PRO-30
PROFESSIONAL STEREO PREAMP MIXER
OWNER’S MANUAL
PRO-30
Register this product online
@
@
STANTON MAGNETICS, LLC
© 1999, Stanton Magnetics, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF FUNCTIONS
7. Meter mode selector: Determines the setting of the level meter (6). When pressed,
cue levels of channels 1 and 2 are displayed. When released, stereo master output
signal is displayed.
8. Power switch: Selects power "ON" or "OFF"
9. Fader Start controls: Activate the Fader Start function when connected to a CD player
with fader start capabilities (such as the Next! NCD-7000). When fader start is
engaged, the CD player can be started and paused by the crossfader. This function is
defeated while crossfader is reversed.
10. Master level control: Controls the overall signal output level of the Master output
11. Booth level control: Controls the overall signal output level of the Booth output
12. Cue level control: Controls the overall headphone output level.
13. Cue select: 3 position selector switch dtermines what is heard in the headphones,
channel 1, 2, or master output
14. Headphone output: Connection for 1/4 inch headphone.
headphone impedance is 32-200 ohms for maximum volume
Recommended
15. Mic EQ: Individual controls for low and high frequencies equalization with (+/-12 dB)
Any changes made to EQ settings will change the overall microphone output
level.
16. Mic volume control: Controls the overall mirophone output level
17. Crossfader Reverse: Reverses the direction of the crossfader. The fader start function
is defeated while crossfader is reversed.
18. Microphone input: 1/4” connector
19. Ground connector: Connects to the turntable ground connector to eliminate electrical
hum. Ground connectors are usually supplied with turntables
20. Phono/CD inputs: Switchable line / phono signal inputs for channels 1 and 2
21. Line inputs: Line signal inputs for channels 1 and 2
22. Phono/CD selector switches: Switches CD/Phono inputs for channels 1 and 2 between
line and phono
23. Fader Start output: Connects to the fader start inputs of CD players with fader start
function such as the Next! NCD-7000
24. Booth output: Auxiliary output, usually for DJ booth monitoring. Level is controlled by
booth level control (11)
25. Master output: Level is controlled by master level control (10)
26. REC output: Record out connects to tape recorder, mini disk recorder, etc. to
record performance
27. Voltage selector: Selects between 115V (US) / 230V (EU)
28. Power cord connector: Input connection for the supplied removable power cord.
1. Input selector switches: Selects phono or line inputs of channels 1 and 2
2. Gain control: Controls the input sensitivity of channels 1 and 2
3. Equalizer: Individual controls for low frequency, midrange, and high frequency
equalization with (+9/-26 dB)
overall output level.
Any changes made to EQ settings will change the
4. Channel faders: Control the output level of channels 1 and 2
5. Crossfader: Fades the master output between channels 1 and 2
6. Level meter: Based upon the meter mode selector (7) setting, the level meter displays
the master output stereo signal level, or the cue levels of channels 1 and 2
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFIC ATIONS
CROSSFADER CLEANING
Line inputs:
2 (RCA), 150 mV / 47K ohm
2 (RCA), 3 mV / 47K ohm
1 (1/4 inch), 1.6 mV / 600 ohm
1 (RCA), 1V / 600 ohm
1 (RCA), 350 mV / 600 ohm
1 (1/4 inch), 32 - 200 ohms recommended
20 Hz - 20 kHz, +/- 0.5 dB
+ 9/-26 dB (Hi, Mid, Low)
Hi/Mid/Lo +/-12 dB
The PRO-30 crossfader may need lubrication from time to time. This will extend
the fader life and eliminate any potential damage due to extended heavy usage.
Phono inputs:
DJ mic input:
Master output:
Record output:
Headphone output:
Frequency Response:
Tone Control :
Mic Tone:
Cleaning Instructions
1. Remove the crossfader by unscrewing the 2 outer screws (removing the 2
inner screws will detach the fader from the fader plate) and disconnecting the
cable from the mixer.
2. Spray a small amount of cleaner or lubricant into both ends of the fader and
slide the fader back and forth a few times to spread the fluid evenly throughout
the fader.
Gain Control:
S/N Ratio:
T.H.D:
0-20dB
Less than 80dB
0.01% at 1KHz
Dimension(LxWxD):
Weight:
8.6” x 12.2” x 3.94” (220 x 310 x 100 mm)
8 Lbs (3.5 Kg) power supply included
3. Shake and wipe off excess fluid before re-assembling the fader.
WARRANT Y
CROSSFADER REPL ACEMENT
To replace the cross or channel faders, follow step 1 of the cleaning instructions.
Replacement parts are availabe from Next! or your local Next! dealer.
This unit has been designed and manufactured using quality
components. Therefore, it is warranted to be free from defects in materi-
als (limited as specified below), and workmanship for a period of thirty
six (36) months from the original purchase date. During this period, all
service and parts necessary to repair a defect will be free of charge. This
limited warranty applies to mechanical parts which are subject to wear
and tear as specified:
• Faders, specified durability: 15,000 cycles
• Rotary potentiometers, specified durability: 10,000 cycles
• Switches, specified durability: 10,000 cycles
Consequently, the parts listed above are warranted to be free from
defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE
ONLINE WARRANTY REGISTRATION FORM FOUND AT
WWW.STANTONMAGNETICS.COM
2821 Evans Street • Hollywood, FL 33020
Download from Www.Somanuals.com. All Manuals Search And Download.
|