DOT MATRIX PRINTER
DP8340RC SERIES
[PARALLEL INTERFACE]
USERS MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. OUTLINE .............................................................................................. 1
2. UNPACKING AND INSTALLATION ................................................ 2
2-1. Unpacking .................................................................................... 2
2-2. Installation of Paper Holders and Re-Roll
Prevention Guard ......................................................................... 3
2-3. Handling Notes.............................................................................4
3. PART IDENTIFICATION AND NOMENCLATURE ........................ 5
3-1. Power Supply Unit ....................................................................... 5
3-2. Printer ........................................................................................... 6
3-3. Part Functional Description.......................................................... 7
4. INSTALLATION OF INK RIBBON AND PAPER.............................8
4-1. Installation of Ink Ribbon ............................................................ 8
4-2. Removal of Ink Ribbon ................................................................9
4-3. Paper Insertion ...........................................................................10
4-3-1. For Roll Paper .................................................................10
4-3-2. Roll Paper Installation
(When using the optional Printer Cover 8340R).............11
4-3-3. Validation Option Installation .........................................12
4-4. Roll Paper Removal ................................................................... 12
5. CONTROL CODES ............................................................................13
6. GENERAL SPECIFICATIONS.......................................................... 20
7. INTERFACE .......................................................................................24
7-1. Interface Specifications ..............................................................24
7-2. Interface Timing .........................................................................24
7-3. Connectors and Signals ..............................................................25
7-4. Setting of DIP Switches .............................................................26
7-5. Peripheral Unit Drive Circuit .....................................................27
7-6. Error Condition Alarm Mode .....................................................27
8. WHEN POWER IS SUPPLIED BY THE USER ............................... 28
9. CHARACTER CODE LIST................................................................30
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. OUTLINE
The DP8340RC series of serial dot matrix printers is for use in ECR, POS,
electronic instruments, banking machines and computer peripheral equipment.
The DP8340RC series include the following features;
1) 2 color printing (Red and Black)
2) High-speed bidirectional printing (2 line/sec, 29 or 44 columns per line)
3) 9-pin print head
4) Parallel interface (Centronics compatible)
5) Commands for expanded characters, inverted characters, emphasized
characters, red and black printing, and 10CPI or 15CPI characters etc. are
provided, which makes the printer very versatile.
6) Simultaneous Data Communication and Printing
7) 2 Peripheral Drivers
8) One line validation printing (Option)
Model Name Notation
– 1 –
Download from Www.Somanuals.com. All Manuals Search And Download.
2. UNPACKING AND INSTALLATION
2-1. Unpacking
After opening the box, check if all necessary accessories are included.
(A) Printer
1 Printer
2 User’s Manual
3 Paper Holders
4 Re-Roll Prevention Guard
5 Ink Ribbon
6 DIP Switch Cover
(B) Power Supply Unit
1
1 Power Supply Unit
2 User’s Manual
Figure 2-1. Unpacking
– 2 –
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2. Installation of Paper Holders and Re-Roll Prevention Guard
Install the Paper Holders in the intermost holes in the rear of the printer.
Figure 2-2. Installation of Paper Holders
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the Re-Roll Prevention Wire in the holes of the printer cover. Twisting the
Wire as shown in the figure below, will make the installation easier.
Figure 2-3. Installation of Re-Roll Prevention
2-3. Handling Notes
(1) Install the printer near an easily accessible socket-outlet.
(2) Place the unit on a flat and stable surface for operation.
(3) Do not connect the AC Power Plug to the same outlet used for other noise
generating devices (large motors, etc.).
(4) Be careful not to drop paper clips, pins and other foreign objects into the
unit.
(5) Wipe off dirt with a soft cloth soaked in alcohol or benzine. Do not use
Lacquer thinner, Trichlorethelene or Ketone solvents because they may
damage plastic parts.
(6) Use a soft brush, etc. for cleaning the printer mechanism and PCB.
(7) Keep hands out of printer while power is on.
(8) Do not attempt to print when there is no ink ribbon or paper in the unit. The
print head life could be severly reduced.
(9) If the paper is fastened tightly to the roll, the paper may not detach from the
roll when the end is reached.
If this happens, the no paper detection function and paper feed will not
operate.
(10) Always keep the printer cover attached when printing to prevent paper
jams, noise, and other problems.
(11) Always turn the power off before opening the printer cover. (e.g. When
renewing a ink ribbon)
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3. PART IDENTIFICATION AND NOMENCLATURE
3-1. Power Supply Unit
DC Power Connector (Output)
Shape of AC Power plug will
vary according to destinations.
Figure 3-1. Power Supply Unit
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2. Printer
Figure 3-2. Printer: Front View
Figure 3-3. Printer: Rear View
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3. Part Functional Description
(1) AC Power Plug
(2) DC Power Outlet
(3) Printer Cover
(4) POWER Lamp
(5) ON LINE Lamp
Connect to an outlet of the specified voltage.
Supplies DC 12V power to the printer.
Protects the printer against dust and reduces noise.
Lights up (green LED) when power is on.
Lights up (green LED) when the unit is in the online
mode.
(6) ALARM Lamp
Lights up (red LED) when printer operation is not
normal, or the printer is out of paper. It is necessary
to install paper into the printer and press the ON
LINE Button to recover from paper empty status.
Turn off the printer power in order to recover from
abnormal operation.
(7) ON LINE Button
(8) FEED Button
Toggles between the on-line and off-line modes. The
printer will go on-line after turning power on.
Momentary operation of this button provides one
line feed. Pressing this button continuously will
cause continuous paper feed. If power is turned on
while pressing this button, self printing*1 will be
performed.
(9) Interface Connector Connects the printer to host computers. Check that
both computer and printer are off before connecting.
(10) DIP Switches
Allows for setting of various functions according to
user requirements.
(11) Peripheral Drive
Output
Connects the printer to the peripheral devices such
as Cash Drawer, Paper Cutter and Paper Take-Up
Device etc. to drive them.
*1 Self Printing
This printer has another convenient function, the
Automatic Test Printing. With the ink ribbon and
paper properly installed in the printer, turn the power
ON while holding down the Feed switch. Test print-
ing will start and stop again automatically.
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
4. INSTALLATION OF INK RIBBON AND PAPER
4-1. Installation of Ink Ribbon
(1) Turn power off, lift the Printer Cover up and remove it.
Note: Be careful not to touch the print head immediately after printing,
because it can get very hot.
Figure 4-1. Printer Cover Removal
(2) Unwind ribbon so that the spools are separated as shown in Figure 4-3.
Hold the ribbon taut as shown with the drive pins facing down and slide the
ribbonbetweentheprintheadandtheplaten. Whilekeepingtheribbontaut,
wrap one side around the black ribbon guide on the end of the platen and
droponespoolonthespoolshaft. Asyoumovethespooldownwards, move
the detecting lever aside to allow the spool to drop into place. Make sure the
spool drive pins engage with the spool drive holes. As the spool drops into
place there will be a click.
(3) While continuing to hold the ribbon taut, install the remaining ribbon spool
in a similar fashion.
(4) Turn the spool that rotates freely to take up the ribbon slack.
Ribbon Life
Ribbon life
Description
Black
Red
SF-03BR
(Fuji Kagakushi
Kogyo Co., Ltd.)
Approx.
0.8 million
characters
– 8 –
Approx.
0.4 million
characters
Download from Www.Somanuals.com. All Manuals Search And Download.
Ribbon Life
Ribbon life
Black
Description
SF-03B
(Fuji Kagakushi
Kogyo Co., Ltd.)
Approx.
0.8 million
characters
Figure 4-2. Installation of Ink Ribbon
Figure 4-3. Ribbon Spools
4-2. Removal of Ink Ribbon
Hold the spool and lift gently, rotating it until the ribbon sags. Push the ribbon
detecting lever out, lift the spool until it comes off the shaft. Remove the second
spool in a similar manner.
(Do not apply excessive force when lifting spools.)
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3. Paper Insertion
4-3-1. For Roll Paper
(1) Cut the Roll Paper end straight and square. Hold the roll so that the paper
comes from the bottom.
(2) Attach the Roll Paper to the Holders Paper by slipping one side of the roll
onto the Hub and pulling the other Hub out to allow the roll to slip in place.
(3) Insert the paper evenly into the Paper Insertion Slot.
(4) Turn the Power Switch “ON”, and press the FEED Button. The paper will
be fed into the unit.
Figure 4-4. Paper Insertion (1)
Figure 4-5. Paper Insertion (2)
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3-2. RollPaperInstallation(WhenusingtheoptionalPrinterCover8340R)
When installing roll paper with the optional “Ptinter Cover 8340R”, please use
the following procedure.
(1) Turn power off, lift the Printer Cover up and remove it.
Note: Be careful not to touch the print head immediately after printing
because it can get very hot.
(2) Insert paper into the printer, and feed the paper so it extends 3 inches or
more above the top surface of the printer.
(3) Insert the paper into the slot in the “Printer Cover 8340R”.
(4) Install the “Printer Cover 8340R” on the printer.
Figure 4-6. Replace the Printer Cover
Figure 4-7. Printer Cover 8340R
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3-3. Validation Option Installation
The validation printing requires the optional printer cover 8340R. Refer to
item 4-3-2 for the installation.
(1) Turn power ON.
(2) Enter the printer the validation mode.
(Refer to the control code “GS” in Chapter 5.)
(3) Insert the material to be validated against the right side of the slot in the
Printer Cover 8340R.
Figure 4-8. Insertion of Material to be validated
4-4.
Roll Paper Removal
Cut the paper close to the slot and use the feed button until paper has passed
completely through the printer.
Note: Do not try to remove the paper by hand as it could become crooked and
get jammed inside the printer.
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
5. CONTROL CODES
LF
(0A)H
CODE
FUNCTION
Print and line feed instruction
OUTLINE
The LF code causes the data in the line buffer to be printed,
followed by a single line feed. When the line buffer is empty,
only the feed takes place.
CR
(0D)H
CODE
FUNCTION
Print and line feed instruction
Same function as of LF code.
OUTLINE
However, when the DIP switch 3 is ON, the CR code be-
comes invalid.
CODE
SO
(0E)H
Expanded character instruction
FUNCTION
OUTLINE
This code causes the printer to print expanded characters
twice as wide as the regular ones. This remains in effect until
a DC4 code is received.
DC4
(14)H
CODE
FUNCTION
Release from expanded characters
OUTLINE
The expanded character instruction is released by the DC4
code, and the succeeding data is printed as regular width
characters.
CODE
ESC-1
(1B)H (2D)H (01)H or (1B)H (2D)H (31)H
Underline mode selection
FUNCTION
OUTLINE
All data received after this code is underlined until a ESC-0
is received.
ESC-0
CODE
(1B)H (2D)H (00)H or (1B)H (2D)H (30)H
Release from underline mode
FUNCTION
OUTLINE
The underline mode selection is released by this code.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
SI
(0F)H
CODE
FUNCTION
Inverted print instruction
OUTLINE
This function causes the printing to be inverted. This code
must be received at the beginning of a line. If this code is
received anywhere other than at the beginning of a line, it is
disregarded. Accordingly, normal characters and inverted
characters, can not be mixed on the same line.
DC2
(12)H
CODE
FUNCTION
Release from inverted print instruction
OUTLINE
The inverted print instruction is released by this code. This
code must be received at the beginning of a line.
ESC E
(1B)H (45)H
CODE
FUNCTION
Emphasized print mode instruction
OUTLINE
Data following this command is printed with emphasized
characters.
In this mode, characters are printed in a single direction.
ESC F
(1B)H (46)H
CODE
FUNCTION
Release from emphasized print instruction
Emphasized print is released.
OUTLINE
ESC 4
(1B)H (34)H
CODE
Red character print instruction
FUNCTION
OUTLINE
This command causes subsequent data to be printed with red
characters.
The instruction is released by the code, ESC 5.
Red and black characters may be intermixed.
This command is ignored when DIP SW 5 is OFF.
ESC 5
(1B)H (35)H
CODE
FUNCTION
Release from red character print instruction
OUTLINE
The red character print instruction is released by this code.
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ESC a n
(1B)H (61)H
CODE
n
n-line feed
FUNCTION
OUTLINE
Afterprintingthedatainthecurrentline,nlinesarefedbythis
code. The value of n ranges from 1 to 120.
ESC C n
(1B)H (43)H
CODE
n
FUNCTION
Sets page length in lines
OUTLINE
This code sets the length of a page to n lines. The value of n
ranges from 1 to 120. On initialization, the page length
default condition will be 42 lines. The line feed pitch is one-
sixth inch.
ESC Nn
(1B)H (4E)H
CODE
n
Sets bottom margin in lines
FUNCTION
OUTLINE
Upon receiving this code, the bottom margin is set to n lines.
0
n
120; Default Value n = 0
ESC O
(1B)H (4F)H
CODE
Cancels bottom margin.
FUNCTION
OUTLINE
Upon input of this code, bottom margin setting is cleared.
FF
(0C)H
CODE
Form feed
FUNCTION
OUTLINE
The FF code prints the data in the current line and transports
the paper to the start of the next page.
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ESC @
(1B)H (40)H
CODE
Printer initialization
FUNCTION
OUTLINE
All printing conditions except ESC BEL n1 n2, the line buffer
and data buffer are set to the power on default condition.
ESC BEL n1 n2
(1B)H (07)H n1 n2
CODE
Sets peripheral unit drive 1 pulse duration.
FUNCTION
OUTLINE
This command sets the pulse duration for peripheral unit
drive (Paper Cutter, Take-Up Device, cash drawer, etc.)
Pulse Duration = 10 × n1 (ms)
Delay = 10 × n2 (ms)
1
n1
127; 1
n2
127
Default value: n1 = n2 = 20
Executed by BEL code and FS code after printing.
BEL
(07)H
CODE
FUNCTION
Trigger peripheral unit drive 1 (Deferred)
OUTLINE
Causes a peripheral drive 1 pulse to be generated. This code
is normally stored in the buffer and is performed as it is
received from the data queue.
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
FS
(1C)H
CODE
FUNCTION
Trigger peripheral unit drive 1 (immediate)
OUTLINE
Causesaperipheraldrive1pulsetobegeneratedimmediately
SUB
(1A)H
CODE
Trigger peripheral unit drive 2 (immediate)
FUNCTION
OUTLINE
This command causes a peripheral unit drive 2 pulse to be
generated.
Pulse Duration : 200ms (fixed)
Delay
: 200ms (fixed)
It is impossible to drive peripheral devices 1 and 2 at the
same time.
REMARKS
CAN
(18)H
CODE
FUNCTION
Clears print buffer
OUTLINE
Upon input of this code the data buffer and line buffer are
cleared.
ESC P
(1B)H (50)H
CODE
Select 10 CPI
FUNCTION
OUTLINE
This code causes the printer to print at 10 CPI. The number
of columns per is 29.
ESC M
(1B)H (4D)H
CODE
FUNCTION
Select 15 CPI
OUTLINE
This code causes the printer to print at 15 CPI. The number
of columns per line is 44. When the power is turned on, the
15 CPI mode is selected.
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
GS
(1D)H
CODE
Validation printing instruction
FUNCTION
OUTLINE
This code causes the printer to perform validation printing
of a maximum of 32 subsequent characters (at 15 CPI, from
the thirteenth to the forty-forth column).
After the GS code is received, a maximum of 32 characters
should be input, followed by the LF code which indicates
the end of the validation printing data.
(At this time, control codes except FS, ENQ, CAN and SUB
codes, or any character received beyond the limit of 32
characters are ignored.)
When the printer enters the validation mode, the ribbon is
shifted up and the ON-LINE lamp blinks. (This lamp goes
on and off at a 0.5-second interval until the end of the va-
lidation mode.) Afterthematerialtobevalidatedisinserted,
and the LF button is pressed, the validate line is printed,
followed by a single line feed. When the check is removed
and the ON-LINE button is pressed, the printer returns to
regular mode and is set to ON-LINE status.
1) The print settings by commands (such as emphasized
mode and underline mode) are invalid only during val-
idation printing.
REMARKS
2) When the CAN code is received in the validation mode,
the printer returns to regular mode, and the mechanism
is initialized.
3) If the FS or SUB codes is received in the validation
mode, these codes are executed just after the printer
returns to regular mode.
4) In the validation mode, the LF button and the ON-LINE
button do not work except the above behavior.
5) If the printer has a Red black ribbon installed, the va-
lidate line will be printed in red.
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Character Code List
Character
LF
Code
Function
1
2
(0A)H
(0D)H
Print and line feed instruction
Print and line feed instruction
(same as LF)
CR
3
4
5
SO
(0E)H
(14)H
Expanded character instruction
Expanded character release
Underline instruction
DC4
ESC-1
(1B)H (2D)H(01)H
(1B)H (2D)H (31)H
(1B)H (2D)H(00)H
(1B)H (2D)H (30)H
(0F)H
6
ESC-0
Underline release
7
8
9
SI
Inverted print instruction
Inverted print release
DC2
ESC E
(12)H
(1B)H (45)H
Emphasized print instruction
(one-way printing)
10 ESC F
11 ESC 4
12 ESC 5
13 ESC a n
14 ESC C n
(1B)H (46)H
(1B)H (34)H
(1B)H (35)H
(1B)H (61)H n
(1B)H (43)H n
Emphasized print release
Red character print instruction
Red character print release
n-line feed instruction
Sets page length in lines
1
n
120 (default n = 42)
Set bottom margin in lines
120 (default n = 0)
15 ESC N n
(1B)H (4E)H n
0
n
16 ESC O
17 FF
(1B)H (4F)H
(0C)H
Cancel Bottom margin
Form feed
18 ESC @
19 ESC BEL
n1 n2
(1B)H (40)H
(1B)H (07)H
n1 n2
Printer initialization instruction
Set peripheral unit drive 1 pulse duration
1
n1
127, 1
n2
127
(default n1 = n2 = 20)
20 BEL
21 FS
(07)H
(1C)H
Trigger peripheral unit drive 1 (Deferred)
Trigger peripheral unit drive 1
(Immediate)
22 SUB
(1A)H
Trigger peripheral unit drive 2
(Immediate)
23 CAN
24 ESC P
25 ESC M
26 GS
(18)H
Clears print buffer
(1B)H (50)H
(1B)H (4D)H
(1D)H
Select 10 CPI
Select 15 CPI (Default value)
Validation printing instruction
– 19 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6. GENERAL SPECIFICATIONS
Printing method
Serial impact dot matrix printing,
9 wires
Number of print columns 29 columns (10CPI), 44 columns (15CPI)
Print speed
Print direction
Line spacing
Approx. 2 lines/sec
Bi-directional
1/6 inch
Paper feed method
Paper feed speed
Character set
Friction Feed
Approx. 12 lines/sec
ASCII
Special
Block graphics*
Katakana (Japanese)
96 characters
64 characters
64 characters
64 characters
Font configuration
10CPI Ordinary characters 5 × 9 dots
Block graphics* 6 × 6 dots
15CPI Ordinary characters 7 × 9 half dots
Block graphics* 5 × 6 dots
* Graphic Feed Not Available
Character size
Character spacing
Dot spacing
Gross dot
10CPI 2.00 (H) × 2.42 (V) mm
15CPI 1.32 (H) × 2.42 (V) mm
10CPI 2.55 mm (1/10 inch)
15CPI 1.70 mm (1/15 inch)
10CPI H=0.425 mm V=0.353 mm
15CPI H=0.340 mm V=0.353 mm
10CPI 174 dots/wire/line
15CPI 220 dots/wire/line
Print area
10CPI 73.53 mm
15CPI 74.46 mm
Print Buffer
Interface
Peripheral drive
Approx. 1.5 KB
Parallel Interface (Centronics compatible)
2 outputs (each 1A max. at 12V. Both cannot
operate at the same time.)
External dimensions
(Printer)
202(W) × 200(D) × 98(H) mm
(without paper holder, DC Power Connector)
60(W) × 120(D) × 36(H) mm (without AC cable)
(Power supply unit)
Weight
(Printer)
(Power supply unit)
Approx. 1.9 kg
Approx. 0.4 kg (without AC cable)
– 20 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Power supply unit
Four supplies available with following ratings
Input
Output
AC 100 – 240 V
47Hz – 63 Hz
0.8 A Max
DC 12.0 V ± 5%
2.0 A
Paper specification
Paper type
Size Paper width
Roll diameter
Thickness (single)
(2 copy)
Ordinary and carbonless copy paper
82.55 ± 0.5mm (3.25 inches)
80 mm outer diameter (Max)
0.07 mm (52.3 g/m2) to 0.09 mm (64g/m2)
One copy and one original (max 0.13 mm)
Paper should not be attached to the core
Check (Refer to Fig. 6-2)
Paper end
One line validation
Paper width 70 to 90 mm
Thickness 0.1 to 0.15 mm
* Requires the optional Printer Cover 8340R
Ink ribbon specification
Color
Ribbon material
Ribbon size
Spool
Black and red / Black only
Nylon (#40 denier)
13mm × 6m
13mm (width), 35mm in diameter (two spool)
Recommended ribbon SF-03BR (Black and red), SF-03B (Black)
(manufactured by Fuji Kagakushi Kogyo Co., Ltd.)
or approved equivalent.
Operating conditions
Temperature
Humidity
Temperature
Humidity
+5˚C — +40˚C
10% — 80%RH
–20˚C — +70˚C
5% — 95%RH (+40˚C)
Storage conditions
Head life
70 million characters
Printer reliability
5.0 million lines MCBF (except head life)
– 21 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6-1. Roll Paper and Print Area
Figure 6-2. Material to be validated and One Line Validation Printing
– 22 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6-3. External Dimensions (Printer)
36mm
120mm
2.0m
Shape of AC Power plug will
vary according to destinations.
Figure 6-4. External Dimensions (Power Supply Unit)
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7. INTERFACE
7-1. Interface Specifications
This printer has a parallel interface to communicate with the computer.
The operating specifications of the parallel interface are as follows.
(1) Data transfer rate
(2) Synchronization
(3) Handshaking
(4) Logic level
1000 to 6000 characters per second
Via externally supplied STROBE pulses
ACK and BUZY signals
Compatible with TTL level
7-2. Interface Timing
Figure 7-1. Interface Timing Diagram
Signal Name
Circuit Example
DATA1-DATA8
(To Printer)
STROBE
(To Printer)
BUZY, ACK
(From Printer)
Figure 7-2. Typical Interface Circuit
– 24 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7-3. Connectors and Signals
Pin No.Signal Name IN/OUT
Function
Signals when data is ready to be read.Signal
gose from HIGH to LOW (for at least 0.5
microsec.) when data is available.
These signals provide the information of the
first to eighth bits of parallel data.Each signal
is at HIGH level for a logical 1 and at a LOW
level for a logical 0.
1
STROBE
IN
2-9 DATA1-8
IN
A 9 microsecond LOW pulse acknowledges
receipt of data.
When this signal goes LOW, the printer is ready
to accept data. When the printer is in one of
the conditions below.”HIGH” is set.
1. Data being entered.
2. Off line.
3. Error condition.
This signal is normally LOW. It will go HIGH
if the printer runs out of paper.
10
11
12
ACK
OUT
BUSY
OUT
OUT
PAPER
OUT
13 SELECTED OUT ThissignalisHIGHwhentheprinterisonline.
14-15
N/C
SIGNAL
GND
Unused
16
Signal ground.
CHASSIS
17
Chassis ground, isolated from logic ground.
GND
18
19-30
N/C
GND
Unused
Twisted pair return signal ground level.
When this signal gose LOW, the printer is reset
to its power-on condition.
31
RESET
IN
This signal is normally HIGH. This signal goes
LOW to signal that the printer cannot print
due to an error condition.
32
ERROR
OUT
Refer to Item 7-6 Emergency Suspension.
External ground.
Unused.
33 EXT GND
34-36 N/C
Figure 7-3. Parallel Interface Connector (Printer side)
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4. Setting of the DIP Switches
Factory settings : all ON
ON OFF
Switch
Function
Character Table
1
U.S.A. & Europe
Japan
2
Unused
3
4
CR cord
Unused
Disable
Enable
5 (*1)
Ink Ribbon
2-color
Monochrome
6
7
8
International Character Set (See below)
(*1) DIP Swich 5 should be set to ON when you use a 2-color ribbon
for 2-color printing.
It should be set to OFF when a monochrome ribbon is used.
International Character Set
SW NO. USA
France Germany England Denmark Sweden
Itary
ON
OFF
OFF
Spain
OFF
OFF
OFF
6
7
8
ON
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
ON
OFF
Note: When DIP Switches 1 is set to OFF, the printer always selects the
Japan international character set regardless of the status of DIP
Switches 6, 7 and 8.
When DIP Swiches 1 is otherwise set, the printer selects the
character set determined by DIP Switches 6, 7 and 8.
Figure 7-4. DIP Switch Setting
– 26 –
Download from Www.Somanuals.com. All Manuals Search And Download.
7-5. Peripheral Unit Drive Circuit
The Control Board of this printer is equipped with a circuit for driving peripheral
units (Paper Cutter, Take-Up Device, Cash Drawer, etc.)
The 6P Modular Jack is used as the Drive Circuit. When using this circuit,
connect the peripheral unit cable to the 6P Modular Jack (cable is not included).
Note: Peripheral unit drive circuit connector only connects to peripheral units
such as cash drawers, etc.Do not connect it to a telephone.
1. Drive Circuit
Drive
Output
12V,MAX. 1A
Absolute Ratings (Ta = 25˚C)
D1
D2
Voltage Breakdown
Peak Forward Current
100V
1A
Note: It is impossible to drive pe-
ripheral devices 1 and 2 at
the same time
[Printer side]
Figure 7-5. Drive Circuit
Figure 7-6. 6P Modular Jack
Connector
Figure 7-7. Recommend Cable
Note: Make sure that the metal structural parts of the peripheral device are
connected to frame Ground (Pin 1) to provide a static drain path.
2. Control code
Codes for Drive Circuit control are ESC BEL n1 n2, BEL, FS and SUB.
Refer to the Control Codes in Section 5.
7-6. Error Condition Alarm Mode
If an error condition is detected during operation, the printer will stop printing
and cause the ERROR signal to go Low. All solenoids & motors will be de-
energized. It is necessary to turn the printer power off and on again in order to
recover from the alarm mode.
The printer can detect the following error conditions:
a. Motor Lock
b. Defective timing detector
c. Micro-processor out of program sequence
– 27 –
Download from Www.Somanuals.com. All Manuals Search And Download.
8. WHEN POWER IS SUPPLIED BY THE USER
When printer power is supplied by the user rather than through the accessory
power source unit, please be careful of the following points.
+10%
–5%
Note 1: The power supply must be +12V
2A or above. An electrolytic ca-
pacitor (C = 4700µF/25V to 6800µF/25V) must be connected across
the output of the power supply.
Note 2: A DC power plug is available as an option.
Reference: Design the power supply referring to the power supply circuit shown
below.
Note: A line noise filter must be used to prevent line transients from passing
through power supply. Filter design to be determined by environmental
noise requirements.
– 28 –
Download from Www.Somanuals.com. All Manuals Search And Download.
VAC
VDC
IAC
C1
14V
12V
C2
ZD1
C3
100 ~ 200µF/25V
VZD = 14V (1W)
4700 ~ 6800µF/25V
2SD633 (TOSHIBA)
+10%
–5%
2 ~ 3A
6800µF/25V
TR1
Other parameters may be determined by user.
Figure 8-1. Power Supply Reference Circuit
– 29 –
Download from Www.Somanuals.com. All Manuals Search And Download.
9. CHARACTER CODE LIST
1) U.S.A. & Europe (DIP SW1: ON)
– 30 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 31 –
Download from Www.Somanuals.com. All Manuals Search And Download.
2) JAPAN (DIP SW1: OFF)
– 32 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 33 –
Download from Www.Somanuals.com. All Manuals Search And Download.
International Character Sets
– 34 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRONIC PRODUCTS DIVISION
STAR MICRONICS CO., LTD.
536 Nanatsushinnya, Shimizu, Shizuoka
424-0066 Japan
OVERSEAS SUBSIDIARY COMPANIES
STAR MICRONICS AMERICA, INC.
70-D Ethel Road West, Piscataway, NJ 08854 U.S.A
Tel: 732-572-9512, Fax: 732-572-5095
Tel: 0543-47-0112, Fax: 0543-48-5271
STAR MICRONICS U.K. LTD.
Please access the following URL
Star House, Peregrine Business Park, Gomm Road,
High Wycombe, Bucks, HP 13 7DL, U.K.
Tel: 01494-471111, Fax: 01494-473333
for the lastest revision of the manual.
1999.05.30
Printed in Japan, 80870195
Download from Www.Somanuals.com. All Manuals Search And Download.
|