OWNER’S MANUAL
CRS3
In-Ceiling Loudspeaker
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER INSTALLATION
The unique integral four foot mounting system incorporated into each speaker
allows for quick installation following these easy steps:
Flange
Mounting Feet
1. If the grille is on the speaker, remove it. It may be necessary to push one or two
of the mounting screws and its attached foot towards the baffle and against
the inside surface of the grille to force the grille out of its retaining groove.
2. Attach the speaker cable observing the proper polarity with your amplifier: +
(red speaker input) to + and – (black speaker input) to – . Make sure the left
channel of the amplifier is connected to the left speaker, and the right channel
is connected to the right speaker.
3. Make sure the mounting feet are turned inward to clear the opening, and insert
the speaker into the ceiling. Position the speaker into the hole. Note: The flange
of the speaker is designed to flex and conform to any small imperfections in
the ceiling surface. Tighten the 4 screws on the front of the baffle only enough
to make the flange become snug against the ceiling. As you tighten the
screws, the feet will automatically flip into an outward position (See Figure 2),
clamping the drywall between the feet and the flange.
Figure 2
CAUTION: Over tightening may warp the baffle, crack the ceiling, cause the flange to distort, and make the grille difficult to install.
PAINTING THE SPEAKERS
If you plan to paint your speakers, we recommend that it be done prior to installation. If you decide to paint your speakers
sometime in the future, it is best to remove them by simply reversing the steps for SPEAKER INSTALLATION listed above. When
painting the speakers, the paint masks provided in the carton must be installed in place of the grille. The grilles can also
be painted. However, great care should be taken not to clog the holes, as this will greatly reduce the sound quality of the
speakers. Before painting the grilles, remove the material under grille. Place this material back in place once the grille has
been painted. SpeakerCraft recommends only light spray painting using 5 parts thinning agent to 1 part paint. Do not paint
the grilles while they are attached to the speaker. If it is necessary to paint the material under the grille, follow the same
procedure used to paint the grilles.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
CRS3
Speaker Type:
Woofer:
Small Footprint In-Ceiling
3" Full Range Aluminum Cone Woofer
8 Ohms
Impedance:
Sensitivity:
86dB 1W/1m
Frequency Response:
Power Handling:
Cut Out Dimensions:
80Hz - 16kHz
40 watts
4 1⁄4
"
(108mm)
5 1⁄8" x 3 1⁄4"
(130mm x 83mm)
Dimensions (Diameter x Depth):
In our attempt to constantly improve our products, features and specifications are subject to change without notice.
LIMITED LIFETIME WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship,
provided the speaker was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were
purchased, or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is pref-
erable to ship this product in the original shipping container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit
is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized Dealer, it is determined that the unit was defective in
materials or workmanship at any time during this warranty period, SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace
this product at no additional charge, except as set forth below. If this model is no longer available and can not be repaired effectively, SpeakerCraft,
at its sole option, may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification
to the mounting surface may be required. If mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modi-
fication. All replaced parts and product become the property of SpeakerCraft Inc. Products replaced or repaired under this Warranty will be returned
to the original retail purchaser, within a reasonable time, freight prepaid.
This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or
shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which
has not been authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions.
This warranty will be void if the Serial Number on the product has been removed, tampered with or defaced.
This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted
above, the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be
liable for any incidental or consequential damages arising out of the use or inability to use the product, even if SpeakerCraft
Inc. or a SpeakerCraft Inc. Authorized Dealer has been advised of the possibility of such damages, or for any claim by any
other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and
exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limita-
tion on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.
SpeakerCraft offers a variety of accessories to make your installation of this and other SpeakerCraft products easy, economical, and professional. Contact
your authorized SpeakerCraft Dealer for more information. For technical inquires, please call 1-800-448-0976 or e-mail us at [email protected].
We are available to assist you every weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.
940 Columbia Ave., Riverside CA 92507 | USA (800) 448 0976 Fax (951) 787 8747 International +1 951 787 0543 | www.speakercraft.com
LIT86300(Rev2)
Download from Www.Somanuals.com. All Manuals Search And Download.
|