ST IG A P A RK
2WD
110 Co mbi Pr o
125 Co mbi Pr o
8211-0546-03
Download from Www.Somanuals.com. All Manuals Search And Download.
10
9
1/3
12
11
D
13
24 Nm
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ENGLISH
1 GENERAL
2 DESCRIPTION
This symbol indicates WARNING. Seri-
ous personal injury and/or damage to
property may result if the instructions
are not followed carefully.
You must read these instructions for use
and the machine’s safety instructions
carefully.
2.1 General
The cutting deck is intended for use on Stiga’s 2-
wheel drive Park machines.
The cutting deck is supplied in one of the follow-
ing versions:
•
With manual adjustment of cutting height.
•
With electrical adjustment of cutting height.
1.1 Symbols
The following symbols appear on the machine.
They are there to remind you of the care and atten-
tion required in use.
2.2 Controls, 125 Combi Pro
2.2.1 Cutting height adjustment
The cutting height can be adjusted between 25 and
90 mm.
Electrical cutting height adjustment
The setting can be adjusted infinitely variably us-
ing a switch on the machine.
This is what the symbols mean:
Warning!
Read the instruction manual and the safety
manual before using the machine.
Manual cutting height adjustment
The setting can be adjusted to a number of fixed
positions using the lever. See fig. 1.
Warning!
Do not insert your hands or feet under the
cover when the machine is in operation.
2.2.2 Incline forwards
The rear section of the cutting deck can be raised
12 mm by moving the two pins down one hole
from the basic setting. See fig. 2.
Warning!
Watch out for discarded objects. Keep on-
lookers away.
2.2.3 Rear mounting
The cutting deck’s rear section is secured with the
pins in fig. 2.
Warning!
Before starting repair work, remove the
spark plug cable from the spark plug.
2.2.4 Mounting in implement lifter
The deck is mounted in the implement lifter with a
chain and snap hooks.
One snap hook is intended for the working position
and can be moved in the chain links to set the lift-
ing force.
1.2 References
1.2.1 Figures
The other snap hook is intended for the washing
position.
The figures in these instructions for use are num-
bered 1, 2, 3, etc.
Components shown in the figures are marked A, B,
C, etc.
A reference to component E in figure 5 is written
“5:E”.
3 ASSEMBLY
3.1 Installing
1. Place the cutting deck in position in front of the
machine.
1.2.2 Headings
The headings in these instructions for use are num-
bered in accordance with the following example:
“2.3.2” is a subheading to “2.3” and is included un-
der this heading.
When referring to headings, only the number of the
heading is normally specified. E.g. “See 2.3.2”.
2. Install the deck mounts on the machine’s steer-
ing knuckles. See fig. 3.
3. Remove the pins and the washers on both sides.
See fig. 2.
4. Screw the arms into each other. See fig. 4.
5. Suspend the cutting deck in the implement lift-
er. See fig. 5.
6. If the deck has electrical cutting height adjust-
ment, connect the cable to the machine’s front
right socket. See fig. 7.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ENGLISH
3.2 Belt
4.3 Mowing advice
In order to achieve optimum mowing results, fol-
low the advice below:
The cutting deck’s rear section should rest on the
floor (it should not be lifted or secured).
Install the belt as follows:
1. Set the maximum cutting height.
2. Locate the belt around the machine’s belt pulley
(8:B).
3. Tension the belt with the belt idler (8:A)B. The
belt idler should be on the left side of the belt
viewed from the driver’s position.
•
•
•
•
•
Cut frequently.
Run the engine at full throttle.
The grass should be dry.
Use sharp blades.
Keep the underside of the cutting deck clean.
125 Combi Pro can cut the grass in the following
two ways:
•
•
4. Lift up and secure the rear section of the cutting
deck.
Mulching: composting and spreading.
Rear ejection: ejects the grass in a line behind
the deck.
On machines with 17” wheels: Install the wash-
ers and the pins in the top hole. See fig. 2.
On machines with 16” wheels: Install the wash-
ers and the pins in the middle hole. See fig. 2.
The deck is set for mulching on delivery. In order
to eject the grass in a line behind the deck, the plug
in fig. 6 must be removed.
Set the deck in service position (see 5.3) in order to
remove/install the plug.
3.3 Tyre pressure
Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).
5 MAINTENANCE
4 USING THE MACHINE
Check that the grass that is to be cut is
completely free of foreign objects such
as stones etc.
5.1 Preparation
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
4.1 Cutting height
The best cutting results are achieved when the
when the top third of the grass is cut off. I.e. 2/3 of
the length of the grass remains. See fig. 9.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
If the grass is long and has to be cut significantly,
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn
surface is uneven. This would entail a risk of the
blades being damaged against the surface and the
lawn’s top layer of soil being removed.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable from the spark plug and remov-
ing the ignition key.
4.2 Incline
The cutting deck’s rear section can be lifted so that
the deck has a greater forward incline than that
provided by the basic setting. This incline affects
the cutting results as follows.
5.2 Washing position
1. Activate the parking brake.
2. Set the implement lifter in transport position.
3. Set the highest cutting height.
4. Remove pins and washers. See fig. 2.
5. Grip the front edge of the deck and lift up. Hook
on the chain so that the deck is pointing diago-
nally upwards. See fig. 10.
It is absolutely forbidden to start the engine
when the deck is in the washing position.
4.2.1 No incline
When the deck is in the basic setting, the best
mulching effect and good dispersion of the cut
grass are achieved. The basic setting is recom-
mended for normal grass.
4.2.2 Incline
When the cutting deck is inclined forwards, the
mulching effect is reduced while the cut grass is
dispersed better.
Reset in accordance with 3.2, point 4.
Inclining forwards is recommended for thicker
grass.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ENGLISH
5.3 Service position
6 SPARE PARTS
1. Activate the parking brake.
2. Set the implement lifter in transport position.
3. Set the highest cutting height.
4. If the deck has electrical cutting height adjust-
ment, disconnect the cable from the machine.
See fig. 7.
5. Remove pins and washers. See fig. 2.
6. Hook the belt idler arm on the mount (8:C)
7. Force the belt off the centre pulley (8:B).
8. Grip the front edge of the deck and lift up. Lift
until the deck is completely vertical and rest the
rear edge on the floor. See fig. 11.
STIGA genuine spare parts and accessories are de-
signed specifically for STIGA machines. Please
note that ‘non-genuine’ spare parts and accessories
have not been checked or approved by STIGA:
The use of such parts and accessories
can affect the function and safety of the
machine. STIGA accepts no responsi-
bility for damage or injuries caused by
such products.
Reset in accordance with 3.1.
7 DESIGN REGISTRATION
This product or parts thereof is covered by the fol-
lowing design registration:
5.4 Cleaning
The underside of the deck must be cleaned after
each use.
Set the deck in washing position.
Clean the underside of the deck carefully. Use a
high-pressure washer, scraper and/or brush.
When the surfaces are completely dry and clean,
touch up the paintwork. Use durable yellow paint
intended for metal outdoors.
Sweden: 66 166
Germany: 499 11 740.9
France: 577 251-253, 577 439-443
USA: 435 564
5.5 Wheels
125 Combi Pro is fitted with two lubricating cups
(12:D) for the vertical shafts.
The grease nipples must be lubricated with univer-
sal grease after 50 hours of operation.
5.6 Replacing blades, fig. 13
Wear protective gloves when changing
blade(s) to avoid cutting yourself.
Check that the blades are always sharp.
This produces the best cutting results.
Always check the blade(s) after a collision. If the
blade system has been damaged, defective parts
should be replaced.
Always use genuine spare parts. Non-
genuine spare parts can entail a risk of
injury, even if they fit the machine.
The full blade is replaced when the edges
are worn.
Install the new blade with the punched text facing
down.
Tightening torque: 24 Nm
5.7 Wear protection
There are two wear protection devices on the un-
derside of the cutting deck to protect it. These can
be replaced if necessary.
GGP reserves the right to make alterations to the
product without prior notification.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Box 1006 SE-573 28 TRANÅS
GGP Sweden AB
·
·
Download from Www.Somanuals.com. All Manuals Search And Download.
|