$30.00
Operation and Installation Manual
6017 Series
Large Hot Oil
Temperature Control Units
Important! Read Carefully Before Attempting to Install or Operate Equipment
Part No. 682.91540.00
Revision 3
Bulletin No. SC1-655-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Considerations
Sterling/Sterlco 6017 Series large hot oil temperature control units
are designed to provide safe and reliable operation when installed
and operated within design specifications, following national and
local safety codes.
To avoid possible personnel injury or equipment damage when
installing, operating, or maintaining this equipment, use good
judgment and follow these safe practices:
; Follow all SAFETY CODES.
; Wear SAFETY GLASSES and WORK GLOVES.
; Disconnect and/or lock out power before servicing or
maintaining the hot oil temperature control unit.
; Use care when LOADING, UNLOADING, RIGGING, or
MOVING this equipment.
; Operate this equipment within design specifications.
; OPEN, TAG, and LOCK ALL DISCONNECTS before
working on equipment. You should remove the fuses and carry
them with you.
; Make sure the hot oil temperature control unit and components
are properly GROUNDED before you switch on power.
; Do not jump or bypass any electrical safety control.
; Do not restore power until you remove all tools, test
equipment, etc., and the hot oil temperature control unit and
related equipment are fully reassembled.
; Only PROPERLY TRAINED personnel familiar with the
information in this manual should work on this equipment.
6017 Series Hot Oil Large Temperature Control Units
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1 General Information .................................................7
1-1
1-2
1-3
1-4
1-5
1-6
Introduction ..................................................................................... 7
Necessary Documents.................................................................... 7
Models Covered.............................................................................. 8
Standard Features .......................................................................... 8
Available Options ............................................................................ 9
Feature Descriptions....................................................................... 9
2 Shipping Information..............................................17
2-1
2-2
2-3
2-4
2-5
Unpacking and Inspection............................................................. 17
In the Event of Shipping Damages................................................ 17
If the Shipment is Not Complete.................................................... 18
If the Shipment is Not Correct....................................................... 18
Returns ......................................................................................... 18
3 Installation...............................................................19
3-1
3-2
3-3
3-4
Work Rules ................................................................................... 19
Installation Requirements.............................................................. 19
Connecting Piping......................................................................... 20
Making Electrical Connections ...................................................... 26
Page 4
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
4 Startup Preparations..............................................29
4-1
4-2
4-3
Starting the Unit ............................................................................ 29
Shutting Down the Unit ................................................................. 32
Returning Fluid to the Tank........................................................... 32
5 Using Controls and Indicators ..............................34
5-1
5-2
5-3
5-4
5-5
The Microprocessor Controller...................................................... 34
Identifying M2B Controller Panel Components.............................. 35
Using M2B Controller Keys........................................................... 37
Identifying Control Panel Switches................................................ 39
Identifying System Status Board Indicators................................... 41
6 Preventive Maintenance.........................................46
6-1
6-2
6-3
6-4
6-5
Periodic Checks ............................................................................ 46
Routine Servicing.......................................................................... 47
Draining the Unit for Storage......................................................... 50
Corrective Maintenance ................................................................ 50
Maintaining the Pump ...............................................See Addendum
7 Troubleshooting .....................................................52
6017 Series Hot Oil Large Temperature Control Units
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Charts and Figures
6017 Series Hot Oil Large Temperature Control Unit and
Specifications
1
16
16
24
34
39
41
2
3
4
5
6017 Unit Piping Setup
Typical Flow Schematic
Typical M2B Graphic and Button Control Panel
Control Panel Switches
6
System Status Board Indicators
Page 6
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
1
General Information
1-1 Introduction
Your Sterling/Sterlco 6017 Series hot oil temperature control unit
circulates thermal transfer-type oil through your process and to
precisely, automatically, and reliably maintain it at a temperature
you can select. The operating range of your temperature control
unit is from 100°F to 550°F (38°C to 288°C). The unit is best
suited for use with SterlTherm™ Heat Transfer Fluid. A
recommended list of commercially available heat transfer fluids
can be obtained through Sterling Customer Service.
Rapid recirculation of the fluid provides a close and uniform
temperature relationship between the TO PROCESS and FROM
PROCESS lines. This does, of course, depend on the configuration
of your process, and any restrictions within the mold.
This recirculation, combined with the immersion heater and
optional cooling capability, gives fast and accurate response to
bring the fluid up to temperature, or to changes in the settings
when needed.
Performance is assured through matching the unique Sterlco
controllers to the Sterlco high temperature system. The two
systems are fully integrated to achieve accurate control.
1-2 Necessary Documents
The following documents are necessary for the safe installation,
operation, and maintenance of your Sterling/Sterlco 6017 Series
hot oil large temperature control unit. You can obtain additional
copies from Sterling, Inc. Make sure that appropriate personnel are
familiar with these documents:
; This manual.
; The electrical schematic and connection diagram in the control
enclosure.
; The manuals for accessories and options you’ve selected.
; The customer parts list in the control enclosure.
6017 Series Hot Oil Large Temperature Control Units
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1-3 Models Covered
This manual lists installation, operation, and maintenance
instructions for the 6017 Series hot oil large temperature control
unit.
Model numbers are listed on the serial tag. A model number
followed by -Q indicates a specially constructed unit, and not all
information in this manual may apply. Make sure that you know
the model number, serial number, and operating voltage of your
unit if you contact Sterling, Inc.
1-4 Standard Features
• M2B microprocessor controller with fuzzy logic; includes
diagnostic features with indicator and warning status lights
• Non-fused lockable rotary disconnect
• Dual stage immersion heater with IEC contactors
• 550°F (288ºC) maximum operating temperature
• Branch fusing
• System status graphic display
• Pressure switch for low pump pressure shut-down
• NEMA 12 electrical enclosure
• UL listed subpanel
• To Process pressure gauge
• Independent safety thermostat
• Y strainer on From Process line
• A packed positive displacement pumps capable of reversing
to evacuate the process
• Easily removable panels for quick access to internal
components
• Audible alarm
Page 8
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
1-5 Available Options
• Drain valve
• Manual bypass
• Hour meter; measures total pump run time hours
• General fault visual alarm
• Automatic venting sequence
• Low level alarm for reservoir
• M2B microprocessor controller options include:
„ 4-20 mA remote set point and retransmission
„ SPI protocol, RS-485
„ General protocols, types RS-232, -485
„ Remote sensor
• Heat exchanger options of
• 3.9 sq. ft. (0.3627 sq. m)
• 6.7 sq. ft. (0.6231 sq. m)
• 13 sq. ft. (1.21 sq. m)
• 21 sq. ft. (1.96 sq.m)
• 27 sq. ft. (2.51 sq. m)
• Remote controller
• Lexan cover
• Mechanical Seal Pump
• Optional operating voltages of 208/3/60, 230/3/60, 575/3/60,
380/3/50, and 415/3/50
• Provisions for a Nitrogen Blanket on the Reservoir can
drastically increase fluid life.
1-6 Feature Descriptions
Immersion Heaters
The fluid is heated by the specially designed three-phase low watt
density electrical immersion heater, and regulated by the
controller. The standard heater has a steel sheath for low watt
density and good heat transfer.
These models can be supplied with 50, 60, 75, 100, 120, 150, and
200 kW low watt density immersion heaters, depending upon the
heating needs of the process. All models are built to provide full or
partial heat as required by the process and determined by the
controller, to provide more precise control.
6017 Series Hot Oil Large Temperature Control Units
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Heater Tank
The 6017 features a single pass heater tank. The tank is designed
to maintain an optimum balance of fluid velocity versus watt
density, and turbulence for excellent heat transfer, and minimal
pressure drop. The high fluid velocity will greatly prolong the life
of the heater and fluid.
Pump
The pump is a packed, positive displacement pump. It features a
nearly failure free design, and has proven itself after years of
dependable service. It is well suited for use with a variety of
commercially available heat transfer fluids. The pump has only
two internal moving parts, and a specially designed seal to give
years of trouble free service, even at high temperatures. The only
routine maintenance required is weekly greasing and occasional
packing and headspace adjustment; see Chapter 6 on Page 47 for
more information.
The pump is capable of running in either direction. Thus, the pump
reverse feature can be used to draw fluids back from the process. It
is not necessary to install a service air line to purge the lines before
changing molds. Since the pump is capable of achieving extremely
high pressures, it is necessary to regulate the pressure through use
of a regulating by-pass line (Fulflo valve). Because the pump is a
positive displacement pump, it will supply the process with rated
flow at or below the rated pressure.
The flow is constant until the pressure reaches the rated pressure.
The pressure however is a function of frictional losses through the
process that it is attached to. Systems with large process
connections, ports, and piping will operate at low pressures. While
systems with small process connections, ports, and piping will
operate at higher pressures. Once the pressure requirements exceed
the rated pressure, the fulflow valve will open and bypass the
necessary fluid to prevent high pressures.
Ful-Flo Valve
A regulating by-pass line featuring a Fulflo valve is standard in all
units. This is a safety device to prevent excessive pressure in the
event that the delivery line is obstructed. Each Fulflo is factory
preset to limit system pressure as specified by the customer. It
must not be tampered with in any way.
Page 10
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
In the event of an obstruction in the line, the Fulflo will open and
divert fluid from the delivery TO PROCESS line to the return
From Process line. A constant flow of fluid is maintained through
the heater tank to prevent damage to the heating elements and
fluid.
Cooling
Optional
The Sterlco-designed shell and tube heat exchanger is provided as
optional equipment in this unit. The design features U-tube
construction and copper-nickel tubes for durability and optimal
heat transfer.
The modular construction (unique to Sterlco units) allows the tube
bundle to be easily removed for periodic cleaning. Additionally,
check valves are installed on the water supply and drain lines to
prevent water from back flowing into the heat exchanger from a
closed drain or into the water supply piping.
The controller automatically regulates cooling by opening and
closing the cooling solenoid. This allows the proper amount of oil
to pass over the tubes of the heat exchanger. A water supply of 75
psi (517.1 kPa/5.2 bars) maximum is required for connection to the
heat exchanger.
Connection Lines
Connections for TO PROCESS and FROM PROCESS lines are:
• 2" NPT (50.8 mm) at 90 gpm (341 lpm)
• 2-1/2" NPT (63.5 mm) at 150 gpm (568 lpm)
• 3" NPT (76.2 mm) at 200 gpm (757 lpm)
Water connections for COOLING WATER SUPPLY and
COOLING WATER DRAIN are:
• ¾” NPT (19.1 mm) for 3.9 & 6.7 sq. ft. heat exchangers.
• 1" NPT (25.4 mm) for 13, 21, & 27 sq. ft. heat exchangers.
(See Chapter 3.) The customer is responsible for conversions to
metric standards.
6017 Series Hot Oil Large Temperature Control Units
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Sterling stocks many lengths of flexible metal hose; the part
number is 572-16969. State the length of hose you want when
ordering.
! WARNING
Component failure may result in high-temperature
oil spray, causing serious injury or death.
Make sure hoses, valves, and other components
installed in your process can withstand maximum
temperature and pressure of the 6017 unit; check
unit nameplate for specific capacities.
All components must be carefully inspected for
condition before installing. Make sure you have
factory components if you have any doubt.
Electrical System Controls
The electrical controls of your 6017 unit are specially engineered
for reliability, safety and simplicity of operation. The switches are
clearly labeled as to their function. Your 6017 unit has a system
status board so you can evaluate the status and performance of the
unit at a glance. Pilot lights are provided to indicate key unit
functions.
An audible alarm is standard with your unit. The alarm will sound
in the event of the following conditions:
• motor overload
• safety thermostat trip ( over temperature )
• low fluid pressure
• low fluid level (optional)
• high fluid level (optional)
Push the ALARM SILENCE button to silence the alarm. See
Chapter 4 for more information on control functions.
Page 12
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Panel and System Components
The pump motor and immersion heater operate on three-phase,
50/60 cycle, nominal voltage with the control circuit at 115 V
single phase. The control circuit voltage is provided by a single
phase machine tool transformer with primary fuse protection and a
grounded secondary. A main power disconnect is included as for
ease of service. The electrical panel is UL listed and complies with
NEC provisions.
All components are IEC rated for long life and reduced
maintenance. The heater elements are branch fused, and protected
from contactor welding by a separate primary voltage contactor.
The pump motor is controlled by a full voltage magnetic reversing
starter, with fused branch circuit overcurrent and thermal overload
protection. Many additional features are available as options.
A NEMA 12 enclosure is standard, with NEMA 4 available as an
option.
Air Purge
Upon initial start-up and mold/process change-out, you’ll need to
purge all air and water from the system. The 6017 unit has
appropriate valving to ensure complete purging. Procedures are
covered in Chapter 3.
! WARNING
Failure to purge the system of air before heating
may result in serious injury or critical system and
equipment damage.
Make sure you properly purge the system of air
before starting the heater cycle.
6017 Series Hot Oil Large Temperature Control Units
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressure Switch
A pressure switch is built into each unit to guard against heater
damage. This feature prevents the heater elements from being
energized unless the pump is running and fluid is in the system.
After a preset time, the pump shuts down if the fluid pressure is
not re-established. The pressure switch is preset at the factory; do
not tamper with it.
Safety Thermostat
The safety thermostat is mounted on the side of the heater tank.
This is to guard against the unlikely event of “runaway” heating. If
overheating does occur, the safety thermostat shuts down the
heater outputs and sounds an audible alarm. A red pilot light on the
status board also illuminates. The unit continues to pump fluid
through the system to prevent heater damage. Auxiliary factory
installed alarms such as beacons and klaxons are available as
options.
The safety thermostat is a manual reset type. All controller
functions are locked out until the red "STOP" button is pushed. It
is imperative that a qualified maintenance technician determine
and correct the cause of the fault before resuming operation.
Reservoir Tank
A reservoir tank with sight gauge is standard; usable capacity is
• 40 gallons (151 liters) on 6017L & 6017M units
• 65 gallons (246 liters) on 6017P & 6017V units.
The tank permits thermal expansion of the heat transfer fluid, and
provides make-up fluid.
Page 14
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
! WARNING
The reservoir tank may cause serious injury if it
ruptures from not being properly vented.
Make sure that the reservoir tank is always
properly vented to prevent tank rupture.
6017 Series Hot Oil Large Temperature Control Units
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1
6017 Series Hot Oil Large Temperature Control Unit.
The unit shown below is a 6017P Model.
6017 Series Temperature Control Unit Specifications
Model
Number
Heaters
Available capacities
Pump
Dimensions
Shipping
Weight♠
Available capacities
H
W
D
460 / 230 50 kW 100 kW 150 kW 200 kW 90 gpm 150 gpm 200 gpm
in.
cm in. cm in. cm
lbs.
Kg
9
9
9
9
9
9
9
9
9
9
9
9
9
n/a
9
6017-L
6017-M
6017-P
6017-V
n/a
n/a
9
n/a
n/a
9
n/a
n/a
9
62” 158 30” 76 60" 153 1,900 862
62” 158 30” 76 60” 153 1,900 862
62” 158 46” 117 60” 153 3,200 1,452
62” 158 46” 117 60” 153 3,200 1,452
9
9
9
9
♠ The actual shipping weights may vary based on options selected. The shipping weights listed are the maximum
shipping weights for standard units of the listed cabinet size.
Page 16
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Shipping Information
2-1 Unpacking and Inspection
You should inspect your Sterling/Sterlco 6017 Series hot oil large
temperature control unit for possible shipping damage. If the
container and packing materials are in re-usable condition, save
them for reshipment if necessary.
Thoroughly check the equipment for any damage that might have
occurred in transit, such as broken or loose wiring and
components, loose hardware and mounting screws, etc. In case of
breakage, damage, shortage, or incorrect shipment, refer to the
following sections.
2-2 In the Event of Shipping Damages
Important!
According to the contract terms and conditions of the Carrier,
the responsibility of the Shipper ends at the time and place of shipment.
; Notify the transportation company’s local agent if you discover
damage.
; Hold the damaged goods and packing material for the
examining agent’s inspection. Do not return any goods to
Sterling, Inc. before the transportation company inspection
and authorization.
; File a claim against the transportation company. Substantiate
the claim by referring to the agent’s report. A certified copy of
our invoice is available upon request. The original Bill of
Lading is attached to our original invoice. If the shipment was
prepaid, write us for a receipted transportation bill.
; Advise Sterling, Inc. regarding your wish for assistance and to
obtain an RGA (return goods authorization) number.
6017 Series Hot Oil Large Temperature Control Units
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3 If the Shipment is Not Complete
Check the packing list. The apparent shortage may be intentional.
Back-ordered items are noted on the packing list. You should have:
; 6017 Series hot oil large temperature control unit
; Bill of lading
; Packing list
; Operating and Installation packet
; Electrical schematic and panel layout drawings
; Component instruction manuals
Re-inspect the container and packing material to see if you missed
any smaller items during unpacking. Determine that the item was
not inadvertently taken from the area before you checked in the
shipment. Notify Sterling, Inc. immediately of the shortage.
2-4 If the Shipment is Not Correct
If the shipment is not what you ordered, contact the parts and
services department immediately at [262] 641-8610. Have item
and order numbers ready. Hold the items until you receive shipping
instructions.
2-5 Returns
Important!
Do not return any damaged or incorrect items
until you receive shipping instructions from Sterling, Inc.
Page 18
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installation
3-1 Work Rules
The installation, operation, and maintenance of this equipment
must be conducted in accordance with all applicable work and
safety codes for the installation location. This may include, but is
not limited to OSHA, NEC, CSA, and any other local, national,
and international regulations.
• Read and follow these instructions when installing,
operating, and maintaining this equipment. If the instructions
become damaged or unreadable, obtain additional copies
from Sterling/Sterlco.
• Only qualified personnel familiar with this equipment should
work on or with this hot oil temperature control unit.
• Work with approved tools and devices.
• Disconnect the electricity before maintenance or service.
If the unit is installed with a power cord that can be un-
plugged, unplug it. If the unit is permanently wired to a
power main, make sure that a fused power disconnect is
installed to allow the disconnect to be locked in the OFF
position. Open and lock out the disconnect installed in the
control enclosure.
3-2 Installation Requirements
Make sure that you meet the following requirements when
installing and operating your 6017 hot oil temperature control unit.
Installation Location Considerations
Locate the 6017 unit as close as possible to the process for proper
circulation and temperature control. Take care when selecting a
location. The area surrounding the unit must be free of obstructions
to ensure proper ventilation of internal components. Allow a
minimum clearance of at least 30 inches (76 cm).
6017 Series Hot Oil Large Temperature Control Units
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure that the unit location is not in a confined space to
ensure proper air circulation. Special air circulation/ventilation is
required for units operating at temperatures exceeding 500ºF
(260ºC). Vapors can escape from areas such as the reservoir tank
during high temperature operation.
! CAUTION
Harmful vapors may be generated from thermal fluid
during high temperature operation.
Prolonged or repeated exposure of these hot-generated
vapors may result in eye and respiratory tract irritation.
Avoid contact or inhaling harmful amounts of material.
Consult the Material Safety Data Sheet (MSDS) for
precautions and instructions for the thermal fluid you
are using.
Note: Before storing your 6017 temperature control unit, make
sure you remove all residual water with compressed air to
avoid a potential freezing hazard.
Note the following table of ambient temperature ranges permitted
for storage and operation:
Ambient storage range
Ambient operation range
ºF
ºC
ºF
ºC
-40ºF to 185ºF
-40ºC to 85ºC
-4ºF to 120ºF
-20ºC to 49ºC
You should preheat the process heat transfer fluid first if you want
to start the unit below an ambient temperature of 30ºF (-1ºC).
3-3 Connecting Piping
Make sure that all external piping is properly sized to reduce
external pressure drop as much as possible. Do not install process
or water supply/drain piping smaller than the fittings on the unit. If
the water supply piping is larger than unit fittings, reduce the pipe
size at the unit.
Page 20
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table lists 6017 TCU pipe sizes.
Connections for TO PROCESS and FROM PROCESS lines are:
• 2" NPT (50.8 mm) at 90 gpm (341 lpm)
• 2-1/2" NPT (63.5 mm) at 150 gpm (568 lpm)
• 3" NPT (76.2 mm) at 200 gpm (757 lpm)
Water connections for COOLING WATER SUPPLY and
COOLING WATER DRAIN are:
• ¾” NPT (19.1 mm) for 3.9 & 6.7 sq. ft. heat exchangers.
• 1" NPT (25.4 mm) for 13, 21, & 27 sq. ft. heat exchangers.
The customer is responsible for conversions to metric standards.
Notes: Always use a backup wrench to support 6017 unit piping
when making connections. Make sure all external piping is
supported independently of the 6017 unit.
Sterling, Inc. recommends that you have strainers installed
on the cooling water inlets and customer-supplied shut-off
valves on all piping connections. Use common black
welded pipe for permanent installations.
The 6017 is designed to operate with an open, unrestricted
drain line. Steam rapidly expands within the heat
exchanger, so any overpressure condition from
backpressure or standing columns of water against the
drain must be avoided.
If you must use a pipe joint compound, use a compound that can
withstand the high temperatures and pressures of your 6017 unit.
Always insulate all piping to prevent burn hazards and to retain
heat. Make sure insulation is properly rated for maximum
operating temperatures of your 6017 unit.
Piping Considerations for Mobile Installations
Because your 6017 unit is not fitted with casters, it should be
secured to the floor with the appropriate hardware. You can
purchase high-quality flexible metal hose from Sterling/Sterlco to
allow for thermal expansion of the process piping; state the length
you want when ordering.
6017 Series Hot Oil Large Temperature Control Units
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Process Piping
! CAUTION
• Hoses, valves and other components in your process must be able to
withstand the 6017 unit's maximum temperatures and pressures.
• Maximum temperatures and pressures are listed on the unit nameplate.
• Carefully inspect all components before installation.
• If in doubt about component suitability, obtain factory components.
• Fix all leaks! Fluid can be a potential fire and slip hazard.
• Never open pipe insulation that is smoking! Adding oxygen can cause a fire.
Connecting Cooling Water Piping
You must provide cooling water at 25 psi to 75 psi (172.4 kPa to
517.1 kPa/1.7 bars to 5.2 bars) for proper operation. Untreated
water can foul or corrode the heat transfer surfaces, slowing water
flow and causing fluid temperature control problems. Sterling, Inc.
sells a complete line of water treatment equipment that can reduce
downtime and maintenance costs.
Run properly-sized cooling water lines-never smaller than the
outlets on the 6017 unit. If external piping is larger than 6017 unit
connections, reduce the size of the piping at the unit.
Connecting Vent Piping
You must leave the vent connection open to the atmosphere at
all times. The vent connection is located on top of the reservoir.
On systems with piping above the reservoir level, you must run
vent piping to a minimum height of one foot (1’ / 31 cm) above the
highest point in the system. Run the piping down into an auxiliary
vented overflow chamber, such as a vented, covered 55-gallon
(208-liter) drum. This practice ensures that overflow will not
create a hazard to personnel.
Remember: All external piping must be supported independently
of the 6017 unit.
Page 22
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
! CAUTION
The reservoir tank must be vented to prevent pressurization.
A pressurized reservoir could rupture, allowing hot fluid
to escape and become a potential fire and slip hazard.
Note: Heat transfer fluids expand when heated. Expansion rates
vary, depending on fluid types and temperatures. For more
information on expansion rates, refer to specification
information for the heat transfer fluid you select.
Generally, most heat transfer fluids expand at the rate of
2.5% for every increase of 50°F from temperatures above
60°F (16°C).
Connect the TO PROCESS hookup to the entrance of the process
and the FROM PROCESS hookup to the exit of the process.
Connect the COOLING WATER SUPPLY to your plant water
supply. Connect the COOLING WATER DRAIN line to an open
drain, or to the return line of your central water system. If
returning to a central water system, use a condensate/return tank to
avoid a standing water column on the heat exchanger drain line.
! CAUTION
If you are routing the drain line to an open drain, make sure that
the line is directed away from personnel to avoid scalding.
Carefully select connecting lines and connectors between the 6017 unit
and the process to best meet the needs and requirements of your application.
Make sure lines and connectors have a service rating of
at least 100 psig (689.5 kPa/6.9 bars), and a temperature rating
at least equal to the maximum operating temperature of your 6017 unit.
6017 Series Hot Oil Large Temperature Control Units
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3
Typical Flow Schematic
Note: The heat exchanger is optional, and the "Vent Valve" is also known as the "Blow-Off
Valve."
• Vent Valve - open for purge/closed for run/open for pump reverse.
• Return Valve - closed for purge/ open for run/ closed for pump reverse.
• Reservoir Tank - Open to atmosphere at all times, unless nitrogen blanket provisions are
present.
Page 24
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4
Custom Process Piping
The optimum location for venting is on the top of the overhead return piping above the unit. The
customer is encouraged to add an extra vent (Blow-Off) valve at this point. With this new Blow-
Off Valve location the return valve and internal blow-off valve should be closed completely
during venting. Otherwise air could be pulled into the piping by gravity instead of being
removed.
The frequent process disconnection scenario has the vent line connected to the process side of
the two isolation valves. This allows the disconnected process to be vented without
contaminating the rest of the piping and unit to be contaminated with air. This is accomplished
by the following steps once the process is reconnected to the unit and the isolation valves are still
closed.
Note: during this process the internal blow-off valve is closed and the return valve can be open.
1.) Open the external vent valve.
2.) Open the isolation valve that is delivering oil to the process from the unit. Leave the
isolation valve that is returning the oil from the process to the unit closed.
3.) Wait for all of the process to fill with heat transfer fluid and push the air and back to the
reservoir.
4.) Once all of the air has been replaced with fluid, and only oil is being dumped into the
reservoir; close the vent valve.
5.) Open the isolation valve that is returning the oil from the process.
6017 Series Hot Oil Large Temperature Control Units
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4 Making Electrical Connections
These units are designed for three-phase voltage operation. Refer
to the unit nameplate for proper voltage and amperage
requirements, and make sure your electrical service conforms.
Check the unit nameplate for correct voltage and amperage
before making electrical connections!
! CAUTION
1. Provide a correctly sized and protected power supply to the unit.
2. If an electrical supply disconnect is not installed as a factory option, the
customer is responsible to properly size and install a suitable disconnect.
3. Refer to National Electric Code (NEC) 430-24-26 for proper feed conductor
and supply disconnect sizing.
4. Voltages must be within plus or minus ten percent (±10%) of the nameplate
rating.
5. Maintain a safe ground and disconnect the power supply before servicing
the unit.
A qualified electrician should make electrical connections and disconnect the
electricity when service calls are needed.
• Locate disconnects in an easily accessible location.
Operators should not have to squeeze around the 6017 unit to
reach disconnects, especially in case of emergency.
• When running conduit whips to the 6017 unit, make sure that
whips are routed away from hot piping.
Page 26
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Check the unit nameplate for correct voltage and amperage
before making electrical connections!
! DANGER
IMPROPER ELECTRICAL
CONNECTIONS CAN DAMAGE THE
UNIT AND CAUSE SERIOUS
OPERATOR INJURY OR DEATH!
MAKE SURE THAT ALL
ELECTRICAL CONNECTIONS ARE
MADE BY A QUALIFIED
ELECTRICIAN, AND THAT ALL
CONNECTIONS ARE TIGHT.
Make all electrical supply connections at the front of the unit. An
access panel covers all electrical connections. Run electrical
connections to the supply terminals from either side of the unit.
Make sure that all three phases are wired correctly. The pump runs
backwards if not wired properly.
6017 Series Hot Oil Large Temperature Control Units
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
- Notes -
Page 28
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Startup Preparations
4-1 Starting the Unit
UNIT START-UP (WITH MANUAL BLOW-OFF VALVE)
The highly engineered controls and controller make this unit almost self operating. Before you
can begin heating, it will be necessary to perform the following start up procedures. This will
ensure that all air is vented from the system to prevent fluid degradation and damage to the
heater.
1. Open the Return Valve and the Blow-Off Valve. Make sure the drain valves are
closed and plugged.
2. Add fluid to the reservoir tank until the level is near the top of the sight glass.
3. Close the Return Valve inside the unit.
4. Depress the "Pump Start" button to start the pump. Check motor rotation by
observing the pressure gauge. If the gauge indicates positive pressure, rotation is
correct. If not, disconnect power and reverse the incoming power leads.
5. As fluid is drawn out of the reservoir tank to fill the process, the fluid level will fall in
the tank. Continue to add fluid to maintain the level about 4 inches from the bottom
of the sight glass.
! CAUTION
You must purge the system of air before the heating cycle.
Personal injury and system damage can occur from a pressurized system.
6. Air and Oil will be vented through the Blow-Off Valve and into the reservoir tank.
7. After the unit stops requiring more oil and has at least 5 psi of pressure, open the
Return Valve half way.
8. Once the unit has stopped requiring more oil again and has at least 10 psi of pressure,
select a set point of 100°F (38°C) and switch unit into the "Auto" mode. As the oil
warms up, viscosity will decrease, and the pressure will fall.
9. In 2-minute intervals increase the setpoint to 150°F (66°C) and 200°F (93°C).
6017 Series Hot Oil Large Temperature Control Units
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
10. If any water is present in the system, it must be boiled off before continuing
operation. Select a setpoint of 215°F (102ºC) and observe the reservoir tank vent for
any signs of escaping steam. Continue to run at 215ºF (102ºC) until no more steam
appears and pressure has stabilized.
11. When fluid level has stabilized and air and water are purged from the system, open
the Return Valve all the way. And select a setpoint of 250°F (121°C).
12. If the fluid level and pressure remain stable close the Blow-Off Valve. Do not open
the Blow-Off Valve above 250°F.
With the system properly purged, only 4 - 6" of fluid should be visible in the sight glass. This
will allow for expansion of the fluid as it heats, as well as capacity for process fluid when the
pump is reversed and fluid withdrawn from the mold.
The 6017 is now ready for use. All that is required is to select a process set point on the
controller as described in the controller manual.
NOTE: If all traces of water are not removed from the system, severe cavitation may occur at
elevated temperatures. Indications are a “gravely” sounding pump, fluctuating or dropping
pressure, or rapidly rising fluid level in the expansion tank. Repeat Steps #9-12 if this occurs.
UNIT START-UP (WITH AUTOVENT SOLENOID)
The highly engineered controls and controller make this unit almost self operating. Before you
can begin heating, it will be necessary to perform the following start up procedures. This will
ensure that all air is vented from the system to prevent fluid degradation and damage to the
heater. The autovent solenoid operates just like the manual Blow-Off valve, however it opens
electrically and for only a specified time. The benefit is that it vents every time the unit is started
and it will automatically shut off after a predetermined amount of time. It is also convenient,
because the vent button is located on the front of the unit. It has the added safety of being
automatically prevented from opening above 250°F by a safety thermostat.
1. Open the Return Valve. Make sure the drain valves are closed and plugged.
2. Add fluid to the reservoir tank until the level is near the top of the sight glass.
3. Depress the "Pump Start" button to start the pump. Check motor rotation by
observing the pressure gauge. If the gauge indicates positive pressure, rotation is
correct. If not, disconnect power and reverse the incoming power leads.
4. Close the Return Valve inside the unit.
5. As fluid is drawn out of the reservoir tank to fill the process, the fluid level will fall in
the tank. Continue to add fluid to maintain the level about 4 inches from the bottom
of the sight glass.
Page 30
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
! CAUTION
You must purge the system of air before the heating cycle.
Personal injury and system damage can occur from a pressurized system.
6. Air and Oil will be vented through the automatic Blow-Off Valve and into the
reservoir tank.
7. After the unit stops requiring more oil and has at least 5 psi of pressure, open the
Return Valve half way. If the Blow-Off cycle times out, start the sequence again.
The timer is factory set at 5 minutes. A longer time can be set if required. The first
time the unit is filled with oil it takes some time to vent out the air. You should
determine how long is appropriate for venting on a regular basis when the unit is
already full.
8. Once the unit has stopped requiring more oil again and has at least 10 psi of pressure,
select a set point of 100°F (38°C) and switch unit into the "Auto" mode. As the oil
warms up, viscosity will decrease, and the pressure will fall.
9. In 2-minute intervals increase the setpoint to 150°F (66°C) and 200°F (93°C).
10. If any water is present in the system, it must be boiled off before continuing
operation. Select a setpoint of 215°F (102ºC) and observe the reservoir tank vent for
any signs of escaping steam. Continue to run at 215ºF (102ºC) until no more steam
appears and pressure has stabilized. Restart the Blow Off cycle as necessary if it
times out.
11. When fluid level has stabilized and air and water are purged from the system, open
the Return Valve all the way. And select a setpoint of 250°F (121°C). Restart the
Blow Off cycle as necessary if it times out.
12. If the fluid level and pressure remain stable allow the Blow-Off Valve to close. The
vent valve will not open the Blow-Off above 250°F.
With the system properly purged, only 4 - 6" of fluid should be visible in the sight glass. This
will allow for expansion of the fluid as it heats, as well as capacity for process fluid when the
pump is reversed and fluid withdrawn from the mold.
The 6017 is now ready for use. All that is required is to select a process set point on the
controller as described in the controller manual.
NOTE: If all traces of water are not removed from the system, severe cavitation may occur at
elevated temperatures. Indications are a “gravely” sounding pump, fluctuating or dropping
pressure, or rapidly rising fluid level in the expansion tank. Repeat Steps #9-12 if this
occurs.
6017 Series Hot Oil Large Temperature Control Units
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2 Shutting Down the Unit
UNIT SHUT DOWN (WITH AUTOVENT SOLENOID OR MANUAL VENT VALVE)
Cool the unit down by switching the Mode switch to the "Manual Cool" position. This will
disable the heaters ( i.e. prevent the controller from turning them on) and open the cool solenoid.
Fluid temperature can be monitored on the controller display during cool down. When fluid
temperature is below 120ºF, depress the PUMP STOP button to turn the unit off.
4-3 Returning Fluid to the Tank
RETURNING FLUID TO TANK
If the unit is to be moved from one process to another (i.e. mold changes, etc.), the following
steps must be taken to drain the mold and process lines. Note that this is just the opposite of unit
start up/air purge:
1. Cool fluid to 150°F (66°C) maximum.
2. Depress the PUMP STOP push button.
3. Close the Return Valve.
4. Open the Blow Off Valve. (with autovent, the valve will open on its own)
5. Depress and hold the PUMP REVERSE push-button. The pump will then run in
reverse, drawing fluid from the mold and lines, and into the reservoir tank.
6. Watch the sight glass to prevent overflow of the reservoir tank.
! CAUTION
The reservoir tank may not have adequate volume
to contain the total system capacity of fluid.
An overflowing reservoir allows hot fluid to escape
and become a potential fire and slip hazard.
The total capacity of the tank can be found on page 14.
If it appears that the tank may overfill, connect a line from the FILL port of the reservoir tank to
a clean auxiliary container.
Page 32
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
- Notes -
6017 Series Hot Oil Large Temperature Control Units
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Using Controls and Indicators
5-1 The Microprocessor Controller
The M2B controller is an easy-to-operate microprocessor-based
PID control device. When the process reaches the set point, the
PID control cycles the cooling valve and/or immersion heater to
maintain the proper leaving fluid temperature.
The controller is fully factory tested. Set the process temperature
set point you want and the controller does the rest.
Built-in range of operation on the controller is 0°F to 550°F (-18ºC
to 288ºC).
Figure 4
Typical M2B Graphic and Button Control Panel
R
STATUS
RUN
DISPLAY
TO PROCESS
185
185
PROCESS
HI HEAT
LO HEAT
COOL
FROM PROCESS
T
SET POINT
FLOW
FLUID
SAFETY
HI/LO
PROBE
MOTOR
PRESSURE THERMO
ALARM
FAIL
FAIL
UP
DOWN
ENTER
SET POINT
INDEX
HI
ALARM
LO
ALARM
DISPLAY
STERLING, INC.
MILWAUKEE, WI
TEMPERATURE CONTROL SYSTEM -- M2B
Page 34
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2 Identifying M2B Controller Panel Components
Screen Displays
SET POINT Numeric LED
During normal operation, the SET POINT LED on the controller
displays the process set point you want the unit to maintain. It also
displays parameter and pre-set function values during setup.
PROCESS Numeric LED
During normal operation, the PROCESS LED on the controller
displays the actual process temperature at the To Process
thermocouple. It also lists parameter symbols during setup and
error messages if an error occurs.
Status Indicators
RUN Indicator
The RUN indicator is on during normal operation and flashes
during the auto-tuning sequence.
HI HEAT Indicator
The HI HEAT indicator is on when fluid heaters are at 100%
capacity to rapidly raise fluid temperature.
LO HEAT Indicator
The LO HEAT indicator is on when fluid heaters are at 50 percent
capacity.
COOL Indicator
The COOL indicator is on when fluid temperature is above the set
point and is being cooled.
Display Indicators
TO PROCESS Indicator
The TO PROCESS indicator is on when the PROCESS LED
screen on the controller displays the temperature of the outgoing
fluid.
6017 Series Hot Oil Large Temperature Control Units
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
FROM PROCESS Indicator
UT Indicator
The FROM PROCESS indicator is on when the PROCESS LED
screen on the controller displays the temperature of the incoming
fluid.
The UT indicator is on when the PROCESS LED screen on the
controller displays the difference in temperature between outgoing
Delivery fluid and incoming Return fluid.
FLOW Indicator
The FLOW indicator is on when the PROCESS LED screen on the
controller displays the flow of fluid in liters per minute; this
function requires the optional flow sensor.
Alarm Indicators
FLUID PRESSURE Indicator
The FLUID PRESSURE indicator goes on when fluid pressure is
low. The TCU shuts down and resumes operation only when a
proper level of fluid pressure is restored.
SAFETY THERMO Indicator
The SAFETY THERMO indicator is on when an over-temperature
condition occurs. The heater outputs are then disabled, the pump
continues to operate, and the COOL solenoid energizes. This is a
fatal fault condition, requiring that main power be disconnected
to reset the M2B controller.
HI/LO ALARM Indicator
PROBE FAIL Indicator
The HI/LO ALARM indicator is on when an individually-set alarm
condition occurs. The HI deviation is +200ºF (about +93ºC) above
the set point. The LO deviation is -100ºF (about -37ºC) below the
set point. Alarms reset automatically.
The PROBE FAIL indicator is on when a temperature sensing
probe fails. A delivery probe failure displays DEL on the screen,
and a return probe failure displays RET on the screen. The alarm
resets after the failed probe is replaced.
Page 36
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTOR FAIL Indicator
The MOTOR FAIL indicator is on during improper pump rotation,
motor out of phase, or thermal motor overload conditions. This is a
fatal fault condition, requiring that main power be disconnected
to reset the M2B controller.
5-3 Using M2B Controller Keys
SET POINT
SET POINT Key
UP
SET POINT
Press and hold the
SET POINT key, then press the
DOWN
UP Arrow key to increase the set point value or press the
DOWN Arrow key to decrease the set point value displayed on the
SET POINT LED screen.
UP
UP Arrow Key
UP
Press the
UP Arrow key to increment or advance the
values or settings on the LED screens.
DOWN
DOWN Arrow Key
DOWN
Press the
DOWN Arrow key to decrement or reduce the
values or settings on the LED screens.
Important!
Do not change any of the control settings
without consulting the Sterling/Sterlco Service Department.
The Sterling, Inc. warranty does not cover TCU failures
from tampering with controller settings!
6017 Series Hot Oil Large Temperature Control Units
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
ENTER
ENTER Key
INDEX Key
ENTER
INDEX
The
ENTER key is used with the
INDEX key menu
to store the value or the item that was changed. If this key is not
pressed, the previously-stored value or item is retained.
INDEX
INDEX
Each press of the
INDEX key advances the screen to the
next menu item. Refer to your Sterling/Sterlco M2B Temperature
Control Owner’s Manual for a list of functions available using this
key.
HI
ALARM
HI ALARM Key
UP
HI
ALARM
Press and hold the
HI ALARM key, then press the
UP Arrow key to increase the alarm high limit value or press the
DOWN
DOWN Arrow key to decrease the alarm high limit value
on the SET POINT LED screen. Refer to your Sterling/Sterlco
M2B Temperature Control Owner’s Manual for a list of functions
available using this key.
LO
ALARM
LO ALARM Key
UP
LO
ALARM
Press and hold the
LO ALARM key, then press the
UP Arrow key to increase the alarm low limit value or press the
DOWN
DOWN Arrow key to decrease the alarm low limit value on
the SET POINT LED screen. Refer to your Sterling/Sterlco M2B
Temperature Control Owner’s Manual for a list of functions
available using this key.
Page 38
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY
DISPLAY Key
DISPLAY
Press the
DISPLAY key to advance through the display
menu. Each key press increments to the next available function.
The screen returns to delivery temperature after thirty (30) seconds
of inactivity. Refer to your Sterling/Sterlco M2B Temperature
Control Owner’s Manual for a list of menus available using this
key.
Digital Flow Screen
Optional
The optional digital flow screen displays process flow in gallons
per minute (gpm). No customer-usable control is necessary.
Depending on option level and setup, flows can be measured at
rates reaching and exceeding 75 gallons per minute (284 lpm).
5-4 Identifying Control Panel Switches
This section lists the descriptions and functions of the control
panel switches. These switches control the operation of the unit.
Figure 5
Control Panel Switches
PUMP
ALARM
START
SILENCE
PUMP START
PUMP STOP
ALARM SILENCE
AUDIBLE ALARM
STOP
REVERSE
PUMP REVERSE
MODE SELECT
MODE
AUTO
OFF
MAN. COOL
6017 Series Hot Oil Large Temperature Control Units
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Start
Pump Stop
Press the START
direction.
button to start the pump in the normal forward
Press the STOP button to stop the pump and de-energize the
controller.
! CAUTION
Always press the Pump Stop button and allow the
pump to come to a complete stop before pressing the
Pump Reverse button.
Failure to let the pump stop before reversing may
damage the pump and drive.
Pump Reverse
Press the REVERSE
button to start the pump in the reverse
direction. Use this feature to purge oil from the mold.
Vent Cycle Start (optional)
Press the VENT
button to start the vent cycle timer. Use this
feature to purge air and water from the unit and process. This is
used when the Autovent Cycle Option is added to the unit.
Mode Select
With the pump running, you can select the AUTO position or the
MAN. COOL (manual cooling) position with the Mode Select
switch. Select AUTO mode to energize the controller, permitting it
to monitor and control the process. The switch automatically
returns to the OFF position when in AUTO mode. The switch stays
in the MAN. COOL position in Manual Cooling mode.
! CAUTION
Always let the pump run for at least one (1) minute
before switching to AUTO mode.
Never switch to AUTO mode when filling or venting the
unit, except as described in the Unit Startup chapter.
Improper switching can seriously damage the heater,
as it could become energized with air in the system.
Page 40
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Silence
Press the ALARM SILENCE
button to silence the audible alarm
on the console.
! CAUTION
After you silence the alarm, make sure you locate and
correct the alarm condition before continuing with unit
operation.
5-5 Identifying System Status Board Indicators
The system status board is located next to the controller panel. It
displays indicator lights to show current operation status, letting
you analyze system performance.
Figure 6
System Status Board Indicators
SYSTEM STATUS
PUMP OVERLOAD
PUMP REVERSE
PUMP FORWARD
MODE
POWER ON
AUTO
BYPASS
RELIEF VALVE
HEATER
LOW
DELIVERY
PRESSURE
SAFETY
THERMO
ON
HEAT
STRAINER
EXCHANGER
VENT
FILL
HIGH
LEVEL
RETURN
DRAIN
COOL
SOLENOID
LOW
LEVEL
VENT
SOLENOID
RES.
TANK
6017 Series Hot Oil Large Temperature Control Units
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the status board to optimize unit performance. For example, if
you observe a rapid cycling of the Heater and Cool Solenoid
indicators, the unit is operating with a process inefficiency; see the
Troubleshooting chapter for more information.
What follows is a description of system status board indicators.
Status Indicator Lights
Pump Reverse Indicator Light
The Pump Reverse indicator light illuminates when the unit pump
runs in reverse.
Pump Forward Indicator Light
The Pump Forward indicator light illuminates when the unit
pump runs in the normal forward direction. This indicator typically
illuminates continuously during normal operation.
Heater On Indicator Light
The Heater On indicator illuminates when the heater energizes.
This indicator illuminates intermittently when the controller
energizes and de-energizes the heater as the heating cycle requires.
Cool Solenoid Indicator Light
The Cool Solenoid indicator illuminates when the cooling
solenoid energizes. This indicator illuminates intermittently as the
controller energizes the cooling solenoid; it is used only on the
optional heat exchanger.
Vent Solenoid Indicator Light
If the Autovent option is present. The Vent Solenoid indicator
illuminates when the venting solenoid energizes during venting
sequences.
Mode Indicator Lights
Select the unit operating mode by using the selection switch.
Power On Mode Indicator Light
The Power On mode indicator light illuminates to indicate that the
control circuit is energized in the unit.
Page 42
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Mode Indicator Light
The Auto mode indicator light indicates that the Auto mode is
active and the controller is monitoring the system and controlling
the process.
If the Auto light is off and the Cool Solenoid indicator light is
illuminated, the controller is disabled and the cooling solenoid is
open, permitting maximum cooling.
If the Auto and Cool Solenoid indicator lights are off, the unit is
in standby.
Fault Indicator Lights
Pump Overload Indicator Light
The Pump Overload indicator light illuminates when the pump is
overloaded. This is an alarm condition, so the audible alarm
activates to notify you of the pump overload fault, and the unit
shuts down.
Always correct the alarm condition before returning to normal
operation!
Low Pressure Indicator Light
The Low Pressure indicator light illuminates when the unit has
low heat transfer fluid pressure. This is an alarm condition, so the
audible alarm activates to notify you of the low pressure fault, and
disables controller outputs, permitting the pump to continue to
circulate fluid to avoid damage. If low pressure continues past five
minutes elapsed time, the pump shuts off.
Always correct the alarm condition before returning to normal
operation!
Safety Thermo Indicator Light
The Safety Thermo indicator light illuminates when the unit is
overheating. This is an alarm condition, so the audible alarm
activates to notify you of the safety thermo fault, and disables
controller outputs, permitting the pump to continue to circulate
fluid to avoid damage.
6017 Series Hot Oil Large Temperature Control Units
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Always correct this alarm condition before returning to
normal operation!
High Level Indicator Light
The high fluid level alarm is an available option. The High Level
indicator light illuminates when the heat transfer fluid level in the
reservoir tank is too high. Carefully remove just enough fluid so
this indicator light shuts off and an adequate volume is maintained
in the reservoir.
Low Level Indicator Light
The low fluid level alarm is an available option .The Low Level
indicator light illuminates when the heat transfer fluid level in the
system is too low. This is an alarm condition, so the audible alarm
activates to notify you of the low fluid level fault, and the
controller outputs are disabled.
Always correct the alarm condition before returning to normal
operation!
Page 44
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
- Notes -
6017 Series Hot Oil Large Temperature Control Units
Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Preventive Maintenance
! WARNING
Make sure that your maintenance
technicians comply with lock-out/tag-out
procedures during any servicing or
maintenance of this unit and related
equipment, per OSHA article ART 1910.147.
Before you begin servicing this unit,
disconnect all power to the unit, let the unit
cool down completely, and turn off the
water.
Failure to follow these directives can result
in serious injury or death!
6-1 Periodic Checks
Making Daily Checks
• Check fluid level; add fluid as needed.
• Check all connecting lines, hoses, and connectors for wear or
damage.
Making Monthly Checks
• Check for leaks developing at the pump seal, gaskets, and
other similar locations.
• Check the pump drive V belt for any wear.
• Check the reservoir tank vent for any obstructions.
Page 46
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Quarterly Checks
• Check the heat transfer fluid for deterioration. If the fluid is
noticeably darker, or it seems significantly thicker, drain the
system and replace the fluid with fresh, new recommended
heat transfer fluid.
Do a routine check of the fluid every 1,000 hours of
operation or every three (3) months, whichever comes first.
Contact Sterling, Inc. Service for information on fluid
testing.
Making Six-Month Checks
• Inspect electrical connections for secure, tight attachment
points and ground connections. Inspect the power cable,
especially at the entrance point to the electrical enclosure.
Have a qualified electrician perform this inspection.
• Check the mounting bolts on the pump, the motor, and the
heater flange for tightness.
• Remove the heat exchanger tube bundle and check it for lime
and mineral deposits. Carefully clean the bundle as needed.
6-2 Routine Servicing
Your hot oil temperature control unit requires little in preventive
maintenance and servicing. To keep it in good, reliable working
order, make sure you follow the following scheduled preventive
maintenance procedures.
Keep surfaces clean and free of any excessive accumulations of
dirt, oil, or debris. This is especially true for the pump. It relies on
free air circulation for proper cooling.
Check the motor air intake screen for any accumulation of dirt;
clean it as needed.
6017 Series Hot Oil Large Temperature Control Units
Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Servicing the Unit Monthly or Every 500 Hours
• Lubricate the pump at the grease fittings with a high-
quality polyurea grease rated at 320ºF or higher.
Recommended: Chevron Black Pearl; do not over-lubricate.
• Adjust the pump drive belt tension. Use the belt tensioning
specifications listed in this chapter on Page 51. Make sure
that the motor pulley is properly aligned with the pump
pulley; use a straightedge to check. Tighten motor mounting
bolts after realignment.
• Inspect the screen in the Y strainer for accumulations of
debris. Clean as needed.
Servicing the Unit Every Three Months
Remove and clean the screen in the Y-strainer. Replace the screen
if it is damaged.
Page 48
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Lubrication Procedure
Be sure that the grease you are adding to the motor is compatible with the grease already in the
motor. Consult your Baldor distributor or an authorized service center if a grease other than the
recommended type is to be used.
A high grade ball or roller bearing grease should be used. Recommended grease for standard
service conditions is Polyrex EM (Exxon Mobil).
Equivalent and compatible greases include:
Texaco Polystar, Rykon Premium #2, Pennzoil Pen 2 Lube and Chevron SRI.
1800 RPM
motor size
Lubrication Intervals in Hours
up to 250°F 251°F - 400°F over 400°F ounces grams cu. In.
Grease to be added
5 HP and Under
7-1/2 to 20 HP
25 - 40 HP
12,000
10,000
8,000
6,000
5,000
4,000
1,200
1,000
750
0.30
0.61
0.81
8.4
17.0
23.0
0.6
1.2
1.5
Caution: To avoid damage to motor bearings, grease must be kept free of dirt. For an
extremely dirty environment, contact your Baldor distributor or an authorized Baldor Service
Center for additional information.
With Grease Outlet Plug
1. Clean all grease fittings.
2. Remove grease outlet plug.
3. If motor is stopped, add the recommended amount of grease. If motor is to be greased
while running, a slightly greater quantity of grease will have to be added. Add grease
slowly until new grease appears at shaft hole in the endplate or purge outlet plug.
4. Re-install grease outlet plug.
Without Grease Outlet Plug
1. Disassemble motor.
2. Add recommended amount of grease to bearing and bearing cavity. (Bearing should be
about 1/3 full of grease and outboard bearing cavity should be about 1/2 full of grease.)
Note: Bearing is 1/3 full when only one side of bearing is completely full of grease.
3. Assemble motor.
6017 Series Hot Oil Large Temperature Control Units
Page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3
Draining the Unit for Storage
You should thoroughly flush and drain the 6017 unit if you need to
take it out of service for a long time, or if you expect it to become
exposed to freezing temperatures. Sterling, Inc. recommends
SterlFlush™ flushing fluid or equivalent for flushing your 6017
unit; follow unit flushing instructions that comes with SterlFlush™
flushing fluid.
Drain plugs are provided at the base of the heater tank, reservoir
tank, and on the pump. You should also remove, drain, and
reinstall the heat exchanger tube bundle before storage.
6-4 Corrective Maintenance
Pumps and Seals
Each 6017 unit is completely tested and calibrated before leaving
the factory. The unit is then cooled, drained, and packed for
shipment.
If the unit stands idle for a long time before being installed in your
factory, gaskets can dry out and possibly leak when you start the
unit. In most cases, these gaskets soon swell and form a tight seal.
If not, you may need to tighten the bolts to stop the leak.
Similarly, rough handling in shipping may sometimes cause minor
leaks upon startup; you may need to re-tighten bolts or fittings
to stop the leak.
You should expect to periodically adjust the packing or replace the
pump seal. If the pump is properly lubricated and used at moderate
temperatures, the seal should last several years. The following
section describes the proper procedures for replacing the seal
Periodic replacement of the pump drive V-belt is also to be
expected.
Note: If the pump motor wiring is disconnected for removal from
the unit, you must check the actual direction of rotation
when the motor is rewired to the unit.
Page 50
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
6017 Series Hot Oil Large Temperature Control Units
Page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Troubleshooting
Condition
Possible cause
Solution
Increase size of connectors/
water lines.
Undersized connectors/lines.
Long connecting lines between
unit and mold.
Move the unit closer to the mold
and shorten connecting lines.
Connect lines for parallel flow
instead of series flow.
Check mold for metal chips or
deposits. Clean mold.
Remove and replace fitting or
valve.
Serpentine flow through mold.
Blocked line in mold.
Temperature fluctuations/rapid
cycling from hot to cold.
Quick disconnect fitting with
check valve.
Carbon build-up in unit piping or Clean or replace affected piping.
fittings.
Replace fluid.
Check unit by opening the
manual bypass to determine if
the TCU contols the set point
temperature.
Faulty Sterlco TCU.
Switch Return and Delivery
probes.
Reversed probes.
Check all lines/connections/
fittings.
Loss of fluid in process.
Allow vent timer to run out; or,
check valve operation when unit
is cold by opening the fill port.
Switch to Manual Cool mode
several times to flush valve. If
Vent valve open.
Unit does not heat properly/can
not achieve set point.
Faulty/dirty solenoid valve;
usually detected when there is a the leak continues, disconnect
steady stream or trickle of water the power to the unit, turn off the
out of the drain line.
water supply, and clean or
replace the solenoid.
Degraded fluid.
Drain and replace fluid.
Visual inspection of coil and
contacts. Repair/replace
defective contactors.
Defective heater contactor.
Check resistance on all three (3)
legs of heater with an
Defective immersion heater.
Heater burnout.
ohmmeter. If not all equal,
contact factory for replacement
heater.
Check heater tank for scorched/
discolored paint. Check
resistance on all three (3) legs
of heater with an ohmmeter.
Replace heater as needed.
Unit does not heat.
Page 52
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Condition
Possible cause
Controller heater output open.
Clogged Y strainer.
Solution
Check the heater output with an
ohmmeter to ground. It should
read in the mega-ohm range.
Infinite or zero readings indicate
a defective output.
Unit does not heat.
(cont’d.)
Clean Y strainer.
Water supply to unit is turned
OFF.
Open water supply.
Water drain is plugged or
excessive back pressure in
drain line.
Heat exchanger tubes plugged
by lime deposits.
Clear drain line or eliminate
back pressure condition.
Unit overheats/unable to cool.
Remove tube bundles; clean/
replace as required.
Test solenoid valve by switching
to Manual Cool mode and listen
for valve operation. Replace if
faulty.
Faulty solenoid valve.
Inspect/replace faulty line or
connection.
Perform venting sequence in
Chapter 3.
Leaks in connecting lines.
Air in circulating lines.
Check fluid level in sight glass.
Add fluid if required.
Low fluid.
Defective Ful-Flo valve.
See Chapter 3.
Drain water from low point in
piping (see Chapter 3), or boil
water off.
Water in fluid.
Rapid drop in pressure/no
pressure.
Allow vent timer to run out; or,
check valve operation when unit
is cold by opening the fill port.
Check motor; rewire if
necessary. See electrical
diagrams.
Vent solenoid open.
Pump running in reverse.
Pump repair/adjustment
needed.
V belt broken/worn.
Adjust head spacing or replace
worn pump components.
Replace as required.
Drain water from low point in
piping (see Chapter 3), or boil
water off.
Water in fluid.
Noisy pump.
Drain and flush system. Replace
fluid.
Severely degraded fluid.
6017 Series Hot Oil Large Temperature Control Units
Page 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Notes
Page 54
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Notes
6017 Series Hot Oil Large Temperature Control Units
Page 55
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Notes
Page 56
6017 Series Hot Oil Large Temperature Control Units
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Assistance
Parts Department
[800]
Call toll-free 7am–5pm CST or call
423-3183, [262] 641-8610, or fax to [262] 641-8653
The ACS Customer Service Group will provide your company with genuine OEM quality parts
manufactured to engineering design specifications, which will maximize your equipment’s performance
and efficiency. To assist in expediting your phone or fax order, please have the model and serial
number of your unit when you contact us. A customer replacement parts list is included in this manual
for your convenience. ACS welcomes inquiries on all your parts needs and is dedicated to providing
excellent customer service.
Service Department
[
]
[262]
Call toll-free 8am–5pm CST 800 423-3183 or call 641-8610
[
]
Emergencies after 5pm CST, call 847 439-5655
We have a qualified service department ready to help. Service contracts are available for most products.
Sales Department
[262]
Call
641-8610 Monday–Friday, 8am–5pm CST, fax [262] 641-8653
Our products are sold by a world-wide network of independent sales representatives. Contact our Sales
Department for the name of the sales representative nearest you.
Contract Department
[262]
Call
641-8610 Monday–Friday, 8am–5pm CST
Let us install your system. The Contract Department offers any or all of these services: project planning;
system packages including drawings; equipment, labor, and construction materials; and union or non-
union installations.
Sterling, Inc.
2900 S. 160th Street
New Berlin, WI 53151
6017 Series Hot Oil Large Temperature Control Units
Page 57
Download from Www.Somanuals.com. All Manuals Search And Download.
|