S K F IV E
Professional performance mixer
O W N E R ’S M A N U A L
S TANTON M AGNETICS , LLC
2 8 2 1 Evans St. Hollywood, FL 3 3 0 2 0
(9 5 4 ) 9 2 9 -8 9 9 9 - Fax: (9 5 4 ) 9 2 9 -0 3 3 3
info@stantonmagnetics.com
© 1999, Stanton Magnetics, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF FUNCTIONS
1. Gain control: Controls the input sensitivity of each channel.
2. Input selector switches: Selects phono or line inputs.
3. Master level control: Controls the overall signal output level.
4. Mic gain control: Controls the overall microphone output level.
5. Channel fader: Controls the input channel level.
6. Crossfader Reverse LED: Bi-color LED indicates the status of the crossfader reverse
function. When LED is green, the crossfader is normal. When LED is red, the crossfad-
er direction is reversed.
7. Crossfader: Fades the master output between channels 1 and 2.
8. Power switch: Selects power "ON" or "OFF".
9. Cue pan: Fades the headphone output between channels 1 and 2, effectively allowing
the user to preview a mix.
10. Headphone level control: Controls the overall headphone output level. It is recom-
mended headphones with an impedance rating of 200 ohms or less be used for maxi-
mum volume.
11. Input Level Meter: Monitors each channel’s input level.
12. Microphone input: 1/4” connector
13. Crossfader Curve adjustment: Adjusts the shape of the crossfader curve from a quick
cut for scratching and cutting to a longer fade for mixing.
14. Crossfader Reverse: Reverses the direction of the crossfader. Bi-color LED indicates
the status of the crossfader reverse function. When LED is green, the crossfader is
normal. When LED is red, the crossfader direction is reversed.
15. Headphone Mute: Mutes the headphone signal output
16. Headphone output: Connection for 1/4 inch headphone. Recommended headphone
impedance is 32-200 ohms for maximum volume.
17. Power supply connector: Input connection for the accompanying power supply.
18. Master output: TRS balanced (1/4”).
19. Master output: unbalanced RCA connector
20. REC output: record output connects directly to recording source (tape deck, CD...)
21/22. Channel inputs: Line and phono signal inputs. Line inputs are used to connect
to line level sources such as CD players, samplers, tape players, etc. Phono
inputs are used to connect to turntables.
23. Ground connector: Connects to the turntable ground connector to eliminate electri-
cal hum. Ground connectors usually supplied with turntables.
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNIC AL SPECIFIC ATIONS
FADER CLEANING
Line inputs:
Phono inputs:
Master output:
2 (RCA), 150 mV / 27K ohm
2 (RCA), 3 mV / 47K ohm
1 (1/4” TRS Balanced/RCA unbalanced),
775 mV / 1K ohm
The SK FIVE faders may need lubrication from time to time. This will extend the
fader life and eliminate any potential damage due to extended heavy usage.
Cleaning Instructions
cable coming from the mixer.
Record output:
Headphone output:
Frequency Response:
Gain Control:
S/N Ratio:
T.H.D:
Dimension(LxWxD):
Weight:
1 (RCA), 245 mV / 10K ohm
1 (1/4 inch), 32 - 200 ohms recommended
20 Hz - 20 kHz, +/- 2 dB
0-20dB
Less than 70dB
less than 0.2%
1. Remove the 3 fader knobs and 4 screws
located in the corners of the PROTEKT™
3. Spray a small amount of cleaner or
lubricant into both ends of the fader and
slide the fader back and forth a few times
to spread the fluid evenly throughout the
fader.
(see “
” inside) panel
and take the panel off the mixer.
2 . Remove the fader to be cleaned by
unscrewing the 2 outer screws (removing
the 2 inner screws will detach the fader
from the fader plate) and disconnect the
4. Shake and wipe off excess fluid before
re-assembling the fader.
9” x 9.75” x 3.5” ( 226 x 248 x 87 mm)
7 lbs (3.2 Kg)
REPL ACEMENT PARTS
WARRANT Y
To replace the cross or channel faders, follow steps 1 and 2 of the cleaning
instructions. The following replacement parts are available from Stanton or your
local Stanton dealer.
This unit has been designed and manufactured using quality
components. Therefore, it is warranted to be free from defects in materi-
als (limited as specified below), and workmanship for a period of twelve
(12) months from the original purchase date. During this period, all
service and parts necessary to repair a defect will be free of charge. This
limited warranty applies to mechanical parts which are subject to wear
and tear as specified:
PL-SK1
Two way input toggle switch
PP-SK5
PROTEKT™ panel
3PL-SK1 Three way input toggle
switch with FLASH™
PS-13US US Power Supply (110v)
LF-SK5
CF-SK5
Channel input fader
Crossfader
PS-13EU European Power Supply (220v)
PS-13UK UK only Power Supply (240v)
• Faders, specified durability: 15,000 cycles
• Rotary potentiometers, specified durability: 10,000 cycles
• Switches, specified durability: 10,000 cycles
ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES
REPLACING INSTRUCTIONS
ROTATING INSTRUCTIONS
Consequently, the parts listed above are warranted to be free from
defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
1. Remove the PROTEKT™ panel
1 . Remove the PROTEKT™ panel
2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)
2. Remove the 2 outer screws from the tog-
gle switch plate (removing the 2 inner
screws will detach the switch from the
plate)
FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE
ONLINE WARRANTY REGISTRATION FORM FOUND AT
WWW.STANTONMAGNETICS.COM
3. Remove the switch assembly and dis-
connect the cable coming from the mixer.
3. Rotate the plate to the desired position
and tighten the screws back in the top and
bottom holes
2821 Evans Street • Hollywood, FL 33020
4. Set the replacement switch assembly in
the desired position and place the screws
back in the top and bottom holes.
Download from Www.Somanuals.com. All Manuals Search And Download.
|