Spectra Laser Level QM95 User Manual

Included with the QM95: Pouch, unit, battery, user guide  
Features  
Introduction  
QM95 Quick Measure  
Distance Meter  
User Guide  
Thank you for choosing the Spectra Precision QM95 from the Trimble  
family of precision products. This easy-to-use distance measuring tool  
will allow you to measure distances quickly, accurately and reliably.  
Before using the Quick Measure, read this operator’s manual carefully.  
Included is information about operation, safety and maintenance.  
Power ON / OFF  
Measure reference  
Liquid Crystal Display  
(LCD)  
Ensure that the operating instructions are with the laser distance meter  
Measure Buton  
Clear Button  
when it is given to other persons.  
Add Button  
Batteries - Installation  
Your comments and suggestions are welcome; please contact us at:  
1. Open the battery compartment.  
2. Remove the batteries from the packaging and insert them in the tool.  
NOTE When installing batteries note the positive (+) and  
negative (-) markings on the housings  
Area Button  
Trimble Spectra Precision Division  
Subtract Button  
8261 State Route 235  
Dayton, Ohio 45424 USA  
Battery Access  
Phone:  
+1 (937) 203-4419  
+1 (800) 527-3771  
+1 (937) 482-0030  
3. Close the battery compartment cover.  
Fax:  
Side Measure  
Button  
Battery disposal - Some areas have regulations regarding the disposal  
Flip-out tab  
extension  
Protective  
of batteries. Be sure to dispose of discharged batteries properly.  
overmolding  
CAUTION: The batteries should be removed when storing the laser  
more than 30 days.  
– 2 –  
– 3 –  
– 4 –  
Quick Start Guide  
Features - LCD Detail  
Features - LCD Detail  
Icon  
Description  
Unit OFF  
Press  
Press Time Press 2  
Press Time  
Short  
Press 3  
Press Time  
Comment  
Indicates laser is activated  
Single Measure  
Short  
3rd prior measure  
3.112m  
2nd prior measure  
Previous measure  
Indicates measure reference is from back  
Indicates measure reference is from front  
12.324m  
8.235m  
Continuous Measure  
Long  
Beeps if sound is on  
Cycle front or back  
Current measure  
Unit ON  
6.507m  
Change measure  
reference  
Short  
Short  
Automatic detection of tab extension and indicates  
measure reference is from extension  
Units of measure  
Area  
Short  
Short  
More bars indicate more battery power remaining  
Flashing indicates it is time to change batteries  
Unfavorable signal conditions  
Addition  
Short  
Short  
Long  
Adds next measure  
Subtracts next measure  
Cycle on / off  
Hardware error. Switch unit on/off several time. If this  
symbol remains, contact your dealer  
Subtraction  
Sound on / off  
Temperature too high or too low  
– 8 –  
– 7 –  
Units of measure  
change  
Long  
Cycle through units  
Erase previous action  
Power on/off options  
General Operation  
Single distance measurement  
1) Switch on the laser beam by pressing the Measure Button.  
2) Point the laser dot to the surface to be measured. (Default measure  
reference is from bottom of the tool).  
3) Press the Measure Button once again. The measured distance will  
be displayed.  
4) Press the Power On/Off Button to switch off.  
1) The Quick Measure is designed to allow quick measurements by  
pressing the Measure Button to switch on the tool and activate the  
laser. In this case, measurement is accomplished when the Measure  
Button is pressed the second time.  
2) It is also possible to use the power button to switch on the tool. In  
this case, the Measure Button must be pressed once to activate the laser  
and a second time to accomplish a measurement.  
Clear previous action  
Power off  
Short  
Short  
Area  
Continuous measurement  
1) Press the measure button to turn on the unit (or the Clear button  
to clear)  
2) Press the Area button  
3) Press the Measure button to measure the first side as shown on the  
LCD screen  
1) Press and hold the Measure Button for 2 seconds to activate  
continuous measuring mode. The tool beeps during continuous  
measure mode if beeper is turned on.  
2) Press the Measure Button again to stop continuous measure. When  
continuous measure is stopped, the last valid distance measurement is  
displayed on the result line.  
4) Press the Measure button to measure the second side as shown on  
the LCD screen. The Area will be shown, along with both measures.  
Continuous measure can be useful to find the shortest distance to a  
wall or longest distance to a corner as shown.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– 10 – – 11 –  
– 9 –  
– 12 –  

Shure Headphones SRH1540 User Manual
Shure Microphone SM93 User Manual
Silvercrest Food Saver SFS 150 A2 User Manual
Sony Car Video System XVM 750WEX User Manual
Sony DVD Player S9000ES User Manual
Sony Stereo Receiver 3 289 204 423 User Manual
Sony TV VCR Combo SU GW11 User Manual
Sony Universal Remote RM LP204M User Manual
Stiga Chainsaw SP 338 User Manual
Sunrise Medical Mobility Aid C001022 User Manual