FADER CLEANING
The SK SIX faders may need lubrication from time to time. This will extend the
fader life and eliminate any potential damage due to extended heavy usage.
S K S IX Professional performance mixer
Cleaning Instructions
cable coming from the mixer.
1. Remove the 3 fader knobs and 4 screws
located in the corners of the PROTEKT™
3. Spray a small amount of cleaner or
lubricant into both ends of the fader and
slide the fader back and forth a few times
to spread the fluid evenly throughout the
fader.
(see “
” inside) panel
and take the panel off the mixer.
2 . Remove the fader to be cleaned by
unscrewing the 2 outer screws (removing
the 2 inner screws will detach the fader
from the fader plate) and disconnect the
4. Shake and wipe off excess fluid before
re-assembling the fader.
REPL ACEMENT PARTS
To replace the cross or channel faders, follow steps 1 and 2 of the cleaning
instructions. The following replacement parts are available from Stanton or your
local Stanton dealer.
PL-SK6
Two way input toggle switch
PP-SK6
PROTEKT™ panel
3PL-SK6 Three way input toggle
switch with FLASH™
PS-18US US Power Supply (110v)
LF-SK6
CF-SK6
Channel input fader
Crossfader
PS-18EU European Power Supply (220v)
PS-18UK UK only Power Supply (240v)
ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES
REPLACING INSTRUCTIONS
ROTATING INSTRUCTIONS
1. Remove the PROTEKT™ panel
1 . Remove the PROTEKT™ panel
O W N E R ’S M A N U A L
2. Remove the 2 outer screws from the
round plate (removing the 2 inner screws
will detach the switch from the plate)
2. Remove the 2 outer screws from the
round plate (removing the 2 inner screws
will detach the switch from the plate)
3. Remove the switch assembly and dis-
connect the cable coming from the mixer.
3. Rotate the plate to the desired position
and tighten the screws back in the top and
bottom holes
4. Set the replacement switch assembly in
the desired position and place the screws
back in the top and bottom holes.
S TANTON M AGNETICS , LLC
2 8 2 1 Evans St. Hollywood, FL 3 3 0 2 0
(9 5 4 ) 9 2 9 -8 9 9 9 - Fax: (9 5 4 ) 9 2 9 -0 3 3 3
info@stantonmagnetics.com
© 1999, Stanton Magnetics, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF FUNCTIONS
1. Mic level control: Controls the overall microphone output level.
2. Send: Controls the level of the effect send output. this is used to set the level of the
signal going to the outbpard effects processor or stomp box.
3. Return: Controls the level of the effect return input. This is used to control the level of
the processed signal going back into themixer
4. FX: Effect ON/OFF for each channel, MIC, and cue.
5. Gain: Controls the input level of each channel.
6. EQ: Individual controls for low and high frequency equalization with (+9/-26 dB)
Any changes made to EQ settings will change the overall output level.
7. Master level control: Controls the overall signal output level.
8. Headphone level control: Controls the overall headphone output level. It is recom-
mended headphones with an impedance rating of 200 ohms or less be used for maxi-
mum volume.
9. Cue pan: Fades the headphone output between channels 1 and 2, effectively allowing
the user to preview a mix.
10. Power indicator: Blue LED indicates whether mixer is ON or OFF.
11. Input selector switches: Selects phono or line inputs. FLASH™ position allows users
to quickly trigger the phono input.
12. Input Fader Reverse: Reverses the direction of each respective input channel fader.
Includes bi-color LED to indicate the status of the reverse function. When LED is
green, the fader is normal. When LED is red, the fader direction is reversed.
13. Channel fader: Controls the input channel level.
14. Headphone mute: Mutes the headphones without having to change its level.
15. Input Level Meter: Monitors each channel’s input level with peak hold function
16. Crossfader Reverse LED: Bi-color LED indicates the status of the crossfader reverse-
function. When LED is green, the crossfader is normal. When LED is red, the crossfader
direction is reversed.
17. Crossfader: Fades the master output between channels 1 and 2.
SPECIAL PROTE K TI O N
18. Headphone output: Connection for 1/4 inch headphone. Recommended headphone
Your SK SIX comes with a special PROTEKT™ aluminum panel designed to
make the surface of the mixer is as smooth as possible while still enabling you
to field-replace key components. The PROTEKT™ panel covers all screws that
may get in the way of your performance. You can still easily remove the front
panel to replace any of the modular parts which are subject to wear and tear:
crossfader, input faders and input toggle switches.
impedance is 32-200 ohms for maximum volume.
19. Crossfader Reverse: Reverses the direction of the crossfader.
20. Crossfader Curve adjustment: Adjusts the shape of the crossfader curve from a quick
cut for scratching and cutting to a longer fade for mixing.
20. Send & return connections: The send output is used to connect the mixer to the line
input of your effects processor or sampler. The return input is used to feed the sgnal
The PROTEKT™ panel is also reversible. If you happen to scratch or blemish the
front side, just flip-it over since it is screened on both sides!
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONS (cont’d)
TECHNIC AL SPECIFIC ATIONS
Line inputs:
Phono inputs:
Semd:
Return:
DJ mic input:
Master output:
2 (RCA), 150 mV / 27K ohm
2 (RCA), 3 mV / 47K ohm
2 (1/4”), 150 mV / 27K ohm
2 (1/4”), 775 mV / 1K ohm
1 (1/4 inch), 1.5 mV / 3K ohm
1 (1/4” TRS Balanced/RCA unbalanced),
1.2 V / 100 ohm
Record output:
Headphone output:
Crossfader type:
Frequency Response:
Tone Control :
Gain Control:
1 (RCA), 245 mV / 100 ohm
1 (1/4 inch), 32 - 200 ohms recommended
VCA
20 Hz - 20 kHz, +/- 2 dB
+ 9/-26 dB (Hi, Low)
20dB / 1 Khz
S/N Ratio:
Less than 70dB
T.H.D:
Dimension(LxWxD):
less than 0.2%
12 3/8” x 10 1/4” x 4” ( 314 x 260 x 102 mm)
Weight:
7 lbs (3.2 Kg)
WARRANT Y
back from the line output of the outboard unit. This creates the effects loop.
22. Power switch: Selects power "ON" or "OFF".
This unit has been designed and manufactured using quality
components. Therefore, it is warranted to be free from defects in materi-
als (limited as specified below), and workmanship for a period of twelve
(12) months from the original purchase date. During this period, all
service and parts necessary to repair a defect will be free of charge. This
limited warranty applies to mechanical parts which are subject to wear
and tear as specified:
23. Power supply connector: Input connection for the accompanying power supply.
24. Master output: TRS balanced 1/4” master outputs.
25. Outputs: Record out and unbalanced master RCA.
26. Inputs: Line and phono signal inputs for channels 1 and 2. See note below.
27. Microphone input: 1/4” connector
• Faders, specified durability: 15,000 cycles
• Rotary potentiometers, specified durability: 10,000 cycles
• Switches, specified durability: 10,000 cycles
28. Ground connectors: Connect to the turntables’ground connectors to eliminate electri-
cal hum. Ground connectors are usually supplied with turntables.
Consequently, the parts listed above are warranted to be free from
defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
Note on audio signal inputs/outputs: Line inputs are used to connect to line level
sources such as CD players, samplers, tape players, etc. Phono inputs are
used to connect to turntables. Master output connects to an amplifier, EQ,
crossover, or other outboard signal processing. Record out connects to tape
recorder, mini disk recorder, etc.
FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE
ONLINE WARRANTY REGISTRATION FORM FOUND AT
WWW.STANTONMAGNETICS.COM
2821 Evans Street • Hollywood, FL 33020
Download from Www.Somanuals.com. All Manuals Search And Download.
|