Speco Technologies Home Security System HTSD37X User Manual

SIPSD37X & HTSD37X  
37X Optical Indoor / Outdoor Speed Dome Cameras  
200 New Hightway  
Amityville, NY 11701  
631-957-8700  
Speco Technologies is constantly developing product improvements. We reserve the right to  
modify product design and specifications without notice and without incurring any obligation.  
Rev. 03082010.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTICE  
1. Read and follow all the Instructions  
Read all the safety and operating instructions before using the product.  
2. Keep this manual  
Keep this manual for reference in future.  
3. Attachments / Accessories  
Use only the attachments or accessories specified by the manufacturer.  
4. Installation  
z Do not install near any heat sources such as radiators, heat registers, stoves, or other  
appratus including amplifiers that product heat.  
z Improperly installed product may fall, cause serious injury to a child or adult and  
damage the product.  
z Do not block any ventilation holes or openings. Install in accordance with the  
manufacturers instructions.  
z Use only with the cart, stand, tripod, bracket, mounting devices, or table specified by  
the manufacturer.  
z Installation should be done only by qualified personnel and conform to all the  
instructions by the manufacturer.  
z Refer all servicing to qualified service personnel.  
z Use stainless steel hardware to fasten the mount.  
z To prevent damage from water leakage when installing a mount outdoors on a roof or  
wall, apply sealant properly around holes.  
z These servicing instructions are for use by qualified service personnel only. To reduce  
the risk of electric shock, do not perform any servicing other that contained in the  
operationg instructions unless you are qualified to do so.  
z Use only replacement parts specified by the manufacturer.  
5. Power source  
This product should be operated only from the type of the power source indicated on the  
marking label.  
37X Speed Dome Camera  
3/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTICE  
Operating  
z Before using, make sure that the power supply is properly installed.  
z While operating, if any abnormal condition or malfunction is observed, stop using the  
product immediately and then contact your local dealer.  
Handling  
z Do not disassemble or tamper with the parts inside the product.  
z Do not drop or subject the product to shock and vibration as this can damage the  
product.  
z Care must be taken when you clean the clear dome cover. Especially, scratch and dust  
will ruin the quality of the product.  
Installation and Storage  
z Do not install the product in areas of extreme temperature, which exceed the allowable  
range.  
z Avoid installing in places where radiation is present.  
z Avoid installing in places where there are strong magnetic fields and electric signals.  
z Avoid installing in places where the product would be subject to strong vibrations.  
37X Speed Dome Camera  
4/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Introduction  
Features  
Package Components  
Main Part Description  
Installation  
6
9
10  
DIP Switch Setup  
Installation with Wall Mount Bracket  
Wiring and Cabling  
Operation  
11  
14  
15  
Check Points before Operation  
Check Points for Preset and Pattern Function before  
Operation  
18  
18  
OSD Menu  
19  
19  
20  
20  
21  
22  
22  
24  
Reserved Preset (Hot Keys)  
Preset  
Swing  
Pattern  
Group  
Other Functions  
OSD Display  
OSD Menu  
Quick Programming Guide  
Main Menu  
25  
25  
26  
27  
29  
34  
37  
39  
40  
41  
44  
45  
48  
49  
Display Setup  
Privacy Zone Mask Setup  
Camera Setup  
Motion Setup  
Preset Setup  
Swing Setup  
Pattern Setup  
Group Setup  
System Initialization  
Specifications  
Dimensions  
Warranty  
37X Speed Dome Camera  
5/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION 1  
Powerful Zoom Camera & Setup Options  
z Image Sensor: Sony 1/4" Double density interline transfer CCD  
z Zoom: 37X Optical Zoom, 12X Digital Zoom  
z
z
z
Day & Night, Privacy Mask and WDR  
SNR (Super Noise Reduction) Function  
Various Focus Modes: Auto-Focus, Manual Focus, Semi-Auto Focus  
z Various Setup Options in OSD Menu.  
Powerful Pan/Tilt Functions  
z MAX. 360°/sec High Speed Pan/Tilt Motion  
z With the Vector Drive Technology, Pan/Tilt motions are accomplished along the  
shortest path. As a result, the time to target view is remarkably shortened and the  
video on the monitor is very natural.  
z With the Micro-Stepping Control Technology, the video looks very natural at high  
zoom magnification during a jog operation on a controller since the camera can be  
controlled by 0.05°/sec. Hence it is very easy to make the camera focus on desired  
target views at high zoom magnification. Additionally it is easy to make the camera  
focus on desired positions with zoom-proportional pan/tilt movement.  
Preset, Pattern, Swing, Group, Privacy Mask and More…  
z MAX. 127 Presets are programmable and each preset can have its own parameter  
values independently from the other presets.  
For an example, refer to the below table.  
Preset No.  
Preset 1  
Preset 2  
•••  
White Balance  
Auto Exposure  
•••  
Label  
Remarks  
Case A  
Case 3  
“ENTRANCE”  
“WAREHOUSE”  
Case C  
Case 5  
Preset 95  
•••  
Reserved for OSD Menu  
Preset 128  
Case K  
Case 9  
“TERRACE”  
37X Speed Dome Camera  
6/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION 1  
z MAX. 8 sets of Swing are programmable. This function is that the camera moves  
repetitively between two preset positions at programmed speeds.  
z MAX. 4 Patterns are programmable. This function is that the camera memorizes the  
path (mostly curve path) by the joystick of the controller and revives the trajectory  
operated by the joystick as closely as possible.  
z MAX. 8 sets of Group are programmable. This function is that the camera memorizes  
the combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern  
and/or Swings repetitively. A Group can be combined upto 20 functions with any of  
Preset/Pattern/Swing.  
z MAX. 8 or 4 Privacy Masks are programmable, not to intrude on any others privacy.  
PTZ(Pan/Tilt/Zoom) Control  
z With the RS-485 communication connection, MAX. 255 units of cameras can be  
connected to a single controller.  
z Pelco-D or Pelco-P protocols can be selected as a control protocol in the current  
firmware version.  
OSD(On Screen Display) Menu  
z OSD menu is provided to display the status of camera and to configure the functions  
interactively.  
z The information such as Camera ID, Pan/Tilt Angle, Direction, Alarm Input and Preset  
is displayed on screen.  
Alarm In/Out Function(Only for the models which have I/O function)  
z 3 alarm sensor inputs and 1 alarm sensor outputs are available.  
z Alarm sensor input is decoupled with photo-couplers to avoid external electric noise  
and shock perfectly.  
z Both of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and  
the signal range of the sensor input is from DC 5.0V to 12.0V for various applications.  
z The camera can be set to move to a Preset position or to run functions such as Pattern,  
Swing and Group when there are external sensor activations. Also “Post Alarm”  
function is possible, which is supposed to activate after user-defined time period and  
sequentially in succession to the action by external sensor activations.  
Reserved Presets(Hot Keys)  
z Most camera setup options can be set up easily and directly with the reserved presets  
(Hot Keys), without entering into OSD menu. For more information, refer to “Reserved  
Presets(Hot Keys)” in this manual.  
37X Speed Dome Camera  
7/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION 1  
Network Function(Only for the SIPSD37X)  
z Network functions including remote monitoring, bidirectional audio and others are  
available through IP based network such as LAN, ADSL/VDSL, and Wireless LAN. For  
more information, refer to the separated manual for IP Addressable models.  
Perfect Outdoor Environment Compatibility and Easy Installation  
z The fans and heaters are built-in in the camera for cold and hot temperature  
environment. Also idealistic mechanical design protects the camera from water and  
dust. (IP67 when installed properly with wall mount bracket only / Only for outdoor  
models)  
37X Speed Dome Camera  
8/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION 1  
Product & Accessories  
zMain Body & Surface Mount Bracket  
zDefault Accessories  
[Main Cable,Wrench]  
zAccessories forThe Models with Alarm  
zAccessories forThe IP Addressable Models  
[Crossover LAN Cable,Audio Cable,CD]  
SIPSD37X Only  
In/Out Function [I/O Cable]  
Wall Mount Brackets (Included)  
[Screws :Machine M5×15,Hex Lag #14×50]  
37X Speed Dome Camera  
9/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION 1  
Mounting Screw Hole  
Drop Prevention Spring  
Reset Switch (IP Model)  
LAN Port (IP Model)  
DIP Switch  
Audio Port (IP Model)  
Main Connector  
Sensor I/O Port (I/O Model)  
Dome Cover  
zDomeCover  
Do not detach the protection vinyl from the dome cover before  
finishing all the installation process to protect the dome cover from  
scratches or dust.  
zDIPSwitch  
Used to set up camera IDs and protocols.  
zDrop Prevention  
Spring  
This part keeps the camera from dropping during installation and  
maintenance. After install the Bracket, please, hang the spring to  
the drop prevention hook of main body as shown in picture for  
further tasks.  
zMountingScrewHole Used to assemble the main body with a bracket with screws.  
zMain Connector  
Used for the power wire, the video cable and the RS-485  
communication cable connection.  
zSensorI/OPort  
Used for the sensor in/out connection. (The sensor I/O function  
possible models only)  
zLANPort  
Used for the Ethernet connection. (IP addressable models only)  
zAudioPort  
Used for the audio in/out connection. (IP addressable models  
only)  
zResetSwitch  
Used to initialize all the network configurations to the factory  
default. (IP addressable models only) Press the button for more  
than 5 seconds to initialize the network system.  
37X Speed Dome Camera  
10/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION 2  
Before installing the camera, set up the DIP switch to configure the camera ID and the  
communication protocol.  
Camera ID Setup  
z ID numbers of cameras are set up with binary numbers.  
ON  
ON  
See the examples shown below.  
Pin  
1
1
2
2
3
4
4
8
5
6
7
8
1
2
3
4
5
6
7
8
BinaryValue  
16 32 64 128  
ex)ID=5  
ex)ID=10  
on off on off off off off off  
off on off on off off off off  
z The camera ID range is “1~255”. Camera ID must not be  
“0”!  
z The factory default of the camera ID is “1”.  
z Match the camera ID with the Cam ID setting of your DVR  
or Controller to control the camera.  
z If you are connecting a single camera to a controller,  
terminate the camera. When connecting more than one  
camera to a single controller, terminate the last camera on  
the communication line. The last camera means the camera  
farthest in cable length from the controller.  
z Note that the total length of the communication cable  
between a controller and the camera(s) on the same  
communication line must be less than 1.2Km.  
37X Speed Dome Camera  
11/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION 2  
Communication Protocol Setup  
z Select an appropriate Protocol with the DIP switch combination.  
ON  
1
ON  
Switch Mode  
Protocol  
P0  
P1  
P2  
2
3
4
(Pin 1)  
(Pin 2)  
(Pin 3)  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
PELCO-D, 2400 bps  
PELCO-D, 9600 bps  
PELCO-P, 4800 bps  
PELCO-P, 9600 bps  
Reserved  
OFF  
ON  
ON  
ON  
Others  
z Match the camera protocol with the camera protocol in the setting of  
your DVR or controller to control the camera.  
z Adjust the DIP switch after turning off the camera. If you changed the  
camera protocol by changing the DIP S/W, the change will be effective  
after you reboot the camera.  
z The factory default protocol is “Pelco-D, 2400 bps”. (HTSD37X)  
z The factory default protocol is “Pelco-D, 9600 bps”. (SIPSD37X)  
37X Speed Dome Camera  
12/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION 2  
Terminal Resistor Setup  
The terminal resistor is used for the following cases.  
ON  
ON  
z Case 1 : In case that the control cable length between a camera  
and a controller is relatively very long (1:1 Connection)  
1
2
3
4
If the communication cable length is very long, the electrical signal  
will bound in the terminal point. This reflected signal causes  
distortion of original signal. Accordingly, the camera can be out of  
control. In this case, the terminal resistor of both sides i.e. the  
camera and the controller must be set to ‘ON’ state.  
z Case 2 : In case that multiple cameras are connected to a  
controller.  
Due to similar reasons with the case 1, the terminal resister of the  
controller and the last camera must be set to ‘ON’ state. The last  
camera means the camera farthest in cable length from the  
controller. Do not turn on the terminal resistor of all the cameras on  
the same communication cable.  
Controller  
Terminal Resistor ON  
RS-485  
#1  
#2  
#n  
Terminal Resistor Terminal Resistor  
OFF OFF  
Terminal Resistor  
ON  
37X Speed Dome Camera  
13/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION 2  
Make a hole whose diameter is 30~40mm Hook up “Drop Prevention Spring” on  
on the mounting surface to pass the  
wire(s) and cable(s) through the mounting  
surface. (In case of the wiring and cabling  
through the mounting surface only) Then  
prepare the wall mount bracket. Pull the  
wire(s) and cable(s) for the system as  
below. Attach the wall mount bracket to  
the mounting surface. (Hex Lag #14×50)  
main body to prevent camera from  
unexpected drop and pull the wire(s) and  
cable(s) for the system as below.  
Line up the mold lines and assemble Screw the dome cover to the main body  
main body to mount adaptor and turn it.  
And assemble the main both with the  
camera mount adaptor with the 3 screws.  
(Machine M5×15).  
and remove the protection vinyl from the  
dome cover.  
Important Notice  
z Before starting the installation,make sure that the Camera ID and Protocol are set up properly.  
37X Speed Dome Camera  
14/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION 2  
POWER  
BNC  
INTER
LAN CABLE  
BROWSER  
MAIN CABLE  
MONITOR  
AUDIO  
CABLE  
MIC SPEAKER  
RS-485  
CONTROLLER / DVR  
I/O CABLE  
SENSOR I/O  
IR  
DOOR  
SENSOR  
SWITCH  
Port Description  
z Main Cable  
Port Pin Number (RJ45)  
Connector / Wire Color  
BNC Connector  
Signal  
Video +  
Video −  
RS-485 +  
RS-485 −  
Power +  
Power −  
1
2,4  
5
Red  
3
Yellow  
Orange  
White  
7
6,8  
z I/O Cable  
Port Pin Number (RJ25)  
Wire Color  
Blue  
Signal  
1
2
3
4
5
6
IN COM +  
IN 1 −  
IN 2 −  
IN 3 −  
OUT A  
OUT B  
Yellow  
Green  
Red  
Black  
White  
37X Speed Dome Camera  
15/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION 2  
Power Description  
z Carefully check the voltage and current capacity of the rated power. The rated power is  
indicated in the back of main unit.  
24VAC is used on the HTSD37X (AC 17V~29V, 1.5A)  
12VDC is used on the SIPSD37X (DC11V~18V, 3.0A)  
z For the DC input models, be careful with the polarity of DC power. The system should be  
permanentally damaged by wrong DC input.  
z In case that the length of the power wire is very long, there may be voltage drop and the  
syatem may not work properly. Make the length of the power wire as short as possible.  
RS-485 Communication (HTSD37X ONLY)  
z For PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple  
cameras to a single controller, RS-485 communication should be connected in parallel  
as shown below. If you are connecting a single camera to a controller, terminate the  
camera. When connecting more than one camera to a single controller, terminate the  
last camera on the communication line. The last camera means the camera farthest in  
cable length from the controller. Note that the total length of the communication cable  
between a controller and the camera(s) on the same communication line must be less  
than 1.2Km.  
CONTROLLER / DVR  
-
-
+
RS-485  
-
-
+
+
+
#1  
#2  
#n  
37X Speed Dome Camera  
16/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION 2  
Video  
z Use BNC coaxial cable only.  
Alarm Input  
Internal  
+5V~12V  
IN COM+  
IN 1-  
+
-
+
+
Sensor 1  
Sensor 3  
-
IN 3-  
-
Before connecting sensors, check driving voltages and output signal types of the sensors.  
Since output signal types of the sensors are divided into Open Collector type and  
Voltage Output type in general, the wiring must be done properly after considering  
those types.  
Signal  
Description  
IN COM+  
The electric power source to drive input circuit. Connect the (+) wire of electric  
power source to drive the Sensors to this port as shown in the above circuit.  
IN1-,IN2-,IN3-  
Connect the outputs of sensors to each port as shown in the above  
circuit.  
If you want to use Alarm Input, the types of sensors must be selected in OSD menu. The  
sensor types are divided into Normal Open and Normal Close. If wrong sensor types are  
selected, alarms should be activated reversely to sensor inputs.  
~NormalOpen Output Voltage is high state when sensor is activated  
~NormalClose Output Voltage is high state when sensor is not activated  
Relay Output  
Internal  
AC or DC  
LOAD  
OUT 1  
The maximum loads are as follows.  
Power Type  
DC Power  
MAX. 24VDC, 1A  
AC Power  
Maximum Load  
MAX. 125VAC, 0.5A  
37X Speed Dome Camera  
17/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION 3  
z Before turning on the system, check if the wire(s) and cable(s) are connected properly.  
z Check if the camera ID on the controller is properly selected. The camera ID must be  
identical to that of the target camera. The camera ID can be checked by reading the DIP  
switch of the camera or on OSD.  
z If your controller supports multi-protocols, the protocol must be changed to match to that of  
the camera.  
z Adjust the DIP switch after turning off the camera. If you changed the camera protocol by  
changing the DIP S/W, the change will be effective after you reboot the camera.  
z Since the operation method can be different by controllers, refer to your controller manual  
if the camera can not be controlled properly. The operation of this manual is based on the  
standard Pelco® Controller.  
z Check fully how to operate preset function and pattern function with your controller or DVR  
in advance to operate the camera functions when using a controller or a DVR.  
z Refer to the following table when using standard Pelco® protocol controllers.  
< Go Preset >  
< Set Preset >  
Input [Preset Number] and press [Preset] button shortly.  
Input [Preset Number] and keep pressing [Preset] button for more than 2 seconds.  
< Run Pattern > Input [Pattern Number] and press [Pattern] button shortly.  
< Set Pattern >  
Input [Pattern Number] and keep pressing [Pattern] button for more than 2 seconds.  
z If your controller or DVR has no pattern button or function, use the Hot Keys with preset  
numbers. For more information, refer to “Reserved Presets(Hot Keys)” in this manual.  
37X Speed Dome Camera  
18/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION 3  
z
z
Function  
Entering into OSD  
With OSD menu, the system can be properly configured for each  
application.  
Go Preset [95]  
z Description  
Some Preset numbers are reserved to change some parameters without entering  
into OSD menu.  
z Hot Keys  
Go Preset [95]  
:Entering into OSD menu  
Go Preset [131~134] :Running Pattern Function 1 ~ 4  
Go Preset [141~148] :Running Swing Function 1 ~ 8  
Go Preset [151~158] :Running Group Function 1 ~ 8  
Go Preset [161]  
Set Preset [161]  
Go Preset [167]  
Set Preset [167]  
Go Preset [170]  
Go Preset [171]  
Go Preset [174]  
Go Preset [175]  
Go Preset [176]  
Go Preset [177]  
Go Preset [178]  
Go Preset [179]  
Go Preset [190]  
Go Preset [191]  
Go Preset [192]  
Go Preset [193]  
Go Preset [194]  
:Turning off Relay Output  
:Turning on Relay Output  
:Setting Zoom Proportional Function to ON  
:Setting Zoom Proportional Function to OFF  
:Setting Camera BLC/WDR Mode to OFF  
:Setting Camera BLC/WDR Mode to ON  
:Setting Camera Focus Mode to AUTO  
:Setting Camera Focus Mode to Manual  
:Setting Camera Focus Mode to SEMI-AUTO  
:Setting Day & Night Mode to AUTO  
:Setting Day & Night Mode to NIGHT  
:Setting Day & Night Mode to DAY  
:Setting OSD Display Mode to AUTO (Except Privacy Mask)  
:Setting OSD Display Mode to OFF (Except Privacy Mask)  
:Setting OSD Display Mode to ON (Except Privacy Mask)  
:Setting all Privacy Mask Display to OFF  
:Setting all Privacy Mask Display to ON  
37X Speed Dome Camera  
19/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION 3  
Function  
z
MAX. 127 positions are programmable. The Preset number can be  
assigned from 1 to 128 except 95. Preset 95 is reserved for entering  
into OSD menu. Camera parameters such as White Balance, Auto  
Exposure and others can be set up independently and each preset  
can have its own parameter values independently from the other  
persets. When setting up presets with a controller, Label should be  
blank and "Camera Adjust" should be set to "GLOBAL" as the  
default.To change the parameters, enter into OSD menu.  
z
z
z
Setting Presets  
Running Presets  
Deleting Presets  
Set Preset [1~128]  
Go Preset [1~128]  
To delete Presets, enter into OSD menu.  
z Function  
This function is that the camera moves repetitively between two  
preset positions at programmed speeds. When a swing function  
runs, the camera moves from the preset assigned as the 1st point to  
the preset assigned as the 2nd point in CW(Clockwise) direction.  
Then the camera moves from the preset assigned as the 2nd point to  
the preset assigned as the 1st point in CCW(Counterclockwise)  
direction.  
n
o
i
t
c
e
2nd Preset  
r
i
D
CW  
1
n
o
i
t
c
e
r
i
D
CCW  
2
1st Preset  
In case that the preset assigned as the 1st point and the preset  
assigned as the 2nd point are same, the camera turns on its axis by  
360° in CW(Clockwise) direction and then it turns back on its axis by  
360° in CCW(Counterclockwise) direction. The Swing speed is  
defined from 1°/sec to 180°/sec.  
z
z
Setting Swings  
To set Swing, enter into OSD menu.  
Running Swings  
Method 1) <Run Pattern> [Swing NO.+ 10] ex) Run Swing 3 :<Run Pattern> [13]  
Method 2) <Go Preset> [Swing NO.+ 140] ex) Run Swing 3 :<Go Preset> [143]  
z
Deleting Swings  
To delete Swings, enter into OSD menu.  
37X Speed Dome Camera  
20/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION 3  
z Function  
This function is that the camera memorizes the path (mostly curve  
path) by the joystick of the controller and revives the trajectory  
operated by joystick as closely as possible.  
MAX.  
4
Patterns are programmable and Maximum 1200  
communication commands can be programmed in a pattern.  
A Pattern can be created by the following methods.  
Method 1) <Set Pattern> [Pattern NO.]  
z Setting Patterns  
{ The Pattern programming window appears on the monitor as  
below.  
EDIT PATTERN 1  
[NEAR:SAVE /FAR:DELETE]  
0/0/x1/N  
{ The movement by Joystick and the preset movement can be  
memorized in a pattern.  
{ After a pattern is programmed, the remaining storage is  
displayed in progress bar on the screen.  
{ To save the recording, press NEAR key and to cancel, press  
FAR key.  
Method 2) Programming in OSD Menu :See the section“How to use OSD Menu”.  
z
z
Running Patterns  
Method 1) <Run Pattern> [Pattern NO.]  
Method 2) <Go Preset> [Pattern NO.+ 130] ex) Run Pattern 2 :<Go Preset> [132]  
Deleting Patterns To delete Patterns, enter into OSD menu.  
ex) Run Pattern 2 :<Run Pattern> [2]  
Note) When the system memorizes Patterns, the commands are stored in the momories, not  
the positions of Pan/Tilt/Zoom. Hence there might be small differences between the original  
path and the revived path by path type of Patterns. Note that it is not a problem in position  
precision.  
37X Speed Dome Camera  
21/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION 3  
Function  
z
This function is that the camera memorizes the combination of  
Presets, Pattern and/or Swings sequently and runs Presets, Pattern  
and/or Swings repetitively. MAX. 8 sets of Group are programmable.  
Each group can have MAX. 20 actions which are the combination of  
Preset, Pattern and Swing. Preset speed can be set up and the repeat  
number of Pattern & Swing can be set up in Group setup. Dwell time  
between actions can be set up also.  
Dwell Time  
Preset 1  
Pattern 1  
Swing 1  
Max 20 Entities  
z
z
Setting Groups  
Running Groups  
To set Groups, enter into OSD menu.  
Method 1) <Run Pattern> [Group NO.+ 20] ex) Run Group 7 : <Run Pattern>  
Method 2) <Go Preset> [Group NO.+ 150]  
[27]  
ex) Run Group 7 :<Go Preset> [157]  
z
Deleting Groups  
To delete Groups, enter into OSD menu.  
z PowerUpAction  
This setting defines a specific activity (Preset, Pattern, Swing and  
Group) to be performed in the event that the power to the camera is  
cycled. This function enables the user to resume, after turning on  
power, the last action being executed before turning off the power.  
Most of actions such as Preset, Pattern, Swing and Group are  
available for this function but Jog actions are not available to resume.  
z AutoFlip  
In case that tilt angle arrives at the top of tilt orbit(90°), zoom module  
camera turns on its axis by 180° at the top of tilt orbit and moves to  
opposite tilt direction (180°) to keep tracing targets.  
z ParkingAction  
This feature allows the camera to begin a specified operation after a  
programmed time of inactivity. This function makes the camera  
automatically run a pre-defined action if there is no command from  
controller for a pre-defined time period. “Wait Time” means how  
long a camera should wait for from the previous-last (most recent)  
command before running the pre-defined action. It can be set to 1  
second ~ 3 hours.  
37X Speed Dome Camera  
22/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION 3  
z AlarmInput  
3 Alarm Inputs are available. When external sensors activate, the  
camera runs pre-defined actions such as Preset, Pattern, Swing and  
Group. After the pre-defined time period passed, “Post Alarm”  
activates, which is pre-defined. Note that only the latest alarm input  
is effective when multiple sensors are activated at the same time.  
z PrivacyZoneMask  
Privacy Zone Mask allows the user to program 8(or 4) rectangulars  
that can not be viewed by the operator of the system. To protect  
others’ privacy, MAX. 8(or 4) Privacy Masks can be created on the  
arbitrary position to hide objects such as windows, shops or private  
house. With the Spherical Coordinates system, powerful Privacy Zone  
Mask function is possible. A mask area will move with pan and tilt  
functions and automatically adjust in size as the lens zooms telephoto  
and wide.  
z GLOBAL/LOCAL  
WB(White Balance) and AE(Auto Exposure) can be set up  
independently for each preset. There are 2 modes, "Global" mode &  
"Local" mode. The Global mode is that WB and/or AE are/is set up  
totally and simultaneously for all presets. The Global parameter  
setup such as WB and AE can be done in "ZOOM CAMERA SETUP"  
menu. The Local mode is that WB and/or AE are/is set up  
independently or separately for each preset. The Local parameter  
setup for WB and AE can be done in each preset setup menu. Each  
Local parameter such as WB and AE activates correspondingly when  
the camera arrives at each preset position. During jog operation,  
Global WB/AE value should be applied. All Local WB/AE values do  
not change although Global WB/AE value changes. The Local mode  
has the prior to the Global mode.  
Image Setup  
z Semi-AutoFocus  
This mode automatically exchanges focus modes between Manual  
Focus mode and Auto Focus mode by operation. Manual Focus mode  
activates in preset operation and Auto Focus mode activates during  
jog operation. With Manual mode at presets, Focus data is  
memorized in each preset in advance and the camera calls focus  
data in correspondence with presets as soon as the camera arrives at  
presets. It should shorten time to get focuses. The focus mode  
automatically changes to Auto Focus mode when jog operation starts.  
37X Speed Dome Camera  
23/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION 3  
Action Title  
Preset Label  
LABEL12345  
PRESET1  
Alarm Information  
I:-2- O:1  
15/4/x1/N  
Camera ID  
CAM 1  
P/T/Z Information  
z P/T/ZInformation Displays the amount of pan from zero degree vertical, the amount of  
tilt from zero degree horizontal and current compass direction. Also  
identifies the amount of the zoom magnification.  
z CameraID  
Displays the selected Camera ID (Address).  
Identfies Actions  
z ActionTitle  
"SET PRESET xxx"  
"PRESET xxx"  
"PATTERNx"  
When Preset xxx is memorized.  
When the camera reaches Preset xxx.  
When Pattern x is in action.  
"SWG×/PRESET xxx" When Swing x is in action. Displays both of Swing  
number and Preset number.  
"UNDEFINED"  
When a undefined function is called to run  
z PresetLabel  
Displays preset labels when the camera arrives at presets.  
z AlarmInformation Displays activated alarms. This information shows current state of  
Alarm Inputs and Relay Outputs. If an Input point is ON state, it will  
show a number corresponding to each point. If an Input point is OFF  
state, '-' will be displayed.  
Example) The point 2 & 3 of inputs are ON and Output is ON, OSD will  
show as below.  
I:-23 O:1  
37X Speed Dome Camera  
24/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
z The menu items with < > always have sub-menus.  
z To go to submenus or make the cursor move to the right, press NEAR key.  
z To go to the previous-upper level menus, press FAR key.  
z To make a selection, press NEAR key  
z To cancel a selection, press FAR key  
z To move the cursor in the menu, use the joystick to the Up/Down direction or Left/Right  
direction.  
z To change a value of an item, use Up/Down of the joystick in the controller.  
z To save changes, press NEAR key.  
z To cancel changes, press FAR key.  
zSystem  
Information  
Displays the system information and  
configuration. The system setting can  
not be changed using the OSD menu  
and the information is for reference  
only.  
SPEED DOME CAMERA  
------------------------  
<SYSTEM INFORMATION>  
<DISPLAY SETUP>  
<DOME CAMERA SETUP>  
<SYSTEM INITIALIZE>  
zDisplaySetup  
Enables the user to program how labels  
are displayed on the monitor.  
zDome Camera  
Setup  
Enables the user to configure various  
functions of the camera.  
EXIT  
zSystem Initialize Initializes all system configurations and  
all data to the factory default  
parameters.  
37X Speed Dome Camera  
25/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Display setup allows you to program how labels are  
displayed on the monitor. In case of AUTO, the labels are  
displayed on the monitor when there are any changes in  
parameters.  
DISPLAY SETUP  
------------------------  
CAMERA ID  
ON  
PTZ INFORMATION  
ACTION TITLE  
PRESET LABEL  
ALARM I/O  
AUTO  
AUTO  
AUTO  
AUTO  
zCameraID  
[ON/OFF]  
Displays the selected Camera ID  
(Address).  
<SET NORTH DIRECTION>  
<PRIVACY ZONE>  
zPTZ Information [ON/OFF/AUTO]  
Displays the amount of pan from zero  
BACK  
EXIT  
degree vertical, the amount of tilt from  
zero degree horizontal and current  
compass direction. Also identifies the  
amount of the zoom magnification.  
zActionTitle  
[ON/OFF/AUTO]  
Identfies Actions.  
"SET PRESET xxx"  
"PRESET xxx"  
"PATTERN x"  
"SWG/PRESET xxx"  
"UNDEFINED"  
zPreset Label  
[ON/OFF/AUTO]  
Displays the preset labels when the  
camera arrives at presets.  
zAlarmI/O  
[ON/OFF/AUTO]  
Displays the activated alarms. This  
information shows the current state of  
Alarm Inputs and Relay Outputs. If an  
Input point is ON state, it will show a  
number corresponding to each point. If  
an Input point is OFF state, '-' will be  
displayed.  
Example) The point 2 & 3 of inputs are  
ON and Output is ON, OSD will show as  
below.  
I:-23 O:1  
37X Speed Dome Camera  
26/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Compass Direction Setup  
Move the camera to a target position and press NEAR  
button to save the direction as North. The direction is the  
reference direction to assign other compass directions.  
SET NORTH DIRECTION  
------------------------  
MOVE TO TARGET POSITION  
[NEAR:SAVE /FAR:CANCEL  
Privacy Zone Mask allows the user to program  
8
PRIVACY ZONE  
------------------------  
rectangulars that can not be viewed by the operator of the  
system. To protect privacy, MAX. 8 Privacy Masks can be  
created on the arbitrary position to hide objects such as  
windows, shops or private house. With the Spherical  
Coordinates system, powerful Privacy Zone Mask function  
is possible. A mask area will move with pan and tilt  
functions and automatically adjust in size as the lens  
zooms telephoto and wide.  
MASK NO  
1
UNDEFINED  
OFF  
CANCEL  
DISPLAY  
CLEAR MASK  
<EDIT MASK>  
BACK  
EXIT  
z Mask NO  
[1~8] or [1~4]  
Selects a Mask number to program. If the  
selected mask has already data, the  
camera moves as it was programmed.  
Otherwise,  
“UNDEFINED”  
will  
be  
displayed under the Mask number.  
z Display  
[ON/OFF]  
Sets if the mask of the selected mask  
number shows or not on the screen.  
z Clear Mask [CANCEL/OK]  
Deletes the mask data of the selected  
mask number.  
37X Speed Dome Camera  
27/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Privacy Zone Mask Area Setup  
Move your camera to an area to mask. Then a mask and the  
menu to adjust the mask size will be displayed.  
EDIT MASK 1  
------------------------  
MOVE TO TARGET POSITION  
[NEAR:SELECT/FAR:CANCEL]  
Privacy Zone Mask Size Setup  
Adjusts the mask size. Use the joystick or the arrow buttons  
of your controller to adjust mask size.  
EDIT MASK 1  
------------------------  
z ꢀꢁ (Left/Right)  
Adjusts the mask width.  
Adjusts the mask height.  
z ꢂꢃ (Up/Down)  
[ :ADJUST MASK WIDTH]  
[ :ADJUST MASK HEIGHT]  
[NEAR:SAVE /FAR:CANCEL]  
37X Speed Dome Camera  
28/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Sets the general functions of zoom camera module.  
ZOOM CAMERA SETUP  
------------------------  
z Focus Mode [AUTO/MANUAL/SEMIAUTO]  
Sets camera Focus mode.  
FOCUS MODE  
DIGITAL ZOOM  
IMAGE FLIP  
SHARPNESS  
SEMIAUTO  
ON  
OFF  
16  
{ SEMIAUTO Mode  
STABILIZATION OFF  
<WHITE BALANCE SETUP>  
<AUTO EXPOSURE SETUP>  
This mode automatically exchanges focus  
modes between Manual Focus mode and  
Auto Focus mode by operation. Manual  
Focus mode activates in preset operation  
and Auto Focus mode activates during  
jog operation. With Manual mode at  
presets, Focus data is memorized in each  
preset in advance and the camera calls  
focus data in correspondence with  
presets as soon as camera arrives at  
presets. It should shorten time to get  
focuses. Focus mode automatically  
changes to Auto Focus mode when jog  
operation starts.  
BACK  
EXIT  
z Digital Zoom [ON/OFF]  
Sets the digital zoom functions to  
ON/OFF. If this is set to OFF, the optical  
zoom function runs but the zoom function  
stops at the end of optical zoom  
magnification.  
z Image Flip  
[ON/OFF]  
Sets System Image Flip Function to  
ON/OFF. When this function is set to ON,  
flipped images always come out. When  
the camera is installed as Desktop type,  
set to ON to get proper images.  
z Sharpness  
[0-32] or [0~31]  
Sets image sharpness to enhance  
pictures.  
37X Speed Dome Camera  
29/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
z Stabilization [ON/OFF]  
Compensates image vibrations by wind  
or others. The images with vibrations are  
compensated by Digital Zoom function  
and the image resolution with this  
function should be lower than normal  
image resolution when this function is  
turned on. Also this function may not  
work properly in the following cases.  
Dark scene or Low contrast scene  
High frequency vibration  
During Pan/Tilt/Zoom/Focus moving  
During Iris/Shutter/Gain moving  
White Balance Setup  
z WB Mode  
[AUTO/MANUAL]  
Retains color balance over  
temperature range. In auto mode, this  
feature automatically processes the  
viewed image. In Manual mode, Red and  
Blue level can be set up manually.  
WB SETUP - GLOBAL  
------------------------  
a
color  
WB MODE  
RED ADJUST  
BLUE ADJUST  
AUTO  
---  
---  
z Red Adjust  
[0-255] or [10~60]  
Adjusts the picture output in the red  
range.  
BACK  
EXIT  
z Blue Adjust  
[0-255] or [10~60]  
Adjusts the picture output in the blue  
range.  
37X Speed Dome Camera  
30/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Auto Exposure Setup  
AE SETUP - GLOBAL  
------------------------  
z Backlight  
[OFF/WDR/BLC/HLC] or [OFF/BLC/HLC]  
or [ON/OFF]  
BACKLIGHT  
DAY/NIGHT  
BRIGHTNESS  
IRIS  
SHUTTER  
AGC  
SSNR  
OFF  
AUTO  
50  
AUTO  
ESC  
MIDDLE  
MIDDLE  
<AUTO>  
Sets Backlight Compensation. If a bright  
backlight is present, the subjects in the  
picture may appear dark or as  
a
silhouette.  
Backlight  
compensation  
SENS-UP  
BACK  
EXIT  
enhances objects in the center of the  
picture. The camera uses the center of the  
picture to adjust the iris. If there is a  
bright light source outside of this area, it  
will wash out to white. The camera will  
adjust the iris so that the object in the  
sensitive area is properly exposed.  
Some modles has WDR(Wide Dynamic  
Range) function, which are better function  
than BLC. HLC(High Light Compensation)  
function removes the high light in a  
limited environment such as parking  
garage.  
z Day/Night  
[AUTO/DAY/NIGHT] or  
[AUTO1/AUTO2/DAY/NIGHT]  
Sets Day&Night mode.  
There are 2 AUTO modes in ×10 model  
# AUTO1 Mode : The sensitivity to change  
a mode is fixed.  
# AUTO2 Mode : The sensitivity to change  
Night mode to Day mode is adjustable.  
The sensitivity range is 1~255. The higher  
numeric value is selected, the lower  
illumination Night mode changes to Day  
mode at. If this is set to AUTO2 mode,  
ACG is fixed to HIGH.  
z Brightness  
[0~100]  
Adjusts the brightness of the images. Iris,  
The Shutter Speed and Gain are adjusted  
automatically in correspondence with  
each numeric value.  
37X Speed Dome Camera  
31/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
zIRIS  
[AUTO/MANUAL(F1.6~F28)] or  
[AUTO/MANUAL(0~100)]  
Sets Iris to operate automatically or at a user-  
defined level. If Iris is set to Auto, Iris has higher  
priority in adjusting AE and Shutter Speed is  
fixed. Auto iris is the lens function that  
automatically opens closes the iris in response  
to changing light conditions.  
If Iris is set to Manual, Iris is fixed and Iris has  
lower priority in adjusting AE, in comparison  
with others.  
zShutterSpeed [ESC/A.Flicker/Manual(256X~1/120000 sec)] or  
[ESC/A.Flicker/Manual(128X~1/120000 sec  
Sets Shutter Speed. Shutter Speed is the duration  
of the electronic shutter. If Iris is set to Manual  
and Shutter Speed is set to ESC, Shutter Speed  
has higher priority. If Shutter Speed is set to  
A.Flicker, to remove Flicker, Shutter Speed  
should be set to 1/100 sec. for NTSC and 1/120  
for PAL.  
zAGC  
[OFF/LOW/MIDDLE/HIGH/MANUAL(5~41dB)]  
or [OFF/NORMAL/HIGH]  
Sets AGC. This setting enhances image  
brightness automatically in case that luminance  
level of image signal is too low.  
zSSNR  
[OFF/LOW/MIDDLE/HIGH]  
Sets SSNR. This setting enhances the images by  
deducting noises when the gain level of the  
mages is too high.  
zSENS-UP  
[AUTO(2~256)/OFF] or [AUTO(2~128)/OFF]  
Sets SENS-UP. This setting activates Slow Shutter  
function when luminance of image (signal) is too  
dark.  
It is possible to set up the maximum number of  
frames piled up one on another by Slow Shutter  
function.  
37X Speed Dome Camera  
32/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
WDR (Wide Dynamic Range) Setup  
WDR  
------------------------  
LIMIT  
LEVEL  
MIDDLE  
50  
z Limit  
[LOW/MIDDLE/HIGH]  
z Level  
[0~100]  
BACK  
EXIT  
HLC (High Light Compensation) Setup  
HLC  
------------------------  
LIMIT  
COLOR  
LOW  
5
z Limit  
[AUTO/MANUAL]  
When there are too bright lights, this  
function blocks light sources on images  
to have better images. For example, when  
there is a car coming to a camera at night,  
this function blocks car headlights to  
recognize its number plate.  
BACK  
EXIT  
z Color  
[0~10]  
Assigns colors of masks to block light  
sources  
37X Speed Dome Camera  
33/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Sets the general functions of Pan/Tilt motions.  
MOTION SETUP  
------------------------  
zMotion  
Lock  
[ON/OFF]  
MOTION LOCK  
PWR UP ACTION  
AUTO FLIP  
JOG MAX SPEED  
JOG DIRECTION  
FRZ IN PRESET  
OFF  
ON  
ON  
120/SEC  
INVERSE  
OFF  
If Motion Lock is set to ON, it is impossible to  
set up and delete Preset, Swing, Pattern and  
Group. It is possible only to run those  
functions. To set up and delete those functions,  
enter into OSD menu.  
<PARKING ACTION SETUP>  
<ALARM INPUT SETUP>  
BACK  
EXIT  
zPower Up [ON/OFF]  
Action  
Refer to Other Functions" section.  
zAutoFlip [ON/OFF]  
Refer to Other Functions" section.  
zJog Max  
[1°/sec ~360°/sec]  
Speed  
Sets the maximum jog speed. Jog speed is  
inversely  
proportional  
to  
the  
zoom  
magnifications. As the zoom magnification  
goes up, the pan/tilt speed goes down.  
zJog  
[INVERSE/NORMAL]  
Direction Sets the Jog Direction. If this is set to  
Inverse, the view direction in the screen is  
same as the direction of joystick. If this is set  
to Normal, the view direction in the  
screen is the reverse dirction of joystick.  
zFreeze  
[ON/OFF]  
in Preset Sets Frame Freeze Function. This feature  
freezes the scene on the monitor when going  
to a preset. At the start point of a preset  
movement, a camera starts freezing the image  
of the start point. Camera keeps displaying  
the image of the start point during preset  
movement and does not display the images  
which camera gets during preset movement.  
As soon as camera stops at preset end point,  
camera starts displaying live images which it  
gets at the end preset point. This feature also  
reduces bandwidth when working with digital  
systems or digital network systems.  
This function availability should be different  
by models.  
37X Speed Dome Camera  
34/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Parking Action Setup  
This feature allows the camera to begin a specified action  
after a programmed time of inactivity.  
PARKING ACTION SETUP  
------------------------  
PARK ENABLE  
WAIT TIME  
PARK ACTION  
OFF  
00:10:00  
HOME  
z Park Enable [ON/OFF]  
If Park Enable is set to ON, the camera  
runs an assigned function automatically if  
there is no PTZ command during the  
programmed "Wait Time".  
BACK  
EXIT  
z Wait Time  
[1~59 sec. / 1~180 min.]  
Wait Time can be programmed from 1  
second to 180 minutes.  
z Park Action [HOME/PRESET/PATTERN/SWING/GROU  
P/PREV ACTION]  
This feature defines the activity when the  
camera parks. If Park Action is set to  
HOME, the camera moves to the home  
position which is memorized when the  
system boots. If Park Action is set to  
PREV. ACTION, the camera runs the  
previous action which it ran most recently.  
37X Speed Dome Camera  
35/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Alarm Input Setup  
Defines Alarm Function. When an alarm is receive, an  
input signal to the camera triggers the user-defined action  
programmed for the alarm.  
ALARM INPUT SETUP  
------------------------  
ALARM NO.  
1
z Alarm No  
[1~3]  
TYPE  
ACTION  
HOLD TIME  
POST ACTION  
N.OPEN  
NOT USED  
ENDLESS  
HOME  
Selects a sensor number to set up.  
z Type  
[Normal OPEN/Normal CLOSE]  
Selects sensor operation type.  
BACK  
EXIT  
z Action  
[NOT  
USED/PRESET/PATTERN/SWING/GROUP]  
Selects an action to run when a sensor  
signal is input.  
z Hold Time [ENDLESS / 1~59 SEC. / 1~180 MIN.]  
Sets the time period for the action which is  
run by external sensor activation. After the  
time period passes, the action pre-defined  
in Post Actionruns sequentially in  
succession to the action by external sensor  
activation. If this option is set to  
ENDLESS, Post Actiondoes not  
activate.  
z Post Action [HOME/PRESET/PATTERN/SWING/GROUP  
/PREV ACTION]  
Selects the action that a camera will run  
after the time period inHOLD TIME”  
passes. If Post Action is set to PREV.  
ACTION, the camera runs the previous  
action which it ran most recently.  
37X Speed Dome Camera  
36/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
zPreset  
Number  
[1~128]  
PRESET SETUP  
------------------------  
Selects a preset number to set up. If a  
selected preset is already defined, the  
camera moves to the pre-defined position  
and preset parameters such as Label and  
CAM Adjust show on the monitor. If a  
PRESET NO.  
1
CLR PRESET  
<EDIT SCENE>  
CANCEL  
<EDIT LABEL> LABEL123  
OFF  
GLOBAL  
RELAY OUT  
CAM ADJUST  
selected  
preset  
is  
not  
defined,  
“UNDEFINED” shows on the monitor.  
BACK  
EXIT  
zClear  
[CANCEL/OK]  
Preset  
Deletes the data of the selected Preset.  
zEdit  
Re-defines the scene position of the  
selected Preset.  
Preset Scene  
zEdit  
Preset Label  
Edits the label of the selected Preset to  
show on the monitor when the preset runs.  
MAX. 10 alphanuberic characteristics are  
allowed.  
zRelayOut  
Defines the relay output.  
zCAMAdjust [GLOBAL/LOCAL]  
WB(White Balance)  
and  
AE(Auto  
Exposure) can be set up independently for  
each preset. There are 2 modes, "Global"  
mode & "Local" mode. The Global mode is  
that WB and/or AE are/is set up totally and  
simultaneously for all presets. The Global  
parameter setup such as WB and AE can  
be done in "ZOOM CAMERA SETUP" menu.  
The Local mode is that WB and/or AE  
are/is set up independently or separately  
for each preset. The Local parameter setup  
for WB and AE can be done in each preset  
setup menu. Each Local parameter such as  
WB and AE activates correspondingly  
when the camera arrives at each preset  
position. During jog operation, Global  
WB/AE value should be applied. All Local  
WB/AE values do not change although  
Global WB/AE value changes. The Local  
mode has the prior to the Global mode.  
37X Speed Dome Camera  
37/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Preset Scene Setup  
1
EDIT SCENE - PRESET 1  
------------------------  
Use the Joystick to move the camera to a desired  
position.  
2
Save the preset position by pressing NEAR key.  
3
Press FAR key to cancel targeting the preset position.  
MOVE TO TARGET POSITION  
[NEAR:SAVE /FAR:CANCEL]  
Preset Label Setup  
Edit the label of the selected preset to show on the  
monitor when camera arrives at the preset. In the Edit  
Label menu, the dark rectangular is the cursor. As soon as  
finishing selecting an alphabet or a number, the cursor  
moves to the next digit.  
EDIT LABEL - PRESET 1  
------------------------  
[
]
----------  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZabcd  
efghijklmn  
opqrstuvwx  
yz<>-/:.  
OK  
CANCEL  
[
]
Current Cursor Position  
With Left/Right/Up/Down of the joystick, move to a  
----------  
desired Alphabet or  
a
desired number in the  
Alphanumeric set. To select a desired Alphabet or a  
desired number, press the NEAR key.  
----------  
1234567890  
ABCDEFGHIJ  
KLMNOPQRST  
UVWXYZabcd  
efghijklmn  
opqrstuvwx  
yz<>-/:.  
----------  
Space Char. Back Space Char.  
If you want to use a blank, select the double quotation  
mark (" "). If you want to delete an Alphabet or a  
number, use the back space character (" ").  
If you complete the Label editing, move the cursor to  
"OK" and press the NEAR key to save the completed  
label. To abort the current change, move the cursor to  
"Cancel" and press the NEAR key.  
37X Speed Dome Camera  
38/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
zSwing  
Number  
[1~8]  
SWING SETUP  
------------------------  
Selects a Swing number to edit. If the  
selected Swing is not defined, "NOT USED"  
is displayed in the 1st Position and the 2nd  
Position.  
SWING NO.  
1ST POS.  
2ND POS.  
1
NOT USED  
NOT USED  
SWING SPEED  
CLEAR SWING  
RUN SWING  
30/SEC  
CANCEL  
z1st Position  
2nd Position  
[PRESET 1~128]  
Sets the 2 positions for a Swing function. If  
the selected preset is not defined,  
"UNDEFINED" is displayed as shown  
below.  
BACK  
EXIT  
SWING SETUP  
------------------------  
SWING NO.  
1ST POS.  
2ND POS.  
1
PRESET5  
NOT USED  
UNDEFINED  
When a swing function runs, the camera  
moves from the preset assigned as the 1st  
point to the preset assigned as the 2nd  
point in CW(Clockwise) direction. Then  
the camera moves from the preset  
assigned as the 2nd point to the preset  
assigned as the 1st point in CCW  
(Counterclockwise) direction. In case that  
the preset assigned as the 1st point and the  
preset assigned as the 2nd point are same  
or only 1 Preset position is assigned, the  
camera turns on its axis by 360° in CW  
direction and then it turns on its axis by  
360° in CCW direction.  
zSwing  
[1°/sec. ~180°/sec.]  
Speed  
Defines Swing speed between the 2 Preset  
positions from 1°/sec to 180°/sec  
zClearSwing [CANCEL/OK]  
Deletes the data of the selected Swing.  
zRunSwing  
Runs Swing for the test purposes to check  
if it works properly.  
37X Speed Dome Camera  
39/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
zPatternNumber [1~4 ]  
PATTERN SETUP  
------------------------  
Selects a Pattern number to edit. If the  
selected  
defined,  
pattern number is not  
will be  
PATTERN NO.  
1
UNDEFINED  
CANCEL  
"UNDEFINED"  
CLR PATTERN  
RUN PATTERN  
<EDIT PATTERN>  
displayed under the selected pattern  
number.  
zClear Pattern  
[CANCEL/OK]  
Deletes the data of the selected pattern.  
BACK  
EXIT  
zRunPattern  
Runs the Pattern for the test purposes to  
check if it works properly.  
z Edit Pattern  
Edits the selected pattern.  
Pattern Edit  
With the Joystick of your controller, move the camera to  
the start position with an appropriate zoom  
magnafication. To start the pattern recording, press  
NEAR key. To exit, press FAR key.  
EDIT PATTERN 1  
------------------------  
MOVE TO START POSITION  
[NEAR:START /FAR:CANCEL]  
Move camera with joystick of controller or run preset  
function to memorize the path (mostly curve path) in the  
selected pattern. The movement by Joystick and preset  
movement will be memorized in a pattern. After a  
pattern is programmed, the remaining storage is  
displayed in progress bar on the screen.  
EDIT PATTERN 1  
To save the data and exit, press NEAR key. To cancel  
saving the data and delete the data, press FAR key.  
[NEAR:SAVE /FAR:DELETE]  
0/0/x1/N  
37X Speed Dome Camera  
40/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
zGroup Number [1~8]  
GROUP SETUP  
------------------------  
Selects a Group number to edit.  
GROUP NO.  
1
If the selected Group number is not  
UNDEFINED  
CANCEL  
defined,  
"UNDEFINED"  
will  
be  
CLEAR GROUP  
RUN GROUP  
<EDIT GROUP>  
displayed under the selected Group  
number.  
zClearGroup  
[CANCEL/OK]  
Deletes the data of the selected Group.  
BACK  
EXIT  
zRunGroup  
Runs the Group for the test purposes to  
check if it works properly.  
zEditGroup  
Edit the selected Group.  
Group Edit  
Press Near key when the cursor is at “NO” to start  
EDIT GROUP 1  
------------------------  
editing the selected Group.  
NO ACTION ### DWELL OPT  
------------------------  
1 NONE  
2 NONE  
3 NONE  
4 NONE  
5 NONE  
------------------------  
SAVE  
CANCEL  
[NEAR:EDIT]  
Note that MAX. 20 actions are allowed in a Group. Move  
the cursor up/down to select an Action. Press Near key  
to edit.  
EDIT GROUP 1  
------------------------  
NO ACTION ### DWELL OPT  
------------------------  
1 NONE  
2 NONE  
3 NONE  
4 NONE  
5 NONE  
------------------------  
SAVE [NEAR:EDIT ACT]  
CANCEL [FAR :EDIT END]  
37X Speed Dome Camera  
41/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
Define Action, Dwell time and Option. Note that the dark  
rectangular is the cursor. Move the cursor Left/Right to  
select an item and move cursor Up/Down to change  
each parameter.  
EDIT GROUP 1  
------------------------  
NO ACTION ### DWELL OPT  
------------------------  
1 NONE  
zAction ###  
[NONE/PRESET/SWING/PATTERN]  
2 NONE  
3 NONE  
zDWELL  
[0 SEC. ~ 4 MIN.]  
4 NONE  
5 NONE  
------------------------  
SAVE [ :MOVE CURSOR]  
CANCEL [ :CHANGE VAL.]  
Sets the Dwell Time between functions.  
zOPT  
Option. It is a preset speed when a  
preset is selected in the Action. It is the  
number of repeat when a Pattern or a  
Swing is selected in the Action.  
Edit the items such as Action, ###, Dwell and OPT by  
EDIT GROUP 1  
moving the cursor.  
------------------------  
NO ACTION ### DWELL OPT  
------------------------  
1 PRESET  
2 NONE  
3 NONE  
4 NONE  
5 NONE  
1 00:03 360  
------------------------  
SAVE [ :MOVE CURSOR]  
CANCEL [ :CHANGE VAL.]  
After finishing editing a Action, press Near key to go to  
the previous-upper level menu (Step ). Move the cursor  
Up/Down to select an Action number and repeat Step ~  
Step to keep editing the selected Group.  
EDIT GROUP 1  
------------------------  
NO ACTION ### DWELL OPT  
------------------------  
1 PRESET  
2 NONE  
3 NONE  
4 NONE  
5 NONE  
1 00:03 360  
------------------------  
SAVE [NEAR:EDIT ACT]  
CANCEL [FAR :EDIT END]  
37X Speed Dome Camera  
42/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
After finishing setting up, press FAR key to exit. Then the  
cursor will move to “SAVE”. Press Near key to save the  
data.  
EDIT GROUP 1  
------------------------  
NO ACTION ### DWELL OPT  
------------------------  
1 PRESET  
2 NONE  
3 NONE  
4 NONE  
5 NONE  
1 00:03 360  
------------------------  
SAVE  
CANCEL  
37X Speed Dome Camera  
43/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD MENU 4  
zClear All Data  
Deletes all configuration data and the system  
is set to the factory default.  
SYSTEM INITIALIZE  
------------------------  
CLEAR ALL DATA  
CLR DISPLAY SET  
CLR CAMERA SET  
CLR MOTION SET  
CLR EDIT DATA  
REBOOT CAMERA  
REBOOT SYSTEM  
NO  
NO  
NO  
NO  
NO  
NO  
NO  
zClear Display Set Initializes all the configuration data for Display.  
zClear Camera Set Initializes all the configuration data for  
Camera.  
zClear Motion Set Initializes all the configuration data for Motion.  
zClear Edit Data  
Deletes all the configuration data for Preset,  
Swing,Pattern and Group.  
BACK  
EXIT  
zReboot Camera  
zReboot System  
Reboots the zoom camera module.  
Reboots the system.  
Factory Default  
z Display Parameters  
Camera ID  
PTZ Information  
Action Title  
Preset Label  
Alarm I/O  
z Camera Parameters  
Focus Mode  
Digital Zoom  
Image Flip  
Sharpness  
Stabilization  
White Balance  
Backlight  
Day&Night  
Brightness  
Iris  
ON  
SemiAuto  
ON  
OFF  
16  
OFF  
AUTO  
OFF  
AUTO ro AUTO2  
50 or 25  
AUTO  
AUTO  
AUTO  
AUTO  
AUTO  
Pan 0°  
Undefined  
North Direction  
Privacy Zone  
Shutter  
ESC  
z Motion Parameters  
Motion Lock  
Power Up Action  
Auto Flip  
AGC  
SSNR  
SENS-UP  
MIDDLE or HIGH  
MIDDLE  
AUTO  
OFF  
ON  
ON  
Jog Max Speed  
Jog Direction  
Freeze In Preset  
Park Action  
120°/sec  
INVERSE  
OFF  
OFF  
OFF  
z User-Defined Data  
Preset 1~128  
Swing 1~8  
Pattern 1~4  
Group 1~8  
Undefined  
Undefined  
Undefined  
Undefined  
Alarm Action  
37X Speed Dome Camera  
44/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS 5  
HTSD37X / SIPSD37X  
NTSC  
Video Signal Format  
ImageSensor  
TotalPixels  
Effective Pixels  
Horizontal Resolution  
Video Signal-to-Noise  
Zoom  
Sony 1/4'' Double Density Interline Transfer CCD  
811(H)×508(V) 410K  
768(H)×494(V) 380K  
550 TV Lines(Color), 680 TV Lines(B/W)  
50 dB (AGC Off)  
37X Optical Zoom, ×12 Digital Zoom  
F1.6~3.9, f=3.5~129.5mm  
ForcalLength  
Angle ofView  
ZoomSpeed  
MinimumIlluminance  
Day & Night  
Focus  
H : 55.5°(Wide)~1.59°(Tele) / V : 42.5°(Wide)~1.19°(Tele)  
2.5 sec (Wide to Tele)  
0.7 Lux (Color) / 0. 06 Lux (B/W), 50 IRE / F1.6  
Auto / Day / Night(ICR)  
Auto / Manual / SemiAuto  
Iris  
Auto / Manual  
ShutterSpeed  
AGC  
256X ~ 1/120000 sec  
Low / Middle / High / Manual / Off  
Auto / Manual(Red, Blue Gain Adjustable. 1800°K~10500°K)  
WDR / BLC / HLC / Off  
WhiteBalance  
BLC  
Flickerless  
Selectable  
SSNR  
Low / Middle / High / Off  
Privacy Zone  
Stabilization  
8 Masks, Spherical Coordinate  
ON / OFF  
37X Speed Dome Camera  
45/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS 5  
MECHANISM PART  
360°(Endless)  
Pan  
Tilt  
Movement  
Range  
90°  
Preset  
Jog  
360°/sec.  
0.05 ~ 360°/sec. (Proportional to Zoom)  
1~ 180°/sec.  
Speed  
Swing  
Preset  
Pattern  
Swing  
127 Presets (Label, Independent Camera Parameter Setting)  
4 Patterns [1200 Commands(Approx. 5 Minute) / Pattern]  
8 Swings  
8 Groups (MAX. 20 Actions with The Combination of Preset,  
Pattern and Swing)  
Group  
Other Pan/Tilt Functions  
Communication  
Protocol  
Auto Flip, Auto Parking, Power Up Action and etc.  
RS-485 (HTSD37X ONLY)  
Pelco-D, Pelco-P Selectable  
OSD  
English, Menu / PTZ information etc  
3 Inputs, Photo-Coupler Type, DC 5V~12V  
1 Output, Relay Output, MAX. Load DC24V 1A / AC125V 0.5A  
Always ON  
Sensor Input  
Alarm Outputs  
Fan  
Heater  
Operation Start from Internal Temperature 10°C  
-22°F ~ +122°F  
Operating Temperature  
37X Speed Dome Camera  
46/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS 5  
MECHANICAL  
Ceiling Mount  
Wall Mount  
Dome  
Polycarbonate  
Material  
Internal  
Polycarbonate,ABS  
Aluminium  
External  
Dome Size  
Dimension  
Weight  
150mm / 5.9”  
EBO/EBI  
model  
192×265.3 mm  
Approx 3.2 Kg  
296×276.6 mm  
Approx 3.8 Kg  
[Note]  
1) Specification and features are subject to change without prior notice.  
2) Check the voltage and current capacity of rated power carefully.  
HTSD37X : 24VAC ONLY  
SIPSD37X : 12VDC ONLY  
37X Speed Dome Camera  
47/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS 5  
z Main Body  
155  
10  
7.  
5
z Wall Mount Type  
118.6  
80  
277.9  
4-  
8
[Unit mm]  
37X Speed Dome Camera  
48/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY 6  
37X Speed Dome Camera  
49/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
200 New Hightway  
Amityville, NY 11701  
631-957-8700  
Rev.03082010  
Speco Technologies is constantly developing product improvements.  
We reserve the right to modify product design and specifications without notice  
and without incurring any obligation.  
37X Speed Dome Camera  
50/50  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Projector XG C435X L User Manual
Shiro Telephone SB2112 User Manual
Silvercrest Bluetooth Headset SBTF 10 A1 User Manual
Sony Car Satellite TV System FWD S55H2 User Manual
Sony MiniDisc Player MDS S707 User Manual
Sony MiniDisc Player MZ E45 User Manual
Sony Network Card BRBK 301 User Manual
Sony Watch SWR50 User Manual
Stiga Lawn Mower 13 6103 19 User Manual
Sunrise Medical Mobility Aid Quickie 2 Lite User Manual