REQUIRED TOOLS
AND MATERIALS:
Portable System
Owners Manual
•2 People
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
•Wood Board
(scrap)
•Sawhorse or
Support Table
•(2 each) Wrenches and/or
Socket Wrenches and
Sockets.
1/2"
3/4"
AND/OR
1/2"
3/4"
•Garden Hose or Sand
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 7921
Internet Address: http://www.huffysports.com
© COPYRIGHT 2005 by SPALDING
12/05
ID# M611411
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
•
•
If using a ladder during assembly, use extreme caution.
Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
•
Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to separate during play and/or during transport of the system.
Climate, corrosion or misuse could result in system failure.
If technical assistance is required, contact Customer Service.
Minimum operational height is 6'-6" (1.98m) to the bottom of backboard.
•
•
•
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
NOTICE TO ASSEMBLERS
ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted
with sand or water according to instructions. Failure to follow instructions could result in
SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
WARRANTY CARD:
Please remember to complete your product registration form either
on-line at:
or mail-in the enclosed postcard.
12/05
ID# M611411
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system...
FRONT VIEW
NOTE:
BOARD STYLE
MAY VARY
BOARD
RIM
POLE
BASE
WHEEL
CARRIAGE
ASSEMBLY
4
ID# M611411
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
1
1
2
1
1
1
1
1
1
2
4
1
1
1
1
206646
200628
226401
908200
908246
900644
203041
Tank (Black)
Wheel Axle
Wheel
Top Pole Section
Middle Pole Section with Label
Bottom Pole Section Assembly
Nut, Hex Flange, 3/8-16
Net
9
201342
201651
203104
206219
266001
203617
5E2356
Wheel Bracket
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Spacer, Wheel Axle
Bolt, Hex-Flange 5/16-18 x 2" Long
Cap
Bolt, Carriage, 3/8-16 x 1.5 Long
Tank Cap
Label, Moving System and Height Adjust.
Bolt, Carriage, 5/16-18 x 1.75 Long
Knob, Plastic, 3-sided
Rim
Washer, Flat 5/8 I.D. x 1-1/2 O.D.
Backboard Mounting Bracket
Nut, Special 3/8-NC
Washer, .406 I.D. x 1.0 O.D.
Bolt, Carriage 5/16-18 x 4
Board Spacer
2* 203084
4* 201344
1
1
2
1
3
2
2
203470
900057
203795
203309
203053
200837
4* 203100
Nut, Hex Flange, 5/16-18
Slam Jam Bracket, Black
Bolt, “Tee” 3/8-NC x 5 Long
Bracket Reinforcement, Slam Jam
Spring, Black
1
1
1
1
1
900033
203796
200318
203472
Backboard
* YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.
12/05
ID# M611411
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS IDENTIFIER
- Actual Size
#13 (1)
#25 (4*)
#21 (1)
#7 (1)
#16 (2*)
#22 (3)
#10 (2)
#11 (4)
#19 (1)
#27 (1)
#23 (2)
PARTS IDENTIFIER- Not Actual Size
#2 (1)
#8 (1)
#3 (2)
#30 (1)
#1 (1)
#14 (1)
#12 (1)
#9 (1)
#17 (4*)
#20 (2)
#29 (1)
#24 (2)
#28 (1)
#18 (1)
#26 (1)
6
ID# M611411
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION A: ASSEMBLE THE POLES
Correctly identify each pole section. Poles have an identification sticker
that will be used as a reference point in the next step.
1.
Reference Stickers
4
5
6
TOP
MIDDLE
BOTTOM
12/05
ID# M611411
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
ONCE POLE SECTIONS ARE POUNDED TOGETHER- THEY CANNOT BE TAKEN APART
Align poles using alignment marks. First, pound top
and middle poles together by bouncing them on a scrap
piece of wood on the ground as shown in FIG A. until
CAUTION!
THE IDENTIFICATION STICKER IS
2.
LOCATED 3-3/4" FROM THE END
OF THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 2-1/2"
MINIMUM OVERLAP, LEAVING 1-
1/4" BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
they no longer move toward pole identification stickers.
THEN add bottom pole section and pound together in
the same way FIG B.
FIG. B.
FIG. A.
4
IMPORTANT!
4
5
TROUGH
CANAL
1-1/2"
ID
STICKER
5"
DIMPLE
HOLE
5
6
Wood Scrap
(NOT SUPPLIED)
8
ID# M611411
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION B: ASSEMBLE THE BASE
Install wheel axle (2) through wheel bracket (9) and install wheels (3) onto
wheel axle (2) with spacers (10) as shown.
3.
4.
IMPORTANT!:
9
2
3
10
THE SPACER (10) WILL
FIT LOOSELY UNTIL
SECURED INTO THE
CAVITY OF THE BASE.
Attach wheel carriage assembly to base (1) with bolt (13), washer (22), and nut (7)
as shown. FINGER TIGHTEN - NO TOOLS REQUIRED. Assembly will be fully
tightened in next step.
7
IMPORTANT!:
22
BE SURE THAT THE
SQUARE PORTION OF THE
CARRIAGE BOLT (13) IS
PROPERLY SEATED IN
THE SQUARE CUT-OUT OF
THE WHEEL BRACKET.
1
13
12/05
ID# M611411
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach pole assembly to tank assembly as shown. Secure pole assembly to tank
and wheel bracket by turning the pole assembly clockwise as shown. Tighten
pole completely and further rotate pole until struts are aligned correctly as shown
in FIG B.
5.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
IMPORTANT!
The pole should be turned
approximately 7 complete
rotations to tighten properly.
When properly tightened, the
wheel bracket will be tight
against the base. An assistant
is recommended to hold the
base in place during this step.
FIG B
10
ID# M611411
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotate struts down and bend struts outward to line up with holes on base as
shown. Secure free ends of tank struts to tank with carriage bolt (16), washer (22),
and knob (17) as shown. Repeat for other side.
6.
WARNING!
KNOBS MUST BE TIGHTENED
COMPLETELY AND
CHECKED PERIODICALLY
FOR TIGHTNESS.
16
22
17
12/05
ID# M611411
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Mount brackets (20 & 26) to backboard and finger tighten as shown.
NOTE: Final adjustments will be made in Step 10.
7.
NOTE:
BOARD STYLE
MAY VARY
27
26
11
27
25
26
24
20
12
ID# M611411
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Slam Jam Rim to Backboard
A • Fit rim (18) securely into bracket (26) as shown (Allow "T"-bolt (27) to slip through
center hole in rim (18).
8.
B • Install reinforcement bracket (28) onto “T” bolt (27) as shown.
C • Install spring (29) onto “T” bolt (27) as shown.
D • Install special nut (21) and washer (19) onto “T” bolt (27).
E • Tighten nut (21) until flush with end of “T” bolt (27).
B
A
28
18
27
27
26
#28
19
21
C
D
29
27
19
27
E
21
12/05
ID# M611411
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Support pole and tank assembly over support table.
Carefully slide backboard components onto pole.
9.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
SAWHORSE OR SUPPORT TABLE
DO NOT LEAVE
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
OVER.
While still in the horizontal position, carefully slide
backboard components onto pole. Secure
hardware at desired position as shown and tighten
all hardware completely at this time.
10.
11.
17
NOTE:
Peel protective
film from surface
of acrylic
backboard prior
to use.
12
23
2.
1.
Attach net (8).
4.
3.
14
ID# M611411
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach height and moving label
(15) to front of pole as shown.
Regulation rim height is 10 feet.
Place assembled unit in desired location. Fill
tank with water (26 gallons/98.4 liters) or sand
12.(approx. 360 lb./163 kg) and snap tank cap
(14) in place.
13.
CAUTION!
HEIGHT ADJUSTMENT
Rest unit on support table. Remove adjustment knobs (A)
and carriage bolts (B) to extend or retract backboard and rim.
Height adjustment from 7-1/2' to 10'.
A
CAUTION!
HEIGHT AND MOVING LABEL
MUST NOT OBSTRUCT
FACTORY ATTACHED
WARNING LABEL.
WARNING
Backboard
may rotate during
height adjustment.
ADD TWO GALLONS (7.6
LITERS) OF NON-TOXIC
ANTIFREEZE IN SUB-
FREEZING CLIMATES.
B
WARNING
Do not adjust height of system
in upright position. System must
be in down position to adjust.
MOVING SYSTEM
1. While holding pole, rotate
basketball system forward
until wheels engage with
ground.
2. Move basketball system to
desired location.
3. Carefully rotate basketball
system upright.
1
2
4. Checksystem for stability.
3
5E2356
05/05
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
DO NOT LEAVE
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
OVER.
15
10 feet
(3.05 m)
NOTE:
IF USING SAND:
2 GALLONS OF
ANTI-FREEZE IS
NOT REQUIRED
12/05
ID# M611411
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|