ST IG A
Silex 500-G
Silex 500R-G
BRUKSANVISNING SV ....4
KÄYTTÖ O HJEET FI ...10
BRUGSANVISNING DA..16
BRUKSANVISNING NO .22
GEBRAUCHSANW EISUNG DE...28
INSTRUCTIO NS FO R USE EN...35
MO DE D’EMPLO I FR....41
GEBRUIKSAANW IJZING NL...49
ISTRUZIO NI PER L’USO IT.....56
INSTRUCCIO NES DE USO ES....63
INSTRUÇõES DE UTILIZAÇÃO PT ...70
INSTRUKCJA O BS£UGI PL....77
»HC“P”K÷»fl œOÀ‹«Œ¬¿“EÀfl RU...84
NÁVO D K PO U®ITÍ CZ ..92
HASZNÁLATI UTASÍTÁS HU..98
NAVO DILA ZA UPO RABO SL..105
8214-2210-80
Download from Www.Somanuals.com. All Manuals Search And Download.
5
4
C
D
E
F
G
J
H
I
7
6
1
2
4
3
8
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
ENGLISH
•
Set the throttle control in the "Stop" position,
and close the petrol cock when the machine has
been stopped.
Switch off the engine before transporting the
machine. Never lift the machine by yourself.
The machine is lifted by two persons, one on
each side holding the steering and the rotor ax-
le. Wear protective gloves and hold the machine
upright when lifting.
1 SYMBOLS
The following symbols can be found on the rotary
cultivator/in these instructions. These will provide
a reminder of the care and attention that is required
during operation. If any symbol is missing, has
been damaged or is illegible, it must immediately
be replaced with a new one.
•
•
This is what the symbols mean:
Warning! Read the owner’s manual before
operating the machine.
When the machine is loaded on a trailer or tail-
board it should be run up on a ramp by using its
wheel.
Warning! Rotating blade.
2.2 PREPARATIONS
•
Before starting work, remove all foreign objects
such as stones, glass, cables, metal objects and
other loose objects.
Toys, hoses and other objects can be damaged.
Check that the tiller is in good condition before
using it.
Warning! This symbol highlights impor-
tant text in these instructions. Risk of seri-
ous personal injury or damage to the
machine if the instructions are not fol-
lowed.
•
•
•
Check that all nuts and bolts are tightened.
2 SAFETY INSTRUCTIONS
2.1 GENERAL
2.3 OPERATING
•
•
•
•
•
•
Always operate the machine at low speed when
working on stony ground.
Do not change the engine's speed setting. The
engine must not be overspeeded.
The work area should be well illuminated dur-
ing the work.
The tiller must not be used when other persons,
especially children, are in the vicinity.
The tiller must not be used without the splash-
guards or protective cover.
The tiller must not be used if the operator is ill,
has taken medicine, or is under the influence of
other substances which reduce one's reactions.
The tiller must not be used on terrain which
slopes more than 20°.
The user is responsible to ensure that all risks in
the terrain are taken into consideration, and that
procedures are taken to prevent accidents. This
particularly applies to sloping, slippery or loose
terrain.
Start the engine carefully, according to the in-
structions in this manual. No parts of the body
must come in contact with the rotors.
The engine must never be started in an enclosed
area.
•
Read through this instruction book carefully
and make sure you understand the contents be-
fore using the tiller.
•
The tiller must only be used for gardening pur-
poses.
•
•
Keep children away from the tiller.
Do not allow children or persons who have not
read the instructions to handle the tiller.
The tiller is manufactured in accordance with
current standards, and must not be modified or
rebuilt.
•
•
•
All the symbols on the tiller should be kept in-
tact.
The user is liable for damages incurred by a
third party.
•
•
WARNING for petrol. Petrol is highly inflam-
mable: Petrol must be stored in the requisite
containers.
•
Always fill-up outdoors and with the engine
switched off.
•
•
•
Do not smoke when filling-up.
There must be no naked flames or other sources
of heat in the vicinity of the petrol.
Do not start the engine if petrol has spilled out.
Move the machine and allow the petrol to evap-
orate before starting the machine.
•
•
•
•
The carbon monoxide in the engine's exhaust
fumes is poisonous and can cause death.
Screw on the filler cap correctly after filling up.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
ENGLISH
•
•
•
Wear tightly fitting clothes and heavy-duty
shoes which completely cover the feet.
The tank should only be half full when operat-
ing on slopes. Petrol can leak out.
The engine must be stopped in the following
circumstances:
When the machine is left unattended
Before the machine is filled up with petrol
Always make sure you have a good footing, es-
pecially on slopes.
Check that no one is in front of you or beside
you when starting the blades. Keep a steady
grip on the steering. The machine will lift when
the rotors are started. Use extra caution when
backing.
Always keep at a safe distance to the rotors
when working.
Holding the steering correctly ensures a safe
distance.
No person must come closer than 20 m to the
machine when working on slopes. The user
must hold the steering firmly with both hands
all the time.
Working on stony or hard ground demands ex-
tra attention from the operator. The machine be-
comes more unstable.
Never touch the engine when operating the ma-
chine, or just afterwards. Risk for burn injuries.
jury. If the muffler is damaged it must be re-
placed.
The engine must be stopped and the spark plug
lead disconnected in the following circumstanc-
es:
•
When adjusting the rotors.
•
•
•
When the machine is to be cleaned or repaired.
When checking after a collision with a solid
hard object. Carry out the necessary repairs be-
fore continuing to work.
•
If the machine begins to vibrate abnormally.
Carry out the necessary repairs before continu-
ing to work.
Wear protective gloves when working with the
rotors.
•
•
•
•
3 ASSEMBLY
3.1 Auxiliary wheel
Install the auxiliary wheel (2:F) in the front hole
and lock using the locking pin (2:A).
3.2 Depth skid
Install the depth skid (3:G) in the middle hole at
the rear and lock using the locking pin (3:B).
•
•
3.3 Handle
Install the handle’s base (4:G) with handle (4:E) as
follows:
1. Position the base (4:G) on the machine.
2. Remove the four screws (4) with the washers
(4:H). Do not tighten the screws yet.
3. Hold the right and left handle (4:E ) in place and
install using the two screws (4:F) with nuts and
washers (4:C+D). Tighten the screws.
4. Set the handle to a comfortable working height
and tighten the screws (4:H).
2.4 AFTER OPERATING
•
Allow the engine to cool before putting the ma-
chine in a storeroom. Fire risk!
Remove dirt and foreign material before putting
the machine in a storeroom. The area round the
petrol tank and muffler must be kept clean from
leaves, oil, petrol or other foreign materials.
Fire risk!
If the petrol tank is to be emptied, do this out-
doors and when the engine is cold. Fire risk!
The machine should be stored in a dry place.
The machine must not stored with fuel in the
tank in rooms where there are naked flames,
sparks or other strong sources of heat.
•
•
•
3.4 Throttle control
Install the throttle (1:A) on the left handle. See fig.
6.
3.5 Throttle cable
1. Install the throttle cable on the engine if not al-
ready installed. See the engine supplier’s man-
ual.
2.5 MAINTENANCE
•
Carry out maintenance regularly. All nuts and
bolts should always be tight.
Only use genuine spare parts which are in good
condition. Spare parts must not be repaired.
They must be replaced if they are defective.
Poor quality spare parts can lead to personal in-
2. Install the cable in the throttle. See fig. 7.
•
36
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
ENGLISH
3.6 Cable for reverse control
Only applies to 500R-G.
The cable is marked R.
4.4 Handle (1:B)
The handle has two handgrips that are used to op-
erate the machine over the area to be cultivated.
1. Hook the cable in the reverse control (1:C) and
insert the cable in the gap in the cable housing’s
mounting on the left handle.
4.5 Fuel cap
See the accompanying engine manual.
Unscrew the fuel cap to fill with petrol. The fuel
cap must always be closed during operation.
2. Adjust the cable sleeve if necessary.
3.7 Drive cable
4.6 Angle adjustment handle (1:E)
Release the knob and set the handle to the desired
angle.
1. Hook the cable in the drive control (1:D) and in-
sert the cable in the gap in the cable housing’s
mounting on the left handle.
Then retighten the knob again.
2. Adjust the cable sleeve if necessary.
4.7 Height adjustment handle (1:F)
Slacken off the screws and set the handle to the de-
sired height.
3.8 Front protection
Install the front protection (5:J). Use the screws
supplied.
Then retighten the screws again.
4.8 Oil filling/draining
Always check the oil level before start-
ing the engine.
4 DESCRIPTION
The rotary cultivator is driven by a four-stroke en-
gine and is intended for soil cultivation in private
gardens. The most important parts and controls of
the rotary cultivator are described below.
See the accompanying engine manual.
Plug for oil filler and checking the oil level.
4.1 Reverse control (1:C)
Only applies to 500R-G.
To drain the oil, the machine must be tilted so that
the oil runs out from the same hole.
The control is used to start the rotor for reverse
when the engine is running.
The reverse control and drive control (1:D) must
never be activated at the same time.
4.9 Auxiliary wheel (1:H)
The auxiliary wheel is intended to assist transport
of the machine and has two positions.
•
The auxiliary wheel must not be installed when
carrying out work.
Control in idle mode (forward) – No drive.
•
The auxiliary wheel must be installed when
transporting.
Control moved backwards – The machine
reverses.
Remove/install the auxiliary wheel as follows:
1. Pull out the locking pin (2:A).
2. Remove the auxiliary wheel downwards.
3. Reinstall the locking pin in the auxiliary wheel
arm.
Install in reverse order
4.2 Drive control (1:D)
The control is used to start the rotor for forward
motion when the engine is running.
The reverse control (1:C) and drive control must
never be activated at the same time.
Control in idle mode (down) – No drive.
4.10Rotors (1:J)
Nobody must be close to the dangerous
rotors during operation.
Control pulled in – Forward operation.
The rotors are made of special steel and work
the soil at the same time as the machine is pro-
pelled forwards.
4.3 Throttle and stop (1:A)
The control determines the engine’s rpm and has
start and stop positions.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
ENGLISH
4.11Cutting disc (1:K)
5 OPERATION
Nobody must be close to the dangerous
cutting discs during operation.
5.1 Fuel
The cutting discs are on respective rotor
axles and are designed to border the working area
and facilitate control of the machine.
Read and understand all safety instruc-
tions.
No fires or smoking near to petrol.
Use 92-95 octane lead free petrol.
Oil-mixed petrol designed for 2-stroke engines
must never be used.
4.12 Choke
The choke must never be activated dur-
ing operation. This will damage the en-
gine.
Filling
Read and understand all safety instruc-
tions.
If the engine has been running, wait a
few minutes until it has cooled before
filling up.
See the accompanying engine manual.
The choke must be activated at cold starts.
4.13 Starting handle
See the accompanying engine manual.
Fill carefully to prevent the spillage of
fuel.
Move the rotary cultivator at least 3 me-
tres from the filling site before starting.
Handle for starting the engine.
4.14Depth skid (1:G)
The task of the depth skid is to keep the machine
stable so that the soil can be cultivated.
The depth skid has three positions. Shifting takes
place as follows:
1. Pull out the locking pin (3:B).
2. Pull out the depth skid and reinstall in the de-
sired position.
3. Reinstall the locking pin.
The different operating properties are shown ac-
cording to the table below:
Fill as follows:
1. Clean around the fuel cap.
2. Unscrew the filler cap.
3. Fill using a funnel or use a filler can with spout
to prevent spillage.
4. Tighten the filler cap.
5. Move the rotary cultivator at least 3 metres
from the place of filling before starting.
Move the rotary cultivator at least 3 me-
tres from the filling site before starting.
Holes
Left
Properties
The machine works itself for-
ward , angled to the left.
The machine works itself for-
ward without being angled to
either side.
The machine works itself for-
ward, angled to the right.
5.2 Engine Oil
Middle
Right
Always check the oil level before start-
ing. Otherwise there is a risk of serious
engine damage.
Also see “4.8”. Check the oil level as follows:
1. Position the machine so that the engine is hori-
zontal.
2. Unscrew the oil filler and check that the oil lev-
el is at the upper mark on the dipstick. See the
accompanying engine manual.
3. Top up the oil if necessary. Use normal engine
oil SAE 10W-30.
4. Reassemble the oil filler cap.
Move the rotary cultivator at least 3 me-
tres from the filling site before starting.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
ENGLISH
5.2.1 Starting the engine from cold
1. Put the choke in position “CHOKE”. See the
accompanying engine manual.
6 STORAGE
Store the rotary cultivator in a dry place. Also see
section “Safety instructions”.
2. Set the throttle (1:A) in the “START” position.
3. Hold the handle with one hand and slowly pull
the starter handle with the other hand. See the
accompanying engine manual. When the starter
mechanism engages, quickly and forcefully pull
the starter handle until the engine starts.
NOTE! Do not pull the cord hard to its stop po-
sition and do not release it in the pulled out po-
sition. This damages the starter mechanism.
After draining the petrol, start the engine and allow
it to run until it runs out of petrol.
7 MAINTENANCE
WARNING!Repairsmustbe carried out
by the dealer. Otherwise the guarantee
becomes invalid.
WARNING!Before carrying out repairs
and maintenance, the spark plug con-
nection must be disconnected.
5. Reset the choke after 3-5 seconds.
5.2.2 Starting a warm engine
Start a hot engine according to points 2 and 3
above. The choke/primer must not be used.
7.1 Periodic maintenance
Before each operation
5.3 Operating
1. Tip the rotary cultivator back slightly so that the
rotor is above ground.
2. Activate the drive control (1:D).
3. Tilt the cultivator forward so that it works its
way into the soil.
•
Check for fuel leaks.
•
Check that all screws are tightened.
After each operation
•
Clean the rotary cultivator.
•
Check for fuel leaks.
Every 25 operating hours and every 3 months
4. If the machine has a reverse control, activate it
(1:C).
•
Check, clean or replace the air filter.
•
Check that all screws and nuts are tightened.
5.4 Stop
7.2 Air filter
See the accompanying engine manual.
Stop the rotary cultivator by setting the throttle and
stop control (1:A) to “STOP”.
Do not use flammable liquids when
cleaning.
Serious engine damage can be caused if
the machine is operated with a defective
or blocked filter.
5.5 Operating tips
The rotors propel the machine forward. The speed
of the rotors is controlled by the throttle (1:A).
Keep hands and feet away from rotating
parts (1:J, K).
The paper filter must never be cleaning
with liquid.
The optimum working depth varies with soil con-
ditions. The working depth is determined by how
hard the depth skid is pushed down during propul-
sion. Operate and test.
The machine is equipped with a pre-filter (foam
rubber) and a main filter (paper).
Drive 2-3 times in different directions for best re-
sults.
Never operate the machine in wet soil. Clumps of
earth are created that are then difficult to break-up.
Hard and dry soil requires an extra run, at right an-
gles to the first.
Clean/replace the air filter every 3 months or every
25 operating hours. During operation in dry and
dusty conditions, the air filter must be cleaned/re-
placed every day.
Clean/replace the air filter as follows:
1. Undo the screws or locking tabs and the filter
housing.
2. Grasp the main filter (paper) and shake it a few
times against a hard surface or blow clean with
compressed air from the inside out.
WARNING! Never overload a new ma-
chine. Drive carefully for the first 5
hours.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
ENGLISH
3. Wash the pre-filter (foam rubber) in liquid de-
tergent and water. Then carefully twist the filter
out and allow to dry.
4. When the pre-filter is dry, reinstall the filter in
reverse order.
Cause: Sparkplug fault.
Action: Replace spark plug.
Fault: Weak engine, does not run at full throttle
Cause: Blocked air filter
Corrective action: Clean or replace the air filter.
Fault: Stops during operation
Cause: No fuel.
The filters must be replaced if very dirty or defec-
tive.
Action: Fill with petrol
7.3 Spark plug
See the accompanying engine manual.
The sparkplug must be replaced in the following
cases.
8 SERVICE
Authorised service stations carry out repairs and
servicing. They always use genuine spare parts.
•
•
•
When the electrodes are burnt.
If the porcelain insulator indicates damage.
If the rotary cultivator is difficult to start.
Under no circumstances may parts oth-
er than genuine spare parts be used.
This is a requirement stipulated by the
Testing Authority. The machine is ap-
proved and tested with these parts.
If the machine requires servicing, repair
or maintenance that entails dismantling
of the cover, this must be performed by
an authorised service station.
The electrode gap should be 0.7-0.8 mm.
Use sparkplug Champion QC12YC or similar.
7.4 Changing the oil
Change the oil the first time after 2 hours of oper-
ation, and subsequently every 25 hours of opera-
tion or at least once a season. Change oil when the
engine is warm.
The manufacturer reserves the right to make alter-
ations to the product without prior notification.
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. So allow the engine to cool a few
minutes before draining the oil.
9 PURCHASE TERMS
1. Unscrew the cap for oil filling/oil draining. See
“4.8”.
2. Place a container on the floor.
3. Tilt the machine so that the hole is above the
container. See fig. 8.
A full warranty is issued against manufacturing
and material defects. The user must carefully fol-
low the instructions given in the enclosed docu-
mentation.
Warranty period
According to relevant laws.
Exceptions
The warranty does not cover damage due to:
3. Let the oil run out into the container.
5. Fill with new oil: See “5.2”.
7.5 Cleaning
Never use high-pressure washing equip-
ment when cleaning. This can cause wa-
ter to penetrate between the seals and
cause machine damage.
-
Neglect by users to acquaint themselves with
accompanying documentation
-
-
-
-
Carelessness
Incorrect and non-permitted use or assembly
The use of non-genuine spare parts
The use of accessories not supplied or approved
First brush off all dirt. Then wipe down the rotary
cultivator using a damp cloth. The underside can
be washed with water.
Neither does the warranty cover:
-
-
Wear parts
Normal wear
7.6 Fault-tracing
Fault: Difficult to start
The purchaser is covered the national laws of each
country. The rights to which the purchaser is enti-
tled with the support of these laws are not restrict-
ed by this warranty.
Cause: The fuel is too old.
Action: Drain the tank and fill with fresh petrol.
Cause: Sparkplug fault.
Action: Replace spark plug.
Fault: Engine runs unevenly
Cause: Contaminated fuel.
GGP reserves the right to make alterations to the
product without prior notification.
Action: Clean the petrol tank and carburettor.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
|