — Parts ................ 126
Specifications and are
subject to change without
notice.
NOTE
PAGE 4 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealer account number
❒
❒
❒
❒
❒
❒
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
Note: Unless otherwise indicated by customer, all
FedEx or UPS Second Day or Third Day orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order
is received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
FedEx or UPS Next Day
Federal Express Priority One
DHL
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number
on hand when calling.
(Domestic USA Dealers Only)
STOW MAIN OFFICE
18910 Wilmington Ave.
Carson, CA 90746
800-421-1244
FAX: 310-537-3927
Extra Discounts!
All parts orders which include complete part numbers and
are received by our automated web parts order system, or
by fax qualify for the following extra discounts:
Email: stow@stowmfg.com
Internet: www.stowmfg.com
Ordered
Standard
Stock orders
SALES DEPARTMENT
310-661-4242
877-289-7869 (877-BUY-STOW)
PARTS DEPARTMENT
800-427-1244
310-537-3700
SERVICE DEPARTMENT
800-478-1244
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
via
orders
($750 list and above)
Fax: 310-604-9237
Fax
3%
5%
10%
10%
Web
FAX: 800-672-7877
FAX: 310-637-3284
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other
FAX: 310-537-4259
FAX: 310-631-5032
FAX: 310-537-1173
carrier.
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
310-537-3700, EXT. 279
**Common nuts, bolts and washers (all items under $1.00
list price) do not count towards the 10+ line items.
NOTE: DISCOUNTS ARE SUBJECT TO CHANGE
Direct TOLL-FREE access
to our Parts Department:
STOW CONSTRUCTION EQUIPMENT
A DIVISION OF MULTIQUIP INC.
Toll-free nationwide — 800-427-1244
POST OFFICE BOX 6254
888-252-STOW [888-252-7869]
FAX: 310-537-1986
CARSON, CA 90749
310-537-3700
FAX: 800-556-1986
Toll-free FAX — 800-6-PARTS-7 (800/672-7877)
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — SPECIFICATIONS
TABLE 1. MIXER SPECIFICATIONS
Capacity
Bag Capacity
Weight
6.3 cu. ft (178 liters)
1-1/2 to 2-1/2 bags
574 lbs. (260 kg.)
73 in. (185 cm.)
17.5 in. (44.45 cm.)
V-Belt/Gear
Height W/Dump Handle
Discharge Height
Drive
Dump Action
Manual
TABLE 2. SPECIFICATIONS (ENGINE & ELECTRIC MOTOR)
Model
HONDA GX160K1HX2
HONDA GX240K1HA2
BALDOR 35L229S302
Air-cooled 4 stroke, Horizontal
1.5 HP, 115/230, Single
Phase Electric Motor
Type
Shaft Gasoline Engine
2.51 in. X 1.65 in.
(63.8 mm x 42 mm)
2.90 in. X 2.30 in.
(73 mm x 58 mm)
Bore X Stroke
N/A
Displacement
Max Output
8.75 cc
14.81 cc
N/A
5.5 HP/3600 R.P.M
8.0 H.P./3600 R.P.M.
1.5 H.P./1725 RPM
Engine/Electric
Motor
.951 Gallons
(3.6 Liters)
Approx. 1.59 U.S. Gallons
(6 Liters)
Fuel Tank Capacity
N/A
Fuel
Unleaded Gasoline
N/A
N/A
Lube Oil Capacity
2-1/3 pints
Centrifugal Fly-weight Type
Recoil Start
Speed Control
Method
N/A
N/A
Starting Method
12.2 x 14.2 X 13.8 in.
(312 X 362 X 335 mm)
14.0 x 16.9 X 16.1 in.
(355 X 430 X 410 mm)
13.3 x 8.7 X 9.06 in.
(338 X 220 X 230 mm)
Dimensions (L x W x H)
Dry Net Weight
33 lbs. (15 Kg.)
55.1 lbs. (25 Kg.)
Approx. 22 lbs. (10 Kg.)
In accordance with our established
policy of constant improvement, we
reserve the right to amend these
specifications at any time without
notice.
PAGE 6 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — DIMENSIONS
TABLE 3. DIMENSIONS
Description
Dimensions in. (cm)
Length
(w/ Tow Bar)
67 in. (170 cm)
Width
50 in. (127 cm)
56 in. (142 cm)
Height
Figure 1. Dimensions
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Potential hazards associated with the operation of a MS-63
Plaster/Mortar Mixer will be referenced with Hazard Symbols
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
which appear throughout this manual, and will be referenced
Lethal Exhaust Gases
in conjunction with Safety Message Alert Symbols.
Lethal Exhaust Gas Hazards
WARNING
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
operation of the STOW Model MS-63
mortar and plaster mixer. Refer to the
engine manufacturers instructions for
data relative to its safe operation.
Before using this mixer, ensure that the operating individual
has read and understands all instructions in this manual.
Explosive Fuel Hazards
SAFETY MESSAGE ALERT SYMBOLS
WARNING
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
Burn Hazards
WARNING
WARNING
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Respiratory Hazards
WARNING
ALWAYS wear approved respiratory
protection when required.
PAGE 8 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — SAFETY MESSAGE ALERT SYMBOLS
Equipment Damage
Rotating Parts Hazards
CAUTION
CAUTION
Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your light tower, other
property, or the surrounding environment.
Accidental Starting Hazards
CAUTION
ALWAYS disconnect the electrical power
cord from the electric motor when the mixer
is not in use and place the ON/OFF switch
in the OFF position.
Eye and Hearing Hazards
CAUTION
ALWAYS wear approved eye and
hearing protection.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or mixer.
Read this manual!
DANGER
Failure to follow instructions in this manual may lead
to serious injury or even death! This equipment is to
be operated by trained and qualified personnel only!
This equipment is for industrial use only.
The following safety guidelines should always be used when
operating the STOW MS-63 mortar and plaster mixer:
■
■
High Temperatures – Allow the engine to cool before
adding fuel or performing service and maintenance
functions. Contact with hot! components can cause
serious burns.
GENERAL SAFETY
■
DO NOT operate or service this
equipment before reading this entire
manual.
The engine section of this mixer requires an adequate
free flow of cooling air. NEVER operate the mixer in any
enclosed or narrow area where
free flow of the air is restricted.
If the air flow is restricted it
will cause serious damage to
the mixer or engine and may
cause injury to people.
■
■
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
Remember the mixer's engine
gives off DEADLY carbon monoxide gas.
■
■
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result from
fuel vapors, or if fuel is spilled on a hot
engine.
NEVER operate this equipment under the influence of
drugs or alcohol.
■
■
NEVER operate the mixer in an
explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■
ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the mixer.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■
■
■
■
NEVER place hands inside the drum while the blades
are rotating.
■
■
■
Stop the engine when leaving the mixer unattended.
Block the unit when leaving or when using on a slope.
Maintain this equipment in a safe operating condition at
all times.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacture does not assume responsibility for any
accident due to equipment modifications.
Starting the Mixer Engine
WARNING
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
NEVER! start the engine or engage the paddle arms
when the drum is in the discharge (down) position.
PAGE 10 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — RULES FOR SAFE OPERATION
TRANSPORTING
■
■
■
■
ALWAYS stop the engine before servicing, adding fuel
and oil.
NEVER run engine without air filter. Severe engine may
occur.
ALWAYS service air cleaner frequently to prevent
carburetor malfunction.
ALWAYS check the machine for loosened threads or bolts
before starting.
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
■
Drain fuel when transporting mixer over long distances
or bad roads.
MAINTENANCE
■
NEVER lubricate components or attempt service on a
■
■
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using mixer.
ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children.
running mixer.
■
ALWAYS allow the mixer a proper amount of time to
cool before servicing.
■
■
Keep the mixer in proper running condition.
Fix damage to the mixer immediately and always replace
broken parts.
■
■
DO NOT operate this equipment unless all guards and
safety devices are attached and in place.
■
■
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
CAUTION must be exercised while servicing this
equipment. Rotating and moving parts can cause injury
if contacted.
When towing, an adequate safety chain must be fastened
to the frame.SeeTowing Guidelines section in this manual.
Keep all inexperienced and unauthorized people away
from the equipment at all times.
Unauthorized equipment modifications will void all
warranties.
Check all fasteners periodically for tightness. Also check
towing tongue bolt, lock nut and wheel lug nuts for wear.
DO NOT use food or plastic containers to dispose of
■
■
■
■
■
■
hazardous waste.
EMERGENCIES
■
ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
Stop the engine and disconnect the spark plug before
allowing anybody’s hands in the mixing drum.
NEVER pour or spray water over the engine or electric
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
motor.
Stand Clear of the
Mixer when in use
WARNING
Always stand clear of the dump handle when the mixer
is in operation. Any binding of material between the mixer
blades and the drum will cause the drum handle to quickly
move and could cause bodily harm.
■
Depending on type of mixer, test the ON/OFF switch for
either the gasoline engine or electric motor before operating.
The purpose of these switches is to shut down the engine
or motor of the mixer.
■
Refer to the HONDA Engine Owner's Manual for engine
technical questions or information recommended by
Multiquip for this equipment. Damage to the equipment
and/or injury to user may result.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER —TOWING GUIDELINES
Towing Safety Precautions
■
ALWAYS make sure that the fuel valve lever is in the
OFF position (gasoline models only).
Regularly Inspect
Towing Components
■
Check wheel mounting lug nuts with a torque wrench.
Torque wheel lug nuts as described in the maintenance
section of this manual.
CAUTION
To reduce the possibility of an accident while transporting
the mixer on public roads, always make sure that the
mixer towing components and the towing vehicle are in
good operating condition and both units are mechanically
sound.
■
■
■
Check tightness of U-clamp nuts, torque suspension
hardware as referenced in the maintenance section of
this manual.
Avoid sudden stops and starts.This can cause skidding,
or jackknifing. Smooth, gradual starts and stops will
improve gas milage.
The following list of suggestions should be used when towing
the mixer:
Avoid sharp turns to prevent rolling.
■
Check with your county or state safety towing regulations
department before towing your mixer.
Tow Bar toVehicle Connection (Coupler Only)
■
Make sure that the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).
1. Check the vehicle hitch ball, and mixer's coupler for
signs of wear or damage. Replace any parts that are
worn or damaged before towing.
■
■
ALWAYS inspect the hitch and coupling for wear.NEVER
tow the mixer with defective hitches, couplings, chains
etc.
Replacing
CAUTION
Towing Components
CHECK the tire air pressure on both the towing vehicle
and the trailer. Also check the tire tread wear on both
vehicles.
If the mixer tow bar is deformed or damaged, replace the
entire tow bar. NEVER tow the mixer with a defective
tow bar.There exists the possibility of the mixer separating
from the towing vehicle.
■
■
■
■
ALWAYS make sure the mixer is equipped with a "Safety
Chain".
2. Use only a 2-inch ball diameter (towing vehicle), this will
match the mixer's 2-inch coupler. Use of any other ball
diameter will create an extremely dangerous condition
which can result in separation of the coupler and ball or
ball failure.
ALWAYS attach trailer's safety chain to the frame of
towing vehicle.
ALWAYS make sure that the towing vehicle's directional,
backup, and brake lights are working properly.
Remember in most cases the maximum speed unless
otherwise posted for highway towing is 55 MPH, however
before towing your mixer, check your local state, and
county vehicle towing requirements. Recommended off-
road towing is not to exceed 10 or 15 MPH or less
depending on type of terrain.
3. After tow bar has been connected to mixer (see next
page), attach mixer's coupler to the hitch ball on the
towing vehicle securely and make sure the lock lever is
in the down position (locked).
Mixer Tow Bar Vehicle Connection (Pintle and Loop)
1. Make sure the bumper on the towing vehicle is equipped
to handle either a pintle or loop type tow bar configuration.
■
Place chocked blocks underneath wheels to prevent
rolling, while parked, if disconnected from towing
vehicle.
2. After tow bar has been connected to mixer (see next
page), secure either type of tow bar to the towing vehicle,
following state and county towing regulations.
■
■
Inflate tires to correct pressure, inspect tires for cuts,
and excessive wear.SeeTable 9 (TireWearTroubleshooting).
3. As a minimum, use a 1/2-inch bolt and nylock nut grade
5 when securing the tow bar to the towing vehicle and to
the unit being towed.
When towing of the mixer is required, place the drum in
the up position (mouth facing upwards) and lock the drum
latch.
PAGE 12 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — SAFETY CHAIN CONNECTION
2. Route the safety chain through the holes just above the
Always Tow with
a Safety Chain
CAUTION
tow bar, located on each side of the mixer stand.
Loop the chain together and place under the tow bar.
Secure the loop with the connector link.
NEVER! tow the mixer with the safety chain removed.
The safety chain is intended to prevent complete
3. extend the safety chain along the length of the tow bar,
looping it through the tow bar's connector link. Remove
any excess chain slack.
separation of the mixer from the towing vehicle in the
event of a tow bar failure.
Reference Figure 2 for the installation of the safety chain.
4. Connect the free end of (clevis safety hook) the safety
chain to the towing vehicle. Remember it is critical that
the length of the chain be properly adjusted, to prevent
the draw bar and the front of the mixer stand from
dropping to the the ground (contact) in the event the
draw bar becomes disconnected from the towing vehicle.
Tow Bar to Mixer Connection
1. Insert the tow bar through the round opening at the bottom
of the mixer stand.
Align the hole on the tow bar with the hole on the mixer
frame, and insert 1/2-inch bolt through tow bar and frame.
Secure tow bar to frame with 1/2-inch nylock nut.Tighten
to 40 ft.-lbs.
Drum Saftey
CAUTION
when Towing
DO NOT tow the mixer unless the mixing drum is
completely empty. ALWAYS make sure the drum latch
pin is fully engaged to the right (Figure 3) of the drum
stop block. This will keep the drum from rotating.
Figure 3. Drum Latch Pin
(Tow or Locked Position)
Figure 2. Tow Bar and Safety Chain Installation
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-63 PLASTER/MORTAR MIXER — OPERATION AND SAFETY DECALS
Machine Safety Decals
The STOW MS-63 mortar and plaster mixer is equipped with a number of safety decals.These decals are provided for operator
safety and maintenance information. Figure 4below illustrates these decals as they appear on the machine. Should any of these
decals become unreadable, replacements can be obtained from your dealer.
Figure 4. Mixer Operation and Safety Decals
PAGE 14 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — GENERAL INFORMATION
Application
Ensure that the extension cable is carefully laid out avoid-
ing wet areas, sharp edges and locations where vehicles
might run over it. Avoid allowing the extension cable to be
trapped underneath the mixer.
The STOW MS-63 series mixers (drum capacity of 7.0 cu. ft./198
liters) are shipped completely assembled and have been factory
tested and are ready for use.
This mixer is only intended for the production of plaster
and mortar. The mixer must be used for its intended purpose
and is not suitable for the mixing of flammable or explosive
substances. The mixer must not be used in an explosive
atmosphere.This mixer has a batch capacity between 2-1/2
and 3-1/2 bags.
Unroll the extension cable fully or it will overheat and could
catch fire. Make sure that all extension cable connections
are dry and safe. Replace any defective or badly worn ex-
tension cable immediately.
Hardware
Check all hardware on the mixer before starting.Periodically
inspect all hardware. Loose hardware can contribute to early
component failure and poor performance. Use Table 4 as
general guideline when torqueing of mixer hardware is
required. Remember to keep all mixer hardware components
tight.
Power Plants
The STOW plaster and mortar mixer can be powered by
either a Honda GX240K1HA2 or GX160K1QMX2HX2 air-
cooled, 4-stroke gasoline engine or a 1.5 HP electric motor.
Refer to Table 2 for specific engine or electric motor data
information.
Table 4. Hardware Torque
Recommendations
Electrical
Hardware
Torque (ft-lbs)
Diameter
If mixer is equipped with an electric motor, make sure that
the power being supplied to the motor corresponds to the
voltage rating label on the motor.Supplying the wrong voltage
to the electric motor will cause severe electrical damage to
the motor.
5/16-inch x 18
3/8-inch x 16
14
24
3/8-inch x 24
1/2-inch x 13
37
39
90
Always make sure the OFF/ON switch on the electric motor
is in the OFF position before applying power.
1/2-inch x 13
(Grade 8)
It is strongly recommended when inserting the mixer's
power cord into a receptacle, that a G.F.C.I. (Ground Fault
Current Interrupter) receptacle be used (115 VAC
applications).
Engine Maintenance
For basic engine maintenance, refer to the engine
maintenance section in this manual. For a more detailed
engine maintenance, refer to the Honda Engine Owner's
manual furnished with the engine.
Extension Cables
The extension cable should be a 3-wire configuration that
includes a ground wire that conforms to UL code. The wire
cross section must be a minimum of 2.5 mm2. Choose an
extension cord of adequate current carrying capacity as ref-
erenced in Table 6. Remember cable distance affects the
current-voltage capacity of the extension cable.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — BASIC MIXER COMPONENTS
8. Mixing Paddles — Used in the mixing of material. This
unit uses four different types of paddles to provide a fast
uniform mix.
9. Bag Cutter—This feature allows compound mixing bags
to be opened easily, therefore allowing the contents of the
bag to fall directly into the mixing drum.
10. Safety Grill — Provided for operator safety.This safety
grill is designed to keep hands and solid objects out of the
mixing drum when in use.This grill should be closed at all
times when mixer is in use. DO NOT remove the grill or
grill opening bar. Keep the grill clean by washing it down
daily.
11. Dump Handle — Pull this handle downward to dump the
contents of the drum. Push the handle upward to return
the drum to its vertical position.
12. Safety Grill Lock Handle — To prevent injury to hands
and arms, the safety grill should ALWAYS be locked when
the mixing of plaster or mortar is required. Also when
transporting the mixer the safety grill should be locked.
The safety grill should only be un-locked when cleaning
of the blades and drum is required.
Figure 5. Mixer Components
Figure 5 illustrates the basic components and controls of
the STOW MS-63 mixer
1. Tires Ply — The tire ply (layers) number is rated in letters;
13. Pivot Point/Zerk Fitting — There is, on each end of the
mixing drum a zerk grease fitting.These fittings lubricate
the dumping mechanism. Lubricate both fittings at least
twice a week.
This mixer uses 13-inch 4-ply tires.
2. Engine Cover — Lift this cover to gain access to the engine
compartment.
3. Belt Slip Lever — When starting this lever should be
move upward and to the left. For mixing place the lever in
the down position. See attached decal located adjacent to
lever.
14. Dump Handle Release Pin — Pull this pin outward
(spring loaded) to release the drum, then pull down on the
dump handle to place the drum in the dump position. When
drum is in dump position, pin will automatically lock drum.
4. ON/OFF Switch (electric) — This switch is provided on
mixers with electric motors.To gain access to this switch,
lift the engine cover.When activated it will shut down the
electric motor.
15. Steel Mixing Drum — Mixing materials such as mortar,
plaster are to be placed into this drum for mixing. Always
clean the drum after each use.
16. Tow Bar/Coupler —This mixer uses a 2-inch coupler or
5. ON/OFF Switch (gasoline) —This switch is provided on
mixers with gasoline engines only and is located on the
side of the engine cover. When activated it will shut down
the engine.
pintle towbar.
17. Safety Chain — This mixer uses a 3/16-inch thick, 72-
inches long zinc-plated saftey chain. ALWAYS connect
the safety chain when towing.
6. Latch — Use this latch to secure the engine compartment
18. Forklift Pockets – When lifting of the mixer is required,
use these fork lift pockets to lift the mixer. Remember
to insert the forks of the forklift a minimum of 24 inches
into the lift pockets.
cabinet.
7. Drum Bearing — There is on each end of the mixing
drum, a sealed bearing. Bearings are packed and sealed
at the factory and require no further maintenance.
19. Chock Blocks — Place these blocks (not included as
part of the mixer package) under each mixer wheel to
prevent rolling.
PAGE 16 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — BASIC ENGINE COMPONENTS
Figure 6. Engine Controls and Components
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
INITIAL SERVICING
the flow of fuel.
The engine (Figure 6) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an air
filter, with a damaged air filter, or a filter
in need of replacement will allow dirt
to enter the engine, causing rapid
engine wear.
Explosive
DANGER
Fuel Hazard
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity
to cool down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel residue
has been completely wiped up, and the area surrounding the
engine is dry.
Burn Hazard
WARNING
Enginecomponentscangenerateextremeheat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
9. Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — ELECTRIC MOTOR
Electric Motor
TABLE 5. ELECTRIC MOTOR WIRING INFORMATION
For maintenance care and operation of the electric motor,
refer to your electric motor instruction booklet furnished with
the motor.
115-230 VAC - Single Phase
Mating NEMA
Motor
Horsepower
Rating
NEMA Plug Connector
L5-20P P/N EM940537
L6-20P P/N 940539
Receptacle Connector
Protect the electric motor from dust as much as possible
and keep ventilating openings clean.
1.5 HP
(115 VAC)
L5-20R P/N EM940538
Electric Motor
1.5 HP
(230 VAC)
L6-20R P/N 940540
CAUTION
Safety
DO NOT spray water at any time on the electric motor.
DO NOT operate electric motor in a explosive environment.
The electric motor used in this mixer is a single-phase 3
HP motor. The input voltage requirement for this motor is
115/230 VAC, and has been pre-set to 230VAC.
Electric Motor Connection
A 12-inch electrical cable (Figure 7) is provided with the
electrical motor for hookup to a power source.Table 5 shows
the required NEMA connector for the desired motor
horsepower rating. In addition, Table 5 also shows the
matching NEMA approved connector for the required
extension cord.
Electric Motor
Connections
CAUTION
ALWAYS make certain that the power source required
for the electric motor is correct and always use the correct
NEMA configuration plug. Failure to supply the correct
voltage to the motor can severely damage the motor.
It is strongly recommended that all
electrical wiring be done by a licensed
electrician.
Figure 7. Single Phase Electric MotorWith
12-inch Pigtail
Special attention should be given to the electric switch as well
as the over-and-under voltage protection devices as per
regulations set forth in the local electrical safety code handbook
PAGE 18 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — ELECTRIC MOTOR
The motor supplied is wired for 115 VAC grounded operation.
Make certain that the correct size grounded (3-wires) extension
cord is used. See Table 6.
TABLE 6. RECOMMENDED EXTENSION CORD SIZES
50 ft.
75 ft.
100 ft.
200 ft.
Model
Motor Voltage
(15.24 m) (22.86 m) (30.48 m) (60.96 m)
Motors can burn out when the line voltage falls 10% below the
voltage rating of the motor. Failure to use proper voltage will
cause the motor to overheat and actuate the overload switch.
115
1.5 HP
No. 12
No. 14
No. 10
No. 12
No. 8
No. 6
No. 8
MS-63
(Electric)
230
No. 12
If overload protection should actuate because of improper voltage
or any other malfunction, turn the main switch on the motor to the
"OFF" position and correct the problem, press the reset switch
button, and turn the main switch to the "ON" position.
Electric MotorVoltage Switch
1. ALWAYS make certain the motor switch is "OFF" and the
power cord has been disconnected from the power source.
2. Remove the voltage lock-out bolt (Figure 7). Change the
position of the voltage change toggle switch from 115
VAC to 230 VAC. The mixer is factory wired for 115 VAC
operation.
3. Replace the voltage lock-out bolt.
4. Important!, when changing the input voltage to the motor
from 115 to 230 VAC, the plug on the motor power cord
must also be changed. SeeTable 5.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 — PADDLE BLADE ADJUSTMENT (STEEL DRUM)
Adjust paddles as shown in Figure 8.
Figure 8. Paddle Blade Adjustment, Steel Drum
PAGE 20 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — INSPECTION
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
Before Starting
1. Read all safety instructions at the beginning of manual.
4. Iftheoillevelislow(Figure10), filltotheedgeoftheoilfiller
holewiththerecommendedoiltype(Table7).Maximum oil
capacityis2.33qts. (1.09liters)
2. Clean the mixer, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
3. Check the air filter for dirt and dust. If air filter is dirty,
replace air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with
dry compressed air.
Reference manufacturer engine
manual for specific servicing
nstructions.
5. Check fastening nuts and bolts for tightness.
Eyesight and Hearing
CAUTION
Protection
ALWAYS wear approved eye and
hearing protection before operating
the mixer.
Inspection &
Maintenance Saftey
CAUTION
NEVER place hands or feet inside the
engine guard cover while the engine is
running. ALWAYS shut the engine down
before performing any kind of maintenance
service on the mixer.
Figure 10. Engine Oil Dipstick (Oil Level)
Table 7. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
Engine Oil Check
1. To check the engine oil level, place the mixer on secure
level ground with the engine stopped.
0°C or Lower
2. Remove the filler dipstick from the engine oil filler hole
(Figure 9) and wipe it clean.
Figure 9. Engine Oil Dipstick (Removal)
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — INSPECTION
V-belt Check
Fuel Check
A worn or damaged V-belt can adversely affect the
performance of the mixer. If a V-belt is defective or worn
simply replace the V-belt as outlined in the maintenance
section of this manual.
Explosive Fuel
DANGER
Hazard
If your mixer has a gasoline engine, determine if the
engine fuel is low. If fuel is low, remove the fuel filler cap
and fill with unleaded gasoline. Motor
fuels are highly flammable and can be
dangerous if mishandled.DO NOT smoke
Blade Check
Check for worn or paddle blades. Make sure that all blades
are adjusted properly. See blade adjustment procedure in
this manual. Replace all defective or damaged blades
immediately.
while refueling.DO NOT attempt to refuel
the mixer if the engine is hot! or running.
1. Remove the gasoline cap located on top of fuel tank.
Controls
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
Start/Stop Switches
This mixer has been equipped with a start/stop switch for
both the gasoline and electric motor mixers.These switches
should be tested every time the engine or electric motor is
started.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
Start/Stop Switch
CAUTION
Grease Fittings (Dumping Mechanism)
NEVER! disable or disconnect the start/stop switch. It is
provided for operator safety.Injury may result if it is disable,
disconnected or improperly maintained.
Check the zerk grease fittings at each end of the mixing
drum. These grease fittings lubricate the dumping
mechanism. If the dumping handle is stiff or hard to move
lubricate these fittings.
PAGE 22 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — START-UP PROCEDURES
2. To start a cold engine, move the choke lever (Figure 12) to
This section is intended to assist the operator with
the initial start-up of the STOW MS-63H (gasoline
engine) or STOW MS-63E (electric motor) mixer.It
is extremely important that this section be read
carefully before attempting to use the mixer in the
field.
the CLOSED position.
DO NOT use your mixer until this section is thoroughly
understood.
General Safety
WARNING
Failure to understand the operation of the STOW MS-63
series mixers could result in severe damage to the mixer
or personal injury.
See Figures 5 and 6 for the location of any control
referenced in this manual.
Figure 12. Choke Lever
3. Move the throttle lever (Figure 13) away from the slow
position, about 1/3 of the way toward the fast position.
Respiratory Hazard
CAUTION
NEVER operate the mixer in a confined
area or enclosed area structure that
does not provide ample free flow of air.
Starting (gasoline only)
The following steps outline the procedure for starting the engine.
Depending on the type of engine employed in the mixer the
steps may vary slightly. If your mixer has an electric motor
disregard this section.
Figure 13.Throttle Lever
1. Move the fuel shut-off lever (Figure 11) to the ON position.
Figure 11. Fuel Shut-OFF Lever
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MS-63 PLASTER/MORTAR MIXER — START-UP PROCEDURES
4. Turn the engine switch (Figure 14) to the ON position.
Preventing Drum Tipping
CAUTION
Make certain the drum lock pin (Figures 17 and 18) is placed
to the RIGHT (when viewing the mixer from the tow-pole
end) of the drum stop block which is welded to the front side
of the drum. Also make sure lock pin is fully engaged (locked).
This will prevent the drum from tipping.
Figure 14. Engine ON/OFF Switch
5. The main start/stop switch located on the engine cover is
(Figure 15) is used to start and stop the engine. Pull this
switch outward to start the engine.
Figure 17. Drum Lock Pin (Side-View)
Figure 15. Start/Stop Switch (gasoline engine)
6. Place the belt slip lever (Figure 16) in the START/STOP
(disengaged) position.
Figure 18. Drum Lock Pin (Right Position)
7. Pull the starter grip (Figure 19) lightly until you feel
resistance, then pull briskly.Return the starter grip gently.
Figure 16. Belt Slip Lever
(Start/Stop Position)
Figure 19. Starter Grip
PAGE 24 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — OPERATION/SHUT-DOWN
8. Place the belt slip lever (Figure 20) in the mix position.
Dump Handle Safety
This will tilt the engine placing tension on the V-belts
enabling the shaft to rotate.
WARNING
Be sure to stand clear of the dump handle (Figure 22)
when the mixer is operational. Any binding of material between
the mixer blades and the drum will cause the drum handle to
move to the discharge position and could cause bodily harm.
Figure 20. Belt Slip Lever (Mix Position)
Starting (electric only)
1. Using an adequate size extension cord (see Table 5),
connect one end of the extension cord to the plug on the
electric motor, connect the other end to the power source.
Make sure the motor is configured for the proper operating
voltage.
2. Set the electric motor's ON/OFF switch (Figure 7) to the
ON position.
Mixing Dumping
1. The paddle shaft inside the drum should be rotating at this
time.
Figure 22. Stand Clear of Dump Handle
STOPPINGTHE MIXER (gasoline engine)
2. Add a small amount water to the mixing drum.
3. Lift the mixing bag compound onto the steel safety grate
over the bag cutter and let the contents fall into the drum.
Add more water if desired and mix compound to desired
consistency.
1. Place the belt slip lever in the start/stop position (Figure
20).
4. When charging, mixing, or dumping a batch of plaster or
mortar the drum lock pin should be placed to the left
(when viewing the mixer from the towpole end) of the drum
stop block which is welded to the front side of the drum.
See Figure 21.
2. Push the main start/stop switch (Figure 15) inward to stop
the engine.
3. Tur n the fuel shut-off valve to the OFF position.
4. Disconnect the spark plug.
5. Clean mixer as referenced in the maintance section of this
manual.
This will allow the operator to use both hands on the drum
handle during dumping. Please note that when the lock pin
is placed to the left, the drum will be maintained in the
vertical position as the paddles rotate. To discharge the
material the operator should hold the dump handle with
both hands and rotate the drum to discharge the desired
amount of material.
STOPPINGTHE MIXER (electric motor)
1. Place the electric motor's ON/OFF switch (Figure 4) in the
OFF position.
2. Disconnect the electric motor's extension cord from its
power source.
3. Clean mixer as referenced in the maintance section of this
manual.
Figure 21. Drum Lock Pin (Left Position)
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — MAINTENANCE (ENGINE)
UseTable 8 as a general maintenance guideline when servicing
your engine. For more detail engine maintenance information,
refer to the engine owner's manual supplied with your engine.
Table 8. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 26 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — MAINTENANCE (ENGINE)
Maintenance
ENGINEAIRCLEANER
Perform the scheduled maintenance procedures as defined by
Table 8 and below:
1. Remove the air cleaner cover and foam filter element as
shown in Figure 25.
DAILY
2. Tap the paper filter element (Figure 25) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
gearbox for oil leaks. Repair or replace as needed.
WEEKLY
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 23), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
Explosive
DANGER
Hazard
DO NOT use gasoline as a cleaning
solvent, because that would create a risk of
fire or explosion.
Figure 23. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 24.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 7. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 25. Engine Air Cleaner
Figure 24. Engine Oil (Draining)
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)
Ball Socket and Clamp Face Maintenance
Lubricating the
CAUTION
Failure to lubricate the drum bearing grease fittings
periodically will cause the dumping mechanism to stiffen,
making the mixing drum hard to dump.
1. If the towing vechicle is equipped with a ball socket, smear
socket periodically with multi-purpose grease. This will keep
the ball socket well lubricated.
Grease Fittings
2. Periodically oil pivot points and clamp face surfaces of
coupler with SAE 30 WT.motor oil.
3. When parking or storing your mixer. Keep the coupler off
the ground so dirt will not build up in the ball socket.
Countershaft Bearing Lubrication
There is 1 set of countershaft bearings (Figure 28) that will
require lubrication. Lubricate the grease fitting for each
countershaft bearing every 40 hours of operation using
any grade lithium base grease.
Drum Head Seals
There is 1 set of drum head seals (Figure 26) that will require
lubrication. Lubricate the grease fitting for each drum seal
every 40 hours of operation using any grade lithium base
grease. Apply grease until visible inside of mixing drum (over
grease). This will purge seal system of contamination.
Figure 28. Grease Fittings (Countershaft)
Wheel Bearings
1. After every 3 months of operation, remove the hub dust cap
and inspect the wheel bearings (Figure 29). Once a year,
or when required, disassemble the wheel hubs remove
the old grease and repack the bearings forcing grease
between rollers, cone and cage with a good grade of high
speed wheel bearing grease (never use grease heavier
than 265 A.S.T.M.penetration (“No.2.”)
Figure 26. Grease Fittings (Drum Head Seals)
Drum Bearing Bracket Lubrication
There is 1 set of drum bearing brackets (Figure 27) that will
require lubrication. These brackets are intended to make
the drum rotate freely. Lubricate the grease fitting for each
drum bearing bracket every month or when the drum
becomes difficult to position using multi-purpose grade
grease.
Figure 29. Wheel Hub and Bearings
Figure 27. Grease Fittings (Dumping Mechanism)
PAGE 28 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)
2. Fill the wheel hub (Figure 28) with grease to the inside
diameter of the outer races and also fill the hub grease cap.
Reassemble the hub and mount the wheel.Then tighten
the adjusting nut, at the same time turn the wheel in both
directions, until there is a slight bind to be sure all the
bearing surfaces are in contact.
INSPECT TOOTH CONTACT BETWEEN MAIN GEAR AND
DRIVE PINION
1. Coat 3 or 4 teeth at 3 different positions on the main gear
with yellow paint.
2. Rotate the drive pulley in both directions.
3. Inspect the tooth pattern.
Then back-off the adjusting nut 1/6 to 1/4 turn or to the
nearest locking hole or sufficiently to allow the wheel to
rotate freely within limits of .001" to .010" end play.Lock the
nut at this position. Install the cotter pin and dust cap, and
tighten all hardware.
4. If gear teeth are not contacting properly (Figure 31), adjust
pillow block to correct the problem.
MAIN GEAR AND DRIVE PINION ALIGNMENT
1. Disconnect the spark plug wire (gasoline engines). If
mixer is equipped with an electric motor remove power
cord from AC power receptacle. In addition make sure
the clutch engagement lever is dis-engaged to relieveV-
belt tension.
2. The countershaft and drive pinion are mounted on a slotted
base.To align drive pinion with main gear, loosen the pillow
block mounting bolts and move them until the necessary
alignment has been made. Remember gears must be
paralleled aligned not skewed.
Figure 31. GearTeeth Alignment
GEAR LUBRICATION
3. Using your hand, slightly move (rock) the drive pulley back
and forth to determine the amount of backlash. Insert feeler
gauge between gears to determine backlash distance.
Backlash should range between 0.007- 0.012 inches
(Figure 30).
The surface of the pinion and main gear (Figure 32) should be
very lightly greased.
Grease main and pinion gears
every 250 hours of operation.
IMPORTANT! avoid over-
greasing. Excess grease will
accumulate contaminates and
cause premature wear.
Figure 30. Drive Pinion and Main Gear (Backlash)
Figure 32. Pinion and Bull Gear Lubrication
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)
Grease Fittings (Zerk) Maintenance (Electric Motor)
Tires Wear/Inflation
1. There are two grease (Figure 33) fittings at each end of the
electric motor that will require lubrication. Lubricate these
fittings about every 16 months.
Tire inflation pressure is the most important factor in tire
life. Pressure should be checked cold before operation. DO
NOT bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure maximum tire life and
tread wear.
2. Use Poleyrex EM (Exxon Mobil) or equalivant lubricant.
Clean grease fitting, apply grease gun to fitting (1/2 shot).
Remember too much grease or injecting grease too quickly
can cause premature bearing failure. Slowly apply the
recommended amount of grease, taking a miniute or so to
apply.
Eyesight Hazard
WARNING
ALWAYS wear safety glasses when
removing or installing force fitted
parts. Failure to comply may result in
serious injury.
Table 9 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
Figure 33. Grease Fittings Electric Motor
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical compo-
nents of the trailer. When specifying or replacing the trailer
wheels it is important the wheels, tires, and axle are prop-
erly matched.
DamagedWheels
WARNING
DO NOT attempt to repair or modify a
wheel. DO NOT install an inter-tube to
correct a leak through the rim. If the
rim is cracked, the air pressure in the
inter-tube may cause pieces of the rim to explode (break-
off) with great force and can cause serious eye or bodily
injury.
PAGE 30 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)
3. Afterfirstroaduse,retorquealllugnutsinsequence.Check
all wheel lug nuts periodically.
Lug NutTorque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque. Be sure to use only the fasteners matched
to the cone angle of the wheel. Proper procedure for attach-
ment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 34. DO NOT
torquethewheellugnutsallthewaydown.Tighteneachlug
nut in 3 separate passes as defined byTable 10.
Table 10. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
13"
14"
15"
16"
20-25
20-25
20-25
20-25
20-25
35-40
35-40
50-60
50-60
50-60
50-65
50-65
90-120
90-120
90-120
NEVER! use an pneumatic air gun
to tighten wheel lug nuts.
NOTE
Figure 34. Wheel Lug Nuts Tightening Sequence
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)
Suspension
Keep Hands
Clear of Drum!
WARNING
The rigid type axle and associated hardware (Figure 35)
should be periodically inspected for signs of excessive wear,
elongation of bolt holes, and loosening of fasteners. Re-
place all damaged parts immediately.
When rotating the mixing drum from the dump position to the
upright position, keep hands clear of safety grate. The
possibility exists of hands or fingers being crushed (Figure 37).
Figure 35. Axle Support Components
Mixer Cleaning
1. ALWAYS disconnect the spark plug wire (gasoline
engines) before cleaning the inside of the drum. If mixer is
equipped with an electric motor remove power cord from
AC power receptacle. In addition make sure the clutch
engagement lever is dis-engaged.
Figure 37. Safety Grate (Crush Hazard)
7. When cleaning of the entire mixer is done, return mixing
drum to an upright position.
2. Make sure the rear section of the safety grate is connected
to the mixing drum.
3. At the end of each day’s operation, place mixer drum in an
upright position and spray inside of tub immediately with
water to prevent lumps of dried mortar or plaster from
forming and contamination of future batches, DO NOT allow
a buildup of materials to form on the blades or anywhere
inside the drum.
Mixer Storage
For storage of the mixer for over 30 days, the following is
recommended:
Drain the fuel tank completely, or add STA-BIL to the
fuel.
4. Rotate mixer to dump position and remove debris.
Run the engine until the fuel is completely consumed.
5. Thoroughly clean the entire mixer, wheels, cabinet and
frame.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
6. NEVER! pour or spray water over the engine or electric
motor (Figure 36).
Clean the entire mixer and engine compartment.
Place the mixing drum in the down position (mouth facing
downward).
Cover the mixer and place it a clean dry area, that is
protected from harsh elements.
Figure 36. No Spraying of Water
PAGE 32 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER —TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine, Mixer and Electric Motor
Troubleshooting (Tables 11, 12 and 13) information shown
below and on the proceeding pages.
If the problem cannot be remedied, please leave the unit
just as it is and consult or company's service department.
TABLE 11. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Fuel filter clogged?
Stuck carburetor?
Spark plug is red?
Flush or replace fuel tank.
Replace fuel filter
Check float mechanism.
Poor starting
Spark plug is fouled. Check tranistor ignition unit.
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
Spark plug is blue-white?
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Start/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Oil pressure alarm lamp blinks
upon starting?
Check Automatic shutdown circuit "oil sensor".
Replace cylinder and piston and if necessary axel joint.
Tighten cylinder head connecting bolts.
Engine will not turn over?
Cylinder head connecting bolts
loose?
Cylinder head gasket damaged? Replace cylinder head gasket.
Insufficient power output "no
compression"
Malfunction of valve seat?
Spark plug is loose?
Worn piston rings?
Re-seat valves.
Replace spark plug.
Replace piston rings.
Malfunction in air-cleaner
system, air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Insufficient power output
"compression"
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
Malfunction in fuel system?
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 PLASTER/MORTAR MIXER —TROUBLESHOOTING (ENGINE)
TABLE 11. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Malfunction in cooling fan?
Air in-take filter clogged?
SOLUTION
Check or replace cooling fan.
Insufficient power output
"compression" and overheats
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Burns to much fuel
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Replace lubricating oil with correct viscosity.
Lubricating oil is wrong
viscosity?
Exhaust color is continiously
"WHITE"
Worn rings?
Replace rings
Air cleanner clogged?
Clean or replace air cleaner.
Adjust choke valve to the correct position.
Choke valve has not been set
to the correct position?
Exhaust color is continiously
"BLACK"
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Adjust carburetor.
Poor carburetor adjustment
"engine runs too rich?
PAGE 34 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 —TROUBLESHOOTING (MIXER/ELECTRIC MOTOR)
TABLE 12. MIXER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
Worn or defective V-belt?
SOLUTION
Replace V-belt.
Blades will not rotate.
Adjustment lever mis-aligned?
Check position of adjustment lever. Adjust if necessary.
Replace seals.
Material leaking from drum
ends.
Worn or defective paddle shaft
seals?
Defective or worn drum support
brackets?
Apply grease to bracket or replace.
Drum difficult to discharge (tilt)
Blades adjusted too tight.
Adjust blades until they almost touch side walls of drum.
TABLE 13. ELECTRIC MOTOR TROUBLESHOOTING
POSSIBLE PROBLEM
SYMPTOM
SOLUTION
No voltage to motor?
Check power source.
Replace extension cord.
Replace switch.
Defective extension cord?
Blades will not rotate.
Defective motor ON/OFF switch?
Defective motor windings?
Repair windings or replace windings.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER —WIRING DIAGRAM (ELECTRIC MOTOR)
Figure 24. Electric MotorWiring Diagram
PAGE 36 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
2%
2% 12347
12348
12349
3
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
4
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 38 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — SUGGESTED SPARE PARTS
MS-63P/S PLASTER AND MORTAR MIXER 1TO 3
UNITSWITH HONDA GX160K1QMX2HX2 AND
GX240K1HA2 ENGINES
Part numbers on this
Suggested Spare Parts List
may supercede/replace the P/
N's shown in the test pages of
this manual.
NOTE
Qty.... P/N ...................... Description
6 ....... 491107 ................ V-BELT A32, HONDA ENGINE (5.5 HP)
6 ....... 505834 ................ V-BELT A36, HONDA ENGINE (8.0 HP)
6 ....... 491112 ................ V-BELT A40, ELECTRIC MOTOR
2 ....... EM914288 ........... OIL SEAL, AXLE
4 ....... EM903113 ........... BEARING, CONE, AXLE
4 ....... EM903112 ........... BEARING, CUP, AXLE
2 ....... 20654-001 ........... SEAL, PADDLE SHAFT (BLACK)
2 ....... 530029 ................ RING, RETENTION
2 ....... 20104-002 ........... SEAL, SHAFT URETHANE (YELLOW)
3 ....... 17210ZE1517 ...... ELEMENT, AIR CLEANER (5.5 HP)
3 ....... 17210ZE2515 ...... ELEMENT, AIR CLEANER (8.0 HP)
3 ....... 9807956846......... SPARK PLUG, BPR6ES, NGK
3 ....... 9807956855......... SPARK PLUG, W20EPR-U, DENSO
1 ....... 28462ZH8003...... ROPE, RECOIL STARTER (5.5 HP)
1 ....... 28462ZE2W11..... ROPE, RECOIL STARTER (8.0 HP)
1 ....... 17620ZH7023...... CAP, FUEL TANK
2 ....... 25647-502 ........... KIT, WIPER BLADES (STEEL DRUM)
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 40 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO
1
2
3
4
5
6
7
8
PART NO
DCL151
EM948630
CIPDCL160
510164
504713
35137
512527
513523
PART NAME
DECAL,TOWING INSTRUCTIONS
DECAL, PUSH TO STOP
QTY.
REMARKS
2
1
2
3
1
1
3
1
1
1
1
1
1
DECAL, CRUSHWARNING
DECAL, STOW LOGO (SMALL)
DECAL, SAFETY INSTRUCTIONS
DECAL, WARNING READ
DECAL, STOW LOGO (LARGE)
DECAL, BELT SLIP
DECAL, WARNING SAFETY GRATE
DECAL, CRUSH WARNING SAFETY GRATE
DECAL, WARNING DUMP HANDLE
DECAL, DRUM LOCK
9
513479
10
11
12
13
14
DCL335
DCL280
513522
13118
DECAL, POWDER COATED
NAMEPLATE........................................................ 1 ......... CONTACT PARTS DEPT.
SEE OPERATION AND SAFETY DECALS PAGE.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — FRAME ASSY.
FRAME ASSY.
PAGE 42 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — FRAME ASSY.
FRAME ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
514842
491692
530023
507444
514834
530013
20278-001
EM963692
492584
514802Y
10176
LOCK, PIN
1
1
1
1
1
1
1
6
6
1
1
1
1
COTTER PIN
SPRING LOCKING PIN
WASHER, FLAT 3/4"
MAIN FRAME
CLUTCH HANDLE LEVER
CLUTCH HANDLE GRIP
BOLT 1/2" UNC 1-1/2"
NUT, LOCK 1/2"
AXLE, UNIVERSAL
LOCK NUT 1/2" NC
BOLT 1/2"-13 X 4 G5
SAFETY CHAIN
CONNECTOR LINK ..................................................... 2 ...................BEFORE JANUARY 2006
CONNECTOR LINK ..................................................... 1 ...................AFTER JANUARY 2006
CLEVIS SAFETY HOOK ............................................ 1 ...................AFTER JANUARY 2006
CHAIN AND LINK KIT................................................. 1 ...................INCLUDES ITEMS W/
BALL HITCH 2-INCH ................................................... 1 ...................CONTACT UNIT SALES
9
10
11
12
EM124
13
*
14
*
01004
01004
516580
13363KIT
HBC-1
HLC-1
14
*
14A
*
15
16
17
18
*
LOOP HITCH .............................................................. 1 ...................CONTACT UNIT SALES
PIN HITCH 1-INCH...................................................... 1 ...................CONTACT UNIT SALES
HPC-1
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — PADDLE SHAFT ASSY.
PADDLE SHAFT ASSY.
PAGE 44 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — PADDLE SHAFT ASSY.
PADDLE SHAFT ASSY.
NO.
1
2
PART NO.
514752
492584
PART NAME
QTY.
1
6
REMARKS
PADDLE SHAFT
NUT, LOCK 1/2"
3
4
5
6
530140C
492400
EM200292
530141
PADDLE ARM, CENTER ENGINE END
BOLT, 1/2 " X 3-1/2" G5
INSERT, PADDLE ARM
PADDLE ARM, ENGINE END
WASHER, FLAT 1/2"
1
2
4
1
7
504322
6
8
9
10
11
12
EM200297
530143
505196
U-BOLT, END PADDLES
PADDLE ARM, CENTER TOW END
SCREW, 3/8" NC X 1-1/2 " G5
WASHER, FLAT 3/8"
BLADE, SIDE, RUBBER
BLADE, SIDE, SCRAPPER
NUT, HEX 3/8" NC G5
2
1
18
28
4
492598
25667-001
25668-001
492554
*
13
4
14
15
16
17
18
19
14
14
1
2
2
492624
WASHER, LOCK 3/8"
530142C
33074-001
33017-001
25647-502
PADDLE ARM, TOW END
BLADE ,SCRAPPER END
BLADE, RUBBER END
*
KIT, WIPERS............................................................... 1 ...................INCLUDES ITEMS W/
*
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — STEEL DRUM ASSY.
STEEL DRUM ASSY.
24
23
22
20
20
20
26
29
21
25
20
28
27
14
30
15
31
4
15
12
11
17
5
9
1
4
13
13
6
3
10
1
9
16
6
5
11
7
8
3
6
8
7
10
12
1
2
19
18
18
PART OF
REAR FRAME
PART OF
FRONT FRAME
NOTES:
SET SCREWS AND BEARING
COLLAR ARE INCLUDED WITH
BEARING AND CANNOT BE
PURCHASED SEPARATELY.
1
PAGE 46 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — STEEL DRUM ASSY.
STEEL DRUM ASSY.
NO.
1
2
PART NO.
530028Y
3249Y
PART NAME
DRUM BEARING BRACKET
CAP, DUST
QTY.
2
1
REMARKS
3
20561-001
BEARING SEALED ........................................... 2 ........... SET SCREWS AND BEARING
.......................................................................................... COLLAR CANNOT BE PURCHASED
.......................................................................................... SEPARATELY.
4
5
6
7
8
9
491008
CAP, GREASE FITTING
FITTING, GREASE
NUT, LOCK 3/8"
WASHER, FLAT 3/8"
TRUNNION HUB
ROLL PIN 3/16" X 3/4"
SEAL, SHAFT (BLACK)
RING, RETENTION
SEAL, SHAFT URETHANE (YELLOW)
BOLT 3/8" NC X 1/4" G5
DRUM, STEEL
SET SCREW
MAIN GEAR
KEY, 3/8" X 50 MM
CARRIAGE BOLT 3/8-16 X 1-1/2"
SHAFT, PADDLE
WASHER, FLAT 1/2"
LIFT BAR
PIN, COTTER
GRATE
PIN, COTTER
HEX NUT 1/2" G5
WASHER, LOCK 1/2"
BOLT 1/2" NC 1-1/4" G5
CAPSCREW, HHCS 1/2" NC X 1-1/4"
NUT, LOCK1/2" NC
HANDLE DUMP
2
2
12
4
2
2
2
2
2
8
1
2
1
1
4
1
4
1
1
1
2
2
2
2
1
1
1
1
EM916019
EM969013
3019092
514778Y
513453
20654-001
530029
20104-002
513452
515009
492484
530043
500432
17985-012
514752
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
492600
515032
EM925191
514962Y
505070
492556
6109180
EM963692
492393
492584
EM201537Y
15081
GRIP, DUMP HANDLE
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.
DRUM AND PADDLE SHAFT COMPLETE ASSY.
PAGE 48 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.
DRUM AND PADDLE SHAFT COMPLETE ASSY.
NO.
1
PART NO.
516069
PART NAME
QTY.
REMARKS
DRUM AND SHAFT COMPLETE ASSY. ........... 1 ........... INCLUDES ITEMS LISTED BELOW:
530028Y
3249Y
20561-001
491008
EM916019
EM969013
3019092
514778Y
513453
20654-001
530029
DRUM BEARING BRACKET
CAP, DUST
BEARING SEALED
CAP, GREASE FITTING
FITTING, GREASE
NUT, LOCK 3/8"
WASHER, FLAT 3/8"
TRUNNION HUB
ROLL PIN 3/16" X 3/4"
SEAL, SHAFT (BLACK)
RING, RETENTION
2
1
2
2
2
12
4
2
2
2
2
20104-002
513452
515009
SEAL, SHAFT URETHANE (YELLOW)
BOLT 3/8" NC X 1/4" G5
DRUM, STEEL
2
8
1
492484
530043
SET SCREW
MAIN GEAR
2
1
500432
EM963057
514752
KEY, 3/8" X 50 MM
CAPSCREW HHCS 3/8 X 1-1/2"
SHAFT, PADDLE
1
4
1
492600
514946
WASHER, FLAT 1/2"
GRATE
2
1
505070
492556
PIN, COTTER
HEX NUT 1/2" G5
2
2
6109180
EM963692
EM201537
15081
WASHER, LOCK 1/2"
BOLT 1/2" UNC 1-1/2"
HANDLE DUMP
GRIP, DUMP HANDLE
PADDLE SHAFT
2
2
1
1
514752
1
492584
530142
510721
NUT, LOCK 1/2"
PADDLE ARM, CENTER ENGINE END
BOLT, 1/2 " X 6" G5
6
1
2
EM200292
530141
504322
EM200297
530143
505196
EM923023
25667-001
25668-001
2105164
EM923343
530140
INSERT, PADDLE ARM
PADDLE ARM, ENGINE END
WASHER, FLAT 1/2"
U-BOLT, END PADDLES
PADDLE ARM, CENTER TOW END
SCREW, 3/8" NC X 1-1/2 " G5
WASHER, FLAT 5/16"
BLADE, SIDE, RUBBER
BLADE, SIDE, SCRAPPER
NUT, HEX 5/16" NC G5
WASHER, LOCK 5/15"
PADDLE ARM, TOW END
BLADE ,SCRAPPER END
BLADE, RUBBER END
4
1
6
2
1
18
28
4
4
14
14
1
2
2
33074-001
33017-001
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — AXLE ASSY.
AXLE ASSY.
PAGE 50 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — AXLE ASSY.
AXLE ASSY.
NO
PART NO
PART NAME
DUST CAP
LUG NUTS
QTY.
2
8
REMARK
1
2
3
3
4
5
6
7
8
9
#
3469
#
8115
3005
516476
8164
TIRE AND RIM, CARLISE .............................................. 2 ........... BEFORE JANUARY 2006
TIRE AND RIM, TOWMASTER II ................................... 2 ........... AFTER JANUARY 2006
CASTLE NUT 1"
COTTER PIN 1/8" X 1-1/2'
WASHER, FLAT, .087" THICKNESS
WASHER, FLAT, .135" THICKNESS
BEARING CONE
2
2
2
1
4
4
2
491688
EM511159
EM501299
EM903113
EM903012
EM914288
EM941306
514802Y
#
#
BEARING CUP
OIL SEAL
10
11
12
#
HUB ASSY., 4-BOLT ....................................................... 2 ........... INCLUDES ITEMS W/
AXLE, UNIVERSAL
#
1
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — ENGINE ASSY.
ENGINE ASSY.
PAGE 52 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — ENGINE ASSY.
ENGINE ASSY.
NO
1
2
3
4
5
6
7
8
PART NO
492583
506488
EM905016
492378
490957
513868
500214
502226
492077
505084
492467
491107
07055-034
503117
508344
492367
492378
PART NAME
QTY.
REMARKS
NUT 3/8" NC G5
4
8
2
4
1
1
1
1
1
1
4
FLAT WASHER 3/8
PILLOW BLOCK BEARING
BOLT 3/8" NC X 1-3/4" G5
RING, RETAINER
PINION GEAR
KEY, 1/4" X 30 MM
PINION SHAFT
PULLEY (LARGE)
KEY, 1/4" X 55 MM
SET SCREW, 5/16' NC 3/8"
V-BELT, A-32 ....................................... 2........... HONDA 5.5 HP
V-BELT, A-34 ....................................... 2........... HONDA 8.0 HP
BOLT, 3/8" NC X 3" G5
WASHER, FLAT 5/16"
BOLT 5/16" NC X 1-3/4" G5 ................ 4........... HONDA 5.5 HP
BOLT 3/8" NC X 1-3/4" G5 .................. 4........... HONDA 8.0 HP
9
10
11
12
12
13
14
15
15
16
16
17
18
18
19
20
21
22
22
23
23
24
24
25
26
26
1
1
GX160K1QMX2HX2 ENGINE, HONDA ................................ 1........... HONDA 5.5 HP
GX240K1HA2
514985
492055
505205
604445
530454
530019
492597
492598
492623
492624
492553
492554
EM102014
501019
ENGINE, HONDA ................................ 1........... HONDA 8.0 HP
BELT RETAINER BAR
PULLEY, (SMALL) .............................. 1........... HONDA 5.5 HP
PULLEY, (SMALL) .............................. 1........... HONDA 8.0 HP
RING, RETENTION
SHAFT, ENGINE MOUNT
ENGINE MOUNTING PLATE
WASHER, FLAT 5/16"
WASHER, FLAT 3/8"
WASHER, LOCK 5/16"
WASHER, LOCK 3/8"
NUT, HEX 5/16"
1
2
1
1
6
6
4
4
4
4
1
NUT, HEX 3/8"
SPRING, EXTENSION
SQ. KEY 3/16" X 45 MM..................... 1........... HONDA 5.5 HP
SQ. KEY 6.3 X 6.3 X 43 MM .............. 1........... HONDA 8.0 HP
90745ZE2600
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — ELECTRIC MOTOR ASSY.
ELECTRIC MOTOR ASSY.
PAGE 54 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — ELECTRIC MOTOR ASSY.
ELECTRIC MOTOR ASSY.
NO
1
2
3
4
8
9
PART NO
492583
506488
EM905016
492378
20216-001
20061-001
500275
492467
491112
503117
492598
492582
35L229S302
514985
502213
604445
530454
530089
2105164
492623
EM923023
492378
PART NAME
NUT 3/8" NC G5
FLAT WASHER 3/8
PILLOW BLOCK BEARING
BOLT 3/8" NC X 1-3/4" G5
PINION SHAFT
PULLEY (LARGE)
KEY, 1/4" X 40 MM
QTY.
4
8
2
4
1
1
1
3
2
1
2
1
1
1
1
2
1
1
4
4
8
4
1
1
REMARKS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
SET SCREW, 5/16' NC 3/8"
V-BELT, A-40
CAP SCREW 5/16"-18X 1"
WASHER, FLAT 3/8"
NUT, NYLON 5/16"-18
ELECTRIC MOTOR 1.5 HP
BELT RETAINER BAR
PULLEY, (SMALL)
RING, RETENTION
SHAFT, ENGINE MOUNT
ELECTRIC MOTOR MOUNTING PLATE
NUT, HEX 5/16" NC
WASHER, LOCK 5/16"
WASHER, FLAT 5/16"
BOLT 3/8" NC X 1-3/4" G5
SPRING, EXTENSION
KEY, 3/16" X 50 MM
530024
500169
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — CABINET ASSY.
CABINET ASSY.
PAGE 56 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOW MS-63 MIXER — CABINET ASSY.
CABINET ASSY.
NO
1
2
3
4
PART NO
515014
490202
13287
2203
PART NAME
QTY.
REMARKS
CABINET, ENGINE W/DECALS .................. 1 ........... INCLUDES ITEMS W/
*
RUBBER PROTECTOR
4
LOCK NUT 8-32........................................... 6 ........... REPLACEMENT PART ONLY
WASHER, FLAT #10 .................................... 6 ........... REPLACEMENT PART ONLY
SCREW RHMS 8-32 X 1/2" ......................... 6 ........... REPLACEMENT PART ONLY
5
1307
6
*
7
8
491010
492375
492598
LATCH ASSY., COMPLETE
BOLT 3/8" NC X 1" G5
WASHER, FLAT 3/8"
2
4
4
9
492583
NUT 3/8" NC G5
KNOB, MUSHROOM
SWITCH, PUSH-PULL
WIRE HARNESS
PAINT, SPRAY CAN 12 OZ., YELLOW
PAINT, GALLON CAN, YELLOW
4
1
1
1
AR
AR
10
11
12
13
14
29174-001
29173-001
504135C
RAL1003S
RAL1003G
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 58 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO
1
PART NO
PART NAME
GASKET ELBOW
QTY.
1
REMARKS
16271ZE1000
17210ZE1505
17218ZE1821
17230ZE1820
17232891000
17238ZE7010
17239ZE1000
17410ZE1020
90201415000
90325044000
90325044000
957010602000
2
AIR CLEANER ELEMENT DUAL ................. 1 .......... INCLUDES ITEMS W/#
3#
4
FILTER OUTER
1
1
1
1
1
COVER AIR CLEANER DUAL
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
5#
6
*
7
*
8
ELBOW COMP. AIR CLEANER .................... 1 .......... INCLUDES ITEMS W/
NUT CAP 6MM
NUT WING TOOL BOX SETTING
NUT WING TOOL BOX SETTING
BOLT FLANGE 6 x 20
*
9
2
1
1
1
11
12
13
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 60 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF1000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. .......................................... 1 .......... INCLUDES ITEMS W/
*
2
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
2
2
2
2
1
1
1
2
1
1
1
1
2
2
3
4
5
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
VALVE, EX.
SPRING, VALVE
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT
NUT, PIVOT ADJUSTING
6
*
7
8
9
10
11
12
13
14
15
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 62 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8W51
16124ZE0005
16166ZH8W50
16955283000
162111ZE1000
16212ZH8800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1406
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
CHAMBER SET, FLOAT............................... 1 .......... INCLUDES ITEMS W/%
SCREW SET
SCREW SET DRAIN
SCREW SET B
CHOKE SET
CARBURETOR ASSY (BE65B) ................... 1 .......... INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
1
1
1
*
2
*
3
*
4
*
5
1
1
1
1
*
6 %
*
7
*
8
*
9
*
10
1
1
1
1
1
1
1
*
11
*
12
GASKET, FULL STRAINER CUP
INSULATOR CARBURETOR
GASKET, INSULATOR
*
13
14
15
16
17
18
SPACER COMP. CARBURETOR
GASKET CARBURETOR
LEVER COMP., CHOKE (STD) .................... 1 .......... INCLUDES ITEMS W/#
LEVER VALVE
1
1
1
1
1
2
1
1
1
1
1
*
19
PLATE LEVER SETTING
SPRING, PETCOCK LEVER
GASKET, PETCOCK
CUP, FUEL STRAINER
SCREW, PAN 3X6
PIN, SPRING 2X12
JET, MAIN #65
*
20
*
21
*
22
*
23
*
24#
25
99101ZH70650
99101ZH70680
99101ZH70700
99204ZE00350
*
JET, MAIN #68
JET, MAIN #70
26
JET SET, PILOT #35
*
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 64 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO
2
PART NO
PART NAME
QTY.
REMARKS
16500ZH8821
16551ZE0010
16555ZE1000
16561ZE1020
16562ZE1020
16571ZH8000
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH8811
16584883300
16592ZE1810
90013883000
90015ZE5010
90114SA0000
93500050250H
938930501600
9405006000
CONTROL ASSY., REMOTE .......................... 1 .......... INCLUDES ITEMS W/
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING, THROTTLE RETURN
LEVER, CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
*
4
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
5
6
7
8
*
9
*
10
*
11
12
13
14
15
17
18
19
22
23
24
*
*
*
*
*
SPACER, CONTROL LEVER
BASE COMP., CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE (6X12)
BOLT, GOVERNOR ARM
NUT, SELF- LOCK (6MM)
SCREW, PAN (5X25)
*
*
*
SCREW WASHER (5X16)
NUT, FLANGE, 6MM
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 66 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
11300ZE1633
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
15625ZE1003
91202883005
9430108140
957010803200
961006205010
COVER ASSY, CRANKCASE (W TYPE) ......... 1 ..........INCLUDES ITEMS W/
*
3
GASKET CASE COVER
1
4
5
CAP ASSY, OIL FILLER................................... 1 ..........INCLUDES ITEMS W/#
CAP ASSY, OIL FILLER................................... 1 ..........INCLUDES ITEMS W/%
9#
10%
11
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
OIL SEAL, 25X41X6
1
1
1
2
6
1
*
12
PIN A, DOWEL 8X14
13
BOLT, FLANGE 8X32
14
BEARING, RADIAL BALL, 6205
*
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 68 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
5
PART NO.
13310ZE1621
PART NAME
CRANKSHAFT (H- TYPE)
QTY.
1
REMARKS
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 70 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
06165ZE1000
12000ZH8811
15510ZE1023
16510ZE1000
16511ZE1000
16513ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91202883005
91353671003
9405010000
9410106800
9425108000
957010601200
GOVERNOR KIT ........................................................ 1 .......... INCLUDES ITEMS W/
*
2
CYLINDER ASSY. BARREL OIL ALERT .................... 1 .......... INCLUDES ITEMS W%
SWITCH ASSY. OIL LEVEL
GOVERNOR ASSY. .................................................... 1 .......... INCLUDES ITEMS/W#
3
1
4
*
5 #
WEIGHT, GOVERNOR
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
2
2
1
1
2
1
2
1
1
1
1
1
2
1
2
*
7 #
*
8
9
*
10
11
WASHER, THRUST 6MM
WASHER, DRAIN PLUG 10.2MM
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL(6205)
OIL SEAL 25x41x6
*
*
12
13
14%
15%
16
O-RING 14MM ARAI
17
NUT, FLANGE 10MM
18
WASHER, PLAIN, 6MM
PIN, LOCK, 8MM
*
19
20
BOLT, FLANGE 6 x 12
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
HONDA ENGINE — CYLINDER HEAD
PAGE 72 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
12210ZH8000
12204ZE1306
12205ZE1315
12216ZE5300
12251ZF1800
12310ZE1010
12391ZE1000
15721ZH8000
90016ZE1000
90043ZE1020
90047ZE1000
9430110160
957230806000
9807956846
CYLINDER HEAD, COMP .............................. 1 ........... INCLUDES ITEMS W/
*
2
GUIDE, IN. VALVE (OVER SIZE)
GUIDE, EX. VALVE (OS)
CLIP, VALVE GUIDE
1
1
1
1
1
1
1
4
2
2
2
4
1
*
3
*
4
5
GASKET, CYLINDER HEAD
COVER COMP, HEAD
6
7
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
8
9
BOLT, FLANGE 6X13
10
11
12
14
15
BOLT, STUD 6X109
BOLT, STUD 8X32
PIN A, DOWEL 10X16
BOLT, FLANGE 8X60
PLUG, SPARK (BPR6ES NGK)
9807956855
PLUG, SPARK (W20EPR-U ND)
1
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 74 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO
2
PART NO
PART NAME
QTY.
1
REMARKS
19610ZE1000ZC
19612ZH8810
90601ZH7013
19630ZH8000
32197ZH8003
36100ZE1015
90022888010
COVER COMP., FAN NH1(BLACK)
PLATE, SIDE (STD)
CLIP, HARNESS
SHROUD COMP.
SUB-HARNESS
SWITCH ASSY., ENGINE
BOLT, FLANGE 6X20
4
1
7
8
10
11
14
1
1
1
1
1
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 76 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
13331357000
19511ZE1000
28451ZH8003
31100ZE1000
KEY, SPECIAL WOOD RUFF, 25X18
1
1
1
1
2
FAN, COOLING
4
5
PULLEY STARTER
FLYWHEEL COMP.
8
90201878003
NUT, SPECIAL, 14MM
1
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 78 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO
1
PART NO
PART NAME
MUFFLER COMP.
QTY.
1
REMARKS
18310ZH8810
18320ZF1H01
18355ZE1000
18381ZH8800
90050ZE1000
90055ZE1000
94001080000S
3
PROTECTOR, MUFFLER
ARRESTER, SPARK
GASKET, MUFFLER
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
NUT, HEX (8MM)
1
7
8
11
12
15
1
1
4
1
2
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 80 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE1020ZF
17620ZH7013
17631ZH7003
91353671003
9405006000
950014500840M
9500202080
957010602500
RUBBER, SUPPORTER
1
1
1
2
JOINT, FUEL TANK
3
5
TANK COMP., FUEL NH1 (BLACK)
CAP COMP., FUEL FILLER ............................. 1 .......... INCLUDES ITEMS W/#
6#
11
12
13
14
15
GASKET, FUEL FILLER CAP
O-RING (14MM) ARAI
1
1
2
1
2
1
NUT, FLANGE (6MM)
BULK HOSE, FUEL (4.5X8000) (4.5X140)
CLIP, TUBE (B8)
BOLT, FLANGE (6X25)
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 82 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
30500ZE1033
30700ZE1013
36101ZE1010
90121952000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
WIRE, STOP SWITCH (370MM)
BOLT, FLANGE, 6X25
1
1
1
2
2
7
11
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 84 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
13010ZF1023
13011ZF1023
13012ZF1023
13013ZF1023
13101ZH8000
13102ZH8000
13103ZH8000
13104ZH8000
13111ZE1000
132A0ZE1000
90001ZE1000
RING SET, PISTON (STD)
RING SET, PISTON (0.25)
RING SET, PISTON (0.50)
RING SET, PISTON (0.75)
PISTON (STD)
1
1
1
2
1
PISTON (0.25)
1
PISTON (0.50)
1
PISTON (0.75)
1
3
4
5
*
6
PIN, PISTON
1
ROD ASSY, CONNECTING ............................ 1 .......... INCLUDES ITEMS W/
*
BOLT, CONNECTING ROD
CLIP, PISTON PIN, 18MM
2
2
90551ZE1000
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 86 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
28400ZH8013ZB
28410ZH8003ZB
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
957010600800
STARTER ASSY, RECOIL NH1(BLACK) ........ 1 .......... INCLUDES ITEMS W/
*
2
CASE COMP., RECOIL STARTER
REEL, RECOIL STARTER
RATCHET, STARTER
GUIDE, RATCHET
1
1
2
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
*
7
*
8
*
9
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
*
10
11
12
*
*
BOLT, FLANGE 6X8
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
PAGE 88 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
21521883741
21591ZH8740
21621883741
21692ZH8800
23710883740
90002883740
90131883000
91202883005
9410912000
CASE, REDUCTION
1
1
1
1
1
1
1
1
1
1
1
1
1
GASKET, REDUCTION CASE
COVER, REDUCTION
GASKET, REDUCTION COVER
SHAFT, P.T.O.
BOLT, BREATHING
BOLT, DRAIN PLUG
OIL SEAL, 25 x 41 x 6
WASHER, DRAIN PLUG
BOLT, FLANGE 8 x 32
BOLT, FLANGE 8 x 35
BEARING, RADIAL BALL 6204
BEARING, RADIAL BALL 6305
9
10
11
12
13
957010803208
957010803500
961006204000
961006305000
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — LABEL ASSY.
LABEL ASSY.
PAGE 90 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QMX2HX2 ENGINE — LABEL ASSY.
LABEL ASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
87521ZH8010
87522ZE1810
87522ZH9000
87258ZE1810
87530ZH8810
87532ZB4G60
87532ZB4H50
87532ZH8810
EMBLEM, INTERNAL
MARK, CAUTION EXTERNAL
LABEL, CAUTION
2
1
3
1
6
MARK, CHOKE
1
7
LABEL, SPECIFICATION EXTERNAL
MARK, OIL ALERT G
MARK, OIL ALERT F
MARK, OIL ALERT E
1
8
1
1
1
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 92 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
*
5
PART NO.
PART NAME
QTY.
REMARKS
16271ZE2000
17210ZE2515
17218ZE2505
17231ZH9820
17232891000
17238ZE2310
17239ZE1000
17410ZE2020
0037806000
90325044000
90009ZE2003
9405006000
GASKET, ELBOW ..................................... 1 ............. INCLUDES ITEM W/
*
ELEMENT, AIR CLEANER, DUAL
FILTER, OUTER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW COMP., AIR CLEANER ............... 1 ............. INCLUDES ITEM W/
WINGNUT 6MM
WINGNUT, TOOL BOX SETTING
BOLT- WASHER 6 X 22
NUT, FLANGE 6MM
1
1
1
1
2
1
6
8
9
#
#
10
12
13
14
15
#
1
2
1
2
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 94 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
1
2
3
4
5
6
*
7
8
PART NO.
PART NAME
QTY.
REMARKS
14100ZE2W01
14100ZE2306
14410ZE2013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE2000
14721ZE2000
14751ZE2003
14771ZE2000
14773ZE2000
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEM W/
*
CAMSHAFT
ROD PUSH
ARM VALVE ROCKER
LIFTER VALVE
PIVOT ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
1
2
2
2
2
1
1
1
2
1
1
1
1
2
2
VALVE, EX.
SPRING, VALVE
9
10
11
12
13
14
15
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
NUT, PIVOT ADJ.
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 96 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1 +
16010ZE2812
16011ZA0931
16013ZA0931
16016ZHW01
16024ZE1811
16028ZE0005
16028ZE2005
16100ZE2W71
16124ZE0005
16166ZE2W70
16075GHBB00
16075GHBB00
16211ZE2000
16220ZA0702
16221ZA0800
16223ZA0800
16610ZE1000
16953ZE1812
16954ZE1811
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
1
1
1
1
*
2
3
*
*
5
6 +
SCREW SET
*
SCREW SET, DRAIN
SCREW SET B
CHOKE SET
CARBURETOR ASSY.................... 1 ..... INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
*
7 +
*
8
*
9
10
*
*
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
*
11
*
12
*
COLLAR, SET
O-RING
13
*
14
INSULATOR, CARB.
SPACER COMP., CARB.
GASKET, CARBURETOR
GASKET, INSULATOR
LEVER COMP., CHOKE, STD.
LEVER, VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3 X 6
PIN, SPRING 2 X 12
JET, MAIN #82, OPTIONAL
JET, MAIN #85, OPTIONAL
JET, MAIN #88
15
16
17
18
19
*
20
*
21
*
22
*
23
*
24
*
25
26
99101ZH70820
99101ZH70850
99101ZH80880
99204ZE20400
16015ZE8005
*
26
*
26
*
27
28
JET SET, PILOT #40
CHAMBER SET, FLOAT ................ 1 ..... INCLUDES ITEMS W/+
*
*
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 98 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
2
3
4
5
PART NO.
PART NAME
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
CONTROL ASSEMBLY ................................ 1 .......... INCLUDES ITEMS W/
QTY.
REMARKS
16551ZE2000
16555ZE2000
16561ZE2000
16571ZE2000
16570ZE2W00
16571ZE2W00
16574ZE1000
16575ZE2W00
16578ZE1000
16581ZE2W00
16584883300
90013883000
90015ZE5010
90114SA0000
93500050280A
9405006000
1
1
1
1
8
*
10
LEVER, CONTROL
SPRING, LEVER
1
1
1
1
1
1
2
1
1
1
1
*
11
*
12
*
WASHER, CONTROL LEVER
SPACER, CONTROL LEVER
BASE, CONTROL
SPRING, CONTROL ADJUSTING
BOLT, FLANGE (6 X 12) (CT200)
BOLT, GOVERNOR ARM
NUT, SELF- LOCK (6MM)
SCREW, PAN (5 X 28)
NUT, FLANGE
14
*
15
*
16
*
19
20
21
*
24
*
27
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 100 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
2
PART NO.
11400ZE2621
PART NAME
QTY.
REMARKS
COVER ASSY., CRANKCASE ..................... 1........... INCLUDES ITEMS W/
(H-TYPE) (BALANCER)
*
3
4
5
8
9
11381ZE2801
15600ZG4003
15600735003
15625ZE1003
15625ZE1003
16510ZE2811
GASKET, CASE COVER
1
CAP ASSY., OIL FILLER ............................. 1........... INCLUDES ITEMS W/
CAP ASSY., OIL FILLER ............................. 1........... INCLUDES ITEMS W/
#
%
%
#
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
1
1
10
GOVERNOR ASSEMBLY (BALANCER) ...... 1........... INCLUDES ITEMS W/+
11 + 16511ZE2000
WEIGHT, GOVERNOR
2
1
2
1
1
1
2
1
7
1
1
1
1
*
12 + 16512ZE2811
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
WASHER (6 X 16)
CLIP, GOVERNOR HOLDER
PIN, DOWEL (8 X 12)
WASHER, PLAIN (6MM)
BOLT, FLANGE (8 X 35)
BEARING, RADIAL BALL (6202)
BEARING, RADIAL BALL (6204)
BEARING, RADIAL BALL (6206)
BEARING, RADIAL BALL (6302)
*
13 + 16513ZE2000
*
14
15
16
17
18
19
20
21
22
23
16531ZE2000
90473147000
90602ZE1000
90701HC4000
58176
957010803500
961006202000
961006204000
961006206000
961006302000
*
*
*
*
*
*
*
*
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 102 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
3
8
PART NO.
PART NAME
QTY.
REMARKS
13320ZE2611
13351ZE2010
961006206000
CRANKSHAFT (L- TYPE)............................. 1 .......... INCLUDES ITEM W/
*
WEIGHT BALANCER
BEARING, RADIAL BALL (6206)
1
1
12
*
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 104 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
2
3
6
7
8
*
9
10
11
12
13
PART NO.
PART NAME
QTY.
REMARKS
12000ZE2834
15510ZE2043
16541ZE2010
90131896650
90446KE1000
91201890003
91353671003
9405010000
031112230
CYLINDER ASSY., BALANCER + OIL ALERT ...... 1 .......... INCLUDES ITEMS W/
*
SWITCH ASSY., OIL LEVEL
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER 8.2 X17X0.8
OIL SEAL 30X46X8
O-RING 14MM ARAI
NUT FLANGE 10MM
WASHER, DRAIN PLUG 12MM
PIN, LOCK 10MM
BOLT, FLANGE 6X12
BEARING, RADIAL BALL 6202
BOLT, FLANGE 6X12 CT200
ALERT UNIT, OIL
1
1
2
1
1
1
1
2
1
2
1
1
1
9425110000
957010601200
961006202000
90013883000
34150ZH7003
14
15
16
*
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 106 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12200ZH9000
12204ZE2306
12205ZE2305
12216ZE2300
12251ZE2800
12310ZE2020
12391ZE2020
14775ZE2010
90014ZE2000
90042ZE2000
92900080320E
90441ZE2010
9430112200
CYLINDER HEAD COMP. ....................................... 1 .......... INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
6
7
GUIDE, VALVE, OS, OPTIONAL
GUIDE, EX. VALVE, OS, OPTIONAL
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP., HEAD
GASKET, CYLINDER HEAD COVER
SEAT, VALVE SPRING
BOLT, HEAD COVER
BOLT, STUD 8X123
BOLT, STUD 8X47
WASHER COMP., HEAD COVER
PIN A, DOWEL 12X20
BULK HOSE, VACUUM 11X1000, 11X100
BOLT, FLANGE 10X80
1
1
1
1
1
1
1
1
2
2
1
2
1
4
1
1
8
10
11
12
13
14
15
16
17
17
950051100130M
957011008000
9807956846
SPARK PLUG, BPR6ES, NGK
SPARK PLUG, W20EPR-U, DENSO
9807956855
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 107
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 108 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
3
4
5
7
9
PART NO.
PART NAME
QTY.
REMARKS
16731ZE2003
19610ZE2010ZC
19631ZE2D00
32197ZH8003
36100ZE1015
90013883000
90684ZA0601
CLIP, TUBE
1
1
1
1
1
6
1
COVER COMP., FAN *NH1* BLACK
SHROUD
SUB-HARNESS
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE 6X12, CT200
CLIP, WIRE HARNESS
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 109
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 110 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
7
PART NO.
PART NAME
QTY.
REMARKS
19511ZE2000
28450ZE2W11
31100ZE2010
90201ZE3V00
90741ZE2000
FAN, COOLING
1
1
1
1
1
PULLEY COMP., STARTER, SCREEN GRID
FLYWHEEL COMP.
NUT, SPECIAL 16MM
8
KEY, SPECIAL WOODRUFF 25X18
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 111
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 112 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
1
6
3
1
5
REMARKS
18310ZE2W00
18320ZE2W01
18323ZE2W00
18330ZE2W00
18331ZE2810
18333ZK6Y00
18355ZE2010
18381ZE2W10
18381ZE2800
90013883000
90050ZE1000
90055ZE1000
90050ZE1000
9405008000
MUFFLER
PROTECTOR, MUFFLER
PROTECTOR, EX. PIPE
PIPE, EX.
CAP, MUFFLER
GASKET, EX. PIPE
ARRESTER, SPARK
GASKET, MUFFLER (ARRESTER)
GASKET, MUFFLER
BOLT, FLANGE (6 X 12) (CT200)
SCREW, TAPPING (5 X 8)
SCREW, TAPPING (4 X 6)
SCREW, TAPPING (5 X 8) (OPTIONAL)
NUT, FLANGE (8MM)
9
10
11
12
13
14
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 113
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 114 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
5
6
*
8
11
12
13
14
15
PART NO.
PART NAME
RUBBER SUPPORTER 107MM
JOINT, FUEL TANK
TANK COMP., FUEL *NH1*, BLACK
CAP COMP., FUEL FILLER .................................... 1 .......... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
FILTER, FUEL
O-RING 14MM, ARAI
NUT, FLANGE 8MM
BULK HOSE, FUEL 4.5X3000, 4.5X222
CLIP, TUBE, B8
BOLT, FLANGE 8X25
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE2010ZD
17620ZH7023
17631ZH7003
17672ZE2W01
91353671003
9405008000
1
1
1
*
1
1
1
2
1
2
2
950014500360M
9500202080
957010802500
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 115
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — IGNITION ASSY.
IGNITION COIL ASSY.
PAGE 116 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2ENGINE — IGNITION ASSY.
IGNITION COIL ASSY.
NO.
1
2
6
8
PART NO.
PART NAME
QTY.
REMARKS
30500ZF6W02
30700ZE1013
31512ZE2000
36101ZE1010
90015883000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
GROMMET, WIRE
1
1
1
1
2
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6X28
11
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 117
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 118 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.
PART NAME
QTY.
REMARKS
13010ZE2013
13011ZE2013
13012ZE2013
13013ZE2013
13101ZE2W00
13102ZE2W00
13103ZE2W00
13104ZE2W00
13111ZE2000
13200ZE2000
13200ZE2305
90001ZE8000
90551ZE1000
RING SET, PISTON, STD.
RING SET, PISTON, OS 0.25, OPTIONAL
RING SET, PISTON, OS 0.50, OPTIONAL
RING SET, PISTON, 0.75, OPTIONAL
PISTON, STANDARD
1
1
1
1
1
1
1
1
1
PISTON, OS 0.25, OPTIONAL
PISTON, OS 0.50, OPTIONAL
PISTON, 0.75, OPTIONAL
PIN, PISTON
ROD ASSY., CONNECTING STANDARD ................ 1 .......... INCLUDES ITEMS W/
ROD ASSY., CONNECTING, US 0.25, OPT.
BOLT, CONNECTING ROD
*
1
2
2
CLIP, PISTON PIN 18MM
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 119
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 120 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZE2W01ZB
28410ZE2W01ZB
28421ZE2W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28461ZE2W02
28462ZE2W11
90004ZE2W01
90008ZE2003
STARTER ASSY., RECOIL *NH1*, BLK ............... 1 ......... INCLUDES ITEMS W/
*
2
CASE COMP., RECOIL STARTER *NH1*, BLK
PULLEY, RECOIL STARTER
RATCHET, STARTER
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING RATCHET
RETAINER, SPRING
GRIP, STARTER
ROPE, RECOIL STARTER
SCREW, CENTER
BOLT, FLANGE 6X10
1
1
2
1
1
2
1
1
1
1
3
*
3
*
4
*
5
*
6
*
7
8
*
*
10
*
11
*
13
*
14
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 121
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
PAGE 122 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY.
GEAR REDUCTION ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
11500ZE2620
11521ZE2800
22103ZE2620
23220ZE2621
23710ZE2621
90401ZE2620
90402ZE2620
90473842000
90745ZE2600
91201890003
9430108140
COVER ASSY, REDUCTION CASE ............. 1 .......... INCLUDES ITEMS W/
*
GASKET, CHAIN CASE COVER
GEAR, PRIMARY DRIVE (17T)
COUNTERSHAFT
SHAFT, P.T.O. (H- TYPE)
SHIM A (OPTIONAL)
SHIM B (OPTIONAL)
WASHER (8MM)
1
1
1
1
AR
AR
1
1
1
2
1
6
1
9
KEY (6.3 X 6.3 X 43)
10
11
12
13
OIL SEAL (30 X 46 X 8)
PIN A, DOWEL ( 8 X 14)
BOLT, FLANGE (8 X 25)
BOLT, FLANGE (8 X 40)
BEARING, RADIAL BALL (6206)
BEARING, RADIAL BALL (6302)
*
957010802500
957010804000
961006206000
961006302000
14
15
*
*
1
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 123
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — LABEL ASSY.
LABEL ASSY.
PAGE 124 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1HA2 ENGINE — LABEL ASSY.
LABELS ASSY.
NO.
1
2
3
5
15
16
PART NO.
PART NAME
QTY.
REMARKS
87521ZE2W01
87522ZE1810
87522ZH9000
87528ZE2810
87586ZH7W00
87532ZH8810
EMBLEM, INTERNAL
MARK, CAUTION, EXTERNAL
LABEL, CAUTION
1
1
1
1
1
1
MARK, CHOKE, EXTERNAL
LABEL, FUEL CAUTION
MARK, OIL ALERT
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 125
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
Terms And Conditions Of Sale
STOW Construction Equipment
PAYMENTTERMS
DROP SHIPMENTS
The sender will be notified of any material
received that does not meet the above
provisions. Such material will be held for 30
days from notification pending instructions.
If a reply is not received within 30 days, the
material will be returned to the sender at his
expense with no credit issued.
Terms of payment for unit sales are 2% 15
days net 30 days from date of invoice unless
otherwise specifically stated on our invoice.
Parts invoices have terms of net 10 days.
Minimum parts billing is $15.00 net.
STOW reserves the right to refuse Drop
Shipments outside the normal service area
of the purchasing dealer.
FIELD WAREHOUSES
Field Warehouses are currently located in
California, Georgia, Idaho, Iowa, and New
Jersey
Applicable discounts will be computed on
merchandise value only. Late charges will be
assessed at prevailing rates. Cash discounts
cannot be taken on current billings if any
previously billed amounts are past due.
PRICING, REBATES AND SPECIFICATIONS
Every effort will be made to provide adequate
notice of changes; however, prices and
equipment specifications are subject to
change without notice.
SPECIAL EXPEDITING SERVICE
The higher of a $35.00 surcharge or actual
costs will be added to the invoice for special
handling, including bus shipments, or in cases
where STOW personnel must personally
deliver the equipment or parts to the carrier.
FREIGHT POLICY
Price changes are effective on a specific date
and all orders received on or after that date
will be billed at the revised price.
Freight policy is established to offer customers
every advantage possible. Due to bulk freight
ratings on some equipment and other shipping
considerations, freight policies differ by
equipment type. Actual back freight may be
charged for shipments originating from other
than specified FOB warehouses.See Freight
Policy for details.
RETURNED GOODS POLICY
Rebates for price reductions and added
charges for price increases will not be made
for stock in dealer inventory at the time of a
price change.
Return shipments may be accepted and credit
allowed, subject to the following provisions.
1. A Returned Material Authorization (RMA)
must be approved by STOW prior to
shipment. Approvals for returned goods
must be with just cause and are at the
sole discretion of STOW. A copy of the
Authorization must accompany the
shipment to the designated Warehouse.
STOW reserves the right to quote and sell
direct to Government agencies and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
All STOW domestic sales are FOB nearest
available designated MQ/STOW warehouse.
Export orders are ex-works factory located in
Carson, CA or Boise, ID.
Additions to orders already shipped cannot be
accepted for freight minimums.
LIMITATION OF SELLER’S LIABILITY
2. Parts being returned must be listed as
currently supplied on the current parts
list.
STOW shall not be liable hereunder for
damages in excess of the purchase price
of the item with respect to which damages
are claimed and in no event shall STOW be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
Should STOW elect to make partial shipments
of an order originally complying with the
“freight allowed” requirements, transportation
charges will be absorbed by STOW on any
subsequent shipment applying to that order.
3. Parts must be in new and resalable
condition in the original package, with
part numbers clearly marked.
4. Units and accessories must be current
models in the latest price list and in new
and resalable condition.
All other orders will be shipped collect or
prepaid with charges added to the invoice.
STOW’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must
be settled between the consignee and the
carrier.
LIMITATION OF WARRANTIES
There are no warranties, express or implied,
made by STOW. hereunder on Products
manufactured or distributed by it except the
warranty against defects in material and
workmanship on new Products to the original
purchaser, as set forth in the STOW New
Product Limited Warranty.
5. Special order items are not returnable
for credit.
6. Credit on returned parts and units will be
issued at actual dealer net price at time of
purchase less 15% restocking charge.
Parts:FOB Carson, California or Boise, Idaho.
See Freight Policy for details and additional
discounts.
7. All returned shipments are to be made
to the STOW designated receiving point,
freight prepaid at the sender’s expense.
Effective: July 15, 2003
STOW CONSTRUCTION EQUIPMENT
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
ꢀꢁꢂꢃꢄꢄꢁꢃꢅꢆꢅꢆ s ꢇꢈꢈꢃ"59ꢃ34/7
FAX: 310-604-9237
E-MAIL: [email protected]
www.stowmfg.com
!TLANTA s "OISE s .EWARK s 1UEBECꢉ #ANADA
-ANCHESTERꢉ 5+ s 2IODE*ANEIROꢉ "2 s 0UEBLAꢉ -8
PAGE 126 — STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
STOW MS-63 MIXER — OPERATION AND PARTS MANUAL — REV. #5 (03/26/10) — PAGE 127
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
PARTSDEPARTMENT
800-427-1244
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
800-478-1244
310-537-3700
FAX: 310-537-4259
^^^^*^6668
800-478-1244
FAX: 310-631-5032
800-421-1244, EXT. 279 FAX: 310-537-1173
310-537-3700, EXT. 279
310-661-4242
FAX: 310-604-9237
877-289-7869 (877-BUY-STOW)
© COPYRIGHT 2007, MULTIQUIP INC.
Multiquip Inc, and the STOW logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical
data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications,
design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
MQSTOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 888-252-MQ STOW [888-
252-7869]
Atlanta • Boise • Newark • Quebec, Canada
Manchester, UK • Rio de Janeiro, BR • Puebla, MX
FAX: 310-537-1986 • FAX: 800-556-1986
E-MAIL: MQ [email protected] • WWW:
stowmfg.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|