Page 4
DT8 Zero Owner’s Manual
SPEAKER SPECIFICATIONS
DT8 Zero
System Description:
Two tweeters mounted onto a
dual voice coil woofer
High Frequency Drivers:
Low Frequency Driver:
Dual 1" Resin coated Silk Dome
Tweeters
8" Polypropylene Cone
Woofer with Dual Voice Coil
and Rubber Surround
Impedance:
8Ω
Frequency Adjustments:
Efficiency:
None
91dB 1w/1m
48Hz - 20kHz
80 watts (undistorted)
Frequency Response:
Power Recommendations:
Diameter x Depth:
113⁄8" x 4"
(288.925mm x 101.600mm)
93⁄4
(247.650mm)
"
Cut-Out Diameter:
In our attempt to constantly improve our products, features and specifications are subject to change without notice.
SpeakerCraft offers a variety of accessories to make your installation of these speakers and other SpeakerCraft products easy, economical,
and professional. Contact your authorized SpeakerCraft Dealer for more information. Should you have any questions regarding this, or
any other SpeakerCraft product, please call our toll-free Service Hotline at 1-800-448-0976. We are available to assist you every weekday,
except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.
940 Columbia Ave., Riverside CA 92507
USA (800) 448 0976 Fax (951) 787 8747
LIT75800(rev1)
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 2
DT8 Zero Owner’s Manual
5. Add insulation. If the area in the ceiling is not already insulated, add an
adequate amount insulation material to loosely cover the back of the
speaker. If the insulation material used is faced with foil or paper, position
the foil or paper away from the speaker.
Diagram 2
SPEAKER INSTALLATION
The unique integral four foot mounting system incorporated into your AIM DT
speaker allows for a quick installation by following these easy steps.
1. Remove the grille. It may be necessary to push one or two of the mount-
ing screws, and its attached foot, towards the baffle and against the inside
surface of the grille to force the grille out of its retaining groove.
2. Attach the speaker cable (observing the proper polarity with your amplifier,
+ to + and - to -). Either channel may be attached to either terminal set,
however, be sure that polarity (+ and -) is correct on each channel or the
performance of the speaker will be seriously affected, as one channel will
cancel out the other. (See Diagram 2)
3. Make sure the mounting feet are turned inward to clear the opening,
and insert the speaker into the ceiling. Position the speaker into the hole.
Note: The flange of the speaker is designed to flex and conform to any
small imperfections in the ceiling’s surface. Tighten the four screws on the
front of the baffle only enough to make the flange become snug against
the ceiling. As you tighten the screws, the feet will automatically flip into
an outward position thereby clamping the drywall between the feet and
the flange. (See Diagram 3)
Diagram 3
CAUTION: Over tightening may warp the baffle, crack the ceiling, cause
the flange to distort, and make the grille difficult to install.
4. Push the grille firmly into the slot in the speaker baffle.
SPEAKER ADJUSTMENT
Adjusting the Pivoting Tweeters
Once the woofer is positioned, further refinement can be made by pointing
the tweeter towards the listener. Gently pivot the tweeter to point it in the
desired direction (See Diagram 4).
Diagram 4
PAINTING THE SPEAKER
If you plan to paint your speaker, we recommend that it be done prior to
installation. If you plan to paint your speaker sometime in the future, it is
best to remove it by simply reversing the steps for “Speaker Installation” listed
above. If it is necessary to paint the speaker while it is still in the ceiling, the
paint mask provided in the carton must be installed in place of the grille while
the flange is being painted with the ceiling. The grille can also be painted,
however, great care should be taken not to clog the holes as this will greatly
reduce the sound quality of the speaker. SpeakerCraft recommends only light
spray painting using 5 parts thinning agent to 1 part paint. Do not paint the
grille while it is attached to the speaker.
Pivot the Tweeter by gently
pushing on the sides
Download from Www.Somanuals.com. All Manuals Search And Download.
DT8 Zero Owner’s Manual
LIMITED LIFETIME WARRANTY
Page 3
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and
workmanship, provided the speaker was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom
they were purchased, or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments
will be refused. It is preferable to ship this product in the original shipping container to lessen the chance of transit damage. In any case,
the risk or loss or damage in transit is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized Dealer,
it is determined that the unit was defective in materials or workmanship at any time during this warranty period, SpeakerCraft or the
SpeakerCraft Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below. If this
model is no longer available and can not be repaired effectively, SpeakerCraft, at its sole option may replace the unit with a current model
of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be required. If
mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modification. All replaced parts and
product become the property of SpeakerCraft Inc. Products replaced or repaired under this warranty will be returned to the original retail
purchaser, within a reasonable time, freight prepaid.
This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate pack-
ing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification
of the product which has not been authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration
caused by environmental conditions. This Warranty will be void if the Serial Number on the product has been removed, tampered with or
defaced.
This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the
purchaser’s sole remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental or con-
sequential damages arising out of the use or inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized Dealer
has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow
the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow
limitation on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation
does not apply.
Declaration of Conformity
We, Speakercraft Inc.
940 Columbia Ave.
Riverside, CA 92507
USA
declare under our sole responsibility that the products described in
this owners manual are in compliance with technical standards
EN 50081-2
EN 50082-2
EMC, Emission
EMC, Immunity
SpeakerCraft Inc.
940 Columbia Ave. Riverside CA 92507
(800) 448-0976 Fax (951) 787-8747
Download from Www.Somanuals.com. All Manuals Search And Download.
|