Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Basic Principles of PA Mixing . . . . . . . . . . . . . . . . . 3
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connections and Connectors . . . . . . . . . . . . . . . 6
Fault Finding Guide . . . . . . . . . . . . . . . . . . . . 9
Getting to know your console . . . . . . . . . . . . . . . . 10
Facilities . . . . . . . . . . . . . . . . . . . . . . . . . 10
Input Channel . . . . . . . . . . . . . . . . . . . . . . 10
Stereo Sections . . . . . . . . . . . . . . . . . . . . . . 15
Group Sections . . . . . . . . . . . . . . . . . . . . . . 17
Master Section . . . . . . . . . . . . . . . . . . . . . . 18
Using your SPIRIT LIVE 4Console . . . . . . . . . . . . . 20
Initial Set Up . . . . . . . . . . . . . . . . . . . . . . . 20
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Public Address . . . . . . . . . . . . . . . . . . . . . . 22
Recording . . . . . . . . . . . . . . . . . . . . . . . . . 24
Care of your mixer . . . . . . . . . . . . . . . . . . . . . . 25
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selectable Options . . . . . . . . . . . . . . . . . . . . . . 27
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 29
Front Panel Layout . . . . . . . . . . . . . fold out rear cover
Block Diagram . . . . . . . . . . . . . . . . . inside rear cover
Pa g e 1
Download from Www.Somanuals.com. All Manuals Search And Download.
I N TRO D UC TI O N
Congratulations on your purchase of a SPIRIT LIVE 4mixer.
Owning a Soundcraft console brings you the expertise and
support of one of the industry’s leading manufacturers and
the results of over 20 years experience supporting some of the
biggest names in the business.
Designed by engineers who understand the individual needs
of musicians, SPIRIT LIVE 4 has been built to the highest
standards using quality Japanese components and employing
automated assembly techniques beyond the reach of most
manufacturers of compact mixers.
A rugged steel chassis is combined with moulded side trims
to give protection and distinctive appearance. Custom
moulded controls, designed for the best ‘feel’ and visual
clarity complement the styling, resulting in
a
truly
professional product which is ideal for both touring and fixed
PA installations.
SPIRIT LIVE 4is available in 12, 16, 24 and 32 channel frame
sizes, and the 12 and 16 channel sizes may be extended by
adding an 8 channel Expander. The Expander can be attached
quickly and securely to the console, requiring only a
screwdriver to complete the installation.
SPIRIT LIVE 4 incorporates circuit technology identical to
that used on some of the most sophisticated Soundcraft
consoles. The input channels are able to accept a wide range
of Microphone and Line level signals from separate input
sockets. Every channel features wide range gain control and
Line input pad, 3-band Equalisation with swept Mid and LF
range, plus a Hi-Pass Filter, 5 Auxiliary Sends, PFL(Pre Fade
Listen), Peak LED, Panning to a Stereo Bus and routing in
pairs to four Output Groups. Each channel has a separate
Direct Output and is controlled by a high-quality long throw
fader.
All frame sizes are provided as standard with dedicated
stereo inputs, arranged in pairs. One pair is included on the
12 channel frame and two pairs on all other frame sizes. Each
stereo input includes a 2-band EQ and a single auxiliary send
control with switching which allows prefade or postfade
sourcing with access to three of the five Auxiliary busses. The
stereo channel signal may be routed to either the Mix output
or to Groups 1 & 2 (upper) or Groups 3 & 4 (lower).
Pa g e 2
Download from Www.Somanuals.com. All Manuals Search And Download.
The four Output Groups provide submixing to the Mix L/ R
outputs or may feed external equipment directly. Each
incorporates stereo panning and PFL monitoring or bargraph
metering and includes an external Return input for effects or
submixing from external sources.
The Master section provides master level control for the Left,
Right, Mono and Auxiliary Send busses, with separate AFL
monitoring on each Auxiliary Send and the Mono output.
The Mix L/ R and Group outputs all have insert points for the
connection of external signal processing.
Comprehensive Talkback facilities are provided, which allow
an external talkback microphone to be routed to Mix L/ R,
Groups and Auxes 1 & 2 as required. Six 12-segment, 3-colour
peak reading LED bargraph meters provide clear display of
Mix L/ R, Group and PFL signals. Pressing any PFL or AFL
switch puts the selected signal onto both sides of the
headphones output, and the right bargraph meter.
SPIRIT Live 4 is designed to be as user-friendly as possible,
but a few minutes spent reading through this manual will
help you become familiar with the product away from the
pressure of a live session, and allow you to gain full benefit
from the superb performance offered by your new mixer.
Above all, remember that your SPIRIT mixer is designed to
extend your creativity. The more you explore the controls
and the effect they have on the sound output, the more you
will appreciate how you can influence and enhance the final
sound.
BASIC PRINCIPLES O F PA M IXING
There was a time when the P.A. system and the operator
existed only to increase the overall volume of the performers,
so that they could be heard in a large room or above high
ambient noise levels. This just isn’t true any more. The sound
system and the sound engineer have become an integral part
of the performance, and the artists are heavily dependent on
the operator’s skill and the quality of the equipment.
The following introduction to the basics of mixing are
included for the benefit of those users who may not have any
significant familiarity with sound equipment, and who are
baffled by the endless jargon used by engineers and artists
alike.
Pa g e 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Th e M ix e r
As one would expect, the main purpose of the mixer is to
combine sounds, but under precise and smooth control. This
is why long-throw faders are essential on any professional
product. The faders provide you with clear and instinctive
control of the final sound balance and like an artist playing an
instrument you should listen to the effect of your fader
movements, not look at your hands.
You r SPIRIT LIVE 4 mixer accepts a wide range of input
signals via a microphone input, for very low level signals, or a
line input, for higher level signals from, for instance, tape
machines, effects processors, etc.
The mixer is split into two sections. The Inputs receive, match
and process individual source signals, and distribute them at
precise mix levels to either a stereo Mix output or to one of
the Groups. The Master section allows overall level control
of all outputs, and provides monitoring of the audio signal at
many points in the mixer, either on headphones or meters.
The Equaliser controls are the most flexible and potentially
destructive feature of the mixer. They have a similar effect on
the frequency response of the input channel as the tone
controls on a hi-fi system, but with much greater precision,
and allow particular characteristics of the input signal to be
emphasised or reduced. It is very important that you become
familiar with the effect each control has on the sound and this
is best achieved by spending time listening to the effect of each
control on a well-known track played through the mixer.
The Auxiliary Sends provide a way of routing the input
signals to a number of secondary outputs, for artists foldback,
echo units or additional speaker outputs.
The Pan control adjusts the position of the input signal within
the stereo mix, and can be swept from full left, through to full
right. This allows particular artists to retain their correct
spatial position within the mix, and can be valuable for live
effects.
Pre-Fade-Listen(PFL) allows you to monitor the signal at
many points in the mixer. Pressing any PFL switch places the
signal at that particular point onto the headphones and the
right meter, to check the quality of the signal or to pin-point
problems. Using PFL will not affect the signals on the outputs
from the desk.
Pa g e 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Each input channel and the three main outputs have an Insert
‘A’ gauge jack socket, which is a break point in the signal
path. It allows the signal to be taken out of the mixer,
through an external piece of equipment and then back into the
mixer directly after its original exit point. The Insert point is
normally bypassed by the ‘A’ gauge jack socket contacts, and
is only brought into operation when a plug is inserted.
Typical uses would include Effects Processors, Limiters,
additional Equalisers or Delay units. In addition, each
channel has a Direct output which may also be used to feed
external equipment.
The terms PRE and POST are often used in the context of
Inserts, Equalisers and Auxiliary Sends, and describe whether
that facility is placed before (Pre) or after (Post) another
particular section. This is explained further in the detailed
description of facilities.
A mixer is often judged, amongst other factors, by the amount
of Headroom available. This is a measure of the reserve
available to cope with sudden peaks in the input signal,
without distortion caused by Clipping, when the signal
becomes so high that it would exceed the power supply rail
voltages and is as a result limited. This commonly occurs
where gain settings are incorrectly set or where sources are
improperly matched to the mixer input. If the source signal is
too high, clipping and distortion results. If the signal is too
low it becomes masked by the background noise which is
present to some degree in all mixers. The diagram below
illustrates this point.
Clipped
Signal
Noise
If the signal level is too high, clipping distortion
may occur.
Signal
Noise
If the signal level is too low it may be masked
by the noise.
Pa g e 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
CONNECTIONSAND
CONNECTORS
Although this may seem a simple subject, faulty connectors and
cabling are the source of most sound system problems.
Correctly-made cables of the proper type, with the right
connectors for the job will ensure peak performance from
your system with minimum noise pick-up. The following
section will help you to connect SPIRIT LIVE 4correctly.
Two different types of audio connectors are used, 3-pin XLR
1
and ⁄4" three pole (‘A’ gauge) jacks. These are used in several
configurations as shown in the diagrams below.
Link 3
to 1
2. Ho t(+ve )
2. Ho t(+ve )
3. Co ld (-ve )
Link 3
to 1
1. Sc re e n
1. Sc re e n
1. Sc re e n
2. Ho t(+ve )
Unb a la nc e d
Unb a la nc e d
Ba la nc e d
Inp ut
Inp ut
Outp ut
3 POLE (ste re o ) JACK
2 POLE (m o no ) JACK
Se nd
Re turn
Sc re e n
Tip
Ho t(+ve )
Co ld (-ve )
Sc re e n
Le ft Sig na l
Sig na l
Ring
Rig ht Sig na l
Gro und
Sle e ve
Gro und
Tip
Sle e ve
Ring
Insert Points
Line Input
Aux Outputs
FX Returns
Headphones
Unbalanced
Output
(see text)
Direct Outputs
Pa g e 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba la nc e d a nd
Unba la nced
All channel inputs are balanced, i.e. there are separate
+ve(hot) and -ve (cold) wires for each signal plus a ground.
The design of the differential input amplifiers is such that
interference picked up on these wires is cancelled out. This is
because, since both wires are in close proximity, the same
interference will be picked up on each wire and balanced
input amplifiers will only amplify the difference between
+ve(hot) and -ve(cold). Any signal on both hot and cold (i.e.
noise) will not be amplified - this is known as common mode
rejection (CMR). Balanced inputs should always have both
+ve and -ve connected or if only an unbalanced source, the
-ve pin shorted to ground.
Note: many modern audio/ musical instruments have
electronically balanced outputs which should not be
unbalanced by shorting one wire to ground. Always use your
inputs balanced where possible.
The Mix L/ R and Mono outputs, Group and Auxiliary
outputs are ground compensated and provide a very effective
way of optimising noise immunity, without the cost and
complexity of balanced outputs. These outputs employ
ground compensation techniques to cancel out the effects of
variation in ground potential between the mixer and other
equipment which would otherwise show up as hum. If the
output is driving a device or amplifier that has an unbalanced
input, connect the -ve(cold) signal to the ground at the
destination, not at the output of your SPIRIT LIVE 4console.
Pola rity
You will probably be familiar with the concept of polarity in
electrical signals and this is of particular importance to
balanced audio signals. Just as a balanced signal is highly
effective at cancelling out unwanted interference, so two
microphones picking up the same signal can cancel out, or
cause serious degradation of the signal if one of the cables has
the +ve and -ve wires reversed. This phase reversal can be a
real problem when microphones are close together and you
should therefore take care always to connect pins correctly
when wiring audio cables.
Grounding and Shielding For optimum performance it is vital that all signals are
referenced to a solid, noise-free earthing point and that all
signal cables have their screens connected to ground. To
avoid earth ‘loops’, use balanced connections where possible
and ensure that all cable screens and other signal earths are
connected to ground only at their source and not at both ends.
Pa g e 7
Download from Www.Somanuals.com. All Manuals Search And Download.
UNBALANCED
✗
+
-
+
-
Source
Device
Mixer
Ground loop
through screen
and chassis
BALANCED INPUT
✓
+
-
+
-
GND
Source
Device
Mixer
If the use of unbalanced connections is unavoidable, you can
mimimise noise by following these wiring guidelines:
•
•
On INPUTS, unbalance at the source and use a twin,
screened cable as though it were balanced. (see below)
On OUTPUTS, connect the signal to the +ve output pin,
and the ground of the output device to -ve. If a twin
screened cable is used, connect the screen only at the mixer
end. (see below)
+
+
-
GND
Source
Device
Mixer
INPUT
+
-
+
GND
GND
Output
Device
Mixer
OUTPUT
Avoid running audio cables or placing audio equipment,
close to thyristor dimmer units or power cables.
Noise immunity is improved significantly by the use of low
impedance sources, such as good quality professional
microphones or the outputs from most modern audio
equipment. Avoid cheaper high impedance microphones,
which may suffer from interference over long cable runs, even
with well-made cables.
Pa g e 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault Finding Guide
Repairing a sound mixing console requires specialist skills, but
basic Fault Finding is within the scope of any user if a few
basic rules are followed.
•
•
•
Get to know the Block Diagram of your console (see inside
rear cover)
Get to know what each component in the system is
supposed to do.
Learn where to look for common trouble spots.
The Block Diagram (see inside rear cover) is a representative
sketch of all the components of the console, showing how
they connect together and how the signal flows through the
system. Once you have become familiar with the various
component blocks you will find the Block Diagram quite easy
to follow and you will have gained a valuable understanding
of the internal structure of the console.
Each Component has a specific function and only by getting
to know what each part is supposed to do will you be able to
tell if there is a genuine fault! Many ‘faults’ are the result of
incorrect connection or control settings which may have been
overlooked.
Basic Troubleshooting is a process of applying logical
thought to the signal path through the console and tracking
down the problem by elimination.
•
•
Swap input connections to check that the source is really
present. Check both Mic and Line inputs.
Eliminate sections of the channel by using the insert point
to re-route the signal to other inputs that are known to be
working.
•
•
Route channels to different outputs or to auxiliary sends to
identify problems on the Master section.
Compare a suspect channel with an adjacent channel
which has been set up identically. Use PFL and AFL to
monitor the signal in each section.
Pa g e 9
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT
GETTING TO KNOW YOURCONSOLE
Refer to the fold-out front panel diagram which shows the
control functions on the SPIRIT LIVE 4. Each facility is
described below, and is identified by the reference number.
FAC ILITIES
1.
INPUTCHANNEL
MICROPHONE INPUT
The Microphone input is via a standard female XLR-3
connector and is available when the LINE -20dB switch is
released. It is designed to accept a wide range of balanced or
unbalanced low impedance input signals.
+48V Phantom Power is available on each input microphone
socket. This is switched on globally from the power supply in
the case of the 12, 16 and 24 channel desks, or from a rocker
switch adjacent to the d.c. power connector at the top right of
the 32 channel desk. Should you wish to configure inputs
without +48V power, see Selectable Options on Page 27 for
details of this modification.
Transformer-coupled dynamic microphones may be used
without causing damage, even when the +48V power is
connected, but care must be taken when using unbalanced
sources, because of the voltage present on pins 2 and 3 of the
XLR connector. Microphone input level is set by the GAIN
control(6).
NOTE: Phantom powered mics should not be plugged in
with the +48V switched on. Also you should be aware that
some microphones draw an unusually large current which
may overload the power supply, resulting in distortion.
Consult your microphone supplier for guidance if necessary.
2.
DIRECT OUTPUT
A ground compensated DIRECT output is provided, fed from
the output of the fader buffer, which is therefore unaffected
by the position of the ROUTING switches or PAN control.
This provides an ideal source for external processing units,
the output of which may be brought back to the console
through the STEREO sections or group RETURNS, or to
directly send to the tracks of a tape machine for multitrack
recording. This provides as many Tape Sends as there are
mixer channels, without using the group or mix outputs.
Pa g e 10
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT
3.
LINE INPUT
1
The LINE Input is a 3-pole ⁄4"‘A’ gauge jack socket, to accept
balanced or unbalanced line level sources when the LINE
switch(5) is pressed. Unlike the low impedance Microphone
input, this stage presents a high impedance(>10kΩ) to the
input signal, enabling many types of instruments to be
plugged straight in without D.I. boxes or external
preamplifiers.
Line inputs will be found useful as extra Effects Returns,
where additional post-effect equalisation is required.
4.
INSERT
The INSERT is a break point in the input channel signal path.
It allows the signal to be taken out of the mixer, through an
external piece of equipment and then back into the mixer to
1
continue through to the final output. The Insert is a 3-pole ⁄4"
‘A’ gauge Jack Socket, which is normally by-passed. When a
jack plug is inserted, the signal path is broken at a point just
after the Hi-Pass Filter, but before the EQ section. The signal
from the channel appears on the TIP of the plug and is
returned on the RING. The insert point allows limiters,
compressors and other signal processing units to be added as
required to particular input channels and because it is located
PRE EQ, noise generated by the external equipment may be
reduced by a small amount of H.F. cut in the Equaliser.
5.
6.
LIN E SELEC T
The LINE switch selects Line input when pressed, and
Microphone input when released. When Line is selected the
Gain range is reduced by 20dB (see 6 below).
GAIN CONTROL
When the Microphone input is selected this control acts as a
SENSITIVITY control covering a 50dB range. Channel signal
level increases as the control is turned clockwise. When the
Line input is selected it serves as a GAIN control, with the
scaling reduced by -20dB from the printed scale. A nominal
0dB input signal will pass through at unity gain, with the
knob set at the 20dB position. Some audio equipment,
particularly that intended for domestic use, operates at a
nominal -10dBV level and an increased Gain setting will be
required.
Pa g e 11
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT
7.
HI- PA SS FILTER
Pressing this switch inserts a 12dB per octave 100Hz Hi-Pass
Filter in the signal path, immediately after the input amplifier.
This is particularly useful on live vocals, and its use is
strongly recommended, even on male vocals. It can also be
used for filtering out low frequency hum.
Frequency Response Curves of the Hi-Pass Filter
dB
HI-Pass Filter
4.0
3.0
2.0
1.0
0.0
-1.0
-2.0
-3.0
-4.0
20
100
1k
10k
20k
Frequency/Hz
8.
EQ UA LISER
The Equaliser(EQ) comprises three sections. The upper
control provides H.F.(treble) boost and cut of +/ -15dB. The
lower two pairs of knobs are arranged as a cut/ boost control
(lower knob) of +/ - 15dB, and a SWEEP(frequency) control
which determines at which frequency the boost/ cut action
will be centered. The LF sections are essentially Swept Low
Frequency controls, covering a range from 40 to 400Hz and
providing much greater flexibility than a conventional
LF(bass) control. The MID section, with a frequency range
from 250Hz to 8kHz is particularly versatile for vocals,
enabling particular characteristics of the singer to be lifted or
suppressed very precisely.
Frequency Response Curves of the Equaliser
LF Section
dB
20.0
15.0
10.0
5.0
0.0
-5.0
-10.0
-15.0
-20.0
20
100
1k
10k
20k
Frequency/Hz
Pa g e 12
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT
Frequency Response Curves of the Equaliser
MID Section
dB
20.0
15.0
10.0
5.0
0.0
-5.0
-10.0
-15.0
-20.0
20
100
1k
10k
20k
Frequency/Hz
HF Section
dB
20.0
15.0
10.0
5.0
0.0
-5.0
-10.0
-15.0
-20.0
20
100
1k
10k
20k
Frequency/Hz
9.
AUXILIARY SENDS
These controls route the input channel signal to any one or
more Auxiliary busses. These are separate from the main
outputs and can therefore provide additional outputs for
foldback, echo units or extra loudspeaker ‘fills’.
AUX 1 & 2 are derived before the channel fader(PRE FADE),
and are therefore unaffected by the fader position. This
makes them particularly suitable for foldback or monitor
feeds, which need to be controlled separately from the main
P.A. mix.
AUX 3, 4 and 5 are derived after the channel fader(POST
FADE), and therefore follow any changes in fader level. They
are normally used to drive effects processing units which are
fed back into the mixer and which must fade out with the
input channel.
AUX 2 may be altered internally to be POST FADE. Refer to
the Selectable Options section (Page 28) for a description of
this modification.
All of the Aux Sends are muted when the ON switch(12) is
released.
Pa g e 13
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT
10.
PAN
The PAN control determines the position of the signal within
the stereo mix image or may be used to route the channel
signal to particular output GROUPS as selected by the
ROUTING SWITCHES (13). Rotation fully anticlockwise
feeds the signal solely to the Left mix buss or Groups 1 and 3,
while rotation clockwise sweeps the image to the right buss or
Groups 2 and 4.
11.
PFL/ PEAK LED
When the PFL switch is pressed, the Pre-Fade signal is fed to
the headphones, where it replaces the selected source. The
PFL/AFL LED on the master section illuminates to warn that
the headphones and the meters are now responding to the
PFL/ AFL selection and the PFL LED on the input channel
lights to identify the active channel. This is a useful way of
listening to any required input signal without interrupting the
main mix, for making adjustments or tracing problems.
When the PFL switch is released the LED on the channel
serves as a PEAK indicator, to warn when an excessively high
signal level is present in the channel. The signal is sampled
at two points in the channel, immediately after the input
amplifier (PRE HI-PASS FILTER & PRE INSERT) and POST
EQ. The Peak LED will illuminate approximately 4dB before
clipping and therefore give warning of a possible overload
even if the peaks are removed by external equipment plugged
into the Insert.
12.
13.
ON SWITCH
The ON switch enables all outputs from the channel when
pressed, and the associated LED illuminates to show that the
channel is active.
ROUTING SWITCHES
The input channel signal may be routed to the main STEREO
MIX (L-R) or pairs of GROUP busses (1-2, 3-4), by pressing
the respective switches. These may be used in conjunction
with the PAN control (10 above) to route the channel signal
proportionately to any of the selected busses.
13.
CHANNEL FADER
This long-throw fader determines the proportion of the
channel in the mix and provides a clear visual indication of
channel level. Normal operating position is at the ‘0’ mark,
providing 10dB of gain above that point if required.
Pa g e 14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEREO
STEREO SEC TIO N S
1.
STEREO INPUTS
Each Stereo Input section comprises a pair of similar inputs.
The inputs are electronically balanced and separate jacks are
provided for the Left and Right source signals. A mono signal
may be plugged into the upper socket only for each pair to be
fed equally to left and right busses.
2.
-10 SWITCH
The input jacks are normally set to match +4dBu nominal
signal levels. Pressing the -10 switch alters the input
sensitivity to match the -10dBV signals from most Hi-Fi
systems or semi-professional tape machines allowing the
inputs to be quickly switched to match, for instance, a cassette
player for pre-show music.
3.
EQ UA LISA TIO N
Each Stereo Input is provided with a 2-band shelving EQ
section giving ±15dB boost & cut at fixed frequencies of 60Hz
and 12kHz.
Frequency Response Curves of the Equaliser
LF Section
dB
20.0
15.0
10.0
5.0
0.0
-5.0
-10.0
-15.0
-20.0
20
100
1k
10k 20k
Frequency/Hz
HF Section
dB
20.0
15.0
10.0
5.0
0.0
-5.0
-10.0
-15.0
-20.0
20
100
1k
10k 20k
Frequency/Hz
Pa g e 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEREO
4.
5.
A UX SEN D
A single control feeds a mono sum of the stereo signal to a
choice of Aux Send busses (see 5 below).
A UX SELEC TIO N
The flexibility of the Aux send control (4) is maximised by a
choice of destinations on the two Stereo sections. On the
upper section (Stereo 1) this switch routes the Aux Send to
either AUX 1 (Prefade) when released, or AUX 3 (Postfade)
when pressed. On the lower section the choice is between
AUX 1 (Prefade) when released and AUX 4 (Postfade) when
pressed.
6.
BALANCE
The BAL control sets the relative level of the Left and Right
signals. In the centre position its gain is unity. Turning the
control fully clockwise increases the Right signal by +4dB,
and totally kills the Left signal. Full anticlockwise rotation
has the opposite effect. Balance left biases the signal to the
Left buss and Groups 1 & 3, balance right to the Right buss
and Groups 2 & 4.
7.
PFL
When the PFL switch is pressed the prefade signal is fed to
the Headphones where it replaces the selected source. The
AFL/PFL LED on the Master Section illuminates to warn that
the headphones and RIGHT/PFL METER are now
responding to the PFL selection and the PFL LED on the
Stereo Section lights to identify the active source.
8.
9.
ON
Pressing this switch turns ON the feeds to the Aux Sends and
output busses. The associated LED illuminates to show that
the section is active.
ROUTING
A single Routing Switch per section provides access to Mix
L-R and Groups 1-2 or 3-4. The upper section routes between
Mix L-R with the switch released, and Groups 1-2 when
pressed. The lower section routes between Mix L-R with the
switch released and Groups 3-4 when pressed. The relative
levels of the left and right signals is controlled by the
BALance control (6).
Pa g e 16
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUP
10.
FADER
Linear faders are provided for precise and smooth level
control for each Stereo section.
GROUP SECTION
1.
2.
RETURN
A mono Return is provided to each output Group, which is
intended for use as a sub-mix from another desk or as an
effects input. The input is electronically balanced on a
1
standard ⁄4" 3-pole ‘A’ gauge jack.
INSERT
An Insert is provided for each output Group to allow external
processing equipment to be ‘inserted’ into the output path.
1
The ⁄4" 3-pole ‘A’ gauge jacks are bypassed except when a
plug is inserted.
3.
4.
RETURN LEV EL
The level of the signal at the RETURN input (1, above) is set
by a rotary control. A panel marking indicates the nominal
unity gain position.
PAN
The Group PAN control determines the position of the signal
within the stereo image which is routed to the mix L/ R busses
when L-R is pressed. Rotation fully anticlockwise feeds the
signal solely to the Left mix buss, while rotation clockwise
sweeps the image to the right.
5.
PFL
When the PFL switch is pressed, the pre-fade Group signal is
fed to the headphones and RIGHT/PFL METER where it
replaces the mix signal. The AFL/PFL LED on the master
section illuminates to warn that the headphones and meter
are now responding to the AFL/ PFL selection and the PFL
LED on the Group lights to identify the active Group.
6.
GROUP FADER
Long throw faders are provided for each Group with unity
gain at the top of their travel.
Pa g e 17
Download from Www.Somanuals.com. All Manuals Search And Download.
M A STER
7.
8.
GROUP OUTPUT
The Group outputs are driven by ground compensated
amplifiers to a standard ⁄4" 3 pole ‘A’ gauge jack socket.
1
M A STER SEC TIO N
D.C. POWER SOCKET
The cable from the power supply connects to the console via
this 5-pin socket.
Ensure that you always use the correct power supply for your
console. The 12, 16 and 24 channel frame sizes require the
DCP100 power supply and the 32 channel frame uses the
CPS150 power supply.
9.
MONO OUTPUT
The ground compensated MONO output is a sum of the
postfade Mix Left and Right outputs, providing a separately
controlled feed which may for instance be used to drive a
centre loudspeaker cluster via a suitable power amplifier.
10.
11.
MIX L & R OUTPUTS
The MIX L & R outputs are standard male XLR-3 connectors,
driven by ground compensated amplifiers.
INSERTS
These are similar to the Input Channel Inserts and allow
external processing equipment to be ‘inserted’ into the output
1
signal path. The ⁄4" 3 pole ‘A’ gauge jack sockets are
by-passed except when a plug is inserted.
12.
BARG RAPH M ETERS
Six 12-segment, three colour bargraph meters provide visual
monitoring of the levels of the Mix Left and Right, and Group
outputs. All the meters are peak reading.
Normally the Left and Right meters show the level of the Mix
Left and Right outputs. If any PFL or AFL switch is activated
the left meter is turned off and the right meter displays the
level of the selected PFL or AFL signal.
The bargraphs may be calibrated by trimmers accessed via
holes in the panel below each meter. Adjustments may be
made using a small screwdriver, taking care not to damage
the trimmers.
Pa g e 18
Download from Www.Somanuals.com. All Manuals Search And Download.
M A STER
13.
MONO
The level of the MONO output (9) is set by a rotary fader.
The associated AFL switch with indicating LED monitors the
final output after the fader.
14.
15.
16.
AUXILIARY MASTERS
Each of the Auxiliary Send busses is provided with a rotary
master level control and an AFL switch with indicating LED
which monitors the final output after the fader.
AUXILIARY OUTPUTS
The Auxiliary Send outputs are driven by ground
compensated amplifiers to a standard ⁄4" 3 pole ‘A’ gauge
jack socket.
1
TALKBACK
A female XLR-3 connector provides the input for a headphone
mounted, gooseneck or floating dynamic microphone for
TALKBACK to selected outputs. Level is set by the TB
control and three switches route the signal selectively to Mix
L-R, Groups (GRPS) or AUX 1-2.
17.
HEADPHONE VOLUME
This control sets the level of the PHONES output at the socket
below the front armrest. Normally this is fed by the Mix L/ R
output, unless an AFL or PFL switch is pressed, in which case
the Mix signal is replaced by the AFL/ PFL signal and the
AFL/PFL LED lights to show that the AFL/ PFL system is
active.
Note that due to the way that the ground compensated
outputs operate, it is possible that a hum might be audible
under AFL listening, which is in fact cancelled on the actual
output. This would indicate that there is a ground loop in
your system which you may wish to correct.
18.
MIX FADERS
Master faders for Left and Right mix outputs. Unity gain is at
the top of their travel.
Pa g e 19
Download from Www.Somanuals.com. All Manuals Search And Download.
USING YOUR SPIRIT LIVE 4 CONSOLE
The final sound from your P.A. system can only ever be as
good as the quality of the source signal. Just as you need to
become familiar with the control functions of your mixer, so
you must recognise the importance of correct choice of inputs,
microphone placement and input channel settings. However,
no amount of careful setting up can take account of the
spontaneity and unpredictability of live performance and the
mixer must be set up to provide ‘spare’ control range to
compensate for changing microphone position and the
absorption effect of a large audience (different acoustic
characteristics from sound check to show).
The front panel drawing inside the rear cover shows
typical initial control positions which may be found a
useful guide to setting up the mixer for the first time.
Initial Set Up
The diagram on page 5 demonstrated how the matching of
input gain to the signal source was crucial to avoid distortion
at one extreme and excessive noise at the other. Set up
individual input channel as follows:
•
Connect the input required (microphone, keyboard etc.)
Note: Phantom powered mics should be connected before
the +48V is switched on.
•
•
Set Master faders at 0, input faders at 0, and set power
amplifier levels to about 70%.
Provide a typical performance level signal and press the
PFL button on the particular channel, monitoring the level
on the right-hand meter.
•
•
Adjust the input gain until the meter is just reaching the
amber section (0dB) at a typical maximum source level.
This allows sufficient headroom to accommodate peaks
and establishes the maximum level for normal operation
(but see note below).
Repeat this procedure on other channels as required. As
more channels are added to the mix, the meters may move
into the red section. Adjust the overall level using the
Master Faders if necessary.
Pa g e 20
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
If you cannot obtain a satisfactory setting, e.g. the gain
control is right at the extreme low end of the scale on
Microphone Input, try using the Line Input instead.
Listen carefully for the characteristic sound of ‘feedback’.
If you cannot achieve satisfactory input level setting
without feedback, check microphone and speaker
placement and repeat the exercise.
You are now ready to start building the mix and this should
be done progressively, listening carefully for each component
in the mix and watching the meters for any hint of overload.
If this occurs, back off the appropriate Channel Fader slightly
until the level is out of the red segments, or adjust the Master
Fader.
Note: The level of any source signal in the final output is
affected by many factors, principally the Gain control,
Channel Fader and Output Faders. You should try to use only
as much microphone gain as required to achieve a good
balance between signals, with the faders set as described
above. If the input gain is set too high, the channel fader will
need to be pulled down too far in compensation to leave
enough travel for successful mixing and there is a greater risk
of feedback because small fader movements will have a very
significant effect on output level. If the gain is set too low,
you will not find enough gain on the faders to bring the signal
up to an adequate level.
Microphone Placement Careful microphone placement and the choice of a suitable
type of microphone for the job is one of the essentials of
successful sound reinforcement. The aim should be to place
the microphone as close as physically possible to the source,
to cut out unwanted surrounding sounds, allow a lower gain
setting on the mixer and avoid feedback. Also a well-chosen
and well-placed microphone should not need any appreciable
equalisation.
Pa g e 21
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATIONS
SPIRIT LIVE 4 is designed primarily as
a
sound
reinforcement mixer, but may also be used for basic
multitrack recording. The following diagrams show typical
configurations which will illustrate how the mixer is
connected to other equipment.
Example 1 - Public
Ad dre ss - Ste re o O utp ut
In this basic set-up, an assortment of sources are connected to
the input channels, microphone to mic. inputs, and a
keyboard and guitar to line inputs. Note that some guitars
would not produce sufficient level for a direct connection, and
would require a D.I. box connected via the microphone input.
The mix L/ R outputs are connected to the power amplifier
and speakers, and a compressor/ limiter is included in the
Pa g e 22
Download from Www.Somanuals.com. All Manuals Search And Download.
output signal path via the Left and Right insert points.
Exa m p le 2: Pub lic
Ad dre ss - Ste re o
+ Centre Feed
In this second example the Group 1 Output is used to drive an
additional centre speaker, with individual fader control. The
routing on the input channels allows individual selection to
the Centre output by routing to Group 1.
Exa m p le 3: Pub lic
Ad dre ss - M ono O utp ut
In this example the console is used to feed loudspeakers in
Mono only. The compressor remains in the Left and Right
Inserts for use on these outputs if required. A feed from
another mixer is submixed to the desk on Returns 1 & 2. Note
that the Groups may be used for subgrouping channels to the
FROM
SUBMIXER
Pa g e 23
Download from Www.Somanuals.com. All Manuals Search And Download.
final output.
Exa m p le 4:
Stereo Recording
The console may also be used for 2-Track or basic multitrack
recording live or in the studio. The set up is similar to the
previous examples but with the Mix L/ R Output feeding a
2-track Tape Machine. Aux 1 is used to provide artists
foldback on headphones, and Aux 3 and 4 feed a reverb unit
2 TRACK TAPE
MACHINE
REVERB
which is returned to the console on RET1 and RET2.
Exa m p le 5:
Multitrack Recording
In this last example the mixer is connected to a multitrack
tape machines, and the main outputs to a 2-track machine for
mixdown. Once again a compressor has been included in the
insert points.
Feeds to the multitrack are taken from the channel DIRECT
outputs. Outputs from tape are fed back to the channel line
inputs and can be mixed down to the stereo mix output as
required. Aux 3 & 4 feed an effects unit as in the previous
EFFECTS PROCESSOR
Pa g e 24
Download from Www.Somanuals.com. All Manuals Search And Download.
CAREOFYOURMIXER
General Precautions
Avoid storing or using the mixer in conditions of excessive
heat or cold, or in positions where it is likely to be subject to
vibration, dust or moisture.
Keep the mixer clean using a soft dry brush, and an
occasional wipe with a damp cloth or ethyl alcohol. Do not
use any other solvents which may cause damage to paint or
plastic parts.
Avoid placing drinks or smoking materials on or near the
mixer. Sticky drinks and cigarette ash are frequent causes of
damage to faders and switches.
Regular care and inspection will be rewarded by a long life
and maximum reliability.
G lossa ry
auxiliary send
an output from the console comprising a mix of signals from
channels and groups derived independently of the main
stereo/ group mixes. Typically the feeds to the mix are
implemented on rotary level controls.
balance
clipping
the relative levels of the left and right channels of a
stereo signal.
the onset of severe distortion in the signal path, usually
caused by the peak signal voltage being limited by the
circuit’s power supply voltage.
dB (decibel)
a ratio of two voltages or signal levels, expressed by the
equation dB=20Log (V1/ V2). Adding the suffix ’u’ denotes
10
the ratio is relative to 0.775V RMS.
DI(direct injection)
the practice of connecting an electric musical instrument
directly to the input of the mixing console, rather than to an
amplifier and loudspeaker which is covered by a microphone
feeding the console.
direct output
equaliser
a post fade line level output from the input channel, bypassing
the summing amplifiers, typically for sending to individual
tape tracks during recording.
a device that allows the boosting or cutting of selected
bands of frequencies in the signal path.
Pa g e 25
Download from Www.Somanuals.com. All Manuals Search And Download.
feedback
foldback
the ‘howling’ sound caused by bringing a microphone
too close to a loudspeaker driven from its amplified signal.
a feed sent back to the artistes via loudspeakers or
headphones to enable them to monitor the sounds they are
producing.
frequency response
(sub) group
the variation in gain of a device with frequency.
an output into which a group of signals can be mixed.
headroom
the available signal range above the nominal level
before clipping occurs.
highpass filter
a filter that rejects low frequencies.
line level signals
at a nominal level of -10 to +6dBu, usually coming from a low
impedance source.
mono output
a mono sum of the left/ right mix outputs, providing a
separately controlled line level feed for additional
loudspeakers.
pan (pot)
abbreviation of ’panorama’: controls levels sent to left
and right outputs.
peaking
an equaliser response curve affecting only a band of
frequencies i.e. based on a bandpass response.
PFL (pre-fade listen)
a function that allows the operator to monitor the pre-fade
signal in a channel independently of the main mix.
rolloff
a fall in gain at the extremes of the frequency response.
shelving
an equaliser response affecting all frequencies above or
below the break frequency i.e. a highpass or lowpass derived
response.
spill
acoustic interference from other sources.
talkback
the operator speaking to the artistes or to tape via the
auxiliary or group outputs.
transient
+48V
a momentary rise in the signal level.
the phantom power supply, available at the channel mic
inputs, for condenser microphones and active DI boxes.
Pa g e 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Selectable Options
Removal of +48V on Mic Inputs
To disable the +48V phantom powering on the microphone
inputs, remove link J3 from Input PCB SC3209. This can be
done without removing the PCB as shown below, by carefully
cutting the leads of the link above the PCB at the points
marked.
To reinstate the +48V, fit a replacement link, Part No. AZ2222,
which is available from your dealer.
INPUT BOARD SC3209
JSKT1
JSKT2
JSKT3
J3
CUT
CUT
C6
C4
Edge view of PCB
C22
R19
R25
J3
Pa g e 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Reconfiguring Aux 2 as a Post Fade Send
Aux 2 is configured as a PRE FADE send at the factory, but
may be altered to be POST FADE if required by repositioning
a link on the Input PCB SC3209 as shown below.
INPUT BOARD SC3209
PRE
L10
POST
C28
C27
R56
PRE
POST
R54
R52
R48
To change AUX 2 to POST FADE, remove the PCB from the
console and carefully unsolder link J1 using the minimum of
heat to avoid the possibility of tracks lifting on the PCB.
Replace the link in position J2.
This operation should only be carried out by competent
technicians who possess the necessary soldering skills.
Pa g e 28
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEC IFIC A TIO NS
Typical Figures for a 16 Channel Console
NOISE
Measured RMS, 22Hz to 22kHz Bandwidth
Line inputs selected at unity gain and terminated 150R
MIX NOISE
Input faders down, channels routed to L-R, Pans central, Masters at maximum
Mix Left
Mix Right
-82dBu
-82dBu
AUX NOISE
Input faders down, Aux outputs at maximum, Four Stereo sections routed to Aux 1
Aux 1
Aux 2
Aux 3
Aux 4
Aux 5
-81dBu
-84.5dBu
-84.5dBu
-84.5dBu
-84.5dBu
GROUP NOISE
Input faders down, channels routed to Groups, Pans central, Group gain at unity.
Group 1
Group 2
Group 3
Group 4
-84.5dBu
-84.5dBu
-84.5dBu
-84.5dBu
E.I.N.
Microphone Input,
Maximum Gain, terminated 150R
-127.8dBu
C RO SSTALK
Channel ON switch Isolation
> 103dB to Mix L/ R @1kHz
Max. Channel Fader Attenuation > 87dB @10kHz, > 97dB @1kHz
Routing Switch Isolation
> 87dB @10kHz, > 105dB @1kHz
> 100dB wide band
> 90dB @10kHz, > 100dB @1kHz
> 85dB @10kHz, > 90dB @1kHz
> 95dB @1kHz
Max. Master Fader Attenuation
Max. Group Fader Attenuation
Max. Aux Send Attenuation
Max. Stereo Fader Attenuation
Stereo ON switch Isolation
Stereo Routing Switch Isolation
> 100dB wide band
> 90dB @1kHz
Pa g e 29
Download from Www.Somanuals.com. All Manuals Search And Download.
DISTORTION
THD measured at +20dBu
Line Input to Mix Output
< 0.0025% @1kHz, < 0.015% @10kHz
I N PUT & O UTPUT I M PED A N C ES
Microphone Input
> 2kΩ
Line Input
> 10kΩ
75Ω
Insert Sends
Insert Returns
Outputs
10kΩ
75Ω
I N PUT & O UTPUT LEV ELS
Mic Input Maximum Level
+10dBu
+30dBu
+21dBu
+21dBu
+21dBu
Line Input Maximum Level
Mix Out Maximum Level
Mono Out Maximum Level
Aux Out Maximum Level
METERING
12 Segment LED Bargraph
Accuracy Relative to 0dB
+/ - 1dB
Pa g e 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
stereo
master
GRP 1
GRP 2
AUX 2
RET 2
INS 2
GRP 3
AUX 3
RET 3
INS 3
GRP 4
AUX 4
RET 4
INS 4
1
8
1
7
DC POWER
INPUT
STE 1
AUX 1
RET 1
INS 1
AUX 5
INS L
INS R
MIC
15
2
3
MONO
9
DIRECT
10
1
2
LINE
MIX
STE 2
4
5
INS
11
12
2
3
1
LINE
-20dB
-10
GAIN
6
7
HF
LF
HF
8
4
5
AUX
PRE
AUX1
LEFT
RIGHT
PFL
GRP 1
GRP 2
GRP 3
GRP 4
AUX3
PST
MID
6
7
8
BAL
AUX 1
AUX 2
AUX 3
AUX 4
AU X 5
MONO
PFL
14
13
16
ON
AFL
AFL
AFL
AFL
AFL
AFL
LF
L-R
1-2
10
9
TB MIC
AUX
1
9
AUX
2
RET 1
RET 2
RET 3
RET 4
TB
PRE
AUX
3
3
L - R
2
-10
AUX
4
GRPS
L - R
L - R
L - R
L - R
HF
AUX
1 - 2
AUX
5
4
5
AFL
PFL
LF
PAN
PFL
PAN
PFL
PAN
PFL
PAN
PFL
PST
PAN
17
18
PHONES
10
AUX
LEFT
RIGHT
GRP 1
GRP 2
GRP 3
GRP 4
11
PRE
AUX1
PFL
AUX4
PST
12
13
BAL
PFL
6
ON
L-R
3-4
14
stereo
master
INPUT
STEREO
GROUPS & MASTER
Download from Www.Somanuals.com. All Manuals Search And Download.
Unit C6, Hastingwood Trading Estate
35, Harbet Road, London, N18 3HU
Phone 020 8803 7400
FAX 020 8803 5060
email [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|