DVR4WM/8WM/16WM
Setup Guide
Speco Technologies
200 New Highway
Amityville, NY 11701
800-645-5516
Speco Technologies is constantly developing product improvements. We reserve the right to modify product
design and specifications without notice and without incurring any obligation. Rev. 11/10/09.
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Monitor
Audio Out
Call Monitor
Audio Out
Main Monitor Audio Out RCA connector is provided for the DVR to connect an audio output
device (e.g. an amplified speaker).
7
8
Call Monitor Audio Out RCA connector is provided for the DVR to connect an audio output
device (e.g. an amplified speaker).
Audio In connectors are for the DVR to connect audio source devices. For DVR-4WM, 4 RCA
Audio In connectors will be provided; whereas for DVR-8WM and DVR-16WM, a D-Sub Audio
In connector is provided.
Audio In
9
The DVR has a free voltage DC power connection jack. Please connect the power supply
adapter shipped with the unit.
Power Jack
10
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Pin Definition of Alarm I/O & RS-485, and Audio In
Alarm I/O & RS-485:
DVR-4WM:
Pin Definition
Pin Definition
Pin Definition
Pin Definition
1
2
3
4
Alarm Out Open
Alarm Out COM
RS485 D+
5
6
7
8
Alarm In 1
Alarm In 2
Alarm In 3
Alarm In 4
9
Alarm Out Close 13 GND
10 GND
11 GND
12 GND
14 GND
15 GND
RS485 D−
15pin D-sub connector I/O cable for 4TL: Speco # DVR4TLALMCBL
DVR-8WM & DVR-16WM:
Pin Definition
Pin Definition
Pin Definition
Alarm In 10
(DVR-16WM)
Alarm In 11
1
2
3
4
5
6
7
Alarm Out Open
10 Alarm In 5
19
20
21
22
23
24
25
Alarm Out COM
RS485 D+
RS485 D−
Reserved
11 Alarm In 6
12 Alarm In 7
13 Alarm In 8
14 Alarm Out Close
15 Reserved
16 Reserved
(DVR-16WM)
Alarm In 12
(DVR-16WM)
Alarm In 13
(DVR-16WM)
Alarm In 14
(DVR-16WM)
Alarm In 15
(DVR-16WM)
Alarm In 16
(DVR-16WM)
Alarm In 1
Alarm In 2
8
9
Alarm In 3
Alarm In 4
17 Reserved
18 Alarm In 9 (DVR-16WM)
25p D-sub I/O cable for 8/16TL: Speco # DVR816TLALMCBL
Audio In (DVR-8WM & DVR-16WM only):
Pin Definition
Pin Definition
10 GND
11 GND
Pin Definition
1
2
3
4
5
6
7
8
9
Audio 1
19 Audio 12 (DVR-16WM)
20 Audio 14 (DVR-16WM)
21 Audio 16 (DVR-16WM)
22 GND
23 GND
24 GND
Audio 3
Audio 5
12 GND
Audio 7
13 Reserved
14 Audio 2
15 Audio 4
16 Audio 6
17 Audio 8
18 Audio 10 (DVR-16WM)
Audio 9 (DVR-16WM)
Audio 11 (DVR-16WM)
Audio 13 (DVR-16WM)
Audio 15 (DVR-16WM)
GND
25 Reserved
25p D-sub Audio cable for 8/16TL: Speco # DVR816TLAUDCBL
Power On the DVR
Please follow the proper power on procedures to avoid damaging the DVR.
•
•
Connect all necessary components, e.g. monitor and cameras, before powering the DVR.
Check the type of power source before connecting the power adaptor to the DVR. The
acceptable power input is between AC110V ~ AC240V.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setup
Enter the OSD main menu to setup some basic configurations of the DVR. The basic configuration
must be set with the OSD on the DVR.
Enter OSD Main Menu:
•
•
•
•
Press MENU button on the remote controller to enter the OSD main menu.
Enter username and password. The default username and password is admin and 1234.
Press MENU again to quickly input the default username “admin”.
It is strongly suggested to change the password to prevent unauthorized access.
Date / Time Setting:
Follow steps below to setup date/time before the recording starts.
•
•
Select <Date/Time> in System Setup menu.
Select the date and time using LEFT/RIGHT keys; then adjust the value using UP/DOWN
keys.
•
The new date and time settings take effect after the changes are confirmed.
Language Setting:
If users wish to change language of the DVR system, follow the steps below.
•
•
Select <Language> in System Setup menu and press ENTER.
Press the UP/DOWN keys to select the desired language.
Hard Drive Format
After users have finished changing the time, they must format the drive or they will not be able to
review recorded data.
•
•
•
•
•
•
Select <Database Setup> in the System Setup and press ENTER.
Select <Internal Disks> and press ENTER.
Press ENTER on the Device Name. <None> will begin to flash.
Use the UP/DOWN keys to change <None> to <Format>.
Press ENTER again and the drives will format.
Press ESC to escape the menu when the drives have reached 100%.
Network Setup
Configure the LAN setup for the DVR to properly function with Ethernet connection.
•
•
•
From OSD main menu, select <System Setup> Æ <Network Setup>, set the <LAN Select>
item to <LAN> or <PPPoE> according to the network application, and enter <LAN Setup>.
For DHCP, set the DHCP to <ON>. The IP address, Netmask, Gateway and DNS settings are
retrieved from network servers. DHCP is dynamic and the settings change from time to time.
For Non-DHCP users, set the DHCP to <OFF>. Enter an IP address, Netmask, Gateway, and
DNS settings. Please obtain the information from the network service provider.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
To change the IP address, Netmask, Gateway and DNS value, press UP/DOWN keys to move
the cursor to the item. Use LEFT/RIGHT keys to access each section of the value and press
ENTER, then change the value using UP/DOWN keys.
•
•
PPPoE users must set the <PPPoE Account>, <PPPoE Password> and <PPPoE Max Idle>
as well.
When the settings are complete, press ENTER to confirm and save the settings; or ESC to
abort.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Dome Camera Control
Dome Camera Connection & Settings:
•
•
See section Pin Definition of Alarm I/O & RS-485, and Audio In for RS-485 port pin definition.
Connect the R+, R- terminals on the dome camera to the D+, D- terminals on the RS-485 port
by RS-485 cable respectively.
•
•
To set up dome camera’s protocol and ID, press MENU to access the OSD main menu or
change the protocol and ID by using SpecoRemote, and select <Camera Setup>. The available
protocols include <Speco>, <DSCP>, <AD422>, <Pelco D>, <Pelco P>, <Fastrax 2>, <JVC>,
<Panasonic_C>, and <Panasonic_N>. The default is <None>. Note that ID number must
match the ID address defined by the dome camera.
To configure the RS-485 parameters, select <System Setup> from OSD main menu or through
SpecoRemote, and then select <RS485 Setup>. The default RS-485 settings are 9600 Baud, 8
Data Bits, 1 Stop Bit and No Parity.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the DVR via SpecoRemote
Setup Requirements:
•
•
Make sure the PC is connected to the Internet.
Obtain IP address of the DVR-4WM/8WM/16WM. To check the DVR’s IP address, press MENU
on the remote controller and select <System Setup> Æ <Network Setup> Æ <LAN Setup> Æ
<IP> to check the IP.
Changing Internet Setting:
•
Start the IE; select <Tools> from the main menu of the browser, then <Internet Options> and
then click the <Security> tab.
•
•
Select <Trusted sites> and click <Sites> to specify its security setting.
Uncheck “Require server verification (https:) for all sites in this zone”. Type the IP address of the
unit in field and click <Add> to add this website to the zone.
•
•
In the Security Level area, click <Custom Level>. Under <ActiveX controls and plug-ins>,
set all items to <Enable> or <Prompt>.
Click <OK> to accept the settings and close the <Security Settings> screen.
Using SpecoRemote:
•
•
Start IE and enter the IP address of the DVR-4WM/8WM/16WM in the address bar.
The ActiveX controls and plug-ins dialog will show twice for confirmation; click <YES> to accept
ActiveX plug-ins. The SpecoRemote plug-ins will be downloaded and installed on the PC
automatically when the connection is successfully made.
NOTE: Do not enter any leading “0” characters in the address, for example,
“192.068.080.006” should be entered “192.68.80.6”.
NOTE: If the default trigger port 80 is changed into another one, port 81 for example,
then the IP address should be entered as “192.68.80.6:81”.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Version verification starts automatically to verify whether SpecoRemote was installed. This
process may take up to 30 seconds.
•
•
When the software is completely downloaded and installed, the Login Screen is displayed.
Enter the username and password. The default usernames and passwords are admin / 1234
and user / 4321.
The following picture shows the display window of the SpecoRemote:
Refer to the table below for brief description of functional items:
Item Description
Item Description
1
2
3
4
5
6
7
8
9
Instant Recording
10 Search Event List
11 Capture Snapshot
12 4:3 Viewing Aspect
13 HDD Status
14 Playback Control
15 Select Picture Size
16 Select Bandwidth Speed
17 Download DVRPlayer
Smooth the Image
Deflicker On/Off at Playback
Audio On/Off
Select Camera
Display Mode
View Live Camera
Playback Video
Setup Menu
For more information on SpecoRemote, see User’s Manual.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SpecoRemote Playback
Playback Remote Video:
•
•
Click <Play> on the main window toolbar, and then <Remote Playback> tab.
The <From> and <To> on top of the screen display the date and time from which recorded
video is available for playback.
•
•
Choose <Playback> in <Select> field for playback recorded video.
Select the date and time of the segment to playback from the <Start> field. The date and time
can be changed either by typing desired numbers direcWMy or using the arrow buttons.
Click <OK> to start the playback, or click <Close> to abort.
•
Playback Local *.drv File:
•
•
Click <Play> on the main window toolbar, and then <Local Playback> tab.
Click <Open> and the file selection screen is displayed. Select the *.drv video file to playback
and click <OK>.
•
•
•
Click <OK> to start the playback, or click <Cancel> to abort.
View the video playback using the Playback controls.
To end the playback, click <Live> to return to live video.
Playback Local *.avi Files:
•
Start the windows media player or other media player from <Start> menu (or any other possible
access).
•
•
Select <File> and then <Open>.
Select the wanted *.avi file, and click <Open>.
NOTE: The *.avi files for each channel are stored separately. Therefore the video can
be played back in single channel, full screen mode only.
Playback Event Video
•
•
•
Click SEARCH on the main window toolbar. The Event List appears.
Scroll through the Event List and highlight the interested events.
Double-click on the desired event to view the event video.
Playback Controls:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Mobile View Software
The DVR-4WM/8WM/16WM provides mobile surveillance software called Mobile View Software.
This allows users to monitor via a mobile device with internet connection. The Mobile View Software
for a brief introductions of installation on a JAVA mobile device and basic operations.
Download and Installation:
•
Access the java installation menu on a JAVA mobile device and connect the official website to
direcWMy download the software to the mobile device.
•
After the download has completed, follow the instruction shown on the screen of the JAVA
mobile device to installed Mobile View software.
Basic Operation:
Locate the installed Mobile View software and launch it. The main window will be shown as below.
•
•
Access <Connect to device> and users can create bookmarks for DVRs via entering
hostname/IP address, port, username, and password of the devices.
When a DVR is connected, the available functions will be listed as shown above on the right.
Users can select <Live Monitoring> to view the live video. <Normal Playback> and <Event
Playback> allow users to playback recorded normal and event videos. <Menu Config> enables
users to setup part of the DVR’s configuration.
•
<Snapshot Viewer> is where the snapshot pictures can be viewed after they are saved to the
database of the mobile devices.
Refer to Mobile View Software User’s Manual for installation on Black Berry phones and detailed
information of all functions.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Speco Technologies
200 New Highway
Amityville, NY 11701
800-645-5516
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|